Security Point Infrared Mini high speed dome User manual

Mini IR High Speed Dome Camera
User Manual
Please read this manual thoroughly before use or installation
and keep it handy for fureture reference
WARNINGS AND CAUTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS
THROUGH VENTILATION GRILLS OR OPENINGS ON THE EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user the presence of non-insulated “dangerous voltage” within the product’s
enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to
different persons.
The exclamation point within an equilateral triangle, is intended to alert the user the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying this product.
IMPORTANT SAFEGUARDS
1. Read these instructions before attempting installation or operation of dome device.
2. Keep these instructions for future reference.
3. Heed all warnings and adhere to electrical specifications. Follow all instructions.
4. Clean only with non abrasive dry cotton cloth, lint free and approved acrylic cleaners.
5. Should the lens of the camera become dirty, use special lens cleaning cloth and solution to
properly clean it.
6. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.
7. Use only attachments or accessories specified by the manufacturer.
8. Verify that the surface you are planning to use for attaching the dome can adequately support
the weight of the device and mounting hardware.
9. Protect this device against lighting storms with proper power supplies.
10. Refer all servicing to qualified service personnel. Servicing is required when the device has
been damaged in any way, when liquid traces are present, or the presence of loose objects is
evident or if the device does not function properly, or has received sever impact or has been
dropped accidentally.
11. Indoor dome is for indoor use only and not suitable for outdoor or high humidity locations.
Do not use this product under circumstances exceeding specified temperature and humidity
ratings.
12. Avoid pointing the camera directly to the sun or other extremely bright objects for prolonged
period of time avoiding the risk of permanent damages to the imaging sensor.
13. The attached instructions are for use by qualified personnel only. To reduce the risks of
electric shock, do not perform any servicing other than contained in the operating instructions
unless you are qualified to do so.
14. During usage, user should abide by all electrical safety standards and adhere to electrical
specifications for the operation of the dome. The control cable for RS485 communications as
well as the video signal cables should be isolated from high voltage equipment and high voltage
cables.
15. Use supplied power supply transformer only.
INDEX
1 Product Introduction ...................................................................................................... 1
1.1 Package Contents ...................................................................................................... 1
1.2 Specification ............................................................................................................... 2
1.3 Performance Features ................................................................................................ 3
1.4 Function Description................................................................................................... 4
2 Installation ....................................................................................................................... 6
2.1 Product Dimension ..................................................................................................... 6
2.2 Bracket Dimension ..................................................................................................... 6
2.3 Installation .................................................................................................................. 7
2.4 Connection ................................................................................................................. 7
3. Instruction ...................................................................................................................... 8
3.1 Power On Action......................................................................................................... 8
3.2 Basic Function ............................................................................................................ 8
3.3 Special Function ......................................................................................................... 9
3.4 Screen Character Operation .................................................................................... 10
4 OSD Menu...................................................................................................................... 11
4.1 System ..................................................................................................................... 12
4.2 Dome Function ......................................................................................................... 12
4.2.1 Preset ................................................................................................................ 12
4.2.2 Scan .................................................................................................................. 13
4.2.3 Guard Tour ......................................................................................................... 13
4.2.4 Pattern ............................................................................................................... 14
4.2.5 Privacy Zone ...................................................................................................... 14
4.2.6 Other .................................................................................................................. 15
4.2.7 Alarm ................................................................................................................. 15
4.3 Camera .................................................................................................................... 16
4.3.1 CAM ADV........................................................................................................... 16
4.3.2 CAM AE ............................................................................................................. 16
4.4 IR.............................................................................................................................. 17
4.5 Display ..................................................................................................................... 17
4.6 Time ......................................................................................................................... 17
4.7 Language ................................................................................................................. 18
4.8 Reset ........................................................................................................................ 18
Appendix Ⅰ Anti-lightning, Anti-surges ........................................................................ 19
Appendix Ⅱ Clean Transparent Cover ........................................................................... 19
Appendix Ⅲ Common Knowledge on RS-485 Bus ....................................................... 20
1. Basic Feature of RS-485bus ...................................................................................... 20
2. Mode of Connection and Terminal Resistance ........................................................... 20
Appendix Ⅳ Exception Handling ................................................................................... 21
Copyright Statement ........................................................................................................ 22
* Indicates the functions with default protocol, it might not function by using other protocols
※ Indicates the optional functions, only with certain mode
1 Product Introduction
1.1 Package Contents
IR speed dome
1pc
Wall mount bracket
1pc
Power supply
1pc
Screws kits
1pc
User manual
1pc
1
1.2 Specification
Horizontal Rotation Speed
Tilt Rotation Speed
Horizontal Rotation Range
Tilt Rotation Range
Auto Flip
Ratio Speed
Auto control IR LED
IR Testing Time
Ambient Light Testing
IR Illumination On
IR Output Power
IR Standby Power
IR Standby Time
A-B Scan
A-B Scan Speed
360° Scan Speed
Dwell Preset
Preset Points
Go to Preset Speed
Guard Tours
Guard Points
Pattern Scan
Pattern Scan Record
Park Time
PWR on Action
Park Action
Communication Protocol
Communication
Baud Rate
Soft ID
Privacy Mask
Time Scheduling function
Alarm
Timing Run
Operating Temperature
Operating humidity
Heater & Blower
Power
Lightning protection
IR Illumination Distance
Power Consumption
LED Type
Camera Specification
2
0.02°-200°/s
0.02°-120°/s
360°
93°
Horizontal 180°, Vertical 93°
Support
PWM
2-15s selectable
0-50 grades
0-25 grades selectable
1-9 grades selectable
1-9 grades selectable
2-15s selectable
User programmable
1-9 speed setting available
1-9 speed setting available
5-60s interval
220
200°/s
4 groups
Max.16 points, dwell time user selectable
4 pcs
max.15 minutes, max.512 commands
1-60mins available
Memory/Pattern/Tour/360° scan/A-B scan/Preset 1-8/None
Pattern/Tour/360° scan/A-B scan/Preset 1-8/None
Pelco-D, Pelco-P
RS-485 Bus
2400/ 4800/ 9600bps
1-255
Support (according to zoom module type)
8 tasks
4 inputs and 2 outputs (Optional)
Built-in high precision RTC clock, support time management
Indoor: 0°~ +40°
Outdoor: -40°~ +60°
≤95% Non Condensing
Auto temperature control
AC/DC15-28V ≤3A
Transient voltage 6000V
50M
≤ 15W
Ø 16=6
Please refer the last page of user manual
1.3 Performance Features

