U300
Administrator's Guide
Version 12.17.0.30
Yeastar Technology Co., Ltd.
MyPBX U300 Administrator's Guide
Table of Contents
1. Introduction ......................................................................................... 5
1.1 Features ......................................................................................... 6
1.2 Hardware Specifications .................................................................... 7
1.2.1 Exterior Appearance ...............................................................................7
2. System setup ....................................................................................... 7
2.1 Connection Drawing ......................................................................... 8
2.2 Connecting Ethernet Line .................................................................. 8
2.3 Supplying Power .............................................................................. 8
3 Administrator Login ............................................................................... 9
4 Status ................................................................................................ 10
4.1 Line status .................................................................................... 10
4.1.1 Extension Status .................................................................................. 10
4.1.2 Trunk Status ........................................................................................ 11
4.2 System Status ............................................................................... 11
4.2.1 System Info ......................................................................................... 12
4.2.2 Network Status .................................................................................... 12
5 System .............................................................................................. 13
5.1 Network Preferences ...................................................................... 13
5.1.1 LAN Settings ........................................................................................ 13
5.1.2 WAN Settings ....................................................................................... 14
5.1.3 DHCP Server ........................................................................................ 15
5.1.4 VLAN Settings ...................................................................................... 16
5.1.5 VPN Settings ........................................................................................ 19
5.1.6 DDNS Settings ..................................................................................... 19
5.1.7 Static Route ......................................................................................... 20
5.2 Firewall Settings ............................................................................ 21
5.2.1 Firewall Rules ....................................................................................... 21
5.2.2 IP blacklist ........................................................................................... 23
5.3 System Preference ......................................................................... 24
5.3.1 Password Settings ................................................................................ 24
5.3.2 Date and Time ..................................................................................... 25
5.3.3 Firmware Update .................................................................................. 26
5.3.4 Hot Standby ........................................................................................ 26
5.3.5 Backup and Restore .............................................................................. 28
5.3.6 Reset and Reboot ................................................................................. 28
5.3.7 Alert Settings ....................................................................................... 29
5.3.8 Addons ............................................................................................... 31
5.4 Storage Management ..................................................................... 32
5.4.1 External Storage .................................................................................. 32
6 PBX ................................................................................................... 35
6.1 Extensions .................................................................................... 35
6.1.1 FXS/VoIP Extensions ............................................................................. 35
www.yeastar.com
Page2
MyPBX U300 Administrator's Guide
FXS Extensions .................................................................................... 35
VoIP Extensions ................................................................................... 40
6.1.2 Phone Provisioning ............................................................................... 45
6.2 Trunks .......................................................................................... 54
6.2.1 Physical Trunk ...................................................................................... 54
6.2.2 VoIP Trunk ........................................................................................... 58
6.3 Outbound Call Control .................................................................... 64
6.3.1 Outbound Routes.................................................................................. 64
6.3.2Speed Dial Settings ............................................................................... 66
6.4 Inbound Call Control ...................................................................... 67
6.4.1 IVR ..................................................................................................... 67
6.4.2 Ring Groups ......................................................................................... 70
6.4.3 Queues ............................................................................................... 71
6.4.4 Conferences ......................................................................................... 75
6.4.5 Inbound Routes .................................................................................... 75
6.5 Audio Settings ............................................................................... 80
6.5.1 Custom Prompts ................................................................................... 80
6.5.2 Music on Hold Prompts .......................................................................... 81
6.5.3 System Prompts Settings ...................................................................... 82
6.6 Basic Settings................................................................................ 82
6.6.1 General Preferences .............................................................................. 83
6.6.2 Business Hours .................................................................................... 85
6.6.3 Feature Codes ...................................................................................... 86
6.6.4 Voicemail Settings ................................................................................ 89
6.7 Advanced Settings ......................................................................... 92
6.7.1 SIP Settings......................................................................................... 92
6.7.2 IAX Settings ........................................................................................ 98
6.7.3 Blacklist .............................................................................................. 99
6.7.4 Callback Settings ................................................................................ 100
6.7.5 DNIS Settings .................................................................................... 101
6.7.6 DISA ................................................................................................. 102
6.7.5 PIN User Settings ............................................................................... 103
6.7.8 Paging Groups.................................................................................... 105
7 Reports ............................................................................................ 107
7.1 Call Logs ..................................................................................... 107
7.2 System Logs ............................................................................... 107
8 Logout ............................................................................................. 108
9. Use MyPBX ...................................................................................... 109
9.1 Make outbound call ...................................................................... 109
9.1.1 Sample Routing via E1 Trunk ............................................................... 109
9.1.2 Sample Routing via VoIP Trunk ............................................................. 110
9.2 Incoming call............................................................................... 112
9.2.1 Sample Routing to an IVR .................................................................... 112
www.yeastar.com
Page3
MyPBX U300 Administrator's Guide
APPENDIX A FAQ .................................................................................. 115
APPENDIX B How to Configure Autobackup .............................................. 116
APPENDIX C How to Configure NAT setting .............................................. 118
APPENDIX D How to Use Auto Provision .................................................. 120
APPENDIX E HowDo I Configure Distinctive Ring Tones ............................. 123
APPENDIX F How to Use DID ................................................................. 125
APPENDIX G MyPBX Security configuration Guide ..................................... 129
1. Security Configuration for Web GUI .................................................. 129
1.1 Change the default access port for HTTP on Options page .......................... 129
1.2 Change the default password for the web GUI .......................................... 130
2. Disable SSH on LAN Settings Page ................................................... 130
2.1 Disable SSH.......................................................................................... 130
2.2 Change the default password for SSH ...................................................... 131
3. Security Configuration for Extensions ............................................... 132
3.1 Change the default SIP Port .................................................................... 132
3.2*Disable guest calls ................................................................................ 133
3.3* Security Configuration for remote extensions .......................................... 134
3.4 Set an enhanced password and enable IP restriction for extensions ............. 134
4. Setup Proper Firewall Rules ............................................................. 135
5*. Alert Settings .............................................................................. 142
5.1 IPATTACK ............................................................................................. 143
5.2 WEBLOGIN ........................................................................................... 144
6. Note ............................................................................................ 145
www.yeastar.com
Page4
MyPBX U300 Administrator's Guide
1. Introduction
MyPBX
—IP-PBX for Medium Businesses/Home Office
MyPBX U300 is a standalone embedded hybrid PBX for medium businesses and
remote branch offices of larger organizations (1-100 users per site). MyPBX
U300 also offers a hybrid solution (a combination of VoIP applications using
E1/T1/J1 equipment) alternative for enterprises who are not yet ready to
migrate to a complete VoIP solution.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radiofrequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user‟s authority to operate this equipment.
FCC Warning
This equipment has been tested and found to comply with the regulations for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received including interference
that may cause undesired operation.
www.yeastar.com
Page5
MyPBX U300 Administrator's Guide
1.1 Features
● Auto-provision
● Follow me
● Audio In/Out
● Interactive Voice Response (IVR)
● BLF Support
● Intercom / Zone Intercom
● Blacklist
● Music On Hold
● Call transfer
● Music On Transfer
● Call Detail Records(CDR)
● Paging / Zone Paging
● Call Forward
● PIN Users
● Call Parking
● Queue
● Call Recording
● QOS
● Call Pickup
● Ring Group
● Call Routing
● Route by Caller ID
● Call Transfer
● Spy functions
● Call Waiting
● Skype Integration (Skype Connect)
● Caller ID
● Three-way Calling
● Call Back
● Mobility Extension
● Conference
● External Storage
● Speed Dial
● DDNS
● Define Office Time
● OpenVPN
● Direct Inward System Access(DISA)
● T.38
● DIDs
● Voicemail
● Distinctive Ringtone
● VLAN
● Do Not Disturb(DND)
● WAN
● Dial by Name
● PPPoE
● Firewalls
● Static Route
● Alert
● Multiple administrators
● Integrated built-in packet capture tools
● Blind Transfer
More info, please click: http://www.yeastar.com/Products/MyPBX-U300.asp
www.yeastar.com
Page6
MyPBX U300 Administrator's Guide
1.2 Hardware Specifications
1.2.1 Exterior Appearance
Front Panel
①
②
③
④
⑤
⑥
⑦
⑧
Figure1-1 MyPBX U300 Front Panel
No.
Indication
①
Reset button: Press until all LEDs turn orange, which means the reset
is completed.
②
Power LED: Green stably
Run LED: Green Blinking
③
Audio in interface
Audio out interface
④
USB 2.0 port
⑤
WAN port
LAN port
⑥
Console port (RJ45)
⑦
E1/T1 interface
⑧⑨
Two fixed FXS ports(RJ11)
2. System setup
www.yeastar.com
Page7
⑨
MyPBX U300 Administrator's Guide
2.1 Connection Drawing
Figure 2-1
2.2 Connecting Ethernet Line
MyPBX provides two 10/100MEthernet ports with RJ45 interface and LED
indicator. Plug Ethernet line into MyPBX‟s Ethernet port, and then connect the
other end of the Ethernet line with a hub, switch, router, LAN or WAN. Once
connected, check the status of the LED indicator. A yellow LED indicates the port
is in the connection process, and a green LED indicates the port is properly
connected.
2.3 Supplying Power
Please follow the steps below to connect the MyPBX unit to a power outlet:
1. Connect the small end of the power cable to the power input port on the
MyPBX back panel, and plug the other end of the cable into a 100V~240V
AC power outlet.
2. Check the Power LED on the front panel. A solid green LED indicates that
power is being supplied correctly.
www.yeastar.com
Page8
MyPBX U300 Administrator's Guide
3 Administrator Login
From your web browser, input the IP address of the MyPBX server.
If this is the first time you are configuring MyPBX, please use the default settings
below (your PC should be in the same local network with MyPBX):
IP Address: http://192.168.5.150
Username: admin
Password: password
In this example, the IP address is 192.168.5.193
Figure 3-1
This is the welcome page of MyPBX U300 after successful login.
Figure 3-2
www.yeastar.com
Page9
MyPBX U300 Administrator's Guide
4 Status
Click
to start to check the status of MyPBX U300,where we can check
the status of extension, trunk, network and system information.
4.1 Line status
In this page, we can check the status of extension and trunks
4.1.1 Extension Status
Figure 4-1
MyPBX Status Description:
Extensions:
1)
: Extension is unavailable
2)
:Extension is idle
3)
:Extension is ringing
4)
:Extension is busy
5)
: Extension is on hold
www.yeastar.com
Page10
MyPBX U300 Administrator's Guide
4.1.2 Trunk Status
Figure 4-2
Trunks:
VOIP Trunk:
Status
Unregistered: Trunk registration failed.
Registered: Successful registration, trunk is ready for use.
Request Send: Registering.
Waiting: Waiting for authentication.
Service Provider:
Status
OK: Successful registration, trunk is ready for use.
Unreachable: The trunk is unreachable.
Failed: Trunk registration failed.
E1 Trunk:
Connect
Alarm
Comment
The port doesn‟t have E1 line connected.
E1 line has been connected to the port; PRI is in
corresponding or can‟t communicate.
Succeed.
4.2 System Status
In this page, we can check the status of MyPBX system, including the hardware,
firmware version and the network status of LAN and WAN ports .
www.yeastar.com
Page11
MyPBX U300 Administrator's Guide
4.2.1 System Info
In this page, we can check the hardware/firmware version, or the disk usage of
MyPBX.
Figure 4-3
4.2.2 Network Status
In this page, the IP address of LAN and WAN port will appear, if OpenVPN and
Vlan are configured well, they will be display here too.
Figure 4-4
www.yeastar.com
Page12
MyPBX U300 Administrator's Guide
5 System
Click
to access.
In this page, we can configure the network settings, firewall settings, storage
management and some other preferences like firmware update and hot
standby.
5.1 Network Preferences
5.1.1 LAN Settings
Figure 5-1
·
DHCP
If this option is set, MyPBX will use DHCP to get an available IP address from
your local network. Not recommended or you cannot access MyPBX without
the right IP address
·
Enable SSH
This is the advance way to access the device, you can use the putty software
to access the device.In the SSH access, you can do more advance setting
and debug. Disabled by default.
·
Port: the default is 8022, you change it to another one
·
Hostname
www.yeastar.com
Page13
MyPBX U300 Administrator's Guide
Set the host name for MyPBX.
·
IP Address
Set the IP Address for MyPBX.
Recommend to configure a static IP address for MyPBX
·
Subnet Mask
Set the subnet mask for MyPBX.
·
Gateway
Set the gateway for MyPBX.
·
Primary DNS
Set the primary DNS for MyPBX.
·
Secondary DNS
Set the secondary DNS for MyPBX.
·
IP Address2
Set the second IP Address for MyPBX.
·
Subnet Mask2
Set the second subnet mask for MyPBX.
5.1.2 WAN Settings
Figure 5-2
It support three connection types: DHCP (obtain an IP automatically), PPPoE,
Static IP Address.
www.yeastar.com
Page14
MyPBX U300 Administrator's Guide
Note:
1. WAN port is disabled by default
2. WAN port cannot be used as a router to route the internet packages from
WAN port to LAN port.
·
DHCP
.If your ISP says that you are connecting through DHCP or a dynamic IP address
from your ISP, perform these steps:
Step1: Select DHCP as the WAN Connection Type.
Step2: Click Save button to save the settings.
Step3: Reboot the device.
Step4: Check the WAN‟s Status (Status Network status).
·
Static IP Address
If your ISP says that you are connecting through a static or fixed IP address
from your ISP, perform these steps:
Step1: Select Static IP Address as the WAN Connection Type.
Step2: Enter the IP Address.
Step3: Enter the Subnet Mask.
Step4: Enter the Gateway Address.
Step5: Enter the Primary DNS and Secondary DNS.
Step6: Click the Save button to save the settings.
Step7: Reboot the device.
Step8: Check the WAN‟s Status (Status Network status).
·
PPPoE
If your DSL provider says that you are connecting through PPPoE or if you
normally enter a user name and password to access the Internet, perform these
steps:
Step1: Select PPPoE as the WAN Connection Type.
Step2: Enter the User Name.
Step3: Enter the Password.
Step4: Click the Save button to save the settings.
Step5: Reboot the device.
Step6: Check the WAN‟s Status (Status Network status)
5.1.3 DHCP Server
Dynamic Host Configuration Protocol (DHCP) is a network protocol that enables
a server to automatically assign an IP address to a computer from a defined
range of numbers (i.e., a scope) configured for a given network. You can set a
local network NTP server for MyPBX here too
www.yeastar.com
Page15
MyPBX U300 Administrator's Guide
Note: MyPBX U300 can be working as a DHCP server, but cannot be regarded as
an router. When using „Phone Provisioning‟ for Grandstream IP phone, Enter the
IP address of the server directly, e.g.:192.168.5.150; for other phones using
the default configuration.
Figure 5-3
5.1.4 VLAN Settings
A VLAN(Virtual LAN) is a logical local area network (or LAN) that extends beyond
a single traditional LAN to a group of LAN segments, given specific
configurations.
Note:
MyPBX U300 is not the VLAN server, a 3-layer switch is still needed, please
configure the VLAN information there first, then input the details in MyPBX, so
that the packages via MyPBX will be added the VLAN label before sending to that
switch.
www.yeastar.com
Page16
MyPBX U300 Administrator's Guide
Figure 5-4
1) VLAN Over Lan
·
NO.1
Click the NO.1 you can edit the first VLAN over Lan.
·
VLAN Number
.The VLAN Number is a unique value you assign to each VLAN on a single device.
·
VLAN IP Address
Set the IP Address for MyPBX VLAN over Lan.
·
VLAN Subnet Mask
Set the Subnet Mask for MyPBX VLAN over Lan.
·
Default Gateway
Set the Default Gateway for MyPBX VLAN over Lan
·
NO.2
Click the NO.2 you can edit the first VLAN over Lan.
·
VLAN Number
www.yeastar.com
Page17
MyPBX U300 Administrator's Guide
.The VLAN Number is a unique value you assign to each VLAN on a single device.
·
VLAN IP Address
Set the IP Address for MyPBX VLAN over Lan.
·
VLAN Subnet Mask
Set the Subnet Mask for MyPBX VLAN over Lan.
·
Default Gateway
Set the Default Gateway for MyPBX VLAN over Lan.
2) VLAN Over Wan
·
NO.1
Click the NO.1 you can edit the first VLAN over Wan.
·
VLAN Number
.The VLAN Number is a unique value you assign to each VLAN on a single device.
·
VLAN IP Address
Set the IP Address for MyPBX VLAN over Wan.
·
VLAN Subnet Mask
Set the Subnet Mask for MyPBX VLAN over Wan.
·
Default Gateway
Set the Default Gateway for MyPBX VLAN over Wan.
·
NO.2
Click the NO.2 you can edit the first VLAN over Wan.
·
VLAN Number
.The VLAN Number is a unique value you assign to each VLAN on a single device.
·
VLAN IP Address
Set the IP Address for MyPBX VLAN over Wan.
·
VLAN Subnet Mask
Set the Subnet Mask for MyPBX VLAN over Wan.
·
Default Gateway
Set the Default Gateway for MyPBX VLAN over Wan.
www.yeastar.com
Page18
MyPBX U300 Administrator's Guide
5.1.5 VPN Settings
A virtual private network (VPN) is a method of computer networking--typically
using the public internet--that allows users to privately share information
between remote locations, or between a remote location and a business' home
network. A VPN can provide secure information transport by authenticating
users, and encrypting data to prevent unauthorized persons from reading the
information transmitted. The VPN can be used to send any kind of network
traffic securely. MyPBX supports OpenVPN.
Figure 5-5
·
Enable VPN
·
Import VPN Config
Import configuration file of OpenVPN.
Note: Don't configure 'user' and 'group' in the 'config' file.
You can get the config package from the OpenVPN provider.
5.1.6 DDNS Settings
DDNS(Dynamic DNS) is a method / protocol / network service that provides the
capability for a networked device, such as a router or computer system using
the Internet Protocol Suite, to notify a Domain Name System (DNS) name
server to change, in real time, the active DNS configuration of its configured
hostnames, addresses or other information.
Figure 5-6
www.yeastar.com
Page19
MyPBX U300 Administrator's Guide
·
Enable DDNS
·
DDNS Server
Select the DDNS server you sign up for service.
·
User Name
User name the DDNS server provides you. This field is allowed to input 63
characters.
·
Password
User account‟s password .
·
Host Name
Note: DDNS allows you to access your network using domain names instead of
IP address. The service manages changing IP address and updates your domain
information dynamically. You must sign up for service through dyndns.org,
freedns.afraid.org, www.no-ip.com, www.zoneedit.com
5.1.7 Static Route
MyPBX will have more than one internet connection in some situations but it has
only one default gateway. You will need to set some Static Route for MyPBX to
force it goes out through different gateway when access to different internet.
The default gateway priority of MyPBX from high to low is OpenVPNWAN
portLAN port.
Figure 5-7
1) Route table
The current route rules of MyPBX
·
Destination
The destination network to be accessed to by MyPBX
www.yeastar.com
Page20
MyPBX U300 Administrator's Guide
·
Subnet Mask
Specify the destination network portion.
·
Gateway
Define which gateway MyPBX will go through when access to the destination
network.
·
Metric
The cost of a route is calculated by using what are called routing metric. Routing
metrics are assigned to routes by routing protocols to provide measurable
statistic which can be used to judge how useful (how low cost) a route is.
·
Interface
Define which internet port to go through.
2) Static Route Rules
You can add new static route rules here.
5.2 Firewall Settings
Firewalls are used to prevent unauthorized Internet users from accessing
private networks connected to the Internet, especially intranets. All
messages entering or leaving the intranet pass through the firewall, which
examines each message and blocks those that do not meet the specified
security criteria.
5.2.1 Firewall Rules
Figure 5-8
www.yeastar.com
Page21
MyPBX U300 Administrator's Guide
1) General Settings
·
Enable Firewall
Enable the firewall to protect the device. You should reboot the device to
make the firewall run successfully.
·
Disable Ping
Enable this item, net ping from remote hosts will be dropped.
·
Drop All
When you enable „Drop All‟ feature, system will drop all packets or connection
from other hosts if there are no other rules defined. To avoid locking the devices,
at least one „TCP‟ accept common rule must be created for port used for SSH
access, port used for HTTP access and port sued for CGI access.
2) Common Rules
There is not default rules inside, you can create them as required
Figure 5-9
·
Name
A name for this rule, e.g. „HTTP‟.
·
Description
Simple description for this rule. E.g.: Accept the specific host to access the web
interface for configuration.
·
Protocol
The protocols for this rule.
·
Port
Initial port should be on the left and end port should be on the right.
The end port must be equal to or greater than start port.
www.yeastar.com
Page22
MyPBX U300 Administrator's Guide
·
IP
The IP address for this rule. The format of IP address is: IP/mask
Ex:192.168.5.100/255.255.255.255forIP 192.168.5.100
Ex:216.207.245.47/255.255.255.255 for IP 216.207.245.47
Ex:192.168.5.0/255.255.255.0 for IP from 192.168.5.0 to 192.168.5.255 .
·
MAC Address
The format of MAC Address is XX:XX:XX:XX:XX:XX, X means 0~9 or A~F in hex,
the A~F are not case sensitive.
Note: The MAC address will be changed when it‟s remotely device, so it will
not be working to filter using MAC for remote devices.
·
Action
Accept: Accept the access from remote hosts.
Drop: Drop the access from remote hosts.
Ignore: Ignore the access.
5.2.2 IP blacklist
You can set some packets accept speed rules here. When a IP address which
hasn‟t been accepted in common rules sends packets faster than the allowed
speed, it will be set as black IP address and blocked automatically.
Figure 5-10
1) Blacklist rules
We can add the rules for IP blacklist rate as your demand
Figure 5-11
www.yeastar.com
Page23
MyPBX U300 Administrator's Guide
·
Port
Auto defense port
·
Protocol
Auto defense protocol. TCP or UDP.
·
IP Packets
Allowed IP packets number in the specific time interval.
·
Time interval
The time interval to receive IP packets. For example, IP packets 90,time
interval 60 means 90 IP packets are allowed in 60 seconds.
2) IP blacklist
The blocked IP address will display here, you can edit or delete it as your wish.
5.3 System Preference
In this page, we can set other system preference, like the password for admin
account, system date and time, firmware update, hot standby, backup and
restore, reset and reboot.
5.3.1 Password Settings
1) Change Password
•User
MyPBX support 3 levels users, choose one of them to change its password.
Administrator: have all authority
User Administrator: have basic authority; without the advanced authority to
reset, update, backup and restore MyPBX.
CDR Administrator: only have the authority to check the call recordings.
•Enter Old Password
The default password of all users is „password‟.
•Enter New Password
•Retype New Password
To change the password, enter the new password and click update. The system
will then prompt you re-login using your new password.
www.yeastar.com
Page24
MyPBX U300 Administrator's Guide
2) CDR settings
Whether enable CDR User.
Note: To logon MyPBX with CDR Administrator, enable CDR user first.
Figure 5-12
5.3.2 Date and Time
Set the date and time for MyPBX.
Figure 5-13
·
Time Zone
You can choose your time zone here.
·
Daylight Saving Time
Set the mode to Automatic or disabled
·
Automatically Synchronize With an Internet Time Server
Input the NTP server so that MyPBX will update the time automatically
·
Set Date & Time Manually
You can set the time to your local right time manually here
www.yeastar.com
Page25
MyPBX U300 Administrator's Guide
5.3.3 Firmware Update
Upgrading of the firmware is possible through the Administrator web interface
using a TFTP Server or an HTTP URL.
Enter your TFTP Server IP address and firmware file location, then click start to
update the firmware
Note:
1. If enabled „Reset configuration to Factory Defaults‟, System will restore to
factory default settings.
2. When update the firmware, please don‟t turn off the power. Or the system will
get damaged.
3. More information for the steps to update the firmware, please refer to this link:
http://www.yeastar.com/download/MyPBX_U300_FirmwareUpgrade_en.pdf
Figure 5-14
5.3.4 Hot Standby
Redundancy is achieved by using duplicate hardware and software installations
and synchronizing data and operating state. Redundancy assures smooth
operation even if a system goes down. Essentially a duplicate backup system
takes over with virtual no loss of service. This technique assures absolute
reliability no matter what failure occurs. In mission critical installations,
redundancy is a way to address possibility of any failure.
Note 1: Before enabling the Host Standby feature, please make sure that the
two servers in the failover pair are the same model, have the same modules
installed in the same slots, the same hardware configurations and firmware
version.
Note 2: Please configure the primary server first and configure the secondary
server only after the running status of primary server becomes “active”.
Note 3: The virtual IP address inputted in this page will be the one used for
registering in each IP phone.
Note 4: Before configure the Email list in this page, please configure the
„voicemail settings‟ in “PBXBasic settings”, make sure the SMTP testing
successfully.
www.yeastar.com
Page26
MyPBX U300 Administrator's Guide
Figure 5-15
Mode: Primary means the main unit; Secondary means the standby unit;
Secondary/Primary Hostname: If this unit mode is primary, then you need
to input the hostname of standby unit; vise versa, if this unit is selected as
secondary, then the hostname of primary unit is required. In brief, you need to
input each other‟s host name on this field.
IP: You need to input each other‟s IP address on this field.
Access code: To make an identification number to verify each other. The
number must be the same to both units.
Virtual IP address: To fill in a virtual IP address includes mask, which is
always points to the currently activated unit. Customer can register IP phones
through this virtual IP address. Please make sure the virtual IP add includes
mask is the same on both units but different from their former IP address.
Network Connection Detection:Generally it requires the IP address of the
router or gateway that connects both units. MyPBX will connect another unit
through this IP address.
Down Notification:The way of informing customer that the system down.
Keep Alive: Every 2 seconds, a package will be sent from one unit to another,
which can test whether they are working properly.
Dead Time: The default setting is 120 seconds. If there‟s no response within
120s after one receiving a package from the other, then the normal working unit
will figure the other unit is dead and send an email to report the failure.
www.yeastar.com
Page27
MyPBX U300 Administrator's Guide
5.3.5 Backup and Restore
We can backup up the configurations before reset MyPBX U300 to factory
defaults, and then restore it using this package.
Note:
1. Only configurations, custom prompts will be backed up, the voicemail and
recording files are not included.
2. When you have update the firmware version, it‟s not recommend to restore
using old package.
Figure 5-16
5.3.6 Reset and Reboot
We can reset or reboot MyPBX U300 via web directly in this page .
Figure 5-17
·
Reboot System
Warning: Rebooting the system will terminate all active calls!
·
Reset to Factory Defaults
Warning: A factory reset will erase all configuration data on the system.
Please do not turn off the system until the RUN light begins blinking. Any power
interruption during this time could cause damage to the system.
www.yeastar.com
Page28
MyPBX U300 Administrator's Guide
5.3.7 Alert Settings
If the device is attacked, the system will notify users the alert via call or E-mail.
The attack mode includes IP attack and Web Login.
More details for the system security configuration please refer to APPENDIX G
MyPBX Security Configuration Guide.
Figure 5.3.7.1
IPATTACK
When the system is attacked by an IP address, the firewall will add the IP to auto
IP Blacklist and notify the user if it matches the protection rule.
Note: Please ensure that all voicemail settings are properly configured on the
System Settings -> Voicemail Settings page before using Emails alert.
1) Phone Notification Settings
·
Phone Notification:
Enable or disable phone notification
·
Number
The numbers to call sending alert notification. Users can setup multiple
extensions and outbound phone numbers. Please separate them by „;‟.
e.g. „500;81234‟. If the extension has configured Follow Me Settings, the call
would go to the forwarded number directly.
·
Attempts
The attempts to dial the Number when there is no answer.
·
Interval
The interval between each attempt to dial the phone number. Must be greater
than 3 seconds
·
Prompts
2) E-mail Notification Settings
·
E-mail Notification
Enable or disable email notification
www.yeastar.com
Page29
MyPBX U300 Administrator's Guide
·
To
Multiple mail address are allowed; please separate them by „;‟, e.g.
123@gmail.com;456@hotmail.com.
·
Subject
The subject of email
·
Content
Text content, support for predefined variables, Variable names
corresponding instructions are as follows:
$(HOSTNAME) host name
$(LOCALIP) local IP address
$(SOURCEIP) attack source IP address
$(DESTMAC) attacks destination mac (IPATTACK effective)
$(DESTPORT) attacks destination port number (IPATTACK effective)
$(PROTOCOL) protocol type (IPATTACK effective)
$(DATETIME) occurred
$(USERNAME) user name (WEBLOGIN effective)
$(INTERFACE) network interface name (IPATTACK effective)
and
Figure 5.3.7.2
www.yeastar.com
Page30
MyPBX U300 Administrator's Guide
WEBLOGIN
Enter the password incorrectly five times to login MyPBX interface will be
regarded as attack. The system will limit the IP login within 10 minutes and
notify the user.
Figure 5.3.7.3
5.3.8 Addons
Call Recording enables all your inbound and outbound phone calls to be
recorded. The system would detect any call conversation and record them
automatically. The call recordings would be saved in the folder you specify and
stored in the USB.
And if users want to use the function call recording, they need active this
function firstly.
Note: For usage of the addon feature, please purchase activation code from
your equipment provider.
www.yeastar.com
Page31
MyPBX U300 Administrator's Guide
Figure 2.3.8.1
After activation, the page will show as below:
Figure 2.3.8.2
5.4 Storage Management
5.4.1 External Storage
The External Storage feature is used to extend storage space. Once configured,
the files (voicemail, call recording files) created before the configured days will
be moved to the Net-Disk.
Note: The shared folder must be based on Windows operation system.
Before external storage can be properly configured, an SMB share folder
accessible from MyPBX must be set up on a Windows based machine. Once
that has been set up, please follow the steps below.
www.yeastar.com
Page32
MyPBX U300 Administrator's Guide
Figure 5-18
Step
Step
Step
Step
1:
2:
3:
4:
Choose a window-based computer that is always in service
Create a folder
Create a text file named "status.txt" in the folder
Share this folder
Then we need input the Net-Disk information in step2 page.
Figure 5-19
Net-Disk Host/IP:Change this to the IP address of the computer where
backup files will be stored.
Net-DiskShare Name: Change this to the name of the shared folder where
backups will be stored.
www.yeastar.com
Page33
MyPBX U300 Administrator's Guide
Net-DiskShare Username: The user name used to log into the network
share. Leave this blank if it is not required
Net-DiskShare Password: The password used to log into the network
share.Leave this blank if it is not required
If configuringis correctly, open your Windows share folder to see if the
MyPBX backup files and folders has been created.If the contents of the
backup folder look similar to step3 page, then you have successfully
configured external storage on the MyPBX unit.
Figure 5-20
www.yeastar.com
Page34
MyPBX U300 Administrator's Guide
6 PBX
Click
to access
In this page, we can configure the settings of extension, trunk, inbound call
control, outbound call control, audio settings and the others. When configured
well, we can make calls as scheduled
6.1 Extensions
In this page, we can configure the extensions‟ details and provision the
supported models automatically.
6.1.1 FXS/VoIP Extensions
There are three types of extensions supported in MyPBX U300: SIP, IAX and
analog extension.
Note:
1. The number of SIP/IAX extension is 100
2. The number of FXS extension is only 2 ( fixed)
Figure 6-1
FXS Extensions
www.yeastar.com
Page35
MyPBX U300 Administrator's Guide
Figure 6-2
There are two fixed analog extensions in MyPBX U300, to modify the extension
number, please delete it first, then recreate it again
1) General
Figure 6-3
·
Extension
The numbered extension, i.e. 1234, that will be associated with this particular
User / Phone.
·
Port
The extension correspond port.
·
Name
A character-based name for this user, i.e. „Bob Jones‟ .
·
Caller ID
www.yeastar.com
Page36
MyPBX U300 Administrator's Guide
The Caller ID (CID) string will be used when this user calls another internal user.
2) Voicemail
·
Enable Voicemail
Check this box if the user should have a voicemail account.
·
Voicemail Access PIN #
Voicemail Password for this extension, i.e. „1234‟.
3) Mail Setting
·
Enable Send Voicemail
Once enabled, the voicemail will be sent to the belowemail address as an
attachment.
·
Send Voicemail to Email Address
This option defines whether or not voicemails/Fax is sent to the Email address
asan attachment.
Note: Please ensure that all voicemail settings are properly configured on the
System Settings -> Voicemail Settings page before using this feature.
4) Flash
·
Hook Flash Detection
Sets the amount of time, in milliseconds, that must pass since the last
hook-flash event received by MyPBX before it will recognize a second event. If a
second event occurs in less time than defined byHook Flash Detection, then
MyPBX will ignore the event. The default value of Flash is 1000 ms, and it can be
configured in 1ms increments.
5) Group
·
Pickup Group
If this extension belongs to a pickup group, any calls that ring this extension can
be picked up by other extensions in the same pickup group by dialing the Call
Pickup feature code (default *4).
Note: *4 is the default setting, it can be changed under Feature Codes ->
General -> Call Pickup.
6) Call Duration Settings
Setup the max cull duration for every call of this extension, but it‟s only valid for
outbound calls. And if enter „0‟ or leave this blank empty, the value would be
equal to the max call duration configured in the Option Settings page.
Note: This setting will not be valid for internal calls.
www.yeastar.com
Page37
MyPBX U300 Administrator's Guide
7) Other options
·
Call Waiting
Check this option if the extension should have Call Waiting capability.If this
option is checked, the „When busy‟ follow me options will not be available.
·
DND
Don‟t Disturb.
·
User Web Interface
Check this option to allow the user to login to the MyPBX User Web interface,
which can be used to access voicemail and extension recordings. Users may
login to the MyPBX User Web interface by using their extension number and
voicemail PIN # as the login and password respectively.
·
Ring Out
Check this option if you want to custom the ring time. Tone will stop over the
time defined
8) Follow me (Call Forwarding)
This function sets inbound call forwarding on an extension. An administrator can
configure Follow Me for this extension
9) Volume Settings
Rxgain: The Volume sent to FXS extension.
Txgain: The Volume sent out by the FXS extension
10) Mobility Extension
MyPBX allows you to use your mobile phone as extension. If you set your mobile
phone as mobility extension and then you call MyPBX with this mobility phone,
you will hear a dial tone. MyPBX will recognize your call as a call from an
extension. You can dial the number of other extensions (Your caller ID will be
the number of your extension) or dial out via outbound routes just like dialing
from your extension.
Note: If callback is enabled in the inbound route, the mobility extension
function of this inbound route will be disabled
11) Spy Settings
MyPBX allows extension to monitor/barge in other conversation. Once this
feature is enabled, the extension has the ability to monitor/barge in other calls
using the feature codes for each spy mode, refer to 'Feature Codes' page for
more information.
www.yeastar.com
Page38
MyPBX U300 Administrator's Guide
·
spy modes
There are 4 spy modes available for choice:
General spy: you have the permission to use the following 3 modes.
Normal spy: you can only hear the call, but can't talk
Whisper spy: you can hear the call, and can talk with the monitored extension
Barge spy: you can hear the call and talk with them both
Note: for example,if 500 want to monitor extension 501, we need to enable the
'allow being spied ' for 501, and choose the spy mode for extension 500.
Then pick up 500 and dial “feature codes + 501” to start monitoring when 501
is in a call.
If 500 choose „normal spy‟, it should dial‟*90501‟ to start monitoring;
if 500 choose „whisper spy‟, it should dial „*91501‟ to start monitoring;
if 500 choose „barge spy‟, it should dial „*92501‟ to start monitor;
if 500 choose „general spy‟, it can dial „*90501‟,‟*91501‟ or „*92501‟ to start
monitor.
Figure 6-4
www.yeastar.com
Page39
MyPBX U300 Administrator's Guide
VoIP Extensions
A VOIP extension is a SIP/IAX Account that allows an IP Phone or an IP SoftPhone client to register on MyPBX
Figure 6-5
We can click „Add extension‟ to start.
Figure 6-6
1) General
·
Type
Extension type: SIP,IAX or SIP/IAX.
www.yeastar.com
Page40
MyPBX U300 Administrator's Guide
SIP – The extension sends and receives calls using the VoIP protocol SIP.
IAX -The extension sends and receives calls using the VoIP protocol IAX.
·
Extension
The numbered extension, i.e. 1234, that will be associated with this particular
User / Phone.
·
Password
The password for this extension, Ex: „12t3f6‟
·
Name
A character-based name for this user, EX: „Bob Jones‟
·
Caller ID
The Caller ID will be used when this user calls another internal extension.
2) Voicemail
·
Enable Voicemail
Check this box if the user should have a voicemail account.
·
Voicemail Access PIN #
The voicemail Password for this extension, i.e. „1234‟.
3) Mail Setting
This option defines whether or not voicemails or faxes are sent to an Email
Address as attachment.
·
Enable Send Voicemail
Once enabled, the voicemail will be sent to email as an attachment.
·
Email Address
Email address used to receive the voicemail or Fax.
Note: Please ensure that the section 'SMTP Settings For Voicemail'(in the
'Voicemail Settings') have been properly configured before using this feature.
4) Group
·
Pickup Group
If this extension belongs to a pickup group, any calls that ring this extension can
be picked up by other extensions in the same pickup group by dialing the Call
Pickup feature code (default is*4).
Note: *4 is the default setting, it can be changed under Feature Codes ->
General -> Call Pickup.
www.yeastar.com
Page41
MyPBX U300 Administrator's Guide
5) Call Duration Settings
Setup the max cull duration for every call of this extension, but it‟s only valid for
outbound calls. And if enter „0‟ or leave this blank empty, the value would be
equal to the max call duration configured in the Option Settings page.
Note: This setting will not be valid for internal calls.
6) VoIP Settings
·
NAT
This setting should be used when the system is using a public IP address to
communicate with devices hidden behind a NAT device (such as a broadband
router). If you have one-way audio problems, you usually have problems with
your NAT configuration or your firewall's support of SIP and/or RTP ports.
·
Qualify
Send check alive packets to IP phones
·
Enable SRTP
Enable extension for SRTP (RTP Encryption).
·
Transport
This will be the transport method used by the extension. The options are UDP
(default) or TCP or TLS.
·
DTMF Mode – RFC2833, Info, Inband, Auto.
·
Remote Register
Allow to register remote extensions.
This option is used to enhance the system security, it‟s disabled by default.
More details for the system security configuration please refer to APPENDIX G
MyPBX Security Configuration Guide.
7) Other Options
.Call Waiting
Check this option if the extension should have Call Waiting capability. If this
option is checked, the „When busy‟ follow me options will not be available. The
call waiting function of IP phone has higher priority than MyPBX‟s call waiting
function.
.DND
Don‟t Disturb. When DND is enabled for an extension, the extension will be not
available.
.User Web Interface
Check this option to allow the user to login to the MyPBX User Web interface,
www.yeastar.com
Page42
MyPBX U300 Administrator's Guide
which can be used to check voicemail and extension recordings. Users may login
to MyPBX User Web interface by using their extension number and voicemail PIN
# as the login and password respectively.
.Ring Out
Check this option if you want to customize the ring time. Ring tone will stop over
the time defined.
8) Follow me (Call Forwarding)
Call forwarding for an extension can be configured here. The administrator can
configure Follow Me option for this extension. If you want to transfer the call to
an outbound number, please follow the dial pattern of outbound route filled in
the outbound number.
For example: transferring to your mobile phone number 123456789, the dial
pattern of outbound route is „9.‟, you should fill in 9123456789 here.
9) IP Restriction
·
Enable IP Restriction
Check this option to enhance the VoIP security for MyPBX. If this option is
enabled, only the permitted IP/Subnet mask will be able to register this
extension number. In this way, the VoIP security will be enhanced.
·
Permitted ‘IP address/Subnet mask’
The input format should be „IP address‟+‟/‟+‟Subnet mask‟.
e.g."192.168.5.100/255.255.255.255" means only the device whose IP
address is 192.168.5.100 is allowed to register this extension number.
e.g."192.168.5.0/255.255.255.0" means only the device whose IP address is
192.168.5.XXX is allowed to register this extension number.
10) Mobility Extension
MyPBX allows you to use your mobile phone as extension. If you set your mobile
phone as mobility extension and then you call MyPBX with this mobility phone,
you will hear a dial tone. MyPBX will recognize your call as a call from an
extension. You can dial the number of other extensions (Your caller ID will be
the number of your extension) or dial out via outbound routes just like dialing
from your extension.
·
Mobility Extension Number
Don't forget to add the dial patterns of the outbound route at the beginning of
your mobile phone number when you fill in the mobility extension number filed.
E.g. if you want to set “15960XXXXXX” as mobile extension, and the dial pattern
of the outbound route is “9”; you should set “915960XXXXXX” here.
Note: If callback is enabled in the inbound route, the mobility extension
function of this inbound route will be disabled
www.yeastar.com
Page43
MyPBX U300 Administrator's Guide
11) Spy Settings
MyPBX allows extension to monitor/barge in other conversation. Once this
feature is enabled, the extension has the ability to monitor/barge in other calls
using the feature codes for each spy mode, refer to 'Feature Codes' page for
more information.
·
spy modes
There are 4 spy modes available for choice:
General spy: you have the permission to use the following 3 modes.
Normal spy: you can only hear the call, but can't talk
Whisper spy: you can hear the call, and can talk with the monitored extension
Barge spy: you can hear the call and talk with them both
Note: for example,if 500 want to monitor extension 501, we need to enable the
'allow being spied ' for 501, and choose the spy mode for extension 500.
Then pick up 500 and dial “feature codes + 501” to start monitoring when 501
is in a call
If 500 choose
If 500 choose
If 500 choose
If 500 choose
monitor.
„normal spy‟, it should dial‟*90501‟ to start monitoring;
„whisper spy‟, it should dial „*91501‟ to start monitoring;
„barge spy‟, it should dial „*92501‟ to start monitor;
„general spy‟, it can dial „*90501‟,‟*91501‟ or „*92501‟ to start
www.yeastar.com
Page44
MyPBX U300 Administrator's Guide
Figure 6-7
6.1.2 Phone Provisioning
The Auto Provision sub menu provides users a method to Auto Provision IP
Phone after the Express Setup process.
Note: Auto Provision functions fully test with these models:
Yealink (T12,T18,T20,T22,T26,T28,T32,T38,VP530,VP-2009)
Snom ( 300,320,360,370)
Polycom (IP 6000,IP 7000,IP 32X,IP33X,IP430,IP450,IP550,IP560,VVX1500)
Cisco (IP7940,IP7960)
Aastra(480i,480i CT,6757i,6757i CT, 6737i)
Grandstream(GXP1450,GXP2100,GXP2110,GXP2120)
Escene(ES220,ES320,ES330,ES410,ES620)
Fanvil(C56,C58,C60,C62)
News:
When provisioning Yealink and Snom IP phone, MyPBX is not needed to
be set as the only DHCP server any more
www.yeastar.com
Page45
MyPBX U300 Administrator's Guide
Figure 6-8
6.1.2.1 General Settings for Yealink
In this page, you can configure it before provisioning Yealink IP phones,
including the items like general preferences, codecs, remote phone book and
firmware upgrade
Note: if firmware download server is enabled, IP phone will update the firmware
automatically according the version and server you have configured during the
provision process.
Figure 6-9
www.yeastar.com
Page46
MyPBX U300 Administrator's Guide
6.1.2.2 General Settings for Aastra
In this page, you can configure it before provisioning Aastra IP phones,
including the items like local dial plan, time and date setting programkeys
configuration and so on.
Figure 6-10
6.1.2.3 Phone book
You can add your contacts here and provision them to your IP phone
Figure 6-11
1) Add Contact
·
Type
There are three types: None, VIP and Deny list (Blacklist).
·
Group
There are 5 groups: None, Friends, Family, Work, Colleagues list.
·
Nick Name
You can set a nick name for this number.
·
Favorite
Only works with snom phone.
www.yeastar.com
Page47
MyPBX U300 Administrator's Guide
·
Organization
Input the organization of this contact. Only works with snom phone.
·
Title
Input the title of this contact. Only works with snom phone.
·
Email
Input the email of this contact. Only works with snom phone.
·
Birthday
Input the birthday of this contact. Only works with snom phone.
·
First Name
Input the first name of this contact. Only works with snom phone.
·
Family Name
Input the family of this contact. Only works with snom phone.
·
Office Number
Input the office number here
·
Mobile Number
Input the mobile number here
·
Home Number
Input the home number here
·
Sub Number
Add sub number of this contact. Only works with snom phone.
·
Note
Take some note of this contact. Only works with snom phone.
www.yeastar.com
Page48
MyPBX U300 Administrator's Guide
Figure 6-12
2) Upload Phonebook
You can upload a phonebook before auto provision, which will be provisioned to
the IP phone when using auto provision feature to configure your IP phones. The
format of phonebook should be *.xml.
Note:All the existing phonebooks of the IP phone will be replaced automatically
if the phonebooks are configured in this way.
6.1.2.4 Configure phone
Let's take provisioning yealink as an example
Create New Phone have two modes,
Create New phone in webpage and Upload the IP Phone‟s configure file.
Add new phone via webpage
Click „Add Phone‟ and fill in the corresponding information in the popup window
www.yeastar.com
Page49
MyPBX U300 Administrator's Guide
Figure 6-13
1) General
·Enabled
Choose yes or no to enable or disable this extension
·NewConfig
If the firmware version number is greater than or equal to 70,please enable this
option.
Note: when choose the Manufacturer as Yealink, a special option „NewConfig‟
need to be considered. If the firmware version number of the Yealink phone is
bigger or equal to 70, please enable this option.
·MAC address
Input the MAC address of IP phone
·
Name
Put the name of this Phone here.
