Viking FDSB5481D Installation guide

Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
UL
F20844 EN
C
UL
(012512)
Custom Panel Models
All Refrigerator/Freezer/
Side-by-Side/Bottom-Mount
Table of Contents
Warnings & Important Information ____________________________________________________________________3
Bottom-Mount
Dimensions and Specifications (36”) __________________________________________________________6
Cutout Dimensions (36”) ____________________________________________________________________8
Anti-Tip Dimensions (36”) ___________________________________________________________________9
Overlay Dimensions (36”) __________________________________________________________________10
Custom Grille Dimensions (36”) _____________________________________________________________11
Side-By-Side
Dimensions (42”) _________________________________________________________________________13
Dimensions (48”) ________________________________________________________________________14
Specifications (42” and 48”) ________________________________________________________________15
Cutout Dimensions (42”) __________________________________________________________________16
Anti-Tip Dimensions (42”) _________________________________________________________________17
Cutout Dimensions (48”) ___________________________________________________________________18
Anti-Tip Dimensions (48”) __________________________________________________________________19
Overlay Dimensions (42”) __________________________________________________________________20
Overlay Dimensions (48”) __________________________________________________________________21
Custom Grille Dimensions (42”) ____________________________________________________________22
Custom Grille Dimensions (48”) ____________________________________________________________23
All Refrigerator/Freezer
Dimensions & Specifications (30” and 36”) ___________________________________________________24
Cutout Dimensions (30”) ___________________________________________________________________26
Anti-Tip Dimensions (30”) __________________________________________________________________27
Cutout Dimensions (36”) ___________________________________________________________________28
Anti-Tip Dimensions (36”) __________________________________________________________________29
Dimensions (Dual 30”) _____________________________________________________________________30
Dimensions (Dual 30” and 36”) _____________________________________________________________31
Dimensions (Dual 36”) _____________________________________________________________________32
Specifications (Dual) _______________________________________________________________________33
Cutout Dimensions (Dual 30”) ______________________________________________________________34
Anti-Tip Dimensions (Dual 30”) _____________________________________________________________35
Cutout Dimensions (Dual 30” and 36”) ______________________________________________________36
Anti-Tip Dimensions (Dual 30” and 36”) _____________________________________________________37
Cutout Dimensions (Dual 36”) ______________________________________________________________38
Anti-Tip Dimensions (Dual 36”) _____________________________________________________________39
Overlay Dimensions (30” & 36”) ____________________________________________________________40
Custom Grille Dimensions (30”) _____________________________________________________________41
Custom Grille Dimensions (36”) _____________________________________________________________42
Custom Grille Dimensions (Dual 30”) ________________________________________________________43
Custom Grille Dimensions (Dual 30” and 36”) ________________________________________________44
Custom Grille Dimensions (Dual 36”) ________________________________________________________45
Cabinet Information _______________________________________________________________________________46
Custom Side Panel Dimensions _____________________________________________________________________48
Custom Panel General Information __________________________________________________________________49
Ice and Water Dispenser Bezel Removal ______________________________________________________________49
Custom Door Panel Installation – (Refrigerator or Freezer) ______________________________________________51
Ice and Water Dispenser Bezel Installation ____________________________________________________________54
Door Trim Insert ___________________________________________________________________________________55
Custom Panel Hinge Cutout ________________________________________________________________________56
Custom Grille Installation ___________________________________________________________________________56
General Information _______________________________________________________________________________58
Unpacking & Moving ______________________________________________________________________60
Installation ________________________________________________________________________________________61
Hinge Adjustment_________________________________________________________________________62
Kickplate Installation_______________________________________________________________________64
Door Stop Adjustment _____________________________________________________________________65
Water Filter Installation ____________________________________________________________________66
Water Filter System Specifications___________________________________________________________67
Final Installation __________________________________________________________________________68
Performance Checklist _____________________________________________________________________________69
Control Panels ____________________________________________________________________________________70
Service & Registration ______________________________________________________________________________72
2
IMPORTANT –
Please Read and Follow
• Make sure that incoming voltage is the same as
unit rating. An electric rating plate specifying
voltage, frequency, wattage, amperage, and
phase is attached to the product.
• To reduce the risk of fire, electrical shock, or injury
to persons, installation work and electrical wiring
must be done by a qualified technician in
accordance with all applicable codes and
standards, including fire-rated construction.
• The installer should leave these instructions with
the consumer who should retain them for local
inspector’s use and for future reference.
Your safety and the safety of others is
very important.
We have provided many important safety
messages in this manual and on your
appliance. ALWAYS read and obey all
safety messages.
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
All safety messages will be preceded
by the safety alert symbol and the word
“DANGER” or “WARNING.”
These words mean:
It is your responsibility to:
• Comply with installation specifications and
dimensions.
• Properly install unit.
• Remove any moldings or decorative panels that
prevent the unit from being serviced.
• Make sure that you have these materials (not
provided with your unit), which are necessary for
proper installation:
• 1/4” (6 mm) copper tubing with shutoff valve
• 6 – #8 x 3” (7.6 cm) wood screws (longer
screws may be required)
• 1– Saddle valve (DO NOT use self-piercing
feature of the valve)
• Assure that floor will support unit, door panels
and contents (approximately 1200 pounds
[540 kg]).
• Provide a properly grounded electrical outlet.
• Assure that location will permit appliance doors
to open a minimum of 90˚.
DANGER
Hazards or unsafe practices
which WILL result in severe personal
injury or death
WARNING
Hazards or unsafe practices
which COULD result in severe personal
injury or death
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
3
IMPORTANT–Please Read and Follow!
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local
laws, or local ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to
any significant sources of water or moisture.
• Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which
are not installed properly or do not meet the requirements below.
If
•
•
•
•
the use of a GFI is required, it should be:
Of the receptacle type (breaker type or portable type NOT recommended)
Used with permanent wiring only (temporary or portable wiring NOT recommended)
On a dedicated circuit (no other receptacles, switches or loads in the circuit)
Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT
recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard)
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water, steam, high humidity) as much as reasonably possible
4
WARNING
WARNING
ELECTRICAL SHOCK
HAZARD
TIP OVER HAZARD
Appliance is top heavy
and tips easily when not
completely installed. Keep
doors closed until appliance
is completely installed and secured per
installation instructions.
Disconnect power or turn
power disconnect switch to
OFF position before removing top grille.
Failure to do so can result in death or
electric shock.
Use two or more people to move and
install appliance. Failure to do so can
result in death or serious injury.
Most of the unit’s weight is at the top. Extra care is needed when moving the unit to prevent
tipping. Use cardboard shipping material or plywood under unit until it is installed in the
operating position to protect floor surface.
5
Dimensions
Specifications
(Bottom-Mount)
36” Bottom-Mount
(Bottom-Mount)
36” Bottom-Mount
Description
Overall width
Overall height (from bottom)
Overall depth (from rear)
3
(88 5”
.9 c
m)
3-1
(8.9 /2”
cm
)
Cutout width
Cutout height
Cutout depth
Electrical requirements
36
(91 ”
.4 c
m)
Maximum amp usage
Inlet water requirements
51
(13 -7/8
1.8 ”
cm
)
ies
varare)
t
en w
rem d
asusupplie
e
M y
( lo c
Overall interior dimensions
Refrigerator
Freezer
Total capacity
Maximum panel weight
Approximate shipping weight
d
har
all
82
23
(21 -7/8
0.5 ”
mincm)
.
84 to
1
(21 /16
3.5 ”
ma cm)
x.
-1
FDBB5361
36” (91.5 cm)
82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.
To front edge of side trim: 23-13/16” (60.5 cm)
To front of top grille: 24-3/4” (62.9 cm)
To front edge of door trim: 24” (61.0 cm)
36” (91.5 cm)
82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.
24” (61.0 cm) min.*
115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product
9.9 amps
1/4” copper tubing inlet waterline; minimum 20 psi;
maximum 120 psi
15.3 cu. ft. (434 liters)
5.1 cu. ft. (145 liters)
20.4 cu. ft. (579 liters)
Fresh food 45 lbs. (20.4 kg)
Freezer 20 lbs. (9.0 kg)
500 lbs. (227.3 kg)
*Note: Custom panel models fit flush in 25” (63.5 cm) deep cabinet openings. They can be installed in standard
24” (61.0 cm) deep openings. The door faces and top grille will protrude 3/4” (1.9 cm) into the room.
(58 /16
.6 c ”
m)
/16
-13 cm)
3
2 .5
”
(60
4”
-3/
24.9 cm)
(62
6
7
Cutout Dimensions
Anti-Tip Dimensions
(Bottom-Mount)
36” Bottom-Mount
24” )
cm
(61.0
See an
ti-tip b
oa
rd inst
a
(Bottom-Mount)
36” Bottom-Mount
Electric Outlet Location
llation
6”
(15.2
c m)
Anti-Tip Location
9”
(22.9
cm)
9”
(22.9
c m)
79
peni
ng
rd &
heig
ht
29”
(73.7 c
m)
8
(204 0-1/2”
.6
to bo cm) max
.
ttom
a
/
(213
.5 16”
anti- cm) m
t
a
op ip boa x.
r
g he d &
ight
(3.8 c
anti- ttom of
tip b
oard
84-1
enin
”
1-1/2m)
(201 -3/8”
.6
to bo cm) min
.
82
(210 -7/8”
.5
anti- cm) mi
tip b
n.
oa
o
3-1/2
(8.9 c ”
m)
nti-ti
o
p bo f
ard
73-3
(186.4/8”
cm)
Water Line Entry Area
36
7-5/
(91.5 ”
cm)
(19.4 8” 6
-3/
cm)
5/8”
(17.1 4”
(1.5
cm)
cm)
3”
(7.6
cm)
(91. 36”
5 cm
)
One mounting
2”x 4” mounting
board (3.8 cm) x 3-1/2” (8.9 cm)
One 2”x4”
board 1-1/2”
cm) x 3-1/2”
cm)24” (61.0 cm), then
Note: If1-1/2”
unit is(3.8
installed
deeper(8.9
than
Note: If unit is installed deeper than 24” (61.0 cm),
shim behind
the
mounting
board
by
the difference.
then shim behind the mounting board by the difference.
5/8
(1.5 ”
cm)
3
(9.2 -5/8”
cm)
1
(27. 0-3/4
3 cm ”
)
BottomBottom
of anti-tip
board board
is 3-7/8”
(9.8 cm)
the opening
of anti-tip
is 3-7/8”
(9.8below
cm) below
openingheight.
height.
Note:
unit must
be placed
firmly
under
anti-tipboard.
board.
Note: Top
ofTop
unitofmust
be placed
firmly
under
anti-tip
(2 .5
1
(26.70-1/2”
cm )
1” )
cm
(1.5 5/8”
cm )
p
waO
ter tiona
line l flo
ent or
ry
8
9
Overlay Dimensions
(Bottom-Mount)
Custom Grille Dimensions
36” Custom Panels
36” Custom Grille
1
s
diu
Ra )
”
m
4
c
1/ 6.24
(1.2/2”
7c
m)
35
-
(10 1/64
.59 ”
cm
)
3” m)
7
(1.2
2c
(7.6
(13 -1/4
0.2 ”
2c
(7.6
0
.6
(4
3/1
6”
)
cm
3
(7.6 ”
2c
m)
/4”
3-3 cm)
3
3
(.2 /3
4 2”
cm
)
1-1
0c
5/
(1.6 8”
cm
)
5
(1.6/8”
cm
)
32
Note: Inset shown
upside down.
