Hunter 59085 Installation Guide

www.HunterFan.com
Table of Contents
Tools Needed
Mounting Options
Ceiling Bracket
30 inches
To register your fan, please visit:
www.HunterFan.com/register
Wiring
12
Troubleshooting
?
?
?
17
PA G E
16
PA G E
1
M3531-01 • 06/05/13 • © Hunter Fan Company
15
11
Operation,
Maintenance & Cleaning
PA G E
PA G E
14
5
Light Kit
PA G E
Remote Control
PA G E
Globe
4
Canopy
10
PA G E
6
Save your receipt for proof of purchase.
3
PA G E
Downrod
Ladder
PA G E
2
PA G E
7 feet
PA G E
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
What to Expect with
Your Installation
PA G E
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or office for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
1.888.830.1326
www.HunterFan.com
What to Expect with Your Installation
1.888.830.1326
Read and Save These Instructions
This product conforms to UL Standard 507.
If you are unfamiliar
with wiring, use a
qualified electrician.
WARNINGS
w.1 - To reduce the risk of fire, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
Know your wiring
You may need a
friend to help you.
Assess location
1
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
7 feet
from bottom
edge of blade
to the floor
Assess ceiling angle
2
Standard Downrod
for ceilings 8-10 feet high
Longer Downrod
for ceilings 10 feet or higher
Select a downrod length
2
M3531-01 • 06/05/13 • © Hunter Fan Company
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor damage,
use only Hunter Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualified electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
www.HunterFan.com
Tools Needed
Ladder
Pliers
Wire Strippers
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
M3531-01 • 06/05/13 • © Hunter Fan Company
Screwdrivers
1.888.830.1326
34O
CEILING
www.HunterFan.com
Mounting Options
OPTION 1
If you have a flat ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
You need ONLY
a Longer
Downrod
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by a standard downrod (included).
1.888.830.1326
1.866.268.1936
Use Standard Mounting
to hang the fan from a flat ceiling.
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
4
M3531-01 • 06/05/13 • © Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.HunterFan.com
1.888.830.1326
r
we
o
nP
r
Tu
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
still attached.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
M3531-01 • 06/05/13 • © Hunter Fan Company
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
www.HunterFan.com
1.888.830.1326
skip to next page
Standard
Downrod
for ceilings 8-10’ high
Steps 1-5 to remove standard downrod pipe
1
2
3
4
10
9
8
Steps 6-10 to reassemble with new pipe
6
M3531-01 • 06/05/13 • © Hunter Fan Company
5
Slide
Slide
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Sold Separately
Option 2
If you need a different downrod length follow these steps:
Included
(pre-assembled)
Option 1
Downrod
7
6
www.HunterFan.com
Downrod (continued)
1.888.830.1326
Hanger
Ball
!
KEEP
Adapter
Cover
Slide the adapter cover onto the downrod
until it rests against the hanger ball.
Remove the pre-installed setscrew so that
the downrod can be inserted.
7
M3531-01 • 06/05/13 • © Hunter Fan Company
Hand tighten the downrod (at least 4-5
full turns) until it stops.
www.HunterFan.com
(not to scale)
8”
&
3/8”
1.888.830.1326
STRIP
CUT
Downrod (continued)
The wires can be cut, but leave at least 8”
extending from the top of the downrod.
Tighten the setscrew with pliers.
DO NOT HAND TIGHTEN.
8”
3/8”
If the setscrew is not tightened
securely, the fan may fall.
8
M3531-01 • 06/05/13 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
9
M3531-01 • 06/05/13 • © Hunter Fan Company
1.888.830.1326
Wiring
www.HunterFan.com
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
CEILIN
G
OM
FR
T
KE
black (live in)
FR
black (ungrounded)
M FA N
white (neutral in)
FRO
Using an orange wire
connector from
the
hardware bag,
connect the black wire
(ungrounded) from the
ceiling to the black wire
from the receiver (marked
“live in”). Connect the
white wire (grounded)
from the ceiling to
the white wire from
the receiver (marked
“neutral in” or
“common in”).
white (grounded)
C
blue
A
ING BR
CEILIN
G
OM
FR
blue (light out)
CEIL
black
M
white
green/yellow stripe
O
FR
Using an orange wire
connector from
the
hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
RECEIVE
R
black (fan out)
green/yellow stripe
Using the blue wire
connectors from the remote
control hardware bag,
connect the white wire
from the receiver (marked
“common out”) to the white
wire from fan. Connect the
black wire from the receiver
(marked “fan out”) to the
black wire from the fan.
Connect the blue wire from
the receiver (marked ”light
out”) to the blue wire from
the fan. The red wire from
the receiver will not be used,
it has a pre-installed wire
terminator.
white (common out)
green/yellow stripe
(grounding)
OM FAN
FR
OM
FR
1.888.830.1326
OM
RECEIV
ER
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
M3531-01 • 06/05/13 • © Hunter Fan Company
www.HunterFan.com
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
Note: Fan style may vary.
11
M3531-01 • 06/05/13 • © Hunter Fan Company
1.888.830.1326
www.HunterFan.com
Light Kit
To attach the light kit top housing, partially
install two housing assembly screws, found in
the
hardware bag, into the light kit mounting
plate.
Align the keyhole slots in the housing with the
housing assembly screws.
Use only the light fixture supplied with this fan model.
12
M3531-01 • 06/05/13 • © Hunter Fan Company
1.888.830.1326
www.HunterFan.com
Light Kit (continued)
1.888.830.1326
Screw
Holes
Connect the upper plug connector from the
motor to the lower plug connector in the light kit.
Turn the light kit top housing counterclockwise
until the housing assembly screws are firmly
situated in the narrow ends of the keyhole
slots. Install the remaining screw into the
housing. Tighten all three screws firmly.
Note: Both plug connectors are polarized and
will only fit together one way. Make sure the
connectors are properly aligned before connecting
them. Incorrect connection could cause improper
operation and damage to the product.
Make sure the light kit top housing is securely attached to the light kit mounting
plate. Failure to properly attach and tighten all three assembly screws could result in
the light kit top housing and light fixture falling.
13
M3531-01 • 06/05/13 • © Hunter Fan Company
www.HunterFan.com
Globe
1.888.830.1326
CONGRA
YOU’RETULATIONS!
DONE!
Lift the globe up to the light kit top
housing. Align the three bolts on the
globe with the three slots in the light
kit top housing.
Rotate the globe clockwise until tight.
See next page for fan
operation instructions.
14
M3531-01 • 06/05/13 • © Hunter Fan Company
Remote Control
www.HunterFan.com
1.888.830.1326
High
Medium
Low
Fan Off
Battery
Door
Light
High
Fan Off
Phillips
Head
Screw
To access the battery compartment,
remove the small Phillips head screw that
secures the battery door to the transmitter
assembly. The battery should be installed
with the positive (+) side up. Replace with
a CR2032 battery when necessary.
Turn Power
ON
Note: The remote must be paired before
the fan will operate.
Within 3 minutes of restoring power to
the fan, press both the Fan Off button and
the High button for at least 4 seconds. Your
fan will turn on low to indicate successful
syncing. If it does not, turn off power to
your fan, wait 1 minute then try again. If
using the transmitter with multiple fans,
repeat this process for each fan.
15
M3531-01 • 06/05/13 • © Hunter Fan Company
The Fan Off button only turns the fan off.
To turn the fan on, press one of the fan
speed buttons.
ooo High
oo Medium
o
Low
Quickly press the Light button to turn the
lights off and on.
Operation, Maintenance, & Cleaning
www.HunterFan.com
1.888.830.1326
Safe-Exit
The Safe-Exit Program gives you about
thirty seconds of light when you turn
the lights off to exit the room before the
lights go out. To use Safe-Exit:
• Press the Fan Off button for at least
three seconds to initiate the Safe-Exit
Mode.
• The lights will flash for visual
confirmation.
• The lights will stay on 50% brightness
for 15 seconds and then begin to dim.
After a total of 30 seconds, the lights
will be completely off.
To install the transmitter cradle,
remove the two screws holding
your switch cover plate. Do not
remove the cover plate. Orient
the cradle by lining up the two
mounting holes with those on the
cover plate. Insert and tighten the
screws. Do not over tighten.
When cleaning the fan, use
soft brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
When the fan is turned on,
centrifigual force will cause the
blades to emerge from the center
of the fan, spinning. Keep the area
around the fan clear so nothing is
hit or knocked over by the blades
when they swing out. When the fan
is turned off, the blades will slowly
retract back into the center of the fan.
16
M3531-01 • 06/05/13 • © Hunter Fan Company
Note: For CFL lighting, the lights will stay
on 100% brightness for 30 seconds. After
a total of 30 seconds, the lights will be
completely off.
www.HunterFan.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
Noisy operation
• Make sure power switch is on.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Check to see if any of the blades
are cracked. If so, replace all of the
blades.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 10.
Remote control of fan is erratic
• Make sure the battery is
installed correctly.
• Install a fresh battery.
Transmitter only works when
held at close range
• Change battery.
17
M3531-01 • 06/05/13 • © Hunter Fan Company
1.888.830.1326