CCTV LCD Monitor User Manual

Add to my manuals
26 Pages

advertisement

CCTV LCD Monitor User Manual | Manualzz
CCTV LCD Monitor
User Manual
For modes:
EL-22MC1RF
EL-22MC1RE
ENGLISH
Contents
1. Introduction………...........................................................................................................................................1
2. Work Safety Information................................................................................................................................ 2
2.1. Product Safety Precautions information.......................................................................................................2
2.2. Safety Guidelines.........................................................................................................................................3
2.3. Important Notice Concerning Power Cord Selection....................................................................................3
2.3.1 For the United States and Canada...................................................................................................... 4
2.3.2 For European Countries.......................................................................................................................4
2.3.3 For the United Kingdom.......................................................................................................................4
3. Standards and Guidelines..............................................................................................................................6
3.1. FCC Requirements.......................................................................................................................................6
3.2. FCC Warning ............................................................................................................................................. 6
3.3 CE Conformity……………............................................................................................................................ 7
3.4 RoHS Compliance Statement..................................................................................................................... 7
3.5 Information on Disposal for Your Old Product..............................................................................................7
4. Hardware Installation.....................................................................................................................................8
4.1 Checking the Accessories Supplied..............................................................................................................8
5. Buttons and Connections...............................................................................................................................8
5.1 Buttons……..................................................................................................................................................8
5.2 Connections..................................................................................................................................................9
6. ID Remote Controller …………………………………………………………………………………………..…….10
7. OSD Setup ………………………………………………………………………………………………………..……12
8. Troubleshooting Guide…………………………………………………………………………………………….…22
9. Applicable Video Timing for PC- analog Video…………………………………………………………….….…23
10.Technical Data ………………………………………………………………………………………………………..24
1
Introduction
Thank you for purchasing the professional CCTV LCD Monitor and welcome to a fantastic new
technology that will completely change the way you look at monitors. The following sections
describe just a few of the major advantages of this LCD monitor. You’ll discover more of its wonderful
features as you use it.
Please note that this manual is used with many similar monitor models. Please check the model
number on the carton and on the back of the unit to make sure if the user manual is applicable to
your machine.
1. The LCD monitor is used in the same way as the CRT monitor. There is no need to change the
hardware of your computer, just plug it in and it is ready for use.
2. The monitor will accept and display analog video (NTSC or PAL) , PC-type video and Digital
video(HD-SDI, DVI, HDMI) sources .
3. Low radiation and reduced flickering compared to traditional CRT monitors that minimizes
eyestrain and health hazards.
4. The compact size makes transportation easier and allows to use in many applications.
5. This LCD monitor can support PC-VGA, Composite , S-Video signals and Digital, DVI,HDMI
HD-SDI signals.
6. The composite video input ports accept different signal sources, e.g. Camera, DVR .. etc.
7. The design allows VESA wall mounting installation.
8 This monitor includes special functions for 3D comb filter, De-interlace, Anti burn-in mode, auto
impedance switch for looping video connection .
9. The remote controller has 999 ID code to control individual monitor on the TV wall.
1
2
Work Safety Information
Caution and Warning
CAUTION !!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock, do not
remove cover (or back).
No internal parts can be serviced by users.
Refer servicing to qualified personnel.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS CCTV
LCD MONITOR TO RAIN OR MOISTURE.
WARNING
2.1
“HIGH VOLTAGE EXISTS ON THE BACK LIGHT POWER LEAD OF THIS
CCTV LCD MONITOR. BEFORE SERVICING, DETERMINE THE
PRESENCE OF HIGH VOLTAGE BY CONNECTING THE H.V. METER
BETWEEN THE BACK LIGHT POWER LEAD AND CHASSIS ONLY“
Product Safety Precautions
Follow all warnings and instructions marked on the product.
1.
Do not use this product near water.
2.
This LCD monitor should be installed on a stable horizontal base.
3.
When cleaning, use only a neutral detergent cleaner with a soft damp cloth. Do not spray with liquid
or aerosol cleaners.
4.
Do not expose this LCD monitor to direct sunlight or heat. Hot air may cause damage to the cabinet
and other parts.
5.
Adequate ventilation must be maintained to ensure reliable and continued operation and to protect
the LCD monitor from overheating. Do not block ventilation slots and openings with objects or install
the LCD monitor in a place where ventilation may be obstructed.
6.
Do not install this LCD monitor near a motor or transformer where strong magnetism is generated.
Images on the LCD monitor will be distorted and the color irregular.
7.
Do not allow metal pieces or objects of any kind fall into the LCD monitor through ventilation holes.
8.
Do not attempt to service this unit yourself. Removal of the LCD monitor cover may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
2
9.
Unplug this product from the wall outlet and refer servicing to qualified service personnel in the event
that:
- Liquid is spilled onto the product or the product is exposed to rain or water.
- The product does not operate normally when the operating instructions are followed.
- The product has been dropped or the cabinet has been damaged.
- The product exhibits a distinct change in performance, indicating a need for service.
- The power cord or plug is frayed or damaged.
- Has referred to Troubleshooting Tips and problems still can’t be solved.
2.2
Safety Guidelines
CAUTION
The socket outlet should be installed near the equipment and should be
easily accessible.
Français
This device must be operated with the original power supply.
English
WARNING
CAUTION
Switzerland…….SEV
Canada……CSA
Britain…………..BASE/BS
Germany…..DE
Japan…………...Electric Appliance Control Act.
Español
2.3
USA………..UL
Deutsch
Use a power cord that is properly grounded. Always use the appropriate AC
power cord that is certified for the individual country. Some examples are
listed below:
Important Notice Concerning Power Cord Selection
The power cord set for this unit has been enclosed and has been selected according to the country of
destination. It must be used to prevent electric shock. Use the following guidelines if it is necessary to
The female receptacle of the cord set must meet IEC-60320 requirements and may look like this (Figure A1
below):
Polski
Figure A1
Italiano
replace the original cord set, or if the cord set is not enclosed.
Figure A2
3
Česky
Svensk
2.3.1
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2, above), UL Listed, and
CSA Labeled. For units which are mounted on a desk or table, SVT or SJT type cord sets may be used.
For units which sit on the floor, only SJT type cord sets may be used. The cord set must be selected
according to the current rating for your unit. Please consult the table below for the selection criteria for
power cords used in the United States and Canada.
2.3.2
Code Type
Size of Conductors in Cord
Maximum Current Rating of Unit
SJT
18 AWG
16 AWG
14 AWG
10 Amps
12 Amps
12 Amps
SVT
18 AWG
17 AWG
10 Amps
12 Amps
For European Countries
In Europe you must use a cord set which is appropriate for the receptacles in your country. The cord set is
HAR-Certified, and a special mark that will appear on the outer sheath, or on the insulation of one of the
inner conductors.
2.3.3
For the United Kingdom
For your safety please read the following text carefully.
If the fitted molded plug is unsuitable for the socket outlet, then the plug should be cut off and disposed of
safely.
DANGER
Do not plug the cut-off plug into a socket outlet! There is a danger of severe
electrical shock!
If a new plug is to be fitted, please observe the wiring code as shown below. In case of doubt, please
consult a qualified electrician.
WARNING
This appliance must be earthed (grounded).
IMPORTANT
The wires in this mains lead are colored in accordance with the following codes:
Green-and-Yellow : Ground (Earth)
Blue : Neutral
Brown : Live
4
f the colored wires of the mains lead of this appliance do not correspond with the colored markings
identifying the terminals in your plug, proceed as follows:
The wire which is colored GREEN-AND-YELLOW must be connected to the terminal in the plug which is
marked by the letter E or by the Earth symbol or colored GREEN or GREEN-AND-YELLOW.
The wire which is colored BLUE must be connected to the terminal in the plug which is marked with the
letter N or colored BLACK.
The wire which is colored BROWN must be connected to the terminal in the plug which is marked with the
letter L or colored RED.
If you have any questions concerning the proper power cord to use, please consult the dealer from whom
you purchased the product.
5
Standards and Guidelines
3.1
English
3
FCC Requirements
Français
This device complies with Part 15 of the FCC Rules and Regulations. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must tolerate any
interference encountered, including interference that may cause improper operation.
The equipment has been tested and found to comply with the requirements stipulated in Part 15 of FCC
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in strict compliance with the instructions, may disrupt
Deutsch
regulations for a Class B digital device. These requirements are designed to provide reasonable protection
radio communications. However, there is no guarantee that interference will not occur in a particular
Español
installation. If this equipment does cause detrimental interference with radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by taking one or more of the following measures:
Reorienting or relocating the receiving antenna.
Increasing the separation between the equipment and the receiver.
Italiano
Connecting the equipment into an outlet on a circuit different from the one which the receiver is
connected.
Consulting the dealer or an experienced radio/TV technician for help.
compliance with the pertinent RFD emission limits governing this device.
Changes or modifications not expressly approved by the manufacturer could void the user’s right to operate
Polski
Shielded interconnected cables and shielded power cords must be used with this equipment to ensure
the equipment.
Česky
Notice of Compliance with Canadian Interference-causing Equipment Regulations
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Svenska
3.2
FCC Warning
Nederlands
To ensure continued FCC compliance, the user must use a grounded power supply cord and the shielded
video interface cord with bonded ferrite cores provided. If a BNC cable is going to be used, use only a
shielded BNC (5) cable. Also, any unauthorized changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this device.
6
3.3
CE Conformity
The device complies with the requirements of the directive
2004/108/EC with regard to “Electromagnetic compatibility”, and
206/95/EC with regard to “Safety”.
3.4
RoHS Compliance Statement
in European Union Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in
English
This display defined in this user manual is 100% RoHS complaint and meets all the requirements set forth
Electrical and Electronic Equipment.
Information on Disposal for Your Old Product
Used electrical and electronic equipment must be treated separately and in accordance
with legislation that requires proper treatment, recovery and recycling of used electrical and
electronic equipment. When this crossed-out wheeled bin symbol is attached to a product,
it means the product is covered by the European Directive 2002/979/EC. If you wish to
discard of this product, please contact your local authorities and ask the correct method of
disposal. The correct disposal of your old product will help prevent potential negative
consequences for the environment and human health.
Attention: if you want to dispose of this equipment, please do not use this ordinary dust bin!
Italiano
Česky
7
Français English
Deutsch Français
Español Deutsch
Italiano Español
Polski
3.5
Polski
Svenska
4.
Hardware
This chapter will guide you through the correct installation procedures for the LCD monitor.
4.1. Checking the Accessories Supplied
LCD monitor body + Desk Stand
x 1 pc
AC power cord
x 1 pc
Adaptor
x 1pc
D-Sub 15-pin cable (1.8 Meter)
x 1 pc
Ø 3.5mm audio line (1.5 Meter)
x 1 pc
User manual (CD)
x 1 pc
Remote Controller
x 1 pc
Battery (AAA)
x 2 pcs
5. Buttons and Connections
5.1 Buttons
1
○
2
○
3
○
4
○
5
○
1 “Menu/Enter” :
To enter the OSD menu or confirm the setting.
2”▲/+” Up/Increase :
To move the cursor upwards or to switch over the setting items or to increase the figure of the setting
Selected
8
3"
“ Power :
Press button to turn the power on and press again to turn the power off.
4.”▼/-” Down/Decrease:
To move the cursor downwards or to switch over the setting items or to decrease the figure of the
setting selected.
5 “Source/Exit”
1. To select the input signal source when the OSD menu is Off. The available signal source will show in
the following order: Video-1, S-Video, VGA , HDMI .
2. To exit the menu when you finish the setting.
5.2 Connections
1
2
3
4
5
6
7
8
9
10
Alarm Trigger
Item
Connector
Function
1
DC 12 Input
Please use DC 12V, 5A Power Adaptor
2
HDMI Input
(DVI is supported)
Connect to the digital video signals output of computer or DVR (DVI
is also supported through HDMI, using a DVI to HDMI adaptor cable)
3
VGA (D-Sub) Input
Connect to the VGA output of your computer or DVR
4
S-Video Input
Connect the S-Video(4-pin DIN) connector from the DVR or AV
equipment to the Monitor .
5
Composite Video Input
and Output (BNC type)
This Video input and output are used for CVBS input and output.
This monitor also supports the“ auto looping“ function, permitting the
connection of another monitor from the output connector.
Stereo RCA Audio Input
(R/L)
Stereo audio input , “R“ is right channel (Red) of audio connector,
“L“ is the left channel(White) of the audio of connector.
9
PC Audio Input (Ø 3.5mm)
Connect to the audio output of your computer
Alarm Trigger (Ø 3.5mm)
Please connect the Ø 3.5mm Alarm cable to DVR alarm output and
provide +3~5V DC Voltage to trigger the PIP, the sub screen will
show the “Alarm Message” you setup on the DVR.
6
7
8
9
6. ID Remote Controller
. POWER switch.
Press to turn ON or turn OFF the LCD Monitor.
. VIDEO SIGNAL Selection:
Press the “AV1” “AV2”, “S-VIDEO”, “D-SUB”,”DVI”, “HDMI” ,
“HD-SDI” button to enter the selected video source or press
the “SOURCE” button to have the cycle video selection.
. PIP Hot Key:
Press PIP button to enter “PIP” setup.
. PBP Hot Key:
Press PBP button to enter the PBP setup
. SWAP Hot Key:
Press SWAP button to exchange the main and sub screen.
. VOL:
Press “+” to increase volume and press “-“ to decrease volume.
. DEFAULT :
Press “Default” to clear all the setting and return to factory
default.
. MUTE and PAUSE :
Press “MUTE” to mute the sound and press “PAUSE” to pause
the video.
. OSD setup:
a. Press the “MENU” to enter the OSD menu and press
“ENTER” to access into item option, press “
▲ UP”
or “
▼
DOWN” to select setting item and press “ENTER” again until
Yellow bar changes to Pink bar. Press “ +” to increase or
“ -
” to decrease the “pink bar” to adjust the setting.
b. Press the “EXIT” to exit the menu and confirm the setting.
c. Press the “ENTER” to confirm the ID number setting.
10
. ID and Number Key:
Step 1: Setup the Monitor ID No.
Press “MENU“ to enter the OSD menu and press “
/+
“ button to select the “Function“ menu and press ”ENTER” to
access into item option. Press “
▼ DOWN” to choose “ID
Controller “ setup and press “ +” or “ -
” again to
switch to “ON”
To access into “ID” item and press “ENTER” to setup the “ID”
No. Press 3 digit (001~999) as the monitor ID No. and press
“EXIT” to confirm the input. When you press the “ID” button,
the screen will show “ Monitor ID : 001 (when you input ” 001 )
.
Step 2: Control the monitor with ID No.
Press “ID“ button, the screen will show the“ Monitor ID “: 001
input 3 same digit on “ ID “ and press “ENTER“ to confirm the
input. Then you can control the monitor.
For example:
When you setup the Monitor “ID” No“ is “001“, press the
“ID“ button and input 001 and press “ENTER“ to confirm the
input. You can control the monitor with Monitor ID No.001 only.
You are not able to control other monitors unless you setup all
monitors ID No. is “001“ or the“ ID Controller „ setup function is
on “Off“ status.
Notice !!!
Please don’t setup the 3 digit No. as “000“ , If you setup the
Monitor ID No. as “000“ , the ID function will be on “Off“ status.
11
7.
OSD Setup
Picture (Video / HDMI Mode)
1. Press the “Menu/Enter” key on the buttons to call out
the OSD“ Menu” . Press “▲/+” or “▼/-“ to select
“Picture” mode and press “Menu/Enter” key again to
access into item option . Press “▲/+” or “▼/-“ to
select item you want to adjust.
2. Various picture settings are available from the “Picture”
menu. Use“▲/+” or “▼/-“ to select item that you want
to adjust and press “Menu/Enter” key again until yellow
bar changes to pink bar and press “▲/+” or “▼/-“
increase or decrease the figure that you wish . Press
“Exit” key to return to menu and confirm the setting.
Press two times of “Exit” to exit all the menu.
Contrast
Press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to adjust contrast. Increasing contrast will make
white area of the video picture brighter. Contrast works in conjunction with “Brightness”.
Brightness
Press“▲/+” or “▼/-“ to increase/decrease the “Pink bar” to adjust brightness. Adjusting brightness to
enhance the level of dark area in the video picture such as night scenes and shadow scenes. Increasing
brightness will make dark areas more visible.
Tint
Press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to adjust hue. Using hue to adjust the color of flesh
tones. Increasing figure will make the picture with more red in appearance. Decreasing figure will shift the
picture with more green in appearance.
(Remark). No tint adjustment under HDMI mode
Saturation
Press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to adjust color saturation. Increasing color figure will
make the color more intense. Reducing color figure will make the color less intense.
Sharpness
Press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to adjust sharpness. Using sharpness to adjust the
detail enhancement to the video picture. Increasing the figure will enhance the edges of objects in the
video picture. Decreasing the figure will reduce enhancement.
12
Backlight
Press “▲/+” or “▼/-“ to select “ High / Medium / Low / Min “ to adjust backlight. “High” level will make the
backlight in most high light, the “Min” will minimize the backlight.
Color Temp.
Select the Color Temp.” for white balance. Press “Menu/Enter” to enter color temp. option. There are 4
settings to choose from (1)Standard (2). Warm (3).Cold (4) User. To select “User” you may press “▲/+” or
“▼/-“ to increase/decrease the “Pink bar” to adjust color of Red, Green and Blue.
Sound Effect (Video/HDMI Mode)
1. Press the “Menu/Enter” key on the buttons to call out the
OSD Menu” . Press “▲/+” or “▼/-“ to select “Sound
Effect” and press “Menu/Enter” key again to select the
item you want to adjust.
2. Various sound effect settings are available from the
“Sound Effect” menu. Use“▲/+” or “▼/-“ to select item
that you want to adjust and press “Menu/Enter” key again
until yellow bar changes to pink bar and press “▲/+” or “▼/-“
increase or decrease the figure that you wish . Press
“Exit” key to return to menu and confirm the setting.
Press two times of “Exit” to exit all the menu.
Volume
Just press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to adjust volume when item “Mute” is Off .
Bass
Press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to enhance the bass or reduce the bass.
Treble
Press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to increase the treble or reduce the treble.
Balance
Press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to enhance right speaker or enhance the left
speaker. Put the figure on “0” will keep the balance of right speaker and left speaker.
Mute
Press “▲/+” or “▼/-“ to switch On or switch Off the mute function.
13
Function (Video/HDMI Mode)
1. Press the “Menu/Enter” key on the buttons to call out the
OSD “Menu” . Press “▲/+” or “▼/-“ to select “Function”
Mode and press “Menu/Enter” key again to select the
“Function” option.
2. Various function settings are available from the
“Function” menu. Use“▲/+” or “▼/-“ to select item
that you want to adjust and press “Menu/Enter” key
again until yellow bar changes to pink bar and press
“▲/+” or “▼/-“ increase or decrease the figure that
you wish . Press “Exit” key to return to menu and confirm
the setting. Press two times of “Exit” to exit all the menu.
Language
The default language is English, you may press the “Menu/Enter” key and press “▲/+” or “▼/-“ key to select
language you want. There are 7 languages to select (1) English (2) French (3) Germany (4) Spanish (5)
Italian (6) Russian (7). Chinese
Image Mode (Video mode)
In order to meet different applications in video output, there are 5 image ratio to choose (1) Full Scan (2)
Under Scan-V (3). Over Scan-H (4). Over Scan-1 (5). Over Scan-2. Press “▲/+” or “▼/-“ key to select the
format ratio you want.
1. Full Scan
The image fully fills up the screen on both
“Vertical” and “ Horizontal” lines.
2. Under Scan-V
The format is the “Letter Box” under scan mode
that will create a black bar on both top and
bottom of frame.
14
3.Over Scan-H
The format is the over scan mode that provide a
true 4:3 format that will create a black bar on both
right and left of frame.
4. Over Scan-1
The format is over scan mode to make the image
fill up the 16:9 screen and cut about 3% on both
“Vertical” and “Horizontal” lines.
5. Over Scan-2
The format is another over scan mode to make
the image fill up the16:9 screen and cut about
6% on both “Vertical” and “Horizontal” lines.
Image Mode (HDMI mode)
When HDMI as the video interface, there are 5 image ratio to choose (1) Full Scan (2) Under Scan-V (3).
Over Scan-H (4). Over Scan-1 (5). Over Scan-2. Press “▲/+” or “▼/-“ key to select the format ratio you
want.
1. Full Scan
The image fully fills up the 16:9 screen on both
“Vertical” and “ Horizontal” lines.
2. Under Scan-V
The format is the “Letter Box” under scan mode
that will create a black bar on both top and
bottom of frame.
15
3. Over Scan-H
The format is the over scan mode that provide a
4:3 format that will create a black bar on both right
and left of frame.
4. Over Scan-1
The format is over scan mode to make the image
fill up the 16:9 screen and cut about 3% on both
“Vertical” and “Horizontal” lines.
5. Over Scan-2
The format is another over scan mode to make
the image fill up the16:9 screen and cut about
6% on both “Vertical” and “Horizontal” lines.
OSD Time
If you want the OSD Menu to stay longer on the screen, press “Menu/Enter” key and press “▲/+” or “▼/-
“ key to select “OSD Time”, there are 4 time table to select (1) 30 Sec. (2) 60 Sec.(3). 90 Sec. (4) 180 Sec.
Sleep Time
The function will make the monitor in sleep mode to save the power when monitor is in standby mode. To
press “Menu/Enter” to enter the option and press “▲/+” or “▼/-“ key again to select (1). 30 Min (2). 60 Min.
(3).90 Min (4) Off. To select 30 Min that means the monitor will enter sleep mode when monitor is in
standby mode for more than 30 Min. The other time options are the same rule.
Source Lock
The function will stop the signal auto scan process and fix the signal source you preferred. To select
“Source lock” and press “Menu/Enter” and select “Yes” to activate the source lock function, select “No”
will close the source lock function.
16
Key Lock
The function is to prevent from the kid’s playing or mis-press to change the setting. Press “Menu/Enter”
and select “Yes” to activate the key lock function, select “No” will close the key lock function.
If you want to release the Key Lock function you can press “Menu/Enter” and “Source/Exit” key
simultaneously.
Anti Burn-in
The function can prevent the LCD panel from burn-in when camera or DVR is always displaying the same
picture source at all times. Press “▲/+” or “▼/-“ key to select “ Anti Burn-in” and press “Menu/Enter” to enter
the option and press “▲/+” or “▼/-“ key again to select (1). 15 Min (2). 30 Min. (3).60 Min (4).90 Min (6).Off.
To select 30 Min. the image will move left for one pixel for every 30 minutes, to select 60 Min, the image will
move left for one pixel for every 60 minutes, the other options are the same regulation.
3D NR
To use 3D NR to reduce the noise level and improve the video quality. There are four levels to select (1)
High (2) Medium (3) Low (4) Off. Press “Menu/Enter” and press “▲/+” or “▼/-“ key to select the level.
ID Controller
The ID function is only applicable for some specific models, if the model you brought has the ID function,
Please check the ID setup procedure on page 10.
Default
If you want to back to factory default, press Menu/Enter and then press “▲/+” or “▼/-“ key to select “ Default”
“ . Press “Menu/Enter” key and press to “▲/+” or “▼/-“ key activate “Yes”
Multi Screen (Video/HDMI Mode)
Press the “Menu/Enter” key on the buttons to call out the
OSD “Menu” . Press “▲/+” or “▼/-“ to select “Multi
Screen” and press “Menu/Enter” key again to select the
“Multi Screen” option.
Multi-Screen
There are 4 multi screen modes to select (1) PIP (2) PBP (3) PBP 4:3 (3) Off . You may press “Menu/Enter”
and press “▲/+” or “▼/-“ to select mode you want. “PIP” is Picture In Picture and “PBP” is Picture By Picture.
The PIP or PBP doesn’t allow the condition of Video on Video .
17
Main Screen
Press the “Menu/Enter” key to enter the Main Screen and press “▲/+” or “▼/-“ to select VGA as the main
screen . When the main screen is in VGA mode, the sub screen can be Video-1/ S-Video/ HDMI. But when
select Video-1/ S-Video/ HDMI as main screen, the sub screen will be VGA only.
Sub Screen
Press the “Menu/Enter” key to enter the Sub Screen and press “▲/+” or “▼/-“ to select VGA as the subscreen . When the main screen is in VGA mode, the sub screen can be Video-1/ S-Video/ HDMI.
Sub Size
Press the “Menu/Enter” key to enter the Sub Size and press “▲/+” or “▼/-“ to select the size of sub-screen .
There are 3 size to select (1).Small (2).Medium (3).Large
Sub Position
Press the “Menu/Enter” key to enter the Sub Position and press “▲/+” or “▼/-“ to select 1~5 as the position
of sub-screen 1 : Top left 2: Top right 3: Bottom right 4: Bottom left 5: Central
Sound Source
To select the sound source is from Main Screen or Sub Screen. Press “▲/+” or “▼/-“ to select Main Screen
or Sub Screen
Swap
Press “▲/+” or “▼/-“ key to enter the Swat . Press “Menu/Enter” and Press “▲/+” or “▼/-“ to activate “Yes”
to swap the main screen and sub-screen.
Picture (VGA Mode)
1. Press the “Menu/Enter” key on the buttons to call out
the OSD“ Menu” . Press “▲/+” or “▼/-“ to select
“Picture” mode and press “Menu/Enter” key again to
access into item option . Press “▲/+” or “▼/-“ to
select item you want to adjust.
2. Various picture settings are available from the “Picture”
menu. Use“▲/+” or “▼/-“ to select item that you want
to adjust and press “Menu/Enter” key again until yellow
bar changes to pink bar and press “▲/+” or “▼/-“
increase or decrease the figure that you wish . Press
“Exit” key to return to menu and confirm the setting.
Press two times of “Exit” to exit all the menu.
18
Contrast
Press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to adjust contrast. Increasing contrast will make
white area of the video picture brighter. Contrast works in conjunction with “Brightness”.
Brightness
Press“▲/+” or “▼/-“ to increase/decrease the “Pink bar” to adjust brightness. Adjusting brightness to
enhance the level of dark area in the video picture such as night scenes and shadow scenes. Increasing
brightness will make dark areas more visible.
Backlight
Press “▲/+” or “▼/-“ to select “ High / Medium / Low / Min “ to adjust backlight. “High” level will make the
backlight in most light, the “Min” will minimize the backlight.
Color Temp.
Select the Color Temp.” for white balance. Press “Menu/Enter” to enter color temp. option. There are 4
settings to choose from (1)Standard (2). Warm (3).Cold (4) User. To select “User” you may press “▲/+” or
“▼/-“ to increase/decrease the “Pink bar” to adjust color of Red, Green and Blue.
Clock
Use Clock to fine-tune the monitor when phase value is wrong. Press “Menu/Enter” and press “▲/+” or “▼/-
“ to increase/decrease the “Pink bar” to adjust the Clock.
Phase
Use phase to fine-tune the monitor to perfectly ADC clock phase synchronize to the video signal source
under RGB mode. Press “Menu/Enter” and press “▲/+” or “▼/-“ to increase/decrease the “Pink bar” to
adjust the Phase.
H-Position
Use to change horizontal position of the picture. You may press “Menu/Enter” and press “▲/+” or “▼/-“ key
to select “H-Position” . Press “▲/+” key to increase “Pink bar” to shift the picture to right or press “▼/-“ to
decrease “Pink bar” to shift the picture to left.
V-Position
Use to change vertical position of the picture. You may press “Menu/Enter” and press “▲/+” or “▼/-“ key to
select “V-Position” . Press “▲/+” key to increase “Pink bar” to shift the picture up or press “▼/-“ to decrease
“Pink bar” to shift the picture down.
Auto Adjust
Use “Auto Adjust” to fine-tune the display to perfectly synchronize to the video signal source under RGB
mode. Press “Menu/Enter” and press “▲/+” or “▼/-“ to activate “Yes” the Auto Adjust function.
19
Sound Effect (VGA Mode)
The setup is the same as page No.13 for sound setup
of “Video/HDMI Mode”.
Function (VGA Mode)
The setup is the same as page 14 for Function
adjustment of “Video/HDMI Mode”.
Image Mode(VGA Mode)
When the signal is in VGA mode, there are 2 image ratio to choose (1) Full (2) 4:3 Press “▲/+” or “▼/-
“ key to select the format you want.
1. Full
The image fully fills up the 16:9 screen on both
“Vertical” and “ Horizontal” lines.
2. 4:3
The format is the under scan mode that provide a
true 4:3 format and there will be a black bar on
both right and left of frame
20
Image Mode(HDMI-PC)
When HDMI as the PC interface, there are 2 image ratio to choose (1) Full (2) 4:3 Press “▲/+” or “▼/-“ key
to select the format you want.
1. Full
The image fully fills up the 16:9 screen on both
“Vertical” and “ Horizontal” lines to provide a true
16:9 format.
2. 4:3
The format is the under scan mode that provide a
4:3 format and there will be a black bar on both
right and left of frame.
Multi Screen (VGA Mode)
The setup is the same as page
No. 17 for Multi Screen setup of “Video/HDMI Mode”.
21
8.
Troubleshooting Guide
When you experience issues with the CCTV LCD Monitor , before contacting your retailer where you
made your purchase, please check the following items. The most common issue is with the
connection of AV equipment or graphic card. We recommend that at the same time of trouble
shooting, also refer to the AV equipment or graphic card user manual. Please do not use a higher
refresh rate than the maximum specified by the CCTV LCD Monitor.
Issue
No image appears on the
LCD Monitor screen
Abnormal image
Abnormal image colors on
the screen
Interference appearing on the
screen
Can only hear audio, but no
image on the screen
Can only see video, but no
audio
Troubleshooting
Check if the computer or AV equipment power cord is securely connected
to the wall socket, or to the extension cord.
Check if the LCD Monitor power switch is at the “on” position and the LED
on the front of LCD Monitor is in still green.
Check if the computer or AV equipment video (signal) cables are properly
secured.
Check and make sure the computer or AV equipment video (signal) cables
are properly and securely connected to the sockets on back of the LCD
Monitor.
Check and make sure the LCD Monitor video (signal) cables are properly
and securely connected to the VGA, BNC, RCA, S-Video, HDMI sockets
on back of the computer.
Please refer to Chapter “Function” to check if there is any improper
adjustment or setting.
Please make sure both video inputs are properly connected (BNC /RCA/
/S-Video/HDMI and VGA).
Please make sure both audio inputs are properly connected, the audio
input plugs are RCA and Ø 3.5mm audio line-in.
Check if the volume is at the lowest level.
22
9.
Applicable Video Timing for PC- analog Video
The following table list are the better display quality modes for analogy signal (PC) supported by
this LCD monitor. The LCD monitor will stop working or has poor picture quality when other modes
out of below list input.
VGA Mode timing :
Note : 1360 x 768 for D-sub mode only
HDMI Mode Timing:
23
10.Technical Data
Model
System
Panel Size
Resolution
Pixel Pitch (H xV)
Contrast Ratio
Luminance
Aspect Ratio
Response Time
View Angel
Video Signal
Video Color System
Scan Frequency
EL-22MC1RF
EL-22MC1RE
21.5” LCD (CCFL Backligh,60Hzt)
21.5” LCD (LED Backlight, 60Hz)
1920 x 1080
1920 x 1080
0.2482(H) x 0.2482(V) mm
0.2482(H) x 0.2482(V) mm
1000:1
1000:1
250 cd/m2
250 cd/m2
16:9
16:9
Tr+Tf=5 ms
Tr+Tf=5 ms
U/D: 80/80 , L/R: 85/85
U/D: 80/80 , L/R: 85/85
Analog RGB Signal , 8 bit LVDS,
composite signal 1.0Vpp/75 ohm, Y:1Vp-p, C:0.3Vp-p
NTSC/PAL auto detection switch
H:31K~81KHz, V:60~75Hz
Operation Interfaces
Front Panel Controls
OSD Control
OSD Language
Source/Exit, -/▼,+/▲, Power, Menu/Enter
Yes
English, Francais, Deutsch, Espanol, Italiano,Russian,Chinese(7)
Input / Output Connector
HDMI
D-Sub (VGA)
S-Video
Video Input(BNC Jack)
RCA Audio (R+L)
Alarm Trigger(Ø3.5 Jack)
PC Audio Input (Ø3.5 Jack)
Power Input (DC 12V, 5A)
Input Connector
x1
x1
x1
x1
x 1 sets
x1
x1
x1
Video Output(BNC) x 1
S-Video
x1
Output Connector
Mechanical & Electrical Design
PIP & PBP
Video Output Looping
3D Comb Filter+De-Interlace
Power Failure Auto Recovery
Anti Burn-in
Alarm Trigger
Source Lock
3DNR (3D Noise Reduction)
Pro 5 Image Ratio
VESA Mounting
Front Bezel Material
Back Cabinet Material
Stand Material
Speaker Output
Power Input
Power Consumption
Working Temperature
Working Humidity
Unit Dimension(WxHxD)
Packing Dimension(WxHxD)
Net Weight
Gross Weight
Regulatory
Color
35W
520 x 380 x170 mm
596 x 500 x 213 mm
7.4 Kg
9.8 Kg
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
100 x 100 mm
Metal
Metal
Metal
5W x 2
DC12V, 5A
30W
5~+40
20% ~ 85%RH
520 x 380 x 170 mm
596 x 500 x 213 mm
6.6 Kg
9.0 Kg
CE,FCC,RoHS
Black
℃
24

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement