Emerson CF230WW00 Owner`s manual

READ AND SAVE THESE INSTRUCTIONS
VELOCE
Damp Location Ceiling Fan
Owner's Manual
Model Numbers
CF230BS00
CF230ORB00
CF230WW00
Net Weight:
Part No. F40BP74340000
17.0
Lbs.
Form No. BP7434
U.L. Model No.: CF230
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must be in accordance with the National Electrical Codes “ANSI/NFPA 70-2008” and
Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling
fan must be grounded as a precaution against possible electrical shock. Electrical installation
should be made or approved by a licensed electrician.
3. The ceiling structure must be capable of reliably supporting at least 50 pounds.
4. Use only U.L. outlet boxes listed as “Acceptable for Fan Support of 15.9 kg (35 lbs) or less”, and
use the mounting screws provided with the outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan support and may need to be replaced. Consult
a qualified electrician if in doubt.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with the fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do
not know enough about electrical wiring, have your fan installed by a licensed electrician.
CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan
before light kit.
7. Use only with light kits marked suitable for use in damp locations” to the Additional Safety
Instructions for Installation.
NOTE: All set screws must be checked and re-tightened where necessary before installation.
WARNING: To reduce the risk of fire or electrical shock, do not use this fan with any solid-state
speed control device.
WARNING: To avoid fire, shock or injury, do not use on Emerson or any other brand of control not
specifically approved fro this fan.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed
control, Model No. SR401/U.L. Model No. UC7067RAL manufactured by Rhine Electric Co., Ltd.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use with this product by Emerson Electric Co. Substitution
of parts or accessories not designated for use with this product by Emerson Electric Co. could
result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
WARNING: To reduce the risk of electric shock, this fan must be installed with an isolating wall
control/switch.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2
U.L. Model No.: CF230
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
THIS FAN IS SUITABLE FOR DAMP LOCATIONS SUCH AS COVERED PORCHES, COVERED PATIOS,
AND COVERED DECKS...ANYWHERE THERE IS A ROOF OVERHEAD.
USE ONLY WITH LIGHT KITS MARKED SUITABLE FOR USE IN DAMP LOCATIONS.
Installed Wire Length
Wire Size A.W.G.
Tools Needed for Assembly
One Phillips head screwdriver
One 1/4” blade screwdriver
Up to 50 ft.
50-100 ft.
One stepladder
One wire stripper
14
12
WARNING
!
MATERIALS
Before assembly your ceiling fan, refer to section
on proper method of wiring your fan (page 9 or 12).
If you feel you do not have enough wiring
knowledge or experience, have your fan installed
by a licensed electrician.
Wiring outlet box and box connectors must be of
type required by the local code. The minimum wire
would be a 3-conductor (2-wire with ground) of the
following size:
Unpacking Instructions
!
7. One 1/4-20 x 9/16” flange screw with lockwasher (spare)
8. Two threaded stud, #8-32 x 1-1/4”
9. Two external tooth lockwashers
10. Two knurled knobs, #8-32
11. One clevis pin
12. One hairpin clip
13. One balancing kit
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
!
WARNING
NOTE: Place the parts from the loose parts bags
in a small container to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
2. Remove the fan assembly from the protective
plastic bag. Place the fan assembly into the upper
foam pad with the lead wires up.
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
1. Open carton containing fan. Remove top half of
styrofoam unit. Remove parts and check to see
that you have received the following parts:
NOTE: If you are uncertain of part description,
refer to exploded view illustration.
a. Fan motor assembly
b. One hanger bracket
c. One 4.5” downrod assembly
d. One ceiling cover trim ring
e. One ceiling cover with trim plugs
f. One lower cover
g. One light kit plate assembly
h. One coupler cover
i. Four fan blade flanges
j. Four fan blades
k. One 50 watt GU10 base light bulb
l. RCFP-190 receiver & SR400 transmitter
m. One loose parts bag containing:
1. Three 12 ga. wire connectors
2. Thirteen #10-24 x 5/16" flange head blade screws
3. Four #10-24 x 3/16" pan head screws
4. Four #10 external tooth lockwasher
5. One rubber gasket
6. One #8-32 x 5/16” light switch screw (spare)
b.
a.
c.
d.
g.
e.
k.
h.
f.
l.
l.
i.
j.
m.
3
U.L. Model No.: CF230
Electrical Requirements
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The ceiling structure must be capable of reliably
supporting at least 50 pounds.
!
!
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
WARNING
To reduce the risk of fire, electrical shock, or
personal injury, mount fan to outlet box marked
“Acceptable for Fan Support of 15.9 kg (35 lbs) or
less", and use screws supplied with outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
!
WARNING
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
IMPORTANT: Your ceiling fan will not function
properly, and may be damaged, if used with any wall
dimmer switch or control other than the Emerson
Electric Fan/Light Remote Control supplied with the
fan.
Your Emerson ceiling fan comes supplied with a Fan
Remote Control which consists of a wall mounted
switch which allows you to regulate your ceiling fan
speed.
Installation of Hanger Bracket
IMPORTANT
Your Emerson Ceiling is designed to be installed either in the standard manner, or in the close-to-theceiling manner. Using the standard method, the hanger ball/downrod assembly will suspend the fan several
inches below the ceiling cover. Using the close-to-the-ceiling method, the ceiling cover installs directly on
the fan motor housing, thus mounting the fan 3-1/2 inches closer to the ceiling than the standard methond.
In no case should the fan blades be lower than seven feet above the floor. Depending on your desire
mounting method, proceed to ‘INSTALLING HANGER BALL/DOWNROD ASSEMBLY” for standard
mounting, or to “INSTALLING CEILING COVER ON FAN MOTOR HOUSING” for close-to-the-ceiling
mounting.
!
CEILING
WARNING
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 1).
STANDARD
INSTALLTION
!
WARNING
CLOSE-TO-THE-CEILING
INSTALLTION
AT
LEAST
7'
AT
LEAST
7'
To reduce the risk of fire, electrical shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of 15.9 kg (35 lbs) or less", and use screws
supplied with outlet box. Most outlet boxes commonly
used for support of light fixtures are not acceptable for
fan support and may need to be replaced. Consult a
qualified electrician if in doubt.
FLOOR
Figure 1
4
U.L. Model No.: CF230
Installation of Hanger Bracket
!
(continued)
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
OUTLET BOX
T-SLOT
1. Disconnect electrical power to the branch circuit at
the circuit breaker or fuse box before attempting to
install the ceiling fan mounting plate on the outlet
box.
LOOSEN TWO
SCREWS (SUPPLIED
WITH OUTLET BOX)
SLIDE THE HANGER
BRACKET ONTO
THE OUTLET BOX
SCREWS, THROUGH
THE T-SLOT
2. Loosen (but do not remove) the two mounting
screws in the outlet box (Figure 2). Position the
hanger bracket on the outlet box so that the T-slots
in the hanger bracket are aligned with the outlet
box screws.
HANGER
BRACKET
Figure 2
NOTE: The hanger bracket must be mounted
flush with the ceiling in order for the ceiling cover
to install properly. If necessary, use leveling
washers (not supplied) between the outlet box
and the hanger bracket.
3. Slide the hanger bracket onto the outlet box
screws. Center the bracket over the outlet box and
then securely tighten the screws (Figure 3).
!
SECURELY TIGHTEN
SCREWS
HOOK
HANGER BRACKET
Figure 3
WARNING
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
5
U.L. Model No.: CF230
Installation of Blades & Light Assembly
1. Mount the blade flanges to the fan blades using
three #10-24 x 5/16” Phillips blade screws per
blade (supplied) (Figure 4). Repeat for the three
remaining blades.
!
10-24 x 5/16" FLANGE
HEAD BLADE SCREW
(3 Per Blade)
FAN BLADE
WARNING
FAN BLADE
FLANGE
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
Figure 4
2. Attach one blade assembly to the motor using the
captive screw provided for each flange (Figure 5).
Make sure the screws are tightened securely.
Repeat this procedure for the other three blade
assemblies.
MOTOR
HOUSING
CAPTIVE SCREW
BLADE FLANGE
ASSEMBLY
NOTE: Take care not to scratch the fan housing
when installing the blade assemblies.
3. Remove one of the fan motor assembly screw (and
retain for later use) and loosen the two other
screws for installation of the light kit plate assembly
(Figure 6).
Figure 5
REMOVE AND RETAIN
FAN MOTOR SCREW
REMOVE AND RETAIN
WIRE CONNECTORS (2)
4. Remove and retain the wire connectors from the
white and blue wires (Figure 6).
5. Connect the white wire from the ceiling fan to the
white wire of the light kit plate (Figure 7). Connect
the blue wire from the ceiling fan to the black wire
of the light kit plate. Use wire connectors
(previously removed) to make connections.
LOOSEN TWO FAN
MOTOR SCREWS
NOTE: Carefully tuck all wires and connectors
into the fan motor assembly.
!
Figure 6
WARNING
LIGHT KIT PLATE
ASSEMBLY
To avoid possible fire or shock, make sure that
electrical wires are not pinched between the light kit
plate assembly and the fan motor assembly.
REINSTALL WIRE
CONNECTORS
LIGHT SWITCH
BLACK WIRE
LIGHT SWITCH
WHITE WIRE
FAN MOTOR
BLUE WIRE
Figure 7
6
FAN MOTOR
WHITE WIRE
U.L. Model No.: CF230
Installation of Blades & Light Assembly
5. Position the light kit plate assembly onto the fan
motor assembly, careful to not pinch any wires
during installation.
(continued)
REINSTALL FAN
MOTOR SCREW
6. Rotate the light kit plate assembly counterclockwise to engage the two key slots with the two
screws in the fan motor assembly.
7. Reattached the screw (removed in Step 3) into the
light kit plate assembly and securely tighten the
three screws (Figure 8).
RETIGHTEN TWO FAN
MOTOR SCREWS
Figure 8
NOTE: Do not engage the light bulb at this time.
NOTE: Continue to Close-to-the-Ceiling installation if needed.
How to Assemble Your Ceiling Fan
Proceed to "Close-To-The-Ceiling" section on page
11 if you are not using the downrod to hang your
ceiling fan.
PIN
NOTE: Carefully turn partially assembled ceiling fan
over and place into the packing styrofoam to
complete the assembly of your ceiling fan. Be extra
careful with the blades while turning the fan over.
HANGER BALL
DOWNROD
1. Remove the hanger ball by loosening the setscrew in
the hanger ball until the ball falls freely down the
downrod (Figure 9). Remove the pin from the
downrod, then remove the hanger ball. Retain the pin
and hanger ball for reinstallation in Step 7.
SETSCREW
Figure 9
2. Loosen setscrew in motor coupler if necessary.
Separate, untwist and unkink the three 80” motor
leads. Route the motor lead wires through the
downrod. Align the clevis pin holes in the downrod with
the holes in the motor coupler. Install the clevis pin and
secure with the hairpin clip (Figure 10). The clevis pin
must go through the holes in the motor coupler and the
holes in the downrod. Be sure to push the straight leg
of the hairpin clip through the hole near the end of the
clevis pin until the curved portion of the hairpin clip
snaps around the clevis pin. The hairpin clip must be
properly installed to prevent the clevis pin from working
loose. Pull on the downrod to make sure the clevis pin
is properly installed.
!
(Standard)
DOWNROD
SETSCREW (2)
HAIRPIN
CLIP
CLEVIS PIN
Figure 10
WARNING
MOTOR COUPLING
DOWNROD
It is critical that the clevis pin in the motor coupler is
properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
MOTOR COUPLING
SETSCREW (2)
3. While pulling up on the downrod, securely tighten
the two setscrews in the motor coupling
(Figure 11).
NOTE: The setscrews must be properly installed
as described above, or fan wobble could result.
Figure 11
7
U.L. Model No.: CF230
How to Assemble Your Ceiling Fan
4. Make sure the grommet is properly installed in the
coupling cover then slide the coupler cover on
the downrod until it rests on the motor housing
(Figure 12).
(Standard) (cont.)
DOWNROD
CEILING COVER
TRIM RING
5. Place the ceiling cover trim ring and ceiling cover
over the downrod. Be sure both pieces are oriented
correctly (Figure 12).
COUPLING
COVER
GROMMET
Figure 12
6. Place the ceiling cover over the downrod. Be sure it
is oriented correctly (Figure 13).
DOWNROD
7. Reinstall the hanger ball (Figure 14) on the
downrod as follows. Route the motor leads through
the downrod. Position the pin through the two holes
in the downrod and align the ball so the pin is
captured in the groove in the top of the hanger ball.
Pull the hanger ball up tight against the pin and
securely tighten the setscrew in the hanger ball.
A loose setscrew could create fan wobble.
!
CEILING
COVER
WARNING
Figure 13
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
PIN
HANGER BALL
8. The fan comes with blue, black and white leads
that are 80” long. Before installing fan, measure up
approximately 6 to 9-inches above top of hanger
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
DOWNROD
SETSCREW
CEILING
COVER
Figure 14
9. Screw the two 1-1/4” threaded studs (supplied) into
the tapped holes in the hanger bracket (Figure
15).
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES
OMITTED FOR CLARITY.
10. Carefully lift the fan assembly and seat the
hanger ball in the hanger bracket (Figure 15). The
tab on the hanger bracket must seat in the groove
in the hanger ball.
!
WARNING
HANGER
BRACKET
HOOK
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
TAB
GROOVE
Figure 15
8
#8-32 x 1-1/2"
THREADED STUD (2)
HANGER
BALL
U.L. Model No.: CF230
How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
NOTE: Make all wiring connections using wire
connectors (supplied). Make sure that all
connections are tight, including ground, and
that no bare wire is visible at the wire
connectors, except for the ground wire.
4. Refer to Figure 16 and 17 and connect the receiver
wires to the supply wires and the fan motor wires
as follows:
a. Securely connect the green grounding wires from
the hanger ball and the hanger bracket to the
supply grounding conductor (this may be a bare
wire or a wire with green insulation).
b. Securely connect the supply white (neutral) wire to
the receiver white (AC IN N) wire.
c. Securely connect the supply black wire (hot) wire to
the receiver black (AC IN L) wire.
d. Securely connect the fan motor white wire to the
receiver white (TO MOTOR N) wire.
e. Securely connect the fan motor black wire to the
receiver black (TO MOTOR L) wire.
f. Securely connect the fan motor blue wire to the
receiver blue (FOR LIGHT) wire.
NOTE: Failure to properly connect the receiver
wires will damage the device and render it nonoperable.
1. Disconnect electrical power to the branch circuit at
the circuit breaker or fuse box before attempting to
wire the ceiling fan.
2. Position the supply wires to the left side of the
outlet box (Figure 16); position the fan wires to the
right side.
!
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
3. Partially insert the remote control receiver (flat side
up) until one end rests on the hanger ball as shown
in Figure 16. Be sure to insert the antenna wire
first, making certain that it passes completely
through the mounting bracket.
!
(Standard)
WARNING
!
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
9
U.L. Model No.: CF230
How to Wire Your Ceiling Fan
SUPPLY WHITE WIRE
(NEUTRAL)
AC IN
SUPPLY BLACK
WIRE (HOT)
(Standard) (cont.)
RECEIVER WHITE
WIRE
RECEIVER
BLACK WIRE
N
RECEIVER BLACK
WIRE
GROUND WIRE
OTO
RL
TO
M
FAN
BLACK
WIRE
ANTENNA
GREEN GROUND
WIRE FROM
HANGER
BRACKET
1-1/4" THREADED
STUD (2)
GHT
TO MO
AC IN L
FOR LI
GREEN GROUND
WIRE FROM
HANGER BALL
TOR N
RECEIVER
BLUE WIRE
FAN BLUE WIRE
FAN WHITE WIRE
RECEIVER WHITE WIRE
Figure 16
5. After wire connections have been made, separate
the grounded white neutral and green wires on
one side of the outlet box from the ungrounded
black and blue wires on the other side of the outlet
box (Figure 17).
6. Carefully turn the wire connectors upward and
insert them up through the open side of the hanger
bracket and into the outlet box. Push the grounded
green and white wires into one side of the outlet
box; push the ungrounded black and blue wires
into the other side of the outlet box.
STANDARD ON-OFF
WALL SWITCH
TO
120VOLT
SUPPLY
BLACK
BLACK
(HOT)
BLACK (AC IN L)
WHITE
(AC IN)
WHITE
(NEUTRAL)
GROUND
WHITE
BLACK (TO
MOTOR L)
TWO-CONDUCTOR
CABLE (WITH
GROUND)
WHITE (TO MOTOR N)
BLUE (FOR LIGHT)
BLACK
BLUE
WHITE
GREEN WIRE (GROUND)
FROM HANGER BALL AND
HANGER BRACKET
HANGER BALL
Figure 17
10
U.L. Model No.: CF230
Installation of Ceiling Cover
(Standard)
1. Lift the ceiling cover up to the threaded studs and
turn until the studs protrude through the holes in
the ceiling cover (Figure 18).
!
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
2. Position the lower ceiling cover trim ring onto the
threaded studs and secure both the ceiling cover
and ring in place by sliding lockwashers (supplied)
over the threaded studs and installing the two
knurled knobs (supplied). (Figure 18). Tighten the
knurled knobs securely until the ceiling cover fits
snugly against the ceiling.
CEILING
COVER
CEILING COVER
TRIM RING
THREADED STUD (2)
LOCKWASHER (2)
Figure 18
KNURLED KNOB (2)
Close-to-the-Ceiling Installation
Installing The Ceiling Cover On The
Fan Motor Housing
1. Remove and retain three screws from the top of
the motor housing (Figure 19A).
2. Position the rubber gasket (supplied in parts bag)
on the motor housing (small holes in gasket
centered over the screw holes in the housing)
(Figure 19B).
REMOVE SCREWS (3)
Figure 19A
3. Remove the ceiling cover trim plugs pre-installed
to the ceiling cover (Figure 20).
INSTALL RUBBER GASKET
Figure 19B
CEILING COVER
CEILING COVER
TRIM PLUG (2)
Figure 20
4. Align the holes in the ceiling cover with the holes in
the motor housing and secure using the three
screws (Figure 21).
5. The fan comes with blue, black and white leads
that are 80” long. Measure up approximately 6 to
9-inches above the motor coupling. Cut off excess
leads and strip back insulation 1/2-inch from ends
of leads.
RUBBER
GASKET
SCREW (3)
Figure 21
11
U.L. Model No.: CF230
Close-to-the-Ceiling Installation
6. Carefully lift the fan assembly up to the hanger
bracket. Pass the hook on the hanger bracket
(Figure 22) through one of the screw holes (not the
slots) in the ceiling cover (Figure 22). The hook
must pass from the inside of the ceiling cover to
the outside. The hook will hold the fan assembly
while connecting the wiring.
!
CEILING COVER
HOOK
HOOK ON HANGER BRACKET MUST PASS
THROUGH SCREW HOLE IN CEILING
COVER, INSIDE OF BRACKET TO OUTSIDE
OF BRACKET
WARNING
The hook must pass through the screw hole in the
ceiling cover from the inside to the outside. Any
other hanging method may cause the hook to break
and the fan to fall.
HANGER
BRACKET
Figure 22
How to Wire Your Ceiling Fan
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
1. Disconnect electrical power to the branch circuit at
the circuit breaker or fuse box before attempting to
wire the ceiling fan.
2. Position the supply wires to the left side of the
outlet box (Figure 23); position the fan wires to the
right side.
!
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.
3. Partially insert the remote control receiver (flat side
up) until one end rests on the hanger bracket as
shown in Figure 23. Be sure to insert the antenna
wire first, making certain that it passes completely
through the mounting bracket.
!
(cont.)
(Close-to-the-Ceiling)
NOTE: Make all wiring connections using wire
connectors (supplied). Make sure that all
connections are tight, including ground, and
that no bare wire is visible at the wire
connectors, except for the ground wire.
4. Refer to Figure 23 and connect the receiver wires
to the supply wires and the fan motor wires as
follows:
a. Securely connect the green grounding wires from
the hanger ball and the hanger bracket to the
supply grounding conductor (this may be a bare
wire or a wire with green insulation).
b. Securely connect the supply white (neutral) wire to
the receiver white (AC IN N) wire.
c. Securely connect the supply black wire (hot) wire to
the receiver black (AC IN L) wire.
d. Securely connect the fan motor white wire to the
receiver white (TO MOTOR N) wire.
e. Securely connect the fan motor black wire to the
receiver black (TO MOTOR L) wire.
f. Securely connect the fan motor blue wire to the
receiver blue (FOR LIGHT) wire.
NOTE: Failure to properly connect the receiver
wires will damage the device and render it nonoperable.
WARNING
!
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
12
U.L. Model No.: CF230
How to Wire Your Ceiling Fan (Close-to-the-Ceiling) (cont.)
SUPPLY WHITE WIRE
(NEUTRAL)
SUPPLY BLACK
WIRE (HOT)
AC IN
RECEIVER WHITE
WIRE
RECEIVER
BLACK WIRE
N
RECEIVER BLACK
WIRE
GROUND WIRE
OTO
RL
TO
M
FAN
BLACK
WIRE
ANTENNA
GREEN GROUND
WIRE FROM
HANGER
BRACKET
TOR N
TO MO
AC IN L
FOR LI
GREEN GROUND
WIRE FROM
HANGER BALL
GHT
RECEIVER
BLUE WIRE
FAN BLUE WIRE
FAN WHITE WIRE
RECEIVER WHITE WIRE
Figure 23
Installation of Fan Assembly onto
Hanger Bracket (Close-to-the-Ceiling)
1. Partially install two #10-24x3/16 pan head screws
and lock washers (supplied) into the hanger
bracket as shown (Figure 24). Observe the ceiling
cover to determine exact installation location of
both screws. The protruding screws will be used to
engage the ceiling cover.
2. Lift the fan assembly up to the hanger bracket.
Engage the slots in the ceiling cover with the
loosened screws in the bracket and turn the cover
counterclockwise (Figure 24). Be sure that the
lockwashers are between the screw heads and the
ceiling cover. Immediately tighten both screws to
lock the fan onto the hanger bracket.
3. Install the two #10-24x3/16 screws and
lockwashers (supplied) into the hanger bracket ;
tighten all screws securely.
!
TIGHTEN SCREW
INSTALL SCREW AND WASHER
INSTALL TWO #10-24 x 3/16
PAN HEAD SCREWS AND
LOCKWASHERS
FAN
ASSEMBLY
WARNING
Figure 24
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
13
U.L. Model No.: CF230
Installation of Light Bulb & Lower Cover (All Fans)
1. Install the 50-watt (maximum) GU10 base light bulb
(supplied) into the light socket (Figure 25). Turn
bulb clockwise to engage into the socket for secure
fit.
NOTE: Do not touch the new 50-watt (maximum)
MR-16, GU-10 bulb with your bare fingers; using a
cloth or soft gloves to hold the bulb, gently push
it into the socket and twist to lock the lamp into
the socket (Figure 25). If there is any doubt that
the bulb may have been contaminated by your
touch, you should clean the bulb before its first
use. Take a clean cloth dipped in a small amount
of rubbing/isopropyl alcohol and gently brush off
the bulb surface. If the lamp is hot, wait 30
minutes before cleaning.
Figure 25
50-WATT GU10
BASE LIGHT BULB
CAUTION: To reduce the risk of electric shock,
burns or other injury, disconnect the electric
supply circuit to the fan before attempting to
install or replace the halogen bulb.
CAUTION: To not touch halogen bulbs with bare
hands. Fingerprints may result in shorter bulb life.
Remove fingerprints with alcohol.
LIGHT SWITCH
PIN (3)
2. Place the lower cover into the opening in the light
kit plate assembly. Place the three pins on the light
kit plate assembly into the three mounting holes
located on the underside of the lower cover. Turn
the lower cover clockwise until it stops and locks
into place (Figure 26).
LOWER COVER
PIN (3)
LOWER
COVER
Figure 26
3. You have now completed the assembly of your
new ceiling fan. Proceed to the next section to
program your remote controls.
NOTE: Periodically check that the cover is seated
fully clockwise in the light kit plate assembly.
Remote Control Procedures
General
Preset Memory Feature
Your Emerson Ceiling Fan/Light Remote Control
consists of hand-held transmitter and a receiver which
is mounted under the fan ceiling cover. The remote
control is designed to separately control your ceiling
fan speed and light intensity.
The remote control transmitter is powered by two AAA
alkaline batteries (included). To prevent possible
damage if the batteries should leak, be sure to
remove the batteries when the control is not to be
used for an extended period of time.
Code switches in the transmitter and receiver may be
set in 32 different positions. If your fan and light go on
and off without using your control, you may be getting
interference from other remote units such as garage
door openers, car alarms or security systems. To
remedy this situations, simply change the combination
code in your transmitter and receiver.
Your Emerson receiver is equipped with a preset
memory feature. If the AC supply to the receiver is
powered through a wall switch, when the switch is
turned OFF, the control will remember the light
intensity and fan speed. When the switch is turned
back ON the light and fan will resume operation as
they were prior to the switch being turned OFF.
14
U.L. Model No.: CF230
Remote Control Procedures
(cont.)
Installation of Battery
1. Remove the battery cover by pressing firmly below
the arrow and sliding the cover off the control
(Figure 27).
2. Install two AAA alkaline batteries and reinstall the
battery cover.
REMOTE CONTROL
LEVERS
1
2
3
4 5
TWO AAA
BATTERIES
CODE
SWITCHES
Figure 27
BATTERY
COMPARTMENT
COVER
REMOTE CONTROL
Installation of Storage Bracket for Remote Control
A storage bracket is provided for holding your remote
control when not in use. If you desire to use the
bracket, install it on a wall that is away from excess
heat or humidity (Figure 28).
TO INSTALL BRACKET TO WALL:
SLIDE THE COVER UP TO EXPOSE THE SCREW
HOLES FOR INSTALLATION
COVER
WALL
BRACKET
SCREW
HOLES (2)
Figure 28
Setting Operating Frequency of Remote Control
Your remote control has code switches which must be 2. Restore electrical power to the ceiling fan at the
set in one of 32 possible code combinations
circuit breaker panel or fuse box.
(Figure 29). The five levers (numbered 1, 2, 3, 4, 3. Within 1 minute of restoring electricity, push and
and 5) on the switches are factory-set in the ON (up)
hold the remote control OFF button ( ) for 3 to 5
position. Change the switch settings as follows
seconds to set the code in the receiver. The fan's
(Figure 29):
lights will blink several times to confirm the fan is
programmed.
1. Slide the five switch levers in the remote control to
your choice of ON (up) or down positions. Use a NOTE: The ceiling fan receiver will not respond to
ball-point pen or small screwdriver and slide the transmitter commands if the transmitter’s
levers firmly up or down.
frequency switch settings are changed without
reprogramming the receiver. Program the receiver
to the new frequency by repeating the “Setting
Operating Frequency of Remote Control” and
“High Speed Conditioning” instructions.
15
U.L. Model No.: CF230
Remote Control Procedures
(cont.)
Operating Your Ceiling Fan
1. To turn on or shut off the ceiling fan, press and
release the ( ) button.
2. To set the desired fan speed, press the (
)
button to decrease the speed and the (
) to
increase the speed. The LED display will light up
to indicate the new speed selected.
3. To turn the downlight on or off, press and release
the ( ) button.
4. To vary the intensity of the light, hold the (
)
button down until the desired light intensity is
reached, then release the button. The remote
dimmer code must be set to “D” to use the
dimming features (Figure 29).
Figure 29
Reversing Air Circulation
1.All fans are shipped from the factory with the
reversing switch positioned to circulate air
downward. If airflow is desired in opposite
direction, turn your fan off and wait for the blades to
stop turning, then slide the reversing switch to the
opposite position, and turn fan on again
(Figure 30).
REVERSING
SWITCH
2. The fan blades will turn in the opposite direction
and reverse the airflow.
Season
Summer
Winter
Figure 30
Reverse Switch Information
Rotation
Switch
Direction
Position
Counter-Clockwise
Right
Clockwise
Left
Energy Efficient Use of Ceiling Fans
Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the
ceiling fan. Here are a few tips to ensure quality and
product performance.
Using the Ceiling Fan Year Round. In the summer,
use the ceiling fan in the counter-clockwise direction.
The airflow produced by the ceiling fan creates a
wind-chill effect, making you "feel" cooler. Select a
fan speed that provides a comfortable breeze, lower
speeds consume less energy. In the winter, reverse
the motor and operate the ceiling fan at low speed in
the clockwise direction. This produces a gentle
updraft, which forces warm air near the ceiling down
into the occupied space. Remember to adjust your
thermostat when using your ceiling fan - additional
energy and dollar savings could be realized with this
simple step!
Choosing the Appropriate Mounting Location.
Ceiling fans should be installed, or mounted, in the
middle of the room and at least 7 feet above the floor
and 18 inches from the walls. If ceiling height allows,
install the fan 8 - 9 feet above the floor for optimal
airflow. Consult your Emerson Retailer for optional
mounting accessories.
Turn Off When Not in the Room. Ceiling fans cool
people, not rooms. If the room is unoccupied, turn off
the ceiling fan to save energy.
16
U.L. Model No.: CF230
Trouble Shooting
!
WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble shooting your fan.
TROUBLE
1. Fan will not start.
PROBABLE CAUSE
1. Fuse or circuit breaker blown.
1.Check main and branch circuit fuses or circuit
breakers.
2. Loose electrical connections to the fan.
2.Check line wire connections to fan .
! WARNING: Make sure main power is
turned OFF.
3.Make sure reversing switch position is all the
way to one side.
3. Reversing switch in neutral position.
4. Fan wall switch is OFF.
2. Fan sounds noisy.
SUGGESTED REMEDY
4.Turn the switch ON.
5. Fan/Light remote control is OFF.
5.Turn ON fan/light remote control.
6. Remote control battery is weak.
6.Replace the remote control batteries.
1. Blades not attached to fan.
1.Attach blades to fan before operating.
2. Loose screws in motor housing.
2.Check to make sure all screws in motor
housing are snug (not over-tight).
3. Screws securing fan blade flanges to
motor hub are loose.
3.Check to make sure the screws which attach
the fan flanges to the motor hub are tight.
!
3. Fan wobbles
excessively.
WARNING: Make sure main power is
turned OFF.
4. Screws holding blades to flanges
are loose.
4.Tighten screws securely.
1. Setcrews in motor coupling are not
tightened securely.
1.Raise coupling cover and tighten setscrews
securely.
2. Setscrew in hanger ball/downrod
assembly is loose.
2.Tighten the setscrew in the hanger ball/
downrod assembly.
3. Screws securing fan blades to motor are
loose.
3.Check to be sure screws which attach the fan
blade to the motor are tight.
4. Fan blades are not seated properly.
4.Check to be sure that the screws securing the
fan blades seat firmly.
5. Hanger bracket and/or ceiling outlet box
is not securely fastened.
5.Tighten the hanger bracket screws to the
outlet box, and /or secure outlet box.
6. Fan blades out of balance.
6.Interchanging an adjacent (side-by-side)
blade pair can redistribute the weight and
result in smoother operation.
Or use supplied balancing kit to balance
blades.
17
U.L. Model No.: CF230
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
!
WARNING
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Accessories
1. Ceiling Fan/Light Controls (see store or catalog).
!
2. Ceiling Fan Blades (see store or catalog).
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
WARNING
!
WARNING
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
Repair Parts
27
16
4
26
1
28
18
8
2
5
6
7
3
13
17
10
9
21
19
20
12
22
15
14
11
23
25
24
18
U.L. Model No.: CF230
Repair Parts Listing
Key
No.
Description
CF230BS00
Model Numbers
CF230ORB00
CF230WW00
1
2
3
Hanger Pack,
Consisting of:
Hanger Bracket (1)
Hanger Ball (1)
Downrod 4.5” (1)
762231-4
—
—
—
762231-8
—
—
—
762231-1
—
—
—
*
4
5
6
7
8
9
10
11
12
13
14
15
16
Parts Bag Containing:
12 ga. Wire Connectors (3)
Stud, Threaded #8-32 x 1-1/4” (2)
Lockwasher, External Tooth #8-32 x 1-1/4” (2)
Knob, Knurled #8-32 (2)
#10-24 x 5/16” Flange Head Blade Screws (13)
#10-24 x 3/16” Pan Head Screws (4)
#10 External Tooth Lock Washer (4)
Clevis Pin (1)
Hairpin Clip (1)
Rubber Gasket (1)
#8-32 x 5/16” Light Switch Screw (1 Spare)
1/4-20 x 9/16” Flange Screw w/Lockwasher (1 Spare)
Balancing Kit (1)
764149
—
—
—
—
—
—
—
—
—
—
—
—
—
764149-1
—
—
—
—
—
—
—
—
—
—
—
—
—
764149
—
—
—
—
—
—
—
—
—
—
—
—
—
17
Cover, Ceiling (1)
764138-BS
764138-ORB
764138-WW
18
Ceiling Cover Trim Plug (2)
764030-BS
764030-ORB
764030-WW
19
Ceiling Cover Trim Ring (1)
764031-BS
764031-ORB
764031-WW
20
Cover, Coupler (1)
764139-BS
764139-ORB
764139-WW
21
Fan Blades (4)
764144-BS/CH
764144-ORB/DC
764144-BS/WW
22
Fan Blade Flanges (4)
764142-BS
764142-ORB
764142-WW
23
Light Kit Plate Assembly (1)
764146-BS
764146-ORB
764146-WW
24
Cover, Lower (1)
764147-BS
764147-ORB
764147-WW
25
Wiring Harness (1)
764148
764148
764148-1
26
Light Bulb, 50-Watt GU10 (1)
763494
763494
763494
27
Receiver
RCFP
RCFP
RCFP
28
Transmitter SR401
764090
764090
764090
—
Owner's Manual
BP7434
BP7434
BP7434
*
Before discarding packaging material, be certain all
parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
•
•
•
•
PART NUMBER
PART DESCRIPTION
NAME OF ITEM
MODEL NUMBER
For repair parts, phone 1-800-654-3545.
19
U.L. Model No.: CF230
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in
workmanship and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for the lifetime of your ceiling fan. All other components and accessories are
covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND
ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at
no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can
be provided, Emerson will refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED PRODUCT OR
REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OR REMOVAL, REINSTALLATION
AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR
RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service
center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort
Products, Division of Emerson Electric Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers
shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service
center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service
center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be
responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any
defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral
warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson
Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND
EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES.
Incidental damages include but are not limited to such damages as loss of time and loss of use. Consequential damages
include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work
properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Part No. F40BP74340000
Printed in China 06/11
Form No. BP7434
U.L. Model No.: CF230