DMT2420B
DMT2420R
DMT2420S
SERVICE MANUAL
S12M201DMT24E
MICROWAVE OVEN
MODELS
DMT2420B
DMT2420R
DMT2420S
In the interest of user-safety the oven should be restored to its original condition and only parts identical to those specified should
be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage
and current. Contact with the following parts may result in a severe, possibly fatal, electrical shock. (Inverter unit
that includes High Voltage Capacitor, High Voltage Power Transformer, High Voltage Rectifier and Heat sink etc.,
and Magnetron, High Voltage Harness etc..)
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ...................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................1
MICROWAVE MEASUREMENT PROCEDURE .....................................................................................................2
FOREWORD AND WARNING ................................................................................................................................3
PRODUCT SPECIFICATIONS ...............................................................................................................................4
GENERAL INFORMATION ...................................................................................................................................5
OPERATION .........................................................................................................................................................6
TROUBLESHOOTING GUIDE ............................................................................................................................. 10
TEST PROCEDURE ............................................................................................................................................ 11
TOUCH CONTROL PANEL ASSEMBLY ............................................................................................................. 26
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE .................................................................. 27
PICTORIAL DIAGRAM ........................................................................................................................................ 33
POWER UNIT CIRCUIT ....................................................................................................................................... 34
LSI UNIT CIRCUIT ............................................................................................................................................... 35
PRINTED WIRING BOARD ................................................................................................................................. 36
PARTS LIST ........................................................................................................................................................ 37
PACKING AND ACCESSORIES ......................................................................................................................... 41
dis tinctive appliances
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
DMT2420B
DMT2420R
DMT2420S
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave
source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing
surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of
dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity,
and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and
transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the
oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be performed
on each oven prior to release to the owner.
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact DACOR immediately @
1-800-793-0093.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven and
2) contact DACOR and Food and Drug Administration's Center for Devices and Radiological Health
immediately.
Service personnel should inform DACOR of any certified unit found with emissions in excess of 4mW/cm2.
The owner of the unit should be instructed not to use the unit until the oven has been brought into compliance.
DANGER CAUTION
HIGH VOLTAGE
Do not energize a microwave oven with the outer case cabinet removed, because a microwave oven
generates High Voltage in the circuit.
If you intend to operate the oven employing the high frequency switching power converter circuit, you should
take special precautions to avoid an electrical shock hazard.
The high voltage transformer, high voltage capacitor and high voltage diode have energized high voltage
potential approx. 8 KV.
The aluminium heat sink is connected to the switching power transistor Collector pole, and has an energized
high voltage potential approx. 650V peak.
DO NOT ACCESS THE HIGH VOLTAGE TRANSFORMER, HIGH VOLTAGE CAPACITOR, HIGH
VOLTAGE DIODE AND HEAT SINK WHEN THE POWER SUPPLY IS CONNECTED TO AN ELECTRICAL
OUTLET.
DMT2420B
DMT2420R
DMT2420S
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
When the testing is completed,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
Before Servicing
1. Disconnect the power supply cord
remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
, and then
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
After repairing
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for 60
seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an
insulated screwdriver.
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
Whenever troubleshooting is performed the power supply
must be disconnected. It may, in some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that the leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out Before Servicing procedure and reexamine the connections to the component being tested.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and a microwave leakage test should be carried out.
1
DMT2420B
DMT2420R
DMT2420S
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches Primary interlock relay and door sensing switch shall prevent microwave radiation emission in
excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission
in excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for
microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5½C (68½F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.)
and made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode.
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed,
replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on
the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the secondary interlock switch does turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
DMT2420B
DMT2420R
DMT2420S
SERVICE MANUAL
dis tinctive appliances
PRODUCT DESCRIPTION
MICROWAVE OVEN
DMT2420B/DMT2420R/DMT2420S
GENERAL INFORMATION
FOREWORD
This Manual has been prepared to provide Dacor Service Personnel
with Operation and Service Information for the DACOR MICROWAVE OVENS, DMT2420B, DMT2420R and DMT2420S.
OPERATION
It is recommended that service personnel carefully study the entire text
of this manual so that they will be qualified to render satisfactory
customer service.
TROUBLESHOOTING GUIDE AND
TEST PROCEDURE
Check the interlock switches and the door seal carefully. Special
attention should be given to avoid electrical shock and microwave
radiation hazard.
TOUCH CONTROL PANEL
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
COMPONENT REPLACEMENT
AND ADJUSTMENT PROCEDURE
WIRING DIAGRAM
Servicing and repair work must be carried out only by trained service
personnel.
DANGER
Certain initial parts are intentionally not grounded and present
a risk of electrical shock only during servicing. Service personnel - Do not contact the following parts while the appliance
is energized;
High Voltage Capacitor, Power Transformer, Magnetron, High
Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more than
250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “∆” on parts list may cause undue microwave
exposure, by themselves, or when they are damaged, loosened or
removed.
dis tinctive appliances
1440 Bridge Gate Dr.
Diamond Bar, CA 91765
3
PARTS LIST
DMT2420B
DMT2420R
DMT2420S
SPECIFICATION
ITEM
DESCRIPTION
Power Requirements
120 Volts / 14.3 Amperes
60 Hertz
Single phase, 3 wire grounded
Power Output
1200 watts (IEC TEST PROCEDURE)
Operating frequency of 2450MHz
Case Dimensions
Width
24"
Height 13-3/8"
Depth 19-1/8"
Cooking Cavity Dimensions
Width 17-3/8"
Height 10-1/2"
Depth 18-5/8"
2.0 Cubic Feet
Control Complement
Touch Control System
Clock ( 1:00 - 12:59 )
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
100 PERCENT.............................. Full power throughout the cooking time
90 PERCENT ............................................... approx. 90% of Full Power
80 PERCENT ............................................... approx. 80% of Full Power
70 PERCENT ............................................... approx. 70% of Full Power
60 PERCENT ............................................... approx. 60% of Full Power
50 PERCENT ............................................... approx. 50% of Full Power
40 PERCENT ............................................... approx. 40% of Full Power
30 PERCENT .............................................. approx. 30% of Full Power
20 PERCENT ............................................... approx. 20% of Full Power
10 PERCENT ............................................... approx. 10% of Full Power
0 PERCENT ................................ No power throughout the cooking time
Sensor modes pads, Microwave Recipes & Instruction pad, Defrost pad,
Beverage pad, Set Up pad, Number selection pads, Easy Minute pad,
Stop/Clear pad, Start pad, New Wave Cookbook pads.
Oven Cavity Light
Yes
Safety Standard
UL Listed
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed
and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.
WARNING: Improper use of the grounding plug can result in a risk of electric shock.
Electrical Requirements
The electrical requirements are a 120 volt 60 Hz, AC only, 15 or 20 amp. fused electrical supply. It is recommended that a
separate circuit serving only this appliance be provided. When installing this appliance, observe all applicable codes and
ordinances.
A short power-supply cord is provided to reduce risks of becoming entangled in or tripping over a longer cord.
4
DMT2420B
DMT2420R
DMT2420S
Where a two-pronged wall-receptacle is encountered, it is the personal
responsibility and obligation of the customer to contact a qualified
electrician and have it replaced with a properly grounded three-pronged
wall receptacle or have a grounding adapter properly grounded and
polarized. If the extension cord must be used, it should be a 3-wire, 15
amp. or higher rated cord. Do not drape over a countertop or table where
it can be pulled on by children or tripped over accidentally.
Grounded
Receptacle Box
3-Pronged
Plug
CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND GROUNDING PRONG FROM THIS
PLUG.
OVEN DIAGRAM
5
6
7
9
2
11
8
10
1
4
3
Grounding Pin
3-Pronged Receptacle
1. One touch door open button.
Push to open door.
2. Door latches.
The oven will not operate unless
the door is securely closed.
3. Removable turntable support.
4. Removable turntable.
The turntable will rotate
clockwise or counterclockwise.
5. Oven lamp.
It will light when oven is operating
or door is opened.
6. Oven door with see-through
window.
7. Ventilation openings. (Rear)
8. Auto-Touch control panel.
9. Time display: Digital display, 99
minutes 99 seconds.
10. Wave guide cover.
11. Power supply cord.
TOUCH CONTROL PANEL
NOTE:
The directed features are disabled
after three minutes when the oven
is not in use. These features are
automatically enabled when the
door is opened and closed or the
STOP/ CLEAR pad is pressed.
DMT2420R
DMT2420B
DMT2420S
5
DMT2420B
DMT2420R
DMT2420S
OPERATION
DESCRIPTION OF OPERATING SEQUENCE
The following is a description of component functions during
oven operation.
4. The microwave energy produced by the magnetron is
channelled through the waveguide into the cavity feedbox, and then into the cavity where the food is placed to
be cooked.
5. Upon completion of the cooking time, the power
transformer, oven lamp, etc. are turned off, and the
generation of microwave energy is stopped. The oven will
revert to the OFF condition.
6. When the door is opened during a cook cycle, the monitor
switch, door sensing switch, secondary interlock switch,
relay (RY1) and primary interlock relay are activated with
the following results. The circuits to the turntable motor,
the cooling fan motor, and the high voltage components
are de-energized, the oven lamp remains on, and the
digital read-out displays the time still remaining in the
cook cycle when the door was opened.
7. The monitor switch electrically monitors the operation of
the secondary interlock switch and primary interlock relay
and is mechanically associated with the door so that it will
function in the following sequence.
(1) When the door opens from the closed position, the primary
interlock relay (RY2) and secondary interlock switch open
their contacts. And contacts of the relay (RY1) remains
closed. Then the monitor switch contacts close.
(2) When the door is closed from the open position, the
monitor switch contacts open first. Then the contacts of
the secondary interlock switch and door sensing switch
close. And contacts of the relay (RY1) open.
If the secondary interlock switch and primary interlock relay
(RY2) fail with the contacts closed when the door is opened,
the closing of the monitor switch contacts will form a short
circuit through the monitor fuse, secondary interlock switch,
relay (RY1) and primary interlock relay (RY2), causing the
monitor fuse to blow.
OFF CONDITION
Closing the door activates the door sensing switch and
secondary interlock switch. (In this condition, the monitor
switch contacts are opened.)
When oven is plugged in, 120 volts A.C. is supplied to the
control unit. (Figure O-1).
1. "Set clock" key and "Video demo" key will be appeared
on the touch screen.
2. Touch "Set clock" key and set the clock referring to the
operation manual.
NOTE: If any keys are not touched for 30 seconds, the touch
screen will go on to the Video Demo mode. To cancel
the Video Demo mode, touch the STOP/CLEAR pad.
And then set the clock.
3. The touch screen will show the home page after setting
the clock.
4. The following is the example of the Home page in the
case the time of the day is set to 12:30 p.m..
12 : 30 PM
1
2
3
4
5
6
7
8
9
0
Kitchen
Timer
Time
Select
NOTE: Even if the clock is not set, the display will show the
Home page by touching the STOP/CLEAR pad within
30 seconds after plugged in.
COOKING CONDITION
Program desired cooking time by touching the NUMBER
pads. Program the power level by touching the POWER
LEVEL pad.
When the START pad is touched, the following operations
occur:
POWER LEVEL 0% TO 100% COOKING
When Variable Cooking Power is programmed, the 120 volts
A.C. is supplied to the power transformer intermittently
through the contacts of relay (RY-2) which is operated by the
control unit within a 32 second time base. Microwave power
operation is as follows:
1. The contacts of relays are closed and components
connected to the relays are turned on as follows.
(For details, refer to Figure O-2)
RELAY
RY-1
RY-2
VARI-MODE
CONNECTED COMPONENTS
oven lamp/turntable motor/fan motor
power transformer
2. 120 volts A.C. is supplied to the primary winding of the
power transformer and is converted to about 3.2 volts A.C.
output on the filament winding, and approximately 2360
volts A.C. on the high voltage winding.
3. The filament winding voltage heats the magnetron filament
and the H.V. winding voltage is sent to a voltage doubler
circuit.
OFF TIME
100% power
32 sec.
0 sec.
approx. 90% power
30 sec.
2 sec.
approx. 80% power
26 sec.
6 sec.
approx. 70% power
24 sec.
8 sec.
approx. 60% power
22 sec.
10 sec.
approx. 50% power
18 sec.
14 sec.
approx. 40% power
16 sec.
16 sec.
approx. 30% power
12 sec.
20 sec.
approx. 20% power
8 sec.
24 sec.
approx. 10% power
0% power
6
ON TIME
6 sec.
26 sec.
0 sec.
32 sec.
DMT2420B
DMT2420R
DMT2420S
Note:
Cooking Sequence.
1. Touch one of the SENSOR pads and then touch the Start
pad.
NOTE: The oven should not be operated on SENSOR
immediately after plugging in the unit. Wait two
minutes before cooking on SENSOR.
2. The coil of shut-off relay (RY-1) is energized, the turntable
motor, oven lamp and cooling fan motor are turned on, but
the power transformer is not turned on.
3. After about 16 seconds, the cook relay (RY-2) is energized.
The power transformer is turned on, microwave energy is
produced and first stage is started.
The 16 seconds is the cooling time required to remove any
vapor from the oven cavity and sensor.
NOTE: During this first stage, do not open the door or touch
STOP/CLEAR pad.
4. When the sensor detects the vapor emitted from the food,
the display switches over to the remaining cooking time
and the timer counts down to zero.
At this time, the door may be opened to stir, turn, or
season food.
5. When the timer reaches zero, an audible signal sounds.
The shut-off relay and cook relay are de-energized and the
power transformer, oven lamp, etc. are turned off.
6. Opening the door or touching the STOP/CLEAR pad, the
time of day will reappear on the display and the oven will
revert to an OFF condition.
The ON/OFF time ratio does not correspond with the
percentage of microwave power, because approx. 2
seconds are needed for heating of the magnetron
filament.
SENSOR COOKING CONDITION
Using the SENSOR function, the food is cooked without
figuring time, power level or quantity. When the oven senses
enough steam from the food, it relays the information to its
microprocessor which will calculate the remaining cooking
time and power level needed for best results. When the food
is cooked, water vapor is developed. The sensor “senses” the
vapor and its resistance increases gradually. When the
resistance reaches the value set according to the menu,
supplementary cooking is started.
The time of supplementary cooking is determined by experiment with each food category and inputted into the LSI.
An example of how sensor works: (POTATOES)
1. Potatoes at room temperature. Vapor is emitted very
slowly.
MIC
RO
WA
VE
2. Heat Potatoes. Moisture and humidity is emitted rapidly.
You can smell the aroma as it cooks.
AH SENSOR
MIC
RO
WA
VE
3. Sensor detects moisture and humidity and calculates
cooking time and variable power.
7
DMT2420B
DMT2420R
DMT2420S
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CLOCK APPEARS ON DISPLAY.
NOTE:
Indicates components with potential above 250 V.
C/T
FUSE
BLK
RED
COM
N.O.
HUMIDITY
SENSOR
F3
A2
(RY2)
PRIMARY
INTERLOCK
RELAY
(RY1)
POWER
TRANSFORMER
F2
F1
H
A1
RED
RED
DOOR
SENSING
SWITCH
N.C.
MONITOR
SWITCH
FAN
MOTOR
COM
WHT
BLU
ORG
TURN
TABLE
MOTOR
WHT
OVEN
LAMP
HIGH
VOLTAGE
CAPACITOR
N.O.
FM
TTM
WHT
WHT
WHT
OL
B2
B1
BLU
BRN
ORG
ORG
CAVITY
TEMP
FUSE
RED
COM
WHT
N.O.
BRN
GRY/WHT
CONTROL UNIT
MAGNETRON
GND
WHT
120V AC
60Hz
N
GRN
HIGH
VOLTAGE
RECTIFIER
N.O.
COM
SECONDARY
INTERLOCK
SWITCH
Figure O-1. Oven Schematic-Off Condition
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. COOKING TIME PROGRAMMED.
3. VARIABLE COOKING CONTROL "P-HI/ 100 PERCENT".
4. "START" PAD TOUCHED.
C/T
FUSE
BLK
RED
COM
N.O.
F3
A2
(RY2)
PRIMARY
INTERLOCK
RELAY
(RY1)
POWER
TRANSFORMER
F2
F1
H
A1
HUMIDITY
SENSOR
RED
RED
OVEN
LAMP
COM
ORG
TURN
TABLE
MOTOR
DOOR
SENSING
SWITCH
FM
FAN
MOTOR
B2
HIGH
VOLTAGE
CAPACITOR
N.O.
N.C.
MONITOR
SWITCH
N.O.
SECONDARY
INTERLOCK
SWITCH
Figure O-2. Oven Schematic-Cooking Condition
8
COM
WHT
BLU
ORG
B1
BLU
BRN
HIGH
VOLTAGE
RECTIFIER
MAGNETRON
COM
WHT
TTM
WHT
WHT
OL
RED
N.O.
BRN
ORG
CAVITY
TEMP
FUSE
CONTROL UNIT
WHT
WHT
GND
WHT
GRY/WHT
120V AC
60Hz
N
GRN
DMT2420B
DMT2420R
DMT2420S
DESCRIPTION AND FUNCTION OF COMPONENTS
DOOR OPEN MECHANISM
3. If the door is opened, and the primary interlock relay (RY2)
and secondary interlock switch contacts fail to open, the
C/T fuse blows simultaneously with closing of the monitor
switch contacts.
CAUTION: BEFORE REPLACING A BLOWN C/T FUSE
TEST THE DOOR SENSING SWITCH, PRIMARY INTERLOCK RELAY (RY2), RELAY
(RY1), SECONDARY INTERLOCK SWITCH AND
MONITOR SWITCH FOR PROPER OPERATION. (REFER TO CHAPTER "TEST PROCEDURE").
NOTE: C/T FUSE AND MONITOR SWITCH ARE
REPLACED AS AN ASSEMBLY.
The door is opened by pushing the open button on the control
panel, refer to the Figure D-1. When the open button is
pushed, the open button pushes up the switch lever, and then
the switch lever pushes up the latch head. The latch heads
are moved upward and released from latch hook. Now the
door will open.
Latch Heads
Door
Door Sensing
Switch
TURNTABLE MOTOR
The turntable motor rotates the turntable located on the
bottom of the oven cavity, so that the foods on the turntable
cook evenly during cooking. The turntable may turn in either
direction.
Monitor Switch
Switch Lever
Secondary Interlock
Switch
COOLING FAN MOTOR
The cooling fan motor drives a blade which draws external cool
air. This cool air is directed through the air vanes surrounding
the magnetron and cools the magnetron. This air is channeled
through the oven cavity to remove steam and vapors given off
from the heating foods. It is then exhausted through the
exhausting air vents at the oven cavity.
Figure D-1. Door Open Mechanism
DOOR SENSING AND SECONDARY INTERLOCK
SWITCHES
The secondary interlock switch is mounted in the lower
position of the latch hook and the door sensing switch in the
secondary interlock system is mounted in the upper position
of the latch hook. They are activated by the latch heads on
the door. When the door is opened, the switches interrupt the
power to all high voltage components. A cook cycle cannot
take place until the door is firmly closed thereby activating
both interlock switches. The secondary interlock system
consists of the door sensing switch and secondary interlock
relay located on the control circuit board.
CAVITY TEMPERATURE FUSE
The cavity temperature fuse located on the top of the oven
cavity, is designed to prevent damage to the oven by fire. If the
food load is overcooked, by either error in cook time or defect
in the control unit, the cavity temperature fuse will open.
Under normal operation, the cavity temperature fuse remains
closed. However, when abnormally high temperatures are
reached within the oven cavity, the cavity temperature fuse will
open at 302OF(150OC) causing the oven to shut down.
NOTE: This is fuse. It does not reset.
MONITOR SWITCH
C/T TEMPERATURE FUSE
The monitor switch is activated (the contacts opened) by the
latch head on the door while the door is closed. The switch is
intended to render the oven inoperative, by means of blowing
the C/T fuse, when the contacts of the primary interlock relay
(RY2) and secondary interlock switch fail to open when the
door is opened.
The C/T fuse located near the magnetron is designed to prevent
damage to the magnetron if an over heated condition develops
in the tube due to cooling fan failure, obstructed air guide, dirty
or blocked air intake, etc.
Under normal operation, the C/T fuse remains closed. However, when abnormally high temperatures are reached within
the magnetron, the C/T fuse will open at 302OF(150OC) causing
the oven to shut down.
1. The C/T fuse blows when the contacts (COM-NO) of the
primary interlock relay (RY2) and secondary interlock
switch remain closed with the oven door open and when
the monitor switch closes.
2. If the wire harness or electrical components are shortcircuited, this monitor fuse blows to prevent an electric
shock or fire hazard.
NOTE: This is fuse. It does not reset.
Functions:
1. When the door is opened, the monitor switch contact close
(to the ON condition) due to their being normally closed. At
this time the primary interlock relay (RY2) and secondary
interlock switch are in the OFF condition (contacts open)
due to their being normally open contact switches.
