ADJ Inno Pocket Spot Pearl Specifications

Inno Pocket Spot Model: Specifications
Inno Pocket Spot
Voltage:
100 - 240V, 50/60Hz
LED:1 x 12W White LED
Power Consumption:
26W @ 120V
27W @ 230V
Dimensions: 6.25”(L) x 5.75”(W) x 10.5”(H)
159mm x 147mm x 265mm
Weight:
7 Lbs. / 3 kgs.
Beam Angle:
13 Degrees
Fuse:2 Amp
Duty Cycle:None
DMX: 2 DMX Channel Modes: 9 Channel Mode & 11 Channel Mode
Colors:7 + White
Gobos:
7 + Spot
Sound Active:Yes
Working Position:
Any Safe, Secure Position
Warranty:
2 Year (730 days)
INNO POCKET SPOT
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged
into the power source.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
User Instructions
Rev. 3/14
©2013 ADJ Products, LLC all rights reserved. Information,
specifications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product.
Inno Pocket Spot C
Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested
repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC
will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn off all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LEDs and lamps)
• Laser Products = 90-Day Limited Warranty
• L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 26
Inno Pocket Spot
Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
Inno Pocket Spot Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Always be sure to dry all parts completely before plugging the unit back in.
Inno Pocket Spot Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1.
Be sure the external fuse has not blown. The fuse is located on the rear panel of the unit.
2.Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
Inno Pocket Spot General Information
Unpacking: Thank you for purchasing the Inno Pocket Spot by ADJ
Products, LLC. Every Inno Pocket Spot has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your fixture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without
contacting customer support first.
Introduction: The Inno Pocket Spot is a DMX intelligent, moving
head, mini LED fixture. The Inno Pocket Spot can operate as a stand
alone fixture or in a Master/Slave configuration. The Inno Pocket Spot
has three operating modes; a sound active, show mode, DMX controlled. This fixture is suitable for theaters, studios, retail stores, and
other similar locations. For best results use fog or special effects smoke
to enhance the beams projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 25
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 2
Distance(m)
Distance(m)
LUX
7600
2150
960
380
240
11
0
Inno Pocket Spot 1.0
2.0
3.0
4.0
)
General Instructions
5.0
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual
with the unit, for future reference.
LED-SC25
Inno Pocket Spot 0
0m(
•
•
•
•
•
•
•
•
Features
DMX-512 Protocol Compatible (9 DMX Channels
or 11 Channels)
0m( )
7 Colors + White
Fixed1.0Gobo Wheel
with 3.0
7 Gobos +4.0Spot 5.0
2.0
3 Operating Modes - Sound Active, Show Mode, & DMX Control
Internal Microphone
Digital Display for Address and Function Setting
4 Preprogrammed Shows
UC-IR Compatiable (Not Included)
Inno Pocket Spot Inno Pocket Spot
Photometric Chart
INNO POCKET SPOT
0m(
13
Distance(m)
0
1.0
2.0
3.0
4.0
Inno Pocket Spot
5.0
6.0
Dimmer Curve Chart
Warranty Registration
The Inno Pocket Spot carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www. adjproducts.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.
780
356
207
143
60
Distance(m)
Ramp Effect
0
1.0
2.0
(Fade Time)
3.0
4.0
0m(
)
5.0
(Fade Time)
Standard
Stage
Inno Pocket Spot Handling Precautions
Caution! There are no user serviceable parts inside this unit. Do not
TV
Architectural
Theatre
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to this unit.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 3
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 24
)
Inno Pocket Spot
Channel
6
7
8
9
10
11
Value
190 - 193
194 - 255
0-7
8 - 15
16 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
0 - 255
0 - 255
1 - 69
70 - 79
80 - 89
90 - 99
100 - 109
110 - 119
120 - 129
130 - 199
200 - 209
210 - 249
250 - 255
0 - 41
42 - 84
85 - 127
128 - 170
171 - 213
214 - 255
11 Channel Mode
Function
STOP
GOBO SCROLL SLOW - FAST
SHUTTER/STROBE
BLACKOUT
SHUTTER OPEN
STROBING SLOW - FAST
SHUTTER OPEN
SHUTTER SLOW OPEN - FAST CLOSE
SHUTTER OPEN
SHUTTER FAST OPEN - SLOW CLOSE
SHUTTER OPEN
RANDOM STROBE
SHUTTER OPEN
DIMMER 0% - 100%
MOVEMENT SPEED FAST - SLOW
FUNCTION
NO FUNCTION
BLACKOUT WITH PAN/TILT
NO BLACKOUT WITH PAN/TILT
BLACKOUT WITH COLOR CHANGE
NO BLACKOUT WITH COLOR CHANGE
BLACKOUT WITH GOBO CHANGE
NO BLACKOUT WITH GOBO CHANGE
NO FUNCTION
RESET ALL
NO FUNCTION
SOUND ACTIVE MODE
DIMMER CURVES
STANDARD
STAGE
TV
ARCHITECTURAL
THEATER
DEFAULT TO UNIT CURVE SETTING
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 23
Inno Pocket Spot Safety Precautions
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Be sure that the local power outlet match that of the required voltage for your unit.
•Do not attempt to operate this unit if the power cord has been
frayed or broken.
•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 25 for cleaning details.
•Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 4
Inno Pocket Spot Mounting
When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attachment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these
qualifications, do not attempt the installation yourself.
Inno Pocket Spot
Channel
1
2
3
4
5
The installaiton should be checked by a skilled person once a year.
6
The Inno Pocket Spot is fully operational in two different mounting
positions, hanging upside-down from a ceiling or set on a flat level
surface. To avoid internal damage to the unit, never mount the unit on
its side as illustrated above. Be sure this fixture is kept at least 0.5m
away from any flammable materials (decoration etc.). Always use
and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails (see next
page).
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 5
Value
0 - 255
0 - 255
0 - 255
0 - 255
0-7
8 - 14
15 - 21
22 - 28
29 - 35
36 - 42
43 - 49
50 - 56
57 - 127
128 - 189
190 - 193
194 - 255
0-7
8 - 15
16 - 23
24 - 31
32 - 39
40 - 47
48 - 55
56 - 63
64 - 71
72 - 79
80 - 87
88 - 95
96 - 103
104 - 111
112 - 119
120 - 127
128 - 189
11 Channel Mode
Function
PAN MOVEMENT 8bit
PAN FINE 16bit
TILT MOVEMENT 8bit
TILT FINE 16bit
COLORS
WHITE
RED
ORANGE
YELLOW
GREEN
BLUE
LIGHT BLUE
PINK
SPLIT COLORS
COLOR SCROLL FAST - SLOW
STOP
COLOR SCROLL SLOW - FAST
GOBO WHEEL
OPEN
GOBO 1
GOBO 2
GOBO 3
GOBO 4
GOBO 5
GOBO 6
GOBO 7
OPEN SHAKE
GOBO 1 SHAKE
GOBO 2 SHAKE
GOBO 3 SHAKE
GOBO 4 SHAKE
GOBO 5 SHAKE
GOBO 6 SHAKE
GOBO 7 SHAKE
GOBO SCROLL FAST - SLOW
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 22
Inno Pocket Spot
Channel
5
6
7
8
9
Value
0-7
8 - 15
16 - 131
132 - 139
140 - 181
182 - 189
190 - 231
232 - 239
240 - 247
248 - 255
0 - 255
0 - 255
0 - 69
70 - 79
80 - 89
90 - 99
100 - 109
110 - 119
120 - 199
200 - 209
210 - 249
250 - 255
0 - 41
42 - 84
85 - 127
128 - 170
171 - 213
214 - 255
9 Channel Mode
Function
SHUTTER/STROBE
BLACKOUT
SHUTTER OPEN
STROBING SLOW - FAST
SHUTTER OPEN
SHUTTER SLOW OPEN - FAST CLOSE
SHUTTER OPEN
SHUTTER FAST OPEN - SLOW CLOSE
SHUTTER OPEN
RANDOM STROBE
SHUTTER OPEN
DIMMER 0% - 100%
MOVEMENT SPEED FAST - SLOW
FUNCTION
NO FUNCTION
BLACKOUT WITH PAN/TILT
NO FUNCTION
BLACKOUT WITH COLOR CHANGE
NO FUNCTION
BLACKOUT WITH GOBO CHANGE
NO FUNCTION
RESET ALL
NO FUNCTION
SOUND ACTIVE MODE
DIMMER CURVES
STANDARD
STAGE
TV
ARCHITECTURAL
THEATER
DEFAULT TO UNIT CURVE SETTING
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 21
Inno Pocket Spot Mounting
NOTICE: The suitable enviromental temperature for this lighting fixture is between -25˚ C to 45˚ C. Do not place this lighting
fixture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the fixture
to run at its best and help prolong the fixture life.
Screw one clamp via a M12 screw and nut to the included
bracket. Attach the bracket using the included screws to the
bottom of the Inno Pocket Spot. Attach the eyehole screw to
the bottom of the base and pull the safety-cable through the
screw and over the trussing system or a safe fixation spot.
Insert the end in the carabine and tighten the safety screw.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 6
Inno Pocket Spot
DMX Set Up
Power Supply: The ADJ Inno Pocket Spot contains a automatic voltage switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
Inno Pocket Spot
Channel
1
2
3
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Inno Pocket Spot can be controlled via DMX-512 protocol. The Inno Pocket Spot two DMX channel modes; 9 channel mode
& 11 channel mode. The DMX address is set electronically using the controls on the front panel of
the unit. Your unit and your DMX controller require
a approved DMX-512 110 Ohm Data cable for data
input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased at
Figure 1
almost all professional sound and lighting stores).
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 7
4
Value
0 - 255
0 - 255
0-7
8 - 14
15 - 21
22 - 28
29 - 35
36 - 42
43 - 49
50 - 56
57 - 127
128 - 189
190 - 193
194 - 255
0-7
8 - 15
16 - 23
24 - 31
32 - 39
40 - 47
48 - 55
56 - 63
64 - 71
72 - 79
80 - 87
88 - 95
96 - 103
104 - 111
112 - 119
120 - 127
128 - 189
190 - 193
194 - 255
9 Channel Mode
Function
PAN MOVEMENT 8bit
TILT MOVEMENT 8bit
COLORS
WHITE
RED
ORANGE
YELLOW
GREEN
BLUE
LIGHT BLUE
PINK
SPLIT COLORS
COLOR SCROLL FAST - SLOW
STOP
COLOR SCROLL SLOW - FAST
GOBO WHEEL
OPEN
GOBO 1
GOBO 2
GOBO 3
GOBO 4
GOBO 5
GOBO 6
GOBO 7
OPEN SHAKE
GOBO 1 SHAKE
GOBO 2 SHAKE
GOBO 3 SHAKE
GOBO 4 SHAKE
GOBO 5 SHAKE
GOBO 6 SHAKE
GOBO 7 SHAKE
GOBO SCROLL FAST - SLOW
STOP
GOBO SCROLL SLOW - FAST
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 20
REMOTE
CONTROL
INPUT
SOUND
Inno Pocket Spot
Remote Operation
INPUT
OUTPUT
Inno Pocket Spot
The UC-IR infrared remote gives you control of various functions
(See below). To control the fixture you must aim the remote at the
front of the fixture and be no more then 30 feet away.
POWER
COMMON
DMX512 OUT
3-PIN XLR
STROBE - This button will activate the strobe effect. You can control
the flash rate by pressing the “DIMMER +” and “DIMMER -” buttons.
If you press and hold this button the unit will begin to strobe.
OUTPUT
INPUT
OUTPUT
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 19
1
DMX512 IN
3-PIN XLR
2
3
1
2
XLR Pin Configuration
Pin 1 = Ground
REMOTE
CONTROL
INPUT
OUTPUT
INPUT
Pin 2
= Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
Special Note: Line Termination. When longer runs of cable are
POWER
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
COMMON
DMX -
3
Figure 3
DMX+,DMX-,COMMON
2
1 Ground
SOUND
3 Hot
SHOW - This activates the show mode. Use the “DIMMER +” and
“DIMMER -” buttons to scroll through the 4 shows. DMX512
DMX +
DMX -
2 Cold
2 Cold
REMOTE
CONTROL
INPUT
SOUND
POWER
3
2
DMX +
3
XLR Female Socket
XLR Male Socket
1 Ground
SOUND ON & OFF - These buttons activate and deactivate the
sound active mode.
DMX512 OUT
3-PIN XLR
1
Figure 2
1-9 - When in either Gobo mode or Color mode, these buttons will
allow you to select either a gobo or color.
1
POWER
DMX+,DMX-,COMMON
cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
“DIMMER +” and “DIMMER -” - Use these buttons to adjust the output intensity and to adjust the strobe speed.
COLOR - Press this button to enter Dimmer mode. Use the 1-9 buttons to select your desired color. Adjust the output intensity using the
“DIMMER +” and “DIMMER -” buttons.
SOUN
Notice: Be sure to follow
figures two and three when making your own
DMX512
FADE/GOBO - Press this button to enter Gobo mode. Use the 1-9
buttons to select your desired gobo. Adjust the output intensity using
the “DIMMER +” and “DIMMER -” buttons.
INPUT
OUTPUT
Your cables should be made with a male and female XLR connector on
either end of the cable. Also remember that DMX cable must be daisy
chained and cannot be split.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
REMOTE
CONTROL
INPUT
INPUT
DMX Set Up
STAND BY - Pressing this button will blackout the fixture.
SOUND
REMOTE
CONTROL
INPUT
SOUND
3
1
2
DMX512 IN
3-PIN XLR
3
1
2
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 8
Termination
avoids sign
and interfere
to connect a
120 Ohm 1/4
and PIN 3 (
Inno Pocket Spot
DMX Set Up
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Pin 4 - Do Not Use
Not Used
Pin 5 - Do Not Use
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 9
Inno Pocket Spot
Master-Slave Set Up
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth- er via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit press the MENU button until “SLND” is dis-
played, and press ENTER. Use the UP and DOWN buttons to scroll to the “MAST” setting and press ENTER.
3. After setting the Master unit to the master setting find your desired operating mode.
4. On the slave units press the MENU button until “SLND” is dis-
played, and press ENTER. Choose either “SL 1” or “SL 2” and press ENTER. See page 10 for more info.
5. The slave units will now follow the Master unit.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 18
Inno Pocket Spot
Operation
Universal DMX Control: This function allows you to use a Elation®
Inno Pocket Spot
System Menu
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Inno Pocket Spot has 2 DMX channel modes; 9 channel mode or 11 channel mode. See pages 20-23 for detailed descrip-
tion of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 9 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
DMX 512 Address Setting
Channel Mode
Show Mode
Dimmer Mode
Slave Mode
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until “SOUN” is displayed, and press ENTER. Press the UP or DOWN buttons so that “ON” is dis-
played and press ENTER.
2. Press the MENU button until “SENS” is displayed, and press ENTER. Use the UP and DOWN buttons to adjust the sound
sensitivity. Press ENTER when you have found your desired sensi-
tivity level.
Lost DMX Signal
Sound Mode
Sound Sense
Pan Inverse
Show Mode: This mode allows either a single unit or several units
linked together, to run one of four shows that you choose.
1. Press the MENU button until “SHND” is displayed, and press ENTER.
2. Press the UP or DOWN buttons until you find your desired show, and press ENTER.
Tilt Inverse
LED Display
Display Normal
Display Inversion
Auto Test
Fixture Use Time
Firmware Version
Reset
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 17
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 10
Inno Pocket Spot
System Menu
System Menu: When making adjustments press ENTER to
confirm your setup then press and hold the MENU button
for at least 3 seconds. To exit without making any adjustments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.
ADDR - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is
displayed, press ENTER.
2. The current address will now be displayed and flashing. Press the
UP or DOWN buttons to find your desired address. Press ENTER to
set your desired DMX address.
CHND - This will let select your desired DMX channel
mode.
1. Press the either the MENU button until “CHND” is displayed, press
ENTER. Either “9CH” or “11CH” will be displayed
2. Press the UP or DOWN buttons to find your desired DMX channel
mode and press ENTER to confim and exit.
SHND - Show modes 0-4 (Factory programs). Show
Inno Pocket Spot
Home Adjustment Menu
OTIL - Adjustment of the tilt position.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OTIL” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
OGOB - Adjustment of the gobo wheel.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OGOB” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
OCOL - Adjustment for the color wheel.
1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “OCOL” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
mode can run with or without sound active mode active.
1. Press the MENU button until “SHND” is displayed, press ENTER.
2. “Sh X” will now be displayed, “X” representing a number between
0-4. Shows 1-4 are factory programs, while show “0” is random mode.
Use the UP or DOWN buttons to find your desired show.
3. When you have found your desired show press ENTER, then press
and hold the MENU button for at least 3 seconds to activate. After
you have set your desired show, it can be changed at any time using
the UP or DOWN buttons.
DIND - This will let select your desired dimmer curve.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 11
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 16
Inno Pocket Spot
System Menu
the unit.
1. Press the either the MENU button until “VER” is displayed, press
ENTER.
2. The display will show the software version.
RSET - Use this function to reset the unit.
1. Press the MENU button until “RSET” is displayed, press ENTER.
2. The fixture will now reset.
Inno Pocket Spot
Home Adjustment Menu
Inno Pocket Spot
System Menu
1. Press the either the MENU button until “DIND” is displayed, press
ENTER. 1 of 5 dimmer curves will be displayed. “STDA” (standard),
“STGE” (stage), “TV” (TV), “ARAL” (theatrical), or “THAL” (Architectural).
2. Press the UP or DOWN buttons to find your desired dimmer curve
and press ENTER to confim and exit.
SLND - This will let you set unit as a master or slave in a
master/slave configuration.
1. Press the MENU button until “SLND” is displayed, press ENTER.
Either “MAST”, “SL 1”, or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim.
NOTE: In a Master/Slave configuration you can set one fixture to
Master and then set the next fixture to “SL 2”, the fixtures will now
have contrast movement to each other.
LOST - This mode can be used as a precaution mode, that
To enter the home position adjustment menu, press the ENTER
button for at least 5 seconds. In this submenu you are able to adjust
the original position of the pan position, tilt position, color wheel position, and gobo wheel position.
OPAN - Adjustment of the pan position.
1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OPAN” is displayed, press ENTER.
2. Use the UP and DOWN buttons to make your adjustments, and
then press ENTER to confirm. Press the MENU button for one second
to exit.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 15
in case the DMX signal is lost, interrupted, or power is lost,
the operating mode chosen in the setup is the running mode
the fixture will go into when the DMX signal is lost. You can
also set this as the operating mode you would like the unit to
return to when power is applied.
1. Press the MENU button until “LOST” is displayed, and either
“HOLD”, “SHND”, or “BLAC” will be displayed beneath.
2. Press ENTER and the bottom choice will begin to flash. Use the UP
or DOWN buttons to choose an operating mode you would like the unit
to start up in when power is applied or the DMX signal is lost.
• Hold - If the DMX signal is lost the fixture will stay in the last DMX setting. If power is applied and this mode is set, the unit will automatically
go into the last DMX set up.
• SHND (Show Mode) - If the DMX signal is lost, interrupted, the unit
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 12
Inno Pocket Spot
System Menu
will automatically go into show mode.
• BLAC (Blackout) - If the DMX signal is lost or interrupted, the unit will
automatically go into stand by mode.
3. Press ENTER to confirm your desired set up.
SOUN - Sound Active mode.
1. Press the MENU button until “SOUN” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode, or
“OFF” to deactivate sound active mode.
3. Press ENTER to confirm.
SENS - In this mode you can adjust the sound sensitivity.
1. Press the MENU button until “SENS” is displayed, press ENTER.
2. A number between 0-100 will be displayed. Press the UP or DOWN
buttons to adjust the sound sensitivity. 0 being the least sensitive,
and 100 being the most sensitive.
3. When you have found your desired setting press ENTER to confirm.
PINT - Pan Inversion
1. Press the MENU button until “PINT” is displayed, press ENTER.
Either “Yes” or “No” will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to confim. To deactivate Pan inversion, select “No” and press Enter.
TINT - Tilt Inversion
1. Press the MENU button until “TINT” is displayed, press ENTER.
Either “Yes” or “No” will be displayed.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 13
Inno Pocket Spot
System Menu
2. To activate the tilt inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to confim. To deactivate tilt inversion, select “No” and press Enter.
LED - With this function you can have the LED display
turn off after 10 seconds.
1. Press the MENU button until “LED” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at all
times, or “OFF” to switch to have the LED display switch off after 10
seconds.
3. Press ENTER to confirm. To make you LED display reappear again
press any button.
DISP - This function will reverse the display 180º.
1. Press the MENU button until “DISP” is displayed, press ENTER.
2. Press ENTER to “flip” the display. Press ENTER to “flip” it again.
Press ENTER when you have made your desired setup.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press ENTER.
2. The fixture will now run a self test.
FHRS - With this function you can display the running
time of the unit.
1. Press the MENU button until “FHRS” is displayed, press ENTER.
2. The running time of the fixture will now be displayed. Press MENU
to exit.
VER - Use this function to display the Software version of
ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 14