ADJ QUAD SCAN PRO Specifications

QUAD SCAN PRO
©2013 ADJ Products, LLC all rights reserved. Information,
specifications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product.
User Instructions
7/13
Quad Scan Pro General Information
Unpacking: Thank you for purchasing the Quad Scan Pro by ADJ
Products, LLC®. Every Quad Scan Pro has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your fixture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without
contacting customer support first.
Introduction: The Quad Scan Pro is a DMX intelligent, RGBW “Quad
Color” LED scanner. The Quad Scan Pro can operate as a stand alone
fixture or in a Master/Slave configuration. The Quad Scan Pro has three
operating modes; sound active mode, show mode, and DMX control.
This fixture is suitable for theaters, studios, retail stores, and other
similar locations. For best results use fog or special effects smoke to
enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 2
Quad Scan Pro General Instructions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Quad Scan Pro •
•
•
•
•
•
•
Features
DMX-512 Protocol Compatible (1, 5, or 32 DMX Channels)
X/Y Mirror Control
3 Operating Modes - Sound Active, Show Mode, and DMX Control
Internal Microphone
Digital Display for Address and Function Setting
UC3 Controller (Not Included)
Power Cord Daisy Chaining (See page 22)
Quad Scan Pro
Warranty Registration
The Quad Scan Pro carries a 3 year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.
americandj.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ customer support for a R.A. number.
Quad Scan Pro Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to this unit.
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 3
Quad Scan Pro Safety Precautions
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to operate this unit if the power cord has been
frayed or broken.
•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 23 for cleaning details.
•Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 4
Quad Scan Pro Hanging Precautions
Fixture installation must always be secured with a secondary
safety attachment, such as an appropriate safety cable.
Regardless of the rigging option you choose for your Quad
Scan Pro always be sure to secure your fixture with a safety
cable (not included). Attach a safety cable to the provided
safety bolt.
Caution: For added protection mount the fixtures in areas outside of walking paths, seating areas, or areas were the fixture
might be reached by unauthorized personal.
Before mounting the fixture to any surface, make sure that the
installation area can hold a minimum point load of 10 times the
device’s weight.
To avoid injury, never stand directly below the device when
mounting, removing, or servicing the fixture.
Always use and install a safety cable ( not included) as a safety
measure to prevent accidental damage and/or injury in the
event the clamp fails.
Be sure to complete all rigging and installation procedures
before connecting the main power cord to the appropriate wall
outlet.
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 5
REMOTE
CONTROL
INPUT
SOUND
Quad Scan Pro
Set Up
OUTPUT
1
2
3
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 6
SOUN
Set Up
POWER
DMX+,DMX-,COMMON
cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
DMX512 OUT
3-PIN XLR
1
2
DMX +
3
DMX -
3
1
DMX512 IN
3-PIN XLR
2
3
1
2
Figure 2
XLR Female Socket
XLR Male Socket
1 Ground
2 Cold
2 Cold
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
1 Ground
XLR Pin Configuration
Pin 1 = Ground
REMOTE
CONTROL
SOUND
3 Hot
INPUT
OUTPUT
INPUT
Pin 2
= Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
POWER
Data Cable (DMX Cable) Requirements (For DMX and
Master/Slave
DMX512
DMX+,DMX-,COMMON
Operation): The Quad Scan Pro can be controlled
via DMX-512 protocol. The Quad Scan Pro can be a 1, 5, or 32 channel DMX unit. The
DMX address is set electronically using the controls on the bottom
panel of the unit. Your unit and your DMX controller require a approved DMX-512 110 Ohm Data
COMMON
cable for data input and data output (Figure 1). We
DMX +
DMX512 OUT
recommend Accu-Cable DMX cables. If you are
3-PIN XLR
DMX making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
Figure 1
a male and female XLR connector on either end of
OUTPUT
Notice: Be sure to follow
figures two and three when making your own
DMX512
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
INPUT
INPUT
POWER
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
REMOTE
CONTROL
INPUT
REMOTE
CONTROL
INPUT
SOUND
the cable. Also remember that DMX cable must be daisy chained and
cannot be split.
age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
SOUND
OUTPUT
Quad Scan Pro
Power Supply: The ADJ Quad Scan Pro contains a automatic volt-
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
INPUT
POWER
3
1
2
DMX512 IN
3-PIN XLR
3
1
2
POWER
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 7
Termination
avoids sign
and interfere
to connect a
120 Ohm 1/4
and PIN 3 (
Quad Scan Pro
Set Up
Quad Scan Pro
System Menu Chart
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Pin 4 - Do Not Use
Not Used
Pin 5 - Do Not Use
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 8
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 9
Quad Scan Pro
System Menu
Quad Scan Pro
System Menu
ADDR - DMX Address Setting.
0-16. Programs 0-16 are factory programs, while Show 0 is random
mode. Press the UP or DOWN buttons to find your desired show and
press the ENTER, then press and hold the MENU button for at least 3
seconds to confirm.
2. The current address will now be displayed and flashing. Press the
UP or DOWN buttons to find your desired address. Press ENTER to
set your desired DMX address.
SOUN - Sound Active mode. This mode will run in con-
1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is
displayed, press ENTER.
CHND - This will let select your desired DMX channel
mode.
1. Press the either the MENU button until “CHND” is displayed, press
ENTER. Either “1CH”, “5CH” or “32CH” will be displayed
2. Press the UP or DOWN buttons to find your desired DMX mode
and press ENTER to confim and exit.
SLND - This will let you set unit as a master or slave in
a master/slave configuration.
1. Press the MENU button until “SLND” is displayed, press ENTER.
Either “MAST”, “SL 1” or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim.
NOTE: In a Master/Slave configuration you can set one fixture to
Master or Slave 1 (SL 1) and then set the next fixture to Slave 2 (SL
2), in doing this the fixtures will now have contrast movement to each
other.
SHND: SH 0 - SH16 - Show modes 0-16 (Factory
programs). Show mode can be run with sound activity or
without. For show mode to run without sound activity turn
sound activity off.
1. Press the MENU button until “SHND” is displayed, press ENTER.
2. “Sh X” will now be displayed, “X” representing a number between
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 10
junction with show mode.
1. Press the MENU button until “SOUN” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode, or
“OFF” to deactivate sound active mode.
3. Press the ENTER, and then press and hold the MENU button for at
least 3 seconds to confirm.
SENS - Sound sensitivity control.
1. Press the MENU button until “SENS” is displayed, press ENTER.
2. The display will show a number between 0-100. Press the UP or
DOWN buttons to adjust the sound sensitivity. 0 being the least sensitive and 100 the most sensitive.
3. Press the ENTER button to confirm.
DNST - This mode can be used as a precaution mode, that
in case the DMX signal is lost, the operating mode chosen
in the setup is the running mode the fixture will go into when
the DMX signal is lost. You can also set this as the operating mode you would like the unit to return to when power is
applied.
1. Press the MENU button until “DNST” is displayed, press ENTER.
2. Either “MASL”, “BLND”, or “LAST” will be displayed. Choose an
operating mode you would like the unit to start up in when power is
applied or the DMX signal is lost.
• MASL (Master Slave) - If the DMX signal is lost or power is applied,
the unit will automatically go into Master Slave mode.
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 11
Quad Scan Pro
System Menu
• BLND (Blackout) - If the DMX signal is lost or power is applied, the
unit will automatically go into stand by mode.
• LAST (Last State) - If the DMX signal is lost the fixture will stay in the
last DMX set up. If power is applied and this mode is set, the unit will
automatically go into the last DMX set up.
3. Press ENTER to confirm your desired set up.
LED - With this function you can have the LED display
turn off after 10 seconds.
1. Press the MENU button until “LED” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at all
times, or “OFF” to switch to have the LED display switch off after 10
seconds.
3. Press the ENTER button to confirm.
PAN - Pan Inversion
1. Tap the MENU button until “PAN” is displayed, press ENTER.
Either Yes or No will be displayed.
2. To activate the Pan inversion tap the UP or DOWN buttons until
YES is displayed, press ENTER to confim. To deactivate Pan inversion, select NO and press Enter.
TILT - Tilt Inversion
1. Tap the MENU button until “TILT” is displayed, press ENTER.
Either YES or NO will be displayed.
2. To activate the Tilt inversion tap the UP or DOWN buttons until
YES is displayed, press ENTER to confim. To deactivate Tilt inversion, select NO and press Enter.
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 12
Quad Scan Pro
System Menu
DISP - This will “flip” the LED display 180º.
1. Press the MENU button until “dISP” is displayed, press ENTER.
2. Either “dISP” or “dSIP” will now be displayed. Press the UP or
DOWN buttons to select one or the other.
3. Press the ENTER button to confirm.
TEST - This function will run a auto test program.
1. Press the MENU button until “TEST” is displayed, press ENTER.
2. The fixture will now run a auto test.
FHRS - With this function you can display the running
time of the fixture.
1. Press the MENU button until “FHRS” is displayed, press ENTER.
2. The running time of the fixture will now be displayed. Press MENU
to exit.
VER - With this function you can display the version software of the fixture.
1. Press the MENU button until “VER” is displayed, press ENTER.
2. The software version will now be displayed. Press MENU to exit.
RSET - Use this function to reset the unit.
1. Press the MENU button until “RSET” is displayed, press ENTER.
2. The fixture will now reset.
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 13
Quad Scan Pro
Operation
Universal DMX Control: This function allows you to use a universal DMX-512 controller to control the chases and patterns, dimmer
and strobe. A DMX controller allows you to create unique programs
tailored to your individual needs.
1. The Quad Scan Pro can be a 1, 5, or 32 DMX channel fixture. See pages 16-21 for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 6-8 as well as the set-up specifications that are includ ed with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. Follow the instructions on page 10 to set the DMX address.
5. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
6. For help operating in DMX mode consult the manual included with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
Note: This mode runs in conjuction with show mode. You should
select a show previous to activating sound active mode.
1. Press the MENU button until “SOUN” is displayed, and press ENTER.
2. Press the UP or DOWN buttons so that “ON” is displayed, and press ENTER to confirm and then hold MENU for at least 2-3 sec-
onds.
3. To adjust the sound sensitivity press the MENU button until “SENS” is displayed and press ENTER. Use the UP or DOWN
buttons to adjust sensitivity.
4. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout. See page 16 for UC3 controls and functions.
Quad Scan Pro
3.
Operation
confirm. See pages 10-11 for more info.
The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout. See page 16 for UC3 controls and functions.
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth- er via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit find your desired show and set that show by pressiing the ENTER button. After you have set your desired
show, press the MENU button until “SLND” is displayed, and Press
ENTER. Press the UP or DOWN buttons until “MAST” is dis-
played, and press ENTER to confirm.
3. On the slave units press the MENU button until “SLND” is dis-
played, and press ENTER. Press the UP or DOWN buttons until either “SL 1” or “SL 2” is displayed, choose your desired slave mode and press ENTER to confirm.
4. The slave units will now follow the Master unit.
NOTE: In a Master/Slave configuration you can set one fixture to
Master or Slave 1 (SL 1) and then set the next fixture to Slave 2 (SL
2), in doing this the fixtures will now have contrast movement to each
other.
Show Mode: In this mode you can select 1 of 16 shows to run. This
mode can run as just an ordinary show, or with sound active mode.
1. Press the MENU button until “SHND” is displayed, and press ENTER.
2. Press the UP or DOWN buttons until you find your desired show, and press ENTER then press and hold MENU for 3 seconds to ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 14
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 15
Quad Scan Pro
Channel
1
Value
0-7
8 - 22
23 - 37
38 - 52
53 - 67
68 - 82
83 - 97
98 - 112
113 - 127
128 - 142
143 - 157
158 - 172
173 - 187
188 - 202
203 - 217
218 - 232
233 - 247
248 - 255
1 Channel Mode - DMX Traits
Function
Channel
SHOWS
BLACKOUT
SHOW 1
SHOW 2
SHOW 3
SHOW 4
SHOW 5
SHOW 6
SHOW 7
SHOW 8
SHOW 9
SHOW 10
SHOW 11
SHOW 12
SHOW 13
SHOW 14
SHOW 15
SHOW 16
SOUND ACTIVE SHOWS 1-16
1
Quad Scan Pro
UC3 Control
Blackout Blackout the unit
1.White LED Strobe
Select Show
Function 2.White LED Strobe by sound
(Show 1-16)
3. Multicolor Strobe by sound
Mode
Sound/Strobe
(LED ON)
Quad Scan Pro
Show
(LED Blinking)
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 16
2
3
4
Value
0-7
8 - 22
23 - 37
38 - 52
53 - 67
68 - 82
83 - 97
98 - 112
113 - 127
128 - 142
143 - 157
158 - 172
173 - 187
188 - 202
203 - 217
218 - 232
233 - 247
248 - 255
0 - 255
0 - 255
0-8
9 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
5 Channel Mode - DMX Traits
Function
PAN/TILT MOVEMENTS
NO MOVEMENT
MOVEMENT 1
MOVEMENT 2
MOVEMENT 3
MOVEMENT 4
MOVEMENT 5
MOVEMENT 6
MOVEMENT 7
MOVEMENT 8
MOVEMENT 9
MOVEMENT 10
MOVEMENT 11
MOVEMENT 12
MOVEMENT 13
MOVEMENT 14
MOVEMENT 15
MOVEMENT 16
SOUND ACTIVE
PAN/TILT SPEED MOVEMENT
SLOW - FAST
MASTER DIMMER
0% - 100%
STROBING
OPEN
STROBING SLOW - FAST
OPEN
SLOW OPEN - FAST CLOSE
OPEN
FAST OPEN - SLOW CLOSE
OPEN
SOUND ACTIVE STROBING
OPEN
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 17
Quad Scan Pro
Channel
5
Value
0-7
8 - 15
16 - 23
24 - 31
32 - 39
40 - 47
48 - 55
56 - 63
64 - 71
72 - 79
80 - 87
88 - 95
96 - 103
104 - 111
112 - 119
120 - 127
128 - 135
136 - 143
144 - 151
152 - 159
160 - 167
168 - 175
176 - 183
184 - 191
192 - 199
200 - 207
208 - 215
216 - 223
224 - 231
232 - 239
240 - 247
248 - 255
5 Channel Mode - DMX Traits
Quad Scan Pro
Function
Channel
STATIC COLOR SEQUENCE
COLOR SEQUENCE 1
COLOR SEQUENCE 2
COLOR SEQUENCE 3
COLOR SEQUENCE 4
COLOR SEQUENCE 5
COLOR SEQUENCE 6
COLOR SEQUENCE 7
COLOR SEQUENCE 8
COLOR SEQUENCE 9
COLOR SEQUENCE 10
COLOR SEQUENCE 11
COLOR SEQUENCE 12
COLOR SEQUENCE 13
COLOR SEQUENCE 14
COLOR SEQUENCE 15
COLOR SEQUENCE 16
COLOR SEQUENCE 17
COLOR SEQUENCE 18
COLOR SEQUENCE 19
COLOR SEQUENCE 20
COLOR SEQUENCE 21
COLOR SEQUENCE 22
COLOR SEQUENCE 23
COLOR SEQUENCE 24
COLOR SEQUENCE 25
COLOR SEQUENCE 26
COLOR SEQUENCE 27
COLOR SEQUENCE 28
COLOR SEQUENCE 29
COLOR SEQUENCE 30
COLOR SEQUENCE 31
COLOR SEQUENCE 32
1
2
3
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 18
4
5
6
7
8
9
10
11
12
13
14
15
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0-8
9 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
32 Channel Mode - DMX Traits
Function
MIRROR 1 PAN
MIRROR 1 TILT
RED (MIRROR 1)
0% - 100%
GREEN (MIRROR 1)
0% - 100%
BLUE (MIRROR 1)
0% - 100%
WHITE (MIRROR 1)
0% - 100%
MASTER DIMMER (MIRROR 1)
0% - 100%
STROBING (MIRROR 1)
OPEN
STROBING SLOW - FAST
OPEN
FAST CLOSE - SLOW OPEN
OPEN
SLOW CLOSE - FAST OPEN
OPEN
SOUND ACTIVE STROBING
OPEN
MIRROR 2 PAN
MIRROR 2 TILT
RED (MIRROR 2)
0% - 100%
GREEN (MIRROR 2)
0% - 100%
BLUE (MIRROR 2)
0% - 100%
WHITE (MIRROR 2)
0% - 100%
MASTER DIMMER (MIRROR 2)
0% - 100%
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 19
Quad Scan Pro
Channel
16
17
18
19
20
21
22
23
24
25
Value
0-8
9 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0-8
9 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
0 - 255
32 Channel Mode - DMX Traits
Quad Scan Pro
Function
Channel
STROBING (MIRROR 2)
OPEN
STROBING SLOW - FAST
OPEN
FAST CLOSE - SLOW OPEN
OPEN
SLOW CLOSE - FAST OPEN
OPEN
SOUND ACTIVE STROBING
OPEN
MIRROR 3 PAN
MIRROR 3 TILT
RED (MIRROR 3)
0% - 100%
GREEN (MIRROR 3)
0% - 100%
BLUE (MIRROR 3)
0% - 100%
WHITE (MIRROR 3)
0% - 100%
MASTER DIMMER (MIRROR 3)
0% - 100%
STROBING (MIRROR 3)
OPEN
STROBING SLOW - FAST
OPEN
FAST CLOSE - SLOW OPEN
OPEN
SLOW CLOSE - FAST OPEN
OPEN
SOUND ACTIVE STROBING
OPEN
MIRROR 4 PAN
26
27
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 20
28
29
30
31
32
Value
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0-8
9 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
32 Channel Mode - DMX Traits
Function
MIRROR 4 TILT
RED (MIRROR 4)
0% - 100%
GREEN (MIRROR 4)
0% - 100%
BLUE (MIRROR 4)
0% - 100%
WHITE (MIRROR 4)
0% - 100%
MASTER DIMMER (MIRROR 4)
0% - 100%
STROBING (MIRROR 4)
OPEN
STROBING SLOW - FAST
OPEN
FAST CLOSE - SLOW OPEN
OPEN
SLOW CLOSE - FAST OPEN
OPEN
SOUND ACTIVE STROBING
OPEN
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 21
Quad Scan Pro
Gobo Replacement
The Quad Scan Pro comes with 4 replaceable gobos. This gobos can
be interchanged at any time and allows you to customize your system.
To replace gobo;
1. Select the gobo you would like to replace and unscrew the thumb screw that is holding the gobo housing in place. Note: The thumb screw cannot be removed.
2. Remove the gobo housing.
3. Once the gobo housing has been removed, remove the retaining
ring that holds the gobo in. This can easily be done using needle nose pliers.
4. Remove and replace the gobo with your desired replacement. Reinsert the retainer ring, and make sure the ring rests firmly against the gobo.
5. Slide the gobo houseing back into place, and secure the housing by tighting the thumb screw.
Quad Scan Pro
Power Cord Daisy Chain
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 4 fixtures maximum. After 4 fixtures you will need
to use a new power outlet. They must be the same fixtures. DO
NOT mix fixtures.
Quad Scan Pro
Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that
the fuse holder is located inside the power socket. Insert a flat-head
screw driver into the power socket and gently pry out the fuse holder.
Remove the bad fuse and replace with a new one. The fuse holder also
has a holder for a spare fuse.
Quad Scan Pro Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning
the internal and external optical lenses and mirror should be carried
out periodically to optimize light output. Cleaning frequency depends
on the environment in which the fixture operates (I.e. smoke, fog
residue, dust, dew). In heavy club use we recommend cleaning on a
monthly basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Always be sure to dry all parts completely before plugging the unit back in.
Quad Scan Pro Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1.Be sure the external fuse has not blown. The fuse is located on the rear panel of the unit.
2.Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 22
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 23
Quad Scan Pro Warranty
Quad Scan Pro Notes
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested
repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC
will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LED and lamps)
• Laser Products = 90-Day Limited Warranty
• L.E.D. Products = 3-year (1095 days) Limited Warranty (excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty). Only the L.E.D.s carry a 3-year warranty
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 24
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 25
Quad Scan Pro Model: Specifications
Quad Scan Pro
Voltage:
100~240V 50Hz/60Hz
LEDs:
4 X 10 Watt 4-in-1 RGBW LEDs
Power Cord Daisy Chain: 4 Fixtures Max.
Power Consumption:
88W
Dimensions: 17.25”(L) x 14.25”(W) x5.25”(H)
438mm x 356mm x 133mm
Colors:
RGBW
Gobos:4
Gobo Size:
20.5mm
12mm (Viewable)
Weight:
17 Lbs. / 7.5 kgs.
Fuse:
7 Amp
Duty Cycle:
None
DMX: 1, 5, & 32 DMX Channel Modes
Sound Active:
Yes
Working Position:
Any Safe, Secure Position
Warranty:
3 Year (1095 days)
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
ADJ Products, LLC - www.adj.com - Quad Scan Pro Instruction Manual Page 26
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@adj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adj.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99