Biostar Hi-Fi A55S2 Owner's Manual

Hi-Fi A85S2/Hi-Fi A75S2/Hi-Fi A55S2 Setup Manua l

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.

Dichiarazione di conformità sintetica

Ai sensi dell’art. 2 comma 3 del D.M.

275 del 30/10/2002

Si dichiara che questo prodotto è conforme alle normative vigenti e soddisfa i requisiti essenziali richiesti dalle direttive

2004/108/CE, 2006/95/CE e

1999/05/CE quando ad esso applicabili

Short Declaration of conformity

We declare this product is complying with the laws in force and meeting all the essential requirements as specified by the directives

2004/108/CE, 2006/95/CE and

1999/05/CE whenever these laws may be applied

Table of Contents

Chapter 1: Introduction ...............................................................1

1.1

1.2

1.3

1.4

1.5

Before You Start......................................................................... 1

Package Checklist ..................................................................... 1

Motherboard Specifications ....................................................... 2

Rear Panel Connectors ............................................................. 4

Motherboard Layout .................................................................. 5

Chapter 2: Hardware Installation................................................6

2.1

Install Central Processing Unit (CPU) ....................................... 6

2.2

2.3

2.4

2.5

2.6

2.7

Install a Heatsink ....................................................................... 7

Connect Cooling Fans............................................................... 8

Install System Memory .............................................................. 9

Expansion Slots........................................................................11

Jumper Setting ........................................................................ 12

Headers & Connectors ............................................................ 13

Chapter 3: UEFI BIOS & Software.............................................19

3.1

UEFI BIOS Setup .................................................................... 19

3.2

3.3

BIOS Update ........................................................................... 19

Software................................................................................... 24

Chapter 4: Useful Help ..............................................................27

4.1

Driver Installation..................................................................... 27

4.2

4.3

4.4

4.5

AMI BIOS Beep Code.............................................................. 28

Troubleshooting....................................................................... 28

RAID Functions ....................................................................... 30

AMD Dual Graphics Technology ............................................. 34

Appendix: Specifications In Other Languages .......................36

Arabic ......................................................................................................... 36

French ........................................................................................................ 38

German....................................................................................................... 40

Italian .......................................................................................................... 42

Japanese .................................................................................................... 44

Polish.......................................................................................................... 46

Portuguese ................................................................................................. 48

Russian....................................................................................................... 50

Spanish....................................................................................................... 52

Hi-Fi A85S2/Hi-Fi A75S2/Hi-Fi A55S2

CHAPTER 1: INTRODUCTION

1.1 Before You Start

Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:

Prepare a dry and stable working environment with sufficient lighting.

Always disconnect the computer from power outlet before operation.

Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.

Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board.

Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment.

Keep the computer from dangerous area, such as heat source, humid air and water.

The operating temperatures of the computer should be 0 to

45 degrees Celsius.

To avoid injury, be careful of:

Sharp pins on headers and connectors

Rough edges and sharp corners on the chassis

Damage to wires that could cause a short circuit

; Serial ATA Cable x2

; Rear I/O Panel for ATX Case x1

; User’s Manual x1

; Fully Setup Driver DVD x1

Note: The package contents may be different due to the sales region or models in which it was sold. For more information about the standard package in your region, please contact your dealer or sales representative.

1

Motherboard Manual

CPU Support

Chipset

Memory

Storage

LAN

Audio Codec

USB

Expansion Slots

Rear I/Os

Specifications

Socket FM2 for AMD A-series processor

Maximum CPU TDP (Thermal Design Power): 100Watt

* Please refer to www.biostar.com.tw

for CPU support list.

AMD A85 FCH (Hi-Fi A85S2)



Supports Dual Channel DDR3 800/ 1066/ 1333/ 1600/ 1866

2 x DDR3 DIMM Memory Slot, Max. Supports up to 32 GB Memory

Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 module

* Please refer to www.biostar.com.tw

for Memory support list.

AMD A85/A75/A55 FCH

Supports RAID 0,1,10, 5 & AHCI (AMD A85 FCH)

Supports RAID 0,1,10, & AHCI (AMD A75/A55 FCH),

Realtek RTL 8111F

10/ 100/ 1000 Mb/s auto negotiation, Half / Full duplex capability

ALC892

5.1 Channels, High Definition Audio, Biostar Hi-Fi

AMD A85/A75 FCH:

6x USB 2.0 port (2 on rear I/Os and 4 via internal headers)


AMD A55 FCH:


3x PCI Slot

2x PCIe 2.0 x1 Slot

1x PCIe 2.0 x16 Slot

Hi-Fi A85S2:

1x PS/2 Mouse

1x PS/2 Keyboard

1x HDMI Port

1x VGA Port

1x DVI Port

1x LAN port

2x USB 2.0 Port

2x USB 3.0 Port

3x Audio Jack

Hi-Fi A75S2:

1x PS/2 Mouse

1x PS/2 Keyboard

1x HDMI Port

1x VGA Port

1x DVI Port

1x LAN port

2x USB 2.0 Port

2x USB 3.0 Port

3x Audio Jack

Hi-Fi A55S2:

1x PS/2 Mouse

1x PS/2 Keyboard

1x VGA Port

1x DVI Port

1x LAN port

4x USB 2.0 Port

3x Audio Jack

2

Internal I/Os

Form Factor

OS Support


Specifications

Hi-Fi A85S2:

8x SATA 6.0Gb/s Connector

2x USB 2.0 Header

1x USB 3.0 Header

1x 4-Pin Power Connector


1x CPU Fan Connector

2x System Fan Connector

1x Front Panel Header

1x Front Audio Header

1x Clear CMOS Header

1x Printer Port Header

1x Consumer IR Header

1x Serial Port Header

1x S/PDIF out Connector

Hi-Fi A75S2:


2x USB 2.0 Header

1x USB 3.0 Header












Hi-Fi A55S2:


2x USB 2.0 Header












ATX Form Factor, 295 mm x 200 mm

Windows XP / Vista / 7/ 8

Biostar reserves the right to add or remove support for any OS with or without notice.

3


1.4 Rear Panel Connectors

Hi-Fi A85S2 / Hi-Fi A75S2

Hi-Fi A55S2

Note 1: HDMI / DVI-D / VGA Output require an AMD family processor with intedrated graphics.

Note 2: The mainboard supports three independent display outputs except Hi-Fi A55S2.

Note 3: Since the audio chip supports High Definition Audio Specification, the function of each audio jack can be defined by software. The input / output function of each audio jack listed above represents the default setting. However, when connecting external microphone to the audio port, please use the Line In (Blue) and Mic In (Pink) audio jack.

Note 4: Maximum resolution:

Outputs

HDMI

DVI-D

VGA

Maximum resolution

1920 x 1080 @60Hz

1920 x 1200 @60Hz

1920 x 1200 @60Hz

2560 x 1600 @60Hz

1920 x 1600 @60Hz

Bit Depth

24, 30, 36 bpp

24 bpp

30 bpp

24 bpp

--

4


Note1: ■ represents the 1st pin.

Note2: SATA7 & SATA8 are only for Hi-Fi A85S2.

5


CHAPTER 2: HARDWARE INSTALLATION

2.1 Install Central Processing Unit (CPU)

Step 1: Locate the CPU socket on the motherboard

Step 2: Pull the socket locking out from the socket and then raise the lever up to a 90-degree angel.

6

Step 3: Look for the white triangle on socket, and the gold triangle on CPU should point towards this white triangle. The CPU will fit only in the correct orientation.

Note: The CPU fits only in one correct orientation. Do not force the CPU into the socket to prevent damaging the CPU.


Step 4: Hold the CPU down firmly, and then close the lever to locked the position

Step 1: Place the heatsink and fan assembly onto the retention frame. Match the heatsink clip with the socket mounting-lug. Hook the spring clip to the mounting-lug.

Step 2: On the other side, push the retention clip straight down to lock into the plastic lug on the retention frame, and then press down the locker until it stops.

Note1: Do not forget to connect the CPU fan connector.

Note2: For proper installation, please kindly refer to the installation manual of your CPU heatsink.

7


These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.

CPU_FAN1: CPU Fan Header

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

4 Smart Fan Control

(By Fan)

SYS_FAN1/SYS_FAN2: System Fan Header

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

Note: CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.

8

A. DDR3 Modules


Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.

Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

9


B. Memory Capacity

DIMM Socket Location DDR3 Module

DDR3_A1 512MB/1GB/2GB/4GB/8GB/16GB

DDR3_B1 512MB/1GB/2GB/4GB/8GB/16GB

Total Memory Size

Max is 32GB.

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DDR3_A1 DDR3_B1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

Note: The DRAM bus width of the memory module must be the same (x8 or x16)

10


PEX16_1: PCI-Express Gen2 x16 Slot

-

-

-

PCI-Express 2.0 compliant.

Maximum theoretical realized bandwidth of 8GB/s simultaneously per direction, for an aggregate of 16GB/s totally.

PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slot

-

-

PCI-Express 2.0 compliant.

Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total

PCI1/ PCI2/ PCI3: Peripheral Component Interconnect Slot

This motherboard is equipped with 1 standard PCI slot. PCI stands for Peripheral

Component Interconnect, and it is a bus standard for expansion cards.

Install an Expansion Card

4.

5.

6.

You can install your expansion card by following steps:

1. Read the related expansion card's instruction document before install the expansion card into the computer.

2.

3.

Remove your computer's chassis cover, screws and slot bracket from the computer.

Place a card in the expansion slot and press down on the card until it is completely seated in the slot.

7.

Secure the card’s metal bracket to the chassis back panel with a screw.

Replace your computer's chassis cover.

Power on the computer, if necessary, change BIOS settings for the expansion card.

Install related driver for the expansion card.

11


The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”.

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard.

1 3

Pin 1-2 Close:

Normal Operation (default).

1 3

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1.

2.

3.

4.

Remove AC power line.

Set the jumper to “Pin 2-3 close”.

Wait for five seconds.

Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Load Optimal Defaults and save settings in CMOS.

12


2.7 Headers & Connectors

ATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX power supply.

Pin Assignment

13 +3.3V

14 -12V

15 Ground

16 PS_ON

17 Ground

18 Ground

19 Ground

20 NC

21 +5V

22 +5V

23 +5V

24 Ground

Pin Assignment

1 +3.3V

2 +3.3V

3 Ground

4 +5V

5 Ground

6 +5V

7 Ground

8 PW_OK

10 +12V

11 +12V

12 +3.3V

ATXPWR2: ATX Power Source Connector

This connector will provide +12V to CPU power circuit.

Pin Assignment

1 +12V

2 +12V

3 Ground

4 Ground

Note1: Before you power on the system, please make sure that both ATXPWR1 and

ATXPWR2 connectors have been plugged-in.

Note2: Insufficient power supplied to the system may result in instability or the peripherals not functioning properly. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices.

13


PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.

14

Pin Assignment Function Pin

1 +5V

2 N/A

3 N/A

Speaker

Connector

10

11

Assignment

9 N/A

N/A

N/A

Function

N/A

N/A

4 Speaker 12 Power LED (+)

5

6

HDD LED (+)

HDD LED (-)

Hard drive LED

13

14

Power LED (+)

Power LED (-)

Power LED

7 Ground

Reset button

15

16 Ground

SATA1~SATA8: Serial ATA Connectors

These connectors connect to SATA hard disk drives via SATA cables.

Hi-Fi A85S2 & Hi-Fi A75S2 satisfy the SATA 3.0 spec and with transfer rate of 6.0Gb/s.

Hi-Fi A55S2 satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

SATA7 & SATA8 are only for Hi-Fi A85S2.

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

7 Ground


JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel, and also can be connected with a wide range of simultaneously accessible external Plug and Play peripherals.

Pin Assignment Pin

1 VBUS0

Assignment

11 D2+

2 SSRX1-

3 SSRX1+

4 Ground

12 D2-

13 Ground

14 SSTX2+

5 SSTX1-

6 SSTX1+

7 Ground

8 D1-

9 D1+

10 ID

15 SSTX2-

16 Ground

17 SSRX2+

18 SSRX2-

19 VBUS1

20 Key

Note: The USB 3.0 header is only for Hi-Fi A85S2 and Hi-Fi A75S2

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel, and also can be connected with a wide range of simultaneously accessible external Plug and Play peripherals.

Pin Assignment

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 NC

10 Key

15


F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front panel. This header supports HD and AC’97 audio front panel connector.

16

HD Audio

Pin Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

Sense

Sense

8

9

Key

Left line in

AC’97

Pin Assignment

1 Mic In

2 Ground

3 Mic Power

5 RT Line Out

7 Reserved

8 Key

9 LFT Line Out

Note1: It is recommended that you connect a high-definition front panel audio module to this connector to avail of the motherboard's high definition audio capability.

Note2: Please try to disable the "Front Panel Jack Detection" if you want to use an

AC'97 front audio output cable. The function can be found via O.S. Audio Utility.

JSPDIFOUT1: Digital Audio-out Connectors

The JSPDIFOUT1 is for connecting the PCI bracket SPDIF output.

3

1

2

Pin Assignment

+5V

SPDIF_OUT

Ground


J_COM1: Serial Port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Pin Assignment

5

6

7

1

2

3

4

Carrier detect

Received data

Transmitted data

Data terminal ready

Signal ground

Data set ready

Request to send

10 NC

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data

0 16 Ground

6 -Init 19 -ACK

8 -Scltin 21 Busy

3 22 Ground

10 Ground 23 PE

12 Ground 25 SCLT

13 Data Key

17


CIR1: Consumer IR Connector

This header is for infrared remote control and communication.

Pin Assignment

1 IrDA serial input

2 Ground

3 Ground

4 Key

5 IrDA serial output

18


CHAPTER 3: UEFI BIOS & SOFTWARE

3.1 UEFI BIOS Setup

For better system performance, the UEFI BIOS firmware is being continuously updated. The UEFI BIOS information described below in this manual is for your reference only and the actual UEFI BIOS information and settings on board may be different from this manual

For further information of setting up the UEFI BIOS, please refer to the

UEFI BIOS Manual in the Setup DVD.

There are three ways to update the BIOS:

BIOS Update Utility, BIOS Online Update Utility and BIOS Flasher.

1. BIOS Update Utility

1. Installing BIOS Update Utility from the DVD Driver.

2. Download the proper BIOS from www.biostar.com.tw

.

3. Open BIOS Update Utility and click the Update BIOS button on the main screen.

4. A warning message will show up to request your agreement to start the BIOS update. Click OK to start the update procedure.

5. Choose the location for your

BIOS file in the system. Please select the proper BIOS file, and then click on Open. It will take several minutes, please be patient.

19


6. After the BIOS Update process is finished, click on OK to reboot the system.

7. While the system boots up and the full screen logo shows up, please press the <Delete> key to enter BIOS setup.

After entering the BIOS setup, please go to the Save & Exit, using the Restore

Defaults function to load Optimized Defaults, and select Save Changes and

Reset to restart the computer. Then, the BIOS Update is completed.

Backup BIOS

Click the Backup BIOS button on the main screen for the backup of BIOS, and select a proper location for your backup BIOS file in the system, and click Save.

20


2. Online Update Utility

1. Installing BIOS Update Utility from the DVD Driver.

2. Please make sure the system is connected to the internet before using this function.

3. Open BIOS Update Utility and click the Online Update button on the main screen.

4. An open dialog will show up to request your agreement to start the BIOS update. Click

Yes to start the online update procedure.

5. If there is a new BIOS version, the utility will ask you to download it. Click Yes to proceed.

6. After the download is completed, you will be asked to program (update) the BIOS or not. Click Yes to proceed.

7. After the updating process is finished, you will be asked you to reboot the system. Click OK to reboot.

21


8. While the system boots up and the full screen logo shows up, press

<Delete> key to enter BIOS setup.




3. BIOSTAR BIOS Flasher

BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive.

Note1: This utility only allows storage device with FAT32/16 format and single partition.

Note2: Shutting down or resetting the system while updating the BIOS will lead to system boot failure.

The BIOSTAR BIOS Flasher is built in the BIOS ROM. To enter the utility, press

<F12> during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIOSTAR BIOS Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, copy and save the BIOS file into a USB flash (pen) drive.

3. Insert the USB pen drive that contains the BIOS file to the USB port.

4. Power on or reset the computer and then press <F12> during the POST process.

5. After entering the POST screen, the BIOS-FLASHER utility pops out. Choose [fs0] to search for the BIOS file.

22


6. Select the proper BIOS file, and a message asking if you are sure to flash the BIOS file.

Click Yes to start updating

BIOS.

7. A dialog pops out after BIOS flash is completed, asking you to restart the system. Press the

[Y] key to restart system.

8. While the system boots up and the full screen logo shows up, press

<Delete> key to enter BIOS setup.




23


3.3 Software

Installing Software

1. Insert the Setup DVD to the optical drive. The driver installation program would appear if the Autorun function has been enabled.

2. Select Software Installation, and then click on the respective software title.

3. Follow the on-screen instructions to complete the installation.

Note1: All the information and content about following software are subject to be changed without notice. For better performance, the software is being continuously updated.

Note2: The information and pictures described below are for your reference only. The actual information and settings on board may be slightly different from this manual.

Launching Software

After the installation process is completed, you will see the software icon showing on the desktop. Double-click the icon to launch it.

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem.

Note: Before you use this utility, please set Outlook Express as your default e-mail client application program.

* must provide. Without this information, you may not be able to send out the mail.

This block will show the information which would be collected in the mail.

* Describe condition of your system.

* Select your area or the area close to you.

Provide the e-mail address that you would like to send the copy to.

* Provide the name of the memory module manufacturer.

Send the mail out.

Exit this dialog.

Save these information to a .txt file

Provide the name of the power supply manufacturer and the model no.

24


After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click

“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name.

Enter the file name and then click “Save”.

Your system information will be saved to a .txt file.

Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail.

Note1: We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service.

Note2: If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application. Go to the following web http://www.biostar.com.tw/app/en/about/contact.php

for getting our contact information.

25


Smart EAR

Smart EAR is a windows-based audio utility which allows you to easily adjust system volume. With its user-friendly GUI, you can also adjust impedance setting (Low/High Gain) to optimize your headphone performance. z High/Low Gain Switch: Keep the gain switch to low for low impedance headphone and set to high for high impedance headphone. z Mute Button: To disable system sound z Volume Control Knob: The volume can be finely adjusted by turning the knob either clockwise or anti-clockwise to increase or decrease system volume accordingly. z Information Button: Get information of the application z Minimize Button: Minimize the application window to the taskbar z Exit Button: Exit the application

Note:

1. Smart EAR is only supported by Windows 7/8 and BIOSTAR Hi-Fi series motherboards.

2. High/Low Gain Switch is only for “Front Panel Audio Header”, please make sure you are connecting your headphone to the front panel I/O.

26


CHAPTER 4: USEFUL HELP

After you installed your operating system, please insert the Fully Setup Driver

DVD into your optical drive and install the driver for better system performance.

You will see the following window after you insert the DVD

The setup guide will auto detect your motherboard and operating system.

Note: If this window didn’t show up after you insert the Driver DVD, please use file browser to locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver DVD.

Click on the Manual icon to browse for available manual.

Note: You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://get.adobe.com/reader/

27


4.2 AMI BIOS Beep Code

Boot Block Beep Codes

Number of Beeps

Continuing

Description

Memory sizing error or Memory module not found

POST BIOS Beep Codes

Number of Beeps Description

8 Display memory error (system video adapter)

4.3 Troubleshooting

Probable Solution

1. There is no power in the system.

Power LED does not shine; the fan of the power supply does not work

1. Make sure power cable is securely plugged in.

2. Indicator light on keyboard does not shine.

3. Contact technical support.

System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running.

Using even pressure on both ends of the

DIMM, press down firmly until the module snaps into place.

System does not boot from a hard disk drive, but can be booted from optical drive.

1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard

CMOS setup.

2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time.

System only boots from an optical drive. Hard disks can be read, applications can be used, but system fails to boot from a hard disk.

Screen message shows “Invalid

Configuration” or “CMOS Failure.”

System cannot boot after user installs a second hard drive.

1. Back up data and applications files.

2. Reformat the hard drive. Re-install applications and data using backup disks.

Review system’s equipment. Make sure correct information is in setup.

1. Set master/slave jumpers correctly.

2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.

28


CPU Overheated

If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.

(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

29


Operating System

Supports Windows Vista , Windows 7 and Windows 8.

Raid Arrays

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.

RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity.

RAID Definitions

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the platform.

Uses: Intended for non-critical data requiring high data throughput, or any environment that does not require fault tolerance.

Benefits: provides increased data throughput, especially for large files. No capacity loss penalty for parity.

Drawbacks: Does not deliver any fault tolerance. If any drive in the array fails, all data is lost.

Fault Tolerance: No.

Total Capacity: (Minimal. HDD Capacity) x (Connected HDDs Amount)

30

Block 1

Block 3

Block 5

Block 2

Block 4

Block 6


RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a

RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure.

RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media.


Drives: Minimum 2, and maximum is 2.

Uses: RAID 1 is ideal for small databases or any other application that requires fault tolerance and minimal capacity.

Benefits: Provides 100% data redundancy. Should one drive fail, the controller switches to the other drive.

Drawbacks: Requires 2 drives for the storage space of one drive.

Performance is impaired during drive rebuilds.

Fault Tolerance: Yes.

Block 1

Block 2

Block 3

Block 1

Block 2

Block 3

31


RAID 10:

RAID 1 drives can be stripped using RAID 0 techniques.Resulting in a RAID 10 solution for improved resiliency, performance and rebuild performance.


Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.

Benefits: Optimizes for both fault tolerance and performance, allowing for automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks.

Drawbacks: Requires twice the available disk space for data redundancy, the same as RAID level 1.


Block 1

Block 3

Block 5

Block 1

Block 3

Block 5

Block 2

Block 4

Block 6

Block 2

Block 4

Block 6

32


RAID 5:

RAID 5 stripes both data and parity information across three or more drives. It writes data and parity blocks across all the drives in the array. Fault tolerance is maintained by ensuring that the parity information for any given block of data is placed on a different drive from those used to store the data itself.

Note: The RAID 5 function is supported by A85 chipset only.


Drives: Minimum 3.

Uses: RAID 5 is recommended for transaction processing and general purpose service.

Benefits: An ideal combination of good performance, good fault tolerance, and high capacity and storage efficiency.

Drawbacks: Individual block data transfer rate same as a single disk. Write performance can be CPU intensive.


Disk 1

DATA 1

DATA 3

PARITY

DATA 7

DATA 9

PARITY

Disk 2

DATA 2

PARITY

DATA 5

DATA 8

PARITY

DATA 11

Disk 3

PARITY

DATA 4

DATA 6

PARITY

DATA 10

DATA 12

33


4.5 AMD Dual Graphics Technology

AMD Dual Graphics Technology Introduction

When user adds a PCIE display adapter, it can be integrated with IGD to show better performance. To make the two video devices work simultaneously and normally, please refer to the following setting.

AMD Dual Graphics Requirement

Operating System: Windows Vista / Windows 7 / Windows 8

Supported Dual Graphics Combinations:

AMD Radeon ™ Graphics Card

HD 6670

HD 6570

A10-Series

HD 7660D

●

●

HD 6450

● Recommended graphics cards for AMD dual-graphics

A8-Series

HD7560D

●

●

A6-Series

HD 7540D

●

●

Note 1: A4-Series products do not support Dual Graphics.

Note 2: The information described above in this manual is for your reference only and the actual information and settings on board may be different from this manual. For further AMD

Dual Graphics information, please visit the following website: http://www.amd.com

34


AMD Dual Graphics Setup

Step 1: Insert Dual Graphics-Ready graphics card into PEX16_1 slot.

Step 2: Set the BIOS setting as follows:

[Chipset]→[North Bridge]→[GFX Configuration]

→[Surround View]→[Enabled]

Step 3: Install Driver DVD Chipset Driver, and reboot the system. Activate

AMD VISION Engine Control Center to make sure CrossFire has been enabled.

35


APPENDIX: Specifications In Other Languages

Arabic

تﺎﻔﺻاﻮﻤﻟا

A ﻞﺴﻠﺴﺗ AMD ىد مإ ﻪﻳا ﺞﻟﺎﻌﻤﻟ FM 2 ﺬﺧﺄﻤﻟا

.

طاو 100 :( thermal design power – TDP ) ﺞﻟﺎﻌﻤﻟا ﻢﻴﻤﺼﺗ ﻲﻓ ﺔﻳراﺮﺤﻟا ﺔﻗﺎﻄﻠﻟ ﻰﺼﻗﻷا ﺪﺤﻟا

.

CPU ﺞﻟﺎﻌﻤﻟا ﻢﻋد ﺔﻤﺋﺎﻘﻟ www.biostar.com.tw

ﻊﻗﻮﻤﻟا ﻰﻟإ عﻮﺟﺮﻟا ﻰﺟﺮﻳ *




1866 / 1600 / 1333 / 1066 / 800 DDR3 .

را .

يد .

يد ﺔﺟودﺰﻣ ةﺎﻨﻗ ﻢﻋﺪﺗ

ةﺮآاذ ﺖﻳﺎﺑﺎﺠﻴﺟ 32 ﻰﺼﻗأ ﺪﺤآ ﻞﻤ ﺤﺘﺗ ، DIMM ﺔﺟودﺰﻤﻟا ةﺮآاﺬﻟا تﺎﺤﺘﻓ DDR3 .

را .

يد .

يد x 2

DDR3 را .

يد .

يد ﺖﻳﺎﺑﺎﺠﻴﺟ 16 / 8 / 4 / 2 / 1 / ﺖﻳﺎﺑ ﺎﺠﻴﻣ 512 ECC نود ﻞﻤﺤﺘﺗ DIMM ﺔﺟودﺰﻣ ﺔﺤﺘﻓ ﻞآ

.

ةﺮآاﺬﻟا ﻢﻋد ﺔﻤﺋﺎﻘﻟ www.biostar.com.tw

ﻊﻗﻮﻤﻟا ﻰﻟإ عﻮﺟﺮﻟا ﻰﺟﺮﻳ *

FCH A85/A75/A55 AMD ىد مإ ﻪﻳا

(FCH A85) AHCI / 10 / 1 / 0 / 5 RAID ﺪﻳار ﻞﻤﺤﺘﺗ

(FCH A75/A55) AHCI / 10 / 1 / 0 RAID ﺪﻳار ﻞﻤﺤﺘﺗ

REALTEK RTL 8111F ل تر ﻚﻴﺘﻟﺎﻴﻳر

ﺔﺟودﺰﻤﻟا ىﻮﺼﻘﻟا ةرﺪﻘﻟا / ﻒﺼﻨﻟا ، ﻲﺋﺎﻘﻠﺗ ﺪﻳﺪﺤﺗ ، ﺔﻴﻧﺎﺜﻟا / ﺖﻳﺎﺑﺎﺠﻴﻣ 1000 / 100 / 10

ALC892

Biostar Hi-Fi , ﺔﻗﺪﻟا ﺔﻴﻟﺎﻋ تاﻮﻨﻗ 5.1

FCH AMD A85/A75 ىد مإ ﻪﻳ

( ﻲﻠﺧاﺪﻟا عزﻮﻤﻟا لﻼﺧ ﻦﻣ 4 و ﺔﻴﻔﻠﺨﻟا جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤﻟا ﻲﻓ 2 ) 2.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ 6 x ﺬﻓﺎﻨﻣ


USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ 4 x ﺬﻓﺎﻨﻣ

FCH AMD A55 ىد مإ ﻪﻳ


USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ 8 x ﺬﻓ ﺎﻨﻣ

PCI ﺔﻴﻓﺎﺿﻹا تﺎﻘﺤﻠﻤﻟا ﺬﻔﻨﻣ ﺔﺤﺘﻓ x 3

1 x2.0

PCIe ﺔﻴﻓﺎﺿﻹا تﺎﻘﺤﻠﻤﻟا ﺬﻔﻨﻣ ﺔﺤﺘﻓ x 2

16 x 2.0

PCIe ﺔﻴﻓﺎﺿﻹا تﺎﻘﺤﻠﻤﻟا ﺬﻔﻨﻣ ﺔﺤﺘﻓ x 1

Hi-Fi A55S2

ةرﺎﻔﻟا PS/2 x 1

تﻮﻴﺒﻤﻜﻠﻟ ﺢﻴﺗﺎﻔﻤﻟا ﺔﺣﻮﻟ PS/2 x 1

VGA ﻲﺋﺮﻤﻟا ضﺮﻌﻟا ﺔﻣﻮﻈﻨﻣ x 1 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

DVI ﺔﻴﻤﻗر ﺔﻴﺋﺮﻣ ﺔﻬﺟاو x 1 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

LAN ﺔﻴﻠﺤﻤﻟا ﺔﻜﺒﺸﻟا x 1 دﺪﻋ ﻞﻴﺻﻮﺘﻟ ﺔﺤﺘﻓ

2.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x 4 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

تﻮﺼﻠﻟ كﺎﺟ x 3 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

Hi-Fi A85S2/ Hi-Fi A75S2

LAN ﺔﻴﻠﺤﻤﻟا ﺔﻜﺒﺸﻟا

ةرﺎﻔﻟا

تﻮﻴﺒﻤﻜﻠﻟ ﺢﻴﺗﺎﻔﻤﻟا ﺔﺣﻮﻟ

PS/2 x

PS/2

1 x 1

حﻮﺿﻮﻟا ﻲﻟﺎﻌﻟا دﺪﻌﺘﻣ ﻂﻴﺳو HDMI x 1 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

VGA ﻲﺋﺮﻤﻟا ضﺮﻌﻟا ﺔﻣﻮﻈﻨﻣ x 1 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

DVI ﺔﻴﻤﻗر ﺔﻴﺋﺮﻣ ﺔﻬﺟاو x 1 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ x 1 دﺪﻋ ﻞﻴﺻﻮﺘﻟ ﺔﺤﺘﻓ

2.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x 2 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔ ﺤﺘﻓ

3.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x 2 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

تﻮﺼﻠﻟ كﺎﺟ x 3 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ةﺪﻋﺎﻗ

ﺔﻳﺰآﺮﻤﻟا

ﺢﺋاﺮﺸﻟا ﺔﻋﻮﻤﺠﻣ

ةﺮآاﺬﻟا

ﻦﻳﺰﺨﺘﻟا

LAN ﺔﻴﻠﺤﻣ ﺔﻜﺒﺷ

ﻲﺗﻮﺼﻟا ﺰﻴﻣﺮﺘﻟا

مﺎﻋ ﻞﺴﻠﺴ ﺘﻣ ﻞﻗﺎﻧ

USB

ﻊﺳﻮﺘﻟا تﺎﺤﺘﻓ

جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤﻟا

ﺔﻴﻔﻠﺨﻟا

36


تﺎﻔﺻاﻮﻤﻟا

Hi-Fi A55S2

/ ﺖﻳﺎ ﺑﺎﺠﻴﺟ 3 x SATA 6 ﺔﻠﺻو

ﺔﻴﻧﺎﺜﻟا

مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x 2 عزﻮﻣ

2.0

USB

ﺲﻴﺑﺎﺑد 4 x 1 ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻﻮﻣ

سﻮﺑد 24 x 1 ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻو

ةﺪﺣو ﺪﻳﺮﺒﺗ ﺔﺣوﺮﻣ x 1 ﺔﻠﺻو

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا

ﺔﻣﻮﻈﻨﻤﻟا ﺪﻳﺮﺒﺗ حواﺮﻣ x2 ﺔﻠﺻو

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا x 1 عزﻮﻣ

ﻲﻣﺎﻣﻷا تﻮﺼﻟا x 1 عزﻮﻣ

ﺮﺷﺎﺒﻣ سﻮﻤﻴﺳ x 1 عزﻮﻣ

ﺔﻌﺑﺎﻄﻠﻟ ﺔﺤﺘﻓ x 1 عزﻮﻣ

IR ﻚﻠﻬﺘﺴﻣ x 1 عزﻮﻣ

ﺔﻴﻠﺴﻠﺴﺗ ﺔﺤﺘﻓ x 1 عزﻮﻣ

S/PDIF ﺔﻴﺟرﺎﺧ x 1 ﺔﻠﺻو

ﺔﻴﻤﻗﺮﻟا ﺔﻬﺟاﻮﻟا ﺲﺒﻴﻠﻴﻓ ﻲﻧﻮﺳ

Hi-Fi A75S2

/ ﺖﻳﺎﺑﺎﺠﻴﺟ 6 x SATA 6 ﺔﻠﺻو



2.0

USB

مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x1 عزﻮﻣ

3.0

USB

Hi-Fi A85S2

/ ﺖﻳﺎﺑﺎﺠﻴﺟ 6 x SATA 8 ﺔﻠﺻو



2.0

USB

مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x1 عزﻮﻣ

3.0

USB

ﺲﻴﺑﺎﺑد

سﻮﺑد

4 x

24

ةﺪﺣو ﺪﻳﺮﺒﺗ ﺔﺣوﺮﻣ

1 x

ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻﻮﻣ

1

ﺔﻳﺰآ

ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻو x

ﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا

ﺔﻣﻮﻈﻨﻤﻟا ﺪﻳﺮﺒﺗ حواﺮﻣ

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا x

1 x2

ﻲﻣﺎﻣﻷا تﻮﺼﻟا x

ﺮﺷﺎﺒﻣ سﻮﻤﻴﺳ x

ﺔﻌﺑﺎﻄﻠﻟ ﺔﺤﺘﻓ x

IR ﻚﻠﻬﺘﺴﻣ

ﺔﻴﻠﺴﻠﺴﺗ ﺔﺤﺘﻓ

S/PDIF ﺔﻴﺟرﺎﺧ

ﺔﻠﺻو

ﺔﻠﺻو

1 عزﻮﻣ

1

1

1

عزﻮﻣ

عزﻮﻣ

عزﻮﻣ x 1 عزﻮﻣ x 1 عزﻮﻣ x 1 ﺔﻠﺻو

ﺲﻴﺑﺎﺑد 4 x 1 ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻﻮﻣ

سﻮﺑد 24 x 1 ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻو

ةﺪﺣو ﺪﻳﺮﺒﺗ ﺔﺣوﺮﻣ x 1 ﺔﻠﺻو

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا

ﺔﻣﻮﻈﻨﻤﻟا ﺪﻳﺮﺒﺗ حواﺮﻣ x2 ﺔﻠﺻو

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا x 1 عزﻮﻣ

ﻲﻣﺎﻣﻷا تﻮﺼﻟا x 1 عزﻮﻣ

ﺮﺷﺎﺒﻣ سﻮﻤﻴﺳ x 1 عزﻮﻣ

ﺔﻌﺑﺎﻄﻠﻟ ﺔﺤﺘﻓ x 1 عزﻮﻣ

IR ﻚﻠﻬﺘﺴﻣ x 1 عزﻮﻣ

ﺔ ﻴﻠﺴﻠﺴﺗ ﺔﺤﺘﻓ x 1 عزﻮﻣ

S/PDIF ﺔﻴﺟرﺎﺧ x 1 ﺔﻠﺻو

ﺔﻴﻤﻗﺮﻟا ﺔﻬﺟاﻮﻟا ﺲﺒﻴﻠﻴﻓ ﻲﻧﻮﺳ ﺔﻴﻤﻗﺮﻟا ﺔﻬﺟاﻮﻟا ﺲﺒﻴﻠﻴﻓ ﻲﻧﻮﺳ

ﻢﻣ 200 x ﻢﻣ 295 ، ATX ﺔﻣﺪﻘﺘﻤﻟا ﺎﻴﺟﻮﻟﻮﻨﻜﺘﻟا دﺪﻣ ﻞﻜﺷ ﻞﻣﺎﻋ

8 زوﺪﻨﻳو / 7 زوﺪﻨﻳو / ﺎﺘﺴﻴﻓ زوﺪﻨﻳو / windows xp ﻲﺑ ﺲآإ زوﺪﻨﻳو

.

رﺎﻈﻧأ نوﺪﺑ وأ ﻊﻣ ﻞﻴﻐﺸﺗ مﺎﻈﻧ يﻷ ﻢﻋﺪﻟا ﺔﻟزأ وأ ﺔﻓﺎﺿإ ﻖﺤﺑ ﻆﻔﺘﺤﺗ BIOSTAR رﺎﺘﺳﻮﻴﺑ

جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤﻟا

ﺔﻴﻠﺧاﺪﻟا

ﻞﻜﺸﻟا ﻞﻣﺎﻋ

ﺔﻣﻮﻋﺪﻤﻟا ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻧأ

37


French

Support Unité

Centrale

Jeu de puces

Mémoire

Stockage

Réseau local

Codec audio

USB

Connecteur d’extension

I/O arrirèes

Spécifications

Interface de connexion FM2 pour série A AMD processeur

Enveloppe thermique Unité Centrale maximum : 100Watt

* Veuillez vous reporter à www.biostar.com.tw

pour la liste des supports modèles d'Unité Centrale.




Supporte mémoire DDR3 double canal 800/ 1066/ 1333/ 1600/ 1866

Banc de mémoire 2 x DDR3 DIMM, Supporte max. jusqu’à une mémoire de 32 GB

Chaque module DIMM supporte module DDR3 non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB

* Veuillez vous reporter à www.biostar.com.tw

pour la liste des soutien de la mémoire.

AMD A85/A75/A55 FCH

Supporte système RAID 0,1,10, 5 & AHCI (A85 FCH)

Supporte système RAID 0,1,10 & AHCI (A75/A55 FCH)

Realtek RTL 8111F

10/ 100/ 1000 Mb/s auto négociation, capacité bidirectionnelle à l'alternat / bidirectionnelle simultanée

ALC892

Canaux 5.1, écoute audio de haute définition, Biostar Hi-Fi

AMD A85/A75 FCH

Port 6x USB 2.0 (2 sur les I/O arrières et 4 en interne)


AMD A55 FCH


3x Fente PCI

2x PCIe 2.0 x1 Fente

1x PCIe 2.0 x16 Fente

Hi-Fi A85S2:

1x PS/2 Clavier

1x PS/2 Souris

1x Port HDMI

1x Port VGA

1x Port DVI

1x port LAN

2x Port USB 2.0

2x Port USB 3.0

3x entrées audio

Hi-Fi A75S2:

1x PS/2 Clavier

1x PS/2 Souris

1x Port HDMI

1x Port VGA

1x Port DVI

1x port LAN

2x Port USB 2.0

2x Port USB 3.0

3x entrées audio

Hi-Fi A55S2:

1x PS/2 Clavier

1x PS/2 Souris

1x Port VGA

1x Port DVI

1x port LAN

4x Port USB 2.0

3x entrées audio

38

I/O en interne

Support SE


Spécifications

Hi-Fi A85S2:

8x Connecteur SATA 6.0Gb/s

2x embases USB 2.0

1x embases USB 3.0

1x 4-Broche de carte


1x Connecteur ventilateur unité centrale

2x Connecteur ventilateur système

1x Fiche panneau avant

1x Fiche audio avant

1x Fiche mémoire CMOS vide

1x Embase port imprimante

1x Fiche Registre d’état

Consommateur

1x Embase port série

1x Connecteur sortie S/PDIF

Hi-Fi A75S2:


2x embases USB 2.0

1x embases USB 3.0










Consommateur



Hi-Fi A55S2:


2x embases USB 2.0










Consommateur



Facteur d'encombrement

Facteur d'encombrement ATX, 295 mm x 200 mm


Biostar se réserve le droit d’ajouter ou d'enlever le support pour toute SE avec ou sans préavis.

39


German

Spezifikationen

CPU-Unterstütz ung

Chipset

Arbeitsspeicher

LAN

Audio-Codec

USB

Erweiterungsan schlüsse

Hintere I/Os

Anschluss-FM2 für AMD A-Serie Prozessor

Maximale CPU TDP (Thermal Design Power): 100 Watt

* Bitte konsultieren Sie www.biostar.com.tw

für CPU-Unterstützungsliste




Festplattenspeic her

Unterstützt zweikanaliges DDR3 800/ 1066/ 1333/ 1600/ 1866

2 x DDR3 DIMM-SpeicherSlot, Max. Uterstützung bis zu 32 GB-Speicher

Jedes DIMM unterstützt nicht-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3-Module

* Bitte konsultieren Sie www.biostar.com.tw

für für Speicherunterstützung Liste.

AMD A85/A75/A55 FCH

Unterstützt RAID 0,1,10, 5 & AHCI (A85 FCH)

Unterstützt RAID 0,1,10 & AHCI (A75/A55 FCH)

Realtek RTL 8111F

10/ 100/ 1000 Mb Auto-Negotiation, Halb- / Voll-Duplex-fähig

ALC892

5.1 Kanäle, HD-Audio, Biostar Hi-Fi

AMD A85/A75 FCH:

6x USB 2.0-Port (2 hintere I/Os und 4 via interne Header)


AMD A55 FCH:


3x PCI-Slot

2x PCIe 2.0 x1-Slot

1x PCIe 2.0 x16-Slot

Hi-Fi A85S2:

1x PS/2-Maus

1x PS/2-Keyboard

1x HDMI-Port

1x VGA-Port

1x DVI-Port

1x LAN-Port

2x USB 2.0-Port

2x USB 3.0-Port

3x Audio Jack

Hi-Fi A75S2:

1x PS/2-Maus

1x PS/2-Keyboard

1x HDMI-Port

1x VGA-Port

1x DVI-Port

1x LAN-Port

2x USB 2.0-Port

2x USB 3.0-Port

3x Audio Jack

Hi-Fi A55S2:

1x PS/2-Maus

1x PS/2-Keyboard

1x VGA-Port

1x DVI-Port

1x LAN-Port

4x USB 2.0-Port

3x Audio Jack

40

Interne I/Os

Formfaktor

OS-Unterstützu ng


Spezifikationen

Hi-Fi A85S2:

8x SATA 6.0Gb/s-Verbinung

2x USB 2.0-Header

1x USB 3.0-Header

1x 4-Pin-Stromverbindung


1x CPU-Ventilatorverbindung

2x System-Ventilatorverbindung

1x Header für Frontpanel

1x Header für Frontaudio

1x Header für klares CMOS

1x Header für Druckerport

1x Consumer IR-Header

1x Serieller Port-Header

1x S/PDI-

Auswurfsverbindung

Hi-Fi A75S2:


2x USB 2.0-Header

1x USB 3.0-Header











1x S/PDI-

Auswurfsverbindung

Hi-Fi A55S2:


2x USB 2.0-Header











1x S/PDI-

Auswurfsverbindung

ATX Formfaktor, 295 mm x 200 mm


Biostar reserves the right to add or remove support for any OS with or without notice.

41


Italian

Specificazioni

Supporto processore

Tipo scheda

Slot FM2 per processore AMD serie-A

Alimentazione di Proiezione Termico (TDP – Thermal Design Power): 100Watt

* Si prega di consultare www.biostar.com.tw

per la lista di supporto del processore.




Memoria

Supporta DDR3 800/ 1066/ 1333/ 1600/ 1866 Doppio Canale

2 x DDR3 DIMM Slot di Memoria Supporta fino a 32 GB Memoria

Ogni DIMM supporta non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 moduli

* Si prega di consultare www.biostar.com.tw

per la lista di supporto del memoria.

Memorizzazione

Catena

Codec Audio

USB

AMD A85/A75/A55 FCH

Supporta RAID 0,1,10, 5 & AHCI (A85 FCH)

Supporta RAID 0,1,10 & AHCI (A75/A55 FCH)

Realtek RTL 8111F

10/ 100/ 1000 Mb auto negoziazione, capacita di duplex Meta / Completo

ALC892

Canali Audio di Alta Definizione 5.1, Biostar Hi-Fi

Piattaforma AMD A85/A75 FCH:

Slot 6x USB 2.0 (2 nei ingressi/ uscite posteriore e 4 da distributori interni)


Piattaforma AMD A55 FCH:


Slot 3x PCI

Slot di espansione

Ingressi/ Uscite

Posteriore

Slot 2x PCIe 2.0 x1

Slot 1x PCIe 2.0 x16

Hi-Fi A85S2:

Mouse 1x PS/2

Tastiera 1x PS/2

Slot 1x HDMI

Slot 1x VGA

Slot 1x DVI

Slot 1x LAN

Slot 2x USB 2.0

Slot 2x USB 3.0

Jack audio 3x

Hi-Fi A75S2:

Mouse 1x PS/2

Tastiera 1x PS/2

Slot 1x HDMI

Slot 1x VGA

Slot 1x DVI

Slot 1x LAN

Slot 2x USB 2.0

Slot 2x USB 3.0

Jack audio 3x

Hi-Fi A55S2:

Mouse 1x PS/2

Tastiera 1x PS/2

Slot 1x VGA

Slot 1x DVI

Slot 1x LAN

Slot 4x USB 2.0

Jack audio 3x

42


Specificazioni

Ingressi/ Uscite

Interni

Hi-Fi A85S2:

Connettore 8x SATA 6.0Gb/s

Distributore 2x USB 2.0


Connettore con 4 pin x1


Connettore Ventilatore processore x1

Connettore Ventilatore

Sistema x2

Distributore Pannello Frontale x1

Distributore Audio Frontale x1

Hi-Fi A75S2:








Sistema x2



Hi-Fi A55S2:







Sistema x2



Distributore CMOS Diretto x1


Distributore Slot Stampante x1

Distributore Consumabile

IR x1

Distributore Slot Serie x1

Connettore esterno

S/PDIF x1




IR x1


Connettore esterno

S/PDIF x1



IR x1


Connettore esterno

S/PDIF x1

Fattore di Forma Fattore di Forma ATX, 295 mm x 200 mm

Supporto SO


Biostar si riserva il diritto di aggiungere o ritirare il supporto per qualsiasi SO con o senza preavviso.

43


Japanese

仕様

CPU サポート

チップセット

メモリ

保存スペース

LAN

オーディオコーデ

ック

USB

拡張スロット

後部 I/O

AMD A-シリーズプロセッサの Socket FM2

最大 CPU TDP （Thermal Design Power 最大放熱量）:100 W

*CPU サポートリストについては、 www.biostar.com.tw

を参照してください。




デュアルチャンネル DDR3 800/ 1066/ 1333/ 1600/ 1866 をサポート

2 x DDR3 DIMM メモリスロット、最大 32 GB メモリまでサポート

各 DIMM は、非-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 モジュールをサポートしてい

ます

*サポートされているメモリのリストについては、 www.biostar.com.tw

を参照してく

ださい。

AMD A85/A75/A55 FCH

RAID 0,1,10, 5 & AHCI のサポート (A85 FCH)

RAID 0,1,10 & AHCI のサポート (A75/A55 FCH)

Realtek RTL 8111F

10/ 100/ 1000 Mb/s オートネゴーシエーション、半/全二重通信

ALC892

5.1 チャンネル, ハイデフィニションオーディオ, Biostar Hi-Fi

AMD A85/A75 FCH:

6x USB 2.0 ポート (後部 I/O に2つ及び内蔵ヘッダー経由に4つ)


AMD A55 FCH:


3x PCI スロット

2x PCIe 2.0 x1 スロット

1x PCIe 2.0 x16 スロット

Hi-Fi A85S2:

1x PS/2 キーボード

1x PS/2 マウス

1x HDMI ポート

1x VGA ポート

1x DVI ポート

1x LAN ポート

2x USB 2.0 ポート


3x オーディオジャック

Hi-Fi A75S2:


1x PS/2 マウス

1x HDMI ポート

1x VGA ポート

1x DVI ポート

1x LAN ポート




Hi-Fi A55S2:


1x PS/2 マウス

1x VGA ポート

1x DVI ポート

1x LAN ポート



44


仕様

内蔵 I/O

Hi-Fi A85S2:

8x SATA 6.0Gb/s コネクタ

2x USB 2.0 ヘッダー


1x 4-Pin パワーコネクタ


Hi-Fi A75S2:






Hi-Fi A55S2:





1x CPU ファンコネクタ


2x システムファンコネクタ

1x フロントパネルヘッダー

1x フロントオーディオヘッ

ダー

1x クリア CMOS ヘッダー





ダー


1x プリンターポートヘッダ

ー

1x コンシューマー IR ヘッダ

ー

1x シリアルポートヘッダー

1x S/PDIF アウトコネクタ


ー


ー






ダー



ー


ー



フォームファクタ ATX ファクタ、295 mm x 200 mm

サポート OS


Biostar には、通知なしでサポート OS を変更する権限があります。

45


Polish

Specyfikacje techniczne

Obsługa procesora

Rodzaj płyty

Gniazdo procesora (Socket) FM2 dla procesorów AMD seria-A

Moc Wydzielanego Ciepła (TDP - Thermal Design Power): 100Watt

* Proszę sprawdzić listę obsługiwanych procesorów na stronie internetowej www.biostar.com.tw




Pamięć

Obsługa pamięci DDR3 800/ 1066/ 1333/ 1600/ 1866 Dwukanałowa

2 x DDR3 DIMM Pamięć Gniazda procesora (Slot), Maksymalna wielkość pamięci 32

GB

Każdy DIMM obsługuje jeden moduł non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3

* Proszę sprawdzić listę obsługiwanych pamięć na stronie internetowej www.biostar.com.tw

Przechowywanie

LAN

Codec Audio

AMD A85/A75 FCH

Obsługa RAID 0,1,10, 5 & AHCI (A85 FCH)

Obsługa RAID 0,1,10 & AHCI (A75/A55 FCH)

Układ RTL 8111F

10/ 100/ 1000 Mb auto negocjacja, pojemność dupleks Połowe / Pełny

ALC892

Kanały Audio wysokiej Definicji 5.1, Biostar Hi-Fi

USB

Płyta AMD A85/A75 FCH:

6 x złącza USB 2.0 (2 przez tylne porty wejścia/ wyjścia oraz 4 przez wewnętrzne porty)


Płyta AMD A55 FCH:


Złącza rozszerzeń złącza 3x PCI (Slot) złącza 2x PCIe 2.0 x1 (Slot)

Tylne porty wejścia/ wyjścia złącza 1x PCIe 2.0 x16 (Slot)

Hi-Fi A85S2: Hi-Fi A75S2:

Myszka 1x PS/2

Klawiatura 1x PS/2

Port 1x HDMI (gniazdo)

Port 1x VGA

Myszka 1x PS/2

Klawiatura 1x PS/2

Port 1x HDMI (gniazdo)

Port 1x VGA

Port 1x DVI

Port 1x LAN

Porty 2x USB 2.0

Porty 2x USB 3.0

Porty audio 3x

Port 1x DVI

Port 1x LAN

Porty 2x USB 2.0

Porty 2x USB 3.0

Porty audio 3x

Hi-Fi A55S2:

Myszka 1x PS/2

Klawiatura 1x PS/2

Port 1x VGA

Port 1x DVI

Port 1x LAN

Porty 4x USB 2.0

Porty audio 3x

46

Wewnętrzne porty wejścia/ wyjścia

Obudowa

Obsługa OS


Specyfikacje techniczne

Hi-Fi A85S2:

Złącza 8x SATA 6.0Gb/s

Złącza 2x USB 2.0

Złącza 1x USB 3.0

Złącza 4 pionowe x 1


Hi-Fi A75S2:

Złącza 6x SATA 6.0Gb/s

Złącza 2x USB 2.0

Złącza 1x USB 3.0



Hi-Fi A55S2:

Złącza 6x SATA3.0Gb/s

Złącza 2x USB 2.0



Złącze wentylatora CPU x 1


Złącze wentylatora obudowy x

2

Złącze przedniego panelu x1

Złącze audio przedniego panelu x1

Złącze bezpośrednie CMOS x1

Złącze port drukarki x1

Złącze konsument IR x1

Port szeregowy x1

Port zewnętrzny S/PDIF x1



2




2







Port szeregowy x1




Port szeregowy x1


Obudowa ATX, 295 mm x 200 mm


Biostar zastrzega sobie prawo do dodania lub wycofania obsługi dla OS, z wypowiedzeniem lub bez wypowiedzenia.

47


Portuguese

Especificações

Suporte

Processador

Tipo Placa Mãe

Porta FM2 para processador AMD série-A

Alimentação de Design Térmico (TDP – Thermal Design Power): 100Watt

* Por favor consulte www.biostar.com.tw

para obter uma lista de suporte do processador.




Memória

Suporta DDR3 800/ 1066/ 1333/ 1600/ 1866 Canal Duplo

2 x DDR3 DIMM Slot de memória Suporta até 32 GB Memória

Cada DIMM suporta non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 módulo

* Por favor consulte www.biostar.com.tw

para obter uma lista de suporte do memória.

Armazenamento

AMD A85/A75/A55 FCH

Suporta RAID 0,1,10, 5 & AHCI (A85 FCH)

LAN

Codec de Audio

Suporta RAID 0,1,10 & AHCI (A75/A55 FCH)

Realtek RTL 8111F

10/ 100/ 1000 Mb auto negociação, capacidade duplex Metade / Cheio

ALC892

Canais de Áudio de Alta Definição 5.1, Biostar Hi-Fi

USB

Slots de expansão

Entradas/Saída s no painel traseiro

Plataforma AMD A85/A75 FCH:

Porta 6x USB 2.0 (2 nas entradas/saídas traseiras e 4 pelos Dispositivos internos)


Plataforma AMD A55 FCH:


Porta 3x PCI

Porta 2x PCIe 2.0 x1

Porta 1x PCIe 2.0 x16

Hi-Fi A85S2:

Mouse 1x PS/2

Teclado 1x PS/2

Porta 1x HDMI

Porta 1x VGA

Porta 1x DVI

Porta 1x LAN

Porta 2x USB 2.0

Porta 2x USB 3.0

Soquete audio 3x

Hi-Fi A75S2:

Mouse 1x PS/2

Teclado 1x PS/2

Porta 1x HDMI

Porta 1x VGA

Porta 1x DVI

Porta 1x LAN

Porta 2x USB 2.0

Porta 2x USB 3.0

Soquete audio 3x

Hi-Fi A55S2:

Mouse 1x PS/2

Teclado 1x PS/2

Porta 1x VGA

Porta 1x DVI

Porta 1x LAN

Porta 4x USB 2.0

Soquete audio 3x

48


Especificações

Conectores na placa

Hi-Fi A85S2:

Conector 8x SATA 6.0Gb/s

Dispositivo 2x USB 2.0


Hi-Fi A75S2:




Hi-Fi A55S2:



Conector de 4 pinos x1






Conector de Ventoinha processador x1


Conector de Ventoinha Sistema x2




Dispositivo Painel Frontal x1

Dispositivo de Audio Frontal x1





Dispositivo CMOS Direct x1


Dispositivo Porta Série x1

Conector Externo S/PDIF x1




Dispositivo Porta Impressora x1

Dispositivo Porta Impressora x1 Dispositivo Porta Impressora x1






Fator de Fôrma Fator de Fôrma ATX, 295 mm x 200 mm

Suporte OS


Biostar reserva seu direito de adicionar ou retirar o suporte para qualquer OS com ou sem notificação.

49


Russian

Поддержка центрального процессора

Набор микросхем

Память

Накопитель

Локальная сеть

Аудиокодек

USB

Гнезда расшир.

Задняя плата ввода-вывода

Спецификации

Сокет FM2 для процессоров AMD серии A

Максимальный термопакет центрального процессора (TDP): 100 ватт

* Перечень поддержки центрального процессора смотрите на www.biostar.com.tw

.




Поддерживает двухканальный DDR3 800/ 1066/ 1333/ 1600/ 1866

2 гнезда платы памяти DDR3 DIMM, максимальная память до 32 Гб

Каждый модуль DIMM поддерживает модуль не-ECC 512 Мб/ 1/ 2/ 4/ 8/ 16 Гб DDR3

* Перечень поддержки памяти смотрите на www.biostar.com.tw

.

AMD A85/A75/A55 FCH

Поддерживает RAID 0,1,10, 5 & AHCI (A85 FCH)

Поддерживает RAID 0,1,10 & AHCI (A75/A55 FCH)

Realtek RTL 8111F

Автосогласование 10/ 100/ 1000 Мб/с, работает в полно/полудуплексном режиме

ALC892

Каналы 5.1, высококачественное аудио, Biostar Hi-Fi

AMD A85/A75 FCH:

6 портов USB 2.0 (2 сзади ввода-вывода и 4 через внутренние контакты)


AMD A55 FCH:


3x гнезда PCI

2x PCIe 2.0 x1 гнездо

1x PCIe 2.0 x16 гнездо

Hi-Fi A85S2:

1 мышь PS/2

1 клавиатура PS/2

1 порт HDMI

1 порт VGA

1 порт DVI

1 порт локальной сети

2 порта USB 2.0


3 гнезд для подключения наушников

Hi-Fi A75S2:

1 мышь PS/2


1 порт HDMI

1 порт VGA

1 порт DVI





Hi-Fi A55S2:

1 мышь PS/2


1 порт VGA

1 порт DVI




50

Внутр. Плата ввода-вывода

Конструктив

Поддержка ОС


Спецификации

Hi-Fi A85S2:

Соединитель 8x SATA 6 Гб/с

2 контакта USB 2.0


1 4-выводный разъем питания


1 разъем вентилятора ЦП

2 разъема вентилятора системы

1 контакт передней панели

1 контакт передней аудиопанели

1 контакт микросхемы Clear

CMOS

1 контакт порта принтера

1 инфракрасный пользовательский контакт

1 контакт последовательного порта

1 соединитель S/PDIF-Out

Hi-Fi A75S2:




Hi-Fi A55S2:
















CMOS






CMOS





Форм-фактор ATX, 295 мм x 200 мм


Biostar оставляет за собой право добавлять или удалять поддержку любой ОС, с уведомлением или без.

51


Spanish

Especificaciones

Compatibilidad con el procesador

Tipo de Placa

Ranura FM2 para procesador AMD serie - A

Alimentación de Proyección Térmica (TDP – Thermal Design Power): 100Watt

*Por favor consultar con www.biostar.com.tw

para la lista de compatibilidad con el procesador.




Memoria

Soporta DDR3 800/ 1066/ 1333/ 1600/ 1866 Doble Canal

2x DDR3 DIMM Ranura de memoria Soporta hasta 32 GB Memoria

Cada DIMM soporta un modulo non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3

*Por favor consultar con www.biostar.com.tw

para la lista de compatibilidad con el memoria.

Almacenamiento de información

AMD A85/A75/A55 FCH

Soporta RAID 0,1,10, 5 & AHCI (A85 FCH)

Soporta RAID 0,1,10 & AHCI (A75/A55 FCH)

LAN

Códec Audio

Realtek RTL 8111F

10/ 100/ 1000 Mb/s auto negociación, capacidad dúplex Mitad/Completo

ALC892

Canales Audio de Alta Definición 5.1, Biostar Hi-Fi

USB

Ranuras de

Extinción

Plataforma AMD A85/A75 FCH:

Ranura 6x USB 2.0 (2 en las entradas/salidas posteriores y 4 por los distribuidores internos)


Plataforma AMD A55 FCH:


Ranura 3x PCI

Ranura 2x PCIe 2.0 x1

Ranura 1x PCIe 2.0 x16

Hi-Fi A85S2:

Ratón 1x PS/2

Teclado 1x PS/2

Ranura 1x HDMI

Ranura 1x VGA Panel trasero de

E/S Ranura 1x DVI

Ranura 1x LAN

Ranura 2x USB 2.0

Ranura 2x USB 3.0

Socket audio 3x

Hi-Fi A75S2:

Ratón 1x PS/2

Teclado 1x PS/2

Ranura 1x HDMI

Ranura 1x VGA

Ranura 1x DVI

Ranura 1x LAN

Ranura 2x USB 2.0

Ranura 2x USB 3.0

Socket audio 3x

Hi-Fi A55S2:

Ratón 1x PS/2

Teclado 1x PS/2

Ranura 1x VGA

Ranura 1x DVI

Ranura 1x LAN

Ranura 4x USB 2.0

Socket audio 3x

52


Especificaciones

Conectores en placa

Hi-Fi A85S2:

Conector 8x SATA 6Gb’s

Distribuidor 2x USB 2.0


Hi-Fi A75S2:




Hi-Fi A55S2:



Conector con 4 patillas x1






Conector Ventilador procesador x1


Conector Ventilador Sistema x2

Distribuidor Panel Frontal x1

Distribuidor Audio Frontal x1








Distribuidor CMOS Directo x1


Distribuidor Ranura Impresora x1

Distribuidor Consumible IR x1






Distribuidor Ranura Serie x1

Distribuidor Ranura Serie x1 Distribuidor Ranura Serie x1 Conector Externo S/PDIF x1

Conector Externo S/PDIF x1 Conector Externo S/PDIF x1

Factor de Forma Factor de Forma ATX, 295 mm x 200 mm

Soporte OS


Biostar reserva su derecho de añadir o retirar el soporte para cada OS con o sin notificación.

2012/12/12

53

Biostar Hi-Fi A55S2 Owner's Manual

FCC Information and Copyright

CHAPTER 1: INTRODUCTION

1.1 Before You Start

1.4 Rear Panel Connectors

Hi-Fi A85S2 / Hi-Fi A75S2

Hi-Fi A55S2

CHAPTER 2: HARDWARE INSTALLATION

2.1 Install Central Processing Unit (CPU)

CPU_FAN1: CPU Fan Header

SYS_FAN1/SYS_FAN2: System Fan Header

A. DDR3 Modules

B. Memory Capacity

C. Dual Channel Memory Installation

PEX16_1: PCI-Express Gen2 x16 Slot

PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slot

PCI1/ PCI2/ PCI3: Peripheral Component Interconnect Slot

Install an Expansion Card

JCMOS1: Clear CMOS Header

2.7 Headers & Connectors

ATXPWR1: ATX Power Source Connector

ATXPWR2: ATX Power Source Connector

PANEL1: Front Panel Header

SATA1~SATA8: Serial ATA Connectors

JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

F_AUDIO1: Front Panel Audio Header

JSPDIFOUT1: Digital Audio-out Connectors

J_COM1: Serial Port Connector

J_PRINT1: Printer Port Connector

CIR1: Consumer IR Connector

CHAPTER 3: UEFI BIOS & SOFTWARE

3.1 UEFI BIOS Setup

1. BIOS Update Utility

2. Online Update Utility

3. BIOSTAR BIOS Flasher

3.3 Software

Installing Software

Launching Software

eHot-Line (Optional)

Smart EAR

CHAPTER 4: USEFUL HELP

A. Driver Installation

B. Software Installation

C. Manual

4.2 AMI BIOS Beep Code

Boot Block Beep Codes

POST BIOS Beep Codes

4.3 Troubleshooting

CPU Overheated

Operating System

Raid Arrays

RAID Definitions

RAID 0:

RAID 1:

RAID 10:

RAID 5:

4.5 AMD Dual Graphics Technology

AMD Dual Graphics Technology Introduction

AMD Dual Graphics Requirement

AMD Dual Graphics Setup

APPENDIX: Specifications In Other Languages

Arabic

French

German

Italian

Japanese

Polish

Portuguese

Russian

Spanish

Related manuals

Biostar

Hi-Fi H61S3L

Biostar

Hi-Fi P61S2

Biostar

Hi-Fi A55S3

Biostar

Hi-Fi B85S2