PWM function. Intelligent IR illumination & power consumption is variable, dependant
the zoom factor.

3D allocation. That screen coordinate location and zoom local are performed at the
same time can be available.

Privacy masking. 24 privacy masking areas can be random set (module support).

Supported Protocols. Pelco-D/P; Others on special request.

4 path patterns. Each path can record 512 different instructions or 900s path
operation.

Manual control speed. The lowest 0.02º/s smooth running can be available.

4 guard groups. The dwell position and time of 16 preset points of each group can
be edited independently.

Optional IP module (built in provision).

Built-in high density RTC clock supports time management function.

Optional alarm, 4 alarm inputs and 2 alarm outputs.

Park action. If users don’t operate the dome in set time, it will automatically run
preset guard group, trace memory group, pan scan etc.

Memory of operation before power off.

Built-in fan and heater can control the temperature automatically.
Heater works below 0℃ and fan works above 40℃.

Multiple languages for OSD menu, English, Chinese etc.

Illumination to ambient light can be adjustable.

Accurate step motor control makes it stable running, precise location and sensitive
reaction.
3

Completed metal body construction, waterproof IP 66.

Built-in 6000V anti-lighting and anti-surge protection equipment.
1.4 Function Description
Alarm Linkage
Intelligent dome camera supports 4 switch alarm inputs, 1 switch output and 1 digital output.
When the dome camera has detected the alarm closed signal, it will run the preset action which
can be one of the calling preset points or no action.
Auto-adaptive to Protocol and Module
The dome can auto-adaptive to the multi protocol and most of the module without changing the
DIP switch.
3D Allocation
With this function users can move the image of some area to the center of screen according to
specified level and vertical coordinates and auto control to zoom according to zoom parameter
set. Screen coordinate location and zoom local can be available via the software support.
Privacy Masking
In the monitoring scope, areas that users can’t or aren’t willing to make show in the screen of
the monitor can be set as privacy protected area (area masking), such as area where
customers enter the password in monitoring system of bank or some doorway.
Trace Memory (Pattern Scan)
The traces of camera’s any running action in every directions of PTZ can be saved, which is
called pattern scan. In pattern scan the camera turning to up, down, left and right and zooming
in or out can be saved. This function remembers and imitates a process of operator’s operation.
This dome camera has 4 path patterns. Each path can record 512 different instructions or the
longest 15mins’ path operation. Opening any one of the paths can remember automatically the
present running trace and scan cyclically according to the recorded trace.
Zero Alignment
There is a point specified as zero point. When the dome is working, the preset point is not
accurate caused by the operator. User can make the dome automatically enable the zero
alignment by operational order.
Auto Flip
In the manual scanning mode, when beyond the maximum angle in tilt and if the joystick is held
continuing in tilt direction, the dome will automatically rotate 180 degree in horizontal direction
to maintain continuity of scanning. So vertical 180° continuous monitoring comes true.
Focus
The auto focus enables the camera to focus automatically to maintain clear image. User can
use manual focus to get expected image in special condition.
Under the following conditions camera will not auto focus on the camera target:
(1) Target is not in the center of the screen;
(2) Attempting to view images that are far and near at the same time;
(3) Target is strongly lighted object, such as neon lamp, etc.;
4
(4) Targets are behind the glass covered with water droplets or dust;
(5) Targets are moving quickly;
(6) Monotonous large area targets, such as wall;
(7) Targets are too dark or faint.
BLC(Back Light Compensation)
If the light of background is bright, the target in the picture may appear dark or as a shadow.
BLC enhances exposure of the target in the center of the picture. The dome adjusts the iris
according to the center of the pictures. If there is a bright light source outside this area, it will
wash out to white. The camera will adjust the iris so that the target in the sensitive area will be
properly exposed.
Iris Control
Factory default is automatic camera aperture, in mode of which camera senses changes in
