Divitec D1 User manual

Add to my manuals
70 Pages

advertisement

Divitec D1 User manual | Manualzz

D1 Dome Network Camera

VP Dome Network Camera

User’s Manual

English Version 1.0

Copyright ⓒ 2007

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

PROCUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT

THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

CAUTION

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product

’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

2

FCC COMPLIANCE STATEMENT

INFORMATION TO THE USER

: THIS EQUIPMENT HAS BEEN TESTED AND FOUND

TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF

THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION

AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A

COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE

RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH

THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO

COMMUNICATIONS.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL

INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE

INTERFERENCE AT HIS OWN EXPENSE.

INFORMATION TO THE USER

: THIS EQUIPMENT HAS BEEN TESTED AND FOUND

TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF

THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION

AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A

COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE

RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH

THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO

COMMUNICATIONS.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL

INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE

INTERFERENCE AT HIS OWN EXPENSE.

CAUTION

:

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY

RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE

THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMERIQUE DE LA CLASSE A SET CONFORME A LA NORME NMB-003 DU

CANADA.

CE COMPLIANCE STATEMENT

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

3

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been moisture, does not operate normally, or has been dropped.

15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY

QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF

ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN

THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU

QRE QUALIFIED TO DO SO.

16.

Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed

Class 2 power source only.

17. ITE is to be connected only to PoE networks without routing to the outside plant.

4

Table of Contents

1. Product Description…………………………………………………………………………………………………6

2. Installation……………………………………………………..........................…………..……………….8

3. Operation…………………………………………………………………………………………………………….13

3.1 Access from a browser …………………………………………………………………………………..13

3.2 Access from the internet ………………………………………………………………………………..14

3.3 Setting the admin password over a secure connection…………………………….…….…14

3.4 Live View Page ………………………………………………………………………………………………15

3.5 Camera Setup (Analog)……………………………………………………………………………….….17

3.5.1 Settings…………………………………………………………………………………………………..17

3.5.2 Lens Adjustment (Optical Vari-focal Lens)…………………………………………………..23

3.6 Network Camera Setup………………………………………………………………………………...24

3.6.1 Basic Configuration…………………………………………………………………….…………...25

3.6.1.1 Users…………………………………………………………………………………….………...25

3.6.1.2 Network……………………………………………………………………………….…………...26

3.6.1.3 Video & Image..……………………………………………….……………………………...27

3.6.1.4 Audio..…..……………………………………………………….…………………………….....30

3.6.1.5 Date & Time..……………………………………………………………………….………...31

3.6.2 Video & Image..……………..……………………………………………………………………....32

3.6.3 Audio..……………………………….………………………………………………………………....35

3.6.4 Event………………………………………………………………………………………………………36

3.6.4.1 Event-In…………………………………………………………………………………………….36

3.6.4.2 Event-Out………………………………………………………………………………………….41

3.6.4.3 Event Map…………………………………………………………………………………………48

3.6.5 System……………………………………………………………………………………….………...49

3.6.5.1 Information………………………………………………………….…………………………...49

3.6.5.2 Security..…………………………………………………………….…………………………...50

3.6.5.3 Date & Time..…………………………………………………………………….…………...53

3.6.5.4 Network..……………………………………………………………………….……………....54

3.6.5.5 Language..……………….…………………………………….……………………………....61

3.6.5.6 Maintenance..……………..………………………………….…..........................…....62

3.6.5.7 Support............……………………………………….........................….…………....63

3.7 About……………..………………………..…………………………………………………….…………....63

3.8 camera Menu Control.……….……..…………………………………………………….…………....64

3.9 Help…………………………………………….……………………………………………………………....65

3.10 Resetting to the factory default settings……………….……………………………………....66

4. Appendix ……………………………………………………………..……………………………………….……67

4.1. Troubleshooting.…………………………..……………………………………………………….……67

4.2. Preventive Maintenance..………………………..........................….…………………….……68

4.3. Product Specification…..………………………………………………………………..….….....……69

5

1. Product Description

This manual applies to the VP Dome Network Camera.

The Network Camera supports the network service for an existing analog camera. An analog image entered can be monitored on a real-time screen regardless of distances and locations. By using its dedicated program, many users are able to have an access to the

Network Camera at once or a single user can monitor various network cameras at the same time. It also enables users to play, store and retrieve a monitoring image by using a PC. All the settings and real-time monitoring screens are also provided through an access to the web.

The Network Camera is a one-port video Camera including two-way audio, fully featured for security surveillance and remote monitoring needs. It is based on the DSP compression chip, and can digitize one analog video source and make it available on the network as real-time, full frame rate Motion JPEG and H.264 (or MPEG-4) video streams.

The Network Camera is equipped with RS-485 port for connecting third party PTZ systems.

The alarm input and alarm output can be used to connect various third party devices, such as, door sensors and alarm bells.

Components

The system comes with the following components:

VP Dome Network Camera unit Installation CD Installation Guide

Note: Check your package to make sure that you received the complete system, including all components shown above.

6

Key Features

• Brilliant video quality

The Network Camera offers the highly efficient H.264 video compression, which drastically reduces bandwidth and storage requirements without compromising image quality. Motion

JPEG is also supported for increased flexibility.

• Dual streams

The Network Camera can deliver dual video streams simultaneously at full frame rate in all resolutions up to D1 (720x480 in NTSC, 720x576 in PAL) using Motion JPEG and H.264 (or

MPEG-4). This means that several video streams can be configured with different compression formats, resolutions and frame rates for different needs.

• Image setting adjustment

The Network Camera also enables users to adjust image settings such as contrast, brightness and saturation to improve images before encoding takes place.

• Intelligent video capabilities

The Network Camera includes intelligent capabilities such as enhanced video motion detection. The encoder’s external inputs and outputs can be connected to devices such as sensors and relays, enabling the system to react to alarms and activate lights or open/close doors.

• Power over Ethernet

Support for Power over Ethernet (IEEE802.3af) enables the unit, as well as the analog camera that is connected to it, to receive power through the same cable as for data transmission. This makes for easy installation since no power outlet is needed.

• Audio support

The Network Camera also supports two-way audio.

• Improved Security

The Network Camera logs all user access, and lists currently connected users. Also, its full frame rate video can be provided over HTTPS.

• Camera

-. Superior image quality (560 TV Lines).

-. 0.3 Lux (Color) @ F1.2 Sensitivity.

-. C/CS, backfocus cam for easy adjustment.

-. Auto electronic shutter [1/60(1/50) ~ 1/100,000] and manual electronic shutter modes.

-. Full control via the OSD menu key on the side of the camera.

-. Auto and manual white balance modes.

-. BLC (Back Light Compensation)

-. Day&Night (Auto / Color / B/W)

-. AGC (Auto Gain Control)

-. Incredible noise reduction for picture quality & file size.

-. Sens-up (x2 ~ x128)

-. Privacy Zone 8 points.

-. MIRROR

-. VIDEO OUT(BNC)

7

2. Installation

For the operation of the Network Camera, it is necessary to connect a network cable for data transmission, power connection from supplied power adapter and connect a general analog camera. Depending on operation methods, it is possible to connect an alarm cable or audio cable additionally. For its fixation on different locations, please consult with an installer.