-1/
4
(1.9/4”
0c
m)
.34
m)
”
cm
)
32
-3
(81 /16
. 75 ”
cm
)
2
(9.5
51
(13 -7/8
1.8 ”
cm
)
/8”
3-5 cm)
1
(1.2/2”
7c
m)
0
(9.2
3
(86 4”
.36
cm
”
(81 to n
.9 c ot
m) ch
2-1
(5.4 /8”
cm
)
)
/4”
3-3 cm)
3
(1.9/4”
0c
m)
2
(9.5
33
-1
(86 5/1
.20 6”
c
m)
”
3/4 )
(1.9
30
-2
(78 7/3
2
3
(1.9/4”
cm
)
No
t
hin e: Co
ge r n e
S e e do o r n o
pag r. Re tch
e 5 ver is fo
4 fo se r le
r cu for r ft
tou ight
t in hin
stru ge
ctio .
n s.
s 1/
diu (1.2 2”
Ra )
7c
”
m
m)
4
1/ (.64 c
(14 7/32
.10 ”
cm
)
3” m)
Reverse dimensions
for other end.
51
1
(1.2/2”
7c
m)
1c
(3.8
5-1
(.3 1/8
1
cm ”
)
9
(6.
/2”
1-1 m)
4-1
”
1/2cm)
(89 1/4”
.5 c
m)
(1.9
3
(1.9/4”
0c
m)
”
/4 )
2-38 cm
(1.
”
3/4cm)
(Bottom-Mount)
35
-
(89 1/4”
.5 c
m)
cm
1
(1.2/2”
7c
m)
/8”
3-1 cm)
3
(7.9
(1. 1/2
27 ”
cm
)
3
(86 4”
.
36
cm
)
O
l
na
io
pt
hi
m)
2c
6
”
/1
9
Note: Panel overlays must be dry, solid, straight
one-piece panels. The use of multiple panel
pieces to achieve the dimensions is not
recommended.
35
(90 -1/2
.17 ”
cm
)
r
ve
co
-1
(58 /16
.6 c ”
m)
e
ng
23
4
(1.
2
3- 2
60 5/32
cm ”
)
2
16
. 5˚
0
.0
˚
(9 .
Note: Optional hinge cover can be attached
using a strong VHB tape, countersunk wood
screws or short nails from a nail gun.
(.8 7/3
4 c 2”
m)
m)
5c
1
/4
”
3
(.6
10
11
”
7/8 m)
2c
(2.2
Custom Grille Dimensions
Dimensions
(Bottom-Mount)
(Side-By-Side)
Dual 36” Custom Grille
4-1
1
1
(1.2/2”
7c
m)
s
diu
Ra )
”
m
4
1/ (1.6.24 c
(11 /64
.27 ”
cm
)
(.3 1/8
1c ”
m)
Reverse dimensions
for other end.
3
(1.9/4”
0c
m)
/4”
3-3 cm)
(9.5
(14 /32
.04 ”
cm
)
3” m)
7
(1.2
/2”
1-1 cm)
5-1
7
”
1/2cm)
2c
(7.6
”
/4 )
2-38 cm
(1.90 cm)
0c
m)
9
(6.
1
m)
32
-3
m
4
1/ (.64 c
1.2
7
(7.6
3
(1.9/4”
0c
m)
9/16”
(1.43 cm)
cm
)
1
3/4”
(1.90 cm)
Grille support
2- 7
(7.3 /8”
0c
m)
40
(10 11/6
2.0 4”
3
3
1
(1.2/2”
7c
m)
(9.5
3-1
(8.9 /2”
cm
)
Note: This part should be
located at the center of the
grille. If desired, two per grille
can be used by dividing the
length of the grille into thirds.
66
(16 27/3
9.7 2”
8
2c
(17 70”
7.8
0c
/8”
3-1 cm)
4
(10 2”
6.7
cm
)
(2.5 ”
4c
m)
0
/4”
3-3 m)
(10 1”
4.1
cm
)
1
(10 25/6
5.1 4”
3c
m)
cm
)
(1.9/4”
0c
m)
4
cm
)
2
/8”
3-5 cm)
(9.2
3/8”
(0.38 cm)
41
-
(1.2/2”
7c
m)
(1.27 cm)
R 3/32”
(1.90 cm)
(81 /16
.75 ”
cm
)
2c
(.32 cm)
(0.09 cm)
3/4”
ad
”R )
1/2”
(1.03 cm)
1
ius ( /2”
42” Side-By-Side
1/8”
13/32”
(1.2/2”
7c
m)
1
(3.8
30
-2
(78 7/3
.34 2”
c
3” m)
3/4”
3
(1.9/4”
68
(17 -3/64
2.8 ”
3c
m)
m)
ies
varare)
t
n
e rdw
75
-1
(19 5/1
2.9 6”
cm
)
rem d ha
asu pplie
Meally su
(loc
82
(21 -7/8
0.5 ”
mincm)
.
84 to
(21 1/16
3.5 ”
ma cm)
x.
69
(17 15/1
3
(7.9
7.6 6”
4c
m)
(17 70”
7.8
0c
(1. 1/2
27 ”
cm
)
m
”
7/8cm)
2
(2.2
io
pt
O
l
na
e
ng
hi
r
ve
co
6”
3/1 )
1
3 cm
”
16 m)
9/ .42 c
7
1
(18 -1/2
1.6 ”
1c
m)
(1
2
(.8 7/3
4 c 2”
m)
(9. 5/
60 3 2
cm ”
)
˚
2 0.5
(6
4”
-3/ m)
4
2 .9 c
32
16
. 5˚
Note: Optional hinge cover can be attached
using a strong VHB tape, countersunk wood
screws or short nails from a nail gun.
20
.0
(62
4” )
1 / 35 c m
(.6
12
13
Dimensions
Specifications
(Side-By-Side)
48” Side-By-Side
42” Side-By-Side
Description
Overall width
Overall height (from bottom)
Overall depth (from rear)
4
(11 7”
9.4
cm
)
3-1
(8.9 /2”
cm
)
75
-1
(19 5/1
2.9 6”
cm
)
(Side-By-Side)
Cutout width
Cutout height
Cutout depth
Electrical requirements
4
(12 8”
1.9
cm
)
Maximum amp usage
Inlet water requirements
Overall interior dimensions
Refrigerator
Freezer
Total capacity
Maximum panel weight
Approximate shipping weight
ies
varare)
t
n
w
me ard
ure ied h
as ppl
Meally su
FDSB5421
FDSB5421D
42” (106.7 cm)
82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.
To front edge of side trim: 23-13/16” (60.5 cm)
To front of top grille: 24-3/4” (62.9 cm)
To front edge of door trim: 24” (61.0 cm)*
42” (106.7 cm)
82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.
24” (61.0 cm) min.*
115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product
9.9 amps
1/4” copper tubing inlet waterline;
1/4” copper tubing inlet waterline;
minimum 20 psi; maximum 120 psi
minimum 35 psi; maximum 120 psi
15.0 cu. ft. (425 liters)
15.0 cu. ft. (425 liters)
9.0 cu. ft. (255 liters)
8.9 cu. ft. (252 liters)
24.0 cu. ft. (680 liters)
23.9 cu. ft. (677 liters)
Fresh food 40 lbs. (18.1 kg)
Freezer 35 lbs. (15.9 kg)
525 lbs. (236.2 kg)
(loc
48” Side-By-Side
82
(21 -7/8
0.5 ”
mincm)
.
84 to
(21 1/16
3.5 ”
ma cm)
x.
Description
Overall width
Overall height (from bottom)
Overall depth (from rear)
Cutout width
Cutout height
Cutout depth
Electrical requirements
Maximum amp usage
Inlet water requirements
6”
3/1
3-1 cm)
2 0.5
(6
4”
-3/
24 cm)
.9
(62
Overall interior dimensions
Refrigerator
Freezer
Total capacity
Maximum panel weight
Approximate shipping weight
FDSB5481
FDSB5481D
48” (121.9 cm)
82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.
To front edge of side trim: 23-13/16” (60.5 cm)
To front of top grille: 24-3/4” (62.9 cm)
To front edge of door trim: 24” (61.0 cm)*
48” (121.9 cm)
82-7/8” (210.5 cm) min. to. 84-1/16” (213.5 cm) max
24” (61.0 cm) min.*
115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product
9.9 amps
1/4” copper tubing inlet waterline;
1/4” copper tubing inlet waterline;
minimum 20 psi; maximum 120 psi
minimum 35 psi; maximum 120 psi
18.5 cu. ft. (524 liters)
18.5 cu. ft. (524 liters)
9.0 cu. ft. (255 liters)
8.9 cu. ft. (252 liters)
27.5 cu. ft. (779 liters)
27.4 cu. ft. (776 liters)
Fresh food 50 lbs. (22.7 kg)
Freezer 35 lbs. (15.9 kg)
650 lbs. (292.5 kg)
*Note: Custom panel models fit flush in 25” (63.5 cm) deep cabinet openings. They can be installed in standard
24” (61.0 cm) deep openings. The door faces and top grille will protrude 3/4” (1.9 cm) into the room.
14
15
Cutout Dimensions
24” )
.0 cm
(61
Anti-Tip Dimensions
(Side-By-Side)
42” Side-By-Side
42” Side-By-Side
See an
ti-tip b
oa
rd inst
a
(Side-By-Side)
Electric Outlet Location
llation
6”
(15.2
c m)
Anti-Tip Location
9”
(22.9
cm)
9”
(22.9
c m)
79
(201 -3/8”
.6
to bo cm) min
.
82
(210 -7/8”
.5
anti- cm) mi
tip
n.
35”
(88.9 c
m)
8
(204 0-1/2”
.6
to bo cm) max
.
ttom
a
84-1
/
(213
.5 16”
anti- cm) m
t
a
op ip boa x.
r
g he d &
ight
(3.8 c
anti- ttom of
tip b
oard
open board
&
in g h
eigh
t
e n in
”
1-1/2m)
3-1/2
(8.9 c ”
m)
nti-ti
o
p bo f
ard
73-3
(186.4/8”
cm)
Water Line Entry Area
7-5/
42
(1 0 6 ”
.7 cm
)
(19.4 8” 6
-3/
cm)
5/8”
(17.1 4”
(1.5
cm)
cm)
3”
(7.6
cm)
(106 42”
.7 cm
)
5/8
(1.5 ”
cm)
3
(9.2 -5/8”
cm)
1
(27. 0-3/4
3 cm ”
)
One 2”x
4” mounting
One 2”x4” mounting board
1-1/2”
(3.8 cm) board
x 3-1/2” (8.9 cm)
1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)
Note: IfNote:
unit isIf installed
deeper
than
24” 24”
(61.0(61.0
cm),cm),
then
shim
behind
unit is installed deeper than
then
shim
the mounting board
by
the
difference.
behind the mounting board by the difference.
(2 .5
1
(26.70-1/2”
cm )
Bottom
of anti-tip
board
is 3-7/8”
(9.8(9.8
cm)cm)
below
theopening
openingheight.
height.
Bottom
of anti-tip
board
is 3-7/8”
below
Note: Top
of
unit
must
be
placed
firmly
under
anti-tip
board.
Note: Top of unit must be placed firmly under anti-tip board.
1” )
cm
(1.5 5/8”
cm )
Optional floor
water line entry
16
17
Cutout Dimensions
4”
2
cm)
(61.0
Anti-Tip Dimensions
(Side-By-Side)
48” Side-By-Side
48” Side-By-Side
See an
ti-tip b
oa
rd inst
a
(Side-By-Side)
Electric Outlet Location
llation
6”
(15.2
c m)
Anti-Tip Location
9”
(22.9
cm)
9”
(22.9
c m)
79
82
(201 -3/8”
.6
to bo cm) min
.
(210 –7/8”
.5
anti- cm) mi
tip
n.
84
r
g he d &
ight
(3.8 c
41”
(104.1
8
(204 0-1/2”
.6 c
(213 –1/16”
.5
anti- cm) m
t
a
op ip boa x.
enin
”
1-1/2m)
anti- ttom of
tip b
oard
open board
&
ing h
eigh
t
m) m
to bo
ax.
anti- ttom of
tip b
oard
cm)
3-1/2
(8.9 c ”
m)
73-3
(186.4/8”
cm)
Water Line Entry Area
4
7-5/
7-1
(120 /2”
.7 cm
)
(19.4 8” 6
-3/
cm)
5/8”
(17.1 4”
(1.5
cm)
cm)
3”
(7.6
cm)
(121 48”
.9 cm
)
5/8
(1.5 ”
cm)
3
(9.2 -5/8”
cm)
1
(27. 0-3/4
3 cm ”
)
One 2”x 4” mounting boards
1” )
cm
(2 .5
1
(26.70-1/2”
cm )
One 2”x4” mounting
board(3.8
1-1/2”
cm)(8.9
x 3-1/2”
1-1/2”
cm) x(3.8
3-1/2”
cm) (8.9 cm)
If unit
is installed
deeper
(61.0
cm),
then
shimbehind
Note: IfNote:
unit is
installed
deeper
thanthan
24” 24”
(61.0
cm),
then
shim
behindby
thethe
mounting
board by the difference.
the mounting board
difference.
Bottom
of anti-tip
board
is 3-7/8”
below
opening
height.
Bottom
of anti-tip
board
is 3-7/8”
(9.8(9.8
cm)cm)
below
the
opening
height.
Note:
unit be
must
be placed
firmly
under
anti-tip
board.
Note: Top
of Top
unitofmust
placed
firmly
under
anti-tip
board.
(1.5 5/8”
cm )
Optional floor
water line entry
18
19
Overlay Dimensions
42” Custom Panels
”
3/4 )
(1.9
cm
18
-3
(46 /16
.2 c ”
m)
”
3/4cm)
(1.9
cm
22
18
”
3/4cm)
-13
(57 /16
.9 c ”
m)
-3
(46 /16
.2 c ”
m)
(1.9
31
-1
(47 1/16
.5 c ”
m)
”
3/4cm)
(1.9
”
3/4cm)
-
cm
)
(1.9
31
10
-1
12
-
75
75
(19 -1/2
1.8 ”
cm
)
3/8”
(1.0 cm)
14-1/2”
(36.8 cm)
5/16”
(0.8 cm)
radius
12-15/16”
(32.9 cm)
-
(31 3/8”
.4 c
m)
(19 -1/2
1.8 ”
cm
)
/
(8.0 32”
cm
)
20
-
(27 1/16
.1 c ”
m)
3-5
Dispenser
Dimensions
-5
(71 /16
.9 c ”
m)
(80 5/8”
.3 c
m)
-1
12
Note: Panel overlays must be dry,
solid, straight one piece panels.
The use of multiple panel pieces to
achieve the dimensions is not
recommended.
”
3/4cm)
28
(31 3/8”
.4 c
m)
(19 -1/2
1.8 ”
cm
)
-1
(47 1/16
.5 c ”
m)
-13
(27 1/16
.1 c ”
m)
75
18
(1.9
(57 /16
.9 c ”
m)
(80 5/8”
.3 c
m)
10
48” Custom Panels
with Dispenser
-5
(71 /16
.9 ”
cm
22
18
28
”
3/4 )
(1.9
(Side-By-Side)
48” Custom Panels
42” Custom Panels
with Dispenser
”
3/4 )
(1.9
Overlay Dimensions
(Side-By-Side)
3-5
/
(8.0 32”
cm
)
75
(19 -1/2
1.8 ”
cm
)
Note: Panel overlays must be dry,
solid, straight one piece panels.
The use of multiple panel pieces to
achieve the dimensions is not
recommended.
3/8”
(1.0 cm)
14-1/2”
(36.8 cm)
5/16”
(0.8 cm)
radius
Dispenser
Dimensions
12-15/16”
(32.9 cm)
21
Custom Grille Dimensions
Custom Grille Dimensions
(Side-By-Side)
42” Custom Grille
48” Custom Grille
1
1
(1.2/2”
7c
m)
3
(1.9/4”
0c
m)
”
/4 )
2-38 cm
9
”
1/2cm)
3” m)
c
cm
)
”
1/4 )
3
cm
)
3- cm
(1.9/4”
0c
m)
2
(9.5
3
(1.9/4”
0c
m)
26
(66 3/16
.51 ”
2c
(7.6
(.
30
-2
(7 7/3
(1.9/4”
0c
m)
8.3 2”
4c
m)
3- cm
2
(9.5
32
(81 3/16
cm
)
1
(1.2/2”
7c
m)
0
(9.2
(10 40”
1.6
0c
/4”
3-3 cm)
3
(1.9/4”
0c
m)
2
39
(10 15/1
1.4 6”
4
cm
)
/8”
3-1 cm)
1
3
(7.9
(1.2/2”
7c
m)
(10 40”
1.6
0c
(1. 1/2
27 ”
cm
)
m)
(11 46”
6.8
4c
/4”
3-3 m)
2c
(9.5
m)
45
(11 15/1
/8”
3-1 cm)
6.6 6”
8c
m)
3
(7.9
(11 46”
6.8
4c
”
7/8cm)
2
(2.2
(1. 1/2
27 ”
cm
)
”
7/8cm)
2
.
2
( 2
m)
hi
l
na
io
pt
l
na
O
io
pt
O
)
cm
/8
39
-1
(5 .
3
cm ”
)
(7 .
94
)
cm
3/
8
( .9 ” R a
5c d
m) ius
)
Note: Optional hinge cover can be attached
using a strong VHB tape, countersunk wood
screws or short nails from a nail gun.
(9. 3-5/
20 8 ”
cm
)
”
”
3/8cm)
3/8cm)
9
(. 5
22
(3. 1-3/
49 8”
cm
)
”
”
/8
-1
2
(9. 3-5/
20 8
(12 -1/2
0.6 ”
5c
m
”
3/
8
( .9 ” R a
5c d
m) ius
Note: Optional hinge cover can be attached
using a strong VHB tape, countersunk wood
screws or short nails from a nail gun.
47
(3. 1-3/
49 8”
cm
)
)
r
ve
co
r
ve
co
e
ng
hi
e
ng
41
(10 -1/2
5.4 ”
1c
m
0
(9.2
/8
1
(1.2/2”
7c
m)
(9.5
m)
m)
/8”
3-5 cm)
-1
3
(1.9/4”
0c
.75 ”
cm
)
/8”
3-5 cm)
1
(1.2/2”
7c
m)
1
(1.2/2”
7c
m)
s 1/
diu (1.2 2”
Ra )
7c
”
m
m)
4
1 / 64 c
-1
3
”
3/4 )
9
(6.
1c
(3.8
(29 7/3
.28 2”
cm
)
3” m)
Reverse dimensions
for other end.
24
-2
(63 7/3
.10 2”
3
(1.9/4”
0c
m)
c
/2”
1-1 m)
5.8 4”
4c
m)
11
(.3 1/8
1c ”
m)
(.
2
(7.6
10
-1
(1 1/6
(.95
23
(5.
39
)
cm
”
Reverse dimensions
for other end.
cm
)
c
3” m)
7
(1.2
s 1/
diu (1.2 2”
Ra )
7c
”
m
m)
4
1 / 64 c
5-1
(14 7/32
.04 ”
3” m)
2
(7.6
1
(3.8
”
1/2cm)
/8
(.3 1/8
1c ”
m)
2
(7.6
(1.
1
(1.2/2”
7c
m)
3
(1.9/4”
0c
m)
-1
7
(1.2
(6.
/2 ”
1-1 cm)
4-1
(10 1/64
.60 ”
”
/4 )
2-38 cm
3
(1.
i us
ad
” Rcm)
4
1/ 6.24
(1.2/2”
7c
m)
2
i us
ad
” Rcm)
4
1/ 6.24
(Side-By-Side)
(7.
94
)
cm
Dimensions
Specifications
(All Refrigerator/Freezer)
30” All Refrigerator/Freezer
30” All Refrigerator/Freezer
Description
Overall width
Overall height (from bottom)
Overall depth (from rear)
2
(73 9”
.7 c
m)
3 -1
(8.9 /2”
cm
)
36” All Refrigerator/Freezer
30
(76 ”
.2 c
m)
75
(88 5”
.9 c
m)
3-1
(8.9 /2”
cm
)
Cutout width
Cutout height
Cutout depth
Electrical requirements
Maximum amp usage
Inlet water requirements
3
ies
varare)
t
en rdw
remlied ha
u
s
p
a p
Meally su
(All Refrigerator/Freezer)
3
(91 6”
.5 c
m)
Overall interior dimensions
total capacity
Maximum panel weight
(loc
-1
FDFB5301
15.9 cu. ft. (450 liters)
18.4 cu. ft. (522 liters)
50 lbs. (22.7 kg)
Approximate shipping weight
(19 5/1
2.9 6”
cm
)
FDRB5301
30” (76.2 cm)
82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.
To front edge of side trim: 23-13/16” (60.5 cm)
To front of top grille: 24-3/4” (62.9 cm)
To front edge of door trim: 24” (61.0 cm)
30” (76.2 cm)
82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.
24” (61.0 cm) min.*
115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product
9.1 amps
5.7 amps
1/4” copper tubing inlet
waterline; minimum 20 psi;
N/A
maximum 120 psi
425 lbs. (193.2 kg)
82
(21 -7/8
0.5 ”
mincm)
.
84 to
1
(21 /16
3.5 ”
ma cm)
x.
ies
varare)
t
en rdw
remlied ha
u
s
p
a p
Meally su
36” All Refrigerator/Freezer
Description
(loc
75
-1
(19 5/1
2.9 6”
c
82
m)
(21 -7/8
0.5 ”
mincm)
.
84 to
-15
(21 /1
3.5 6”
ma cm)
x.
6”
3/1 )
1
m
3 c
Cutout width
Cutout height
Cutout depth
Electrical requirements
Maximum amp usage
Inlet water requirements
2 .4
(60
4”
-3/
24 cm)
(62
Overall width
Overall height (from bottom)
Overall depth (from rear)
.9
Overall interior dimensions
total capacity
Maximum panel weight
6”
3/1 )
1
3 cm
2 .4
(60
4”
-3/
24.9 cm)
FDFB5361
19.2 cu. ft. (544 liters)
22.8 cu. ft. (646 liters)
60 lbs. (27.2 kg)
Approximate shipping weight
500 lbs. (227.3 kg)
*Note: Custom panel models fit flush in 25” (63.5 cm) deep cabinet openings. They can be installed in standard
24” (61.0 cm) deep openings. The door faces and top grille will protrude 3/4” (1.9 cm) into the room.
(62
24
FDRB5361
36” (91.5 cm)
82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.
To front edge of side trim: 23-13/16” (60.5 cm)
To front of top grille: 24-3/4” (62.9 cm)
To front edge of door trim: 24” (61.0 cm)
36” (91.5 cm)
82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.
24” (61.0 cm) min.*
115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product
9.5 amps
6.5 amps
1/4” copper tubing inlet
waterline; minimum 20 psi;
N/A
maximum 120 psi
25
Cutout Dimensions
Anti-Tip Dimensions
(All Refrigerator/Freezer)
30” All Refrigerator/Freezer
30” All Refrigerator/Freezer
4”
2
cm)
(61.0
See an
ti-tip b
oa
rd inst
a
(All Refrigerator/Freezer)
Electric Outlet Location
llation
6”
(15.2
c m)
Anti-Tip Location
9”
(22.9
cm)
9”
(22.9
c m)
79
(201 -3/8”
.6
to bo cm) min
.
82
(210 -7/8”
.5
r
g he d &
ight
23”
(58.4 c
m)
8
(204 0-1/2”
.6
to bo cm) max
.
ttom
a
84
enin
(3.8 c
anti- ttom of
tip b
oard
anti- cm) mi
ti
n
open p board .
&
in g h
eigh
t
(213 -1/16”
.5
anti- cm) m
t
a
op ip boa x.
”
1-1/2m)
nti-ti
o
p bo f
ard
3-1/2
(8.9 c ”
m)
73-3
(186.4/8”
cm)
Water Line Entry Area
Note: Shown for All Freezer only.
30
7-5/
(76.2 ”
cm)
(19.4 8” 6
-3/
cm)
5/8”
(17.1 4”
(1.5
cm)
cm)
3”
(7.6
cm)
(76. 30”
2 cm
)
One 2”x
4” mounting
One 2”x4” mounting board
1-1/2”
(3.8 cm) xboard
3-1/2” (8.9 cm)
1-1/2”
(3.8 cm)
3-1/2”
(8.9cm),
cm)then shim behind
Note: If unit is installed
deeper
thanx 24”
(61.0
Note: If unit is installed deeper than 24” (61.0 cm), then shim
the mounting board
by
the
difference.
behind the mounting boards by the difference.
5/8
(1.5 ”
cm)
3
(9.2 -5/8”
cm)
1
(27. 0-3/4
3 cm ”
)
10-1
(26.7
1” )
cm
(2 .5
Bottom of anti-tip board is 3-7/8” (9.8 cm) below the opening height.
Bottom of anti-tip board is 3-7/8” (9.8 cm) below opening height.
Note: Top
of unit
must
placed
firmlyfirmly
under
anti-tip
board.
Note:
Top of
unitbe
must
be placed
under
anti-tip
board.
/
cm)2” (1.5 5/8”
cm )
Optional floor
water line entry
26
27
Cutout Dimensions
24” )
.0 cm
(61
Anti-Tip Dimensions
(All Refrigerator/Freezer)
36” All Refrigerator/Freezer
36” All Refrigerator/Freezer
See an
ti-tip b
oa
rd inst
a
Electric Outlet Location
llation
6”
(15.2
c m)
Anti-Tip Location
9”
(22.9
cm)
9”
(22.9
c m)
79
(201 -3/8”
.6
to bo cm) min
.
82
(210 -7/8”
.5
anti- cm) mi
tip
n.
(3.8 c
29”
(73.7 c
m)
8
(204 0-1/2”
.6
to bo cm) max
.
ttom
a
84-1
/
(213
.5 16”
anti- cm) m
t
a
op ip boa x.
r
g he d &
ight
”
1-1/2m)
anti- ttom of
tip b
oard
open board
&
in g h
eigh
t
enin
(All Refrigerator/Freezer)
nti-ti
o
p bo f
ard
3-1/2
(8.9 c ”
m)
73-3
(186.4/8”
cm)
Water Line Entry Area
Note: Shown for All Freezer only.
36
7-5/
(91.5 ”
cm)
(19.4 8” 6
-3/
cm)
5/8”
(17.1 4”
(1.5
cm)
cm)
3”
(7.6
cm)
(91. 36”
5 cm
)
5/8
(1.5 ”
cm)
3
(9.2 -5/8”
cm)
1
(27. 0-3/4
3 cm ”
)
One 2”x 4” mounting board
1” )
cm
(2 .5
1
(26.70-1/2”
cm )
One 2”x4” mounting1-1/2”
board(3.8
1-1/2”
cm) (8.9
x 3-1/2”
cm) (3.8
x 3-1/2”
cm) (8.9 cm)
Note: IfNote:
unit isIf installed
deeper
than than
24” (61.0
cm),cm),
then
shim
behind
unit is installed
deeper
24” (61.0
then
shim
behindby
thethe
mounting
boards by the difference.
the mounting board
difference.
Bottom
of anti-tip
board
is 3-7/8”
(9.8(9.8
cm)cm)
below
theopening
openingheight.
height.
Bottom
of anti-tip
board
is 3-7/8”
below
Note:
Top of
unitbe
must
be placed
under
anti-tip
board.
Note: Top
of unit
must
placed
firmlyfirmly
under
anti-tip
board.
(1.5 5/8”
cm )
Optional floor
water line entry
28
29
Dimensions
Dimensions
(All Refrigerator/Freezer)
Dual 30” All Refrigerator/Freezer
(All Refrigerator/Freezer)
Dual 30” & 36” All Refrigerator/Freezer
2
2
3-1
(8.9 /2”
cm
)
(73 9”
.7 c
m)
3-1
(8.9 /2”
cm
)
30
(76 ”
.2 c
m)
2
(73 9”
.7 c
m)
(73 9”
.7 c
m)
3
(76 0”
.2 c
m)
3
(88 5”
.9 c
m)
3
3
(76 0”
.2 c
m)
75
-1
(91 6”
.5 c
m)
75
es
ari
t v are)
(19 5/1
2.9 6”
cm
)
ies
varare)
t
n
w
me ard
ureplied h
s
a
p
Meally su
-1
(19 5/1
2.9 6”
cm
)
en rdw
remlied ha
u
s
p
a p
Meally su
(loc
(loc
82
82
(21 -7/8
0.5 ”
mincm)
.
84 to
-15
(21 /1
3.5 6”
ma cm)
x.
(21 -7/8
0.5 ”
mincm)
.
84 to
-15
(21 /1
3.5 6”
ma cm)
x.
29
29
-
(74 1/2”
.9 c
m)
-
(74 1/2”
.9 c
m)
29
1
(2.5 ”
be
twe4 cm
en )
uni
t
-
(74 1/2”
.9 c
m)
”
/16
-13 cm)
3
2 .5
(60
4”
-3/
24.9 cm)
s
(62
30
35
be
twe4 cm
en )
uni
t
-
(90 1/2”
.2 c
m)
1
(2.5 ”
”
/16
-13 cm)
3
2 .5
(60
4”
-3/
24.9 cm)
s
(62
31
Dimensions
Specifications
(All Refrigerator/Freezer)
Dual 36” All Refrigerator/Freezer
Dual All Refrigerator/Freezer*
Description
Overall width
Overall height (from bottom)
Overall depth (from rear)
3
3-1
(8.9 /2”
cm
)
(88 5”
.9 c
m)
3
(91 6”
.5 c
m)
Cutout width
Cutout height
Cutout depth
Electrical requirements
3
(88 5”
.9 c
m)
3
(91 6”
.5 c
m)
75
Maximum amp usage
Inlet water requirements
(All Freezer only)
Overall interior dimensions
30” freezer
30” refrigerator
36” freezer
36” refrigerator
Maximum panel weight
ies
varare)
t
en rdw
remlied ha
u
s
p
a p
Meally su
-1
(19 5/1
2.9 6”
cm
)
(All Refrigerator/Freezer)
(loc
82
(21 -7/8
0.5 ”
mincm)
.
84 to
-15
(21 /1
3.5 6”
ma cm)
x.
Approximate shipping weight
(2) 30” Units
15.9
18.4
19.2
22.8
be
twe4 cm
en )
uni
t
-
s
6
3/1
3-1 cm)
”
2 0.5
(6
4”
-3/
24.9 cm)
(62
32
ft.
ft.
ft.
ft.
(450
(522
(544
(646
**Note: Custom panel models fit flush in 25” (63.5 cm) deep cabinet openings. They can be installed in standard
24” (61.0 cm) deep openings. The door faces and top grille will protrude 3/4” (1.9 cm) into the room.
-
35
cu.
cu.
cu.
cu.
*For installation of two units side-by-side, a separate grille kit accessory must be purchased.
35
(90 1/2”
.2 c
m)
(2) 36” Units
liters)
liters)
liters)
liters)
30” freezer or refrigerator 50 lbs. (22.7 kg)
36” freezer or refrigerator 60 lbs. (27.2 kg)
30” freezer or refrigerator
425 lbs. (193.2 kg)
36” freezer or refrigerator
500 lbs. (227.3 kg)
(90 1/2”
.2 c
m)
1
(2.5 ”
(1) 36” & (1) 30” Unit
60” (152.4 cm)
66” (167.6 cm)
72” (182.9 cm)
82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.
To front edge of side trim: 23-13/16” (60.5 cm)
To front of top grille: 24-3/4” (62.9 cm)
To front edge of door trim: 24” (61.0 cm)
60” (152.4 cm)
66” (167.6 cm)
72” (182.9 cm)
82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.
24” (61.0 cm) min.**
(2) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with
grounded 3-prong plug attached to product
FDFB5301 - 9.1 amps
FDRB5301 - 5.7 amps
FDFB5361 - 9.5 amps
FDRB5361 - 6.5 amps
1/4” copper tubing inlet waterline; minimum 20 psi;
maximum 120 psi
33
Cutout Dimensions
Anti-Tip Dimensions
(All Refrigerator/Freezer)
Dual 30” All Refrigerator/Freezer
See an
ti-tip b
oa
24” )
.0 cm
(61
rd inst
a
(All Refrigerator/Freezer)
Dual 30” All Refrigerator/Freezer
Electric outlet location
llation
6”
(15.2
c m)
Anti-Tip Location
9”
(22.9
cm
9”
(22.9
)
c m)
79
82
(201 -3/8”
.6
to bo cm) min
.
(210 -7/8”
.5
anti- cm) mi
tip
n.
open board
&
ing h
eigh
t
73-3/
8
anti- ttom of
tip b
oard
”
(186.4
cm
)
/
(213
. 5 16”
anti- cm) m
tip b
a
op
oa x.
enin
23”
8
(204 0-1/2”
.6
to bo cm) max
.
ttom
a
84-1
(58.4 c
m)
o
p bo f
ard
Water Line Entry Area
7-5/
3-1/2
(271. 0-3/4
3 cm ”
)
Optional floor
water line entry
34
(8.9 c ”
m)
60
(19.4 8” 6-3
/
cm)
5/8”
(17.1 4”
cm)
(1.5 c
m) 3”
(7.6
cm)
(9.23-5/8”
cm)
23”
(58.4 c
m)
Note: Cutout opening shown with All Freezer model on left.
Reverse water line entry if All Freezer model is on right.
cm)
(3.8 c
nti-ti
r
g he d &
i g ht
(152 60”
.4
”
1-1/2m)
(152. ”
4 cm
)
One 2”x4” mounting
board
per unit 1-1/2”
One 2”x
4” mounting
board(3.8
per cm)
unit x 3-1/2” (8.9 cm)
1-1/2”deeper
(3.8 cm)
x 3-1/2”
(8.9 cm)
Note: If unit is installed
than
24” (61.0
cm), then shim behind
Note: If unit is installed deeper than 24” (61.0 cm), then shim
the mountingbehind
boardthe
by mounting
the difference.
boards by the difference.
5/8”
(1.5 c
m)
1
(26.70-1/2”
c m)
(1.55/8”
cm)
1”
(2.5
cm)
Bottom of anti-tip board is 3-7/8” (9.8 cm) below the opening height.
Bottom of anti-tip board is 3-7/8” (9.8 cm) below opening height.
Note: Note:
Top ofTop
unit
must be placed firmly under anti-tip board.
of unit must be placed firmly under anti-tip board.
35
Cutout Dimensions
Anti-Tip Dimensions
(All Refrigerator/Freezer)
Dual 30” & 36” All Refrigerator/Freezer
See an
ti-tip b
oa
24” )
.0 cm
(61
rd inst
a
(All Refrigerator/Freezer)
Dual 30” & 36” All Refrigerator/Freezer
Electric Outlet Location
llation
6”
(15.2
c m)
Anti-Tip Location
9”
(22.9
cm
9”
(22.9
)
c m)
82
(210 -7/8”
.5
anti- cm) mi
tip
n.
open board
&
ing h
eigh
t
73-3/
8
79
(201 -3/8”
.6 cm
)m
to
bo
in.
anti- ttom of
tip b
oard
”
(186.4
cm
)
29”
8
84–1
(204 0-1/2”
.6
to bo cm) max
.
ttom
a
/
(213
.5 16”
anti- cm) m
tip b
a
op
oa x.
(73.7 c
m)
-1/2”
1 m)
(3.8 c
nti-ti
o
p bo f
ard
r
enin
g he d &
ight
23”
(58.4 c
m)
Water Line Entry Area
3-1/2
Note: Cutout opening shown with All Freezer model on left.
Reverse water line entry if All Freezer model is on right.
7-5/
66
(19.4 8” 6-3
/
cm)
5/8”
(17.1 4”
cm)
(1.5 c
m) 3”
(7.6
cm)
(167 66”
.6
cm)
(9.23-5/8”
c
(271. 0-3/4
3 cm ”
)
Optional floor
water line entry
36
(167. ”
6 cm
)
One 2”x 4” mounting board per unit
One 2”x4” mounting1-1/2”
board (3.8
per cm)
unit x1-1/2”
3-1/2”(3.8
(8.9cm)
cm)x 3-1/2” (8.9 cm)
Note: If Note:
unit isIfinstalled
deeperdeeper
than 24”
cm),cm),
thenthen
shim
behind
unit is installed
than(61.0
24” (61.0
shim
behindbythe
mounting
boards by the difference.
the mounting board
the
difference.
5/8”
(1.5 c
m)
(8.9 c ”
m)
m)
1
(26.70-1/2”
c m)
(1.55/8”
cm)
1”
cm)
(2.5
Bottom
of anti-tip
board
is 3-7/8”
(9.8 (9.8
cm) cm)
below
the opening
openingheight.
height.
Bottom
of anti-tip
board
is 3-7/8”
below
Note:
Topmust
of unit
be placed
anti-tip
board.
Note: Top
of unit
bemust
placed
firmly firmly
underunder
anti-tip
board.
Note: Dimensions shown for 36” All Freezer/All Refrigerator model on the left.
Note: Dimensions
shown for
36” All
Freezer/All
Refrigerator
model
Reverse mounting
boards
if units
are installed
on the right.
on the left. Reverse mounting boards if untis are installed on the right.
37
Cutout Dimensions
Anti-Tip Dimensions
(All Refrigerator/Freezer)
Dual 36” All Refrigerator/Freezer
Dual 36” All Refrigerator/Freezer
See an
ti-tip b
oa
24” )
.0 cm
(61
rd inst
a
(All Refrigerator/Freezer)
Electric Outlet Location
llation
6”
(15.2
c m)
Anti-Tip Location
9”
(22.9
cm
9”
(22.9
)
c m)
82
79
(210 -7/8”
.5
anti- cm) mi
tip
n.
open board
&
ing h
eigh
t
73-3/
8
(201 -3/8”
.6
to bo cm) min
.
anti- ttom of
tip b
oard
”
(186.4
cm
)
29”
8
(204 0-1/2”
.6
to bo cm) max
.
ttom
a
84-1
/
(213
.5 cm16”
a
nti-t
) ma
ope ip board x.
ning
heig &
ht
(73.7 c
m)
nti-ti
o
p bo f
ard
Water Line Entry Area
7-5/
3-1/2
(8.9 c ”
m)
72
(19.4 8” 6–3
/
cm)
5/8”
(17.1 4”
cm)
(1.5 c
m) 3”
(7.6
cm)
(9.23-5/8”
cm)
(271. 0-3/4
3 cm ”
)
(182. ”
9 cm
)
One board
2”x 4”per
mounting
board(3.8
percm)
unitx 3-1/2” (8.9 cm)
One 2”x4” mounting
unit 1-1/2”
1-1/2”
(3.8 cm)
x 3-1/2”
(8.9 cm),
cm) then shim behind
Note: If unit is installed
deeper
than
24” (61.0
Note: If unit is installed deeper than 24” (61.0 cm), then shim
the mountingbehind
boardthe
bymounting
the difference.
boards by the difference.
5/8”
(1.5 c
m)
1
(26.70-1/2”
c m)
(1.55/8”
c
m)
Optional floor
water line entry
38
29”
(73.7 c
m)
Note: Cutout opening shown with All Freezer model on left.
Reverse water line entry if All Freezer model is on right.
(182 72”
.9 cm
)
1/2”
1- m)
(3.8 c
1”
(2.5
cm)
Bottom of anti-tip board is 3-7/8” (9.8 cm) below the opening height.
Bottom of anti-tip board is 3-7/8” (9.8 cm) below opening height.
Note: Top
of Top
unitofmust
placed
firmly
under
anti-tip
board.
Note:
unit be
must
be placed
firmly
under
anti-tip
board.
39
Overlay Dimensions
Custom Grille Dimensions
(All Refrigerator/Freezer)
30” Custom Panels
(All Refrigerator/Freezer)
30” Custom Grille
1
”
3/4cm)
(1.9
29
s
diu
Ra )
”
m
/4 24 c
36” Custom Panels
(1.2/2”
7c
m)
1 (1.6.
-
(74 1/4”
.3 c
m)
3” m)
7
(1.2
”
3/4 )
(1.9
cm
35
(.3 1/8
1c ”
m)
-
(89 1/4”
.5 c
m)
0c
m)
1
(1.2/2”
7c
m)
75
1
(1.2/2”
7c
m)
1
(3.8
5- 1
(14 7/32
1
ius /2
ad) (1.27 ”
R
cm
4” m
)
1 / 64 c
.10 ”
cm
)
(.
24
-2
(6 7/3
2c
(7.6
3.1 2”
0c
m)
3
/4”
3-3 cm)
3
(1.9/4”
(19 -1/2
1.8 ”
cm
)
2c
(7.6
(6.
/2”
1-1 cm)
.59 ”
cm
)
3” m)
Reverse dimensions
for other end.
9
4- 1
(10 1/64
”
1/2cm)
3
(1.9/4”
0c
m)
”
/4 )
2-38 cm
(1.9/4”
0c
m)
26
(66 3/16
.51 ”
cm
)
2
(9.5
/8”
3-5 cm)
0
(9.2
2
(71 8”
.12
cm
0c
75
(19 -1/2
”
1.8
/4”
3-3 cm)
3
(1.9/4”
cm
2
m)
(9.5
27
-1
(7 5/1
0.9 6”
6c
m)
)
1
(1.2/2”
7c
)
/8”
3-1 cm)
3
(7.9
m)
(1. 1/2
27 ”
cm
)
2
(71 8”
.12
cm
2
(2.2
)
O
l
na
io
pt
e
ng
hi
”
3/8cm)
41
39
)
cm
3
cm ”
)
(.95
40
(5.
-1
(9. 3-5/
20 8
/8
Note: Optional hinge cover can be attached
using a strong VHB tape, countersunk wood
screws or short nails from a nail gun.
2
-1
/8
”
Note: Panel overlays must be dry, solid, straight
one piece panels. The use of multiple panel
pieces to achieve the dimensions is not
recommended.
3/
8
( .9 ” R a
5c d
m) ius
(3. 1-3/
49 8”
cm
)
”
29
(74 -1/2
.93 ”
cm
)
r
ve
co
Note: Hardware placement can vary depending
on single or dual installation.
”
7/8cm)
(7.
94
)
cm
Custom Grille Dimensions
Custom Grille Dimensions
(All Refrigerator/Freezer)
Dual 30” Custom Grille
36” Custom Grille
(1.2/2”
7c
m)
3
(1.9/4”
”
/4 )
2-3 cm
(.3 1/8
1c ”
m)
c
1- cm
1
(10 1/64
.
59 ”
cm
)
Reverse dimensions
for other end.
c
/4”
3-3 cm)
3
(1.9/4”
m)
m)
3
(1.9/4”
0c
m)
32
-3
(81 /16
.75 ”
cm
)
2
(9.5
m)
Reverse dimensions
for other end.
30
-2
(78 7/3
.34 2”
c
3
(1.9/4”
0c
(.3 1/8
1c ”
m)
/4”
3-3 cm)
(14 /32
.04 ”
cm
)
3” m)
2
(7.6
c
98
m)
26
-3
3/4”
3
(1.9/4”
0c
m)
1
(1.2/2”
7c
m)
1
(3.8
24
-2
(63 7/3
.01 2”
c
3” m)
(6.
/2”
1-1 cm)
5-1
7
”
1/2cm)
7
(1.2
1
ius /2
ad) (1.27 ”
R
cm
4” m
)
1/ (.64 c
(14 7/32
.10 ”
cm
)
3” m)
2
(7.6
4” m
1/ (1.6.24 c
7c
m)
(3.8
5-1
m)
1
(1.2/2”
”
/4 )
2- 3 c m
(1.90 cm)
13/32”
3
(1.9/4”
0c
m)
R 3/32”
(0.09 cm)
9/16”
(1.43 cm)
(1.90 cm)
(1.90 cm)
Grille support
2- 7
(7.3 /8”
0c
m)
34
-1
(86 1/6
.80 4”
c
m)
2
(9.5
35
-2
(89 5/6
.90 4”
c
1
(2.5 ”
4c
m)
m)
1
/8”
3-5 m)
cm
)
3
3
(1.9/4”
0c
m)
)
/4”
3-3 cm)
33
-1
(8 5/1
1
(1.2/2”
7c
/8”
3-1 cm)
(14 58”
7.3
2c
2
(9.5
/8”
3-1 cm)
(1. 1/2
27 ”
cm
)
.36
cm
)
7.1 6”
6c
m)
m)
”
7/8 m)
(14 58”
7.3
2c
2c
(2.2
O
(1. 1/2
27 ”
cm
)
m)
”
7/8cm)
2
(2.2
”
/8 m)
2-1.39 c
”
5
(
/8 m)
3-1 94 c
(9. 3-5/
20 8 ”
cm
)
(7.
”
3/8cm)
(.95
42
59
(15 -1/2
1
”
.13
c
3/
8
(.9 ” Ra
5c d
m) ius
m)
Note: To use a custom grille on a dual installation,
you must purchase the center trim kit FCTKSS.
(3. 1-3/
49 8”
cm
)
”
Note: Optional hinge cover can be attached
using a strong VHB tape, countersunk wood
screws or short nails from a nail gun.
Note: Dual units can only be made
in a left and right hand configuration.
(9. 3-5/
20 8 ”
cm
)
Note: Optional hinge cover can be attached using a
strong VHB tape, countersunk wood screws or short
nails from a nail gun.
”
3/8cm)
(.95
43
(5 .
39
)
cm
-1
3/
8
( .9 ” R a
5c d
m) ius
(3. 1-3/
49 8”
cm
)
r
ve
co
)
e
ng
hi
r
ve
co
l
na
io
pt
e
ng
hi
O
l
na
io
pt
35
(90 -1/2
.17 ”
cm
m)
57
(14 15/1
3
(7.9
3
(7.9
3
(86 4”
56
(14 -3/64
2.3 ”
6c
m)
/8
2
/4”
3-3 cm)
Note: This part should be
located at the center of the
grille. If desired, two per grille
can be used by dividing the
length of the grille into thirds.
-1
(9.5
m)
6.2 6”
0c
m)
1
54
(13 27/3
9.3 2”
0
c
(86 4”
.36
cm
3
(1.9/4”
(1.2/2”
7c
m)
0
(9.2
3
0
(9.2
/8”
3-5 cm)
2
1
(1.2/2”
7c
m)
0c
(1.2/2”
7c
m)
3/8”
(0.38 cm)
3/4”
(.
(66 /16
.80 ”
cm
)
2c
(7.6
1/2”
(1.27 cm)
(1.03 cm)
3/4”
1
ius /2
ad (1.27 ”
cm
” Rcm)
4
)
1 / 64
1/8”
(.32 cm)
”
2
(7.6
0c
8
s
diu
Ra )
(11 /64
.27 ”
cm
)
/8
3” m)
7
(1.2
9
(6.
”
1/2 )
4-1
”
1/2cm)
0c
4-1
1
1
(1.2/2”
7c
m)
1
s
diu
Ra )
”
m
4
1/ (1.6.24 c
(All Refrigerator/Freezer)
(7 .
94
)
cm
Custom Grille Dimensions
Custom Grille Dimensions
(All Refrigerator/Freezer)
Dual 30” & 36” Custom Grille
(11 /64
.27 ”
cm
)
2c
24
-2
(63 7/3
.10 2”
c
m)
3” m)
13/32”
(1.03 cm)
3
(1.9/4”
0c
m)
(1.90 cm)
Grille support
.30
cm
)
34
-1
(86 1/6
.80 4”
c
c
60
(15 27/3
4.5 2”
4
3
1
(1.2/2”
7.4 6”
8c
m)
(16 64”
2.5
6c
7c
(1. 1/2
27 ”
cm
)
m)
2-7
cm
)
2
(9.5
1
(2.5 ”
4c
m)
/8”
3-5 m)
0c
(9.2
66
16927/3
.78 2”
/4”
3-3 cm)
(17 70”
7.8
0c
2
(9.5
/8”
3-1 cm)
Note: This part should be
located at the center of the
grille. If desired, two per grille
can be used by dividing the
length of the grille into thirds.
68
(17 -3/64
2.8 ”
4c
m)
m)
69
(17 15/1
7.6 6”
4
3
(7.9
cm
)
m)
(17 70”
7.8
0c
2
(2.2
(1. 1/2
27 ”
cm
)
m
”
7/8cm)
2
(2.2
O
l
na
io
pt
l
na
hi
e
ng
hi
e
ng
(3. 1-3/
49 8”
cm
)
/8
”
3/
8
( .9 ” R a
5c d
m) ius
Note: 30” unit is on left and 36” unit is on right.
44
)
cm
/8
39
3
cm ”
)
Note: Optional hinge cover can be attached using a strong VHB tape,
countersunk wood screws or short nails from a nail gun.
(5.
-1
(9. 3-5/
20 8
”
3/8cm)
(.95
Note: Dual units can only be made
in a left and right hand configuration.
”
6
5
(16 -1/2
6.3 ”
7c
m)
r
ve
co
r
ve
co
Note: To use a custom grille on a dual
installation, you must purchase the center
trim kit FCTKSS.
Grille support
(7.3 /8”
0c
m)
40
(10 11/6
2.0 4”
4
”
7/8cm)
io
pt
O
Note: Dual units can only be made
in a left and right hand configuration.
3/4”
cm
)
(1.9/4”
0c
m)
63
(16 15/1
3
(7.9
3
(1.9/4”
0c
m)
(7.
94
)
cm
3/8”
(0.38 cm)
(1.90 cm)
(81 /16
.75 ”
cm
)
(7.6
9/16”
(1.43 cm)
(1.90 cm)
(.
32
-3
2c
R 3/32”
(0.09 cm)
71
(18 -1/2
1
”
.61
cm
3/
8
(.9 ” Ra
5c d
m) ius
)
Note: To use a custom grille on a dual
installation, you must purchase the center
trim kit FCTKSS.
(3. 1-3/
49 8”
cm
)
(9. 3-5/
20 8 ”
cm
)
Note: Optional hinge cover can be attached using a strong VHB tape,
countersunk wood screws or short nails from a nail gun.
45
(5 .
39
)
cm
”
m)
m)
-1
7c
/8”
3-1 cm)
1
(1.2/2”
7c
m)
62
6c
m)
1/2”
(1.27 cm)
13/32”
cm
)
Note: This part should be
located at the center of the
grille. If desired, two per grille
can be used by dividing the
length of the grille into thirds.
2
1
(1.2/2”
2.5
/4”
3-3 cm)
s 1/
diu (1.2 2”
Ra )
7c
”
m
m)
4
1 / 64 c
1/8”
(.32 cm)
(1.03 cm)
3/4”
30
-2
(78 7/3
.34 2”
c
3” m)
(1.90 cm)
41
(10 25/6
5.1 4”
3
(15 -3/64
7.6 ”
0c
m)
(16 64”
2
(9.5
c
1
(1.2/2”
7c
m)
1
(3.8
1
/8”
3-5 m)
/4”
3-3 cm)
2
(7.6
3/4”
3
(1.9/4”
0c
m)
”
3
3” m)
98
(6.
(2.5 ”
4c
m)
cm
)
(1.9/4”
0c
m)
3
(1.9/4”
0c
m)
m)
2
(9.5
0
(9.2
Reverse dimensions
for other end.
2- 7
(7 /8”
m)
1
(.3 1/8
1c ”
m)
3/4”
(.
/2 ”
1-1 cm)
(14 /32
.04 ”
cm
)
(0.38 cm)
35
-2
(89 5/6
.90 4”
c
(1.2/2”
7c
m)
7
(1.2
3/8”
”
/4 )
2- 3 c m
5-1
7
”
1/2cm)
9/16”
(1.43 cm)
(11 /64
.27 ”
cm
)
(1.
(0.09 cm)
(1.90 cm)
(66 /16
.51 ”
cm
)
2c
(7.6
i us
ad
” Rcm)
4
1/ 6.24
R 3/32”
3/4”
s 1/
diu (1.2 2”
Ra )
7c
”
m
m)
4
1 / 64 c
(1.27 cm)
4-1
1
1
(1.2/2”
7c
m)
/8
/4”
3-3 cm)
26
-3
7c
m)
1/2”
-1
Reverse dimensions
for other end.
1
(1.2/2”
1/8”
(.32 cm)
/8
m)
(6.
(1.90 cm)
3
(.3 1/8
1c ”
3
(7.6
98
0c
m)
1
(3.8
(14 /32
.04 ”
cm
)
3” m)
7
(1.9/4”
0c
m)
/2”
1-1 cm)
5-1
7
”
1/2cm)
(1.2
/ )
2- 3 c m
3/4”
3
(1.9/4”
-1
1 (1.6.
4”
2
s
diu
Ra )
”
/4 24 cm
Dual 36” Custom Grille
4-1
1
1
(1.2/2”
7c
m)
(All Refrigerator/Freezer)
”
3/8cm)
(.95
(7 .
94
)
cm
Cabinet Information
Cabinet Information
Custom panel models, (with 3/4” [1.9 cm], thick panels and custom handles locally supplied),
fit flush in 25” (63.5 cm) deep (countertop depth) cabinet openings with no protrusion into
room except custom handles
Custom panel models can be installed in standard 24” (61.0 cm) deep openings. However,
the door faces and top ventilation grille will protrude 3/4” (1.9 cm) into the room. This
is ideal for alignment with full overlay cabinet doors.
Top View
Top View
Flush mount cabinet doors
Wall
Wall
1/4”
(.63 cm)
space if
25” (63.5 cm)
cabinet depth
is used
24”
(63.5 cm)
countertop
depth
3/4”
(1.9 cm)
full end panel
3/4”
(61.0 cm)
standard
cabinet
depth
25”
24”
(61.0 cm)
standard
cabinet
depth
1/8”
1/8”
Flush
Top View
Wall
1/4”
(.63 cm)
space if
25” (63.5 cm)
cabinet depth
is used
3/4”
(1.9 cm)
full end panel
(63.5 cm)
1/8”
(1.9 cm) (0.3 cm)
overlay foam
panel
Door
Flush
46
(62.9 cm)
(1.9 cm) (0.3 cm)
overlay foam
Door panel
Flush
3/4”
24-3/4”
3/4”
(1.9 cm) (0.3 cm)
overlay foam
Door panel
25”
3/4”
(1.9 cm)
full end panel
47
Cabinet
door
Custom Side Panel Dimensions
Custom Panel General Information
Custom finishing options
Z-Bracket
• All installations must allow for the refrigerator
and freezer door to open a minimum of 90˚.
• For side wall or corner installation, allow for a
standard 3” (7.6 cm) cabinet filler to assure
door(s) opens 90˚.
1”
(2.5 cm)
• Panel thickness must not exceed 1” (2.5 cm)
on hinge side. Thicker panels will interfere with
door swing and clearance.
1/4”
(0.6 cm)
4”
-3/cm)
1
2
.2
(55
Note: If a custom handle is used, a wider filler
may be necessary.
3/4”
(1.9 cm)
End panel
Ice and Water Dispenser Bezel Removal
4”
-3/ )
21 cm
(55
(if required)
.2
1
2
(2182-7
0.5 /8
cm ”
to ) min
8
(21 4-1
.
3.5 /1
cm 6”
)m
ax
.*
Note: Adding 3/4”
(1.9 cm) side panels adds
an additional 3/4” (1.9 cm)
to the overall width of
the product for each
side panel used.
(2182-7
0.5 /8
cm ”
t ) min
(21 84-1o
.
3.5 /1
c m 6”
)m
ax
.*
Remove packaging material surrounding bezel.
Grasping the sliding lever, pull away from bezel.
4
3
”
24 cm)
.0
(61
Note: Requires side panel
hardware kit (SPHKDS).
Optional kickplate notch
4”
2 cm)
.0
1
(6
(Dimensions determined by cabinets)
*Note: Depending on how high leveling feet are raised, and cabinet enclosure height.
48
Remove spill tray from lower part
of bezel exposing 2 screws.
Remove screws.
49
Ice and Water Dispenser Bezel Removal
5
(if required cont.)
6
Custom Door Panel Installation
2
1
Remove handle side cabinet screws
and trim with a phillips screwdriver.
Remove mounting support.
7
8
3
x2
x13
x13
Remove 2 additional screws under
top section of bezel.
(Refrigerator or Freezer)
x2
Remove all screws from handle side door trim.
Remove two screws from top and bottom door trim.
Remove handle side door trim.
3
4
2-1/16”
(5.2 cm)
1-11/16”
(4.3 cm)
2-13/16”
(7.1 cm)
Bottom-mount
12-1/16”
(30.6 cm)
All Refrigerator/
Freezer/
Side-by-side
2-1/8”
(5.4 cm)
Back of panel
“Z” bracket
Remove bracket.
Grasping the bezel on both sides, pull away
from the door cavity.
Note: Bezel needs to be pulled from the bottom
first and then pull slightly downward to clear
the water dispensing tube.
FOL bracket
Measure and mark the first hole for each bracket.
Store bezel and spill tray in safe and secure place
until installation.
5
6
x13
x12 BTM
x13 SxS, AFAR
Attach “Z” bracket to the hinge side of custom panel.
Attach bracket to the handle side of custom panel.
50
Push custom wood panel onto door.
51
Custom Door Panel Installation
7
Custom Freezer Door Panel Installation (Bottom-Mount Only cont.)
(Refrigerator or Freezer cont.)
2
1
8
x2
x13
x2
Reinstall handle side door trim
and door trim screws.
Slide custom wood panel to the hinge side, ensuring
“Z” bracket engages the door bracket.
x16
Open freezer door. Remove door trim screws
and door trim with a phillips screwdriver.
Remove bracket.
3
9
4
2-1/16”
2-1/16”
(5.2 cm)
(5.2 cm)
1-11/16”
x13
1-11/16”
(4.3 cm)
(4.3 cm)
Back of panel
FOL bracket
x13
Reinstall cabinet trim and screws.
Measure and mark the first hole on each side of the
bracket.
Attach bracket to the custom panel.
6
5
x16
Reinstall door trim and door trim screws.
Align and slide custom wood panel onto door.
52
53
Ice and Water Dispenser Bezel Installation (if required)
2
1
Install custom wood panels per product’s
installation instructions.
Ice and Water Dispenser Bezel Installation (if required cont.)
7
Locate opening in door and position bezel.
Note: Graphics on bezel will be on top end, tilt slightly
forward to allow water tube clearance.
3
Install two screws in lower part of bezel
but DO NOT tighten all the way.
5
6
For a left hinge door, cut 5/8” x 2-3/4” in lower left corner.
Note: Steps show panel upside down and notched for left
hinge application. Mirror dimensions for right hinge door.
Position upper mounting support over holes
underneath top section of bezel.
54
Adjust and reposition bezel
as necessary. Tighten all screws securely.
Replace spill tray in lower part of bezel.
9
4
Push firmly into cavity until lower screw holes
align with mounting holes on cavity.
8
Align cube switch with sliding lever and firmly push
until sliding lever is flush with bezel.
Install Door Trim Insert
1
Use the roll of trim insert located in the drawer inside
the unit to apply to the door trim.
55
Bottom-Mount Custom Panel Hinge Cutout (if required)
1
2
Custom Grille Installation (cont.)
3
”
32 )
3/.24 cm
4
(
1
(4 . - 1 3 /
60 1 6
cm ”
)
3
5/
(1.6 8”
cm
)
2
1
3
(7.6 ”
2c
m)
For a left hinge door, cut 5/8” x 3” in lower left corner.
Note: Steps show panel upside down and notched for
left hinge application. Mirror dimensions for right hinge
door.
1
3
5/
Pull air grille assembly forward.
Measure and cut 2-1/16” diagonal in
lower left corner.
Remove 2 mounting brackets from
the grille air assembly.
5
4
6
3
(1.6 8”
cm
)
2
Cut out diagonal in lower left corner.
Final view of lower corner.
Custom Grille Installation
2
1
Remove air grille center blade.
Remove two 1/4” (0.6 cm) screws with a magnetic
extended screwdriver at least 8” (20.3 cm) long.
56
Using eight screws removed from the mounting brackets,
attach mounting brackets to the custom wood grille using
predrilled pilot holes. (See grille overlay specifications for
proper alignment and pilot hole placement.)
Insert custom air grille assembly.
7
8
Install two 1/4” (0.6 cm) screws with a magnetic
extended screwdriver at least 8” (20.3 cm) long.
Install custom air grille center blade.
57
General Information
General Information
Area Requirements
Water Supply Requirements
A 115 volt, 60-Hz, 15 amp, fused, electrical
supply is required. It is required that a separate
circuit serving only this appliance be provided.
This appliance is equipped with a power supply
cord having a 3-prong grounding plug. To
minimize possible shock hazard, the cord must be
plugged into a mating 3-prong, grounding-type
wall receptacle.
DO NOT use an extension cord.
Verify the following:
• Unit can fit into residence and can be moved
around corners and through doorways.
• Floors can support unit’s weight plus food
weight (approximately 1200 pounds [540 kg]
per unit).
• Floors underneath refrigerator are level with
surrounding finished floor.
If codes permit a separate grounding wire
to be used, it is recommended that a qualified
electrician determine that the grounding path
is adequate.
• Rear wall is solid and is able to support two
horizontally mounted 2 x 4s (included) bolted to
two wall studs. The 2 x 4 board bolt heads must
be flush with 2 x 4 to prevent obstruction.
• Remove anything attached to rear or side walls
that can obstruct unit installation.
DO NOT ground to a gas line. Check with a
qualified electrician if you are not sure if the
appliance is properly grounded. DO NOT
have a fuse in the neutral or grounding circuit.
• Cutout dimensions are accurate.
Anti-Tip Requirements
• Electrical outlet is in correct location.
The anti-tip boards should be fastened
into position prior to moving the unit into
the opening.
• Copper tubing route must be above 35˚ F
(1.7˚ C) to prevent water line from freezing.
WARNING
• DO NOT use plastic water lines from the
household plumbing to the water inlet valve
connection on the refrigeration unit.
To avoid serious illness or death,
DO NOT use unit where water is
microbiologically unsafe or of unknown
quality, without adequate disinfection
before or after the system. Systems
certified for cyst reduction may be used
on disinfected water that may contain
filterable cysts. The contaminants or
other substances removed or reduced
by this water treatment system are not
necessarily in your water.
• DO NOT use the self-piercing feature of a
saddle valve. The hole made by the piercing
lance is too small for the water flow rate
required by the ice maker.
• If saddle valve is not used, place a separate
shut-off valve in an easily accessible location
between water supply and the unit. DO NOT
install shut-off valve behind the unit.
• The installation of Viking units with a reverse
osmosis system is acceptable as long as the
water pressure remains within the allowable
PSI as stated below. It is important to note that
with many reverse osmosis systems, the pressure
starts off high, but then it decreases as the water
level of the reverse osmosis storage area drops.
This must be considered when checking the
water pressure coming into the unit.
Use only 1/4” (6 mm) copper tubing for water
line. DO NOT install copper tubing in area
where temperatures drop below 35˚ F (1.7˚ C).
Before attaching copper tubing to the unit,
flush at least 2 quarts (1.9 L) of water through
the copper tubing and into a bucket to remove
any particles in the water line.
• Water line is in correct location.
Note: Additional mounting boards may
be required if the unit does not touch
the back wall of the enclosure. To
prevent unit from tipping forward, it
must be secured in place with a solid
soffit or wood block.
• DO NOT install a refrigeration unit near a heat
source, nor in a location where the surrounding
temperature will fall below 60º F (16º C).
Electrical Requirements
It is the customer’s responsibility to:
• Contact a qualified electrical installer.
• Assure that the electrical installation is
adequate and in conformance with the National
Electrical Code, ANSI/NFPA 70-latest edition
or Canadian Electrical Code C22.1-1998 and
C22.2 No. 0-M91 (or latest edition), and all local
codes and ordinances.
• Viking Range Corporation is not responsible
for property damage due to improper
installation or water connection.
• Connect a vertical or horizontal 1/2” (1.2 cm)
to 1-1/4” (3.2 cm) COLD water line near water
area.
• Connect 1/4” (6 mm) flexible copper tubing to
household plumbing in compliance with local
codes and ordinances.
• Run water line through the floor, back, or side
wall. Tubing should lay flat on floor underneath
the unit. Clamp tubing to wall or floor.
• Length of copper tubing must reach from water
supply connection to the unit connection with an
additional length to facilitate moving the unit
out of enclosure for cleaning or service. Tubing
should be soft instead of rigid and ends should
be free of burrs.
58
• Water pressure must be greater than 20 psi and
less than 120 psi on non-dispensers and greater
than 35 psi and less than 120 psi on dispensers.
59
Installation
General Information
1
2
Tip Over Hazard
• Most of the unit’s weight is at the top. Extra
care is needed when moving the unit to
prevent tipping.
• DO NOT remove protective film until unit is in
operating position.
• All four leveling legs must make contact with
the floor to support and stabilize the full weight.
Appliance is top heavy and tips easily when not
completely installed. Keep doors closed until
appliance is completely installed and secured per
installation instructions. Use two or more people
to move and install the appliance. Failure to do
so can result in death or serious injury.
Unpacking unit
1. Remove top and bottom strap.
• DO NOT drop unit.
Place unit in front of cutout.
2. Remove top cap.
• Remove exterior shipping materials prior to
moving unit into home.
• Use two or more people to move and install
unit. Failure to follow this instruction can result
in back or other injury.
• To avoid personal injury, wear gloves when
performing any installation procedure and wear
eye protection when cutting metal straps.
3. Cut rear of carton approximately 1/4” (0.6 cm)
to 1” (2.5 cm) from right corner with a utility
knife extended 1/4” (0.6 cm).
Pull the center grille louver up
at an angle and pull out.
3
4
4. Remove carton and exterior packaging.
Save cardboard shipping material to protect
floor surface when installing unit. Remove
anti-tip board, kickplate and door trim pieces
(DF models) from rear of unit.
Moving Unit
Using an 8” magnetic nut driver,
remove the two 1/4” screws.
1
Remove grille assembly.
2
Remove shipping brackets from skid by
removing four bolts (two on each side) with a
1/2” deep-well socket wench and a pair of pliers.
Note: Tilting unit is not required to remove
shipping brackets.
Slip cart between unit and skid. Remove unit from skid.
Note: Use excess packaging to protect decorative trim;
also, verify that leveling legs are up (0” adjustment).
60
61
Hinge Adjustment
Installation (cont.)
6
5
Front of unit
10b
10a
2
2
3”
1
1
Remove four side screws and remove unit top.
3
Loosen the four hinge screws. Adjust door.
Retighten four hinge screws.
8a
7
Place unit within 3” of being flush with cabinets.
Note: To avoid cabinet damage, place cardboard
between cabinets and unit. When moving unit,
DO NOT crimp, kink or crush water supply line.
Carefully move unit until semi flush with cabinet
(depending on unit).
11
12
1
Wall
2
2x4
Refrigerator
Attach one 2 x 4 to wall stud (refer to dimensions page
for exact location).
Replace unit top and four side screws.
9
8b
Flush water line by running two quarts of water
into a bucket. Turn water off
Pull supply tubing forward under unit.
Note: DO NOT use plastic water lines.
14
13
Wall
2x4
Refrigerator
Plug in power cord to verify operation.