ambient light through moving and adjust automatically lens aperture to make the brightness of
output image stable.
Ratio Speed
Intelligent pan and tilt speed is variable depend on the zoom factor. When zooming in, the
speed will become slower and when zooming out, the speed will become faster.
360 Scan
Dome 360°clockwise continuously scans the display scene at set speed in horizontal direction
under the condition that pitch angle remains the same. In the scanning status, operator can
move the joystick to exit from scanning.
Preset
After the dome camera keeps arbitrary PTZ location, it will automatically move to the defined
position when preset is called.
Guard Tour Scan
Dome patrol scans according to certain edited preset order.
Limited Points Scan (A-B Scan)
The dome operates reciprocating scanning the real scenarios at a certain speed between the
set left and right points. The range of left and right points boundary is 20° - 340°.
Power Off Memory
This feature allows the dome to resume its previous preset or status after power is restored. By
default setting, the dome support power up memory, which improves the reliability and avoids
repeated settings of the parameter.
Park Action
If users don’t operate the dome in set time, it will automatically run preset specific mode (pan
scan, A-B scan, park action, cruise, preserve action etc.).
Multilanguage OSD Menu
The available language on screen menu can be English, etc. User can set the function or
5
parameter, or check the related information through the OSD.
Return to PTZ Function
Return dome’s pan and tilt and camera zoom value to the control device.
2 Installation
2.1 Product Dimension
2.2 Bracket Dimension
6
2.3 Installation
2.4 Connection
Connection of RS485
Before connecting, please turn off the power and read carefully the instructions of all connected
devices. Please use the standard power we supply and don’t lengthen the power cable
arbitrarily.
Fig 24
7
3. Instruction
3.1 Power On Action
When initializing the system, the operation as left figure will run
in 2 seconds.
IR SPEED DOME
PROTOCOL
COMM
DOME ID
MODULE
VERSION
PAN
TILT
PELCO-D/P When restoring out-of-factory settings, please wait patiently.
2400.N.8.1 The operation as left figure will run in 1 minute.
001
This left figure means initializing the pan/tilt motor of speed
dome camera.
V1.2
INIT
INIT
POWER ON
IR SPEED DOME
PROTOCOL
COMM
DOME ID
MODULE
VERSION
PAN
TILT
PELCO-D/P
2400.N.8.1
001
V1.2
OVER
OVER
The initialization of pan/tilt motor completes. It is initializing the
camera and detecting the module of camera.
.
POWER ON
IR SPEED DOME
PROTOCOL
COMM
DOME ID
MODULE
VERSION
PAN
TILT
PELCO-D/P
XXX is the specific model of camera module which is
2400.N.8.1
displayed after camera finishes detection.
001
XXX
Power on self testing completes.
V1.2
OVER
OVER
POWER ON
3.2 Basic Function
Dome Running
Control joystick or up, down, left and right key in the keyboard.
Zoom
8
Press ZOOM- button to make the lens farther and minify the scene.
Press ZOOM+ button to make the lens closer and magnify the scene.
Focus
After FOCUS- button is pressed, the object in vicinity will become clearer while the object far
away will become ambiguous.
After FOCUS+ button is pressed, the object far away will become clearer while the object in
vicinity will be ambiguous.
Iris
Press IRIS- to gradually shrink the iris and decrease the image brightness.
Press IRIS+ to enlarge the iris and increase the image brightness.
Preset Point
Setting preset, press button “preset” + ”number” + ”enter”.
Calling preset, press button “call” + ”number” + ”enter”.
Deleting preset, press button “clear” + ”number” + ”enter”.
Remark: Some preset points are used tentatively for special functions.
3.3 Special Function
The follow presets are predefined as special function, please shot+ preset No.+ enter to enable
those functions:
PREST
33
34
75
76
77
78
79
80
81
82
83
84
85
FUNCTION
Pan scan180 º
Reset
Trace memory 1
Trace memory 2
Trace memory 3
Trace memory 4
Digital zoom on
Digital zoom off
Auto day/night
Switch to night
Switch to day
Force on far light
PRESET
86
87
88
89
91
92
93
94
95
96
97
98
FUNCTION
BLC on
BLC off
Freeze on
Freeze off
Limited Points Scan (A-B scan)
Set left point of A-B scan
Set right point of A-B scan
OSD menu off
OSD menu on
Guard tour 3
Guard tour 2
Guard tour 1
Force on near light
99
Pan scan
Note: If use some other equipments to control IR dome, some special functions probably can’t
be effective because of the limit of protocol.
9
3.4 Screen Character Operation
Call preset 95 to enter the OSD, call preset 94 to exit the OSD.

Up or Down: Move the option of the OSD, change the value on the OSD.

Right: Enter the option, select the item or confirm.

Left: Return to main menu or cancel.

Zoom Display: x XXX, XXX is the present zoom of camera.

Time Display: XXXX(year)-XX(month)-XX(day)

Angle Display: XXX.XX(pan)/XXX.XX(tilt)

IR Display: ☀means the IR display status is on.
Remark: “-”means the cursor selecting some option. “
options.
10
XX(hour)-XX(minute)-XX(second)
means the IR is on.
” means editing the content of some
4 OSD Menu
11
4.1 System
<MAIN MENU>
<SYSTEM>
<DOME>
<CAMERA>
<IR>
<DISPLAY>
<TIME>
<LANGUAGE>
<RESET>
EXIT

<SYSTEM>

PROTOCOL: Display the protocol of the dome.

COMM: 2400. N. 8. 1 means the communication
information. 2400 is baud rate. COMM form: Baud rate.
Check bit. Data bit. Start bit.

DOME ID: Display the dome address. The range is
000-255.

MODULE: Display the brand and model of camera.

VERSION: Version will be updated along with the
product upgrading.
<SYSTEM>
PROTOCOL
COMM
DOME ID
MODULE
VERSION
< COMM SET>
PELCO-D/P
2400.N.8.1
001

EXIT

DEVICE ID: It is only and used to distinct from the
ID of other domes.

CHECK ID: Distinguishing several domes with same
ID and altering target ID, soft protocol and baud rate
need to enter check ID in line with the device ID,
otherwise altering can’t be completed.

TARGET ID: Target ID can be changed and edited
on line. It will be effective immediately after changed.
“Dial the address number” on this mini dome is not
available.

BAUD RATE: Baud rate is selectable. 1200, 2400,
4800, 9600 are available. Default is 2400.
<COMM SET>
DEVICE ID
CHECK ID
TARGET ID
BAUD RATE
SAVE
EXIT
<COMM SET>
001
2400
4.2 Dome Function
4.2.1 Preset
<PRESET>
PRESET NO
CALL PRESET
<SET PRESET>
EXIT


001
PRESET NO: Select the preset number needing
to be operated, whose range is
001-220.

CALL PRESET: Call the preset number edited.
<SET PRESET>
Entering SET PRESET displays the content as left
figure. Call preset 1 to save and call preset 2 to
12
<PRESET>
PRESET NO
CALL PRESET
<SET PRESET>
PRESET 1: SAVE
PRESET 2: BACK
back.
001
Because some presets are used to realize special
functions, they can not be set and called normally.
4.2.2 Scan

SCAN
SCAN SPEED
SCAN SPEED: Scan speed includes setting the
speed of limited points scan (A-B scan) and
5
360°scan. Its range is 1-9 grades.
EXIT
Note: The effective range of left and right boundary is 20-340°.
4.2.3 Guard Tour
This dome camera can set 4 groups of guard tour. Each group has 16 points and each point
can be set alone the dwell time and tour speed.
<GUARD TOUR>
GUARD TOUR NO
CALL GUARD TOUR
<GUARD TOUR >
EXIT
1

GUARD TOUR NO: It has 1-4 groups settable.

