IP Link® Device Interface
Communication Sheet
barc_1_6373_1.pke
Revision: 2/11/2013
This document provides additional assistance with wiring your Extron IP Link enabled product to your device.
Different components may require a different wiring scheme than those listed below.
For complete operating instructions, refer to the user's manual for the specific Extron IP Link enabled product or
the controlled device manufacturer supplied documentation.
Device Specifications:
Device Type:
Manufacturer:
Firmware Version:
Model(s):
Video Projector
Barco
N/A
RLM W12
Version History:
Driver
Version
1
Date
1/23/2013
IP Link
Compiler
GC
Version
1.5.1
3.3.2
Notes
Initial version.
Driver Notes:
Page 1 of 6
IP Link® Device Interface
Communication Sheet
barc_1_6373_1.pke
Revision: 2/11/2013
Control Commands & States:
Aspect Ratio
5:4
4:3
16:10
16:9
1.88
2.35:1
Letterbox
Native
Unscaled
Auto Image
Execute
Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S-Video
RGBS
HD SDI
Low
DVI
Lamp Mode
Eco
Standard
Lamp Select
Single
Dual
Picture In Picture
On
Off
PIP Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S-Video
RGBS
HD SDI
Top Left
Top Right
Bottom Left
Bottom Right
Split
Power Control
On
Off
Video Mute
On
Off
PIP Position
Page 2 of 6
IP Link® Device Interface
Communication Sheet
barc_1_6373_1.pke
Revision: 2/11/2013
Status Available:
5:4
4:3
16:10
16:9
1.88
2.35:1
Letterbox
Native
Unscaled
Connection Status
Connected
Disconnected
Device Status
Normal
Inlet Temp Over
Temp Sensor Failure
DMD Error
Lamp Overheat
Lamp Ballast Overheated
Ballast communications
error
Lamp Ignition Failure
Lamp does not ignite
Fan Error
System Error
No Signal Present
Interlock
Software I2C Failure
GPIO Failure
EEPROM Failure
EDID Failure
EEP Version Failure
RST Gennum
Status Unavailable
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S-Video
RGBS
HD SDI
Off
Status Unavailable
Off
Status Unavailable
Low
Aspect Ratio
Input
DVI
Lamp 1 Status
On
Lamp 1 Usage
Hours
Lamp 2 Status
On
Lamp 2 Usage
Hours
Lamp Mode
Eco
Standard
Lamp Select
Single
Dual
Operation Hours
Hours
Picture In Picture
On
Off
PIP Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S-Video
RGBS
HD SDI
Top Left
Top Right
Bottom Left
PIP Position
Page 3 of 6
IP Link® Device Interface
Communication Sheet
barc_1_6373_1.pke
Bottom Right
Split
Power Control
On
Off
Power Status
On
Off
Cooling Down
Status Unavailable
On
Off
Video Mute
Page 4 of 6
Revision: 2/11/2013
Warming Up
IP Link® Device Interface
Communication Sheet
barc_1_6373_1.pke
Revision: 2/11/2013
MLC60 Series Supported Commands:
Aspect Ratio
5:4
4:3
16:10
16:9
1.88
2.35:1
Letterbox
Native
Unscaled
Auto Image
Execute
Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S-Video
RGBS
HD SDI
Low
DVI
Lamp Mode
Eco
Standard
Lamp Select
Single
Dual
Picture In Picture
On
Off
PIP Input
HDMI1
HDMI2
RGB
YUV 1
YUV 2
Composite Video
S-Video
RGBS
HD SDI
Top Left
Top Right
Bottom Left
Bottom Right
Split
Power Control
On
Off
Video Mute
On
Off
PIP Position
Page 5 of 6
barc_1_6373_1.pke
IP Link® Device Interface
Communication Sheet
Revision: 2/11/2013
Cable and Adapter Requirements:
M/F RS-232 null modem
Notes for the Device:
Set projector control to RS-232 on OSD as following:
Control  Projector Control  RS-232
Serial communication:
Port Type: RS-232
Baud Rate: 115200
Data Bits: 8
Parity: None
Stop Bits: 1
Flow Control: None
Pin Assignments Diagram:
Note: Captive screw connector may also be used as a serial connection.
General Notes:
Page 6 of 6