KT-LCD5 eBike Display User Manual

KT-LCD5 eBike Display User Manual
2.1 Turn on backlight and headlights
V1.0
Dear customer, please read this manual before you use KT-LCD5 instrument. The manual will guide
Hold
long to turn on backlight and headlights (the controller should
you use the instrument correctly to achieve a variety of vehicle control and vehicle status display.
have headlight drive output function); hold
Functions and Display
backlight and headlights.
long again to turn off the
2.2 Assist ratio gear (ASSIST) switch
Hold
or
shortly to switch 1-5 file gear. Gear 1 is for the
minimum power, gear 5 is for the highest power. Each startup will automatically
restore the gear shutdown last time(the user can set randomly). Gear 0 is
without booster function.
2.3 6Km/H assist promotion function
1
UP Button
2
SW Button
3
DOWN Button
4
Km/H
Riding speed(metric)
MPH
Riding speed (imperial)
MXS
MAX speed
Pas level
AVS
Average speed
Battery capacity indicator
Km
Distance(metric)
Mil
Distance (imperial)
DST
Trip distance
ASSIST
5
11
6
CRUISE
Cruise function
7
PAS
Power-assisted function
TM
Single trip time
ODO
Total distance
TTM
Total trip time
VOL
Battery voltage
THROTTLE
Throttle display
13
The brake display
6Km/H push power assist
14
Backlight and headlights
8
9
10
12
Hold
and
6Km /h. Release
flashes, the vehicle drives at the speed not more than
button, the function is invalid.
2.4 THROTTLE display
Turn on throttle, THROTTLE display.
2.5 PAS display
When Power-assisted riding, PAS display.
Operation
1.
ON/OFF
Hold
2.6 Cruise function
button long to turn on the power, and hold
long for a second time to turn off the
power. When the motor stops driving and when the e-bike is not used for a consecutive 5 minutes, it will
automatically shut down and turn off the motor power supply.
2. Display 1
After the cruise function is turned on, the trip riding speed is greater than
7 km/ h, hold
button to cancel.
2.7 Display and delete of single Data
Hold
button to start up and enter display 1.
long and enter cruise, the CRUISE lit. Brake or hold any
After power on for 5 seconds, hold
3.
and
The wheel diameter will be set after finishing setting the maximum riding
at the same time,
single trip riding time (TM) and single trip distance (DST) flash, hold
speed, wheel diameter specifications flashes. Hold
button shortly, the content of both is cleared. If failed holding the button
the specifications of wheel diameter. Select the range 6,8,10,12,14,16,18,20,22,
within 5 seconds, it will automatically return the display interface after 5
24,26,700c and 28 inches. Hold
seconds, original content is preserved.
parameter settings.
Display 2
3.
or
shortly to set
button shortly and go to the next
Set the metric units
The metric units will be set after finishing setting wheel diameter, Km/H
Hold
button shortly in display 1 to enter display 2. In the riding
and Km flash. Hold
mode after 5 seconds, display 2 automatically returns to display 1.
4.
Display 3
Hold
5.
In display 3, hold
6.
Hold
or
shortly and select the three metric units of
speed, mileage, and ambient temperature in synchronization.
Display
Metric
Imperial
Riding speed
Km/H
MPH
Total distance
Km
Mil
button shortly in display 2 to enter display 3. In the riding
condition, five seconds later, a single maximum speed (MXS) display
4. Km/H and Km stop flash after metric unit setting is completed. Hold
automatically returns to the real riding speed (Km/H).
re-enter the maximum riding speed setting interface; or hold
button long to exit from setting
environment of routine projects and save the setting values, returning to display 1.
button shortly (SW),and the display will re-enter display 1.
5. Exit from routine project setting
button to turn off the display and the power supply of controller.
7. Automatically prompt interface
7.1 Error Code Display
button shortly again to
All three routine project settings can exit from the setting environment and return to the display
Error Code
Definition
if hold
button long after each setting is completed, meanwhile the setting values are saved.
Under each setting interface, if the button failed holding for more than 1 minute, it will
01＿info
Throttle Abnormality
03＿info
Motor hall signal Abnormality
automatically return to display 1, and the setting value is invalid.
04＿info
Torque sensor signal Abnormality
Outline Drawings and Dimensions
05＿info
Axis speed sensor Abnormality(only applied to torque sensor)
1.
06＿info
Motor or controller has short circuit Abnormality
Dimensions of main instrument body
Electronic control system failure will display (flashing) fault code. Once the fault was removed, it
automatically exits from the fault code display interface.
General Project Setting
1.
Set maximum riding speed
After power on for 5 seconds, hold
and
maximum riding speed Km/H and MXS flash, hold
the maximum riding speed (default 25Km/H). Hold
at the same time,
or
2. Wiring diagram
shortly to set
button shortly and
go to the next parameter settings.
2.
Wheel diameter setting
Prepared by Suzhou Kunteng Electronics Co., Ltd.