CALL GUARD TOUR: Call the guard tour ID edited
successfully.
<GUARD TOUR>
<GUARD TOUR>
ID POINT TIME SPEED
01
01
05
64
02
02
05
64
03
03
05
64
04
04
05
64
05
05
05
64
06
06
05
64
07
07
05
64
08
08
05
64
<NEXT PAGE>

ID: The tour sequence of guard tour group. Its range
is 1-16.

POINT: The preset of guard tour. Its range is 01-64
settable.

is

TIME: The default time of all points is 05s. Its range
05-60s.
SPEED: The speed between two points in each
guard tour group can be set alone. Its range is 1-64
grades.
<GUARD TOUR>
ID POINT TIME SPEED
09
09
05
64
10
10
05
64
11
11
05
64
12
12
05
64
13
13
05
64
14
14
05
64
Note: Preset 33 and 34 can’t be set as guard tour point.
15
15
05
64
16
16
05
64
SAVE
13
4.2.4 Pattern
<PATTERN>
PATTERN NO
CALL PATTERN
<PATTERN>
EXIT

1
Select the pattern needing to be edited. 1-4 pattern are
effective.


<PATTERN>
PATTERN NO
CALL PATTERN
<PATTERN>
1
PATTERN NO: Factory default is 1.
CALL PATTERN: Call the patterns having been
edited.
<PATTERN>
Left figure shows the status when entering to the pattern set.
“XXX” means the quantity of operator’s running pattern, and
512 is the most amount of the instruction.
Remark: The precision of pattern is associated with the system
settings and the module of camera. When using the pattern,
the user is recommended to turn off the privacy zone and
unnecessary display function.
XXX/512
PRESET 1: SAVE
PRESET 2: BACK
4.2.5 Privacy Zone

<DOME>
<PRESET>
<SCAN>
<GUARD TOUR>
<PATTERN>
<PRIVACY ZONE>
<OTHER>
<ALARM >
EXIT
depends on the module supported.


1: Move the cursor to MASK NO, which is be selected by
pressing the right key of direction.
2: Press the “up and down” keys in the keyboard to edit the
mask number as 1, which is be entered by pressing the
ON
<PRIVACY ZONE>
MASK NO
01
MASK
ON
<SET MASK>
14
MASK: ON and OFF are selectable.
Example of Setting Mask 1
EXIT
PRESET 1: SAVE
PRESET 2: BACK
SET MASK: For detailed steps, please refer to the
“Example of Setting Mask 1”.
<PRIVACY ZONE>
MASK NO
MASK
<SET MASK>
MASK NO: Select the mask number. It
right key. “-” means selecting this mode, while “
editing this mode.
” means
3: Move the cursor to <SET MASK> and press right key to set
the position of privacy zone. See the figure on the left below.
4: Shake the joystick to aim at the object. Use the ZOOM+ and
ZOOM- keys in the keyboard to adjust the size of picture. And
use iris OPEN and CLOSE keys to adjust the size of mask. Call
preset 1 to save and exit and call preset 2 to exit directly.
Remark: The mask size is better more than double the target
size. Setting mask is associated with the pitch angle which is
advised equal to or less than 45°by the factory.
4.2.6 Other
<DOME>
<PRESET>
<SCAN>
<GUARD TOUR>
<PATTERN>
<PRIVACY ZONE>
<OTHER>
<ALARM >
EXIT
<OTHER>
PARK MODE
NONE
PARK TIME
05
POWER ON ACT MEMORY
RATIO SPEED
ON
AUTO FLIP
ON

PARK MODE: There are 13 actions of NONE,
Pattern 1, Tour 1, 360 scan, AB scan, Preset 1-8
selectable.

PARK TIME: The dome camera runs home
position after a period of idle time which is home time
and whose range is 1-60 mins.

POWER ON ACT: There are 14 actions of Memory,
Pattern 1, Tour 1, 360 scan, AB scan, Preset 1-8,
NONE selectable.

RATIO SPEED: Ratio speed can be set as ON or
OFF status.

AUTO FLIP: The dome camera operated flips
horizontally 180° when beyond the maximum angle. If
continuing withholding the joystick when beyond the
maximum angle in tilt, it flips horizontally 180°and 0°in
tilt. So vertical 180°whole continuous monitoring
comes true.
EXIT
4.2.7 Alarm
<DOME>
<PRESET>
<SCAN>
<GUARD TOUR>
<PATTERN>
<PRIVACY ZONE>
<OTHER>
<ALARM >
EXIT
<ALARM>
ALARM IN
ALARM OUT
PATROL TIME
ALARM 1
ALARM 2
ALARM 3
ALARM 4
EXIT
15
OFF
NC
05S
PRESET-01
PRESET-02
PRESET-03
PRESET-04

ALARM IN: Alarm input has OFF and ON selectable.

ALARM OUT: Alarm output has NC an NO
selectable.

DWELL TIME: Its range is 05-10S.

ALARM 1: No action and preset 1-16 are selectable.

ALARM 2: No action and preset 1-16 are selectable.

ALARM 3: No action and preset 1-16 are selectable.

ALARM 4: No action and preset 1-16 are selectable.
Note: If there are several alarm inputs at the same time, the
system will respond to the alarm inputs in turn according to the
dwell time.
4.3 Camera
<CAMERA>
ZOOM LIMIT
FOCUS MODE
DIGITAL ZOOM
ZOOM SPEED
<ADV>
<AE>
EXIT
AUTO
OFF
HIGH

ZOOM LIMIT: Display the maximum zoom position,
which relates to that digital zoom is OFF or ON.

FOCUS MODE: Auto and manual are selectable.

DIGITAL
selectable.

ZOOM SPEED: Zoom speed has HIGH and LOW
selectable.

WB MODE: There are indoor, outdoor, auto, manual
selectable.

RED GAIN: It can only be adjusted under the
condition that the WB mode is manual. And its range is
000-255.

BLUE GAIN: It can only be adjusted under the
condition that the WB mode is manual. And its range is
000-255.

SHARPNESS: Its adjustable range is 0-15 grade.
ZOOM:
Digital
zoom
has
ON/OFF
4.3.1 CAM ADV
<CAM ADV>
WB MODE
RED GAIN
BLUE GAIN
SHARPNESS
BLC
WDR
AUTO
AUTO
AUTO
05
OFF
OFF
EXIT

BLC: It has ON and OFF selectable.

WDR: It has ON and OFF selectable.
4.3.2 CAM AE
<CAM AE>
AE MODE
IRIS MODE
IRIS TIME
SHUTTER
GAIN
ICR
EXIT

AUTO
AUTO
AUTO
AUTO
AUTO
DAY

IRIS TIME: Set the speed of iris varying.
SHUTTER: Set the camera shutter. There are auto
and manual shutter selectable.

GAIN: GAIN has auto and manual selectable.

ICR: It has auto, day and night selectable.
Remark:
1. Iris, shutter and gain can only be set under the condition that AE mode is manual.
2. D/N switch function can only switch automatically normally under the condition that
AE mode is auto.
3. All the above functions are available if the camera supports.
16
4.4 IR
<IR>
IR MODE
OUTPUT POWER
TESTING TIME
STANDBY POWER
STANDBY TIME
ILLUMINATION ON
IR SWITCH ZOOM
AMBIENT LIGHT
EXIT
AUTO
9
08S
8
20S
08L
05

IR MODE: It has auto, small light on, large light on,
manual and off selectable.

OUTPUT POWER: Its selectable range is 1-9
level.


TESTING TIME: Its settable range is 2-15S.
STANDBY POWER: IR power standby can be set
to 1-9 level when the dome camera is in idle time,
which can improve the life of IR lamps.

STANDBY TIME: The time interval from the no
any operation to dome camera to the effective operation to it.

ILLUMINATION ON: Its range is 0-25 level. In the IR mode of auto, when the
“ILLUMINATION ON” is lower than “AMBIENT LIGHT”, the picture turns to color
and IR lamps turn off. When “ILLUMINATION ON” is higher than ”AMBIENT LIGHT”,
likewise, the picture turns to night and IR lamps turn on.

IR SWITCH ZOOM: When zoom value reaches to the demanded setting, the IR
LEDs will auto switch from near illumination to far illumination. Zoom value options
depend on the module, 01- 10 ( 12). Default setting is 05. Eg, when the zoom value
is set to 06, the IR LEDs will auto switch from near illumination to far illumination
after the zoom value reaches to 6X or more than 6X.

