USER MANUAL DG 2202 E

Add to my manuals
20 Pages

advertisement

USER MANUAL DG 2202 E | Manualzz

October 7, 1999 1

USER MANUAL

DG 2202 E

TEGN. 1:10 980108/JOA 6227-OOB

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 2

NOTICE

All statements technical information and recommendations contained herein are based on tests we believe to be reliable, but accuracy of completeness thereof is not guarantied and the following is made in lieu of all warranties, expressed or implied:

Danagraf A/S shall not be liable or responsible to any purchaser or other person for injury, loss or damage neither direct, incidental or consequential, due to the use of or inability to the Danagraf equipment information in this manual.

Before using, user shall determine the suitability of the product for his intended use, and user assumes all risks and liability, whatsoever in connection therewith.

The processor is, to the best of our knowledge, suitable to work with all types of chemistries known to the graphic marked.

No statement or recommendation not contained herein, shall have any force or effect in any agreement signed by officers of sellers and manufacturer.

Sincerely Yours,

DANAGRAF A/S

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 3

TABLE OF CONTENTS

NOTICE …………………………………………………………………………

TABLE OF CONTENTS ………………………………………………………

INTRODUCTION ………………………………………………………………

TECHNICAL DATA ……………………………………………………………

GENERAL DESCRIPTION …………………………………………………..

CONTROL PANEL …………………………………………………………...

PREPARATIONS ……………………………………………………………..

DEVELOPING …………………………………………………………………

MAINTENANCE ……………………………………………………………….

Routine cleaning ………………………………………………………...

Every day ………………………………………………………………...

Every week ……………………………………………………………….

Occasionally ……………………………………………………………..

GENERAL QUALIY CONTROL STATEMENT …………………………….

TROUBLESHOOTING GUIDE ………………………………………………

FILM QUALITY HINTS AND TROUBLE SHOOTING …………………….

Page 2

Page 3

Page 4

Page 5

Page 7

Page 9

Page 11

Page 13

Page 15

Page 15

Page 15

Page 15

Page 15

Page 16

Page 17+18

Page 19

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 4

INTRODUCTION

The Danagraf DG 2202E Film Processor is conceived to accommodate the smaller user with the technology and ease of operation of automatic processing .

The high quality of Danagraf s renown processor line is also applied in this simplified, though complete production unit. All processor functions such as developer and fixer temperature and processing speed are controlled by means of a small handy operator panel. The holder for the control panel can be installed on the standard feed table or the daylight cassette left or right. If by accident the developer gets into the. wall, it can be drained below the front of the processor, see drawing below.

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 5

TECHNICAL DATA

DG 1802F

Height Total

Height Processor

Height Stand

Height Daylight cassette

Width

Length

Net weight

Power supply

Max. power consumption

Min. developing time

Factory setting developer time

Max. Developing time

Min. film length

Min. film width

Max. film width

Tank capacity

Developer

Fixer

Water

1265 m.m. / 49.8"

360 m.m. / 14.2"

655 m.m. / 25.8"

313 m.m. / 12.3"

758 m.m. / 29.8"

1325 m.m. / 33.65"

67 kg / 147.7 lbs.

230V 50/6OHz

2700 W

25 sec.

35 sec.

60 sec.

140 m.m. / 5.5"

30 m.m. / 1.2"

550 m.m. / 21.65"

10 Itr / 2.6 U.S. Gallon

10 Itr / 2.6 U.S. Gallon

10 Itr / 2.6 U.S. Gallon

5 User Program

Adjustable temp. Developer

Factory setting developer

Adjustable temp. fixer

Factory setting fixer

Adjustable automatic dev. Replenish

Factory setting dev. Replenish

Adjustable automatic fix. replenish

Factory setting fix. Replenish

Adjustable dryer temperature

Factory setting dryer temperature

15 - 45

0

C / 59 - 113

0

F

33

0

C

15 - 45

0

C / 59 - 113

0

F

30

0

C

0 - 999 ml / m

2

400 ml / m

2

0 - 999 ml / m

2

300 ml / m

2

20 - 60

0

C / 68 -140

0

F

45

0

C / 113

0

F

Anti-oxidation program, fixed

Anti-oxidation dev. Adjustable

Anti-oxidation fix. Adjustable

60 min.

15 - 75 ml / hrs.

15 - 75 ml / hrs.

Room conditions: Temperature 20 - 25

0

C / 68 - 77

0

F, humidity 45 – 85%

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 6

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 7

GENERAL DISCRIPTION

When turning power ON the TEMP display ( x x ) will show the type of machine and the

SPEED display ( x x x ) will show the E-Prom version for 5 sec.

When turning ON the main power, the rollers and pumps will run for a short while, this is for refreshment of the chemistry and to avoiding crystallization on the top rollers.

As long as the processor is turned ON, the fan on the fight hand side will be ON. This will prevent condensation and removes fumes from the processor.

The temperature for Developer, Fixer are adjustable and so is the process speed.

Whenever you enter material, and tile machine, is ready, tile processor will go to operating mode.

The amount of replensihment of developer and Fixer is automatically calculated to maintain a correct level and balance of the chemistry.

In case of "Low level" in any of the tanks, you will hear an acoustic ala and a red diode on the Control Panel will go ON. The processor will set the respective replenish-pump ON in order to keep the correct level. If the replenish-pump is active for more than 40 sec the pump will stop and Dev or Fix level warning will light up.

If low level occur in one of the baths, the belonging circulation pump and heater will not be able to work.

You have the possible to control the replenish pumps manually by pressing the respective buttons.

When the film affect the inlet sensor the processor starts and the Speed Display will flash with fast speed as long as the film affect the inlet sensor ( " NO further INPUT " )

(processor busy). When the trailing edge of the film pass the inlet sensor the Speed

Display will return to steady display, and the next film can be introduced.

After the film leaves the dryer, the processor will go to a " stand by " mode.

If the processor has not been used for one hour, the " ANTI-OXIDATION " program will go active, which will cause the roller to turn for 14 sec. to avoid crystallization. Replenish pump will give amount of replenish. See page 9 chapter for control Panel.

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 8

CONTROL PANEL

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 9

CONTROL PANEL

The DG 2202E have 5 User Programs.

The TEMP. display will show the actual temperature of the developer. to check the temp.

for fixer, just press [ 1 ] key to change between DEV and FIX temperature.

1,0 Setting Program

Press key [ 4 ]+[ 5 ] PROG. ON for 1 sec.

The display for TEMP. will go OFF and the Program 01 - 05 selected by pressing key [ 4 ] or [ 5 ] will be shown in the SPEED display.

2,0 Speed Change

Press key [ 1 ] until Temp Display shows (II).

The SPEED can be changed with [ ^ ] and [ v ] key.

3,0 Developer Temperature Setting

Press key [ 1 ] until Temp Display shows (-1).

The temperature can be changed with [ ^ ] or [ v ] key.

4,0 Fixer Temperature Setting

Press key [ 1 ] until Temp Display shows (-2).

The temperature can be changed with the [ ^ ] or [ v ] key.

5,0 Dryer Temperature Setting

Press key [ 1 ] until Temp Display shows (-3).

The dryer temperature can be changed with [ ^ ] or [ v ] key.

6,0 Developer Replenish Setting

Press key [ 1 ] until Temp Display shows (U1) ( 05-99 ) is 50 - 999 ml/m

2

, can be changed with the [ ^ ] or [ v ] key.

7,0 Developer Replenish Setting

Press key [ 1 ] until Temp Display shows (U2) ( 05-99 ) is 50 - 999 ml/m

2

, can be changed with the [ ^ ] or [ v ] key.

8,0 Anti-oxidation Developer

Press key [ 1 ] until Temp Display shows (A1) adjust amount between 15 - 75ml pr. hour, with [ ^ ] or [ v ] key.

9,0 Anti-oxidation Fixer

Press key [ 1 ] until Temp Display shows (A2) adjust amount between 15 - 75ml pr. hour, with [ ^ ] or [ v ] key.

All new value will be saved in the E-Prom. To exit press at the same time key [ 2 ] + [ 3 ]

(Program OFF) for one sec.

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 10

(THIS PAGE IS NOT IN USE)

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 11

PREPARATIONS

After the processor has been installed by a qualified technician, you can prepare to fill up the tanks with chemistry.

NOTE: Always follow the instructions given by the film and chemistry manufacturer.

Fixer:

It is strongly recommended first to fill-up the fixer tank in order to prevent splashing into the developer section. This will cause contamination of the developer and result in a poor developing process. The fixer tank is marked with blue.

Developer:

Before filling the developer into the Dev. tank, check and make sure that no splashing has occurred, when filling the fixer tank. If so clean thoroughly. The developer tank is marked with red.

Replenishment:

Mix some additional Developer and Fixer in separate containers. Place these under the processor and insert the 1/2" red hose into the Developer and the 1/2" it blue hose into the

Fixer container.

Turn the processor "ON" and set up the programs, according to your needs.

Press the "MAN. REP. DEV." and "MAN. REP. FIX." buttons for a few seconds to make sure chemistry is pumped up through the system in order to remove air pockets.

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 12

(THIS PAGE IS NOT IN USE)

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 13

DEVELOPING

When you insert film through the entrance slot a switch will be activated. The processor will start up in process mode. After the trailing edge has left the infeed sensor the processor will still run in process mode until material has completely left the dryer section.

When the processor is in the "STAND BY" mode the Anti-oxidation program will be active.

This means the rollers will turn for 14 sec. every 60 min. to avoid crystallisation on the rollers. At the same time the Anti-oxidation program will maintain the balance of the chemistry according to the settings.

Note: It is not possible to change the developing time (SPEED) during process mode.

DG 2202E

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 14

(THIS PAGE IS NOT IN USE)

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 15

RECOMMENDED MAINTENANCE

Routine cleaning:

The most effective way to avoid operating difficulties is to regularly clean the processor, its hoses and the replenishment pumps.

Chemistry is subject to oxidisation and even though the machine has its own program to eliminate this problem, the operator should pay special attention to preserve the chemistry and remove crystallised deposits from the equipment.

The use of floating lid in the developer replenish container will keep out the air to preserve the chemistry. This will give better results and create fewer problems.

The following suggestions are simple but extremely necessary. They will help enormously to avoid spoiled work, wasted time, lost tempers and unnecessary expense.

NOTE: Be careful, always to mount the parts in the correct position after cleaning.

Every day:

Clean the to cover, the film entry and the light room cassette (optional).

Use separate damp cloths to clean guides and each set of upper rollers.

Feed one or two film before commencing the days work.

Every week:

(in addition to above)

Turn OFF the processor and remove all 3 racks. Clean them carefully with lukewarm water, using separate cloths for each rack.

NOTE: Racks can be removed and refitted without draining out the chemicals, but once again, it is essential to make sure that not one drop of fixer goes into the developer bath. If this happens, the developer must be drained and the bath must then be thoroughly cleaned and refilled.

Every month or when needed:

(in addition to above)

Drain both baths and empty the replenishment containers.

Fill the baths and replenishment containers with water and ensure that the racks baths, hoses and containers are thoroughly washed by flushing and pumping water through each bath / system.

After refilling the bath, repeatedly press the manual replenishment buttons for the developer and fixer, to eliminate any air pockets in the system.

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 16

GENERAL QUALITY CONTROL STATEMENT

If there is a reduction in the quality of the processed materials, it can probably be solved by checking the control settings, the operational procedures, or by giving a little extra attention to the routine cleaning. A small amount of time invested in "SELF HELP" will usually avoid a lot of wasted time and possible expense which will result from calling in a service technician.

If, however, the problem seems to be electrical or mechanical do not attem t suc complex trouble shooting unless you are well qualified to do so.

Great care has been taken in the development specification, and manufacture of this equipment to ensure that it will give many years of reliable performance and quality. It should therefore be expected that "REAL" technical problems will be rare and, if encountered, will involve the chemistry and materials, or the routine cleaning.

The following pages will provide answers to the most common problems that can be encountered when processing work.

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 17

TROUBLESHOOTING GUIDE

PROBLEM

The processor is not working

The processor shows only vertical lines in display and does not work

The material jammed at the entry

The material jammed in developer, fixer or water rack.

SOLUTION

Make sure that the machine is plugged in

Check whether the fuse is working

Check that the toppled is correctly on the

Processor, switch off the Processor wait

5-10 sec. and switch on again.

Check that the material is not to curled

Check that the entry guide is in correct position

Make sure that the rollers in the developer input rack is running smoothly.

Check daylight feed slot.

Make sure that all rollers in the developer-fixer-water rack is running smoothly.

Check that the developer rack is in the correct position.

Remove the roller rack and clean it thoroughly. Ensure that the rack and its rollers are in their correct locations and the rollers are turning evenly and freely.

The material jammed at crossover between developer and fixer or between fixer and water rack.

Insure that the developer, fixer and water rack are perfectly levelled.

Check that the crossover guide is in correct position.

Ensure that the roller rack are at their correct location and that the crossover guides are correctly fitted.

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 18

The material jammed at crossover between fixer and water or water and dryer.

Insure that the fixer, water and dryer rack are perfectly levelled.

The material jammed in Dryer rack.

Check that the crossover guide is in correct position.

Ensure that the roller rack are at their correct location and the crossover guides are correctly fitted.

Make sure that the Dryer temperature is approx. 45

0

C and that excessive heat is not causing the material to curl.

No manual replenish

No heating in baths.

No circulation in baths.

Check that Dryer-rack is in correct position.

Make sure that the rollers in the Dryer-rack is running smoothly.

Check level in replenish tank. Qualified investigation necessary.

Check pre-set temperatures.

Check level in baths.

Check level in baths.

Beeper is sounded twice

Speed display is flashing

Temperature display is flashing

Temperature display is flashing and LED is lit.

Beeper is sounded, Dev. LED is On and

Speed display is flashing

Beeper is sounded, Fix LED is On and

Speed display is flashing

Film has been developed

There is film in the entrance.

Low temp in Dev

Low temp in Fix.

The level is low in the DEV. bath.

The level is low in the FIX. bath.

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 19

FILM QUALITY HINTS AND TROUBLE SHOOTING

PROBLEM

Lengthways stripes on the material

The material is scratched

The material is coming out wet

The Processor stops before the material come out

Material is sticky or milky when coming out

(for optimum drying use hardener)

Material is jamming in one of the baths

Material is jamming at the crossover

SOLUTION

Remove and clean the crossover guides.

Check that the crossover guides are fitted correctly, and clean all top rollers and crossover guide

Inspect the dryer section and make sure that the assembly is correctly

Drain the fixer bath and refill with a new chemistry solution.

Make sure that the Dryer temperature sensor bar is in correct position

Check that the Dryer rack is in correct position

Check whether there is sufficient dryer air flow.

Check the developing time is set correctly.

Insure that the input sensor has been activated during the entire length of the material.

Check that the rack are in correct position and the rollers are running smoothly.

Drain the fixer bath and refill with a new chemistry solution

Clean rollers in dryer section

Remove the roller rack and clean it thoroughly. Ensure that the rack and its rollers are in their correct locations and the rollers are turning evenly and freely.

Ensure that the roller rack are their correct location and that the cross over -,guides are correctly fitted.

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

October 7, 1999 20

DANAGRAF A/S INDUSTRIVEJ 11-13, DK-4180 SORØ. TLF: +45 57860100 FAX: +45 57860119

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF

advertisement