LUPUS-Electronics GEODOME LE335 User guide
Add to My manuals
48 Pages
LUPUS-Electronics GEODOME LE335 is a high-end surveillance camera with the latest chip from SONY delivering professional quality and maximum performance in all lighting conditions. Its excellent backlight compensation and advanced Hyper-Dynamic functions make it suitable for even the most challenging lighting conditions. The novel housing enables wall, ceiling mounting, and installation in suspended ceilings for a professional and discreet appearance.
advertisement
GEODOME®
LE335
Benutzerhandbuch
User Manual
Inhalt
LENS: MANUAL /AUTO. ............................................................................ 14
SHUTTER/AGC: AUTO / MANUAL. ........................................................... 14
BACKLIGHT: BLC / HLC / OFF................................................................... 16
/ DAY / B/W. ............................................................ 17
CAMERA ID: ON / OFF. ............................................................................ 20
2
1. Einführung
Vielen Dank für den Kauf der GEODOME ® Kamera. Bevor Sie die Kamera in
Betrieb nehmen, lesen Sie sich die folgenden Sicherheits- und
Installationshinweise sorgfältig durch.
Bewahren Sie das Handbuch sorgfältig auf um im Nachhinein offene Fragen klären zu können. Die Beschreibungen, Bilder und Technischen Daten können sich im Sinne des technischen Fortschritts ändern.
Diese Kamera ist für den Innen- und Außeneinsatz geeignet.
WICHTIGER HINWEIS
2. Hinweise
Besonders bei diesem GEODOME Modell müssen Sie auf die
Sicherheitshinweise achten. Falls Sie sich mit der Installation einer Solchen nicht auskennen, kontaktieren Sie einen Elektronik-fachmann.
Bitte lesen Sie diese Anleitung vor der Benutzung des Gerätes vollständig, bewahren Sie die Anleitung auf und geben Sie sie weiter, wenn Sie das Gerät an andere Personen übergeben.
Das Blitzsymbol in einem Dreieck, weist auf die Gefahr eines elektrischen
Schlags hin. Öffnen Sie niemals das Kameragehäuse oder das Gehäuse des mitgelieferten Netzteils
3
2.1 WARNUNG:
UM DIE GEFAHR EINES STROMSCHLAGES ZU VERRINGERN, FÜHREN SIE
DIE INSTALLATION NIEMALS IM FREIEN BEI NÄSSE DURCH.
INSTALLATION:
"DIE INSTALLATION DER KAMERA SOLLTE NUR VON QUALIFIZIERTEN
FACHKRÄFTEN VORGENOMMEN WERDEN."
2.2 Hinweise zur Benutzung und Installation:
Diese Kamera ist eine hochwertige Überwachungskamera in wettersicherer Ausführung. Beachten
Sie unbedingt folgende Sicherheitshinweise.
• Richten Sie die Kamera nicht direkt in die Sonne
• Richten Sie die Kamera nie direkt in ein Spotlicht
• Behandeln Sie die Kamera behutsam, starke Vibrationen oder Stöße können die
Kamera beschädigen.
• Berühren Sie niemals Interne-Bauteile, die Kamera könnte beschädigt werden.
• Installieren Sie die Kamera nicht in der Nähe von starken elektrischen Leitungen. Dies könnte die Bildqualität beeinträchtigen.
• Installieren Sie die Kamera nicht direkt auf einen Aluminium oder Eisenmast ohne den
Fuß der Kamera mit einer Gummierung von dem Mast zu isolieren. Das Kamerabild könnte gestört werden.
• Beachten Sie die max. Feuchtigkeits- und Temperaturbedingungen.
• Dieses Gerät ist nicht dafür bestimmt, durch Personen (einschließlich Kinder) mit eingeschränkten physischen, sensorischen oder geistigen Fähigkeiten oder mangels
Erfahrung und/oder mangels Wissen benutzt zu werden, es sei denn, sie werden durch eine für ihre Sicherheit zuständige Person beaufsichtigt oder erhielten von ihr
Anweisungen, wie das Gerät zu benutzen ist. Kinder sollten beaufsichtigt werden, um sicherzustellen, dass sie nicht mit dem Gerät spielen. ·
• Die Kamera enthält Kabel, die zu Strangulierungen führen und kleine Teile, die verschluckt werden können. Montieren Sie die Kamera so, dass sie von Kindern nicht erreicht werden kann. Lassen Sie Verpackungsmaterialien nicht achtlos liegen, diese können für spielende Kinder zu einer Gefahr werden.
Sollten Sie Fehler feststellen
Falls Fehler auftreten sollten, ziehen Sie den Strom der Kamera und kontaktieren Sie Ihren
Lieferanten. Weitere Benutzung erhöht die Gefahr eines Brands oder eines elektrischen Schlags.
Bestimmungsgemäßer Einsatz
Die Kamera ist für die allgemeine Videoüberwachung im Tag- und Nachteinsatz vorgesehen. Sie ist im Innen- und Außenbereich einsetzbar. Bei Installation und Einsatz ist darauf zu achten, dass
Persönlichkeitsrechte von Personen nicht verletzt werden. Eine Überwachung von Personen ohne deren Wissen und Einverständnis ist nicht zulässig. Ein anderer Einsatz als in dieser
4
Bedienungsanleitung beschrieben ist nicht zulässig und führt zu Gewährleistungs- und
Garantieverlust sowie zu Haftungsausschluss. Dies gilt auch für Veränderungen und Umbauten.
Entsorgungshinweise:
Gerät nicht im Hausmüll entsorgen!
Dieses Gerät entspricht der EU-Richtlinie über Elektronik- und Elektro-Altgeräte
Altgeräteverordnung) und darf daher nicht im Hausmüll entsorgt werden. Entsorgen Sie das Gerät über Ihre kommunale Sammelstelle für Elektronik-Altgeräte!
3 Beschreibung:
Technik der neuen Generation: mit dieser High-End Überwachungskamera mit dem neusten Chip aus dem Hause SONY gehen Sie keine Kompromisse ein. Professionelle Qualität und maximale
Performance egal wie das Licht gerade spielt. Selbst bei Lichtverhältnissen bei denen das menschliche Auge die Umgebung nicht mehr oder nur kaum wahrnimmt überträgt diese
Überwachungskamera noch hervorragende Bilder. Durch exzellente Gegenlichtkompensation und erweitere Hyper-Dynamic Funktionen wird auch starkes Gegenlicht unproblematisch. Das neuartige
Gehäuse ermöglicht Wand-, Deckenmontage sowie die Installation in abgehängten Decken für ein besonders professionelles und unauffälliges Erscheinungsbild.
4 Highlights:
High Resolution Exzellente Sensitivität
Der neue Sony Exview HAD II CCD liefert Hohe Sensitivität, geringe Streifen- bildung,
650-700TVL mit extreme guten brilliante Antispiegelung und hohe S/N Rate.
LUX-Werten. Der Effio-E DSP von Sony sorgt für einen starken Gegenlichausgleich
Adaptive Tone Reproduction (ATR)
Der neuartige Effio-E DSP von Sony liefert die neue ATR-Funktion. ATR ist eine einfach abtastende WDR Funktion; auch bekannt als Digital WDR oder Software WDR.
Digital Noise Reduction (DNR)
Wenn Sie 2DNR aktivieren, kann die
Rauschentwicklung im Bild extrem reduziert werden. Dies sorgt für extrem klare Bilder auch bei schlechten Lichtverhältnissen.
5
Tag & Nacht
Der mechanische IR-Cut Filter sorgt für perfekte Bilder am Tag sowie unter IR-Licht in der Nacht.
High Light Compensation (HLC)
HLC verbessert das Bild bei starkem
Gegenlicht. Zu helle Bereiche werden abgedunkelt und zu dunkle Bereiche
Privatzonenmaskierung
Insgesamt 8 Bereiche stehen Ihnen zur aufgehellt.
Bewegungserkennung
Die kameraseitige Bewegungs- erkennung
Verfügung um sensible Zonen zu ermöglicht eine noch bessere Kontrolle. verdecken. Löst die Kamera Bewegung aus, wird dies im Bild durch Kästchenbildungen signalisiert. So lässt sich die rekorderseitige
Aufnahmeauslösewahrscheinlichkeit verbessern
Linse
Eingebaute DC-Vario-Fokal Linse mit mechanischem IR-Cut Filter
OSD
OSD (On Screen Display) Einstellungen-Menu.
OSD-Funktionsumfang
Folgende Funktionen können über das OSD eingestellt werden: AES (Automatic Electronic
Shutter = Verschlusszeit), AI (Auto Iris = Linse), GC (Gain Control = Verstärkerregelung), WB
(White Balance = Weißabgleich), BLC (Back Light compensation = Gegenlichtkompensation), positive/ negative und Horizontal Mirror (Spiegelung).
6
5. Lieferumfang:
Bitte prüfen Sie gleich nach Erhalt, ob die Lieferung vollständig und unversehrt ist.
Item Description Item Picture QTY
Kamera 1
Plastiktüte
Schrauben
Schraube für
Gehäusesicherung
Benutzerhandbuch
7
1
4
1
1
5.1 Beschreibung der einzelnen Bauteile
Um Einstellungen am OSD-Menu bzw. an Kamerafunktionen vorzunehmen, öffnen Sie bitte das Plastik Dome-Gehäuse. Hierzu müssen Sie zunächst die seitlich angebrachte
Sicherungsschraube lösen (Camera Lock).
1~3.OSD Knöpfe (Menu):
Nr. Name Funktion
1
2
3
4
5
LEFT
ENTER
DOWN
RIGHT
UP
LINKS
Öffnet das MENU / ENTER
RUNTER
RECHTS
HOCH
8
6. Installation
1. Entfernen Sie den Domekamera-Kuppel
Lösen Sie die seitliche Sicherheitsschraube und drehen Sie dann die Kuppel gegen den
Uhrzeigersinn auf.
2. Blickwinkel einstellen
Sie können die Kamera in 3 Richtungen justieren: Hoch, Runter, Vertikal
Die Basis lässt sich 60° zu beiden Seiten und 120° im Ganzen ausrichten (PAN).
Senkrecht können Sie die Kamera 120° bewegen (TILT)
Der Fuß kann 360° bewegt werden.
9
3. Den Blickwinkel der Kamera einstellen
Drehen Sie die Schraube für den Zoom etwas locker (gegen den Uhrzeigersinn).
Bewegen Sie dann den Hebel seitlich nach links oder rechts um den Zoom der
Kamera zu verändert.
Lockern Sie den Hebel für die Schärfe (Focal Adjustment) und stellen Sie mit diesem das Kamerabild scharf.
Ist der gewünschte Blickwinkel und die max. Schärfe erreicht, stellen Sie die Hebel wieder fest.
4. Digitale Kamerafunktionen einstellen
1
IR
LED-Anschluss
(nicht belegt)
3
STROM/VIDEO
(KAMERA)
5 DATEN
2
OSD
KONTROLLE
4
POWER/VIDEO
(DC/BNC)
10
5. Kuppel schließen
Sind alle nötigen Einstellungen gemacht, kann die Kuppel wieder geschlossen werden.
The black plastic inner liner has a cutout slot for viewing.
Drehen Sie die Kuppel im Uhrzeigersinn bis sie einrastet.
Ist die Kuppel verschlossen, drehen Sie die Platik-Abdeckung so, dass die Linse der
Kamera nicht verdeckt wird.
11
6. Kamerasicherung
Um zu verhindern, dass die Kamera einfach von unbefugten geöffnet werden kann, drehen Sie die Sicherungsschraube wieder wie abgebildet ein:
7. Anschluss
Verbinden Sie das Videokabel mit einem geeigneten 75 Ohm BNC-Koaxialkabel und das
Stromkabel mit dem mitgelieferten DC 12V Netzteil.
12
7.1 Das OSD MENU
LENS
SHUTTER/ AGC
WHITE BAL
BACKLIGHT
ATR
NR
PICT ADJUST
NEXT
↲
EXIT
↲ SAVE ALL
OSD Setup Menu page 1
AUTO
↲
AUTO
↲
ATW
OFF
OFF
↲
↲
OSD Setup Menu page 2
DAY/ NIGHT
PRIVACY
MOTION DET
CAMERA ID
LANGUAGE
CAMERA RESET
BACK
↲
EXIT
↲ SAVE ALL
AUTO*
OFF
OFF
OFF
ENGLISH
Hauptmenu Einstellungen
• Um das Hauptmenu anzuzeigen drücken Sie den MENU Knopf. Das Hauptmenu hat 2 Seiten
(siehe oben)
• Drücken Sie HOCH / RUNTER um das gewünschte Untermenu anzuwählen.
• Drücken Sie RECHTS / LINKS um einen Wert zu verändern
• Drücken Sie MENU um das Fenster zu schließen.
13
7.2 OSD Hauptmenu Beschreibung
7.2.1 LENS: MANUAL /AUTO wählbar.
LENS: MAUNAL
Keine weiteren Einstellungsmöglichkeiten
LENS: AUTO
AUTO
TYPE
:DC
MODE
:AUTO/ OPEN /CLOSE
SPEED
:000~255
AUTO:
OPEN:
CLOSE:
SPEED:
Die Kamera stellt die Linse automatisch ein.
Linse voll geöffnet.
Linse ganz geschlossen.
Geschwindigkeit der Linse.
7.2.2 SHUTTER/AGC: AUTO / MANUAL wählbar.
SHUTTER/AGC: AUTO
AUTO
HIGH LUMINANCE
MODE
:SHUT+AUTO IRIS / AUTO IRIS / SHUT
BRIGHTNESS
:000~255
LOW LUMINANCE
MODE
:AGC / OFF
BRIGHTNESS
:x0.25、x0.50、x0.75、x1.00
HIGH LUMINANCE
Wenn LENS auf AUTO steht:
SHUT+AUTO IRIS: Die Belichtung wird durch den Automatischen Verschluß (auto electronic shutter) kombiniert mit der Auto-Iris gesteuert.
AUTO IRIS: Die Belichtung wird nur durch die Auto-Iris gesteuert.
Wenn LENS auf Manual steht:
SHUT: Die Belichtung wird durch den Elektronischen Verschluß gesteuer (electronic shutter).
LOW LUMINANCE
Einstellung für minimale Lichtverhältnisse (AGC minimal).
14
SHUTTER/AGC: MANUAL
MANUAL
SHUTTER: Feste elektronische Verschlusszeit.
AGC: Feste AGC Gain Kontrolle.
7.2.3 WHITE BAL
ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH LOCK wählbar.
WHITE BAL.: ATW
SPEED
:000~255
ATW
DELAY CNT
:000~255
ATW FRAME
:x0.50、x1.00、x1.50、x2.00
ENVIRONMENT
:INDOOR、OUTDOOR
MODE
:SHUT+AGC
SHUTTER
:
NTSC
:1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000
PAL
:1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000
AGC
:6.00、12.00、18.00、24.00、30.00、36.00、42.00、44.80
SPEED
:ATW Speed = ATW Geschwindigkeit
DELAY CNT
: ATW Verzögerungszeit
ATW FRAME
: ATW Bildspanne
ENVIRONMENT
:
ATW Einsatzumgebung
WHITE BAL.: PUSH
Erkennt die momentane Farbtemperatur und speichert diesen Wert ab.
WHITE BAL.: USER1
B-GAIN
:000~255
USER1
R-GAIN
:000~255
WHITE BAL.: USER2
USER2
B-GAIN
:000~255
R-GAIN
:000~255
WHITE BAL.: MANUAL
MANUAL LEVEL
:19~54
WHITE BAL.: ANTI CR
Diese Funktion kann Probleme bei „rollenden Farben“ beheben. Diese Funktioniert wie CRS (Color Rolling Support).
WHITE BAL.: PUSH LOCK
Erkennt die momentane Farbtemperatur und speichert diesen Wert ab.
15
7.2.4 BACKLIGHT: BLC / HLC / OFF wählbar.
BACKLIGHT.: BLC
Aktiviert die BLC-Funktion (Gegenlichtausgleich).
BACKLIGHT.: HLC
Aktiviert die High Light Kompensation.
7.2.5 ATR: ON / OFF wählbar.
ATR.: ON
LUMINANCE
CONTRAST
LOW
、MID、HIGH
LOW
、MIDLOW、MID、MIDHIGH、HIGH
LUMINANCE
: Stellt das Ausmaß der Helligkeitskompression ein.
CONTRAST
: Stellt den Bildkontrast des ATR-Bildvergleichs ein.
HINWEIS: Aktivieren Sie niemals BLC und ATR gleichzeitig. ATR sollte bei schwierigen
Lichtverhältnissen aktiviert werden (zB. Objekte vor hellem Hintergrund).
7.2.6 DNR:
↲
NR MODE
Y LEVEL
Y/C
、Y、C、OFF
000~015
C LEVEL 000~015
NR MODE
:
Stellt die Rauschunterdrückung (DNR) auf Y/C, Y oder C.
Y LEVEL
:
Verändert die Stärke des Y-Filters.
C LEVEL
:
Verändert die Stärke des C-Filters
HINWEIS: Der Y/C Modus ist der automatische DNR Modus.
7.2.7 PICT ADJUST:
↲
MIRROR ON / OFF
BRIGHTNESS
CONTRAST
SHARPNESS
HUE
GAIN
000~255
000~255
000~255
000~255
000~255
Verändern Sie hier Werte für Spiegelung, Helligkeit, Kontrast, Schärfe, HUE und GAIN.
16
7.2.8 NEXT:
↲
Öffnet die 2. Seite des Hauptmenus
7.2.9 EXIT:
↲
Schließt das OSD Menu.
7.2.10 SAVE ALL:
Speichert alle Änderungen ohne das Menu zu schließen.
7.2.11 DAY/NIGHT
:AUTO / DAY / B/W wählbar.
DAY/NIGHT: AUTO
BURST
:ON/OFF
AUTO
DELAY CNT
:000~255
DAY NIGHT :000~255
NIGHT DAY :000~255
BURST
:Gibt beim Umschalten in den Nacht-Modus ein Signalstoß aus.
DELAY CNT
:Verzögerungszeit in Sekunden bis zur Umschaltung in den Tag- bzw.
Nachtmodus
DAY NIGHT :Schwellenwert zur Identifikation des Nachtstatus vom Tagstatus. Je größer die Zahl desto später wird in den Nachtmodus geschaltet und desto früher vom Nachtmodus in den
Tagmodus.
NIGHT DAY: Schwellenwert zur Identifikation des Tagstatus vom Nachtstatus. Je größer die
Zahl desto früher wird vom Nachtmodus in den Tagmodus geschaltet und ebenso später vom Tag- in den Nachtmodus.
DAY/NIGHT: DAY
Ausschließlich Tagmodus (IRCUT deaktiviert)
DAY/NIGHT: NIGHT
Ausschließlich Nachtmodus
Night BURST
:ON/OFF
BURST
:Gibt beim Umschalten in den Nacht-Modus ein Signalstoß aus.
17
7.2.12 PRIVACY: ON / OFF wählbar.
PRIVACY: ON
AREA SEL Max. 8
TOP
BOTTOM
LEFT
RIGHT
COLOR
TRANSP
MOSAIC
000~288(PAL)
000~288(PAL)
650TVL
: 000~468 (PAL)
650TVL
:000~468 (PAL)
1~8
0.00 / 0.50 / 0.75 / 1.00
ON / OFF
AREA SEL: Zeigt eine von 8 wählbaren Masken an. Alle darunter angegebenen
Einstellungen betreffen nur diese Maske
HINWEIS: Wurde die MONITOR AREA im MOTION DET Menu aktiviert, stehen Ihnen nur noch statt 8 Masken für die Privatzonenmaskierung zur Verfügung.
TOP
:
Geben Sie die Höhe der Maskierung an
BOTTOM: Geben Sie das untere Ende der Maskierung an
LEFT: Geben Sie den Anfang von Links der Maskierung an
RIGHT
: Geben Sie das Rechte Ende der Maskierung an
COLOR
: Wählen Sie die Farbe von allen Maskierungen
TRANSP
:Wählen Sie die Transparenz aller Maskierungen.
MOSAIC
:Aktivieren oder Deaktivieren Sie die Mosaik – Funktion.
18
7.2.13 MOTION: ON / OFF wählbar.
MOTION DET: ON
DETECT SENSE 000~127
BLOCK DISP
MONITOR AREA
AREA SEL
TOP
BOTTOM
LEFT
RIGHT
ON / OFF / ENABLE
ON / OFF
1~4
000~244 (NTSC) / 000~288(PAL)
000~244 (NTSC) / 000~288(PAL)
550TVL
:000~378 (NTSC)、000~370 (PAL)
650TVL
:000~474 (NTSC)、000~468 (PAL)
550TVL
:000~378 (NTSC)、000~370 (PAL)
650TVL
:000~474 (NTSC)、000~468 (PAL)
DETECT SENSE: Wählen Sie die Sensitivität.
BLOCK DISP: Aktivieren oder Deaktivieren Sie die Blockdarstellung. Halten Sie
MENU gedrückt um diese zu verlassen.
MONITOR AREA: Geben Sie an, ob Monitoring-Fenster angezeigt werden sollen.
AREA SEL:
TOP:
BOTTOM:
LEFT:
RIGHT:
Wählen Sie das zu ändernde Monitoring-Fenster.
Geben Sie die Höhe des Monitoring-Fensters an
Geben Sie das untere Ende des Monitoring-Fensters an
Geben Sie den linken Anfang des Monitoring-Fensters an
Geben Sie das rechte Ende des Monitoring-Fensters an
19
7.2.14 CAMERA ID: ON / OFF wählbar.
A B C D E F G H I J K L M N O P Q R
S T U V
W X Y Z 0 1 2 3 4 5 6 7 8 9 - ! ” # $ %
& ’
( ) _
‵ , ¥ : ; < = > ? @ \ ^ * . x +
Alle darstellbaren Zeichen
/
← → ↑ ↓
Verwenden Sie die unteren Symbole
←, →, ↑ oder ↓ um den
Cursor in die entsprechende Richtung zu bewegen
CLR
POS
Wurde ein Zeichen angewählt kann dieses mit der Taste CLR gelöscht werden
Wählen Sie POS an und drücken Sie ENTER um den
Kameranamen im Bild zu positionieren. Drücken Sie MENU um zurückzukehren.
7.2.15 SPRACHE
Das OSD unterstützt 8 Sprachen: Englisch / Japanisch / Deutsch / Französisch /
Russisch / Portugiesisch / Spanisch / Chinesisch
7.2.16 CAMERA RESET
Stellt alle Werkseinstellungen wieder her.
7.2.17 BACK
Kehren Sie zum Hauptmenu, Seite 1 zurück.
20
8. Technische Daten
Bild Sensor
Effektive Pixel
Horizontale Auflösung
Minimale Lichtverhältnisse
Tag Nachtumschaltung
S/N Wert
Verschlusszeit (einstellbar)
Linse
Automatische Iris Kontrolle
Gain Kontrolle
Weißabgleich
ATR
DNR
Gegenlichtkompensation
High Light Kompensation
Privatsphärenmaskierung
Bewegungserkennung
Kamera ID
Spiegelung
Positiv/ Negativ
Video Ausgang
Stromversorgung
Stromverbrauch
Betriebstemperaturen
Gamma Charakteristik
System
Maße (BxT)
1/3” Color CCD Ex-View HAD II
(Sony Chipset)
NTSC: 976x494
PAL: 976x582
Day: 650 TVL
Night: 700 TVL
0.01ux/ F1.2 (Tag)
Ab unter 5 Lux einstellbar
Mehr als 48dB (AGC Aus)
PAL:1/50~1/100,000
Asphärisches Varioobjektiv mit ICR (IR-Cut)
DC gesteuert
Auto/ Manuell
ATW / PUSH / USER1 / USER2 / ANTI CR / Manuell /
PUSH LOCK
AN/ AUS
AN/ AUS
AN/ AUS
AN/ AUS
Maximal 8 Bereiche
4 Bereiche
Bis 52 Zeichen
AN/ AUS
AN/AUS
1Vp-p/ 75 Ohms
DC 12V±10%
120mA max.
-10° ~ 50°C (14 bis 122
℉)
0.45
INT
37 mm x35 mm (OSD Platte)
HINWEIS: Das Design und die technischen Daten können sich im Sinne des
technischen Fortschritts ändern. Irrtümer vorbehalten.
21
22
23
LUPUS-Electronics
®
GmbH
Lise-Meitner-Str.20, D-76829 Landau
Tel. +49 (0) 6341 93 55 3 0 Fax. +49 (0) 6341 93 55 3 20
E-Mail: [email protected] www.Lupus-Electronics.de
24
LUPUSNIGHT®
LE335
User Manual
Inhalt
ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH LOCK selectable. ............... 14
2
1. INTRODUCTION
Thank you for your purchase of your brand new GEODOME®-LE335 Camera.
Please read the manual carefully before the first activation and keep it at a safe place for further usage. The documentation, images and technical specifications are subject to change. The camera is suitable for both in- and outdoor use.
2. USAGE AND INSTALLATION NOTE
IMPORTANT NOTICE
It is vital to comply with the safety instructions before and while using this
GEODOME camera. If you are unable to install the device yourself, please seek help from a professional installer.
Please read the manual carefully before the first activation and keep it at a safe place for further usage or in case of giving the device to third persons.
The flash symbol in a triangle indicates danger of electric shock. Never open the camera housing or the housing of the supplied power adapter.
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT CARRY OUT
INSTALLATION OUTDOORS UNDER WET CONDITIONS.
THE INSTALLATION OF THE DEVICE SHALL ONLY BE CARRIED OUT BY
QUALIFIED PERSONNEL.
3
This camera is a weather proof high quality video surveillance camera. Please note the following safety instructions:
• Do not focus the camera to the sun.
• Do not focus the camera to a spotlight.
• Handle the camera carefully and protect it from strong vibrations or hits.
• Do not touch internal components or wiring
• Do not install the camera close to strong electrical currents which could undermine its image quality.
• Do not attach the camera to an aluminium or iron surface without insulating it from the surface.
• Always comply with max. humidity and temperature conditions.
• This device must not be operated by persons with physical, sensorical or mental disabilities or persons with limited experience or knowledge unless these persons are supervised by a person specifically assigned to care for their safety. The devise shall under no circumstances be operated by children.
• The camera contains wiring which may lead to strangulation or small items which may be swallowed. Please keep the camera, its packaging and associated items away from children.
In case of malfunction
In case of malfunction, please pull the powerplug and contact your dealer.
Further usage may increase the risk of fire or electric shock.
Intended usage
The camera is intended for conventional video surveillance by day and night. It is designed for both in- and outdoor use. Please make sure that privacy rights of third persons be not infringed at any time. The surveillance of persons without their explicit knowledge and consent is prohibited by law in many countries.
This product must not be used for any other purpose save those set out in the user manual. Contravention may lead to loss of warranty and guarantee as well as the exclusion of liability. This includes changes to and modifications of the product.
Orderly disposal:
Do not dispose of this product with your domestic waste!
This device complies with the EU regulation on electronic waste and therefore must not be diposed of with domestic waste. Please dispose of this product with your local waste disposal for electronic devices.
4
3. FEATURES
Clear image quality has been achieved by employing a 1/3” Hi-Res. CCD, which provides a horizontal resolution of 650 TV lines. The camera can be by External
Light Sensor; it provides Color image in full light condition (Day) and provides B/W image in low light condition (Night) to reach the best effect. High performance: providing unique ATR (Adaptive Tone Reproduction), DNR (Digital Noise
Reduction), HLC (High Light Compensation), CRS (Color Rolling Support),
Privacy function, Mirror function, as well as manually adjusting picture quality functions (Such as Contrast/Sharpness/Color etc.).
High Resolution
CCD Sensor provides high resolution reaching 650~700 TVL with advanced and clear picture quality.
Excellent Sensitivity
High sensitivity, low smear, high anti-blooming and high S/N ratio.
Adaptive Tone Reproduction (ATR)
ATR is the Single Scan WDR function; it has the other name with Digital
WDR, Software WDR. perfectly shows the image details between dark and light. Newly added environment dynamic detection switch, enhancing
WDR image efficiency.
Digital Noise Reduction (DNR)
With 2DNR enable, it can reduce the noise to produce extremely clear picture quality even under low light condition.
Day & Night
Mechanic IR Cut-Filter driving unit with
Light Sensor.
High Light Compensation (HLC)
By setting mask are, the user will experience better operation convenience see a clearer image.
Privacy Mask
Privacy image masking with free position, support up to 8 areas of privacy masking zone.
Lens (External manual focus)
Built-in DC-type Vari-Focal lens with
ICR / Without ICR.
Motion Detection
Camera-site takes the initiative in providing motion detection alert for a more comprehensive monitoring and careful editing of motion detection area. When there are changes within the detection area, the camera immediately issues a warning.
OSD
OSD (On Screen Display) Setup
Menu. Camera tile setup of up to 16 alphanumeric letters.
5
Mechanism
Weatherproofing Housing Design.
Application
All function can be operated from OSD: AES (Automatic Electronic Shutter), AI
(Auto Iris), GC (Gain Control), WB (White Balance), BLC (Back Light compensation), positive/ negative and Horizontal Mirror.
4. PACKING LIST
Check to make sure all of the items shown below are included in your product package. If something is missing, contact your dealer as soon as possible.
Item Description Item Picture QTY
Camera & Bracket 1
Appurtenances
Fix retaining screw
Countersunk Head
Screws for Camera
Protection
Instruction Manual
6
1
4
1
1
5. NAME and FUNCTION of EACH PART
To adjust the OSD, remove the dome cover from the main body by gently turning the cover counter-clockwise to unlock and pull free from the main body. The OSD buttons are can be found on the main body of the dome camera.
1~3.OSD Button (Menu):
No. Name
1
2
3
4
5
LEFT
ENTER
DOWN
RIGHT
UP
Function
LEFT
Get in MENU and ENTER
DOWN
RIGHT
UP
7
6. INSTALLATION
6.1 Camera Installation & Operation
1. Removing the Dome Cover
Remove the dome cover from the main body by gently turning the cover counter-clockwise to unlock and pull free from the main body.
2. Camera Image Adjustment
You can adjust camera to any direction by using Pan, Tilt, and Rotate mechanism.
Pan Base moves by 60° to each side direction and 120° on the whole.
Tilt Base covers total 120° angle (60° to each side).
Angle range of Rotate Base is 360°.
3. Adjusting the Vari-Focal Lens
Loosen the Zoom lever counter-clockwise a little, and then rotate the
Zoom lever to obtain the best image view.
Loosen the Focus lever counter-clockwise a little, and then rotate the
Focus lever to obtain the optimum picture quality.
Re-tighten the Zoom lever and Focus lever after adjustment.
8
2
4. Adjusting the Function Control Board
1
IR BOARD
WEFER
3
POWER/VIDEO
(CAMERA)
OSD KEY 4
POWER/VIDEO
(DC/BNC)
9
5 DAY IN
5. Attaching the Dome Cover
After all necessary adjustment has been made reinstall the dome cover to the main body.
The black plastic inner liner has a cutout slot for viewing.
Reinstall the dome cover and the main body by turning the dome clockwise until it locks in place.
10
The dome comes with a black plastic inner liner placed within the dome cover. Therefore, after replacing the dome cover rotate the liner so that the cutout slot (hole for viewing) is in the correct position and not blocking the camera lens.
6. Camera Protection
To prevent unpredictable damage and burglary, lock-up the dome by using the countersunk head screw.
7. Wiring Instructions
Connect the video output to the monitor or other video device through a
75 Ohms type coaxial cable and the DC-Jack or AC/ DC-Terminator to the power source.
Note: Power adapter is sold separately.
11
7. OPERATION
7.1 OSD Framework
Main Menu Display
OSD Setup Menu page 1
LENS
SHUTTER/ AGC
WHITE BAL
BACKLIGHT
ATR
NR
PICT ADJUST
NEXT
↲
EXIT
↲ SAVE ALL
AUTO
↲
AUTO
↲
ATW
OFF
OFF
↲
↲
OSD Setup Menu page 2
DAY/ NIGHT
PRIVACY
MOTION DET
CAMERA ID
LANGUAGE
CAMERA RESET
BACK
↲
EXIT
↲ SAVE ALL
Main Menu Setup
AUTO*
OFF
OFF
OFF
ENGLISH
• In order to display the setup menu on the screen, set the menu command or press the button panel.
• Use UP/ DOWN control buttons to select each item.
• Use LEFT/ RIGHT control buttons to change the data.
•
•
Use MENU control button to ENTER/ EXIT the menu display.
↲=ENTER
*NOTE: LE335 is comming without IR-LED‘s
12
7.2 OSD Main Menu Description
7.2.1 LENS: MANUAL /AUTO selectable.
LENS: MAUNAL
Not adjustment
LENS: AUTO
TYPE
:DC
AUTO MODE
:AUTO/ OPEN /CLOSE
SPEED
:000~255
AUTO:
OPEN:
CLOSE:
SPEED:
Camera automatically controls the lens.
Lens fully open.
Lens fully closed.
Speed of the lens.
7.2.2 SHUTTER/AGC: AUTO / MANUAL selectable.
SHUTTER/AGC: AUTO
AUTO
HIGH LUMINANCE
MODE
:SHUT+AUTO IRIS / AUTO IRIS / SHUT
BRIGHTNESS
:000~255
LOW LUMINANCE
MODE
:AGC / OFF
BRIGHTNESS
:x0.25、x0.50、x0.75、x1.00
HIGH LUMINANCE
When LENS is setup to AUTO mode
SHUT+AUTO IRIS: Exposure is controlled by auto electronic shutter combined with auto iris.
AUTO IRIS: Exposure controlled by auto iris.
When LENS is setup to Manual mode
SHUT: Exposure controlled by electronic shutter.
LOW LUMINANCE
Setup low lux environment, minimum AGC level.
13
SHUTTER/AGC: MANUAL
MANUAL
MODE
:SHUT+AGC
SHUTTER
:
NTSC
:1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000,
1/10000
PAL
:1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000
AGC
:6.00、12.00、18.00、24.00、30.00、36.00、42.00、44
.80
SHUTTER: Fixed electronic shutter speed.
AGC: Fixed AGC gain control.
7.2.3 WHITE BAL
ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH LOCK selectable.
WHITE BAL.: ATW
SPEED
:000~255
ATW
DELAY CNT
:000~255
ATW FRAME
:x0.50、x1.00、x1.50、x2.00
ENVIRONMENT
:INDOOR、OUTDOOR
SPEED
:ATW Speed
DELAY CNT
: ATW Delay Time
ATW FRAME
:
ATW Frame Range Setup
ENVIRONMENT
:
WHITE BAL.: PUSH
The function will keep detecting the Color Temperature, and then it will keep saving the parameter to camera.
WHITE BAL.: USER1
USER1
B-GAIN
:000~255
R-GAIN
:000~255
WHITE BAL.: USER2
USER2
B-GAIN
:000~255
R-GAIN
:000~255
WHITE BAL.: MANUAL
MANUAL LEVEL
:19~54
WHITE BAL.: ANTI CR
The function can reduce the color rolling issue, and it is the same with CRS (Color Rolling Support) function.
WHITE BAL.: PUSH LOCK
14
The function will detect the Color Temperature to save into the camera.
7.2.4 BACKLIGHT: BLC / HLC / OFF selectable.
BACKLIGHT.: BLC
Enable the function of Back Light Compensation, and the detection method is the BLC Smart.
BACKLIGHT.: HLC
Enable the function of High Light Compensation.
7.2.5 ATR: ON / OFF selectable.
ATR.: ON
LUMINANCE LOW
、MID、HIGH
CONTRAST LOW
、MIDLOW、MID、MIDHIGH、HIGH
LUMINANCE
: Set the extent of the luminance compression
CONTRAST
: Set the extent of the contrast enhancement.
NOTE: If you enable the ATR funciton, please avoid to enable the
BACKLIGHT function in the same time.
7.2.6 NR:
↲
NR MODE Y/C
、Y、C、OFF
Y LEVEL 000~015
C LEVEL 000~015
NR MODE
:
Y LEVEL
:
C LEVEL
:
Set the DNR mode of Y/C, Y and C.
Set the Y filter strength.
Set the C filter strength.
NOTE: The Y/C mode is the automanic DNR mode.
7.2.7 PICT ADJUST :
↲
MIRROR ON / OFF
BRIGHTNESS 000~255
CONTRAST 000~255
SHARPNESS 000~255
15
HUE 000~255
GAIN 000~255
Adjust all camera parameters here.
16
7.2.8 NEXT :
↲
Move to MAIN MENU, page 2
7.2.9 EXIT :
↲
Exit OSD to choose the list.
7.2.10 SAVE ALL :
When you change the OSD menu settings, before leaving the OSD item option SAVE ALL. Press ENTER key to change the memory settings for the OSD.
7.2.11 DAY/NIGHT:AUTO / DAY / B/W selectable.
DAY/NIGHT: AUTO
BURST
:ON/OFF
DELAY CNT
:000~255
AUTO
DAY NIGHT :000~255
NIGHT DAY :000~255
BURST
:Selects whether to output the burst signal when the Night status
DELAY CNT
:Set the Night/ Day identification transfer time.
DAY NIGHT :Set the threshold for identifying the Night status from the Day status.
NIGHT DAY :Set the threshold for identifying the Day status from the Night status.
DAY/NIGHT: DAY
Day mode forcibly
DAY/NIGHT: NIGHT
Night mode forcibly
Night BURST
:ON/OFF
BURST
:Selects whether to output the burst signal
17
7.2.12 PRIVACY: ON / OFF selectable.
PRIVACY: ON
AREA SEL Max. 8
TOP
BOTTOM
LEFT
RIGHT
COLOR
TRANSP
MOSAIC
000~244 (NTSC) / 000~288(PAL)
000~244 (NTSC) / 000~288(PAL)
550TVL
:000~378 (NTSC) 、000~370 (PAL)
650TVL
:000~474 (NTSC)、000~468 (PAL)
550TVL
:000~378 (NTSC)、000~370 (PAL)
650TVL
:000~474 (NTSC)、000~468 (PAL)
1~8
0.00 / 0.50 / 0.75 / 1.00
ON / OFF
AREA SEL
:
Select the mask frame to be adjusted.
NOTE: When the MONITOR AREA has been set to ON by the
MOTION DET setting, only 4 PRIVACY AREA SEL are selectable (1 / 4, 2 / 4, 3 / 4, 4 / 4).
TOP
:
BOTTOM
:
LEFT
:
RIGHT
:
COLOR
:
TRANSP
:
MOSAIC
:
Set the top side of the mask frame selected
Set the bottom side of the mask frame selected
Set the left side of the mask frame selected
Set the right side of the mask frame selected
Set the colors of the mask frames.
Set the transparency ratio of the mask frames.
Set the mask frame mosaic function to ON or OFF.
18
7.2.13 MOTION: ON / OFF selectable.
MOTION DET: ON
DETECT SENSE 000~127
BLOCK DISP ON / OFF / ENABLE
MONITOR AREA ON / OFF
AREA SEL
TOP
BOTTOM
LEFT
RIGHT
1~4
000~244 (NTSC) / 000~288(PAL)
000~244 (NTSC) / 000~288(PAL)
550TVL
:000~378 (NTSC)、000~370 (PAL)
650TVL
:000~474 (NTSC)、000~468 (PAL)
550TVL
:000~378 (NTSC)、000~370 (PAL)
650TVL
:000~474 (NTSC)、000~468 (PAL)
DETECT SENSE: Set the motion detection sensitivity.
BLOCK DISP: Control the ON/ OFF status of the motion detection block display.
MONITOR AREA: Set whether to use the monitoring frames.
AREA SEL:
TOP:
BOTTOM: selected
LEFT:
RIGHT:
Select the monitoring frame to be set.
Set the top side of the monitoring frame selected
Set the bottom side of the monitoring frame
Set the left side of the monitoring frame selected
Set the right side of the monitoring frame selected
19
7.2.14 CAMERA ID: ON / OFF selectable.
A B C D E F G H I J K L M N
O P Q R S T U V
W X Y Z 0 1 2 3 4 5 6 7 8 9 - !
” # $ % & ’
( ) _
‵ , ¥ : ; < = > ? @ \ ^ *
Each User Font
. x + /
← → ↑ ↓
The camera ID cursor moves in the direction of the arrow when the Enter operation input is performed from the status in which
←, →, ↑ or ↓ has been selected using the character selection cursor.
CLR
The character selected by the camera ID cursor is cleared when the Enter operation input is performed from the status in which CLR has been selected using the character selection cursor.
POS
The display switches to the camera ID display position setting screen when the Enter operation input is performed from the status in which POS has been selected using the character selection cursor. On the camera ID display position setting screen, the camera ID display position is changed in real time in response to the left, right, up or down operation input. When the Enter operation input is performed, the display position is entered, and the display returns to the camera ID setting screen.
7.2.15 LANGUAGE
There are 8 kind of language: English / Japanese / German / French /
Russian / Portuguese / Spanish / Simplified Chinese selectable.
7.2.16 CAMERA RESET
Reset Factory default setup.
7.2.17 BACK
Return to MAIN MENU, page1.
8.
SPECIFICATION
20
Note: Design and specifications are subject to change without prior notice.
Image Device
Effective Picture Elements
Horizontal Resolution
Minimum Illumination
Day to Night Illumination
S/N Ratio
1/3” Color CCD Ex-View HAD II
(Sony Chipset)
NTSC: 976x494
PAL: 976x582
Day: 650 TVL
Night: 700 TVL
0.01ux/ F1.2 (Day)
Under 5 Lux
More than 48dB (AGC OFF)
Shutter Speed Control
Lens Furnished
Auto Iris Control
Gain Control
White Balance
ATR
DNR
Back Light Compensation
High Light Compensation
PRIVACY
MOTION DET
Camera ID
Mirror
Positive/ Negative
Video Output
Power Supply
Power
Consumption
Vari-Focal Lens
Vari-Focal
Lens+IR
IR On
IR Off
Operating Temp.
Gamma Characteristic
Synchronous System
Dimensions (WxD)
NTSC:1/60~1/100,000, PAL:1/50~1/100,000
Vari-Focal Lens and Vari-Focal Lens with ICR
DC Driver
Auto/ Manual
ATW / PUSH / USER1 / USER2 / ANTI CR / Manual / PUSH
LOCK
ON/ OFF
ON/ OFF
ON/ OFF
ON/ OFF
Maximum 8 Areas
4 Areas
Up to 52 Characters
ON/ OFF
ON/OFF
1Vp-p/ 75 Ohms
DC 12V±10%
120mA max.
370mA max.
120mA max.
-10
℃ ~ 50 ℃ (14 to 122℉)
0.45
INT
32 mm x32 mm (Camera board)
37 mm x35 mm (OSD board)
21
22
23
LUPUS-Electronics
®
GmbH
Lise-Meitner-Str.20, D-76829 Landau
Tel. +49 (0) 6341 93 55 3 0 Fax. +49 (0) 6341 93 55 3 20
E-Mail: [email protected] www.Lupus-Electronics.de
24
advertisement
Related manuals
advertisement
Table of contents
- 3 1. Einführung
- 3 2. Hinweise
- 4 2.1 Warnungen
- 4 2.2 Hinweise zur Benutzung und Installation
- 5 Beschreibung
- 5 Highlights
- 7 5. Lieferumfang
- 8 5.1 Beschreibung der einzelnen Bauteile
- 9 6. Installation
- 13 7.1 Das OSD MENU
- 14 /AUTO
- 14 MANUAL
- 16 ADJUST
- 20 SPRACHE
- 20 RESET
- 21 Technische Daten
- 27 INTRODUCTION
- 27 2. USAGE AND INSTALLATION NOTE
- 29 3. FEATURES
- 30 4. PACKING LIST
- 31 5. NAME and FUNCTION of EACH PART
- 32 6. INSTALLATION
- 32 6.1 Camera Installation & Operation
- 36 7. OPERATION
- 36 7.1 OSD Framework
- 37 7.2 OSD Main Menu Description
- 37 7.2.1 LENS: MANUAL /AUTO selectable
- 37 7.2.2 SHUTTER/AGC: AUTO / MANUAL selectable
- 38 7.2.3 WHITE BAL
- 38 ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH LOCK selectable
- 39 7.2.4 BACKLIGHT: BLC / HLC / OFF selectable
- 39 7.2.5 ATR: ON / OFF selectable
- 41 7.2.10 SAVE ALL
- 41 7.2.11 DAY/NIGHT:AUTO / DAY / B/W selectable
- 42 7.2.12 PRIVACY: ON / OFF selectable
- 43 7.2.13 MOTION: ON / OFF selectable
- 44 7.2.14 CAMERA ID: ON / OFF selectable
- 44 7.2.15 LANGUAGE
- 44 7.2.16 CAMERA RESET
- 44 7.2.17 BACK
- 44 SPECIFICATION