AMBIENT LIGHT: This function is system data and can’t be changed. It updates
automatically for the ambient light in the range of 50 levels.
4.5 Display
<DISPLAY>
DOME ID
ZOOM
P AND T
ACT
TIME
IR
EXIT

ON
ON
ON
ON
OFF
ON

DOME ID: It displays ON or OFF.

ZOOM: It can be selected as ON or OFF.

P AND T: It can be selected as ON or OFF.


ACT: It displays the current action, such as set
preset, call preset, 360°scan. ON or OFF can be
selected.
TIME: It has ON and OFF modes.
IR: “☀” means displaying the open status of IR and can be seen at the top left corner
of screen. Open the IR display progress bar “
along with the illumination level.
”, which will be filled gradually
Remark: Display Set mainly prompts the user to note the operation that the dome camera is
running.
4.6 Time
<TIME>
DATE
2000-01-01
TIME
00:00:00
<SCHEDULE>
17
SAVE
EXIT

DATE: Set the system date.

TIME: Set the system time.

SCHEDULE:
Action: There are preset 1-8, A-B scan, 360°scan, guard tour preset, pattern, no action
selectable.
Example of Schedule:
<SCHEDULE>
START
END
ACT
00:00:00 00:00:00 NONE
00:00:00 00:00:00 NONE
00:00:00 00:00:00 NONE
00:00:00 00:00:00 NONE
00:00:00 00:00:00 NONE
00:00:00 00:00:00 NONE
00:00:00 00:00:00 NONE
00:00:00 00:00:00 NONE
SAVE
1: 8 schedules can be set. First, select the schedule needing
to be set and press the right key to enter the setting status.
2: Use the up and down keys to adjust the present value,
and press the right key to enter and come to the next
adjustment. The item being changed will blink. When it
blinks, operate the right key again to exit the editing the
schedule, while press the left key to give up operation.
3: Select the next schedule and repeat the operations
above.
4: When setting the status, press left key to exit setting.
When selecting the status, press left key to return to the previous page.
Remark: When the schedule is set, there can not be overlap part in periods of time. The
system will respond at priority to the first triggered schedule, only after which is completed, it
will respond other schedules. Please make sure there is only one schedule at some certain
period. System will return to preset 1 after completing schedule.
4.7 Language

<LANGUAGE>
LANGUAGE
EXIT
LANGUAGE: Language can be set as Chinese,
English.
ENGLISH
4.8 Reset

CAM DATA: It is used to initialize the camera and
apply to the situation of camera displaying incorrectly.

SYS DATA: It is used to initialize the system
settings, including the camera settings, but it will not
delete all the information in memory.

FACTORY DEFAULT: It is used to initialize the
settings of system and camera. After it performs, all
the information in memory will be deleted, such as
presets, pattern, etc. Please use carefully. And this
operation will take much time. Please wait patiently.
<RESET>
CAM DATA
SYS DATA
FACTORY DEFAULT
CALIBRATION
EXIT

18
15D
CALIRATION: Execute this function to make the motor of the dome to reset in a fixed
time to prevent locate inaccurately caused by external operation. Default reset time is
15D. 01 to 60 and Off are selectable.
Appendix Ⅰ Anti-lightning, Anti-surges
This product is extremely air discharge and lightning protection with TVS tube technology,
which can effectively prevent the transient lightning below voltage 6000V, surge and damages
caused by other types of pulse signals.
However, necessary protective measures should be made in the premise of ensuring
electrical safety for outdoor installation according to the actual situation :
·Signal transmission line must be at least 50 meters far away from the high-voltage
equipment or high voltage cable.
· Try to choose outdoor wiring laid down along the roof line.
· Way of sealed steel pipe buried wiring is used in the area which opened, and steel pipe
units grounded in one point. Overhead wiring is absolutely prohibited.
· In the strong thunderstorms area or areas with high induced voltage (such as high voltage
substations), measure of installation of additional high power lightning protection equipment
and lightning rod must be taken.
· Lightning protection and grounding of outdoor devices and lines must take the
lightning-protection requirements of buildings into consideration, and comply with the related
national standards and industry standards.
· System must be equipotential grounding. Grounding device must meet dual requirements
of anti-interference and electrical safety, and should not be shorted or mixed with the adjacent
lines in the strong power grid. When system is independently grounded, grounding impedance
should be less than 4Ω, and cross-sectional area of grounding conductor must be not less than
25mm2.
Fig 25
Appendix Ⅱ Clean Transparent Cover
In order to assure a clear image of dome, the under cover of dome should be cleaned regularly.
● Be careful when cleaning and hold the outer ring of under cover by hands to avoid directly
touching with it. Because the acid sweat of finger membrane may corrode the surface coating
of under cover. Hard tool scratching the under cover may lead to blurring the images of dome
so that affecting image quality.
19
● Please use a soft enough dry cloth or other alternatives to wipe internal and external surface.
● If dirt is serious, user can use a mild detergent. Any senior furniture cleaning products can be
used to clean the under cover.
Appendix Ⅲ Common Knowledge on RS-485 Bus
1. Basic Feature of RS-485bus
According to industry bus standard of RS-485, RS-485 bus is half-duplex communication bus
with the characteristic impedance of 120Ω, whose maximum load capacity is 32 payloads
(including the master device and the controlled device).
2. Mode of Connection and Terminal Resistance
2.1 Industry standard of RS485 bus requires that connection mode in a daisy chain should be
used between the devices with 120Ω terminal resistances connected at the both ends.
As shown in fig. 26 and fig. 27 is simplified connection, but the distance of part "D" shall not
beyond 7 meters.
Fig 26
2.2
Fig 27
120Ω terminal resistance is connected as shown in fig 27.
120Ω terminal resistance is available in the circuit board, which is on the power board below the
mounting bracket.
When connecting 120Ω resistance if needed, just take the mini jumper from "OFF" to "ON".
Then the 120Ω resistance is connected to the circuit. The factory default of mini jumper is in
"OFF" position.
20
Appendix Ⅳ Exception Handling
Issue
Possible Reason
Solution
After power is applied, Cable harness is improperly Verify that the orientation of the
connected
connector input
there is no action
Input power voltage is too low Verify the voltage of the input power
(self-test)
and no video image.
Power supply does not work
Change a new power supply
Self-test is normal, but Wrong communication
dome
cannot
be
settings
controlled.
Set the correct protocol, baud rate
and address of dome device
Improper connection of
Verify the polarity of the RS485
connection as per the instruction
manual
control cable (polarity)
Noise
self-testing
after Mechanical obstruction
Image is not stable
Camera module
installed correct
is
Verify and correct it
not Correct
Low power
Change the correct power supply
Low power
Check the power supply or make sure
the power input is AC 24V
Video cable is improperly Verify the connection of the video
connected.
cable
Image is blurring
Controlling the dome
is not smooth
Camera is on manual focus
Change to auto focus
The lens is dusted
Clean the lens
Power is too low
Change the AC 24V Power supply
Communication distance is
Make sure the distance is in the
too long
allowed range
RS485 cable is not properly Make the
connected.
connected.
Too many domes connected
21
RS485
is
properly
Make sure the connected dome is in
the allowed quantity
Copyright Statement
This copyright merely belongs to the manufacturer. Without permission, please don’t plagiarize
or copy the contents of this book in any form or by any means.
The company follows the policy of continuous development. Therefore, the company reserves
the right to modify or improve the products described in this manual without notice.
The content of manual is offered according to the "current state". Unless applicable law
otherwise specified, the company does not make any kind of clear or tacit reassurance about
the accuracy, reliability and contents of this manual. The company reserves the right to revise
or recoup this manual at any time without notice.
Specification
Item No.
Pick Up Device
Effective Pixels
Optics
D. ZOOM
Scanning System
Synchronization
Resolution
Min. Illumination
S/N
Video Output
Focus
IRIS Control
Lens Initialize
Day & Night
Gain Control
White Balance
BLC
DRC
AES
SSNR
22
15-CD512WI
1/4" Interline Transfer CCD
NTSC:768(H) x 494(V)/ PAL: 752(H) x 582(V)
12x, f=3.94 ~ 46.05mm
Off / On (2x ~ 16x)
2:1 Interlace
Internal
Color: 560 TV Lines, B/W: 680 TV Lines
Color: 0.2 Lux, B/W: 0.04 Lux
52 dB
1.0Vp-p/75Ω
Auto / Manual / One push
Auto, Manual
YES
Auto/ Color/ B/W (ICR ON)
Off/ Low/ Middle/ High/ Manual
ATW / AWC / Indoor / Outdoor / Manual
Off/ BLC/ HLC (Back Light Compensation)
Off/ On (Dynamic Range Compression)
1/50, 1/60, ~ 1/120,000 sec
Off / On