Motherboard
H81M-V3
E8800
First Edition
April 2014
Copyright © 2014 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License (“GPL”),
under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software
Licenses. Such software in this product is distributed without any warranty to the extent permitted by the
applicable law. Copies of these licenses are included in this product.
Where the applicable license entitles you to the source code of such software and/or other additional data,
you may obtain it for a period of three years after our last shipment of the product, either
(1) for free by downloading it from http://support.asus.com/download
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location
where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source
code we would be much obliged if you give us a notification to the email address gpl@asus.com, stating
the product and describing the problem (please DO NOT send large attachments such as source code
archives, etc. to this email address).
2
Contents
Safety information........................................................................................................ 4
About this guide........................................................................................................... 4
Package contents......................................................................................................... 6
H81M-V3 specifications summary.............................................................................. 6
Chapter 1:
Product introduction
1.1
Before you proceed....................................................................................... 1-1
1.2
Motherboard overview.................................................................................. 1-2
1.3
Central Processing Unit (CPU)..................................................................... 1-4
1.4
System memory............................................................................................. 1-7
1.5
Expansion slots........................................................................................... 1-10
1.6Headers........................................................................................................ 1-12
1.7Connectors................................................................................................... 1-13
1.8
Software support......................................................................................... 1-23
Chapter 2:
BIOS information
2.1
Managing and updating your BIOS.............................................................. 2-1
2.2
BIOS setup program...................................................................................... 2-5
2.3
My Favorites................................................................................................... 2-9
2.4
Main menu.................................................................................................... 2-10
2.5
Ai Tweaker menu......................................................................................... 2-11
2.6
Advanced menu........................................................................................... 2-12
2.7
Monitor menu............................................................................................... 2-12
2.8
Boot menu.................................................................................................... 2-13
2.9
Tools menu.................................................................................................. 2-14
2.10 Exit menu..................................................................................................... 2-14
Appendices
Notices........................................................................................................................ 15
ASUS contact information......................................................................................... 17
3
Safety information
Electrical safety
•
To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
•
Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
•
Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
•
Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your retailer.
Operation safety
•
Before installing the motherboard and adding components, carefully read all the user
guides that came with the package.
•
Before using the product, ensure all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
•
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may be exposed to moisture.
•
Place the product on a stable surface.
•
If you encounter technical problems with the product, contact a qualified service
technician or your retailer.
About this guide
This user guide contains the information you need when installing and configuring the
motherboard.
How this guide is organized
This guide contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it
supports. It includes descriptions of the switches, jumpers, and connectors on the
motherboard.
•
Chapter 2: BIOS information
This chapter discusses changing system settings through the BIOS Setup menus.
Detailed descriptions for the BIOS parameters are also provided.
4
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1.
ASUS websites
The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.
2.
Optional documentation
Your product package may include optional documentation, such as warranty flyers,
that may have been added by your dealer. These documents are not part of the
standard package.
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this guide.
DANGER/WARNING: Information to prevent injury to yourself when
completing a task.
CAUTION: Information to prevent damage to the components when
completing a task
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text
Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key>
Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1> + <Key2> + <Key3>
If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
5
Package contents
Check your motherboard package for the following items.
Motherboard
ASUS H81M-V3 motherboard
Cables
2 x Serial ATA 6.0 Gb/s cables
Accessories
1 x I/O Shield
Application DVD
Support DVD
Documentation
User Guide
If any of the above items is damaged or missing, contact your retailer.
H81M-V3 specifications summary
CPU
LGA1150 socket for 4th Generation and New 4th Generation Intel® CoreTM
i7/i5/i3, Pentium®, and Celeron® Processors
Supports Intel® 22nm CPU
Supports Intel® Turbo Boost Technology 2.0*
* The Intel® Turbo Boost Technology 2.0 support depends on the CPU types.
** Refer to www.asus.com for Intel® CPU support list.
Chipset
Intel® H81 Express Chipset
Memory
2 x DIMM, max. 16GB, DDR3 1600 / 1333 / 1066 MHz, non-ECC, unbuffered memory*
Dual-channel memory architecture
Supports Intel® Extreme Memory Profile (XMP)
• Hyper DIMM support is subject to the physical characteristics of individual
CPUs. Please refer to the Memory QVL for details.
• Due to Intel® chipset limitation, DDR3 1600 MHz and higher memory modules on
XMP mode will run at the maximum transfer rate of DDR3 1600 MHz.
• Refer to www.asus.com for the latest Memory QVL (Qualified Vendors List).
• W
hen you install a total memory of 4GB capacity or more, Windows® 32-bit
operating system may only recognize less than 3GB. We recommend a
maximum of 3GB system memory if you are using a Windows® 32-bit operating
system.
Graphics
Integrated Graphics Processor
- Intel® HD Graphics support
Multi-VGA output support: D-SUB, HDMI ports
- Supports D-SUB with max.resolution of 1920 x 1200 @60Hz
- Supports HDMI with max. resolution of 4096 x 2160 @24Hz / 2560 x
1600 @60Hz
Supports Intel® Tru™ 3D/Quick Sync Video/Clear Video HD Technology/
Insider™
Maximum shared memory of 1024 MB
Expansion slots
1 x PCI Express 2.0 x16 slot (@ x16 mode)
1 x PCI Express 2.0 x1 slot
2 x PCI slots
(continued on the next page)
6
H81M-V3 specifications summary
Storage
Intel® H81 Express Chipset:
- 2 x Serial ATA 6.0 Gb/s connectors (gray)
- 2 x Serial ATA 3.0 Gb/s connectors (black)
- Supports Intel® Rapid Technology* and Intel® Smart Connect
Technology**
* Due to the limitation of Intel® H81 chipset, Intel Rapid® Start Technology can be
configured only from the BIOS Setup program.
**The functions will work depending on the CPU installed.
Audio
Realtek® ALC887 7.1-channel Audio CODEC
- Supports jack-detection, multi-streaming, front panel jack-retasking
• Use a chassis with HD audio module in the front panel to support a 7.1-channel
audio output.
LAN
Realtek 8111G PCIe Gigabit LAN controller
USB
Intel® H81 Express Chipset
- ASUS USB 3.0 Boost support
- 2 x USB 3.0/2.0 ports at back panel
- 8 x USB2.0/1.1 ports (6 ports at midboard, 2 ports at back panel)
ASUS unique
features
ASUS 5X Protection
- ASUS motherboards safeguard your PC with 5X Protection: DIGI+VRM,
DRAM Fuse, ESD Guards, High-Quality 5K-Hour Solid Capacitors, and
Stainless Steel Back
ASUS Digital Power Design
- Digital Power Control: Digital Power Design for the CPU
- ASUS 4 Phase Power Design
- ASUS CPU power utility
ASUS DRAM Fuse
- Enhanced DRAM overcurrent protection and short circuit damage
prevention
ASUS ESD Guards
- Strong ESD protection for extended component lifespan
ASUS High-Quality 5K-Hour Solid Capacitors
- 2.5x Longer lifespan with excellent durability
ASUS Stainless Steel Back I/O
- 3x More durable corrosion-resistant coating
ASUS Exclusive Features
- ASUS EPU
- ASUS USB 3.0 Boost
- ASUS Disk Unlocker featuring 3TB+HDD support
- ASUS Ai Charger
- ASUS GPU Boost
- ASUS AI Suite 3
- ASUS Anti-Surge protection
(continued on the next page)
7
H81M-V3 specifications summary
ASUS unique
features
ASUS Quiet Thermal Solution
- ASUS Fanless Design: Stylish Heatsink solution
-ASUS Fan Xpert
ASUS Q-Design
-ASUS Q-Slot
- ASUS EZ DIY
- ASUS CrashFree BIOS 3
- ASUS EZ Flash 2
Rear panel I/O
ports
1 x PS/2 keyboard port (purple)
1 x PS/2 mouse port (green)
2 x USB 3.0/2.0 ports
2 x USB 2.0/1.1 ports
1 x RGB port
1 x HDMI port
1 x LPT port
1 x COM Port
1 x LAN (RJ-45) port
3 x Audio jacks support 8-channel audio output
3 x USB 2.0/1.1 connectors support additional 6 USB 2.0/1.1 ports
Internal
connectors
2 x SATA 6.0 Gb/s connectors
2 x SATA 3.0 Gb/s connectors
1 x 4-pin CPU fan connector (PWM mode)
1 x 4-pin Chassis fan connector (PWM and DC mode)
1 x Front panel audio connector (AAFP)
1 x 24-pin ATX power connector
1 x 4-pin ATX 12V power connector
1 x S/PDIF out connector
1 x COM connector
1 x TPM Header
1 x Speaker connector
1 x Clear CMOS connector
1 x System panel connector
BIOS features
64 Mb Flash ROM, UEFI BIOS, PnP, DMI v2.0, WfM2.0, SM BIOS v2.7,
ACPI v2.0a, SLP3.0, EUP-ready
Manageability
WfM 2.0, DMI 2.0, WOL by PME, PXE
Support DVD
Drivers
ASUS utilities
EZ Update
Anti-virus software (OEM version)
Operating System
Support
Windows® 8.1
Windows® 8
Windows® 7
Form factor
uATX form factor: 9.6”x 7.8” (24.4cm x 19.8cm)
Specifications are subject to change without notice.
8
Product introduction
1.1
Before you proceed
1
Take note of the following precautions before you install motherboard components or change
any motherboard settings.
•
Unplug the power cord from the wall socket before touching any component.
•
Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due
to static electricity.
•
Hold components by the edges to avoid touching the ICs on them.
•
Whenever you uninstall any component, place it on a grounded antistatic pad or in the
bag that came with the component.
•
Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so
may cause severe damage to the motherboard, peripherals, or components.
ASUS H81M-V3
1-1
1.2
Motherboard overview
Before you install the motherboard, study the configuration of your chassis to ensure that the
motherboard fits.
Unplug the power cord before installing or removing the motherboard. Failure to do so can
cause you physical injury and damage to motherboard components.
1.2.1
Placement direction
When installing the motherboard, place it into the chassis in the correct orientation. The edge
with external ports goes to the rear part of the chassis as indicated in the image.
1.2.2
Screw holes
Place six screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
Place this side
towards the rear
of the chassis
H81M-V3
1-2
Chapter 1: Product introduction
1.2.3
Motherboard layout
1
2
3
4
3
5
19.8cm(7.8in)
KBMS
CPU_FAN
DIGI
+VRM
EATXPWR
CHA_FAN
SATA6G_2
LAN_USB34
BATTERY
COM
AUDIO
24.4cm(9.6in)
ASM
1442K
2
SATA6G_1
HDMI
USB3_12
LGA1150
DDR3 DIMM_B1 (64bit, 240-pin module)
VGA
LPT
DDR3 DIMM_A1 (64bit, 240-pin module)
COM
ATX12V
6
PCIEX16
H81M-V3
RTL
8111G
ASM
1083
PCIEX1_1
Super
I/O
Intel®
H81
PCI1
ALC
887-VD2
PCI2
SPDIF_OUT
TPM
CLRTC
AAFP
15
8Mb
BIOS
USB56
USB910
USB1112
14
13
12 11
SATA3G_1
SPEAKER
SATA3G_2
F_PANEL
CHASSIS
10
9
8
7
Connectors/Jumpers/Slots/LED
1.
Serial port connector (10-1 pin COM2)
1-19
2.
ATX power connectors (24-pin ATXPWR, 4-pin ATX12V)
1-15
3.
CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN)
1-18
4.
Intel® LGA1150 CPU socket
1-4
5.
DDR3 DIMM slots
1-7
6.
Intel® H81 Serial ATA 6.0Gb/s connector (7-pin SATA6G_1~2)
1-17
7.
Intel® H81 Serial ATA 3.0Gb/s connector (7-pin SATA3G_1~2)
1-17
8.
System panel connector (10-1 pin F_PANEL)
1-21
9.
Speaker connector (4-pin SPEAKER)
1-19
10.
USB 2.0 connectors (10-1 pin USB56, USB910, USB1112)
1-20
11.
Chassis intrusion connector (4-1 pin CHASSIS)
1-22
12.
Clear RTC RAM (2-pin CLRTC)
1-12
13.
TPM header (20-1 pin TPM)
1-16
14.
Front panel audio connector (10-1 pin AAFP)
1-16
15.
Digital audio connector (4-1 pin SPDIF_OUT)
1-22
ASUS H81M-V3
1-3
1.3
Central Processing Unit (CPU)
This motherboard comes with a surface mount LGA1150 socket designed for the Intel®
4th/5th generation Core™ i7 / Core™ i5 / Core™ i3, Pentium® , and Celeron® processors.
H81M-V3
H81M-V3 CPU socket LGA1150
Unplug all power cables before installing the CPU.
1-4
•
Upon purchase of the motherboard, ensure that the PnP cap is on the socket and
the socket contacts are not bent. Contact your retailer immediately if the PnP cap
is missing, or if you see any damage to the PnP cap/socket contacts/motherboard
components. ASUS will shoulder the cost of repair only if the damage is shipment/
transit-related.
•
Keep the cap after installing the motherboard. ASUS will process Return Merchandise
Authorization (RMA) requests only if the motherboard comes with the cap on the
LGA1150 socket.
•
The product warranty does not cover damage to the socket contacts resulting from
incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP
cap.
Chapter 1: Product introduction
1.3.1
Installing the CPU
1
A
B
3
2
4
5
C
A
B
ASUS H81M-V3
1-5
1.3.2
CPU heatsink and fan assembly installation
Apply the Thermal Interface Material
to the CPU heatsink and CPU
before you install the heatsink and
fan if necessary.
To install the CPU heatsink and fan assembly
A
1
2
B
B
A
3
1-6
4
Chapter 1: Product introduction
To uninstall the CPU heatsink and fan assembly
2
1
A
B
B
A
1.4
System memory
1.4.1Overview
This motherboard comes with two Double Data Rate 3 (DDR3) Dual Inline Memory Modules
(DIMM) sockets.
DIMM_A1
DIMM_B1
A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched
differently to prevent installation on a DDR2 DIMM socket. DDR3 modules are developed for
better performance with less power consumption.
H81M-V3
Channel
Sockets
Channel A
DIMM_A1
Channel B
DIMM_B1
H81M-V3 240-pin DDR3 DIMM sockets
ASUS H81M-V3
1-7
1.4.2
Memory configurations
You may install 1GB, 2GB, 4GB, and 8GB unbuffered non-ECC DDR3 DIMMs into the DIMM
sockets.
1-8
•
You may install varying memory sizes in Channel A and Channel B. The system
maps the total size of the lower-sized channel for the dual-channel configuration. Any
excess memory from the higher-sized channel is then mapped for single-channel
operation.
•
Always install DIMMs with the same CAS latency. For optimal compatibility, we
recommend that you install memory modules of the same version or date code (D/C)
from the same vendor. Check with the retailer to get the correct memory modules.
•
Memory module with memory frequency higher than 2133 MHz and its corresponding
timing or the loaded XMP Profile is not the JEDEC memory standard. The stability and
compatibility of these memory modules depend on the CPU's capabilities and other
installed devices. •
Due to Intel® chipset limitation, DDR3 1600 MHz and higher memory modules on
XMP mode will run at the maximum transfer rate of DDR3 1600 MHz.
•
Due to the memory address limitation on 32-bit Windows® OS, when you install 4GB
or more memory on the motherboard, the actual usable memory for the OS can be
about 3GB or less. For effective use of memory, we recommend that you do any of the
following:
- Use a maximum of 3GB system memory if you are using a 32-bit Windows® OS.
- Install a 64-bit Windows® OS when you want to install 4GB or more on the
motherboard.
•
This motherboard does not support DIMMs made up of 512Mb (64MB) chips or less.
•
The default memory operation frequency is dependent on its Serial Presence Detect
(SPD), which is the standard way of accessing information from a memory module.
Under the default state, some memory modules for overclocking may operate at a
lower frequency than the vendor-marked value. To operate at the vendor-marked
or at a higher frequency, refer to section 2.4 Ai Tweaker menu for manual memory
frequency adjustment.
•
For system stability, use a more efficient memory cooling system to support a full
memory load (2 DIMMs) or overclocking condition.
Chapter 1: Product introduction
1.4.3
Installing a DIMM
To install a DIMM
1
2
3
To remove a DIMM
ASUS H81M-V3
1-9
1.5
Expansion slots
In the future, you may need to install expansion cards. The following sub‑sections describe
the slots and the expansion cards that they support.
Unplug the power cord before adding or removing expansion cards. Failure to do so may
cause you physical injury and damage motherboard components.
1.5.1
Installing an expansion card
To install an expansion card:
1.
Before installing the expansion card, read the documentation that came with it and
make the necessary hardware settings for the card.
2.
Remove the system unit cover (if your motherboard is already installed in a chassis).
3.
Remove the bracket opposite the slot that you intend to use. Keep the screw for later
use.
4.
Align the card connector with the slot and press firmly until the card is completely
seated on the slot.
5.
Secure the card to the chassis with the screw you removed earlier.
6.
Replace the system cover.
1.5.2
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.
Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for
information on BIOS setup.
2.
Assign an IRQ to the card.
3.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that
the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI
groups, making the system unstable and the card inoperable.
1.6.3
PCI Express 2.0 x1 slots
This motherboard supports PCI Express 2.0 x1 network cards, SCSI cards, and other cards
that comply with the PCI Express specifications.
1.6.4
PCI Express 2.0 x16 slot
This motherboard has a 2.0 x16 slot that supports PCI Express 2.0 x16 graphic cards
complying with the PCI Express specifications.
1-10
Chapter 1: Product introduction
IRQ assignments for this motherboard
A
B
C
D
E
F
G
H
PCIEx16
shared
–
–
–
–
–
–
–
PCIEx1_1
–
shared
–
–
–
–
–
–
Realtek 8111G controller
–
–
shared
–
–
–
–
–
PCI 1
–
shared
–
–
–
–
–
–
PCI 2
–
–
shared
–
–
–
–
–
USB2.0 controller 1
–
–
–
–
–
–
–
shared
USB2.0 controller 2
–
–
–
–
shared
–
–
–
HD audio
–
–
–
–
–
–
shared
–
SATA controller 1
–
–
–
shared
–
–
–
–
SATA controller 2
–
–
–
shared
–
–
–
–
ASUS H81M-V3
1-11
1.6Headers
Clear RTC RAM (2-pin CLRTC)
This header allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can
clear the CMOS memory of date, time, and system setup parameters by erasing the
CMOS RTC RAM data. The onboard button cell battery powers the RAM data in
CMOS, which include system setup information such as system passwords.
CLRTC
H81M-V3
1
2
Normal
(Default)
1 2
Clear CMOS
Values (Short)
H81M-V3 Clear RTC RAM
To erase the RTC RAM:
1-12
1.
Turn OFF the computer and unplug the power cord.
2.
Use a metal object such as a screwdriver to short the two pins.
3.
Plug the power cord and turn ON the computer.
4.
Hold down the <Del> key during the boot process and enter BIOS setup to reenter data.
•
If the steps above do not help, remove the onboard battery and short the two pins
again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the
battery.
•
You do not need to clear the RTC when the system hangs due to overclocking. For
system failure due to overclocking, use the CPU Parameter Recall (C.P.R.) feature.
Shut down and reboot the system, then the BIOS automatically resets parameter
settings to default values.
Chapter 1: Product introduction
1.7Connectors
1.7.1
Rear panel connectors
1
2
11
12
3
10
9
4
5 6
8
7
1.
PS/2 mouse port (green). This port is for a PS/2 mouse.
2.
Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices.
3.
USB 3.0 ports. These 9-pin Universal Serial Bus (USB) ports are for USB 3.0 devices.
•
DO NOT connect a keyboard / mouse to any USB 3.0 port when installing Windows®
operating system.
•
Due to USB 3.0 controller limitations, USB 3.0 devices can only be used under a
Windows® OS environment and after USB 3.0 driver installation.
•
USB 3.0 devices can only be used for data storage.
•
We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster
and better performance from your USB 3.0 devices.
4.
LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN)
through a network hub.
LAN port LED indications
Activity Link
LED
Activity/Link LED
Status
Off
Orange
Orange (Blinking)
Orange (Blinking
then steady)
ASUS H81M-V3
Description
No link
Linked
Data activity
Ready to wake up
from S5 mode
Speed LED
Status
Description
OFF
10Mbps connection
ORANGE 100Mbps connection
GREEN
1Gbps connection
Speed
LED
LAN port
1-13
5.
Line In port (light blue). This port connects to the tape, CD, DVD player, or other
audio sources.
6.
Line Out port (lime). This port connects to a headphone or a speaker. In the 4.1, 5.1
and 7.1-channel configurations, the function of this port becomes Front Speaker Out.
7.
Microphone port (pink). This port connects to a microphone.
Refer to the audio configuration table for the function of the audio ports in 2.1, 4.1, 5.1, or
7.1-channel configuration.
Audio 2.1, 4.1, 5.1, or 7.1-channel configuration
Port
Light Blue (Rear
panel)
Lime (Rear panel)
Pink (Rear panel)
Lime (Front panel)
Headset
2.1-channel
4.1-channel
5.1-channel
7.1-channel
Line In
Rear Speaker Out
Rear Speaker Out
Rear Speaker Out
Line Out
Mic In
-
Front Speaker Out
Mic In
-
Front Speaker Out
Bass/Center
-
Front Speaker Out
Bass/Center
Side Speaker Out
To configure a 7.1-channel audio output:
•
Use a chassis with HD audio module in the front panel to support a 7.1-channel audio
output.
8.
USB 2.0 ports. These 9-pin Universal Serial Bus (USB) ports are for USB 2.0/1.1
devices.
9.
HDMI port. This port is for a High-Definition Multimedia Interface (HDMI) connector,
and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other protected
content.
10. Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other
VGA-compatible devices.
11. Serial (COM) port. This 9-pin communication port is for pointing devices or other serial
devices.
12. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
1-14
Chapter 1: Product introduction
1.7.2
1. Internal connectors
ATX power connectors (24-pin EATXPWR, 4-pin ATX12V)
These connectors are for ATX power supply plugs. The power supply plugs are
designed to fit these connectors in only one orientation. Find the proper orientation and
push down firmly until the connectors completely fit.
GND
GND
+12V DC
+12V DC
ATX12V
H81M-V3
EATXPWR
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
PIN 1
GND
+5 Volts
GND
+5 Volts
GND
+3 Volts
+3 Volts
GND
+5 Volts
+5 Volts
+5 Volts
-5 Volts
GND
GND
GND
PSON#
GND
-12 Volts
+3 Volts
PIN 1
H81M-V3 ATX power connectors
•
For a fully configured system, we recommend that you use a power supply unit
(PSU) that complies with ATX 12V Specification 2.0 (or later version) and provides a
minimum power of 350W.
•
DO NOT forget to connect the 4-pin ATX +12V power plug. Otherwise, the system will
not boot up.
•
We recommend that you use a PSU with higher power output when configuring a
system with more power-consuming devices or when you intend to install additional
devices. The system may become unstable or may not boot up if the power is
inadequate.
•
If you are uncertain about the minimum power supply requirement for your system,
refer to the Recommended Power Supply Wattage Calculator at http://support.asus.
com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for details.
ASUS H81M-V3
1-15
2.
TPM connector (20-1 pin TPM)
This connector supports a Trusted Platform Module (TPM) system, which securely
store keys, digital certificates, passwords and data. A TPM system also helps enhance
network security, protect digital identities, and ensures platform integrity.
SB_SUS_STAT
GND
+3VSB
SMBSCL
LAD0
+3V
LAD3
PCIRST#
FRAME
PCICLK
TPM
GND
H81M-V3
RESET
GPIO
SERIRQ
SMBSDA
GND
LAD1
LAD2
PWROWN
PIN 1
H81M-V3 TPM Connector
The TPM module is purchased separately.
3.
Front panel audio connector (10-1 pin AAFP)
NC
AGND
NC
NC
SENSE2_RETUR
AGND
NC
SENSE1_RETUR
This connector is for a chassis-mounted front panel audio I/O module that supports
either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel
audio I/O module cable to this connector.
AAFP
HD-audio-compliant
pin definition
MIC2
MICPWR
Line out_R
NC
Line out_L
H81M-V3
PORT1 L
PORT1 R
PORT2 R
SENSE_SEND
PORT2 L
PIN 1
Legacy AC’97
compliant definition
H81M-V3 Front panel audio connector
1-16
•
We recommend that you connect a high-definition front panel audio module to this
connector to avail of the motherboard’s high-definition audio capability.
•
If you want to connect a high-definition front panel audio module to this connector,
set the Front Panel Type item in the BIOS setup to [HD]. If you want to connect an
AC’97 front panel audio module to this connector, set the item to [AC97]. By default,
this connector is set to [HD]. See section 2.6.7 Onboard Devices Configuration for
details.
Chapter 1: Product introduction
4.Intel® H81 Serial ATA 6.0Gb/s connector (7-pin SATA6G_1~2 [gray])
This connector connects to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0
Gb/s signal cables.
SATA6G_1
GND
RSATA_RXP1
RSATA_RXN1
GND
RSATA_TXN1
RSATA_TXP1
GND
SATA6G_2
H81M-V3
GND
RSATA_RXP2
RSATA_RXN2
GND
RSATA_TXN2
RSATA_TXP2
GND
H81M-V3 SATA 6.0Gb/s connectors
When using hot-plug and NCQ, set the SATA Mode Selection item in the BIOS to [AHCI].
See section 2.6.3 SATA Configuration for details.
5.Intel® H81 Serial ATA 3.0Gb/s connector (7-pin SATA3G_1~2)
This connector connects to Serial ATA 3.0 Gb/s hard disk drives via Serial ATA 3.0
Gb/s signal cables.
SATA3G_2
GND
RSATA_RXP2
RSATA_RXN2
GND
RSATA_TXN2
RSATA_TXP2
GND
GND
RSATA_RXP1
RSATA_RXN1
GND
RSATA_TXN1
RSATA_TXP1
GND
SATA3G_1
H81M-V3
H81M-V3 SATA 3.0Gb/s connectors
When using hot-plug and NCQ, set the SATA Mode Selection item in the BIOS to [AHCI].
ASUS H81M-V3
1-17
6. CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN)
Connect the fan cables to the fan connectors on the motherboard, ensuring that the
black wire of each cable matches the ground pin of the connector.
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
CPU_FAN
CHA_FAN (PWM mode)
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
H81M-V3
+5V
CHA FAN IN
CHA FAN PWR
GND
CHA_FAN(DC mode)
H81M-V3 Fan connectors
1-18
•
Do not forget to connect the fan cables to the fan connectors. Insufficient air flow
inside the system may damage the motherboard components. These are not jumpers!
Do not place jumper caps on the fan connectors!
•
Ensure that the CPU fan cable is securely installed on the CPU fan connector.
•
The CPU_FAN connector supports the CPU fan of maximum 1A (12 W) fan power.
•
Both 3-pin and 4-pin chassis fans support the ASUS Fan Xpert feature.
•
The chassis fan connector supports DC and PWM modes. To set the chassis fan to
DC or PWM, go to Advanced Mode > Monitor > Chassis Fan Q-Fan Control item in
BIOS.
Chapter 1: Product introduction
7.
Serial port connector (10-1 pin COM2)
This connector is for a serial (COM) port. Connect the serial port module cable to this
connector, then install the module to a slot opening at the back of the system chassis.
PIN 1
DCD
TXD
GND
RTS
RI
RXD
DTR
DSR
CTS
COM2
H81M-V3
H81M-V3 Serial port (COM2) connector
The COM module is purchased separately.
8.
Speaker connector (4-pin SPEAKER)
The 4-pin connector is for the chassis-mounted system warning speaker. The speaker
allows you hear system beeps and warnings.
+5V
GND
GND
Speaker Out
SPEAKER
H81M-V3
PIN 1
H81M-V3 Speaker Out connector
ASUS H81M-V3
1-19
9.
USB 2.0 connectors (10-1 pin USB56, USB910, USB1112)
These connectors are for USB 2.0 ports. Connect the USB module cable to any of
these connectors, then install the module to a slot opening at the back of the system
chassis. These USB connectors comply with USB 2.0 specifications and supports up to
480Mbps connection speed.
PIN 1
USB+5V
USB_P12USB_P12+
GND
USB+5V
USB_P9USB_P9+
GND
NC
PIN 1
USB+5V
USB_P10USB_P10+
GND
USB+5V
USB_P6USB_P6+
GND
PIN 1
H81M-V3
USB1112
USB+5V
USB_P11USB_P11+
GND
NC
USB910
USB+5V
USB_P5USB_P5+
GND
NC
USB56
H81M-V3 USB2.0 connectors
Never connect a 1394 cable to the USB connectors. Doing so will damage the
motherboard!
The USB 2.0 module is purchased separately.
1-20
Chapter 1: Product introduction
10. System panel connector (10-1 pin PANEL)
This connector supports several chassis-mounted functions.
F_PANEL
PWR_LED+
PWR_LEDPWR
GND
+PWR LED PWR BTN
HDD_LED+
HDD_LEDGround
HWRST#
(NC)
PIN 1
H81M-V3
+HDD_LED
RESET
H81M-V3 System panel connector
•
System power LED (2-pin PWR_LED)
This 2-pin connector is for the system power LED. Connect the chassis power LED
cable to this connector. The system power LED lights up when you turn on the system
power, and blinks when the system is in sleep mode.
•
Hard disk drive activity LED (2-pin HDD_LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable
to this connector. The HDD LED lights up or flashes when data is read from or written
to the HDD.
•
ATX power button/soft-off button (2-pin PWR_BTN)
This connector is for the system power button.
•
Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without
turning off the system power.
ASUS H81M-V3
1-21
11. Digital audio connector (4-1 pin SPDIF_OUT)
This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port.
SPDIFOUT
GND
H81M-V3
+5V
SPDIF_OUT
H81M-V3 Digital audio connector
The S/PDIF module is purchased separately.
12. Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or switch. Connect
one end of the chassis intrusion sensor or switch cable to this connector. The chassis
intrusion sensor or switch sends a high-level signal to this connector when a chassis
component is removed or replaced. The signal is then generated as a chassis intrusion
event.
By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper
cap. Remove the jumper caps only when you intend to use the chassis intrusion
detection feature.
H81M-V3
Chassis Signal
GND
+5VSB_MB
CHASSIS
PIN 1
H81M-V3 Chassis intrusion connector
1-22
Chapter 1: Product introduction
1.8
Software support
1.8.1
Installing an operating system
This motherboard supports Windows® XP / Windows® Vista / Windows® 7 / Windows® 8
Operating Systems (OS). Always install the latest OS version and corresponding updates to
maximize the features of your hardware.
1.8.2
•
Motherboard settings and hardware options vary. Refer to your OS documentation for
detailed information.
•
Ensure that you install Windows® XP Service Pack 3 or later versions / Windows®
Vista Service Pack 1 or later versions before installing the drivers for better
compatibility and system stability.
Support DVD information
The Support DVD that comes with the motherboard package contains the drivers, software
applications, and utilities that you can install to avail all motherboard features.
The contents of the Support DVD are subject to change at any time without notice. Visit the
ASUS website at www.asus.com for updates.
To run the Support DVD
Place the Support DVD into the optical drive. If Autorun is enabled in your computer, the DVD
automatically displays the Specials screen. Click Drivers, Utilities, AHCI Driver, Manual, and
Contact tabs to display their respective menus.
The following screen is for reference only.
Click an icon to
display Support
DVD/motherboard
information
Click an item to install
If Autorun is NOT enabled on your computer, browse the contents of the Support DVD to
locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run
the DVD.
ASUS H81M-V3
1-23
1-24
Chapter 1: Product introduction
BIOS information
2.1
Managing and updating your BIOS
2
Save a copy of the original motherboard BIOS file to a USB flash disk in case you need to
restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update
utility.
2.1.1
EZ Update
EZ Update is a utility that allows you to automatically update your motherboard’s softwares,
drivers and the BIOS version easily. With this utlity, you can also manually update the saved
BIOS and select a boot logo when the system goes into POST.
To launch EZ Update, click EZ Update on the AI Suite 3 main menu bar.
EZ Update requires an Internet connection either through a network or an ISP (Internet
Service Provider).
2.1.2
ASUS EZ Flash 2
The ASUS EZ Flash 2 feature allows you to update the BIOS without using an OS‑based
utility.
Before you start using this utility, download the latest BIOS file from the ASUS website at
www.asus.com.
To update the BIOS using EZ Flash 2:
1.
Insert the USB flash disk that contains the latest BIOS file to the USB port.
2.
Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select
ASUS EZ Flash 2 Utility and press <Enter> to enable it.
3.
Press <Tab> to switch to the Drive field.
4.
Press the Up/Down arrow keys to find the USB flash disk that contains the latest BIOS,
and then press <Enter>.
ASUS H81M-V3
2-1
5.
Press <Tab> to switch to the Folder Info field.
6.
Press the Up/Down arrow keys to find the BIOS file, and then press <Enter> to perform
the BIOS update process. Reboot the system when the update process is done.
2.1.3
•
This function supports USB flash disks with FAT 32/16 format and single partition only.
•
DO NOT shut down or reset the system while updating the BIOS to prevent system
boot failure!
ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file
when it fails or gets corrupted during the updating process. You can restore a corrupted BIOS
file using the motherboard support DVD or a USB flash drive that contains the updated BIOS
file.
•
Before using this utility, rename the BIOS file in the removable device into
H81MV3.CAP.
•
The BIOS file in the support DVD may not be the latest version. Download the latest
BIOS file from the ASUS website at www.asus.com.
Recovering the BIOS
To recover the BIOS:
1.
Turn on the system.
2.
Insert the support DVD to the optical drive or the USB flash drive that contains the
BIOS file to the USB port.
3.
The utility automatically checks the devices for the BIOS file. When found, the utility
reads the BIOS file and enters ASUS EZ Flash 2 utility automatically.
4.
The system requires you to enter BIOS Setup to recover BIOS setting. To ensure
system compatibility and stability, we recommend that you press <F5> to load default
BIOS values.
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause
system boot failure!
2-2
Chapter 2: Getting started
2.1.4
ASUS BIOS Updater
The ASUS BIOS Updater allows you to update BIOS in DOS environment. This utility also
allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or
gets corrupted during the updating process.
The succeeding utility screens are for reference only. The actual utility screen displays may
not be same as shown.
Before updating BIOS
1.
Prepare the motherboard support DVD and a USB flash drive in FAT32/16 format and
single partition.
2.
Download the latest BIOS file and BIOS Updater from the ASUS website at
http://support.asus.com and save them on the USB flash drive.
NTFS is not supported under DOS environment. Do not save the BIOS file and BIOS
Updater to a hard disk drive or USB flash drive in NTFS format.
3.
Turn off the computer and disconnect all SATA hard disk drives (optional).
Booting the system in DOS environment
1.
Insert the DOS-bootable USB flash drive with the latest BIOS file and BIOS Updater to
your computer’s USB port.
2.
Boot your computer. When the ASUS Logo appears, press <F8> to show the BIOS
Boot Device Select Menu.
ASUS H81M-V3
2-3
3. Select the USB flash drive as the boot device. The DOS screen appears.
Updating the BIOS file
To update the BIOS file using BIOS Updater:
1.
At the FreeDOS prompt, type bupdater /pc /g and press <Enter>.
2.
The BIOS Updater screen appears as below.
ASUSTek BIOS Updater for DOS V1.30
BOARD: H81M-V3
VER: 0316
DATE: 04/11/2014
A:\
H81MV3.CAP
8390656 2014-04-11 17:30:48
3.
Press <Tab> to switch between screen fields and use the <Up/Down/Home/End> keys
to select the BIOS file and press <Enter>. BIOS Updater checks the selected BIOS file
and prompts you to confirm BIOS update.
4.
Select Yes and press <Enter>. When BIOS update is done, press <ESC> to exit BIOS
Updater. Restart your computer.
DO NOT shut down or reset the system while updating the BIOS to prevent system boot
failure!
2-4
Chapter 2: Getting started
2.2
•
For BIOS Updater version 1.30 or later, the utility automatically exits to the DOS
prompt after updating BIOS.
•
Ensure to load the BIOS default settings to ensure system compatibility and stability.
Select the Load Optimized Defaults item under the Exit menu. Refer to section 2.10
Exit menu for details.
•
Ensure to connect all SATA hard disk drives after updating the BIOS file if you have
disconnected them.
BIOS setup program
Use the BIOS Setup program to update the BIOS or configure its parameters. The BIOS
screens include navigation keys and brief online help to guide you in using the BIOS Setup
program.
Entering BIOS Setup at startup
To enter BIOS Setup at startup:
•
Press <Delete> during the Power-On Self Test (POST). If you do not press <Delete>,
POST continues with its routines.
Entering BIOS Setup after POST
To enter BIOS Setup after POST:
•
Press <Ctrl>+<Alt>+<Del> simultaneously.
•
Press the reset button on the system chassis.
•
Press the power button to turn the system off then back on. Do this option only if you
failed to enter BIOS Setup using the first two options.
Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys to force reset from
a running operating system can cause damage to your data or system. We recommend to
always shut down the system properly from the operating system.
ASUS H81M-V3
2-5
•
The BIOS setup screens shown in this section are for reference purposes only, and
may not exactly match what you see on your screen.
•
Visit the ASUS website at www.asus.com to download the latest BIOS file for this
motherboard.
•
Ensure that a USB mouse is connected to your motherboard if you want to use the
mouse to control the BIOS setup program.
•
If the system becomes unstable after changing any BIOS setting, load the default
settings to ensure system compatibility and stability. Select the Load Optimized
Defaults item under the Exit menu or press hotkey F5. See section 2.10 Exit Menu
for details.
•
If the system fails to boot after changing any BIOS setting, try to clear the CMOS and
reset the motherboard to the default value. See section 1.6 Jumpers for information
on how to erase the RTC RAM.
BIOS menu screen
The BIOS setup program can be used under two modes: EZ Mode and Advanced Mode.
You can change modes from the Exit menu or from the Exit/Advanced Mode button in the EZ
Mode/Advanced Mode screen.
EZ Mode
By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ
Mode provides you an overview of the basic system information, and allows you to select
the display language, system performance mode and boot device priority. To access the
Advanced Mode, click Exit/Advanced Mode or press F7 for the advanced BIOS settings.
The default screen for entering the BIOS setup program can be changed.
2-6
Chapter 2: Getting started
Selects the display language of the
BIOS setup program
Displays the CPU temperature, CPU voltage output,
DRAM information and CPU/chassis fan speed
SATA information
Displays the
Advanced mode
menus
Selects the Advanced
Normal mode
mode functions
Power Saving
mode
Exits the BIOS setup program without saving
the changes, saves the changes and resets
the system, or enters the Advanced Mode
Loads optimized default
Displays the system
properties of the
selected mode on the
right hand side
•
The boot device options vary depending on the devices you installed to the system.
•
The Boot Menu(F8) button is available only when the boot device is installed to the
system.
ASUS H81M-V3
2-7
Advanced Mode
The Advanced Mode provides advanced options for experienced end-users to configure the
BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the
following sections for the detailed configurations.
To access the EZ Mode, click Exit, then select ASUS EZ Mode or press F7.
Menu items
Submenu item
Menu bar
Configuration fields
Pop-up window
General help
Navigation keys
Menu bar
Last modified
settings
Quick note
The menu bar on top of the screen has the following main items:
My Favorites For saving the frequently-used system settings and configuration
Main
For changing the basic system configuration
2-8
Ai Tweaker
For changing the overclocking settings
Advanced
For changing the advanced system settings
Monitor
For displaying the system temperature, power status, and changing the
fan settings
Boot
For changing the system boot configuration
Tool
Exit
For configuring options for special functions
For selecting the exit options and loading default settings
Chapter 2: Getting started
2.3
My Favorites
MyFavorites is your personal space where you can easily save and access your favorite
BIOS items.
Adding items to My Favorites
To add frequently-used BIOS items to My Favorites:
1.
Use the arrow keys to select an item that you want to add. When using a mouse, hover
the pointer to the item.
2.
Press <F4> on your keyboard or right-click on your mouse to add the item to My
Favorites page.
You cannot add the following items to My Favorites:
•
Items with submenu options
•
User-configurable items such as language and boot device order
•
Configuration items such as Memory SPD Information, system time and date
ASUS H81M-V3
2-9
2.4
Main menu
The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup
program. The Main menu provides you an overview of the basic system information, and
allows you to set the system date, time, language, and security settings.
2-10
•
If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC)
RAM to clear the BIOS password. See section 1.6 Jumpers for information on how to
erase the RTC RAM.
•
The Administrator or User Password items on top of the screen show the default
Not Installed. After you set a password, these items show Installed.
Chapter 2: Getting started
2.5
Ai Tweaker menu
The Ai Tweaker menu items allow you to configure overclocking-related items.
Be cautious when changing the settings of the Ai Tweaker menu items. Incorrect field
values can cause the system to malfunction.
The configuration options for this section vary depending on the CPU and DIMM model you
installed on the motherboard.
Scroll down to display the other items.
ASUS H81M-V3
2-11
2.6
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system
devices.
Be cautious when changing the settings of the Advanced menu items. Incorrect field values
can cause the system to malfunction.
2.7
Monitor menu
The Monitor menu displays the system temperature/power status, and allows you to change
the fan settings.
2-12
Chapter 2: Getting started
2.8
Boot menu
The Boot menu items allow you to change the system boot options.
Scroll down to display the other items.
ASUS H81M-V3
2-13
2.9
Tools menu
The Tools menu items allow you to configure options for special functions. Select an item
then press <Enter> to display the submenu.
2.10
Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and
save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit
menu.
2-14
Chapter 2: Getting started
Appendices
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
•
This device may not cause harmful interference.
•
This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
IC: Canadian Compliance Statement
Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS
210 of Industry Canada. This Class B device meets all the requirements of the Canadian
interference-causing equipment regulations.
This device complies with Industry Canada license exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Cut appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer
un fonctionnement non souhaité de l’appareil.
ASUS H81M-C R2.0
15
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
This class B digital apparatus complies with Canadian ICES-003.
VCCI: Japan Compliance Statement
VCCI Class B Statement
KC: Korea Warning Statement
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards
for protecting our environment. We believe in providing solutions for you to be able to
responsibly recycle our products, batteries, other components as well as the packaging
materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling
information in different regions.
16
Appendices
ASUS contact information
ASUSTeK COMPUTER INC.
Address
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
Telephone +886-2-2894-3447
Fax +886-2-2890-7798
E-mail
info@asus.com.tw
Web site
http://www.asus.com/tw
Technical Support
Telephone Fax Online support
+86-21-3842-9911
+86-21-5866-8722 ext. 9101#
hhttp://www.asus.com/tw/support
ASUS COMPUTER INTERNATIONAL (America)
Address
800 Corporate Way, Fremont, CA 94539, USA
Telephone+1-510-739-3777
Fax
+1-510-608-4555
Web site
http://www.asus.com/us
Technical Support
Support fax
General support Online support
+1-812-284-0883
+1-812-282-2787
http://www.service.asus.com
ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Web site
Online contact
Harkort Str. 21-23, D-40880 Ratingen, Germany
+49-2102-959931
http://www.asus.com/de
http://eu-rma.asus.com/sales
Technical Support
Telephone+49-2102-5789555
Support Fax
+49-2102-959911
Online support
http://www.asus.com/de/support/
ASUS H81M-C R2.0
17
18
Appendices
(510)739-3777/(510)608-4555
800 Corporate Way, Fremont, CA 94539.
Asus Computer International
Date :
Signature :
Representative Person’s Name :
Dec. 22, 2013
Steve Chang / President
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Supplementary Information:
FCC Part 15, Subpart B, Unintentional Radiators
Model Number : H81M-V3
Conforms to the following specifications:
Product Name : Motherboard
hereby declares that the product
Phone/Fax No:
Address:
Responsible Party Name:
Per FCC Part 2 Section 2. 1077(a)
DECLARATION OF CONFORMITY
Ver. 120601
EC Declaration of Conformity
H81M-V3
Declaration Date: 22/12/2013
Year to begin affixing CE marking:2013
Name :
Signature : __________
CEO
Jerry Shen
Position :
(EC conformity marking)
Regulation (EC) No. 617/2013
CE marking
2011/65/EU-RoHS Directive
Regulation (EC) No. 278/2009
Regulation (EC) No. 642/2009
EN 60065:2002 / A12:2011
EN 301 489-1 V1.9.2(2011-09)
EN 301 489-3 V1.4.1(2002-08)
EN 301 489-4 V1.4.1(2009-05)
EN 301 489-7 V1.3.1(2005-11)
EN 301 489-9 V1.4.1(2007-11)
EN 301 489-17 V2.2.1(2012-09)
EN 301 489-24 V1.5.1(2010-09)
EN 302 326-2 V1.2.2(2007-06)
EN 302 326-3 V1.3.1(2007-09)
EN 301 357-2 V1.4.1(2008-11)
EN 302 291-1 V1.1.1(2005-07)
EN 302 291-2 V1.1.1(2005-07)
EN 55024:2010
EN 61000-3-3:2008
EN 55020:2007+A11:2011
Regulation (EC) No. 1275/2008
2009/125/EC-ErP Directive
EN 60950-1 / A12:2011
2006/95/EC-LVD Directive
EN 300 328 V1.7.1(2006-10)
EN 300 440-1 V1.6.1(2010-08)
EN 300 440-2 V1.4.1(2010-08)
EN 301 511 V9.0.2(2003-03)
EN 301 908-1 V5.2.1(2011-05)
EN 301 908-2 V5.2.1(2011-07)
EN 301 893 V1.6.1(2011-11)
EN 302 544-2 V1.1.1(2009-01)
EN 302 623 V1.1.1(2009-01)
EN 50360:2001
EN 62479:2010
EN 50385:2002
EN 62311:2008
1999/5/EC-R &TTE Directive
EN 55022:2010+AC:2011
EN 61000-3-2:2006+A2:2009
EN 55013:2001+A1:2003+A2:2006
2004/108/EC-EMC Directive
conform with the essential requirements of the following directives:
Model name :
Product name :
Motherboard
GERMANY
declare the following apparatus:
ASUS COMPUTER GmbH
HARKORT STR. 21-23, 40880 RATINGEN
Country:
TAIWAN
Country:
Address, City:
4F, No. 150, LI-TE Rd., PEITOU, TAIPEI 112, TAIWAN
Address, City:
Authorized representative in Europe:
ASUSTeK COMPUTER INC.
Manufacturer:
We, the undersigned,
Ver. 130816