Mitsubishi Electric PEA-RP125 Installation manual

Air-Conditioners
PEAD-RP35,50,60,71,100,125,140JAQ
PEAD-RP35,50,60,71,100,125,140JALQ
INSTALLATION MANUAL
FOR INSTALLER
For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner
unit.
INSTALLATIONSHANDBUCH
FÜR INSTALLATEURE
Zum sicheren und ordnungsgemäßen Gebrauch der Klimaanlage das Installationshandbuch gründlich
durchlesen.
MANUEL D’INSTALLATION
POUR L’INSTALLATEUR
MANUAL DE INSTALACIÓN
PARA EL INSTALADOR
MANUALE DI INSTALLAZIONE
PER L’INSTALLATORE
Veuillez lire le manuel d’installation en entier avant d’installer ce climatiseur pour éviter tout accident et vous
assurer d’une utilisation correcte.
Para un uso seguro y correcto, lea detalladamente este manual de instalación antes de montar la unidad de
aire acondicionado.
Per un uso sicuro e corretto, leggere attentamente questo manuale di installazione prima di installare il condizionatore
d’aria.
INSTALLATIEHANDLEIDING
VOOR DE INSTALLATEUR
Voor een veilig en juist gebruik moet u deze installatiehandleiding grondig doorlezen voordat u de airconditioner
installeert.
INSTALLATIONSMANUAL
FÖR INSTALLATÖREN
Läs denna installationsmanual noga för säkert och korrekt bruk innan luftkonditioneringen installeras.
INSTALLATIONSMANUAL
TIL INSTALLATØREN
Læs venligst denne installationsmanual grundigt, før De installerer airconditionanlægget, af hensyn til sikker og
korrekt anvendelse.
MANUAL DE INSTALAÇÃO
PARA O INSTALADOR
Para segurança e utilização correctas, leia atentamente este manual de instalação antes de instalar a unidade
de ar condicionado.
E°XEIPI¢IO O¢H°IøN E°KATA™TA™H™ °π∞ ∞À∆√¡ ¶√À ∫∞¡∂π ∆∏¡ ∂°∫∞∆∞™∆∞™∏
°È· ·ÛÊ¿ÏÂÈ· Î·È ÛˆÛÙ‹ ¯Ú‹ÛË, ·Ú·Î·Ï›ÛÙ ‰È·‚¿ÛÂÙ ÚÔÛ¯ÙÈο ·˘Ùfi ÙÔ ÂÁ¯ÂÈÚ›‰ÈÔ ÂÁηٿÛÙ·Û˘
ÚÈÓ ·Ú¯›ÛÂÙ ÙËÓ ÂÁηٿÛÙ·ÛË Ù˘ ÌÔÓ¿‰·˜ ÎÏÈÌ·ÙÈÛÌÔ‡.
РУКОВОДСТВО ПО УСТАНОВКЕ
MONTÖR ‹Ç‹N
Emniyetli ve do¤ru biçimde nas›l kullan›laca¤›n› ö¤renmek için lütfen klima cihaz›n› monte etmeden önce bu
elkitab›n› dikkatle okuyunuz.
00a_KB79U749H01_Cover.p65
1
Deutsch
Français
Español
Italiano
Nederlands
Svenska
Dansk
Português
∂ÏÏËÓÈο
ДЛЯ УСТАНОВИТЕЛЯ
Для осторожного и правильного использования прибора необходимо тщательно ознакомиться с данным
руководством по установке до выполнения установки кондиционера.
MONTAJ ELK‹TABI
English
10.10.14, 9:13
Русский
Türkçe
3
3.1
[Fig. 3-1]
50~150
C
A
B
49
625
4
450
23
450
C
B
A
D
100
20
D
2
1
C
A
B
C
D
E
F
G
250
3
F
Access door
1 600 mm or more
Electrical parts box
2 100 mm or more
Air inlet
3 10 mm or more
Air outlet
4 300 mm or more
Ceiling surface
Service space (viewed from the side)
Service space (viewed from the direction of arrow)
E
A
(mm)
E
777
Model
PEAD-RP35, 50
PEAD-RP60, 71
PEAD-RP100, 125
PEAD-RP140
G
4
A
900
1100
1400
1600
B
954
1154
1454
1654
C
1000
1200
1500
1700
D
860
1060
1360
1560
E
1000
1200
1500
1700
4.1
[Fig. 4-1]
L
Z
W
X
Y
5
A Center of gravity
A
5.1
[Fig. 5-1]
5.2
[Fig. 5-2]
[Fig. 5-3]
C
D
A
B
A
D
C
E
A Unit body
B Lifting machine
C Nuts (field supply)
D Washers (accessory)
E M10 hanging bolt (field supply)
A Indoor unit’s bottom surface
2
00b_KB79U749H01_Illust.p65
2
10.10.14, 9:13
6
6.1
[Fig. 6-1]
øB
a
øA
Model
PEAD-RP35, 50
PEAD-RP60, 71, 100, 125, 140
b
A
ø12.7
ø15.88
B
ø6.35
ø9.52
a Indoor unit
b Outdoor unit
6.2
[Fig. 6-3]
[Fig. 6-4]
b
a
[Fig. 6-5]
c
90°
d
e
b
a
f
a
c
b
d
a Copper tubes
b Good
c No good
d Tilted
a Burr
b Copper tube/pipe
e Uneven
f Burred
[Fig. 6-6]
c Spare reamer
d Pipe cutter
a Flare nut
b Copper tube
6.3
[Fig. 6-7]
a
A
a
e
d
e
f
g
h
b
d
b
c
[Fig. 6-8]
b
c
c
i
a Flaring tool
b Die
c Copper tube
d Flare nut
e Yoke
a Smooth all around
b Inside is shining without
any scratches
c Even length all around
d Too much
e Tilted
f Scratch on
flared plane
g Cracked
h Uneven
i Bad examples
[Fig. 6-9]
A
J
H
B
N
I
C
O
D
20
F
J
H
20
O
20
E
20
N
G
L
K
A Pipe cover (small) (accessory)
B Caution:
Pull out the thermal insulation on the refrigerant piping at the
site, insert the flare nut to flare the end, and replace the insulation in its original position.
Take care to ensure that condensation does not form on exposed copper piping.
C Liquid end of refrigerant piping
D
E
F
G
H
I
J
K
Gas end of refrigerant piping
Site refrigerant piping
Main body
Pipe cover (large) (accessory)
Thermal insulation (field supply)
Pull
Flare nut
Return to original position
L
M
N
O
Ensure that there is no gap here
Plate on main body
Band (accessory)
Ensure that there is no gap here. Place join upwards.
3
00b_KB79U749H01_Illust.p65
3
10.10.14, 9:13
6
6.5
[Fig. 6-10]
Max. 20m
1.5-2m
Max. 300mm
C
N
B
A
B
J
F
K
L
B
D
O
M
D
E
F
F
D
F
G
I
H
Correct piping
Wrong piping
A Insulation (9 mm or more)
B Downward slope (1/100 or more)
C Support metal
K Air bleeder
L Raised
M Odor trap
Grouped piping
D O. D. ø32 PVC TUBE
E Make it as large as possible. About 10 cm.
F Indoor unit
G Make the piping size large for grouped piping.
H Downward slope (1/100 or more)
I O. D. ø38 PVC TUBE for grouped piping.
(9 mm or more insulation)
PEAD-RP·JALQ model
J Up to 700 mm
N Drain hose (accessory)
O Horizontal or slightly upgradient
[Fig. 6-12]
[Fig. 6-11]
I
F
E
A
F
E
A
B
A
B
C
D
E
F
G
H
I
35
32
25
C
D
D
G
H
Indoor unit
Tie band (accessory)
Visible part
Insertion margin
Drain hose (accessory)
Drain pipe (O.D. ø32 PVC TUBE, field supply)
Insulating material (field supply)
Tie band (accessory)
To be gap free. The joint section of the insulation material meet must be at the top.
A
B
C
D
E
F
G
5
25
C
D
A
B
C
D
F
A
B
C
D
E
F
Insert pump's end 2 to 4 cm.
Remove the water supply port.
About 2500 cc
Water
Filling port
Screw
4
00b_KB79U749H01_Illust.p65
4
B
Indoor unit
Tie band (accessory)
Band fixing part
Insertion margin
Drain hose (accessory)
Drain pipe (O.D. ø32 PVC TUBE, field supply)
Insulating material (field supply)
[Fig. 6-13]
E
G
10.10.14, 9:13
7
7.1
[Fig. 7-2]
[Fig. 7-1]
<A> In case of rear inlet
A Duct
B Air inlet
C Access door
D Canvas duct
E Ceiling surface
F Air outlet
G Leave distance
D
A
A
C
E
F
B
A
enough to prevent short cycle
G
B
<B> In case of bottom inlet
D
A
A
C
[Fig. 7-4]
E
C
A Filter
B Bottom plate
F
B
G
[Fig. 7-3]
D
8
8.1
[Fig. 8-1]
[Fig. 8-2]
D
A
B
C
G
A
G
G
S1
S1
S1
S1
S1
S2
S2
S2
S2
S2
S2
S2
S3
S3
S3
S3
S3
S3
S3
1
2
1
2
1
2
1
2
E
1
2
F
Outdoor unit power supply
Earth leakage breaker
Wiring circuit breaker or isolating switch
Outdoor unit
Indoor unit/outdoor unit connecting cords
Remote controller (option)
Indoor unit
A
B
C
D
E
F
G
[Fig. 8-3]
Outdoor unit power supply
Earth leakage breaker
Wiring circuit breaker or isolating switch
Outdoor unit
Indoor unit/outdoor unit connecting cords
Remote controller (option)
Indoor unit
[Fig. 8-4]
B
C
D
G
D
G
G
G
G
L
N
L
N
L
N
L
N
L
N
L
N
L
N
S1
S2
S3
S1
S2
S3
S1
S2
S3
S1
S2
S3
1
2
1
2
1
2
1
2
J
S1
S2
S3
B
C
H
A
B
E
Outdoor unit power supply
Earth leakage breaker
Wiring circuit breaker or isolating switch
Outdoor unit
Indoor unit/outdoor unit connecting cords
Remote controller (option)
Indoor unit
Option
Indoor unit power supply
C
S1
S2
S3
S1
S2
S3
F
A
B
C
D
E
F
G
H
J
C
G
S1
F
A
B
G
L
N
S1
E
A
B
C
D
E
F
G
D
L
N
1
2
J
B
C
E
F
A
B
C
D
E
F
G
H
J
H
Outdoor unit power supply
Earth leakage breaker
Wiring circuit breaker or isolating switch
Outdoor unit
Indoor unit/outdoor unit connecting cords
Remote controller (option)
Indoor unit
Option
Indoor unit power supply
5
00b_KB79U749H01_Illust.p65
5
10.10.14, 9:13
8
8.2
[Fig. 8-2-1]
[Fig. 8-2-2]
D
B
A Screw holding cover (1pc)
B Cover
A
C
E
[Fig. 8-2-3]
[Fig. 8-2-4]
J
C Terminal box
D Knockout hole
E Remove
K
G
I
F
H
F Use PG bushing to keep the weight of the cable and external force from being applied to
the power supply terminal connector. Use a cable tie to secure the cable.
