Viking VICU2666BSB Installation guide

Viking Installation Guide
®
HOT
Viking Range Corporation
HOT
REAR
REAR
FRONT
FRONT
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
HOT
or visit the Viking Web site at
HOT
HOT
REAR
REAR
REAR
FRONT
FRONT
FRONT
vikingrange.com
Built-In Induction Cooktops
F20529E EN
(033111)
Table of Contents
IMPORTANT– Please Read and Follow
Warnings & Important Safety Instructions _______________________________________________3
Dimensions (30”W.) __________________________________________________________________5
Dimensions (36”W.) __________________________________________________________________5
Specifications _______________________________________________________________________6
Cutout Dimensions __________________________________________________________________7
Clearance Dimensions________________________________________________________________9
Electrical Requirements _____________________________________________________________12
General Information ________________________________________________________________13
Installation _________________________________________________________________________13
Final Preparation ___________________________________________________________________14
Performance Checklist ______________________________________________________________14
Service & Registration_______________________________________________________________15
• Before beginning, please read these
instructions completely and carefully.
• DO NOT remove permanently affixed
labels, warnings, or plates from the
product. This may void the warranty.
Your safety and the safety of others is
very important.
• Please observe all local and national
codes and ordinances. Installation must
conform with local codes and National Fuel
Gas Code ANSIZ233.1/NFPA-54 –latest
edition.
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all
safety messages.
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
• Please ensure that this product is properly
grounded.
All safety messages will be preceded by
the safety alert symbol and the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
• The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future
reference.
DANGER
• Installation must conform with local codes
or, in the absence of codes, the National
Electrical Code, ANSI/NFPA 70-latest
edition.
WARNING
In Canada: Electrical installation must be in
accordance with the current CSA C22.1
Canadian Electrical Codes Part 1 and/or
local codes.
Hazards or unsafe practices
which WILL result in severe personal
injury or death
Hazards or unsafe practices
which COULD result in severe personal
injury or death
CAUTION
Hazards or unsafe practices which
COULD result in minor personal injury
or property damage.
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
2
3
IMPORTANT– Please Read and Follow
WARNING
CAUTION
BURN HAZARD
Dimensions
Electric 30” Induction Cooktop
Be sure the electric power is
off from the breaker box to the
junction box until the cooktop
is installed and ready to
operate. The junction box should be
connected to a suitable ground.
The use of cabinets for
storage above the appliance
may result in potential burn
hazard. Combustible items
may ignite, metallic items may become
hot and cause burns. If a cabinet storage
is to provided the risk can be reduced by
installing a range hood that projects
horizontally a minimum of 5” beyond the
bottom of the cabinets.
(30”W. and (36”W.)
HO
REA
R
T
FRO
NT
WARNING
HO
T
REA
R
FRO
NT
30
The electrical power to the
unit must be shut off while line
connections are being made.
Failure to do so could result
in serious injury or death.
WARNING
ELECTRICAL
GROUNDING
INSTRUCTIONS
FIRE AND ELECTRICAL
SHOCK HAZARD
DO NOT use an extension
cord with this appliance. Such
use may result in fire, electrical
shock, or other personal injury.
”
21 cm)
.4
(53
1-5/8”
30-3/4”
(4.1 cm)
(78.1 cm)
4”
3-1/4”
WARNING
This cooktop must be electrically
grounded in accordance with local codes
or, in the absence of codes, with the
National Electrical Code, ANSI/NFPA 70latest edition. FOR PERSONAL
SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
-
(78 3/4”
.1 c
m)
(10.2 cm)
(9.5 cm)
Electric 36” Induction Cooktop
O
H
AR
RE
T
FR
ON
T
H
O
AR
RE
T
FR
ON
T
H
O
AR
RE
T
FR
ON
T
36
-
(93 3/4”
.3 c
m)
”
21 cm)
.4
(53
1-5/8”
(4.1 cm)
36-3/4”
(93.3 cm)
4
3-1/4”
4”
(9.5 cm)
(10.2 cm)
5
Specifications
Cutout Dimensions
Induction Cooktop
Description
VICU206
VICU266
Overall width
30-3/4” (78.1 cm)
36-3/4” (93.3 cm)
(
5-5/8” (14.3 cm)
4” (10.2 cm)
3-1/4” (8.3 cm)
Overall depth from rear
Maximum amp usage
Surface element rating
Right front
Right rear
Center front
Center rear
Left front
Left rear
Approximate
shipping weight
34-5/8” (87.9 cm) minimum to
35-3/4” (90.8 cm) maximum
19-1/8” (48.6 cm) minimum to 20” (50.8 cm) maximum
240-208/120 VAC; 50/60Hz; factory-installed 4 ft. (121.9 cm) flexible steel
conduit 3-wire conduit with a No. 10 ground wire; located on
the right rear corner of unit
240V—30.8 amps (7.4 kw)
208V—30.8 amps (6.4 kw)
240V—46.3 amps (11.1 kw)
208V—46.3 amps (9.6 kw)
1,850 watts
1,850 watts
N/A
N/A
3,700 watts boost/2,300 watts
1,400 watts
1,400 watts
3,300 watts boost/2,300 watts
1,850 watts
1,850 watts
3,700 watts boost/2,300 watts
1,400 watts
52 lb. (23.6 kg)
63 lb. (28.6 kg)
2 35
.
(6
Electrical requirements
28-5/8” (72.7 cm) minimum to
29-3/4” (75.6 cm) maximum
*
” )
1 cm
4 ”
.5 to 2 )*
(2 -1/ cm
Cutout depth
21” (53.3 cm)
A
Cutout width
”
/8 m)
-1 c
9 6
1 48.
Overall height from bottom
To top of knobs
To top of cooking surface
To bottom edge of frame
30”W. Models
A
36”W. Models
28-5/8” (72.7 cm) min. to 34-5/8” (87.9 cm) min. to
29-3/4” (75.6 cm) max.
35-3/4” (90.8 cm) max.
*Note: Based on a 24” (61 cm) deep cabinet with a 25”
(64 cm) deep countertop and 3/4” (1.9 cm) backsplash.
6
7
Cutout Dimensions
(VICU Cooktop over Single Electric Oven)*
Clearance Dimensions
”
1 4
.5
(2
/2
to
-1 5
2 6.3
cm
to
Interior Cabinet Clearances
”
)
cm
1 48
(
”
/8 )
-3 cm
4
1 6.5
3
” (
/8 )
-3 cm
4
1 6.5
(3
(91”min
.4 .
cm
)
”
/8 )
-7 cm
36
6
2 3.3
(7
/8 ” m )
9-1 .6 c
28
(71-1/8
.4 ”
cm
)
IMPORTANT: The electronic components for the induction elements in the cooktop need air circulation. To
ensure long life of electronic components, it is required that 1-1/2 (3.8 cm) or more open space remains
between the bottom of the cooktop and any shelf underneath. The maximum length of the shelf
underneath is 18” (45.7 cm). It is required that the exit air ports at the front are not blocked, otherwise
elements may begin to cycle down during heavy usage.
14
-
(36 1/4”
.2 c
m) 14-1
(36 /4”
.2 c
m)
(10 4
.2 ”
(to cm) m
ek a
ick x.
)
1-1/2”
(3.8 cm) min.
28
(72-1/2
.4 ”
cm
)
18”
(45.7 cm) max.
30”W. Cooktop (VICU206) over
30”W. Electric Oven (VESO130/530)
”
1 4
.5
(2
to
2
cm
to
6
” )
/2 cm
-1 .35
(8
(
Optimum Design
Good Design
(4
”
/8 )
-3 cm
7
1 4.2
(91”min
.4 .
cm
)
”
/8 )
-3 cm
4
3 7.3
8” )
-1/ cm
1948.6
36
28
(4
”
/8 )
-3 cm
7
1 4.2
(73-3/4
.0 ”
cm
)
3.2
cm
)
(10
36”W. Cooktop (VICU266) over
36”W. Electric Oven (VESO166)
Hot Air
Hot Air
1
(4 7”
.2 4”
(to cm) m
ek a
ick x.
)
Cool Air
Cool Air
1
(43 7”
.2 c
m)
Oven Design
3
(86 4”
.4
cm
)
Hot Air
Cool Air
*Cooktops installed over an oven are not considered optimal design. During periods of heavy usage,
Note: Refer to the oven installation instructions for undercounter dimensions.
8
powering down randomly of some units can be expected.
9
Cutout Dimensions
Clearance Dimensions
Proximity to Side Cabinet Installation
30” W. CUTOUT w/
DOWNDRAFT
7/8”
(2.2 cm)
27”
(68.6 cm)
7/8”
(2.2 cm)
2-1/4”
(5.7 cm)
20-1/4”
(51.4 cm)
28-3/4”
(73.0 cm)
Minimum Clearances from Adjacent
Combustible Construction
• The cooktop may be installed directly to
existing base cabinets.
• The cooktop CANNOT be installed directly
adjacent to sidewalls, tall cabinets, tall
appliances, or other side vertical surfaces
above 36” (91.4 cm) high. There must be a
minimum of 6” (15.2 cm) side clearance from
the cooktop to such combustible surfaces
above the 36” (91.4 cm) counter height.
• Within the 6” (15.2 cm) side clearance to
combustible vertical surfaces above
36” (91.4 cm), the maximum wall cabinet depth
must be 13” (33.0 cm) and wall cabinets within
this 6” (15.2 cm) side clearance must be 18”
(45.7 cm) above the 36” (91.4 cm) high
countertop.
• Wall cabinet above the cooktop must be a
minimum of 36” (91.4 cm) above the
countertop for a full width of the cooktop.
• If a ventilation hood is installed over the
cooktop, the minimum 36” (91.4 cm) height
clearance above the unit does not apply. Refer
to the hood installation instructions for further
information.
•
•
•
•
Above countertop 36” (91.4 cm) minimum
Side 6” (15.2 cm)
Rear 0” (0.0 cm)
Within 6” side clearance. Wall cabinets no
deeper than 13” (33.0 cm)
• Must be minimum 18” (45.7 cm) above
countertop
• Wall cabinets directly above the product must
be minimum 36” (91.4 cm) above the
countertop
.
ax
” mcm)
3
1 .0
(33
36” W. CUTOUT w/
DOWNDRAFT
(45
5
7/8”
(2.2 cm)
(91
(1
33”
(83.8 cm)
”m )
18 .7 cm
.
in )**
m m
” c
6 .2
7/8”
(2.2 cm)
in.
)*
”m
m
6
c
3 .4
in.
2-1/4”
(5.7 cm)
HO
REAR
T
FRON
T
HO
)
”
361.4 cm
REAR
T
FRON
T
(9
(
”
/8 m)
-1 c
3 .9
7
20-1/4”
(51.4 cm)
Dimensions shown are for use with
combustible surfaces unless otherwise
stated.
34-3/4”
(88.3 cm)
10
11
.
in )
m m
” c
0 0 .0
(
n.
mi
Electrical Requirements
WARNING
General Information
WARNING
ELECTRICAL
GROUNDING
INSTRUCTIONS
The electrical power to the
unit must be shut off while line
connections are being made.
Failure to do so could result
in serious injury or death.
This cooktop must be electrically
grounded in accordance with local codes
or, in the absence of codes, with the
National Electrical Code, ANSI/NFPA 70latest edition. FOR PERSONAL
SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
READ AND FOLLOW ALL WARNING
AND CAUTION INFORMATION WHEN
INSTALLING THIS APPLIANCE.
• When removing the cooktop for service
and/or cleaning, disconnect AC power
supply.
• Electrical requirements are listed in the
product specifications under the “Electrical
Requirements” section.
• Keep appliance area clear and free from
combustible materials, gasoline and other
flammable vapors.
• Disconnect the electrical supply prior to
servicing or cleaning.
Electrical Connection
When making the wire connections, use
the entire length of the conduit provided
(3 feet). The conduit must not be cut.
Connect the red and black leads from the
unit conduit to the corresponding leads in
the junction box. The bare ground wire in the
conduit is connected to the unit frame. When
connecting to a 3-conductor branch circuit,
connect the bare ground connector lead of
the unit to the branch circuit ground (bare
wire or green in color).
Electrical Requirements
Check your local codes regarding this unit.
This cooktop is supplied with a 3-wire, A.C.
208V/120 volt or 120V/240 volt, 60 HZ
electrical system. A white (neutral) is not
needed for this unit. See next section for
grounding instructions. It should be fused
separately.
Installation
1
2
HO
T
REAR
FRONT
HO
REAR
Green
Ground
T
FRONT
Red
Black
WARNING
FIRE AND ELECTRICAL
SHOCK HAZARD
CAUTION
Be sure the electric power is
off from the breaker box to the
junction box until the cooktop
is installed and ready to
operate. The junction box should be
connected to a suitable ground.
DO NOT use an extension
cord with this appliance. Such
use may result in fire, electrical
shock, or other personal injury.
Refer to the specifications chart for kilowatt
rating and recommended amperage. House
wiring and fusing must comply with local
codes. If no local codes are applicable, wire
in accordance with the National Electrical
Code, ANSI/NFPA 70-latest edition.
Lower cooktop into cutout.
Connect the red and black leads from the unit conduit
to the corresponding leads in the junction box.
4
3
HO
T
HO
T
REA
R
REA
R
FRO
FRO
NT
NT
HO
T
HO
T
REA
R
REA
R
FRO
FRO
NT
NT
Countertop
Cooktop
Bracket
Screw brackets to burner box with sheet metal screw.
(Two bracket assemblies included)
12
Screw sheet metal screws into brackets
and tighten firmly against bottom of countertop.
Note: Be careful not to crack or damage
counter by overtightening.
13
Final Preparation
• Some stainless steel parts may have a
plastic protective wrap which must be
peeled off.
• All stainless steel body parts should be
wiped with hot, soapy water and with a
liquid cleaner designed for this material.
If buildup occurs, DO NOT use steel wool,
abrasive cloths, cleaners, or powders!
Service & Registration
• If it is necessary to scrape stainless steel
to remove encrusted materials, soak with
hot, wet cloths to loosen the material,
then use a wood or nylon scraper.
DO NOT use a metal knife, spatula, or
any other metal tool to scrape stainless
steel! Scratches are almost impossible
to remove.
Performance Checklist
A qualified installer should carry out the
following checks:
Only authorized replacement parts may be used in performing service on the cooktop. DO
NOT repair or replace any part of the appliance unless specifically recommended in the
manual. All other servicing should be referred to a qualified technician.
Contact Viking Range Corporation, 1-888-VIKING1 (845-4641), for the nearest service parts
distributor in your area or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Cooktop – The serial number and model number for your appliance can be found by looking
under the unit.
2. Place an induction compatible piece of
cookware onto the left front burner–Left
front indicator should be solid.
3. Remove cookware and repeat steps for
other elements.
I Check top surface elements
1. Starting with the left front element, turn
the corresponding knob to the Hi
position–Left front indicator should flash.
Record the following information indicated below. You will need it if service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
Dealer's name _____________________________________________________________________________________
Address ___________________________________________________________________________________________
These installation instructions should remain with the unit
for future reference.
14
15