Hunter 59153 Installation Guide

Table of Contents
www.CasablancaFanCo.com
What to Expect with
Your Installation
Congratulations on purchasing your new
Casablanca® ceiling fan! It will provide
comfort and performance in your home
or office for many years. This installation
and operation manual contains complete
instructions for installing and operating
your fan.
Tools Needed
Ceiling Options
1.888.227.2178
Ceiling Bracket
30 inches
4
Downrod
5
10
PA G E
3
PA G E
Preparation
Ladder
PA G E
2
PA G E
We are proud of our work and appreciate
the opportunity to supply you with the
best ceiling fan available anywhere in the
world.
PA G E
7 feet
Wiring
Mounting Options
To register your fan, please visit:
www.CasablancaFanCo.com/register
Blades
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
?
?
?
20
PA G E
1
18
Troubleshooting
PA G E
17
PA G E
14
Operation,
Maintenance &
Cleaning
Remote Control
PA G E
13
PA G E
PA G E
12
PA G E
Switch Housing &
Light Kit
9
PA G E
Canopy
7
PA G E
6
Save your receipt for proof of purchase.
www.CasablancaFanCo.com
What to Expect with Your Installation
1.888.227.2178
Read and Save These Instructions
If you are unfamiliar
with wiring, use a
qualified electrician.
This product conforms to UL Standard 507.
WARNINGS
30 inches
from blade tip to
nearest wall or
obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
You may need a
friend to help you.
Assess location
1
Ceilings that are more
than 34° will require an
angled mounting kit.
See page 3 for details.
Check box to see
fan weight
7 feet
From bottom
edge of blade
to the floor
Assess ceiling angle
Standard Downrod
for ceilings 8-10 feet high
2
Shorter Downrod
3
Longer Downrod
for fans installed close to ceiling
for ceilings 10 feet or higher
Select a downrod length
2
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
w.1 - To reduce the risk of fire, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor damage,
use only Casablanca Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualified electrician.
c.2 - Use only Casablanca replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
Tools Needed
www.CasablancaFanCo.com
Ladder
Pliers
Wire Strippers
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Screwdrivers
1.888.227.2178
34O
CEILING
Ceiling Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
1.888.227.2178
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
www.CasablancaFanCo.com
Use Standard Mounting
or Low-Profile Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.CasablancaFanCo.com
1.888.227.2178
r
we
o
nP
r
Tu
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
still attached.
If you are unable to do this,
call Technical Support at
1-888-227-2178.
Refer to warning w.1 on pg. 2
5
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Preparation
A
ISC R
D
D
www.CasablancaFanCo.com
DISC
D
AR
DO NOT install
the blades before
mounting the motor
and making the wire
connections.
Time Saver Tip: Get a helper
to insert grommets, found in
the
hardware bag, into the
blades while you’re doing the
next couple of steps.
Remove the shipping blocks from the
motor. Discard the screws.
Note: Some fans will have a shipping
ring instead of shipping blocks. Please
remove the ring and discard the screws.
6
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
1.888.227.2178
www.CasablancaFanCo.com
1.888.227.2178
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
3
4
10
9
8
Steps 6-10 to reassemble with new pipe
7
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
5
Slide
Slide
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Sold Separately
Shorter
Downrod
for fans installed
close to ceiling
For Standard Mount
Included
(pre-assembled)
If you need a different downrod length follow these steps:
Included
For Low Profile
For Standard Mount
Downrod
7
6
Downrod (continued)
www.CasablancaFanCo.com
1.888.227.2178
KEEP!
(not to scale)
8”
&
3/8”
STRIP
CUT
Note: The adapter cover is not
used for Low Profile mounting.
!
KEEP
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut,
but leave at least 8”
extending from the top
of the downrod.
Slide the adapter cover onto the
downrod (for standard mount only),
then hand tighten the downrod at
least 4-5 full turns until it stops.
8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
8
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Mounting Options
For Standard Mount
www.CasablancaFanCo.com
Standar
d
For Low Profile
1.888.227.2178
Mount
Low Pro
file
Put the wires and downrod
through the canopy. Let the
canopy sit loosely on top of the fan.
DO NOT PICK THE FAN UP BY
THE CANOPY OR WIRES. Once
you have chosen and placed your
canopy, lift the fan assembly and
insert the downrod ball into the
slot in the ceiling bracket.
Put the wires and downrod through
the Low Profile canopy. Let the
canopy sit loosely on top of the fan.
Note: You MUST use a shorter
downrod if installing the low profile
canopy. See page 7 for details.
9
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Wiring
www.CasablancaFanCo.com
Note: If using the optional Low
Profile canopy, you may need to
carefully tilt the fan assembly at an
angle while connecting the wires.
OM CEILING
FR
Be sure to tilt the fan AWAY from
the opening in the ceiling bracket
and ensure the fan does not fall.
green/yellow
stripe (grounding)
Using an orange wire connector
from the
hardware bag:
Connect the 3 grounding wires
(green, green/yellow stripe, or bare
copper) coming from the ceiling,
downrod, and ceiling bracket.
green/yellow stripe
FR
O
T
green/yellow
stripe
Note: To connect the wires, hold
the bare metal leads together and
place a wire connector over them,
then twist clockwise until tight.
Place the receiver on top of the downrod
assembly as shown.
OM FAN
FR
M
CEIL
KE
Receiver
1.888.227.2178
ING BR
AC
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Wiring (continued)
www.CasablancaFanCo.com
OM
FR
OM CEILING
FR
•
Connect the blue wire from the
receiver to the blue wire (or
possibly black with white stripe
wire) from the fan.
•
Connect the white (grounded)
wire from the ceiling to both the
white wire from the receiver and
the white wire from the fan.
FRO
white
FR
M FA N
OM FAN
FR
OM
white
Connect the black (ungrounded)
wire from the ceiling to the black
wire from the receiver.
black
•
blue
Connect the yellow wire from
the receiver to the black wire
from the fan.
black
•
white (grounded)
Using the orange wire connectors
from the
hardware bag:
black
(ungrounded)
blue
yellow
Using the orange wire connectors
from the remote control hardware bag:
RECEIV
ER
1.888.227.2178
RECEIV
ER
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
11
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Canopy
www.CasablancaFanCo.com
Standar
d
Screw
Holes
1.888.227.2178
Mount
Low Pro
file
For Standard Mount: Position
the canopy so that, when lifted
into place, the canopy fits into the
hanging bracket as shown.
For Low Profile: Skip this step.
Insert the two canopy screws
found in the
hardware bag.
Lift the canopy or Low Profile
canopy into place so that the
screw holes are aligned.
12
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Blades
www.CasablancaFanCo.com
Install the grommets, found in
the
hardware bag, in the blades by hand.
Place each blade between a blade iron
and medallion. Install three blade screws,
found in the
hardware bag, to attach
the medallion to the blade iron. Repeat this
process for each blade.
Lightly attach the blade irons to the motor
assembly with screws found in
the
hardware bag, then securely
tighten after all screws are attached.
13
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Switch Housing & Light Kit
Screw two upper switch housing screws
from the
hardware bag halfway into
the mounting plate on the bottom of the
motor housing. It does not matter which
two screw holes you choose.
www.CasablancaFanCo.com
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
1.888.227.2178
Insert the third upper switch housing
screw, found in the
hardware bag, into
place and then tighten all three screws.
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the
switch housing fixture falling.
14
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Switch Housing & Light Kit (continued)
If installing the LED light: Slide the switch
housing cap through the hole in the center of
the LED assembly. Remove the dummy terminals
from the blue and white pin connectors in the
switch housing. Connect the pin connectors
from the switch housing and the LED assembly.
If installing the No-Light Cap: Skip this step.
www.CasablancaFanCo.com
Connect the 9-pin plugs from the upper and
lower switch housings. Make sure to line up
the colored markings on the connectors.
1.888.227.2178
Install the three lower switch housing
screws, found in the
hardware bag,
into place and then tighten all three
screws securely.
Make sure the lower switch housing is securely attached to the
upper switch housing. Failure to properly secure all 3 assembly
screws could result in the switch housing fixture falling.
15
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Switch Housing & Light Kit (continued)
www.CasablancaFanCo.com
Tab
Notch
If installing the LED light:
Attach the LED assembly to the
switch housing by installing
two light kit assembly screws,
found in the
hardware bag,
through the slots, not the screw
holes.
If installing the No-Light Cap:
Skip this step.
Attach the switch housing cap
to the lower switch housing by
installing two light kit assembly
screws, found in the
hardware
bag.
Position the notches in the outer rim
of the globe or no-light cap so they
line up with the tabs on the inside
rim of the upper switch housing.
Carefully lift the globe or no-light
cap up as far as it will go, then rotate
clockwise until it is held tightly in
place by the tabs.
16
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
1.888.227.2178
Remote Control
Battery
Door
www.CasablancaFanCo.com
er
w
o
nP
r
Tu
ON
CONGRA
T
U
YOU’RE LATIONS!
DONE!
Phillips
Head
Screw
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the transmitter assembly. The
battery should be installed with the positive
(+) side up. Replace with a CR2032 battery
when necessary.
1.888.227.2178
The remote transmitter is already paired
to the receiver and ready to use.
Note: If you would like to operate
multiple fans or multiple remotes,
or if your remote is not working,
please see the Troubleshooting
section at the end of this manual.
17
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
See next page for fan
operation instructions.
Operation, Maintenance & Cleaning
www.CasablancaFanCo.com
1.888.227.2178
Reverse
Switch
The Fan Off button found on the right side of
the transmitter turns the fan off.
Buttons 1 through 4 turn on the fan and
control the speed.
• (1) Extra Low
• (2) Low
• (3) Medium
• (4) High
The up arrow and down arrow buttons control the
lights on the fan. Quickly press and release the up
or down arrow to turn the lights off and on. Hold
the up or down arrow to raise or dim the light level.
Dimming Mode: To enable dimming, you must
first set your remote to Dimming Mode. To toggle
Dimming Mode on or off, hold down the Fan Off
button while pressing the Light Down arrow twice.
18
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
To change the direction of air flow, move the
reverse switch to the opposite position. You
must remove the globe or no-light cap in
order to access the reverse switch.
Operation, Maintenance & Cleaning (continued)
www.CasablancaFanCo.com
1.888.227.2178
Safe-Exit
The Safe-Exit Program gives you about
thirty seconds of light when you turn the
lights off to exit the room before the lights
go out. To use Safe-Exit:
• Press the Fan Off button for at least three
seconds to initiate the Safe-Exit Mode.
• The lights will flash for visual confirmation.
• The lights will stay on 50% brightness for
15 seconds and then begin to dim. After
a total of 30 seconds, the lights will be
completely off.
Post
For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the finishes.
Your Universal Remote comes with a wall
plate that has two posts on which to mount
your transmitter when not in use.
19
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
Troubleshooting
www.CasablancaFanCo.com
Fan doesn’t work
Excessive wobbling
Remote does not work
• Press a fan speed button (1-4).
• Tighten all of the blade and
blade iron screws until they
are snug.
• Make sure the battery is installed
correctly.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the remote control
battery is working.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on pages 10-11.
• Check the plug connections in
the switch housing.
• Install a new battery.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• If the remote still does not
work, you may need to pair
your remote. To prevent faulty
operation, please disconnect
power (at the wall switch,
breaker, or fan) from all other
ceiling fans within range while
pairing. To pair: cycle power
to the fan by turning power off
and back on at the wall switch
(or circuit breaker if necessary).
Within three minutes, press and
hold both the Fan Off button and
the 4 button for four seconds to
pair the remote. If applicable, the
fan will turn on and the lights
will flash and stay on to indicate
successful pairing.
• Use the provided balancing
kit and instructions to balance
the fan.
Noisy Operation
• Tighten the blade and blade
iron screws until they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
20
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company
1.888.227.2178
AUTHORIZED SERVICE
CENTERS
For the most updated list of
Casablanca Authorized Service
Centers, visit
www.CasablancaFanCo.com or
call toll free 1-888-227-2178.
LED lights will not dim
• To enable dimming, you
must first set your remote to
Dimming Mode. To toggle
Dimming Mode on or off, hold
down the Fan Off button while
pressing the Light Down arrow
twice.
Troubleshooting (continued)
www.CasablancaFanCo.com
Installing Multiple Fans with Independently Operating Remote Controls
1.888.227.2178
Installing One Fan Operating on Multiple Remote Controls
To install multiple fans with independently operating remote controls, there is no need to
perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply
install each receiver into a fan and use the appropriate transmitter to operate each fan.
To have multiple remote controls operate one fan, you must pair each additional transmitter
to the receiver in the fan. The transmitter that shipped with your fan is already paired.
Note: To prevent faulty operation, please disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while pairing.
If your remote is not working, see the “Remote does not work” section on the previous page.
For each additional transmitter, cycle power to the fan by turning power off and back on at
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.
Installing Multiple Fans Operating on a Single Remote Control
“Unpairing” Procedure for Faulty Operation of Remote Controls
X
To have multiple fans operated by a single remote control, you must pair the transmitter to each
additional receiver. The receiver that shipped with your fan is already paired to the transmitter.
If a transmitter is mistakenly operating a fan, you need to “unpair” the transmitter from that
fan’s receiver. The “unpairing” procedure is the same as the pairing procedure.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while pairing each fan.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,
breaker, or fan) from all other ceiling fans within range while “unpairing” a fan.
For each additional fan, ensure that a compatible receiver is installed. Disconnect power from all
other fans while pairing. To pair: cycle power to the fan by turning power off and back on at
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.
Disconnect power from all other fans while “unpairing.” Then, cycle power to the fan you
wish to “unpair” by turning power off and back on at the wall switch (or circuit breaker
if necessary). Within three minutes, press and hold both the Fan Off button and the 4
button for four seconds to “unpair” the remote. If applicable, the fan will turn off and the
lights will flash and turn off to indicate successful “unpairing.”
21
M8527-01 • 04/16/15 • © 2015 Casablanca Fan Company