American DJ Quad Phase Go Instruction manual

Quad Phase Go General Information
Unpacking: Thank you for purchasing the Quad Phase Go by ADJ
Products, LLC. Every Quad Phase Go has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your fixture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without
contacting customer support first.
Introduction: The Quad Phase Go is a rechargeable lithium battery
powered, DMX intelligent, moonflower effect. The fixture can operate
in as a stand alone fixture or in a Master/Slave configuration. The Quad
Phase Go has two operating modes; sound active and DMX Control.
For best results use fog or special effects smoke to enhance the beams
projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@adj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! This may cause eye damage. Avoid looking directly into the
User Instructions
Rev. 3/14
light source. Use sensible precaution.
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 2
Quad Phase Go General Instructions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Quad Phase Go •
•
•
•
•
•
•
•
Features
DMX-512 Protocol Compatible (Four DMX Channels)
RGBW
Bright 10 Watt Quad CREE LED
2 Operating Modes - Sound Active & DMX Control
Internal Microphone
Digital Display for Address and Function Setting
UC3 Controller (Not Included)
Power Cord Daisy Chain
Quad Phase Go
Warranty Registration
The Quad Phase Go carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.
Quad Phase Go Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to this unit.
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 3
Quad Phase Go Safety Precautions
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required voltage for your unit.
•Do not attempt to operate this unit if the power cord has been
frayed or broken.
•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 20 for cleaning details.
•Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 4
Quad Phase Go Battery Precautions
1. Handling of Batteries
1.1 Do Not Short Circuit the Battery
Try to never short circuit the battery. It generates a very high
current which could cause the battery to overheat which may
result in electrolyte gel leakage, harmful fumes, or explosion.
The LIR tabs may easily short-circuit by placing them on conductive surface. A short circuit may lead to heat build up and
damage of the battery. An appropriate circuitry with PCM is
employed to protect accidental short circuit of the battery pack.
1.2 Mechanical shock
Droping the unit, impact hit, bending, etc. may cause failure or
shortend life of the LIR battery.
3. Other
3.1 Battery connection
1). Direct soldering of wire leads or devices to the battery is
strictly prohibited.
2). Lead tabs with pre-soldered wiring shall be spot welded to
the batteries. Direct soldering may cause damage of components, such as separator and insulator, by heat build up.
3.2 Prevention of short circuit within a battery pack
There is enough insulation layers between wiring and the batteries to provide extra safety protection. The battery pack is
constructed in a way that no short circuit will occur which may
cause smoke or fire.
3.3 Do No Disassemble the Batteries
1). Never disassemble the batteries.
Doing this may cause a internal short circuit in the battery,
which may lead to harmful fumes, fire, explosion, or other problems.
Quad Phase Go Battery Precautions
area of contact immediately with fresh water and seek medical
attention immediately.
3.4 Do Not Expose the Battery to Heat or Fire
Never incinerate or dispose of the batteries in fire. This may
cause an explosion, which would be very dangerous.
3.5 Do Not Expose the Battery to water or liquids
Never soak/drop the batteries in liquids such as water, seawater, drinks such as soft drinks, juices, coffee or other.
3.6 Battery Replacement
For battery replacement please contact ADJ Products, LLC
customer support (800) 322-6337.
3.7 Do Not use a damaged Battery
The battery could be damaged during shipping, caused by
shock. Should the battery be found damaged, including damages to the plastic casing of the battery, deformation of the
battery package, smelling of an electrolyte, or leakage of the
electrolyte gel, or other, DO NOT use the battery. A battery with
a odor of electrolyte or a gel leakage should be placed away
from fire to avoid fire or explosion.
4. Battery Storage
When storing the battery, it should be stored at room temperature, with a charge of at least 50%. We recommend that during
long periods of storage that the battery be charged every 6
months. Doing this will prolong the life of the battery and will
also make sure that the battery charge does not fall below the
30% mark.
2). Electrolyte Gel is harmful
Electrolyte Gel should not leak from the LIR battery. Should the
electrolyte gel come into contact with the skin or eyes, flush the
5. Other Chemical Reaction
Because batteries utilize a chemical reaction, battery performance will deteriorate over time even if stored for a long period
of time without being used. In addition, if the various usage
conditions such as charge, discharge, ambient temperature,
etc. are not maintained within the specified ranges, the
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 5
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 6
Quad Phase Go
Set Up
Quad Phase Go
Power Supply: The ADJ Quad Phase Go contains a automatic volt-
DMX+,DMX-,COMMON
cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
SOUND
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
COMMON
DMX512 OUT
3-PIN XLR
1
2
3
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 7
1
2
DMX +
3
DMX -
3
1
DMX512 IN
3-PIN XLR
2
3
1
2
Figure 2
XLR Female Socket
XLR Male Socket
1 Ground
2 Cold
2 Cold
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
1 Ground
XLR Pin Configuration
Pin 1 = Ground
REMOTE
CONTROL
SOUND
3 Hot
INPUT
OUTPUT
INPUT
Pin 2
= Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
POWER
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Quad Phase Go can be controlled via DMX-512
protocol. The Quad Phase Go is a four channel DMX unit. The DMX
address is set electronically using the controls on the back panel
of
COMMON
DMX
+
the unit. Your unit and your DMX controller require
a
approved
DMXDMX512 OUT
3-PIN XLR
DMX 512 110 Ohm Data cable for data input and data
output (Figure 1). We recommend Accu-Cable DMX
cables. If you are making your own cables, be sure
to use standard 110-120 Ohm shielded cable (This
cable may be purchased at almost all professional
sound and lighting stores). Your cables should be
made with a male and female XLR connector on
either end of the cable. Also remember that DMX
Figure 1
cable must be daisy chained and cannot be split.
POWER
Notice: Be sure to follow
figures two and three when making your own
DMX512
age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned
DMX512to address 1
DMX+,DMX-,COMMON
to that unit, no matter where it is located in the DMX chain.
Set Up
POWER
POWER
3
1
2
DMX512 IN
3-PIN XLR
3
1
2
POWER
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 8
Termination
avoids sign
and interfere
to connect a
120 Ohm 1/4
and PIN 3 (
Quad Phase Go
Set Up
Quad Phase Go
System Menu
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
DMX 512 address setting
Master mode
Slave mode 1
Slave mode 2
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Pin 4 - Do Not Use
Not Used
Pin 5 - Do Not Use
Sound mode on
Sound mode off
Sound sense 0-100
MENU
DMX state
LED on
LED off
Normal
Inversion
Battery state
Fixture hours
Software version
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 9
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 10
Quad Phase Go
System Menu
ADDR - DMX Address Setting.
1. Tap the either the MENU, UP, or DOWN buttons until “ADDR”
is displayed, press ENTER.
2. “1” will now be displayed and flashing. Press the UP or
DOWN buttons to find your desired address. Press ENTER to
set your desired DMX address.
SLND - This will let you set unit as a master or slave in a
master/slave configuration.
1. Tap the either the MENU button until “SLND” is displayed,
press ENTER. “MAST”, “SL 1” or “SL 2” will be displayed.
2. Tap the UP or DOWN buttons until your desired setting is
displayed, press ENTER to confim and exit.
SOUN - Sound Active mode. NOTE: When running the
fixture as a single fixture, it must be set to the Master setting. See page above for Master setting.
1. Tap the MENU button until “SOUN” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode,
or “OFF” to deactivate sound active mode.
Quad Phase Go
System Menu
and hold the MENU button for at least 3 seconds to confirm.
DNST - This mode can be used as a precaution mode, that
in case the DMX signal is lost, the operating mode chosen
in the setup is the running mode the fixture will go into when
the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is
applied.
1. Press the MENU button until “DNST” is displayed, press
ENTER.
2. Either “MAST”, “BLND”, or “LAST” will be displayed. Choose
an operating mode you would like the unit to start up in when
power is applied or the DMX signal is lost.
• MAST (Master Slave) - If the DMX signal is lost or power is
applied, the unit will automatically go into Master Slave mode.
• BLND (Blackout) - If the DMX signal is lost or power is applied,
the unit will automatically go into stand by mode.
• LAST (Last State) - If the DMX signal is lost the fixture will stay
in the last DMX set up. If power is applied and this mode is set,
the unit will automatically go into the last DMX set up.
3. Press ENTER to confirm your desired set up.
3. Press ENTER to confirm.
LED - With this function you can switch the LED on or off
SENS - Using this mode, you can set the sound sensitiv-
1. Tap the either the MENU button until “LED” is displayed,
press ENTER.
ity level. 1 for least sensitive, 100 for more sensitive.
1. Tap the MENU button until “SENS” is displayed, press ENTER.
2. Using the UP or DOWN buttons adjust the sensivity level to your
desire.
3. When you found your desired level, press the ENTER, and then press
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 11
via the control board.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to switch on the LED, or “OFF”
to switch off the LED.
3. Press ENTER to confirm and exit.
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 12
Quad Phase Go
System Menu
DISP - This function will reverse the display 180º.
1. Tap the either the MENU button until “DISP” is displayed,
press ENTER.
2. Press the UP button to select “DSIP” to to invert the display,
or “DISP” to revert it.
3. Press ENTER to confirm.
BATT - This function is used for battery charging.
Quad Phase Go
System Menu
to exit.
VER - Use this function to display the Software version of
the unit.
1. Tap the either the MENU button until “VER” is displayed,
press ENTER.
2. The display will show the software version.
1. Press the MENU button until “BATT” is displayed, press
ENTER.
2. Either “CHAR”, “LOAD”, or “STAT” will be displayed. Use the
UP or DOWN buttons to scroll through the functions, and press
ENTER to select your desired function.
• CHAR (Charging) - When this is selected you are able to charge
or stop charging the battery. When a power cable is connected
and “ON” is selected, the battery is now being charged. To stop
charging, select “OFF”.
• LOAD (LED On or OFF) - This will let you blackout the LED while
charging. Select “OFF” to blackout the LED or “ON” to stop the
LED blackout.
• STAT (Charge Status) - This will let you check the battery status.
3. Press ENTER to confirm your setting and exit.
FHRS - With this function you can display the running
time of the unit.
1. Tap the either the MENU button until “FHRS” is displayed,
press ENTER.
2. The display shows the running time of the unit. Press MENU
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 13
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 14
Quad Phase Go
Operation
Quad Phase Go
Operation
Universal DMX Control: This function allows you to use a Elation®
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 7-9 as well as the set-up specifications that are included with your DMX controller.
2. On the Master unit press the MENU button until “SLND” is dis-
played, and press ENTER. Press the UP and DOWN buttons until “MAST” is displayed, and press ENTER. You have now assigned the unit as a Master in the Master-Slave configuration.
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Quad Phase Go is a four channel DMX fixture. See page 17 for detailed description of the DMX values and traits.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 11 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
Sound Active Mode: This mode allows a single unit or several units
linked together, to run to the beat of the music.
1. Tap the MENU button until “SOUN” is displayed, and press ENTER.
2. Press the UP or DOWN button so that “ON” is displayed. The unit will now run to the beat of the music.
3.
The sound sensitivity can be adjusted by pressing the MENU button until “SENS” is displayed, and then press ENTER. Use the UP or DOWN buttons to adjust the sound sensitivity, 1 being the least sensitive, and 100 being the most sensitive.
4. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Master-Slave Operation: This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using standard XLR microphone cables, daisy chain your units ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 15
together via the XLR connector on the rear of the units. Remem-
ber the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a terminator at the last fixture.
3. For the slave units press the MENU button until “SLND” is dis-
played, then press the UP and DOWN buttons until either “SL 1” or “SL 2” is displayed, and press ENTER.
NOTE: In a Master/Slave configuration you can set one fixture
to Master and then set the next fixture to “SL 2”, the fixtures
will now have contrast movement to each other.
4. The slave units will now follow the Master unit.
5. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout.
Quad Phase Go
Power Cord Daisy Chain
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 6 fixtures maximum. After 6 fixtures you will need
to use a new power outlet. They must be the same fixtures. DO
NOT mix fixtures.
Quad Phase Go
UC3 Control
Stand by
Blackout the unit
Function
1. Synchronous Strobe
2. Two light Strobe
3. Sound Control
Mode
Strobe (LED OFF)
Rotation Speed
1-8
Chase (LED ON)
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 16
Quad Phase Go
Channel
1
2
Value
0 - 255
1 - 16
17 - 33
34 - 50
51 - 67
68 - 84
85 - 101
102 - 118
119 - 135
136 - 152
153 - 169
170 - 186
187 - 203
204 - 220
221 - 237
238 - 255
0-9
10 - 120
121 - 134
135 - 245
246 - 249
250 - 255
3
4
0
1 - 255
0 - 15
16 - 255
DMX Traits
Quad Phase Go
Function
Battery Status:
This function is used to check the life status of the battery.
Plug the fixture in and press the MODE button until “BATT” is
displayed. Use the UP or DOWN buttons to scroll to “STAT”
and press ENTER. The number that is displayed is the remaining battery life. Please do not let the battery fully die, this
severly shortens the life of the battery.
COLOR SELECTION
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
COLOR 8
COLOR 9
COLOR 10
COLOR 11
COLOR 12
COLOR 13
COLOR 14
COLOR 15
Example: If “50” is displayed, the battery is at half life. If “25” is
displayed, the battery is at 25% life.
NOTE: When the battery is charging or if the battery life is
below 30% the digital display will flash.
Battery Recharge: To recharge the battery, plug the supplied
AC cord into the AC input on the side of the unit and plug the
other end into a matching power supply.
Press the MODE button until “BATT” is displayed, and press
ENTER.
ROTATION
NO ROTATION
CLOCKWISE FAST - SLOW
NO ROTATION
COUNTER-CLOCKWISE
SLOW - FAST
NO ROTATION
SOUND ACTIVE
STROBING
OFF
STROBING SLOW - FAST
SHUTTER OPEN
OFF
OPEN
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 17
Battery Status & Charging
Use the UP or DOWN buttons to scroll to the menu “CHAR”
then press ENTER.
Use the UP or DOWN buttons to scroll to “ON”, and press
ENTER. The after you select “ON” the battery is now being
charged. To stop charging the battery, select “OFF”.
If the battery is being charged, and the unit is not being used,
press the MODE button until “BATT” is displayed, and press
ENTER. Use the UP or DOWN buttons to scroll to “LOAD” and
press ENTER. Select “ON” to keep the LED on, or “OFF” to
blackout the unit.
It takes about 6 hours to reach full charge.
Note: When unplugging the unit from charging and then
applying power via battery, there will be a minimal charge
drop.
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 18
Quad Phase Go
Battery Replacement
Battery replacement is pretty simple. Unscrew the two thumbscrews
located on the rear of the unit.
Carefully slide the battery out and disconnect the wire as shown
below.
Connect the new battery and slide the battery back in. Screw the two
thumbscrews back in to secure the battery.
Quad Phase Go
Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
Quad Phase Go Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses and mirror should be carried out
periodically to optimize light output. Cleaning frequency depends on
the environment in which the fixture operates (I.e. smoke, fog residue,
dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Always be sure to dry all parts completely before plugging the unit back in.
Quad Phase Go Quad Phase Go
Installation
The unit should be mounted using a mounting clamp (not provided),
affixing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the fixture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 19
Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1.Be sure you have connected your unit into a standard 120v wall outlet.
2. Be sure the external fuse has not blown. The fuse is located on the rear panel of the unit.
3.Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 20
Quad Phase Go Warranty
Quad Phase Go Notes
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs
or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay
return shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon it’s products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published. This warranty was revised after December 1, 2012.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED, Laser Products and lamps)
• Laser Products = 90-Day Limited Warranty
• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 21
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 22
Quad Phase Go Model: Specifications
Quad Phase Go
Voltage:
100V ~ 240V 50 ~ 60Hz
LED:
1 x 10 Watt 4-in-1 CREE LED
Battery Life:
8 Hours Full On (Fully Charged)
Power Draw:
60W
Fuse:6.3A
Power Cord Daisy Chain: 6 Fixtures Max.
Dimensions: 13.25”(L) x 7.75”(W) x 13.25”(H)
335mm x 196mm x 336.5mm
Weight:
14 Lbs. / 6.3 kgs.
Colors:
RGBW
Beam Angle:
65 Degree
Duty Cycle:
None
DMX Channels:
4
Sound Active:Yes
Working Position:
Any Safe, Secure Position
Warranty:
2 Year (730 days)
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
ADJ Products, LLC - www.adj.com - Quad Phase Go Instruction Manual Page 23
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.com
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99