G Power source wiring
H Use ordinary bushing
I Transmission wiring
J Terminal block for power source and indoor transmission
K Terminal block for remote controller
6
00b_KB79U749H01_Illust.p65
6
10.10.14, 9:13
8
8.2
[Fig. 8-3]
A Indoor terminal block
1 2
2
B Earth wire (green/yellow)
4
5
C Indoor/outdoor unit
connecting wire
3-core 1.5 mm2 or
more
1
6
3
D Outdoor terminal block
L N
7
A Indoor terminal block
B Earth wire (green/yellow)
C Indoor/outdoor unit connecting wire 3core 1.5 mm2 or more
4 Always install an earth wire (1-core 1.5 mm2)
longer than other cables
5 Remote controller cable
Wire No × size (mm2) : Cable 2C × 0.3
D Outdoor terminal block
E Power supply cord : 2.0 mm2 or more
1 Connecting cable
Cable 3-core 1.5 mm2, in conformity
with Design 245 IEC 57.
2 Indoor terminal block
3 Outdoor terminal block
This wire accessory of remote controller
(wire length : 10m, non-polar. Max. 500m)
6 Wired remote controller (option)
7 Power supply cord
Cable 3-core 2.0 mm2 or more, in conformity with Design 245 IEC 57.
E Power supply cord : 2.0 mm2 or more
8.3
[Fig. 8-4]
B
30
A
30
83.5
30
A Remote controller profile
B Required clearances surrounding the remote controller
C Installation pitch
120
C
46
[Fig. 8-5]
A
B
D
C
B-1.
B-2.
E
F
I
H
G
H
I
J
I
H
A For installation in the switch box:
B For direct installation on the wall select one of the following:
• Prepare a hole through the wall to pass the remote controller cord (in order to run the remote controller cord from
the back), then seal the hole with putty.
• Run the remote controller cord through the cut-out upper case, then seal the cut-out notch with putty similarly as
above.
C
D
E
F
G
H
I
J
Wall
Conduit
Lock nut
Bushing
Switch box
Remote controller cord
Seal with putty
Wood screw
[Fig. 8-6]
A
A To the terminal block on the indoor unit
B TB6 (No polarity)
AB
TB6
B
7
00b_KB79U749H01_Illust.p65
7
10.10.14, 9:13
8
8.4
[Fig. 8-7]
Standard 1:1
Indoor/outdoor wiring
OC(00)
A
Signal receiving unit wiring
B
TB1
A
B
C
D
TB4
IC
CN90
C
1
Outdoor unit
Refrigerant address
Indoor unit
Signal receiving unit
D
[Fig. 8-8]
A
F
B
A
B
C
D
E
F
G
H
E
G
C
D
Signal receiving unit external
Center of Switch box
Switch box
Installation pitch
6.5 mm (1/4 inch)
70 mm (2 - 3/4 inch)
83.5 ± 0.4 mm (3 - 9/32 inch)
Protrusion (pillar, etc)
H
[Fig. 8-9]
Ceiling cassette type, Ceiling concealed type
A
Indoor unit
B
A Remote controller wire
B Hole (drill a hole on the ceiling to pass the remote controller wire.)
C Signal Receiving Unit
C
[Fig. 8-10]
B
A
A Fix tightly with tape.
B Remote controller wire
C Order wire
C
[Fig. 8-11]
When installing directly on the wall
When using the switch box
B
A
H
C
Wall
D
E
J
F
G
A
B
C
D
150 mm (5 - 15/16 inch)
Remote controller wire
Wiring pipe
Locknut
E Bushing
F Switch box
G Seal around here with putty
H Seal around here with putty
I Remote controller wire
J Seal around here with putty
8
00b_KB79U749H01_Illust.p65
8
I
10.10.14, 9:13
8
8.4
[Fig. 8-12]
Insert the minus screwdriver toward the
arrow pointed and wrench it to remove the
cover.
A flat screwdriver whose width of blade is
between 4 and 7mm (5/32 - 9/32inch)
must be used.
[Fig. 8-13]
C
A
D
B
A
B
C
D
Thin-wall portion
Bottom case
Remote controller wire
Conducting wire
[Fig. 8-14]
A
A Screw (M4 x 30)
* When installing the lower case directly on the wall or the ceiling,
use wood screws.
[Fig. 8-15]
1
1
A
1 Hang the cover to the upper hooks (2 places).
2 Mount the cover to the lower case
A Cross-section of upper hooks
2
9
00b_KB79U749H01_Illust.p65
9
10.10.14, 9:13
8
8.4
[Fig. 8-16]
JP1
JP2
JP3
JP41
JP42
CN32
SW1
CN3C
CN105
CN41
SW2
OFF
CN51
ON
CN2A
SWE
CN22
CN90
CNXB2
CN4F
CN44
CN20
CN2L
CNXA2
CNXC2
A
<Indoor controller board>
[Fig. 8-18]
[Fig. 8-17]
IC
IC
IC
IC
IC
IC
IC
IC
Pair number: 0
Pair number: 1
Pair number: 2
Pair number: 3
Pair number: 0
Pair number: 0
Pair number: 0
Pair number: 0
CN90
CN90
Pair number: 0
CN90
Pair number: 1
Pair number: 2
CN90
CN90
CN90
Pair number: 3
Pair number: 0
[Fig. 8-19]
IC
IC
CN90
CN90
Pair number: 0
Pair number: 0
Pair number: 0
Pair number: 0
[Fig. 8-20]
A
CHECK
ON/OFF
TEMP
3
MODE
FAN
AUTO STOP
VANE
AUTO START
CHECK LOUVER
TEST RUN
2,4
SET
h
min
RESET
CLOCK
10
00b_KB79U749H01_Illust.p65
10
10.10.14, 9:13
CN90
CN90
8
8.5
[Fig. 8-21]
2
3 4
4
1
TEMP.
F
E
G
MENU
BACK
PAR-21MAA
MONITOR/SET
ON/OFF
ON/OFF
1
A
FILTER
DAY
CLOCK
2
CHECK TEST
OPERATION
B
CLEAR
1
C
D
[Fig.8-22]
1
2
CHECK
1
⁄
2
⁄
3
⁄
4
⁄
Mode number
Setting number
Refrigerant address
Unit number
A
B
C
D
E
F
G
Filter button (<Enter> button)
TEST button
Set Time button
Timer On/Off button (Set Day button)
Mode selection button
Set temperature button
Timer Menu button (Monitor/Set button)
CHECK
CHECK
ON/OFF
TEMP
D
E
3
C
MODE
F
FAN
AUTO STOP
VANE
AUTO START
CHECK LOUVER
TEST RUN
SET
h
4
CHECK
CHECK
Hour button
Minute button
TEMP button
TEMP button
ON/OFF button
CHECK button
A
B
min
RESET
A
B
C
D
E
F
CLOCK
9
9.2
F E
D B
B
[Fig. 9-1]
ED
[Fig. 9-2]
C
TEST RUN
COOL, HEAT
°C
°C
SIMPLE
TEMP.
MENU
BACK
MONITOR/SET
ON/OFF
A
MENU
CHECK TEST
OPERATION
BACK
CLEAR
PAR-21MAA
HG
A ON/OFF button
B Test run display
C Indoor temperature liquid line
temperature display
D ON/OFF lamp
E Power display
SIMPLE
TEMP.
C
FILTER
DAY
CLOCK
PAR-21MAA
°C
°C
ON/OFF
MONITOR/SET
ON/OFF
ON/OFF
FILTER
DAY
CLOCK
CHECK TEST
OPERATION
I M
CLEAR
A
F Error code display
Test run remaining time display
G Set temperature button
H Mode selection button
I Fan speed button
M TEST button
CHECK button
Refrigerant address
TEMP. button
IC: Indoor unit
OC: Outdoor unit
E Check code
A
B
C
D
9.3
TEST RUN
[Fig. 9-3]
ON/OFF
B
A
MODE
TEMP
FAN
AUTO STOP
VANE
AUTO START
CHECK LOUVER
TEST RUN
SET
h
C
D
A
B
C
D
TEST RUN button
MODE button
FAN button
VANE button
min
RESET
CLOCK
11
00b_KB79U749H01_Illust.p65
11
10.10.14, 9:14
10
10.1
[Fig. 10-1]
B
E
A
C
D
F
M
G
L
K
H
I
J
A
B
C
D
E
F
G
Indoor unit
Union
Liquid pipe
Gas pipe
Stop valve
Outdoor unit
Refrigerant gas cylinder operating valve
H Refrigerant gas cylinder for R410A with
siphon
I Refrigerant (liquid)
J Electronic scale for refrigerant charging
K Charge hose (for R410A)
L Gauge manifold valve (for R410A)
M Service port
12
00b_KB79U749H01_Illust.p65
12
10.10.14, 9:14
Contents
1.
2.
3.
4.
5.
Safety precautions .................................................................................
Selecting the installation location ...........................................................
Selecting an installation site & Accessories ...........................................
Fixing hanging bolts ...............................................................................
Installing the unit ....................................................................................
13
13
14
14
14
6.
7.
8.
9.
10.
Refrigerant piping work ..........................................................................
Duct work ...............................................................................................
Electrical work ........................................................................................
Test run ..................................................................................................
Maintenance ..........................................................................................
15
17
18
22
24
This Installation Manual describes only for the indoor unit and the connected outdoor unit of PUHZ series.
If the connected outdoor unit is MXZ series, refer to the Installation Manual for MXZ series.
Note: The phrase “Wired remote controller” in this installation manual refers only to the PAR-21MAA. If you need any information for THE PAR-30MAA, please refer to
either the installation manual or initial setting manual which are included in PAR-30MAA box.
1. Safety precautions
•
Please report to or take consent by the supply authority before connection
to the system.
• Be sure to read “The following should always be observed for safety” before
installing the air conditioner.
• Be sure to observe the cautions specified here as they include important
items related to safety.
• The indications and meanings are as follows.
Warning:
Could lead to death, serious injury, etc.
Caution:
Could lead to serious injury in particular environments when operated incorrectly.
• After reading this manual, be sure to keep it together with the instruction
manual in a handy place on the customer’s site.
Symbols put on the unit
: Indicates an action that must be avoided.
: Indicates that important instructions must be followed.
: Indicates a part which must be grounded.
: Indicates that caution should be taken with rotating parts.
: Indicates that the main switch must be turned off before servicing.
: Beware of electric shock.
: Beware of hot surface.
Warning:
Carefully read the labels affixed to the main unit.
Warning:
• Do not install it by yourself (customer).
Incomplete installation could cause injury due to fire, electric shock, the unit
falling or leakage of water. Consult the dealer from whom you purchased the
unit or special installer.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Install the unit securely in a place which can bear the weight of the unit.
When installed in an insufficient strong place, the unit could fall causing injured.
• Use the specified wires to connect the indoor and outdoor units securely and
attach the wires firmly to the terminal board connecting sections so the stress
of the wires is not applied to the sections.
Incomplete connecting and fixing could cause fire.
• Do not use intermediate connection of the power cord or the extension cord
and do not connect many devices to one AC outlet.
It could cause a fire or an electric shock due to defective contact, defective
insulation, exceeding the permissible current, etc.
• Check that the refrigerant gas does not leak after installation has completed.
• Perform the installation securely referring to the installation manual.
Incomplete installation could cause a personal injury due to fire, electric shock,
the unit falling or leakage of water.
• Perform electrical work according to the installation manual and be sure to
use an exclusive circuit.
If the capacity of the power circuit is insufficient or there is incomplete electrical work, it could result in a fire or an electric shock.
• If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
• Attach the electrical part cover to the indoor unit and the service panel to the
outdoor unit securely.
If the electrical part cover in the indoor unit and/or the service panel in the
outdoor unit are not attached securely, it could result in a fire or an electric
shock due to dust, water, etc.
• Be sure to use the part provided or specified parts for the installation work.
The use of defective parts could cause an injury or leakage of water due to a
fire, an electric shock, the unit falling, etc.
• Ventilate the room if refrigerant leaks during operation.
If the refrigerant comes in contact with a flame, poisonous gases will be released.
• Children should be supervised to ensure that they do not play with the appliance.
Caution:
• Perform grounding.
Do not connect the ground wire to a gas pipe, water pipe arrester or telephone
ground wire. Defective grounding could cause an electric shock.
• Do not install the unit in a place where an inflammable gas leaks.
If gas leaks and accumulates in the area surrounding the unit, it could cause
an explosion.
• Install a ground leakage breaker depending on the installation place (where it
is humid).
If a ground leakage breaker is not installed, it could cause an electric shock.
• Perform the drainage/piping work securely according to the installation
manual.
If there is a defect in the drainage/piping work, water could drop from the unit
and household goods could be wet and damaged.
• Fasten a flare nut with a torque wrench as specified in this manual.
When fastened too tight, a flare nut may broken after a long period and cause
a leakage of refrigerant.
2. Selecting the installation location
2.1. Indoor unit
•
•
•
•
Where airflow is not blocked.
Where cool air spreads over the entire room.
Where it is not exposed to direct sunshine.
At a distance 1 m or more away from your TV and radio (to prevent picture from
being distorted or noise from being generated).
2.2. Outdoor unit
Warning:
Mount the indoor unit into a ceiling strong enough to withstand the weight of
the unit.
• Install the unit horizontally.
•
•
•
•
•
Where it is not exposed to strong wind.
Where airflow is good and dustless.
Where it is not exposed to rain and direct sunshine.
Where neighbours are not annoyed by operation sound or hot air.
Where rigid wall or support is available to prevent the increase of operation sound
or vibration.
• Where there is no risk of combustible gas leakage.
• When installing the unit at a high level, be sure to fix the unit legs.
• Where it is at least 3 m away from the antenna of TV set or radio. (Otherwise,
images would be disturbed or noise would be generated.)
01_KB79U749H01_GB.p65
• In a place as far away as possible from fluorescent and incandescent lights (so the
infrared remote control can operate the air conditioner normally).
• Where the air filter can be removed and replaced easily.
13
Caution:
Avoid the following places for installation where air conditioner trouble is liable
to occur.
• Where there is too much machine oil.
• Salty environment as seaside areas.
• Hot-spring areas.
• Where sulfide gas exists.
• Other special atmospheric areas.
13
10.10.14, 9:14
3. Selecting an installation site & Accessories
• Select a site with sturdy fixed surface sufficiently durable against the weight of unit.
• Before installing unit, the routing to carry in unit to the installation site should be
determined.
• Select a site where the unit is not affected by entering air.
• Select a site where the flow of supply and return air is not blocked.
• Select a site where refrigerant piping can easily be led to the outside.
• Select a site which allows the supply air to be distributed fully in room.
• Do not install unit at a site with oil splashing or steam in much quantity.
• Do not install unit at a site where combustible gas may generate, flow in, stagnate
or leak.
• Do not install unit at a site where equipment generating high frequency waves (a
high frequency wave welder for example) is provided.
• Do not install unit at a site where fire detector is located at the supply air side. (Fire
detector may operate erroneously due to the heated air supplied during heating
operation.)
• When special chemical product may scatter around such as site chemical plants
and hospitals, full investigation is required before installing unit. (The plastic components may be damaged depending on the chemical product applied.)
• If the unit is run for long hours when the air above the ceiling is at high temperature/
high humidity (due point above 26 °C), due condensation may be produced in the
indoor unit. When operating the units in this condition, add insulation material (1020 mm) to the entire surface of the indoor unit to avoid due condensation.
Warning:
The unit must be securely installed on a structure that can sustain its weight. If
the unit is mounted on an unstable structure, it may fall down causing injuries.
3.2. Securing installation and service space
• Select the optimum direction of supply airflow according to the configuration of the
room and the installation position.
• As the piping and wiring are connected at the bottom and side surfaces, and the
maintenance is made at the same surfaces, allow a proper space properly. For the
efficient suspension work and safety, provide a space as much as possible.
3.3. Indoor unit accessories
The unit is provided with the following accessories:
No.
1
2
3
4
5
6
Name
Pipe cover (for refrigerant piping joint) Small diameter
Pipe cover (for refrigerant piping joint) Large diameter
Bands for temporary tightening of pipe cover and drain hose
Washer
Drain hose
Pipe cover (for Drain hose) short
Quantity
1
1
6
8
1
1
3.1. Install the indoor unit on a ceiling strong enough
to sustain its weight
[Fig. 3-1] (P.2)
A
C
E
G
1
3
Access door
B Electrical parts box
Air inlet
D Air outlet
Ceiling surface
F Service space (viewed from the side)
Service space (viewed from the direction of arrow)
600 mm or more
2 100 mm or more
10 mm or more
4 300 mm or more
* If the optional long-life filter is installed, the dimensions of the air conditioner
increase.
Rear inlet: Depth increases by 30 mm (*1)
Bottom inlet: Height increases by 30 mm (*2)
4. Fixing hanging bolts
4.1. Fixing hanging bolts
• If necessary, reinforce the hanging bolts with anti-quake supporting members as
countermeasures against earthquakes.
* Use M10 for hanging bolts and anti-quake supporting members (field supply).
[Fig. 4-1] (P.2)
A Center of gravity
(Give site of suspension strong structure.)
1 Reinforcing the ceiling with additional members (edge beam, etc.) must be required to keep the ceiling at level and to prevent the ceiling from vibrations.
Hanging structure
2 Cut and remove the ceiling members.
• Ceiling: The ceiling structure varies from building to one another. For detailed information, consult your construction company.
3 Reinforce the ceiling members, and add other members for fixing the ceiling boards.
Center of gravity and Product Weight
Model name
PEAD-RP35JA(L)Q
PEAD-RP50JA(L)Q
PEAD-RP60JA(L)Q
PEAD-RP71JA(L)Q
PEAD-RP100JA(L)Q
PEAD-RP125JA(L)Q
PEAD-RP140JA(L)Q
W
643
643
643
643
643
643
643
L
954
954
1154
1154
1454
1454
1654
X
340
340
325
325
330
330
332
Y
375
375
525
525
675
675
725
Z
130
130
130
130
130
130
130
Product Weight (kg)
26(25)
28(27)
33(32)
33(32)
41(40)
43(42)
47(46)
The values in the parenthesis are for the PEAD-RP·JALQ model.
5. Installing the unit
5.1. Hanging the unit body
Bring the indoor unit to an installation site as it is packed.
To hang the indoor unit, use a lifting machine to lift and pass through the
hanging bolts.