Overview

• Top View

NO

1

Lens

Name

2

Extension Cable

• Extension Cable

Description

Allows wide area to be monitored

26pin camera extension cable

8

NO

1

Wire Color

Red: AC24V/DC12V

White: AC24V/GND

Description

Main Power, 2pin terminal, DC12V/AC24V, max. 6.5W

2

3

Green: AC24V/DC12V

Black: AC24V/GND

Pink: Alarm In

Yellowish Green: GND

Yellow: AD Key

Brown: GND

Light Blue: Alarm Out

Gray: GND

Heater Power, 2pin terminal, max. 10Watt @ DC12V, max. 20Watt @ AC24V

Alarm Input, AD Key Input, Alarm Output:

6pin terminal.

4

Black

Ethernet,

RJ-45 port compatible with 10/100Mbps PoE.

Modular Jack

5

6

Black

Gray

Video Composite Output, BNC Jack

Audio line output, Stereo Jack

7

Black

Audio line input, Stereo Jack

Caution: Never aim the camera directly into the sun.

Base Installation

1. Make mounting holes and cable hole in the place (ceiling) to which this dome camera is installed using the supplied template sheet.

Warning: The total mass of the main unit is approx 1.3kg. Check whether the ceiling

to which the Dome Camera is installed is strong enough to hold the unit mass. If not, the Dome Camera could fall, causing injury.

2. Attach the safety wire for securing the dome camera to ceiling or structure not to fall.

3. Extract each wire through the cable hole, connect BNC cable and communication lines.

9

4. Unlock torx screws (4x) the dome cover and fix the dome case firmly with supplied mounting screws (4x), plastic anchors (4x), O-Rings (4x).

5. Adjust desired focus and scene by turning and moving the hemisphere by hand.

6. Lock the housing cover with torx screws (4x).

• Cable through the electrical box with the dome base

The housing can also be mounted on a 4s or 2s electrical box.

• Using the conduit knockout punched with the dome base

Remove the conduit knockout punched for the cable entry.

10

Heater Kit Installation

1. Place the heater element is slot “A”. Please ensure that the cables are facing upwards and the heater is pointing towards the Dome.

2. Place the PCB in slot “B”. Please ensure that the PCB is facing inside of the Dome with the connection blocks at the top.

3. Place the plug in the Socket “C” (J3) which is found on the controller board.

• Cheater (IF Applicable)

Power Supply

Power Consumption

Heater On

Heater Off

24VAC

20Watt at 41°F (5°C) at 59°F (15°C)

• Power

Use Certified/Listed Class 2 power source only.

12DCV

10Watt

11

Network Connection

The Network Camera supports the operation through the network. Therefore, it is necessary to connect a standard RJ-45 cable to it. Generally a cross-over cable is used for directly connection to PC, while a direct cable is used for connection to a hub.

IP Assignment

When a camera, Encoder or Decoder is first connected to the network it has no IP address.

So, it is necessary to allocate an IP address to the device with the “Smart Manager” utility on the CD.

1. Connect network camera / device to the network and power up.

2. Start SmartManager utility (All programs > NautilusClient16 > SmartManager), the main window will be displayed, after a short while any cameras connected to the network will be displayed in the list.

3. Select the camera on the list and click right button of the mouse. You can see the popup menu as below.

4. Select Assign IP. You cam see a Assign IP window.

Enter the required IP address.

12

The description of each field for the connection status follows.

: Available for connection to the camera

: Loading settings information of video after connecting the camera.

: Connectable to the camera but fixed security settings (password)

: Unavailable for connection to the camera (PC can not access relevant IP Address)

Note: Refer to NautilusClient16 User’s Manual for detailed information.

3. Operation

The Network Camera can be used with Windows operating system and browsers. The recommended browsers are Internet Explorer, Safari, Firefox and Google Chrome with

Windows.

Notes: To view streaming video in Microsoft Internet Explorer, set your browser to allow

ActiveX controls.

3.1 Access from a browser

1. Start a browser (Internet Explorer).

2. Enter the IP address or host name of the encoder in the Location/Address field of

your browser.

3. You can see a starting page. Click Live View or Setup to enter web page.

13

4. The encoder’s Live View page appears in your browser.

3.2. Access from the internet

Access from the internet Once connected, the Network Camera is accessible on your local network (LAN). To access the video encoder from the Internet you must configure your broadband router to allow incoming data traffic to the video encoder. To do this, enable the

NAT-traversal feature, which will attempt to automatically configure the router to allow access to the video encoder. This is enabled from Setup > System > Network > NAT.

For more information, please see NAT traversal (port mapping) for IPv4, on page 61.

3.3 Setting the admin password over a secure connection

To gain access to the product, the password for the default administrator user must be set. This is done in the “Admin Password” dialog, which is displayed when the network camera is accessed for the setup at the first time. Enter your admin name and password, set by the administrator.

Note: The default administrator username and password is “admin”. If the password is lost, the

Network Camera must be reset to the factory default settings. See “3.9 Resetting to the factory default settings”.

To prevent network eavesdropping when setting the admin password, this can be done via an encrypted HTTPS connection, which requires an HTTPS certificate (see note below).

14

To set the password via a standard HTTP connection, enter it directly in the first dialog shown below. To set the password via an encrypted HTTPS connection, see Setup >

System > Secutity > HTTPS, on page 51.

Note:

HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between web browsers and servers. The HTTPS certificate controls the encrypted exchange of information. The default administrator user cannot be deleted.

3.4 Live View Page

The live view page comes in eight screen modes like 704x480(576),

704x240(288), 352x240(288),

176x120(144), 640x480, 320x240, and 160x120. Users are allowed to select the most suitable one out of those modes. Please, adjust the mode in accordance with your PC specifications and monitoring purposes.

• General controls

The video drop-down list allows you to select a customized or preprogrammed video stream on the live view page. Stream profiles are configured under

Setup > Basic Configuration > Video & Image. See Basic Configuration, on page 27 for more information.

The resolution drop-down list allows you to select the most suitable one out of video resolutions to be displayed on live view page.

The protocol drop-down list allows you to select which combination of protocols and methods to use depends on your viewing requirements, and on the properties of your network.

• Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following buttons:

The Stop button stops the video stream being played.

Pressing the key again toggles the

start and stop. The Start button connects to the network camera or start playing a

video stream.

15

The Pause button pause the video stream being played.

The Snapshot button takes a snapshot of the current image. The location where the

image is saved can be specified.

The digital zoom activates a zoom-in or zoom-out function for video image on the live

screen.

The Full Screen button causes the video image to fill the entire screen area. No other

windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full

screen view.

The Manual Trigger button activates a pop-up window to manually start or stop the

event.

The Camera Menu button activates a pop-up window for camera menu control.

Use this scale to control the volume of the speakers.

Use this scale to control the volume of the microphone.

Use this scale to control the volume of the speakers and microphones.

• Camera Menu controls

If the Network Camera has been appropriately configured, the Live View page displays the controls available for the OSD menu.

Please see “3.8 Camera Menu Control for more information.

• Video and Audio Streams

The video encoder provides several images and video stream formats. Your requirements and the properties of your network will determine the type you use.

The Live View page in the video encoder provides access to H.264, MPEG-4 and Motion JPEG video streams, and to the list of available video streams. Other applications and clients can also access these video streams/images directly, without going via the Live View page.

16

3.5 Camera Setup (Analog)

3.5.1 Settings

Settings can be made using the 5 buttons located on the back of the camera.

Structure of menu setup

17

LENS (Selection)

This function is used to adjust the brightness of the screen.

1. When the SETUP menu is displayed on the screen, please position the arrow to point to LENS by using the UP and DOWN buttons.

2. Please select the type of the lens you wish to use by pressing the LEFT or RIGHT button.

Note: The brightness of the screen can be adjusted in DC mode.

The brightness can be adjusted within the range of 0 ~ 100.

The optimum level of brightness for the user can be achieved by adjustment.

EXPOSURE

The EXPOSURE menu is used to set the automatic light control method for this camera.

-. SHUTTER:

Select the shutter mode. (1/60(50), FLK~1/100,000 sec, x2~x256)

Can be changed while in shutter mode.

-. BRIGHTNESS:

Adjust BRIGHTNESS level (0~100).

Can be changed while in manual lens mode.

-. AGC:

Auto gain control (OFF/LOW/MIDDLE/HIGH)

-. SENSE-UP:

Use under very light condition for full color surveillance.

Select maximum Low-Shutter value. (x2 ~ x256)

-. BLC:

Sharpness subjects with backlight. (OFF/BLC/HBLC)

-. D-WDR:

Digital wide dynamic range. (OFF/INDOOR/OUTDOOR)

18

[BLC MODE]

WHITE BAL

The Screen color can be adjusted by using the WHITE BALANCE function.

-. AWB:

Wide range auto white balance mode.

-. AWC => SET:

Please press the ENTER button while the camera is directed at a piece of while paper to

obtain the optimum state under current illumination. If the environment including the

light source is changed, you have to adjust the wide balance gain.

-. MANUAL:

Manual mode. User can change R and B gain manually.

-. INDOOR:

Set the color temperature to 3200K

-. OUTDOOR:

Set the color temperature to 6300K

-. ATW:

Set the color temperature to 2500K to 9500K

[WHITE BAL MANUAL MODE]

19

DAY NIGHT

The DAT/NIGHT menu is used to configure the day and night related setting for this camera.

This camera can turn the IR(Infrared) filter on or off.

-. Mode: AUTO/EXT/BW/COLOR

[DAY/NIGHT AUTO MODE]

[DAY/NIGHT B/W MODE]

3DNR(Digital Noise Reduction)

You can configure the DNR(Digital Noise Reduction) related settings. If you press the Setup switch when ON is selected in 3DNR, the corresponding screen appears.

20

SPECIAL

1. CAM TITLE

-. A CAM TITLE : Camera Title

-. B 0123456789ABCD : Character Table

EFGHIJKLMNOPQRSTUVWXYZ

▶→←↑↓()−_▐ /=&:~,”

-. C ←→CLR POS END : ←, Move to left

:→, Move to right

: CLR, Erase all characters

: POS, Move the position of title

: END, Save and End

2. D-EFFECT

-. FREEZE: Select the real or still mode.

-. MIRROR: Reverse the screen in 3 modes selection. (OFF/MIRROR/V FLIP/ROTATION)

-. D-ZOOM: D-Zoom (x2~x32) / Adjust PAN/TILT

-. GAMMA: Adjust the luminance. (0.05~1.00)

-. NEGA/POSI: Select the negative or positive mode.

3. MOTION

-. AREA SELECT: Select MD area number.

-. AREA DISPLAY: Select MD ON/OFF.

-. LEFT/RIGHT: Adjust the location of the MD area with boundary LEFT and RIGHT.

-. WIDTH: Adjust width of MD area.

-. TOP/BOTTOM: Adjust the location of the MD area with boundary TOP and BOTTOM

-. HEIGHT: Adjust the height of MD area.

-. SENSITIVITY: Adjust sensitivity of MD area. (0~40)

-. MOTION VIEW: The screen displays with green dots. When a motion is detected in

the selected area, the green dots are displayed on the screen.

21

4. PRIVACY

-. AREA SELECT: Select MAK area number.

-. AREA DISPLAY: Select MASK ON/OFF.

-. LEFT/RIGHT: Adjust the location of the MASK area with boundary LEFT and RIGHT.

-. WIDTH: Adjust width of MASK area.

-. TOP/BOTTOM: Adjust the location of the MASK area with boundary TOP and BOTTOM.

-. HEIGHT: Adjust the height of MASK area.

-. COLOR: Select MASK color. (0~15)

[PRIVACY MODE]

5. SYNC: Select Internal or Line Lock mode.

-. INT: This mode is necessary for using the internal synchronization.

-. L/L: This mode is necessary for the operation of multi camera because it synchronizes

the camera phase by using the external signal (AC Signal).

-. PAHSE: Sync phase is adjustable in line lock mode.

6. LANGUAGE : You can change the OSD language using the LEF/RIGHT Setup switch.

ADJUST

1. SHARPNESS: Can be adjusted SHARPNESS of outlines. (0~31)

2. BLUE: Adjust B-GAIN value. (0~100)

3. RED: Adjust R-GAIN value. (0~100)

PRESET

1. FACTORY: Returns to the level which was set by the manufacturer.

EXIT

1. EXIT: Saves all the setting menus and then exits.

22

3.5.2 Lens Adjustment (Optical Vari-focal Lens)

Field of view: Adjust setting from Telephoto (T) to wide (W) field of view.

Focus: Adjust lens focus from near (N) to infinity (∞).

DC Auto IRIS Lens

Lens Type

Image Size

2.6 ~ 6mm

1/3” CCD

Focal Length 2.6~6mm±5%

Aperture

Ratio

Angular

1 : 1.6 ± 5%

DIAGONAL

Field of View

2.6mm: 134.6

6.0mm: 59.2

4 ~ 9mm

1/3” CCD

4~9mm±5%

1 : 1.6 ± 5%

DIAGONAL

4.0mm: 92.4

9.0mm: 39.2

23

2.8 ~ 12mm

1/3” CCD

6 ~ 50mm

1/3” CCD

2.8~12mm±5% 6.0~50mm±5%

1 : 1.4 ± 5%

2.8mm: 119.9

12mm: 28.8

1 : 1.6 ± 5%

DIAGONAL

6.0mm: 58.6

50mm: 7.1

3.6 Network Camera Setup

This section describes how to configure the network camera, and is intended for product

Administrators, who have unrestricted access to all the Setup tools; and Operators, who have access to the settings for Basic, Live View, Video & Image, Audio, Event, and System

Configuration.

You can configure the network camera by clicking Setup in the top right-hand corner of the

Live View page. Click on this page to access the online help that explains the setup tools.

When accessing the Network Camera for the first time, the “Admin Password” dialog appears. Enter your admin name and password, set by the administrator.

If the password is lost, the video encoder must be reset to the factory default settings. See

Resetting to the Factory Default Settings, on page 66.

24

3.6.1 Basic Configuration

3.6.1.1 Users

User access control is enabled by default. An administrator can set up other users, by giving these user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page, as described below:

The user list displays the authorized users and user groups (levels):

User Group Authority

Guest

Provides the lowest level of access, which only allows access to the

Live View page.

Operator

Administrator

An operator can view the Live View page, create and modify events, and adjust certain other settings. Operators have no access to System Options.

An administrator has unrestricted access to the Setup tools and can determine the registration of all other users.

• Enable anonymous viewer login: Check the box to use the webcasting features. Refer to

“3.6.2 Video & Image” for more details.

25

3.6.1.2 Network

The network camera support both IP version 4 and IP version 6. Both versions may be enabled simultaneously, and at least one version must always be enabled. When using IPv4, the IP address for the video encoder can be set automatically via DHCP, or a static IP address can be set manually. If IPv6 is enabled, the video encoders receive an IP address according to the configuration in the network router. There is also the option of using the

Internet Dynamic DNS Service. For more information on setting the Network, please see

Setup> System>Security>Network.

• IPv4 Address Configuration - Check this box to enable IPv4.

• Obtain IP address via DHCP - Dynamic Host Configuration Protocol (DHCP) is a protocol

that lets network administrators centrally manage and automate the assignment of IP

addresses on a network. DHCP is enabled by default. Although a DHCP server is mostly

used to set an IP address dynamically, it is also possible to use it to set a static, known IP

address for a particular MAC address.

• Use the following IP address - To use a static IP address for the Network Camera,

check the radio button and then make the following settings:

-. IP address - Specify a unique IP address for your Network Camera. (To check if the

IP address you intend to use is available or not, click the Test button)

-. Subnet mask - Specify the mask for the subnet the Network Camera is located on.

-. Default router - Specify the IP address of the default router (gateway) used for

connecting devices attached to different networks and network segments.

26

Notes:

1. DHCP should only be enabled if using dynamic IP address notification, or if your DHCP server can update a DNS server, which then allows you to access the Network Camera by name (host name). If DHCP is enabled and you cannot access the unit, you may have to reset it to the factory default settings and then perform the installation again.

2. The ARP/Ping service is automatically disabled two minutes after the unit is started, or

as soon as an IP address is set.

3. Pinging the unit is still possible when this service is disabled.

3.6.1.3 Video & Image

• Video Setting

-. Codec

The codec settings are separated into MPEG4 and H.264.

H.264 is a lso known as MPEG-4 Part 10. This is the new generation compression standard for digital video. This function offers higher video resolution than Motion JPEG or MPEG-4 at the same bit rate and bandwidth, or the same quality video at a lower bit rate.

-. Profile

There are 4 pre-programmed stream profiles available for quick set-up.

Choose the form of video encoding you wish to use from the drop-down list:

* H.264 MP(Main Profile):

Primarily for low-cost applications that requires additional error robustness, this profile is used rarely in videoconferencing and mobile applications, it does add additional error

27

resilience tools to the Constrained Baseline Profile. The importance of this profile is fading after the Constrained Baseline Profile has been defined.

* H.264 BP(Base Profile):

Originally intended as the mainstream consumer profile for broadcast and storage applications, the importance of this profile faded when the High profile was developed for those applications.

* MPEG4 SP(Simple Profile) is mostly aimed for use in situations where low bit rate and low resolution are mandated by other conditions of the applications, like network bandwidth, device size etc.

* MPEG4 ASP(Advanced Simple Profile)'s notable technical features relative to the Simple

Profile, which is roughly similar to H.263, including "MPEG"-style quantization, interlaced video, B pictures (also known as B Frames), Quarter Pixel motion compensation (Qpel), Global motion compensation (GMC).

-. Resolution

It enables users to determine a basic screen size when having an access through the Web

Browser or PC program. The screen size control comes in seven modes like

4CIF(704x480), 2CIF(704x240), CIF (352x240), QCIF(176x120), VGA(640x480),

QVGA(320x240), and QQVGA(160x120). Users can reset the selected screen size anytime while monitoring the screen on a real-time basis.

-. Bit-rate control

Limiting the maximum bit rate helps control the bandwidth used by the H.264 or MPEG-4 video stream. Leaving the Maximum bit rate as unlimited maintains consistently good image quality but increases bandwidth usage when there is more activity in the image.

Limiting the bit rate to a defined value prevents excessive bandwidth usage, but images are lost when the limit is exceeded.

Note that the maximum bit rate can be used for both variable and constant bit rates.

The bit rate can be set as Variable Bit Rate (VBR) or Constant Bit Rate (CBR). VBR adjusts the bit rate according to the image complexity, using up bandwidth for increased activity in the image, and less for lower activity in the monitored area.

CBR allows you to set a fixed target bitrate that consumes a predictable amount of bandwidth. As the bit rate would usually need to increase for increased image activity, but in this case cannot, the frame rate and image quality are affected negatively. To partly compensate for this, it is possible to prioritize either the frame rate or the image quality whenever the bit rate needs to be increased. Not setting a priority means the frame rate and image quality are equally affected.

28

-. Compression

When it is necessary to adjust a smooth transmission status according to network situations, users can increase the compressibility to carry out the network transmission stably. On the other hand, when it is necessary to maintain a detailed monitoring screen by enhancing the image quality, users can do so by decreasing the compressibility. In ease case, please adjust this function according to the network status and monitoring purposes. The default is 2000(Kbps).

-. Frame rate

Upon the real-time play, users should select a frame refresh rate per second. If the rate is high, the image will become smooth. On the other hand, if the rate is low, the image will not be natural but it can reduce a network load.

-. GOP size

Select the GOP(Group of Picture) size. If users want to have a high quality of fast image one by one, please decrease the value. For the purpose of general monitoring, please do not change a basic value. Such act may cause a problem to the system performance. For the details of GOP setting, please contact the service center.

• Image Setting

Sometimes the image size is large due to low light or complex scenery. Adjusting the maximum frame size helps to control the bandwidth and storage used by the Motion

JPEG video stream in these situations. Defining the frame size as Unlimited provides consistently good image quality at the expense of increased bandwidth and storage usage during low light. Limiting the frame size optimizes bandwidth and storage usage, but may give poor image quality. To prevent increased bandwidth and storage usage, the maximum frame size should be set to an optimal value.

-. JPEG Resolution

Same as the video settings.

-. JPEG Frame rate

Same as the video settings.

-. JPEG Quality

Select the picture quality. If users want to have a high quality of fast image one by one, please decrease the value. For the purpose of general monitoring, please do not change a basic value. Such act may cause a problem to the system performance.

When satisfied with the settings, click Save, or click Reset to revert to previously saved settings.

29

3.6.1.4 Audio

The Network Camera can transmit audio to other clients using an external microphone and can play audio received from other clients by attaching a speaker. The Setup page has an additional menu item called Audio, which allows different audio configurations, such as, full duplex, and simplex.

• Audio Setting

-. Audio Enable

Check the box to enable audio in the video stream.

-. Compression Type

Select the desired audio Compression format, G726.

-. Sample Rate

Select the required Sample rate (number of times per second the sound is sampled). The higher the sample rate, the better the audio quality and the greater the bandwidth required.

-. Sound Bit Rate

Depending on the selected encoding, set the desired audio quality (bitrate). The settings affect the available bandwidth and the required audio quality.

30

• Audio Input

Audio from an external microphone or a line source can be connected to the terminal I/O of the network camera.

-. Input Volume

If there are problems with the sound input being too low or high, it is possible to adjust the input gain for the microphone attached to the network camera.

• Audio Output

-. Full Duplex Enable

Check the box to enable Full Duplex mode. It means that you can transmit and receive audio (talk and listen) at the same time, without having to use any of the controls. This is just like having a telephone conversation.

This mode requires that the client PC has a sound card with support for full-duplex audio.

Uncheck the box enable Simplex mode. The simplex mode only transmits audio from the network camera to any web client. It does not receive audio from other web clients.

-. Output Volume

If the sound from the speaker is too low or high it is possible to adjust the output gain for the active speaker attached to the network camera.

When satisfied with the settings, click Save, or click Reset to revert to previously saved settings.

3.6.1.5 Date & Time

31

• Current Server Time

It displays the current date and time (24h clock). The time can be displayed in 12h clock format in the overlay (see below).

• New Server Time

Select your time zone from the drop-down list. If you want the server clock to automatically adjust for daylight savings time, select the “Automatically adjust for daylight saving time changes”.

From the Time Mode section, select the preferred method to use for setting the time:

-. Synchronize with computer time - sets the time from the clock on your computer.

-. Synchronize with NTP Server - the video encoder will obtain the time from an NTP

server every 60 minutes.

-. Set manually - this option allows you to manually set the time and date.

3.6.2 Video & Image

Basic

Refer to “3.6.1.3 Video & Image” for more details.

32

Privacy Masking

The privacy masking function allows you to mask parts of the video image to be transmitted. You can set up to eight privacy masks and the color of privacy masks is black.

The privacy masks are configured by Mask windows. Each window can be selected by clicking with the mouse. It is also possible to resize or delete, or move the window, by selecting the appropriate window at the mouse menu on the video screen.

To create a mask window, follow steps:

1. Click the right button of mouse to see the mouse menu.

2. Select New Privacy Mask in the mouse menu.

3. Click and drag mouse to designate a mask window area.

You can also modify or delete a motion index. Select an index and then, modify items or delete button. Select “Enable” to activate the privacy masking function.

33

Webcasting – Channel1

The network camera can stream live video to a website. Copy HTML code generated on the screen and paste it in page code of the website you want to display live video.

Note: To use webcasting service, the Enable Anonymous viewer login option must be checked. Refer to “3.6.1.1 Users” for more details.

34

3.6.3 Audio

Refer to “3.6.1.4 Audio” for more details.

35

3.6.4 Event

3.6.4.1 Event-In

On Boot

This is used to trigger the event every time the Network Camera start. Select “Enable” to activate the On Boot event.

36

Alarm In

Select “Enable” to activate the alarm event. The network camera support 1 alarm input ports.

-. Type - Choose the type of alarm you wish to use from the drop-down list.

-. Dwell Time - Set the dwell time an event lasts for the specified dwell time from the

point of detection of an alarm input.

37

Manual Trigger

This option makes use of the manual trigger button provided on the live view page, which are used to start or stop the event type manually. Alternatively the event can be triggered via the product's API (Application Programming Interface).

38

Motion

Motion detection is used to generate an alarm whenever movement occurs (or stops) in the video image. A total of 8 Motion and/or Mask windows can be created and configured.

Motion is detected in defined Motion windows, which are placed in the video image to target specific areas. Movement in the areas outside the motion windows will be ignored. If part of a motion window needs to be masked, this can be configured in a Mask window.

• Pre-Viewer

Motion detection windows are configured by Motion or Mask windows. Each window can be selected by clicking with the mouse. It is also possible to resize or delete, or move the window, by selecting the appropriate window at the mouse menu on the video screen.

To create a motion or mask window, follow steps:

1. Click the right button of mouse to see the mouse menu.

2. Select New Motion (or Mask) Window in the mouse menu.

3. Click and drag mouse to designate a motion area.

39

• Motion Detection Setting

The behavior for each window is defined by adjusting the Threshold and Sensitivity, as described below.

A motion index is a set of parameters describing Window Name, Type, Threshold,

Sensitivity, and Dwell Time. Window Types is one of Motion and Mask windows.

-. Threshold - Sets up the sensitivity for the motion detection.

-. Sensitivity - Sets up the sensitivity for the motion detection.

-. Dwell Time - Set the hold time an event lasts for the specified hold time from the

point of detection of a motion.

You can also modify or delete a motion index. Select an index and then, click the Modify or Delete button.

Select “Enable” to activate the motion window.

40

3.6.4.2 Event-Out

SMTP(E-Mail)

The Network Camera can be configured to send event and error email messages via SMTP

(Simple Mail Transfer Protocol).

SMTP(E-Mail) Setting

Select “Enable” to activate the SMTP operation.

-. Mail Server / Port -

Enter the host names (or IP addresses) and port numbers for

your mail server in the fields provided, to enable the sending of notifications and

image email messages from the camera to predefined addresses via SMTP.

-. Sender – Enter the email address to be used as the sender for all messages sent by

the Network Transmitter.

-. Interval - Represents the frequency of the email notification when an event occurs.

-. Aggregate events - Shows the maximum number of emails sent within each interval.

If your mail server requires authentication, check the box for Use authentication to log in to this server and enter the necessary information.

-. User Name / Password - Enter the User Name and Password as provided by your

network administrator or ISP (Internet Service Provider).

41

To ensure that the login procedure is performed as securely as possible when using

SMTP authentication, you must define the weakest authentication method allowed.

-. Login Method - Set the Weakest method allowed to the highest/safest method supported by the mail server. The most secure method is listed in the drop-down list:

Login / Plain

SMTP(E-Mail) Receiver

-. Receiver - Enter an email address. You can also register the e-mail address of recipients up to 8.

SMTP(E-Mail) Test

-. Receiver - Enter an email address and click the Test button to test that the mail servers are functioning and that the email address is valid.

FTP & JPEG

When the network camera detects an event, it can record and saves images to an FTP server. Images can be sent as e-mail attachments. Check the box to enable the service.

• FTP Setting

-. Server - Enter the server's IP address or host name. Note that a DNS server must be specified in the TCP/IP network settings if using a host name.

-. Port - Enter the port number used by the FTP server. The default is 21.

-. Use passive mode - Under normal circumstances the Network Camera simply requests the target FTP server to open the data connection. Checking this box issues a PASV command to the FTP server and establishes a passive FTP connection; whereby the

Network Camera actively initiates both the FTP control and data connections to the target server. This is normally desirable if there is a firewall between the camera and the target

FTP server.

42

-. Remote directory - Specify the path to the directory where the uploaded images will be stored. If this directory does not already exist on the FTP server, there will be an error message when uploading.

-. User name / Password - Provide your log-in information.

JPEG Setting

-. Pre-event - A pre-event buffer contains images from the time immediately preceding the event trigger. These are stored internally in the server. This buffer can be very useful when checking to see what happened to cause the event trigger.

Check the box to enable the pre-trigger buffer, enter the desired total length in seconds, minutes or hours, and specify the required image frequency.

-. Post-event - This function is the counterpart to the pre-trigger buffer described above and contains images from the time immediately after the trigger. Configure as for preevent.

-. Prefix file name - This name will be used for all the image files saved. If suffixes are also used, the file name will take the form <prefix>.<suffix>.<extension>

-. Additional suffix - Add either a date/time suffix or, a sequence number - with or without a maximum value

HTTP Server

When the network camera detects an event, HTTP Server is used to receive uploaded image files and/or notification messages. Check the box to enable the service.

HTTP Server Setting

-. Name - The name of the HTTP event server. Use a descriptive name.

-. URL - The network address to the server and the script that will handle the request.

For example:

http://192.168.12.244/cgi-bin/upload.cgi

-. User name/Password - Provide your log-in information.

43

HTTP Server Test

When the setup is complete, the connection can be tested by clicking the Test button.

Alarm Out

When the network camera detects an event, it can control external equipment connected to its alarm output port. Check the box to enable and then select either:

-. Enable – When you select “Enable alarm out”, the output will be activated for as long

as the event is active.

44

Audio Alert

When the network camera detects an event, it can output a predefined audio data to external speaker. Check the box to enable the service.

Audio Alert Setting

To use the audio alert with the Network Transmitter, an audio data file made by user must be uploaded from your PC. Provide the path to the file directly, or use the Browse button to locate it. Then click the Upload button.

An audio file for Audio Alert can be made by Audio Recorder tool in the NautilusClient16 software.

Audio Alert Test

When the setup is complete, the audio output can be tested by clicking the Test button.

To remove an audio file, select index and click the Remove button.

Note: For a proper operation of Audio Alert, you must enable “full duplex” in Audio setting page.

45

Audio Recorder

To use Audio Recorder tool to make an audio file for Audio Alert function, you must install the NautilusClient16 on the installation CD at first.

The NautilusClient16 program (All Programs>NautilusClient16> NautilusClient16) in your PC, the main window will be displayed as below.

Click “Tool” in the menu of the main window and select Audio Recorder to start Audio

Recorder. Audio Recorder window will be appeared.

The description of each button in the ARecorder window follows.

Open: Open an audio file.

Capture: Capture audio from the microphone in your PC.

Save: Save a captured file to your PC. (PCM format)

Encode: Encode a current capture file or opened PCM file to G.726 file for Audio Alert.

Play: Play a current audio file.

Stop: Stop playing audio.

46

Procedures to make an audio file in G.726 format for Audio Alert.

1. Connect the microphone in your PC.

2. Click the Capture button and talk to the microphone to record the audio or voice.

You can record up to 30 seconds. Click the Stop button to stop on capturing.

3. Click the Save button and then set the file name to save a current capture file with

PCM format.

If you don’t need to make any PCM file, skip this step and then go to the step 5 directly.

4. Click the Open button and then select the file name to open an audio file in PCM

format.

5. Click the Encode button to encode a current audio file to G.726 format for Audio Alert.

Set the file name and encode parameters.

Caution: All parameters must be synchronized with ones in audio setting page of network devices for a proper operation.

47

3.6.4.3 Event Map

The event map allows you to change the settings and establish a schedule for each event trigger from the Network Camera. You can register the event map up to max. 15.

Click Add button to make a new event map and you can see a popup window as below.

48

General

Enter the name for a new event map.

Event In

Select an event type in the drop down list.

Event Out

-. E-mail: Select email addresses you want to send via email that an event has occurred.

-. FTP: Select checkbox beside FTP to record and saves images to an FTP server when an

event has occurred.

-. HTTP Server: It sends notification messages to an HTTP server that listens for these.

The destination server must first be configured on the Event In page. Enter a message you want to send.

-. Audio Alert: Select a Audio alert file the Network Transmitter output when audio alert

event triggered. The Audio alert file must first be configured on the Event In page.

3.6.5 System

3.6.5.1 Information

You can enter the system information. This page is very useful when you refer device information after installation.

Device Name Configuration

Enter the device name.

Location Configuration

Enter the location information. You can enter that by four.

49

3.6.5.2 Security

Users

User access control is enabled by default, when the administrator sets the root password on first access. New users are authorized with user names and passwords, or the administrator can choose to allow anonymous viewer login to the Live View page, as described below:

User Setting

Check the box to enable anonymous viewer login to the Network Camera without the user account. When using the user account, users have to try log-in at every access.

• User List Setting

This section shows a registered user account. Enter a user name and password to be added, and register them by pressing the “Add” button. You can see the pop-up window as below.

50

HTTPS

For greater security, the Network Camera can be configured to use HTTPS (Hypertext

Transfer Protocol over SSL (Secure Socket Layer)). That is, all communication that would otherwise go via HTTP will instead go via an encrypted HTTPS connection.

• HTTPS Connection Policy

Choose the form of connection you wish to use from the drop-down list for the administrator, Operator and Viewer to enable HTTPS connection (set to HTTP by default).

-. HTTP

-. HTTPS

-. HTTP & HTTPS

• Upload Certificate

To use HTTPS for communication with the Network Camera, An official certificate issued by a CA (Certificate Authority) must be uploaded from your PC. Provide the path to the certificate directly, or use the Browse button to locate it. Then click the Upload button.

Please refer to the home page of your preferred CA for information on where to send the request. For more information, please see the online help.

51

IP Filtering

Checking the Enable IP address filtering box enables the IP address filtering function.

Up to 256 IP address entries may be specified (a single entry can contain multiple IP addresses). Click the Add button to add new filtered addresses.

When the IP address filter is enabled, addresses added to the list are set as allowed or denied addresses. All other IP addresses not in this list will then be allowed or denied access accordingly, that is, if the addresses in the list are allowed, then all others are denied access, and vice versa. See also the online help for more information.

Note that users from IP addresses that will be allowed must also be registered with the appropriate access rights (Guest, Operator or Administrator). This is done from Setup>

System>Security>Users.

52

3.6.5.3 Date & Time

• Current Server Time

It displays the current date and time (24h clock). The time can be displayed in 12h clock format in the overlay (see below).

New Server Time

Select your time zone from the drop-down list. If you want the server clock to automatically adjust for daylight savings time, select “Automatically adjustment for daylight saving time changes”.

From the Time Mode section, select the preferred method to use for setting the time:

-. Synchronize with computer time - sets the time from the clock on your computer.

-. Synchronize with NTP Server - the video encoder will obtain the time from an NTP

server every 60 minutes.

-. Set manually - this option allows you to manually set the time and date.

Note: Note that if using a host name for the NTP server, a DNS server must be configured under TCP/IP settings.

53

3.6.5.4 Network

Setting in regard to network can be executed. Settings for IP, DNS, Host Name, Port, and

ARP/Ping can be established, along with setting for DDNS, uPnP, QoS, and SNMP.

54

Basic

• IP Address Configuration:

-. Obtain IP address via DHCP - Dynamic Host Configuration Protocol (DHCP) is a protocol

that lets network administrators centrally manage and automate the assignment of IP

addresses on a network. DHCP is enabled by default. Although a DHCP server is mostly

used to set an IP address dynamically, it is also possible to use it to set a static, known

IP address for a particular MAC address.

-. Use the following IP address - To use a static IP address for the Network Camera,

check the radio button and then make the following settings:

* IP address - Specify a unique IP address for your Network Camera.

* Subnet mask - Specify the mask for the subnet the Network Camera is located on.

* Default router - Specify the IP address of the default router (gateway) used for

connecting devices attached to different networks and network segments.

• IPv6 Address Configuration

Check this box to enable IPv6. Other settings for IPv6 are configured in the network router.

• DNS Configuration

DNS (Domain Name Service) provides the translation of host names to IP addresses on

your network.

-. Obtain DNS Server via DHCP - Automatically use the DNS server settings provided by

the DHCP server. Click the View button to see the current settings.

-. Use the following DNS server address to enter the desired DNS server by specifying the

following:

* Domain name - enter the domain(s) to search for the host name used by the Network

Camera. Multiple domains can be separated by semicolons (;). The host name is

always the first part of a Fully Qualified Domain Name, for example, myserver is the

host name in the Fully Qualified Domain Name myserver.mycompany.com

where

mycompany.com is the Domain name.

* DNS servers - enter the IP addresses of the primary and secondary DNS servers.

• Host Name Configuration

-. Host Name – enter the host name to be used as device information in the client software or SmartManager.

• Services

-. HTTP port: Enter a port to receive a service through the HTTP. Default Port Number is

‘80’.

-. RTSP port: Enter a port to receive a service through the RTSP. Default Port Number is

‘7070’.

-. PTZ port: Enter a port to control the Pan/Tilt/Zoom. Default Port Number is ‘7000’.

• ARP/Ping Setting

-. Enable ARP/Ping setting of IP address - The IP address can be set using the ARP/Ping

method, which associates the unit's MAC address with an IP address. Check this box to

enable the service.

Leave disabled to prevent unintentional resetting of the IP address.

55

DDNS

Internet DDNS(Dynamic Domain Name Service)

When using the high-speed Internet with the telephone or cable network, users can operate the Network Camera even on the floating IP environment in which IPs are changed at every access.

Users should receive an account and password by visiting a DDNS service like http://www.dyndns.com/ , or http://www.cctv-network.co.kr/ .

-. Enable DDNS - Check to get DDNS service to be available.

* DDNS Server: Select the DDNS server.

* Registered host: Enter an address of the DDNS server.

* Username: Enter an ID to access to the DDNS server.

* Password: Enter a password to be used for accessing the DDNS server.

* Confirm: Enter a password again to confirm it.

* Maximum time interval: Set a time interval to synchronize with the DDNS server.

Select an item in the interval drop-down list.

* Register local network IP address: Click this box to register the camera IP address to

DDNS server in case that the network camera and Client are in the local network environment. You don’t need to click this box in case that the Client is not in the local network environment.

56

RTP

Have a setting for sending and receiving an audio or video on a real-time basis. These settings are the IP address, port number, and Time-To-Live value to use for the media stream(s) in multicast H.264 format. Only certain IP addresses and port numbers should be used for multicast streams. For more information, please see the online help.

Port Range

-. Start port - Enter a value between 1024 and 65532

• Multicast

This function is for sending Video and Audio to Multicast group.

-. Enable Multicast - Check the box to enable multicast operation.

-. Multicast destination IP - Enter an IP between 224.0.0.0 and 239.255.255.255. Although

it is empty, an IP will be entered automatically.

-. RTP port: Enter a value between 1024 and 65532.

-. RTP TTL: Enter a value between 1 and 255. If a network status is smooth, enter a lower

value. On the other hand, if a network status is poor, enter a higher value. When there

are many Network Cameras or users, a higher value may cause a heavy load to the

network. For a detailed setting, please consult with a network manager.

57

UPnP

The Network Camera includes support for UPnP™. UPnP™ is enabled by default, and the

Network Camera then is automatically detected by operating systems and clients that support this protocol.

Note : UPnP™ must be installed on your workstation if running Windows XP. To do this, open the Control Panel from the Start Menu and select Add/Remove Programs. Select

Add/Remove Windows Components and open the Networking Services section. Click Details and then select UPnP™ as the service to add.

58

QoS

Quality of Service (QoS) provides the means to guarantee a certain level of a specified resource to selected traffic on a network. Quality can be defined as a maintained level of bandwidth, low latency, and no packet losses.

The main benefits of a QoS-aware network are:

-. The ability to prioritize traffic and thus allow critical flows to be served before flows with lesser priority.

-. Greater reliability in the network, thanks to the control of the amount of bandwidth an application may

use, and thus control over bandwidth races between applications.

• DSCP Settings

For each type of network traffic supported by your network video product, enter a DSCP

(Differentiated Services Code Point) value. This value is used to mark the traffic’s IP header. When the marked traffic reaches a network router or switch, the DSCP value in the IP header tells the router or switch which type of treatment to apply to this type of traffic, for example, how much bandwidth to reserve for it. Note that DSCP values can be entered in decimal or hex form, but saved values are always shown in decimal.

The following types of traffic are marked:

-. Live Stream DSCP:

-. Event/Alarm DSCP:

-. Management DSCP:

59

• Auto Traffic Control

Set a limitation on user network resources by designating the maximum bandwidth.

-. Maximum bandwidth - In case of sharing other network programs or equipment, it is

possible to set a limitation on the maximum bandwidth in the unit of Mbit/s or kbit/s.

-. Auto frame rate - Selected if not influenced by a network-related program or

equipment without a limitation on the network bandwidth.

NAT Traversal

A broadband router allows devices on a private network (LAN) to share a single connection to the Internet. This is done by forwarding network traffic from the private network to the

“outside”, that is, the Internet. Security on the private network (LAN) is increased since most broadband routers are pre-configured to stop attempts to access the private network

(LAN) from the public network/Internet.

Use NAT traversal when your network cameras are located on an intranet (LAN) and you wish to make it available from the other (WAN) side of a NAT router. With NAT traversal properly configured, all HTTP traffic to an external HTTP port in the NAT router is forwarded to the network camera.

Notes:

-. For NAT traversal to work, this must be supported by the broadband router.

-. The broadband router has many different names:

“NAT router”, “Network router“, Internet Gateway”, “Broadband sharing device” or

“Home firewall” but the essential purpose of the device is the same.

60

• NAT traversal Settings

-. Enable - when enabled, the network transmitters attempt to configure port mapping in

a NAT router on your network, using UPnP™. Note that UPnP™ must be enabled in the

Network Camera (see System>Network>UPnP).

* automatic setting: The Network Camera automatically search for NAT routers on

your network.

* manual setting: Select this option to manually select a NAT router and enter the

external port number for the router in the field provided.

Notes:

-. If you attempt to manually enter a port that is already in use, an alert message will be

displayed.

-. When the port is selected automatically it is displayed in this field. To change this enter

a new port number and click Save.

3.6.5.5 Language

It will be able to select a user language. The type of language it will be able to select is the

English, the French, the German, the Spanish and the Italian.

61

3.6.5.6. Maintenance

Maintenance Server

-. Restart - The unit is restarted without changing any of the settings. Use this method if

the unit is not behaving as expected.

-. Restore - The unit is restarted and most current settings are reset to factory default

values. The settings that are not affected are:

- the boot protocol (DHCP or static)

- the static IP address

- the default router

- the subnet mask

- the system time

-. Default - The default button should be used with caution. Pressing this will return all of

the Network Camera's settings to the factory default values (including the IP

address)

• Update Server

Carry out the upgrade by importing an upgrade file and pressing the ‘Upgrade’ button.

During the upgrade, do not turn off the power of the Network Camera. And try an access again after waiting five minutes or longer.

• Backup

Save a setting value that users enter to the Network Camera, to a user PC.

• Restore

Import and apply a setting value saved to a user PC.

62

Note: Backup and Restore can only be used on the same unit running the same firmware.

This feature is not intended for multi-configurations or for firmware upgrades.

3.6.5.6 Support

The support page provides valuable information on troubleshooting and contact information, should you require technical assistance.

• Logs

The network Camera support system log information. Click “System Log” button to get the log data.

• Update Server

-. Server Report – Click the “Server Report” button to get the important information about

the server’s status and should always be included when requesting support.

-. Parameter List – Click the “Parameter List” button to see the unit’s parameters and their

current settings.

3.7 About

The following website will provide the support information for the Network Camera information and operation.

63

3.8 Camera Menu Control

You can control camera menu in the live screen. Press the the live screen to activate the camera manual panel.

button on the left top in

Camera Menu Panel

64

3.9 Help

The Help information window will be provided as a popup window so that users can open and read it without a need for log-in. It will offer a description on setting and Help page by which users can manipulate the Network Camera without a reference to the manual.

65

3.10 Resetting to the factory default settings

To reset the Network Camera to the original factory settings, go to the Setup > System >

Maintenance web page (described in “3.6.5.6 Maintenance”) or use the control button on the network camera, as described below:

• Using the Reset Button

Follow the instructions below to reset the Network Camera to the factory default settings using the Reset Button.

1. Switch off the Network Camera by disconnecting the power adapter.

2. Open the lens cover.

3. Press and hold the Control Button on the board with your finger while reconnecting the

power.

4. Keep the Control button pressed during about 2 seconds.

5. Release the Control Button.

6. The network camera resets to factory defaults and restarts after completing the factory

reset.

7. Close the lens cover.

CAUTION: When performing a Factory Reset, you will lose any settings you have saved.

66

4. Appendix

4.1 Troubleshooting

Troubleshooting if problems occur, verify the installation of the Network Camera with the instructions in this manual and with other operating equipment. Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information.

P r r o b l l e m s / S y m p t t o m s

A r r e a t t o C h e c k

Verify that power is connected to all pieces of equipment in

No video

Poor video quality. the system.

Verify that the power switches are in the ON position.

Check the video connections.

Check that the BNC connectors are inserted properly.

Check the voltage level of the Network Camera.

Cable for video is shielded.

Camera number does not match the number on PC Program or Web browser.

Check the camera ID of the 1CH Network Camera.

Check PTZ setting on the PC Program and Web browser.

Frame rate decrease.

A connection is cut-off at short intervals.

Change current value more lower resolution, compression rate and frame rate.

Check network traffic and contact with network administrator.

67

4.2 Preventive Maintenance

Preventive maintenance allows detection and correction of minor that faults before they become serious and cause equipment failure.

Every three-month, perform the following maintenance.

1. Inspect all connection cables for deterioration or other damage.

2. Clean components with a clean damp cloth.

3. Verify that all the mounting hardware is secure.

68

K

T

W

O

R

N

E

F

I

O

N

U

N

C

T

4.3 Product Specification

Main Item

Image sensor

Total pixels

Scanning system

Scanning frequency

Sync. system

Resolution

Min. illumination

S/N ratio

DNR

(Digital Noise Reduction)

D-WDR

(

Digital Wide Dynamic Range

)

BLC

(Back Light Composite)

Day & Night (True D/N)

MD (Motion Detection)

Sense-Up

(Low Shutter Speed)

PM (Privacy Masking)

WB (White Balance)

AGC

(Auto White Balance)

Electric Shutter Speed

Sharpness

Flip

Effect

Setup Method

OSD Language

Video Compression

Video Resolutions

Frame Rate

Video Streaming

Audio Compression

Audio Streaming

Protocol

Security

Max. Connection

API Programming

Interface

Alarm Triggers

NTSC

1/3” SONY Super HAD CCD

PAL

811(H)x508(V)

2:1 interlace

795(H)x596(V)

15.734Khz(H)x59.94Hz(V) 15.625Khz(H)x50Hz(V)

Internal / Line lock

560 TV lines

Color: 0.25 Lux, B/W: 0.01 Lux (Sense-Up: Off)

50dB (AGC Off)

On/Off (Adjustable Gain)

On (Indoor/Outdoor)/Off

BLC/HSBLC/OFF Adjustable Size & Gain

Color/B/W/Auto(Filter auto change)/EXT

On/Off ( 4 Programmable zone)

Auto/Off (Selectable limit 2x ~ 256x)

On/Off ( 8 Programmable zone)

AWB/ATW/AWC/Manual/Indoor/Outdoor

On(Low/Middle/High)/Off

Auto/Flickerless/Manual(256x, 1/60 ~ 1/100,000)

On/Off(Level adjustable)

Horizontal/Vertical/Rotate

D-Zoom x32(Pan/Tilt)/Nega/Freeze

OSD Setup menu

English/Korean/Japanese

Motion JPEG

MPEG-4 Part2

H.264 (MPEG-4 Part 10)

Profiles: H.264 MP and BP, MPEG-4 ASP and SP

160x120 ~ 704x480 160x120 ~ 704x576

Up to 30/25fps[NTSC/PAL] @ all resolutions

Simultaneously H.264(or MPEG-4) and MJPEG

Controllable Frame Rate and Bandwidth VBR/CBR

H.264 and MPEG-4

G.726 ADPCM 40kbps~16kbps

2 Way

TCP/IP, UDP, IPv4/v6, HTTP, HTTPS, QoS, FTP, SNMP, uPnP, RTP, RTSP, RTCP, DHCP, ARP

Multi-user authority, HTTPS, IP Filtering, Privacy Zone

10

API Supported,

Open Platform Compatible: Milestone, ONVIF

Motion Detection, External Input, Manual Trigger

69

O

R

K

N

E

T

W

G

E

N

E

R

A

L

Alarm Events

Video Buffering

Motion Detection

Network Time

Synchronization

Software Reset

Factory Reset

Auto Recovery

Installation Tool

Upgrade

Alarm In/Out

Ethernet

External I/O Terminals

Video Output

Audio In/Out

Buttons

Lens mount

Lens

Operating Temperature

Operation Humidity

Power Consumption

File upload via FTP and HTTP

Notification via E-mail, HTTP and TCP

External Output activation

Audio Alert activation

Pre and Post Alarm

Yes, Max 8 window

Yes

Yes, Button/Web browser

Yes

Yes, SmartManager

Yes, Web browser/SmartManager

1/1

RJ-45 10BASE-T/100BASE-TX PoE

AC24V/DC12V, Alarm In/Out,

BNC, 1.0 Vp-p (75ohm, composite)

1/1, Stereo Jack

5 key, Up/Down/Left/Right/Enter

Fixed Mount

2.6~6mm, 4~9mm, 2.8~12mm, 6~50mm D/N Varifocal (DC AI)

0°C ~ 45°C

0~90% (non-condensing)

AC24/DC12V max. 6.5watt, Power over Ethernet IEEE

802.3af Class2/3

External Dimension

(Φ x H)

Φ

150 x 125mm [Bubble Diameter

Φ

]

Unit Weight

Approval

990g

FCC, CE, UL, MIC

System Requirement for Web Browser

Operating System: Microsoft Windows 98, Microsoft Windows ME, Microsoft Windows

2000, Microsoft Windows XP, or Microsoft Windows Vista

CPU: Over Pentium IV 2.4Ghz, 512MB RAM, 10GB free disk or higher

VGA: AGP, Video RAM 32MB or higher (1024x768, 24bpp or higher)

70

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement