Keystone KSTAW08B Installation instructions


Add to my manuals
36 Pages

advertisement

Keystone KSTAW08B Installation instructions | Manualzz

ROOM AIR CONDITIONER

Model:KSTAW06B

KSTAW08B

KSTAW10B

KSTAW12B

TA B L E O F C O N T E N T S

Important Safety Instructions ......................1-3

Installation Instructions.................................4-7

Normal Sounds..............................................8

Air Conditioner Features............................8-10

Care and Cleaning...................................10-11

Troubleshooting Tip..................................11-12

Warranty Term..............................................13

Before using your air conditioner, please read this manual carefully and keep it for future reference.

Producto

ON CENTER

MEDLEY FL 33178-1037

PRODUCT REGISTRATI

11800 NW 100 ROAD STE 4

MIDEA AMERICA CORPORATION

1 866 646 4332

1 866 646 4332

IMPORTANT SAFETY INSTRUCTIONS

READ THIS MANUAL

Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting

Tips first, you may not need to call for service at all.

To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The seriousness is classified by the following indications.

WARNING This symbol indicates the possibility of death or serious injury.

CAUTION This symbol indicates the possibility of injury or damage to property.

Never do this.

Always do this.

WARNING

Plug in power plug properly.

Otherwise, it may cause electric shock or fire due to excess heat generation.

Always install circuit breaker and a dedicated power circuit.

Incorrect installation may cause fire and electric shock.

Always ensure effective grounding.

Do not operate or stop the unit by inserting or pulling out the power plug.

It may cause electric shock or fire due to heat generation.

Do not damage or use an unspecified power cord.

It may cause electric shock or fire.

If the power cord is damaged, it must be replaced by the manufacturer or an authorised service centre or a similarly qualified per son in order to avoid a hazard.

Do not direct airflow at room occupants only.

Do not operate with wet hands or in damp environment.

It may cause electric shock.

This could damage your health.

Do not allow water to run into electric parts.

Do not modify power cord length or share the outlet with other appliances.

Incorrect grounding may cause electric shock.

Unplug the unit if strange sounds, smell, or smoke comes from it.

It may cause fire and electric shock.

Keep firearms away.

It may cause failure of machine or electric shock.

Do not use the socket if it is loose or damaged.

It may cause electric shock or fire due to heat generation.

Do not open the unit during operation.

It may cause fire and electric shock.

Do not use the power cord close to heating appliances.

It may cause electric shock.

Do not use the power cord near flammable gas or combustibles, such as gasoline, benzene, thinner, etc.

It may cause an explosion or fire.

It may cause fire.

It may cause fire and electric shock.

Ventilate room before operating air conditioner if there is a gas leakage from another appliance.

It may cause explosion, fire and, burns.

Do not disassemble or modify unit.

It may cause failure and electric shock.

1

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

When the air filter is to be removed, do not touch the metal parts of the unit.

It may cause an injury.

Do not put a pet or house plant where it will be exposed to direct air flow.

This could injure the pet or plant.

Ventilate the room well when used together with a stove, etc.

An oxygen shortage may occur.

Do not use strong detergent such as wax or thinner but use a soft cloth.

Appearance may be deteriorated due to change of product color or scratching of its surface.

Do not clean the air conditioner with water.

Water may enter the unit and degrade the insulation. It may cause an electric shock.

Do not use for special purposes.

Stop operation and close the window in storm or hurricane.

Operation with windows opened may cause wetting of indoor and soaking of household furniture.

When the unit is to be cleaned, switch off, and turn off the circuit breaker.

Do not clean unit when power is on as it maycause fire and electricshock, it may cause an injury.

Ensure that the installation bracket of the outdoor appliance is not damaged due to prolonged exposure.

If bracket is damaged, there is concern of damage due to falling of unit.

Always insert the filters securely.

Clean filter once every two weeks.

Hold the plug by the head of the power plug when taking it out.

Turn off the main power switch when not sing the unit for a long time.

Do not place obstacles around air-inlets or inside of air-outlet.

It may cause electric shock and damage.

Do not place heavy object on the power cord and ensure that the cord is not compressed.

Do not drink water drained from air conditioner.

It may cause failure of appliance or accident.

Use caution when unpacking and

There is danger of fire or electric shock.

installing. Sharp edges could cause injury.

If water enters the unit, turn the unit off at the power outlet and switch off the circuit breaker. Isolate supply by taking the power-plug out and contact a qualified service technician.

CAUTION

This appliance is not intended for use by persons

(including children) with reduced physical ,sensory or mental capabilities or lack of experience and knowledge,unless they have been givensupervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

The appliance shall be installed in accordance with national wiring regulations.

Do not operate your air conditioner in a wet room such as a bathroom or laundry room.

The appliance with electric heater shall have at least 1 meter space to the combustible materials.

Contact the authorised service technician for repair or maintenance of this unit.

Contact the authorised installer for installation of this unit.

2

IMPORTANT SAFETY INSTRUCTIONS

NOTE:

The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire.

Please refer to the section Operation of Current Device for details.In the event that the power supply cord is damaged, it cannot be repaired-it must be replaced with a cord from the Product Manufacturer.

WARNING

Avoid fire hazard or electric shock. Do not use an extension cord or an adaptor plug.

Do not remove any prong from the power cord.

Grounding type wall receptacle

WARNING

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WARNING

Prevent Accidents

To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner, follow basic precautions, including the following:

Be sure the electrical service is adequate for the model you have chosen. This information can be found on the serial plate, which is located on the side of the the cabinet and behind the grille.

If the air conditioner is to be installed in a window, you will probably want to clean both sides of the glass first. If the window is a triple-track type with a screen panel included, remove the screen completely before installation.

Be sure the air conditioner has been securely and correctly installed according to the installation instructions in this manual. Save this manual for possible future use in removing or installing this unit.

When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils.

Do not, under any ci rcum sta nces, cut, remov e, or bypass the grounding pro ng.

Powe r su pply cord w ith 3-prong grounding plug and c urrent detection device

WARNING

Electrical Information

The complete electical rating of your new room air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements.

Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards.

Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle. Ensure the receptacle is accessible after the unit installation.

Do not run air conditioner without side protective cover in place.This could result in mechanical damage within the air conditioner.

Do not use an extension cord or an adapter plug.

Op eratio n of Cu r rent D evice

(Applicable to the unit adopts current detection device only )

The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following:

1. Plug in the Air Conditioner.

2. The power supply cord will have TWO buttons on the plug head. Press the TEST button, you will notice a click as the

RESET button pops out.

3. Press the RESET button, again you will notice a click as the button engages.

4. The power supply cord is now supplying electricity to the unit. (On some products this it also indicated by a light on the plug head.)

NOTE:

Do not use this device to turn the unit on or off.

Always make sure the RESET button is pushed in for correct operation.

The power supply must be replaced if it fails reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer.

If power supply cord is damaged, it cannot be repaired. It

MUST be replaced by one obtained from the product manufacturer.

NOTE:This air conditioner is designed to be operated under condition as follows:

Cooling operation

Outdoor temp:

Indoor temp:

O O O O

64-109 F/18-43 C (64-125 F/18-52 C for special tropical models)

O 62-90 F/

O

17-32 C

Heating operation

Outdoor temp:

Indoor temp:

O 23-76 F/ -5-24

O

C

O 32-80 F/

O

0-27 C

Note: P erformance may be reduced outside of these operating temperatures.

3

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT-

Save these instructions for local inspector s use.

IMPORTANT-

Observe all governing codes and ordianaces.

Note to Installer

-

Be sure to leave these instructions with the Consumer.

Note to Consumer

-

Keep these instructions for futrue reference.

Skill level

-

Installatio of this appliance requires basic mechanical skills.

Completion time

-

Approximately 1 hour.

We recommend that two people install this product.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the Warranty.

You MUST use all supplied parts and use proper installation procedures as described in these instructions when installing this air conditioner.

CAUTION

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

Do not change the plug on the power cord of the air conditioner.

Aluminum house wiring may present special problems- consult a qualified electircian.

When handling unit, be careful to avoid cuts from sharp metal edges and aluminum fins on front and rear coils.

TOOLS YOU WILL NEED

Screwdriver

Level

TOOLS YOU MAY USE

WINDOW REQUIREMENTS

Your air conditioner is designed to install in standard double hung windows with opening widths of 23 to 36 inches(584mm to 914mm) .

Screwdriver

Pencil

H

Ruler or tape measure

Scissors or knife

H

Model 6000~8000Btu/h 10000~12000Btu/h

14 (356mm )

Table 1

15-1/2 (394mm)

NOTE:

Save Carton and these Installation Instructions for future reference. The carton is the best way to store unit during winter, or when not in use.

4

INSTALLATION INSTRUCTIONS

PREPARE THE WINDOW

Lower sas h must open sufficiently to allow a clear vertical opening (H) of following size (see Table 1).

Side louvers and the rear of the AC must have c lear air space to allow enough airflow through the condenser,for heat removal. The rear of the unit must be outdoors, not inside a building or garage.

Mounting Hardware

C: Align the hole in the top rail with those in the top of the unit as shown in Fig.B

Fi g.B

3/ 4 (or 1/ 2 ) Lock Frame

Screws (2)

(7)

Sash Lock

(1)

Window sash sea l foam

(1)

D: Secure the top rail to the unit with the 3/8 Screws as s hown in Fig.C.

Fig .C

PREPARE AIR CONDITIONER

A: Remove the air conditioner from the carton and place on a flat surface.

B: Remove top rail from the packaging material as shown in Fig. A.

Top Rail Hardware

3/8 Screws

(4)

Top R ail

(1)

Fig.A

NOTE: For safety reasons, all four(4) s crews MUST be securely fastened.

NOTE: The top rail hardware and the Fig.A,

Fig.B and Fig.C are not applicable t o the units more t han 10000Btu/h.Before installing unit, the top rail must be assembled on the unit (For

<10000Btu/h models only).

INSTALL THE ACCORDION PANELS

NOTE: Top rail and Sliding Panels at each side are offset to provide the proper pitch to the rear of (5/16 ).

This is n ecessary for proper condensed water utilization and drainage. If you are not using the Side

Pan els for any reason, this pitch to the rea r must be maintained.

A.Pla ce unit on floo r, a bench o r a ta ble. Hold the Acco rd ion

Panel in one ha nd and gently p ull back the center to fr ee the o pe n end. See Fig.1

Packaging

Top Rail

Fig.1

5

INSTALLATION INSTRUCTIONS

B. Slide the free end " Ⅰ " section of the panel directly into the cabinet as shown in Fig. 2. Slide the panel down. Be sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet.

" Ⅰ "section

Fig.2

C. Once the panel has been installed on the side of the cabinet, make s ure it sits securely inside the frame channel by making slight adjustments .

Slide the top and bottom ends of the fr ame into the top and bottom rails of the cabinet. Fig.3.

SECURE THE ACCORDION PANE LS

A.Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (Fig.5). Carefully close the window behind the top rail of the unit.

Measure from the cabinet edge

H

H:A bout 3 /4 to 1 ( for 5 to 8K );

3

H:Abo ut 1 to 1 /

8

( for 10 to12K );

INSIDE

Wooden Windows

OUTSIDE

Fig.5

N OT E: Check that air conditioner is tilted back about

O O H (Fig.5)(tilted about 3 to 4 downward to the outside).

After proper installation, condensate should not drain from the overflow drain hole duringnormal use,correct the slope otherwise.

B.Extend the side panels out against the window frame (Fig.6).

Top Rail

Bottom Rail

Fig.3

D. Slide the panel all the way in and repeat on the other side.

Fig.4

Top Rail

Top right

Top left window frame

Fig.6

INSTALL SUPPORT BRACKET

A.Place the frame lock between the frame extensions and the window sill as shown(Fig.7).

/ 2 "(12.7mm) locking screws through the frame lock and into the sill .

NOTE : To prevent window sill from splitting,drill

1 / 8" (3mm) pilot holes before driving screws .

Bottom Rail

NOTE: If storm window blocks AC, see Fig. 11.

Fig.7

6

INSTALLATION INSTRUCTIONS

B.Drive

3/4" (19mm) or 1/2" (12.7mm) locking screws through frame holes into window sash (Fig.8).

Fig.8

C.To secure lower sash in place, attach right angle sash lock with 3/4" (19mm) or 1 /2" (12.7mm) screw as shown(Fig.9).

If AC is Blocked by Stor m W indow

Add wood as shown in Fig.11, or remove storm window before air c onditioner is installed.

If Storm Window Fr ame must remain, be sure the drain holes or slots are not caulked or painted shut.

Accumulated Rain Water or Condensation m ust be allowed to drain out.

Removing AC Fr om W indow

Turn AC off, and disconnect power cord.

Remove sash seal from between windows, and unscrew safety sash lock.

Remove screws installed through frame and framelock.

Close (slide) side panels into frame.

Keeping a firm grip on air conditioner, raise sash and carefully remove.

Be carefully not to spill any remaining water while lifting unit from window. Store parts WITH air conditioner.

Fig.9

D.Cut

Window sash seal foam and insert it in the space between the upper and lower sashes (Fig.10).

FOAM SEAL

SASH

Storm window frame or other obstruction.

1-1/2"min

(38 mm)

Bo ard th ickne ss as requ ired, fo r prop er pi tch to rear, al ong e ntire si ll. Fasten wi th na ils or sc rews .

Fig.11

Fig.10

7

NORMAL SOUNDS

High Pitch ed Cha tter

Hig h efficiency compressors ma y have a high pitched cha tter dur ing the cooling cycle.

Vib ration

U nit may vibra te and make noise b ecause of po or wall or win dow co nstruction o r incorrect in stallation.

Sound of Rushing Air

At the front of the unit, you may hear t he sound of rushing air being moved by th e fan

Pinging or Swit ching

Droplets of w ater hitting c ondenser during norma l operation m ay cause pinging or s witching sou nds.

Gu rgle/H iss

Gurgling or hissing nois e may be heard du e to refrigera nt passing thro ugh evapora tor during norm al operation .

NOTE:

All the illustra tions in this manual are f or exp lanation purp ose only. Your air conditio ner may be slightly different. The actual shape shall prevail.

AIR CONDITIONER FEATURES

ELECTRONIC CONTRO L OPERAT ING INSTR UCTIONS

Before you beg in, thoroughly familiarize yourself with the control panel as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit control alone or with the remote.

A DJUSTS

T EMPER ATURE

O R TIME

ACTIVATES

TIMER

Temp Temp

Timer Timer

On

Off

Che ck

Filt er

Timer

Sleep

ADJUST S

TEMPER ATURE

OR TIME

DISPL AYS

TEMP ERATURE

OR TIM E OR ERROR CODES

SLEEP M ODE

TO TURN UNIT ON OR OFF:

Pre ss ON/OFF button to turn unit on or off.

NOTE:Th e u ni t w i ll i ni ti a t e automatically the Energy

Saver function under Cool, Dry,Auto(only Auto-Cooling and Auto-Fan) modes.

C HECK F ILTER

R ESET B UTTON

SE TS MODE

REMOTE SIGN AL

RECEPTOR

ENERGY

SAVER MODE

Auto

Co ol

Dry

Fan

Mod e Fan

Auto

Low

Med

High

SET FAN SPEED

F OLLOW ME IND ICATOR

TURNS UNIT

ON OR O FF

TO CHANGE TE MPERATURE SET TING:

Pre ss / UP/DOWN button to change temperature setting.

NOTE:Press or hold either UP( ) or DOWN ( ) button until the desired temperature is seen on the display.

This temperature will be automatically maintained

O O O O anywhere between 62 F(17 C) and 86 F(30 C). If you want the display to read the actual room temperature, see To Operate on Fan Only section.

Energy

Saver

Follow

Me

On/Off

UNIT CONTR OL

8

AIR CONDITIONER FEATURES

TO ADJUST FAN S PEE DS:

Press to selec t the Fan Speed in four steps-Auto,

Low, Med or High. Each time the button is pressed, the fan speed mode is shifted. On Dry mode,the fan speed is controlled at Low automatically.

SL EEP FEATURE :

Press Sleep button to initiate the sleep mode. In this mode the selected temperature will increase by

O O 2 F/1(or 2) C 30 minutes after the mode is selected.

O 1(or 2) C after an additional 30 minutes. This new temperature will be m aintained for 6 hour s before it returns to the originally selected temperature. This ends the S leep mode and the unit will continue to operate as originally programmed. The S leep mode program can be cancelled at any time during operation by pressing the Sleep button again.

CHECK FILT ER FEATURE:

Press Check filter button to initiate theis feature.

This feature is a reminder to clean the Air Filter for more efficient operation. The LED( light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the Check Filter button and the light will go off.

ENERGY SAVER FEATURE:

Press En ergy saver button to initiate this function.

This function is a vailable on COOL, DRY, AUTO

(o nly AUTO-COOL ING and AUTO -FAN) modes.Th e fa n wi ll continue to run for 3 min utes after the compre ssor sh uts off.Th e fan then cycl es on for 2 minutes at 10 minute intervals until the roo m te mperature is above the se t tempe rature, at wh ich time the compressor turns b ack on and Cooli ng

Starts.

FOLLOW ME FEAT URE: (on some models)

Light flashing

On/ Off

This feature can be activated from the remote control ONLY. The remote control serves as a remote thermost at allowing for the precise temperature control at its location.

To activa te th e Fo llo w Me feature, poin t the re mote co ntrol towards th e un it and p re ss the Fo llo w Me button. T he re mote d is play is actu al te mperatur e at its lo ca tion. The re mote control will send this signal to th e air co ndition er e ve ry 3 minute s interval until press the Follow Me bu tton again.

If the u nit d oe s no t re ce ive the Follow M e signal durin g any 7 min utes interval, the u nit will be ep to ind icate the Fo llow Me mod e has end ed.

TO SELEC T THE OPE RATING M ODE:

To choose operating mode, press Mode button.Each

time you press the button, a mode is selected in a sequence that goes from Auto, Cool, Dry and Fan. The indicator light beside will be illuminated and remained on once the mode is selected.

The unit will initiate automatically the Energy Saver func tion under Cool, Dry, Auto(only Auto-Cooling and

Auto-Fan) modes.

To operate on Auto feature:

When you set the air conditioner in AUTO mode, it will automatically select cooling, heating(cooling only models without), or fan only operation depending on what temperature you have selected and the room temperature.

The air conditioner will control room temperature automatically round the temperature point set by you.

In this mode, the fan s peed cannot be adjusted, it starts automatically at a speed acc ording to the room temperature.

To operate on Fan Only:

Use this function only when cooling is not desired,such as for room air circulation or to exhaust s tale air(on some models). ( Remember to open the v ent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can c hoose any fan speed you prefer.

Dur ing this func tion, the display will show the actual room temperature, not the set temperature as in the cooling mode.

In Fan only mode ,the temperature is not adjusted.

To operate on Dry mode:

In this mode, the air conditioner will generally operate in the form of a dehumidifier. Since the conditioned space is a closed or sealed area, s ome degree of cooling will continue.

TIM ER: AUTO STA RT/S TOP F EATU RE:

When the unit is on or off, first press Timer button, the

TIMER ON indicator light illuminates. It indicates the Auto

S tart program is initiated.

When the time of TIMER ON is displayed ,press the Timer button again, the TIMER OFF indicator light illuminates.

It indicates the Auto Stop program is initiated.

P ress or hold the UP or DOWN button to change the Auto time by 0.5 hour increments, up to 10 hours,then at 1 hour increments up to 24 hours.The control will count down the time remaining until start.

The selected time will register in 5 seconds, and the system w ill automatically revert back to display the previous temperatur e setting or room temperature when the unit is on.(when the unit is off,there is no display.)

Turning the unit ON or OFF at any time or adjusting the timer setting to 0.0 will cancel the Auto Start/Stop timed program.

9

AIR CONDITIONER FEATURES

D ISPLAYS:

Te mp Te mp

Ti mer T im er

Displays

DISPLAYS:

Shows the set temperature in " O C or " O F and the

Auto-timer settings.While on Fan only mode,it s hows the room temper ature.

Error codes :

AS-Room t emp eratu re sensor error-Unp lu g the un it and plug i t b ack in. If error rep ea ts, ca ll fo r se rvice.

Evaporator tempe ratu re se nsor error-Unp lug the unit and plug it ba ck i n.If erro r repe ats , call for service.

NOTE : " " is di sp layed a s shown in t he le ft p ic ture.

HS Electri c he ati ng sensor error-Unp lug t he unit an d plug it back in .If error repeats, call for servic e.

NOTE:

If the unit breaks off unexpectedly due to the power cut, it will restart with the previous function setting automatically when the power resumes.

Air Directi onal Louve rs

Levers

Fresh Air Vent Control

(on 1000 0~12000Btu/h models ):

Fig. A (VENT CLOSED) Fig. B (VENT OPEN)

The Fresh Air Vent allows the air conditioner to:

1. Rec irculate inside air - Vent Closed

(See Fig.A)

2. Draw fresh air into the room- Vent Open

(see Fig.B )

Fig. C (VENT & EXHAUST

OPEN)

3. Exchange air from the room and draws fresh air into the room - Vent and Exhaust Open

(see Fig.C)

CARE AND CLEANING

Air Direction

The louvers will allow you to direct the air flow Up or

Down(on some models ) and Left or Right throughout the room as needed. Pivot horizontal louvers until the desired Up/Down direction is obtained.

Move the Levers from side to side until the desired

Left/Right direction is obtained.

ADDITIONAL TH INGS YOU SHOULD KNOW

Now that you have mastered the operating procedure, her e are more features in your control that you s hould bec ome familiar with.

The Cool circuit has an automatic 3 minute tim e delayed start if the unit is turned off and on quickly.

This prevents overheating of the compressor and possible circuit breaker tripping.The fan will continue to run during this time.

The control is capable of display ing temperature in degrees Fahr enheit or degrees Celsius. To convert from one to the other, press and hold the Left and

Right Temp/Timer buttons at the same time, for 3 seconds.

10

CAUTION

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent chock or fire hazards.

Air Filter Cleaning

The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils.

CARE AND CLEANING

Air Filter Cleaning

Push the vent handle to the Vent Closed position

(where applicable). Open the front panel.

Take the filter by the center and pull up and out.

Wash the filter using liquid dishwashing detergent and warm water. Rinse filter thoroughly. Gently shake excess water from the filter. Be sure the filter is thoroughly dry before replacing. Or, instead of washing you may vacuum the filter clean.

Note:

。 。

Never use hot water over 40 C(104 F) to clean the air filter. Never attempt to operate the unit without the air filter.

Cabinet Cleaning

Be sure to unplug the air conditioner to prevent shock or fire hazard. The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Rinse thoroughly and wipe dry.

Never use harsh cleaners, wax or polish on the cabinet front.

Be sure to wring excess water from the cloth before wiping around the controls. Excess water in or around the controls may cause damage to the air conditioner.

Plug in air conditioner.

Winter Storage

If you plan to store the air conditioner during the winter, remove it carefully from the window according to the installation instructions. Cover it with plastic or return it to the original carton.

TROUBLESHOOTING TIPS

Before calling for service, review this list. It may save your time and expense. This list includes common occurrences that are not the result of defective workman-ship or materials in this appliance.

Problem

Air conditioner does not start

Solution

Wall plug disconnected. Push plug firmly into wall outlet.

