Biostar TA870U3+ Setup Manual

TA870U3+/TA870B Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.

Dichiarazione di conformità sintetica

Ai sensi dell’art. 2 comma 3 del D.M.

275 del 30/10/2002

Si dichiara che questo prodotto è conforme alle normative vigenti e soddisfa i requisiti essenziali richiesti dalle direttive

2004/108/CE, 2006/95/CE e

1999/05/CE quando ad esso applicabili

Short Declaration of conformity

We declare this product is complying with the laws in force and meeting all the essential requirements as specified by the directives

2004/108/CE, 2006/95/CE and

1999/05/CE whenever these laws may be applied

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1

1.2

1.3

1.4

Before You Start ................................................................................ 1

Package Checklist ............................................................................. 1

Motherboard Features...................................................................... 2

Rear Panel Connectors ..................................................................... 2

1.5

Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation .......................... 5

2.1

2.2

Installing Central Processing Unit (CPU)....................................... 5

FAN Headers...................................................................................... 7

2.3

Installing System Memory................................................................ 8

2.4

Connectors and Slots ....................................................................... 10

Chapter 3: Headers & Jumpers Setup .................. 13

3.1

3.2

How to Setup Jumpers .................................................................... 13

Detail Settings.................................................................................. 13

Chapter 4: RAID Functions .................................. 18

4.1

4.2

Operating System............................................................................ 18

Raid Arrays ...................................................................................... 18

4.3

How RAID Works............................................................................. 18

Chapter 5: T-Series BIOS & Software................... 22

5.1

5.2

T-Series BIOS..................................................................................... 22

T-Series Software ............................................................................. 30

Chapter 6: Useful Help ........................................ 40

6.1

6.2

6.3

6.4

Driver Installation Note.................................................................. 40

Extra Information............................................................................ 41

AMI BIOS Beep Code....................................................................... 42

AMI BIOS Post Code ........................................................................ 43

6.5

Troubleshooting............................................................................... 45

Appendix: SPEC In Other Languages ................... 46

German.................................................................................................................. 46

French .................................................................................................................... 48

Italian..................................................................................................................... 50

Spanish ................................................................................................................... 52

Portuguese ............................................................................................................ 54

Polish...................................................................................................................... 56

Russian ................................................................................................................... 58

Arabic..................................................................................................................... 60

Japanese ................................................................................................................ 62

TA870U3+/TA870B

CHAPTER 1: INTRODUCTION

1.1 B

EFORE

Y

OU

S

TART

Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:

Prepare a dry and stable working environment with sufficient lighting.

Always disconnect the computer from power outlet before operation.

Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.

Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board.

Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment.

Keep the computer from dangerous area, such as heat source, humid air and water.

The operating temperatures of the computer should be

0 to 45 degrees Celsius.

1.2 P

ACKAGE

C

HECKLIST

Serial ATA Cable X 3

Serial ATA Power Cable X 1

Rear I/O Panel for ATX Case X 1

User’s Manual X 1

Fully Setup Driver CD X 1

USB 2.0 Cable X1 (optional)

S/PDIF out Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

1

Motherboard Manual

1.3 M

OTHERBOARD

F

EATURES

CPU

FSB

Socket AM3

TA870U3+

AMD Phenom II/Athlon II/Sempron processors

AMD 64 Architecture enables 32 and 64 bit computing

TA870B

Socket AM3

AMD Phenom II/Athlon II/Sempron processors

AMD 64 Architecture enables 32 and 64 bit computing

Supports Hyper Transport 3.0 and Cool=n=Quiet Supports Hyper Transport 3.0 and Cool=n=Quiet

(Maximum Watt: 140W) (Maximum Watt: 140W)

Support HyperTransport 3.0 Support HyperTransport 3.0

Supports up to 5.2 GT/s Bandwidth

AMD 870

Supports up to 5.2 GT/s Bandwidth

AMD 870

Chipset

Super I/O

AMD SB850

ITE 8728

AMD SB850

ITE 8728

Provides the most commonly used legacy Super Provides the most commonly used legacy Super

I/O functionality

Low Pin Count Interface

I/O functionality

Low Pin Count Interface

Main

Memory

SATA 3

Environment Control initiatives

H/W Monitor

ITE's "Smart Guardian" function

DDR3 DIMM Slots x 4

Max Memory Capacity 16GB

Each DIMM supports 512MB/1GB/2GB/

4GB DDR3

Dual Channel Mode DDR3 memory module

Supports DDR3 800 / 1066 / 1333

Supports DDR3 1600 (OC)

Registered DIMM and ECC DIMM is not supported

Integrated Serial ATA Controller

Data transfer rates up to 6 Gb/s

SATA Version 3.0 specification compliant

Environment Control initiatives

H/W Monitor

ITE's "Smart Guardian" function

DDR3 DIMM Slots x 4

Max Memory Capacity 16GB

Each DIMM supports 512MB/1GB/2GB/

4GB DDR3

Dual Channel Mode DDR3 memory module

Supports DDR3 800 / 1066 / 1333

Supports DDR3 1600 (OC)

Registered DIMM and ECC DIMM is not supported

Integrated Serial ATA Controller

Data transfer rates up to 6 Gb/s

SATA Version 3.0 specification compliant

LAN

Sound

Slots

Realtek RTL 8111E

10 / 100 / 1000 Mb/s auto negotiation

Half / Full duplex capability

ALC662

5.1 channels audio out

High Definition Audio

PCI Express Gen2 x16 slot

PCI Express Gen2 x 1 slot

PCI slot x2 x2 x2

Realtek RTL 8111E

10 / 100 / 1000 Mb/s auto negotiation


ALC662

5.1 channels audio out

High Definition Audio

PCI Express Gen2 x16 slot

PCI Express Gen2 x 1 slot

PCI slot x2 x2 x2

2

TA870U3+

SATA Connector

Front Panel Connector

Front Audio Connector

S/PDIF Out Connector

CPU Fan Header

System Fan Header On Board

Connector

Back Panel

I/O

CMOS clear Header

USB 2.0 Connector

Power Connector (24pin)


Consumer IR Connector

Printer Port Connector

PS/2 Keyboard

PS/2 Mouse

Serial Port

LAN Port

USB 2.0 Port (by SB850)

USB 3.0 Port (by ASM1042)

Audio Jack

Board Size 220 mm(W) x 305 mm(L)

Special

Features

RAID 0 / 1 / 10 / 5 support

Windows XP / Vista / 7

OS Support Biostar reserves the right to add or remove support for any OS With or without notice. x1 x2 x1 x3 x6 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x2 x2 x3

1.4 R

EAR

P

ANEL

C

ONNECTORS

TA870U3+/TA870B

TA870B

SATA Connector

Front Panel Connector

Front Audio Connector

S/PDIF Out Connector

CPU Fan Header

System Fan Header

CMOS clear Header

USB 2.0 Connector



Consumer IR Connector

Printer Port Connector x1 x2 x1 x3 x6 x1 x1 x1 x1 x1 x1 x1

PS/2 Keyboard

PS/2 Mouse

Serial Port

LAN Port

USB 2.0 Port

Audio Jack x1 x1 x1 x1 x4 x3

220 mm(W) x 305 mm(L)

RAID 0 / 1 / 10 / 5 support


Biostar reserves the right to add or remove support for any OS With or without notice.

PS/2

Mouse

LAN

Line In/

Surround

C OM1 Line Out

Mic In 1/

Bass/ Center

PS/2

Keyboard

USB3.0X2

(TA870U3+)

USB2.0X2

(TA870B)

U SB2.0X2

NOTE: Since the audio chip supports High Definition Audio Specification, the function of each audio jack can be defined by software. The input / output function of each audio jack listed above represents the default setting. However, when connecting external microphone to the audio port, please use the Line In (blue) and Mic In (Pink) audio jack.

NOTE: USB3.0 ports are backward compatible with USB2.0/USB1.X devices. USB3.0 is controlled by Asmedia ASM1042, but, USB2.0/USB1.X is controlled by SB850.

3


1.5 M

OTHERBOARD

L

AYOUT

PH2_LED

PH1_LED

PH4_LED

PH3_LED NB_PH_LED

KBMS1

ATXPWR2

CPU_FAN1

4

ATXPWR1

USB3_0

USB2_0

(TA870U3+)

(TA870B)

RJ45USB1

AUDIO1

LED_D1

LAN

LED_D2

AMD

870

SYS_FAN1

PEX1_1

SATA6

SATA5

PEX16_1

Super

I/O

PEX1_2

PEX16_2

AMD

SB850

Codec PCI1

BAT1

JSPDIFOUT1

F_AUDIO1

J_PRINT1

PCI2

CI R1 SYS_FAN2 F_USB1 F_USB2 F_USB3 PANEL1

Note: represents the 1 st pin.

SW_PWR1

SW_RST1

BIOS

JCMOS1

SATA3

SATA1

SATA4

SATA2

TA870U3+/TA870B

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING

C

ENTRAL

P

ROCESSING

U

NIT

(CPU)

Step 1: Pull the lever toward direction A from the socket and then raise the lever up to a 90-degree angle.

Step 2: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only in the correct orientation.

5


Step 3: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the CPU_FAN1. This completes the installation.

6

TA870U3+/TA870B

2.2 FAN H

EADERS

These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to pin#1.

CPU_FAN1: CPU Fan Header

4 1

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

Fan

Control (By Fan)

SYS_FAN1: System Fan Header

SYS_FAN2: NorthBridge Fan Header

SYS_FAN1

1 3

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

SYS_FAN2

Note:

CPU_FAN1, SYS_FAN1/2 support 4-pin and 3-pin head connectors. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.

7


2.3 I

NSTALLING

S

YSTEM

M

EMORY

A. DDR3 Modules

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the break on the Slot.

8

2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.

TA870U3+/TA870B

B. Memory Capacity

DIMM Socket

Location

DDR3 Module

Total Memory

DDR3_A1 512MB/1GB/2GB/4GB

Size

DDR3_B1 512MB/1GB/2GB/4GB

DDR3_B2 512MB/1GB/2GB/4GB

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2

Enabled O X O X

Enabled X O X O

Enabled O O O O

(O: memory installed; X: memory not installed)

The DRAM bus width of the memory module must be the same (x8 or x16)

9


2.4 C

ONNECTORS AND

S

LOTS

SATA1~SATA6: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 6 channels SATA interface, it satisfies the SATA 3.0 spec and with transfer rate of 6.0Gb/s.

7

4

1

SATA5 SATA6

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

7 Ground

1 4 7

SATA3 SATA4

SATA1 SATA2

ATXPWR2: ATX Power Source Connector

This connector provides +12V to CPU power circuit.

4 3

1 2

Pin Assignment

1 +12V

2 +12V

3 Ground

4 Ground

10

TA870U3+/TA870B

ATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX power supply.

1 2 24

Pin Assignment

13 +3.3V

14 -12V

15 Ground

16 PS_ON

17 Ground

18 Ground

19 Ground

20 NC

21 +5V

22 +5V

23 +5V

24 Ground

1 1 3

Pin Assignment

1 +3.3V

2 +3.3V

3 Ground

4 +5V

5 Ground

6 +5V

7 Ground

8 PW_OK

10 +12V

11 +12V

12 +3.3V

Note:

Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors have been plugged-in.

PCI1/PCI2: Peripheral Component Interconnect Slots

PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

11


PEX16_1: PCI-Express Gen2 x16 Slot

-

-

-

PCI-Express 2.0 compliant.

Maximum theoretical realized bandwidth of 8GB/s simultaneously per direction, for an aggregate of 16GB/s totally.

PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

PEX16_2: PCI-Express Gen2 x4 Slot

-

-

-

PCI-Express 2.0 compliant.

Data transfer bandwidth up to 2GB/s per direction;4GB/s in total.

PCI-Express Gen2 supports a raw bit-rate of 2.5Gb/s on the data pins.

PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slot

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.

PEX1_1

PEX16_1

PEX1_2

PEX16_2

12

TA870U3+/TA870B

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO

S

ETUP

J

UMPERS

The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

3.2 D

ETAIL

S

ETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.

9

1

PWR_LED

On/Off

+ + -

+ -

16

8

SPK

HLED

RST

Pin Assignment Function Function

1 +5V

2 N/A

3 N/A

4 Speaker

Speaker

Connector

9 N/A

10 N/A

11 N/A

12 Power LED (+)

N/A

N/A

5

6

HDD LED (+)

HDD LED (-)

Hard drive

LED

13

14

Power LED (+)

Power LED (-)

Power LED

7 Ground

Reset button

16 Ground

Power-on button

13


JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard.

1 3

1 3

Pin 1-2 Close:

Normal Operation

(default).

1 3

Pin 2-3 Close:

Clear CMOS data.

※

Clear CMOS Procedures:

1.

2.

3.

4.

5.

6.

Remove AC power line.

Set the jumper to “Pin 2-3 close”.

Wait for five seconds.

Set the jumper to “Pin 1-2 close”.

Power on the AC.

Reset your desired password or clear the CMOS data.

CIR1: Consumer IR Connector

This header is for infrared remote control and communication.

Pin Assignment

1 IrDA serial input

2 Ground

3 Ground

4 Key

5 IrDA serial output

2 6

1 5

14

TA870U3+/TA870B

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable.

Pin

1

Assignment

Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

2

1

10

9

8 Key

9 Left line in

JSPDIFOUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Pin Assignment

1 +5V

2 SPDIF_OUT

3 Ground

1 3

15


J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

16

2 2 6

1 2 5

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF

16 Ground

4 -Error

18 Ground

6 -Init

8 -Scltin

10 Ground

12 Ground

19 -ACK

20 Ground

21 Busy

22 Ground

23 PE

24 Ground

25 SCLT

26 Key

F_USB1~F_USB3: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader.

Pin Assignment

F_USB1 F_

F_ USB2

USB3

2 1 0

1 9

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

10 NC

On-Board LED Indicators

There are 6 LED indicators showing system status.

TA870U3+/TA870B

LED_D1

LED_D2

LED_D1 & LED_D2: Debug Indicators

PH1_LED ~ PH4_LED/NB_PH_LED: Power Status Indicators

Please refer to the tables below for specific messages:

LED_D1 LED_D2 Message

OFF OFF

PH1_LED~PH4_LED

NB_PH_LED

Abnormal: CPU / Chipset error.

Phase Indicator

On-Board Buttons

There are 2 on-board buttons.

SW_RST1: Reset button.

SW_PWR1: Power Switch button.

SW_RST1

SW_PWT1

17


CHAPTER 4: RAID FUNCTIONS

4.1 O

PERATING

S

YSTEM

Supports Windows XP, Windows Vista, and Windows 7.

4.2 R

AID

A

RRAYS

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.

RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity.

4.3 H

OW

RAID W

ORKS

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the platform.

Uses: Intended for non-critical data requiring high data throughput, or any environment that does not require fault tolerance.

Benefits: provides increased data throughput, especially for large files. No capacity loss penalty for parity.

Drawbacks: Does not deliver any fault tolerance. If any drive in the array fails, all data is lost.

Fault Tolerance: No.

18

Block 1

Block 3

Block 5

Block 2

Block 4

Block 6

TA870U3+/TA870B

RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure.

RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media.


Drives: Minimum 2, and maximum is 2.

Uses: RAID 1 is ideal for small databases or any other application that requires fault tolerance and minimal capacity.

Benefits: Provides 100% data redundancy. Should one drive fail, the controller switches to the other drive.

Drawbacks: Requires 2 drives for the storage space of one drive.

Performance is impaired during drive rebuilds.

Fault Tolerance: Yes.

Block 1

Block 2

Block 3

Block 1

Block 2

Block 3

19


RAID 10:

RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10 solution for improved resiliency, performance and rebuild performance.


Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.

Benefits: Optimizes for both fault tolerance and performance, allowing for automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks.

Drawbacks: Requires twice the available disk space for data redundancy, the same as RAID level 1.


Block 1

Block 3

Block 5

Block 1

Block 3

Block 5

Block 2

Block 4

Block 6

Block 2

Block 4

Block 6

20

TA870U3+/TA870B

RAID 5:

RAID 5 stripes both data and parity information across three or more drives. It writes data and parity blocks across all the drives in the array. Fault tolerance is maintained by ensuring that the parity information for any given block of data is placed on a different drive from those used to store the data itself.


Drives: Minimum 3.

Uses: RAID 5 is recommended for transaction processing and general purpose service.

Benefits: An ideal combination of good performance, good fault tolerance, and high capacity and storage efficiency.

Drawbacks: Individual block data transfer rate same as a single disk. Write performance can be CPU intensive.


Disk 1

DATA 1

DATA 3

PARITY

DATA 7

DATA 9

PARITY

Disk 2

DATA 2

PARITY

DATA 5

DATA 8

PARITY

DATA 11

Disk 3

PARITY

DATA 4

DATA 6

PARITY

DATA 10

DATA 12

21


CHAPTER 5: T-SERIES BIOS & SOFTWARE

5.1 T-S

ERIES

BIOS

T-Series BIOS Features

Overclocking Navigator Engine (O.N.E.)

Memory Integration Test (M.I.T., under Overclock Navigator Engine)

BIO-Flasher: Update BIOS file from USB Flash Drive or FDD

Self Recovery System (S.R.S)

Smart Fan Function

CMOS Reloading Program

!! WARNING !!

For better system performance, the BIOS firmware is being continuously updated. The BIOS information described below in this manual is for your reference only and the actual BIOS information and settings on board may be different from this manual. For further information of setting up the BIOS, please refer to the BIOS Manual in the Setup CD.

A. Overclocking Navigator Engine (O.N.E.)

ONE provides two powerful overclocking engines: MOS and AOS for both

Elite and Casual overclockers.

Main Advanced PCIPnP

BIOS SETUP UTILITY

Chipset T-Series Exit

T-Series Settings Options

Notice: Please Clear CMOS if system no display

after overclocking.

Disabled

Enabled

BIO-unlocKING [Disabled]

OverClock Navigator [Normal]

=========== Automate OverClock System ===========

Auto OverClock System [V6-Tech Engine]

============ Manual OverClock System ============

CPU/HT Reference Clock (MHz) [200]

CPU Configuration [Auto]

Spread Spectrum [Disabled]

> Over Voltage Configuration

> CPU FID/VID Control

> Hyper Transport Configuration

> DRAM Timing Configuration

> G.P.U Phase Control

Integrated Memory Test [Disabled]

+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit

Exit vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

22

TA870U3+/TA870B

Manual Overclock System (M.O.S.)

MOS is designed for experienced overclock users.

It allows users to customize personal overclock settings.



Chipset T-Series Exit






Options

Normal

Automate OverClock

Manual OverClock








Main

Normal



+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit


↓

Advanced PCIPnP


Boot Chipset T-Series Exit




Disabled

Enabled


OverClock Navigator [Manual OverClock]




CPU/HT Reference Clock (MHZ) [200]



> Over-Voltage Configuration






+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit


BIO-unlocKING

This item allows you to activate BIO-unlocKING function.

CPU/HT Reference Clock (MHz)

CPU Frequency is directly in proportion to system performance. To maintain the system stability, CPU voltage needs to be increased also when raising CPU frequency.

CPU Configuration

This item provides several fixed modes of CPU configuration.

Spread Spectrum

This item allows you to control Spread Spectrum function.

23


Over-Voltage Configuration

Enter this function for more advanced voltage settings.

CPU FID/VID Control

Enter this function for more advanced CPU settings.

Hyper Transport Configuration

Enter this function for more advanced Hyper Transport settings.

DRAM Timing Configuration

Enter this function for more advanced DRAM clock settings.

G.P.U Phase Control

Enter this function for more power saving settings.

NOTE

Overclock is an optional process, but not a “must-do” process; it is not recommended for inexperienced users. Therefore, we will not be responsible for any hardware damage which may be caused by overclocking. We also would not guarantee any overclocking performance.

Automatic Overclock System (A.O.S.)

For beginners in overclock field, BET had developed an easy, fast, and powerful feature to increase the system performance, named A.O.S.

Based on many tests and experiments, A.O.S. provides 3 ideal overclock configurations that are able to raise the system performance in a single step.









Options

Normal










Normal



+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit


24

TA870U3+/TA870B

V6 Tech Engine

This engine will make a good over-clock performance.








OverClock Navigator [Automate OverClock]













V6-Tech Engine

V8-Tech Engine

V12-Tech Engine

+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit


V8 Tech Engine

This engine will make a better over-clock performance.





















V6-Tech Engine

V8-Tech Engine

V12-Tech Engine

+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit


V12 Tech Engine

This engine will make a best over-clock performance.





















V6-Tech Engine

V8-Tech Engine

V12-Tech Engine

+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit


25


Notices:

Not all types of AMD CPU perform above overclock setting ideally; the difference will be based on the selected CPU model.

B. Memory Integration Test (M.I.T.)

This function is under “Overclocking Navigator Engine” item.

MIT allows users to test memory compatibilities, and no extra devices or software are needed.

Step 1

The default setting under this item is “Disabled”; the condition parameter should be changed to “Enable” to proceed this test.







Enabled

Disabled















+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit



↓






Enabled

Disabled














Integrated Memory Test [Enabled]

+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit


Step 2

Save and Exit from CMOS setup and reboot the system to activate this test.

Run this test for 5 minutes (minimum) to ensure the memory stability.

Step 3

When the process is done, change the setting back from “Enable” to “Disable” to complete the test.

26

TA870U3+/TA870B

C. BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>

during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the

USB port or the floppy disk drive.

4. Power on or reset the computer and then press <F12> during the POST process.

A select dialog as the picture on the right appears.

Select the device contains the BIOS file and press <Enter> to enter the utility.

5. The utility will show the BIOS files and their respective information. Select the proper

BIOS file and press <Enter> then <Y> to perform the BIOS update process.

