IP Link® De vice Interface
Communication Sheet
smsg_10_3393_10.pke
Revision: 9/24/2010
This document provides additional assistance with wiring your Extron IP Link enabled product to your device.
Different components may require a different wiring scheme than those listed below.
For complete operating instructions, refer to the user's manual for the specific Extron IP Link enabled product or
the controlled device manufacturer supplied documentation.
Device Specifications:
Device Type:
Manufacturer:
Firmware Version:
Model(s):
Display
Samsung
N/A
320MP-2, P42HP, P50FP, P50HP, P63FP, SyncMaster 320MX, SyncMaster 320MXN,
SyncMaster 400FP-2, SyncMaster 400MP, SyncMaster 400MX, SyncMaster 400MX-2,
SyncMaster 400MXN, SyncMaster 460FP-2, SyncMaster 460MX, SyncMaster 460MXN,
SyncMaster 520DX, SyncMaster 460MXn-2, SyncMaster 460MX-2
Version History:
Driver
Version
Date
IP Link
Compiler
GC
Version
10
9/24/2010
1.4.0
3.0.3
Added Channel Step Control.
9
9/8/2010
1.4.0
3.0.3
8
08/05/2010
1.4.0
3.0.3
Added models SyncMaster 460MXn-2 and SyncMaster 460MX2
Added Channel Control.
7
02/24/2010
1.4.0
3.0.2
Added Signal Status.
6
02/22/2010
1.4.0
3.0.2
Added Volume control for the MLC62 driver.
5
09/25/2009
1.4.0
3.0.1
Added models 320MP-2, SyncMaster 400FP-2, SyncMaster
460FP-2.
4
09/10/2009
1.4.0
3.0.1
Added model SyncMaster 400MX-2.
2
03/23/2009
1.3.11.1
2.5.0
Updated volume command. Added support for SyncMaster
400MP, P50HP, P42HP, P50FP, and P63FP.
1
02/12/2009
1.3.11.1
2.5.0
Initial version.
Notes
Driver Notes:
• Device ID needs to be set to 01.
• Driver is not recommended with pass-through mode.
Page 1 of 6
IP Link® De vice Interface
Communication Sheet
smsg_10_3393_10.pke
Revision: 9/24/2010
Control Commands & States:
Aspe ct Ratio (Compute r)
4:3
16:9
Aspe ct Ratio (Video)
Wide
Zoom 1
16:9
4:3
Audio Mute
On
Off
Auto Image
Execute
Channel
0-9
.
Zoom 2
Clear
Enter
Channel TV (S tep)
Up
Down
Exe cutive Mode *
Mode 1
Mode 2
Off
Input
PC
BNC
DVI
AV
S- Video
Component
MagicNet
RF
DT V
HDMI
DVI (HDCP)
IR Remote
Enable
Disable
On Screen Display
On
Off
Picture In Picture
On
Off
PIP Input
PC
DVI
S- Video
Component
Upper Left
Upper Right
Lower Left
Large
Small
Double 1
Double 2
Double 3
PIP Position
AV
Lower Right
PIP Size
PIP Swap
Execute
Powe r Control
On
Off
Signal Sele ct**
Analog
Digital
Tune r Mode***
Air
Cable
Volume (Discre te)
0 - 100
Page 2 of 6
smsg_10_3393_10.pke
IP Link® De vice Interface
Communication Sheet
Revision: 9/24/2010
*Mode 1 locks IR remote and front panel controls. Mode 2 locks only front panel controls.
**Signal Select is defaulted to Digital.
*** T uner Mode is defaulted to Cable.
****Displays the channel being pressed.
Channel Control:
Channel, Signal Select and tuner Mode are all part of the channel selection. If using in a macro you will need to put
a 1 second delay between these commands.
If the channel you de sire is 12 on a Analog signal and off Cable then:
• Select Analog under Signal Select
• Select Cable under T uner Mode
• Select 1 then 2
• Select Enter.
If the channel you de sire is 12.15 on a Digital signal and off the Air then:
• Select Digital under Signal Select
• Select Air under T uner Mode
• Select 1 then 2
• Select ‘.’
• Select 1 then 5
• Select Enter.
Page 3 of 6
IP Link® De vice Interface
Communication Sheet
smsg_10_3393_10.pke
Revision: 9/24/2010
Status Available:
Aspe ct Ratio (Compute r)
4:3
16:9
Aspe ct Ratio (Video)
Wide
Zoom 1
16:9
4:3
Audio Mute
On
Off
Connection Status
Connected
Disconnected
Exe cutive Mode *
Mode 1
Mode 2
Off
Input
PC
BNC
DVI
AV
S- Video
Component
MagicNet
RF
DT V
HDMI
DVI (HDCP)
IR Remote
Enable
Disable
Major Channel**
Channel
Minor Channel**
Channel
On Screen Display
On
Off
Picture In Picture
On
Off
PIP Input
PC
DVI
S- Video
Component
Large
Small
Double 2
Double 3
Powe r Control
On
Off
Signal Status
Active
Inactive
Signal Sele ct**
Analog
Digital
Tune r Mode**
Air
Cable
Volume (Discre te)
0 - 100
PIP Size
Zoom 2
AV
Double 1
Status Unavailable
* Mode 1 locks IR remote and front panel controls. Mode 2 locks only front panel controls.
**Not true status, used for indication.
Page 4 of 6
IP Link® De vice Interface
Communication Sheet
smsg_10_3393_10.pke
Revision: 9/24/2010
MLC62 Supported Commands:
Aspe ct Ratio (Compute r)
4:3
16:9
Aspe ct Ratio (Video)
Wide
Zoom 1
16:9
4:3
Audio Mute
On
Off
Auto Image
Execute
Channel TV (S tep)
Up
Down
Exe cutive Mode *
Mode 1
Mode 2
Off
Input
PC
BNC
DVI
AV
S- Video
Component
MagicNet
RF
DT V
HDMI
DVI (HDCP)
IR Remote
Enable
Disable
On Screen Display
On
Off
Picture In Picture
On
Off
PIP Input
PC
DVI
S- Video
Component
Upper Left
Upper Right
Lower Left
Large
Small
Double 1
Double 2
Double 3
PIP Position
Zoom 2
AV
Lower Right
PIP Size
PIP Swap
Execute
Powe r Control
On
Volume (Discre te)
0 to 100 in steps of 1
Off
* Mode 1 locks IR remote and front panel controls. Mode 2 locks only front panel controls.
Page 5 of 6
smsg_10_3393_10.pke
IP Link® De vice Interface
Communication Sheet
Revision: 9/24/2010
Cable and Adapter Requirements:
F/F RS-232 Straight Serial Cable
Notes for the Device:
•
The “Power Save” feature of the display needs to be disabled in order for the driver to work properly.
There are no driver controls available for the Power Save feature.
•
If the main input is a high resolution input (i.e. PC), the PIP input cannot also be a high resolution input and vice
versa.
Auto Image is only available for PC and BNC inputs.
•
Serial communication:
Port Type : RS-232
Baud Rate: 9600
Data Bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
Pin Assignments Diagram:
Note: Captive screw connector may also be used as a serial connection.
General Notes:
Page 6 of 6