Biostar MCP6PB M2+ Owner's Manual

MCP6PB M2+ Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction ........................................ 1
1.1
1.2
1.3
1.4
1.5
Before You Start ................................................................................ 1
Package Checklist ............................................................................. 1
Motherboard Features...................................................................... 2
Rear Panel Connectors ..................................................................... 3
Motherboard Layout......................................................................... 4
Chapter 2: Hardware Installation .......................... 5
2.1
2.2
2.3
2.4
Installing Central Processing Unit (CPU)....................................... 5
FAN Headers...................................................................................... 7
Installing System Memory ................................................................ 8
Connectors and Slots ....................................................................... 10
Chapter 3: Headers & Jumpers Setup .................. 12
3.1
3.2
How to Setup Jumpers .................................................................... 12
Detail Settings.................................................................................. 12
Chapter 4: RAID Functions .................................. 19
4.1
4.2
4.3
Operating System............................................................................ 19
Raid Arrays ...................................................................................... 19
How RAID Works............................................................................. 19
Chapter 5: Useful Help ........................................ 21
5.1
5.2
5.3
5.4
5.5
Driver Installation Note.................................................................. 21
Software............................................................................................ 22
Award BIOS Beep Code .................................................................. 23
Extra Information............................................................................ 23
Troubleshooting............................................................................... 24
Appendix: SPEC In Other Languages ................... 26
German.................................................................................................................. 26
French .................................................................................................................... 28
Italian..................................................................................................................... 30
Spanish ................................................................................................................... 32
Portuguese ............................................................................................................ 34
Polish...................................................................................................................... 36
Russian ................................................................................................................... 38
Arabic..................................................................................................................... 40
Japanese ................................................................................................................ 42
MCP6PB M2+
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„
„
„
„
„
„
1.2
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
PACKAGE CHECKLIST
IDE Cable X 1
Serial ATA Cable X 1
Rear I/O Panel for ATX Case X 1
Installation Guide X 1
Fully Setup Driver CD X 1 (full version manual files inside)
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
Serial ATA Power Cable X 1 (optional)
Note: The package contents may be differed by area or your motherboard version.
1
Motherboard Manual
1.3
MOTHERBOARD FEATURES
SPEC
Socket AM2 / AM2+
CPU
AMD Athlon 64 / Athlon 64 FX / Athlon 64 x2
/ Sempron / PhenomX3 / X4 processors
(Maximum Watt: 95W)
FSB
Chipset
Supports Hyper Transport and PowerNow
Supports up to 2 GT/s Bandwidth
GeForce 6150SE
Low Pin Count Interface
Provides the most commonly used legacy
Super I/O functionality
Environment Control initiatives
H/W Monitor
ITE's "Smart Guardian" function
DDR2 DIMM Slots x 2
Dual Channel Mode DDR2 memory module
Main
Max Memory Capacity 4GB
Supports DDR2 533 / 667 / 800
Memory
Each DIMM supports 256MB/512MB/
Supports DDR2 1066 (by AM2+ CPU)
1GB/2GB DDR2
Registered DIMM and ECC DIMM is not supported
Graphics
Integrated in GeForce 6150SE Chipset
Max Shared Video Memory is 256MB
IDE
Integrated IDE Controller
SATA II
Integrated Serial ATA Controller
LAN
Realtek RTL 8201CL PHY
Sound
ALC662
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4,
Data transfer rates up to 3 Gb/s
SATA Version 2.0 specification compliant
10 / 100 Mb/s auto negotiation
Half / Full duplex capability
5.1 channels audio out
High Definition Audio
PCI Express x16 slot
x1
Supports PCI-E x16 expansion cards
PCI slot
x1
Supports PCI expansion cards
On Board
Floppy connector
x1
Each connector supports 2 Floppy drives
Connector
IDE Connector
x1
Each connector supports 2 IDE device
SATA Connector
x2
Each connector supports 1 SATA devices
Front Panel Connector
x1
Supports front panel facilities
Front Audio Connector
x1
Supports front panel audio function
Slots
2
computing
Support HyperTransport 1.0 Ghz
ITE 8718F
Super I/O
AMD 64 Architecture enables 32 and 64 bit
MCP6PB M2+
SPEC
CPU Fan header
x1
CPU Fan power supply (with Smart Fan function)
System Fan header
x1
System Fan Power supply
CMOS clear header
x1
Restore CMOS data to factory default
USB connector
x2
Each connector supports 2 front panel USB ports
Power Connector (24pin)
x1
Connects to Power supply
Power Connector (4pin)
x1
Connects to Power supply
Printer Port Connector
x1
Each connector supports 1 Printer port
Serial port Connector
x1
Connects to RS-232 Port
PS/2 Keyboard
x1
Connects to PS/2 Keyboard
PS/2 Mouse
x1
Connects to PS/2 Mouse
Back Panel VGA port
x1
Connect to D-SUB monitor
I/O
LAN port
x1
Connect to RJ-45 ethernet cable
USB Port
x4
Connect to USB devices
Audio Jack
x3
Provide Audio-In/Out and microphone connection
Board Size
Special
Features
170 mm(W) x 235 mm(L)
MicroATX
RAID 0 / 1
Biostar Reserves the right to add or remove support
OS Support Windows XP / Vista / 7
1.4
for any OS With or without notice.
REAR PANEL CONNECTORS
PS/2
Mouse
LAN
Line In/
Sur round
Line Out
Mic I n 1/
Bass/ Cent er
PS/ 2
Keyboard
VGA
USBX2
USBX2
3
Motherboard Manual
1.5
MOTHERBOARD LAYOUT
JKBMS
J KB_PWR
J ATXPWR2
S ock et
D IM M B1
D IM M A1
A M 2+
JVG A
JUSB1
J ATXPWR1
JCFAN
ID E
JUSBPWR1
JUSBLAN1
GeForce
6150SE
JAUDIO1
BAT1
JU S B3
J USBPWR2
JCOM
JUSB2
JCMOS1
PEX16_1
LAN
BIOS
Super I/O
JPRNT
FDD
JAUDIOF
Codec
PCI1
SATA2
JSFAN
Note: ■ represents the 1st pin.
4
SATA1
J PANEL1
MCP6PB M2+
CHAPTER 2: HARDWARE INSTALLATION
2.1
INSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Remove the socket protection cap.
Step 2: Pull the lever toward direction A from the socket and then raise the
lever up to a 90-degree angle.
Step 3: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.
5
Motherboard Manual
Step 4: Hold the CPU down firmly, and then close the lever toward direct
B to complete the installation.
Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU
FAN power cable to the JCFAN. This completes the installation.
Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU
transition, you may encounter the situation that the new system failed to boot while using new
AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and
update the latest BIOS from our website for AM2+ CPUs support.
6
MCP6PB M2+
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN: CPU Fan Header
Pin
1
2
3
1
4
4
Assignment
Ground
+12V
FAN RPM rate
sense
Smart Fan
Control (By Fan)
JSFAN: System Fan Header
Pin
1
2
3
1
Assignment
Ground
+12V
FAN RPM rate
sense
3
Note:
The JCFAN supports 4-pin head connector; the JSFAN, 3-pin head connector. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be connected to pin#2, and the black wire is Ground and should be connected to
GND.
7
Motherboard Manual
2.3
INSTALLING SYSTEM MEMORY
D IM M A 1
D IM M B 1
A. Memory Modules
8
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot so that the notch on the DIMM matches the break
on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
MCP6PB M2+
B. Memory Capacity
DIMM Socket
Location
DDR2 Module
DIMMA1
256MB/512MB/1GB/2GB
DIMMB1
256MB/512MB/1GB/2GB
Total Memory
Size
Max is 4GB.
C. Dual Channel Memory installation
To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:
Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status
DIMMA1
DIMMB1
Disabled
O
X
Disabled
X
O
Enabled
O
O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
9
Motherboard Manual
2.4
CONNECTORS AND SLOTS
FDD: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cable.
2
34
1
33
IDE: IDE/ATAPI Connector
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two drives.
10
40
39
2
1
MCP6PB M2+
PEX16_1: PCI-Express Gen2 x16 Slot
-
PCI-Express 1.0a compliant.
Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
2X bandwidth over the traditional PCI architecture.
PEX16_1
PCI1: Peripheral Component Interconnect Slot
This motherboard is equipped with 1 standard PCI slot. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
11
Motherboard Manual
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1
HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DETAIL SETTINGS
JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep,
and speaker connection. It allows user to connect the PC case’s front panel
switch functions.
PWR_LED
On/Off
9
1
++ + SPK
Pin
1
2
3
4
5
6
7
8
12
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
16
8
RST
HLED
Assignment
N/A
N/A
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
N/A
N/A
Power LED
Power-on button
MCP6PB M2+
JATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
Pin
1
2
3
4
5
6
7
8
9
10
11
12
12
24
1
13
Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
JATXPWR2: ATX Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.
4
3
1
2
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
Note:
Before power on the system, please make sure that both JATXPWR1 and JATXPWR2
connectors have been plugged-in.
13
Motherboard Manual
JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel
These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
Pin
1
2
3
4
5
6
7
8
9
10
JU SB2 JU SB3
10
9
2
1
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
NC
Key
SATA1/SATA2: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 2 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
SATA2 SATA1
1
14
4
7
Pin
1
2
3
4
5
6
7
Assignment
Ground
TX+
TXGround
RXRX+
Ground
MCP6PB M2+
JAUDIOF: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.
2
10
1
9
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
JCOM: Serial port Connector
The motherboard has a Serial Port Connector for connecting RS-232 Port.
2
10
1
9
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
Carrier detect
Received data
Transmitted data
Data terminal ready
Signal ground
Data set ready
Request to send
Clear to send
Ring indicator
NC
15
Motherboard Manual
JCMOS1: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.
3
1
Pin 1-2 Close:
Normal Operation (default).
3
3
1
1
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
16
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Reset your desired password or clear the CMOS data.
MCP6PB M2+
JPRNT: Printer Port Connector
This header allows you to connect printer port on the PC.
2
1
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
25
Pin
14
15
16
17
18
19
20
21
22
23
24
25
26
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
17
Motherboard Manual
JUSBPWR1/JUSBPWR2: Power Source Headers for USB Ports
Pin 1-2 Close:
JUSBPWR1: +5V for USB ports at JUSB1/JUSBLAN1.
JUSBPWR2: +5V for USB ports at front panel (JUSB2/JUSB3).
Pin 2-3 Close:
JUSBPWR1: +5V STB for USB ports at JUSB1/JUSBLAN1.
JUSBPWR2: +5V STB for USB ports at front panel (JUSB2/JUSB3).
1
3
JUSBPWR1
1
Pin 1-2 close
3
3
1
1
JUSBPWR2
3
Pin 2-3 close
JKB_PWR: Power Source Header for PS/2 Keyboard and Mouse
1
1
3
3
Pin 1-2 close
+5V for PS/2 keyboard and
mouse.
1
3
Pin 2-3 close
+5V STB for PS/2 keyboard
and mouse.
18
MCP6PB M2+
CHAPTER 4: RAID FUNCTIONS
4.1
OPERATING SYSTEM
Supports Windows XP and Windows Vista.
4.2
RAID ARRAYS
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for
many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
4.3
HOW RAID WORKS
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large file into smaller blocks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.
Features and Benefits
­
­
­
­
­
Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the
platform.
Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
Benefits: provides increased data throughput, especially for large files. No
capacity loss penalty for parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
Fault Tolerance: No.
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
19
Motherboard Manual
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliable
media.
Features and Benefits
­
­
­
­
­
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
Fault Tolerance: Yes.
Block 1
Block 2
Block 3
20
Block 1
Block 2
Block 3
MCP6PB M2+
CHAPTER 5: USEFUL HELP
5.1
DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
21
Motherboard Manual
5.2
SOFTWARE
Installing Software
1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software
title.
3. Follow the on-screen instructions to complete the installation.
BIOScreen Utility
This utility allows you to personalize your boot logo easily. You can choose
JPG or BMP as your boot logo so as to customize your computer.
Please follow the following instructions to update boo logo:
1. Load Image：Choose the picture as the boot logo.
2. Transform：Transform the picture for BIOS and preview the result.
3.
22
Update Bios：Write the picture to BIOS Memory to complete the update.
MCP6PB M2+
5.3
AWARD BIOS BEEP CODE
Beep Sound
Meaning
One long beep followed by two short
beeps
Video card not found or video card
memory bad
High-low siren sound
CPU overheated
System will shut down automatically
One Short beep when system boot-up
Long beeps every other second
No error found during POST
No DRAM detected or install
5.4
EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
23
Motherboard Manual
5.5
TROUBLESHOOTING
Probable
1.
There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work
2.
Indicator light on keyboard does
not shine.
System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.
System does not boot from a hard disk
drive, but can be booted from optical
drive.
Solution
1.
2.
3.
Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
1.
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from an optical
1.
Back up data and applications
drive. Hard disks can be read,
files.
applications can be used, but system 2.
Reformat the hard drive.
fails to boot from a hard disk.
Re-install applications and data
using backup disks.
Screen message shows “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
System cannot boot after user installs a 1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
24
MCP6PB M2+
This page is intentionally left blank.
25
Motherboard Manual
APPENDIX: SPEC IN OTHER LANGUAGES
GERMAN
Spezifikationen
Sockel AM2 / AM2+
Die AMD 64-Architektur unterstützt eine 32-Bit- und
AMD Athlon 64 / Athlon 64 FX / Althlon 64
CPU
64-Bit-Datenverarbeitung
X2 / Sempron / PhenomX3 / X4
Unterstützt Hyper Transport und PowerNow
Prozessoren (Maximales Watt: 95W)
Unterstützt HyperTransport 2.0 Ghz mit
FSB
einer
Bandbreite von bis zu 4 GT/s
Chipsatz
GeForce 6150SE
Low Pin Count-Schnittstelle
ITE8716F
Umgebungskontrolle,
Super E/A
Bietet die häufig verwendeten alten Super
Hardware-Überwachung
E/A-Funktionen.
"Smart Guardian"-Funktion von ITE
Dual-Kanal DDR2 Speichermodul
DDR2 DIMM-Steckplätze x 2
Unterstützt DDR2 533 / 667 / 800
Arbeitsspeich Max. 4GB Arbeitsspeicher
Unterstützt DDR2 1066 (by AM2+ CPU)
er
Jeder DIMM unterstützt 256MB/512MB/
registrierte DIMMs. ECC DIMMs werden nicht
1GB/2GB DDR2.
unterstützt.
Grafik
Integrierter GeForce 6150SE-Chipsatz
IDE
Integrierter IDE-Controller
Max. 256 MB gemeinsam benutzter Videospeicher
Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus
Unterstützt PIO-Modus 0~4,
Datentransferrate bis zu 3 Gb/s
SATA
Integrierter Serial ATA-Controller
Konform mit der SATA-Spezifikation Version 2.0.
10 / 100 Mb/s Auto-Negotiation
LAN
Realtek RTL 8201CL PHY
Halb-/ Vollduplex-Funktion
HD
5.1-Kanal-Audioausgabe
Audio-Unters ALC662
Unterstützt High-Definition Audio
tützung
26
MCP6PB M2+
Spezifikationen
Steckplätze
PCI Express x16 Steckplatz
x1
PCI-Steckplatz
x1
Diskettenlaufwerkanschluss
x1
Jeder Anschluss unterstützt 2 Diskettenlaufwerke
IDE-Anschluss
x1
Jeder Anschluss unterstützt 2 IDE-Laufwerke
SATA-Anschluss
x2
Jeder Anschluss unterstützt 1 SATA-Laufwerk
Fronttafelanschluss
x1
Unterstützt die Fronttafelfunktionen
Front-Audioanschluss
x1
Unterstützt die Fronttafel-Audioanschlussfunktion
CPU-Lüfter-Sockel
x1
System-Lüfter-Sockel
x1
"CMOS löschen"-Sockel
x1
USB-Anschluss
x2
Onboard-Ans
chluss
CPU-Lüfterstromversorgungsanschluss (mit Smart
Fan-Funktion)
System-Lüfter-Stromversorgungsanschluss
Jeder Anschluss unterstützt 2
Fronttafel-USB-Anschlüsse
Stromanschluss (24-polig)
x1
Stromanschluss (4-polig)
x1
Druckeranschluss Anschluss
x1
Serieller Anschluss
x1
PS/2-Tastatur
x1
PS/2-Maus
x1
Rückseiten-E VGA-Anschluss
x1
/A
LAN-Anschluss
x1
USB-Anschluss
x4
Audioanschluss
x3
Platinengröß
Jeder Anschluss unterstützt 1 Druckeranschluss
170 mm (B) X 235 mm (L)
e
Sonderfunkti
onen
OS-Unterstü
tzung
Unterstützt RAID 0 / 1
Biostar behält sich das Recht vor, ohne Ankündigung
Windows XP / Vista / 7
die Unterstützung für ein Betriebssystem
hinzuzufügen oder zu entfernen.
27
Motherboard Manual
FRENCH
SPEC
Socket AM2 / AM2+
UC
Processeurs AMD Athlon 64 / Athlon 64 FX L'architecture AMD 64 permet le calcul 32 et 64 bits
/ Althlon 64 X2 / Sempron / PhenomX3 / Prend en charge Hyper Transport et PowerNow
X4 (Watt maximum : 95W)
Bus frontal
Chipset
Prend en charge Hyper Transport 2.0 Ghz
jusqu'à une bande passante de 4 GT/s
GeForce 6150SE
Interface à faible compte de broches
ITE 8718F
Super E/S
Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.
Module de mémoire DDR2 à mode à double voie
Mémoire
Capacité mémoire maximale de 4 Go
principale
Chaque DIMM prend en charge des DDR2
de 256Mo/512Mo/1Go/2Go
SATA
Contrôleur Serial ATA intégré
LAN
Realtek RTL 8201CL PHY
Connecteur
embarqué
28
Mémoire vidéo partagée maximale de 512 Mo
Taux de transfert jusqu'à 3 Go/s.
Conforme à la spécification SATA Version 2.0
10 / 100 Mb/s négociation automatique
Half / Full duplex capability
Sortie audio à 5.1 voies
ALC662
Prise en charge de l'audio haute définition
Fente PCI Express x16
x1
Fente PCI
x1
Connecteur de disquette
x1
Connecteur IDE
x1
Connecteur SATA
Les DIMM à registres et DIMM avec code correcteurs
Prend en charge le mode PIO 0~4,
audio HD
Fentes
Prend en charge la DDR2 1066 (by AM2+ CPU)
Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133
Prise en
charge
Prend en charge la DDR2 533 / 667 / 800
d'erreurs ne sont pas prises en charge
Graphiques Integré dans la chipset GeForce 6150SE
Contrôleur IDE intégré
Moniteur de matériel
Fonction "Gardien intelligent" de l'ITE
Fentes DDR2 DIMM x 2
IDE
Initiatives de contrôle environnementales,
x2
Chaque connector prend en charge 2 lecteurs de
disquettes
Chaque connecteur prend en charge 2 périphériques
IDE
Chaque connecteur prend en charge 1 périphérique
SATA
MCP6PB M2+
SPEC
Connecteur du panneau avant
x1
Connecteur Audio du panneau avant x1
Embase de ventilateur UC
x1
Embase de ventilateur système
x1
Embase d'effacement CMOS
x1
Connecteur USB
x2
Connecteur d'alimentation
x1
Prend en charge les équipements du panneau avant
Prend en charge la fonction audio du panneau avant
Alimentation électrique du ventilateur UC (avec
fonction de ventilateur intelligent)
Alimentation électrique du ventilateur système
Chaque connecteur prend en charge 2 ports USB de
panneau avant
(24 broches)
Connecteur d'alimentation
x1
(4 broches)
E/S du
panneau
arrière
Connecteur de Port d'imprimante
x1
Connecteur de Port série
x1
Clavier PS/2
x1
Souris PS/2
x1
Port VGA
x1
Port LAN
x1
Port USB
x4
Fiche audio
x3
Chaque connector prend en charge 1 Port
d'imprimante
Dimension
s de la
170 mm (l) X 235 mm (H)
carte
Fonctionnal
ités
Prise en charge RAID 0 / 1
spéciales
Support SE Windows XP / Vista / 7
Biostar se réserve le droit d'ajouter ou de supprimer le
support de SE avec ou sans préavis.
29
Motherboard Manual
ITALIAN
SPECIFICA
Socket AM2 / AM2+
CPU
Processori AMD Athlon 64 / Athlon 64 FX
/ Althlon 64 X2 / Sempron / PhenomX3 /
X4 (Watt massimo: 95W)
FSB
Chipset
L’architettura AMD 64 abilita la co mputazione 32
e 64 bit
Supporto di Hyper Transport e PowerNow
Supporto di HyperTransport 2.0 Ghz
fino a 4 GT/s di larghezza di banda
GeForce 6150SE
Interfaccia LPC (Low Pin Count)
ITE 8718F
Super I/O Fornisce le funzionalità legacy Super
I/O usate più comunemente.
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 2
Modulo di memoria DDR2 a canale doppio
Memoria
Capacità massima della memoria 4GB
Supporto di DDR2 533 / 667 / 800
principale
Ciascun DIMM supporta DDR2
Supporto di DDR2 1066 (by AM2+ CPU)
256MB/512MB/1GB/2GB
DIMM registrati e DIMM ECC non sono supportati
Grafica
Integrata nel Chipset GeForce 6150SE La memoria video condivisa massima è di 256 MB
Modalità Bus Master Ultra DMA 33 / 66 / 100 /
IDE
Controller IDE integrato
133
Supporto modalità PIO Mode 0-4
SATA
Controller Serial ATA integrato
LAN
Realtek RTL 8201CL PHY
Supporto
audio HD
Alloggi
Velocità di trasferimento dei dati fino a 3 Gb/s.
Compatibile specifiche SATA Versione 2.0.
Negoziazione automatica 10 / 100 Mb/s
Capacità Half / Full Duplex
Uscita audio 5.1 canali
ALC662
Supporto audio High-Definit ion (HD)
Alloggio PCI Express x16
x1
Alloggio PCI
x1
Connettori Connettore floppy
x1
Ciascun connettore supporta 2 unità Floppy
su scheda Connettore IDE
x1
Ciascun connettore supporta 2 unità IDE
Connettore SATA
x2
Ciascun connettore supporta 1 unità SATA
Connettore pannello frontale
x1
Supporta i servizi del pannello frontale
30
MCP6PB M2+
SPECIFICA
Connettore audio frontale
x1
Collettore ventolina CPU
x1
Collettore ventolina sistema
x1
Collettore cancellaz ione CMOS
x1
Connettore USB
x2
Connettore alimentazione
x1
Supporta la funzione audio pannello frontale
Alimentazione ventolina CPU (con funzione Smart
Fan)
Alimentazione ventolina di sistema
Ciascun connettore supporta 2 porte USB
pannello frontale
(24 pin)
Connettore alimentazione
x1
(4 pin)
I/O
pannello
posteriore
Dimension
i scheda
Connettore Porta stampante
x1
Connettore Porta seriale
x1
Tastiera PS/2
x1
Mouse PS/2
x1
Porta VGA
x1
Porta LAN
x1
Porta USB
x4
Connettore audio
x3
Ciascun connettore supporta 1 Porta stampante
170 mm (larghezza) x 235 mm
(altezza)
Caratterist
iche
Supporto RAID 0 / 1
speciali
Sistemi
operativi
supportati
Biostar si riserva il diritto di aggiungere o
Windows XP / Vista / 7
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
31
Motherboard Manual
SPANISH
Especificación
Conector AM2 / AM2+
Procesadores AMD Athlon 64 / Athlon 64 La arquitectura AMD 64 permite el procesado de 32 y
CPU
FX / Athlon 64 X2 / Sempron / PhenomX3 64 bits
/ X4
Soporta las tecnologías Hyper Transport y PowerNow
(Vatio máximo: 95W)
FSB
Conjunto
de chips
Admite HyperTransport 2.0 Ghz con un
ancho de banda de hasta 4 GT/s
GeForce 6150SE
Interfaz de cuenta Low Pin
ITE 8718F
Súper E/S
Le ofrece las funcionalidades heredadas
de uso más común Súper E/S.
Módulo de memoria DDR2 de canal Doble
Memoria
Capacidad máxima de memoria de 4GB
principal
Cada DIMM admite DDR de 256MB/
Controlador ATA Serie Integrado
Red Local
Realtek RTL 8201CL PHY
Soporte de
sonido HD
Ranuras
Memoria máxima de vídeo compartida de 256 MB
GeForce 6150SE
SATA
Admite DDR2 de 1066 (by AM2+ CPU)
ECC
Integrados en el conjunto de chips
Controlador IDE integrado
Admite DDR2 de 533 / 667 / 800
No admite DIMM registrados o DIMM compatibles con
512MB/1GB/2GB
IDE
Monitor hardware
Función "Guardia inteligente" de ITE
Ranuras DIMM DDR2 x 2
Gráficos
Iniciativas de control de entorno,
Modo bus maestro Ultra DMA 33 / 66 / 100 / 133
Soporte los Modos PIO 0~4,
Tasas de transferencia de hasta 3 Gb/s.
Compatible con la versión SATA 2.0.
Negociación de 10 / 100 Mb/s
Funciones Half / Full dúplex
Salida de sonido de 5.1 canales
ALC662
Soporte de sonido Alta Definición
Ranura PCI Express x16
X1
Ranura PCI
X1
Conectores Conector disco flexible
X1
Cada conector soporta 2 unidades de disco flexible
en placa
X1
Cada conector soporta 2 dispositivos IDE
32
Conector IDE
MCP6PB M2+
Especificación
Conector SATA
X2
Cada conector soporta 1 dispositivos SATA
Conector de panel frontal
X1
Soporta instalaciones en el panel frontal
Conector de sonido frontal
X1
Soporta funciones de sonido en el panel frontal
Cabecera de ventilador de CPU
X1
Fuente de alimentación de ventilador de CPU (con
función Smart Fan)
Cabecera de ventilador de sistema X1
Cabecera de borrado de CMOS
X1
Conector USB
X2
Conector de alimentación
X1
Fuente de alimentación de ventilador de sistema
Cada conector soporta 2 puertos USB frontales
(24 patillas)
Conector de alimentación
X1
(4 patillas)
Panel
trasero de
E/S
Tamaño de
la placa
Funciones
especiales
Conector Puerto de impresora
X1
Conector Puerto serie
X1
Teclado PS/2
X1
Ratón PS/2
X1
Puerto VGA
X1
Puerto de red local
X1
Puerto USB
X4
Conector de sonido
X3
170 mm. (A) X 235 Mm. (H)
Admite RAID 0 / 1
Soporte de
sistema
operativo
Cada conector soporta 1 Puerto de impresora
Windows XP / Vista / 7
Biostar se reserva el derecho de añadir o retirar el
soporte de cualquier SO con o sin aviso previo.
33
Motherboard Manual
PORTUGUESE
ESPECIFICAÇÕES
Socket AM2 / AM2+
Processadores AMD Athlon 64 / Athlon 64 A arquitectura AMD 64 permite uma computação de
CPU
FX / Althlon 64 X2 / Sempron / PhenomX3 32 e 64 bits
/ X4
Suporta as tecnologias Hyper Transport e PowerNow
(Watt máximo: 95W)
Suporta a tecnologia HyperTransport 2.0
FSB
Ghz com uma largura de banda até 4
GT/s
Chipset
Especificaç
ão Super
I/O
Memória
principal
Placa
gráfica
GeForce 6150SE
ITE 8718F
Interface LPC (Low Pin Count).
Proporciona as funcionalidades mais
Iniciativas para controlo do ambiente
utilizadas em termos da especificação
Monitorização do hardware
Super I/O.
Função "Smart Guardian" da ITE
Ranhuras DIMM DDR2 x 2
Módulo de memória DDR2 de canal duplo
Capacidade máxima de memória: 4 GB
Suporta módulos DDR2 533 / 667 / 800
Cada módulo DIMM suporta uma
Suporta módulos DDR2 1066 (by AM2+ CPU)
memória DDR2 de 256MB/512MB/
Os módulos DIMM registados e os DIMM ECC não são
1GB/2GB
suportados
Integrada no chipset GeForce 6150SE
Memória de vídeo máxima partilhada: 256 MB
IDE
Controlador IDE integrado
SATA
Controlador Serial ATA integrado
LAN
Realtek RTL 8201CL PHY
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,
Velocidades de transmissão de dados até 3 Gb/s.
Compatibilidade com a especificação SATA versão 2.0.
Auto negociação de 10 / 100 Mb/s
Capacidade semi/full-duplex
Suporte
para áudio
de alta
Saída de áudio de 5.1 canais
ALC662
Suporta a especificação High-Definition Audio
definição
Ranhuras
Ranhura PCI Express x16
x1
Ranhura PCI
x1
Conectores Conector da unidade de disquetes
x1
Cada conector suporta 2 unidades de disquetes
na placa
x1
Cada conector suporta 2 dispositivos IDE
34
Conector IDE
MCP6PB M2+
ESPECIFICAÇÕES
Conector SATA
x2
Cada conector suporta 1 dispositivo SATA
Conector do painel frontal
x1
Para suporte de várias funções no painel frontal
Conector de áudio frontal
x1
Conector da ventoinha da CPU
x1
Conector da ventoinha do sistema x1
Conector para limpeza do CMOS
Suporta a função de áudio no painel frontal
Alimentação da ventoinha da CPU (com a função
Smart Fan)
Alimentação da ventoinha do sistema
x1
Conector USB
x2
Conector de alimentação
x1
Cada conector suporta 2 portas USB no painel frontal
(24 pinos)
Conector de alimentação
x1
(4 pinos)
Conector da para impressora
x1
Conector da Porta série
x1
Teclado PS/2
Entradas/S Rato PS/2
x1
x1
aídas no
Porta VGA
x1
painel
Porta LAN
x1
traseiro
Porta USB
x4
Tomada de áudio
x3
Tamanho
da placa
Cada conector suporta 1 Porta para impressora
170 mm (L) X 235 mm (A)
Característi
cas
Suporta as funções RAID 0 / 1
especiais
Sistemas
operativos
suportados
A Biostar reserva-se o direito de adicionar ou remover
Windows XP / Vista / 7
suporte para qualquer sistema operativo com ou sem
aviso prévio.
35
Motherboard Manual
POLISH
SPEC
Socket AM2 / AM2+
Procesor
AMD Athlon 64 / Athlon 64 FX / Althlon 64
X2 / Sempron / PhenomX3 / X4 Procesory
(Maksymalny Watt: 95W)
FSB
Chipset
Architektura AMD 64 umożliwia przetwarzanie 32 i 64
bitowe
Obsługa Hyper Transport oraz PowerNow
Obsługa HyperTransport 2.0 Ghz o
szerokości pasma do 4 GT/s
GeForce 6150SE
Gniazda DDR2 DIMM x 2
Moduł pamięci DDR2 z trybem podwójnego kanału
Pamięć
Maks. wielkość pamięci 4GB
Obsługa DDR2 533 / 667 / 800
główna
Każde gniazdo DIMM obsługuje moduły
Obsługa DDR2 1066 (by AM2+ CPU)
256MB/512MB/1GB/2GB DDR2
Brak obsługi Registered DIMM oraz ECC DIMM
Interfejs Low Pin Count
ITE 8718F
Super I/O
Funkcje kontroli warunków pracy,
Zapewnia najbardziej powszechne
Monitor H/W
funkcje Super I/O.
Grafika
Zintegrowana w chipsecie GeForce
Maks. wielkość współdzielonej pamięci video wynosi
6150SE
256 MB
IDE
Zintegrowany kontroler IDE
SATA
Zintegrowany kontroler Serial ATA
LAN
Realtek RTL 8201CL PHY
Obsługa
audio HD
Funkcja ITE "Smart Guardian"
Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master
obsługa PIO tryb 0~4,
Transfer danych do 3 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2.0.
10 / 100 Mb/s z automatyczną negocjacją szybkości
Działanie w trybie połowicznego / pełnego dupleksu
5.1 kanałowe wyjście audio
ALC662
Obsługa High-Definition Audio
Gniazdo PCI Express x16
x1
Gniazdo PCI
x1
Złącza
Złącze napędu dyskietek
x1
Każde złącze obsługuje 2 napędy dyskietek
wbudowan
Złącze IDE
x1
Każde złącze obsługuje 2 urządzenia IDE
e
Złącze SATA
x2
Każde złącze obsługuje 1 urządzenie SATA
Złącze panela przedniego
x1
Obsługa elementów panela przedniego
Przednie złącze audio
x1
Obsługa funkcji audio na panelu przednim
Gniazda
36
MCP6PB M2+
SPEC
Złącze główkowe wentylatora procesora
Zasilanie wentylatora procesora (z funkcją Smart Fan)
x1
Złącze główkowe wentylatora
Zasilanie wentylatora systemowego
systemowego x1
Złącze główkowe kasowania CMOS x1
Złącze USB
x2
Każde złącze obsługuje 2 porty USB na panelu
przednim
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Złącze Port drukarki
x1
Złącze Port szeregowy
x1
Klawiatura PS/2
x1
Mysz PS/2
x1
Back Panel Port VGA
x1
I/O
Port LAN
x1
Port USB
x4
Gniazdo audio
x3
Wymiary
Każde złącze obsługuje 1 Port drukarki
170 mm (S) X 235 mm (W)
płyty
Funkcje
specjalne
Obsługa RAID 0 / 1
Obsluga
systemu
operacyjne
Biostar zastrzega sobie prawo dodawania lub
Windows XP / Vista / 7
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
go
37
Motherboard Manual
RUSSIAN
СПЕЦ
CPU
Гнездо AM2 / AM2+
(централь
Процессоры AMD Athlon 64 / Athlon 64
ный
FX / Althlon 64 X2 / Sempron / PhenomX3 на 32 и 64 бит
Поддержка Hyper Transport и PowerNow
процессор / X4
)
FSB
Набор
микросхем
(Максимальный ватт: 95W)
Поддержка HyperTransport 2.0 Ghz с
пропускной способностью до 4 GT/s
GeForce 6150SE
Модуль памяти с двухканальным режимом DDR2
Слоты DDR2 DIMM x 2
Основная
Максимальная ёмкость памяти 4 ГБ
память
Каждый модуль DIMM поддерживает
256МБ/512МБ/1ГБ/2ГБ DDR2
IDE
SATA
Локальная
сеть
Поддержка DDR2 1066 (by AM2+ CPU)
Не поддерживает зарегистрированные модули
Интерфейс с низким количеством выводов
Обеспечивает наиболее используемые
действующие функциональные
Инициативы по охране окружающей среды,
Аппаратный монитор
Функция ITE "Smart Guardian" (Интеллектуальная
возможности Super I/O.
Графика
Поддержка DDR2 533 / 667 / 800
DIMM and ECC DIMM
ITE 8718F
Super I/O
Архитектура AMD 64 разрешать обработка данных
защита)
Встроенная в набор микросхем GeForce Максимальная совместно используемая видео
6150SE
память составляет 256 МБ
Встроенное устройство управления
Режим "хозяина" шины Ultra DMA 33 / 66 / 100 / 133
встроенными интерфейсами устройств Поддержка режима PIO 0~4,
Встроенное последовательное
скорость передачи данных до 3 гигабит/с.
устройство управления ATA
Соответствие спецификации SATA версия 2.0.
Автоматическое согласование 10 / 100 Мб/с
Realtek RTL 8201CL PHY
Частичная / полная дуплексная способность
Звуковая
поддержка
жесткого
Звуковая поддержка High-Definition
ALC662
5.1канальный звуковой выход
диска
Слоты
Встроенны
й разъём
38
Слот PCI Express x16
x1
Слот PCI
x1
Разъём НГМД
x1
Разъём IDE
x1
Разъём SATA
x2
Каждый разъём поддерживает 2 накопителя на
гибких магнитных дисках
Каждый разъём поддерживает 2 встроенных
интерфейса накопителей
Каждый разъём поддерживает 1 устройство SATA
MCP6PB M2+
СПЕЦ
Разъём на лицевой панели
x1
Поддержка устройств на лицевой панели
Входной звуковой разъём
x1
Поддержка звуковых функций на лицевой панели
Контактирующее приспособление
Источник питания для вентилятора центрального
вентилятора центрального
процессора (с функцией интеллектуального
процессора
x1
Контактирующее приспособление
вентилятора системы
x1
вентилятора)
Источник питания для вентилятора системы
Открытое контактирующее
приспособление CMOS
x1
USB-разъём
x2
Разъем питания (24 вывод)
x1
Разъем питания (4 вывод)
x1
Разъём Порт подключения
Каждый разъём поддерживает 1 Порт подключения
принтера
x1
Разъём Последовательный порт
x1
Клавиатура PS/2
x1
Задняя
Мышь PS/2
x1
панель
Порт VGA
x1
средств
Порт LAN
x1
ввода-выв USB-порт
x4
ода
панели
принтера
Гнездо для подключения
наушников
Размер
Каждый разъём поддерживает 2 USB-порта на
лицевой панели
x3
170 мм (Ш) X 235 мм (В)
Специальн
ые
техническ
ие
Поддержка RAID 0 / 1
характери
стики
Поддержк
а OS
Biostar сохраняет за собой право добавлять или
Windows XP / Vista / 7
удалять средства обеспечения для OS с или без
предварительного уведомления.
39
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪AM2 / AM2+‬ﻡﻘﺒﺲ‬
‫وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫‪AMD Athlon 64 / Athlon 64 FX / Sempron /‬ﻡﻌﺎﻟﺠﺎت‬
‫إﺟﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺑﻴﺔ ﺑﺴﺮﻋﺔ ‪ 32‬و‪ 64‬ﺑﺖ‪AMD 64‬ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ‬
‫اﻟﻤﺮآﺰیﺔ‬
‫‪PhenomX3 / X4 / Althlon 64 X2‬‬
‫‪ PowerNow‬و ‪Hyper Transport 3‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫)و‪: 95‬ﻗﺼ ﻮى واط(‬
‫اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ اﻟﺠﺎﻥﺒﻲ ‪ 4 GT/s‬ﺑﺘﺮدد یﺼﻞ إﻟﻰ‪HyperTransport Ghz2.0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫‪GeForce 6150SE‬‬
‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪Super I/O‬‬
‫‪ITE 8718F‬‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻡًﺎ‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬
‫ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺡﺎﻟﺔ اﻷﺟﻬﺰة‬
‫‪ ITE‬ﻡﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫ﻓﺘﺤﺔ ‪DDR2 DIMM‬‬
‫ﻋﺪد‪2‬‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 4‬ﺟﻴﺠﺎ ﺑﺎیﺖ‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫ﻡﻴﺠﺎ ‪ 256/512‬ﺳﻌﺔ ‪ DDR2‬ﺗﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫ﺑﺎیﺖ و‪ /1‬و‪ 2‬ﺟﻴﺠﺎ ﺑﺎیﺖ‬
‫ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت‬
‫‪ GeForce 6150SE‬ﻡﺪﻡﺠﺔ ﻓﻲ رﻗﺎﺋﻖ‬
‫ﻡﻨﻔﺬ ‪IDE‬‬
‫ﻡﺘﻜﺎﻡﻞ‪IDE‬ﻡﺘﺤﻜﻢ‬
‫‪SATA‬‬
‫ﻡﺘﻜﺎﻡﻞ‪Serial ATA‬ﻡﺘﺤﻜﻢ‬
‫ﺵﺒﻜﺔ داﺥﻠﻴﺔ‬
‫‪Realtek RTL 8201CL PHY‬‬
‫دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ‬
‫ﻡﺰدوﺟﺔ اﻟﻘﻨﺎة‪DDR2‬وﺡﺪة ذاآﺮة‬
‫ﺳﻌﺎت ‪ 800 / 667 / 533‬ﻡﻴﺠﺎ ﺑﺎیﺖ‪DDR2‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع‬
‫ﺳﻌﺎت ‪ 1066‬ﻡﻴﺠﺎ ﺑﺎیﺖ‪DDR2‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮع‬
‫)‪(DDR2 1066 is by AM2+ CPU‬‬
‫‪ ECC‬وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻡﻊ ‪DIMM‬ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫یﺠﺎ ﺑﺎیﺖ‪256‬أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪیﻮ اﻟﻤﺸﺘﺮآﺔ‬
‫وﺿﻊ رﺋﻴﺴﻲ‪Ultra DMA 33 / 66 / 100 / 133‬ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ‬
‫‪PIO Mode 0~4‬دﻋﻢ وﺿﻊ‬
‫ﺟﻴﺠﺎﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‪3.‬ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ‬
‫‪ 2.0.‬اﻹﺹﺪار ‪SATA‬ﻡﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬
‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻡﻴﺠﺎ ﺑﺎیﺖ ‪ /‬ﺙﺎﻥﻴﺔ‬
‫إﻡﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻡﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‪5.1‬‬
‫‪ALC662‬‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻡﻦ‬
‫اﻟﺘﻌﺮیﻒ‬
‫ﻓﺘﺤﺔ ‪PCI Express x16‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد‪1‬‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫ﻡﻨﻔﺬ ﻡﺤﺮك أﻗﺮاص ﻡﺮﻥﺔ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ ﻡﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻥﺔ‬
‫اﻟﻠﻮﺡﺔ‬
‫ﻡﻨﻔﺬ ‪IDE‬‬
‫ﻋﺪد ‪1‬‬
‫‪IDE‬یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺟﻬﺰة‬
‫ﻡﻨﻔﺬ ‪SATA‬‬
‫ﻋﺪد‪2‬‬
‫‪SATA‬یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺡﺪ ﻡﻦ أﺟﻬﺰة‬
‫ﻡﻨﻔﺬ اﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‬
‫اﻟﻔﺘﺤﺎت‬
‫‪40‬‬
‫‪MCP6PB M2+‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‬
‫وﺹﻠﺔ ﻡﺮوﺡﺔ وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ‬
‫ﻋﺪد ‪1‬‬
‫‪Smart Fan‬ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺡﺔ وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔ‬
‫وﺹﻠﺔ ﻡﺮوﺡﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪1‬‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺡﺔ اﻟﻨﻈﺎم‬
‫وﺹﻠﺔ ﻡﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ‪USB‬‬
‫ﻋﺪد ‪2‬‬
‫ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺡﺔ ﻡﻔﺎﺗﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﺎﻓﺬ دﺥﻞ‪/‬ﺥﺮج‬
‫ﻡﻨﻔﺬ ‪VGA‬‬
‫ﻋﺪد ‪1‬‬
‫اﻟﻠﻮﺡﺔ اﻟﺨﻠﻔﻴﺔ‬
‫ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻡﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻡﻨﺎﻓﺬ ‪USB‬‬
‫ﻋﺪد‪4‬‬
‫ﻡﻘﺒﺲ ﺹﻮت‬
‫ﻋﺪ‪3‬‬
‫ﺡﺠﻢ اﻟﻠﻮﺡﺔ‬
‫‪ 170‬ﻡﻢ )ﻋﺮض( ‪ 235 X‬ﻡﻢ )ارﺗﻔﺎع(‬
‫ﻡﺰایﺎ ﺥﺎﺹﺔ‬
‫‪RAID 0 / 1‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫‪41‬‬
‫‪Windows XP / Vista / 7‬‬
‫ﺑﺎﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ‪USB‬یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲ‬
‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أو ‪Biostar‬ﺗﺤﺘﻔﻆ‬
‫ﺑﺪون إﺥﻄﺎر‪.‬‬
Motherboard Manual
JAPANESE
仕様
Socket AM2 / AM2+
CPU
AMD 64アーキテクチャでは、32ビットと64ビット計算が可
AMD Athlon 64 / Athlon 64 FX / Althlon 64 能です
X2 / Sempron / PhenomX3 / X4 プロセッ ハイパートランスポートとクールアンドクワイアットをサポ
サ (最高のワット: 95W)
FSB
チップセッ
ートします
4 GT/sのバンド幅までハイパートランスポー
ト2.0 GHzをサポートします
GeForce 6150SE
ト
DDR2 DIMMスロット x 2
デュアル チャンネルモードDDR2メモリモジュール
メインメモ
最大メモリ容量4GB
DDR2 533 / 667 / 800 をサポート
リ
各DIMMは 256MB/512MB/1GB/2GB
DDR2 1066 をサポート (by AM2+ CPU)
DDR2をサポート
登録済みDIMMとECC DIMMはサポートされません
低ピンカウントインターフェイス
ITE 8718F
Super I/O
もっとも一般に使用されるレガシーSuper I/O
機能を採用しています。
グラフィッ
環境コントロールイニシアチブ、
H/Wモニター
ITEの「スマートガーディアン」機能
GeForce 6150SEチップセットに統合
最大の共有ビデオメモリは256 Bです
クス
IDE
統合IDEコントローラ
SATA
統合シリアルATAコントローラ
LAN
Realtek RTL 8201CL PHY
Ultra DMA 33 / 66 / 100 / 133バスマスタモード
PIO Mode 0~4のサポート、
最高3Gb/秒のデータ転送速度
SATAバージョン2.0仕様に準拠。
10 / 100 Mb/秒のオートネゴシエーション
半/全二重機能
HDオーディ
オのサポー
5.1チャンネルオーディオアウト
ALC662
ハイデフィニションオーディオのサポート
ト
PCI Express x16スロット
x1
PCIスロット
x1
オンボード
フロッピーコネクタ
x1
各コネクタは2つのフロッピードライブをサポートします
コネクタ
IDEコネクタ
x1
各コネクタは2つのIDEデバイスをサポートします
SATAコネクタ
x2
各コネクタは1つのSATAデバイスをサポートします
スロット
42
MCP6PB M2+
仕様
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x1
システムファン電源装置
CMOSクリアヘッダ
x1
USBコネクタ
x2
電源コネクタ(24ピン)
x1
電源コネクタ(4ピン)
x1
プリンタポートコネクタ
x1
シリアルポートコネクタ
x1
PS/2キーボード
x1
PS/2マウス
x1
背面パネル
VGAポート
x1
I/O
LANポート
x1
USBポート
x4
オーディオジャック
x3
各コネクタは2つのフロントパネルUSBポートをサポートし
ます
ボードサイ
各コネクタは1つのプリンタポートをサポートします
170 mm (幅) X 235 mm (高さ)
ズ
特殊機能
RAID 0 / 1 のサポート
OSサポート Windows XP / Vista / 7
Biostarは事前のサポートなしにOSサポートを追加または削
除する権利を留保します。
2009/09/18
43