Note: Make sure power switch and
showroom switch are in the “On” position.
If needed, depending on cabinet and depth,
attach second 2 x 4 to first 2 x 4.
62
Connect supply tube to water valve using
a 1/2” wrench. Note: DO NOT overtighten.
Turn on water supply and check for leaks.
63
Hinge Adjustment (cont.)
Door Stop Adjustment (Side-by-Side/All Refrigerator/All Freezer)
20
16
15
21
1
1
120˚
Screw
Wall
110˚
90˚
3
2x4
Refrigerator
Open refrigerator door so door stop and
shoulder screw are accessible.
Note: Shoulder screw should be in 110˚ door opening position.
Attach positive secure self-tapping bolts
to 2 x 4 using a 22” extension.
Lift unit off rollers to desired height
and level unit using a 5/16” head wrench.
Note: DO NOT use an electric device.
Overtightening can cause damage.
2
2
Remove shoulder screw and place in 90˚
or 120˚ position.
Door Stop Adjustment (Bottom-Mount)
17
22
23
120˚
110˚
90˚
1
3
2
2
1
Verify that drain pan is installed and aligned.
Kickplate Installation
Open refrigerator door so door stop and
shoulder screw are accessible.
Note: Shoulder screw should be in 110˚ door opening position.
18
19
1
1
2
3
2
Align holes on both ends of louvered panels
and insert screws.
Using a phillips screwdriver, attach the
kickplate to the unit and adjust to desired height.
64
65
Remove shoulder screw and place
in 90˚ or 120˚ position.
Water Filter Installation
(Side-by-Side with Dispenser)
24
Water Filter System Specification and Performance Data Sheet
25
This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration of less than or
equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53.* (100% safety factors builtin for unmetered usage for health claims only.)
2
1
Locate water filter door. The door is located under
the adjustable cold zone handle.
Push upper left corner of door to release latch
and pull door downward.
27
26
1
3
2
Contaminant
Reduction
Average
Influent
NSF Specified
Challenge
Concentration
Chlorine Taste and
Odor
2.0 mg/L
2.0 mg/L + 10%
97.5%
0.05 mg/L
N/A
> 50%
J-00056501
At least 10,000
particles/mL
98.9%
143,333 pts/mL
N/A
> 85%
J-00056506
107 to 108 fibers/L;
fibers greater than
10µm in length
>99%
<1 MF/L
N/A
> 99%
J-00056511
0.010 mg/L 0.009 mg/L + 10%
89.3%
0.001 mg/L
0.003 mg/L
N/A
J-00056512
Minimum 50,000
cysts/L
99.99%
1 cyst/L
N/A
> 99.95%
J-00056513
Lead @ pH 6.5
0.153 mg/L 0.15 mg/L + 10%
99.3%
0.001 mg/L
0.010 mg/L
N/A
J-00056515
Lead @ pH 8.5
0.150 mg/L 0.15 mg/L + 10%
99.3%
0.001 mg/L
0.010 mg/L
N/A
J-00058784
Lindane
0.002 mg/L 0.002 mg/L + 10%
97.8%
0.00004 mg/L
0.0002 mg/L
N/A
J-00058969
Mercury @ pH 6.5
0.006 mg/L 0.006 mg/L + 10%
95.0%
0.0003 mg/L
0.002 mg/L
N/A
J-00058785
Mercury @ pH 8.5
0.006 mg/L 0.006 mg/L + 10%
88%
0.0007 mg/L
0.002 mg/L
N/A
J-00058783
Toxaphene
0.015 mg/L 0.015 mg/L + 10%
93.2%
0.001 mg/L
0.003 mg/L
N/A
J-00056531
98.7%
0.153 NTU
0.5 NTU
N/A
J-00058972
Nominal Particulate 13,666,667
pts/mL
Class I, >0.5 to <
1.0 µm
Asbestos
Atrazine
Cyst*
Turbidity
96 MF/L
122,500
cysts/L
10.8 NTU
Average
Max Permissible
NSF
Avg %
Product
Water
Product
Water
Reduction
Reduction
Concentrtation Concentration Requirements
11 + 1 NTU
NSF Test
Report
*Based on the use of Cryptosporidium parvum oocysts
Insert filter cartridge into circular opening
in filter housing. Rotate clockwise gently until
filter stops.Close water filter door.
Flush 3 gallons through filter before use (flush
approximately 3 minutes). If water spurts occur,
continue to run water until water runs steady.
Additional flushing may be required in areas with poor
quality water.
NOTE: Allow 1-2 minute delay in water dispersal to
allow internal water tank to fill.
Operating Specifications
Capacity:
Certified for up to 750 gallons (2,838 L); up to nine months
Pressure Requirement:
20 - 120 psi (1.4 - 8.2 bar)
Temperature:
33-100oF (0.6 - 37.8oC)
Flow rate:
0.78 gpm (2.9 l/min.)
Check for compliance with the state and local laws and regulations.
Note: While the testing was performed under standard laboratory conditions, actual performance may vary.
Must be installed and operated in accordance with manufacturer’s recommended procedures and guidelines.
Installation instructions, parts and service availability, and standard warranty are included with the product when
shipped. This drinking water system must be maintained according to manufacturer’s instruction, including replacement
of filter cartridges.
Manufactured by: 3M Purification Inc.
400 Research Parkway
Meriden, CT 06770
66
System tested and certified by NSF International
against Standard 42 for the reduction of chlorine taste
and odor, particulate Class I and Standard 53 for the
reduction of Lead, Lindane, Atrazine, Mercury,
Toxaphene, Cyst, Turbidity, and Abestos.
67
Final Installation
Performance Checklist
29
28
Replace top air grille.
Using an 8” magnetic nut driver,
replace the two 1/4” screws.
30
31
Replace the center grille louver.
Open door. The display should flash.
32
h Verify cabinet size.
h Align/square door(s).
h Verify electrical supply and water supply
(if applicable).
h Verify drain pan is properly installed and
there are no leaks on water connection.
h Install anti-tip device(s) and verify unit is
secure.
h Install kickplate.
h Remove internal packaging and labels
and wipe unit down.
h Position unit in cutout, level at desired
height and secure unit.
Installer’s information:
h Plug-in unit and verify operation.
h Connect water supply (if applicable).
• Verify icemaker fill tube is properly
inserted.
• Verify icemaker bail arm is down.
• Verify dispenser operation
(if applicable).
Press “ACTIVATE CONTROLS”
pad and close door.
Note: There is a 6 minute delay before the unit starts.
68
Installer’s name:_____________________________
Installer’s company:_________________________
Date: ________________________________________
69
Verify Operations
Verify Operations
Control Panels
Control Panels
Bottom-Mount
All Refrigerator
FREEZER
ACTIVATE
CONTROLS
FRZ
TEMP
REF
TEMP
HIGHER
CF
MAX FRZ MAX REF
LOWER
FAST COOL
SAB SHOW
REFRIGERATOR
DOOR OPEN
POWER
HIGH TEMP
FAST
COOL
MAX
REF
MAX
FRZ
ALARM
OFF
DISPLAY
OFF
Side-by-Side
FREEZER
MAX FRZ MAX REF
FAST COOL
SAB SHOW
ACTIVATE
CONTROLS
REF
TEMP
FREEZER
HIGHER
LOWER
HIGHER
LOWER
CF
MAX FRZ MAX REF
FAST COOL
SAB SHOW
REFRIGERATOR
DOOR OPEN
POWER
HIGH TEMP
FAST
COOL
MAX
REF
ALARM
OFF
DISPLAY
OFF
REFRIGERATOR
DOOR OPEN
POWER
HIGH TEMP
FAST
COOL
MAX
FRZ
ALARM
OFF
DISPLAY
OFF
All Freezer
CF
REFRIGERATOR
DOOR OPEN
POWER
HIGH TEMP
ACTIVATE
CONTROLS
FRZ
TEMP
REF
TEMP
HIGHER
LOWER
FAST
COOL
MAX
REF
MAX
FRZ
ALARM
OFF
DISPLAY
OFF
ACTIVATE
CONTROLS
FRZ
TEMP
FREEZER
CF
MAX FRZ MAX REF
FAST COOL
SAB SHOW
1. Press “Activate Controls” pad.
1. Press “Activate Controls” pad.
2. Verify unit is not in Sabbath Mode.
If in Sabbath Mode:
A. The Sabbath Mode will disable the interior lights, display (except SAB indicator, temperature and
compartment indicator) and alarm.
To exit the Sabbath Mode:
B. Press and hold “Activate Controls” and then “Display Off” for 3 seconds. (The control will beep
three times to alert the user the Sabbath Mode has been exited.)
3. Verify unit is not in Showroom Mode.
If in Showroom Mode:
A. The Showroom Mode will disable the refrigerator system but all other functions are normal. These
include lights and control. (If the refrigerator is in Showroom Mode, SHOW will be lit.)
To exit Showroom Mode:
B. Press and hold “Activate Controls”; while holding, press and hold “Higher” and “Alarm Off”
together. (The control will beep three times to alert the user that Showroom Mode has been
exited.)
4. Press “Activate Controls” then press and hold “Lower”; while holding, press and hold “Display Off”
and hold until beeps (force start compressor).
5. All models need to be set at 38° F and 0° F for the Refrigerator and Freezer respectfully - factory
setting.
70
2. Verify unit is not in Sabbath Mode.
If in Sabbath Mode:
A. The Sabbath Mode will disable the interior lights, display (except SAB indicator, temperature and
compartment indicator) and alarm.
To exit the Sabbath Mode:
B. Press and hold “Activate Controls” and then “Display Off” for 3 seconds.
(The control will beep three times to alert the user the Sabbath Mode has been exited.)
3. Verify unit is not in Showroom Mode.
If in Showroom Mode:
A. The Showroom Mode will disable the refrigerator system but all other functions are normal.
These include lights and control. (If the refrigerator is in Showroom Mode, SHOW will be lit.)
To exit Showroom Mode:
B. Press and hold “Activate Controls”; while holding, press and hold “Higher” and “Alarm Off”
together. (The control will beep three times to alert the user that Showroom Mode has been
exited.)
4.Press “Activate Controls” then press and hold “Lower”; while holding, press and hold “Display Off”
and hold until beeps (force start compressor).
5. All models need to be set at 38° F and 0° F for the Refrigerator and Freezer respectfully - factory
setting.
71
Service & Registration
Notes
Only authorized replacement parts may be used
in performing service on the appliance. DO NOT
repair or replace any part of the appliance unless
specifically recommended in the manual. All other
servicing should be referred to a qualified
technician.
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
Record the following information indicated below.
You will need it if service is ever required. The
serial number and model number for your
appliance are located on the identification plate
mounted on the bottom left side of the door
opening.
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
Model number
________________________________________________________________________________________________________________________________________________________
_________________________________________
________________________________________________________________________________________________________________________________________________________
Serial number
________________________________________________________________________________________________________________________________________________________
_________________________________________
________________________________________________________________________________________________________________________________________________________
Date of purchase
________________________________________________________________________________________________________________________________________________________
_________________________________________
Date installed
________________________________________________________________________________________________________________________________________________________
_________________________________________
________________________________________________________________________________________________________________________________________________________
Dealer's name
________________________________________________________________________________________________________________________________________________________
_________________________________________
________________________________________________________________________________________________________________________________________________________
Address
________________________________________________________________________________________________________________________________________________________
_________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________
72
73
74
75