advertisement
TC-FMCH-500 Hardware User Manual
TC-FMCH-500
Hardware User Manual
Rev.1.01
Rev.1.01
1
TC-FMCH-500 Hardware User Manual
Revision History
Version Date Description
Rev.1.00 2010/08/30 Release version
Rev.1.01 2012/03/13 Modified Figure 4-1
Publisher
Yoshioka
Yoshioka
Rev.1.01
2
TC-FMCH-500 Hardware User Manual
Table of Contents
1.
Related Documents and Accessories ......................................................................................... 8
2.
Overview ...................................................................................................................................... 8
3.
Feature ........................................................................................................................................ 8
4.
Cable Specification ...................................................................................................................... 8
4.1.
Cable block diagram .................................................................................................................. 8
4.2.
External View of the Cable ........................................................................................................ 9
4.3.
Signal connection .................................................................................................................... 10
5.
Appendix ..................................................................................................................................... 11
Rev.1.01
3
TC-FMCH-500 Hardware User Manual
List of Figures
Figure 4-1 Block Diagram .................................................................................................................. 8
Figure 4-2 Cable over view ................................................................................................................ 9
Figure 4-3 Cable end.......................................................................................................................... 9
Figure 5-1 Stacking Image ................................................................................................................ 11
Figure 5-2 Parallel use ...................................................................................................................... 11
Rev.1.01
4
TC-FMCH-500 Hardware User Manual
Introduction
Thank you for purchasing the TC-FMCH-500 board. Before using the product, be sure to carefully read this user manual and fully understand how to correctly use the product. First read through this manual, then always keep it handy.
SAFETY PRECAUTIONS
Be sure to observe these precautions
Observe the precautions listed below to prevent injuries to you or other personnel or damage to property.
Before using the product, read these safety precautions carefully to assure correct use.
These precautions contain serious safety instructions that must be observed.
After reading through this manual, be sure to always keep it handy.
The following conventions are used to indicate the possibility of injury/damage and classify precautions if the product is handled incorrectly.
Danger
Indicates the high possibility of serious injury or death if the product is handled incorrectly.
Warning
Indicates the possibility of serious injury or death if the product is handled incorrectly.
Caution
Indicates the possibility of injury or physical damage in connection with houses or household goods if the product is handled incorrectly.
The following graphical symbols are used to indicate and classify precautions in this manual.
(Examples)
Turn off the power switch.
Do not disassemble the product.
Do not attempt this.
!
Rev.1.01
5
!
!
!
!
!
!
!
TC-FMCH-500 Hardware User Manual
Warning
In the event of a failure, disconnect the power supply.
If the product is used as is, a fire or electric shock may occur. Disconnect the power supply immediately and contact our sales personnel for repair.
If an unpleasant smell or smoking occurs, disconnect the power supply.
If the product is used as is, a fire or electric shock may occur. Disconnect the power supply immediately. After verifying that no smoking is observed, contact our sales personnel for repair.
Do not disassemble, repair or modify the product.
Otherwise, a fire or electric shock may occur due to a short circuit or heat generation. For inspection, modification or repair, contact our sales personnel.
Do not touch a cooling fan.
As a cooling fan rotates in high speed, do not put your hand close to it. Otherwise, it may cause injury to persons. Never touch a rotating cooling fan.
Do not place the product on unstable locations.
Otherwise, it may drop or fall, resulting in injury to persons or failure.
If the product is dropped or damaged, do not use it as is.
Otherwise, a fire or electric shock may occur.
Do not touch the product with a metallic object.
Otherwise, a fire or electric shock may occur.
Do not place the product in dusty or humid locations or where water may splash.
Otherwise, a fire or electric shock may occur.
Do not get the product wet or touch it with a wet hand.
Otherwise, the product may break down or it may cause a fire, smoking or electric shock.
Do not touch a connector on the product (gold-plated portion).
Otherwise, the surface of a connector may be contaminated with sweat or skin oil, resulting in contact failure of a connector or it may cause a malfunction, fire or electric shock due to static electricity.
Rev.1.01
6
TC-FMCH-500 Hardware User Manual
Caution
!
Do not use or place the product in the following locations.
Humid and dusty locations
Airless locations such as closet or bookshelf
Locations which receive oily smoke or steam
Locations exposed to direct sunlight
Locations close to heating equipment
Closed inside of a car where the temperature becomes high
Staticky locations
Locations close to water or chemicals
Otherwise, a fire, electric shock, accident or deformation may occur due to a short circuit or heat generation.
!
Do not place heavy things on the product.
Otherwise, the product may be damaged.
■ Disclaimer
This product is a board intended for FMC interface function. Tokyo Electron Device Limited assumes no responsibility for any damages resulting from the use of this product for purposes other than those stated.
Even if the product is used properly, Tokyo Electron Device Limited assumes no responsibility for any damages caused by:
(1) Earthquake, thunder, natural disaster or fire resulting from the use beyond our responsibility, acts by a third party or other accidents, the customer
’s willful or accidental misuse or use under other abnormal conditions.
(2) Secondary impact arising from use of this product or its unusable state (business interruption or others)
(3) Use of this product against the instructions given in this manual.
(4) Malfunctions due to connection to other devices.
Tokyo Electron Device Limited assumes no responsibility or liability for:
(1) Erasure or corruption of data arising from use of this product.
(2) Any consequences or other abnormalities arising from use of this product, or
(3) Damage of this product not due to our responsibility or failure due to modification
This product has been developed by assuming its use for research, testing or evaluation. It is not authorized for use in any system or application that requires high reliability.
Repair of this product is carried out by replacing it on a chargeable basis, not repairing the faulty devices.
However, non-chargeable replacement is offered for initial failure if such notification is received within two weeks after delivery of the product.
The specification of this product is subject to change without prior notice.
The product is subject to discontinuation without prior notice.
Rev.1.01
7
TC-FMCH-500 Hardware User Manual
1. Related Documents and Accessories
Related documents:
All documents relating to this board can be downloaded from our website. Please see attached paper on the products.
2. Overview
TC-FMCH-500 is cable for FMC to FMC.
3. Feature
FMC(HPC) connector on each cable-end.
Cable length is 500mm
4. Cable Specification
4.1. Cable block diagram
Following figure shows block diagram of TC-FMCH-500
Figure 4-1 Block Diagram
Rev.1.01
8
TC-FMCH-500 Hardware User Manual
4.2. External View of the Cable
Figure 4-2 Cable over view
Rev.1.01
Figure 4-3 Cable end
9
TC-FMCH-500 Hardware User Manual
4.3. Signal connection
Following signals are connected each other but other signals are not connected.
Straight connection
・CLK0_M2C_P/CLK0_M2C_N/CLK1_M2C_P/CLK1_M2C_N
・LA**_P/LA**_N(** is 0∼33. Total 34pair = 68 single-end signals)
・GBTCLK0_M2C_P / GBTCLK0_M2C_N
・GBTCLK1_M2C_P / GBTCLK1_M2C_N
・GMD of ROW C, D, G, H.
・TCK,TDI,TDOTMS,TRST_L,GA0,GA1,SCL,SDA
Cross connection with AC coupling capacitor(0.1uF)
・DP0_C2M_P - DP0_M2C_P / DP0_C2M_N - DP0_M2C_N
・DP1_C2M_P - DP1_M2C_P / DP1_C2M_N - DP1_M2C_N
・DP2_C2M_P - DP2_M2C_P / DP2_C2M_N - DP2_M2C_N
・DP3_C2M_P - DP3_M2C_P / DP3_C2M_N - DP3_M2C_N
・DP4_C2M_P - DP4_M2C_P / DP4_C2M_N - DP4_M2C_N
・DP5_C2M_P - DP5_M2C_P / DP5_C2M_N - DP5_M2C_N
・DP6_C2M_P - DP6_M2C_P / DP6_C2M_N - DP6_M2C_N
・DP7_C2M_P - DP7_M2C_P / DP7_C2M_N - DP7_M2C_N
・DP8_C2M_P - DP8_M2C_P / DP8_C2M_N - DP8_M2C_N
・DP9_C2M_P - DP9_M2C_P / DP9_C2M_N - DP9_M2C_N
Rev.1.01
10
TC-FMCH-500 Hardware User Manual
5. Appendix
Following figures show how to use this cable.
Figure 5-1 Stacking Image
Figure 5-2 Parallel use
Rev.1.01
11
TC-FMCH-500 Hardware User Manual
Rev.1.01
PLD Solution Dept. PLD Division
URL:
http://solutions.inrevium.com/
E-mail: [email protected]
HEAD Quarter: Yokohama East Square, 1-4 Kinko-cho, Kanagawa-ku, Yokohama City,
Kanagawa, Japan 221-0056
TEL: +81-45-443-4016 FAX: +81-45-443-4058
12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement