OPERATION AND PARTS MANUAL
MODEL GA3.6H Series
GA-3.6HZ
GA3.6H
GA3.6HA
Portable Generators
(HONDA GASOLINE ENGINE)
Revision #0 (11/01/05)
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PAGE 2 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
NOTE PAGE
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 3
TABLE OF CONTENTS
Multiquip GA-3.6H Series
AC Portable Generators
HONDA GX240K1EDN2
ENGINE
Proposition 65 Warning ............................................. 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Message Alert Symbols .............................. 6-7
Rules for Safe Operation ..................................... 8-10
Specifications (Generator/Engine) .......................... 11
Dimensions ............................................................. 12
General Information ................................................ 13
Load Application ..................................................... 14
Controls and Indicators ...................................... 15-17
Generator Refueling ............................................... 18
Installation .......................................................... 19-20
Pre-Inspection ......................................................... 21
Pre-Inspection (Engine) .......................................... 22
Initial Start-up (Engine) ........................................... 23
Initial Start-up/Generator Operation ....................... 24
Generator Operation/Shutdown.............................. 25
Preparation For Long Term Storage ....................... 26
Maintenance (Engine)........................................ 27-28
Wiring Diagram (GA-3HZ Generator) ..................... 29
Wiring Diagram (GA-3H Generator) ....................... 30
Wiring Diagram (GA-3HA Generator) ..................... 31
Troubleshooting (Engine) ................................... 32-33
Troubleshooting (Generator) .................................. 34
Explanation of Code In Remarks Column ............... 36
Suggested Spare Parts ........................................... 37
Air Cleaner Assembly ......................................... 54-55
Camshaft Assembly ........................................... 56-57
Carburetor Assembly ......................................... 58-59
Control Assembly ............................................... 60-61
Crankcase Cover Assembly ............................... 62-63
Crankshaft Assembly ......................................... 64-65
Cylinder Barrel Assembly ................................... 66-67
Cylinder Head Assembly .................................... 68-69
Fan Cover Assembly .......................................... 70-71
Flywheel Assembly ............................................ 72-73
Ignition Coil Assembly ........................................ 74-75
Piston Assembly ................................................. 76-77
Recoil Starter Assembly..................................... 78-79
Solenoid Assembly ............................................. 80-81
Label Assembly .................................................. 82-83
Terms and Conditions Of Sale — Parts .................. 84
NOTE
Specification and part
number are subject to
change without notice.
Component Drawings
Nameplate and Decals....................................... 38-39
Generator Assembly .......................................... 40-41
Control Box Assembly (GA-3HZ) ....................... 42-43
Control Box Assembly (GA-3H) ......................... 44-45
Control Box Assembly (GA-3HA) ....................... 46-47
Muffler Assembly .............................................. 48-49
Pipe Frame Assembly (GA-3HZ) ....................... 50-51
Pipe Frame Assembly (GA-3H/GA-3.6HA) ........ 52-53
PAGE 4 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
PARTS ORDERING PROCEDURES
www.multiquip.com
Effective: June 1st, 2005
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only):
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
parts@multiquip.com.
Order parts on-line using Multiquip’s SmartEquip website!
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Goto www.multiquip.com and click on
Order Parts to log in and save!
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
NOTE
❒
Specify Preferred Method of Shipment:
✓ Fed Ex/UPS
✓ DHL
✓ Truck
■ Priority One
■ Ground
■ Next Day
■ Second/Third Day
Unless otherwise indicated by customer, all orders are treated as Standard Orders and will ship
within 24 hours. We will make every effort to ship Air Shipments the same day the order is received,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
WE ACCEPT ALL MAJOR CREDIT CARDS!
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 5
GA-3.6H Series — SAFETY MESSAGE ALERT SYMBOLS
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed
at all times when operating this
equipment. Failure to read and
understand the Safety Messages and
Operating Instructions could result in
injury to yourself and others.
Potential hazards associated with the operation of the MQ
GA-3.6H Series Portable Generators will be referenced with
Hazard Symbols which appear throughout this manual, and
Lethal Exhaust Gases
will be referenced in conjunction with Safety Message Alert
Symbols.
WARNING
NOTE
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the MQ Model GA-3.6
Series Portable Generators. Refer to
the engine manufacturers instructions
for data relative to its safe operation.
Before using these generators, ensure that the operating
individual has read and understands all instructions in this
manual.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
DANGER
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
WARNING
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
CAUTI
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
Lethal Exhaust Gas Hazards
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide
ample free flow air.
WARNING
Explosive Fuel Hazards
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
WARNING
Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
WARNING
Respiratory Hazards
ALWAYS wear approved respiratory
protection when required.
PAGE 6 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3H/GA-3HA — SAFETY MESSAGE ALERT SYMBOLS
CAUTION
Rotating Parts Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
CAUTION
CAUTION
Equipment Damage
Hazards
Other important messages are provided throughout this
manual to help prevent damage to your portable generator,
other property, or the surrounding environment.
Accidental Starting Hazards
ALWAYS place the power source, circuit
breakers or ON/OFF switch in the OFF
position, when the generators is not in use,
unless connected to transfer switch.
CAUTION
Eye and Hearing Hazards
ALWAYS wear approved eye and
hearing protection.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 7
GA-3.6H Series — RULES FOR SAFE OPERATION
DANGER
Read this manual!
Failure to follow instructions in this manual may lead
to serious injury or even death! This equipment is to
be operated by trained and qualified personnel only!
This equipment is for industrial use only.
The following safety guidelines should always be used when
operating the GA-3.6H Series Portable Generator:
GENERAL SAFETY
■ DO NOT operate or service this
equipment before reading this entire
manual.
■ This equipment should not be operated by persons under
18 years of age.
■ NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■ NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
■ NEVER operate this equipment under the influence of
drugs or alcohol.
■ ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment when
operating the generator.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ Manufacturer does not assume responsibility for any
accident due to equipment modifications.
■ NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
■ NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or generators.
■ The engine section of this generators requires an adequate
free flow of cooling air. NEVER operate the generator in
any enclosed or narrow
area where free flow of
the air is restricted. If the
air flow is restricted it will
cause serious damage to
the generator or engine
and may cause injury to
people. Remember the
generator's engine gives off DEADLY carbon
monoxide gas.
■ ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■ ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
■ NEVER operate the generators in an
explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■ NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
PAGE 8 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — RULES FOR SAFE OPERATION
■ ALWAYS be sure the operator is familiar with proper safety
precautions and operation techniques before using
generators.
■ NEVER leave the generators unattended, turn off engine
when unattended.
■ Unauthorized equipment modifications will void all
warranties.
■ ALWAYS ensure generators are on level ground before use.
■ DO NOT place hands or fingers inside generators engine
compartment when engine is running.
■ NEVER run engine without air cleaner. Severe engine damage
may occur.
■ NEVER change or adjust the engine speed which has been
set at the factory prior to shipping.
Power Cord Safety
■ NEVER let power cables or cords lay in water.
■ NEVER stand in water while AC power from the generators
is being transfer to a load.
■ NEVER use a defective or frayed power cable. Check the
cable for cuts in the insulation.
■ NEVER use a extension cord that is frayed or damaged where
the insulation has been cut.
■ ALWAYS make certain that proper power or extension cord
has been selected for the job See Table 4.
Grounding Safety
■ ALWAYS make sure that electrical circuits are properly
grounded per the National Electrical Code (NEC) and
local codes before operating generator. Severe injury or
death! by electrocution can result from operating an
ungrounded generator.
Maintenance Safety
■ NEVER lubricate components or attempt service on a running
machine.
■ High Temperatures – Always stop engine and
allow the engine to cool before adding fuel, oil
or performing service and maintenance
functions. Contact with hot! components can
cause serious burns.
■ Keep the machinery in proper running condition.
■ Fix damage to the machine immediately and replace any
broken parts immediately.
■ ALWAYS replace any worn or damaged warning decals.
■ ALWAYS store equipment properly when it is not being used.
Equipment should be stored in a clean, dry location out of the
reach of children and unauthorized personnel.
■ The electrical voltage required to operate the generators can
cause severe injury or even death through physical contact
with live circuits. Turn all circuit breakers OFF before
performing maintenance on the generator.
■ Dispose of hazardous waste properly. Examples of potentially
hazardous waste are used motor oil, fuel and fuel filters.
■ DO NOT use food or plastic containers to dispose of
hazardous waste.
■ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
■ Removing the engine oil drain plug while
the engine is hot will result in hot oil to gush
out of the oil drain plug, therefore causing
severe scalding to any persons in the general
area of the generator.
■ ALWAYS make sure the generators are properly grounded to
a suitable earth ground (GROUND ROD). See installation in
this manual.
■ NEVER use gas piping as an electrical ground.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 9
GA-3.6H Series— RULES FOR SAFE OPERATION
DANGER -ELECTROCUTION HAZARDS
During operation of this generation, there
exists the possibility of electrocution,
electrical shock or burn, which can
cause severe bodily harm or even
DEATH!
Emergencies
■ ALWAYS know the location of the
nearest fire extinguisher.
■ ALWAYS know the location of the nearest
first aid kit.
To avoid these hazards:
NEVER use damaged or worn cables when connecting
equipment to the generator. Make sure power
connecting cables are securely connected to the
generator’s output receptacles, incorrect connections
may cause damage to the generators and electrical
shock.
■ In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
NEVER grab or touch a live
power cord with wet hands, the
possibility exist of electrical
shock, electrocution, and even
death!
NEVER insert any objects
into the output receptacles
during operation. This is
extremely
dangerous.
ALWAYS turn-off the generators and place all circuit
breakers in the “OFF” position when contact with the
output receptacles is required. There exist the possibility
of electrocution, electrical shock or burn, which can
cause severe bodily harm or even death!
Backfeed to a utility system can cause
electrocution and or property damage.
NEVER connect the generators to a
building's electrical system without a
transfer switch or other approved device.
All installations should be performed by
a licensed electrician in accordance
with all applicable laws and electrical
codes. Failure to do so could result in
electrical shock or burn causing serious
injury or even death!
NOTE
In keeping with Multiquip's policy
of constantly improving its
products, the specifications quoted
herein are subject to change without
prior notice.
