DTS XR1200 WASH Fresnel User manual
Add to my manuals28 Pages
DTS XR1200 WASH Fresnel is a moving head fixture that combines powerful illumination with a versatile feature set for professional applications. It boasts a 1200W Philips MSR Gold Fastfit lamp, motorized zoom (20°- 45°), rotating indexable beam shaper (0°-180°), frost filter, CMY color generation system, color wheel with linear selection, and electronic ballast. With its impressive output, the XR1200 WASH Fresnel excels at illuminating objects and large backgrounds with a wide array of colors and effects, making it ideal for concerts, shows, tours, events, clubs, and other venues.
advertisement
XR1200 WASH
03.MW005.EB.PC.L
XR1200 WASH PC
03.MW005.EB.L
XR1200 WASH FRESNEL
User’s Manual Rel 3.0
GB
D.T.S. Illuminazione srl - ITALY http://www.dts-lighting.it
Made in Italy
2
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso scritto della D.T.S.
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S. non assume alcuna responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de ningún tipo sobre la utilización o sobre la aplicació n de los productos o de los circuitos descritos.
3
INDEX:
1- SYMBOLS
2- GENERAL WARNING
3- GENERAL WARRANTY CONDITION
4- TECHNICAL FEATURES
4
4
4
5
5- ACCESSORIES 6
6- IMPORTANT SAFETY INFORMATION
6.1 Fire prevention
6.2 Prevention of electric shock
6.3 Protection against ultraviolet radiation
6.4 Safety
6.5 Level of protection against the penetration of solid and liquid matter
7
7- MOUNTING THE LAMP
3.1 Lamp alignment
8
8- VOLTAGE AND FREQUENCY
9
9- INSTALLATION
9.1 Safety cable
9
9.2 Protection against liquids
9.3 Movement 10
9.4 Risk of fire
9.5 Forced ventilation
9.6 Ambient temperature
10- MAINS CONNECTION
10.1 Protection
11- DMX SIGNAL CONNECTION
11.1 DMX Addresses
11.2 Selecting the DMX address
12- FIRMWARE UPDATING
10
11
12
13- DISPLAY FUNCTIONS
13
14- ERROR MESSAGES 16
15- HIDDEN MENU 17
16- OPENING THE PROJECTOR HOUSING
17- PERIODIC CLEANING
17.1 Lenses and reflectors
17.2 Fans and air passages
18
18- PERIODIC CONTROLS
19- DMX PROTOCOLS 19
20-COLOUR WHEEL 24
21- 8 MOTORS CONTROL CARD 25
22- PAN & TILT CARD 26
23-CABLES RESEND CARD
24-DISPLAY CARD
25- LAMP ON-OFF CONTROL CARD
4
1- SYMBOLS
Graphic symbols used on this manual
THIS SYMBOL INDICATES A HOT SURFACE
THIS SYMBOL INDICATES ELECTRIC SHOCK RISK
!
THIS SYMBOL INDICATES GENERAL RISK
F
THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON
INFLAMMABLE SURFACES”
UV
THIS SYMBOL MEANS “RADIATION FROM THIS LAMP
CAN CAUSE DAMAGE TO EYES AND SKIN”
THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO
BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT
2M
2- GENERAL WARNING
Read the instruction contained in this user manual carefully, as they give important information regarding safety during installation , use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or experienced person.
Always disconnect the device from the mains before replacing the lamp.
The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.
The device must always be equipped with an efficient ground connection.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for
36 months
from the date of purchase against manufacturing material defects.
5
4- TECHNICAL FEATURES
The XR1200 WASH is a moving head fitted with a Philips MSR Gold 1200W Fastfit discharge lamp
(95.000 Lumens) combined with a dichroic parabolic reflector.
The XR1200 WASH incorporates motorized zoom (20°- 45° FRESNEL LENS MODEL / 9°-19° PC LENS
MODEL), rotating indexable beam shaper (0°-180°), frost filter, CMY colour generation system, colour wheel with linear selection for perfect 2-colour beams (6 dichroic filters + 2 colour conversion filters
3.200°K and 5.600°K +open) and electronic ballast. The XR1200 WASH also includes a new Pan / Tilt locking system with recessed buttons. The XR1200 WASH is particularly suitable for all professional applications, both mobile (concerts, shows, tours, special events) and fixed (clubs and other venues), requiring a light with extremely luminous output capable of illuminating objects and large backgrounds with an endless variety of colours.
XR 1200 WASH FRESNEL (Cod. 03.MW005.EB.L)
XR 1200 WASH PC (Cod. 03.MW005.EB.PC.L)
Electronic ballast 90-260V 50/60 Hz• Black colour
All models are also available in white colour
Lamp
Lamp: Philips MSR Gold 1200 Fastfit
.
Automatic switching on of lamp in case of accidental switching off
Lamp on/off via DMX; reset via DMX.
Optical group
XR 1200 WASH FRESNEL: 27.000 Lux at 5 m (20°). Fresnel lens Ø 200 mm.
XR 1200 WASH PC: 104 9
Borosilicate dichroic parabolic reflector
Zoom
XR 1200 WASH FRESNEL: Motorized zoom (20°- 45°)
XR 1200 WASH PC: 9
Dimmer / shutter / strobo
Linear dimmer
,
Shutter
,
Strobe from 0,85 flash/sec to 10 flash/sec
Power saving mode (the lamp dims to 50% six seconds after shutter closure)
Colours
CMY color generation system with 3 palettes + colour wheel (6 colours + 2 colour conversion filters + open) with linear selection for perfect 2-colour beams
.
Color change with blackout sync
Effects
Rotating and indexable beam shaper (0°-180°)
Pan / Tilt
Pan 540° (2,9 sec.). Tilt 270° (1,8 sec.). 16-bit resolution
8 selectable speed ranges (8 selectable pan/tilt speeds); extremely smooth and precise movements even at the highest speeds. Pan / Tilt locking system with recessed buttons. Automatic Pan/Tilt repositioning in case of knocks
16 DMX channels
Internal operating system updatable via DMX
INTERFACE
LCD backlit graphic display (128x64)
Connections
4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik
Power supply
Electronic ballast: 90 - 260 V (50/60 Hz); power consumption: 1320 W
Thermal
Operating ambient temperature: -10° / 40°
Weight
38 Kg (Electronic Ballast)
6
4- TECHNICAL FEATURES
Dimensions
Packaging Dimensions (LxWxH)
580 x 490 x 800 mm
Weight: 43 Kg
430 mm
Unit Dimensions (LxWxH)
500 x 490 x 685mm
Weight: 38 Kg
500 mm
270°
490 mm
460 mm
5- ACCESSORIES
As standard
•1 x MSR Gold 1200 Fastfit lamp
•1 x POWERCONN male cable connector (cod. 0520P014)
•1 x XLR 5 Pins male cable connector (cod. 0508B028)
•1 x XLR 5 Pins female cable connector (cod. 0508B027)
•2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
•1 x FROST filter (cod. 0506V016 )
• User’s manual
Optional (on request)
• Wireless DMX receiver card (cod. 03.LA.012)
• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)
• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)
• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)
• Omega clamp with “Fast Lock” connection 1⁄4 turn (cod. 02K00467)
• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)
7
XR1200 WASH
6- IMPORTANT SAFETY INFORMATION
6.1 Fire prevention:
XR1200 WASH uses a Philips MSR Gold 1200 Fastfit lamp.
The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 MT.
F
-Minimum distance from the closest illuminable surface: 2 MT.
2M
-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
6.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head, including lamp replacement.
-The level of technology present in the XR1200 requires the assistance of specialised personnel for all servicing. Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
6.3 Protection against ultraviolet radiation:
UV
-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
6.4 Safety:
!
-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should not exceed 40°C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
6.5 Level of protection against the penetration of solid and liquid matter:
!
-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid matter is IP 20.
For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:
• Raincover for XR1200 base (top) (cod. 03.MA009)
• Raincover for XR1200 base (bottom) (cod. 03.MA010)
8
XR1200 WASH
7- MOUNTING THE LAMPS
Warning: Switch off the unit before replacing the lamp.
Philips MSR Gold 1200 Fastfit
Power 1200W
Luminous flux 95,000 lm
Colour temperature 6.300°K
Lampbase PGJX50
Rated life 750 hours
1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .
Photo 1 Photo 2 Photo 3 Photo 4
2) Insert the lamp (photo2).
3)Rotate the lamp 1/4 turn clockwise (photo 3 and 4).
The lamp used on XR1200 is made in quartz glass and should be handled with care. Always follow the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided in the lamp's packaging. The PGJX50 lamp socket is not symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat the procedure.
4) Replace the metal cover and tighten the screws A,B,C, which where previously removed.
WARNING: Never look directly at the lamp when it’s lit.
Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.
UV
7.1 Lamp alignment
Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic filters and other components inside the unit. The lamp alignment is also essential to obtain the maximum unifirmity and luminous performance by the projection.
Lamp
Alignment
Photo 5 Normal Hot Spot
1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the 3 adjusters X, Y and
Z (photo 5) until you achieve a uniform flat field.
When the lamp is correctly optimized, you will have an evenly projected light beam, with no shadows or zones wich are brighter than others.
9
8VOLTAGE AND FREQUENCY
The XR1200 with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.
XR1200 WASH
9INSTALLATION
XR1200 may be either floor or ceiling mounted.
For floor mounting installations, the XR1200 is supplied with four rubber mounting feet on the base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to move or shake whilst the XR1200 is moving.
Eight quarter turn fast locks placed on the base of the units,allows by using the two fast lock C clamps
.
provided in the box, to fix the unit in any position.
9.1- Safety cable
We recommend the use of a safety cable or chain connected to the XR1200 and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the picture below.
A
!
9.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper unit functioning would be compromised should this occur.
10
XR1200 WASH
9.3- Movement
The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any obstructions in the path of the projector's movement.
!
WARNING
Do not place any object in the path of the projector’s movement
270°
540°
9.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended distance from flammable material is 1 MT.
F
Minimum distance from the object being illuminated is 2 MT.
2M
9.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on both the base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
9.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature should NOT exceed 40°C.
10- MAINS CONNECTION
XR1200 with electronic ballast operate at 90-260 VOLT 50-60 Hz.
Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. For connection purposes, ensure that your plug is capable of supporting 8 amps at 230V,
Or 16 amps at 100-120 V
Strict adherence to regulatory norms is strongly recommended.
10.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each XR1200.
A good earth connection is essential for the correct operation of the projector.
Electronic ballast
90-260V 50 / 60Hz
!
11
XR1200 WASH
11- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a
CANNON XLR 5 or 3 pins connector.
Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one.
In this way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
5
4
CONTROLLER
S T A N D A R D
D M X 5 1 2
1
2
1=GND
2=DATA-
3=DATA+
3
For Installations where long distance DMX cable connections are needed,we suggest to use a DMX terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
5
4
3
2
1
OUT
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
120 ohm
PIN 3
PIN 2
12
11.1-DMX Addresses
XR1200 WASH have 16 DMX channels.
Set the following addresses on the mixer:
Projector 1 A001
Projector 2 A017
Projector 3 A033
…..
A….
projector 6 A081
If you want to select the next projector, just add “16”
XR1200 WASH
11.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now setted to the new DMX address.
TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.
12 FIRMWARE UPDATING
!
Warning:
This procedure require a base knolewge of computer applications and Windows
Hyperterminal program.
Please refer to an authorised D.T.S. service centre.
To update the software version of the Xr1200 WASH you will need:
D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).
USB-DMX Driver for the D.T.S. RED BOX interface .
(The driver and the installation procedure are available in our web site www.dts-lighting.it)
Updating the software version.
Please follow the procedure below to perform the update:
1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.
2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.
3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.
4. Download the new software version into the unit by using Windows Hyperterminal program.
It will be possible to download the software from the reserved area of D.T.S. web site:
www.dts-lighting.it.
13
XR1200 WASH
13- DISPLAY FUNCTIONS
DMX OUT
DISPLAY
DMX IN
DMX IN FUSE 16A T 5X20
DMX OUT
MENU
ENTER
UP
DOWN
MAINS
Electronic ballast
90-260V 50 / 60Hz
DISPLAY FUNCTIONS
The XR1200 display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the DTS setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.
SOFTWARE VERSION: 8 motors R.20 / Pan&Tilt R.29
Menu
Up-Down
Pan Direction
PAN DIRECTION
This menu allow to set the Pan movement.
Normal or Reversed
ENTER Up-Down
PAN DIRECTION
NORMAL
Pan movement Normal or Reversed
Default = Normal
ENTER
MENU ENTER DOWN UP
Menu
Up-Down
Tilt Direction
TILT DIRECTION
This menu allow to set the Pan movement.
Normal or Reversed
ENTER Up-Down
TILT DIRECTION
Tilt movement Normal or Reversed
Default = Normal
NORMAL
ENTER
MENU ENTER DOWN UP
Menu
Up-Down
Pan Tilt Speed
PAN TILT SPEED
Pan Tilt Speed control (1-8)
ENTER Up-Down
PAN TILT SPEED
4
Pan Tilt Speed control (1-8)
Default = 4
ENTER
MENU ENTER DOWN UP
14
XR1200 WASH
13- DISPLAY FUNCTIONS
Menu Up-Down
Display
ENTER
DISPLAY FLIP / STAND BY / CONTRAST
Up-Down
Display Flip:
Reverses display's reading depending on the mounting position
(On the ground or suspended).
Display Standby:
To turn off the display (after 5 seconds)
Or leave it always on.
Display Contrast:
Display contrast regulation (1-16)
DISPLAY
Display Flip
ON THE GROUND (Default)
SUSPENDED
ON THE GROUND
MENU ENTER DOWN UP
DISPLAY
Display Standby
OFF = Display Standby disabled
(Default)
ON = Display goes OFF after 5 seconds
OFF
MENU ENTER DOWN UP
DISPLAY
Display Contrast
1-16 (Default = 8)
ENTER
ENTER
ENTER
8
MENU ENTER DOWN UP
Menu
Up-Down
DMX Mode
DMX MODE
To select DMX mode :
Mode 1 or Mode 2
ENTER Up-Down
DMX MODE
MODE 1
Mode1 = 16 DMX channels, Pan&Tilt
16 bit (Default)
Mode2 = Same fixture as XR7 WASH
16 DMX channels, Pan&Tilt 16 bit
(Please check at page 23 for details)
ENTER
MENU ENTER DOWN UP
Menu
Up-Down
Motors Test
TEST MODE
Full test and single function test.
ENTER Up-Down
MOTORS TEST
ALL
Motors Test
ALL ,PAN, TILT, DIMMER, SHUTTER,
COLOUR WHEEL, CYAN, MAGENTA,
YELLOW,
EFFECTS, ZOOM
ENTER
MENU ENTER DOWN UP
Menu
Up-Down
Lamp
LAMP
Lamp always ON, always OFF, lamp ON-OFF selectable via DMX
And lamp life time reset
ADJUST
To adjust the lamp with no mixer connected.
It’s possible to set the parameters for
PAN-TILT and ZOOM
ENTER Up-Down
LAMP
MENU ENTER DOWN UP
LAMP
BY DMX = ON / OFF via DMX (default)
ALWAYS ON = Forced ON
ALWAYS OFF = Forced OFF
RESET COUNTER = Lamp life time reset
ENTER
LAMP ADJUST = To adjust the lamp with no mixer connected.
It’s possible to set the parameters for
PAN-TILT and ZOOM
ENTER
MENU ENTER DOWN UP
15
XR1200 WASH
13- DISPLAY FUNCTIONS
Menu
Up-Down
Reset
RESET
Reset via DMX ENABLED / DISABLED and unit reset
ENTER Up-Down
Menu Up-Down
Fan Speed
FAN SPEED
Fan Speed control
RESET
BY DMX
ENABLED
ENTER Up-Down
MENU ENTER DOWN UP
FAN SPEED
12
ENABLED = Reset via DMX enabled
(Default)
DISABLED = Reset via DMX disabled
NOW = Unit motors reset
ENTER
Fan speed control
1-12 (Default = 12)
ENTER
MENU ENTER DOWN UP
Menu Up-Down
CMY Blackout
ENTER Up-Down
CMY BLACKOUT
CMY filters blades inserted at 100% if the dimmer remain closed for more than 5 seconds.
By activating this function, it will be possible to reduce substantially any visible light reflection coming out from the front lens when dimmer is closed.
CMY BLACKOUT
ON
MENU ENTER DOWN UP
ON = Blackout enabled (Default)
OFF = Blackout disabled
ENTER
Menu Up-Down
System info
ENTER
SYSTEM INFO
Lamp life time, lamp strikes, unit life time, 8 motors card software version, Pan&Tilt card software version and unit model
Up-Down
SYSTEM INFO
LAMP LIFE:0006H STRIKE:003
UNIT LIFE: 0010H
8M R.20
PT R.29
MODEL: XR1200 WASH SILENT
MENU ENTER DOWN UP
SYSTEM INFO
Lamp life time, lamp strikes, unit life time, 8 motors card software version, Pan&Tilt card software version and unit model
ENTER
Menu Up-Down
Reserved
RESERVED
Pan lock-Tilt lock
Pan free-Tilt free
System Reboot
(Code = 100)
ENTER Up-Down
RESERVED
ENTER CODE
000
MENU ENTER DOWN UP
PAN LOCK
NO
Pan Lock = Lock the Pan to the desired value
Tilt Lock = Lock the Tilt to the desired value
Pan Free = Remove power to Pan motor
Tilt Free = Remove power to Tilt motor
System Reboot = Unit Reboot without needing of turning OFF the unit
ENTER
TILT LOCK
NO
MENU ENTER DOWN UP
PAN FREE
NO
TILT FREE
NO
REBOOT
MENU ENTER DOWN UP MENU ENTER DOWN UP MENU ENTER DOWN UP MENU ENTER DOWN UP
16
XR1200 WASH
13- DISPLAY FUNCTIONS
Menu Up-Down
Default
DEFAULT
To restore main settings
ENTER Up-Down
DEFAULT
RESTORE MAIN SETTINGS
Default
To restore main settings
MENU ENTER DOWN UP
DEFAULT
RESTORE MAIN SETTINGS
SURE?
PRESS ENTER TO CONFORM
PRESS MENU TO CANCEL
MENU ENTER DOWN UP
Menu
Up-Down
Frost
ENTER Up-Down
Frost
To be set “ YES” in case FROST filter 0506V016 provided as standard accessory in the box will be applied on the EFFECT wheel of the unit.
This MENU affect ZOOM excursion
FROST
NOT
MENU ENTER DOWN UP
Frost
Not = Not inserted (Default)
Yes = Inserted
ENTER
ENTER
14- ERROR MESSAGES
ERROR
COLOUR WHEEL
MENU ENTER DOWN UP
COLOUR WHEEL
POSITION ERROR
ERROR
EFFECTS
MENU ENTER DOWN UP
BEAM SHAPE WHEEL
POSITION ERROR
ERROR
ZOOM LEFT
MENU ENTER DOWN UP
LEFT ZOOM SENSOR
POSITION ERROR
ERROR
ZOOM RIGHT
MENU ENTER DOWN UP
RIGHT ZOOM SENSOR
POSITION ERROR
ERROR
PAN
MENU ENTER DOWN UP
PAN REPOSITIONING
ENCODER ERROR
ERROR
TILT
MENU ENTER DOWN UP
TILT REPOSITIONING
ENCODER ERROR
ERROR
INTERNAL BUS
MENU ENTER DOWN UP
COMMUNICATION
PROBLEM BETWEEN 8
MOTORS CARD AND
PAN&TILT CARD
ERROR
DMX ADDRESS
MENU ENTER DOWN UP
DMX ADDRESS
ERROR
17
XR1200 WASH
15- HIDDEN MENU
For technical personnel only.
To operate this menu:
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)
Reset the XR1200 (reset from the MENU, not from the DMX controller!).
While reset is running, press the MENU and ENTER keys at the same time.
CALIBRATION
MOTORS ALIGNMENT
PAN
134
MENU ENTER DOWN UP
ELECTRONIC
CALIBRATION OF THE
MOTORS
DEFAULT CAL
SET ALL MOTORS AT 128
MENU ENTER DOWN UP
RESET EEPROM.
RESET ALL SETTINGS
TO 128 VALUE
EXIT TO MAIN
MENU ENTER DOWN UP
EXIT FROM HIDDEN
MENU
Calibration mode
CALIBRATION
MOTORS ALIGNMENT
PAN
134
MENU ENTER DOWN UP
PAN ALIGNMENT
To align pan position
CALIBRATION
MOTORS ALIGNMENT
EFFECTS
149
MENU ENTER DOWN UP
EFFECTS ALIGNMENT
To Align Effects wheel
CALIBRATION
MOTORS ALIGNMENT
MAGENTA
121
MENU ENTER DOWN UP
MAGENTA ALIGNMENT
To align magenta colour
CALIBRATION
MOTORS ALIGNMENT
TILT
167
MENU ENTER DOWN UP
TILT ALIGNMENT
To align tilt position
CALIBRATION
MOTORS ALIGNMENT
SHUTTER
145
MENU ENTER DOWN UP
SHUTTER ALIGNMENT
To align shutter blades
CALIBRATION
MOTORS ALIGNMENT
COLOUR WHEEL
151
MENU ENTER DOWN UP
COLOUR WHEEL ALIGNMENT
To align colour wheel
CALIBRATION
MOTORS ALIGNMENT
ZOOM RIGHT
97
MENU ENTER DOWN UP
ZOOM RIGHT ALIGNMENT
To align zoom right position
CALIBRATION
MOTORS ALIGNMENT
ZOOM LEFT
85
MENU ENTER DOWN UP
ZOOM LEFT ALIGNMENT
To align zoom left position
CALIBRATION
MOTORS ALIGNMENT
YELLOW
106
MENU ENTER DOWN UP
YELLOW ALIGNMENT
To align yellow colour
CALIBRATION
MOTORS ALIGNMENT
CYAN
162
MENU ENTER DOWN UP
CYAN ALIGNMENT
To align cyan colour
18
XR1200 WASH
16- OPENING THE PROJECTOR HOUSING
It is possible to inspect the inside of the projector by removing the cover as indicated below.
ATTENTION
REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.
1) Loosen the 3 (1/4 turn) screws which fix the head covers (photo 1) .
2) Once unscrewed, simply lift the covers to access the internal components (photo 2).
Photo 1
Photo 2
17- PERIODIC CLEANING
17.1- Lenses and reflectors
Even a fine layer of dust can substantially reduce the luminous output . Regularly clean all lenses and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.
17.2- Fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning will depend of course, on the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor. If necessary, clean the fans and air passages more frequently.
18- PERIODIC CONTROLS
Attention
Disconnect mains power prior to removing the projector housing.
!
Lamp
The lamp should be replaced if there is any visible damage or deformation due to heat. This will help to avoid the danger of the lamp exploding. Lamp lifespan is about 750 hours, then it is necessary to replace it.
Mechanical parts
Periodically check all mechanical parts, gears, guides, belts, etc. for wear and tear, replacing them if necessary. Periodically check the lubrication of all components, particularly the parts subject to high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S. distributor. Check the tension of the belts and adjust it if necessary.
UV
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors; refasten them if necessary.
Fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the XR1200.
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.
19
XR1200 WASH
19- DMX PROTOCOL
16 CHANNEL MODE ( 16bit)
1
2
3
PAN ms b ( 5 4 0°)
PAN lsb
TILT msb(320°)
4
5
MOVEMENT SPEED
6 D MER
7
8 C OUR
9 C
10 MAGENTA
11 YEL L O
12 SPEED CMY / DIMMER
13 MACRO CMY / COLOUR
14 E
15 ZOOM
16 RESET
DMX CHANNEL
1
Parameter:
PAN msb 540°
DMX CHANNEL
2
Parameter:
PAN lsb
DMX CHANNEL
3
Parameter:
TILT msb 319°
DMX CHANNEL
4
Parameter:
TILT lsb
DMX CHANNEL
5
Parameter:
MOVEMENT SPEED
DMX range
Value
0-10
11-25
26-127
128-247
Mid point
DMX value
Move range
(degrees)
Mode Option
248-255
DMX CHANNEL
6
Parameter:
DIMMER
Function
Standard
Fast movement
Vector mode from fast to slow
Variable time reaction to
DMX signal ( fast to slow)
Slow reaction time to DMX signal
DMX range
Value
0-8
9-255
Mid point
DMX value
Move range
(degrees)
Mode Option Function
Black-out
Proportional dimmer
0-12
13-25
26-38
39-51
52-64
65-77
78-90
91-103
104-116
117-129
130-142
143-155
156-168
169-181
182-197
198-200
201-203
204-206
207-209
DMX CHANNEL
DMX range
Value
0-9
10-23
24-37
38-51
52-65
66-79
80-93
94-107
108-121
122-135
136-149
150-163
164-177
178-191
192-205
206-219
220-227
228-233
234-255
DMX CHANNEL
7
Parameter:
SHUTTER
Mid point
DMX value
Move range
(degrees)
Mode
8
Parameter:
COLOUR
DMX range
Value
Mid point
DMX value
Move range
(degrees)
Mode
20
ARC 1200
Option Function
Black-out
Strobe random speed
Strobe speed 1 min.
Strobe speed 2
Strobe speed 3
Strobe speed 4
Strobe speed 5
Strobe speed 6 max.
Flash open speed 1 min.
Flash open speed 2
Flash open speed 3
Flash open speed 4 max.
Flash closed speed 1 min.
Flash closed speed 2
Flash closed speed 3
Flash closed speed 4 max.
Colours / Macros in black-out
Pan / Tilt in black-out
Open
Option Function
White
Colour 1 (3200° K)
Colour 2 (5600°K)
Colour 3
BiColour 3/4
Colour 4
BiColour 4/5
Colour 5
BiColour 5/6
Colour 6
BiColour 6/7
Colour 7
Bicolour 7/8
Colour 8
Bicolour 8/white
Right rotation speed 1 max.
Right rotation speed 2
Right rotation speed 3
Right rotation speed 4
-
21
210-212
213-215
216-218
219-221
222-224
225-228
229-231
232-234
235-237
238-240
241-243
244-246
247-249
250-252
253-255
DMX CHANNEL
9
Parameter:
CYAN
DMX range
Value
0-255
Mid point
DMX value
Move range
(degrees)
DMX CHANNEL
Mode
10
Parameter:
MAGENTA
DMX range
Value
0-255
Mid point
DMX value
Move range
(degrees)
DMX CHANNEL
Mode
11
Parameter:
YELLOW
Option
Option
Right rotation speed 5
Right rotation speed 6
Right rotation speed 7
Right rotation speed 8
Right rotation speed 9 min
Stop
Left rotation speed 1 min.
Left rotation speed 2
Left rotation speed 3
Left rotation speed 4
Left rotation speed 5
Left rotation speed 6
Left rotation speed 7
Left rotation speed 8
Left rotation speed 9 max.
Function
Proportional colour
Function
Proportional colour
DMX range
Value
0-255
DMX CHANNEL
Mid point
DMX value
Move range
(degrees)
12
Parameter:
Mode Option
SPEED CMY / DIMMER
DMX range
Value
0-7
8-255
Mid point
DMX value
Move range
(degrees)
Mode Option
Function
Proportional colour
Function
No Function
Variable speed from max to min
-
22
85-89
90-94
95-99
100-104
105-109
110-114
115-121
122-128
129-135
136-142
143-149
150-156
157-163
164-170
171-177
178-184
DMX range
Value
0-9
10-14
15-19
20-24
25-29
30-34
35-39
40-44
45-49
50-54
55-59
60-64
65-69
70-74
75-79
80-84
185-191
192-198
199-205
206-212
213-219
220-226
227-233
234-240
241-247
247-255
DMX CHANNEL
13
Parameter:
MACRO CMY / COLOUR
Mid point
DMX value
Move range
(degrees)
Mode Option Function
No Function
Macro 1
Macro 2
Macro 3
Macro
21
Macros rainbow wait = 3
Macros rainbow wait = 4
Macros rainbow wait = 7
Macros rainbow wait = 8
Macros rainbow wait = 9
Macros rainbow wait = 10
Full colours rainbow wait = 0
Full colours rainbow wait = 2
Full colours rainbow wait = 3
Full colours rainbow wait = 4
Full colours rainbow wait = 5
Full colours rainbow wait = 6
Full colours rainbow wait = 7
Full colours rainbow wait = 8
Full colours rainbow wait = 9
Full colours rainbow wait = 10
-
DMX CHANNEL
14
Parameter:
EFFECTS
DMX range
Value
0-19
20-39
40-255
Mid point
DMX value
Move range
(degrees)
Mode
DMX CHANNEL
15
Parameter:
ZOOM
DMX range
Value
0-225
DMX CHANNEL
Mid point
DMX value
Move range
(degrees)
16
Parameter:
Mode
LAMP / RESET
MODE 1 (DEFAULT)
DMX range
Value
0-9
10-60
61-129
130-179
180-200
201-239
240-255
Mid point
DMX value
5
30
95
154
190
220
247
Move range
(degrees)
Mode
23
Option
Option
Function
Standard Frost inserted
No Frost inserted
Beam Shape
Function
Proportional
Option Function
No Effect
Lamp OFF (Active after 3 seconds)
No Effect
Lamp ON (Active after 3 seconds)
No Effect
Internal Motors Reset
Total Reset
-
MODE 2 SAME AS XR 7 WASH (Please check at page 14
“DMX MODE” for details)
Move
DMX range Mid point range
Value DMX value
(degrees)
0-29
30-85
236-255
Mode Option Function
No effect
Lamp OFF (active after 3 seconds)
Internal motor Reset
Total Reset
Lamp ON (active after 3 seconds)
86 - 170
171-235
20- COLOUR WHEEL
2
1
COL1
3
24
4
5
8
COL2
7
COL3
6
COL4
-
0507K004
CONV.FILTER CTO
TC3256
COL5
0507K003
CONV. FILTER CTB
DL542
COL6
0507C046.D01
WOOD SW 460
COL7
0507C051.D01
ORANGE LW590
COL8
0507C042.D01
GREEN WB5055
0507C047.D01
RED LW 640
0507C041.D01
DARK BLUE SW490
0507C053.D01
AMBER LW 550
25
21- 8 MOTORS CONTROL CARD
8 MOTORS CONTROL CARD
J7 Magnetic Sensors
Connector
Line 1 Brown:
Line 2 Orange:
GND
ORANGE
BROWN
VCC
J1 Internal DATA
Communication
Connector
From J8 Pan & Tilt card
30 VDC
+
-
Fans
XR1200 WASH
Zoom motor1
(BLACK)
Zoom motor2
(DARK GREEN)
Strobe
(YELLOW)
Colour wheel
(PINK)
Effects
(GREY)
Magenta
(LIGHT BLUE)
Cyan
(GOLD)
Yellow
(BLUE)
Fans
22-PAN & TILT CARD
26
PAN
(WHITE)
TILT
(BROWN)
GND
(BLACK)
30 VDC
(RED)
FAN
(WHITE)
ENCODER PAN
(RED)
ENCODER TILT
(ORANGE)
TO J1
DISPLAY CARD
(WHITE)
TO J1
8 MOTORS CARD
(GREEN)
23-CABLES RESEND CARD
24-DISPLAY CARD
DMX INPUT
(WHITE)
FROM J12
PAN&TILT
CARD
TO J2
LAMP
ON-OFF
CARD
25-LAMP ON-OFF CONTROL CARD
J4
FROM J16
PAN&TILT
CARD
J2
J3
TO J9
ELECTRONIC
BALLAST
NOTES
27
The information contained in this publication has been carefully prepared and checked.
However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.
MADE IN ITALY
*0517I100*
0517I100
D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy
Tel. +39 0541 611131 Fax +39 0541 611111 [email protected] www.dts-lighting.it
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project