advertisement
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
USR-TCP232-300
Hard version: V2.0
File version: V1.1
2011-8-17
Serial Device Server - RS232/RS485 to Ethernet converter is an Equipment for convert TCP or UDP socket data to RS232 or RS485, easy to use, low price, low power, 32 bits arm on board, high speed, high Stability.
Our concept: simple functions, stable performance, reasonable price.
We can supply Custom services, hardware, software and Server, welcome to contact us.
Jinan USR IOT Technology Co., Ltd.
Page 1 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
Jinan USR IOT Technology Co., Ltd.
Page 2 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
Serial Device Server - RS232/RS485 to Ethernet converter is an Equipment for convert TCP or UDP socket data to RS232 or RS485, easy to use, low price, low power, 32 bits arm on board, high speed , high
Stability.
This is a multi-functional embedded Ethernet serial data conversion device that integrates a TCP / IP protocol stack, the user can easily use it to network functionality of embedded devices, upgrade the existing serial devices into a network function, saving human and material resources and development time, make the product faster to market, enhance their competitiveness.
There is 10/100M auto detected RJ45 interface, RS232 bound rate up to 230.4Kbps, can work at TCP
Server, TCP Client, UDP and UDP server mode, setup easily via RS232 or RJ45.
�
100M high speed Ethernet card, 10/100M auto detect interface;
� support AUTO MDI/MDIX, Can use a crossover cable or parallel cable connection;
� RS232 bound rate can set up from 300 to 256000
�
RS485 bound rate can set up from 300 to 115200
� Work mode TCP Server, TCP Client, UDP, UDP Server
�
Virtual serial port supported;
� across the gateway, across switches, routers
� Can work in LAN, also can work on the Internet (external network)
�
Working port, destination IP address and port can be easily set up;
� Automatically connection to ensure a reliable network to establish the TCP connection;
�
Transmission distance: RS232 - 15 meters, RS485 - 1000 meters, cable 200 meters (after the switches together through the Internet, no distance limit)
� 32 bits ARM CPU inside;
�
LAN : 10/100Mbps; protect: Built-2KV isolated electromagnetic;
�
RS232 x 1: TXD RXD GND;
� RS485 x 1: A (Data+) B (Data-); 120 Ohms Termination Resistance on board.
� network protocol: ETHERNET ARP IP UDP TCP ICMP;
� Software tool: configuration software, TCP/UDP test soft, RS232 debug soft.
�
Configuration method: RS232 or via Ethernet, free software available.
�
Power : DC 5V / 500mA
� Size (L×W×H): 90×83×25(mm)
�
Operating temperature: -25~75°C.
� Save the environment: -40~85°C, 5~95%RH.
Jinan USR IOT Technology Co., Ltd.
Page 3 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
Serial device server module for connecting serial industrial automation equipment such as PLC, sensors, meters, motors, drives, bar code readers and displays and design. Serial server module is widely used in attendance, access control systems, Canteen machines, POS systems, building control, fire control, the banking system, engine room monitoring, UPS monitoring, power, oil, environmental monitoring, industrial applications and other areas all need to serial devices Data network management where you can use a serial device server solution.
Name
Ethernet card for
MCU
RS232 to Ethernet convert module
RS232/RS485 to
Ethernet convert module
Ethernet to TTL module
Serial Device Server
Model
USR-TCP232-T
USR-TCP232-2
USR-TCP232-24
USR-TCP232-D
USR-TCP232-300
TTL
RS232
RS485/RS234
TTL interface
RS232/RS485
Explain
For PCB embedded customers use, with RJ45 Block
RS232 to TCP/IP
RS232/RS485 choose via Jumper
DIP module,For PCB embedded customers use,with out RJ45
With shell serial servers, network setting parameters
Model Description: USR is our brand, TCP232 that TCPIP to serial module product, 2/4/T that serial-side level in the form.
Operating voltage: 5V
Operating current: 200mA
Operating Temperature: -25 ~ 75 ° C
Storage Temperature: -40 ~ 85 ° C
Storage Humidity: 5% ~ 95% RH
� 1. Serial Device Server - RS232/RS485 to Ethernet converter * 1
�
2. 110~240V AC to 5V DC power adapter * 1
� 3. Network cable * 1
� 4. RS232 cable (Male to Male: 2-3 3-2 cross) *1
�
5. CD with soft and user guide in English *1
Jinan USR IOT Technology Co., Ltd.
Page 4 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
USR-TCP232-300 is bridge to connect the network to Serial device, with the RS232/RS485 to Ethernet convert module; users can easily manage and control network devices, application diagram below.
R S 2 3 2 /
R S 4 8 5
Ethernet
User system
When work at TCP client mode, the module auto connect to destination IP and port, make a TCP connection for send or receive data. Destination IP can be a WAN IP or Ethernet IP.
1. Module try to connect to server
1.Server listen a TCP port
2. Data transfer through the connection
R S 2 3 2
R S 4 8 5
S y s t e m
R S 2 3 2
Ethernet
Module work at TCP Client mode
Jinan USR IOT Technology Co., Ltd.
Page 5 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
Work at UDP mode, Module listen a UDP port, and pc listen a UDP port, when need to send data, UDP packet will be send.
1. Module listen a UDP port 1.PC listen a UDP port
2. Data transfer With out connection, only data packet
R S 2 3 2
R S 4 8 5
S y s t e m
R S 2 3 2 Ethernet
Module work at UDP mode
Jinan USR IOT Technology Co., Ltd.
Page 6 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
Like the socket UDP server in pc API. Many to one data transfer supported, the data from uart/232/485 part will be transformed to the last UDP packet’s address.
1. Module listen a UDP port
1.PC listen a UDP port
R S 2 3 2
R S 4 8 5
S y s t e m
R S 2 3 2
Module work at UDP Server mode
Ethernet
P C -A
1
2
3
P C -B
Jinan USR IOT Technology Co., Ltd.
Page 7 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
R S 2 3 2
R S 4 8 5
S y s te m
1. module listen TCP port
1. PC connect to the port
2. data transfer from MCU to PC
R S 2 3 2 Ethernet
U S R -T C P 2 3 2 -300 work at TCP Server mode
N e w p c
c o n n e c t e d
Da t a
t ra n s d an f e b a r ck g o
P C -D
P C -A
It can accept 4 links at the same time.
P C -C
P C -B
Jinan USR IOT Technology Co., Ltd.
Page 8 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
There is two lamps in RJ45 connector, one is green, and the other is yellow. And 1 power led.
LED red name
Power green Link state yellow Data transfer description
Light When Power on
Light when 100Mbps network linked
Blink when there is data in or out
RS232 use 9 pin female (hole), only 3 pins in use, others are NC, the detail is below.
5 4 3 2 1
9 8 7 6
ID
2
3
5
Mark
TXD
RXD
GND
Description
RS232 Send of module
RS232 Receive of module
Ground
We can offer two kinds of serial lines, if needed, please choose to buy:
1. Male to Female direct serial cable: connect serial server and the computer directly to debugging and
Testing.
2. Male to Male and Cross Pin2 and Pin3 serial cable: used to connect RS232 serial port server and general user equipment.
RS485 has two lines A (data+) and B (data-), 120 Ohms Termination Resistance on board.
if you need to use RS485, please open the box and change the jumpers.
Jinan USR IOT Technology Co., Ltd.
Page 9 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
Auto detected 10M/100M RJ45 interface, support AUTO MDI/MDIX,that is to say you can use crossover cable or a straight cable to connect it to PC for test.
7
8
5
6
2
3
Pin
1
4
Name
TX+
TX-
RX+ n/c n/c
RXn/c n/c
Description
Transceiver Data+
Transceiver Data-
Receive Data+
Not connected
Not connected
Receive Data-
Not connected
Not connected
U n i t :m m
4
7 6 m m
8 3 m m
Jinan USR IOT Technology Co., Ltd.
Page 10 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
Parameters: work mode, source IP, source port, net mask, gateway, UART baud rate, destination IP, destination port.
Note: This module does not support network settings by default, if you need network settings module ,please tell us before buying, network settings and serial port settings can only choose one.
The steps for setting via RJ45:
1. Connect the module to the LAN with PC or connect to PC, power on the module.
2. Open the setup software, click Search, find modules, and choose the one you want to change settings.
4. (Optional step) after setup, the module will restart in 5 seconds; you can re click Search to check new config.
5. Power down the module and Power on, the module will work at new configuration.
Jinan USR IOT Technology Co., Ltd.
Page 11 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
The default work mode is TCP Client and the setting is same as the picture show on last page.
First, you can ping the module, if you are in the same LAN with the module.
Default work mode test:
1. What you need for test, A PC with a RS232 interface, 5V Power adapter, RS232 cable, Ethernet Cable,
Test software. If your PC has no RS232 interface, you can use a USB to RS232 convert product.
2. Hardware connects: Connect the module to your PC, RS232 to PC’s RS232 and Ethernet RJ45 to
PC’s RJ45 Ethernet, you can use the Cross or Directly Connect net cable, because the module support
AUTO MDI/MDIX.
Powe r o n
Ether net c able
R S23
2 c ab le
3. Setup the PC IP address to 192.168.0.201
Jinan USR IOT Technology Co., Ltd.
Page 12 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
4. Open the test software, choose Correct COM port, open com port, listen TCP port.
1.
After a short while, the module will connect to the software, as you can see 192.168.0.7:20108.
2.
Now you can send from RS232, receive from Ethernet; and send from Ethernet, receive from
RS232.
Jinan USR IOT Technology Co., Ltd.
Page 13 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter
Single-port TCP/IP - serial bridge (RFC 2217) http://en.usr.cn
1. setup the module
2. Install VSPM
3. Open VSPM,
Add virtual COM.
Jinan USR IOT Technology Co., Ltd.
Page 14 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
4. Setup as the follow pictures, you need to notice COM port, bond rate and work mode of PC, then click
5. After Activate click, a Virtual COM port COM2, will be created, COM2 will receive data from TCPIP socket, and send data to COM2 will convert to TCPIP socket data to remote Equipment.
If create failed, please notice to see error notice and log, when use Virtual COM Port, you should close other software who use the same TCPIP port.
The success picture as follow:
Jinan USR IOT Technology Co., Ltd.
Page 15 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
At this point, you can use your equipment as an ordinary serial port, and operate of local virtual serial port will converted to operation of the remote module RS232. The figure is show send data between the two serial port.
Jinan USR IOT Technology Co., Ltd.
Page 16 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter http://en.usr.cn
Test 100ms recycle send, send and receive 10,0000 bytes, every thing is ok.
Jinan USR IOT Technology Co., Ltd.
Page 17 of 18 [email protected]
Serial Device Server - RS232/RS485 to Ethernet converter
Company: Jinan USR IOT Technology Co., Ltd
Address: 1-523, Huizhan Guoji Cheng, Gaoxin Qu, Jinan, Shandong, China
Tel: 86-531-55507297 86-531-88826739
Web: http://en.usr.cn
Email: [email protected]
http://en.usr.cn
Version 1.0 2011-05-26
Version 1.1 2011-06-30 add new test software
Version 1.2 2011-08-17 add TCP Server mode and virtual COM test
Jinan USR IOT Technology Co., Ltd.
Page 18 of 18 [email protected]
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project