House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

Plug Current Device Tripped. Press the RESET button.

Power is OFF. Turn power ON.

Air from unit does not feel cold enough rises above

O O

62 F(17 C).

Temperature sensing behind air filter element touching cold coil. Keep it from the cold coil.

Set to a Lower temperature.

Compressor stopped when changing modes. Wait for 3 minutes after set to the COOL mode.

Air conditioner cooling, but room is too warm- ice forming on cooling coil behind decorative front.

Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY mode.

Thermostat set too cold for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then, set temperature to a Higher setting.

11

TROUBLESHOOTING TIPS

Problem

Air conditioner cooling, but room is too warm- NO ice forming on cooling coil behind decorative front.

Air conditioner turns on and off rapidly

Noise when unit is cooling

Solution

Dirty air filter- air restricted. Clean air filter. Refer to Care and Cleaning section.

Temperature is set too High, set temperature to a Lower setting.

Air directional louvers positioned improperly. Position louvers for better air distribution.

Front of units is blocked by drapes, blinds, furniture, etc. - restricts air distribution.

Clear blockage in front of unit.

Doors, windows, registers, etc. Open- cold air escapes. Close doors, windows, registers.

Unit recently turned on in hot room. Allow additional time to remove Stored heat from walls, ceiling, floor and furniture.

Dirty air filter- air restricted. Clean air filter.

Outside temperature extremely hot. Set FAN speed to a Higher setting to bring air past cooling coils more frequently.

Air movement sound. This is normal . If too loud, set to a slower FAN setting.

Window vibration - poor installation. Refer to installation instructions or check with installer.

Improper installation. Tilt air conditioner slightly to the outside to allow water drainage.

Refer to installation instructions - check with installer.

Water dripping

INSIDE when unit is cooling.

Water dripping

OUTSIDE when unit is cooling.

Unit removing large quantity of moisture from humid room. This is normal during excessively humid days.

Remote Sensing

Deactivating

Prematurely

(some models)

Remote control not located within range. Place remote control within 20 feet & 180 , radius of the front of the unit.

Remote control signal obstructed. Remove obstruction.

Room too cold

Set temperature too low. Increase set temperature.

12

AIR CONDITIONER WARRANTY

ONE-YEAR

One

1-866-646-4332

13

The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.

Manual del Usuario

Unidad de aire acondicionado de ventana

Modelo:KSTAW06B

KSTAW08B

KSTAW10B

KSTAW12B

La lista de los contenidos

Instrucciones importantes de la seguridad .....1-3

Instrucción de instalación ..............................4-7

Sonidos normales ...........................................8

Características del aire acondicionado .........8-10

Mantenimento y limpieza ............................10-11

Soluciones de Problemas ...........................11-12

Plazo De Garantía .......................................... 13

Antes de usar su aire acondicionado, lea con cuidado este manual y guárdelo para su consulta posterior.

INSTRUCCIONES IMPORTANTES DE LA SEGURIDAD

Lea este manual

Dentro de este manual podría encontrar muchos consejos ayudables diciendo cómo usa y mantener su aire acondicionado correctamente.le cuesta un poco cuidado antes, le ahorrará mucho tiempo y dinero en su aire acondicionado.Puede encontrar muchas respuestas a los problemas communes en el cuadro de las soluciones de problemas. Si lea nuestro cuadro de las soluciones de problemas primero, quizá no será necesario llamar por servicio.

Para evitar los daños a los usuarios u otra persona, deben seguir las instrucciones siguientes. Las operaciones incorrectas por la ignora de las instrucciones puede causar lesiones o daños. El grado de seriedad está clasificado por lo que indica siguiente.

WARNING Este símbolo indica la posibilidad de muerto o lesiones graves.

CAUTION Este símbolo indica la posibilidad de lesiones o daños a la propiedad.

Nunca lo hace. Siempre hacerlo.

WARNING

Encúfalo en el enchufe adecuadamente

Si no, podría causar una descarga eléctrica o incendio por la generación del calor.

Podría causar una descarga eléctrica por la generación del calor

Siempre instala el interruptor y un circuito de potencia dedicado.

No lo maneje con las manos mojados o en un ambiente húmedo.

Podría causar una descarga eléctrica.

No permite entrar el agua en las piezas eléctricas.

Siempre asegúrese que está puesto a una tierra eficaz.

La tierra incorrecto podría causar una descarga eléctrica.

Si emite sonido, olor o humo extraño , desenchuúfelo.

Podría causar incendio u descarga eléctrica.

Mantener las armas de fuego lejos.

No lo usa el enchufe si está suelto o dañado.

Podría causar incendio u descarga eléctrica.

Podría causar incendio.

que está cerca de los apraratos de calefacciones.

Podría causar incendio y una descarga eléctrica.

Ventile la habitación antes de operar el aire acondicionado si hay una fuga de gas desde otros aparatos.

Podría causar una explosion, incendio y quemaduras.

No lo hace daño o usar un cable eléctrico sospechoso.

Podría causar descarga eléctrica o incendio.

Si el cable eléctrico está dañado, para evitar el peligro, debe reemplazarlo por un fabricante o un servicio autorizado o unidad con cualificación similar.

No dirije el flujo del aire solamente a un ocupante de la habitación.

Podría hacer daños a su salud.

No modifique la longitude del cable eléctrica ni compartiri el enchufe con otros aparatos.

Podría causar una descarga eléctrica o incendio por la generación del calor.

No la abre la unidad durante su operación.

Podría causar descarga eléctrica.

No lo usa el cable electrico cerca de gas inflammable o combustibles, como gasolina, benceno, disolvente, etc.

Podría causar una explosión o incendio.

No desmonte ni modifique la unidad.

Podría causar fallo y descarga eléctrica.

INSTRUCCIONES IMPORTANTES DE LA SEGURIDAD

CAUTION

Cuando el filtro del aire está eliminado, no la toca las partes metálicas de la unidad.

Podría causar una lesion.

No lo guarda una mascot o planta donde sera expuesto al flujo del aire directo.

Podría hacer daño a su mascot o planta.

Ventile bien la habitación cuando se utilize junto con una estufa, etc.

Podría ocurrir la escasez de oxígeno.

No utilice detergente fuerte como cera o algo más delgado, sino usa un paño suave.

La apariencia podría deteriorarse por el cambio del color del producto u arañazos en su superficie.

Detenga el funcionameinto y cierre la ventana en la tormenta o huracán.

humedecimiento y remojo de muebles dentro de la casa.

Siempres inserte el filtro correctamente.Limpie el filtro una vez cada dos semanas.

La operación sin filtro podría causar fallo.

No lo limpie el aire acondicionado con agua.

El agua podría entrar en la unidad y disminuir la aislación.

Podría causar una descarga eléctrica.

Cuando la unidad se va a limpiar, apague y desconecte el disyuntor.

No la limpie la unidad cuando está encendido porque podría causar incendio y una descarga eléctrica, lo cual produciría lesiones.

Sujete la clavija por la cabeza de la clavija de alimentación cuando la saque.

Podría causar descarga eléctrica y daños.

No lo usa para fines especiales.

No lo use este aire acondicionado a conservar dispositivos de precision, alimentos, mascotas, causar deterioro de su calidad, etc.

Si el soporte está dañado, podría producir daños por el fallo de la unidad.

Apaque el interruptor principal de la alimentación cuando la unidad ni hace ruido un largo tiempo.

Podría causar fallo del product o incendio.

No coloque obstáculos en alrededor de la entrada de aire o dentro de la salida del aire.

Podría causar fallos de aplicación o accidente.

Tenga cuidado al desembalar e instalarlo. Su bordes afilados podrían provocar lesiones.

No coloque objetos pesados sobre el cable electrico y aseguúrese que el cable no está comprimido.

Hay peligro de incendio o descarga eléctrica.

No beba el agua drenada del aire acondicionado.