·
Manufacturer
You can choose the Manufacturer of IP phone
·
Phone Type
Choose the model of your phone. Only for snom phone
·
Call Waiting
This call feature allows your phone to accept other incoming calls to an
extension already in an active call.
www.yeastar.com
Page50
MyPBX U300 Administrator's Guide
·
Key as Send
Configure the key as send, you choose # ,* or disable it
·
Auto redial
Enable the auto redial for IP Phone
·
Auto answer
Configure if auto answer is allowed for IP phone
·
Phone book
Enable the feature of phone book of IP phone
2) Codecs
In this page, we can set the codecs for Ip phone
Figure 6-14
3) Line
In this page, we can set each line of IP phone for the account you want, active
or not .
www.yeastar.com
Page51
MyPBX U300 Administrator's Guide
Figure 6-15
Extension: Selected the extension number for IP Phone.
Label: It is shown on the LCD for users to identify the account.
Line Active: You can choose on/off to enable/disable the account respectively
4) Memory key settings
In this page, we can configure the DSS keys of IP phone one by one .
Figure 6-16
www.yeastar.com
Page52
MyPBX U300 Administrator's Guide
5) Line keys settings
We can configure the line key settings for this IP phone
Figure 6-17
6.1.2.5 Not configured phone
In this section, MyPBX will scan all the supported IP phones and display here, we
can click the 'MAC address' of IP phone and input the corresponding information
in the popup window, like the picture shows below
Figure 6-18
6.1.2.6 Upload a file
Click „Upload a file‟ and choose the configure file of IP phonein the popup
window.
Note: the file format must be .cfg
Please edit the configuration files in advance before uploading
Figure 6-19
www.yeastar.com
Page53
MyPBX U300 Administrator's Guide
6.2 Trunks
There are two types in MyPBX U300, the VOIP trunk and the E1 trunk, we cannot
any other trunks like PSTN/GSM/BRI anymore.
6.2.1 Physical Trunk
In this page we can configure the details of E1 trunk, before configure anything,
please make sure the cable is fine, and you have got enough information from
the ISDN provider.
Figure 6-19
On the Physical Trunk page, click „Edit‟ on the selected trunk and modify its
properties in the popup window:
www.yeastar.com
Page54
MyPBX U300 Administrator's Guide
Figure 6-20
·Trunk name
Set the trunk name
·
Signaling
PRI-NET, PRI-CPE,MFC/R2,SS7
·
Mode Type
E1 / T1 / J1
·
Switch Type
national: National ISDN type2 (common in the US)
ni1: National ISDN type 1
dms100: Nortel DMS100
4ess: AT&T 4ESS
5ess: Lucent 5ESS
euroisdn: EuroISDN
qsig: Minimalistic protocol to build a "network" with two or more PBX of different
www.yeastar.com
Page55
MyPBX U300 Administrator's Guide
vendors!
·
PRI Dial Plan
Sets an option required for some (rare) switches that require a dial plan
parameter to be passed. This option is ignored by most PRI switches. It may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged from the default.
·
Reset interval
Sets the time in seconds between restart of unused channels. Some PBXs don't
like channel restarts. so set the interval to a very long interval e.g. 100000000
or 'never' to disable *entirely*. If you are in Israel, the following is important:
As Bezeq in Israel doesn't like the B-Channel resets happening on the lines, it is
best to set the reset interval to 'never' when installing a box in Israel. Our past
experience also shows that this parameter may also cause issues on local
switches in the UK and China.
·
PRI Local Dial Plan
Sets an option required for some (rare) switches that require a dial plan
parameter to be passed. This option is ignored by most BRI switches. It may be
necessary on a few pieces of hardware. This option can almost always be left
unchanged from the default.
·
Over Lap Dial
Define whether MyPBX can dial this switch using overlap digits. If you need
Direct Dial-in (DDI; in German "Durchwahl") you should change this to yes, then
MyPBX will wait after the last digit it receives.
·
PRI Indication
Tells how Device should indicate Busy() and Congestion() to the switch/user.
Accepted values are:
inband: Device plays indication tones without answering; not available on all
PRI/BRI subscription lines .
outofband: Device disconnects with busy/congestion information code so the
switch will play the indication tones to the caller. Busy() will now do same as
setting PRI_CAUSE=17 and Hangup().
·
Facility Enable
To enable transmission of facility-based ISDN supplementary services (such as
caller name from CPE over facility).
·
NSF
Used with AT&T PRIs.If outbound calls are being rejected due to "Mandatory
information element missing" and the missing IE is 0x20, then you need this
www.yeastar.com
Page56
MyPBX U300 Administrator's Guide
setting.
·
CRC
CRC Verification.
·
Codec
Default ,A-Law,U-Law.
·
Echo Cancellation
Echo cancel Obviously this disables or enables echo cancellation, it is
recommended to not turn this off.
1) CallerID Prefix
·
International Prefix
When there are international calls coming in via this BRI trunk, the International
Prefix you have set here will be added before the CID. So you can know this is
an international call before you answer it.
·
National Prefix
When there are national calls coming in via this BRI trunk, the National Prefix
you have set here will be added before the CID. So you can know this is a
national call before you answer it.
·
Local Prefix
When there are Local calls coming in via this BRI trunk, the Local Prefix you have
set here will be added before the CID. So you can know this is a local call before
you answer it.
·
Private Prefix
When there are Private calls coming in via this BRI trunk, the Private Prefix you
have set here will be added before the CID. So you can know this is a Private call
before you answer it.
·
Unknown Prefix
When there are calls with unknown number coming via this BRI trunk, the
Unknown Prefix you set here will be shown as the caller ID.
2) DOD Setting
DOD (Direct Outward Dialing) means the caller ID displayed when dialing out,
before configure this, please make sure the provider supports this feature
·
Global DOD
Global direct outward dialing number.
www.yeastar.com
Page57
MyPBX U300 Administrator's Guide
·
DOD
Direct Outward Dialing Number.
·
Associated Extension
The extension make call out via BRI Trunk will display the associated DOD.
6.2.2 VoIP Trunk
There are two types of VOIP trunk in MyPBX: SIP and IAX, in this page, we can
also configure the „service provider‟ trunk, which doesn‟t need the use name
and password for authorization, when you have bought a trunk from provide
with IP address only, please choose „service provider‟ trunk .
Figure 6-21
6.2.2.1 VoIP Trunk
In this page, we can configure VoIP trunk (SIP/ IAX) you have got from provider
with the authorization name and password .
1)
Add SIP Trunk
Input correct SIP information (provide by VoIP provider). Inaccurate
information will prevent the trunk from registering.
www.yeastar.com
Page58
MyPBX U300 Administrator's Guide
Figure 6-22
·
Type
SIP – Identifies whether the trunk sends and receives calls using the VoIP
protocol SIP
·
Provider Name
A unique label to help you identify this trunk when listed in outbound rules,
incoming rules etc. Ex: 'yeastar'.
·
Hostname/IP
Service provider‟s hostname or IP address.5060 is the standard port number
used by SIP protocol. Don‟t change this part if it is not required.
.Domain
VoIP provider‟s server domain name .
·
Username
www.yeastar.com
Page59
MyPBX U300 Administrator's Guide
Username of SIP account. Used for SIP trunk registration.
.Authorization name
Used for SIP authentication. Leave this blank if not required.
·
Password
Password of SIP account .
.From User
All outgoing calls from this SIP Trunk will use the From User (In this case the
account name for SIP Registration) in From Header of the SIP Invite package.
Keep this field blank if not needed
.Online number
Define the online number that expected by „Skype Connect‟ and some other SIP
service providers. Leave this field blank if not needed.
·
Maximum Channels
Controls the maximum number of outbound channels (simultaneous calls) that
can be used on this trunk . Inbound calls are not counted against the maximum.
Set as 0 to specify no maximum.
·
Caller ID
Specify the caller ID to use when making outbound calls over this trunk. The
caller ID set in the „extension‟ screen will override the caller ID set in the „VOIP
trunk‟ screen. Please note that not all the service providers support this feature.
Contact your service provider for more information.
·
Outbound Proxy Server
A proxy that receives requests from a client, even though it may not be the
server resolved by the Request-URI.
·
Codecs
Define the codec for this sip trunk and its priority
Note: To change the codec type and priority of this trunk, please create it first,
it will appear when you edit it again.
·
Transport
This will be the transport method used by the SIP Trunk. This method is given by
the SIP trunk provider. The options are UDP (default) or TCP or TLS.
·
Enable SRTP
Define if SRTP is enabled for this trunk
www.yeastar.com
Page60
MyPBX U300 Administrator's Guide
·
Qualify
Send check alive packets to the sip provider.
·
DTMF mode
Set default mode for sending DTMF of this trunk. Default setting: rfc2833
·
DOD
DOD (Direct Outward Dialing) means the caller ID displayed when dialing out,
before configure this, please make sure the provider supports this feature
·
Associated Extension
The extension make call out via SIP Trunk will display the associated DOD
2) Add IAX trunk
Input correct IAX information (provided by VOIP provider). Inaccurate
information will prevent the trunk from registering.
Figure 6-23
·
Type
IAX – Identifies whether the trunk sends and receives calls by using the VoIP
protocol IAX.
·
Provider Name
A unique label to help you identify this trunk when listed in outbound rules,
incoming rules etc. Ex: 'yeastar2'.
www.yeastar.com
Page61
MyPBX U300 Administrator's Guide
·
Hostname/IP
Service provider‟s hostname or IP address. 4569 is the standard port number
used by IAX protocol. Don‟t change this part if it is not required.
·
Username
Username of IAX account. Used for IAX trunk registration.
·
Password
Password of IAX account .
.Online number
Define the online number that expected by „Skype Connect‟ and some other SIP
service providers. Leave this field blank if it's no required.
·
Maximum Channels
Controls the maximum number of outbound channels (simultaneous calls) that
can be used on this trunk . Inbound calls are not counted against the maximum.
Set as 0 to specify no maximum.
·
Caller ID
Specify the caller ID to use when making outbound calls over this trunk. The
caller ID set in the „extension‟ screen will override the caller ID setting in the
„VOIP trunk‟ screen. Please note that not all the service providers support this
feature. Contact your service provider for more information.
·
DOD
DOD (Direct Outward Dialing) means the caller ID displayed when dialing out,
before configure this, please make sure the provider supports this feature
·
Associated Extension
The extension make call out via IAX Trunk will display the associated DOD
6.2.2.2 Service Provider
This is service provider trunk (peer to peer mode), which authorized using IP
address only. If you have got a trunk with IP address only, please choose this
type
www.yeastar.com
Page62
MyPBX U300 Administrator's Guide
Figure 6-24
·
Type
SIP or IAX
SIP – Identifies whether the trunk sends and receives calls by using the VoIP
protocol SIP.
IAX - Identifies whether the trunk sends and receives calls by using the VoIP
protocol IAX.
·
Provider Name
A unique label would help to you identify this trunk. Ex: 'Provider2'.
·
Hostname/IP
Service provider‟s hostname or IP address.
Note: 5060 is the standard port number used by SIP protocol, 4569is the
standard port number used by IAX protocol. Don‟t change this part if it is not
required.
·
Maximum Channels
Controls the maximum number of outbound channels (simultaneous calls) that
can be used on this trunk. Inbound calls are not counted against the maximum.
Leave blank to specify no maximum.
·
Codecs
Define the codec for this sip trunk and its priority
www.yeastar.com
Page63
MyPBX U300 Administrator's Guide
Note: codec can only display when edit it after creating the trunk.
·
Transport
This will be the transport method used by the SIP Trunk. This method is given by
the SIP trunk provider. The options are UDP (default) or TCP or TLS.
·
Qualify
Send check alive packets to the sip provider.
·
DTMF mode
Set default mode for sending DTMF of this trunk. Default setting: rfc2833
·
DOD
DOD (Direct Outward Dialing) means the caller ID displayed when dialing out,
before configure this, please make sure the provider supports this feature
·
Associated Extension
The extension make call out via this Trunk will display the associated DOD.
6.3 Outbound Call Control
6.3.1 Outbound Routes
In this page, we can configure the outbound rules to control the outgoing calls.
Note:
1. The max number of outbound route is 64
2. If the dial patterns are the same in several routes, MyPBX will choose the
available routes from top to the last one.
3. When you have created a new extension, please edit the outbound route so
that he can dial out too
Figure 6-25
We can create outbound route or use the default route „pstnout‟ ( dial
9+numbers to dial out)
www.yeastar.com
Page64
MyPBX U300 Administrator's Guide
Figure 6-26
·
Route Name
Name of this Outbound Route. Ex: 'Local' or 'Long Distance' etc.
·
Dial Pattern
Outbound calls that match this dial pattern will use this outbound route. There
are a number of dial pattern characters that have special meanings:
X: Any Digit from 0-9
Z: Any Digit from 1-9
N: Any Digit from 2-9
[12345-9]: Any digit in the brackets (in this example, 1, 2, 3, 4, 5, 6, 7, 8, 9)
The „.‟ Character will match any remaining digits. For example, 9011. will match
any phone number that starts with 9011, excluding 9011 itself.
The „!‟ will match none remaining digits, and causes the matching process to
complete as soon as it can be determined that no other matches are possible.
Example 1: NXXXXXX will match any 7 digits phone number.
www.yeastar.com
Page65
MyPBX U300 Administrator's Guide
Example 2: 1NXXNXXXXX will match a phone number starting with a 1,
followed by a 3-digit area code, and then 6 digit number.
·
Strip digits from front
Allows the user to specify the number of digits that will be stripped from the
front of the phone number before the call is placed. For example, if users must
press 0 before dialing a phone number, one digit should be stripped from the
dial string before the call is placed.
·
Prepend these digits before dialing
These digits will be prepended to the phone number before the call is placed. For
example, if a trunk requires 10 digit dialing, but users are more comfortable
with 7 digit dialing, this field could be used to prepend a 3 digit area code to all
7 digit phone numbers before calls are placed.
·
Password
The route password can be used to protect this route from being accessed
without a password.
·
T.38 Support:
Enable T38 fax in this outbound route(Only for SIP Trunk).
·
Rrmemory Hunt
Round robin with memory, remembers which trunk was used last time, and then
use the next available trunk to call out.
·
Member Extensions
Defines the extensions that will be permitted to use this outbound route.
·
Member Trunks
Defines the trunks that can be used for this outbound route.
6.3.2Speed Dial Settings
Figure 6-26
www.yeastar.com
Page66
MyPBX U300 Administrator's Guide
1) Options
·
The prefix of speed dial
The prefix should be dialed before the speed dial number. Default is *99
Figure 6-27
2) Add new speed dial.
·
Source Number
The speed dial number.
·
Destination Number
The number you want to call.
e.g. The source number is ”123”. The destination number is 5503305.The prefix
number is *99.You can use an extension with any type to dial *99123, then it
will call to number 5503305.
Note: Don‟t forget to add the outbound dial prefix if you would like to dial the
speed dial number through trunk.
6.4 Inbound Call Control
In this page, we can configure the details of IVR, ring group, queue and inbound
routes.
6.4.1 IVR
When there‟s an inbound call aims at Auto Attendant, MyPBX will play an IVR
recording and route the caller to the requested destination (for example,
„Welcome to XX company, for sales press 1, for technical support press 2, for
operator press 0, etc‟). The system will transfer the call to corresponding
extension according to DTMF digits inputted by the user
Figure 6-28
www.yeastar.com
Page67
MyPBX U300 Administrator's Guide
There is a default IVR here, we can edit it directly or add IVR by yourself
Figure 6-29
·
Number
MyPBX treats IVR as an extension; you can dial this extension number to reach
the IVR from internal extension.
·
Name
A name for the IVR
·
Prompt
The prompt recording that will be played when this IVR is reached.
·
Repeat Count
The number of times that the selected IVR prompt will be played.
·
Key Timeout
Wait for the user to enter a new extension for a specified number of seconds.
www.yeastar.com
Page68
MyPBX U300 Administrator's Guide
·
Enable Direct Dial
Allow the caller to dial other extensions number directly.
·
Key Press Events
A list of actions that can be performed depending on the digit dialed by the user.
·
Key
The Key pressed when the callers hear the IVR prompt.
·
Action
When the callers press the corresponding key, the action MyPBX executes.
No Action: Do nothing
Connect to Extension: Connect the call to an extension.
Connect to Voicemail: Connect the call to the voicemail of an extension
Connect to RingGroup: Connect the call to a ringgroup.
Connect to IVR: Connect the call to an IVR.
Connnect to Conference Room: Connect the call to a conference room.
Connect to DISA: Connect the call to a DISA.
Connect to Queue: Connect the call to a queue.
Connect to Faxes: Connect the call to Faxes of extensions.
Dial by Name:The callers can dial the name of an extension to connect to the
corresponding extension.
Hung up: Hung up the call.
·
Destination
Where will MyPBX route the call when the action occurs.
·
Time Out
Defines the timeout action. A timeout occurs after the IVR prompt has finished
playing for the number of times specified by the 'Repeat Count' field.
·
Invalid
Defines the invalid action. The invalid action is triggered if the user enters a
DTMF digit that is not defined for this IVR.
www.yeastar.com
Page69
MyPBX U300 Administrator's Guide
6.4.2 Ring Groups
Ring groups can be configured to balance the call traffic for multiple users and
give callers a higher level of availability for incoming calls. Multiple ring methods
and voicemail are supported.
Note: follow me feature in extension page will not take effect when it‟s ringing
as an agent
Figure 6-30
There is a default ringgroup, you can edit it or create a new one
Figure 6-31
·
Ring Group Name
This option defines a name for this group, i.e. „Sales‟. „Ring Group Name‟ is a
label to help you identify this group in the group list.
·
Ring Group Number
This option defines the numbered extension that can be dialed to reach this
group.
www.yeastar.com
Page70
MyPBX U300 Administrator's Guide
·
Strategy
This option sets the Ringing Strategy for this Group. The options are as follows:
1. RingAll Simultaneously: Ring all available Extensions simultaneously.
2. Ring Sequentially: Ring each extension in the group one at a time.
·
Seconds to ring each member
1. If the strategy is „Ring All Simultaneously‟, it means set the number of
seconds to ring this group before routing the call according to the „Destination if
No Answer‟ settings.
2. If the strategy is „Ring Sequentially‟, it means set the number of seconds to
ring a single extension before moving onto the next one.
·Ring Group Members
An extension can be made a member of this ring group by moving it into the
„Selected‟ box.
·
Destination If No Answer
When all members on this group fail to answer the call, system will handle the
call according to the selected destination.
6.4.3 Queues
Call Queues give users (i.e. call centers) an efficient means to have their calls
answered in the order they were received to deliver top tier customer service.
Figure 6-32
Call queues allow calls to be sequenced to one or more agents.
Note:
1. Dial 'Queue number + '*'' to log in or 'Queue number + '**'' to log out the
queue. For example, if the queue number is '680', then agent can dial '680*'
to log in or '680**' to log out.
2. Follow me feature in extension page will not take effect when it‟s ringing as
an agent of queue
www.yeastar.com
Page71
MyPBX U300 Administrator's Guide
Figure 6-33
·
Queue Name
A name for the Queue.
·
Queue Number
www.yeastar.com
Page72
MyPBX U300 Administrator's Guide
Use this number to dial into the queue, or transfer callers to this number to put
them into the queue.
·
Queue Password
You can require agents to enter a password before they can login to this queue.
This field allowed to be blank empty, it means the agents can login to this queue
without password.
·
Queue Agent Timeout
The number of seconds an agent's phone can ring before we consider it a
timeout.
·
Queue Max Wait Time
The maximum number of seconds a caller can wait in a queue before being
pulled out. (0 for unlimited).
·
Queue Ring Strategy
This option sets the Ringing Strategy for this Queue. The options are
RingAll: Ring All available Agents simultaneously until one answers.
LeastRecent: Ring the Agent which was least recently called.
FewestCalls: Ring the Agent with the fewest completed calls.
Random: Ring a Random Agent.
RRmemory: Round Robin with Memory, Remembers where it left off in the last
ring pass".
1) Agents
This selection shows all users. Selecting a user here makes them a agent of the
current queue.
2) Caller Position Announcements
·
Announce Position
Announce position of caller in the queue
·
Announce Hold Time
Enabling this option causes MyPBX to announce the hold time to the caller
periodically based on the frequency timer. Either yes or no; hold time will not be
announced if <1 minute.
·
Frequency
How often to announce queue position and estimated hold time.
Note: '0 seconds' means disable the announcement
3) Periodic Announcements
·
Prompt
www.yeastar.com
Page73
MyPBX U300 Administrator's Guide
Select a prompt file to play periodically.
·
Frequency
How often to announce a prompt to the caller.
4) Events
If a caller presses the key while waiting in the queue, this setting selects which
action should process the key press.
5) Failover-Destination
Define the failover action. A failover occurs after the user reach the Queue max
wait time.
6) Others
·
Music On Hold
Select the 'Music on Hold' Class for this Queue.
·
Leave When Empty
This option controls whether callers already on hold are forced out of a queue
that has no agents. There are two options.
Yes: Callers are forced out of a queue when no agents are logged in.
No: Callers will remain in a queue with no agents.
·
Join Empty
This option controls whether callers can join a call queue that has no agents.
There are two options,
Yes: Callers can join a call queue with no agents or only unavailable agents
No: Callers cannot join a queue with no agents
The default option is No.
·
Agent Announcement
Announcement played to the Agent prior to bridging in the caller.
·
Join Announcement
Announcement played to callers once prior to joining the queue.
·
Retry
The number of seconds we wait before trying all the phones again.
·
Wrap-up time
How many seconds after the completion of a call an Agent will have before the
Queue can ring them with a new call. The default is 30.
www.yeastar.com
Page74
MyPBX U300 Administrator's Guide
6.4.4 Conferences
Figure 6-34
Conference Calls increase employee efficiency and productivity, and provide a
more cost-effective way to hold meetings. Conference agents can dial * to
access to the settings options and the admin can kick the last user out and can
lock the conference room.
·
Extension
This is the number dialed to reach this Conference Room.
·
Admin
Admin can kick a user out and can lock the conference room.
·
Pin #
Set a PIN # that must be entered in order to access this conference room (i.e.
1234).
Figure 6-35
6.4.5 Inbound Routes
Inbound routing processes incoming call traffic to destination extensions during
office hours or outside office hours
www.yeastar.com
Page75
MyPBX U300 Administrator's Guide
Figure 6-36
There is a default inbound route for all the trunks and set IVR as the destination,
you can edit it or create a new one for your demands. When an incoming call
arrives, the system will first check „fax detection‟, then „Holidays‟, at last
„Business Days‟.
figure 6-37
1)
General
·
Route Name
A name for this inbound route. Ex: 'pstnin' etc.
·
DID Number
www.yeastar.com
Page76
MyPBX U300 Administrator's Guide
Define the expected DID Number if this trunk passes DID on incoming calls.
Leave this field blank to match calls with any or no DID info. You can also use
pattern matching to match a range of numbers. The following patterns may be
used:
X: Any Digit from 0-9
Z: Any Digit from 1-9
N: Any Digit from 2-9
[12345-9]: Any digit in the brackets (in this example, 1,2,3,4,5,6,7,8,9)
The „.‟Character will match any remaining digits. For example, 9011. will match
any phone number that starts with 9011, excluding 9011 itself.
The „!‟ will match none remaining digits, and causes the matching process to
complete as soon as it can be determined that no other matches are possible.
Example 1: NXXXXXXwill match any 7 digits phone number.
Example 2: 1NXXNXXXXXwill match a phone number starting with a 1,
followed by a 3-digit area code, and then 6 digit number.
For more information, please refer to Appendix G How to Use DID.
·
Extension
Define the extension for DID number. This field is only valid when you use BRI,
SIP, SPS or SPX trunk for this inbound router. You can only input number and
„-„in this field, and the format can be xxx or xxx-xxx. The count of the number
must be only one or equal the count of the DID number.
·
Caller ID Number
Define the Caller ID Number to be matched on incoming calls. Leave this field
blank to match any or no DID info.
You can also use a pattern match (e.g. 2[345]X) to match a range of numbers.
The following patterns may be used:
X: Any Digit from 0-9
Z: Any Digit from 1-9
N: Any Digit from 2-9
[12345-9]: Any digit in the brackets (in this example, 1,2,3,4,5,6,7,8,9)
The „.‟Character will match any remaining digits. For example, 9011. will match
any phone number that starts with 9011, excluding 9011 itself.
The „!‟ will match none remaining digits, and causes the matching process to
complete as soon as it can be determined that no other matches are possible.
Example 1: NXXXXXXwill match any 7 digits phone number.
Example 2: 1NXXNXXXXXwill match a phone number starting with a 1,
followed by a 3-digit area code, and then 6 digit number.
·
Distinctive Ringtone
www.yeastar.com
Page77
MyPBX U300 Administrator's Guide
MyPBX support mapping to custom ring tone files. For example, if you configure
the distinctive ringing for custom ring tone to „Family‟, the ring tone will be
played if the phone receives the incoming call. This feature works with all IP
phones which support distinctive ringtone.
How do I configure distinctive ring tones? Please refer to APPENDIX E.
Note: If you want to use feature Distinctive ringtone, please confirm you‟re
your IP phone support this feature firstly. Currently distinctive ringtone can be
compatible with Yealink and Snom phone.
·
Enable Callback
You can enable the callback function of this inbound route. If you want to
configure the callback function, please refer to chapter 3.5.12
2)
Member Trunks
This area allows you to select which trunks will be member trunks for this route.
To make a trunk a member of this route, please move it to the 'Selected' box.
3)
Business Days
Define where the calls will be routed during Business Days.
·
Office Hours
Select one defined business days office hours.
·
Office Hours Destination
Configure where to route the incoming calls during office hours.
·
End Calls
Route the incoming calls to end calls, System will auto hang-up the call.
·
Extension
Route the incoming calls to a specific extension.
·
Voicemail
Route the incoming calls to extension‟s voicemail.
·
IVR
Route the incoming calls to a specific IVR.
·
Ring Group
Route the incoming calls to a specific Ring Group.
·
Conference Room
Route the incoming calls to a specific Conference Room.
www.yeastar.com
Page78
MyPBX U300 Administrator's Guide
·
DISA
Route the incoming calls to a specific DISA.
·
Queues
Route the incoming calls to a specific Queue.
·
Faxes
Route the incoming faxes to a specific extension‟s mail address.
Note: This function only supports T.38 faxes.
·
Outbound Routes
Route the incoming calls to a specific outbound route.
This function is mainly used for the connection of two branches.
For example: Company A locates headquarters in the USA with a branch B in
China. A and B both have MyPBX phone systems.
Now if staff of A would like to make a call to a telephone or mobile phone in
China from the extension of A but via the FXS line of B, that can be done by this
configuration.
·
Non-office Hours Destination
Configure where to route the incoming calls during non-office hours.
4)
During Holidays
Define where the calls will be routed during Holidays.
·
Holiday
Select the defined Holiday to use. When a time is defined in both Business Days
and Holidays, it will be treated as Holidays.
·
Destination
Configure where to route the incoming calls during holidays.
5)
Fax Detection
Configure if detecting faxes in this inbound route.
Note: Please choose IVR as the destination above before configure fax
detection (recommend)
·
Destination
Configure where the faxes will be routed when faxes are detected.
·
No detect
Do not detect faxes.
www.yeastar.com
Page79
MyPBX U300 Administrator's Guide
·
Custom Email
Customize an E-mail address to receive the faxes. You should first configure the
„Voicemail Settings->SMTP Settings for Voicemail‟ correctly before you use this
option.
·
Faxes
Send faxes to an extension. If choosing a FXS extension here, the fax will be
sent to the FXS port selected, you should connect a fax machine to this FXS port.
If Choosing a VoIP extension, the fax will be sent to the extension‟s voicemail as
an attachment.
Note: If you receive faxes with custom Email address, the „SMTP settings‟ of
„Voicemail Settings‟ should be configured successfully in advance. If you receive
faxes with E-mail address configured in VOIP extension voicemail, you should
first make sure the tested email to your email address works fine.
6.5 Audio Settings
It‟s allowed to customize the prompts in MyPBX, including the Audio In and
change the system prompts to your local country.
6.5.1 Custom Prompts
We can record or upload the prompts in this page, you can also play it directly to
confirm if it‟s a valid one, you can also download it and save it as an backup
Figure 6-38
1. Record new Prompt
Figure 6-39
www.yeastar.com
Page80
MyPBX U300 Administrator's Guide
The administrator can use this screen to record custom prompts by doing the
following:
1)Click „Record New Custom Prompt‟
2) Input the desired file name on the popup window and choose an extension to
call for recording (such as 500).
3) Click „Record‟. The selected extension will ring and you can pick up the phone
to start recording.
2. Upload Prompt
Figure 6-40
The administrator can also upload prompts by doing the following:
1))Click „Upload Prompt‟.
2) Click „Browse‟ to choose the desired prompt.
3) Click „Upload‟ to upload the selected prompt.
Note: The file size must not be larger than 1.8MB, and the file must be WAV
format:
GSM 6.10 8kHz, Mono, 1Kb/s;
Alaw/Ulaw 8kHz, Mono, 1Kb/s;
PCM 8kHz, Mono, 16Kb/s.
6.5.2 Music on Hold Prompts
In this page, we can upload the music on hold prompts or adjust the volume
from Audio In interface (Only available in MyPBX U300)
Figure 6-41
The administrator can upload on hold music as follows:
1) Click „Upload Music on Prompt ‟
2) Click „Browse‟ to choose the desired audio file.
3) Click „Upload‟ to upload the selected file.
www.yeastar.com
Page81
MyPBX U300 Administrator's Guide
Figure 6-42
Note: The sound file format should be as follows:
GSM 6.10, 8.000kHz, Mono, 1kb/sec;
Alaw/Ulaw 8.000kHz, Mono, 1kb/sec;
PCM 8.000kHz, Mono, 16kb/sec.
The file size must not be greater than 1.8MB.
6.5.3 System Prompts Settings
MyPBX have prompts of many languages. You can download the appropriate
language you need. MyPBX can support American English, Australian English,
Chinese, Dutch, French, Canadian French, German, Greek, Hungarian, Italian,
Polish, Portuguese, Brazilian Portuguese, Russian, Spanish, Mexican Spanish,
Turkish, Thai, Korean, Danish, Finnish, Norwegian, Swedish, Arabic, British
currently.
Note:
1. Auto-detection is highly recommended. But if you prefer to download via
HTTP or TFTP server, please contact the local dealer for the prompts
2. When update successfully, just click „apply the changes‟ on web then it will
take effect, there is no need to reboot.
Figure 6-43
6.6 Basic Settings
There are some basic settings we need to configure MyPBX U300,like the
www.yeastar.com
Page82
MyPBX U300 Administrator's Guide
general preferences, business hours, feature codes, voicemail settings
6.6.1 General Preferences
In this page, there are some general settings of MyPBX
Figure 6-44
1) General
·
Ring Timeout
Number of seconds to ring a device before handling the call as per the
extension‟s Follow Me settings . Default value is 30s.
.MAX call duration
The absolute maximum amount of time permitted for a call. A setting of 0
disables the timeout. Default value is 6000s.
.Maximum concurrent calls
Maximum concurrent calls limits. Default value 0 means no limit
·
Music on hold
Used to set hold music for the system.
Note: if you need use the „live music‟ from „Audio In‟ interface, please choose
„ external music‟ here.
www.yeastar.com
Page83
MyPBX U300 Administrator's Guide
·
Tone Region
Please select your country or nearest neighboring country to enable the default
dial tone, busy tone, and ring tone for your region.
Note: please reboot the system to take it effect.
·
HTTP bind port/Web Access Port
Port to use for HTTP sessions. Default: 80
Note: please reboot the system to take it effect.
·Distinctive Caller ID
When incoming calls are routed from ring group/queue/IVR, the caller ID
displays with the name of ring group/queue/IVR , for example
5503302(ringgroup_default)
Note: To display IVR's name, please press the key instead of the extension
number directly.
·
Follow Me Prompt
Configure whether to play a prompt „please wait while trying to look at the
person you are calling‟ when transfer a call by follow me settings.
·
Music on hold for Follow Me
Choose to play default music-on-hold, ringing tone or stay mute while „Follow
Me‟.
·
Invalid Phone Number Prompt
Configure the prompt when the dialed phone number is invalid.
·
Busy Line Prompt
Configure the prompt when the dialed phone number is busy.
·
Dial Failure Prompt
Configure the prompt when dial failed due to conjunction no-available channel.
2) Extension Preferences
·
User Extensions
The default value is 500 to 616
·
Ring Group Extensions
The default value is 620 to 629
·
Paging Group Extensions
The default value is 630 to 639
www.yeastar.com
Page84
MyPBX U300 Administrator's Guide
·
Conference Extensions
The default value is 640 to 659
·
IVR Extensions
The default value is 660 to 679
·
Queue Extensions
The default value is 680 to 689
6.6.2 Business Hours
Business hours including „holiday configuration‟ is used to control the incoming
calls, we can configure it in this page.
Figure 6-45
1) General
·
Enable Business Hours
·
disable Business Hours
2) Others
·
Enable Office Closed Timing
By dialing *81 (*81 is default) on an extension will force the office time closed
for the device whatever the general setting is.
·
Enable Office Timing
By dialing *82 (*82 is default) on an extension will force the office time enalbed
for the device whatever the general setting is.
·
Disable Office closed timing
By dialing *081 (*081 is default) on an extension will disable the Office Closed
www.yeastar.com
Page85
MyPBX U300 Administrator's Guide
Timing.
3) Add office hours
You can setup the business hours here.
4) Add Holiday
You can setup the holidays here.
If a time period is configured as both Holidays and office hours, it will be treated
as Holidays.
6.6.3 Feature Codes
There are many feature codes available in MyPBX, which allow users to dial from
extension side to realize the exact feature
Figure 6-46
1) General
·
One Touch Record
A user may initiateor stop call recording by dialing *1during a call. (*1 is default
setting)
·
Extension for Checking Voicemail
Users can check their Voicemail by dialing *2 on their phone (*2 is default
setting).
·
Voicemail for Extension
Users can leave a voicemail to other extensions by dialing # on their phone or
www.yeastar.com
Page86
MyPBX U300 Administrator's Guide
the incoming call could be forwarded to an extension‟s voicemail directly. (# is
default setting).
For example, extension 500 want to leave a message for extension 501, users
can use 500 dial‟#501‟ to enter the voicemail of 501.
·
Voicemail main menu
Users can go to the main menu by dialing *02 (*02 is default setting).
·
Attended Transfer
Users may transfer an incoming call by dialing *3 on their phone (*3 is default
setting).
·
Attended Transfer Timeout
The time out of transferring a call
·
Blind Transfer
Users may blind transfer an incoming call by dialing*03 on their phone (*03 is
default setting).
·
Call Pickup
Users may pick up an incoming call by dialing *4 on their phone (*4 is default
setting)
·
Extension Pickup
Users may pick up a specific extension‟s incoming call by dialing *04+extension
number on their phone (*04 is default setting)
·
Intercom
Define the feature code that is used to dial an extension in intercom mode. For
instance setting this value to *5 would allow you to initiate an intercom call with
extension 501 by dialing *5501.
·
Normal Spy
In this mode, you can only listen to the extension being spied, for example you
can dial *90501 to monitor extension 501
·
Whisper Spy
In this mode you can listen/whisper to the extension being spied, for example,
dialing *91501 to listen to extension 501, you can also talk with 501 too.
·
Barge Spy
In this mode, you can barge in both extensions involved the call, for example
dialing *92501 to barge in and talk with all the extensions inside
www.yeastar.com
Page87
MyPBX U300 Administrator's Guide
2) Call Park Preferences
·
Call Parking
User may park an incoming call on his own telephone by pressing „*6‟(*6 is
default setting)
·
Extension range used to park calls
User may park an incoming call on a designated extension at first and then pick
up the call again on any other extension.
·
Number of seconds a call can be parked before it is recalled.
Defines the number of seconds that a call can be parked before it is recalled to
the station that parked it.
3) Call Forwarding Preferences
·
Reset to Defaults
Users may reset all call forward defaults by calling *70 on their phone (*70 is
default setting).
Note: When reset to defaults. The call forwarding settings will be configured as
follows:
Always forward: Disabled
Busy forward to Voicemail: Enabled
No answer forward to Voicemail: Enabled
Do not disturb: Disabled
·
Enable Forward All Calls
Users may enable always forward by calling *71 on their phone (*71 is default
setting)
·
Disable Forward All Calls
Users may disable always forward by calling *071 on their phone (*071 is
default setting)
·
Enable Forward When Busy
Users may enable busy forward by dialing *72 on their phone (*72 is default
setting)
·
Disable Forward When Busy
Users may disable busy forward by calling *072 on their phone (*072 is default
setting)
·
Enable Forward No Answer
Users may enable no answer forward by calling *73 on their phone (*73 is
default setting)
www.yeastar.com
Page88
MyPBX U300 Administrator's Guide
·
Disable Forward No Answer
Users may disable no answer forward by calling *073 on their phone (*072 is
default setting)
·
Forward to number
Users may activate call forwarding by dialing this feature code, followed by the
extension or phone number to forward all calls to.
Note: Users may activate Forward to number by dialing *74 + phone number.
e.g.: by dialing *74501, all calls will be forwarded to extension 501.
·
Forward to Voicemail
Users may forward the call to Voicemail by calling *074 on their phone (*074 is
default setting)
·
Enable Do Not Disturb
Users may enable do not disturb by calling *75 on their phone (*75 is default
setting)
·
Disable Do Not Disturb
Users may disable do not disturb by calling *075 on their phone (*075 is default
setting)
6.6.4 Voicemail Settings
In this page, we can configure some settings for voicemail feature, including
general voicemail settings and SMTP settings, which is used for „voicemail to
email‟
Figure 6-47
www.yeastar.com
Page89
MyPBX U300 Administrator's Guide
1) General Voicemail Settings
a) Message Options
·
Max Messages per Folder
Set the maximum number of messages that can be stored in a single voicemail
box.
·
Max Message Time
Set the maximum length of a single voicemail message.
·
Min Message Time
Set the minimum length of a single voicemail message. Messages below this
threshold will be automatically deleted.
·
Ask Caller to Dial 5
If this option is set, the caller will be prompted to press 5 before leaving a
message.
·
Operator Breakout from Voicemail
If this option is set, the caller can jump out of the voicemail and go to the
destination (IVR) you set by dialing “0”.
b) Greeting Settings
·
Busy Prompt
Greeting played when the extension called is busy.
Skip greeting: Do not play a greeting.
Play busy greeting: play the extension busy greeting.
·
Unavailable Prompt
Greeting played when the extension called is Unavailable.
Skip greeting: Do not play a greeting.
Play Unavailable greeting: play the extension Unavailable greeting.
·
Leave a Message Prompt
Greeting played to ask the caller to dial 5 to leave a message.
Skip greeting: Do not play a greeting.
Play busy greeting: play the extension busy greeting.
Play Unavailable greeting: play the extension Unavailable greeting.
c) Playback Options
·
Announce Message Caller ID
If this option is enabled, the Caller ID of the party that left the message will be
played back before the voicemail message begins playing.
www.yeastar.com
Page90
MyPBX U300 Administrator's Guide
·
Announce Message Duration
If this option is set, the duration of the message in minutes will be played back
before the voicemail message begins playing.
.Announce Message Arrival Time
If this option is set, the arrival time of the message will be played back before
the voicemail message begins playing.
.Allow Users to Review Messages
Allow callers to review their recorded message before sending it to voicemail.
2) SMTP Settings for Voicemail
Note: If you want to send voicemail messages as email attachments, please
configure this section.
Figure 6-48
·
E-mail Address
The E-mail Address that MyPBX will use to send voicemail.
·
Password
The password for the email address used above
·
SMTP Server
The IP address or hostname of an SMTP server that the MyPBX will connect to in
order to send voicemail messages via email, i.e. mail.yourcompany.com.
·
Port
SMTP Port: the default value is 25.
·
Use SSL/TLS to send secure message to server
If the server of sending email needs to authenticate the sender, you need to
select the check box.
Note: Must be selected for Gmail or exchange server.
After filling out the above information, you can click on the „Test Account
Settings‟ button to check whether the setup is OK.
1) If the test is successful, you can use the email safely.
www.yeastar.com
Page91
MyPBX U300 Administrator's Guide
2) If test failed, please check the above information is correct or network is
proper.
6.7 Advanced Settings
6.7.1 SIP Settings
Figure 6-49
1) General
·
UDP Port
Port use for sip registrations, Default is 5060.
·
TCP Port
Port use for sip registrations, Default is 5060.
·
TLS Port
Port use for sip registrations, Default is 5061.
·
RTP Port Start
Beginning of RTP port range
·
RTP Port End
End of RTP port range
www.yeastar.com
Page92
MyPBX U300 Administrator's Guide
·
DTMF Mode
Set default mode for sending DTMF. Default setting: rfc2833
·
Max Registration/Subscription Time
Maximum duration (in seconds) of a SIP registration. Default is 3600 seconds.
·
Min Registration/Subscription Time
Minimum duration (in seconds) of a SIP registration. Default is 60seconds.
·
Default Incoming/Outgoing Registration Time
Default Incoming/Outgoing Registration Time: Default duration (in seconds)
of incoming/outgoing registration.
·
Register Attempts
The number of SIP REGISTER messages to send to a SIP Registrar before giving
up. Default is 8 times.
·
Register Timeout
Number of seconds to wait for a response from a SIP Registrar before timed out .
Default is 20 seconds.
·
Calling Channel Codec Priority
Once enabled, when dialing out via SIP/SPS trunks, the codec of calling channel
will be selected in preference. If not, MyPBX will follow the priority in your
SIP/SPS trunks.
·
Video Support
Support for SIP video or no. Default is yes.
·
Max Bit Rate
Configure the max bit rate for video stream. The default: 384kb/s
·
DNS SRV Look Up
Please enable this option when your SIP trunk contains more than one IP
address.
·
User Agent
To change the user agent parameter of asterisk, the default is „MyPBX‟, you
should change it if needed.
www.yeastar.com
Page93
MyPBX U300 Administrator's Guide
Figure 6-50
2) NAT
Note: Configuration of this section is only required when using remote
extensions.
·
Enable STUN
STUN (Simple Traversal of UDP through NATs) is a protocol for assisting devices
behind a NAT firewall or router with their packet routing.
·
STUN Address
The STUN server allows clients to find out their public address, the type of NAT
they are behind and the internet side port associated by the NAT with a
particular local port. This information is used to set up UDP communication
between the client and the VOIP provider and so establish a call.
·
External IP Address
The IP address that will be associated with outbound SIP messages if the system
is in a NAT environment.
·
External Host
Alternatively you can specify an external host, and the system will perform DNS
queries periodically.
This setting is only required when your public IP address is not static. It is
recommended that a static public IP address be used with this system. Please
contact your ISP for more information.
·
External Refresh Interval
If an external host has been supplied, you may specify how often the system will
perform a DNS query on this host. This value is specified in seconds.
·
Local Network Identification
www.yeastar.com
Page94
MyPBX U300 Administrator's Guide
Used to identify the local network using a network number/subnet mask pair
when the system is behind a NAT or firewall.
Some examples of this are as follows:
'192.168.0.0/255.255.0.0' : All RFC 1918 addresses are local networks;
'10.0.0.0/255.0.0.0' : Also RFC1918;
'172.16.0.0/12':AnotherRFC1918withCIDRnotation;
'169.254.0.0/255.255.0.0' : Zero conf local network.
Please refer to RFC1918 for more information.
·
NAT Mode
Global NAT configuration for the system. The options for this setting are as
follows:
Yes = Use NAT. Ignore address information in the SIP/SDP headers and reply to
the sender's IP address/port.
No = Use NAT mode only according to RFC3581.
Never = Never attempt NAT mode or RFC3581 support.
Route = Use NAT but do not include report in headers.
·
Allow RTP Reinvite
By default, the system will route media steams from SIP endpoints through
itself. Enabling this option causes the system to attempt to negotiate the
endpoints to route packets to each other directly, bypassing the system. It is not
always possible for the system to negotiate endpoint-to-endpoint media
routing.
Figure 6-51
3)Codecs
A codec is a compression or decompression algorithm that used in the
transmission of voice packets over a network or the Internet.
u-law: A PSTN standard codec, used in North America, that provides very
good voice quality and consumes 64kbit/s in each direction (receiving and
transmitting) of a VoIP call.
www.yeastar.com
Page95
MyPBX U300 Administrator's Guide
a-law: A PSTN standard codec, used outside of North America, that
provides very good voice quality and consumes 64kbit/s in each direction
(receiving and transmitting) of a VoIP call.
GSM: A wireless standard codec, used worldwide, that provides adequate
voice quality and consumes 13.3kbit/s in each direction (receiving and
transmitting) of a VoIP call. GSM is supported by many VoIP phones.
SPEEX: Speex is an Open Source/Free Software patent-free audio
compression format designed for speech. The Speex Project aims to lower
the barrier of entry for voice applications by providing a free alternative to
expensive proprietary speech codecs. Moreover, Speex is well-adapted to
Internet applications and provides useful features that are not present in
most other codecs.
G.722:G.722 is a wideband speech coding algorithms which supports the bit
rate of 64, 56 and 48kbps wideband. It‟s a broadband voice encoding of G
series.
G.726: A PSTN codec, used worldwide, that provides good voice quality and
consumes 32kbit/s in each direction (receiving and transmitting) of a VoIP
call. G.726 is supported by some VoIP phones.
ADPCM, G.729A, H261, H263, H263p, H264,MPEG4.
Note: If you would like to use G.729, please enter your license.
Figure 6-52
4)QOS
QoS (Quality of Service) is a major issue in VOIP implementations. The issue
is how to guarantee that packet traffic for a voice or other media connection
will not be delayed or dropped due interference from other lower priority
traffic. When the network capacity is insufficient, QoS could provide priority
to users by setting the value.
www.yeastar.com
Page96
MyPBX U300 Administrator's Guide
Figure 6-53
5) Advanced Settings
·
From Field
Where to get the caller ID in sip packet.
·
To Field
Where to get the DID in sip packet.
·
180 Ringing
It is set when the telecom provider needs. Usually it is not needed.
·
Qualify
Send check alive packets to the sip provider.
·
Remote Party ID
Whether send Remote-Party-ID on SIP header. Default no.
·
Allow Guest
Whether allow anonymous registration extension. Default: no.
This option is used to avoid some anonymous calls by hackers. More details for
the system security configuration, please refer to APPENDIX G MyPBX
Security Configuration Guide.
·
Pedantic
Enable pedantic parameter. Default: no.
·
Session -timers
Enable sesstion-timer mode, default: yes
www.yeastar.com
Page97
MyPBX U300 Administrator's Guide
·
Sesstion-expires
The max refresh interval
·
Sesstion-minse
The min refresh interval, which mustn't be less than 90s
·
Sesstion-refresher
Choose sesstion-refersher, the default is Uas
6.7.2 IAX Settings
Figure 6-54
1) General
·
Bind Port
Port use for IAX2 registrations, Default is 4569.
·
Bandwidth
Low/medium/high with this option you can control which codec to be used.
·
Min Registration Time
Minimum duration (in seconds) of a IAX2 registration. Default is 60seconds.
·
Max Registration Time
Maximum duration (in seconds) of a IAX2 registration. Default is 1200 seconds.
2)Codecs
A codec is a compression or decompression algorithm that used in the
transmission of voice packets over a network or the Internet.
u-law: A PSTN standard codec, used in North America, that provides very
good voice quality and consumes 64kbit/s in each direction (receiving and
transmitting) of a VoIP call.
www.yeastar.com
Page98
MyPBX U300 Administrator's Guide
a-law: A PSTN standard codec, used outside of North America, that
provides very good voice quality and consumes 64kbit/s in each direction
(receiving and transmitting) of a VoIP call.
GSM: A wireless standard codec, used worldwide, that provides adequate
voice quality and consumes 13.3kbit/s in each direction (receiving and
transmitting) of a VoIP call. GSM is supported by many VoIP phones.
SPEEX: Speex is an Open Source/Free Software patent-free audio
compression format designed for speech. The Speex Project aims to lower
the barrier of entry for voice applications by providing a free alternative to
expensive proprietary speech codecs. Moreover, Speex is well-adapted to
Internet applications and provides useful features that are not present in
most other codecs.
G.726: A PSTN codec, used worldwide, that provides good voice quality and
consumes 32kbit/s in each direction (receiving and transmitting) of a VoIP
call. G.726 is supported by some VoIP phones.
ADPCM, G.729A, H261, H263, H263p, H264.
Note: If you would like to use G.729, please enter your license.
6.7.3 Blacklist
Blacklist is used to block an incoming/outgoing call. If the number of
incoming/outgoing call is registered in the number blacklist, the caller will hear
the following prompt: “The number you have dialed is not in service. Please
check the number and try again”. The system will then disconnect the call.
We can add a number with the type: inbound, outbound or both
Figure 6-55
Note: It will not working for internal extension number.
www.yeastar.com
Page99
MyPBX U300 Administrator's Guide
6.7.4 Callback Settings
MyPBX allows caller A to dial an inbound route number, and after hearing the
ring, A can hang up the call or wait for MyPBX to cut off the call, then MyPBX will
call A with this number. When a pick up the call, A can dial the number he wants
to call; MyPBX will call the number with its outbound route.
Note:
1. If you‟d like to use callback feature, please make sure if it‟s enabled on the
inbound route setting panel.
2. No callback rules needed to be set if the trunk supports call back with the
caller ID directly.
Figure 6-56
·
Allow All Numbers
If you want to apply Callback function to all incoming numbers, please tick Allow
All numbers.
Follow the step to use this function.
Step 1: Enable Callback.
Inbound Routes –Choose “Yes” on ”Enable Callback” to enable this function
Figure 6-57
www.yeastar.com
Page100
MyPBX U300 Administrator's Guide
Step 2: Create Callback number
Figure 6-58
Step 3: Create Callback Rules
You will need to create callback rules when the system should strip or add digits.
Figure 6-59
·
Trunk Name
Choose the trunk with callback rules
·
Strip digits from front
Define how many digits will be stripped from the call in number before the
callback is placed. For example, when you call from number 123456789 into
MyPBX, the caller ID is 0123456789, but you can only call 123456789
successfully from MyPBX trunk. You should configure number 0123456789 as
the call back number and strip 1 digit before the callback is placed
·
Prepend before dialing
Define digits added before a callback number before the callback is placed. For
example, the call in number (Caller ID) is 123456789, MyPBX need to send
9123456789 to its trunk when call to this number. You should configure
123456789 as the call back number and add 9 before the callback is placed. You
can add „w‟ for analog trunks for some delay too
6.7.5 DNIS Settings
DNIS (Dialed Number Identification Service) is a telephone service that
identifies for the receiver of a call the number that the caller dialed
www.yeastar.com
Page101
MyPBX U300 Administrator's Guide
Figure 6-60
Note: If DID is not configured here, all the calls via this trunk will show the DNIS
instead of the original caller ID
6.7.6 DISA
DISA (Direct Inward System Access) allows someone calling in from outside the
telephone switch (PBX) to obtain an „internal‟ system dial tone and make calls as
if they were using one of the extensions attached to the telephone switch. To use
DISA, a user calls a DISA number, which invokes the DISA application. The DISA
application in turn requires the user to enter a PIN number, followed by the
pound sign (#). If the PIN number is correct, the user will hear dial tone on
which a call may be placed. Obviously, this type of access has serious security
implications, and great care must be taken not to compromise your security
Figure 6-61
www.yeastar.com
Page102
MyPBX U300 Administrator's Guide
1) General
·
DISA Name
Give this DISA application a name to help you identify it.
·
PIN#
The password for this DISA .
·
Response Timeout
The maximum amount of time the system will wait before hanging up the call if
the user has dialed an incomplete or invalid number. Default is 10 seconds.
·
Digit Timeout
The maximum amount of time permitted between each digit when the user is
dialing an extension number. Default is 5 seconds.
2) Member Outbound Routes
Used to set the outbound routes that can be accessed from this DISA.
6.7.5 PIN User Settings
PIN User is used to manage lists of PINs that can be used to access restricted
features such as Outbound Routes.
Figure 6-62
1) Options
·
Access Code
.Dial this code to access PIN.
·
Prompt for Entry
Prompt caller enter the PIN Number.
·
Prompt for Entry Failure
Prompt the caller when an invalid PIN is entered.
www.yeastar.com
Page103
MyPBX U300 Administrator's Guide
Figure 6-63
2) PIN User
MyPBX can store a number of PIN Users. PIN Users may be used to keep track
of calls in relation to particular activities or clients. They can also be used to
keep track of calls by particular users or sets of users.
• PIN entered are checked against those stored by the system. If an invalid PIN
is entered, the PIN is requested again.
• The system administrator can configure certain numbers or types of numbers
to require entry of a PIN before you can continue making a call to such a
number.
• The system administrator can also configure you to have to enter a PIN before
making any external call.
·
Name
A character-based name for this PIN list, i.e. „Yeastar PIN‟
·
PIN List
Enter a list of one or more PINs, One PIN per line.
·
Outbound Route
PIN User can use those outbound route to make call out
www.yeastar.com
Page104
MyPBX U300 Administrator's Guide
6.7.8 Paging Groups
Paging is used to make an announcement over the speakerphone to a phone or
group of phones. Targeted phones will not ring, but instead answer immediately
into speakerphone mode. Please note that this section is for configuring paging
groups. If you would like to configure Intercom settings, please open the Other
Settings -> Feature Codes screen.
This feature is supported by the following SIP phones:
Yealink's T28, T26,T22,T20,T10T,T9CM. Other SIP devices may also work with
this feature but are not officially supported.
Note: A paging group can have a maximum of 20 members.
Figure 6-64
There are two types of paging groups in MyPBX U300
1. Internal paging Group
In this mode, if you dial its number, MyPBX will help to pick up those chosen
members and you can talk directly without any rings.
Figure 6-65
·
Paging Group Number
Define the numbered extension that may be dialed to reach this group.
www.yeastar.com
Page105
MyPBX U300 Administrator's Guide
·
Duplex
Paging is typically one way for announcements only. Checking this will make
paging duplex, allowing all users in the group to talk and be heard by all.
2. External paging group
In this mode, the chosen extensions will have the rights to dial the group
number, all his voice will be broadcasted via the „Audio Out‟ interface of U300
Figure 6-66
www.yeastar.com
Page106
MyPBX U300 Administrator's Guide
7 Reports
Click
to access
We can check the call detailed logs for counting and system log for debugging
7.1 Call Logs
The call Log captures all call details, including call time, caller number, callee
number, call type, call duration, etc. An administrator can search and filter call
data by filter the call logs by call date, caller/callee, trunk, duration, billing
duration, status, communication type, Pin User.
Figure 7-1
7.2 System Logs
You can download and delete the system logs of MyPBX
www.yeastar.com
Page107
MyPBX U300 Administrator's Guide
Figure 7-2
Options
·
Enable Hardware Log
Save the information of hardware; (up to 4 log files)
·
Enable Normal Log
Save the prompt information; (up to 16 log files)
·
Enable Web Log
Save the history of web operations (up to 2 log files)
·
Enable Debug Log
Save debug information (up to 2 log files)
We can also enable the SIP/RTP/E1 debug, it‟s very useful for checking
problems.
2) Packet Capture Tool
This feature always used to capture packets for technician. Integrate packet
capture tool „Wireshark‟ in MyPBX.
Users also could specify the destination IP address and port to get the packets.
·
IP
Specify the destination IP address to get the packets.
·
Port
Specify the destination Port to get the packets.
8 Logout
Click
to log out safely to the log in page.
www.yeastar.com
Page108
MyPBX U300 Administrator's Guide
9. Use MyPBX
Figure 9-1
9.1 Make outbound call
To make an outbound call, we need to add trunk first. There are 3 types of VoIP
Trunk:
·
Digital Trunk: E1/T/J1 ports of MyPBX, connected to the ISDN provider.
You need to get the detailed signaling type from the provider before configure
the E1 trunk.
·
VoIP Trunk: Connected to remote VOIP service server.
You should get an IP address with user name/ password from the provider.
·
Service Provider: Connected to service provider server.
You will get only IP address for authorization.
9.1.1 Sample Routing via E1 Trunk
Let‟s route all inside extensions through an E1 trunk by dialing 9. In
Outbound Routes, add a new outbound route as below.
www.yeastar.com
Page109
MyPBX U300 Administrator's Guide
Figure 9-1
As we can see from the outbound route of „pstnout‟, all phone numbers
starting with 9 will have their first digit stripped off (digit 9) and will be sent
to the E1.
After we have configured the above, we can dial 9 + local number to dial out
via a E1 trunk.
Note: Setting number prefix to wild card X. and setting Strip to 0 digits from
the front will allow all calls to go through this outbound route directly.
9.1.2 Sample Routing via VoIP Trunk
Let‟s configure all inside extensions to dial „0‟ through the VoIP Trunk.
1. Add VoIP service provider
Before we do add this, please make sure you have a VoIP Trunk account.
TrunksVoIP Trunk SIP Trunk
www.yeastar.com
Page110
MyPBX U300 Administrator's Guide
Enter your account information on this page, and click Save.
Figure9-2
2. Add Outbound Routes
As we can see from the Outbound Route of „voipout‟, all phone numbers
starting with 0will have their first digit stripped off (digit 0) and will be sent
to the SIP Trunk.
www.yeastar.com
Page111
MyPBX U300 Administrator's Guide
Figure9-3
Now that we have added two outbound dialing rules, any call starting with 9
will be routed to the PSTN, and any number starting with 0 will be routed to
the SIP Trunk.
9.2 Incoming call
9.2.1 Sample Routing to an IVR
Let‟s configure an incoming call to route to the IVR. In the IVR itself, let‟s
configure digit 0to route the call to extension 500, and digit 1 to route the
call to extension 501.
1. Add IVR
To add a new IVR, go to IVR Create New IVR
www.yeastar.com
Page112
MyPBX U300 Administrator's Guide
Figure9-4
2. Add Inbound Routes
As we can see from the Inbound Route of „allin‟, all incoming calls will be sent
to the IVR.
www.yeastar.com
Page113
MyPBX U300 Administrator's Guide
Figure9-5
www.yeastar.com
Page114
MyPBX U300 Administrator's Guide
APPENDIX A FAQ
Q1. How to Register SIP device?
A1:
1)Register SIP softphone
Download the x-lite softphone from counterpath website
www.counterpath.com
After install the x-lite, right click the panel and select the SIP Account setting
and then configure it.
Display Name: 500
User Name: 500
Password: 500
Authorization Name: 500
Domain: 192.168.5.150
2) Register IP Phone (for example, Yealink‟s T28 IP Phone)
a) Connect the T28‟s Internet port to the switch. And it can get the IP from
your route.
b) Press the „OK‟ key on T28 to get the IP of T28.
c) Put the IP on web browser then you can enter the T28 configure page
through this IP.
d) Put the SIP extensions info on the T28 IP phones.
Display Name: 501
User Name: 501
Register Name: 501
Password: 501
SIP Server: 192.168.5.150
Use the same method register another T28 to other extension.
Q2. How do I reset MyPBX back to the factory default settings?
A2: To perform a reset, please follow steps below:
Step 1:Hold downthe „Reset‟ button on the back of the unit for 5 seconds
and watch the LEDs on the front of the MyPBX. When the status LED turns
red, let go of the reset button.
Step2:When the RUN status LED starts blinking,MyPBX will be set back to
factory defaults.
Step 3: To access the configuration page, navigate to192.168.5.150using a
web browser. Make sure that you are on the 192.168.5.0 subnet before
doing this.
Step4: Login to the device with the username „admin‟ and the password
„password‟, in order to begin reconfiguring the device.
www.yeastar.com
Page115
MyPBX U300 Administrator's Guide
APPENDIX B How to Configure
Autobackup
Before Autobackup can be properly configured, an SMB share folder
accessible from MyPBX must be set up on a Windows based machine. Once
that has been set up, please follow the steps below.
Step 1 Add a new folder, rename it, and set this new folder‟s share
Properties according to Figure B-1
Figure B-1 Set up share Properties
Step 2Enter the new folder and create a new text file, then rename this file
to status.txt. This step is very important, DO NOT forget to create the
status.txt file.
Step 3ConfigureAutobackup settings on MyPBX to Figure B-2
www.yeastar.com
Page116
MyPBX U300 Administrator's Guide
Figure B-2 Autobackup Setting
Net-Disk Host/IP:Change this to the IP address of the computer where
backup files will be stored.
Net-DiskShare Name: Change this to the name of the shared folder where
backups will be stored.
Net-DiskShare Username: The user name used to log into the network
share. Leave this blank if it is not required
Net-DiskShare Password: The password used to log into the network
share.Leave this blank if it is not required
If configuringis correctly, open your Windows share folder to see if the
MyPBX backup files and folders has been created.If the contents of the
backup folder look similar to Figure B-3, then you have successfully
configured Autobackup on the MyPBX unit.
Figure B-3 Autobackup setting succeed
www.yeastar.com
Page117
MyPBX U300 Administrator's Guide
APPENDIX C How to Configure
NAT setting
When MyPBX is behind a NAT(firewall),you need to configure NAT
setting on MyPBX if you want to use a remote extension.
Please follow section 1 or 2 below depending on your network configuration.
1. If MyPBX is connected to a local network, you must set up port forwarding
on your router. Specifically, you must map port 5060 (default SIP port) and
port 10001-10200(default RTP port range) as UDP ports.
Next, go to the MyPBX web interface and configurethe SIP settings according
to Figure C-1:
External IP Address: your router‟s public IP address
External Host: your router‟s domain
ExternalRefresh Interval: 20 seconds
Local Network Identification:192.168.5.0/255.255.255.0 (change this
according to your network configuration)
NAT mode: Yes
Allow RTP Reinvite: No
Figure C-1
Assuming that your router‟s host address is yeastar.3322.org, your local
network is from 192.168.5.1-192.168.5.254, and the subnet Mask is
255.255.255.0, the MyPBX network settings should configured like Figure
C-2
www.yeastar.com
Page118
MyPBX U300 Administrator's Guide
Figure C-2 MyPBX Network setting
2. If MyPBX has a public IP, (i.e. is connected directly to your internet service
provider), the network settings should be configured according to Figure
C-3:
Figure C-3
Next, you should configure the NAT settingsaccording to Figure C-4
Figure C-4
External IP Address: The public IP address of MyPBX
External Host: Leave this blank if no domain has been configured
ExternalRefresh Interval: Leave this blank
Local Network Identification: Leave this blank
NAT mode: Yes
Allow RTP Reinvite: No
www.yeastar.com
Page119
MyPBX U300 Administrator's Guide
APPENDIX D How to Use Auto
Provision
Step1. Disable DHCP Server on your local network.
E.g. Disable DHCP Server on Linksys Router.
Figure D-1
Step2. Enable DHCP Server on MyPBX.
Login MyPBX web interface, System Settings  DHCP Server  Enable DHCP
Server.
www.yeastar.com
Page120
MyPBX U300 Administrator's Guide
Figure D-2
Step3. Configure phones on MyPBX auto-provision page.
1. Login MyPBX web interface, Basic  Auto Provision  Create New Phone.
Figure D-3
2. Fill in the phone detail message on the pop-up windows.
Input IP Phone‟s MAC address, configure Name, Callwaiting,
Extension,Label, Line active for the phone.
www.yeastar.com
Line,
Page121
MyPBX U300 Administrator's Guide
Figure D-4
Step4. Turn on the power and connect the network cable to IP Phone.
Remark: The factory default setting of DHCP for IP Phone is enable, so you can
skip this step to step 5.
If the DHCP is disable, please follow below step to enable it. (e.g.: Yealink‟s IP
Phone).
1. Login IP phone‟s web page.
2. Enable DHCP.
Figure D-5
Step5. Finish.
www.yeastar.com
Page122
MyPBX U300 Administrator's Guide
APPENDIX E HowDo I Configure
Distinctive Ring Tones
Step1: On your IP phone, navigate to the Phone settings web configuration
page and find the Distinctive Ring Tone section.
For each custom ring tone, enter the Internal Ringer Text (can be digits or text)
to trigger the ring tone. For example, you may enter “Family”.
e.g.: Yealink‟s IP phone.
FigureE-1
Step2.Configure the „Distinctive Ringtone‟ on MyPBX.
MyPBX web interface, Inbound Routes Edit Inbound Route, fill in the Internal
Ringer Text on „Distinctive Ringtone‟.
www.yeastar.com
Page123
MyPBX U300 Administrator's Guide
FigureE-2
Step3. Finish.
www.yeastar.com
Page124
MyPBX U300 Administrator's Guide
APPENDIX F How to Use DID
Direct inward dialing (DID), also called direct dial-in (DDI) in Europe and
Oceania, is a feature offered by telephone companies for use with their
customers' private branch exchange (PBX) systems. In DID service the
telephone company provides one or more trunk lines to the customer for
connection to the customer's PBX and allocates a range of telephone numbers to
this line (or group of lines) and forwards all calls to such numbers via the trunk.
MyPBX support DID, you can configure DID in inbound route. Related settings:
DID Number, Extension, Destination.
Figure F-1
·
DID Number
Define the expected DID Number if this trunk passes DID on incoming calls.
Leave this field blank to match calls with any or no DID info. Only service
provider, E1 trunks, BRI trunks or SIP trunks need to be configured with this
setting.
You can also use pattern matching to match a range of numbers.The following
patterns may be used:
X: Any Digit from 0-9
Z: Any Digit from 1-9
www.yeastar.com
Page125
MyPBX U300 Administrator's Guide
N: Any Digit from 2-9
[12345-9]: Any digit in the brackets (in this example, 1,2,3,4,5,6,7,8,9)
The „.‟Character will match any remaining digits. For example, 9011. will match
any phone number that starts with 9011, excluding 9011 itself.
The „!‟ will match none remaining digits, and causes the matching process to
complete as soon as it can be determined that no other matches are possible.
·
Extension
Define the extension for DID number, this field only valid when use E1 trunk for
this inbound router.You can only input number and '-' in this field, and the
format can be xxx or xxx-xxx.The count of the number must be only one or
equal the count of the DID number.
·
Destination
If you don‟t set the extension, you can set the destination of the call here.
Example 1:
Step1: You set the DID number (5503XXX in this example).
Step2: You choose the destination(Ring Group in this example).
The configuration of this example means when the incoming call with DID
number 5503XXX (7 digits number start with 5503) will go to the destination
Ring Group.
If you choose the destination, please leave the Extension form blank.
www.yeastar.com
Page126
MyPBX U300 Administrator's Guide
Figure F-2
Example 2:
Step1: You set the DID number (6001-6099 in this example).
Step2: You set the Extension (6001-6099 in this example).
The configuration of this example means when the incoming call with DID
number 6001 to 6099 will go to the destination 6001 to 6099(number 6001 to
extension 6001, number 6002 to extension 6002).
The destination you set below will be disabled if you set the Extension.
www.yeastar.com
Page127
MyPBX U300 Administrator's Guide
Figure F-3
www.yeastar.com
Page128
MyPBX U300 Administrator's Guide
APPENDIX
G
MyPBX
Security
configuration Guide
VoIP attacks, although it is not an everyday occurrence, it does exist. While
using VoIP, system security is undoubtedly one of the issues we care about most.
But with the appropriate configuration, and some basic safety habits, we can
improve the security of the telephone system. Moreover, the powerful built-in
firewall function in MyPBX is adequate to enable the system to run safely and
stably.
This guide will introduce the highest defense level in MyPBX, and we strongly
recommend that you configure firewall and other security options according to
this guide, to prevent the attack fraud and the system failure or calls loss.
Note: In this guide, the configuration options marked with „*‟ only exist in
12.17.XX.XX and above versions, namely, 3.2 guest calls option, 3.3 remote
registered option, and 5 alarm settings.
1. Security Configuration for Web GUI
1.1 Change the default access port for HTTP on
Options page
PBXBasic SettingsGeneral PreferencesHTTP Bind Port
www.yeastar.com
Page129
MyPBX U300 Administrator's Guide
Figure G-1
1.2 Change the default password for the web GUI
SystemSystem PreferencesChange Password
FigureG-2
2. Disable SSH on LAN Settings Page
2.1 Disable SSH
Select LAN SettingsEnable SSH. If external debugging isn‟t required, please
select “No”.
www.yeastar.com
Page130
MyPBX U300 Administrator's Guide
Figure G-3
2.2 Change the default password for SSH
We can use the Linux command passwd to change root password of MyPBX.
1. Login via putty.exe
Figure G-4
2. The default username is root and the default password is ys123456.
www.yeastar.com
Page131
MyPBX U300 Administrator's Guide
Figure G-5
3. Step 2 use command passwd to change the root‟s password
Figure G-6
3. Security Configuration for Extensions
3.1 Change the default SIP Port
PBXBasic settingsSIP SettingsGeneralUDP Port
www.yeastar.com
Page132
MyPBX U300 Administrator's Guide
Figure G-7
3.2*Disable guest calls
PBXBasic settingsSIP SettingsAdvanced SettingsAllow Guest
Figure G-8
www.yeastar.com
Page133
MyPBX U300 Administrator's Guide
3.3* Security Configuration for remote extensions
If remote registration isn‟t required, please disable it.
PBXExtensionsFXS/VoIP
ExtensionsVoIP
ExtensionsGeneralVoIP
Settings
Figure G-9
3.4 Set an enhanced password and enable IP
restriction for extensions
1) Set a new extension password at the higher security level, e.g. AjK5Up1G.
PBXExtensionsFXS/VoIP ExtensionsVoIP ExtensionsGeneralPassword
Figure G-10
2) Enable IP restriction and enter the permitted “IP address/Subnet mask”, e.g.
192.168.5.136.
www.yeastar.com
Page134
MyPBX U300 Administrator's Guide
Figure G-11
4. Setup Proper Firewall Rules
Note: Please backup the configurations on backup and restore page before you
go ahead.In the case that you lock the device, you can reset to factory default
and restore the previous configurations. Below example rules works with MyPBX
firmwareversion 2.15.xx.xx or higher versions.
Step1. Enable firewall on firewall page of MyPBX.
SystemFirewall SettingsFirewall RulesGeneral Settings
www.yeastar.com
Page135
MyPBX U300 Administrator's Guide
Figure G-12
Step2.Add a common rule to accept local network access.
Create a common rule to allow the all the IP addresses of the local phones to
access MyPBX server. For example, if the IP addresses of the local network are
192.168.5.1-254, the configurations could be as below:
Name: LocalNetwork
Protocol: BOTH
Port: 1:65535
IP: 192.168.5.0/255.255.255.0
Action: Accept
Figure G-13
Step3. Create common rules to accept remote extensions or remote
administrators, if you use SIP trunk, please accept the provider‟s host as well.
Note: If there are no remote extensions, the rule is not required.
1) Set up the firewall rule to allow the public IP address of remote extensions to
access MyPBX server. e.g.110.111.132.6, the configurations could be as
below:
Name: Remote Extension
Protocol: BOTH
Port: 1:65535
IP: 110.111.132.6/255.255.255.255
Action: Accept
www.yeastar.com
Page136
MyPBX U300 Administrator's Guide
Figure G-14
Step4.Configure auto blacklist rules
Auto blacklist rules: the Server would add the IP address to the blacklist
automatically if the number of the packets it sends exceed the rule you
configured.
1) Add two auto blacklist rules for port: 5060.
Rule No.1:
Port: 5060
Protocol: UDP
IP Packets: 120
Time Interval: 60 seconds
Figure G-15
Rule No.2:
Port: 5060
Protocol:UDP
IP Packets: 40
Time Interval: 2 seconds
www.yeastar.com
Page137
MyPBX U300 Administrator's Guide
Figure G-16
2) Add an auto blacklist rule for Port:8022
Rule No.3
Port:8022
Protocol: TCP
IP Packets: 5
Time Interval: 60 seconds
Figure G-17
Step 5. Add a Firewall Rule for VoIP trunk registration
Note: If there is no VoIP trunk, this rule is not required. And if the RTP IP
address of VoIP trunk and Registration IP address of the VoIP trunk are different,
we need create a rule to accept the RTP IP address too.
Add a rule to accept the IP address of the VoIP trunk to access MyPBX server. For
example: If the IP address of the VoIP trunk is 110.5.14.6, Protocol is UDP and
Port is 5060, the configuration could be as below:
Name: VoIPTrunk
Protocol: UDP
Port: 5060: 5060
IP: 110.5.14.6/255.255.255.255
Action: Accept
www.yeastar.com
Page138
MyPBX U300 Administrator's Guide
Figure G-18
Step6. Add a firewall rule to accept the remote access of HTTP port. For
example, if the remote access IP is 110.5.14.6, and the port is 80, the
configuration could be as below.
Name: RemoteHTTP
Protocol: TCP
Port: 80:80
IP: 110.5.14.6/255.255.255.255
Action: Accept
Figure G-19
Step 7. Add a firewall rule to accept remote access of SSH port. For example: if
the remote access IP is 110.5.14.6 and the port is 8022.
www.yeastar.com
Page139
MyPBX U300 Administrator's Guide
Note: If the remote access of SSH port is not needed, this rule is not required.
Name: RemoteSSH
Protocol: TCP
Port: 8022:8022
IP: 110.5.14.6/255.255.255.255
Action: Accept
Figure G-20
Step 8. Add other firewall rules by yourself. For example, if you are using
features about email, you should add the firewall rules for the SMTP server and
POP3 server.
Step 9. Enable Drop all (If this feature is enabled, all the packets and
connection that do not match the rules would be dropped.)
Note: Before enable this feature, please add a rule to accept the local network
access, or the server might not be accessed.
Figure G-21
www.yeastar.com
Page140
MyPBX U300 Administrator's Guide
Step 10. The Configuration of firewall settings is completed. See as below
figure.
Figure G-21
Figure G-22
Step 11. Define the authorized data transmitting rate and drop all other unauthorized hosts.
Note: If we setup IP blacklist rules here, those unauthorized hosts will still be able to send SIP
packets into MyPBX if the packets transmitting rate is under the rate defined. But as soon as the
transmitting beyond the define rate, the IP will be added into blacklist automatically.
This is useful for remote extension who is using dynamic IP address.
www.yeastar.com
Page141
MyPBX U300 Administrator's Guide
Remove all the IP blacklist rules if you don‟t allowed any other unauthorized
hosts access MyPBX.See as below figure.
Note: If „drop all‟ is not enabled, please don‟t remove the IP blacklist rules in
case the system security hole.
Figure G-23
Figure G-24
5*. Alert Settings
www.yeastar.com
Page142
MyPBX U300 Administrator's Guide
After enabling alert settings‟, if the device is attacked, the system will notify
users the alert via call or e-mail. The attack modes include IP attack and Web
Login.
5.1 IPATTACK
When the system is attacked by some IP addresses, the firewall will add the IP
to auto IP Blacklist and notify the user if it match the protection rule.
Example: Configure to notify extension 500, outbound number 5503301 and
E-mail alert@yeastar.com.
configuration could be as below.
Phone Notification Settings:
Phone Notification: Yes
Number: 500;5503301
Attempts: 1
Interval: 60s
Prompt: default
Note: If there‟s outbound number to notify, the number should be fit with the
dial pattern of outbound route.
E-mail Notification Settings:
E-mail Notification: Yes
To: alert@yeastar.com
Subject:IPAttack
www.yeastar.com
Page143
MyPBX U300 Administrator's Guide
Figure G-25
5.2 WEBLOGIN
Enter the password incorrectly five times when logging in MyPBX Web interface
will be deemed as attack, the system will limit the IP login within 10 minutes and
notify the user.
Example: Configure to notify extension 500, outbound number 5503301 and
E-mail alert@yeastar.com.
configuration could be as below.
Phone Notification Settings:
Phone Notification: Yes
Number: 500;5503301
Attempts: 1
Interval: 60s
Prompt: default
Note: If there‟s outbound number to notify, the number should be fit with the
dial pattern of outbound route.
E-mail Notification Settings:
E-mail Notification: Yes
To: alert@yeastar.com
www.yeastar.com
Page144
MyPBX U300 Administrator's Guide
Subject: WebLogin
Figure G-26
6. Note
If the phenomena of toll fraud have been happened in your MyPBX system. We
are really sorry about that, then please enhance the protection level of your
firewall refer to the above steps.
In addition, please change the all password: Web GUI password, SSH password,
and all extensions password.
<Finish>
www.yeastar.com
Page145