advertisement
Silver Series Operator Interface Terminals
Addendum to Installation and Operation Manual
Operator Interface Terminals
0600-0067-0000 Rev. D
May 2011
1241 Bundy Boulevard, Winona, Minnesota USA 55987
Phone: +1 (507) 454-5300, Fax: +1 (507) 452-4507 http://www.watlow.com
©2011 Watlow. All rights reserved.
TC
Table of Contents
Connecting via Modbus RTU (232/485) ..................................................... 4
Connecting via Modbus TCP (Ethernet) ..................................................... 4
Chapter 3: Communications Basics ............................................................. 5
About Gateways, Controllers and PLCs ..................................................... 5
Parameter Register Addresses .................................................................. 6
Choosing the Communications Drivers ...................................................... 8
Addressing Parameters in Multiple Controllers .......................................... 8
Address Offsets in Multi-Loop Controllers .................................................. 9
Accessing Parameters via EZ-ZONE RUI Gateways and RM Access
Important Things to Know ........................................................................ 10
Chapter 4: Programming Tutorials ............................................................. 11
Create a Popup Window .......................................................................... 14
Create a Meter in a Popup Window ......................................................... 15
Add Increment and Decrement Buttons ................................................... 19
Add an Option List for Control Mode ........................................................ 22
Add a Button to Close the Popup Window ............................................... 24
Compile and Download the Project .......................................................... 28
EZ-ZONE
®
is a registered trademark of Watlow
2
Silver Series OIT Watlow Addendum
1
Chapter 1: Introduction
The Silver Series Operator Interface Terminals (OITs) are powerful human machine interfaces for equipment and processes. EasyBuilder5000 is easy-to-use and flexible software for creating the windows, buttons, displays, gauges and other screen items with which operators interact on the OIT. The purpose of this addendum is to quickly get you up and running with the OIT and software when used with Watlow controllers.
to power and Watlow products.
Chapter 3:Introduction provides definitions and information necessary for using an OIT with Watlow
controllers and other devices. Familiarity with these concepts is assumed in the tutorials that follow.
Chapter 4: Programming Tutorials walks you through the steps of getting Watlow controllers
communicating, creating user interfaces and using powerful user interface features such as trending, data logging and recipes with Watlow controllers.
Additional Resources
In addition to this addendum the following resources are available for learning about Silver Series OITs and EZware-5000 programming software:
Silver Series Installation and Operation Manual—available at Watlow.com in the Download
Center’s User Manuals section; search for “Silver Series”.
Watlow Silver Series OIT Installation Guide—available at Watlow.com in the Download Center’s
User Manuals section; search for “Silver Series”.
EZ-ZONE ALL Modbus register list in Excel—available at Watlow.com in the Download Center’s
User Manuals section; search for “EZ-ZONE ALL”
Silver Series Secrets video tutorial series—available at Watlow.com in the Download Center’s
Training and Education section.
EZware-5000 Software Download for Silver Series OITs—the latest version of software for programming Silver Series OITs from Watlow is always available at Watlow.com in the Download
Center’s Software and Demos section; search for “Silver Series”.
Silver Series Sample Projects—available at Watlow.com in the Download Center’s Software and
Demos section; search for “Silver Series”.
Silver Series Frequently Asked Questions—along with other documents addressing specific topics related to using Silver Series OITs is available at Watlow.com in the Download Center’s Training and
Education section.
3
Silver Series OIT Watlow Addendum
2
Chapter 2: Install and Wiring
Consult the Silver Series Installation and Operation Manual for detailed information on installing and wiring the OITs. This chapter provides important additional information regarding connecting to and communicating with Watlow controllers.
Connecting via Modbus RTU (232/485)
The tables below indicate to which pins on the Silver Series OIT’s DB9 connectors the Watlow EZ-
ZONE
®
screw terminals should connect.
Connecting via 485 2-wire
Silver Series OIT
TS00-0043-0000
TS00-0043-E000
TS00-0070-0000
TS00-0100-0000
Watlow Cable
1
Watlow EZ-ZONE
Function COM1 COM3 COM1 COM3
T-/R- 1 7 1 6
Wire Color Terminals Function
White/Brown CA T-/R-
T+/R+ 2 8 2 9 Brown CB T+/R+
Common 5 5 5 5 Blue CC Common
1
Supports COM1 only. Cable part number: 0219-0374-0000 for TS00-0070-0000 and TS00-0100-0000
or part number 0219-0388-0000 for TS00-0043-0000 and TS00-0043-E0000
Connecting via 232
Silver Series OIT
TS00-0043-0000
TS00-0043-E000
TS00-0070-0000
TS00-0100-0000
Function
TXD
RXD
Common
COM1
6
9
5
Watlow EZ-ZONE
COM1 COM2 COM3 Terminals Function
3 4 7 C2 RD
2
5
6
5
8
5
C3
C5
TX
Common
Connecting via Modbus TCP (Ethernet)
With standard Ethernet cables connect the controller(s) and the Silver Series OIT to an Ethernet switch or connect the controller directly to the OIT.
Determining or Setting the OIT’s IP Address
If you connect the OIT to an Ethernet network in order to download programs or communicate with controllers via Ethernet, you must ensure the OIT has a unique IP address and you will need to know that address in order to communicate from your PC with the OIT.
To read or set the OIT’s IP address:
• Connect a USB mouse to the OIT, if desired and supported.
• Apply power to the OIT.
• Once the OIT is powered up, click the lower right corner of the OIT screen.
• When the button with the arrow or angle bracket appears, click it.
• On the menu bar click the setting button (the one with the wrench or gear icon).
• Enter the password. (By default this is 111111.)
4
Silver Series OIT Watlow Addendum
• The IP address is listed in the System settings window on the Network tab. (If Auto Get IP
Address is selected, the IP Address is not editable. If you want to configure the OIT for a fixed address, select IP address get from below, and enter the IP address here.
• Click OK to close the System settings window on the OIT.
Hints for using the Virtual Keyboard to enter the OIT password and IP addresses:
• If you do not see the Virtual Keyboard it may be minimized; click the X on the menu bar.
• Make sure the cursor is in the Password or IP address field on the System Settings dialog.
• Enter the password by clicking only the keys on the Virtual keyboard. If you click the caption bar or other part of the Virtual keyboard window, your keystrokes are not entered in the System
Settings dialog.
• You can tell the password key strokes are being entered if you hear the key chirp from the OIT and see stars (******) appearing in the password field.
• If you cannot see the Password field, arrange the Virtual Keyboard and System Settings dialog then make sure the cursor is in the Password field.
• If you are entering the password on the Virtual Keyboard but stars aren’t appearing in the
Password field, make sure the Password field has focus. If you do not see the text insertion cursor ( | ) in the Password field, it does not have focus. Click in the Password field to give it focus then click keys, but nothing else on the Virtual Keyboard.
• One you have entered the password and the stars appear in the Password field, you can minimize the Virtual Keyboard by clicking the minimize button at the upper right corner to access the check boxes and buttons on the System Settings dialog.
3
Chapter 3: Communications
Basics
The Silver Series OIT can communicate with Watlow controllers via Modbus TCP or Modbus RTU.
This section defines terms you will encounter and provides information about Modbus communications that will help you create a user interface with the Silver Series OIT for equipment and machines that include Watlow controllers.
About Gateways, Controllers and PLCs
The Silver Series OIT can communicate with a variety of devices. Because many of these devices are
Programmable Logic Controllers (PLCs), EasyBuilder5000 refers to devices in many places generically as “PLCs”. Don’t let this confuse you. When you are setting up the OIT to communicate with a Watlow product, from the OIT’s point of view the controller is a PLC.
This addendum refers to configuring the Silver Series OIT to communicate with “controllers”, but the instructions apply equally to limit controllers and gateways such as the EZ-ZONE
®
RUI Gateway.
5
Silver Series OIT Watlow Addendum
Parameter Register Addresses
The Modbus RTU and Modbus TCP communications protocols assume that each device’s memory is organized in blocks of like-data. Each data block contains either read-only data or read/write data and either bit-size data or word-size (16-bit) data. For example, the Coils data block contains read/write bits and the Input Register data block contains read-only words.
Within each of these data blocks there is a range of memory locations. The data blocks are often referred to by the first digit of their address range. For example, the Holding Registers are often referred to as,
“the 4x registers”. The Modbus standard defines both a numbering scheme and an addressing scheme for the memory locations in the data blocks. The table below illustrates this information for the four most commonly discussed data blocks.
Name
Coils
Discrete Inputs
Input Registers
Holding Registers
Number
0x
1x
Access
Data
Size
Memory Location
Numbers
(Absolute)
Read/Write 1 bit 1 to 65,536
Read-Only 1 bit 100,001 to 165,536
3x
4x
Read-Only Word 300,001 to 365,536
Read/Write Word 400,001 to 465,536
Memory Location
Addresses
(Relative)
0 to 65,535
0 to 65,535
0 to 65,535
0 to 65,535
Because the location numbering scheme includes the data block number, it is helpful to think of it as an
absolute address. The absolute address specifies the address completely or absolutely in that it says which data block and which address contains a piece of data. Because the location addresses do not include the data block number, it is helpful to think of them as relative addresses. They specify where to look relative to the starting point of the data block.
Some software and device manufacturers document the use of their products in terms of the numbering scheme while others use the addresses. In either case the manufacturer typically calls the numbers he supplies, “the addresses.” So to use any two products together you need to know whether or not you have to convert the specified “address” in order to get the result you want.
EasyBuilder5000’s Modbus drivers call the data block, “Device type” and for “Address” expect the memory location’s absolute address without the data block number. For example, to access a value in a holding register with absolute address 401,905, for Device type you select the data block “4x” and enter
“1905” in the Address field. The following illustrates setting this address in EasyBuilder5000.
(072)
Watlow controllers use only the 4x registers. Therefore, you will set the Device type to 4x to access any parameter in a Watlow controller. Watlow manuals specify relative addresses. Therefore, you must add one (1) to an address found in a Watlow manual (other than this manual) before you enter it in
EasyBuilder5000.
Silver Series OIT
6
Watlow Addendum
For example, the EZ-ZONE PM Integrated Controller Models User’s Manual lists the relative address for Heat Power as 1904. To monitor the heat power with the Silver Series OIT, you will add one (1) to the relative address and enter “1905” in the Address field in EasyBuilder5000.
(073)
In summary, when setting an address for a screen object to read or write from a Watlow controller:
• For the Device type select 4x.
• Set the Address to a value that is one greater than the relative Modbus address listed in the
Watlow controller manual.
Address Maps
Some EZ-ZONE products have user-selectable address maps. Select the desired map with the Data Map parameter on the Setup Page’s Communications menu in the controller. The Data Map affects the parameter addresses at which values are read and written. The Data Map setting applies to all the parameters in the controller. Generally Map 2 provides access to more parameters.
For example, the EZ-ZONE PM Integrated Controller Models User’s Manual lists Map1 and Map 2 addresses for Process Value for Analog Inputs 1 and 2. If the Data Map parameter is set to Map 1 then the Process Value for Analog Input 2 is read at address 441 (the listed address plus one), but if Data
Map is set to Map 2 then the Process Value for Analog Input 2 is read at address 451. The address for the Process Value for Analog Input 1 is the same for Map 1 and Map 2.
Silver Series OIT
7
(078)
Watlow Addendum
Choosing the Communications Drivers
When you create a project using EasyBuilder5000 you select the drivers necessary to communicate with the Watlow controllers and any other devices with which the Silver Series OIT must communicate. For
Watlow controllers, you select one of these drivers:
• Modbus RTU Master—used with Watlow controllers that support Modbus RTU and communicate via RS-232 or RS-485.
• Modbus TCP/IP Master—used with Watlow controllers that support Modbus TCP and communicate via Ethernet.
Using the Modbus RTU Master Driver to Communicate via 485
When you set up the Silver Series OIT to communicate via 485, you add a Modbus RTU Master device to the device list in the System Parameter Settings. Only one driver is required for each COM port on the
OIT to which controllers are connected. This is regardless of the number of controllers that are connected to that 485 COM port. Think of the Modbus RTU Master device as a driver for the COM port not as a driver for the controllers themselves. That is why you choose the Modbus RTU Master driver rather than the Modbus RTU Slave driver. The controllers are slaves; the OIT’s COM port is the master.
Using the Modbus RTU Master Driver to Communicate via 232
When you set up the OIT to communicate via a 232 COM port, you add a Modbus RTU Master device to the device list in the System Parameter Settings. When using 232 on a COM port, only one controller can be connected to that port.
Using the Modbus TCP/IP Master Driver to Communicate via Ethernet
When you set up the OIT to communicate with controllers via Ethernet, you add one Modbus TCP/IP
Master device to the device list in the System Parameter Settings dialog for each controller that has an
IP address with which you will communicate. For example, if the OIT must communicate with three EZ-
ZONE controllers via Ethernet, add three Modbus TCP/IP Master devices to the device list in the
System Parameter Settings dialog each configured to communicate with one controller.
Addressing Parameters in Multiple Controllers
Normally the Silver Series OIT assumes that any register address you enter when communicating via
Modbus RTU is associated with the controller at the network address you set in the PLC default station
no field in the Device Properties under the System Parameter Settings.
To read or write data from a register in another controller on a 485 network, enter the network address and register address separated by the number sign or hash mark (#). For example “3#2501” accesses register 2501 in the controller with the Modbus network address 3.
(074)
Silver Series OIT
8
Watlow Addendum
Address Offsets in Multi-Loop Controllers
In controllers with more than one loop of control, more than one limit etc., there is more than one instance of each parameter for these duplicated functions. The manuals for controllers such as the EZ-
ZONE RM, list the Modbus address and an offset for these parameters. Add the offset to the address
once to get the address of the second instance of the parameter, add it twice to get the third instance and so on.
For example, the address of the Heat Power for Loop 1 is listed in the EZ-ZONE RM manual as 2244 with an offset of 70. The following table lists the addresses of the Heat Power parameter for each of the four possible loops in the controller. The table also reminds you to add one (1) to the relative addresses from the controller manuals before entering the parameter address in EasyBuilder5000.
Loop Address + Offset(s)
1 2224
2 2224 + 70
3 2224 + 70 + 70
4 2224 + 70 + 70 + 70
Convert Relative
Address
2224 + 1
2294 + 1
2364 + 1
2434 + 1
Enter in
EasyBuilder5000
2225
2295
2365
2435
Accessing Parameters via EZ-ZONE RUI Gateways and RM
Access Modules
Multiple EZ-ZONE devices can communicate with the Silver Series OIT via one or more EZ-ZONE
RUI Gateways or EZ-ZONE RM Access modules. When ordered with either the Modbus TCP or
Modbus RTU communications option, an RUI Gateway or RM Access module allows a Silver Series
OIT to communicate with multiple EZ-ZONE controllers without purchasing communication options in each controller.
In such a system the Silver Series OIT is connected to and configured to communicate with the gateway.
The gateway presents itself as a single device on the Modbus network; the OIT does not communicate with the controllers, only with the gateway. The gateway is configured by the user with an address offset for each controller connected to it. That address offset is added to the parameter addresses for the controller.
For example, consider three EZ-ZONE PM controllers connected to an RUI Gateway configured with an offset of 0 for the first controller, 5000 for the second controller and 10,000 for the third controller. The table below indicates the addresses that must be entered in EasyBuilder5000 to access the set point value in the three PM controllers.
PM Set Point Plus Gateway Offset
1
2
3
2172
2172
2172
2172 + 0
2172 + 5000
2172 + 10000
Convert Relative
Address
2172 + 1
7172 + 1
12172 + 1
Enter in
EasyBuilder5000
2173
7173
12173
Silver Series OIT
9
Watlow Addendum
Data Types
The Silver Series OIT’s Modbus drivers support a variety of data types. The Watlow manuals specify the data type of each parameter. However the terminology is not precisely the same. The table below correlates the data types indicated in the Watlow documentation with the data types you should select when configuring a screen object in EasyBuilder5000.
EZ-ZONE User’s
Manuals
uint dint float
EZ-ZONE ALL
Modbus List
Enumeration, unsigned 8-bit,
Event, unsigned 16-bit signed 32-bit
IEEE Float
EasyBuilder5000
16-bit Unsigned
32-bit Signed
32-bit Float
Important Things to Know
Note:
Make sure the Modbus Word Order is set to Word Low High in the controller.
That is the setting that works with the Silver Series OIT.
Note:
Examples in this manual use the map 1 addresses. If the controller’s Data Map is set to 2, the examples may not work.
Caution: When you use a multi-state switch object to set an enumerated parameter in a controller, each time the user clicks the switch, the setting selected by the switch is sent to the controller. When it is desirable to go directly from one setting to another without intermediate settings, use a set word object or an option list to set the parameter instead.
Silver Series OIT
10
Watlow Addendum
4
Chapter 4: Programming
Tutorials
The following sections guide you through creating a first project using EasyBuilder5000 and a Silver
Series OIT that communicates with a Watlow controller.
Create a First Project
The following procedure guides you through the process of configuring a Silver Series OIT to communicate with a Watlow Controller.
1) To launch
EasyBuilder5000: on the Windows task bar click
Start, click All
Programs, click
Watlow, click
EZware-5000 and click EasyBuilder
5000.
2) In the Welcome to
EasyBuilder5000 dialog, for Model, choose the OIT model you have.
3) For Display Mode choose Landscape.
4) Make sure Use
template is selected.
5) Click OK.
(001)
Note: If you have previously created a project, that project will open. In that case from the File menu, choose New to create a blank project for this tutorial and to see the Welcome dialog.
Note: The TS00-0070-0000 and TS00-0100-0000 are supported by the same driver.
Note: The TS00-0043-0000 and TS00-0043-E000 are supported by the same driver.
Silver Series OIT
11
Watlow Addendum
6) In the System
Parameter
Settings dialog, in the Device List, select the Local
PLC 1 device and click Settings…
7) For PLC type, choose the appropriate driver.
See the table below.
8) For PLC I/F, choose the appropriate hardware interface.
See the table below.
9) For PLC default
station no. type the controller’s address. Typically this is 1 for the first controller.
10) Click Settings…
(003)
For part numbers like… with…
STxx-xxx-xxxx
PMxxxxx-1xxxxxx
RMCxxxx-xxxx1xx
RMHx-xxxx-x1xx
RMLx-xxxx-x1xx
RMSx-xxxx-x1xx
Modbus RTU
For PLC type choose…
Modbus RTU Master
For PLC I/F choose…
RS-485 2W
(002)
Silver Series OIT
12
Watlow Addendum
For part numbers like… with… For PLC type choose… For PLC I/F choose…
PMxxxxx-2xxxxxx
EZKx-2xxx-xxxx
RMAx-x2xx-xxxx
Modbus RTU Modbus RTU Master RS-232 or RS-485 2W*
PMxxxxx-3xxxxxx
EZKx-3xxx-xxxx
RMAx-x3xx-xxxx
Modbus TCP Modbus TCP/IP Master
Other Watlow Controllers Modbus RTU Modbus RTU Master
Ethernet
RS-232 or RS-485 2W*
*Both 232 and 485 are available; choose the one to which you have connected the OIT.
11) For the Modbus RTU
Master…
• For COM, choose the communications port to which you have connected the controller. Typically this is COM 1.
• For Baud rate, choose the rate that is set in the controller.
(004)
• For Data bits, choose 8 Bits.
• For Parity, choose None.
• For Stop bits, choose 1 Bit.
• For multiple controllers on the same port, for Turn around delay (ms), enter 15 and for Send
ACK delay (ms) enter 15.
• Click OK.
12) For the Modbus
TCP/IP Master…
• For IP address, enter the IP address of the controller.
• Click OK.
13) Click OK to close the
Device Properties dialog.
14) To set up communications with controllers connected to other COM ports or to configure additional controllers communicating via Ethernet:
(005)
• Click New...
• Repeat from step 7 above.
Silver Series OIT
13
Watlow Addendum
15) Click OK to close the System Parameter Settings dialog.
16) Save the project:
• From the File menu, choose Save.
• In File name type First Project.mtp.
• Click Save.
Create a Popup Window
This example assumes you have created a project that configured to communicate with a Watlow controller and that project is open in EasyBuilder5000.
1) From the Window menu, choose Open
Window.
2) Click New…
(006)
3) Click Base Window.
4) Ensure the Name is
Window_011 and the
Window no. is 11.
5) Set Width to 420.
6) Set Height to 300 (272 for the 4.3 in. OIT).
7) To set the background color to white:
• In the Background group, next to Color click .
• Select the white color swatch in the Basic
colors group.
• Click OK.
(007)
8) In the Popup window group, set Start pos. X to 120 (0 for the 4.3 in. OIT).
Silver Series OIT
14
(008)
Watlow Addendum
9) In the Popup window group, set Start pos. Y to 120 (0 for the 4.3 in. OIT).
10) Click OK.
11) In the Open Window dialog, select Window_11.
12) Click Open.
13) From the File menu choose Save.
Create a Meter in a Popup Window
This example assumes you have created a popup window in a project that is configured to communicate with a Watlow Controller and that window is open in EasyBuilder5000.
1) From the Objects menu, choose Meter
Display.
2) Click the General tab.
3) In Description type
Heat Power.
4) Click Settings…
5) For PLC name choose
Modbus RTU Master or Modbus TCP/IP
Master.
6) For Device type choose 4x.
(009)
7) For Address enter the address of the heat power for your controller. See the table.
8) Select the data type in the field below the
Address field. See the table.
9) Click OK.
(075)
For this controller…
RMCxxxx-xxxxxxx
RMHx-xxxx-x1xx
PMxxxxx-xxxxxxx
STxx-xxMx-xxxx
ST via RUI Gateway
Other Controllers
This parameter…
Heat Power
Heat Power
Heat Power
Heat Power
Heat Power
Enter this
Address*…
2245
4125
1905
237
1901
Choose this
Data Type…
32-bit Float
32-bit Float
32-bit Float
32-bit Float
32-bit Float
Consult the controller manual.
*These addresses have already been changed to the absolute form required for EasyBuilder5000 by adding 1 to the value listed in the Watlow manual. Enter them as listed
Silver Series OIT
15
Watlow Addendum
10) Click the Outline tab.
11) In Degree set Start
degree to 270.
12) In Degree set End
degree to 90.
13) In Background uncheck Full circle.
14) In Tick marks check
Enable.
15) For Tick marks
Color, select black.
16) In Tick marks set
Main scale to 6.
17) In Tick marks set Sub
scale to 1.
18) In Tick marks set
Length to 6.
19) Click the Limits tab.
20) Set Value Zero to 0.
21) Set Value Span to
100.
22) Check Range limits
Enable.
23) Set Width to 3.
(010)
(011)
24) Click OK.
25) Move the cursor with the outline of the meter to position it and click to place the meter in
Window_11.
26) Resize the meter with the corner handles to make it smaller, if necessary
Silver Series OIT
16
Watlow Addendum
27) Double-click the meter to open the Meter
Display Object’s
Properties dialog.
28) Click the Profile tab.
29) Set X to 140.
30) Set Y to 60.
31) Set Width to 140.
32) Set Height to 140.
33) Click OK.
34) From the File menu choose Save.
(012)
Add a Numeric Display
This example assumes you have created a window in a project that is configured to communicate with a
Watlow Controller and that window is open in EasyBuilder5000.
1) On the Objects menu, click Numeric/ASCII then choose Numeric
Display.
2) Click the General tab.
3) In Description type
Actual Closed Loop Set
Point.
4) For PLC name choose
Modbus RTU Master or Modbus TCP/IP
Master.
(013)
Silver Series OIT
17
Watlow Addendum
5) For Address choose 4x and enter the address of the Closed Loop
Working/Active Set
Point for your controller. See the table.
6) Click the Numeric
Format tab.
7) In Data format set the data type. See the table.
8) On the Font tab set
Align to Right.
(013)
For this controller…
RMCxxxx-xxxxxxx
RMHx-xxxx-x1xx
PMxxxxx-xxxxxxx
STxx-xxMx-xxxx
ST via RUI Gateway
Other Controllers
This parameter…
Closed Loop
Working/Active
Set Point
(Read Only)
Enter this
Address*…
2513
5233
2173
204
Choose this
Data Type…
32-bit Float
32-bit Float
32-bit Float
32-bit Float
2173 32-bit Float
Consult the controller manual.
*These addresses have already been changed to the absolute form required for EasyBuilder5000 by adding 1 to the value listed in the Watlow manual.
Enter them as listed.
9) Click OK.
10) Move the cursor with the outline to position the display field and click to place it.
11) Adjust the size of the field as needed.
12) From the File menu choose Save.
(014)
Silver Series OIT
18
Watlow Addendum
Add Increment and Decrement Buttons
This example assumes you have created a window in a project that is configured to communicate with a
Watlow Controller and that window is open in EasyBuilder5000.
To add a button that increments the set point:
1) On the Objects menu, click Button then choose Set Word.
2) Click the General tab.
3) In Description type
Increment Set Point.
4) For PLC name choose
Modbus RTU Master or Modbus TCP/IP
Master.
5) Click Setting…
6) For Device type choose 4x.
7) For Address enter the address of the User Set
Point for your controller.
8) Select the data type for the parameter in the field below the
Address field.
(015)
For this controller…
RMCxxxx-xxxxxxx
RMHx-xxxx-x1xx
PMxxxxx-xxxxxxx
STxx-xxMx-xxxx
ST via RUI Gateway
This parameter…
Closed Loop
Set Point
(Read/Write)
Enter this
Address*…
2501
5221
2161
Choose this
Data Type…
32-bit Float
32-bit Float
32-bit Float
22 32-bit Float
2161 32-bit Float
Other Controllers Consult the controller manual.
*These addresses have already been changed to the absolute form required for EasyBuilder5000 by adding 1 to the value listed in the Watlow manual.
Enter them as listed.
9) Click OK.
10) In Attribute for Set
Style choose Press and
hold increment
(JOG++).
11) Set Inc. value to 1.
12) Set Upper Limit to 100 or a value that is safe for your controller’s set point.
13) Set JOG delay to 0.5 seconds.
14) Click the Shape tab.
15) Check Use shape.
Silver Series OIT
19
Watlow Addendum
16) Click Shape
Library…
17) Click Select Lib…
18) Select Arrows 1.plb.
19) Click Open.
20) Locate the button with the triangular arrow pointing up and click it.
21) Click OK to close the
Shape Library.
22) Click OK to close the
New Set Word Object
dialog.
23) Click to place the button.
24) Use the handles to adjust the size of the button.
25) Drag the button to place it as desired on the screen.
26) From the File menu choose Save.
(016)
(017)
Silver Series OIT
20
Watlow Addendum
To add a button that decrements the set point:
1) Click the increment button to select it.
2) From the Edit menu, choose Copy.
3) From the Edit menu, choose Paste.
4) Drag the new button to an appropriate position.
5) Deselect the button by clicking on the window’s background or another item in the window.
(018)
6) Double click the new button to edit its properties.
7) On the General tab change:
• Description to Decrement Set Point
• Set Style to Press and hold decrement (JOG--).
8) Set Bottom Limit to 0.
9) On the Shape tab click Shape Library…
10) Locate the button with the triangular arrow pointing down and click it.
11) Click OK to close the Shape Library.
12) Click OK to close the Set Word Object Properties dialog.
13) From the File menu choose Save.
Silver Series OIT
21
Watlow Addendum
Add an Option List for Control Mode
This example assumes you have created a window in a project that communicates with a Watlow
Controller and that window is open in EasyBuilder5000.
1) On the Objects menu, click Button then choose Option List.
2) Click the General tab.
3) In Description type
Control Mode.
4) Set Mode to Drop-
down list.
5) Set No. of states to 3.
6) In the Control address group:
(019)
• For PLC name choose
Modbus RTU Master or
Modbus TCP/IP Master.
• Click Setting…
• For Device type choose
4x.
• In Address enter the address of the Control
Mode. See the table.
• Select the data type in the field below the
Address field.
• Click OK to close the
Address dialog
For this controller…
RMCxxxx-xxxxxxx
RMHx-xxxx-x1xx
PMxxxxx-xxxxxxx
STxx-xxMx-xxxx
ST via RUI Gateway
Other Controllers
This parameter…
Control Mode
Enter this
Address*…
2221
4101
Choose this
Data Type…
16-bit Unsigned
16-bit Unsigned
1881 16-bit Unsigned
222 16-bit Unsigned
1881
Consult the controller manual.
16-bit Unsigned
*These addresses have already been changed to the absolute form required for EasyBuilder5000 by adding 1 to the value listed in the Watlow manual.
Enter them as listed.
7) Click the Mapping tab.
Silver Series OIT
22
Watlow Addendum
8) In the Values column type the numeric and text values that corresponds to each option you want to include. See the table.
9) Click OK to close the
New Option List
Object dialog.
10) Position the cursor near the bottom center of the window layout and click to place the multi-state switch.
(You may have to move the other objects around to fit everything.)
11) From the File menu choose Save.
State
0
1
2
3 (error)
Value Enumerated Value
10 Auto
54
62
Manual
Off
(022)
(020)
Silver Series OIT
23
Watlow Addendum
Add a Button to Close the Popup Window
This example assumes you have created a window in a project that communicates with a Watlow
Controller and that window is open in EasyBuilder5000.
1) On the Objects menu, click Button then choose Function Key.
2) On the General tab, in
Description type Close
Window.
3) Select Close window.
4) On the Shape tab, uncheck Use shape.
(023)
5) Check Use picture.
6) Click Picture
Library…
7) Click Select Lib…
8) Select Computer.flb.
9) Click Open.
10) Locate the circular grey button with the white x and click to select it.
11) Click OK to close the
Picture Library.
12) On the Label tab, make sure Use label is not checked.
(024)
13) Click OK to close the New Function Key Object dialog.
14) Click to place the function key in the upper right.
15) Double-click the function key to open the Function Key Object’s Properties dialog.
Silver Series OIT
24
Watlow Addendum
16) Click the Profile tab
17) Set Position X to 375.
18) Set Position Y to 5.
19) Set Size Width to 40.
20) Set Size Height to 40.
21) Click OK.
22) From the File menu choose Save.
(025)
Edit the Startup Window
This example assumes you have created a popup window open in EasyBuilder5000 in a project that is configured to communicate with a Watlow Controller.
To add text to the start up window:
1) From the Window menu, choose 1 10 –
Initial.
2) From the Draw menu choose Text.
3) Set these text
Attributes:
• Choose a Font.
• Set Color to white.
• Set Size to 14.
• Set Align to Left.
4) Edit Content to read,
This is the Startup
Screen.
5) Click OK.
(026)
Silver Series OIT
25
Watlow Addendum
6) Position the cursor centered in the top third of the window layout and click to place the text.
7) From the File menu choose Save.
Add a Numeric Display to the main window:
1) On the Objects menu, click Numeric/ASCII and choose Numeric
Display.
2) Click the General tab.
3) In Description type
Process Variable.
4) For PLC name choose
Modbus RTU Master or Modbus TCP/IP
Master.
5) For Address choose
4x.and enter the address of the Analog
Input 1 Process Value.
See the table.
(027)
For this controller…
RMCxxxx-xxxxxxx
RMHx-xxxx-x1xxx
PMxxxxx-xxxxxxx
STxx-xxMx-xxxx
ST via RUI Gateway
Other Controllers
This parameter…
Analog Input 1
Process Value
Enter this
Address*…
Choose this
Data Type…
361 32-bit Float
381 32-bit Float
361 32-bit Float
20 32-bit Float
361
Consult the controller manual.
32-bit Float
*These addresses have already been changed to the absolute form required for EasyBuilder5000 by adding 1 to the value listed in the Watlow manual.
Enter them as listed.
6) Click the Numeric
Format tab.
7) In Data format set the data type.
8) Set Right of decimal
Pt. to 1.
9) On the Font tab set
Align to Right.
10) Click OK.
(028)
(029)
Silver Series OIT
26
Watlow Addendum
11) Move the cursor with the outline to position the display field in the center of the screen and click to place it.
12) From the File menu choose Save.
To create a function key on Window10:
1) On the Objects menu, click Button then choose Function Key.
2) On the General tab, in
Description type Loop
1 Settings.
3) Select Display popup
window.
4) For Style choose No
title bar.
5) For Window no. select
11. Window_011.
6) Click the Shape tab.
7) Check Use shape.
8) Click Shape Library…
(031)
9) In the Library list select Buttons 1.
10) Click one of the buttons to select it.
11) Click OK to close the Shape Library.
12) Click the Label tab.
13) Check Use label.
14) Set Color to black.
15) Set Size to 16.
16) Set Align to Left.
17) In Content type Loop 1.
18) Click OK.
Silver Series OIT
27
(030)
Watlow Addendum
19) Position the cursor and click to place the function key.
20) From the File menu choose Save.
Compile and Download the Project
This example assumes you have a project that is ready to compile and load into an OIT.
To compile the project:
1) From the Tools menu, choose Compile.
2) Click Compile.
3) After the project is compiled, click Close.
(032)
(034)
To download via Ethernet or via a USB cable:
1) If downloading via Ethernet, determine the OIT’s IP address:
• If you don’t already know the OIT’s IP address, follow the instructions in Determining or
Setting the OIT’s IP Address on page 4, note the IP address for use below.
2) If downloading via a USB cable:
• Connect the USB cable to the OIT.
• Apply power to the OIT.
Silver Series OIT
28
Watlow Addendum
• Connect the USB cable to a USB port on the computer.
• If this is the first time you have connected the OIT to the computer via the USB port, locate a follow the procedure in the EasyBuilder 5000 help, “How Do I Install the Maple Systems USB driver?”
3) In EasyBuilder5000 from the Tools menu, choose Download.
4) Select Ethernet or
USB cable.
5) For Ethernet, in HMI
IP select or enter the
OITs IP address.
6) Set Password to the
OITs password
(111111 by default).
7) Check Firmware, if not already checked.
8) Check Reboot HMI
after download, if not already checked.
9) Click Download.
(035)
10) Once the download is complete, click Exit.
Silver Series OIT
29
Watlow Addendum
To download the project via a USB drive to an OIT equipped with a USB Host port:
1) Connect at USB drive to the PC
2) From the Tools menu choose Build Data for
USB Disk or CF Card
Download…
3) Click Browse…
4) Locate and select the
USB drive.
Note: Do not select a sub directory of the USB drive.
Select the root.
5) Click OK to close the
Browse For Folder dialog.
(038)
(039)
6) Click Build.
7) When the files are transferred successfully, click OK.
8) Click Exit to close the USB Disk/CF Card Data dialog.
9) Remove the USB drive from the PC.
To download the from the USB drive to the OIT:
1) Connect a USB mouse to the OIT.
2) Apply power to the OIT.
3) Once the OIT is powered up, connect the USB drive to it.
4) When the download/Upload screen appears on the OIT click Download.
Note: You only have a few seconds to do this before the screen times out. If you miss it, disconnect the
USB drive and connect it again.
Silver Series OIT
30
Watlow Addendum
5) With the Virtual Keyboard enter the Password. (By default this is 111111.)
Note: If you have difficulty entering the password, see the hints below.
6) On the Download Settings dialog make sure Download Project Files is checked.
7) Click OK.
8) In the Pick a Directory dialog expand the usbdisk folder by clicking the plus (+) next to it.
9) Select the folder that represents the USB drive in the usbdisk folder.
Note: The OIT represents the USB drive with a folder icon and a name it assigns such as disk_a_1. You can inspect the contents to be sure you pick the right one. The compiled project is in a directory called mt8000, but be sure to select the USB drive not a sub folder before proceeding.
10) Click OK.
11) Once the project downloads and runs, you can remove the USB drive from the OIT.
Log Data
This example assumes you have a project with at least one controller.
There are two steps to log data with the OIT:
• Copy data from the controller to contiguous local OIT memory with the Data Transfer (Timebased) object—this is necessary only if you want to log more than one parameter in the same file or show multiple parameters together in a Trend Display (graph) or a History Data Display
(table).
• Create a data log with the Data Sampling object.
Note: This example uses specific addresses internal to the OIT. If you have used one or more of these for other purposes you will have to choose appropriate addresses for your project.
Silver Series OIT
31
Watlow Addendum
To copy data to the OIT’s local memory:
1) From the Objects menu choose Data
Transfer (Time-
based).
2) For each item to be logged in the file:
• Click New…
(041)
• In Description type a description of the data to be copied such as
“PV 1”.
• For Address type choose Word.
• For Interval choose a value that is the same as or less than the amount of time you want between data samples.
• In No. of words type word size of the parameter’s data type.
See table.
Data Type
Float
16-bit integer
32-bit integer
No. of words
2
1
2
(042)
• For Source address
PLC name choose
Modbus RTU Master or
Modbus TCP/IP
Master.
• For Source address device type choose 4x.
• In Source address
Address type the address of the parameter to be logged.
For this controller…
RMCxxxx-xxxxxxx
RMHx-xxxx-x1xxx
PMxxxxx-xxxxxxx
STxx-xxMx-xxxx
ST via RUI Gateway
Other Controllers
This parameter…
Analog Input 1
Process Value
Enter this
Address*…
Choose this
Data Type…
361 32-bit Float
381 32-bit Float
361 32-bit Float
20 32-bit Float
361
Consult the controller manual.
32-bit Float
*These addresses have already been changed to the absolute form required for EasyBuilder5000 by adding 1 to the value listed in the Watlow manual.
Enter them as listed.
• For Destination address PLC name choose the OIT (“Local HMI” by default).
• For Destination address device type choose LW.
• In Destination address Address type the local address at which to save the data to be logged.
Silver Series OIT
32
Watlow Addendum
Note: Pick a range of addresses with room to store all the data that must be displayed. For example, use
200 for the first parameter to be logged then for each additional parameter increment the address by the size in words of the previous data. For example, typically you log floats such as process variables and set points which each require two words to store. In that case if the first process variable is copied to 200, set the next parameter to copy to 202 so on. In this example, a process variable, a set point and the heat output power are logged.
• Click OK.
3) Click Exit to close the
Data Transfer (Timebased) Object window.
(043)
To set up data sampling to log the data:
1) From the Objects menu choose Data
Sampling.
2) Click New…
(044)
Silver Series OIT
33
Watlow Addendum
3) In Description type a description for the set of data such as “Loop
1”.
4) For Sampling mode choose Time-based.
5) For Sampling time
interval choose the time between samples.
6) For Read address
PLC name choose the
OIT (“Local HMI” by default).
7) For Read address device type choose
LW.
8) In Read address
Address type the first address to which data was copied. In the example, this is 200.
9) In Max. data records type the number of records to save in a file.
10) Click Data Format…
11) For each item to be logged in the file:
• Click New…
• For Data type choose the data type of the item being logged. Typically
32-bit Float).
• Enter a description for the item to be logged, for example “PV 1”.
• Click OK.
(046)
(045)
(047)
Silver Series OIT
34
Watlow Addendum
12) Click Exit to close the
Data Format window.
(048)
13) Check one or more locations to which to save the data (Save to
USB 1 or Save to
HMI memory).
14) In Folder name type a name for the folder in which the data log file should be created such as “datalog”.
15) Click OK to close the
Data Sampling
Object set up window.
16) Click Exit to close the
Data Sampling
Object window.
(049)
(050)
Create a Graph
This example assumes you have a project with at least one controller and that you have previously configured a time-based data sampling object.
To create and open a window to use for the trend.
1) From the Window menu, choose Open
Window.
2) Click New…
(056)
Silver Series OIT
35
Watlow Addendum
3) Click Base Window.
(007)
4) In Name type Trend.
5) Click OK.
6) In the Window list select Trend.
7) Click Open.
To create buttons to open the Trend window and return to the first window:
1) Select window 10.
2) Select the function key on that screen by clicking it once.
(064)
(065)
3) From the Edit menu, choose Copy.
4) From the Edit menu, choose Paste.
5) Place the copy next to the original.
6) Click on the screen background to deselect the button.
7) Double-click the copy to open the Function Key Object’s Properties window.
8) Edit the Description to read Trend Graph
Window.
9) Choose Change full-
screen window.
10) For Window no. choose 12. Trend.
11) Click the Label tab.
12) Edit the Content to read Trend.
13) Click OK to close the Function Key Object’s Properties window.
14) Select the function key on that screen by clicking it once.
(066)
(057)
Silver Series OIT
36
Watlow Addendum
15) From the Edit menu, choose Copy.
16) Select window 12 Trend.
17) From the Edit menu, choose Paste.
18) Position the button centered at the bottom of the screen.
19) Edit the new button’s properties so that it changes to full-screen window 10 Initial and is labeled “Back”.
To create a trend graph:
1) From the Objects menu choose Trend
Display.
2) In Description type a description of the trend such as “Loop 1 PV,
SP and Heat vs. Time”.
3) For Data Sampling
Object index choose the data sampling object you previously configured.
4) For Trend type choose Real-time.
5) For Distance between data samples/X axis time range choose Time.
(051)
6) In Distance type the number of seconds the width of the trend graph will represent. For example, if you want to see two minutes of data at once, type 120.
7) Click the Trend tab.
8) Choose a Frame color and a Background color.
(052)
Silver Series OIT
37
Watlow Addendum
9) Click the Channel tab.
10) For each channel to be graphed:
• In the Data sampling object group check
Display.
• For Color choose a color that contrasts with the background color.
• In Zero type the value that should be graphed at the bottom of the yaxis.
• In Span type the value that should be graphed at the top of the y-axis.
11) Click OK.
(076)
Note: Keep in mind that while you can choose a different zero and span for each pen, you don’t want to confuse users, so it may be best to graph all the channels against the same zero an span values.
12) Place and size the trend object.
13) Optional: In the Trend
Display Object
Properties dialog
Trend tab enable the
Grid and set it up to display the time.
Silver Series OIT
38
(053)
(054)
Watlow Addendum
14) Optional: Use the
Scale tool to add a scale and labels with the Text tool. Color coordinate these or add a legend if the trend channels don’t all have the same zero and span.
(055)
Use Recipes
This example assumes you have a project with at least one controller in which the recipe memory has not already been used for something else.
In this example we will create a recipe that has five parameters from one controller. For each parameter we will create a data transfer object that saves the parameter’s value in the recipe in the OIT. For these objects the source addresses are the parameters’ Modbus addresses in the controller and the destination addresses are RW (recipe word) addresses in the OIT. See the table.
Note: This example uses specific addresses internal to the OIT. If you have used one or more of these for other purposes you will have to choose appropriate addresses for your project.
To create a recipe window and link it to the other screens:
1) Create and open a window to use for viewing, saving and loading recipes called “Recipe
Manager”.
2) Create a button on window 10 Initial that opens the Recipe Manager window.
3) Create a button on the Recipe Manager window that opens window 10 Initial.
Note: Refer to the Trend example if necessary.
Repeat the following steps to add a data transfer object to the Recipe Manager screen for each parameter you want to save in a recipe. Refer to the table below for addresses etc.:
Parameter
Closed Loop Set Point
Alarm High Set Point
Heat Proportional Band
Integral
Derivative
*ST via RUI Gateway
“Source” Address in Controller
RMC RMH PM ST ST GTW*
2501 5221 2161 22
1741 2661 1481 98
2231 4111 1891 233
2235 4115 1895 227
2237 4117 1897 229
2161
1481
1897
1891
1893
Size in
Words
2
2
2
2
2
“Destination”
Recipe
Address
0
2
4
6
8
Silver Series OIT
39
Watlow Addendum
1) From the Objects menu choose Data
Transfer (Trigger-
based).
2) In Description type
“Recipe Save:” and the name of the name of the parameter
(such as “Loop 1 Set
Point”.
3) For Source address
PLC name choose
Modbus RTU Master or Modbus TCP/IP
Master.
4) For Source address choose 4x and enter the address of the parameter.
5) In No. of words type word size of the parameter’s data type. See Table.
6) Click Setting…
7) For Destination
address PLC name choose the OIT
(Local HMI by default).
Data Type
Float
16-bit integer
32-bit integer
No. of words
2
1
2
(060)
8) For Destination address Device type choose RW to store recipes in the battery backed up recipe word memory.
9) In Destination address Address type 0 for the first item in the recipe (Increment this by the previous item’s No of words for each subsequent recipe item. For example, if the first item was a 16-bit integer, the address of the second item is 1. If the second item is a float, the address of the third item is 3.)
10) If you want to store more than one recipe:
• Check Destination address Index register.
• For Destination address Index choose INDEX 0 (16-bit).
Silver Series OIT
40
Watlow Addendum
11) Click OK to close the Address dialog
12) For Mode choose External Trigger.
13) For Trigger address PLC name choose the OIT (Local HMI by default).
14) For Trigger address Device type choose LB to use an internal bit to cause the OIT to store values in a recipe.
15) In Trigger address Address type 500.
16) Click the Label tab.
17) Check Use label.
18) Set State to 0.
19) In Content type the name of the parameter.
20) Click OK.
21) Place the Data Transfer (Trigger-based) object on the screen.
Repeat the following steps to create the data transfer items that will load recipes in to the controller:
Note: For the data transfer objects that load the recipe from the OIT to the controller, the source addresses are RW (recipe words) addresses in the OIT and the destination addresses are the parameters’
Modbus addresses in the controller.
Parameter
Closed Loop Set Point
Alarm High Set Point
Heat Proportional Band
Integral
Derivative
*ST via RUI Gateway
“Source”
Recipe
Address
0
2
4
6
8
Size in
Words
2
2
2
2
2
“Destination” Address in Controller
RMC RMH PM ST ST GTW*
2501 5221 2161 22 2161
1741 2661 1481 98
2231 4111 1891 233
1481
1897
2235 4115 1895 227
2237 4117 1897 229
1891
1893
Silver Series OIT
41
Watlow Addendum
1) From the Objects menu choose Data
Transfer (Trigger-
based).
2) In Description type
“Recipe Load:” and the name of the parameter (such as
“Loop 1 Set Point”).
3) For Source address
PLC name choose the OIT.
4) For Source address choose RW and type the recipe address for the item.
(062)
5) If you set up the recipe save to use and index register:
• Click Source address Settings…
• Check Source address Index register
• For Source address Index choose INDEX 0 (16-bit).
• Click OK to close the Address dialog.
6) In No. of words type word size of the parameter’s data type.
7) For Destination address PLC name choose Modbus RTU Master or Modbus TCP/IP Master.
8) In Destination address Address choose 4x and enter the controller address of the parameter.
9) For Mode choose External Trigger.
10) For Trigger address PLC name choose the OIT (Local HMI by default).
11) For Trigger address Device type choose LB to use an internal bit to cause the OIT to load recipe values in to a controller.
12) In Trigger address Address type 501.
13) Click the Label tab.
14) Check Use label.
15) Enter the name of the parameter to display.
16) Click OK.
17) Place the Data Transfer (Trigger-based) object on the screen.
Silver Series OIT
42
Watlow Addendum
To create a button to trigger the data transfer objects to copy the values currently in the controller to the corresponding recipe memory in the OIT:
1) On the Objects menu, point to
Button and choose
Set Bit.
2) In Description type
“Save Recipe”.
3) For PLC name choose the OIT
(Local HMI by default).
4) For Address choose
LB and type 500.
(063)
5) For Set style Choose Momentary.
6) Click the Label tab.
7) Check Use label.
8) In Content for state 0 type “Save to OIT”.
9) Click OK.
10) Place the button.
To create a button to trigger the data transfer objects to copy the values currently in the OIT’s recipe memory to the controller:
1) On the Objects menu, point to Button and choose Set Bit.
2) In Description type “Load Recipe”.
3) For PLC name choose the OIT (Local HMI by default).
4) For Address choose LB and type 501.
5) For Set style Choose Momentary.
6) Click the Label tab.
7) Check Use label.
8) In Content for state 0 type “Load from OIT”.
9) Click OK.
10) Place the button.
Note: Using pictures for buttons may help operators.
Silver Series OIT
43
Watlow Addendum
Optional: To see what you are copying from the controller to the OIT’s recipe memory, create an object displaying the current value in the controller next to each Data Transfer (Trigger-based) object. Create a label that indicates what the fields are such as “Current Controller Values”.
Optional: To see or edit directly what is saved in recipe memory create a data entry object for each recipe item. These objects should display the values of the data in the RW memory at the recipe addresses. Create a label that indicates what the fields are such as “Recipe
Values”.
(068)
Optional: The values in the RW addresses are automatically saved in non-volatile memory every five minutes, but adding a button that momentarily sets LB-
9029 forces the values to be saved and can avoid lost data in the event the power is shut off too soon after editing a recipe.
Optional: If you want to store more than one recipe in the OIT, set up the data transfer objects to use indexing for the RW addresses.
(071)
Silver Series OIT
44
Watlow Addendum
Address indexing allows a screen object to display and set the value of different memory locations depending on the value in the index. In this example we use LW-9200 as the address index. Whatever value the index is set to is added to the address in the data transfer (and recipe display) objects. When the index value is zero, the first recipe is used. When the index is 10 the second recipe is used. When the index is 20 the third recipe is used. A multi-state switch is used to set the value of the index when the user selects the recipe.
Controller Memory
2161: (Lp 1 Set Point)
1481: (Lp 1 Hi Alarm)
1891: (Lp 1 Heat PB)
1895: (Lp 1 Integral)
1897: (Lp 1 Derivative)
Recipe Selector
Multi-State Switch
Address = LW 9200
“Recipe 1” = State 0 = 0
“Recipe 2” = State 1 = 10
“Recipe 3” = State 2 = 20
Data Transfer Objects
Data Transfer Object 1
(Lp 1 Set Point)
Address = RW 0 + index
Data Transfer Object 2
(Lp 1 Hi Alarm)
Address = RW 2 + index
Data Transfer Object 3
(Lp 1 Heat PB)
Address = RW 4 + index
Data Transfer Object 4
(Lp 1 Integral)
Address = RW 6 + index
Data Transfer Object 5
(Lp 1 Derivative)
Address = RW 8 + index
LW Memory
LW 9200: address index
RW Memory
Recipe 1 (index = 0)
RW 0: (Lp 1 Set Point)
RW 2: (Lp 1 Hi Alarm)
RW 4: (Lp 1 Heat PB)
RW 6: (Lp 1 Integral)
RW 8: (Lp 1 Derivative)
Recipe 2 (index = 10)
RW 10: (Lp 1 Set Point)
RW 12: (Lp 1 Hi Alarm)
RW 14: (Lp 1 Heat PB)
RW 16: (Lp 1 Integral)
RW 18: (Lp 1 Derivative)
Recipe 3 (index = 20)
RW 20: (Lp 1 Set Point)
RW 22: (Lp 1 Hi Alarm)
RW 24: (Lp 1 Heat PB)
RW 26: (Lp 1 Integral)
RW 28: (Lp 1 Derivative)
Note:
You can also use the address index to create one screen that displays data for one loop at a time with a multi-state switch or option list that allow users to switch from one loop to another.
Silver Series OIT
45
Watlow Addendum
To select the recipe to save to or load from create a multi-state switch to select the recipe as follows:
1) On the Objects menu point to Buttons and choose Multi-State
Switch.
2) In Description type
“Recipe Selector”.
3) Click Read address
Setting…
4) For PLC name choose the OIT
(Local HMI by default).
5) Check System tag.
6) For Device type choose LW-9200
(16bit) : address
index 0.
(069)
7) Click OK to close the Address dialog.
8) Click Write address
Setting…
9) For PLC name choose the OIT
(Local HMI by default).
10) Check System tag.
11) For Device type choose LW-9200 (16bit) : address index 0.
12) Click OK to close the Address dialog.
13) For Switch style choose JOG+.
14) For No. of states choose the number of recipes you want to store.
15) For Cyclical choose Enable.
16) Check User-defined mapping.
Silver Series OIT
46
Watlow Addendum
17) Click Set…
18) For each state enter the appropriate offset
Value. For state 0 enter 0. For state 1 enter a value that will offset the beginning of the second recipe beyond the end of the first in the recipe memory.
19) Click OK to close the State mapping window.
(070)
Note: The first recipe is selected with the multi-state switch in its state
0. This recipe stores its values in the memory locations you entered in the data transfer objects with no offset from address indexing, so for state 0 the Value is 0. Calculate the minimum offset for the second recipe by finding the sum of the number of words in memory used to store the items in one recipe. The second recipe (state 1 for the multistate switch) should set the offset to this sum. The third recipe (state 2) should set the offset to twice the sum. The fourth recipe (state 3) should set the offset to three times the sum. And so on.
20) Click the Label tab.
21) Check Use label.
22) In Content enter a label indicating which recipe is selected. (For state 0 type “Recipe 1”, for state 1 type “Recipe 2” etc.)
23) Click OK and place the Multi-State Switch object on the screen.
To create a button to save the recipes in non-volitile memory:
1) On the Objects menu point to Buttons and choose Set Bit.
2) In Description type “Save Recipes”.
3) Click Write address Setting…
4) For PLC name choose the OIT (Local HMI by default).
5) Check System tag.
6) For Device type choose LB-9029 : save all rcipe data to machine (set ON).
7) Click OK to close the Address dialog.
8) For Set style choose Momentary.
9) Click the Label tab.
10) Check Use label.
11) In Content enter, “Save Recipes”.
12) Click OK and place the Set Bit object on the screen.
Silver Series OIT
47
Watlow Addendum
How to Reach Us
Corporate Headquarters
Watlow Electric Manufacturing Company
12001 Lackland Road
St. Louis, MO 63146
Sales: 1-800-WATLOW2
Manufacturing Support: 1-800-4WATLOW
Email: [email protected]
Website: www.watlow.com
From outside the USA and Canada:
Tel: +1 (314) 878-4600
Fax: +1 (314) 878-6814
Europe
Watlow France
Tour d'Asnières.
4 Avenue Laurent Cély
92600 Asnières sur Seine
France
Tél: + 33 (0)1 41 32 79 70
Télécopie: + 33(0)1 47 33 36 57
Email: [email protected]
Website: www.watlow.fr
Watlow Ibérica, S.L.U.
C/Marte 12, Posterior, Local 9
E-28850 Torrejón de Ardoz
Madrid - Spain
T. +34 91 675 12 92
F. +34 91 648 73 80
Email: [email protected]
Website: www.watlow.es
Latin America
Watlow de México S.A. de C.V.
Av. Fundición No. 5
Col. Parques Industriales
Querétaro, Qro. CP-76130
Mexico
Tel: +52 442 217-6235
Fax: +52 442 217-6403
Watlow GmbH
Postfach 11 65, Lauchwasenstr. 1
D-76709 Kronau
Germany
Tel: +49 (0) 7253 9400-0
Fax: +49 (0) 7253 9400-900
Email: [email protected]
Website: www.watlow.de
Watlow Italy S.r.l.
Viale Italia 52/54
20094 Corsico MI
Italy
Tel: +39 024588841
Fax: +39 0245869954
Email: [email protected]
Website: www.watlow.it
Asia and Pacifi c
Watlow Singapore Pte Ltd.
16 Ayer Rajah Crescent,
#06-03/04,
Singapore 139965
Tel: +65 6773 9488 Fax: +65 6778 0323
Email: [email protected] Website: www.watlow.com.sg
Watlow UK Ltd.
Linby Industrial Estate
Linby, Nottingham, NG15 8AA
United Kingdom
Telephone: (0) 115 964 0777
Fax: (0) 115 964 0071
Email: [email protected]
Website: www.watlow.co.uk
From outside The United Kingdom:
Tel: +44 115 964 0777
Fax: +44 115 964 0071
Watlow Korea Co., Ltd.
#1406, E&C Dream Tower, 46, Yangpyeongdong-3ga
Yeongdeungpo-gu, Seoul 150-103
Republic of Korea
Tel: +82 (2) 2628-5770 Fax: +82 (2) 2628-5771
Website: www.watlow.co.kr
Watlow Australia Pty., Ltd.
4/57 Sharps Road
Tullamarine, VIC 3043
Australia
Tel: +61 3 9335 6449
Fax: +61 3 9330 3566
Website: www.watlow.com
Watlow Electric Manufacturing Company (Shanghai) Co. Ltd.
Room 501, Building 10, KIC Plaza
290 Songhu Road, Yangpu District
Shanghai, China 200433
China
Phone:
Local: 4006 Watlow (4006 928569)
International: +86 21 3381 0188
Fax: +86 21 6106 1423
Email: [email protected]
Website: www.watlow.cn
Watlow Malaysia Sdn Bhd
1F-17, IOI Business Park
No.1, Persiaran Puchong Jaya Selatan
Bandar Puchong Jaya
47100 Puchong, Selangor D.E.
Malaysia
Tel: +60 3 8076 8745 Fax: +60 3 8076 7186
Email: [email protected]
Website: www.watlow.com
瓦特龍電機股份有限公司
80143 高雄市前金區七賢二路189號 10樓之一
電話: 07-2885168 傳真: 07-2885568
Watlow Electric Taiwan Corporation
10F-1 No.189 Chi-Shen 2nd Road Kaohsiung 80143
Taiwan
Tel: +886-7-2885168 Fax: +886-7-2885568
Your Authorized Watlow Distributor
ワトロー・ジャパン株式会社
〒101-0047 東京都千代田区内神田1-14-4
四国ビル別館9階
Tel: 03-3518-6630 Fax: 03-3518-6632
Email: [email protected] Website: www.watlow.co.jp
Watlow Japan Ltd.
1-14-4 Uchikanda, Chiyoda-Ku
Tokyo 101-0047
Japan
Tel: +81-3-3518-6630 Fax: +81-3-3518-6632
Email: [email protected] Website: www.
watlow.co.jp
TOTAL
CU ST ER
S ATIS CTIIO N
3 Year Warranty
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project