2. As the door goes to a closed position, the monitor switch
contacts are first opened and then the door sensing switch
and the secondary interlock switch contacts close. (On
opening the door, each of these switches operate inversely.)
9
DMT2420B
DMT2420R
DMT2420S
TROUBLESHOOTING GUIDE
Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is connected.
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many
of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which
will be found in the "Test Procedure "section.
IMPORTANT: If the oven becomes inoperative because of a blown C/T fuse, check the monitor switch, relay (RY1) primary
interlock relay (RY2), door sensing switch and secondary interlock switch before replacing the C/T fuse. If the
C/T fuse is replaced, the monitor switch must also be replaced. Use part FFS-BA019/KIT as an assembly.
IMPORTANT: Whenever troubleshooting is performed with the power supply cord disconnected. It may in, some cases, be
necessary to connect the power supply cord after the outer case has been removed, in this event:
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
When the testing is completed
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is installed.
7. Run the oven and check all functions.
10
DMT2420B
DMT2420R
DMT2420S
CK = Check / RE = Replace
POSSIBLE CAUSE
AND
DEFECTIVE PARTS
CONDITION
PROBLEM
RE RE A B C D E E F F G H RE RE CK I CK CK CK J K L M N
SHORT IN POWER CORD
SHORT OR OPENED WIRING
MAGNETRON
POWER TRANSFORMER
H.V. RECTIFIER ASSEMBLY
HIGH VOLTAGE CAPACITOR
CAVITY TEMPERATURE FUSE
C/T FUSE
SECONDARY INTERLOCK SYSTEM
PRIMARY INTERLOCK RELAY
MONITOR SWITCH
C/T FUSE
OVEN LAMP OR SOCKET
COOLING FAN MOTOR
TURNTABLE MOTOR
TOUCH CONTROL PANEL
WRONG OPERATION
LOW VOLTAGE
DIRTY OVEN CAVITY
KEY UNIT
RELAY (RY1)
DEFROST CENTER
FOIL PATTERN ON PWB.
AH SENSOR
TEST PROCEDURE
Home fuse or circuit breaker blows when
power cord is plugged into wall receptacle.
Monitor fuse blows when power cord is
plugged into wall receptacle.
OFF
CONDITION
COOKING
CONDITION
SENSOR
COOKING
CONDITION
A
Any letters or indicators do not appear in
display when power cord is first plugged
into wall outlet.
Display does not operate properly when
STOP/CLEAR key is touched. (Buzzer
should sound and ":" or time of day
should appear in display.)
Oven lamp does not light when door is
opened.
Oven lamp does not go out when door is
closed.
Oven lamp lights but fan motor and
turntable motor do not operate.
Oven does not go into cook cycle when
START pad is touched
Oven seems to be operating but little or
no heat is produced in oven load. (Food
incompletely cooked or not cooked at all
at end of cook cycle.)
Oven goes into a cook cycle but
extremely uneven heating is produced in
oven load (food).
Oven does not cook properly when
programmed for P-50/ 50 PERCENT
mode. (Operates properly on P-HI/ 100
PERCENT mode.)
Oven goes into Defrost Center but food
is not defrosted well.
AH sensor does not end during Sensor
cooking condition. (Oven does not shut
off after a cup of water is boiling by
sensor cooking.)
Oven stops at 16 sec. after starting.
MAGNETRON ASSEMBLY TEST
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check across the
magnetron filament leads should indicate less than 1 ohm.
5. To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads and chassis
ground. This test should indicate an infinite resistance. If there is little or no resistance the magnetron is grounded
and must be replaced.
11
DMT2420B
DMT2420R
DMT2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
6.
7.
8.
9.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
MICROWAVE OUTPUT POWER
The following test procedure should be carried out with the microwave oven in a fully assembled condition
(outer case fitted).
HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD BE
OBSERVED.
Power output of the magnetron can be measured by performing a water temperature rise test. This test
should only be used if above tests do not indicate a faulty magnetron and there is no defect in the following
components or wiring: silicon rectifier, high voltage capacitor and power transformer. This test will require
a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple type
temperature tester. For accurate results, the following procedure must be followed carefully:
1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water with
a thermometer or thermocouple temperature tester. Stir the thermometer or thermocouple through the
water until the temperature stabilizes. Record the temperature of the water.
2. Place the cup of water in the oven. Operate oven at 100 PERCENT POWER/ P-HI selecting more than
60 seconds cook time. Allow the water to heat for 60 seconds, measuring with a stop watch, second
hand of a watch or the digital read-out countdown.
3. Remove the cup from the oven and again measure the temperature, making sure to stir the thermometer
or thermocouple through the water until the maximum temperature is recorded.
4. Subtract the cold water temperature from the hot water temperature. The normal result should be 33
to 62½F(18.6 to 34.5½C) rise in temperature. If the water temperatures are accurately measured and
tested for the required time period the test results will indicate if the magnetron tube has low power output
(low rise in water temperature) which would extend cooking time or high power output (high rise in water
temperature) which would reduce cooking time. Because cooking time can be adjusted to compensate
for power output, the magnetron tube assembly should be replaced only if the water temperature rise
test indicates a power output well beyond the normal limits. The test is only accurate if the power supply
line voltage is 120 volts and the oven cavity is clean.
B
POWER TRANSFORMER TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the primary input terminals and measure the resistance of the transformer with an
ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of
the primary coil should be less than 1 ohm and the resistance of the high voltage coil should be
approximately 90 ohms; the resistance of the filament coil should be less than 1 ohm.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO
MEASURE THE FILAMENT AND HIGH VOLTAGE.)
12
TEST PROCEDURES
PROCEDURE
LETTER
C
DMT2420B
DMT2420R
DMT2420S
COMPONENT TEST
HIGH VOLTAGE RECTIFIER TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance across
the terminals and observe, reverse the leads to the rectifier terminals and observe meter reading. If a
short is indicated in both directions, or if an infinite resistance is read in both directions, the rectifier
is probably defective and should be replaced.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.
D
HIGH VOLTAGE CAPACITOR TEST
1.
2.
3.
4.
5.
6.
7.
8.
E
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads and
check for short or open between the terminals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate continuity
for a short time and should indicate an open circuit once the capacitor is charged. If the above is not
the case, check the capacitor with an ohmmeter to see if it is shorted between either of the terminals
and case. If it is shorted, replace the capacitor.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
CAVITY TEMPERATURE FUSE TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
A continuity check across the cavity temperature fuse terminals should indicate a closed circuit unless
the temperature of the cavity temperature fuse reaches approximately 302OF(150OC). An open cavity
temperature fuse indicates overheating of the oven, exchange the cavity temperature fuse and check
inside of oven cavity and for improper setting of cooking time or operation of control unit. Check for
restricted air flow through the vent holes of the oven cavity, especially the cooling fan and air guide.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
C/T FUSE TEST
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. A continuity check across the C/T fuse terminals should indicate a closed circuit unless the temperature
of the C/T fuse reaches approximately 302OF(150OC). An open C/T fuse indicates overheating of the
magnetron. Check for restricted air flow to the magnetron, especially the cooling fan air guide.
CAUTION: IF THE TEMPERATURE FUSE INDICATES AN OPEN CIRCUIT AT ROOM
TEMPERATURE, REPLACE TEMPERATURE FUSE.
5. If the C/T fuse is blown when the door is opened, check the primary interlock relay, secondary
interlock switch and monitor switch according to the "TEST PROCEDURE" for those switches before
replacing the blown monitor fuse.
13
DMT2420B
DMT2420R
DMT2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
CAUTION: BEFORE REPLACING A BLOWN C/T FUSE, TEST THE PRIMARY INTERLOCK RELAY,
SECONDARY INTERLOCK SWITCH, DOOR SENSING SWITCH AND MONITOR SWITCH
FOR PROPER OPERATION.
If the C/T fuse is blown by improper switch operation, the C/T fuse and monitor switch must be replaced
with "C/T fuse and monitor switch assembly" part number FFS-BA019/KIT, even if the monitor switch
operates normally. The C/T fuse and monitor switch assembly is comprised of a 20 ampere fuse and
switch.
6. Reconnect all leads removed from components during testing.
7. Reinstall the outer case (cabinet).
8. Reconnect the power supply cord after the outer case is installed.
9. Run the oven and check all functions.
F
SECONDARY INTERLOCK SYSTEM TEST
DOOR SENSING SWITCH
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the door sensing switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the cooling fan,
turntable and oven light will be activated by RY1.
PRIMARY INTERLOCK RELAY (RY2)
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect two (2) wire leads from the male tab terminals of the Secondary Interlock Relay. Check the
state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay contacts
are closed, replace the circuit board entirely or the relay itself.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
14
DMT2420B
DMT2420R
DMT2420S
TEST PROCEDURES
PROCEDURE
LETTER
G
COMPONENT TEST
MONITOR SWITCH TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Before performing this test, make sure that the secondary interlock switch and the primary interlock
relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire lead
from the monitor switch (COM) terminal. Check the monitor switch operation by using the ohmmeter
as follows. When the door is open, the meter should indicate a closed circuit. When the monitor switch
actuator is pushed by a screw driver through the lower latch hole on the front plate of the oven cavity
with the door opened (in this condition the plunger of the monitor switch is pushed in), the meter should
indicate an open circuit. If improper operation is indicated, the switch may be defective. After testing
the monitor switch, reconnect the wire lead to the monitor switch (COM) terminal and check the
continuity of the monitor circuit.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
Red
White/ White
Screw Driver
Ohmmeter
Secondary
Interlock Switch
H
Monitor Switch
TOUCH CONTROL PANEL ASSEMBLY TEST
The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore,
unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter and
ohmmeter. In this service manual, the touch control panel assembly is divided into two units, Control Unit
and Key Unit, and also the Control Unit is divided into two units, LSI Unit and Power Unit, and
troubleshooting by unit replacement is described according to the symptoms indicated.
Before testing,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using insulation tape.
1. Key Unit.
NOTE :
1) Check Key unit ribbon connection before replacement.
2) Re-install the outer case (cabinet).
3) Reconnect the power supply cord after the outer case is installed.
4) Run the oven and check all functions.
The following symptoms indicate a defective key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
If the Key unit is defective.
15
DMT2420B
DMT2420R
DMT2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Replace the Key unit.
5) Reconnect all leads removed from components during testing.
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.
2. Control Unit
The following symptoms indicate a defective control unit. Before replacing the control unit, perform the
Key unit test (Procedure J) to determine if control unit is faulty.
2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) The figure of all digits flicker.
2-3 Other possible problems caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
When testing is completed,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Reconnect all leads removed from components during testing.
5) Re-install the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions..
I
KEY UNIT TEST
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable
is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing switch
(stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and
make sure the door sensing switch is closed (either close the door or short the door sensing switch
connecter). Use the Key unit matrix indicated on the control panel schematic and place a jumper wire
between the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control
unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does
not respond, it is faulty and must be replaced. If a specific pad does not respond, the above method
may be used (after clearing the control unit) to determine if the control unit or key pad is at fault.
5. Reconnect all leads removed from components during testing.
16
DMT2420B
DMT2420R
DMT2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
6. Re-install the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
G1
G3
MICROWAVE
RECIPES &
INSTRUCTIONS
G5
SETUP
DEFROST
G6
PASTA
GRAINS
BEVERAGES
G13
G12
G11
BAKED
POTATOES
POULTRY
G15
J
G2
G14
G7
G8
G9
G10
G14
STOP
CLEAR
VEGETABLES
FROZEN
FOOD
START
REHEAT
POPCORN
EASY
MINUTE
FISH
SEAFOOD
MEATS
TOUCH SCREEN
KEY UNIT
RELAY TEST
2.
3.
4.
5.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the leads to the primary of the power transformer.
Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape.
6. After that procedure, re-connect the power supply cord.
7. Remove the outer case and check voltage between Pin No. 1 of the 2 pin connector (A) and the common
terminal of the relay RY1 on the control unit with an A.C. voltmeter.
The meter should indicate 120 volts, if not check oven circuit.
RY1 and RY2 Relay Test
These relays are operated by D.C. voltage
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.
DC. voltage indicated .......................... Defective relay.
DC. voltage not indicated .................... Check diode which is connected to the relay coil. If diode
is good, control unit is defective.
RELAY SYMBOL
OPERATIONAL VOLTAGE
CONNECTED COMPONENTS
RY1
Approx. 24.0V D.C.
Oven lamp / Turntable motor / Cooling fan motor
RY2
Approx. 23.0V D.C.
Power transformer
8.
Disconnect the power supply cord, and then remove outer case.
9.
Open the door and block it open.
10.Discharge high voltage capacitor.
11.Reconnect all leads removed from components during testing.
12.Re-install the outer case (cabinet).
13.Reconnect the power supply cord after the outer case is installed.
14.Run the oven and check all functions.
K
COMPU DEFROST TEST
WARNING : The oven should be fully assembled before following procedure.
(1) Place one cup of water in the center of the turntable tray in the oven cavity.
(2) Close the door, touch the Defrost pad and select 6 Choices. Then select Steaks/Chops/Fish.
(Now, weight 0.5lb is set.) And then touch the start pad.
(3) The oven is in Defrost cooking condition.
(4) The oven will operate as follows
17
DMT2420B
DMT2420R
DMT2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
WEIGHT
0.5lb
1ST STAGE
LEVEL
TIME
70%
30sec.
2ND STAGE
LEVEL
TIME
40%
15sec.
(5) If improper operation is indicated, the control unit is probably defective and should be checked.
L
FOIL PATTERN ON THE PRINTED WIRING BOARD TEST
To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary on the
PWB, this foil pattern acts as a fuse.
1. Foil pattern check and repairs.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Follow the troubleshooting guide given below for repair.
STEPS
OCCURRENCE
CAUSE OR CORRECTION
1
Only pattern at "a" is broken.
*Insert jumper wire J1 and solder.
2
Pattern at "a" and "b" are broken.
*Insert the coil RCILF2003YAZZ between "c" and "d".
RY1
5) Make a visual inspection of the varistor.
Check for burn damage and examine the
transformer with a tester for the presence
of layer short-circuit (check the primary
coil resistance which is approximately
210ý ± 15%). If any abnormal condition is
detected, replace the defective parts.
a
c
6)
7)
8)
9)
(J1)
b
VRS1
d
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
2. Follow the troubleshooting guide given below, if indicator does not light up after above check and repairs
are finished.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
6) After that procedure, reconnect the power supply cord.
7) Follow the troubleshooting guide given below for repair.
STEPS
OCCURRENCE
CAUSE OR CORRECTION
1
The rated AC voltage is not present between
Pin No. 1 of the 2-pin connector (A) and the Check supply voltage and oven power cord.
common terminal of the relay RY1.
2
The rated AC voltage is present at primary
side of low voltage transformer.
Low voltage transformer or secondary circuit defective.
Check and repair.
8) Disconnect the power supply cord, and then remove outer case.
9) Open the door and block it open.
18
DMT2420B
DMT2420R
DMT2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
10) Discharge high voltage capacitor.
11) Reconnect all leads removed from components during testing.
12) Re-install the outer case (cabinet).
13) Reconnect the power supply cord after the outer case is installed.
14) Run the oven and check all functions.
M
AH SENSOR TEST
Checking the initial sensor cooking condition
WARNING : The oven should be fully assembled before following procedure.
(1) The oven should be plugged in at least two minutes before sensor cooking.
(2) Room temperature should not exceed 95½F (35½C).
(3) The unit should not be installed in any area where heat and steam are generated. The unit should not
be installed, for example, next to a conventional surface unit. Refer to the “INSTALLATION
INSTRUCTIONS” of the operation manual.
(4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To permit
adequate ventilation, be sure to install so as not to block these vents. There should be some space
for air circulation.
(5) Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any moisture
with a dry cloth or paper towel.
(6) The Sensor works with food at normal storage temperature. For example, chicken pieces would be at
refrigerator temperature and canned soup at room temperature.
(7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The sensor
will detect the vapor given of by the spray and turn off before food is properly cooked.
(8) If the sensor has not detected the vapor of the food, ERROR will appear and the oven will shut off.
Water load cooking test
WARNING : The oven should be fully assembled before following procedure.
Make sure the oven has been plugged in at least two minutes before checking sensor cook operation. The
cabinet should be installed and screws tightened.
(1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
(2) Place the container on the center of tray in the oven cavity.
(3) Close the door.
(4) Touch the Timer/Clock pad once, the Power Level pad twice, the Start pad once and the number pad
1 once. Now, the oven is in the sensor cooking condition and "TEST", “SENSOR” and "COOK" will
appear in the display.
(5) The oven will operate for the first 16 seconds, without generating microwave energy.
NOTE: ERROR will appear if the door is opened or STOP/CLEAR pad is touched during first stage of sensor
cooking.
(6) After approximately 16 seconds, microwave energy is produced.
If ERROR is displayed, replace the AH sensor or check the control unit, refer to explanation below.
If the oven stops after 5 minutes and ERROR is displayed, check the parts except for the AH sensor.
TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement sensor.
(1) Disconnect the power supply cord, and then remove outer case.
(2) Open the door and block it open.
(3) Discharge high voltage capacitor.
(4) Remove the AH sensor.
(5) Install the new AH sensor.
(6) Reconnect all leads removed from components during testing.
(7) Re-install the outer case (cabinet).
(8) Reconnect the power supply cord after the outer case is installed.
(9) Reconnect the oven to the power supply and check the sensor cook operation as follows:
9-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
9-2. Place the container on the center of tray in the oven cavity.
19
DMT2420B
DMT2420R
DMT2420S
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
9-3. Close the door.
9-4. Touch the Timer/Clock pad once, the Power Level pad twice, the Start pad once and the number
pad 1 once.
9-5. The control panel is in automatic Sensor operation.
9-6. And then the oven will turn off automatically, and the time for detecting moisture will be displayed.
If new sensor dose not operate properly, the problem is with the control unit, and refer to explanation below.
CHECKING CONTROL UNIT
(1) Disconnect the power supply cord, and then remove outer case.
(2) Open the door and block it open.
(3) Discharge high voltage capacitor.
(4) Disconnect the sensor connector that is mounted to control panel.
(5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel.
(6) Disconnect the leads to the primary of the power transformer.
(7) Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape.
(8) After that procedure, re-connect the power supply cord.
(9) Check the sensor cook operation proceed as follows:
9-1. Touch the Timer/Clock pad once, the Power Level pad twice, the Start pad once and the number
pad 1 once.
9-2. The control panel is in the sensor cooking operation.
9-3. After approximately 25 seconds, push plunger of select switch for more than 3 seconds. This
condition is same as judgement by AH sensor.
9-4. After approximately 3 seconds, the oven will turn off automatically, and the display shows “ X
X . X X “ which is the time for detecting moisture.
If the above is not the case, the control unit is probably defective.
If the above is proper, the AH sensor is probably defective.
(10) Disconnect the power supply cord, and then remove outer case.
(11) Open the door and block it open.
(12) Discharge high voltage capacitor.
(13) Disconnect the dummy resistor circuit from the sensor connector of control panel.
(14) Carry out necessary repair.
(15) Reconnect all leads removed from components during testing and repairing.
(16) Re-install the outer case (cabinet).
(17) Reconnect the power supply cord after the outer case is installed. Run the oven and check all functions.
(18) Carry out "Water load cooking test" again and ensure that the oven works properly.
R1,R2 : 22 ohm ± 1% 1/2W
R3 : 10k ohm ± 5% 1/4W
R4 : 1M ohm ± 5% 1/4W
Plunger
Sensor Dummy Resistor Circuit
F-1
NC
NO
To connector (F)
on Control Unit.
1
2
3
F-2
F-3
CONNECTOR
20
COM
COM
R1
R2
R3
R4
NO
NC
DMT2420B
DMT2420R
DMT2420S
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
unit from the AC line voltage.
In addition, the synchronizing signal is available in
order to compose a basic standard time in the clock
circuit.
The touch control section consists of the following units.
(1) Key Unit
(2) Control Unit (The Control Unit consists of Power Unit and
LSI Unit).
The principal functions of these units and the signals communicated among them are explained below.
Symbol
Voltage
VC
+5V
Application
LSI(IC1)
9) Relay Circuit
A circuit to drive the magnetron, fan motor, turntable
motor and light the oven lamp.
Key Unit
The key unit is composed of a matrix, signals generated in the
LSI are sent to the key unit through P93, P94, P95 and P40.
When a key pad is touched, a signal is completed through the
key unit and passed back to the LSI through PB1, PB2, PB3,
PB4, PB5 and AN1 to perform the function that was requested.
10) Buzzer Circuit
The buzzer is responsive to signals from the LSI to emit
audible sounds (key touch sound and completion sound).
11) Synchronizing Signal Circuit
The power source synchronizing signal is available in
order to compose a basic standard time in the clock
circuit.
It accompanies a very small error because it works
on commercial frequency.
Control Unit
Control unit consists of LSI, IC, ACL circuit, indicator circuit,
power source circuit, relay circuit, buzzer circuit, synchronizing signal circuit, key unit circuit, touch screen circuit,
absolute humidity sensor circuit and back light circuit.
12) Door Sensing Switch
A switch to “tell” the LSI if the door is open or closed.
1) IC1 (LSI)
This is a microcomputer, responsible for controlling the
entire control unit.
13) Back Light Circuit
A circuit to drive the back light (Light emitting diodes
LED1 and LED2).
2) IC2
This is a read only memory IC, responsible for giving IC1
the all programmes.
14) Absolute Humidity Sensor Circuit
This circuit detects moisture of the cooking food to allow
its automatic cooking.
3) IC3
This is an amplifier IC. This IC controls the contrast of
LCD and amplify the sensor signal.
15) Touch Screen
The touch screen is composed of a matrix, signal
generated in the LSI are sent to the key unit through P41,
P42, P43 and P44. When a key is touched, a signal is
completed through the touch screen and passed back to
the LSI through PB1, PB2, PB3, PB4 and PB5 to
perform the function that was requested.
4) IC4
This is a memory IC. This memorizes the contrast of LCD.
5) IC5
This IC drives the LCD.
6) ACL
This circuit generates a signal which resets the LSI (IC1)
to the initial state when power is supplied.
7) Indicator Circuit
This circuit consists of 100 x 160 dots using a Liquid
Crystal Display. The Liquid Crystal Display (LCD) is
drived by IC5.
8) Power Source Circuit
This circuit generates voltages necessary in the control
21
DMT2420B
DMT2420R
DMT2420S
LSI(IXA029DR)
The I/O signal of the LSI(IXA029DR) is detailed in the following table.
Pin No.
Signal
I/O
Description
1
TIOCA2
OUT
Terminal not used.
2
A20
OUT
Terminal not used.
3
Vcc
IN
4
TMO0
OUT
5
PB1
IN
Signal coming from touch key.
When either G11 line on key matrix is touched, a corresponding signal out of P93, P94,
P95, P40, P41, P42, P43 and P44 will be input into PB1. When no key is touched, the
signal is held at "H" level.
6
PB2
IN
Signal similar to PB1.
When either G12 line on key matrix is touched, a corresponding signal will be input into
PB2.
7
PB3
IN
Signal similar to PB1.
When either G13 line on key matrix is touched, a corresponding signal will be input into
PB3.
8
PB4
IN
Signal similar to PB1.
When either G6 line on key matrix is touched, a corresponding signal will be input into PB4.
9
PB5
IN
Signal similar to PB1.
When either G5 line on key matrix is touched, a corresponding signal will be input into PB5.
10-11
PB6-PB7
OUT
Terminal not used.
12
RESO
OUT
Terminal not used.
13
Vss
IN
14
TxD0
OUT
Data signal is output to a memory IC (IC4).
15
P91
OUT
Clock signal is output to a memory IC (IC4).
16
RxD0
OUT
Terminal not used.
17
P93
OUT
Key strobe signal.
Signal applied to key unit section. A pulse signal is input to PB1-PB5 terminal while one
of G1 line keys on key matrix is touched.
18
P94
OUT
Key strobe signal.
Signal applied to key unit section. A pulse signal is input to PB1-PB5 and AN1 terminal
while one of G2 line keys on key matrix is touched.
19
P95
OUT
Key strobe signal.
Signal applied to key unit section. A pulse signal is input to PB1-PB5 terminal while one
of G3 line keys on key matrix is touched.
20
P40
OUT
Key strobe signal.
Signal applied to key unit section. A pulse signal is input to PB1-PB5 terminal while one
of G14 line keys on key matrix is touched.
21
P41
OUT
Key strobe signal.
Signal applied to touch screen section. A pulse signal is input to PB1-PB5 terminal while
one of G7 line keys on key matrix is touched.
22
P42
OUT
Key strobe signal.
Signal applied to touch screen section. A pulse signal is input to PB1-PB5 terminal while
one of G8 line keys on key matrix is touched.
23
P43
OUT
Key strobe signal.
Signal applied to touch screen section. A pulse signal is input to PB1-PB5 terminal while
one of G9 line keys on key matrix is touched.
Power source voltage : +5.0V.
The power source voltage to drive LSI is input to Vcc terminal. Connected to Vcc.
Signal to sound buzzer.
A: key touch sound (short beep). B: Completion sound (melody or long beep).
Power source voltage: GND(0V).
The power source voltage to drive LSI is input to Vss terminal.
22
DMT2420B
DMT2420R
DMT2420S
Pin No.
24
Signal
Vss
I/O
IN
25
P44
OUT
26
P45
OUT
Description
Power source voltage : GND(0V).
The power source voltage to drive LSI is input to VSS terminal.
Key strobe signal.
Signal applied to touch screen section. A pulse signal is input to PB1-PB5 terminal while
one of G10 line keys on key matrix is touched.
Oven lamp, fan motor and turntable motor driving signal
16.7 msec.
To turn on and off shut off relay (RY1). The
square waveform voltage is delivered to the
RY1 driving circuit and RY2 control circuit.
H : +5V
L : GND
During cooking
27
P46
OUT
Magnetron high-voltage circuit driving signal.
ON
H : +5V
100
To turn on and off the cook relay (RY2). The
PERCENT
signals holds "H" level during microwave cookOFF
L : GND
ing and "L" level while not cooking. In other
ON
H : +5V
cooking modes (variable cooking) the signal
70
24 sec.
turns to "L" level and "H" level in repetition
PERCENT
8 sec. OFF
L : GND
according to the power level.
(ON and OFF times for other power level.)
28
P47
OUT
Terminal not used.
29-36
D8-D15
OUT
Data signal is output to IC2 and IC5.
37
Vcc
IN
38-45
A0-A7
OUT
46
Vss
IN
47-58
A8-A19
OUT
59
Vss
IN
Power source voltage : GND (0V).
The power source voltage to drive LSI is input to Vss terminal.
60
WATT
IN
Connected to VCC.
61
P61
OUT
Envelope signal to sound buzzer.
A: key touch sound (short beep). B: Completion sound (melody or long beep).
62
P62
OUT
Reset signal is output to IC5.
63
P67
OUT
Terminal not used.
64
STBY
IN
Connected to VCC.
65
RES
IN
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily set
"L" level the moment power is applied, at this time the LSI is reset. Thereafter set at "H"
level.
66
NMI
IN
Connected to GND.
67
Vss
IN
Power source voltage : GND (0V).
The power source voltage to drive LSI is input to Vss terminal.
68
EXTAL
OUT
69
XTAL
IN
Internal clock oscillation frequency control input setting.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit with
respect to XTAL.
70
Vcc
IN
Power source voltage : +5V.
The power source voltage to drive LSI is input to Vcc terminal. Connected to VCC.
71
AS
OUT
Terminal not used.
72
RD
OUT
Read strobe signal is output to RD terminal of IC5.
Power source voltage : +5V.
The power source voltage to drive LSI is input to Vcc terminal. Connected to VCC.
Address signal is output to IC2 and IC5.
Power source voltage : GND (0V).
The power source voltage to drive LSI is input to Vss terminal.
Address signal is output to IC2 and IC5.
Internal clock oscillation output.
Output to control oscillation input to EXTAL.
23
DMT2420B
DMT2420R
DMT2420S
Pin No.
75-76
Signal
MD0-MD1
I/O
IN
Description
Connected to VCC.
77
MD2
IN
Connected to GND.
78
Avcc
IN
A/D converter power source voltage : +5V.
The power source voltage to drive the A/D converter. Connected to VCC.
79
Vref
IN
A/D converter power source voltage : +5V.
The power source voltage to drive the A/D converter. Connected to VCC.
80
AN0
IN
Terminal to judge whether the model has the sensor cooking function or not.
By using the A/D converter contained in the LSI, DC voltage in accordance with the Model
in operation is applied to judge whether the model has the sensor cooking function or not.
81
AN1
IN
Input terminal to judge the model.
The signal out of P94 will be input into AN1 through G15 line on key matrix. The LSI will
judge the model by this signal.
82
AN2
IN
Terminal to change cooking input according to the model.
By using the A/D converter contained in the LSI, DC voltage in accordance with the Model
in operation is applied to set up its cooking constant.
83
AN3
IN
Connected to VCC.
84
AN4
IN
To input signal which communicates the door open/close information to LSI.
Door close "H" level signal (+5V). Door open "L" level signal (GND).
85
AN5
IN
Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is an
analog input terminal from the AH sensor circuit, and connected to the A/D converter built
into the LSI.
86
AN6
IN
AH sensor input.
This input is an analog input terminal from the AH sensor circuit, and connected to the A/
D converter built into the LSI.
87
DA1
OUT
88
Avss
IN
A/D converter power source voltage : GND(0V).
The power source voltage to drive the A/D converter. Connected to GND.
89
IRQ0
IN
Signal synchronized with commercial power source frequency.
This is the basic timing for time processing of LSI.
The signal for the power source to drive the LCD is output to IC3.
H : +5V
L : GND
16.7 msec.
90-91
P81-P82
OUT
Terminal not used.
92
CS1
OUT
Chip select signal is output to CS terminal of IC5.
93
CS0
OUT
Chip select signal is output to CE terminal of IC2.
94
Vss
IN
95-99
PA0-PA4
OUT
Used for initial balancing of the bridge circuit (absol ute humidity sensor).
100
PA5
OUT
Clock signal is output to IC5.
Power source voltage : GND (0V).
The power source voltage to drive the LSI is input to Vss terminal.
24
DMT2420B
DMT2420R
DMT2420S
ABSOLUTE HUMIDITY SENSOR CIRCUIT
With this voltage given, the switches SW1 to SW5 in the
LSI are turned on in such a way as to change the
resistance values in parallel with R98 ~ R102. Changing
the resistance values results in that there is the same
potential at both F-3 terminal of the absolute humidity
sensor and AIN4 terminal of the LSI. The voltage of AIN5
terminal will indicate about -2.5V. This initial balancing is
set up about 16 seconds after the unit is put in the Sensor
Cooking mode. As the sensor cooking proceeds, the
food is heated to generate moisture by which the
resistance balance of the bridge circuit is deviated to
increase the voltage available at AIN5 terminal of the
LSI.
Then the LSI observes that voltage at AIN5 terminal and
compares it with its initial value, and when the comparison
rate reaches the preset value (fixed for each menu to be
cooked), the LSI causes the unit to stop sensor cooking;
thereafter, the unit goes in the next operation
automatically.
When the LSI starts to detect the initial voltage at AIN5
terminal 16 seconds after the unit has been put in the
Sensor Cooking mode, if it is not possible to balance the
bridge circuit due to disconnection of the absolute humidity
sensor, ERROR will appear on the display and the
cooking is stopped.
(1) Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed in
the closed vessel filled with dry air while another in the
open vessel. Each sensor is provided with the protective
cover made of metal mesh to be protected from the
external airflow.
ventilation opening for sensing
(2) Operational Principle of Absolute Humidity Sensor
The figure below shows the basic structure of an absolute
humidity sensor. A bridge circuit is formed by two
thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
Each thermistor is supplied with a current to keep it
heated at about 150½C (302½F), the resultant heat is
dissipated in the air and if the two thermistors are placed
in different humidity conditions they show different
degrees of heat conductivity leading to a potential
difference between them causing an output voltage from
the bridge circuit, the intensity of which is increased as
the absolute humidity of the air increases. Since the
output is very minute, it is amplified by the operational
amplifier.
300k
25
R100
150k
24
R101
75k
23
R102
37.4k
22
C. Thermistor in
closed vessel
S. Thermistor in
open vessel
R97
50
Absolute humidity (g/m 2 )
S
F-2
R90
(3) Detector Circuit of Absolute Humidity Sensor Circuit
This detector circuit is used to detect the output voltage
of the absolute humidity circuit to allow the LSI to control
sensor cooking of the unit. When the unit is set in the
sensor cooking mode, 16 seconds clearing cycle occurs
than the detector circuit starts to function and the LSI
observes the initial voltage available at its AIN5 terminal.
R91
3.32k R92
1.8k
VA : -15V
25
8 7 6 5
1 2 3 4
R94
R95
10k
47k
R93
360k
D91
VA : -15V
VC : -5V
IC2
P21
P22
P23
P24
D90
SW2
SW3
SW4
SW5
AIN4
0.01uF
F-1
C
R96
F-3
3.57k
0.01uF
47k
0.015uF
Absolute humidity vs,
output voltage characteristic
C93
S : Thermistor
open vessel
C : Thermistor
closed vessel
R99
SW1
P20
LSI
(IC1)
C92
R3
R2
26
C91
S
R1
620k
R98
Output voltage
C
Operational
amplifier
Output
voltage
+
1) Absolute humidity sensor circuit
0.1
uF
Sensing part
(Closed vessel)
C90
Thermistors
Sensing part
(Open vessel)
49
AIN5
DMT2420B
DMT2420R
DMT2420S
TOUCH CONTROL PANEL SERVICING
4) Re-install the outer case (cabinet).
5) Re-connect the power supply cord after the outer
case is installed.
6) Run the oven and check all functions.
A. On some models, the power supply cord between the
touch control panel and the oven itself is so short that the
two can’t be separated. For those models, check and
repair all the controls (sensor-related ones included) of
the touch control panel while keeping it connected to the
oven.
B. On some models, the power supply cord between the
touch control panel and the oven proper is long enough
that they may be separated from each other. For those
models, it is possible to check and repair the controls of
the touch control panel while keeping it apart from the
oven proper; in this case you must short both ends of the
door sensing switch (on PWB) of the touch control panel
with a jumper, which activates an operational state that
is equivalent to the oven door being closed. As for the
sensor-related controls of the touch control panel,
checking them is possible if dummy resistor(s) with
resistance equal to that of the controls are used.
(2) Servicing the touch control panel with power supply
from an external power source:
Disconnect the touch control panel completely from the
oven proper, and short both ends of the door sensing
switch (on PWB) of the touch control panel, which
activates an operational state that is equivalent to the
oven door being closed. Connect an external power
source to the power input terminal of the touch control
panel, then it is possible to check and repair the controls
of the touch control panel it is also possible to check the
sensor-related controls of the touch control panel by
using the dummy resistor(s).
1. Precautions for Handling Electronic Components
This unit uses CMOS LSI in the integral part of the
circuits. When handling these parts, the following
precautions should be strictly followed. CMOS LSI have
extremely high impedance at its input and output
terminals. For this reason, it is easily influenced by the
surrounding high voltage power source, static electricity
charge in clothes, etc. and sometimes it is not fully
protected by the built-in protection circuit.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them in
aluminium foil. Also wrap all PW boards containing them
in aluminium foil.
2) When soldering, ground the technician as shown in the
figure and use grounded soldering iron and work table.
approx. 1M ohm
2. Shapes of Electronic Components
3. Servicing of Touch Control Panel
We describe the procedures to permit servicing of the
touch control panel of the microwave oven and the
precautions you must take when doing so. To perform
the servicing, power to the touch control panel is available
either from the power line of the oven itself or from an
external power source.
(1) Servicing the touch control panel with power supply
of the oven:
CAUTION:
THE HIGH VOLTAGE TRANSFORMER OF THE
MICROWAVE OVEN IS STILL LIVE DURING
SERVICING AND PRESENTS A HAZARD.
Therefore, before checking the performance of the touch
control panel,
1) Disconnect the power supply cord, and then remove
outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power
transformer.
5) Ensure that these leads remain isolated from other
components and oven chassis by using insulation
tape.
6) After that procedure, re-connect the power supply
cord.
After checking the performance of the touch control
panel,
1) Disconnect the power supply cord.
2) Open the door and block it open.
3) Re-connect the leads to the primary of the power
transformer.
4. Servicing Tools
Tools required to service the touch control panel
assembly.
1) Soldering iron: 30W
(It is recommended to use a soldering iron with a
grounding terminal.)
2) Oscilloscope: Single beam, frequency range: DC-10MHz
type or more advanced model.
3) Others: Hand tools
5. Other Precautions
1) Before turning on the power source of the control unit,
remove the aluminium foil applied for preventing static
electricity.
2) Connect the connectors of the key unit to the control unit
being sure that the lead wires are not twisted.
3) After aluminium foil is removed, be careful that abnormal
voltage due to static electricity etc. is not applied to the
input or output terminals.
4) Attach connectors, electrolytic capacitors, etc. to PWB,
making sure that all connections are tight.
5) Be sure to use specified components where high precision
is required.
26
DMT2420B
DMT2420R
DMT2420S
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
WARNING AGAINST HIGH VOLTAGE:
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may
result in severe, possibly fatal, electric shock.
(Example)
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
WARNING:
Avoid possible exposure to microwave energy. Please follow the instructions below before
operating the oven.
1. Disconnect the power supply cord.
2. Make sure that a definite” click” can be heard when the
microwave oven door is unlatched. (Hold the door in a
closed position with one hand, then push the door open
button with the other, this causes the latch leads to rise,
it is then possible to hear a “click’ as the door switches
operate.)
3. Visually check the door and cavity face plate for damage
(dents, cracks, signs of arcing etc.).
1.
2.
3.
4.
5.
6.
Door does not close firmly.
Door hinge, support or latch hook is damaged.
The door gasket or seal is damaged.
The door is bent or warped.
There are defective parts in the door interlock system.
There are defective parts in the microwave generating
and transmission assembly.
7. There is visible damage to the oven.
Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
WARNING FOR WIRING
To prevent an electric shock, take the following precautions.
1. Before wiring,
1) Disconnect the power supply cord.
2) Open the door block it open.
3) Discharge the high voltage capacitor and wait for 60
seconds.
2. Don’t let the wire leads touch to the following parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, High voltage transformer
and Oven cavity.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector until its pin is locked
and make sure that the wire leads do not come off even
if the wire leads are pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS’, when carrying out any of
the following removal procedures:
OUTER CASE REMOVAL
To remove the outer case, proceed as follows.
1. Disconnect the power supply cord.
2. Open the oven door and block it open.
3. Remove the two (2) screws from the lower portion of the
rear cabinet using a T20H Torx type or GTXH20-100
screw driver.
4. Remove the remaining two (2) screws from rear and four
(4) screws along the right side of outer case.
5. Slide the entire outer case back out about 1 inch (3 cm)
to free it from retaining clips on the cavity face plate.
6. Lift entire outer case from the unit.
27
DMT2420B
DMT2420R
DMT2420S
CAUTION: 1. DISCONNECT OVEN FROM POWER SUP
PLY BEFORE REMOVING OUTER CASE.
2. DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE TOUCHING ANY OVEN
COMPONENTS OR WIRING.
NOTE: When replacing the outer case, the 2 special
Torx screws must be reinstalled in the same
locations.
Special screw
Screw Driver
(Type: TORX T20 H or
GTXH20-100)
POWER TRANSFORMER REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the oven door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads (primary and high voltage) from
power transformer and the filament leads from the
magnetron and capacitor terminals.
5. Remove four (4) screws holding transformer to bottom
plate.
6. Remove transformer from bottom plate.
Reinstallation
1. Rest transformer on the bottom plate with its primary
terminals toward the oven face plate.
2. Secure transformer with four screws to bottom plate.
3. Re-connect wire leads (primary and high voltage) to
power transformer and filament leads of transformer to
magnetron and high voltage capacitor. Refer to
"PICTORIAL DIAGRAM" on page 35.
4. Re-install outer case and check that oven is operating
properly.
HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the high voltage wire A from the high voltage
capacitor.
5. Disconnect the high voltage wire of high voltage rectifier
assembly from the magnetron.
6. Disconnect the filament lead (short one) of the power
transformer from the high voltage capacitor.
7. Remove one (1) screw holding capacitor holder with the
high voltage rectifier to the base plate.
8. Disconnect rectifier terminal from capacitor.
High voltage rectifier assembly is now free.
9. Remove capacitor holder. Capacitor is now free.
CAUTION: WHEN REPLACING HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR,
GROUND SIDE TERMINAL OF THE HIGH
VOLTAGE RECTIFIER MUST BE SECURED
FIRMLY WITH A GROUNDING SCREW.
MAGNETRON REMOVAL
Removal
1. Disconnect the power supply cord and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect wire leads from magnetron.
5. Remove the two (2) screws holding the chassis support
to the magnetron and the oven cavity front flange.
6. Slide the magnetron duct slightly so that the two (2)
screws at left hand side of the magnetron appear.
7. Carefully remove the four (4) screws holding magnetron
to waveguide flange.
8. Remove the magnetron with care so that the magnetron
antenna is not hit by any metal object around the antenna.
9. Now, the magnetron is free.
Reinstallation
1. Re-install the magnetron to waveguide flange with care
to prevent damage to the magnetron antenna.
2. Secure the magnetron with the four (4) screws.
3. Hold the chassis support to the oven cavity front plate
and the magnetron with the two (2) screws.
4. Reconnect the wire leads to the magnetron. Refer to
"PICTORIAL DIAGRAM" on page 35.
5. Re-install outer case and check that the oven is operating
properly.
CAUTION: WHEN REPLACING MAGNETRON, BE SURE
THE R.F. GASKET IS IN PLACE AND MOUNTING SCREWS ARE TIGHTENED SECURELY
28
DMT2420B
DMT2420R
DMT2420S
OVEN LAMP AND LAMP SOCKET REMOVAL
1.
2.
3.
4.
5.
Disconnect the power supply cord and remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Remove the oven lamp from the oven lamp socket.
Pull the wire leads from the oven lamp socket by pushing
the terminal hole of the oven lamp socket with the small
flat type screw driver.
6. Remove the oven lamp socket from the magnetron duct
by turning the socket counterclockwise.
7. Remove the oven lamp from the socket by turning the
oven lamp.
8. Now, the oven lamp and the oven lamp socket are free.
Oven lamp
socket
Terminal
Wire lead
Terminal hole
Flate type small
screw driver
Figure C-1. Oven lamp socket
POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL
Terminal
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock® connector.
5. Pull down on the positive lock® connector.
Positive lock®
connector
1
Push
Lever
®
CAUTION: WHEN CONNECTING THE POSITIVE LOCK
CONNECTORS TO THE TERMINALS, CONNECT THE POSITIVE LOCK® SO THAT THE
LEVER FACES YOU.
2
Pull down
Figure C-2. Positive lock® connector
CONTROL PANEL ASSEMBLY REMOVAL
3. Stick the key unit firmly to the control panel frame
by rubbing with soft cloth so not to scratch.
1. Disconnect the power supply cord and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from panel components.
5. Make one (1) tab of the oven cavity front plate straight
holding the control panel assembly to the oven cavity
front plate.
6. Slide the control panel assembly upward and remove it.
7. Now, individual components can be removed.
NOTE: 1. Before attaching a new key unit, wipe off remaining
adhesive on the control panel frame surfaces
completely with a soft cloth soaked in alcohol.
2. When attaching the key unit to the control panel
frame, adjust the upper edge and right edge of
the key unit to the correct position of control panel
frame.
LSI UNIT
NOTE: Handle the LSI unit carefully so that there is no
excessive force applied to the ribbon connection.
Liquid Crystal
Display (LCD)
Printed wiring board
of LSI unit
Ribbon cable
LSI unit
TURNTABLE MOTOR REMOVAL
1. Disconnect the power supply cord.
2. Remove turntable and turntable support from oven cavity.
3. Lay the oven on it's backside. Remove the turntable
motor cover by snipping off the material in four corners.
4. Where the corners have been snipped off bend corner
areas flat. No sharp edges must be evident after removal
of the turntable motor cover.
5. Disconnect wire leads from turntable motor.
(See "Positive lock connector removal")
6. Remove one (1) screw holding turntable motor to oven
cavity.
7. Now the turntable motor is free.
8. After replacement use the one (1) screw to fit the
turntable motor cover.
29
DMT2420B
DMT2420R
DMT2420S
COOLING FAN MOTOR REMOVAL
CAUTION:
* Do not reuse the removed fan blade because the
hole (for shaft) may be larger than normal.
REMOVAL
1. Disconnect the power supply cord and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the fan motor.
5. Remove the two (2) screws holding the fan motor to the
oven cavity back plate.
6. Remove the fan blade from the fan motor shaft according
to the following procedure.
7. Hold the edge of the rotor of the fan motor by using a pair
of groove joint pliers.
CAUTION:
* Make sure that no metal pieces enter the gap between
the rotor and the stator of the fan motor because the
rotor is easily shaven by pliers and metal pieces may
be produced.
* Do not touch the pliers to the coil of the fan motor
because the coil may be cut or damaged.
* Do not disfigure the bracket by touching with the
pliers.
8. Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
9. Now, the fan blade and the fan motor will be free.
INSTALLATION
1. Install the fan blade to the fan motor shaft according to
the following procedure.
2. Hold the center of the bracket which supports the shaft
of the fan motor on the flat table.
3. Apply the screw lock tight into the hole (for shaft) of the
fan blade.
4. Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
CAUTION:
* Do not hit the fan blade hard when installing because
the bracket may be damaged.
* Make sure that the fan blade rotates smoothly after
installation.
* Make sure that the axis of the shaft is not slanted.
5. Install the fan motor to the the oven cavity back plate with
the two (2) screws.
6. Connect the wire leads to the fan motor, referring to the
pictorial diagram.
Rear View
Shaft
Coil
Groove joint pliers
Shaft
Axis
Stator
Gap
Bracket
Stator
Rotor
These are the areas
that should be held
with a pliers
Table
Center of
bracket
Rotor
Side View
AH SENSOR REPLACEMENT
Removal
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the two (2) screws holding the AH sensor to the
sensor duct.
5. Disconnect the AH sensor harness from the connector
CN-F on control unit.
6. AH sensor is now free.
Reinstallation
1. Insert the new AH sensor into the sensor duct.
2. Install two (2) screws to secure the AH sensor.
3. Route the AH sensor harness across the oven cavity top
plate and through the large opening.
4. Connect the AH sensor harness to CN-F on control unit.
5. Re-install the outer case cabinet and check for proper
operation.
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
1.
2.
3.
4.
5.
6.
7.
Disconnect the power supply cord and remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect wire leads from the switches.
Remove two (2) screws holding latch hook to oven flange.
Remove latch hook assembly from oven flange.
Push outward on the two (2) retaining tabs holding switch
in place.
8. Switch is now free.
At this time switch lever will be free, do not lose it.
Re-install
1. Re-install each switch in its place. The secondary interlock/
monitor switches are in the lower position and the door
sensing switch is in the upper position.
2. Re-connect wire leads to each switch.
Refer to pictorial diagram.
30
DMT2420B
DMT2420R
DMT2420S
3. Secure latch hook (with two (2) mounting screws) to oven
flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit. Refer to chapter
"Test Procedure" and Adjustment procedure.
DOOR SENSING SWITCH/SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH ADJUSTMENT
1. Disconnect the power supply cord, and then remove outer
case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
If the door sensing switch, secondary interlock switch and
monitor switch do not operate properly due to a misadjustment,
the following adjustment should be made.
4. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
5. With door closed, adjust latch hook by moving it back and
forth, and up and down. In and out play of the door allowed
by the upper and lower position of the latch hook should
be less than 0.5mm. The vertical position of the latch hook
should be adjusted so that the door sensing switch and
primary interlock switch are activated with the door
closed. The horizontal position of the latch hook should be
adjusted so that the plunger of the monitor switch is
pressed with the door closed.
6. Secure the screws with washers firmly.
7. Check the operation of all switches. If each switch has not
activated with the door closed, loosen screw and adjust
the latch hook position.
hook, pushing and pulling upper portion of door toward the
oven face. Both results (play in the door) should be less
than 0.5mm.
2. The door sensing switch and secondary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Latch Heads
Door
Door Sensing
Switch
Monitor Switch
Switch Lever
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm when in
the latched position. First check upper position of latch
hook, pushing and pulling upper portion of door toward the
oven face. Then check lower portion of the latch
Secondary Interlock
Switch
Figure C-3. Latch Switch Adjustments
DOOR REPLACEMENT
REMOVAL
1. Disconnect the power supply cord.
2. Push the open button and open the door slightly.
3. Insert a putty knife (thickness of about 0.5mm) into the
gap between the choke cover and door frame as shown in
Figure C-4 to free engaging parts.
4. Pry the choke cover by inserting a putty knife as shown
in Figure C-4.
5. Release choke cover from door panel.
6. Now choke cover is free.
NOTE: When carrying out any repair to the door, do not
bend or warp the slit choke (tabs on the door
panelassembly) to prevent microwave leakage.
7. Release two (2) pins of door panel from two (2) holes of
upper and lower oven hinges by lifting up.
8. Now, door panel with door frame is free from oven cavity.
Choke Cover
Door Frame
Putty Knife
Figure C-4. Door Disassembly
9. Release the door panel from ten (10) tabs of door frame.
10.Remove the door panel from the door frame.
11.Now, door panel with sealer film is free.
12.Tear sealer film from door panel.
31
DMT2420B
DMT2420R
DMT2420S
Note:
13.Now, door panel is free.
14.Slide latch head upward and remove it from door frame by
releasing latch spring from door frame and latch head.
15.Now, latch head and latch spring are free.
16.Remove one (1) screw holding the door glass stopper to
the door frame.
17.Remove door glass stopper from door frame.
18.Slide the door glass rightwards and then slide upwards to
release the door glass from the tabs holding it.
19.Remove the door glass from the door frame.
20.Now, door frame is free.
REINSTALLATION
1. Re-install door glass to door frame as follows.
1-1. Insert the upper edge of the door glass into the five (5)
tabs of the door frame.
1-2. Slide the door glass downwards and insert the lower
edge of door glass into the five (5) tabs of the door
frame.
1-3. Slide the door glass leftwards and insert the left edge of
door glass into the two (2) tabs of the door frame.
2. Re-install the door glass stopper to the door frame so that
the two (2) holes of the door glass stopper fit to the two (2)
pins of the door frame. And hold the door glass stopper
with one (1) screw.
3. Re-install the latch spring to the latch head. Re-install the
latch spring to the door frame. Re-install latch head to door
frame.
4. Re-install door panel to door frame by catching ten (10)
tabs of door frame on the edges of door panel.
5. Put sealer film on door panel. Refer to “Sealer Film” about
how to handle new one.
6. Catch two (2) pins of door panel on two (2) hole of upper
and lower oven hinges.
7. Re-install choke cover to door panel by pushing.
Note: After any service to the door;
A) Make sure that door sensing switch and primary
interlock switch are operating properly. (Refer to
chapter “Test Procedures”.).
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
After any service, make sure of the following :
1. Door latch heads smoothly catch latch hook through latch
holes and that latch head goes through center of latch
hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity face
plate.
4. Check for microwave leakage around door with an approved
microwave survey meter. (Refer to Microwave
Measurement Procedure.)
The door on a microwave oven is designed to act as
an electronic seal preventing the leakage of microwave
energy from oven cavity during cook cycle. This
function does not require that door be air-tight,
moisture (condensation)-tight or light-tight. Therefore,
occasional appearance of moisture, light or sensing
of gentle warm air movement around oven door is not
abnormal and do not of themselves indicate a leakage
of microwave energy from oven cavity.
Pin
Upper
Oven Hinge
Upper Oven
Hinge
Lower
Oven Hinge
Lower Oven
Hinge
Pin
Choke Cover
Figure C-5. Door Replacement
SEALER FILM
Installation
1. Put the adhesive tape on the backing film of the sealer film
as shown in Fig. C-6.
2. Tear the backing film by pulling the adhesive tape.
3. Put the pasted side of the sealer film on the door panel
Sealer film
Backing film
Adhesive tape
Figure C-6. Sealer film
32
CN-G
CN-C
1
11
1
WHT
WHT
1
IC1
15
AH SENSOR
A
1
NOTE:
The grounding conductor of
the power supply cord has
been grounded by power
supply cord fixing screw.
The screw must always be
kept tight.
CAVITY TEMP. FUSE
CN-F
1 BLK
2 RED
3 WHT
B
C
D
E
F
G
H
CONTROL UNIT
H
N
RED
GRY
3
DOOR
SENSING
SWITCH
CN-F
(CPU UNIT)
N.O.
PNK
COM.
POWER SUPPLY
CORD 120V 60Hz
GRN
2
2
to Oven cavity
1
CN-C
CN-B
GRN
NOTE:
The neutral (WHT/GRY) wire must
be connected to the terminal with
"N" mark on the power supply
cord.
GRN
2
ORG
PRIMARY
INTERLOCK
RELAY
WHT
2 GRN
RY2
1 PNK
N.O.
BLU
OVEN LAMP
AND SOCKET
ORG
3
3
N.O.
COM
CN-A
COM
2
1
ORG
ORG
WHT
CN-B
RY1
BLUE MARK
NOTE:
Hot (ORG) wire must be
connected to the terminal
with blue mark on the oven
light socket.
T1
33
BRN
HIGH VOLTAGE COMPONENTS
RED
WHT
4
4
RED
FAN MOTOR
RED
WHT
N.C.
COM.
C/T
FUSE
TURNTABLE
MOTOR
MONITOR
SWITCH
HIGH VOLTAGE
WIRE A
MAGNETRON
COM.
BRN
WHT
WHT
GRY
WHT
WHT
WHT
HIGH
VOLTAGE
CAPACITOR
RED
5
5
WHT
SECONDARY NO
INTERLOCK
SWITCH
POWER
TRANSFORMER
H.V. RECTIFIER
BLK
6
6
A
B
C
D
E
F
G
H
DMT2420B
DMT2420R
DMT2420S
Figure S-1. Pictorial Diagram
DMT2420B
DMT2420R
DMT2420S
2
1
4
3
6
5
A
A
R2 91 1w
A2
C6
VA
C4
GND
C11
BZ/EN
C10
BUZZR
C9
OVEN LAMP
FAN MOTOR
TURNTABLE
MOTOR
B
b
AC120V
60Hz
–
R1
+
ZD1
HZ-16-1
a
D1
S1NB10
2.4k
1/4w
d
GND
C
(J1)
C
VR
Q1 KTC1027
D1
C2 1000µ/35v
A1
VRS1
CN-A
R3 91 1w
INT
C5
T1
10G471K
AC
C1
B
C3
c
SP30
D
OVEN LAMP
FAN MOTOR
TURNTABLE
MOTOR
RY1
NO
D
COM
AC
RY2
E
E
NO
MICRO
COM
C7
MICRO
C8
N.C
C2
N.C
C1
DOOR
SENSING
SWITCH
F
F
B2
G
DOOR
SENSING
SWITCH
B1
CN-C
11P LEAD WIRE HARNESS
NOTE
G
: IF NOT SPECIFIED, 0.1µF / 50V
H
H
Figure S-2. Power Unit Circuit
1
2
4
3
34
5
6
A
R10 470 1/2w
IC3
D81
R69 15k
C1
G2
G3
G5
SETUP
DEFROST
MICROWAVE
RECIPES &
INSTRUCTIONS
G6
PASTA
GRAINS
BEVERAGES
G13
G12
G11
R72 15k
POULTRY
G8
G9
G10
COM3
COM2
COM1
R90 43kF
R99 15k
C98
0.01µ
/25v
R100 4.7k
SEG3
SEG2
SEG1
COM50
COM49
IC4
SDA
SCL
WP
VCC
5
8
4 GND
A2
A1
1 A0
C110 0.01µ/25v
G14
COM51
SEG160
SEG159
SEG158
LIQUID CRYSTAL DISPLAY
100 x 160 Dots
C19 0.1µ/25v
R111
4.7k
R112
47k
R60 15k
R61 15k
R62 15k
R64 15k
R63 15k
G7
COM100
COM99
COM98
C112
0.1µ
/25v
STOP
CLEAR
VEGETABLES
FROZEN
FOOD
START
REHEAT
POPCORN
EASY
MINUTE
FISH
SEAFOOD
MEATS
KEY UNIT
NOTE :
: IF NOT SPECIFIED, 1/10W ± 5%
TOUCH SCREEN
6
6
G15
R73 15k
BAKED
POTATOES
G14
GND1
VLCD1
VCC1
V50
V40
V30
V20
V10
GREF
IREFM
IREFP
VLCD2
VLCD3
VCC2
GND2
GND3
VCC3
OSC1
OSC2
OSC
CO
DCON
CL1
FLM
M
M/S
RES
CS
RS
WR
RD
VCC4
GND4
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
VCC5
GND5
VCC6
VLCD4
GND6
IC5 IXA031DR
A13
A14
A15
A16
BYTE
GND
D15/A-1
D7
D14
R110
4.7k
G1
R70 15k
R71 15k
R65 15k
R66 15k
R67 15k
R74 270k
R75 270k
R76 270k
R77 270k
R78 270k
R79 270k
C60 330pF/50v
C61 330pF/50v
C62 330pF/50v
C63 330pF/50v
C64 330pF/50v
C65 330pF/50v
R68 15k
CN-C
C97 0.1µ/25v
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
5
5
D20
MA152WK
C95 0.1µ/25v
27
26
25
24
23
22
21
20
19
AN0
Vref
Avcc
MD2
MD1
MD0
LWR
HWR
RD
AS
Vcc
XTAL
EXTAL
Vss
NMI
RES
STBY
P67
P62
P61
WAIT
Vss
A19
A18
A17
A16
A15
A14
A13
A12
R98 1M
R113
150
1/2w
C21
0.1µ
/25v
18
17
16
15
14
13
12
11
10
9
8
7
6
5
R20 15k
C2
C94 0.1µ/25v
4
4
Q22
KRC101S
C93 0.1µ/25v
R92 20kF
0 ohm
(J80)
C22
10µ
/35v
C20
0.01µ
/25v
Q21
KRC101S
IC1 IXA029DR
H8/3006 ROM LESS
CHIP
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
IC2
IXA191DR
C96 0.1µ/25v
D6
D13
D5
D12
D4
VCC
VCC
GND
D11
D3
D10
D2
D9
D1
1
TI0CA2
2
A20
3
Vcc
4
TM00
5
PB1
6
PB2
7
PB3
8
PB4
9
PB5
10
PB6
11
PB7
12
RES0
13
Vss
14
TxD0
15
P91
16
RxD0
17
P93
18
P94
19
P95
20
P40
21
P41
22
P42
23
P43
24
Vss
25
P44
26
P45
27
P46
28
P47
29
D8
30
D9
VR
A11
A10
A9
A8
Vss
A7
A6
A5
A4
A3
A2
A1
A0
Vcc
D15
D14
D13
D12
D11
D10
Vcc
NC
R91 18kF
D80
R82
2k
1/2w
C130 0.01µ/25v
C15 0.1µ/25v
NC
VCC
V0
Cd
NC
NC
NC
GND
C16 0.01µ/25v
IC6
M51953AFP
R52 37.4kF
AN1
AN2
AN3
AN4
AN5
AN6
DA1
Avss
IR00
P81
P82
CS1
CS0
Vss
PA0
PA1
PA2
PA3
PA4
PA5
A12
A11
A10
A9
A8
NC
NC
A18
A17
A7
A6
A5
A4
41
A3
42
A2
43
A1
44
A0
45
CE
1
GND
2
0E
3
D0
4
D8
R30 3.3k
R51 75kF
Q20
KRA102S
C92 0.1µ/25v
3
28
29
30
31
32
33
34
35
36
37
38
39
40
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
R45 10k
D40 MA152WK
C30 10µ/35v
R44 360kF
-
3
35
C8
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
R49 300k
–
NC
CST12.00MTW
R48 620k
+
C7
CPU UNIT
C91 0.1µ/25v
C18
0.1µ
/25v
CF1
R50 150kF
D21
MA152WK
MICROR
(J13) 4.7k
R47 47k
Q32
KRC101S
C10
(J11)
(J12)
R46 47k
Q30 KRA101S
Q31
KRC101S
BUZZER ENV. C11
4
1
C41
0.015µ
/25v
(J10) 4.7k
2
+
–
C9
C13 47µ/16v
ZD10
UDZ5.6B
3
8
OVEN LAMP
TURNTABLE
MOTOR
FAN MOTOR
C14 0.01µ/25v
R11
1.2k
1/4w
C12 0.1µ/50v
C17 0.1µ/50v
IC3
+
7
4
2
2
F3
BUZZER
R80
4.7k
-
(R101) 4.7k
C40 0.1µ/50v
R41 3.32kD
C43 0.01µ/25v
F2
5
4
6
LED2
8
R13 4.7k
R43 1.8kF
F1
8
1
WH-1
LED1
Q12
KRC101S
C42 0.01µ/25v
AH SENSOR
–
WH-1
+
R21 4.7k
C3
+
R42
3.57kD
INT
C45 0.1µ/50v
C4
C44 0.1µ/50v
GND
R40 330 1w
–
C11 0.1µ/50v
C10 10µ/35v
+
Q80
KTC1027
1
1
5
C6
VA
TH1
5G2M40B333J
VCC
Q10 KTC1027
R81 20
VA
D80-81
1SS355
VR
DOOR
SENSING
SWITCH
B
C
D
E
F
G
H
C5
VR
A
B
C
D
E
F
G
H
DMT2420B
DMT2420R
DMT2420S
Figure S-3 LSI Unit Circuit
DMT2420B
DMT2420R
DMT2420S
2
1
4
3
6
5
A
A
VH
CN - B
B
1
B
CN - C
Q1 B
ZD1
SP30
R1
R2
DIP
C
SH-B
E
1
2
R3
SH-A
(GREEN)
11
C
C2
C1
D1
D
D20
D
OM
DU
1
7
D21
5
OM
DU
T1
3
XA
2
1
F
E
S
P
RY2
RY1
E
F
VRS1
2
(J1)
1
CN - A
VH
QKITPB033MREO
G
G
H
H
Figure S-4. Printed Wiring Board of Power Unit
1
2
4
3
36
5
6