Contiene producer contaminación y podría hacerle enfermo.

Si entra agua en la unidad, apágue la energía fuera y apague el disyuntor.Aisla el suministro mediante la tira de su calbe energetic y contactelo a un servicio técnico cualificado.

CAUTION

Este aparato no está diseñado para ser utilizado por las personas(incluso los niños)con capacidad reducida o falta de experiencia o los conocimientos físicos, sensoriales o mentales ,a menos que sean enseñado o instruidos el uso del aparato por la gente responsible se su seguridad.

Los niños deben ser supervisados para asegurar que no lo jueguen con el aparato.

Si el cable electrico está dañado, debe ser reemplazado por un fabricante , agente de servicio o personas cualificados para evitar peligro.

El aparato debe ser instalado de acuerdo con reglas escritas nacionales.

No lo utilice el aire acondicionado en una habitación mojada somo el baño o lavandería.

Eeste aparato con su calentador electrico deben tener al menos 1 metro lejos a los materials combustibles.

Póngase en contacto con el servicio técnico autorizado para la reparación o mantenimiento de esta unidad.

Póngase en contacto con el instalador autorizado para la instalación de esta unidad.

INSTRUCCIONES IMPORTANTES DE LA SEGURIDAD

NOTA:

El cable de energía con el aire acondicionado contienen un dispositivo de detección de corriente, lo cual está diseñado para reducir el riesgo de incendio.Por favor consulte la sección de Operación del dispositivo de

Corriente los detalles.En el caso que el cable de energía está dañado, no puede ser reparado, debe reemplazarlo por un cable del Fabricante del Producto.

WARNING

Evita el incendio o descarga eléctrica.

No utilice cable de extención ni enchufe adoptado.No remueve ninguna clavaja del cable de energía.

Varada Tipo Pared

Receptáculo

WARNING

Para su seguridad

No guarda o usar gasolina u otros vapors y líquidos inflammables en la proximidad de este o cualquier otro electrodoméstico.

WARNING

Evitar accidentes

Para reducer el riesgo de incendio, descarga eléctrica o lesiones a la gente cuando usted usa el aire acondicionado, siga las precauciones básicas, incluyendo las siguientes:

Asegúrese de que sel servicio electrico sea adecuado para el modelo elegido.

Esta información podría ser encontrado en este serie de places, los cuales están situado en un lado del armario y detrás de la rejilla.

ambos lados de los vidrios primero.Si la ventana es un tipo de triple pista con un panel de pantalla incluído, remueva la pantalla completamente antes de la instalación.

Asegúrese de que el aire acondicionado está instalado a una manera segura manual para quitar lo intalarlo en el future.

Al manipular el aire acondicionado, tenga cuidado para evitar cortes de las aletas metálicas afiladas en los serpentines frontales y traseros.

Nunca, en ningún caso, corte, remueve ni pasar por la conexión a la tierra.

El cable de energía con conexión a tierra de 3 patas y un dispositivo de detección de corriente

WARNING

Información Eléctrica

Las especificaciones eléctricas completas de su nuevo aire acondicionado de la habitación está indicada en el serie de placa.Consulte a las especificaciones cuando comproba los requisites eléctricos.

Asegúrese de que al aire acondiconado está puesto bien.Para minimizar los riesgos de choque electrico e incendio, es muy important ponerlo bien.El cable de energía está equipado conun enchufe de 3 clavijas conectado a la tierra para protección contra posibles descargas eléctricas.

Su aire acondicionado debe ser utilizado en una manera correcta puesta en la teirra.Si el tomacorriente que pretende usar no está adecuadamente conectado a tierra o protegido por un fusible de retard o un interruptor de cirtuito, pida a un electricista calificado que instale el tomacorriente adecuado.Asegúrese de que el recipient sea accessible despúes de la instalación de la unidad.

No funciona el aire acondicionado sin cubierta protectora lateral.Este podría resultar daño

No utilice un cable de extension ni un adaptador.

Operación de Dispositivos de Corriente

(Sólo applicable a la unidad que adopta dispositivo de detección de corriente)

El cable de energía contiene un despositivo que detecta daños en el cable electrico.Para comprobar su cable electrico sigue los siguientes:

1. Enchufe el aire acondicionado.

2. El cable de suministro de corriente tundra dos botones

en el enchufe.Pluse el botón de TEST, le darás cuanta

de un clic cuando el botón TEST salta.

3. Pulse el botón RESET, vuelve a ver un clic cuando tl

botón activa.

4. El cable de suministro de corriente ahora suministra la

electricidad a la unidad.(En algunos productos este

también está indicado por una luz en la cabeza del

enchufe.)

NOTA:

No ultilice este dispositivo a encender o apagar la unidad.

Siempre asegúrese de que el botón RESET está presionado bajo una operación correcta.

La fuente de corriente debe ser reemplazado si falle a restablecerlo ni con el botón TEST o RESET.Se puede obtener un nuevo del fabricante del producto. Si el cable de energia está dañado, no puede ser reparado.

DEBE ser reemplazado por uno obtenido del fabricante del producto.

Funcionamiento de enfriamiento

Funcionamiento de calefacción

Temperatura fuera

Temperatura interior:

Temperatura fuera

Temperatura interior:

64-109°F/18-43°C (64-125°F/18-52°C

Para los modelos tropicales especiales)

62-90°F/17-32°C

23-76°F/°C -5-2

32-80°F/ 0-27°C

Nota: Su rendimiento podría reducir fuera de estas temperaturas operativas.

INSTRUCCIONES DE INSTALACIÓN

Antes de Empezar

Lea esta instrucción completamente y con mucho cuidado.

IMPORTANTE-

Guarda esta instrucción en un lugar del insperctor o el usuario.

IMPORTANTE-

Consulte todos los códigos y ordenanzas vigentes.

Nota para instalar-

Asegúrese de dejar las instrucciones al cliente.

Nota para el cliente-

Guarda la

Nivel de habilidad-

Para instalarla require una habilidad básica mecánica.

Plazo de ejecución-

Approximadamente 1 horas.

Le recomendamos que dos personas lo instalen.

Una instalación correcta es la responsabilidad del instalador.

El fallo del product por una instalación incorrect no está incluído en la garantía.

DEBE usar todas las partes suministradas y los productos de instalación correctamente según la descripción en la instruccióncuando instala esta aire acondicionado.

REQUISITOS DE LA VENTANA

Su aire acondicionado es diseñado para instalar en ventanas estandar de doble panel con un ancho de aperture de 23 a 36 pulgadas(584mm a 914mm).

Acodo

CAUTION

Nunca, en ningún caso corta o remueve la tercera(teirra) clavija del cable de energía.

No lo cambie el enchufe en el cable de energía del aire acondicionado.

Cableado domestic de aluminio podría causar problemas especiales—consulte a un electricista calificado.

Al manipular la unidad, tenga cuidado de evitar cortes de los bordes metálicos afilados y aletas de aluminio en las bobinas frontales y posteriors.

HEERAMIENTOS QUE NECESITE

Destornillador

RANGO

HERRAMIENTOS QUIZÄ NECESITE

Destornillador

Lápiz

Regla o cinta métrica

Tijera o cuchillo

NOTA:

VENTANA DE MADERA

H

Modelo 6000~8000Btu/h

14” (356mm)

Tabla 1

10000~12000Btu/h

15-1/2” (394mm)

INSTALLATION INSTRUCTIONS

PREPARE LA VENTANA

El marco inerior debe poder abrirse un espacio suficiente para la limpieza con una aperture(H) de los siguientes tamaños(consulte la Tabla 1).

Rejillas laterals y la parte trasera de la AC debe tener un espacio libre de aire que permite suficiente flujo de aire através del condensador, para la eliminación del calor.

La parte trasera de la unidad debe estar fuera , no dentro de un edificio ni garaje.

Accesorios de montaje

C: Alinee el agujero en la barra superior con los de la

parte superior de la unidad, como se muestra en la

Fig.B.

D: Instala el riel superior a la unidad con un tronillo de

3/8” como se muestra en la Fig.C.

3/4” (or 1/2” )

Tornillos

(7)

Bloqueo de marco

(2)

Bloqueo de la ventana

(1)

Guillotina de ventanaSello de espuma

(1)

PREPARA EL AIRE ACONDICIONADO

A: Remueva el aire acondicionado desde la caja y coloquelo sobre una superficie plana.

B: Retire el carril superior de la parte posterior del material de envase como se muestra en Fig. A.

Hardware del carril superior

3/8” Tornillos Carril superior

(4) (1)

NOTA: Para su seguridad, todos los cuatro(4) tornillos

DEBEN estar bien sujetos

NOTA: El hardware del carril superior y la Fig.A, Fig.B y Fig.C no son aplicables para la unidad más que

10000Btu/h.Antes de instalarla, el carril superior debe ser montado en la unidad(Sólo para el modelo de<10000Btu/h).

INSTALAR LOS PANELES DEL AIRE

ACONDICIONADO

NOTA: El carril superior y los panesl deslizantes en cada lado se sirve para ofrecer un paso adecuado a la parte trasera(5/16”).Es necesario para la utilización del agua condensada y el drenaje adecuado.Si no use los paneles laterals por ningún razón, debe mantener este paso hacia la parte trasera.

A.Ponga launidad en el suelo, un banco o una mesa.Sujete el panel de acordeón en una mano y suavemente tire hacia atrás el centro para sacarla fuera.

Consulte Fig.1.

Embalaje Carril superior

INSTRUCCIONES DE INSTALACIÓN

B. Deslice la sección"I"del labo libre del panel directamente entre el gabinete como se muestra en Fig.2. Deslice el panel abajo.Asegúrese de dejar suficiente espacio para deslizar el parte superior y inferior del marco entre el carril del gabinete.

"I"sección

C. Una vez el panel está instalado en un lado del gabinete, asegúrese de que esté correctamente dentro del canal del marco con ajustes suaves.Deslice los extremos superior y inferior del marco en el carril del gabinete.Fig.3.

INSTALA LOS PANELES DE ACORDEÓN

A. Agarre firma al aire acondicionado, ponga la unidad en la apertura de la ventana con mucho cuidado para que el fondo del marco del aire acondicionado está contra el umbral de la ventana(Fig. 5). Acerque la ventana detrás el carril superior de la unidad con mucho cuidado.

Mida desde el borde del gabinete

H:Aproxima 3/4” a 1 (para 5 to 8K);

H:Arpoxima 1 a 13/8” (para 10 a 12k);

DENTRO

VENTANA DE MADERA

FUERA

NOTA: Comprueba que el aire acondicionado está inclinada hacia atrás casi H(Fig.5)(inclinado unos 3° a 4° desde el fondo hacia la fuera) despúes de la instalación, correcta, el condensado no debe bajar desde el orificio de drenaje de desbordamiento durante su uso normal, corrige la pendiente de otro modo.

B. Extienda los paneles laterals en contra del marco de la ventana. (Fig.6)

Carril superioro

Marco de ventana

Carril inferior

D. Deslice el panel hasta el fondo y repítalo al otro lado.

Carril superior Derecha superior

Izquierda superior

INSTALAR EL SOPORTE

A.Ponga el bloqueo del marco entre la extension de los marcos y el umbral de la ventana como se muestra(Fig.7).

Llave 3/4 "(19 mm) o 1/2" (12.7 mm) tornillos de bloqueo a través de la cerradura de marco y en el alféizar.

NOTA: Para evitar la division del umbral de la ventana, taladre un agujero piloto de¨1/8¨(3mm) antes de conducer los tornillos.

Carril inferior

NOTA: Si la ventana de la tormenta bloquea AC, consulte

Fig.11.

INSTRUCCIONES DE INSTALACIÓN

B. Conduzca tornillos de bloqueo de 3/4" (19mm) or 1/2"

(12.7mm) entre los agujeros del marco en la hoja de la ventana. (Fig.8).

C. Para instalar la baja hoja inferior en un lugar correcto, coloque bien el bloqueo de la hoja ángulo con tornillos de

3/4" (19mm) o 1 /2" (12.7mm ) como se muestra(Fig.9).

Si AC esté bloqueado por la Ventana de Tormenta

Añada maderas como se muestra en Fig.11, o elimine la ventana de tormenta antes del aire acondicionado.Si el marco de la Ventana de Tormenta debe permanecer, asegúrese de que los agujeros de drenaje o ranuras no se calafatea o se pinta cerrada.El agua de lluvia acumulada o condensada debe puede drenar.

Eliminar AC de la Ventana

Apaga el AC y separalo con el suministro de energía.

Retire el sello de lahoja de vantana y desenrosque el bloqueo seguro de la hoja.

Retire los tornillos instalados a través el marco y bloqueo del marco.

Cierre(deslice) los paneles laterals entre los marcos.

Garre firma al aire acondicionado, levanta la hoja y eliminala con cuidado.

Tenga cuidado no derramar el agua restante mientras levante la unidad desde la ventana.Guarda las partes

CON el aire acondicionado.

Hoja

D. Corte el sello de espuma de la hoja de la ventana y pongala en el lugar entre las hojas superiores y inferiors.

(Fig.10).

Sello de espuma

Ventana de

Tormenta Marco u otra obstrucción

Aborda el grueso según necesidad para un paso adecuado a alzar y un largo umbral entero.Sujetalo con clavos o tornillos.

SONIDOS NORMALES

Sonido Agudo

Un compressor con alta eficiencia podrá tener un sonido agudo durante su ciclo de enfrigeración.

Vibración

La unidad podrá vibarar y hacer ruido por una débil pared o.

construcción de ventana o una instalación incorrect.

Sonido del Corriente del Aire

En la frontera de la unidad, podría oir un sonido del corriente del aire debido al movimiento del ventilador.

El Sonido de Ping o el Conmutadkor

Las gotas del agua cayendo sobre el consensador podría causar el sonido de ping o el conmutador.

Gurgle/Silbido

El sonido de Gurgle/silbido podría ser la consecuencia de que el refrigerante pasa por el evaporador durante su operación normal.

NOTA:

Todas las ilustraciones en esta manual son para explicar sólo.Su aire acondicionado podría ser un poco diferente.Prevalezca a la forma real.

CARACTERÍSTICAS DEL AIRE ACONDICIONADO

INSTRUCCIONES DE LA OPERACIÓN DEL CNOTROL ELECTRÓNICO

Antes de empezar, debe familiarizarse completamente con el panel de control y todas sus funciones como se muestra abajo, despúes sigue los símbolos para las funciones que desea.

La unidad podría ser controlado por el control sólo o con el remoto.

Ajuste la temperatura o reloj

Activar el reloj

Compruebe el filtro botón

RESET

Ajuste la temperatura o reloj

Muestra la temperatura o t iempo o códigos de error

Modo durmiento

Para encender o apagar la unidad

Presiona ON/OFF botón a encender o apagar

NOTA:la unidad iniciará automáticamente la funición de

Ahorro de Energía bajo los modos de Frío, Seco, Auto

(Sólo Auto-Frio y Auto-Ventilador).

Establece el modo

Receptor del signo del remoto

ENERGY

SAVER MODE

Establece la velocidad del ventilador ndicator de Seguirme

Enciende o apagar la unidad

A cambiar las opciones de la temperatura:

Presiona UP/DOWN botón a cambiar las opciones de la temperatura

NOTA:Pulse o mantenga presionando el botón UP( ) or

DOWN( ) hasta se muestra la temperatura que quiere.

La mantiene automáticamente esta temperatura en cualquier lugar entre 62°F(17°C) y 86°F(30°C). Si quiere saber la temperatura actual de la habitación, elige la

Operación de sección Fan Only.

CONTROL DE LA UNIDAD

CARACTERÍSTICAS DEL AIRE ACONDICIONADO

PARA MODIFICAR LA VELOCIDAD DEL VENTILADOR

Presiona a elegir la velocidad del ventiladoren cuatro grados- Auto, Bajo, Med o Alto.Cada vez presiona el botón, se modifica el modo de la velocidad del ventilador.

Bajo el Modo Seco, la velocidad está controlado en Bajo automáticamente.

FUNCIÓN DURMIENTA:

Presiona el botón durmiento a iniciar el modo durmiento. Bajo este modo la temperatura selecciona incrementará a 2°F/1(o 2)°C 30 minutos despúes de elegir el modo.La temperatura va a incrementar un otro

2°F/ 1(o 2)°C despúes de 30 minutos adicional. Esta temperatura va a mantener 6 horas antes de volver a su temperatura elegida originalmente. Esto termina el modo durmiento y la unidad continuará a funcionar según lo programado originalmente.El modo durmiento puede ser cancelado en cualquier momento durante su función con presionando el botón durmiento otra vez.

FUNCIÓN DE INSPECCIÓN:

Presiona comprueba el botón de filtro para iniciar esta función.Esta función es un recordatorio para limpiar el filtro de aire para su funcionamiento eficaz El LED(luz) will illuminaré espúes de 250 horas de función. Para encenderla despúes de la limpieza, presiona el botón

Check Filtery la luz va a apagar.

FUNCIÓN DE AHORRAR LA ENERGÍA:

Presiona botón de ahorrar la energía para iniciar esta función. Esta función es diponible bajo los modos Frío,

Seco, Auto(Sólo Auto-Frío y Auto-VEntilador).El ventilador continua funcionar 3 minutos despúes de que el compresor apaga.Entonces el vantilador gira 2 minutos cada 10 minutos intervalo hasta que la temperatura interior llega a la puesta, cuando el compresor vuelver a funcionar y empieza a enfriar.

FUNCIÓN DE SEGUIRME:(en algunos modos)

Luz parpadeando

FoMlleow

On/Off

Esta función SÓLO puede ser activado por el control remoto.El control remoto sirve como un termostato remoto permitiendo el control preciso de la temperatura en su ubicación.

Para activar la función de Seguirme, apunte el control remoto hacia la unidad y presiona el botón Follow Me.

El remoto muestra la temperatura actual de su ubicación.

El remoto envia signos al aire acondicionado cada 3 minutos intervalos hasta la presiona del botón Follow Me otra vez.Si la unidad no recibe signos desde el Follow Me

7 minutos intervalo, la unidad emitirá un sonido indicando que el modo Follow Me ha terminado.

A elegir el modo operativo:

A elegir el modo operativo, presiona el botón Modo.Cada vez presiona el botón, selecciona un modo siguiendo orden comoAuto, Frío, Seco y Ventilador.La luz del indicador ilumina y mantiene una vez que selecciona el modo.La unidad empieza la función de ahorrar la energía bajo los modos de Frío, Seco, Auto(Sólo Auto-Frío y Auto-Ventilador).

Para operar bajo la función auto:

Cuando elige el modo AUTO del aire acondicionado, elegirá automáticamente operación como enfriamiento, calefacción

(fuera el modo de sólo-frío), o modo de ventilador sólo según la temperatura elegida y la actual de la habitación.

El aire acondicionado controlará la temperatura de la habitación automáticamente alrededor de la temperatura elegida por usted.

En este modo, la velocidad del ventilador no puede ser modificado, empieza automáticamente con una velocidad según la temperatura de la habitación.

Para operar bajo el modo ventilador sólo:

Utilice esta función solamente cuando no quiere friar, sirve como una circulación de aire de la habitación o para extraer el aire viciado(bajo algunos modos).(Recuerde abrir el respiradero durante esta función, pero mantengalo cerrado durante la función de friar para una eficiencia máxima de enfiramiento.)Puede elegir cualquier velocidad del ventilador que prefiere.

Durante esta función, la pantalla mostrará la temperatura actual de la habitación, no la temperatura elegida, como el modo frío.

Bajo el modo de ventilador sólo ,la temperatura no será ajustado.

Para operar bajo el modo Seco:

Bajo este modo,el aire acondicionado poco a poco funciona en una manera de deshumidificador.Como el espacio condicionado es cerrado o sellado, un cierto grado de enfriamiento continuará.

RELOJ: FUNCIÓN DE AUTO EMPEZAR O TERMINAR:

Cuando enciende la unidad, primero presiona el botón reloj, el indicador TIMER ON luz ilumina.Este indica que el programa de Auto Empezar está iniciado.

Cuando el tiempo del TIMER ON muestra, Presiona el botón otra vez, el indicador TIMER OFF luz ilumina, indicando que el programa de Auto Terminar está iniciado.

Pulse o mantenga pulsando el botón UP o Down para cambiar el tiempo de Auto por incrementos de 0.5 horas hasta 10 horas, entonces una hora incrementos hasta 24 horas.El controlo contará regresiva del tiempo restante hasta el inicio.

El tiempo elegido registrará en 5 segundos, y la sistema volverá automáticamente mostrar la temperatura anterior elegida o actual de la habitación una vez la unidad está encendida.(Cuando apaga la unidad, no muestra nada.)

Enciende la unidad o apagala en cualquier tiempo o modificar el reloj a 0.0, va a cancelar el programe de Auto

Empezar o Termimar el reloj.

CARACTERÍSTICAS DEL AIRE ACONDICIONADO

Pantallas:

Pantallas

Control de la salida de aire fresco

(bajo el modo de 10000~12000Btu/h):

PANTALLAS:

Muestra la temperatura en “°C”or “°F”y las opciones del

Auto-reloj.Cuando bajo el modo de ventilador sólo, muestra la temperatura actual de la habitación.

Los códigos de error:

AS-Sensor de error de la temperatura de la habitación- desenchufe la unidad y conéctala otra vez.Si repite este error, llama al servicio.

Sensor de error del evaporador de la temperatura-

Desenchufe la unidad y conéctala otra vez.Si el error repite, llama al servicio.

NOTA: “●”visualiza como se muestra en la imagen de la izquierda .

HS-El sensor de error de la calefacción eléctrica –

Desenchufe la unidad y la conecta.Si el error repite, llama al servicio.

NOTA:

Si la unidad falla inesperadamente por el corte de suministro eléctrico, volverá a encender con la opción de la función previa automáticamente cuando el suministro reanuda.

Rejillas de la dirección del aire

Plancas

Fig. A (VENTILACIÓN CERRADA) Fig. B (VENTILACIÓN ABIERTA)

La ventilación perimite al aire acondicionado a:

1. Recircula aire dentro-

ventilación cerrada

(Consulte Fig.A)

2. Saca el aire fresco en la

habitación-ventilación

abierta(consulte Fig.B)

3. Intercambia aire entre la

habitación y la fuera -

ventilación y salida abierta

(consulte Fig.C)

Fig. C (VENTILACIÓN & SALIDA

ABIERTA)

MANTENIMIENTO Y LIMPIEZA

Dirección del Aire

Las rejillas le permitan a dirigir el flujo de aire arriba o abajo

(bajo algunos modos) y a la izquierda o derecha en toda la habitación según la necesidad.Se puede obtener las direcciones izquierda y derecha.

Mueva las palancas de lado a lado hasta que se obtenga la dirección izquierda / derecha deseada.

INFORMACIÓN ADICIONAL QUE DEBE SABER

Ahora es dueño del producto operativo, hay más funciones bajo su controlo que debe familizarse con:

El circuito de Frío tiene un retraso de 3 minutos si la unidad enciende y apaga rápidamente Este evita el sobrecalentamiento del compresor y la posiblidad del disparo del disyuntor.El ventilador continuará funciona durante este tiempo.

El control es capaz de mostrar la temperatura en grados

Fahrenheit o grados Celsius.Para cambiar uno a otro, presiona y mentenga pulsando los botones izquierda y derecha de Temp/Timer al mismo tiempo durante 3 segundos.

CAUTION

Limpie su aire acondicionado de vez en cuando para mantenerlo un buen aspecto. Asegúrese de desenchufar la unidad antes de limpiarla para evitar el riesgo de cuña o incendio.

Limpieza del Filtro de Aire

El filtro de aire debe ser revisado al menos una vez al mes para ver si es necesario a limpiarlo. Las atrapadas partículas en el filtro podrán acumularse y causar una acumulación de escarchas en las bobinas de enfriamiento

MANTENIMIENTO Y LIMPIEZA

La Limpieza del Filtro de Aire

Empuje la palanca de ventilación en la posición de

Cerrada Vent (en su caso). Abra el panel frontal.

Tomar el filtro por el centro y tire hacia arriba y hacia fuera.

Lave el filtro con un liquid detergente para lavar los platos,en agua caliente..En juague el filtro.

Suavemente sacuda el exceso de agua del filtro.

Asegúrese de que el filtro está seco antes de volver.Si no, en lugar de lavar, podría aspirar el filtro.

Nota: Nunca usar el agua más caliente que 40°C

(104°F) a limpiar el filtro de aire.Nunca trata de operar la unidad sin el filtro.

SOLUCIONES DE PROBLEMAS

La Limpieza del Gabinete

Asegúrese de desconectar el AC para protegerlo de descarga eléctrica o incendio.El gabinete y su frontera pueden ser limpiado por un paño libre de aceite o un paño humedecido en agua caliente con liquid detergente para limpiar los platos.Enjuaquelo bien y séquelo.

Nunca use limpiadores abrasives, ceras ni pulimento en el frente del gabinete.

Asegúrese de quitar el agua en el paño antes de limpiar los controles.El exceso de agua dentro o alrededor del control podría causar daños al AC.

Enchufe el aparato.

Almacenamiento en en Invierno

Si va a almacenar el aire acondicionado durante el invierno, eliminelo de la ventana con mucho cuidado según las instrucciones de la instalación.

Cubralo con plástico o vuelvalo en la caja.

Antes de llamar al servicio, revisa esta lista.Le podría ahorrar tiempo y molestia.Esta lista incluye las ocurrencias communes, los cuales no son resultado por un defecto del hechura o los materiales de la fábrica.

Problema Solución

El aire acondicionado no funciona

Enchufe de pared desconectado.Presione el enchufe con mucha esfuerza en la toma de corriente.

El fusible domestico estropeado o disyuntor abierto.Reemplace fusible por un retardante o volver a encender el disyuntor.

Se desconecta el dispositivo de corriente.Presiona el botón RESET.

Se apague. Enciendalo.

La temperatura de la habitación está bajo 62°F(17°C). No empieza a enfriar hasta la tempetura llega más que 62°F(17°C).

El aire de la unidad no es tan fría Los elemtos del sensor de la temperatura detrás del filtro toca la bobina fría.Déjalo lejos de la bobina fría.

Ajuste a una temperatura más baja.

El compresro para cuando cambia el modo.Espere 3 minutos despúes de elegir el modo Frío.

El aire acondicionado enfria, pero la habitación hace calor – forma hielo en la bobina fría detrás el frente decorativo

La temperatura fuera está bajo 64°F(18°C). Para descongelar la bobina de O O, cambie al modo FAN ONLY.

El filtro de aire podría ser sucio.Limpie el filtro.Consulte la sección del Mantenimiento y Limpieza. Para descongelarlo, cambie al modo FAN ONLY.

El termostato ha ajustado demasiado frío durante su funcionamiento de la noche.Para descongelarla, cambie al modo FAN ONLY. Despúes, elige la una temperatura más alta.

SOLUCIONES DE PROBLEMAS

Problema Solución

El aire acondicionado enfria, pero la habitación hace mucho calor – no forma hielo en la bobina fría detrás el frente decorativo

Un seco filtro de air- aire limitado. Limpie el filtro. Consulte a la sección del

Mantenimiento y limpieza.

Ha elegido una temperatura tan alta, elige una temperatura baja.

Ha puesto la rejillas direccionales incorrectamente.. Ponga la rejilla en un lugar con mejor distribución del aire.

La frontera de la unidad está cubierta con cortinas, persianas, muebles, etc. – distribución de aire limitado.

Elimine la obstrucción en la frontera de la unidad.

Se escape el aire frío por las puertas, ventanas, rejillas, etc.Cierre la puerta, ventana o rejilla.

La uniadad funciona en una habitación caliente recientemente. Perimitalo un plazo de tiempo adicional para eliminar los calores guardados por los paredes, el techo, el suelo o los muebles.

El aire acondicionado se enciende y apaga rápidamente

Un seco filtro de aire- aire limitado. Limpie el filtro.

Hace ruido cuando la unidad enfria

El agua que gotea

INTERIOR cuando unidad está enfriando.

La temperatura fuera es demasiado alto. Elige la velocidad del FAN a una opción más alto para traer más aires pasando por la babina fría.

El sonido del movimiento del aire Es normal .Si hace tanto ruido, cambie a una opción de FAN más baja.

La vibración de la ventana – mala instalación. Consulte las instrucciones de instalación o consulte al instalador.

La instalación incorrecta. Inclina acondicionador de aire ligeramente hacia el exterior para permitir el drenaje del agua.Consulte las instrucciones de instalación - consulte con el instalador.

El agua que gotea

EXTERIOR cuando unidad está enfriando.

Unidad eliminar gran cantidad de humedad del ambiente húmedo. Esto es normal durante días excesivamente húmedos.

El control remoto no encuentra dentro del alcance. Coloque el control remoto dentro de 20 pies & 180º,radio de la parte frontal de la unidad.

Teledetección desactivación

Antes de tiempo

(algunos modelos)

Señal de control remoto obstruido. Retire la obstrucción.

Habitación demasiado fría

Ajuste la temperatura demasiado baja. Aumente la temperatura de la unidad.

GARANTIA DE AIR ACONDICIONADO

Su producto está protegido por esta garantía:

Reparaciones bajo garantía deben ser obtenidos de Centro de Servicios al Consumidor de Midea o con un administrador de Midea.

PERIODO DE

GARANTIA

GARANTIA

COMPLETA DE UNO

AÑOS

UNO la fecha de compra original

MIDEA , A TRAVES DE SU

CENTRO DE SERVICIO

AUTORIZADO, VA A

Pago de la totalidad de los costos de reparación o reemplazo de las partes de este dispositivo que se comprueba defectuosos en materiales o mano de obra.

EL CONSUMIDOR VA A SER

RESPONSABLE PARA

El transporte y los costos de las llamadas de servicio que se encuentra bajo

RESPONSABILIDADES

CONSUMIDOR NORMALES

DEL

Repuestos de Midea se utilizarán y se justifican únicamente por el período restante de la garantía original

Responsabilidades de los consumidores NORMALES

Esta garantía se aplica sólo a los productos de uso doméstico ordinario, y el consumidor es el responsable de los temas que figuran a continuación;

1. El uso adecuado del dispositivo, de conformidad con las instrucciones provistas con el producto.

2. Correcta instalación por un profesional de servicio autorizado, de conformidad con las instrucciones provistas con el dispositivo, y de conformidad con todos los plomería local , electricidad y / o códigos de gas.

3. Una buena conexión a tierra a una fuente de alimentación de voltaje suficiente, de sustitución de fusibles quemados, la reparación de los defectos sueltos o las conexiones de cableado en casa.

4. Los gastos para hacer que el dispositivo llegue al centro de la prestación de servicios.

5. Los daños a perfeccionar después de la instalación.

13

GARANTIA DE AIR ACONDICIONADO

1-866-646-4332.

14

El diseño y especificación se publican sin previo aviso de las mejoras del producto.

Consulte a la agencia de ventas o el fabricante sobre más informaciones.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement