R-1502
SUPPLEMENTAL SERVICE MANUAL
S12M181R1502E
OVER THE RANGE
MICROWAVE OVEN
Light
Fan
MODELS
Stop
Clear
Start
Minute Plus
R-1502
Model R-1502
This is a supplemental Service Manual for Model R-1502.
This model is quite similar to Base Model R-1500 (S/M# S8118R1500X//).
Use this supplemental manual together with the Base Model Service Manual for complete operation and service information
In the interest of user-safety the oven should be restored to its original condition and only parts identical to those specified
should be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe, possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..)
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ...................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................ 1
MICROWAVE MEASUREMENT PROCEDURE .....................................................................................................2
FOREWORD AND WARNING ................................................................................................................................3
PRODUCT SPECIFICATIONS ............................................................................................................................... 4
GENERAL INFORMATION ...................................................................................................................................4
PARTS LIST .......................................................................................................................................................... 7
PACKING AND ACCESSORIES ........................................................................................................................... 9
SHARP ELECTRONICS CORPORATION
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
Service Headquarters: Sharp Plaza, Mahwah, New Jersey, 07430-2135
R-1502
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary: (1) interlock operation (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation
and transmission systems shall be repaired, replaced, or adjusted by procedures described in this
manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS
CORPORATION immediately @1-800-237-4277.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's Center
for Devices and Radiological Health immediately.
Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit found
with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit
until the oven has been brought into compliance.
R-1502
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
When the testing is completed,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
Before Servicing
1. Disconnect the power supply cord
remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
, and then
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for 60
seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an
insulated screwdriver.
After repairing
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
Whenever troubleshooting is performed the power supply
must be disconnected. It may, in some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that these leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out Before Servicing procedure and reexamine the connections to the component being tested.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and microwave leakage test should be carried out.
1
R-1502
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches: Primary interlock relay and door sensing switch shall prevent microwave radiation emission in
excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation emission in
excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for
microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5C (68F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and
made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode.
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed, replace
it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on the
meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2, and
that the secondary interlock switch does turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
R-1502
SUPPLEMENTAL
SERVICE MANUAL
PRODUCT DESCRIPTION
MICROWAVE OVEN
GENERAL INFORMATION
R-1502
PARTS LIST
FOREWORD
This Manual has been prepared to provide Sharp Electronics Corp.
Service Personnel with Operation and Service Information for the SHARP
MICROWAVE OVEN, R-1502.
The model R-1502 is quite similar to base model R-1500(Ref.#
S8123R1500X//)
It is recommended that service personnel carefully study the entire text
of this manual and the base model's manual so that they will be qualified
to render satisfactory customer service.
Check the interlock switches and the door seal carefully. Special
attention should be given to avoid electrical shock and microwave
radiation hazard.
WARNING
Never operate the oven until the following points are ensured:
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
Servicing and repair work must be carried out only by trained service
personnel.
DANGER
Certain initial parts are intentionally not grounded and present
a risk of electrical shock only during servicing. Service personnel - Do not contact the following parts while the appliance is
energized;
High Voltage Capacitor, Power Transformer, Magnetron, High
Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more than
250V.
Removal of the outer wrap gives access to voltage above 250V.
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH,
NEW JERSEY 07430-2135
3
R-1502
PRODUCT SPECIFICATION
ITEM
DESCRIPTION
Power Requirements
120 Volts / 14 Amperes
60 Hertz
Single phase, 3 wire grounded
Power Output
1000 watts (IEC TEST PROCEDURE)
Operating frequency of 2450MHz
Case Dimensions
Width 29-15/16"
Height 16-1/4"
Depth 15- 9/16"
Cooking Cavity Dimensions
1.5 Cubic Feet
Width 17-1/2"
Height 9-7/8"
Depth 14-15/16"
Hood lamp
2 bulbs, 20W x 2, Incandescent light bulbs
Hood fan
Approx. 300 C.F.M.
Control Complement
Touch Control System
Clock ( 1:00 - 12:59 )
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI ................................................. Full power throughout the cooking time
P-90 .................................................................... approx. 90% of Full Power
P-80 .................................................................... approx. 80% of Full Power
P-70 .................................................................... approx. 70% of Full Power
P-60 .................................................................... approx. 60% of Full Power
P-50 .................................................................... approx. 50% of Full Power
P-40 .................................................................... approx. 40% of Full Power
P-30 .................................................................... approx. 30% of Full Power
P-20 .................................................................... approx. 20% of Full Power
P-10 .................................................................... approx. 10% of Full Power
P-0 .................................................... No power throughout the cooking time
KEEP WARM pad, POPCORN pad, HOT WATER pad
REHEAT CENTER pads, COOK CENTER pads
DEFROST CENTER pads, Number selection pads
POWER LEVEL pad, TIMER / CLOCK pad
LIGHT HI / LO button, FAN HI / LO button,
STOP/CLEAR button, START/ MINUTE PLUS button,
Oven Cavity Light
20W x 1 Incandescent light bulb
Safety Standard
UL Listed
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
Weight
Approx. 55 lbs.
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed and
grounded in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric
current.
WARNING:
Improper use of the grounding plug can result in a risk of electric shock.
4
R-1502
Electrical Requirements
The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE
GROUNDING PIN FROM THE PLUG.
The power supply cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp. or more dedicated line, using
a grounded receptacle. The receptacle should be located inside the cabinet directly above the Microwave Oven/Hood system
mounting location.
3-Pronged Plug
Grounded
Receptacle Box
Grounding Pin
3-Pronged Receptacle
OVEN DIAGRAM
10
10
1
15
9
5
2
6
8
4
3
7
10 12
13
11
14
1.
2.
3.
4.
5.
6.
7.
8.
9.
Oven door with see-through window.
Door hinges.
Waveguide cover.
Turntable motor shaft.
Oven lamp.
It will light when oven is operating or door is open.
Door latches.
The oven will not operate unless the door is
securely closed.
One touch door open button.
Auto Touch control panel
Time display: Digital display, 99 minutes 99
seconds.
5
10.Ventilation openings.
11.Light Cover.
12.Grease filters.
13.Removable turntable.
The turntable will rotate clockwise or
counterclockwise.
Only remove for cleaning.
14.Removable turntable support.
15. Power supply cord
R-1502
1 0 0 0
WATTS
NO.
LBS.
CUPS
OZ.
COOK DEFROST
KEEP
WARM
HOT
WATER
POPCORN
REHEAT CENTER
1
2
3
4
Casserole
Soup
Pizza
Beverage
5
6
7
8
Dinner Plate
Fresh Rolls / Muffins
Frozen Rolls / Muffins
Canned Vegetables
LIGHT HI/ LO
COOK CENTER
BAKED
POTATOES
RICE
FROZEN
VEGETABLES
FRESH
VEGETABLES
GROUND
MEAT
FROZEN
ENTREES
DEFROST CENTER
GROUND
MEAT
STEAKS/
CHOPS
POULTRY
BONELESS
POULTRY
BONE-IN
1
2
3
4
5
6
7
8
9
POWER
LEVEL
0
TIMER
CLOCK
FAN HI/ LO
STOP
CLEAR
START
MINUTE PLUS
NOTE: Some one-touch cooking features such as "MINUTE PLUS" are disabled after three minutes when the oven is not
used. These features are automatically enabled when the door is opened and closed or STOP/CLEAR button is
pressed.
6
R-1502
PARTS LIST
Note: The parts marked “∆
∆” may cause undue microwave exposure.
The parts marked “*” are used in voltage more than 250V.
REF. NO.
PART NO.
§
"§" MARK: PARTS DELIVERY SECTION
DESCRIPTION
Q'TY CODE
ELECTRIC PARTS
*
*
*
∆*
1- 1
1- 2
1- 3
1- 4
1- 5
1- 6
1- 7
1- 8
1- 9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
FH-DZB016MRY0
RC-QZA234WRE0
QFS-TA013WRE0
RMOTDA211WRE0
RTHM-A070WRE0
RTHM-0044MRE0
RTRN-B068MRE0
RV-MZA288WRE0
QFSHDB003MRE0
QSW-MA085WRE0
FFS-BA016/KIT
FACCDB011MRE0
QSOCLB006MRE0
FMOTEA441WRKZ
RMOTEB031MRE0
RLMPTA068WRE0
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
High voltage rectifier assembly
High voltage capacitor
Temperature fuse 150½C (Magnetron)
Turntable motor
Thermal cut-out 145½C (Cavity)
Thermal cut-out N.O. 60½C (Hood Fan)
Power transformer
Magnetron
Fuse holder
Primary interlock and door sensing switches
Monitor switch (V-16G-2C25) with fuse (20A) assembly
Power supply cord
Oven lamp socket
Hood fan motor
Fan motor
Oven lamp
1
1
1
1
1
1
1
1
1
2
1
1
3
1
1
3
AH
AP
AE
AL
AF
AH
BC
BK
AD
AE
AF
AQ
AE
BC
AR
AE
1
1
1
1
1
1
1
1
1
1
AE
AQ
AG
AL
AZ
AB
AK
AG
AH
AQ
1
1
1
1
1
1
1
1
1
4
7
1
1
2
1
2
1
3
1
1
1
1
1
1
1
1
1
1
5
BF
AA
AA
AB
AB
AB
AF
AB
AK
AD
AA
AA
AB
AB
AA
AG
AG
AG
AG
BG
AE
AZ
AQ
AE
AC
AA
AC
AR
AB
1
1
1
1
1
AB
AN
AN
AB
AF
CABINET PARTS
2- 1
2- 2
2- 3
2- 4
2- 5
2- 6
2- 7
2-7-1
2-7-2
2- 8
LSTY-B024MRP0
M
PDIF-B034MRF0
M
GDAI-B065MRP0A M
HDECQB035MRF0A M
GCABUB110MRP0
M
TMAPCB067MRR0
M
FANGKB013MRY0
M
LANGQB049MRP0
M
PGLSPB004MRE0
M
PCOVPB102MRT0
M
Rear stay
Hood exhaust louver
Base plate R
Front panel L
Outer case cabinet
Schematic diagram
Hood lamp glass assembly
Hood lamp glass angle
Hood lamp glass
Base cover
CONTROL PANEL PARTS
3- 1
3- 1A
3- 1B
3- 1C
3- 1D
C1
C2
C21
C100
D1-4
D20-26
D40
Q21
R1-2
R30
RY1-2
RY3
RY4-6
SP1
T1
VRS1
3- 2
3- 2-1
3- 2-2
3- 2-3
3- 2-4
3- 3
3- 4
3- 5
CPWBFB060MRU0
QCNCMA017JDZZ
QCNCMA448DRE0
QCNCMA275DRE0
FW-VZB189MRE0
RC-KZA087DRE0
VCEAB31VW108M
VCEAB31VW106M
RC-QZB014MRE0
RH-DZA006PRE0
VHD1SS270A/-1
VHD1SS270A/-1
VSKRC243M//-3
VRS-B13AA751J
VRD-B12EF332J
RRLY-A113DRE0
RRLY-A123DRZZ
RRLY-B004MRE0
RALM-A014DRE0
RTRNPB017MRE0
RH-VZA032DRE0
FPNLCB401MRK0
FUNTKB345MRE0
JBTN-B125MRF0
JBTN-B126MRF0
MSPRTA050WRE0
LHLD-B018MRF0
PSHEPB023MRE0
XEPSD30P10XS0
M
M
M
J
M
J
J
J
M
J
J
J
J
J
J
M
M
M
J
M
J
M
M
M
M
M
M
M
M
Control unit
3-pin connector CN-A
5-pin connector CN-B
2-pin connector CN-E
Lead wire harness CN-C
Capacitor
0.1 uF
50V
Capacitor
1000 uF
35V
Capacitor
10 uF
35V
Capacitor
7 uF
230V
Diode (1N4002)
Diode (1SS270A)
Diode (1SS270A)
Transistor (KRC243M)
Resistor
750 ohm
1W
Resistor
3.3k ohm
1/4W
Relay (DU24D1-1PR(M))
Relay (G5S-1 24V)
Relay (FTR-F3AA024E)
Buzzer (PKM22EPT)
Transformer
Varistor (10G471K)
Control panel sub. assembly
Key unit
Open button
Select button
Button spring
LCD holder
LED sheet
Screw; 3mm x 10mm
44444-
LSTPPB038MRF0
FROLPB025MRK0
NTNT-A095WRE0
LBNDKB009MRP0
PDUC-B111MRF0
M
M
M
M
M
Door stopper
Turntable support assembly
Turntable tray
Capacitor holder
Magnetron duct
OVEN PARTS
1
2
3
4
5
7
R-1502
REF. NO.
4- 6
4- 7
4- 8
4- 9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
4-18
4-19
4-20
4-21
4-22
PART NO.
MLEVPB016MRF0
*************
PPACGB014MRF0
PHOK-B018MRF0
FANGTB005MRY0
NFANPB006MRE0
LBSHC0037WRE0
MLEVFB007MRP0
PDUC-B112MRP0
PCOVPB085MRP0
MSPRTA046WRE0
LANGTB055MRP0
PDUC-B115MRF0
PDUC-B114MRF0
PDUC-B113MRP0
PDUC-B117MRF0
PCUSGB043MRP0
§
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
DESCRIPTION
Open lever
Oven cavity (Not replaceable part)
Turntable motor packing
Latch hook
Unit mounting plate assembly
Fan blade
Cord bushing
Mounting lever
Hood intake duct R
Waveguide cover
Latch spring
Chassis support
Hood duct R
Hood duct L
Fan duct
Orifice
Transformer cushion
5
5- 1
5- 2
5-2-1
5-2-2
5-2-3
5- 3
5- 4
5- 5
CDORFB304MRK0
FDORFB070MRT0
FCOV-B209MRK0
LSTPPB021MRF0
MSPRTA046WRE0
LSTPPB037MRF0
GCOVHB044MRF0
PSHEPB021MRE0
XCPSD40P08000
M
M
M
M
M
M
M
M
M
Door assembly
Door panel assembly
Door frame assembly
Latch head
Latch spring
Glass stopper
Choke cover
Sealer film
Screw : 4mm x 8mm
Q'TY CODE
1
AD
1
-1
AA
1
AF
1
AS
1
AC
1
AB
2
AC
1
AG
1
AH
2
AB
2
AD
1
AQ
1
AQ
1
AH
1
AC
1
AC
DOOR PARTS
1
1
1
1
1
2
1
1
2
BD
AW
AY
AD
AB
AC
AG
AE
AA
1
1
4
1
2
3
6
2
2
1
1
1
1
2
1
1
1
1
2
1
AH
AC
AC
AB
AA
AA
AA
AA
AD
AD
AD
AT
AT
AA
AA
AB
AT
AE
AF
AH
3
4
18
2
6
2
4
2
1
1
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
MISCELLANEOUS
6- 1
6-1-1
6-1-2
6-1-3
6-1-4
6-1-5
6-1-6
6-1-7
6-1-8
6- 2
6- 3
6- 4
6- 5
6- 6
6- 7
6- 8
6- 9
6-10
6-11
6-12
CFZK-B460MRK0
LBSHC0040MRE0
LX-BZ0195WRE0
LX-MZB001MRE0
XBRSD50P60000
XOTSD40P12000
XTSSD50P35000
XWHSD50-16300
LANG-B002MRP0
TINSKB081MRR0
TINSEB296MRK0
QW-QZB025MRE0
FW-VZB187MRE0
TCAUAB041MRR0
TCAUAB037MRR0
TCAUAB005MRR0
FW-VZB188MRE0
PFIL-B006MRE0
PFIL-B002MRE0
FFTA-B005MRK0
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
Installation material assembly
Grommet
Toggle screw
Cord holder
Screw : 5mm x 60mm
Screw : 4mm x 12mm
Screw : 5mm x 35mm
Washer
Scale plate
Top/wall template
Operation manual/Installation instructions
High voltage wire A
Main harness
DHHS service caution label
Monitor caution label
Revised DHHS/GRD C/label
Low voltage harness
Charcoal filter
Grease filter
Exhaust damper assembly
SCREWS,NUTS AND WASHERS
7- 1
7- 2
7- 3
7- 4
7- 5
7- 6
7- 7
7- 8
7- 9
7-10
LX-CZB016MRE0
XOTSD40P12000
XOTSD40P12000
XHTSD40P08RV0
LX-CZA038WRE0
LX-CZ0052WRE0
LX-BZA041WRE0
XCPSD30P08000
LX-BZA041WRE0
XCBSD30P08000
M
M
M
M
M
M
M
M
M
M
Special
Screw :
Screw :
Screw :
Special
Special
Screw :
Screw :
Special
Screw :
screw
4mm x
4mm x
4mm x
screw
screw
4mm x
4mm x
screw
3mm x
12mm
12mm
8mm
8mm
8mm
8mm
8
R-1502
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
Order Parts from the authorized SHARP parts Distributor for your area.
Defective parts requiring return should be returned as indicated in the Service Policy.
PACKING AND ACCESSORIES
4-3 TURNTABLE TRAY
TOP PAD
6-11 GREASE FILTER (x 2)
6-2 TOP / WALL TEMPLATE
DOOR PROTECTOR
6-3
OPERATION MANUAL / INSTALLATION INSTRUCTION
6-1 INSTALL MATERIAL ASSEMBLY
WRAP COVER
6-12 EXHAUST DAMPER
ASSEMBLY
ACCESSORY PACK
DOOR PAD
BOTTOM PAD
Non-replaceable items
PACKING CASE
9
R-1502
2
1
4
3
6
5
OVEN AND CABINET PARTS
A
A
6-1-5
6-12
4-10
7-3
2-1
7-3
B
7-5
2-5
7-3
B
7-3
7-5
4-12
1-12
7-5
4-19
7-5
1-14
C
C
2-6
7-3
7-3
4-17
7-3
4-16
4-18
4-13
D
D
4-17
2-4
2-2
7-3
4-7
6-8
7-8
6-10
4-16
1-3
E
7-1
4-15
6-7
7-6
4-8
6-6
4-3
F
1-9
1-4
7-10
4-5
1-7
1-11
1-5
4-6
1-10
2-8
1-16
7-8
4-4
7-9
E
1-1
1-16
1-10
1-11
1-2
7-4
4-11
1-8
4-9
1-15
4-20
4-13
7-7
1-13
F
4-21
4-14
4-22
1-6
1-13
7-3
4-2
2-3
G
7-3
7-3
7-2
G
7-3
7-3
6-11
2-7-2
6-11
2-7
H
2-7-1
H
7-2
1
2
4
3
10
5
6
R-1502
2
1
4
3
6
5
A
A
CONTROL PANEL PARTS
3-5
3-3
3-4
3-1
3-2
3-5
B
3-5
B
3-2-1
DOOR PARTS
4-1
5
7-3
C
C
3-2-3
5-3
3-2-2
5-4
3-2-4
5-5
D
D
5-1
5-2-3
5-5
5-2-3
E
E
5-2-1
5-2-2
5-2
6-4
F
F
MISCELLANEOUS
6-5
6-1
6-1-1
6-1-4
G
G
6-1-5
6-1-2
6-1-6
6-9
6-1-7
6-1-3
6-1-8
H
H
1
2
4
3
11
5
6
R-1502
NOTES
12
R-1502
NOTES
13
R-1502
COPYRIGHT © 2002 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in retrieval systems, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the
publisher.
2002 SHARP CORP. (2M2.20E) Printed in U.S.A
14