6. After the update process, the utility will ask you to reboot the system.

Press <Y> to proceed. BIOS update completes. z This utility only allows storage device with FAT32/16 format and single partition. z Shutting down or resetting the system while updating the BIOS will lead to system boot failure.

27


D. Self Recovery System (S.R.S.)

This function can’t be seen under BIOS setup; and is always on whenever the system starts up.

However, it can prevent system hang-up due to inappropriate overclock actions.

When the system hangs up, S.R.S. will automatically log in the default BIOS setting, and all overclock settings will be re-configured.

E. Smart Fan Function

Smart Fan Function is under “Smart Fan Configuration” in “Advanced Menu”.

This is a brilliant feature to control CPU/System Temperature vs. Fan speed.

When enabling Smart Fan function, Fan speed is controlled automatically by

CPU/System temperature.

This function will protect CPU/System from overheat problem and maintain the system temperature at a safe level.




Advanced Settings

WARNING: Setting wrong values in below sections

may cause system to malfunction.

> CPU Configuration

> SuperIO Configuration

> Smart Fan Configuration

> Hardware Health Configuration

> Power Configuration

> USB Configuration

Configure CPU.

Enter

F1

F10

ESC

Select Screen

Select Item

Go to Sub Screen

General Help

Save and Exit


↓


Advanced

Smart Fan Configuration

CPU Smart Fan [Disabled]

Smart Fan Calibration

Control Mode

Fan Ctrl OFF( C)

Fan Ctrl On( C)

Fan Ctrl Start value

Fan Ctrl Sensitive

When you choice [Auto]

,[3Pin] or [4Pin], please run the calibration to define the Fan parameters for

Smart Fan control

+-

F1

F10

ESC

Select Screen

Select Item

Change Option

General Help

Save and Exit


28

TA870U3+/TA870B

Smart Fan Calibration

Choose this item and then the BIOS will automatically test and detect the

CPU/System fan functions and show CPU/System fan speed.

Control Mode

This item provides several operation modes of the fan.

Fan Ctrl OFF(℃)

If the CPU/System temperature is lower than the set value, the CPU/

System fan will turn off. The range is from 0~127, with an interval of 1.

Fan Ctrl On(℃)

The CPU/System fan starts to work when CPU/System temperature arrives to this set value. The range is from 0~127, with an interval of 1.

Fan Ctrl Start Value

When CPU/System temperature arrives to the set value, the CPU/System fan will work under Smart Fan Function mode. The range is from 0~127, with an interval of 1.

Fan Ctrl Sensitive

Increasing the value of slope PWM will raise the speed of CPU/System fan.

The range is from 1~127, with an interval of 1.

F. CMOS Reloading Program

It allows users to save different CMOS settings into BIOS-ROM.

Users are able to reload any saved CMOS setting for customizing system configurations. Moreover, users are able to save an ideal overclock setting during overclock operation.

There are 10 sets of record addresses in total, and users are able to name the

CMOS data according to personal preference.




Exit Options

Save Changes and Exit

Discard Changes and Exit

Discard Changes

Load Optimal Defaults

CMOS Backup Function

CMOS Backup Func

CMOS Data

CMOS Data

Reload

Save

Security Settings

> Security

Enter

F1

F10

ESC

Select Screen

Select Item

Go to Sub Screen

General Help

Save and Exit


29


5.2 T-S

ERIES

S

OFTWARE

Installing T-Series Software

1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Auto-run function has been enabled.

2. Select title.

3. Follow the on-screen instructions to complete the installation.

Launching T-Series Software

After the installation process is completed, you will see the software icon showing on the desktop. Double-click the icon to launch it.

TOverclocker

TOverclocker presents a simple Windows-based system performance enhancement and manageability utility. It features several powerful and easy to use tools such as Overclocking for enhancing system performance, also for special enhancement on CPU and Memory. Smart-Fan management and PC health are for monitoring system status.This utility also allows you to make overclocking profiles saving unlimitedly, and pre-set OC modes are for easy

OC. (The illustration below is for reference only)

30

TA870U3+/TA870B

The CPU tab provides information on the CPU and motherboard.

The Memory tab provides information on the memory module(s).

You can select memory module on a specific slot to see its information.

The OC Tweaker tab allows you to change system clock settings and voltages settings. It also provides six pre-set modes for you:

31


Six Pre-set Modes: V3, V6, V9, V12, V15, AUTO for different overclocking experience.

The HW Monitor tab allows you to monitor hardware voltage, fan speed, and temperature. Besides, you also can set related values for CPU Smart Fan.

32

TA870U3+/TA870B

Pressing TOVERCLOCKER logo will display information about manufacturer and software version.

You can update currnet version by clicking the button “Live Update.”

Green Power II Utility

BIOSTAR G.P.U II (Green Power Utility) is a new function. The utility enhances energy efficiency by disabling extra phases while CPU is on light loading; it features 4+1 power phases, current power saving, and toal power saving. This tool integrates a friendly GUI to monitor your CPU Usage, CPU Watt, and CPU

Temperature. Moreover, it optimizes power saving and best power efficiency on your system. (The illustration below is for reference only)

Typical Mode

Display manufacturer & software version information

Performance

Mode

Medium Mode

Maxi-Energy Mode

Auto P hase Mode

Display CPU information

Reset Time &

Consumption

33


G.P.U Mode Setting

This utility provides five modes, upon your requirements, to improve system performance or to save power consumption.

Note: Even if the modes saving more power consumption are chosen, the system still can keep excellent performance.

Auto Phase Mode

System switches the mode automatically according to current system loading condition.

Performance Mode

This is the mode saving power consumption most. Least energy will be used in the system.

Typical Mode

Compared with that in Performance Mode, energy consumption in this mode is a little bit more.

Medium Mode

This is the standard system power saving mode.

Maxi-Energy Mode

This is the best system performance mode.

34

TA870U3+/TA870B

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our

Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem.

Before you use this utility, please set Outlook Express as your default e-mail client application program.

* represent s import ant information that you must provide. Without this informat ion, you may not be able to send out the mail.

This block will show the information which would be collect ed in the mail.

* Describe condition of your system.

* Select your area or the area close to you.

Provide the e-mail address that you would like to send t he copy to.

* Provide the name of the memory module manufacturer.

Send the mail out.

Exit this dialog.

Save these information to a .txt file

Provide the name of the power supply manufacturer and the model no.

After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click

“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name.

35


Enter the file name and then click

“Save”. Your system information will be saved to a .txt file.

Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail.

We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service.

If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application.

Go to the following web http://www.biostar.com.tw/app/en-us/about/contact.php

for getting our contact information.

36

TA870U3+/TA870B

BIOS Update

BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system.

AWARD BIOS

Show current BIOS information

AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Save current BIOS to a .bin file

Online Update function

(Only for AMI BIOS)

Update BIOS with a BIOS file

<Backup BIOS>

Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.)

Then click Save.

37


<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS procedure should be run with Clear CMOS function, so please check on Clear CMOS first.

Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure.

After the BIOS Backup procedure, the open dialog will show for requesting the

BIOS file which is going to be updated.

Please choose the proper BIOS file for updating, then click on Open.

The utility will update BIOS with the proper BIOS file, and this process may take minutes. Please do not open any other applications during this process.

After the BIOS Update process, click on

OK to restart the system.

While the system boots up and the full screen logo shows, press key to enter BIOS setup.

<Delete>

In the BIOS setup, use the Load Optimized Defaults function and then Save and

Exit Setup to exit BIOS setup. BIOS Update is completed.

38

TA870U3+/TA870B

<Online Update> (for AMI BIOS only)

Automatically download and update the latest BIOS via internet; make sure

that the computer is connected to the internet before using this function.

After clicking on the Onlinr Update button, the utility will search for the latest BIOS from internet. If there is a new BIOS version, the utility will ask you to download it. Click Yes to proceed.

If there is no other newer BIOS version, the utility will also tell you that your BIOS has been the latest version.

Download completes; the utility will ask you to program (update) the

BIOS. Click Yes to proceed.

The programing procedure may take minutes, please do not make any operation

during the programing process.

After the updating process, the utility will ask you to reboot the system. Click OK to reboot.

While the system boots up and the full screen logo shows, press key to enter BIOS setup.

<Delete>

In the BIOS setup, use the Load Optimized Defaults function and then Save and

Exit Setup to exit BIOS setup. Online Update is completed.

All the information and content above about the T-Series software are subject to be changed without notice. For better performance, the software is being continuously updated. The information and pictures described above are for your reference only.

The actual information and settings on board may be slightly different from this manual.

39


CHAPTER 6: USEFUL HELP

6.1 D

RIVER

I

NSTALLATION

N

OTE

After you installed your operating system, please insert the Fully Setup

Driver CD into your optical drive and install the driver for better system performance.

You will see the following window after you insert the CD

40

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system.

Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver

CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from

http://www.adobe.com/products/acrobat/readstep2.html

TA870U3+/TA870B

6.2 E

XTRA

I

NFORMATION

CPU Overheated

If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.

(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

41


6.3 AMI BIOS B

EEP

C

ODE

Boot Block Beep Codes

Number of Beeps

1

2

3

4

5

7

10

11

12

13

Description

No media present. (Insert diskette in floppy drive A:)

“AMIBOOT.ROM” file not found in root directory of diskette in

A:

Insert next diskette if multiple diskettes are used for recovery

Flash Programming successful

File read error

No Flash EPROM detected

Flash Erase error

Flash Program error

“AMIBOOT.ROM” file size error

BIOS ROM image mismatch (file layout does not match image present in flash device)

POST BIOS Beep Codes

Number of Beeps

1

3

6

7

8

Description

Memory refresh timer error

Base memory read/write test error

Keyboard controller BAT command failed

General exception error (processor exception interrupt error)

Display memory error (system video adapter)

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action

1, 3

6, 7

8

Reseat the memory, or replace with known good modules.

Fatal error indicating a serious problem with the system.

Consult your system manufacturer. Before declaring the motherboard beyond all hope, eliminate the possibility of interference by a malfunctioning add-in card. Remove all expansion cards except the video adapter. z If beep codes are generated when all other expansion cards are absent, consult your system manufacturer’s technical support. z If beep codes are not generated when all other expansion cards are absent, one of the add-in cards is causing the malfunction. Insert the cards back into the system one at a time until the problem happens again. This will reveal the malfunctioning card.

If the system video adapter is an add-in card, replace or reseat the video adapter. If the video adapter is an integrated part of the system board, the board may be faulty.

42

TA870U3+/TA870B

6.4 AMI BIOS P

OST

C

ODE

Checkpoint Description

03

04

05

06

07

08

C0

C1

C2

C5

C6

C7

0A

0B

0C

0E

13

20

24

2A

2C

2E

31

33

Disable NMI, Parity, video for EGA, and DMA controllers. Initialize BIOS,

POST, Runtime data area. Also initialize BIOS modules on POST entry and

GPNV area. Initialized CMOS as mentioned in the Kernel Variable

"wCMOSFlags."

Check CMOS diagnostic byte to determine if battery power is OK and

CMOS checksum is OK. Verify CMOS checksum manually by reading storage area. If the CMOS checksum is bad, update CMOS with power-on default values and clear passwords. Initialize status register A.

Initializes data variables that are based on CMOS setup questions.

Initializes both the 8259 compatible PICs in the system

Initializes the interrupt controlling hardware (generally PIC) and interrupt vector table.

Do R/W test to CH-2 count reg. Initialize CH-0 as system timer. Install the

POSTINT1Ch handler. Enable IRQ-0 in PIC for system timer interrupt.

Traps INT1Ch vector to "POSTINT1ChHandlerBlock."

Fixes CPU POST interface calling pointer.

Initializes the CPU. The BAT test is being done on KBC. Program the keyboard controller command byte is being done after Auto detection of

KB/MS using AMI KB-5.

Early CPU Init Start -- Disable Cache – Init Local APIC.

Set up boot strap processor Information.

Set up boot strap processor for POST.

Enumerate and set up application processors.

Re-enable cache for boot strap processor.

Early CPU Init Exit.

Initializes the 8042 compatible Key Board Controller.

Detects the presence of PS/2 mouse.

Detects the presence of Keyboard in KBC port.

Testing and initialization of different Input Devices. Also, update the Kernel

Variables.

Traps the INT09h vector, so that the POST INT09h handler gets control for

IRQ1. Uncompress all available language, BIOS logo, and Silent logo modules.

Early POST initialization of chipset registers.

Relocate System Management Interrupt vector for all CPU in the system.

Uncompress and initialize any platform specific BIOS modules. GPNV is initialized at this checkpoint.

Initializes different devices through DIM.

See DIM Code Checkpoints section of document for more information.

Initializes different devices. Detects and initializes the video adapter installed in the system that have optional ROMs.

Initializes all the output devices.

Allocate memory for ADM module and uncompress it. Give control to ADM module for initialization. Initialize language and font modules for ADM.

Activate ADM module.

Initializes the silent boot module. Set the window for displaying text information.

43


Checkpoint Description

37

38

39

Displaying sign-on message, CPU information, setup key message, and any

OEM specific information.

Initializes different devices through DIM. See DIM Code Checkpoints section of document for more information. USB controllers are initialized at this point.

Initializes DMAC-1 & DMAC-2.

AC

B1

00

3B

3C

40

52

60

75

78

7C

84

85

87

8C

8D

8E

90

A1

A2

A4

A7

A9

AA

Test for total memory installed in the system. Also, Check for DEL or ESC keys to limit memory test. Display total memory in the system.

Mid POST initialization of chipset registers.

Detect different devices (Parallel ports, serial ports, and coprocessor in

CPU, etc.) successfully installed in the system and update the BDA,

EBDA…etc.

Updates CMOS memory size from memory found in memory test. Allocates memory for Extended BIOS Data Area from base memory. Programming the memory hole or any kind of implementation that needs an adjustment in system RAM size if needed.

Initializes NUM-LOCK status and programs the KBD typematic rate.

Initialize Int-13 and prepare for IPL detection.

Initializes IPL devices controlled by BIOS and option ROMs.

Generate and write contents of ESCD in NVRam.

Log errors encountered during POST.

Display errors to the user and gets the user response for error.

Execute BIOS setup if needed / requested. Check boot password if installed.

Late POST initialization of chipset registers.

Build ACPI tables (if ACPI is supported).

Program the peripheral parameters. Enable/Disable NMI as selected.

Initialization of system management interrupt by invoking all handlers.

Please note this checkpoint comes right after checkpoint 20h.

Clean-up work needed before booting to OS.

Takes care of runtime image preparation for different BIOS modules. Fill the free area in F000h segment with 0FFh. Initializes the Microsoft IRQ Routing

Table. Prepares the runtime language module. Disables the system configuration display if needed.

Initialize runtime language module. Display boot option popup menu.

Displays the system configuration screen if enabled. Initialize the CPU’s before boot, which includes the programming of the MTRR’s.

Wait for user input at config display if needed.

Uninstall POST INT1Ch vector and INT09h vector.

End of POST initialization of chipset registers. De-initializes the ADM module.

Save system context for ACPI. Prepare CPU for OS boot including final

MTRR values.

Passes control to OS Loader (typically INT19h).

44

TA870U3+/TA870B

6.5 T

ROUBLESHOOTING

Probable Solution

1. There is no power in the system.

Power LED does not shine; the fan of the power supply does not work

2. Indicator light on keyboard does not shine.

1. Make sure power cable is securely plugged in.

3. Contact technical support.

System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running.

System does not boot from a hard disk drive, but can be booted from optical drive.

System only boots from an optical drive. Hard disks can be read, applications can be used, but system fails to boot from a hard disk.

Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place.

1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup.

2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time.

1. Back up data and applications files.

2. Reformat the hard drive.

Re-install applications and data using backup disks.

Screen message shows “Invalid

Configuration” or “CMOS Failure.”

Review system’s equipment. Make sure correct information is in setup.

System cannot boot after user installs a second hard drive.

1. Set master/slave jumpers correctly.

2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.

45


APPENDIX: SPEC IN OTHER LANGUAGES

G

ERMAN

Sockel AM3

CPU

TA870U3+ TA870B

Sockel AM3

AMD Phenom II/Athlon II/Sempron Prozessoren AMD Phenom II/Athlon II/Sempron Prozessoren

Die AMD 64-Architektur unterstützt eine 32-Bit- Die AMD 64-Architektur unterstützt eine 32-Bit- und 64-Bit-Datenverarbeitung und 64-Bit-Datenverarbeitung

Unterstützt Hyper Transport 3.0 und Cool’n’Quiet Unterstützt Hyper Transport 3.0 und Cool’n’Quiet

(Maximales Watt: 140W) (Maximales Watt: 140W)

FSB

Chipsatz

Super E/A

Arbeitsspeich er

Unterstützt HyperTransport 3.0 mit einer

Bandbreite von bis zu 5.2 GT/s

AMD 870

AMD SB850

ITE 8728

Bietet die häufig verwendeten alten Super

E/A-Funktionen.

Low Pin Count-Schnittstelle

Umgebungskontrolle,

Hardware-Überwachung

"Smart Guardian"-Funktion von ITE

DDR3 DIMM-Steckplätze x 4

Max. 16GB Arbeitsspeicher

Jeder DIMM unterstützt 512MB/ 1GB/2GB/

4GB DDR3.

Dual-Kanal DDR3 Speichermodul

Unterstützt DDR3 800 / 1066 / 1333

Unterstützt DDR3 1600 (OC) registrierte DIMMs. ECC DIMMs werden nicht unterstützt.

Unterstützt HyperTransport 3.0 mit einer

Bandbreite von bis zu 5.2 GT/s

AMD 870

AMD SB850

ITE 8728

Bietet die häufig verwendeten alten Super

E/A-Funktionen.

Low Pin Count-Schnittstelle

Umgebungskontrolle,

Hardware-Überwachung

"Smart Guardian"-Funktion von ITE

DDR3 DIMM-Steckplätze x 4

Max. 16GB Arbeitsspeicher

Jeder DIMM unterstützt 512MB/ 1GB/2GB/

4GB DDR3.

Dual-Kanal DDR3 Speichermodul

Unterstützt DDR3 800 / 1066 / 1333

Unterstützt DDR3 1600 (OC) registrierte DIMMs. ECC DIMMs werden nicht unterstützt.

SATA 3

LAN

HD

Audio-Unters tützung

Steckplätze

Integrierter Serial ATA-Controller

Datentransferrate bis zu 6 Gb/s

Integrierter Serial ATA-Controller

Datentransferrate bis zu 6 Gb/s

Konform mit der SATA-Spezifikation Version 3.0. Konform mit der SATA-Spezifikation Version 3.0.

Realtek RTL 8111E

10 / 100 / 1000 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

ALC662

5.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

PCI Express Gen2 x16 Steckplatz x2

PCI Express Gen2 x 1-Steckplatz x2

Realtek RTL 8111E

10 / 100 / 1000 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

ALC662

5.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

PCI Express Gen2 x16 Steckplatz x2

PCI Express Gen2 x 1-Steckplatz x2

46

TA870U3+

TA870U3+/TA870B

TA870B

S/PDIF- Ausgangsanschluss x1 S/PDIF- Ausgangsanschluss x1

Onboard-Ans chluss "CMOS löschen"-Sockel

USB 2.0-Anschluss x1 x3

"CMOS löschen"-Sockel

USB 2.0-Anschluss x1 x3

Stromanschluss (4-polig)

Verbraucher-IR Anschluss x1 x1

Stromanschluss (4-polig)

Verbraucher-IR Anschluss x1 x1

Rückseiten-E

/A

Druckeranschluss Anschluss

PS/2-Tastatur

PS/2-Maus

Serieller Anschluss x1 x1 x1 x1

Platinengröße 220 mm (B) X 305 mm (L)

Sonderfunkti onen

Unterstützt RAID 0 / 1 / 10 / 5


Biostar behält sich das Recht vor, ohne

OS-Unterstüt zung

Ankündigung die Unterstützung für ein

Betriebssystem hinzuzufügen oder zu entfernen.

Druckeranschluss Anschluss

PS/2-Tastatur

PS/2-Maus x1

USB 2.0-Anschluss (durch SB850) x2

USB 3.0-Anschlus

LAN-Anschluss x1

USB 2.0-Anschluss x4

(durch ASM1042) x2 Audioanschluss x3

Audioanschluss x3

220 mm (B) X 305 mm (L)

Unterstützt RAID 0 / 1 / 10 / 5


Ankündigung die Unterstützung für ein

Betriebssystem hinzuzufügen oder zu entfernen. x1 x1 x1

Biostar behält sich das Recht vor, ohne

47


UC

F

RENCH

Socket AM3

TA870U3+ TA870B

Socket AM3

Processeurs AMD Phenom II/Athlon II/Sempron Processeurs AMD Phenom II/Athlon II/Sempron

L'architecture AMD 64 permet le calcul 32 et 64 L'architecture AMD 64 permet le calcul 32 et 64

Bus frontal

Chipset bits

Prend en charge Hyper Transport 3.0 et

Cool’n’Quiet

(Watt maximum : 140W) bits

Prend en charge Hyper Transport 3.0 et

Cool’n’Quiet

(Watt maximum : 140W)

Prend en charge Hyper Transport 3.0 jusqu'à une Prend en charge Hyper Transport 3.0 jusqu'à une bande passante de 5.2 GT/s bande passante de 5.2 GT/s

AMD 870

AMD SB850

AMD 870

AMD SB850

Super E/S

Mémoire principale

SATA 3

LAN

Prise en charge audio HD

Fentes

ITE 8728

Fournit la fonctionnalité de Super E/S patrimoniales la plus utilisée.

Interface à faible compte de broches

Initiatives de contrôle environnementales,

Moniteur de matériel

Fonction "Gardien intelligent" de l'ITE

ITE 8728

Fournit la fonctionnalité de Super E/S patrimoniales la plus utilisée.

Interface à faible compte de broches

Initiatives de contrôle environnementales,

Moniteur de matériel

Fonction "Gardien intelligent" de l'ITE

Fentes DDR3 DIMM x 4

Capacité mémoire maximale de 16 Go

Fentes DDR3 DIMM x 4

Capacité mémoire maximale de 16 Go

Chaque DIMM prend en charge des DDR3 de 512 Chaque DIMM prend en charge des DDR3 de 512

Mo et 1Go/2Go/4Go Mo et 1Go/2Go/4Go

Module de mémoire DDR3 à mode à double voie Module de mémoire DDR3 à mode à double voie

Prend en charge la DDR3 800 / 1066 / 1333

Prend en charge la DDR3 1600 (OC)

Prend en charge la DDR3 800 / 1066 / 1333

Prend en charge la DDR3 1600 (OC)

Les DIMM à registres et DIMM avec code correcteurs d'erreurs ne sont pas prises en charge

Les DIMM à registres et DIMM avec code correcteurs d'erreurs ne sont pas prises en charge

Contrôleur Serial ATA intégré

Taux de transfert jusqu'à 6 Go/s.

Conforme à la spécification SATA Version 3.0

Contrôleur Serial ATA intégré

Taux de transfert jusqu'à 6 Go/s.

Conforme à la spécification SATA Version 3.0

Realtek RTL 8111E Realtek RTL 8111E

10 / 100 / 1000 Mb/s négociation automatique 10 / 100 / 1000 Mb/s négociation automatique


ALC662

Sortie audio à 5.1 voies

Prise en charge de l'audio haute définition

Fente PCI Express Gen2 x16 x2

Fente PCI Express Gen2 x1

Fente PCI x2 x2


ALC662

Sortie audio à 5.1 voies

Prise en charge de l'audio haute définition



Fente PCI x2 x2 x2

48

TA870U3+

Connecteur SATA

Connecteur du panneau avant x6 x1

Connecteur Audio du panneau avant x1

Connecteur de sortie S/PDIF x1

Embase de ventilateur UC x1

Connecteur embarqué

Embase de ventilateur système

Embase d'effacement CMOS

Connecteur USB 2.0

Connecteur d'alimentation

(24 broches)


(4 broches)

Connecteur de IR du consommateur x2 x1 x3 x1 x1

TA870U3+/TA870B

TA870B

Connecteur SATA

Connecteur du panneau avant x6 x1

Connecteur Audio du panneau avant x1

Connecteur de sortie S/PDIF x1

Embase de ventilateur UC x1

Embase de ventilateur système

Embase d'effacement CMOS

Connecteur USB 2.0

Connecteur d'alimentation x2 x1 x3 x1

(24 broches)


(4 broches)

Connecteur de IR du consommateur x1

E/S du panneau arrière

Connecteur de Port d'imprimante x1

Clavier PS/2

Souris PS/2

Port série

Port LAN

Port USB 2.0 (par SB850)

Port USB 3.0 (par ASM1042)

Fiche audio x1 x1 x1 x1 x2 x2 x3

Connecteur de Port d'imprimante

Clavier PS/2

Souris PS/2

Port série

Port LAN

Port USB 2.0

Fiche audio x1 x1 x1 x1 x1 x4 x3

Dimensions

220 mm (l) X 305 mm (H) de la carte

Fonctionnali tés spéciales

Prise en charge RAID 0 / 1 / 10 / 5


220 mm (l) X 305 mm (H)

Prise en charge RAID 0 / 1 / 10 / 5


Support SE Biostar se réserve le droit d'ajouter ou de Biostar se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis. supprimer le support de SE avec ou sans préavis.

49


I

TALIAN

TA870U3+ TA870B

Socket AM3 Socket AM3

Processori AMD Phenom II/Athlon II/Sempron Processori AMD Phenom II/Athlon II/Sempron

CPU

L’architettura AMD 64 abilita la computazione 32 e 64 bit

Supporto di Hyper Transport 3.0 e

Cool’n’Quiet

(Watt massimo: 140W)

L’architettura AMD 64 abilita la computazione 32 e 64 bit

Supporto di Hyper Transport 3.0 e

Cool’n’Quiet

(Watt massimo: 140W)

FSB

Chipset

Supporto di HyperTransport 3.0 fino a 5.2

GT/s di larghezza di banda

AMD 870

AMD SB850

ITE 8728

Super I/O

Fornisce le funzionalità legacy Super I/O usate più comunemente.

Interfaccia LPC (Low Pin Count)

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Funzione "Smart Guardian" di ITE

Alloggi DIMM DDR3 x 4

Memoria principale

Capacità massima della memoria 16GB

Ciascun DIMM supporta DDR3 512MB e

1GB/2GB/4GB

Modulo di memoria DDR3 a canale doppio

Supporto di DDR3 800 / 1066 / 1333

Supporto di DDR3 1600 (OC)

DIMM registrati e DIMM ECC non sono supportati

Supporto di HyperTransport 3.0 fino a 5.2

GT/s di larghezza di banda

AMD 870

AMD SB850

ITE 8728

Fornisce le funzionalità legacy Super I/O usate più comunemente.

Interfaccia LPC (Low Pin Count)

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Funzione "Smart Guardian" di ITE

Alloggi DIMM DDR3 x 4

Capacità massima della memoria 16GB

Ciascun DIMM supporta DDR3 512MB e

1GB/2GB/4GB

Modulo di memoria DDR3 a canale doppio

Supporto di DDR3 800 / 1066 / 1333

Supporto di DDR3 1600 (OC)

DIMM registrati e DIMM ECC non sono supportati

SATA 3

LAN

Supporto audio HD

Alloggi

Controller Serial ATA integrato

Velocità di trasferimento dei dati fino a 6

Gb/s.

Compatibile specifiche SATA Versione 3.0.

Realtek RTL 8111E

Controller Serial ATA integrato

Velocità di trasferimento dei dati fino a 6

Gb/s.

Compatibile specifiche SATA Versione 3.0.

Realtek RTL 8111E

Negoziazione automatica 10 / 100 / 1000 Mb/s Negoziazione automatica 10 / 100 / 1000 Mb/s

Capacità Half / Full Duplex Capacità Half / Full Duplex

ALC662

Uscita audio 5.1 canali

Supporto audio High-Definition (HD)

Alloggio PCI Express Gen2 x16 x2


Alloggio PCI x2

ALC662

Uscita audio 5.1 canali

Supporto audio High-Definition (HD)



Alloggio PCI x2

50

TA870U3+/TA870B

TA870U3+

Connettore SATA x6

Connettore pannello frontale x1

Connettore audio frontale x1

Connettore output SPDIF

Collettore ventolina CPU x1 x1 su scheda

Collettore ventolina sistema x2

Connettori Collettore cancellazione CMOS x1

Connettore USB 2.0 x3

Connettore alimentazione

(24 pin)


(4 pin) x1 x1

Connettore IR del consumatore x1

Connettore Porta stampante

Tastiera PS/2 x1 x1

I/O pannello

Mouse PS/2

Porta seriale

Porta LAN posteriore Porta USB 2.0 (da SB850) x1 x1 x1 x2

Porta USB 3.0 (da ASM1042) x2

Connettore audio x3

Connettore SATA

(24 pin)

(4 pin)

Tastiera PS/2

Mouse PS/2

Porta seriale

Porta LAN

Porta USB 2.0

Connettore audio

TA870B

Connettore audio frontale

Connettore output SPDIF

Collettore ventolina CPU

Collettore ventolina sistema

Connettore USB 2.0


Connettore alimentazione x6

Connettore pannello frontale x1 x1 x1 x1 x2

Collettore cancellazione CMOS x1 x3 x1 x1

Connettore IR del consumatore x1

Connettore Porta stampante x1 x1 x1 x1 x1 x4 x3

Dimension i scheda

220 mm (larghezza) x 305 mm (altezza) 220 mm (larghezza) x 305 mm (altezza)

Caratterist iche Supporto RAID 0 / 1 / 10 / 5 speciali


Sistemi operativi supportati

Biostar si riserva il diritto di aggiungere o rimuovere il supporto di qualsiasi sistema operativo senza preavviso.

Supporto RAID 0 / 1 / 10 / 5


Biostar si riserva il diritto di aggiungere o rimuovere il supporto di qualsiasi sistema operativo senza preavviso.

51


S

PANISH

TA870U3+

Conector AM3

Procesadores AMD Phenom II/Athlon

TA870B

Conector AM3

Procesadores AMD Phenom II/Athlon

CPU

FSB

II/Sempron II/Sempron

La arquitectura AMD 64 permite el procesado de La arquitectura AMD 64 permite el procesado de

32 y 64 bits

Soporta las tecnologías Hyper Transport 3.0 y

Cool’n’Quiet

32 y 64 bits

Soporta las tecnologías Hyper Transport 3.0 y

Cool’n’Quiet

(Vatio máximo: 140W)

Admite HyperTransport 3.0 con un ancho de banda de hasta 5.2 GT/s

Conjunto de AMD 870 chips AMD SB850

(Vatio máximo: 140W)

Admite HyperTransport 3.0 con un ancho de banda de hasta 5.2 GT/s

AMD 870

AMD SB850

Súper E/S

Memoria principal

SATA 3

Red Local

ITE 8728

Le ofrece las funcionalidades heredadas de uso más común Súper E/S.

Interfaz de cuenta Low Pin

Iniciativas de control de entorno,

Monitor hardware

Función "Guardia inteligente" de ITE

Ranuras DIMM DDR3 x 4

Capacidad máxima de memoria de 16GB

Cada DIMM admite DDR de 512MB y

1GB/2GB/4GB

Módulo de memoria DDR3 de canal Doble

Admite DDR3 de 800 / 1066 / 1333

Admite DDR3 de 1600 (OC)

No admite DIMM registrados o DIMM compatibles con ECC

Controlador ATA Serie Integrado

Tasas de transferencia de hasta 6 Gb/s.

Compatible con la versión SATA 3.0.

Realtek RTL 8111E

Negociación de 10 / 100 / 1000 Mb/s

Funciones Half / Full dúplex

Soporte de sonido HD

Ranuras

ALC662

Salida de sonido de 5.1 canales

Soporte de sonido Alta Definición

Ranura PCI Express Gen2 x16

Ranura PCI Express Gen2 x 1

Ranura PCI

X2

X2

X2

ITE 8728

Le ofrece las funcionalidades heredadas de uso más común Súper E/S.

Interfaz de cuenta Low Pin

Iniciativas de control de entorno,

Monitor hardware

Función "Guardia inteligente" de ITE

Ranuras DIMM DDR3 x 4

Capacidad máxima de memoria de 16GB

Cada DIMM admite DDR de 512MB y

1GB/2GB/4GB

Módulo de memoria DDR3 de canal Doble

Admite DDR3 de 800 / 1066 / 1333

Admite DDR3 de 1600 (OC)

No admite DIMM registrados o DIMM compatibles con ECC

Controlador ATA Serie Integrado

Tasas de transferencia de hasta 6 Gb/s.

Compatible con la versión SATA 3.0.

Realtek RTL 8111E

Negociación de 10 / 100 / 1000 Mb/s

Funciones Half / Full dúplex

ALC662

Salida de sonido de 5.1 canales

Soporte de sonido Alta Definición

Ranura PCI Express Gen2 x16

Ranura PCI Express Gen2 x 1

Ranura PCI

X2

X2

X2

52

TA870U3+/TA870B

TA870U3+

Conector SATA

Conector de panel frontal

Conector de sonido frontal

Conector de salida S/PDIF

Cabecera de ventilador de CPU

Conectores en placa

Cabecera de ventilador de sistema X2

Cabecera de borrado de CMOS X1

Conector USB 2.0 X3

X1 Conector de alimentación

(24 patillas)

Conector de alimentación

(4 patillas)

Conector de IR del consumidor

Conector Puerto de impresora

X1

X1

X1

X6

X1

X1

X1

X1

Conector SATA

TA870B

Conector de panel frontal

Conector de sonido frontal

Conector de salida S/PDIF

Cabecera de ventilador de CPU

X6

X1

X1

X1

X1

Cabecera de ventilador de sistema X2

Cabecera de borrado de CMOS X1

Conector USB 2.0 X3


(24 patillas)


(4 patillas)

Conector de IR del consumidor

Conector Puerto de impresora

X1

X1

X1

X1

Teclado PS/2 X1

X1

X1

X1

X2

X2

Teclado PS/2 X1

Panel trasero de

E/S

Ratón PS/2

Puerto serie

Puerto de red local

Puerto USB 2.0 (por SB850)

Puerto USB 3.0 (por ASM1042)

Ratón PS/2

Puerto serie

Puerto de red local

Puerto USB 2.0

Conector de sonido

X1

X1

X1

X4

X3

Funciones especiales

Conector de sonido

Tamaño de la placa

220 mm. (A) X 305 Mm. (H)

Admite RAID 0 / 1 / 10 / 5

Soporte de sistema operativo

X3


Biostar se reserva el derecho de añadir o retirar el soporte de cualquier SO con o sin aviso previo.

220 mm. (A) X 305 Mm. (H)

Admite RAID 0 / 1 / 10 / 5


Biostar se reserva el derecho de añadir o retirar el soporte de cualquier SO con o sin aviso previo.

53


P

ORTUGUESE

TA870U3+ TA870B

Socket AM3 Socket AM3

CPU

FSB

Chipset

Processadores AMD Phenom II/Athlon

II/Sempron

Processadores AMD Phenom II/Athlon

II/Sempron

A arquitectura AMD 64 permite uma computação A arquitectura AMD 64 permite uma computação de 32 e 64 bits

Suporta as tecnologias Hyper Transport 3.0 e

Cool’n’Quiet de 32 e 64 bits

Suporta as tecnologias Hyper Transport 3.0 e

Cool’n’Quiet

(Watt máximo: 140W)

Suporta a tecnologia HyperTransport 3.0 com uma largura de banda até 5.2 GT/s

AMD 870

AMD SB850

ITE 8728

Proporciona as funcionalidades mais utilizadas

Especificaçã o Super I/O em termos da especificação Super I/O.

Interface LPC (Low Pin Count).

Iniciativas para controlo do ambiente

Monitorização do hardware

Memória principal

Função "Smart Guardian" da ITE

Ranhuras DIMM DDR3 x 4

Capacidade máxima de memória: 16 GB

Cada módulo DIMM suporta uma memória

DDR3 de 512 MB & 1 GB/2 GB/4 GB

Módulo de memória DDR3 de canal duplo

Suporta módulos DDR3 800 / 1066 / 1333

Suporta módulos DDR3 1600 (OC)

Os módulos DIMM registados e os DIMM ECC não são suportados

(Watt máximo: 140W)

Suporta a tecnologia HyperTransport 3.0 com uma largura de banda até 5.2 GT/s

AMD 870

AMD SB850

ITE 8728

Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O.

Interface LPC (Low Pin Count).

Iniciativas para controlo do ambiente

Monitorização do hardware

Função "Smart Guardian" da ITE

Ranhuras DIMM DDR3 x 4

Capacidade máxima de memória: 16 GB

Cada módulo DIMM suporta uma memória

DDR3 de 512 MB & 1 GB/2 GB/4 GB

Módulo de memória DDR3 de canal duplo

Suporta módulos DDR3 800 / 1066 / 1333

Suporta módulos DDR3 1600 (OC)

Os módulos DIMM registados e os DIMM ECC não são suportados

SATA 3

LAN

Controlador Serial ATA integrado Controlador Serial ATA integrado

Velocidades de transmissão de dados até 6 Gb/s. Velocidades de transmissão de dados até 6 Gb/s.

Compatibilidade com a especificação SATA versão 3.0.

Compatibilidade com a especificação SATA versão 3.0.

Realtek RTL 8111E

Auto negociação de 10 / 100 / 1000 Mb/s

Capacidade semi/full-duplex

Realtek RTL 8111E

Auto negociação de 10 / 100 / 1000 Mb/s

Capacidade semi/full-duplex

Suporte para áudio de alta definição

ALC662

Saída de áudio de 5.1 canais

Suporta a especificação High-Definition Audio

ALC662

Saída de áudio de 5.1 canais

Suporta a especificação High-Definition Audio

Ranhuras

Ranhura PCI Express Gen2 x16

Ranhura PCI Express Gen2 x 1

Ranhura PCI x2 x2 x2

Ranhura PCI Express Gen2 x16

Ranhura PCI Express Gen2 x 1

Ranhura PCI x2 x2 x2

54

TA870U3+

Conector SATA

Conector do painel frontal x6 x1

Conector de áudio frontal

Conector de saída S/PDIF x1 x1

Conector da ventoinha da CPU x1

Conector da ventoinha do sistema x2

Conectores na placa

Conector para limpeza do CMOS x1

Conector USB 2.0 x3

Conector de alimentação

(24 pinos) x1 x1 Conector de alimentação

(4 pinos)

Conector de IR do consumidor

Conector da para impressora x1 x1

Entradas/S aídas no painel traseiro

Teclado PS/2

Rato PS/2

Porta série

Porta LAN

Porta USB 2.0 (por SB850)

Porta USB 3.0 (por ASM1042)

Tomada de áudio x1 x1 x1 x1 x2 x2 x3

Tamanho da placa

Característi cas especiais

220 mm (L) X 305 mm (A)

Suporta as funções RAID 0 / 1 / 10 / 5

Sistemas operativos


A Biostar reserva-se o direito de adicionar ou suportados remover suporte para qualquer sistema operativo com ou sem aviso prévio.

TA870B

Conector SATA

Conector do painel frontal x6 x1

Conector de áudio frontal

Conector de saída S/PDIF x1 x1

Conector da ventoinha da CPU x1

Conector da ventoinha do sistema x2

Conector para limpeza do CMOS x1

Conector USB 2.0 x3

Conector de alimentação

(24 pinos) x1 x1 Conector de alimentação

(4 pinos)

Conector de IR do consumidor

Conector da para impressora x1 x1

Teclado PS/2

Rato PS/2

Porta série

Porta LAN

Porta USB 2.0

Tomada de áudio

TA870U3+/TA870B

220 mm (L) X 305 mm (A) x1 x1 x1 x1 x4 x3

Suporta as funções RAID 0 / 1 / 10 / 5


A Biostar reserva-se o direito de adicionar ou remover suporte para qualquer sistema operativo com ou sem aviso prévio.

55


P

OLISH

Procesor

FSB

Chipset

TA870U3+

Socket AM3

AMD Phenom II/Athlon II/Sempron Procesory

Architektura AMD 64 umożliwia przetwarzanie

32 i 64 bitowe

Obsługa Hyper Transport 3.0 oraz Cool’n’Quiet

(Maksymalny Watt: 140W)

TA870B

Socket AM3

AMD Phenom II/Athlon II/Sempron Procesory

Architektura AMD 64 umożliwia przetwarzanie

32 i 64 bitowe

Obsługa Hyper Transport 3.0 oraz Cool’n’Quiet

(Maksymalny Watt: 140W)

Obsługa HyperTransport 3.0 o szerokości pasma Obsługa HyperTransport 3.0 o szerokości pasma do 5.2 GT/s do 5.2 GT/s

AMD 870

AMD SB850

AMD 870

AMD SB850

Pamięć główna

Super I/O

SATA 3

LAN

Obsługa audio HD

Gniazda

Gniazda DDR3 DIMM x 4

Maks. wielkość pamięci 16GB

Każde gniazdo DIMM obsługuje moduły 512MB oraz 1GB/2GB/4GB DDR3

Moduł pamięci DDR3 z trybem podwójnego

Gniazda DDR3 DIMM x 4

Maks. wielkość pamięci 16GB

Każde gniazdo DIMM obsługuje moduły 512MB oraz 1GB/2GB/4GB DDR3

Moduł pamięci DDR3 z trybem podwójnego kanału

Obsługa DDR3 800 / 1066 / 1333

Obsługa DDR3 1600 (OC)

Brak obsługi Registered DIMM oraz ECC DIMM

ITE 8728 kanału

Obsługa DDR3 800 / 1066 / 1333

Obsługa DDR3 1600 (OC)

Brak obsługi Registered DIMM oraz ECC DIMM

ITE 8728

Zapewnia najbardziej powszechne funkcje Super Zapewnia najbardziej powszechne funkcje Super

I/O. I/O.

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Monitor H/W

Funkcja ITE "Smart Guardian"

Zintegrowany kontroler Serial ATA

Transfer danych do 6 Gb/s.

Zgodność ze specyfikacją SATA w wersji 3.0.

Realtek RTL 8111E

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Monitor H/W

Funkcja ITE "Smart Guardian"

Zintegrowany kontroler Serial ATA

Transfer danych do 6 Gb/s.

Zgodność ze specyfikacją SATA w wersji 3.0.

Realtek RTL 8111E

110 / 100 / 1000 Mb/s z automatyczną negocjacją szybkości

Działanie w trybie połowicznego / pełnego dupleksu

ALC662

5.1 kanałowe wyjście audio

Obsługa High-Definition Audio

110 / 100 / 1000 Mb/s z automatyczną negocjacją szybkości

Działanie w trybie połowicznego / pełnego dupleksu

ALC662

5.1 kanałowe wyjście audio

Obsługa High-Definition Audio

Gniazdo PCI Express Gen2 x16

Gniazdo PCI Express Gen2 x 1

Gniazdo PCI x2 x2 x2

Gniazdo PCI Express Gen2 x16

Gniazdo PCI Express Gen2 x 1

Gniazdo PCI x2 x2 x2

56

TA870U3+/TA870B

TA870U3+ TA870B

Złącze SATA

Złącze panela przedniego

Przednie złącze audio

Złącze wyjścia S/PDIF x6 x1 x1 x1

Złącze SATA

Złącze panela przedniego

Przednie złącze audio

Złącze wyjścia S/PDIF x6 x1 x1 x1

Złącza

Złącze główkowe wentylatora procesora x1 wbudowane Złącze główkowe kasowania CMOS x1

Złącze USB 2.0 x3

Złącze główkowe wentylatora procesora x1

Złącze główkowe wentylatora systemowego x2 Złącze główkowe wentylatora systemowego x2

Złącze główkowe kasowania CMOS x1

Złącze USB 2.0 x3

Back Panel

I/O

Złącze zasilania (24 pinowe)


Złącze Konsument IR

Złącze Port drukarki

Klawiatura PS/2

Mysz PS/2

Port szeregowy

Port LAN

Port USB 2.0 (przez SB850)

Port USB 3.0 (przez ASM1042)

Gniazdo audio x1 x1 x1 x1 x1 x1 x1 x1 x2 x2 x3



Złącze Konsument IR

Złącze Port drukarki

Klawiatura PS/2

Mysz PS/2

Port szeregowy

Port LAN

Port USB 2.0

Gniazdo audio x1 x1 x1 x1 x1 x1 x1 x1 x4 x3

Wymiary płyty

Funkcje specjalne

220 mm (S) X 305 mm (W)

Obsługa RAID 0 / 1 / 10 / 5

220 mm (S) X 305 mm (W)

Obsługa RAID 0 / 1 / 10 / 5

Obsluga systemu operacyjne go


Biostar zastrzega sobie prawo dodawania lub odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia.


Biostar zastrzega sobie prawo dodawania lub odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia.

57


R

USSIAN

TA870U3+

Гнездо AM3

Процессоры AMD Phenom II/Athlon

Гнездо AM3

TA870B

Процессоры AMD Phenom II/Athlon

CPU

(центральный процессор)

II/Sempron

Архитектура AMD 64 разрешать обработка данных на 32 и 64 бит

II/Sempron

Архитектура AMD 64 разрешать обработка данных на 32 и 64 бит

Поддержка Hyper Transport 3.0 и Cool’n’Quiet Поддержка Hyper Transport 3.0 и Cool’n’Quiet

FSB

(Максимальный ватт: 140W)

Поддержка HyperTransport 3.0 с пропускной способностью до 5.2 GT/s

(Максимальный ватт: 140W)

Поддержка HyperTransport 3.0 с пропускной способностью до 5.2 GT/s

Набор микросхем

Основная память

Super I/O

SATA 3

Локальная сеть

AMD 870

AMD SB850

AMD 870

AMD SB850

Слоты DDR3 DIMM x 4

Максимальная ёмкость памяти 16 ГБ

Каждый модуль DIMM поддерживает 512МБ

Слоты DDR3 DIMM x 4

Максимальная ёмкость памяти 16 ГБ

Каждый модуль DIMM поддерживает 512МБ

& 1ГБ/2ГБ/4ГБ DDR3

Модуль памяти с двухканальным режимом

DDR3

Поддержка DDR3 800 / 1066 / 1333

Поддержка DDR3 1600 (OC)

Не поддерживает зарегистрированные модули DIMM and ECC DIMM

ITE 8728

& 1ГБ/2ГБ/4ГБ DDR3

Модуль памяти с двухканальным режимом

DDR3

Поддержка DDR3 800 / 1066 / 1333

Поддержка DDR3 1600 (OC)

Не поддерживает зарегистрированные модули DIMM and ECC DIMM

ITE 8728

Обеспечивает наиболее используемые действующие функциональные возможности Super I/O.

Интерфейс с низким количеством выводов

Инициативы по охране окружающей среды,

Аппаратный монитор

Функция ITE "Smart Guardian"

(Интеллектуальная защита)

Обеспечивает наиболее используемые действующие функциональные возможности Super I/O.

Интерфейс с низким количеством выводов

Инициативы по охране окружающей среды,

Аппаратный монитор

Функция ITE "Smart Guardian"

(Интеллектуальная защита)

Встроенное последовательное устройство управления ATA скорость передачи данных до 6 гигабит/с.

Соответствие спецификации SATA версия

Встроенное последовательное устройство управления ATA скорость передачи данных до 6 гигабит/с.

Соответствие спецификации SATA версия

3.0.

Realtek RTL 8111E

3.0.

Realtek RTL 8111E

Автоматическое согласование 10 / 100 / Автоматическое согласование 10 / 100 /

1000 Мб/с 1000 Мб/с

Частичная / полная дуплексная способность Частичная / полная дуплексная способность

Звуковая поддержка жесткого диска

ALC662

Звуковая поддержка High-Definition

5.1канальный звуковой выход

ALC662

Звуковая поддержка High-Definition

5.1канальный звуковой выход

Слоты

Слот PCI Express Gen2 x16

Слот PCI Express Gen2 x 1

Слот PCI x2 x2 x2

Слот PCI Express Gen2 x16

Слот PCI Express Gen2 x 1

Слот PCI x2 x2 x2

58

TA870U3+/TA870B

TA870U3+ TA870B

Разъём SATA x6 Разъём SATA x6

Разъём на лицевой панели x1 Разъём на лицевой панели x1

Входной звуковой разъём x1 Входной звуковой разъём x1

Разъём вывода для S/PDIF

Контактирующее приспособление x1 вентилятора центрального

Разъём вывода для S/PDIF

Контактирующее приспособление вентилятора центрального x1

Контактирующее приспособление

Встроенный разъём

Контактирующее приспособление

Открытое контактирующее приспособление CMOS x1

Открытое контактирующее приспособление CMOS x1

Разъем питания (24 вывод) x1 Разъем питания (24 вывод) x1

Разъем питания (4 вывод) x1 Разъем питания (4 вывод) x1

Разъём Порт подключения Разъём Порт подключения

Клавиатура PS/2

Мышь PS/2

Задняя панель средств

Порт LAN

USB 2.0-порт (по SB850) ввода-вывода USB 3.0-порт (по ASM1042)

Гнездо для подключения x1 x1 x1 x2 x2

Клавиатура PS/2 x1 x1

Порт LAN x1

USB 2.0-порт x4

Гнездо для подключения

Размер панели

Специальные технические характеристи ки

Поддержка RAID 0 / 1 / 10 / 5

Поддержка

OS

Поддержка RAID 0 / 1 / 10 / 5


Biostar сохраняет за собой право добавлять


Biostar сохраняет за собой право добавлять или удалять средства обеспечения для OS с или без предварительного уведомления. или удалять средства обеспечения для OS с или без предварительного уведомления.

59


A

RABIC

TA870B TA870U3+

ﺲﺒﻘﻣA ﺲﺒﻘﻣ AM3

تﺎﺠﻟﺎﻌﻣAMD Phenom II/Athlon II/Sempron

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺖﺏ 64 و 32 ﺔﻋﺮﺴﺏ ﺔﻴﺏﻮﺳﺎﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺝإ

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyper Transport 3.0

و Cool’n’Quiet

(طاو ىﻮ ﺼﻗ: 140و)

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyperTransport 3.0

ﻰﻟإ ﻞﺼی ددﺮﺘﺏ 5.2 GT/s

AMD 870

AMD SB850

ITE 8728

ﺔﻔﻴﻇو ﺮﻓﻮﺗSuper I/O ًﺎﻣاﺪﺨﺘﺳا ﺮﺜآﻷا

ﺔﻴﻨﻘﺗ ﻢﻋﺪ ﺗ Low Pin Count Interface

: ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو

ﺲﺒﻘﻣAM3

تﺎﺠﻟﺎﻌﻣAMD Phenom II/Athlon II/Sempron

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺖﺏ 64 و 32 ﺔﻋﺮﺴﺏ ﺔﻴﺏﻮﺳﺎﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺝإ

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyper Transport 3.0

و Cool’n’Quiet

(طاو ىﻮ ﺼﻗ: 140و)

ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺡو

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyperTransport 3.0

ﻰﻟإ ﻞﺼی ددﺮﺘﺏ 5.2 GT/s ﻲﺒﻥﺎﺠﻟا ﻲﻣﺎﻣﻷا ﻞﻗﺎﻨﻟا

AMD 870

AMD SB850

ITE 8728

ﺔﻔﻴﻇو ﺮﻓﻮﺗSuper I/O ًﺎﻣاﺪﺨﺘﺳا ﺮﺜآﻷا

ﺢﺋاﺮﺸﻟا ﺔﻋﻮﻤﺠﻣ

ﺔﻴﻨﻘﺗ ﻢﻋﺪ ﺗ Low Pin Count Interface

: ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو

ةﺰﻬﺝﻷا ﺔﻟﺎﺡ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻣ ةﺰﻬﺝﻷا ﺔﻟﺎﺡ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻣ

ﺔﻔﻴﻇو"Smart Guardian" ﻦﻣ ITE ﺔﻔﻴﻇو"Smart Guardian" ﻦﻣ ITE

4 دﺪﻋ DDR3 DIMM ﺔﺤﺘﻓ

ﺖیﺎﺏ ﺎﺠﻴﺝ 16 ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ

4 دﺪﻋ DDR3 DIMM ﺔﺤﺘﻓ

ﺖیﺎﺏ ﺎﺠﻴﺝ 16 ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻣ ةﺮآاذ ﻢﻋﺪﺗ DDR3 ﺔﻌﺳ 512 ﺖیﺎﺏ ﺎﺠﻴﻣ

ﺖیﺎﺏ ﺎﺠﻴﺝ 4 و / 2 و / 1 و

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻣ ةﺮآاذ ﻢﻋﺪﺗ DDR3 ﺔﻌﺳ 512 ﺖیﺎﺏ ﺎﺠﻴﻣ

ﺖیﺎﺏ ﺎﺠﻴﺝ 4 و / 2 و / 1 و

ةﺮآاذ ةﺪﺡوDDR3 ةﺎﻨ ﻘﻟا ﺔﺝودﺰﻣ

عﻮﻥ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 ﺖیﺎﺏ ﺎﺠﻴﻣ 1333 / 1066 / 800 تﺎﻌﺳ عﻮﻥ ﻦ ﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗ DDR3 ﺖیﺎﺏ ﺎﺠﻴﻣ 1333 / 1066 / 800 تﺎﻌﺳ

عﻮﻥ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 ﺖیﺎﺏ ﺎﺠﻴﻣ ( OC ) 1600 تﺎﻌﺳ

ةﺮآاذ ةﺪﺡوDDR3 ةﺎﻨ ﻘﻟا ﺔﺝودﺰﻣ

عﻮﻥ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 ﺖیﺎﺏ ﺎﺠﻴﻣ ( OC ) 1600 تﺎﻌﺳ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻣ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻣ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC

Super I/O

ﺔﻴﺴﻴﺋﺮﻟا ةﺮآاﺬﻟا

ﻞﻣﺎﻜﺘﻣ

ﻰﻟإ ﻞﺼﺗ تﺎﻋﺮﺴﺏ تﺎﻥﺎﻴﺒﻟا ﻞﻘﻥ 6 .

ﺔﻴﻥﺎﺙ / ﺖﺏﺎﺠﻴﺝ

ﺔﻘﺏﺎﻄﻣ راﺪﺹﻹا 3.0.

Realtek RTL 8111E

ﺔﻴﻥﺎﺙ / ﺖﺏ ﺎﺠﻴﺝ 1 و ﺔﻴﻥﺎﺙ / ﺖیﺎﺏ ﺎﺠﻴﻣ 100 / 10 ﻲﺋﺎﻘﻠﺗ ضوﺎﻔﺗ

ﻞﻣﺎﻜﺘﻣ

ﻰﻟإ ﻞﺼﺗ تﺎﻋﺮﺴﺏ تﺎﻥﺎﻴﺒﻟا ﻞﻘﻥ 6 .

ﺔﻴﻥﺎﺙ / ﺖﺏﺎﺠﻴﺝ SATA 3

ﺔﻘﺏﺎﻄﻣ راﺪﺹﻹا 3.0.

Realtek RTL 8111E

ﺔﻴﻥﺎﺙ / ﺖﺏ ﺎﺠﻴﺝ 1 و ﺔﻴﻥﺎﺙ / ﺖیﺎﺏ ﺎﺠﻴﻣ 100 / 10 ﻲﺋﺎﻘﻠﺗ ضوﺎﻔﺗ ﺔﻴﻠﺥاد ﺔﻜﺒﺵ

ﻲﻔﺼﻨﻟا / ﻞﻣﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻣإ

ALC662

5.1

تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

ﻦﻣ ﻒیﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

ﻲﻔﺼﻨﻟا / ﻞﻣﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻣإ

5.1

تﻮﺼﻟا

ALC662

جﺮﺨﻟ تاﻮﻨﻗ

ﻦﻣ ﻒیﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

ﻲﻟﺎﻋ تﻮﺼﻟا ﻢﻋد

ﻒیﺮﻌﺘﻟا

2 دﺪﻋ PCI Express Gen2 x16 ﺔﺤﺘﻓ 2 دﺪﻋ PCI Express Gen2 x16 ﺔﺤﺘﻓ

2 دﺪﻋ

2 دﺪﻋ

PCI Express Gen2 x 1 ﺔﺤﺘﻓ

PCI ﺔﺤﺘﻓ

2 دﺪﻋ

2 دﺪﻋ

PCI Express Gen2 x 1 ﺔﺤﺘﻓ

PCI ﺔﺤﺘﻓ

تﺎﺤﺘﻔﻟا

60

TA870B

6

1

1

1

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

SATA ﺬﻔﻨﻣ

ﺔﻴﻣﺎﻣﻷا ﺔﺡﻮﻠﻟا ﺬﻔﻨﻣ

ﻲﻣﺎﻣﻷا تﻮﺼﻟا ﺬﻔﻨﻣ

S/PDIF جﺮﺥ ﺬﻔﻨﻣ

1 دﺪﻋ ﺔیﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺡو ﺔﺡوﺮﻣ ﺔﻠﺹو

2 دﺪﻋ مﺎﻈﻨﻟا ﺔﺡوﺮﻣ ﺔﻠﺹو

1 دﺪﻋ

3 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

(

CMOS

سﻮﺏد 24

(

)

ﺢﺴﻣ ﺔﻠﺹو

USB 2.0

ﺬﻔﻨﻣ

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ

سﻮﺏد 4 ) ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ

ﺔﻜﻠﻬﺘ ﺴﻣ ﺖ ﺤﺗ ﺮﻤﺡﻷا ﺬﻔﻨﻣ

ﺔﻌﺏﺎﻃ ﺬﻔﻨﻣ

TA870U3+

TA870U3+/TA870B

6

1

1

1

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

SATA ﺬﻔﻨﻣ

ﺔﻴﻣﺎﻣﻷ ا ﺔﺡﻮﻠﻟا ﺬﻔﻨﻣ

ﻲﻣﺎﻣﻷا تﻮﺼﻟا ﺬﻔﻨﻣ

S/PDIF جﺮﺥ ﺬﻔﻨﻣ

1 دﺪﻋ ﺔیﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺡو ﺔﺡوﺮﻣ ﺔﻠﺹو

2 دﺪﻋ مﺎﻈﻨﻟا ﺔﺡوﺮﻣ ﺔﻠﺹو

1

3

1

1

1

1

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

دﺪﻋ

CMOS ﺢﺴﻣ ﺔﻠﺹو

USB 2.0

ﺬﻔﻨﻣ

( سﻮﺏد 24 ) ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ

( سﻮﺏد 4 ) ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ

ﺔﻜﻠﻬﺘ ﺴﻣ ﺖ ﺤﺗ ﺮﻤﺡﻷا ﺬﻔﻨﻣ

ﺔﻌﺏﺎﻃ ﺬﻔﻨﻣ

ﺢﻄﺳ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟا

ﺔﺡﻮﻠﻟا

1 دﺪﻋ PS/2 ﺢﻴﺗﺎﻔﻣ ﺔﺡﻮﻟ

1 دﺪﻋ PS/2 ﺢﻴﺗﺎﻔﻣ ﺔﺡﻮﻟ

1 دﺪﻋ PS/2 سوﺎﻣ

1 دﺪﻋ PS/2 سوﺎﻣ

1 دﺪﻋ ﻲﻠﺴﻠﺴﺗ ﺬﻔﻨﻣ

1 دﺪﻋ ﻲﻠﺴﻠﺴﺗ ﺬﻔﻨﻣ

1 دﺪﻋ ﺔﻴﻠﺤﻣ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻣ

جﺮﺥ / ﻞﺥد ﺬﻓﺎﻨﻣ

ﺔﻴﻔﻠﺨﻟا ﺔﺡﻮﻠﻟا

1 دﺪﻋ ﺔﻴﻠﺤﻣ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻣ

4 دﺪﻋ

3 دﺪﻋ

2 دﺪﻋ (SB850 ﻦﻣ ﻞ ﺒﻗ ) USB 2.0

ﺬﻓﺎﻨﻣ

2.0

USB ﺬﻓﺎﻨﻣ

تﻮﺹ ﺲﺒﻘﻣ

( عﺎﻔﺗرا ) ﻢﻣ 305 X ( ضﺮﻋ ) ﻢﻣ 220

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗRAID 0 / 1 / 10 / 5


ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺥﺈﺏ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺏ

.

رﺎﻄﺥإ نوﺪﺏ

2 دﺪﻋ (ASM1042 ﻦﻣ ﻞ ﺒﻗ ) U SB3.0

ﺬﻓﺎﻨﻣ

3 دﺪﻋ تﻮﺹ ﺲﺒﻘﻣ

ﺔﺡﻮﻠﻟا ﻢﺠﺡ

ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗRAID 0 / 1 / 10 / 5


ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺥﺈﺏ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺏ

.

رﺎﻄﺥإ نوﺪﺏ

ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻥأ ﻢﻋد

61


J

APANESE

CPU

FSB

チップセット

Socket AM3

AMD Phenom II/Athlon II/Sempron プロセッサ

Socket AM3

AMD Phenom II/Athlon II/Sempron プロセッサ

AMD 64アーキテクチャでは、32ビットと64ビット計 AMD 64アーキテクチャでは、32ビットと64ビット計

算が可能です

ハイパートランスポート

3.0とクールアンドクワイア

算が可能です

ハイパートランスポート

3.0とクールアンドクワイア

をサポートします

AMD 870

AMD SB850

TA870U3+

ットをサポートします

(最高のワット: 140W)

5.2 GT/sのバンド幅までハイパートランスポート3.0

DDR3 DIMMスロット x 4

最大メモリ容量 16GB

各 DIMMは 512MB & 1GB/2GB/4GB DDR3をサポ

メインメモリ

ート

デュアルチャンネルモードDDR3メモリモジュール

DDR3 800 / 1066 / 1333 をサポート

DDR3 1600 (OC) をサポート

登録済み

DIMMとECC DIMMはサポートされません

ットをサポートします

(最高のワット: 140W)

5.2 GT/sのバンド幅までハイパートランスポート3.0

をサポートします

AMD 870

AMD SB850

TA870B

DDR3 DIMMスロット x 4

最大メモリ容量

各

16GB

DIMMは 512MB & 1GB/2GB/4GB DDR3をサポ

ート

デュアルチャンネルモードDDR3メモリモジュール

DDR3 800 / 1066 / 1333 をサポート

DDR3 1600 (OC) をサポート

登録済み

DIMMとECC DIMMはサポートされません

Super I/O

スロット

ITE 8728

もっとも一般に使用されるレガシー

Super I/O機能を

採用しています。

低ピンカウントインターフェイス

環境コントロールイニシアチブ、

H/Wモニター

SATA 3

ITEの「スマートガーディアン」機能

統合シリアル

ATAコントローラ

最高 6Gb/秒のデータ転送速度

SATAバージョン3.0仕様に準拠。

Realtek RTL 8111E

LAN 10 / 100 / 1000 Mb/秒のオートネゴシエーション

半 /全二重機能

HDオーディ

ALC662

オのサポート

5.1チャンネルオーディオアウト

ハイデフィニションオーディオのサポート

PCI Express Gen2 x16スロット

PCI Express Gen2 x1スロット x2 x2

ITE 8728

もっとも一般に使用されるレガシー

Super I/O機能を

採用しています。

低ピンカウントインターフェイス

環境コントロールイニシアチブ、

H/Wモニター

ITEの「スマートガーディアン」機能

統合シリアル

ATAコントローラ

最高 6Gb/秒のデータ転送速度

SATAバージョン3.0仕様に準拠。

Realtek RTL 8111E

10 / 100 / 1000 Mb/秒のオートネゴシエーション

半 /全二重機能

ALC662

5.1チャンネルオーディオアウト

ハイデフィニションオーディオのサポート

PCI Express Gen2 x16スロット x2

PCI Express Gen2 x1スロット x2

62

TA870U3+

TA870U3+/TA870B

TA870B

フロントパネルコネクタ x1 x1

フロントオーディオコネクタ x1 フロントオーディオコネクタ x1

S/PDIFアウトコネクタ x1 S/PDIFアウトコネクタ x1

オンボードコシステムファンヘッダ x2 x2

ネクタ

背面パネル

I/O

ボードサイズ

特殊機能

電源コネクタ (24ピン)

電源コネクタ (4ピン) x1 x1

電源コネクタ

電源コネクタ

(24ピン)

(4ピン) x1 x1

消費者 IRコネクタ x1

プリンタポートコネクタ

x1 x1

PS/2キーボード x1

PS/2キーボード

PS/2マウス

シリアルポート x1

x1 x1 x1

シリアルポート

x1

LANポート x1

USB 2.0ポート(で SB850) x2

USB 2.0ポート x4

USB 3.0ポート (で ASM1042)

オーディオジャック x2

オーディオジャック

x3

x3

220 mm (幅) X 305 mm (高さ)

RAID 0 / 1 / 10 / 5 のサポート

OSサポート


Biostarは事前のサポートなしにOSサポートを追加ま

たは削除する権利を留保します。

220 mm (幅) X 305 mm (高さ)

RAID 0 / 1 / 10 / 5 のサポート


Biostarは事前のサポートなしにOSサポートを追加ま

たは削除する権利を留保します。

2010/12/06

63

No results