[Fig. 5-1] (P.2)
A Unit body
B Lifting machine
[Fig. 5-2] (P.2)
C Nuts (field supply)
D Washers (accessory)
E M10 hanging bolt (field supply)
5.2. Confirming the unit’s position and fixing hanging
bolts
Use the gage supplied with the panel to confirm that the unit body and
hanging bolts are positioned in place. If they are not positioned in place, it
may result in dew drops due to wind leak. Be sure to check the positional
relationship.
Use a level to check that the surface indicated by A is at level. Ensure that
the hanging bolt nuts are tightened to fix the hanging bolts.
To ensure that drain is discharged, be sure to hang the unit at level using a
level.
[Fig. 5-3] (P.2)
A Indoor unit’s bottom surface
Caution:
Be sure to install the unit body at level.
14
01_KB79U749H01_GB.p65
14
10.10.14, 9:14
6. Refrigerant piping work
6.1. Refrigerant pipe
6.2.3. Putting nut on
[Fig. 6-5] (P.3)
[Fig. 6-1] (P.3)
a Flare nut
b Copper tube
a Indoor unit
b Outdoor unit
Refer to the Instruction Manual that came with the outdoor unit for the restrictions on
the height difference between units and for the amount of additional refrigerant
charge.
Avoid the following places for installation where air conditioner trouble is liable to
occur.
• Where there is too much oil such as for machine or cooking.
• Salty environment as seaside areas.
• Hot-spring areas.
• Where sulfide gas exists.
• Other special atmospheric areas.
• This unit has flared connections on both indoor and outdoor sides. [Fig. 6-1]
• Refrigerant pipes are used to connect the indoor and outdoor units as shown in the
figure below.
• Insulate both refrigerant and drainage piping completely to prevent condensation.
• Remove flare nuts attached to indoor and outdoor unit, then put them on pipe/tube
having completed burr removal.
(not possible to put them on after flaring work)
6.2.4. Flaring work
[Fig. 6-6] (P.3)
a
b
c
d
e
• Carry out flaring work using flaring tool as shown below.
Pipe diameter
(mm)
Piping preparation
6.35
9.52
12.7
15.88
• Refrigerant pipes of 3, 5, 7, 10 and 15 m are available as optional items.
(1) Table below shows the specifications of pipes commercially available.
Model
Pipe
PEADRP35
PEADRP50
PEADRP60
PEADRP71
PEADRP100
PEADRP125
PEADRP140
For liquid
For gas
For liquid
For gas
For liquid
For gas
For liquid
For gas
For liquid
For gas
For liquid
For gas
For liquid
For gas
Outside diameter
mm
inch
Min wall
thickness
Insulation
thickness
6.35
12.7
6.35
12.7
9.52
15.88
9.52
15.88
9.52
15.88
9.52
15.88
9.52
15.88
1/4
1/2
1/4
1/2
3/8
5/8
3/8
5/8
3/8
5/8
3/8
5/8
3/8
5/8
0.8 mm
0.8 mm
0.8 mm
0.8 mm
0.8 mm
1.0 mm
0.8 mm
1.0 mm
0.8 mm
1.0 mm
0.8 mm
1.0 mm
0.8 mm
1.0 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
8 mm
Insulation
material
Dimension
A (mm)
When the tool for R410A is used
Clutch type
0 - 0.5
0 - 0.5
0 - 0.5
0 - 0.5
+0
B -0.4 (mm)
9.1
13.2
16.6
19.7
Firmly hold copper tube in a die in the dimension shown in the table at above.
6.2.5. Check
[Fig. 6-7] (P.3)
Heat resisting
foam plastic
0.045 specific
gravity
(2) Ensure that the 2 refrigerant pipes are well insulated to prevent condensation.
(3) Refrigerant pipe bending radius must be 10 cm or more.
Caution:
Using careful insulation of specified thickness. Excessive thickness prevents
storage behind the indoor unit and smaller thickness causes dew drippage.
6.2. Flaring work
• Main cause of gas leakage is defect in flaring work.
Carry out correct flaring work in the following procedure.
6.2.1. Pipe cutting
[Fig. 6-3] (P.3)
a
b
c
d
e
f
Flaring tool
Die
Copper tube
Flare nut
Yoke
Copper tubes
Good
No good
Tilted
Uneven
Burred
a
b
c
d
e
Smooth all around
Inside is shining without any scratches
Even length all around
Too much
Tilted
f
g
h
i
Scratch on flared plane
Cracked
Uneven
Bad examples
• Compare the flared work with a figure in right side hand.
• If flare is noted to be defective, cut off the flared section and do flaring work again.
6.3. Pipe connection
[Fig. 6-8] (P.3)
• Apply a thin coat of refrigeration oil on the seat surface of pipe.
• For connection first align the center, then tighten the first 3 to 4 turns of flare nut.
• Use tightening torque table below as a guideline for indoor unit side union joint section,
and tighten using two wrenches. Excessive tightening damages the flare section.
Copper pipe O.D.
(mm)
ø6.35
ø9.52
ø12.7
ø15.88
Flare nut O.D.
(mm)
17
22
26
29
Tightening torque
(N·m)
14 - 18
34 - 42
49 - 61
68 - 82
Warning:
Be careful of flying flare nut! (Internally pressurized)
Remove the flare nut as follows:
1. Loosen the nut until you hear a hissing noise.
2. Do not remove the nut until the gas has been completely released (i.e., hissing noise stops).
3. Check that the gas has been completely released, and then remove the nut.
Outdoor unit connection
• Using a pipe cutter cut the copper tube correctly.
Connect pipes to stop valve pipe joint of the outdoor unit in the same manner applied
for indoor unit.
• For tightening use a torque wrench or spanner, and use the same tightening torque
applied for indoor unit.
6.2.2. Burrs removal
Refrigerant pipe insulation
• After connecting refrigerant piping, insulate the joints (flared joints) with thermal
insulation tubing as shown below.
[Fig. 6-4] (P.3)
a
b
c
d
Burr
Copper tube/pipe
Spare reamer
Pipe cutter
[Fig. 6-9] (P.3)
• Completely remove all burrs from the cut cross section of pipe/tube.
• Put the end of the copper tube/pipe to downward direction as you remove burrs in
order to avoid burrs drop in the tubing.
A Pipe cover (small) (accessory)
B Caution:
Pull out the thermal insulation on the refrigerant piping at the site, insert the flare nut to flare
the end, and replace the insulation in its original position.
Take care to ensure that condensation does not form on exposed copper piping.
C Liquid end of refrigerant piping
D Gas end of refrigerant piping
15
01_KB79U749H01_GB.p65
15
10.10.14, 9:14
6. Refrigerant piping work
E
G
I
K
M
O
Site refrigerant piping
F Main body
Pipe cover (large) (accessory)
H Thermal insulation (field supply)
Pull
J Flare nut
Return to original position
L Ensure that there is no gap here
Plate on main body
N Band (accessory)
Ensure that there is no gap here. Place join upwards.
Tighten the cap to the service port to obtain the initial status.
Retighten the cap
Leak test
1.Remove and discard the rubber bung which is inserted in the end of the unit piping.
2.Flare the end of the site refrigerant piping.
3.Pull out the thermal insulation on the site refrigerant piping and replace the insulation in its original position.
Cautions On Refrigerant Piping
Be sure to use non-oxidative brazing for brazing to ensure that no foreign
matter or moisture enter into the pipe.
Be sure to apply refrigerating machine oil over the flare connection seating
surface and tighten the connection using a double spanner.
Provide a metal brace to support the refrigerant pipe so that no load is
imparted to the indoor unit end pipe. This metal brace should be provided
50 cm away from the indoor unit’s flare connection.
6.5. Drain piping work
• Ensure that the drain piping is downward (pitch of more than 1/100) to the outdoor (discharge) side. Do not provide any trap or irregularity on the way.
• Ensure that any cross-wise drain piping is less than 20 m (excluding the difference of elevation). If the drain piping is long, provide metal braces to prevent it
from waving. Never provide any air vent pipe. Otherwise drain may be ejected.
• Use a hard vinyl chloride pipe VP-25 (with an external diameter of 32 mm) for
drain piping.
• Ensure that collected pipes are 10 cm lower than the unit body’s drain port.
• Do not provide any odor trap at the drain discharge port.
• Put the end of the drain piping in a position where no odor is generated.
• Do not put the end of the drain piping in any drain where ionic gases are generated.
[Fig. 6-10] (P.4)
A
B
C
K
L
M
Correct piping
Wrong piping
Insulation (9 mm or more)
Downward slope (1/100 or more)
Support metal
Air bleeder
Raised
Odor trap
Grouped piping
6.4. Purging procedures leak test
PURGING PROCEDURES
Connect the refrigerant pipes (both the liquid and gas pipes) between the indoor
and the outdoor units.
Remove the service port cap of the stop valve on the side of the outdoor unit gas pipe.
(The stop valve will not work in its initial state fresh out of the factory (totally closed
with cap on).)
Connect the gage manifold valve and the vacuum pump to the service port of the
stop valve on the gas pipe side of the outdoor unit.
Run the vacuum pump. (Vacuumize for more than 15 minutes.)
Check the vacuum with the gage manifold valve, then close the gage manifold valve,
and stop the vacuum pump.
Leave it as is for one or two minutes. Make sure the pointer of the gage manifold
valve remains in the same position. Confirm that the pressure gage show -0.101MPa
(-760 mmHg).
*Close
Stop valve
*Open
Hexagonal wrench
*4 to 5 turns
-0.101MPa Compound pressure
Stop valve (-760 mmHg) gauge (for R410A)
Pressure gauge
(for R410A)
Gauge manifold
valve (for R410A)
Handle High
Handle
Low
Charge hose
Stop
(for R410A)
valve
Vacuum
(or the vacuum
Service port
pump
pump with the
Window
function to
Adapter for
prevent the back
Charge hose preventing
flow)
(for R410A)
the back flow
Remove the gage manifold valve quickly from the service port of the stop valve.
