DMO2420
Microwave
Parts and Service Manual
DMO2420B
DMO2420R
DMO2420S
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
When the testing is completed,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
Before Servicing
1. Disconnect the power supply cord
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
, and then remove
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
After repairing
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for 60
seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an
insulated screwdriver.
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
Whenever troubleshooting is performed the power supply
must be disconnected. It may, in some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that the leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water remains
cold carry out Before Servicing procedure and re-examine
the connections to the component being tested.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and a microwave leakage test should be carried out.
1
DMO2420B
DMO2420R
DMO2420S
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches Primary interlock relay and door sensing switch shall prevent microwave radiation emission in
excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission
in excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for
microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5½C (68½F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and
made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode.
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed, replace
it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on the
meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the secondary interlock switch does turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
DMO2420B
DMO2420R
DMO2420S
SERVICE MANUAL
distinctive appliances
PRODUCT DESCRIPTION
MICROWAVE OVEN
DMO2420B/DMO2420R/DMO2420S
GENERAL INFORMATION
FOREWORD
This Manual has been prepared to provide Dacor Service Personnel
with Operation and Service Information for the DACOR MICROWAVE OVENS, DMO2420B, DMO2420R and DMO2420S.
OPERATION
It is recommended that service personnel carefully study the entire text
of this manual so that they will be qualified to render satisfactory
customer service.
TROUBLESHOOTING GUIDE AND
TEST PROCEDURE
Check the interlock switches and the door seal carefully. Special
attention should be given to avoid electrical shock and microwave
radiation hazard.
TOUCH CONTROL PANEL
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
COMPONENT REPLACEMENT
AND ADJUSTMENT PROCEDURE
WIRING DIAGRAM
Servicing and repair work must be carried out only by trained service
personnel.
DANGER
Certain initial parts are intentionally not grounded and present
a risk of electrical shock only during servicing. Service
personnel - Do not contact the following parts while the
appliance is energized;
High Voltage Capacitor, Power Transformer, Magnetron, High
Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more than
250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “∆” on parts list may cause undue microwave
exposure, by themselves, or when they are damaged, loosened or
removed.
distinctive appliances
950 SOUTH RAYMOND AVE.
PASADENA, CA 91105
3
PARTS LIST
DMO2420B
DMO2420R
DMO2420S
SPECIFICATION
ITEM
DESCRIPTION
Power Requirements
120 Volts / 13.8 Amperes
60 Hertz
Single phase, 3 wire grounded
Power Output
1200 watts (IEC TEST PROCEDURE)
Operating frequency of 2450MHz
Case Dimensions
Width
24"
Height 13-3/8"
Depth 19-1/8"
Cooking Cavity Dimensions
Width 17-3/8"
Height 10-1/2"
Depth 18-5/8"
2.0 Cubic Feet
Control Complement
Touch Control System
Clock ( 1:00 - 12:59 )
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
100 PERCENT ............................. Full power throughout the cooking time
90 PERCENT............................................... approx. 90% of Full Power
80 PERCENT............................................... approx. 80% of Full Power
70 PERCENT............................................... approx. 70% of Full Power
60 PERCENT............................................... approx. 60% of Full Power
50 PERCENT............................................... approx. 50% of Full Power
40 PERCENT............................................... approx. 40% of Full Power
30 PERCENT.............................................. approx. 30% of Full Power
20 PERCENT............................................... approx. 20% of Full Power
10 PERCENT............................................... approx. 10% of Full Power
0 PERCENT.............................. No power throughout the cooking time
Sensor Cooking pads, Breakfast pad, Lunch pad
15 Minute Dinner pad, Auto Defrost pad, Microwave Recipes pad
Beverage pad, Number selection pads, Timer/Clock pad
Keep Warm Plus pad, Easy Minute pad, Power Level pad
Stop/Clear pad, Start/Instant On pad
Oven Cavity Light
Yes
Safety Standard
UL Listed
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed
and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.
WARNING:
Improper use of the grounding plug can result in a risk of electric shock.
Electrical Requirements
The electrical requirements are a 120 volt 60 Hz, AC only, 15 or 20 amp. fused electrical supply. It is recommended that a
separate circuit serving only this appliance be provided. When installing this appliance, observe all applicable codes and
ordinances.
A short power-supply cord is provided to reduce risks of becoming entangled in or tripping over a longer cord.
4
DMO2420B
DMO2420R
DMO2420S
Where a two-pronged wall-receptacle is encountered, it is the personal
responsibility and obligation of the customer to contact a qualified
electrician and have it replaced with a properly grounded three-pronged
wall receptacle or have a grounding adapter properly grounded and
polarized. If the extension cord must be used, it should be a 3-wire, 15
amp. or higher rated cord. Do not drape over a countertop or table where
it can be pulled on by children or tripped over accidentally.
Grounded
Receptacle Box
3-Pronged
Plug
CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND GROUNDING PRONG FROM THIS
PLUG.
OVEN DIAGRAM
5
6
7
12
9
11
8
10
2
1
4
3
TOUCH CONTROL PANEL
Grounding Pin
3-Pronged Receptacle
1. One touch door open button.
Push to open door.
2. Door latches.
The oven will not operate unless
the door is securely closed.
3. Removable turntable support.
4. Removable turntable.
The turntable will rotate clockwise
or counterclockwise.
5. Oven lamp.
It will light when oven is operating
or door is opened.
6. Oven door with see-through
window.
7. Ventilation openings. (Rear)
8. Auto-Touch control panel.
9. Time display: Digital display, 99
minutes 99 seconds.
10. Coupling.
11. Wave guide cover.
12. Power supply cord.
NOTE:
The directed features are disabled
after three minutes when the oven
is not in use. These features are
automatically enabled when the
door is opened and closed or the
STOP/ CLEAR pad is pressed.
DMO2420R
DMO2420B
DMO2420S
5
DMO2420B
DMO2420R
DMO2420S
OPERATION
DESCRIPTION OF OPERATING SEQUENCE
the secondary interlock switch and primary interlock
relay and is mechanically associated with the door so that
it will function in the following sequence.
(1) When the door opens from the closed position, the
primary interlock relay (RY2) and secondary interlock
switch open their contacts. And contacts of the relay
(RY1) remains closed. Then the monitor switch contacts
close.
(2) When the door is closed from the open position, the
monitor switch contacts open first. Then the contacts of
the secondary interlock switch and door sensing switch
close. And contacts of the relay (RY1) open.
If the secondary interlock switch and primary interlock relay
(RY2) fail with the contacts closed when the door is opened,
the closing of the monitor switch contacts will form a short
circuit through the monitor fuse, secondary interlock switch,
relay (RY1) and primary interlock relay (RY2), causing the
monitor fuse to blow.
The following is a description of component functions during
oven operation.
OFF CONDITION
Closing the door activates the door sensing switch and
secondary interlock switch. (In this condition, the monitor
switch contacts are opened.)
When oven is plugged in, 120 volts A.C. is supplied to the
control unit. (Figure O-1).
1. The display will show "Welcome".
To set any program or set the clock, you must first touch
the STOP/CLEAR pad. The display will clear, and " : "
will appear.
COOKING CONDITION
Program desired cooking time by touching the NUMBER
pads. Program the power level by touching the POWER
LEVEL pad.
When the START pad is touched, the following operations
occur:
POWER LEVEL 0% TO 100% COOKING
When Variable Cooking Power is programmed, the 120
volts A.C. is supplied to the power transformer intermittently
through the contacts of relay (RY-2) which is operated by the
control unit within a 32 second time base. Microwave power
operation is as follows:
1. The contacts of relays are closed and components
connected to the relays are turned on as follows.
(For details, refer to Figure O-2)
VARI-MODE
RELAY
RY-1
RY-2
CONNECTED COMPONENTS
oven lamp/turntable motor/fan motor
power transformer
2. 120 volts A.C. is supplied to the primary winding of the
power transformer and is converted to about 3.2 volts
A.C. output on the filament winding, and approximately
2360 volts A.C. on the high voltage winding.
3. The filament winding voltage heats the magnetron filament
and the H.V. winding voltage is sent to a voltage doubler
circuit.
4. The microwave energy produced by the magnetron is
channelled through the waveguide into the cavity feedbox, and then into the cavity where the food is placed to
be cooked.
5. Upon completion of the cooking time, the power
transformer, oven lamp, etc. are turned off, and the
generation of microwave energy is stopped. The oven
will revert to the OFF condition.
6. When the door is opened during a cook cycle, the monitor
switch, door sensing switch, secondary interlock switch,
relay (RY1) and primary interlock relay are activated with
the following results. The circuits to the turntable motor,
the cooling fan motor, and the high voltage components
are de-energized, the oven lamp remains on, and the
digital read-out displays the time still remaining in the
cook cycle when the door was opened.
7. The monitor switch electrically monitors the operation of
ON TIME
OFF TIME
100% power
32 sec.
0 sec.
approx. 90% power
30 sec.
2 sec.
approx. 80% power
26 sec.
6 sec.
approx. 70% power
24 sec.
8 sec.
approx. 60% power
22 sec.
10 sec.
approx. 50% power
18 sec.
14 sec.
approx. 40% power
16 sec.
16 sec.
approx. 30% power
12 sec.
20 sec.
approx. 20% power
8 sec.
24 sec.
approx. 10% power
6 sec.
26 sec.
0% power
0 sec.
32 sec.
Note:
The ON/OFF time ratio does not correspond with the
percentage of microwave power, because approx. 2
seconds are needed for heating of the magnetron
filament.
SENSOR COOKING CONDITION
Using the SENSOR function, the food is cooked without
figuring time, power level or quantity. When the oven senses
enough steam from the food, it relays the information to its
microprocessor which will calculate the remaining cooking
time and power level needed for best results. When the food
is cooked, water vapor is developed. The sensor “senses”
the vapor and its resistance increases gradually. When the
resistance reaches the value set according to the menu,
supplementary cooking is started.
6
DMO2420B
DMO2420R
DMO2420S
The time of supplementary cooking is determined by experiment with each food category and inputted into the LSI.
An example of how sensor works: (POTATOES)
1. Potatoes at room temperature.
Vapor is emitted very
MIC
RO
WA
slowly.
VE
2. Heat Potatoes. Moisture and humidity is emitted rapidly.
You can smell the aroma asMitICcooks.
AH SENSOR
RO
WA
VE
3. Sensor detects moisture and humidity and calculates
cooking time and variable power.
Cooking Sequence.
1. Touch one of the SENSOR pads and then touch the Start
pad.
NOTE: The oven should not be operated on SENSOR
immediately after plugging in the unit. Wait two
minutes before cooking on SENSOR.
2. The coil of shut-off relay (RY-1) is energized, the turntable
motor, oven lamp and cooling fan motor are turned on,
but the power transformer is not turned on.
3. After about 16 seconds, the cook relay (RY-2) is energized.
The power transformer is turned on, microwave energy
is produced and first stage is started.
The 16 seconds is the cooling time required to remove
any vapor from the oven cavity and sensor.
NOTE: During this first stage, do not open the door or touch
STOP/CLEAR pad.
4. When the sensor detects the vapor emitted from the
food, the display switches over to the remaining cooking
time and the timer counts down to zero.
At this time, the door may be opened to stir, turn, or
season food.
5. When the timer reaches zero, an audible signal sounds.
The shut-off relay and cook relay are de-energized and
the power transformer, oven lamp, etc. are turned off.
6. Opening the door or touching the STOP/CLEAR pad, the
time of day will reappear on the display and the oven will
revert to an OFF condition.
7
DMO2420B
DMO2420R
DMO2420S
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CLOCK APPEARS ON DISPLAY.
MAGNETRON
TEMP.
FUSE
NOTE:
Indicates components with potential above 250 V.
MONITOR
FUSE 20A
COM.
N.O.
CAPACITOR 1.0µF
AC 2300V
F1
AH SENSOR
(RY-2)
PRIMARY
INTERLOCK
RELAY
(RY-1)
A1
F2
F3
A2
GRN
CONTROL UNIT
N.O.
COM.
120V AC
60 Hz
B1
POWER
TRANSFORMER
B2
N.C.
DOOR
SENSING
SWITCH
CAVITY
TEMP.
FUSE
TTM
OL
OVEN
LAMP
MONITOR
SWITCH
FM
TURNTABLE
MOTOR
COM.
H.V. RECTIFIER
MAGNETRON
FAN
MOTOR
SECONDARY
INTERLOCK
SWITCH
Figure O-1. Oven Schematic-Off Condition
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. COOKING TIME PROGRAMMED.
3. VARIABLE COOKING CONTROL "P-HI/ 100 PERCENT".
4. "START" PAD TOUCHED.
MAGNETRON
TEMP.
FUSE
MONITOR
FUSE 20A
COM.
N.O.
F3
A2
(RY-2)
PRIMARY
INTERLOCK
RELAY
(RY-1)
F1
A1
F2
CAPACITOR 1.0µF
AC 2300V
GRN
CONTROL UNIT
N.O.
COM.
120V AC
60 Hz
B1
CAVITY
TEMP.
FUSE
POWER
TRANSFORMER
B2
N.C.
DOOR
SENSING
SWITCH
TTM
OL
OVEN
LAMP
TURNTABLE
MOTOR
MONITOR
SWITCH
FM
COM.
H.V. RECTIFIER
MAGNETRON
FAN
MOTOR
SECONDARY
INTERLOCK
SWITCH
Figure O-2. Oven Schematic-Cooking Condition
8
DMO2420B
DMO2420R
DMO2420S
DESCRIPTION AND FUNCTION OF COMPONENTS
DOOR OPEN MECHANISM
open, the monitor fuse blows simultaneously with closing
of the monitor switch contacts.
CAUTION: BEFORE REPLACING A BLOWN MONITOR
FUSE TEST THE DOOR SENSING SWITCH,
PRIMARY INTERLOCK RELAY (RY2), RELAY
(RY1), SECONDARY INTERLOCK SWITCH
AND MONITOR SWITCH FOR PROPER OPERATION. (REFER TO CHAPTER "TEST PROCEDURE").
NOTE: MONITOR FUSE AND MONITOR SWITCH ARE
REPLACED AS AN ASSEMBLY.
The door is opened by pushing the open button on the control
panel, refer to the Figure D-1. When the open button is
pushed, the open button pushes up the switch lever, and
then the switch lever pushes up the latch head. The latch
heads are moved upward and released from latch hook.
Now the door will open.
Latch Heads
Door
TURNTABLE MOTOR
Door Sensing
Switch
The turntable motor rotates the turntable located on the
bottom of the oven cavity, so that the foods on the turntable
cook evenly during cooking. The turntable may turn in either
direction.
Monitor Switch
Switch Lever
COOLING FAN MOTOR
The cooling fan motor drives a blade which draws external cool
air. This cool air is directed through the air vanes surrounding
the magnetron and cools the magnetron. This air is channelled
through the oven cavity to remove steam and vapors given off
from the heating foods. It is then exhausted through the
exhausting air vents at the oven cavity.
Secondary Interlock
Switch
Figure D-1. Door Open Mechanism
DOOR SENSING AND SECONDARY INTERLOCK
SWITCHES
MONITOR FUSE
The secondary interlock switch is mounted in the lower
position of the latch hook and the door sensing switch in the
primary interlock system is mounted in the upper position of
the latch hook. They are activated by the latch heads on the
door. When the door is opened, the switches interrupt the
power to all high voltage components. A cook cycle cannot
take place until the door is firmly closed thereby activating
both interlock switches. The primary interlock system consists of the door sensing switch and primary interlock relay
located on the control circuit board.
1. The monitor fuse blows when the contacts (COM-NO) of
the primary interlock relay (RY2) and secondary interlock
switch remain closed with the oven door open and when
the monitor switch closes.
2. If the wire harness or electrical components are shortcircuited, this monitor fuse blows to prevent an electric
shock or fire hazard.
CAVITY TEMPERATURE FUSE
The cavity temperature fuse located on the top of the oven
cavity, is designed to prevent damage to the oven by fire. If the
food load is overcooked, by either error in cook time or defect
in the control unit, the cavity temperature fuse will open.
Under normal operation, the cavity temperature fuse remains
closed. However, when abnormally high temperatures are
reached within the oven cavity, the cavity temperature fuse will
open at 302½F(150½C) causing the oven to shut down.
NOTE: This is a fuse. It does not reset.
MONITOR SWITCH
The monitor switch is activated (the contacts opened) by the
latch head on the door while the door is closed. The switch
is intended to render the oven inoperative, by means of
blowing the monitor fuse, when the contacts of the primary
interlock relay (RY2) and secondary interlock switch fail to
open when the door is opened.
MAGNETRON TEMPERATURE FUSE
Functions:
1. When the door is opened, the monitor switch contact close
(to the ON condition) due to their being normally closed. At
this time the primary interlock relay (RY2) and secondary
interlock switch are in the OFF condition (contacts open)
due to their being normally open contact switches.
2. As the door goes to a closed position, the monitor switch
contacts are first opened and then the door sensing switch
and the secondary interlock switch contacts close. (On
opening the door, each of these switches operate inversely.)
3. If the door is opened, and the primary interlock relay
(RY2) and secondary interlock switch contacts fail to
The magnetron temperature fuse located near the magnetron
is designed to prevent damage to the magnetron if an over
heated condition develops in the tube due to cooling fan failure,
obstructed air guide, dirty or blocked air intake, etc.
Under normal operation, the magnetron temperature fuse
remains closed. However, when abnormally high temperatures are reached within the magnetron, the magnetron temperature fuse will open at 302½F(150½C) causing the oven to
shut down.
NOTE: This is a fuse. It does not reset.
9
DMO2420B
DMO2420R
DMO2420S
TROUBLESHOOTING GUIDE
Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is connected.
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many
of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which
will be found in the "Test Procedure "section.
IMPORTANT: If the oven becomes inoperative because of a blown monitor fuse, check the monitor switch, relay (RY1)
primary interlock relay (RY2), door sensing switch and secondary interlock switch before replacing the
monitor fuse. If the monitor fuse is replaced, the monitor switch must also be replaced. Use part FFS-BA016/
KIT as an assembly.
IMPORTANT: Whenever troubleshooting is performed with the power supply cord disconnected. It may in, some cases, be
necessary to connect the power supply cord after the outer case has been removed, in this event,
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
When the testing is completed
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect all leads removed from components during testing.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is installed.
7. Run the oven and check all functions.
10
DMO2420B
DMO2420R
DMO2420S
CK = Check / RE = Replace
POSSIBLE CAUSE
AND
DEFECTIVE PARTS
CONDITION
PROBLEM
RE RE A B C D E E F F G H RE RE CK I CK CK CK J K L M N
SHORT IN POWER CORD
SHORT OR OPENED WIRING
MAGNETRON
POWER TRANSFORMER
H.V. RECTIFIER ASSEMBLY
HIGH VOLTAGE CAPACITOR
CAVITY TEMPERATURE FUSE
MAGNETRON TEMPERATURE FUSE
PRIMARY INTERLOCK SYSTEM
SECONDARY INTERLOCK SWITCH
MONITOR SWITCH
MONITOR FUSE
OVEN LAMP OR SOCKET
COOLING FAN MOTOR
TURNTABLE MOTOR
TOUCH CONTROL PANEL
WRONG OPERATION
LOW VOLTAGE
DIRTY OVEN CAVITY
KEY UNIT
RELAY (RY1)
DEFROST CENTER
FOIL PATTERN ON PWB.
AH SENSOR
TEST PROCEDURE
Home fuse or circuit breaker blows when
power cord is plugged into wall receptacle.
OFF
CONDITION
COOKING
CONDITION
SENSOR
COOKING
CONDITION
Monitor fuse blows when power cord is
plugged into wall receptacle.
Any letters or indicators do not appear in
display when power cord is first plugged
into wall outlet.
Display does not operate properly when
STOP/CLEAR key is touched. (Buzzer
should sound and ":" or time of day
should appear in display.)
Oven lamp does not light when door is
opened.
Oven lamp does not go out when door is
closed.
Oven lamp lights but fan motor and
turntable motor do not operate.
Oven does not go into cook cycle when
START pad is touched
Oven seems to be operating but little or
no heat is produced in oven load. (Food
incompletely cooked or not cooked at all
at end of cook cycle.)
Oven goes into a cook cycle but
extremely uneven heating is produced in
oven load (food).
Oven does not cook properly when
programmed for P-50/ 50 PERCENT
mode. (Operates properly on P-HI/ 100
PERCENT mode.)
Oven goes into Defrost Center but food
is not defrosted well.
AH sensor does not end during Sensor
cooking condition. (Oven does not shut
off after a cup of water is boiling by
sensor cooking.)
Oven stops at 16 sec. after starting.
11
DMO2420B
DMO2420R
DMO2420S
TEST PROCEDURES
PROCEDURE
LETTER
A
COMPONENT TEST
MAGNETRON ASSEMBLY TEST
1.
2.
3.
4.
5.
6.
7.
8.
9.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check
across the magnetron filament leads should indicate less than 1 ohm.
To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads
and chassis ground. This test should indicate an infinite resistance. If there is little or no resistance
the magnetron is grounded and must be replaced.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
MICROWAVE OUTPUT POWER
The following test procedure should be carried out with the microwave oven in a fully assembled condition
(outer case fitted).
HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD
BE OBSERVED.
Power output of the magnetron can be measured by performing a water temperature rise test. This test
should only be used if above tests do not indicate a faulty magnetron and there is no defect in the following
components or wiring: silicon rectifier, high voltage capacitor and power transformer. This test will require
a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple type
temperature tester. For accurate results, the following procedure must be followed carefully:
1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water with
a thermometer or thermocouple temperature tester. Stir the thermometer or thermocouple through
the water until the temperature stabilizes. Record the temperature of the water.
2. Place the cup of water in the oven. Operate oven at 100 PERCENT POWER/ P-HI selecting more than
60 seconds cook time. Allow the water to heat for 60 seconds, measuring with a stop watch, second
hand of a watch or the digital read-out countdown.
3. Remove the cup from the oven and again measure the temperature, making sure to stir the
thermometer or thermocouple through the water until the maximum temperature is recorded.
4. Subtract the cold water temperature from the hot water temperature. The normal result should be 33
to 62½F(18.6 to 34.5½C) rise in temperature. If the water temperatures are accurately measured and
tested for the required time period the test results will indicate if the magnetron tube has low power
output (low rise in water temperature) which would extend cooking time or high power output (high rise
in water temperature) which would reduce cooking time. Because cooking time can be adjusted to
compensate for power output, the magnetron tube assembly should be replaced only if the water
temperature rise test indicates a power output well beyond the normal limits. The test is only accurate
if the power supply line voltage is 120 volts and the oven cavity is clean.
B
POWER TRANSFORMER TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the primary input terminals and measure the resistance of the transformer with an
ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of
the primary coil should be less than 1 ohm and the resistance of the high voltage coil should be
approximately 90 ohms; the resistance of the filament coil should be less than 1 ohm.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
12
DMO2420B
DMO2420R
DMO2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO
MEASURE THE FILAMENT AND HIGH VOLTAGE.)
C
HIGH VOLTAGE RECTIFIER TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance
across the terminals and observe, reverse the leads to the rectifier terminals and observe meter
reading. If a short is indicated in both directions, or if an infinite resistance is read in both directions,
the rectifier is probably defective and should be replaced.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.
D
HIGH VOLTAGE CAPACITOR TEST
1.
2.
3.
4.
5.
6.
7.
8.
E
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads and
check for short or open between the terminals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate continuity
for a short time and should indicate an open circuit once the capacitor is charged. If the above is not
the case, check the capacitor with an ohmmeter to see if it is shorted between either of the terminals
and case. If it is shorted, replace the capacitor.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
CAVITY TEMPERATURE FUSE TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
A continuity check across the cavity temperature fuse terminals should indicate a closed circuit unless
the temperature of the cavity temperature fuse reaches approximately 302½F(150½C). An open
cavity temperature fuse indicates overheating of the oven, exchange the cavity temperature fuse and
check inside of oven cavity and for improper setting of cooking time or operation of control unit. Check
for restricted air flow through the vent holes of the oven cavity, especially the cooling fan and air guide.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
MAGNETRON TEMPERATURE FUSE TEST
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. A continuity check across the magnetron temperature fuse terminals should indicate a closed circuit
unless the temperature of the magnetron temperature fuse reaches approximately 302½F(150½C).
An open magnetron temperature fuse indicates overheating of the magnetron. Check for restricted
air flow to the magnetron, especially the cooling fan air guide.
13
DMO2420B
DMO2420R
DMO2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
CAUTION: IF THE TEMPERATURE FUSE INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE, REPLACE TEMPERATURE FUSE.
F
SECONDARY INTERLOCK SWITCH TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the secondary interlock switch.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
PRIMARY INTERLOCK SYSTEM TEST
DOOR SENSING SWITCH
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the door sensing switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the cooling fan,
turntable and oven light will be activated by RY1.
PRIMARY INTERLOCK RELAY (RY2)
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect two (2) wire leads from the male tab terminals of the Primary Interlock Relay. Check the
state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay contacts
are closed, replace the circuit board entirely or the relay itself.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
G
MONITOR SWITCH TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Before performing this test, make sure that the secondary interlock switch and the primary interlock
relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire lead
from the monitor switch (COM) terminal. Check the monitor switch operation by using the ohmmeter
as follows. When the door is open, the meter should indicate a closed circuit. When the monitor switch
actuator is pushed by a screw driver through the lower latch hole on the front plate of the oven cavity
14
DMO2420B
DMO2420R
DMO2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
5.
6.
7.
8.
with the door opened (in this condition the plunger of the monitor switch is pushed in), the meter should
indicate an open circuit. If improper operation is indicated, the switch may be defective. After testing
the monitor switch, reconnect the wire lead to the monitor switch (COM) terminal and check the
continuity of the monitor circuit.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Screw Driver
Reconnect the power supply
RED
cord after the outer case is
WHT/WHT
installed.
Run the oven and check all
functions.
Monitor
Switch
Ohmmeter
Secondary Interlock Switch
H
BLOWN MONITOR FUSE TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the monitor fuse is blown when the door is opened, check the primary interlock relay, secondary
interlock switch and monitor switch according to the "TEST PROCEDURE" for those switches before
replacing the blown monitor fuse.
CAUTION: BEFORE REPLACING A BLOWN MONITOR FUSE, TEST THE PRIMARY INTERLOCK
RELAY, SECONDARY INTERLOCK SWITCH, DOOR SENSING SWITCH AND MONITOR
SWITCH FOR PROPER OPERATION.
If the monitor fuse is blown by improper switch operation, the monitor fuse and monitor switch must
be replaced with "monitor fuse and monitor switch assembly" part number FFS-BA016/KIT, even if
the monitor switch operates normally. The monitor fuse and monitor switch assembly is comprised
of a 20 ampere fuse and switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
I
TOUCH CONTROL PANEL ASSEMBLY TEST
The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore,
unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter
and ohmmeter.
In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key
Unit, and also the Control Unit is divided into two units, LSI Unit and Power Unit, and troubleshooting by
unit replacement is described according to the symptoms indicated.
Before testing,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
1. Key Unit.
NOTE ;
1) Check Key unit ribbon connection before replacement.
2) Reconnect all leads removed from components during testing.
3) Re-install the outer case (cabinet).
15
DMO2420B
DMO2420R
DMO2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
4) Reconnect the power supply cord after the outer case is installed.
5) Run the oven and check all functions.
The following symptoms indicate a defective key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
If the Key unit is defective.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Replace the Key unit.
5) Reconnect all leads removed from components during testing.
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.
2. Control Unit
The following symptoms indicate a defective control unit. Before replacing the control unit, perform
the Key unit test (Procedure J) to determine if control unit is faulty.
2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) The figure of all digits flicker.
2-3 Other possible problems caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
When testing is completed,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Reconnect all leads removed from components during testing.
5) Re-install the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions.
J
KEY UNIT TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable
is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing switch
(stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and
make sure the door sensing switch is closed (either close the door or short the door sensing switch
connecter). Use the Key unit matrix indicated on the control panel schematic and place a jumper wire
between the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control
unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does
not respond, it is a faulty and must be replaced. If a specific pad does not respond, the above method
16
DMO2420B
DMO2420R
DMO2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
5.
6.
7.
8.
may be used (after clearing the control unit) to determine if the control unit or key pad is at fault.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
G1
FRESH
VEGETABLES
GROUND
MEAT
ENTREES
G2
G3
G4
G5
G6
G7
G8
BEVERAGE
1
2
3
4
5
G9
MICROWAVE
RECIPES
6
7
8
9
0
G10
START
INSTANT ON
TIMER
CLOCK
KEEP
WARM
SNACKS
EASY
MINUTE
G11
FISH
VEGETABLES SEAFOOD BREAKFAST
POWER
LEVEL
LUNCH
STOP
CLEAR
15
MINUTE
DINNER
G12
AUTO
DEFROST
HELP
GUIDE
BAKED
POTATOES
RICE
POULTRY
REHEAT POPCORN
G13
G14
K
RELAY TEST
2.
3.
4.
5.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the leads to the primary of the power transformer.
Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape.
6. After that procedure, re-connect the power supply cord.
7. Remove the outer case and check voltage between Pin No. 1 of the 2 pin connector (A) and the
common terminal of the relay RY1 on the control unit with an A.C. voltmeter.
The meter should indicate 120 volts, if not check oven circuit.
RY1 and RY2 Relay Test
These relays are operated by D.C. voltage
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.
DC. voltage indicated ......................... Defective relay.
DC. voltage not indicated .................... Check diode which is connected to the relay coil. If diode
is good, control unit is defective.
RELAY SYMBOL
OPERATIONAL VOLTAGE
CONNECTED COMPONENTS
RY1
Approx. 24.0V D.C.
Oven lamp / Turntable motor / Cooling fan motor
RY2
Approx. 23.0V D.C.
Power transformer
8.Disconnect the power supply cord, and then remove outer case.
9.Open the door and block it open.
10.Discharge high voltage capacitor.
11.Reconnect all leads removed from components during testing.
12.Re-install the outer case (cabinet).
13.Reconnect the power supply cord after the outer case is installed.
14.Run the oven and check all functions.
L
COMPU DEFROST TEST
WARNING : The oven should be fully assembled before following procedure.
(1) Place one cup of water in the center of the turntable tray in the oven cavity.
(2) Close the door, touch the Auto Defrost pad and touch the number pad 5. And touch the number pad
5 again. And then touch the Start pad.
(3) The oven is in Auto Defrost cooking condition.
(4) The oven will operate as follows.
17
DMO2420B
DMO2420R
DMO2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
MENU
Steaks, chops or fish
0.5lb
1ST STAGE
LEVEL
TIME
70%
30sec.
2ND STAGE
LEVEL
TIME
40%
15sec.
(5) If improper operation is indicated, the control unit is probably defective and should be checked.
M
FOIL PATTERN ON THE PRINTED WIRING BOARD TEST
To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary on
the PWB, this foil pattern acts as a fuse.
1. Foil pattern check and repairs.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Follow the troubleshooting guide given below for repair.
STEPS
OCCURRENCE
CAUSE OR CORRECTION
1
Only pattern at "a" is broken.
*Insert jumper wire J1 and solder.
2
Pattern at "a" and "b" are broken.
*Insert the coil RCILF2003YAZZ between "c" and "d".
T1
AC
1
VH
VRS1
2
CN - A
d
a
b
XA
5) Make a visual inspection of the varistor.
Check for burn damage and examine the
transformer with a tester for the presence
of layer short-circuit (check the primary
coil resistance which is approximately
210ý ± 15%). If any abnormal condition is
detected, replace the defective parts.
(J1)
c
OMIF
D U
6)
7)
8)
9)
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
2. Follow the troubleshooting guide given below, if indicator does not light up after above check and
repairs are finished.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
6) After that procedure, reconnect the power supply cord.
7) Follow the troubleshooting guide given below for repair.
STEPS
OCCURRENCE
CAUSE OR CORRECTION
1
The rated AC voltage is not present between
Pin No. 1 of the 2-pin connector (A) and the Check supply voltage and oven power cord.
common terminal of the relay RY1.
2
The rated AC voltage is present at primary
side of low voltage transformer.
Low voltage transformer or secondary circuit defective.
Check and repair.
8) Disconnect the power supply cord, and then remove outer case.
9) Open the door and block it open.
18
DMO2420B
DMO2420R
DMO2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
10) Discharge high voltage capacitor.
11) Reconnect all leads removed from components during testing.
12) Re-install the outer case (cabinet).
13) Reconnect the power supply cord after the outer case is installed.
14) Run the oven and check all functions.
N
AH SENSOR TEST
Checking the initial sensor cooking condition
WARNING : The oven should be fully assembled before following procedure.
(1) The oven should be plugged in at least two minutes before sensor cooking.
(2) Room temperature should not exceed 95½F (35½C).
(3) The unit should not be installed in any area where heat and steam are generated. The unit should not
be installed, for example, next to a conventional surface unit. Refer to the “INSTALLATION
INSTRUCTIONS” of the operation manual.
(4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To
permit adequate ventilation, be sure to install so as not to block these vents. There should be some
space for air circulation.
(5) Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any moisture
with a dry cloth or paper towel.
(6) The Sensor works with food at normal storage temperature. For example, chicken pieces would be
at refrigerator temperature and canned soup at room temperature.
(7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The
sensor will detect the vapor given of by the spray and turn off before food is properly cooked.
(8) If the sensor has not detected the vapor of the food, ERROR will appear and the oven will shut off.
Water load cooking test
WARNING : The oven should be fully assembled before following procedure.
Make sure the oven has been plugged in at least two minutes before checking sensor cook operation.
The cabinet should be installed and screws tightened.
(1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
(2) Place the container on the center of tray in the oven cavity.
(3) Close the door.
(4) Touch the Timer/Clock pad once, the Power Level pad twice, the Start pad once and the number pad
1 once. Now, the oven is in the sensor cooking condition and "TEST", “SENSOR” and "COOK" will
appear in the display.
(5) The oven will operate for the first 16 seconds, without generating microwave energy.
NOTE: ERROR will appear if the door is opened or STOP/CLEAR pad is touched during first stage of
sensor cooking.
(6) After approximately 16 seconds, microwave energy is produced.
If ERROR is displayed, replace the AH sensor or check the control unit, refer to explanation below.
If the oven stops after 5 minutes and ERROR is displayed, check the parts except for the AH sensor.
TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement sensor.
(1) Disconnect the power supply cord, and then remove outer case.
(2) Open the door and block it open.
(3) Discharge high voltage capacitor.
(4) Remove the AH sensor.
(5) Install the new AH sensor.
(6) Reconnect all leads removed from components during testing.
(7) Re-install the outer case (cabinet).
(8) Reconnect the power supply cord after the outer case is installed.
(9) Reconnect the oven to the power supply and check the sensor cook operation as follows:
9-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
9-2. Place the container on the center of tray in the oven cavity.
19
DMO2420B
DMO2420R
DMO2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
9-3. Close the door.
9-4. Touch the Timer/Clock pad once, the Power Level pad twice, the Start pad once and the number
pad 1 once.
9-5. The control panel is in automatic Sensor operation.
9-6. And then the oven will turn off automatically, and the time for detecting moisture will be displayed.
If new sensor dose not operate properly, the problem is with the control unit, and refer to explanation
below.
CHECKING CONTROL UNIT
(1) Disconnect the power supply cord, and then remove outer case.
(2) Open the door and block it open.
(3) Discharge high voltage capacitor.
(4) Disconnect the sensor connector that is mounted to control panel.
(5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel.
(6) Disconnect the leads to the primary of the power transformer.
(7) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
(8) After that procedure, re-connect the power supply cord.
(9) Check the sensor cook operation proceed as follows:
9-1. Touch the Timer/Clock pad once, the Power Level pad twice, the Start pad once and the number
pad 1 once.
9-2. The control panel is in the sensor cooking operation.
9-3. After approximately 25 seconds, push plunger of select switch for more than 3 seconds. This
condition is same as judgement by AH sensor.
9-4. After approximately 3 seconds, the oven will turn off automatically, and the display shows “ X
X . X X “ which is the time for detecting moisture.
If the above is not the case, the control unit is probably defective.
If the above is proper, the AH sensor is probably defective.
(10) Disconnect the power supply cord, and then remove outer case.
(11) Open the door and block it open.
(12) Discharge high voltage capacitor.
(13) Disconnect the dummy resistor circuit from the sensor connector of control panel.
(14) Carry out necessary repair.
(15) Reconnect all leads removed from components during testing and repairing.
(16) Re-install the outer case (cabinet).
(17) Reconnect the power supply cord after the outer case is installed. Run the oven and check all
functions.
(18) Carry out "Water load cooking test" again and ensure that the oven works properly.
R1, R2 :22((ohm) ± 1% 1/2W
R3 :4.3k((ohm) ± 5% 1/4W
R4 : 1M((ohm) ± 5% 1/4W
Plunger
NC
NO
F-1
F-2
To connector (F)
on Control Unit.
1
2
3
COM
COM
F-3
CONNECTOR
R2
R3
R4
Sensor Dummy Resistor Circuit
20
NO
R1
NC
DMO2420B
DMO2420R
DMO2420S
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
4) Relay Circuit
A circuit to drive the magnetron, fan motor, turntable
motor and light the oven lamp.
The touch control section consists of the following units.
(1) Key Unit
(2) Control Unit (The Control Unit consists of Power Unit
and LSI Unit).
5) Buzzer Circuit
The buzzer is responsive to signals from the LSI to emit
audible sounds (key touch sound and completion sound).
The principal functions of these units and the signals communicated among them are explained below.
6) Synchronizing Signal Circuit
The power source synchronizing signal is available in
order to compose a basic standard time in the clock
circuit.
It accompanies a very small error because it works on
commercial frequency.
Key Unit
The key unit is composed of a matrix, signals generated in
the LSI are sent to the key unit through P00-P07.
When a key pad is touched, a signal is completed through
the key unit and passed back to the LSI through P14-P17,
AIN6 and AIN7 to perform the function that was requested.
7) Door Sensing Switch
A switch to “tell” the LSI if the door is open or closed.
Control Unit
Control unit consists of LSI, ACL circuit, indicator circuit,
power source circuit, relay circuit, buzzer circuit, synchronizing signal circuit, absolute humidity sensor circuit and back
light circuit.
8) Back Light Circuit
A circuit to drive the back light (Light emitting diodes
LD10- LD15).
9) Absolute Humidity Sensor Circuit
This circuit detects moisture of the cooking food to allow
its automatic cooking.
1) ACL
This circuit generates a signal which resets the LSI to the
initial state when power is supplied.
2) Indicator Circuit
This circuit consists of 40 segments and 16 common
electrodes using a Liquid Crystal Display. The Liquid
Crystal Display (LCD) is drived by LCD driver IC3.
3) Power Source Circuit
This circuit generates voltages necessary in the control
unit from the AC line voltage.
In addition, the synchronizing signal is available in order
to compose a basic standard time in the clock circuit.
Symbol
Voltage
VC
-5V
Application
LSI(IC1)
21
DMO2420B
DMO2420R
DMO2420S
LSI(IXA098DR)
The I/O signal of the LSI(IXA098DR) is detailed in the following table.
Pin No.
Signal
I/O
Description
1
COM5
OUT
Common data signal : COM11.
Connected to LCD signal COM11.
2
COM4
OUT
Common data signal : COM12.
Connected to LCD signal COM12.
3
COM3
OUT
Common data signal : COM13.
Connected to LCD signal COM13.
4
COM2
OUT
Common data signal : COM14.
Connected to LCD signal COM14.
5
COM1
OUT
Common data signal : COM15.
Connected to LCD signal COM15.
6
COM0
OUT
Common data signal : COM16.
Connected to LCD signal COM16.
7-10
VL1-VL4
IN
Power source voltage input terminal.
Standard voltage for LCD.
11
VL5
IN
Power source voltage input terminal.
Standard voltage for LCD. Connected to GND.
12-14
C3-C1
IN
Terminal not used.
15
VLIN
IN
Terminal not used.
16
VREG
Terminal not used.
17
NC
OUT
_
18
VSS
IN
19-21
P27-P25
OUT
22-26
P24-P20
IN
Used for initial balancing of the bridge circuit (absolute humidity sensor).
27
P47
IN
To input signal which communicates the door open/close information to LSI.
Door close "H" level signal (0V). Door open "L" level signal (-5V).
28
P46
OUT
Terminal not used.
29
P45
OUT
Oven lamp, fan motor and turntable motor driving signal.
16.7 msec.
To turn on and off shut off relay (RY1). The
square waveform voltage is delivered to the
RY1 driving circuit and RY2 control circuit.
Terminal not used.
Power source voltage : -5.0V.
The power source voltage to the LSI is input to VSS terminal. Connected to VC.
Terminal not used.
H : GND
L : -5V
During cooking
30
P44
OUT
Magnetron high-voltage circuit driving signal.
To turn on and off the cook relay (RY2). The
OFF
signals holds "L" level during microwave cook100
ing and "H" level while not cooking. In other
PERCENT
cooking modes (variable cooking) the signal
OFF
turns to "H" level and "L" level in repetition
70
according to the power level.
PERCENT
H : GND
ON
L : -5V
OFF
24 sec.
ON
H : GND
8 sec.
L : -5V
(ON and OFF times for other power level.)
31
P43
OUT
Terminal not used.
32
CNTR0
OUT
Signal to sound buzzer (2.0 kHz).
A: key touch sound.
B: Completion sound.
0.1 sec.
H : GND
A
2.0 sec.
L : -5V
H : GND
B
L : -5V
33
P41
OUT
Terminal not used.
22
DMO2420B
DMO2420R
DMO2420S
Pin No.
34
Signal
INT0
I/O
IN
Description
Signal synchronized with commercial power source frequency.
This is the basic timing for time processing of LSI.
H : GND
L : -5V
16.7 msec.
35
P07
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and
P17 terminal while one of G1 line keys on key matrix is touched.
36
P06
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and
P17 terminal while one of G2 line keys on key matrix is touched.
37
P05
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and
P17 terminal while one of G3 line keys on key matrix is touched.
38
P04
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and
P17 terminal while one of G4 line keys on key matrix is touched.
39
P03
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and
P17 terminal while one of G5 line keys on key matrix is touched.
40
P02
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AIN6, AIN7, P14, P15, P16
and P17 terminal while one of G6 line keys on key matrix is touched.
41
P01
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and
P17 terminal while one of G7 line keys on key matrix is touched.
42
P00
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and
P17 terminal while one of G8 line keys on key matrix is touched.
43
P17
OUT
Signal coming from touch key.
When either G9 line on key matrix is touched, a corresponding signal out of P00-P07 will
be input into P17. When no key is touched, the signal is held at "H" level.
44
P16
IN
Signal similar to P17.
When either G10 line on key matrix is touched, a corresponding signal will be input into P16.
45
P15
IN
Signal similar to P17.
When either G11 line on key matrix is touched, a corresponding signal will be input into P15.
46
P14
IN
Signal similar to P17.
When either G12 line on key matrix is touched, a corresponding signal will be input into P14.
47
AIN7
IN
Signal similar to P17.
When either G13 line on key matrix is touched, a corresponding signal will be input into AIN7.
48
AIN6
IN
Input terminal to judge the model.
The signal out of P02 will be input into AIN6 through G6 line on key matrix. The LSI will
judge the model by this signal.
49
AIN5
IN
AH sensor input.
This input is an analog input terminal from the AH sensor circuit, and connected to the
A/D converter built into the LSI.
50
AIN4
IN
Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is an
analog input terminal from the AH sensor circuit, and connected to the A/D converter built
into the LSI.
51
RESET
IN
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily set
"L" level the moment power is applied, at this time the LSI is reset. Thereafter set at "H"
level
23
DMO2420B
DMO2420R
DMO2420S
Pin No.
Signal
NC
I/O
_
52
Description
Terminal not used.
53
XCOUT
OUT
Terminal not used.
54
XCIN
Connected to VC.
55
NC
IN
_
56
VCC
IN
Power source voltage: GND(0V).
The power source voltage to drive LSI is input to VCC terminal.
57
OSCSEL
IN
Connected to VC(-5V).
58
XOUT
OUT
59
VSS
IN
60
NC
61
XIN
IN
Internal clock oscillation frequency control input setting.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit with
respect to XOUT terminal.
62
NC
_
Terminal not used.
63-66
AIN3-AIN0
IN
Terminal to change cooking input according to the Model.
By using the A/D converter contained in the LSI, DC voltage in accordance with the Model
in operation is applied to set up its cooking constant.
67
COM8
OUT
Common data signal : COM8. Connected to LCD signal COM8.
68
COM9
OUT
Common data signal : COM7. Connected to LCD signal COM7.
69
COM10
OUT
Common data signal : COM6. Connected to LCD signal COM6.
70
COM11
OUT
Common data signal : COM5. Connected to LCD signal COM5.
71
COM12
OUT
Common data signal : COM4. Connected to LCD signal COM4.
72
COM13
OUT
Common data signal : COM3. Connected to LCD signal COM3.
73
COM14
OUT
Common data signal : COM2. Connected to LCD signal COM2.
74
COM15
OUT
Common data signal : COM1. Connected to LCD signal COM1.
75-102
SEG67-SEG40
OUT
Terminal not used.
103-142
SEG39-SEG0
OUT
Segment data signal.
Connected to LCD.
The relation between signals and LCD are as follows:
LSI signal (Pin No.)
LCD segment
LSI signal (Pin No.)
LCD segment
SEG 39 (103) .......................... SEG 1
SEG 19 (123) ......................... SEG 21
SEG 38 (104) .......................... SEG 2
SEG 18 (124) ......................... SEG 22
SEG 37 (105) .......................... SEG 3
SEG 17 (125) ......................... SEG 23
SEG 36 (106) .......................... SEG 4
SEG 16 (126) ......................... SEG 24
SEG 35 (107) .......................... SEG 5
SEG 15 (127) ......................... SEG 25
SEG 34 (108) .......................... SEG 6
SEG 14 (128) ......................... SEG 26
SEG 33 (109) .......................... SEG 7
SEG 13 (129) ......................... SEG 27
Terminal not used.
Internal clock oscillation output.
Output to control oscillation input of XIN.
Power source voltage: -5.0V.
The power source voltage to the LSI is input to VSS terminal. Connected to VC.
Terminal not used.
SEG 32 (110) .......................... SEG 8
SEG 31 (111) .......................... SEG 9
SEG 30 (112) .......................... SEG 10
SEG 29 (113) .......................... SEG 11
SEG 28 (114) .......................... SEG 12
SEG 27 (115) .......................... SEG 13
SEG 26 (116) .......................... SEG 14
SEG 25 (117) .......................... SEG 15
SEG 24 (118) .......................... SEG 16
SEG 23 (119) .......................... SEG 17
SEG 22 (120) .......................... SEG 18
SEG 21 (121) .......................... SEG 19
SEG 20 (122) .......................... SEG 20
24
SEG 12 (130) ......................... SEG 28
SEG 11 (131) ......................... SEG 29
SEG 10 (132) ......................... SEG 30
SEG 9 (133) ......................... SEG 31
SEG 8 (134) ......................... SEG 32
SEG 7 (135) ......................... SEG 33
SEG 6 (136) ......................... SEG 34
SEG 5 (137) ......................... SEG 35
SEG 4 (138) ......................... SEG 36
SEG 3 (139) ......................... SEG 37
SEG 2 (140) ......................... SEG 38
SEG 1 (141) ......................... SEG 39
SEG 0 (142) ......................... SEG 40
DMO2420B
DMO2420R
DMO2420S
Pin No.
Signal
I/O
Description
143
COM7
OUT
Common data signal : COM9. Connected to LCD signal COM9.
144
COM6
OUT
Common data signal : COM10.
Connected to LCD signal COM10.
ABSOLUTE HUMIDITY SENSOR CIRCUIT
LSI are turned on in such a way as to change the
resistance values in parallel with R98 ~ R102. Changing
the resistance values results in that there is the same
potential at both F-3 terminal of the absolute humidity
sensor and AIN4 terminal of the LSI. The voltage of AIN5
terminal will indicate about -2.5V. This initial balancing is
set up about 16 seconds after the unit is put in the Sensor
Cooking mode. As the sensor cooking proceeds, the
food is heated to generate moisture by which the
resistance balance of the bridge circuit is deviated to
increase the voltage available at AIN5 terminal of the LSI.
Then the LSI observes that voltage at AIN5 terminal and
compares it with its initial value, and when the comparison
rate reaches the preset value (fixed for each menu to be
cooked), the LSI causes the unit to stop sensor cooking;
thereafter, the unit goes in the next operation automatically.
When the LSI starts to detect the initial voltage at AIN5
terminal 16 seconds after the unit has been put in the
Sensor Cooking mode, if it is not possible to balance the
bridge circuit due to disconnection of the absolute humidity
sensor, ERROR will appear on the display and the
cooking is stopped.
(1) Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed in
the closed vessel filled with dry air while another in the
open vessel. Each sensor is provided with the protective
cover made of metal mesh to be protected from the
external airflow.
ventilation opening for sensing
(2) Operational Principle of Absolute Humidity Sensor
The figure below shows the basic structure of an absolute
humidity sensor. A bridge circuit is formed by two
thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
Each thermistor is supplied with a current to keep it
heated at about 150½C (302½F), the resultant heat is
dissipated in the air and if the two thermistors are placed
in different humidity conditions they show different degrees
of heat conductivity leading to a potential difference
between them causing an output voltage from the bridge
circuit, the intensity of which is increased as the absolute
humidity of the air increases. Since the output is very
minute, it is amplified by the operational amplifier.
300k
25
R100
150k
24
R101
75k
23
R102
37.4k
22
C. Thermistor in
closed vessel
S. Thermistor in
open vessel
R97
50
Absolute humidity (g/m 2 )
S
(3) Detector Circuit of Absolute Humidity Sensor Circuit
This detector circuit is used to detect the output voltage
of the absolute humidity circuit to allow the LSI to control
sensor cooking of the unit. When the unit is set in the
sensor cooking mode, 16 seconds clearing cycle occurs
than the detector circuit starts to function and the LSI
observes the initial voltage available at its AIN5 terminal.
With this voltage given, the switches SW1 to SW5 in the
R90
F-2
R91
3.32k R92
1.8k
VA : -15V
25
8 7 6 5
1 2 3 4
R94
R95
10k
47k
R93
360k
D91
VA : -15V
VC : -5V
IC2
P21
P22
P23
P24
D90
SW2
SW3
SW4
SW5
AIN4
0.01uF
F-1
C
R96
F-3
3.57k
0.015uF
47k
C93
Absolute humidity vs,
output voltage characteristic
0.01uF
S : Thermistor
open vessel
C : Thermistor
closed vessel
R99
SW1
P20
LSI
(IC1)
C92
R3
R2
Operational
amplifier
Output
voltage
+
26
C91
S
R1
620k
R98
Output voltage
C
1) Absolute humidity sensor circuit
0.1
uF
Sensing part
(Closed vessel)
C90
Thermistors
Sensing part
(Open vessel)
49
AIN5
DMO2420B
DMO2420R
DMO2420S
TOUCH CONTROL PANEL SERVICING
4) Re-install the outer case (cabinet).
5) Re-connect the power supply cord after the outer
case is installed.
6) Run the oven and check all functions.
A. On some models, the power supply cord between the
touch control panel and the oven itself is so short that the
two can’t be separated. For those models, check and
repair all the controls (sensor-related ones included) of
the touch control panel while keeping it connected to the
oven.
B. On some models, the power supply cord between the
touch control panel and the oven proper is long enough
that they may be separated from each other. For those
models, it is possible to check and repair the controls of
the touch control panel while keeping it apart from the
oven proper; in this case you must short both ends of the
door sensing switch (on PWB) of the touch control panel
with a jumper, which activates an operational state that
is equivalent to the oven door being closed. As for the
sensor-related controls of the touch control panel,
checking them is possible if dummy resistor(s) with
resistance equal to that of the controls are used.
(2) Servicing the touch control panel with power supply
from an external power source:
Disconnect the touch control panel completely from the
oven proper, and short both ends of the door sensing
switch (on PWB) of the touch control panel, which
activates an operational state that is equivalent to the
oven door being closed. Connect an external power
source to the power input terminal of the touch control
panel, then it is possible to check and repair the controls
of the touch control panel it is also possible to check the
sensor-related controls of the touch control panel by
using the dummy resistor(s).
1. Precautions for Handling Electronic Components
This unit uses CMOS LSI in the integral part of the
circuits. When handling these parts, the following
precautions should be strictly followed. CMOS LSI have
extremely high impedance at its input and output terminals.
For this reason, it is easily influenced by the surrounding
high voltage power source, static electricity charge in
clothes, etc. and sometimes it is not fully protected by the
built-in protection circuit.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them in
aluminium foil. Also wrap all PW boards containing them
in aluminium foil.
2) When soldering, ground the technician as shown in the
figure and use grounded soldering iron and work table.
approx. 1M ohm
2. Shapes of Electronic Components
Transistor
2SB1238
Transistor
KRC243M
3. Servicing of Touch Control Panel
We describe the procedures to permit servicing of the
touch control panel of the microwave oven and the
precautions you must take when doing so. To perform
the servicing, power to the touch control panel is available
either from the power line of the oven itself or from an
external power source.
(1) Servicing the touch control panel with power supply
of the oven:
CAUTION:
THE HIGH VOLTAGE TRANSFORMER OF THE
MICROWAVE OVEN IS STILL LIVE DURING
SERVICING AND PRESENTS A HAZARD.
Therefore, before checking the performance of the touch
control panel,
1) Disconnect the power supply cord, and then remove
outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power
transformer.
5) Ensure that these leads remain isolated from other
components and oven chassis by using insulation
tape.
6) After that procedure, re-connect the power supply
cord.
After checking the performance of the touch control
panel,
1) Disconnect the power supply cord.
2) Open the door and block it open.
3) Re-connect the leads to the primary of the power
transformer.
4. Servicing Tools
Tools required to service the touch control panel
assembly.
1) Soldering iron: 30W
(It is recommended to use a soldering iron with a grounding
terminal.)
2) Oscilloscope: Single beam, frequency range: DC-10MHz
type or more advanced model.
3) Others: Hand tools
5. Other Precautions
1) Before turning on the power source of the control unit,
remove the aluminium foil applied for preventing static
electricity.
2) Connect the connectors of the key unit to the control unit
being sure that the lead wires are not twisted.
3) After aluminium foil is removed, be careful that abnormal
voltage due to static electricity etc. is not applied to the
input or output terminals.
4) Attach connectors, electrolytic capacitors, etc. to PWB,
making sure that all connections are tight.
5) Be sure to use specified components where high precision
is required.
26
DMO2420B
DMO2420R
DMO2420S
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
WARNING AGAINST HIGH VOLTAGE:
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may
result in severe, possibly fatal, electric shock.
(Example)
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
WARNING:
Avoid possible exposure to microwave energy. Please follow the instructions below before operating
the oven.
1. Disconnect the power supply cord.
2. Make sure that a definite” click” can be heard when the
microwave oven door is unlatched. (Hold the door in a
closed position with one hand, then push the door open
button with the other, this causes the latch leads to rise,
it is then possible to hear a “click’ as the door switches
operate.)
3. Visually check the door and cavity face plate for damage
(dents, cracks, signs of arcing etc.).
1.
2.
3.
4.
5.
6.
Door does not close firmly.
Door hinge, support or latch hook is damaged.
The door gasket or seal is damaged.
The door is bent or warped.
There are defective parts in the door interlock system.
There are defective parts in the microwave generating
and transmission assembly.
7. There is visible damage to the oven.
Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
WARNING FOR WIRING
To prevent an electric shock, take the following precautions.
1. Before wiring,
1) Disconnect the power supply cord.
2) Open the door block it open.
3) Discharge the high voltage capacitor and wait for 60
seconds.
2. Don’t let the wire leads touch to the following parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, High voltage transformer and
Oven cavity.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector until its pin is locked
and make sure that the wire leads do not come off even
if the wire leads are pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS’, when carrying out any of
the following removal procedures:
OUTER CASE REMOVAL
To remove the outer case, proceed as follows.
1. Disconnect the power supply cord.
2. Open the oven door and block it open.
3. Remove the two (2) screws from the lower portion of the
rear cabinet using a T20H Torx type or GTXH20-100
screw driver.
4. Remove the remaining two (2) screws from rear and four
(4) screws along the right side of outer case.
5. Slide the entire outer case back out about 1 inch (3 cm)
to free it from retaining clips on the cavity face plate.
6. Lift entire outer case from the unit.
27
DMO2420B
DMO2420R
DMO2420S
CAUTION: 1. DISCONNECT OVEN FROM POWER SUP
PLY BEFORE REMOVING OUTER CASE.
2. DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN
COMPONENTS OR WIRING.
NOTE: When replacing the outer case, the 2 special
Torx screws must be reinstalled in the same
locations.
Special screw
Screw Driver
(Type: TORX T20 H or
GTXH20-100)
POWER TRANSFORMER REMOVAL
1. Disconnect the power supply cord and then remove outer
case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads (primary and high voltage) from
power transformer and the filament leads from the
magnetron and capacitor terminals.
5. Remove four (4) screws holding transformer to bottom
plate.
6. Remove transformer from bottom plate.
Reinstallation
1. Rest transformer on the bottom plate with its primary
terminals toward the oven face plate.
2. Secure transformer with four screws to bottom plate.
3. Re-connect wire leads (primary and high voltage) to
power transformer and filament leads of transformer to
magnetron and high voltage capacitor. Refer to
"PICTORIAL DIAGRAM" on page 35.
4. Re-install outer case and check that oven is operating
properly.
HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL
1. Disconnect the power supply cord and then remove outer
case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the high voltage wire A from the high voltage
capacitor.
5. Disconnect the high voltage wire of high voltage rectifier
assembly from the magnetron.
6. Disconnect the filament lead (short one) of the power
transformer from the high voltage capacitor.
7. Remove one (1) screw holding capacitor holder with the
high voltage rectifier to the base plate.
8. Disconnect rectifier terminal from capacitor.
High voltage rectifier assembly is now free.
9. Remove capacitor holder. Capacitor is now free.
CAUTION: WHEN REPLACING HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR,
GROUND SIDE TERMINAL OF THE HIGH
VOLTAGE RECTIFIER MUST BE SECURED
FIRMLY WITH A GROUNDING SCREW.
MAGNETRON REMOVAL
Removal
1. Disconnect the power supply cord and then remove outer
case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads from magnetron.
5. Remove the two (2) screws holding the chassis support
to the magnetron and the oven cavity front flange.
6. Slide the magnetron duct slightly so that the two (2)
screws at left hand side of the magnetron appear.
7. Carefully remove the four (4) screws holding magnetron
to waveguide flange.
8. Remove the magnetron with care so that the magnetron
antenna is not hit by any metal object around the antenna.
9. Now, the magnetron is free.
Reinstallation
1. Re-install the magnetron to waveguide flange with care
to prevent damage to the magnetron antenna.
2. Secure the magnetron with the four (4) screws.
3. Hold the chassis support to the oven cavity front plate and
the magnetron with the two (2) screws.
4. Reconnect the wire leads to the magnetron. Refer to
"PICTORIAL DIAGRAM" on page 35.
5. Re-install outer case and check that the oven is operating
properly.
CAUTION: WHEN REPLACING MAGNETRON, BE SURE
THE R.F. GASKET IS IN PLACE AND MOUNTING SCREWS ARE TIGHTENED SECURELY
28
DMO2420B
DMO2420R
DMO2420S
OVEN LAMP AND LAMP SOCKET REMOVAL
1.
2.
3.
4.
5.
Disconnect the power supply cord and remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Remove the oven lamp from the oven lamp socket.
Pull the wire leads from the oven lamp socket by pushing
the terminal hole of the oven lamp socket with the small
flat type screw driver.
6. Remove the oven lamp socket from the magnetron duct
by turning the socket counterclockwise.
7. Remove the oven lamp from the socket by turning the
oven lamp.
8. Now, the oven lamp and the oven lamp socket are free.
Oven lamp
socket
Terminal
Wire lead
Terminal hole
Flat type small
screw driver
Figure C-1. Oven lamp socket
POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL
Terminal
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock® connector.
5. Pull down on the positive lock® connector.
Positive lock®
connector
1
Push
Lever
CAUTION: WHEN CONNECTING THE POSITIVE LOCK®
CONNECTORS TO THE TERMINALS, CONNECT THE POSITIVE LOCK® SO THAT THE
LEVER FACES YOU.
2
Pull down
Figure C-2. Positive lock® connector
CONTROL PANEL ASSEMBLY REMOVAL
3. Stick the key unit firmly to the control panel frame
by rubbing with soft cloth so not to scratch.
1. Disconnect the power supply cord and then remove outer
case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from panel components.
5. Make one (1) tab of the oven cavity front plate straight
holding the control panel assembly to the oven cavity
front plate.
6. Slide the control panel assembly upward and remove it.
7. Now, individual components can be removed.
NOTE: 1. Before attaching a new key unit, wipe off remaining
adhesive on the control panel frame surfaces
completely with a soft cloth soaked in alcohol.
2. When attaching the key unit to the control panel
frame, adjust the upper edge and right edge of the
key unit to the correct position of control panel
frame.
LSI UNIT
NOTE: Handle the LSI unit carefully so that there is no
excessive force applied to the ribbon connection.
Liquid Crystal
Display (LCD)
Printed wiring board
of LSI unit
Ribbon cable
LSI unit
TURNTABLE MOTOR REMOVAL
5. Disconnect wire leads from turntable motor.
(See "Positive lock connector removal")
6. Remove one (1) screw holding turntable motor to oven
cavity.
7. Now the turntable motor is free.
8. After replacement use the one (1) screw to fit the turntable
motor cover.
1. Disconnect the power supply cord.
2. Remove turntable and turntable support from oven cavity.
3. Lay the oven on it's backside. Remove the turntable
motor cover by snipping off the material in four corners.
4. Where the corners have been snipped off bend corner
areas flat. No sharp edges must be evident after removal
of the turntable motor cover.
29
DMO2420B
DMO2420R
DMO2420S
COOLING FAN MOTOR REMOVAL
CAUTION:
* Do not reuse the removed fan blade because the hole
(for shaft) may be larger than normal.
REMOVAL
1. Disconnect the power supply cord and then remove outer
case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the fan motor.
5. Remove the two (2) screws holding the fan motor to the
oven cavity back plate.
6. Remove the fan blade from the fan motor shaft according
to the following procedure.
7. Hold the edge of the rotor of the fan motor by using a pair
of groove joint pliers.
CAUTION:
* Make sure that no metal pieces enter the gap between
the rotor and the stator of the fan motor because the
rotor is easily shaven by pliers and metal pieces may
be produced.
* Do not touch the pliers to the coil of the fan motor
because the coil may be cut or damaged.
* Do not disfigure the bracket by touching with the
pliers.
8. Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
9. Now, the fan blade and the fan motor will be free.
INSTALLATION
1. Install the fan blade to the fan motor shaft according to the
following procedure.
2. Hold the center of the bracket which supports the shaft of
the fan motor on the flat table.
3. Apply the screw lock tight into the hole (for shaft) of the
fan blade.
4. Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
CAUTION:
* Do not hit the fan blade hard when installing because
the bracket may be damaged.
* Make sure that the fan blade rotates smoothly after
installation.
* Make sure that the axis of the shaft is not slanted.
5. Install the fan motor to the the oven cavity back plate with
the two (2) screws.
6. Connect the wire leads to the fan motor, referring to the
pictorial diagram.
Coil
Shaft
Groove joint pliers
Shaft
Axis
Stator
Gap
Bracket
Rotor
These are the positions
that should be pinched
with pliers
Stator
Table
Center of
bracket
Rotor
Rear View
Side View
AH SENSOR REPLACEMENT
Removal
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the two (2) screws holding the AH sensor to the
sensor duct.
5. Disconnect the AH sensor harness from the connector
CN-F on control unit.
6. AH sensor is now free.
Reinstallation
1. Insert the new AH sensor into the sensor duct.
2. Install two (2) screws to secure the AH sensor.
3. Route the AH sensor harness across the oven cavity top
plate and through the large opening.
4. Connect the AH sensor harness to CN-F on control unit.
5. Re-install the outer case cabinet and check for proper
operation.
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
1.
2.
3.
4.
5.
6.
7. Push outward on the two (2) retaining tabs holding switch
in place.
8. Switch is now free.
At this time switch lever will be free, do not lose it.
Reinstallation
1. Re-install each switch in its place. The secondary interlock/
Disconnect the power supply cord and remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect wire leads from the switches.
Remove two (2) screws holding latch hook to oven flange.
Remove latch hook assembly from oven flange.
30
DMO2420B
DMO2420R
DMO2420S
monitor switches are in the lower position and the door
sensing switch is in the upper position.
2. Re-connect wire leads to each switch.
Refer to pictorial diagram.
3. Secure latch hook (with two (2) mounting screws) to oven
flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit. Refer to
chapter "Test Procedure" and Adjustment procedure.
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
If the door sensing switch, secondary interlock switch and
monitor switch do not operate properly due to a
misadjustment, the following adjustment should be made.
4. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
5. With door closed, adjust latch hook by moving it back and
forth, and up and down. In and out play of the door
allowed by the upper and lower position of the latch hook
should be less than 0.5mm. The vertical position of the
latch hook should be adjusted so that the door sensing
switch and secondary interlock switch are activated with
the door closed. The horizontal position of the latch hook
should be adjusted so that the plunger of the monitor
switch is pressed with the door closed.
6. Secure the screws with washers firmly.
7. Check the operation of all switches. If each switch has not
activated with the door closed, loosen screw and adjust
the latch hook position.
pushing and pulling lower portion of the door toward the
oven face. Both results (play in the door) should be less
than 0.5mm.
2. The door sensing switch and secondary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Latch Heads
Door Sensing
Switch
Door
Monitor Switch
Switch Lever
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm when in
the latched position. First check upper position of latch
hook, pushing and pulling upper portion of door toward
the oven face. Then check lower portion of the latch hook,
Secondary Interlock
Switch
Figure C-3. Latch Switch Adjustments
DOOR REPLACEMENT
REMOVAL
1. Disconnect the power supply cord.
2. Push the open button and open the door slightly.
3. Insert a putty knife (thickness of about 0.5mm) into the
gap between the choke cover and door frame as shown
in Figure C-4 to free engaging parts.
4. Pry the choke cover by inserting a putty knife as shown
in Figure C-4.
5. Release choke cover from door panel.
6. Now choke cover is free.
NOTE: When carrying out any repair to the door, do not
bend or warp the slit choke (tabs on the door
panelassembly) to prevent microwave leakage.
7. Release two (2) pins of door panel from two (2) holes of
upper and lower oven hinges by lifting up.
8. Now, door panel with door frame is free from oven cavity.
Choke Cover
Door Frame
Putty Knife
Figure C-4. Door Disassembly
9. Release the door panel from ten (10) tabs of door frame.
10.Remove the door panel from the door frame.
11.Now, door panel with sealer film is free.
12.Tear sealer film from door panel.
31
DMO2420B
DMO2420R
DMO2420S
Note:
13.Now, door panel is free.
14.Slide latch head upward and remove it from door frame
by releasing latch spring from door frame and latch head.
15.Now, latch head and latch spring are free.
16.Remove one (1) screw holding the door glass stopper to
the door frame.
17.Remove door glass stopper from door frame.
18.Slide the door glass rightwards and then slide upwards to
release the door glass from the tabs holding it.
19.Remove the door glass from the door frame.
20.Now, door frame is free.
REINSTALLATION
1. Re-install door glass to door frame as follows.
1-1. Insert the upper edge of the door glass into the five (5)
tabs of the door frame.
1-2. Slide the door glass downwards and insert the lower
edge of door glass into the five (5) tabs of the door
frame.
1-3. Slide the door glass leftwards and insert the left edge
of door glass into the two (2) tabs of the door frame.
2. Re-install the door glass stopper to the door frame so that
the two (2) holes of the door glass stopper fit to the two
(2) pins of the door frame. And hold the door glass
stopper with one (1) screw.
3. Re-install the latch spring to the latch head. Re-install the
latch spring to the door frame. Re-install latch head to
door frame.
4. Re-install door panel to door frame by catching ten (10)
tabs of door frame on the edges of door panel.
5. Put sealer film on door panel. Refer to “Sealer Film” about
how to handle new one.
6. Catch two (2) pins of door panel on two (2) hole of upper
and lower oven hinges.
7. Re-install choke cover to door panel by pushing.
Note: After any service to the door;
(A) Make sure that door sensing switch and secondary
interlock switch are operating properly. (Refer to
chapter “Test Procedures”.).
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
After any service, make sure of the following :
1. Door latch heads smoothly catch latch hook through
latch holes and that latch head goes through center of
latch hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Check for microwave leakage around door with an
approved microwave survey meter. (Refer to Microwave
Measurement Procedure.)
The door on a microwave oven is designed to act as
an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
cycle. This function does not require that door be airtight, moisture (condensation)-tight or light-tight.
Therefore, occasional appearance of moisture, light
or sensing of gentle warm air movement around
oven door is not abnormal and do not of themselves
indicate a leakage of microwave energy from oven
cavity.
Pin
Upper
Oven Hinge
Upper Oven
Hinge
Lower
Oven Hinge
Lower Oven
Hinge
Pin
Choke Cover
Figure C-5. Door Replacement
SEALER FILM
Installation
1. Put the adhesive tape on the backing film of the sealer
film as shown in Fig. C-6.
2. Tear the backing film by pulling the adhesive tape.
3. Put the pasted side of the sealer film on the door panel
Sealer film
Backing film
Adhesive tape
Figure C-6. Sealer film
32
1
RED
RED
A
WHT
CN-F
1 BLK
2 RED
3 WHT
MAGNETRON TEMP. FUSE
WHT
B
C
D
E
F
G
H
1
CAVITY TEMP. FUSE
NOTE:
The grounding conductor of
the power supply cord has
been grounded by power
supply cord fixing screw.
The screw must always be
kept tight.
RED
H
N
WHT
AH SENSOR
GRY
POWER SUPPLY
CORD 120V 60Hz
2
2
DOOR
SENSING
SWITCH
CONTROL PANEL
N.O.
PNK
COM.
(LSI UNIT)
to Oven cavity
CN-F
CN-G
NOTE:
The neutral (WHT/GRY) wire must
be connected to the terminal with
"N" mark on the power supply
cord.
GRN
GRN
WHT
CN-C
GRN
ORG
3
3
ORG
ORG
WHT
RY2
33
BRN
BLUE MARK
2 GRN
1 PNK
CN-B
NOTE:
Hot (ORG) wire must be
connected to the terminal
with blue mark on the oven
light socket.
CN-B
1 WHT
N.O.
1
2
2
FAN MOTOR
CN-A
T1
CN-A
HIGH VOLTAGE COMPONENTS
ORG
N.O.
B LU
4
4
BLK
1
COM.
RED
RED
(POWER UNIT)
PRIMARY
INTERLOCK
RELAY
BLU
OVEN LAMP
AND SOCKET
WHT
RED
WHT
N.C.
RED
COM.
MONITOR
FUSE
&
HOLDER
TURNTABLE
MOTOR
MAGNETRON
HIGH VOLTAGE
WIRE A
5
5
MONITOR
SWITCH
BLK
BRN
WHT
SECONDARY NO
INTERLOCK
SWITCH
COM.
WHT
WHT
WHT
WHT
GRY
HIGH
VOLTAGE
CAPACITOR
RED
WHT
POWER
TRANSFORMER
H.V. RECTIFIER
6
6
A
B
C
D
E
F
G
H
DMO2420B
DMO2420R
DMO2420S
Figure S-1. Pictorial Diagram
DMO2420B
DMO2420R
DMO2420S
2
1
4
3
6
5
A
A
B
B
CN-C
12PIN LEAD
WIRE HARNESS
Q2 2SB1238
R4 27
C
D2
b
+
–
D
LED
C2
GND
C3
VC
C1
VA
C4
INT
C9
VR
C
+
–
C4 10µ/35v
D4
1SS270A
C3 0.1µ/50v
6
1SS270A
ZD1
HZ16-1
3
d
a
D1
D3
C10
R5 4.7k
R1 2.4k
A2
4
C2 1000µ/35v
1
A1
10G471K
AC
VRS1
CN-A
D6
C1 0.1µ/50v
D1-D4
11ES1
T1
D5
D
R3 510 1/2w
(J1)
Q1 2SB1238
R2 680 1/2w
c
SP1 PKM22EPT
RY1
E
COM
D7
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
Q3 KRC243M
C5
BUZZER
C6
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
C7
MICRO
C8
NC
B2
C11
NC
B2
C12
DOOR
SENSING
SWITCH
NO
R6 3.3k
+
–
NO
D8
MICRO
COM
DOOR
SENSING
SWITCH
1SS270A
RY2
F
C5 10µ/35v
AC
1SS270A
E
G
F
G
H
H
Figure S-2. Power Unit Circuit
1
2
4
3
34
5
6
A
B
C
D
E
F
G
H
P20
P21
P22
R101
75kF
P23
R15
4.7k
(J16)
COM16
COM15
COM14
COM13
COM12
COM11
COM10
COM9
SEG40
SEG39
SEG38
SEG37
SEG36
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG9
SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
R18 R17 R16
4.7k 4.7k 4.7k
R19
4.7k
AIN3
(J17) 4.7k
(J14)
AIN2
(J15) 4.7k
(J10)
(J12)
AIN1
(J11) 4.7k
36
R40
4.7k
F-3
GROUND
MEAT
ENTREES
RICE
9
0
G10
KEEP
WARM
SNACKS
EASY
MINUTE
G11
STOP
CLEAR
15
MINUTE
DINNER
G12
POULTRY
FISH
VEGETABLES SEAFOOD BREAKFAST
POWER
LEVEL
LUNCH
AUTO
DEFROST
HELP
GUIDE
BAKED
POTATOES
REHEAT POPCORN
R79 270k
8
R78 270k
7
TIMER
CLOCK
R77 270k
6
START
INSTANT ON
MICROWAVE
RECIPES
R76 270k
G9
R74 270k
5
R75 270k
G8
4
C65 330p/50v
G7
3
C64 330p/50v
G6
2
C63 330p/50v
G5
1
C62 330p/50v
R67 15k
G4
COM8
SEG39
COM15
R68 15k P17
5
G3
BEVERAGE
5
FRESH
VEGETABLES
73
72
CF1
CST4.00MGW
P00
R66 15k
P01
R65 15k
P02
R64 15k
R63 15k
R62 15k
P03
C61 330p/50v
G2
P04
C60 330p/50v
G1
P05
R61 15k
: IF NOT SPECIFIED 1/10W ± 5%
R60 15k
NOTE
P06
108
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
SEG41
SEG42
SEG43
SEG44
SEG45
SEG46
SEG47
SEG48
SEG49
SEG50
SEG51
SEG52
SEG53
SEG54
SEG55
SEG56
SEG57
SEG58
SEG59
SEG60
SEG61
SEG62
SEG63
SEG64
SEG65
SEG66
SEG67
COM15
COM14
IC-1
IXA098DR
CN-F
P07
109
4
4
F-2
37
C40 0.01µ/25v
R41 15k
SEG34
COM5
C92
0.01µ/25v
P24
D40 1SS355
COM6
COM7
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
R95
15k
AIN5
COM5
COM4
COM3
COM2
COM1
COM0
VL1
VL2
VL3
VL4
VL5
C3
C2
C1
VLIN
VREG
NC
VSS
P27
P26
P25
P24
P23
P22
P21
P20
P47
P46
P45
P44
P43
CNTR0
P41
INT0
P07
P06
R97
15k
C-12
C-11
1
C93
0.01µ/25v
R93 360kF
R100
150kF
R99
300k
Q21
DTA123JKA
D20 1SS355
C-8
R98
620k
C-7
144
MA152WA
P05
P04
P03
P02
P01
P00
P17
P16
P15
P14
AIN7
AIN6
AIN5
AIN4
RESET
NC
XCOUT
XCIN
NC
VCC
OSCSEL
XOUT
VSS
NC
XIN
NC
AIN3
AIN2
AIN1
AIN0
COM8
COM9
COM10
COM11
COM12
COM13
R92 1.8kF
F-1
AH SENSOR
(J13) 4.7k
C14 0.01µ/25v
COM0
Q30
DTA143EAK
35
NC
DOOR
SENSING
SWITCH
NC
AIN0
R10 1k
ZD10
UDZ4.3B
C13 0.01µ/25v
R12 15k
CNTRO
IC-2
BA4558
P44
MICRO
SENSOR DEFROST TURNTABLE OFF COOK HELP
AIN4
C-5
C20
0.1µ/50v
C91 0.1µ/50v
BUZZERR
VL2
VL1
3
3
C-6
C90 0.1µ/50v
P45
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
R94
4.7k
R91
3.32kD
R90
330 1w
Q20
DTA143EAK
R102
37.4kF
C-1
8
7
6
5
VA
C18
0.1µ/50v
VL3
D90
1
2
3
4
C-9
R96
3.57kD
VR
C17
0.1µ/50v
C16
0.1µ/50v
LD10 LD11 LD12 LD13
LD15 LD14
C-10
VL4
C15
0.1µ/50v
2
C-3
LED
2
VC
R11 15k
C12
0.1µ/50v
–
C11 0.1µ/50v
+
C10 47µ/16v
C-4
INT
1
1
Q11
DTA143EAK
Q10
2SA1037AK
CN-C
C-2
GND
R69 15k P16
R70 15k P15
R71 15k P14
R72 15k AIN7
G13
R73 15k AIN6
G14
CN-G
6
6
A
B
C
D
E
F
G
H
DMO2420B
DMO2420R
DMO2420S
Figure S-3 LSI Unit Circuit
DMO2420B
DMO2420R
DMO2420S
2
1
4
3
6
5
A
A
B
B
(CN - C)
1
12
1 2
4
E
5
6
ZD1
R1
B
Q3
SP1
1
2
7
8
9
U
C
SH - A
R2
D5
D6
SH - B
B
Q2
C5
D7
VRB
D
2
E Q1 B
R5
R4
3
R3
D8 R6
D
CN - C
1
WH - 1
C4
C
1
9
E
C3
CN - B
D
C2
RY2
C1
10
S
D4
D2
D1
T1
AC
1
VH
VRS1
D3
E
F
P
11
E
2
XA
CN - A
F
F
(J1)
D9
RY1
OMIF
D U
AC
G
(CN - D)
(D10)
G
OL FM
TTM
RY3
H
H
Figure S-4. Printed Wiring Board of Power Unit
1
2
4
3
36
5
6
Technical Service
950 S. Raymond Ave.
Pasadena, CA 91105
800-353-2267
Part # 85927