advertisement
USER MANUAL
MODEL:
DS Vision® 3000
CAT 5 Range Extender System
P/N: 2900-300282 Rev 2
Contents
Achieving the Best Performance
4 Connecting the DS Vision® 3000
Broadcaster/Transmitter Connections
Receiver/Receiver L Connections
Connecting to the Power Supply
Figures
Figure 1: DS Vision 3000 System Overview
Figure 2: DS Vision 3000 Standard Range
Figure 3: DS Vision 3000 Extended Range with Splitter
Figure 4: Broadcaster Unit - 8 Ports
Figure 6: Receiver DCL Front and Back Connections
DS Vision® 3000
–
Contents
i
1 Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront video, audio, presentation, and broadcasting professionals on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better!
Our 1,000-plus different models now appear in 11 groups that are clearly defined by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;
GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:
Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:
Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:
Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:
Sierra Products.
Congratulations on purchasing your Kramer DS Vision
®
3000, which is ideal for the following typical applications:
Digital signage
Media distribution
DS Vision® 3000 - Introduction 1
2 Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging materials for possible future shipment
Review the contents of this user manual
2.1 Achieving the Best Performance
To achieve the best performance:
Use only good quality connection cables (we recommend Kramer highperformance, high-resolution cables) to avoid interference, deterioration in signal quality due to poor matching, and elevated noise levels (often associated with low quality cables)
Do not secure the cables in tight bundles or roll the slack into tight coils
Avoid interference from neighboring electrical appliances that may adversely influence signal quality
Position your Kramer DS Vision® 3000 away from moisture, excessive sunlight and dust
For best performance the spec of the cable should be:
Gauge: 24AWG (should be written on the cable)
Wire: solid wire (should be written on the cable)
For cable runs over 100m (330ft) the SKEW delay of the cable should be no more than 20ns per 100m (330ft) (should be written in the spec of the cable)
!
This equipment is to be used only inside a building. It may only be connected to other equipment that is installed inside a building.
2 DS Vision® 3000 - Getting Started
2.2 Safety Instructions
!
Caution:
There are no operator serviceable parts inside the unit
Warning:
Use only the Kramer Electronics input power wall adapter that is provided with the unit
Warning:
Disconnect the power and unplug the unit from the wall before installing
2.3 Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled. To comply with the WEEE Directive,
Kramer Electronics has made arrangements with the European Advanced
Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility.
DS Vision® 3000 - Getting Started 3
3 Overview
The DS Vision® 3000 family is a range extender system for computer graphics video signals up to 1080p, stereo audio and bidirectional RS−232. The system can distribute the input signals over CAT 5 cable to hundreds of displays.
Specifically the DS Vision® 3000 features:
A maximum resolution of 1080p
HDTV compatibility
Single CAT 5 cable connections
A system range of 600m (3000ft) @720p
Bidirectional RS-232 control with open protocol for CMS integration
Remote screen query
Palm-held video tuning unit
Group screen on/off command
Out-of-band operation
VESA screen mounts
3 year warranty
3.1 System Overview
Figure 1 gives an overview of the system, showing a broadcaster, line splitter long
and different receiver types.
4 DS Vision® 3000 - Overview
Figure 1: DS Vision 3000 System Overview
Figure 2: DS Vision 3000 Standard Range
Figure 3: DS Vision 3000 Extended Range with Splitter
DS Vision® 3000 - Overview 5
3.2 Transmitter and Broadcaster
This table defines the models:
Kramer
Model
Kramer Part
Number
Full Description
DSV3K-T
(0VS50005) 50-0000509011 Minicom DS Vision 3000 Transmitter 1-port
DSV3K-B8
(0VS50003)
50-0000489011 Minicom DS Vision 3000 Broadcaster 8-ports
DSV3K-B16
(0VS50004) 50-0000499011 Minicom DS Vision 3000 Broadcaster 16-ports
DSV3K-TU
(0VS50008) 50-0000529011 Minicom DS Vision 3000 Video Tuning unit
DSV3K-LS
(0VS50002) 50-0000479011 Minicom DS Vision 3000 Line splitter long 8-ports
DSV3K-RL
(0VS50001) 50-0000469011 Minicom DS Vision 3000 Receiver Long
DSV3K-RS
(0VS50010) 50-0000539011 Minicom DS Vision 3000 Receiver
DSV3K-RDC
(0VS50006) 50-0000519011 Minicom DS Vision 3000 Receiver Dual cascade
Figure 4 illustrates the 8-port broadcaster. The input ports are the same for the
transmitter and 16-port broadcaster, except for the number of system ports. The transmitter has 1 system port and the 16-port broadcaster has 16 system ports.
6
Figure 4: Broadcaster Unit - 8 Ports
DS Vision® 3000 - Overview
3.3 Receivers
The receivers come in the following models:
Receiver - P/N 0VS50010. Reaches up to 110m (330ft) from transmitter/broadcaster
Receiver L (long) - P/N 0VS50001. Reaches up to 300m (1,000ft) from transmitter/broadcaster. With a line splitter L can reach up to 600m (2,000ft) from transmitter/broadcaster.
Note: the maximum cable run from the transmitter/ broadcaster to the line splitter L must not be longer than 300m (1,000ft).
Figure 5 illustrates the receiver and receiver L ports
Note: Both products in Version 3 have the same ports; refer to the part number in order to make sure the product is a receiver or receiver long.
Figure 5: Receiver Ports
3.4 Receiver DCL
The receiver DCL (Dual Cascade Long) P/N 0VS50006 has the following features:
Connects to 2 monitors with each having separate video, audio and serial control
Receiver DCL is cascadable
– it has a pass-through port for connecting more receivers/ receivers L/ receivers DCL/ line splitter L
Can be up to 300m (1,000ft) from a transmitter/broadcaster
With a line splitter L, can be up to 600m (2000ft) from a transmitter/broadcaster
DS Vision® 3000 - Overview 7
Notes:
Dual cascade unit tuning feature influences the VIDEO 1 and VIDEO 2 outputs only, not the SYS OUT port.
Figure 6 illustrates the receiver DCL ports.
Figure 6: Receiver DCL Front and Back Connections
3.5 Line Splitter Long
Add line splitters L(ong) to use for clusters or to increase the number of receivers
in the system. There is an option to cascade line splitters to line splitters. Figure 7
illustrates the line splitter L ports.
Notes: The last cascaded line splitter long must not be more than 300m (1000ft) from the transmitter or broadcaster.
8 DS Vision® 3000 - Overview
Figure 7: Line Splitter Long
3.6 LEDs
This table explains the functions of all the LEDs of the units in the system.
Unit LED Function
Transmitter /
Broadcaster
Receiver /
Receiver L
Receiver DCL
Line Splitter L
Front panel - green
RJ-45 system port - green
/yellow
RJ-45 system port - green
/yellow
Rear panel
– RJ-45 system port - green /yellow
Green - power indicator
Yellow
– link indication
Green - power indicator
Yellow
– link indication, unit is connected to the system this LED flashes from time to time
Yellow flashing constantly
– Bi-directional
RS-232 communication (only possible with one receiver /receiver L at a time)
Green - power indicator
Yellow flashing
– link indication
Green - power indicator
Yellow flashing
– link indication
DS Vision® 3000 - Overview 9
4 Connecting the DS Vision® 3000
Figure 8 illustrates a sample configuration and its connections.
10
Figure 8: Connection Diagram
DS Vision® 3000 - Connecting the DS Vision® 3000
4.1 Broadcaster/Transmitter Connections
1. Connect the broadcaster/transmitter Video In port to the c omputer’s video card with a video cable.
2. Connect the broadcaster/transmitter Serial In port to the computer’s serial port with a serial extender cable.
3. Connect the broadcaster/transmitter Audio In port to the c omputer’s line out port with a stereo audio cable.
4. To use the Video Service Utility, connect the broadcaster/transmitter control port and the c omputer’s serial port with a serial download cable.
5. (Optional) Connect a monitor to the broadcaster/transmitter Video Out port.
4.2 Receiver/Receiver L Connections
1. Connect the screen to the video port.
2. Connect the audio/speakers to the audio port.
Note: if you are connecting the audio out of the receivers to speakers they must have an internal amplifier. The audio out is a line out extension of the player.
3. Where relevant connect the serial connection to the serial port.
4.3 Receiver DCL Connections
1. Connect one screen to video port 1 and another screen to video port 2.
2. Connect the audio/speakers of the first screen to stereo audio port 1 and connect the audio/speakers of the second screen to stereo audio port 2.
Ensure that the video and audio ports are connected to the same numbers, i.e. one screen to video and audio ports 1 and the other screen to video and audio ports 2.
3. Where relevant connect the serial connection to the serial ports 1 and/or 2.
DS Vision® 3000 - Connecting the DS Vision® 3000 11
4.4 Connecting CATx Cables
Connect the CATx cables as follows.
4.4.1 Connecting the Broadcaster/Transmitter
Connect CATx cables to the system ports of the broadcaster/transmitter and the system In ports of receivers/L/DCL or line splitter L.
4.4.2 Connecting/Cascading a Line Splitter Long
Connect CATx cables to the system out ports of the line splitter long and the system in ports of receivers/L/DCL or further line splitters Long.
4.4.3 Cascading a Receiver DCL
Connect a CATx cable to the system out port of the receiver DCL and the system in port of a receiver/L/DCL or line splitter long.
4.5 Connecting to the Power Supply
Connect the transmitter/broadcaster and all receiver and line splitter long units to the power supply using the AC/DC adapters provided with the products.
Once the system is connected the DS Vision® 3000 system broadcasts to all remote monitors/speakers.
4.6 Adjusting the Picture Quality
When the broadcasted picture needs adjusting:
The receiver (version 3)/ receiver L/ receiver DCL/ line splitter long can be tuned either via the service utility, or by using the optional tuning unit
Note: Where there are cascaded receivers/ receiver DCL/line splitters long you must tune them from the unit nearest the broadcaster/transmitter onwards.
4.7 Note on Serial Extension:
The serial connection requires two cables: from player to a transmitter or broadcaster, use a straight serial cable; from receiver to screen, use a cross cable.
12 DS Vision® 3000 - Connecting the DS Vision® 3000
5 Technical Specifications
RESOLUTION:
I/O VIDEO SIGNALS:
SYNC:
HORIZONTAL/VERTICAL SYNC:
SYSTEM CABLE:
MAX. RANGE:
SKEW COMPENSATION:
DDC:
RS-232 CONNECTION:
SERIAL BAUD RATE:
AUDIO:
SERIAL:
OPERATING TEMPERATURE:
STORAGE TEMPERATURE:
WARRANTY:
Up to 1920x1440 @60Hz (depending on cable length)
Analog red, green, blue, 75Ω 0.7Vpp
TTL compatible
Positive/negative
CAT 5/5e/6/7 UTP/FTP cable, 2x4x24AWG solid wire
Receiver short: 110m (360ft),
Receiver long: 300m (1000ft),
Receiver long with line splitter long: 600m (2000ft)
(2 x 300m (1000ft))
Up to 63nsec
Complies with VESA DDC−2 specification
Full serial: RXD, TXD, DTR, DSR, RTS, CTS
Up to 57600
Stereo
Frequency response: 20 Hz to 20 kHz, +/-1 dB.
Signal-to-Noise Ratio (SNR): 80 dBA.
Total Harmonic Distortion and Noise (THD+N):
0.017%.
Stereo crosstalk: -70 dB.
Input impedance: 10kΩ.
Line level output; supports multimedia speakers.
Maximum I/O levels: 3.1Vpp (line level).
Broadcaster / Transmitter
– DCE
Receivers - DTE
5°C to 40°C (41°F to 104°F)
−40°C to 70°C (−104°F to 158°F)
3 years
DS Vision® 3000 - Technical Specifications 13
For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found.
!
SAFETY WARNING
Disconnect the unit from the power supply before opening and servicing
Rev: 2 P/N: 2900- 300282
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project