After refrigerant pipes are connected and evacuated, fully open all stop valves on
gas and liquid pipe sides.
Operating without fully opening lowers the performance and causes trouble.
Pipe length :
7 m maximum
No gas charge is needed.
Pipe length exceeding 7 m
Charge the prescribed
amount of gas.
D O. D. ø32 PVC TUBE
E Make it as large as possible. About 10 cm.
F Indoor unit
G Make the piping size large for grouped piping.
H Downward slope (1/100 or more)
I O. D. ø38 PVC TUBE for grouped piping. (9 mm or more insulation)
PEAD-RP·JAQ model
J Up to 700 mm
N Drain hose (accessory)
O Horizontal or slightly upgradient
[PEAD-RP·JAQ model]
1.Insert the drain hose (accessory) into the drain port (insertion margin: 25mm).
(The drain hose must not be bent more than 45° to prevent the hose from breaking or clogging.)
(Attach the hose with glue, and fix it with the band (small, accessory).)
2.Attach the drain pipe (O.D. ø32 PVC TUBE PV-25, field supply).
(Attach the pipe with glue, and fix it with the band (small, accessory).)
3.Perform insulation work on the drain pipe (O.D. ø32 PVC TUBE PV-25) and on
the socket (including elbow).
4.Check the drainage. (Refer to [Fig. 6-13])
5.Attach the insulating material (accessory), and fix it with the band (large, accessory) to insulate the drain port.
[Fig. 6-11] (P.4) *only on the PEAD-RP·JAQ model
A
B
C
D
E
F
G
H
I
Indoor unit
Tie band (accessory)
Visible part
Insertion margin
Drain hose (accessory)
Drain pipe (O.D. ø32 PVC TUBE, field supply)
Insulating material (field supply)
Tie band (accessory)
To be gap free. The joint section of the insulation material meet must be at the top.
[PEAD-RP·JALQ model]
1.Insert the drain hose (accessory) into the drain port.
(The drain hose must not be bent more than 45° to prevent the hose from breaking or clogging.)
The connecting part between the indoor unit and the drain hose may be disconnected at the maintenance. Fix the part with the accessory band, not be adhered.
2.Attach the drain pipe (O.D. ø32 PVC TUBE, field supply).
(Attach the pipe with glue for the hard vinyl chloride pipe, and fix it with the band
(small, accessory).)
3.Perform insulation work on the drain pipe (O.D. ø32 PVC TUBE) and on the
socket (including elbow).
[Fig. 6-12] (P.4) *only on the PEAD-RP·JALQ model
A
B
C
D
E
F
G
Indoor unit
Tie band (accessory)
Band fixing part
Insertion margin
Drain hose (accessory)
Drain pipe (O.D. ø32 PVC TUBE, field supply)
Insulating material (field supply)
16
01_KB79U749H01_GB.p65
16
10.10.14, 9:14
6. Refrigerant piping work
6.6. Confirming drain discharge
Make sure that the drain-up mechanism operates normally for discharge
and that there is no water leakage from the connections.
• Be sure to confirm the above in a period of heating operation.
• Be sure to confirm the above before ceiling work is done in the case of a new
construction.
1. Remove the water supply port cover on the same side as the indoor unit piping.
2. Fill water into the feed water pump using a feed water tank. In filling, be sure to
put the end of the pump or tank in a drain pan. (If the insertion is incomplete,
water may flow over the machine.)
3.Perform the test run in cooling mode, or connect the connector to the ON side of
SWE on the Indoor controller board. (The drain pump and the fan are forced to
operate without any remote controller operation.) Make sure using a transparent
hose that drain is discharged.
SWE
connector
OFF
SWE
ON
<OFF>
OFF
ON
<ON>
4.After confirmation, cancel the test run mode, and turn off the main power. If the
connector is connected to the ON side of SWE, disconnect it and connect it to the
OFF side, and attach the water supply port cover into its original position.
SWE
connector
OFF
<ON>
SWE
ON
OFF
ON
<OFF>
[Fig. 6-13] (P.4)
A
B
C
D
E
F
Insert pump's end 2 to 4 cm.
Remove the water supply port.
About 2500 cc
Water
Filling port
Screw
7. Duct work
•
•
•
•
Connect canvas duct between unit and duct. [Fig. 7-1] (P.5)
Use incombustible material for duct parts.
Provide full insulation to inlet duct flange and outlet duct to prevent condensation.
Be sure to change the position of air filter to a position where it can be serviced.
<A> In case of rear inlet
<B> In case of bottom inlet
A Duct
B Air inlet
C Access door
D Canvas duct
E Ceiling surface
F Air outlet
G Leave distance enough to prevent short cycle
• Procedure for changing the rear inlet to the bottom inlet. [Fig. 7-2] (P.5)
A Filter
B Bottom plate
1. Remove air filter. (First remove filter lock screw.)
2. Remove the bottom plate.
3. Fit the bottom plate to the rear of the body. [Fig. 7-3] (P.5)
(Position of lug-holes on the plate are different from those for rear inlet.)
When the plate is attached on
the rear side, it exceeds the
height of the rear body panel.
Replicate the plate along the slit
when there is not enough room
above for the entire unit.
4. Fit filter to the underside of the body.
(Be careful of which side of the filter to fit.) [Fig. 7-4] (P.5)
C Nail for the bottom inlet
D Nail for the rear inlet
•
•
•
•
•
•
•
Caution:
Inlet duct of 850 mm or more should be construted.
To connect the air conditioner main body and the duct for potential equalization.
To reduce the risk of injury from metal sheet edges, wear protective gloves.
To connect the air conditioner main body and the duct for potential equalization.
The noise from the intake will increase dramatically if intake is fitted directly beneath the main body. Intake should therefore be installed as far
away from the main body as possible.
Particular care is required when using it with bottom inlet specifications.
Install sufficient thermal insulation to prevent condensation forming on
outlet duct flanges and outlet ducts.
Keep the distance between the inlet grille and the fan over 850 mm.
If it is less than 850 mm, install a safety guard not to touch the fan.
To avoid electrical noise interference, do not run transmission lines at the
bottom of the unit.
17
01_KB79U749H01_GB.p65
17
10.10.14, 9:14
8. Electrical work
8.1. Power supply
8.1.1. Indoor unit power supplied from outdoor unit
8.1.2. Separate indoor unit/outdoor unit power supplies (For PUHZ
application only)
The following connection patterns are available.
The outdoor unit power supply patterns vary on models.
The following connection patterns are available.
The outdoor unit power supply patterns vary on models.
1:1 System
1:1 System
* The optional wiring replacement kit is required.
[Fig. 8-1] (P.5)
A
B
C
D
E
F
G
[Fig. 8-3] (P.5)
Outdoor unit power supply
Earth leakage breaker
Wiring circuit breaker or isolating switch
Outdoor unit
Indoor unit/outdoor unit connecting cords
Remote controller (option)
Indoor unit
* Affix a label A that is included with the manuals near each wiring diagram for the
indoor and outdoor units.
[Fig. 8-2] (P.5)
Simultaneous twin/triple/four system
Outdoor unit power supply
Earth leakage breaker
Wiring circuit breaker or isolating switch
Outdoor unit
Indoor unit/outdoor unit connecting cords
Remote controller (option)
Indoor unit
* The optional wiring replacement kits are required.
[Fig. 8-4] (P.5)
* Affix a label A that is included with the manuals near each wiring diagram for the
indoor and outdoor units.
Field electrical wiring
Circuit
rating
Wiring Wire No.
× size (mm2)
Indoor unit model
PEAD
–
Indoor unit power supply (Heater)
Indoor unit power supply (Heater) earth
–
3 × 1.5 (polar)
Indoor unit-Outdoor unit
1 × Min. 1.5
Indoor unit-Outdoor unit earth
Outdoor unit power supply
Earth leakage breaker
Wiring circuit breaker or isolating switch
Outdoor unit
Indoor unit/outdoor unit connecting cords
Remote controller (option)
Indoor unit
Option
Indoor unit power supply
* Affix a label B that is included with the manuals near each wiring diagram for the
indoor and outdoor units.
Simultaneous twin/triple/four system
A
B
C
D
E
F
G
A
B
C
D
E
F
G
H
J
2 × 0.3 (Non-polar)
Remote controller-Indoor unit
*1
Indoor unit (Heater) L-N
*2
–
Indoor unit-Outdoor unit S1-S2
*2
230 V AC
Indoor unit-Outdoor unit S2-S3
*2
24 V DC
Remote controller-Indoor unit
*2
14 V DC
*1. The 10 m wire is attached in the remote controller accessory. Max. 500 m
*2. The figures are NOT always against the ground.
S3 terminal has 24 V DC against S2 terminal. However between S3 and S1, these terminals
are not electrically insulataed by the transformer or other device.
Notes: 1. Wiring size must comply with the applicable local and national code.
2. Power supply cords and indoor unit/outdoor unit connecting cords
shall not be lighter than polychloroprene sheathed flexible cord.
(Design 245 IEC57)
3. Install an earth longer than other cables.
A
B
C
D
E
F
G
H
J
Outdoor unit power supply
Earth leakage breaker
Wiring circuit breaker or isolating switch
Outdoor unit
Indoor unit/outdoor unit connecting cords
Remote controller (option)
Indoor unit
Option
Indoor unit power supply
* Affix a label B that is included with the manuals near each wiring diagram for the
indoor and outdoor units.
If the indoor and outdoor units have separate power supplies, refer to the table at the
below. If the optional wiring replacement kit is used, change the indoor unit electrical
box wiring refering to the figure in the right and the DIP switch settings of the outdoor
unit control board.
Indoor unit specifications
Required
Required
Indoor power supply terminal kit (option)
Indoor unit electrical box connector connection change
Label affixed near each wiring diagram
for the indoor and outdoor units
Outdoor unit DIP switch settings (when
using separate indoor unit/outdoor unit
power supplies only)
Required
ON
OFF
1
2
3
(SW8)
* There are three types of labels (labels A, B, and C). Affix the appropriate labels to
the units according to the wiring method.
Connectors (connections when
shipped from the factory are for indoor
unit power supplied from outdoor unit)
S1
S2
S3
BLUE YELLOW
BLUE YELLOW
L
N
RED
CND
If the indoor and
outdoor units have
separate power
supplies, change the
connections of the
connectors as shown in
the following figure.
Power
supply
board
Connectors
Indoor
controller
board
S1
S2
S3
BLUE YELLOW
YELLOW BLUE
L
N
RED
CND
Power
supply
board
Indoor unit power supplied from outdoor
unit (when shipped from factory)
A breaker with at least 3.0 mm contact
separation in each pole shall be provided.
Use non-fuse breaker (16A) or earth leakage breaker (16A).
18
01_KB79U749H01_GB.p65
18
10.10.14, 9:14
Indoor
controller
board
Separate indoor unit/outdoor unit power
supplies
8. Electrical work
8.2. Indoor wire connection
Work procedure
1.Remove 2 screws to detach the electric component cover.
2.Route each cable through the wiring intake into the electric component box. (Procure power cable and in-out connecting cable locally and use remote control cable
supplied with the unit.)
3.Securely connect the power cable and the in-out connecting cable and the remote
control cable to the terminal blocks.
4.Secure the cables with clamps inside the electric component box.
5.Attach the electric component cover as it was.
• Fix power supply cable and indoor/outdoor cable to control box by using buffer
bushing for tensile force. (PG connection or the like.)
Warning:
• Attach the electrical part cover securely. If it is attached incorrectly, it could
result in a fire, electric shock due to dust, water, etc.
• Use the specified indoor/outdoor unit connecting wire to connect the indoor
and outdoor units and fix the wire to the terminal block securely so that no
stress is applied to the connecting section of the terminal block. Incomplete
connection or fixing of the wire could result in a fire.
[Fig. 8-2-1] (P.6)
[Fig. 8-2-2] (P.6)
C Terminal box
D Knockout hole
E Remove
[Fig. 8-2-3] (P.6)
F Use PG bushing to keep the weight of the cable and external force from being applied to the
power supply terminal connector. Use a cable tie to secure the cable.
G Power source wiring
H Use ordinary bushing
I Transmission wiring
[Fig. 8-2-4] (P.6)
J Terminal block for power source and indoor transmission
K Terminal block for remote controller
• Perform wiring as shown in the diagram to the lower left. (Procure the cable locally.)
Make sure to use cables of the correct polarity only.
[Fig. 8-3] (P.7)
2
3
4
5
6
7
A For installation in the switch box:
B For direct installation on the wall select one of the following:
• Prepare a hole through the wall to pass the remote controller cord (in order to run the remote
controller cord from the back), then seal the hole with putty.
• Run the remote controller cord through the cut-out upper case, then seal the cut-out notch
with putty similarly as above.
C Wall
G Switch box
D Conduit
H Remote controller cord
E Lock nut
I Seal with putty
F Bushing
J Wood screw
B-1. To lead the remote controller cord from the back of the controller:
B-2. To run the remote controller cord through the upper portion:
(3) For direct installation on the wall
2) Connecting procedures
1 Connect the remote controller cord to the terminal block.
[Fig. 8-6] (P.7)
A To the terminal block on the indoor unit
B TB6 (No polarity)
2 Set the dip switch No.1 shown below when using two remote controller’s for the
same group.
3) Function selection of remote controller
If two remote controllers are connected, set one to “Main” and the other to “Sub”. For
setting procedures, refer to “Function selection of remote controller” in the operation
manual for the indoor unit.
A Screw holding cover (1pc)
B Cover
A
B
C
D
E
1
[Fig. 8-5] (P.7)
8.4. Remote controller (wireless remote controller (option))
8.4.1. For wireless remote controller (option)
1) Installation area
• Area in which the remote controller is not exposed to direct sunshine.
• Area in which there is no near by heating source.
• Area in which the remote controller is not exposed to cold (or hot) winds.
• Area in which the remote controller can be operated easily.
• Area in which the remote controller is beyond the reach of children.
* The signal can travel up to approximately 7 meters (in a streight line) within 45 degrees to
both right and left of the center line of the receiver.
Indoor terminal block
Earth wire (green/yellow)
Indoor/outdoor unit connecting wire 3-core 1.5 mm2 or more
Outdoor terminal block
Power supply cord : 2.0 mm2 or more
Connecting cable
Cable 3-core 1.5 mm2, in conformity with Design 245 IEC 57.
Indoor terminal block
Outdoor terminal block
Always install an earth wire (1-core 1.5 mm2) longer than other cables
Remote controller cable
Wire No × size (mm2) : Cable 2C × 0.3
This wire accessory of remote controller
(wire length : 10 m, non-polar. Max. 500 m)
Wired remote controller (option)
Power supply cord
Cable 3-core 2.0 mm2 or more, in conformity with Design 245 IEC 57.
• Connect the terminal blocks as shown in the diagram below.
Caution:
• Use care not to make mis-wiring.
• Firmly tighten the terminal screws to prevent them from loosening.
• After tightening, pull the wires lightly to confirm that they do not move.
8.3. Remote controller (wired remote controller (option))
8.3.1. For wired remote controller
1) Installing procedures
(1) Select an installing position for the remote controller.
The temperature sensors are located on both remote controller and indoor unit.
Procure the following parts locally:
Two piece switch box
Thin copper conduit tube
Lock nuts and bushings
[Fig. 8-4] (P.7)
A Remote controller profile
B Required clearances surrounding the remote controller
C Installation pitch
(2) Seal the service entrance for the remote controller cord with putty to prevent possible invasion of dew drops, water, cockroaches or worms.
19
01_KB79U749H01_GB.p65
19
10.10.14, 9:14
8. Electrical work
8.4.2. Signal Receiving Unit
[Fig. 8-11] (P.8)
1) Sample system connection
[Fig. 8-7] (P.8)
Only the wiring from the signal receiving unit and between the remote controllers is
shown in [Fig. 8-7]. The wiring differs depending on the unit to be connected or the
system to be used.
For details on restrictions, refer to the installation manual or the service handbook
that came with the unit.
1. Connecting to Mr. SLIM air conditioner
(1) Standard 1:1
1 Connecting the signal receiving unit
Connect the signal receiving unit to the CN90 (Connect to the wireless remote controller board) on the indoor unit using the supplied remote controller
wire. Connect the signal receiving units to all the indoor units.
2) How To Install
[Fig. 8-8] (P.8) to [Fig. 8-15] (P.9)
1. Common items for “Installation on the ceiling” and “Installation on the switch
box or on the wall”
[Fig. 8-8] (P.8)
A
B
C
D
Signal receiving unit external
Center of Switch box
Switch box
Installation pitch
E
F
G
H
6.5 mm (1/4 inch)
70 mm (2 - 3/4 inch)
83.5 ± 0.4 mm (3 - 9/32 inch)
Protrusion (pillar, etc)
H Seal around here with putty
I Remote controller wire
J Seal around here with putty
• When opening a hole using a drill for Signal Receiving Unit wire (or taking the
wire out of the back of the Signal Receiving Unit), seal that hole with putty.
• When routing the wire via the portion cut off from the upper case, equally seal
that portion with putty.
(4) Install the remote control wire to the terminal block. [Fig. 8-12] (P.9)
(5) Installing hole when the Signal Receiving Unit is installed on the wall direct.
[Fig. 8-13] (P.9)
• Cut the thin-wall portion inside the bottom case (oblique section) by a knife or a
nipper.
• Take out the connected remote controller wire to the terminal brock through
this space.
(6) Install the lower case on the switch box or directly on the wall. [Fig. 8-14] (P.9)
Mounting the cover [Fig. 8-15] (P.9)
Caution:
• Insert the cover securely until the clicking sound is made. If not doing so, the
cover may fall.
[Fig. 8-9] (P.8)
A Remote controller wire
B Hole (drill a hole on the ceiling to pass the remote controller wire.)
C Signal Receiving Unit
(1) Select the installation site.
The following must be observed.
1 Connect the signal receiving unit to the indoor unit with the supplied remote
controller wire. Note that the length of the remote controller wire is 5 m (16 ft).
Install the remote controller within the reach of the remote controller wire.
2 When installing on either the switch box or the wall, allow space around the
Signal Receiving Unit as shown in the figure in [Fig. 8-8].
3 When installing the Signal Receiving Unit to the switch box, the Signal Receiving Unit slipped downward for 6.5 mm (1/4 inch) as right illustrated.
4 Parts which must be supplied on site.
Switch box for one unit
Thin-copper wiring pipe
Lock nut and bushing
5 The thickness of the ceiling to which the remote controller is installed must be
between 9 mm (3/8 inch) and 25 mm (1 inch).
6 Install the unit on the ceiling or on the wall where the signal can be received
from the wireless remote controller.
The area where the signal from the wireless remote controller can be received is 45 ° and 7 m (22 ft) away from the front of the signal receiving unit.
7 Install the signal receiving unit to the position depending on the indoor unit
model.
8 Connect the remote controller wire securely to the order wire. To pass the
remote controller wire through the conduit, follow the procedure as shown in
[Fig. 8-10].
[Fig. 8-10] (P.8)
A Fix tightly with tape.
B Remote controller wire
C Order wire
Note:
• The point where the remote controller wire is connected differs depending
on the indoor unit model.
Take into account that the remote controller wire cannot be extended when
selecting the installation site.
• lf the Signal Receiving Unit is installed near a fluorescent lamp specially
inverter type,signal interception may occur.
Be careful for installing the Signal Receiving Unit or replacing the lamp.
(2) Use the remote controller wire to connect it to the connector (CN90) on the
controller circuit board on the indoor unit.
Refer to the 2) Setting the Pair Number Switch for details on controller circuit
board on the indoor unit.
(3) Seal the Signal Receiving Unit cord lead-in hole with putty in order to prevent the possible entry of dew, water droplets, cockroaches, other insects,
etc.
8.4.3. Setting
1) Setting the pair number switch
[Fig. 8-16] (P.10)
1. Setting method
Assign the same pair number to the wireless remote controller as that of the indoor
unit. If not doing so, the remote controller cannot be operated. Refer to the installation manual that came with the wireless remote controller for how to set pair
numbers of wireless remote controllers.
Position of daisy wire on the controller circuit board on the indoor unit.
Controller circuit board on the indoor unit (reference) [Fig. 8-16] (P.10)
A CN90: Connector for remote controller wire connection
For pair number settings, the following 4 patters (A-D) are available.
Pair number
setting pattern
Pair number on
remote controller side
Indoor controller circuit board side Point
where the daisy wire is disconnected
A
B
C
D
0
1
2
3~9
Not disconnected
J41 disconnected
J42 disconnected
J41 and J42 disconnected
2. Setting example
(1) To use the units in the same room
[Fig. 8-17] (P.10)
1 Separate setting
Assign a different pair number to each indoor unit to operate each indoor unit
by its own wireless remote controller.
[Fig. 8-18] (P.10)
2 Single setting
Assign the same pair number to all the indoor units to operate all the indoor
units by a single wireless remote controller.
[Fig. 8-19] (P.10)
(2) To use the units in different rooms
Assign the same pair number to the wireless remote controller as that of the
indoor unit. (Leave the setting as it is at purchase.)
2) Setting the Model No.
[Fig. 8-20] (P.10)
1 Insert batteries.
2 Press the SET button with something sharp at the end.
MODEL SELECT blinke and Model No. lighted.
button to set the Model No.
3 Press the temp
4 Press the SET button with something sharp at the end.
MODEL SELECT and Model No. are lighted for three seconds, then turned off.
Indoor Unit Model
A Model No.
PEAD
026
[Fig. 8-11] (P.8)
A
B
C
D
E
F
G
150 mm (5 - 15/16 inch)
Remote controller wire
Wiring pipe
Locknut
Bushing
Switch box
Seal around here with putty
• When installing on the switch box, seal the connections between the switch
box and wiring pipe with putty.
20
01_KB79U749H01_GB.p65
20
10.10.14, 9:14
8. Electrical work
8.5. Function settings (Function selection via the
remote controller)
8.5.1 Function setting on the unit (Selecting the unit functions)
1) For wired remote controller [Fig. 8-21] (P.11)
1. Changing the external static pressure setting.
• Be sure to change the external static pressure setting depending on the duct and
the grill used.
1 Go to the function setting mode.
Switch OFF the remote controller.
Press the A and B buttons simultaneously and hold them for at least 2
seconds. FUNCTION will start to flash.
2 Use the C button to set the refrigerant address (3) to 00.
3 Press D and [--] will start to flash in the unit number (4) display.
4 Use the C button to set the unit number (4) to 01-04 or AL.
5 Press the E MODE button to designate the refrigerant address/unit number.
[--] will flash in the mode number (1) display momentarily.
6 Press the F buttons to set the mode number (1) to 08.
7 Press the G button and the current set setting number (2) will flash.
Use the F button to switch the setting number in response to the external static
pressure to be used.
External static
Setting no. of mode
Setting no. of mode
pressure
no. 10
no. 08
35 Pa
1
2
50 Pa (before shipment)
1
3
70 Pa
2
1
100 Pa
2
2
150 Pa
2
3
8 Press the MODE button E and mode and the setting number (1) and (2) will
change to being on constantly and the contents of the setting can be confirmed.
9 Press the FILTER A and TEST RUN B buttons simultaneously for at least two
seconds. The function selection screen will disappear momentarily and the air
conditioner OFF display will appear.
0 To set the static pressure at 70,100,150Pa, repeat steps 3 to 9. (Set the mode
number to 10 for step 6.)
2. Other functions
1 Select unit number 00 for the settings. (Settings for all indoor units)
Refer to Function table 1.
2 Select unit number 01 to 04 or AL for the settings. (Settings for each indoor unit)
To set the indoor unit in the individual system, select unit number 01.
To set each indoor unit of two, three or four indoor units, which are connected
when these units are simultaneously in operation, select unit number 01 to 04.
To set all indoor units of two, three or four indoor units which are connected when
these units are simultaneously in operation, select AL.
Refer to Function table 2.
2) For wireless remote controller [Fig. 8-22] (P.11)
1. Changing the external static pressure setting.
• Be sure to change the external static pressure setting depending on the duct and
the grill used.
1 Go to the function select mode
Press the CHECK button F twice continuously.
(Start this operation from the status of remote controller display turned off.)
CHECK is lighted and “00” blinks.
Press the TEMP button C once to set “50”. Direct the wireless remote controller
toward the receiver of the indoor unit and press the Hour button A.
2 Setting the unit number
Press the TEMP button C and D to set the unit number to 01-04 or AL. Direct the
wireless remote controller toward the receiver of the indoor unit and press the
Minute button B.
3 Selecting a mode
Enter 08 to change the external static pressure setting using the C and D buttons.
Direct the wireless remote controller toward the receiver of the indoor unit and
press the Hour button A.
Current setting number:
1 = 1 beep (one second)
2 = 2 beeps (one second each)
3 = 3 beeps (one second each)
4 Selecting the setting number
Use the C and D buttons to change the external static pressure setting to be
used.
Direct the wireless remote controller toward the sensor of the indoor unit and
press the Hour button A.
5 To set the external static pressure
Repeat steps 3 and 4 to set the mode number to 10.
6 Complete function selection
Direct the wireless remote controller toward the sensor of the indoor unit and
press the ON/OFF button E.
Note:
• Whenever changes are made to the function settings after installation or maintenance, be sure to record the changes with a mark in the “Setting” column of
the Function table.
3) Changing the power voltage setting (Function table 1)
• Be sure to change the power voltage setting depending on the voltage used.
Function table 1
Select unit number 00
Mode
Power failure automatic recovery*1
(AUTO RESTART FUNCTION)
Indoor temperature detecting
LOSSNAY connectivity
Power voltage
Auto mode
Settings
Not available
Available
Indoor unit operating average
Set by indoor unit’s remote controller
Remote controller’s internal sensor
Not Supported
Supported (indoor unit is not equipped with outdoor-air intake)
Supported (indoor unit is equipped with outdoor-air intake)
240V
220V, 230V
Energy saving cycle automatically enabled
Energy saving cycle automatically disabled
Mode no.
01
02
03
04
05
Setting no. Initial setting
1
(*1)
2
1
2
3
1
2
3
1
2
1
2
Check
Setting no. Initial setting
1
2
3
1
2
3
1
2
3
Check
Function table 2
Select unit numbers 01 to 04 or all units (AL [wired remote controller]/07 [wireless remote controller])
Settings
100 Hr
2500 Hr
No filter sign indicator
Mode
Filter sign
External static pressure
External static
pressure
35 Pa
50 Pa (before shipment)
70 Pa
100 Pa
150 Pa
Mode no.
07
Setting no. of
mode no. 08
2
3
1
2
3
Setting no. of
mode no. 10
1
1
2
2
2
08
10
*1 When the power supply returns, the air conditioner will start 3 minutes later.
Note: When the function of an indoor unit were changed by function selection after the end of installation, always indicate the contents by entering a
appropriate check filed of the tables.
or other mark in the
21
01_KB79U749H01_GB.p65
21
10.10.14, 9:14
9. Test run
9.1. Before test run
After completing installation and the wiring and piping of the indoor and outdoor
units, check for refrigerant leakage, looseness in the power supply or control
wiring, wrong polarity, and no disconnection of one phase in the supply.
Use a 500-volt megohmmeter to check that the resistance between the power
Ω.
supply terminals and ground is at least 1.0 MΩ
Do not carry out this test on the control wiring (low voltage circuit) terminals.
Warning:
Ω.
Do not use the air conditioner if the insulation resistance is less than 1.0 MΩ
Insulation resistance
After installation or after the power source to the unit has been cut for an extended
period, the insulation resistance will drop below 1 MΩ due to refrigerant accumulating in the compressor. This is not a malfunction. Perform the following procedures.
1. Remove the wires from the compressor and measure the insulation resistance of
the compressor.
2. If the insulation resistance is below 1 MΩ, the compressor is faulty or the resistance dropped due the accumulation of refrigerant in the compressor.
3. After connecting the wires to the compressor, the compressor will start to warm
up after power is supplied. After supplying power for the times indicated below,
measure the insulation resistance again.
• The insulation resistance drops due to accumulation of refrigerant in the compressor. The resistance will rise above 1 MΩ after the compressor is warmed
up for two to three hours.
(The time necessary to warm up the compressor varies according to atmospheric conditions and refrigerant accumulation.)
• To operate the compressor with refrigerant accumulated in the compressor,
the compressor must be warmed up at least 12 hours to prevent breakdown.
4. If the insulation resistance rises above 1 MΩ, the compressor is not faulty.
Caution:
• The compressor will not operate unless the power supply phase connection
is correct.
• Turn on the power at least 12 hours before starting operation.
- Starting operation immediately after turning on the main power switch can result in
severe damage to internal parts. Keep the power switch turned on during the operational season.
9.2. Test run
9.2.1. Using wired remote controller
1
2
3
4
5
6
7
8
Turn on the power at least 12 hours before the test run.
Press the [TEST] button twice. ➡ “TEST RUN” liquid crystal display
Press the [Mode selection] button. ➡ Make sure that wind is blown out.
Press the [Mode selection] button and switch to the cooling (or heating) mode.
➡ Make sure that cold (or warm) wind is blown out.
Press the [Fan speed] button. ➡ Make sure that the wind speed is switched.
Check operation of the outdoor unit fan.
Release test run by pressing the [ON/OFF] button. ➡ Stop
Register a telephone number.
The telephone number of the repair shop, sales office, etc., to contact if an error
occurs can be registered in the remote controller. The telephone number will be
displayed when an error occurs. For registration procedures, refer to the operation
manual for the indoor unit.
[Fig. 9-1] (P.11)
A
B
C
D
E
F
G
H
I
M
ON/OFF button
Test run display
Indoor temperature liquid line temperature display
ON/OFF lamp
Power display
Error code display
Test run remaining time display
Set temperature button
Mode selection button
Fan speed button
TEST button
9.2.2. Wired remote controller
1
2
3
4
Turn on the power.
Press the [CHECK] button twice.
Set refrigerant address with [TEMP] button if system control is used.
Press the [ON/OFF] button to stop the self-check.
[Fig. 9-2] (P.11)
CHECK button
Refrigerant address
TEMP. button
IC: Indoor unit
OC: Outdoor unit
E Check code
A
B
C
D
• For description of each check code, refer to the following table.
1 Check code
P1
P2, P9
E6, E7
P4
P5
PA
P6
EE
P8
E4
Fb
E0, E3
E1, E2
E9
UP
U3, U4
UF
U2
U1, Ud
U5
U8
U6
U7
U9, UH
Others
Symptom
Intake sensor error
Pipe (Liquid or 2-phase pipe) sensor error
Indoor/outdoor unit communication error
Drain sensor error
Drain pump error
Forced compressor error
Freezing/Overheating safeguard operation
Communication error between indoor and outdoor units
Pipe temperature error
Remote controller signal receiving error
Indoor unit control system error (memory error, etc.)
Remote controller transmission error
Remote controller control board error
Indoor/outdoor unit communication error (Transmitting error) (Outdoor unit)
Compressor overcurrent interruption
Open/short of outdoor unit thermistors
Compressor overcurrent interruption (When compressor locked)
Abnormal high discharging temperature/49C worked/insufficient refrigerant
Abnormal high pressure (63H worked)/Overheating safeguard operation
Abnormal temperature of heat sink
Outdoor unit fan safeguard stop
Compressor overcurrent interruption/Abnormal of power module
Abnormality of super heat due to low discharge temperature
Abnormality such as overvoltage or voltage shortage and abnormal synchronous signal to main circuit/
Current sensor error
Other errors (Refer to the technical manual for the outdoor unit.)
• On wired remote controller
1 Check code displayed in the LCD.
22
01_KB79U749H01_GB.p65
22
10.10.14, 9:14
Remark
For details, check the LED display
of the outdoor controller board.
9. Test run
9.3. Test run
9.3.1. Using wireless remote controller (option)
[Fig. 9-3] (P.11)
1 Turn on the power to the unit at least 12 hours before the test run.
2 Press the TEST RUN button A twice continuously.
(Start this operation from the status of remote controller display turned off.)
TEST RUN and current operation mode are displayed.
3 Press the MODE button B to activate COOL mode, then check whether cool air
is blown out from the unit.
4 Press the MODE button B to activate HEAT mode, then check whether warm air
is blown out from the unit.
5 Press the FAN button C and check whether fan speed changes.
6 Press the VANE button D and check whether the auto vane operates properly.
7 Press the ON/OFF button to stop the test run.
Note:
• Point the remote controller towards the indoor unit receiver while following
steps 2 to 7.
• It is not possible to run the in FAN, DRY or AUTO mode.
[Output pattern A] Errors detected by indoor unit
Wired remote
controller
Wireless remote controller
Beeper sounds/OPERATION
INDICATOR lamp flashes
(Number of times)
1
2
3
4
5
6
7
8
9
10
11
12
No sound
Symptom
Remark
Check code
P1
P2, P9
E6, E7
P4
P5
P6
EE
P8
E4
–
–
Fb
––
Intake sensor error
Pipe (Liquid or 2-phase pipe) sensor error
Indoor/outdoor unit communication error
Drain sensor error
Drain pump error
Freezing/Overheating safeguard operation
Communication error between indoor and outdoor units
Pipe temperature error
Remote controller signal receiving error
–
–
Indoor unit control system error (memory error, etc.)
No corresponding
[Output pattern B] Errors detected by unit other than indoor unit (outdoor unit, etc.)
Wireless remote controller
Beeper sounds/OPERATION INDICATOR
lamp flashes (Number of times)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Symptom
Remark
Indoor/outdoor unit communication error (Transmitting error) (Outdoor unit)
Compressor overcurrent interruption
Open/short of outdoor unit thermistors
Compressor overcurrent interruption (When compressor locked)
Abnormal high discharging temperature/49C worked/ insufficient refrigerant
Abnormal high pressure (63H worked)/ Overheating safeguard operation
Abnormal temperature of heat sink
Outdoor unit fan protection stop
Compressor overcurrent interruption/Abnormal of power module
Abnormality of super heat due to low discharge temperature
Abnormality such as overvoltage or voltage shortage and abnormal
synchronous signal to main circuit/Current sensor error
–
–
Other errors (Refer to the technical manual for the outdoor unit.)
For details, check the LED
display of the outdoor controller
board.
*1 If the beeper does not sound again after the initial two beeps to confirm the self-check start signal was received and the OPERATION INDICATOR lamp does not
come on, there are no error records.
*2 If the beeper sounds three times continuously “beep, beep, beep (0.4 + 0.4 + 0.4 sec.)” after the initial two beeps to confirm the self-check start signal was
received, the specified refrigerant address is incorrect.
• On wireless remote controller
The continuous buzzer sounds from receiving section of indoor unit.
Blink of operation lamp
• On wired remote controller
Check code displayed on the LCD.
• If the unit cannot be operated properly after the above test run has been performed, refer to the following table to remove the cause.
Symptom
Cause
Wired remote controller
LED 1, 2 (PCB in outdoor unit)
• For about 2 minutes after power-on, operation of the
After LED 1, 2 are lighted, LED 2 is turned
For about 2 minutes
PLEASE WAIT
remote controller is not possible due to system start-up.
off, then only LED 1 is lighted. (Correct
following power-on
(Correct operation)
operation)
• Connector for the outdoor unit’s protection device is not
connected.
PLEASE WAIT → Error code
Only LED 1 is lighted. → LED 1, 2 blink.
• Reverse or open phase wiring for the outdoor unit’s power
After about 2 minterminal block (L1, L2, L3)
utes has expired
Display messages do not appear
following power-on
• Incorrect wiring between indoor and outdoor units
even when operation switch is
Only LED 1 is lighted. → LED 1, 2 blinks
(incorrect polarity of S1, S2, S3)
turned ON (operation lamp does
twice, LED 2 blinks once.
• Remote controller wire short
not light up).
23
01_KB79U749H01_GB.p65
23
10.10.14, 9:14
9. Test run
On the wireless remote controller with conditions above, following phenomena takes place.
• No signals from the remote controller are accepted.
• OPE lamp is blinking.
• The buzzer makes a short ping sound.
Note:
Operation is not possible for about 30 seconds after cancellation of function selection. (Correct operation)
For description of each LED (LED1, 2, 3) provided on the indoor controller, refer to the following table.
LED 1 (power for microcomputer)
Indicates whether control power is supplied. Make sure that this LED is always lit.
LED 2 (power for remote controller)
Indicates whether power is supplied to the remote controller. This LED lights only in the case of
the indoor unit which is connected to the outdoor unit refrigerant address “0”.
LED 3 (communication between indoor and outdoor units)
Indicates state of communication between the indoor and outdoor units. Make sure that this LED is
always blinking.
9.4. AUTO RESTART FUNCTION
Indoor controller board
This model is equipped with the AUTO RESTART FUNCTION.
When the indoor unit is controlled with the remote controller, the operation mode,
set temperature, and the fan speed are memorized by the indoor controller board.
The auto restart function sets to work the moment the power has restored after
power failure, then, the unit will restart automatically.
Set the AUTO RESTART FUNCTION using the remote controller. (Mode no.01)
10.Maintenance
10.1. Gas charge
[Fig. 10-1] (P.12)
A
B
C
D
E
F
G
H
I
J
K
L
M
Indoor unit
Union
Liquid pipe
Gas pipe
Stop valve
Outdoor unit
Refrigerant gas cylinder operating valve
Refrigerant gas cylinder for R410A with siphon
Refrigerant (liquid)
Electronic scale for refrigerant charging
Charge hose (for R410A)
Gauge manifold valve (for R410A)
Service port
1. Connect gas cylinder to the service port of stop valve (3-way).
2. Execute air purge of the pipe (or hose) coming from refrigerant gas cylinder.
3. Replenish specified amount of refrigerant, while running the air conditioner
for cooling.
Note:
In case of adding refrigerant, comply with the quantity specified for the refrigerating
cycle.
Caution:
• Do not discharge the refrigerant into the atmosphere.
Take care not to discharge refrigerant into the atmosphere during installation, reinstallation, or repairs to the refrigerant circuit.
• For additional charging, charge the refrigerant from liquid phase of the gas
cylinder.
If the refrigerant is charged from the gas phase, composition change may
occur in the refrigerant inside the cylinder and the outdoor unit. In this case,
ability of the refrigerating cycle decreases or normal operation can be impossible. However, charging the liquid refrigerant all at once may cause the compressor to be locked. Thus, charge the refrigerant slowly.
To maintain the high pressure of the gas cylinder, warm the gas cylinder with warm
water (under 40°C) during cold season. But never use naked fire or steam.
24
01_KB79U749H01_GB.p65
24
10.10.14, 9:14
This product is designed and intended for use in the residential,
commercial and light-industrial environment.
The product at hand is
based on the following
EU regulations:
• Low Voltage Directive 2006/95/EC
• Electromagnetic Compatibility Directive
2004/108/EC
Please be sure to put the contact address/telephone number on
this manual before handing it to the customer.
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Authorized representative in EU: MITSUBISHI ELECTRIC EUROPE B.V.
HARMAN HOUSE, 1 GEORGE STREET, UXBRIDGE, MIDDLESEX UB8 1QQ, U.K.
KB79U749H01
00a_KB79U749H01_Cover.p65
2
10.10.14, 9:13