PAGE 10 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— SPECIFICATIONS (GENERATOR/ENGINE)
Table 1. Specifications
MODEL
Type
60 Hz Generator
GA-3.6H/GA-3.6HA/GA-3.6HZ
2-pole, Brushless Type Revolving Field
Max. Output
3600 Watts
Rated Voltage
120/240 V
Max./Cont. Amps @ 120V
30/26.6
Max./Cont. Amps @ 240V
15/13.3
Main Circuit Breaker
2-Pole 13.5 Amps
Phase
Single Phase
Frequency
60 Hz
Rated Speed
3600 RPM
Power Factor
100%
Fuel Tank Capacity
Approx. 5.0 U.S. Gallons (19 Liters)
170 lbs. (74 Kg.) GA3.6H/GA3.6HA
178 lbs. (81 Kg.) GA3.6HZ
Dry Net Weight
Table 2. ENGINE SPECIFICATIONS
Engine
Model
HONDA GX240K1EDN2
Type
Air-cooled 4 stroke, Single Cylinder, OHV,
Horizontal Shaft Gasoline Engine
Bore X Stroke
2.90 in. X 2.30 in.
(73 mm x 58 mm.)
Displacement
14.81 cc
Max Output
Fuel
Lube Oil Capacity
Speed Control Method
Star ting Method
Dimension
(L x W x H)
Dry Net Weight
8.0 H.P./3600 R.P.M.
Unleaded Automobile Gasoline
2.33 pints
Centrifugal Fly-weight Type
Recoil Star t
14.0 x 16.9 X 16.1 in.
(355 X 430 X 410 mm.)
55.1 lbs (25 Kg.)
Effects of Altitude and Heat
The maximum output of the engines listed above are applicable to supplying electrical power for continuous service at ambient
conditions in accordance with SAE Test cord J607. The above ambient conditions are at standard sea level, with a barometric
reading of 29.92 inches and a temperature of 60 degrees fahrenheit.
Generally, the engine's output power will decrease 3-1/2% for each 1000 feet of altitude above sea level, and 1% for each 10° F
Fahrenheit above the standard temperature of 60° F
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 11
GA-3.6H Series— DIMENSIONS
Figure 2. Dimensions
PAGE 12 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — GENERAL INFORMATION
WARNING
Before connecting this generators to any building’s
electrical system, a licensed electrician must install an
isolation (transfer) switch.
Serious injury or death may result without this transfer
switch.F
GA-3.6H Series Familiarzation
Generator
The Multiquip GA-3.6H series generators have been designed
as a portable dual purpose power source for 60 Hz (single
phase) lighting facilities, power tools, submersible pumps
and other industrial and construction machinery.
These generators are mounted on rubber vibration isolators
that have a steel base backplate which is attached to the
protective steel pipe carrying frame. The protective carrying
frame is made of steel tubing and fully wraps around the
generators to protect against damage. See Figures 2A
through 2E for the basic controls and indicators for the GA3.6H Series generators.
These portable generators are supplied with a electrical
control box. To reduce vibration caused by the engine, the
control box is also placed on rubber isolators.
Control Box
The control box is provided with the following:
■ NEMA L14-20R, twist-lock receptacle,125/250V, 20 amps.
■ NEMA L5-20R, twist-lock receptacle, 125V, 20 amps.
■ NEMA L6-30R, twist-lock receptacle, 250V, 30 amps.
(GA-3.6HZ only)
■ NEMA L5-30R, twist-lock receptacle, 125V, 30 amps.
■ NEMA 5-20R, GFCI duplex receptacle,125V, 20 amps
(GA-3.6HA has two).
■ 13.5 amp main circuit breaker.
■ AC Voltmeter
■ G.F.C.I. Ground Terminal (GA-3.6HZ only)
■ Full Power Switch
■ Idle Control Switch
■ Operation Switch
Excitation System
The GA-3.6H series generators use a magnet attached to a
flywheel to produce AC voltage from a lamp coil beneath
the flywheel. As the magnetic passes the coil it produces
approximately 19-22 AC volts.
This voltage (19-22 VAC) is then sent to the control box that
contains three rectifying diodes:
z Excitation (diode 1)
z Battery (diode 2)
z Slow Down (diode 3)
The AC voltage will pass through the excitation diode that
converts the voltage to DC power.
This DC power is then sent to the excitation windings housed
within the main windings commonly called the "stator".
This voltage is then transferred into the rotor through
induction. The rotor contains two diodes within it which rectify
the DC voltage and send it out through the main windings,
as AC voltage.
Alternator
The alternator, a brushless revolving-field type, is
permanently aligned to the engine through rigid coupling.
Engine
These generators are powered by a 8.0 HP, air-cooled, 4stroke HONDA gasoline engine. Reference Table 2, for
engine specifications.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 13
GA-3.6H Series— LOAD APPLICATION
Single Phase Load — 60 Hz
Always be sure to check the nameplate on the generators
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generators for operating the equipment.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
NOTE
If wattage is not given on the equipment's
name plate, approximate wattage may be
determined by multiplying nameplate
voltage by the nameplate amperage.
WATTS = VOLTAGE x AMPERAGE
The power factor of this generators is 1.0 See Table 3 below
when connecting loads.
Table 3. Power Factor By Load
Type Of Load
Power Factor
Single-phase induction motors
0.4 - 0.75
Electric heaters, incandescent
lamps
1 .0
Fluorescent lamps, mecury
lamps
0.4 - 0.9
Electronic devices,
communication equipment
1.0
Common power tools
0 .8
NOTE
When using a combination of dual
receptacles, total load should not
exceed the rated capacity of the
generator.
To determine the running wattage for your load, multiply
the running wattage as indicated by steps 1, 2, and 3 below:
1.
INCANDESCENT LOADS
Lights, heaters and similar appliances.
Total the running wattage and multiply by 1.
Example:
29 light bulbs @ 100W each = 2.9 KW
use a 3 KW generator.
2.
SMALL MOTORS
Drills and other small power tools.
Total the running wattage and multiply by 2.
Example:
A 1 inch drill runs at 1 KW
use a 2 KW generator.
LARGE MOTORS
Submersible pumps, table saws etc.
Total the running wattage and multiply by 3.
Example:
A conveyor belt runs at 8 KW
use a 24 KW generator.
3.
CAUTION
Motors and motor-driven equipment draw much greater
current for starting than during operation. Always use an
adequate size extension cable which can carry the
required load.
Extension Cables
When electric power is to be provided to various tools or
loads at some distance from the generator, extension cords
are normally used. Cables should be sized to allow for
distance in length and amperage so that the voltage
drop between the generators and point of use (load) is
held to a minimum. Use the cable selection chart (Table 3)
as a guide for selecting proper cable size.
NOTE
The idle control device is operated at a
minimum load capacity of 100W. If the
load capacity is less than 100W, place
the idle control switch in the OFF position.
PAGE 14 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— CONTROLS AND INDICATORS
Figure 2A. Generators Components
1.
2.
3.
4.
Lifting Bail Eye – Attach a rope or chain to this lifting eye
when lifting of the generators is required. Never stand
underneath the generators while it is being lifted. Place
lifting eye in down position when not in use.
AC-Voltmeter – This voltmeter indicates (with a mark) the
rated 60 Hz (single-phase) output voltage. In addition the
voltmeter can also be used as a diagnostic tool. If the
voltmeter indicator (needle) is below the rated voltage,
engine problems may exist (low/high RPM's). To prevent
damage to the generators or power tools turn the generators
OFF and consult your authorized Multiquip service dealer.
Idle Control Switch – The generators are provided with
an automatic idle control device for noise suppression and
reduced fuel consumption. The automatic idle control
automatically engages under a no-load condition. With the
automatic idle control switched “ON”, the engine revolutions
will automatically drop to about 2600 rpm (low-speed
operation) within 3 seconds after the load stops. When the
operation is resumed, the engine speed is automatically
increased to about 3600 rpm (high-speed operation) as
soon as the load is connected.
5.
GFCI Duplex Receptacle – NEMA 5-20R, GFCI receptacle
will provide 120V, 20 amps. (GA-3.6HA has two.)
6.
120V Output Receptacle – NEMA L5-20R twist-lock
receptacle will provide 120V, 20 amps, 60 Hz.
7.
120V Output Receptacle – NEMA L5-30R twist-lock
receptacle will provide 120V, 30 amps, 60 Hz.
8.
120V/240V Output Receptacle – NEMA L14-30R twistlock receptacle will provide (120V, 50 amps, or 240V,
25 amps, 60 Hz.)
9.
Main Breaker – This 2-pole circuit breaker (120/240V,
13.5 amps) protects the generators from short circuiting or
overloading. When starting the generators always have
the circuit breaker placed in the "OFF" position.
10. Ground – This ground connection point should be
connect to a good earth ground (ground rod). GA-3.6H and
GA3.6HA models only
Operation Switch – Place this rocker switch in the "ON"
position (up) for normal operation. To turn-off the generators,
place the operation switch in the "OFF" position (down).
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 15
GA-3.6H Series— CONTROLS AND INDICATORS
NOTE
Model GA3.6HZ shown. Location of Full
Power Switch for Models GA3.6H and
GA-3.6HA, is on front control panel.
Figure 2B. Generators Components
11. Full Power Switch – The generators are provided with a
full power switch. Figures 2C and 2D show simplified wiring
diagrams of the dual voltage system.
When the full power switch is in the 120 volt (up) position,
you can access the full rated power of the generators at
120 volts from the GFCI duplex receptacle and the120V
twist-lock receptacle, or a combination of both receptacles
as long as the total load does not exceed the generating
set capacity.
Figure 3C. 120V Full Power Switch
Simplified Diagram (Up Position)
NOTE
When the full power switch is in the
120V position, the 240V twist-lock
receptacle cannot be used.
When the switch is in the 240 volt (down) position, you can
acess half of the rated power of the generating set at 120
volts from the GFCI duplex receptacle and up to half of the
rated power of the set at 120 volts from 120V twist-lock
receptacle; or full rated power of the set at 240 volts from
the 240V twist-lock receptacle.
Figure 3D. 120/240V Full Power Switch
Simplified Diagram (Down Position)
12. 120V Output Receptacle – NEMA L6-20R twist-lock
receptacle will provide 240V, 20 amps, 60 Hz. GA-3.6HZ
only.
13. GFCI Ground – This ground connection point should be
connected to a good earth ground (ground rod). Applies
to GA3.6HZ only.
PAGE 16 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— CONTROLS AND INDICATORS
NOTE
Models GA3.6H and GA3.6HA shown.
Componet location for GA3.6HZ is
similar.
Figure 2E. Generators Components
14. Fuel Cock Lever – Turn this lever downward to start
(down)the flow of fuel into the carburetor. Turn upward to
stop (up) the flow of fuel.
20. Engine Oil Drain Plug – Remove this drain plug when
draining of the oil from the engine crankcase is required.
Fill with recommeded type oil as listed in Table 4.
15. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
21. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element. NEVER run the
engine without an air cleaner.
16. Muffler/Heat Shield – Used to reduce noise and emissions.
NEVER touch this heat shield when the generator/welder
is in use. Always allow time for the generators to cool down
before performing maintenance.
17. Choke Lever – Used for starting the engine. Close the
choke lever when starting a cold engine or in cold weather
conditions. The choke enriches the fuel mixture. Open the
choke lever if starting a warm engine or in warm weather
conditions.
18. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
19. Engine Oil Filler Cap – Remove this cap/dipstick when
the adding of engine oil is required. See Table 4 for
recommended type engine oil.
22. Fuel Tank Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Replenish with clean unleaded
gasoline. Make sure cap is tightened securely. DO NOT
over fill.
23. Fuel Gauge – This gauge is located on top of the fuel tank.
Read this gauge to determine when fuel is low.
24. Fuel Tank – Fuel tank capacity is 5 gallons (19 liters).
This HONDA engine is equipped
with a low oil shutdown capability. A
built in sensor will automatically turn
NOTE
off the engine should the oil level fall
below a safe operating condition.
Make sure the generators is placed
on level ground. Placing the generators on level ground will
ensure that the low oil sensor will function properly.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 17
GA-3.6H Series — GENERATOR REFUELING
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity
to cool down. In the event of a fuel spill, DO NOT
attempt to start the engine until the fuel residue
has been completely wiped up, and the area surrounding the
engine is dry. If generators is placed in a truck bed with a plastic
liner, REMOVE generators from truck bed and place on ground
(Figure 3) to refuel. This possibility exist of fire or explosion due
to static electricity.
Figure 3. Generators Refueling
PAGE 18 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — INSTALLATION
Outdoor Installation
Indoor Installation
Install the generator/welder in a area that is free of debris,
bystanders, and overhead obstructions. Make sure the
generators is on secure level ground so that it cannot slide
or shift around. Also install the generators in a manner so
that the exhaust will not be discharged in the direction of
nearby homes.
Exhaust gases from gasoline engines are extremely
poisonous. Whenever an engine is installed indoors the
exhaust fumes must be vented to the outside. The engine
should be installed at least two feet from any outside wall.
Using an exhaust pipe which is too long or too small can
cause excessive back pressure which will cause the engine
to heat excessively and possibly burn the valves.
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and grounding.
Eliminate the danger of deadly carbon monoxide gas.
Remember that exhaust fumes from any gasoline engine
are very poisonous if discharged in a closed room, but
harmless if allowed to mix with the outside air. If the generators
is installed indoors, you must make provisions for venting
the engine exhaust to the outside of the building.
Foreign materials such as dust, sand, lint and abrasive
materials have a tendency to cause excessive wear to
engine and alternator parts.
CAUTION
Pay close attention to ventilation when
operating the generators inside tunnels
and caves. The engine exhaust contains
noxious elements.
Mounting
The generators should always be mounted on a flat level
surface to isolate vibration of the generators when it is
running. DO NOT place the generators on slopes, the
possibility exists that the generators could slide.
Generators Grounding
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground. Always use the ground terminal on the generators to
ground the generator. Ground the generators from its ground
connector so that the resistance to ground is 500 ohms or less.
Article 250 (Grounding) of the National Electrical Code (NEC)
provides guide lines for proper grounding and specifies that
the cable ground shall be connected to the grounding system
of the building as close to the point of cable entry as practical.
NEC articles 250-64(b) and 250-66 set the following
grounding requirements:
1. Use one of the following wire types to connect the
generators to earth ground.
a. Copper - 10 AWG (5.3 mm2) or larger.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
CAUTION
An electric shock is apt to happen
when vibrators are used. Pay close
attention to handling when operating
vibrators and always use rubber
boots and gloves to insulate the
body from a short circuit.
2. When grounding the generators (Figure 3) connect the
ground cable between the lock washer and the nut on
the generators and tighten the nut fully. Connect the other
end of the ground cable to earth ground.
3. NEC article 250-52(c) specifies that the earth ground
rod should be buried a minimum of 8 ft. into the ground.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 19
GA-3.6H Series — INSTALLATION
Connecting the Ground
The nut and ground terminal on the generators should always be used to connect the generators to a suitable ground. The
ground cable should be #8 size wire minimum.
At the generator, connect the terminal of the ground cable between the lock washer and the nut (Figure 4) and tighten the
nut fully. Connect the other end of the ground cable to a suitable earth ground (ground rod).
Figure 4. Generators Grounding
PAGE 20 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — PRE-INSPECTION
General Inspection Prior to Operation
Extension Cable
Ground Power Tools
When electric power is to be provided to various tools or loads at
some distance from the generator, extension cords are normally
used. Cables should be sized to allow for distance in length and
amperage so that the voltage drop between the generators and
point of use (load) is held to a minimum. Use the cable selection
chart (Table 3) as a guide for selecting proper cable size.
When using power tools or electrical equipment requireing AC
power from the generator, make sure connecting (power tool)
cable has a ground as shown in Figure 5.
Never! use power tools or
equipment that do not have a
ground capability, the possibility
exists of electrocution, electrical
shock or burn, which can cause
severe bodily harm or even
DEATH!
NOTE
Main Circuit Breaker
To protect the generators from an overload always place the
main circuit breaker in the "OFF" position prior to starting the
engine.
Figure 5. Ground Cables/Plugs
Table 3. Cable Selection (60 Hz, Single Phase Operation)
Current in
Amperes
Load In Watts
Maximum Allowable Cable Length
At 120 Volts
#10 Wire
#12 Wire
#14 Wire
#16 Wire
2.5
300
1000 ft.
600 ft.
375 ft.
250 ft.
5
600
500 ft.
300 ft.
200 ft.
125 ft.
7.5
900
350 ft.
200 ft.
125 ft.
100 ft.
10
1200
250 ft.
150 ft.
100 ft.
15
1800
150 ft.
100 ft.
65 ft.
20
240 0
125 ft.
75 ft.
50 ft.
CAUTION: Equipment damage can result from low voltage.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 21
GA-3H/HA Series — PRE-INSPECTION (ENGINE)
CAUTION
NEVER operate the generators in a confined
area or enclosed area structure that does
not provide ample free flow of air.
Figure 7. Engine Oil Dipstick (Oil Level)
ALWAYS wear approved eye and hearing
protection before operating the generator.
Before Starting
1.
Read safety instructions at the
beginning of manual.
2.
Clean the generator, removing dirt
and dust, particularly the engine
cooling air inlet, carburetor and air
cleaner.
3.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
4.
Check carburetor for external dirt and dust. Clean with dry
compressed air.
5.
Check fastening nuts and bolts for tightness.
Table 4. Oil Type
Season
Temperature
Oil Type
Summer
25°C or Higher
SAE 10W-30
Spring/Fall
25°C~10°C
SAE 10W-30/20
Winter
0°C or Lower
SAE 10W-10
DANGER EXPLOSIVE FUEL
Motor fuels are highly flammable and can
be dangerous if mishandled. DO NOT
smoke while refueling. DO NOT attempt to
refuel the generators if the engine is hot! ,
running or in the dark.
Engine Oil Check
1.
To check the engine oil level, place the generators on
secure level ground with the engine stopped.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 6) and wipe clean.
Fuel Check
1. Close the fuel cock before filling the fuel tank.
2. Remove the fuel cap located on top of fuel tank.
3. Read the fuel gauge located on top of the fuel tank (Figure 8) to
determin if the fuel level is low. If fuel is low, replenish with
clean unleaded fuel.
Figure 8. Fuel Gauge
Figure 6. Engine Oil Dipstick (Removal)
3. Insert and remove the dipstick without screwing it into the filler
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 7), fill to the edge of the oil filler
hole with the recommended oil type (Table 4). Maximum oil
capacity is 1.16 quarts (1.1 liters)
4. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. DO NOT fill the tank beyond capacity.
Wipe up any spilled fuel immediately!
PAGE 22 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— INITIAL START-UP (ENGINE)
CAUTION
2. Place the choke lever (Figure 11) in the "CLOSED " position
if starting a cold engine.
DO NOT attempt to operate this
generators until the Safety, General
Information and Inspection sections of
this manual have been read and
thoroughly understood.
This section is intended to assist the operator with the initial
start-up of the portable generator. It is extremely important that
this section be read carefully before attempting to use the
generators in the field.
Before Starting the Engine
1. Be sure to disconnect all electrical loads from the
generators prior to starting the engine.
2. NEVER start the engine with the main circuit breaker
in the “ON" position. Always place this circuit breakers
(Figure 9) in the OFF position before starting.
Figure 11. Choke Lever
3. Place the choke lever (Figure 11) in the "OPEN " position
if starting a warm engine or the temperature is warm.
4. Place the generator's operation switch (Figure 12) in the
"ON " position.
Figure 12. Generator Operation Switch (ON)
Figure 9. Main Circuit Breaker (OFF Position)
5. Grasp the starter grip (Figure 13) and slowly pull it out. The
resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip
briskly and smoothly for starting.
Starting the Engine
1. Place the engine fuel valve lever (Figure 10) to the "ON"
position.”
Figure 13. Starter Grip
CAUTION
DO NOT pull the starter rope all the way to the end.
Figure 10. Engine Fuel Valve Lever (ON Position)
DO NOT release the starter rope after pulling. Allow it to
rewind as soon as possible.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 23
GA-3.6H Series— INITIAL START-UP/GENERATOR OPERATION
6. If the engine has started, slowly return the choke lever
(Figure 11) to the “OPEN” position. If the engine has not
started repeat steps 1 through 5.
2. Place the full power switch (Figure 17) in the 120V
position (up).
7. Before the generator is placed into operation, run the engine
for 3-5 minutes. Check for abnormal smells, fuel leaks, and
noises that would associate with lose components.
8. Place the idle control switch (Figure 14) in the "OFF"
(down) position. This will allow the engine speed to run
at speed about 3600 RPM's
Figure 17. Full Power Switch 120 V Position (Up)
NOTE
Figure 14. Idle Control Switch (Off)
Placing the idle control switch in
the OFF position (Figure 14) allows
NOTE
the engine to operate at a maximum
speed of about 3600 RPM's. When
the idle control switch is placed in
the up position (ON) (Figure 15),
the generators will run at idle speed (2200 RPM's) until a load is
applied, at that time the engine speed will increase to 3600
RPM's as long as the load is being applied. When the load is not
in use, the engine speed will drop back to the idle mode after
about 3 seconds.
When the full power switch is in the 120 V
position, the 240V twist-lock receptacle
cannot be used.
3. Read the voltmeter on the front panel of the generator
(Figure 18) and verify that120 VAC is present at the
120V twist-lock and GFCI duplex receptacles. For
additional verification of voltage, an external voltmeter
can be used to measure the output voltage as shown in
Figure 18.
Figure 15. Idle Control Switch (On)
Figure 18. 120 V and GFCI Receptacles
60 Hz Operation
1. Place main circuit breaker (Figure 16) in the ON position.
4. Place the full power switch (Figure 19) in the 240V
position (down).
Figure 17. Main Circuit Breaker (ON)
Figure 19. Full Power Switch 240/120 V Position (Down)
PAGE 24 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— GENERATOR OPERATION/SHUTDOWN
5. Read the voltmeter on the front panel of the generator
(Figure 20) and verify that 240 VAC is present at the
240V twist-lock receptacle. Using an external voltmeter
verify that 120V is present at the 120V twist-lock and
GFCI duplex receptacles.
Stopping the Engine
1. Place the main circuit breaker (Figure 21) in the OFF
position.
Figure 21. Main Circuit Breakers (Off)
2. Place the idle control switch (Figure 22) in the OFF
position.
Figure 22. Idle Control Switch (Off)
3. Let the engine run at idle with no load for 2-3 minutes.
4. To shut-down the engine, place the generator's operation
switchg(Figure 23) in the OFF position.e
Figure 20. 60 Hz Output Receptacles
When the full power switch is in the 240
volt (down) position, you can take up to
half of the rated power of the generating
set at 120 volts from the GFCI duplex
receptacle and up to half of the rated power of the set at 120
volts from the 120V twist-lock receptacle; or full rated power
of the genset at 240 volts from the 240V twist-lock
receptacle.
NOTE
NOTE
Figure 23. Generator Operation Switch (Off)
5. Place the engine fuel valve lever (Figure 24) to the "OFF"
position.”
When using a combination of dual
receptacles, total load should not exceed
the rated capacity of the generator.
Connecting the Load
1. If small wattage power tools are required, connect them
to the 60 Hz output receptacles at this time.
Figure 24. Engine Fuel Valve Lever (OFF Position)
6. Remove all loads from the generator.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 25
GA-3.6H Series— PREPARATION FOR LONG TERM STORAGE
Generators Storage
For storage of the generating set for over 30 days, the
following is required:
■ Drain the fuel tank completely, or add STA-BIL to the fuel.
■ Run the engine until the gasoline in the carburetor is
completely consumed.
■ Completely drain the oil from the crankcase and refill with
fresh oil.
■ Remove the spark plug, pour 2 or 3 cc of SAE 30 oil into the
cylinder and crank slowly to distribute the oil.
■ Slowly rotate the engine a few times with the starter Rope and
install a new plug.
■ Pull out the starter rope slowly and stop at the compression
point.
■ Clean all external parts of the generating set with a cloth.
■ Cover the generating set and store in a clean, dry place.
PAGE 26 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— MAINTENANCE (ENGINE)
Use Table 5 as a general maintenance guideline when servicing
your engine. For more detail engine maintenance information,
refer to the engine owner's manual supplied with your engine.
Table 5. Engine Maintenance Schedule
DESCRIPTION (3)
OPERATION
BEFORE
CHECK
X
FIRST
EVERY
MONTH 3 MONTHS
OR
OR
10 HRS.
25 HRS.
EVERY
6 MONTHS
OR
50 HRS.
EVERY
Y E AR
OR
100 HRS.
EVERY
2 YEARS
OR
200 HRS.
Engine Oil
CHANGE
CHECK
X
X
Air Cleaner
CHANGE
All Nuts & Bolts
Re-tighten If
Necessary
X (1)
X
CHECK-CLEAN
X
Spark Plug
REPLACE
X
Cooling Fins
CHECK
X
Spark Arrester
CL E A N
X
Fuel Tank
CLEAN
X
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
X (2)
Valve Clearance
CHECK-ADJUST
Fuel lines
CHECK
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the ROBIN Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 27
GA-3.6H Series— MAINTENANCE (ENGINE)
Maintenance
Perform the scheduled maintenance procedures as defined by
Table 6 and below:
DAILY
■ Thoroughly remove dirt and oil from the engine and control
area. Clean or replace the air cleaner elements as necessary.
Check and retighten all fasteners as necessary. Check the
gearbox for oil leaks. Repair or replace as needed.
WEEKLY
■ Remove the fuel filter cap and clean the inside of the fuel
tank.
■ Remove or clean the filter at the bottom of the tank.
■ Remove and clean the spark plug (Figure 25), then adjust
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This unit
has electronic ignition, which requires no adjustments.
DANGER
DO NOT use gasoline as a cleaning solvent,
because that would create a risk of fire or
explosion.
ENGINE AIR CLEANER
1. Remove the air cleaner cover and foam filter element as
shown in Figure 27.
2. Clean foam element in warm, soapy water or nonflammable
solvent. Rinse and dry thoroughly. Dip the element in clean
engine oil and completely squeeze out the excess oil from the
element before installing.
Figure 25. Spark Plug Gap
ENGINE OIL
1. Drain the engine oil when the oil is warm as shown in
Figure 26.
Figure 27. Engine Air Cleaner
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 4. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
4. Install drain bolt with sealing washer and tighten securely.
Figure 26. Engine Oil (Draining)
PAGE 28 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — WIRING DIAGRAM (3.6HZ)
GA-3.6HZ WIRING DIAGRAM
Figure 28. Generator Wiring Diagram (GA-3.6HZ)
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 29
GA-3.6H Series— WIRING DIAGRAM (3.6H)
GA-3.6H WIRING DIAGRAM
Figure 29. Generator Wiring Diagram (GA-3.6H)
PAGE 30 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6HA — WIRING DIAGRAM (GENERATOR)
GA-3.6HA WIRING DIAGRAM
Figure 30. Generators Wiring Diagram (GA-3.6HA)
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 31
GA-3.6H Series— TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Engine Troubleshooting (Table 6) and
Generator Troubleshooting (Table 7) information shown below
and on the proceeding page. If the problem cannot be
remedied, please leave the unit just as it is and consult our
company's business office or service plant.
TABLE 6. ENGINE TROUBLESHOOTING
SYMPTOM
Poor star ting
Insufficient power output "no
compression"
Insufficient power output
"compression"
POSSIBLE PROBLEM
SOLUTION
Inspect carburetor to see if fuel
is reaching it?
Check fuel line
No Fuel?
Add Fuel
Water in fuel tank?
Flush or replace fuel tank.
Fuel filter clogged?
Replace fuel filter
Stuck carburetor?
Check float mechanism.
Spark plug is red?
Spark plug is fouled. Check tranistor ignition unit.
Spark plug is blue-white?
Insufficient compression, injected air leaking. Carburetor jets are
clogged (overflow).
No spark present at tip of spark
plug?
Tranistor ignition unit broken, high voltage cord cracked or broken.
Star t/Stop switch broken. Replace spark plug if fouled.
No oil?
Add oil as required.
Oil pressure alarm lamp blinks
upon star ting?
Check Automatic shutdown circuit "oil sensor".
Engine will not turn over?
Replace cylinder and piston and if necessary axel joint.
Cylinder head connecting bolts
loose?
Tighten cylinder head connecting bolts.
Cylinder head gasket damaged?
Replace cylinder head gasket.
Malfunction of valve seat?
Re-seat valves.
Spark plug is loose?
Replace spark plug.
Worn piston rings?
Replace piston rings.
Malfunction in air-cleaner
system, air filter clogged?
Clean or replace air filter.
Air leaking in from interface
between carburetor and cylinder
head?
Tighten bolts between carburetor and cylinder head. Replace
cylinder head gasket.
Malfunction in fuel system?
Clean or replace fuel filter.
Clean or replace carburetor.
Check carburetor float.
PAGE 32 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— TROUBLESHOOTING (ENGINE)
TABLE 6. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
Insufficient power output
"compression" and overheats
Burns to much fuel
Exhaust color is continiously
"WHITE"
Exhaust color is continiously
"BLACK"
POSSIBLE PROBLEM
SOLUTION
Malfunction in blower?
Check or replace blower.
Air in-take filter clogged?
Clean or replace air in-take filter.
Over accumulation of exhaust
products?
Clean and check valves.
Check muffler, replace if necessary.
Wrong spark plug?
Replace spark plug with manufactures suggested type spark plug.
Lubricating oil is wrong
viscosity?
Replace lubricating oil with correct viscosity.
Worn rings?
Replace rings
Air cleanner clogged?
Clean or replace air cleaner.
Choke valve has not been set
to the correct position?
Adjust choke valve to the correct position.
Carburetor defective, seal on
carburetor broken?
Replace carburetor or seal.
Poor carburetor adjustment
"engine runs too rich?
Adjust carburetor.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 33
GA-3.6H Series— TROUBLESHOOTING (GENERATOR)
TABLE 7. GENERATOR TROUBLESHOOTING
SYMPTOM
Low voltage
POSSIBLE PROBLEM
SOLUTION
Engine speed too low?
Raise engine speed to rated RPM.
AC voltmeter not working?
Replace AC voltmeter.
Control box internal wiring
malfunction?
Check control box wiring.
Defective ignition coil?
Check red and green ignition wires. Replace ignition wires if
necessary.
Rotor winding malfunction?
Check or replace rotor.
Stator winding malfunction?
Check or replace stator.
Breaker malfunction?
Check or replace CB1.
Voltage output too high.
Engine speed too high?
Lower engine speed to rated RPM.
Voltage output too high. Engine
speed normal 3650 RPM
(unloaded), 2500 RPM (idle)
Control box internal wiring
malfunction
Check control box wiring.
Circuit breaker will not turn on
"NO LOAD"
Defective circuit breaker?
Replace circuit breaker.
Overload?
Reduce load or replace breaker.
Load circuit is shor ted?
Check load circuit for shor t.
Does not accelerate from low to
high "NO LOAD"
Stuck solenoid?
Check solenoid.
Does not accelerate from low to
high "LOAD ACTIVE
Control box interal wiring
defective?
Check control box wiring.
Defective rotor windings?
Check or replace rotor.
Defective solenoid?
Check or replace solenoid.
Defective idle control device?
Check or replace idle control device.
Defective solenoid?
Check or replace idle control device.
Control box wiring malfunction?
Check control box wiring, replace any defective components.
Defective solenoid?
Check or replace solenoid.
Idle control device malfunction?
Check or replace idle control device.
Low voltage. Engine speed
normal 3650 RPM (unloaded),
2500 RPM (idle)
Circuit breaker will turn on
"LOADED" but trips immediately.
Does not decelerate no
"VOLTAGE OUTPUT".
Does not decelerate but has
"VOLTAGE OUTPUT".
PAGE 34 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
NOTE PAGE
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 35
GA-3.6H Series— EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and remarks
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
The contents and part numbers listed in the parts section are
subject to change without notice . Multiquip does not
guarantee the availibility of the parts listed.
Sample Parts List:
NO.
1
2
2
3
4
REMARKS
INCLUDES ITEMS W/
NOT SOLD SEPARATELY
MQ-45T ONLY
MAKE LOCALLY
S/N 2345B AND ABOVE
*
NO. Column
Unique Symbols - All items with same unique symbol
( , #, +, %, or >) in the number column belong to the same
assembly or kit, which is indicated by a note in the “Remarks”
column.
*
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
NOTE
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
PART NO. PART NAME
QTY.
12345
BOLT ....................... 1 ....
WASHER, 1/4 IN. ...........
12347
WASHER, 3/8 IN. .... 1 ....
12348
HOSE .................... A/R ..
12349
BEARING ................ 1 ....
*
*
QTY. Column
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
PART NO. Column
Numbers Used - Part numbers can be indicated by a number,
a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
PAGE 36 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— SUGGESTED SPARE PARTS
GA-3.6H Series1 TO 3 UNITS WITH HONDA
GX240K1EDN2 ENGINE
1 to 3 Units
Qty.
P/N
Description
1 ........0810106004 ..............CAP FUEL TANK (GA3.6HZ)
1 ........A9924800014 ...........CAP FUEL TANK (GA3.6H/3.6HA)
1 ........A9924800004 ...........FILTER FUEL
1 ........7895419004 ..............RUBBER SUSPENSION
4 ........1725419214 ..............RUBBER SUSPENSION
3 ........9807955846 ..............SPARK PLUG
1 ........34150ZH7003 ...........ALERT UNIT, OIL
2 ........28462ZE2W11 .........ROPE, RECOIL
3 ........17211899000 ............ELEMENT AIR CLEANER
NOTE
Part numbers on this Suggested Spare Parts List
may supercede/replace
the P/N shown in the text
pages of this book.
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 37
GA-3.6H Series— NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
PAGE 38 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO.
PART NO.
PART NAME
QTY. REMARKS
1
7910501222
DECAL; CONTROL PANEL ......................................... 1......... GA-3.6HZ ONLY
1
A3511200002
DECAL; CONTROL PANEL ......................................... 1......... GA-3.6H ONLY
1
A3511200402
DECAL; CONTROL PANEL ......................................... 1......... GA3.6HA ONLY
2
87528898620
DECAL; CHOKE ......................................................... 1......... REPLACES P/N 0600500047
3
1980680004
DECAL; FUEL COCK .................................................. 1......... S-3704
4
NAMEPLATE .............................................................. 1......... CONTACT MQ PARTS DEPT.
5
87533ZC0630
DECAL; AIR CLEANER .............................................. 1......... REPLACES P/N 0600500045
6
7910631002
DECAL; MQ MULTIQUIP 3600 ................................... 1......... GA-3.6HZ ONLY
6
A3561000003
DECAL; MQ MULTIQUIP 3600 ................................... 1......... GA-3.6H & GA3.6HA ONLY
7
8700611804
DECAL; WARNING DANGEROUS GAS ..................... 1......... S-4984
8
8700611904
DECAL; DANGER ELECTRICAL SHOCK HAZ. ......... 1......... S-4985
9
0800628504
DECAL; GROUND ....................................................... 1......... S-1123
10
7900638004
DECAL; OPERATING INSTRUCTIONS ...................... 1......... GA-3.6HZ ONLY S-4605
10
A9521200104
DECAL; OPERATING INSTRUCTIONS ...................... 1......... GA-3.6H & GA3.6HA ONLY
11
7900636004
DECAL; CAUTION OPER. AT 3600 RPM ONLY ......... 1......... S-4461
12
0820610404
DECAL; WARNING TRANSFER SWITCH ................... 1......... S-3627
13
35137
DECAL; WARNING READ MANUAL ........................... 1......... GA-3.6H & GA3.6HA ONLY
14
0820610304
DECAL; WARNING READ MANUAL ........................... 1......... GA-3.6HZ ONLY
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 39
GA-3.6H Series— GENERATOR ASSY.
GENERATOR ASSY.
PAGE 40 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— GENERATOR ASSY.
GENERATOR ASSY.
NO.
PART NO.
1
7911002003
1
7901002403
1-1
* 0601823207?
1-2
* 0601823213
1-2
* 0771706304
0601822637
1-3
0071706304
*
2
7901017004
3
0801086104
4
0040010000
5
7911344003
5
A5135000103
6
7901315502
7
7871315022
8
7875021513
8
7875021523
9
7871331003
10
7901316004
11
0040008000
12
0041208000
13
7871329514
14
0601851760
15
0013608020
15A
0040008000
PART NAME
QTY.
REMARKS
ROTOR ASSY. ............................. 1 ........... INCLUDES ITEMS W/ GA-3.6HZ ONLY
*
ROTOR ASSY. ............................. 1 ........... INCLUDES ITEMS W/ GA-3.6H/GA3.6HA ONLY
*
FIELD ASSY. ............................... 1 ........... NOT SOLD SEPERATELY
RECTIFIER, D3SB60 ................... 2 ........... GA-3.6HZ ONLY
RECTIFIER, D3SB80 ................... 2 ........... GA-3.6H & GA3.6HA ONLY
SURGE ABSORBER, .................. 2 ........... TNR15G431K GA-3.6HZ ONLY
SURGE ABSORBER, .................. 2 ........... TNR96431K GA-3.6H/GA3.6HA ONLY
BEARING, 6304 2RU NYCM
1
SET BOLT, ROTOR
1
SET WASHER, BEARING
1
SPRING WASHER
1
ARMATURE ASSY. ...................... 1 ........... GA-3.6HZ ONLY
ARMATURE ASSY. ...................... 1 ........... GA-3.6H & GA3.6HA ONLY
END BRACKET
1
END BRACKET
1
GUIDE PANEL, AIR ..................... 1 ........... GA-3.6HZ ONLY
GUIDE PANEL, AIR ..................... 1 ........... GA-3.6H & GA3.6HA ONLY
COVER
1
SET BOLT, STATOR
4
WASHER, LOCK
4
WASHER, FLAT
4
GROMMET
1
CAP, 0B-13
1
HEX, HEAD BOLT
4
SPRING WASHER
4
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 41
GA-3.6H Series — CONTROL BOX ASSY. (GA-3HZ)
CONTROL BOX ASSY. (GA3.6HZ)
PAGE 42 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — CONTROL BOX ASSY. (GA-3HZ)
CONTROL BOX ASSY. (GA3.6HZ)
NO
PART NO
PART NAME
QTY.
REMARKS
1
7911811403
CONTROL BOX
1
2
0601850102
GROMMET, G3
1
3
0601823853
SLOW DOWN UNIT, ND-80
1
4
0027104010
MACHINE SCREW
2
4A
0207004010
HEX. NUT
2
5
7911821413
CONTROL PANEL
1
6
7910501212
NAMEPLATE, N5431B ................................ 1 ......... S/N 2975451 AND BELOW
6
7910501222
NAMEPLATE, N-5431C ............................... 1 ......... S/N 2975452 AND ABOVE
7
0601800258
AC VOLTMETER, 8283:0-120V.0-240V
1
8
0601805327
CIRCUIT BREAKER, KM-2:265V,13.5A
1
9
4341817004
BRACKET, CIRCUIT BREAKER
1
10
0027104010
MACHINE SCREW
2
11
0601812597
RECEPTACLE, 5-20R, GF5352 (GFCI)
1
12
0601811035
RECEPTACLE, L5-30R,125V,30A
1
13
0601811032
RECEPTACLE, L6-20R, 250V,20A
1
14
0027104010
MACHINE SCREW
6
14A
0207004000
HEX. NUT
6
15
0601830737
FULL POWER SWITCH, ET1330D12
1
16
0601830727
IDLE CONTROL SWITCH, ET115A12
1
17
0601830738
OPERATION SWITCH, ET210K12
1
18
0601815109
GROUND TERMINAL, T-381
1
19
0601823204
RECTIFIER, S5VB60
2
20
0027103020
MACHINE SCREW
2
21
0017105010
HEX. HEAD BOLT
4
22
0805088004
RUBBER CUSHION
2
23
0805088304
COLLAR
2
24
0017106020
HEX. HEAD BOLT
2
25
0017106016
HEX. HEAD BOLT
1
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 43
GA-3.6H Series — CONTROL BOX ASSY. (GA-3H)
CONTROL BOX ASSY. (GA-3H)
PAGE 44 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — CONTROL BOX ASSY. (GA-3H)
CONTROL BOX ASSY. (GA-3H)
NO.
PART NO.
PART NAME
QTY.
1
A3214000003
CONTROL BOX
1
2
0601850102
GROMMET, G-3
1
3
0601823204
RECTIFIER, S5VB60
2
4
0027103012
MACHINE SCREW
2
5
0601823853
SLOW DOWN UNIT, ND-80
1
6
0027104010
MACHINE SCREW
2
6A
0207004000
HEX, NUT
2
7
A3224000003
CONTROL PANEL
1
8
0601804819
CIRCUIT BREAKER, KM-2 21A
1
9
4341817004
BRACKET, CIRCUIT BREAKER
1
10
0021004010
MACHINE SCREW
2
11
0601806819
AC VOLTMETER, DE450-011 0~120/240V
1
12
0601812598
RECEPTACLE, 5-20R
1
13
0601812592
RECEPTACLE, L5-20R
1
14
0601811035
RECEPTACLE, LS-30R
1
15
0601812529
RECEPTACLE, L14-30R
1
16
0021004010
MACHINE SCREW
8
16A
0207004000
HEX, NUT
8
17
0601830737
FULL POWER SWITCH, ET-330D12
1
18
0601831620
IDLE CONTROL SWITCH, C1550WA
1
19
0601831620
OPERATION SWITCH, C1550WA
1
20
0021004015
MACHINE SCREW
1
20A
0207004000
HEX, NUT
1
21
A3262800004
CAPACITOR ASSY., VR1H102MHA, 50V 1000µF 1
22
0017106016
HEX, HEAD BOLT
4
23
0017105010
HEX, HEAD BOLT
4
REMARKS
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 45
GA-3.6H Series — CONTROL BOX ASSY. (GA-3.6HA)
CONTROL BOX ASSY. (GA-3.6HA)
PAGE 46 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — CONTROL BOX ASSY. (3.6HA)
CONTROL BOX ASSY. (3.6HA)
NO.
PART NO.
PART NAME
QTY.
1
A3214000103
CONTROL BOX
1
2
0601850102
GROMMET, G-3
1
3
0601823204
RECTIFIER, S5VB60
2
4
0027103012
MACHINE SCREW
2
5
0601823853
SLOW DOWN UNIT, ND-80
1
6
0027104010
MACHINE SCREW
2
6A
0207004000
HEX, NUT
2
7
A3224000103
CONTROL PANEL
1
8
0601805327
CIRCUIT BREAKER, KM-2 13.5A
1
9
4341817004
BRACKET, CIRCUIT BREAKER
1
10
0021004010
MACHINE SCREW
2
11
0601806819
AC VOLTMETER, DE450-011 0~120/240V
1
12
0601812598
RECEPTACLE, 5-20R
2
13
0601812592
RECEPTACLE, L5-20R
1
14
0601811035
RECEPTACLE, LS-30R
1
15
0601814010
RECEPTACLE, L14-20R
1
16
0021004010
MACHINE SCREW
8
16A
0207004000
HEX, NUT
8
17
0601830737
FULL POWER SWITCH, ET-330D12
1
18
0601831620
IDLE CONTROL SWITCH, C1550WA
1
19
0601831620
OPERATION SWITCH, C1550WA
1
20
0021004015
MACHINE SCREW
1
20A
0207004000
HEX, NUT
1
21
A3262800004
CAPACITOR ASSY., VR1H102MHA, 50V 1000µF 1
22
0017106016
HEX, HEAD BOLT
4
23
0017105010
HEX, HEAD BOLT
4
REMARKS
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 47
GA-3.6H Series— MUFFLER ASSY.
MUFFLER ASSY.
PAGE 48 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— MUFFLER ASSY.
MUFFLER ASSY.
NO
PART NO
1
7912310003
2
18320ZB4000
3
18325ZB4000
4
18329ZB4000
5
18355ZB4630
6
90183671003
7
0017106012
8
18333ZB4800
9
957000802000
10
7915461004
11
0017108020
12
7915460004
13
0017108025
13A
0207008000
14
0017108020
15
7915469004
16
0017106020
17
0017106012
PART NAME
QTY.
REMARKS
MUFFLER
1
PROTECTOR ......................... 1 ......... REPLACES P/N 0602302001
PROTECTOR ......................... 1 ......... REPLACES P/N 0602302002
SEAL ..................................... 2 ......... REPLACES P/N 0602302003
ARRESTOR, SPARK ............. 1 ......... REPLACES P/N 0602313060
TAPPING SCREW ................. 1 ......... REPLACES P/N 0602322060
BOLT HEX HEAD
5
GASKET ................................ 1 ......... REPLACES P/N 0602320175
HEX HEAD BOLT .................. 2 ......... REPLACES P/N 0602322061
BRACKET
1
BOLT HEX HEAD
1
BRACKET
1
BOLT HEX HEAD
2
HEX NUT
2
BOLT HEX HEAD
1
BRACKET
1
BOLT HEX HEAD
1
BOLT HEX HEAD
4
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 49
GA-3.6H Series — PIPE FRAME ASSY. (GA-3HZ)
PIPE FRAME ASSY. (GA3.6HZ)
PAGE 50 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series — PIPE FRAME ASSY. (GA-3HZ)
PIPE FRAME ASSY. (GA3.6HZ)
NO
PART NO
PART NAME
1
7915412002
PIPE FRAME
2
7915415004
BRACKET
3
0017106016
HEX. HEAD BOLT
4
7915443003
BASE
5
7895419004
RUBBER SUSPENSION
6
0207008000
HEX. NUT
7
1725419214
RUBBER SUSPENSION
8
0207008000
HEX. NUT
9
0017108040
HEX. HEAD BOLT
10
0017108040
HEX. HEAD BOLT
0207008000
HEX. NUT
11
7915455103
COVER
12
7915455003
COVER
13
0017106016
HEX. HEAD BOLT
14
7905512002
FUEL TANK
15
0810106004
CAP,FUEL TANK
16
0810107103
FUEL FILTER
17
0602125031
FUEL GAUGE
18
7855525514
RUBBER CUSHION
19
7855525604
GCOLLAR
20
0017108030
HEX. HEAD BOLT
21
0017108020
HEX. HEAD BOLT
22
0605511087
FUEL COCK
23
0605513140
HOSE
24
0605515096
HOSE BAND
QTY.
1
1
4
1
2
4
2
4
2
2
2
1
1
6
1
1
1
1
2
2
2
2
1
REMARKS
1
2
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 51
GA-3.6H Series— PIPE FRAME ASSY. (GA-3.6H/GA3.6HA)
PIPE FRAME ASSY. (GA3.6H/GA3.6HA)
PAGE 52 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
GA-3.6H Series— PIPE FRAME ASSY. (GA-3.6H/GA3.6HA)
PIPE FRAME ASSY. (GA3.6H/GA3.6HA)
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
A3417000002
PIPE FRAME ............................... 1 ................GA-3.6H ONLY
1
A3417000202
PIPE FRAME ............................... 1 ................GA-3.6HA ONLY
2
A3417100004
BRACKET
1
3
0017106016
HEX, HEAD BOLT
4
4
7915443003
BASE
1
5
7895419004
RUBBER SUSPENSION
2
6
1725419214
RUBBER SUSPENSION
2
7
0207008000
HEX, NUT
8
8
0017108030
HEX, HEAD BOLT
2
9
0017108040
HEX, HEAD BOLT
2
9A
0207008000
HEX, NUT
2
10
7905512002
FUEL TANK
1
11
A9924800014
CAP, FUEL TANK
1
12
A9924800004
FUEL FILTER
1
13
0602125034
FUEL GAUGE
1
14
16950ZB4015
FUEL STRAINER ......................... 1 ................REPLACES P/N 0605510068
14-1 16952ZB4005
SCREEN SET, HONDA ................ 1 ................REPLACES P/N 0605510069
15
950014521040
HOSE, HONDA ............................. 1 ................REPLACES P/N 0605513146
16
9500202080
HOSE BAND, HONDA .................. 2 ................REPLACES P/N 0605515178
17
7855525514
RUBBER CUSHION
2
18
7855525604
COLLAR
2
19
011208030
BOLT HEX HEAD
2
20
0017108020
BOLT HEX HEAD
2
21
A9117200103
HANGER
1
22
0601850097
STOPPER, 30029
1
23
0021008025
MACHINE SCREW
1
23A
0207008000
HEX, NUT
1
24
A931110004
PLASTIC WASHER ...................... 2 ................GA-3.6H
24
0601851116
PLASTIC WASHER ...................... 2 ................GA-3.6HA
25
0011308025
HEX, HEAD BOLT
2
25A
0037908000
HEX, NUT
2
25B
0042108000
PLAIN WASHER
2
26
0019206016
HEX, HEAD BOLT
1
27
7915455103
COVER
1
28
7855455003
COVER
1
29
0017106016
HEX, HEAD BOLT
6
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 53
HONDA GX240K1EDN2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 54 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
PART NO.
1
15721ZB4000
2
17211899000
3
17212ZB4003
4
17220ZB4003
5
17222ZC2000
6
17231899000
7
17235899000
8
17236899000
9
17252899000
10
17367413690
11
9405005000
12
9405006000
PART NAME
TUBE BREATHER
ELEMENT, AIR CLEANER
SEPARATOR, AIR CLEANER
HOUSING, AIR CLEANER
STAY, AIR CLEANER
COVER, AIR CLEANER
CLIP A, AIR CLEANER WIRE
CLIP B, AIR CLEANER WIRE
SEAL, AIR CLEANER
FILTER, DRAIN TUBE
NUT, FLANGE (5MM)
NUT, FLANGE (6MM)
QTY.
1
1
1
1
1
1
2
2
1
1
6
3
REMARKS
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 55
HONDA GX240K1EDN2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 56 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
PART NO.
1
14100ZE2W00
1
14100ZE2W01
1
14100ZE2306
2
3
4
5
6
*
7
8
9
10
11
14410ZE2013
14431ZE2010
14441ZE2000
14451ZE1013
14568ZE1000
14711ZE2000
14721ZE2000
14751ZE2003
14771ZE2000
14773ZE2000
PART NAME
QTY.
REMARKS
CAMSHAFT ASSY. ................................... 1 ............. INCLUDES ITEMS/W USE UP TO
*
.................................................................................. S/N 3620688
CAMSHAFT ASSY. ................................... 1 ............. INCLUDES ITEMS/W USE FROM
*
.................................................................................. S/N 3620689
CAMSHAFT ASSY. ................................... 1 ............. INCLUDES ITEMS/W USE UP TO
*
.................................................................................. S/N 4730487
ROD, PUSH
2
ARM, VALVE ROCKER
2
LIFTER, VALVE
2
PIVOT, ROCKER ARM
2
SPRING, WEIGHT RETURN
1
VALVE, IN.
1
VALVE, EX.
1
SPRING, VALVE
2
RETAINER, IN. VALVE SPRING
1
RETAINER, EX. VALVE SPRING
1
12
13
14
15
16
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
12209ZE8003
ROTATOR, VALVE
1
PLATE, PUSH ROD GUIDE
1
BOLT, PIVOT (8MM)
2
NUT, PIVOT ADJ.
2
SEAL, VALVE STEM ................................. 1 ............. USE FROM S/N 3620689
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 57
HONDA GX240K1EDN2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 58 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
1
16010ZE3701
2*
16011ZA0931
3*
16013ZA0931
4*
16015ZA0931
5*
16016ZH7W01
6*
16024124760
7*
16028ZA0931
8*
16100ZE2F01
9
16124ZE0005
10*
16148141881
11*
16166ZE2015
12*
16172ZE3W10
13*
16211ZE2700
14
16221ZA0800
15
16223ZA0800
16
16230ZE3701
17*
16260ZE2722
18#
16261ZE2702
19#
16262ZE2711
20#
16263ZA0000
21#
16264ZE2701
22#
16265ZE2721
23#
16268ZE2721
24
16269ZA0800
25#
16400ZE2703
26#
16611ZE2711
27#
16613893000
28#
16615893000
29
36135ZF6D41
30#
53149964003
31
88911MJ3000
32#
90431ZE2700
33#
90432ZE2700
34#
90433ZE2700
35#
90434ZE2700
36
90650SD9003
37#
93500050120A
38
938920501208
39
9405006000
40#
9410305000
41#
9454002010
42#
9454004010
43#
9454007010
44
9500202070
45
950053500810M
46
950053500810M
47
99101ZH80750
47
99101ZH80780
47
99101ZH80800
48*
99204ZE00450
*
PART NAME
QTY. REMARKS
GASKET SET
1
VALVE SET, FLOAT
1
FLOAT SET
1
CHAMBER SET, FLOAT
1
SCREW SET
1
SCREW SET, DRAIN
1
SCREW SET B
1
CARBURETOR ASSY. (BE72C) ............................ 1 ........ INCLUDES ITEMS W/
*
SCREW, THROTTLE STOP
1
CAP, CHOKE LEVER DUST
1
NOZZLE, MAIN
1
COLLAR, SET
1
INSULATOR, CARBURETOR
1
GASKET, CARBURETOR
1
GASKET, INSULATOR
1
VALVE ASSY., SOLENOID
1
STAY ASSY., MANUAL CHOKE ............................ 1 ........ INCLUDES ITEMS W/#
STAY, SOLENOID
1
LEVER, CHOKE
1
JOINT, ROD
1
ROD, CHOKE
1
STOPPER, CHOKE ROD
1
SPRING, MANUAL CHOKE
1
GASKET, AIR CLEANER
2
DIAPHRAGM ASSY.
1
ROD, CHOKE CONTROL
1
GROMMET, CHOKE ROD
1
GUIDE, CHOKE ROD
1
VALVE, DASHPOT CHECK
1
BUSH, ARM PIVOT
1
GROMMET, FENDER
1
WASHER, CHOKE LEVER
1
SEAL, CHOKE LEVER
2
WASHER, THRUST (2.7X8)
1
COLLAR, LEVER
1
CLIP, WIRE HARNESS
1
SCREW, PAN (5X12)
2
SCREW, WASHER (5X12)
2
NUT, FLANGE (6MM)
2
WASHER, PLAIN (5MM)
1
E-RING (2MM)
1
E-RING (4MM)
1
E-RING (7MM)
1
CLIP, TUBE (B7)
4
BULK HOSE, VACUUM (3.5X8000) (3.5X75)
1
BULK HOSE, VACUUM (3.5X8000) (3.5X130)
1
JET, MAIN (#75) (OPTIONAL)
1
JET, MAIN (#78) (OPTIONAL)
1
JET, MAIN (#80)
1
JET SET, PILOT (#45)
1
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 59
HONDA GX240K1EDN2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 60 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
PART NO.
1
16550ZE2700
3
16555ZE2000
4
16561ZE2000
5
16562ZE2700
9
16570ZE2701
19
* 16584883300
23
90013883000
24
90015ZE5010
93500050350A
30
* 9405006000
33
PART NAME
QTY.
REMARKS
ARM, GOVERNOR
1
ROD, GOVERNOR
1
SPRING, GOVERNOR
1
SPRING, THROTTLE RETURN
1
CONTROL ASSY. ................................................ 1 ... INCLUDES ITEMS W/
*
SPRING, CONTROL ADJUSTING
1
BOLT, FLANGE (6X12) (CT200)
2
BOLT, GOVERNOR ARM
1
SCREW, PAN (5X35)
1
NUT, FLANGE (6MM)
1
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 61
HONDA GX240K1EDN2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 62 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
2
11381ZE2801
GASKET, CASE COVER
1
3
11300ZE2000
COVER ASSY., CRANKCASE (S-TYPE) ............ 1 ........ INCLUDES ITEMS W/ USE UP TO
*
........................................................................................ S/N 4211335
3
11300ZE2020
COVER ASSY., CRANKCASE ............................ 1 ........ INCLUDES ITEMS W/
*
4
15600ZG4003
CAP ASSY., OIL FILLER .................................... 1 ........ INCLUDES ITEMS W/%
6
15600735003
CAP ASSY., OIL FILLER
1
INCLUDES ITEMS W/+
8%+
15625ZE1003
GASKET, OIL FILLER CAP
2
10
GOVERNOR ASSY. ............................................. 1 ........ INCLUDES ITEMS W/#
* 16510ZE2000
11 # 16511ZE2000
WEIGHT, GOVERNOR
2
*
12 # 16512ZE2000
HOLDER, GOVERNOR WEIGHT
1
*
PIN, GOVERNOR WEIGHT
2
13 # 16513ZE2000
* 16531ZE2000
14
SLIDER, GOVERNOR ......................................... 1 ........ USE UP TO S/N 4211335
* 16531Z0A000
SLIDER, GOVERNOR
1
14
*
15
WASHER, (6X6) .................................................. 1 ........ USE UP FROM S/N 4211336
* 90473147000
16
90602ZE1000
CLIP, GOVERNOR HOLDER
1
*
17
90701HC4000
PIN, DOWEL (8X12)
2
18
9410106800
WASHER, PLAIN (6MM)
1
* 957010803500 BOLT, FLANGE (8X35)
19
7
22
BEARING, RADIAL BALL (6206)
1
* 961006202000
25
92102ZE3004
OIL SEAL (35X52X8)
1
*
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 63
HONDA GX240K1EDN2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 64 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
PART NO.
9
961006206000
10
13310ZE2701
16
90741ZE2000
PART NAME
BEARING, RADIAL BALL (6206)
CRANKSHAFT (E-TYPE)
KEY, SPECIAL WOODRUFF (25X18)
QTY.
1
1
1
REMARKS
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 65
HONDA GX240K1EDN2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 66 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
PART NO.
1
12000ZE2815
2
15510ZE2043
3
16541ZE2010
4
31161ZE2000
5
90013883000
6
90131896650
7
90446KE1000
8
9410912000
10
91201890003
*
12
91353671003
13
9405010000
14
9425110000
15
957010601200
17
90013883000
18
34150ZH7003
19
06111ZE2408
PART NAME
QTY. REMARKS
CYLINDER ASSY. (ALERT) ................................. 1 ........ INCLUDES ITEMS W/
*
SWITCH ASSY., OIL LEVEL
1
SHAFT, GOVERNOR ARM
1
WIRE, GROUND
1
BOLT, FLANGE (6X12) (CT200)
1
BOLT, DRAIN PLUG
2
WASHER (8.2X17X0.8)
1
WASHER DRAIN PLUG 12 MM
1
OIL SEAL (30X46X8)
1
O-RING (13.5X1.5) (ARAI)
1
NUT, FLANGE (10 MM)
1
PIN, LOCK (10 MM)
1
BOLT FLANGE (6X12)
2
BOLT FLANGE (6X12) ......................................... 2 ........ USE FROM ENGINE S/N 3684579
ALERT UNIT, OIL ................................................ 1 ........ USE FROM ENGINE S/N 3684579
GASKET KIT ....................................................... 1 ........ USE UP TO S/N 4045100
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 67
HONDA GX240K1EDN2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 68 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
1
12200ZH9405
2
12204ZE2306
3
* 12205ZE2305
12216ZE2300
4
*
5
12251ZE2800
6
12310ZE2020
8
14775ZE2010
11
90014ZE2000
12
90042ZE2700
13
90047ZE2000
13
92900080320E
14
90441ZE2010
15
9430112200
18
957011008000
19
9807955846
19
9807955855
PART NAME
QTY. REMARKS
CYLINDER HEAD ................................................ 1 ........ INCLUDES ITEMS W/
*
GUIDE, VALVE (OS) (OPTIONAL)
1
GUIDE, EX. VALVE (OS) (OPTIONAL)
1
CLIP, VALVE GUIDE
1
GASKET, CYLINDER HEAD
1
COVER, HEAD
1
SEAT, VALVE SPRING
1
BOLT, HEAD COVER
1
BOLT, STUD (8X98)
2
BOLT, STUD ........................................................ 2 ........ USE UP TO S/N 3844352
BOLT, STUD (8X32)
2
WASHER, HEAD COVER
1
PIN A, DOWEL (12X20)
2
BOLT, FLANGE (10X80)
4
SPARK PLUG (BPR5ES) (NGK) (OPTIONAL) 1
SPARK PLUG (W16EPR-U) (DENSO)
1
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 69
HONDA GX240K1EDN2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 70 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
PART NO.
2
19610ZE2700ZD
3
19631ZE2D00
6
81329567020
7
90013883000
8
90654SA4003
PART NAME
COVER, FAN *NH1* (BLACK)
SHROUD
GROMMET, DRAIN HOLE
BOLT, FLANGE (6X12) (CT200)
CLIP, WIRE HARNESS (6MM) (WHITE)
QTY.
1
1
1
6
2
REMARKS
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 71
HONDA GX240K1EDN2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 72 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
PART NO.
2
19511ZE2000
5
28451ZE2W01
10
31100ZE2812
13
90201ZE3790
13
90201ZE3V00
PART NAME
QTY. REMARKS
FAN, COOLING
1
PULLEY STARTER
1
FLYWHEEL, LAMP
1
NUT, SPECIAL 16MM ......................................... 1 ........ USE UP TO S/N 3467138
NUT, SPECIAL 16MM ......................................... 1 ........ USE FROM TO S/N 3467139
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 73
HONDA GX240K1EDN2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 74 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
PART NO.
1
30500ZF6W02
2
30700ZE1013
3
31510ZE1811
4
31510ZE3003
6
31511ZE2000
7
31512ZE2000
10
36101ZE2701
11
36103ZE1000
12
90015883000
13
90013883000
PART NAME
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
COIL ASSY., LAMP (12V/25W)
COIL ASSY., LAMP (12V/25W)
CLAMP, WIRE
GROMMET, WIRE
WIRE, STOP SWITCH (470MM)
HOLDER, STOP SWITCH WIRE
BOLT, FLANGE (6X28)
BOLT, FLANGE (6X12) (CT200)
QTY.
1
1
1
1
1
1
1
1
6
1
REMARKS
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 75
HONDA GX240K1EDN2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 76 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO.
PART NO.
1
13010ZE2013
1
13011ZE2013
1
13012ZE2013
1
13013ZE2013
2
13101ZE2W00
2
13102ZE2W00
2
13103ZE2W00
2
13104ZE2W00
3
13111ZF6000
4
13200ZE2010
5
90001ZE8000
* 90551ZE1000
6
PART NAME
QTY. REMARKS
RING SET, PISTON (STD) .................................. 1 ........ USE UP TO S/N 4081304
RING SET, PISTON (OS 0.25, OPTIONAL) ........ 1 ........ USE UP TO S/N 4081304
RING SET, PISTON (OS 0.50, OPTIONAL) ........ 1 ........ USE UP TO S/N 4081304
RING SET, PISTON (0.75, OPTIONAL) .............. 1 ........ USE UP TO S/N 4081304
PISTON (STD)
1
PISTON (OS 0.25, OPTIONAL)
1
PISTON (OS 0.50, OPTIONAL)
1
PISTON (OS 0.75, OPTIONAL)
1
PIN, PISTON
1
ROD ASSY., CONNECTING (STD) ..................... 1 ........ INCLUDES ITEMS W/
*
BOLT, CONNECTING ROD
2
CLIP, PISTON PIN (18MM)
2
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 77
HONDA GX240K1EDN2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 78 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
1
28400ZE2W01ZB
2
28410ZE2W01ZB
*
3
* 28421ZE2W01
4
* 28422ZE2W01
5
28441ZE2W01
*
6
* 28442ZE2W01
7
28443ZE2W01
*
8
* 28444ZE2W01
9
* 28445ZE2W01
10
28461ZE2W02
*
11
* 28462ZE2W01
11
* 28462ZE2W11
12
28469ZE2W01
*
13
90004ZE2W01
* 90008ZE2003
14
PART NAME
QTY. REMARKS
STARTER ASSY., RECOIL *NH1* (BLACK) ........ 1 ........ INCLUDES ITEMS W/
*
CASE, RECOIL STARTER *NH1* (BLACK)
1
PULLEY, RECOIL STARTER
1
RATCHET, STARTER
2
SPRING, FRICTION
1
SPRING, STARTER RETURN
1
SPRING, RATCHET
2
RETAINER, SPRING
1
HOLDER, SPRING
1
GRIP, STARTER
1
ROPE, RECOIL STARTER
1
USE UP TO S/N 3793540
ROPE, RECOIL STARTER
1
USE FROM S/N 3793541
GRIP, REINFORCEMENT ................................... 1 ........ USE UP TO S/N 3793540
SCREW, CENTER
1
BOLT, FLANGE (6X10)
3
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 79
HONDA GX240K1EDN2 ENGINE — SOLENOID ASSY.
SOLENOID ASSY.
PAGE 80 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — SOLENOID ASSY.
SOLENOID ASSY.
NO.
PART NO.
1
* 16252ZA1010
16268893000
2
*
3
16270ZB4010
4
16271ZB4000
*
5
* 16273ZB4000
6
* 36160ZB4003
7
90013883000
*
8
* 91502ZB4701
9
* 93500050080A
9454004018
10
*
PART NAME
QTY.
REMARKS
CAP, CHOKE LEVER
1
SPRING, CHOKE RETURN
1
AUTO-THROTTLE ................................................ 1 ............. INCLUDES ITEMS W/
*
STAY, SOLENOID THROTTLE
1
LEVER, SOLENOID THROTTLE
1
SOLENOID ASSY.
1
BOLT, FLANGE (6X12) (CT200)
1
BUSH, AUTO-THROTTLE LEVER
1
SCREW, PAN (5X8)
2
E-RING 4MM
1
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 81
HONDA GX240K1EDN2 ENGINE — LABELS ASSY.
LABELS ASSY.
PAGE 82 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
HONDA GX240K1EDN2 ENGINE — LABELS ASSY.
LABELS ASSY.
NO.
PART NO.
1
87521ZE2W01
4
87528898620
6
87533ZC0630
10
87594ZB4A00
PART NAME
EMBLEM
MARK, CHOKE
MARK, AIR CLEANER
MARK, OIL CAUTION
QTY.
1
1
1
1
REMARKS
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 83
TERMS AND CONDITIONS OF SALE — PARTS
Effective: October 1, 2002
PAYMENT TERMS
5.
Parts must be in new and resalable condition, in the original Multiquip package (if
any), and with Multiquip part numbers
clearly marked.
6.
The following items are not returnable:
Terms of payment for parts are net 10 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a signed
manifest has been obtained from the carrier,
and any claim for shortage or damage must be
settled between the consignee and the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being replaced by another item, it is obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were purchased more than six months prior to
the return date.
MINIMUM ORDER
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original Equipment Manufacturer accounts who
use our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the invoice
for special handling including bus shipments,
insured parcel post or in cases where Multiquip
must personally deliver the parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
RETURNED GOODS POLICY
d. Special order items.
Return shipments will be accepted and credit
will be allowed, subject to the following provisions:
e. Electrical components.
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of the
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental damages.
f. Paint, chemicals, and lubricants.
LIMITATION OF WARRANTIES
g. Decals and paper products.
1.
h. Items purchased in kits.
No warranties, express or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not manufactured by Multiquip. Such warranties made in
connection with the sale of new, complete units
are made exclusively by a statement of warranty packaged with such units, and Multiquip
neither assumes nor authorizes any person to
assume for it any other obligation or liability
whatever in connection with the sale of its
products. Apart from such written statement of
warranty, there are no warranties, express,
implied or statutory, which extend beyond the
description of the products on the face hereof.
The minimum charge for orders from Multiquip is $15.00 net. Customers will be asked
for instructions regarding handling of orders
not meeting this requirement.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers, quantities, and descriptions of the items to be
returned.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
c. The list must state the reason(s) for
the return.
d. The list must reference the sales
order(s) or invoice(s) under which the
items were originally purchased.
e. The list must include the name and
phone number of the person requesting the RMA.
3.
A copy of the Return Material Authorization must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
c. Any line item with an extended dealer
net price of less than $5.00.
7.
The sender will be notified of any material
received that is not acceptable.
8.
Such material will be held for five working
days from notification, pending instructions. If a reply is not received within five
days, the material will be returned to the
sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific date and all orders received on or after that
date will be billed at the revised price. Rebates
for price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
PAGE 84 — GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05)
NOTE PAGE
GA-3.6H SERIES A.C. GENERATORS — OPERATION & PARTS MANUAL — REV. #0 (11/01/05) — PAGE 85
OPERATION & PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Tel. (800) 421-1244
Carson, CA 90746
Fax (800) 537-3927
Contact: mq@multiquip.com
Mayco Parts
800-306-2926
Fax: 800-672-7877
310-537-3700
Fax: 310-637-3284
Service Department
800-421-1244
Fax: 310-537-4259
310-537-3700
MQ Parts Department
800-427-1244
310-537-3700
MEXICO
UNITED KINGDOM
MQ Cipsa
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: pmastretta@cipsa.com.mx
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Fax: 800-672-7877
Fax: 310-637-3284
Warranty Department
800-421-1244, Ext. 279 Fax: 310-537-1173
310-537-3700, Ext. 279
Technial Assistance
800-478-1244
Fax: 310-631-5032
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Lancashire OL7 0TL
Contact: sales@multiquip.co.uk
Tel: 0161 339 2223
Fax: 0161 339 3226
CANADA
BRAZIL
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Multiquip
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro
Fax: 011-55-21-3433-9055
Contact: cnavarro@multiquip.com.br, srentes@multiquip.com.br
Tel: (450) 625-2244
Fax: (450) 625-8664
© COPYRIGHT 2005, MULTIQUIP INC.
Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the
property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the 3.6H Series Generators.
Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the
right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is: