Quadra-Fire FG21SP-LP Owner`s manual

Owner’s Manual
Installation and Operation
Models: FG21SP-NG
FG21SP-LP
Decorative Gas Log Set
For Use With The Fogata
Grande only
Tested and
Listed by
C
O-T L
OMNI-Test Laboratories, Inc.
DO NOT DISCARD THIS MANUAL
• Important operating and • Read, understand and follow • Leave this manual with
party responsible for
maintenance instructions these instructions for safe
installation and operation.
use and operation.
included.
T
O
N RD
O A
D SC
I
D
CAUTION
WARNING
WARNING
If the information in these instructions is not followed exactly, a
fire may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas:
- Do not try to light any appliance.
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or
the gas supplier.
Beaverton
Oregon USA
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Cast iron and other surfaces are hot during
operation and cool down.
• Keep children away.
• CAREFULLY SUPERVISE children around the firepit.
• Alert children and adults to hazards of high
temperatures.
• Keep clothing, furniture, draperies and other
combustibles away.
Quadra-Fire • Fogata Grande
Installation and service of this appliance should be performed
by qualified personnel. Hearth & Home Technologies
suggests NFI certified or factory-trained
professionals, or technicians supervised
by an NFI certified professional.
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
Congratulations
Congratulations on selecting a Quadra-Fire decorative gas
log set. The Fogata Grande you have selected is designed to
provide the utmost in safety, reliability, and entertainment.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a Fogata Grande, you’ll want to read and
carefully follow all of the instructions contained in this owner’s
manual. Pay special attention to all cautions and warnings.
Your new Fogata Grande will give you years of durable use
and trouble-free enjoyment. Welcome to the Quadra-Fire
family of appliance products!
This owner’s manual should be retained for future reference.
We suggest you keep it with your other important documents
and product manuals.
Homeowner Reference Information
We recommend that you record the following pertinent
information about your appliance:
Model Name: Date purchased/installed: Serial Number: Location on appliance: Dealership purchased from: Dealer phone: Notes: Listing Label Information/Location
The model information regarding your specific appliance can be found on the rating plate located in the control area of the
appliance.
Tested and
Listed by
C
O-T L
Beaverton
Oregon USA
OMNI-Test Laboratories, Inc.
Quadra-Fire
LISTED
OUTDOOR
GAS FIREPLACE
20802 Kensington Blvd
Lakeville, MN 55044
Models: FG21SP-NG
FG21SP-LP
Outdoor Gas Fireplace
Type of Gas:
MFG. DATE: Serial #:
Min. Gas Supply for input Adj.
Max. Gas Supply:
Manifold Pressure:
WARNING: Must Not Be Used For Cooking
WARNING: For Outdoor Use Only
MINIMUM CLEARANCES: Bottom: 0 inch Top: 8 Ft. Minimum clearances from side and back of unit to adjacent combustible construction below top of unit, 24 inches from side and 24 inches
from back. Minimum horizontal clearances from sides and back of unit to adjacent vertical combustible construction extending above top
of unit, 24 inches from sides and 24 inches from back. This apliance must be installed in accordance with local codes, if any. If none, follow ANSI Z223.1 installation codes
Quadra-Fire • Fogata Grande
Table of Contents
1 Listing and Code Approvals
A. Appliance Certification. . . . . . . . . . . . . . . . . . . . . . . . . . B. BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . C. High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . 2 Getting Started
A. Design and Installation Considerations. . . . . . . . . . . . . B. Tools and Supplies Needed. . . . . . . . . . . . . . . . . . . . . . C. Inspect the Appliance and Components . . . . . . . . . . . . 3 Framing and Clearances
A. Select Appliance Location. . . . . . . . . . . . . . . . . . . . . . . B. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C. Framing Enclosure for LP Gas Supply System . . . . . . . . 4 Gas Information
A.
B.
C.
D.
E.
Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gas Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . LP Gas Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Finishing
6 Appliance Setup
7 Operating Instructions
8 Troubleshooting
A. Burner Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B. Log Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.
B.
C.
D.
Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . Lighting the Appliance. . . . . . . . . . . . . . . . . . . . . . . . . . After the Appliance is Lit . . . . . . . . . . . . . . . . . . . . . . . . Frequently Asked Questions. . . . . . . . . . . . . . . . . . . . . 9 Maintaining and Servicing the Appliance 10Reference Materials
A.
B.
C.
D.
Quadra-Fire • Fogata Grande
Service Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Components. . . . . . . . . . . . . . . . . . . . . . . . . . Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . Contact Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Listing and Code Approvals
A.Appliance Certification
B.BTU Specifications
MODELS: Fogata Grande
LABORATORY: OMNI
TYPE: Decorative Gas Log Set
STANDARD: IAS US requirements for Outdoor
Gas Fireplaces, Draft 4-96 and ANSI Z21.58-1995/
CGA 1.6­ M96
The Fogata Grande has been tested in accordance with
IAS US requirements for Outdoor Gas Fireplaces,
Draft 4‑96 and ANSI Z21.58‑1995/CGA 1.6-M96 for Canada and has been listed by OMNI for installation and operation as described in these installation and operating instructions.
The installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas Code
ANSI Z223.1 or CAN/CGA‑B149.1, National Gas Installation Code or CAN/CGA‑B149.2, Propane Installation
Code.
Quadra-Fire • Fogata Grande
Model
FG21SP-NG
FG21SP-LP
Max Input
BTUH
Orifice Size
2
Getting Started
This appliance is a Decorative Gas Log Set for OUTDOOR
USE ONLY and MUST NOT be used for cooking.
Place the Fogata Grande on a flat and stable non-combustable surface in an outdoor location such as a patio. This
location must be adjacent to the gas supply line. DO NOT
locate the appliance where it can get excessively wet or
submerged in water.
WARNING
Do NOT use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
A.Design and Installation Considerations
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• Where the appliance is to be installed. See Sections 3
and 4.
• Gas supply piping. See Section 5.
• Framing and finishing details. See Sections 3 and 4.
B.Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional,
state and national codes and regulations.
• Consult insurance carrier, local building, fire
officials or authorities having jurisdiction about
restrictions, installation inspection, and permits.
Gloves
Safety glasses
Flat blade screwdriver
Non-corrosive leak check solution
Wrenches
Drill and hex head drivers
Masonry drill bit
WARNING
Asphyxiation Risk
• This gas log set is for outdoor use in a wellventilated space.
• Log set must not be installed inside an
enclosed structure or unvented appliance.
CAUTION
WARNING
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
• Installation and use of any damaged components.
• Modification of the burner or log assemblies.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
Any such action may cause a fire hazard.
Quadra-Fire • Fogata Grande
Sharp Edges
• Wear protective gloves
and safety glasses during
installation.
C.Inspect the Appliance and Components
WARNING
Inspect appliance and components for
damage. Damaged parts may impair safe
operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
• Carefully remove the appliance and components from the
packaging
• The gas logs may be packaged separately and must be
field installed.
• Report to your dealer any parts damaged in shipment.
• Read all of the instructions before starting the
installation. Follow these instructions carefully
during the installation to ensure maximum safety and
benefit.
Report damaged parts to dealer.
Burner Assembly
Valve Control Box Assembly
Quadra-Fire • Fogata Grande
3
Framing and Clearances
Note:
• Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
WARNING
Fire Risk
Provide adequate clearance:
• Around air openings.
• For service access.
Locate appliance away from traffic areas.
A.Select Appliance Location
When selecting a location for your appliance it is important
to consider the required clearances to all combustibles.
B. Clearances
Place the Fogata Grande on a flat stable surface. The clearance requirements to any combustible material, to any side,
is a minimum of 24 inches.
Combustible materials are not allowed over the top of the
Fogata Grande. Clearances
10'
10'
Non-combustible
Quadra-Fire • Fogata Grande
4
Appliance Set Up
1) After placing the Fogata Grande in the desired location,
locate the oval hole in the fire bowl and be sure it is positioned towards the leg where the gas connection is to be
made.
Figure 3
Figure 1
2) With the letters provided, using tape, identify leg “A” as
the leg to which the gas valve assembly will be attached.
4) Take the pilot assembly, Figure 3, and locate the label on
the burner that indicates the location for the pilot assembly. Insert the pilot hood over the burner tube and slide it forward
so the top front clip slides over the tube of the burner. The
lower bracket on the right side will need to be bent up with
pliers to lock the pilot hood in place.
Moving counter clock wise, lable the remaining legs “B”, “C”
and “D” as shown in Figure 1. This will assit you in installing
the logs after the gas connections have been made.
Figure 2
3) As shown in Figure 2, lay leg “A” on its face (on a smooth
non abrasive surface to prevent damaging the surface) to
begin the assembly of the gas system.
As show, place the gas valve control box on the inside of leg
“A”. Locate the open end of the box assembly 1/2 inch back
from the edge of the leg as shown in Figure 1.
Next position the top flange with the two key hole anchoring holes approximately 3/4 inch down from the seam as
shown. Secure the two masonry screws through the top of
the holes provided into the leg. Do not completely tighten
since the control box will need to be removed in order to
complete the final installation.
Once the screws have been installed, remove the valve
control box in order to assemble the other componenets.
Figure 4
5) Place the stainless steel grate (heavy round bar grate,
supplied with fire pit) in position in the lower part of the bowl. This grate will rest on top of the lower tabs.
Next place the screen over the grate so that the oval opening in the screen lines up with the direction of the stainless
bars on the grate as shown in Figure 4.
Feed the burner flex line, pilot tube and piezo ignitor wire
down through the center of the screen and grate and through
the oval hole in the side of the bowl
The burner will rest flat on the upper tabs on the inside of
the bowl. Quadra-Fire • Fogata Grande
6) With the valve control box under the edge of the bowl,
connect the pilot tube in the hole as shown in picture.
The stainless steel flex connector is to be connected to the
brass elbow located on the top of the valve control box.
The piezo ignitor lead is to be connected to the ignitor lead
coming out of the valve control box.
Thermopile
8) Replace leg “A” under the Fogata Grande bowl and secure the valve control box on the two screws previously installed in step 3
Figure 5
7) Feed the thermopile up through the oval hole in the bowl
and insert it into the open hole in the pilot assembly. Ensure
that the thermopile snaps into place and is securly in position to ensure proper connection.
9) With all the gas componets now securly in place, take
the lava rock supplied and spread it over the screen so that
it covers the sides of the burner but ensure it does not cover
the top of the burner in order to ensure proper flame
10) Log Instalation and placement instructions for the log set
are provided with the log set
Quadra-Fire • Fogata Grande
5
Gas Information
A.Fuel
WARNING
Before making gas connections ensure appliance being installed is compatible with the available gas type.
Fire Risk
Explosion Risk
• Gas build-up during line purge may
ignite.
• Purge should be performed by qualified
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such
as sparks or open flames.
B.Gas Pressure
Proper input pressures are required for optimum appliance
performance. Gas line sizing requirements need to be made
following NFPA51.
WARNING
Fire Risk
Explosion Risk
Verify inlet pressures.
• H i g h p r e s s u r e m a y c a u s e o v e r f i r e
condition.
• Low pressure may cause explosion.
• Verify minimum pressures when other
household gas appliances are operating.
Install regulator upstream of valve if line
pressure is greater than 1/2 psig.
• Incoming gas line should be piped to the 1/2 in.
connection.
• A small amount of air will be in the gas supply lines.
When first lighting appliance it will take a short time
for air to purge from lines. Subsequent lighting of the
log set will not require such purging.
Pressure requirements for appliance are shown in table below. Minimum pressures must be met when other household
gas appliances are operating.
Pressure
Natural Gas
Propane
Minimum Inlet Pressure
5.0 in. w.c.
11.0 in. w.c.
Maximum Inlet Pressure
7.0 in. w.c.
14.0 in. w.c.
C.Gas Connection
Note: Have the gas supply line installed in accordance
with local building codes, if any. If not, follow ANSI
223.1. Installation should be done by a qualified installer
approved and/or licensed as required by the locality. (In
the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.)
Note: A listed (and Commonwealth of Massachusetts
approved) 1/2 in. (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 in.
(13 mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
10
Quadra-Fire • Fogata Grande
WARNING
CHECK FOR GAS LEAKS
Fire Risk
Explosion Risk
Asphyxiation Risk
• Check all fittings and connections.
• Do not use open flame.
• After the gas line installation is complete,
all connections must be tightened and
checked for leaks with a commercially
available, non-corrosive leak check
solution. Be sure to rinse off all leak check
solution following testing.
Fittings and connections may have loosened
during shipping and handling.
D.Gas Pressure
Proper input pressures are required for optimum appliance
performance. Gas line sizing requirements need to be made
following NFPA51.
WARNING
Fire Risk
Explosion Risk
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
WARNING
CHECK FOR GAS LEAKS
• Gas Supply Pressure: Minimum inlet gas supply pressure
must be 4.5 in. W.C. for natural gas or 11 in. W.C. for LP
gas for the purpose of input adjustment. Maximum inlet
gas pressure must not exceed 7.0 in. W.C. for natural
gas or 13 in. W.C. for LP gas. The gas line supplying the
appliance must be sufficient size to furnish the appropriate
supply pressure to the appliance while operating in the
“High” setting. (Minimum line ID of 1/2 in. required if the
line is longer than 20 ft.
• Gas Line Pressure Test: Perform pressure test according
to state and local code (if pressure exceeds 1/2 in. psi [3.5
kPa]) before appliance is connected. Be sure to release
air pressure from the gas line before connection is made
to the appliance. Excessive pressure will damage the gas
control and may cause a gas leak.
• Gas Leak Test: Make sure the gas connections are tight.
Turn on the gas and coat each joint with a non-corrosive
gas leak check solution. Air bubbles will form indicating
any leaks. DO NOT USE A FLAME OR ANY TYPE OF
IGNITION SOURCE TO CHECK FOR LEAKS. All leaks
must be corrected before proceeding with installation.
Fire Risk
Explosion Risk
Asphyxiation Risk
• Check all fittings and connections.
• Do not use open flame.
• After the gas line installation is complete,
all connections must be tightened and
checked for leaks with a commercially
available, non-corrosive leak check
solution. Be sure to rinse off all leak check
solution following testing.
Fittings and connections may have loosened
during shipping and handling.
WARNING
Fire Risk
Explosion Risk
Do NOT change the valve settings.
• This valve has been preset at the
factory.
• Changing valve settings may result in fire
hazard or bodily injury.
WARNING
Shock Risk
Explosion Risk
Do NOT wire 110V to valve.
11
Quadra-Fire • Fogata Grande
E.High Altitude Installations
OMNI gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 ft in the USA
and Canada.
When installing this appliance at an elevation above 2000 ft,
it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size. Input rate
should be reduced by 4% for each 1000 ft above a 2000 ft
elevation in the U.S.A., or 10% for elevations between 2000
and 4500 ft in Canada. If the heating value of the gas has
been reduced, these rules do not apply. To identify the proper orifice size, check with the local gas utility.
If installing this appliance at an elevation above 4500 ft (in
Canada), check with local authorities.
12
Quadra-Fire • Fogata Grande
6
Operating Instructions
A.Before Lighting Appliance
WARNING
• Before lighting this appliance, ensure the manual shutoff
valve is open.
Do NOT use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
Before operating this appliance, have a qualified
technician:
WARNING
• Inspect the burner before each use of the gas log set. If
there is any evidence that the burner is damaged, it must
be replaced before operating.
• Review proper placement of logs.
• Ensure that there are no gas leaks.
• Ensure that the flow of combustion and ventilation air is
not obstructed.
•
•
•
WARNING
•
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer
to the owner’s information manual provided with this
appliance. For assistance or additional information consult
a qualified installer, service agency or the gas supplier.
Fire Risk
Burn Risk
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT
Glass and other surfaces are hot during
operation and cool down.
Keep children away.
CAREFULLY SUPERVISE children in same room as
appliance.
Alert children and adults to hazards of high
temperatures.
Keep clothing, furniture, draperies and other
combustibles away.
Piezo
Valve Control
Knob
On/Off Switch
WARNING
The lighting instructions and operation of the unit are
described on the following instructional page and MUST be
followed to ensure the safe operation of this appliance.
13
Quadra-Fire • Fogata Grande
FOR
FOR YOUR
YOUR SAFETY
SAFETY READ
READ BEFORE
BEFORE LIGHTING
LIGHTING
WARNING! IF THESE INSTRUCTIONS ARE NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
A. This appliance has a pilot that must be lighted by hand. When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control handle. Never use tools. If the handle will not push in or turn
by hand, do not try to repair it. Call a qualified service technician. Force or attempted repair may result in fire or
explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system and any gas control that has been under water.
LIGHTING INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
STOP! Read the safety information previously listed above.
Turn gas control handle clockwise
to the “OFF” position.
Wait 5 minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B”
in the safety information above on this label. If you don’t smell gas, go to the next step.
Locate pilot (mounted on the right side of the top burner pan).
Turn control handle counterclockwise
to the “PILOT” position.
Place a lit match at the pilot burner, and simultaneously push in on the control handle. This should ignite the pilot.
Once the pilot lights, continue to depress the control handle for 1 minute.
After 1 minute, slowly release control handle and it will pop back out. Pilot should remain lit. If it goes out, repeat
Steps 1 through 7.
• If the handle does not pop out when released, stop and immediately call your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas control handle to “OFF” and call your service technician
or gas supplier.
Turn gas control handle counterclockwise
to “ON”.
TO TURN OFF GAS TO APPLIANCE
Turn gas control handle clockwise
to “OFF” position. Do not force.
Control Knob
(Shown in “Pilot” Position)
L
UL O
N - OF
N O
Thermocouple
F F
pilot
Pilot Burner Assembly
14
Quadra-Fire • Fogata Grande
B.After the Appliance is Lit
WARNING
Initial Break-in Procedure
When you light the appliance, you may notice that it produces heat which may have an odor or smell. If you feel this
odor is excessive it may require the initial three to four hour
continuous burn on high followed by a second burn up to
12 hours to fully drive off any odor from paint and lubricants
used in the manufacturing process.
Note: This appliance should be run three to four hours on
the initial start-up. Turn it off and let it cool completely. This
will help cure the products used in the paint and logs.
WARNING
Fire Risk
High Temperatures
Keep combustible household items away
from appliance.
• Do NOT obstruct combustion and
ventilation air.
• Do NOT place combustible items on top
of or near appliance.
• Keep furniture, draperies away from
appliance.
15
Quadra-Fire • Fogata Grande
Fire Risk
Keep combustible materials, gasoline and
other flammable vapors and liquids clear of
appliance.
• Do NOT store flammable materials in the vicinity of the appliance.
• Do NOT use gasoline, lantern fuel,
kerosene, charcoal lighter fluid or similar
liquids in this appliance.
Combustible materials may ignite.
7
Troubleshooting
A.Troubleshooting
With proper installation and maintenance, your new decorative gas appliance should provide years of trouble-free service.
If you do experience a problem, refer to the troubleshooting guide below. This guide will assist you or a qualified service
technician in the diagnosis of problems and the corrective action to be taken.
Symptoms
1. A match or piezzo will not
light the pilot.
Possible Causes
A. Main gas shutoff valve is
closed
Corrective Action
1. Make sure that the shutoff valve located on the
incoming gas line is open.
B. There is air in the gas line. 1. Light a match. Turn the valve knob to the “PILOT”
position and depress. Keep the match near the pilot
burner until it lights.
C. The valve knob is in the
“OFF” position.
1. Turn the valve knob to the “PILOT” position and
depress. Keep the match near the pilot burner until it
lights.
D. The pilot orifice is plugged, 1. This repair requires tools and some degree of
not allowing gas to flow.
experience. Call a qualified service technician.
E. There is no gas supply to
the fireplace.
1. Check the plumbing to ensure the fireplace has been
hooked up the gas supply line.
2. The propane tank is empty.
2. The pilot lights, but
will not stay lit after
carefully following lighting
instructions.
A. There is a weak pilot flame 1. The pilot flame must engulf the thermocouple.
Clean and/or adjust the pilot for maximum flame
impingement on the thermocouple.
3. The pilot is on, but there is A. A blockage is preventing
no gas to the main burner;
gas flow.
the valve knob is on.
B. Defective valve.
16
1. Inspect the burner orifice for obstruction. Call a
qualified service technician.
1. Replace the gas valve. Call a qualified service
technician.
Quadra-Fire • Fogata Grande
8
Maintaining and Servicing the Appliance
Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a
qualified service technician should perform an appliance
check-up annually.
WARNING
Annual inspection by qualified technician
recommended.
Check:
• Obstructions of combustion and ventilation
air.
• Condition of logs.
• Condition of burner assembly.
• Burner ignition and operation.
• Burner air shutter adjustment.
• Gas connections and fittings.
Risk of:
• Fire
• Delayed ignition or explosion
• Exposure to combustion fumes
• Odors
WARNING
Risk of injury or property damage
Before servicing:
• Turn off utilities to appliance.
• Ensure appliance is completely cooled.
Maintenance and Service Tasks:
Inspect
Burner Assembly
Logs
Burner ignition and operation
17
Maintenance Tasks
1
Remove logs and examine burner. Vacuum and wipe out dust, cobwebs, debris or pet hair. Use caution
when cleaning these areas. Screw tips that have penetrated the sheet metal are sharp and should be
avoided.
2
Remove any foreign objects
3
Inspect for paint condition, warpage, corrosion. Sand and repaint as necessary.
4
Verify unobstructed air circulation.
1
Inspect for broken, damaged or missing logs. Replace as necessary.
2
Verify correct log placement and no flame impingement causing sooting. Correct as necessary.
3
Verify logs are clean and carbon (soot) free. Logs may be cleaned with a dry bristle brush or dry cloth.
Handle logs with care as they are fragile and easily damaged.
1
Verify all gas connections are tight and leak-free.
2
Clean off burner top corrosion or deterioration. Replace burner if necessary.
3
Check for smooth lighting and ignition carryover to all ports. Verify there is no ignition delay.
4
Inspect for lifting or other flame problems.
5
Inspect orifice for soot, dirt or corrosion.
6
Verify manifold and inlet pressures. Adjust regulator as required.
Quadra-Fire • Fogata Grande
9
Reference Materials
A.Service Parts List
18
Service Parts
Fogata Grande
#
Description of Part
Part Number
1
Valve Assembly Complete
1
2
Thermopile
1
3
Burner Assembly Complete
1
4
Pilot Assembly (without Thermopile)
1
Quadra-Fire • Fogata Grande
Qty.
Service Parts
B.Logs
Log 1
Log 4
Log 7
Fogata Grande
Log 2
Log 3
Log 5
Log 6
Log 8
Log 9
#
Description of Part
1
Log 1
1
2
Log 2
1
3
Log 3
1
4
Log 4
1
5
Log 5
1
6
Log 6
1
7
Log 7
1
8
Log 8
1
9
Log 9
1
19
Part Number
Quadra-Fire • Fogata Grande
Qty.
Service Parts
B.Logs (continued)
Log 10
Log 11
Log 13
Log 14
Log 12
Log 15
Log 17
Log 16
20
Fogata Grande
#
Description of Part
Part Number
1
Log 10
1
2
Log 11
1
3
Log 12
1
4
Log 13
1
4
Log 14
1
5
Log 15
1
6
Log 16
1
7
Log 17
1
Quadra-Fire • Fogata Grande
Qty.
C.Limited Lifetime Warranty
Hearth & Home Technologies Inc.
Outdoor Products Limited One Year Warranty
Hearth & Home Technologies Inc. extends the following warranty for Hearth & Home Technologies outdoor products
used in the United States of America or Canada. Dealers and employees of Hearth & Home Technologies have no
authority to make any warranty or authorize any remedies in addition to or inconsistent with the terms of this warranty.
This warranty gives you specific legal rights. You may also have other rights that vary from state to state.
Hearth & Home Technologies warrants that this Hearth & Home Technologies Outdoor Product (the “Product”) will
be free from defects in material and workmanship for a period of one year from its date of purchase. This warranty is
subject to the conditions, exclusions and limitations described below.
This warranty applies only to the original owner of the Product and is non-transferable. Hearth & Home Technologies’
obligation under this warranty does not extend to damages resulting from (1) assembly, operation or maintenance
of the Product not in accordance with the Installation/Assembly Instructions, Operating Instructions and the Listing
Agency Identification Label furnished with the Product; (2) installation or use which does not comply with local building
codes and ordinances; (3) shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike
repairs; (4) use of fuels other than those specified in the Operating Instructions; (5) Installation or use of components
not supplied with the Product or any other components not expressly authorized and approved in writing by Hearth &
Home Technologies; and/or (6) modification of the Product not expressly authorized and approved in writing by Hearth
& Home Technologies. Any of the circumstances described in the previous sentence voids this warranty. This warranty
is void if the Product or any component has been removed, repaired, or replaced before Hearth & Home Technologies
has been afforded a reasonable opportunity to inspect the Product.
This warranty is limited to the replacement or repair of defective components or workmanship and Hearth & Home
Technologies may fully discharge its obligations under this warranty by repairing or replacing, at its discretion, the
defective components. Hearth & Home Technologies will provide replacement parts at no charge and will pay reasonable
and necessary labor and freight costs related to replacing or repairing defective components under this warranty. The
maximum amount recoverable under this warranty is limited to the purchase price of the Product and, if Hearth & Home
Technologies is unable to provide replacement or repair in an expedient and cost-effective manner, Hearth & Home
Technologies may discharge all obligations under this warranty by refunding the purchase price of the Product.
EXCEPT TO THE EXTENT PROVIDED BY LAW, HEARTH & Home TECHNOLOGIES MAKES NO EXPRESS
WARRANTIES OTHER THAN THE WARRANTY EXPRESSED HEREIN. THE DURATION OF ANY IMPLIED
WARRANTY IS LIMITED TO THE DURATION OF THE WARRANTY SPECIFIED ABOVE. IN NO EVENT SHALL
HEARTH & Home TECHNOLOGIES BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED
BY DEFECTS IN THE PRODUCT. Some states do not allow limitations on how long an implied warranty lasts, or do not
allow exclusion or limitation of incidental or consequential damages, so these limitations may not apply to you.
To obtain service under this warranty, you must:
1. Send written notice of the claimed condition to: The Technical Services Department, Hearth & Home Technologies
Inc., Mt. Pleasant, 1915 W. Saunders St., Mt. Pleasant, IA 52641 (phone: 1‑800‑927‑6841).
2. Affirm that you are the original owner of the Product.
3. Provide Hearth & Home Technologies reasonable opportunity to investigate the claim, including reasonable
opportunity to inspect the Product prior to any repair or replacement work and before the Product or any component
of the Product has been removed.
4. Obtain Hearth & Home Technologies’ consent to any warranty work before the work is done.
© 2004 Hearth & Home Technologies Inc.
21
803-905 8/04
Quadra-Fire • Fogata Grande