advertisement
AWUS036AC IEEE 802.11ac AC1200
USB Wireless Adapter
User’s Guide
802.11ac USB Wireless Adapte r
AWUS036AC
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1.
Reorient or relocate the receiving antenna.
2.
3.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4.
Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, (Example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions:
(1) This device may not cause harmful interference.
(2)
This Device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment.
In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
CE mark Warning
This is a class B device, in a domestic environment; this product may cause radio interference, in which case the user may be required to take adequate measures.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE
EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive
98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment)
As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria Belgium,
Denmark, Finland, and France (with Frequency channel restrictions). Germany, Greece,
Ireland, Italy, Luxembourg .The Netherlands, Portugal, Spain, Sweden and United
Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states Iceland,
Liechtenstein, Norway and Switzerland.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
Contents
4.1 General Page……………………………………………….……………………………….…………..16
4.2 Advanced Page………………………………………………………………………………………….17
4.3 Statistics Page……………………………………………………………………………………..……..18
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
1.
Introduction
Thank you for your purchase of the wireless adapter. Featuring wireless technology, this wireless networking solution has been designed for both large and small businesses, and it is scalable so that you can easily add more users and new network features depending on your business scale.
SYSTEM REQUIREMENTS
Windows System: XP 32/64, Vista 32/64, Win7 32/64,Win 8 32/64
PCs must have a device driver installed. It allows you to communicate with wireless adapter.
BEFORE YOU START
1. Contents confirmation
USB AC1200 wireless adapter
2x dual-band, high-sensitivity antennas
USB docking stand
Warning card
Driver CD
2. Connect your wireless adapter to your PC after the driver installation.
3. LED
LED turns on when the wireless adapter linking normally.
LED is blinking when WLAN Adapter is active.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
2.
Driver Installation
2.1
Windows 7
Notes: The following installation was operated under Windows 7. (Procedures are similar for
Windows XP /vista)
Step 1:
Insert the installation CD into your CD-ROM.
Installation program will prompt language setup.
Choose the Setup Language you would like to use and click Next button
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
Step 2:
Welcome Installation dialog prompt shown.
Click Next to continue.
Click Cancel to close installation. Installing and configuring WLAN utility.
Step 3:
Click Install
ALFA Network Inc.
Step 4:
Click Finish to complete installation.
802.11ac USB Wireless Adapte r
AWUS036AC
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
3.
Wireless Network Configuration
The management software is provided for the wireless adapter.
When you insert the WLAN Adapter into your laptop or desktop, an icon should appear in the
Windows System Tray automatically.
3.1
Utility Icon
Client mode utility running but no WLAN Adapter plugged.
Client mode utility running and WLAN Adapter scan available network.
Client mode utility running and WLAN Adapter can not scan any AP.
3.2
Client Mode
3.2.1
Wireless Device Control
Show Tray Icon – Show icon or not show icon in stray.
Radio Off – Stop wireless signal.
Disable Adapter – Stop wireless device.
Virtual WiFi allowed Windows operating system control switch
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
3.2.2
General Setting
Once device is set, double click on that icon and the configuration window will pop up as shown. It shows the current connected network. The signal strength and link quality are displayed also. The bar graph displays the quality and strength of the link between the node and its Access Point. Link Quality is a measurement of receiving and transmitting performances over the radio.
Network Address displays current MAC Address, IP Address, and Subnet, and Gateway.
Click Renew IP button to refresh IP address leased from wireless AP.
TX the POWER adjustable RF output power
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
3.2.3
Profile Setting
In profile tab, you can Add , Remove , Edit , Duplicate and Set Default to manipulate profile content manually. Strongly recommend to use profile after you do Available Network .
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
3.2.4
Available Network Setting
Click Available Network tab and it will show all available networks that radio can reaches.
Select proper SSID & BSSID you want to connect.
Click Refresh button to force and rescan available networks currently.
Select one of SSIDs, and click Add to Profile to create profile that can be configured more wireless parameters.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
In this page, you can edit your profile name; configure wireless security like WEP, WPA,
WPA2, 802.1x …etc. After finishing setup, click OK button to save configuration.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
3.2.5
Status
In this page, it shows all wireless, networking and device driver version in details.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
3.2.6
Wi-Fi Protected Setup
There is an easy and secure setup solution for Wi-Fi network. You can choose PIN Code or
Push Button method to connect to an AP.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
4.
Access Point Mode
4.1
General Page
This page provides general information of this AP, including name, MAC address and list of joined stations.
1. SSID: The name of this AP.
2. BSSID: Six two-digital numbers of the MAC address of this AP.
3. Association Table: It is the list of joined stations to this AP.
4. AID (Association ID):
The AID field is a value assigned by an AP during association that represents
16-bit ID of a station. It is a unique value assigned by AP.
5. MAC address:
It is the six two-digit numbers that assemble the MAC address of respected joined station.
6. Life Time:
It is the timer that counts down from 10 minutes whenever the AP connects the station successfully. If an STA associated to SW AP does not have any interaction with the AP in 10 minutes, it will be disassociated from the Infra-structure BSS.
7. Config: A dialog of this AP is shown for configuration modification.
8. ICS:
Internet Connection Sharing.
It enables this AP to create the domain to share this internet/intranet network connection.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
a. Network Name (SSID):
The name of the AP is searchable by other wireless nodes. The length of SSID should be shorter than 32 characters. b. Channel: Select the wireless channel within current channel plan. c. Network Authentication & Data Encryption :
Open System:
It is combined with data encryption type to be WEP or to be disabled. Disabled: you decide to open this AP to every one without network authentication. WEP: you decide to setup the basic data encryption with a defined network key.
Shared Key + WEP:
You decide to apply both authentication and data encryption to prevent unauthorized login.
WPA-PSK + TKIP & WPA2-PSK + TKIP:
The most advanced authentication and data encryption that provide the best security protection. d. ASCII / PASSPHRASE:
ASCII:
You should provide either 5 or 13 ASCII characters on Network key edit box.
PASSPHRASE: You could input words on Network
Key edit box:
64 bits: The generated pass key is 64-bit to be complied with data packets. 128 bits: The generated pass key is 128-bit to be complied with data packets.
Hexadecimal:
While both ASCII and PASSPHRASE are not checked, you should input hexadecimal number in the network key box. For example, 10 digits hex number for 64-bit WEP or 26 digits hex number for 128-bit WEP. e. Key index (advanced) (1 ~4):
At most four key index to represent the opposite network key.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
4.2
Advanced Page
Users could setup the advanced characteristics of network packet for transmission on this page.
1. Beacon Interval:
This filed indicates the interval between each beacon that this AP sends out in unit of TU (1024 micro-seconds).
2. DTIM Period:
The DTIM Period field is the number of Beacon intervals between successive
DTIMs.
3. Preamble Mode:
Long: higher quality but with lower performance than preamble short mode.
Short: Normal quality but with higher performance then preamble long mode.
Auto: select the proper preamble mode by current signal frame information.
ALFA Network Inc.
802.11ac USB Wireless Adapte r
AWUS036AC
4.3
Statistics Page
The Tx/Rx status of current wireless connection is shown. A statistic analysis of packet transition is listed.
ALFA Network Inc.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project