advertisement
www.SenaBluetooth.com
User's Guide
SMH10
© 1998-2013 Sena Technologies, Inc. All rights reserved.
Sena Technologies, Inc. reserves the right to make any changes and improvements to its product without providing prior notice.
Sena™ is a trademark of Sena Technologies, Inc. or its subsidiaries in the USA and other countries. SMH10™, SMH10R™, SMH5™, SMH5-
FM™, SPH10™, SPH10H™, SPH10H-FM™, SPH10S™, SR10™, SM10™ are trademarks of Sena Technologies, Inc. or its subsidiaries. These trademarks may not be used without the express permission of Sena.
The Bluetooth
®
word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sena is under license. iPhone, iPod touch are the registered trademark of Apple Inc. Zumo™ is a trademark of Garmin Ltd. or its subsidiaries. TomTom™ is the trademark or registered trademark owned by TomTom International B.V. Other trademarks and trade names are those of their respective owners.
SMH10
CONTENTS
7. PAIRING WITH SELECTIVE PROFILE: A2DP STEREO OR HANDSFREE .......................... 16
17. THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT .................. 32
1. INTRODUCTION
Thank you for choosing the Sena SMH10, Bluetooth Stereo Headset and Intercom for Motorcycles. With the SMH10, you can call handsfree on your Bluetooth mobile phone, listen to stereo music or voice instructions of GPS navigations by Bluetooth wirelessly, and have intercom conversations in full duplex with a passenger or other motorcycle riders.
The SMH10 is compliant with the Bluetooth 3.0 supporting the following profiles: Headset Profile, Hands-Free Profile (HFP), Advanced Audio
Distribution Profile (A2DP), and Audio Video Remote Control Profile
(AVRCP). Please check with the manufacturers of other devices to determine their compatibility with this headset.
Please read this user’s guide carefully before using the headset. Also check www.SenaBluetooth.com for the latest version of the user’s guide and additional information related to Sena Bluetooth products.
SMH10
The SMH10 features:
• Bluetooth handsfree for Bluetooth mobile phones
• Bluetooth stereo headset for Bluetooth audio devices such as MP3 players
• Bluetooth stereo headset for Bluetooth GPS navigations
• Bluetooth intercom up to 900 meters (980 yards)*
• Four-way conference intercom
• Three-way conference phone call with intercom participant
• Multipoint Bluetooth pairing with GPS navigation or Sena SR10
two-way radio adapter
• Multipoint Bluetooth pairing for 2 mobile phones
• Stereo music by 3.5mm audio cable
• Firmware upgradeable
Key Specifications:
• Bluetooth 3.0
• Supporting profiles: Headset Profile, Hands-Free Profile (HFP),
Advanced Audio Distribution Profile (A2DP), Audio Video Remote
Control Profile (AVRCP)
* in open terrain
5
6
2. PACKAGE CONTENTS
• Headset Main Unit
DC Power Charging & Firmware Upgrade Port
Phone Button
• Answer and end a mobile phone call
• Redial last number
• Call transfer between mobile phone and headset
• Enter into mobile phone pairing mode
• Enter into Bluetooth stereo device paring mode
• Enter into factory reset mode
• Clamp Unit
- Speaker-Microphone Clamp Unit - Basic Kit
(SMH10-10/SMH10D-10)
Speakers
Microphone MP3 Jack
- Speaker-Microphone Clamp Unit with Universal Microphone Kit
(SMH10-11/SMH10D-11)
Jog Dial
• Answer and end a mobile phone call
• Reject an incoming mobile phone call
• Start and end intercom conversation
• Volume adjustment by rotating
• Play and pause Bluetooth stereo device
• Track-forward and track-back by rotating while pressing the button
• Enter into intercom pairing mode
• Enter into voice configuration setting
• Navigate through configuration menu
• Clamp and Speakers
• Boom Microphone
• Wired Microphone
• USB Power & Data Cable
• Cigarette Charger
• 3.5mm Stereo Audio Jack Cable
• Glued Surface Mounting Adapter
• Microphone Sponges
• Speaker Pads
• Velcro Pads for Speakers
• Allen Wrench
SMH10
3. INSTALLING THE SMH10 ON YOUR HELMET
To securely install the SMH10 on the helmet, please follow the procedure.
1. Loosen the two screws on the back plate of the speakermicrophone clamp unit using the enclosed Allen Wrench. Insert the back plate of the clamp unit between the internal padding and external shell of the helmet, and tighten the two screws. Please make sure that the microphone is located properly close to your mouth when you wear the helmet.
Insert
7
8
SMH10
2. Please adjust the direction of the microphone so that the fin side of the microphone is facing outward; away from your lips. You can easily recognize it by touching the fin with your fingers.
fin
In the case of the wired microphone also included in the “Universal
Microphone Kit”, attach the enclosed velcro pad for wired microphone to the inside of the chin guard for full-face helmets.
Place the wired microphone on the velcro pad and connect it to the connector of the clamp unit.
When installing the boom microphone included in the “Universal
Microphone Kit”, place the velcro end of the boom microphone between the internal helmet cheek pad and the internal wall of the helmet shell. The boom microphone should be mounted so it is facing close to your mouth when you wear the helmet. You can use the enclosed velcro pad and holder for the boom microphone to ensure secure placement.
3. Place the helmet speakers along with the velcro pads, centered to your ear, in the ear pockets of the helmet. If the helmet has deep ear pockets, you can use the speaker pads to place the speakers closer to your ears.
4. If you have any problem to clamp the speaker-microphone unit on the helmet for any reason, you may use the glued surface mounting adapter to attach the speaker-microphone clamp unit on the external surface of the helmet.
• Remove the back plate of the speaker-microphone clamp unit by loosening the two screws with the enclosed Allen Wrench.
• Attach the glued external adapter to the speaker-microphone clamp unit by tightening the two screws instead of the removed back plate.
• Locate a proper surface on the helmet to attach the unit, clean the helmet surface location with a moistened towel, and allow to dry thoroughly.
• Peel off the cover of the adhesive tape of the adapter and attach the unit on the proper surface of your helmet.
Attach
SMH10 any responsibility for use of it. Users may have to use the glued adapter at their own risk and responsibility.
5. Attach the headset main unit to the speaker-microphone clamp unit. Insert the bottom part of the main unit completely into the lower slot of the clamp unit first. Then push the upper part of the main unit until it clicks into the upper holder of the clamp unit.
6. To remove the main headset from the speaker-microphone clamp unit, hold the lower part of the speaker-microphone clamp unit with your thumb and gently press down the hook on the upper part of the headset main unit with your index finger until it clicks out.
You may have to do this to charge up or to carry the headset main unit.
Sena recommends the clamp unit over the glued surface mounting adapter. Even though the glued surface mounting adapter is provided for convenience, Sena does not assume
9
SMH10
4. POWERING ON/OFF AND CHARGING
To power on and off the headset, you don’t need to press and hold any button for several seconds. Just short press the Jog Dial and the Phone Button simultaneously, and you will get quick on-and-off convenience.
4.1 Powering On
Press the Jog Dial and the Phone Button at the same time for about
1 second to power on. The blue LED turns on and you will hear ascending beeps.
4.2 Powering Off
Just short press the Jog Dial and the Phone Button simultaneously, you don’t need to press and hold for a few seconds. The red LED turns on for a while until it turns off completely and you will hear descending beeps.
4.3 Charging
The LED turns on red while charging, and turns to blue when the headset is fully charged. It takes about 2.5 hours to be completely charged.
10
4.4 Low Battery Warning
When the battery is low, the blinking blue LED in stand-by mode turns to red and you will hear mid-tone triple beeps and a voice prompt saying “Low battery”.
4.5 Checking the Battery Level
You can check the battery level in two different ways when the headset is powering on.
4.5.1 LED Indicator
When the headset is powering on, the red LED flashes rapidly indicating the battery level.
4 flashes = High, 70~100%
3 flashes = Medium, 30~70%
2 flashes = Low, 0~30%
4.5.2 Voice Prompt Indicator
When you power on the headset, keep pressing the Jog Dial and
Phone Button simultaneously for about 3 seconds until you hear high tone triple beeps. Then you will hear voice prompt indicating the battery level. However, if you release the buttons as soon as the headset turns on, you will not hear the voice prompt of battery level indication.
SMH10
5. VOLUME ADJUSTMENT
You can easily adjust the volume by rotating the Jog Dial. You will hear a beep when the volume reaches maximum or minimum level.
The volume is set and maintained independently at different levels for each audio source even when you turn off and on the headset.
For example, once you set the volume for mobile phone handsfree, it will not change even if you adjust the volume when you hear
Bluetooth MP3 music. So you can always maintain the preferred optimum volume level for each audio source.
6. PAIRING THE SMH10 WITH BLUETOOTH DEVICES
Before using the SMH10 Bluetooth headset with any of Bluetooth devices for the first time, you need to do the pairing operation. It can be paired with Bluetooth mobile phones, Bluetooth stereo devices such as MP3, or motorcycle specific Bluetooth GPS, and with other
Sena Bluetooth headsets. This pairing operation is only required once for each Bluetooth device. The headset will remain paired with the devices and automatically connects to the paired devices again when they are within range. You will hear a high tone single beep and a voice prompt when the headset connects to the paired device automatically: “Phone connected” to a mobile phone, “Media
connected” to a Bluetooth stereo device.
6.1 Mobile Phone Pairing
1. Turn on the SMH10 and press the Phone Button for 5 seconds until the LED flashes red and blue alternately and you hear multiple beeps. You will hear a voice prompt saying “Phone pairing”.
2. Search for Bluetooth devices on your mobile phone. Select the
Sena SMH10 in the list of the devices detected on the mobile phone.
11
SMH10
3. Enter 0000 for the PIN. Some mobile phones may not ask for the
PIN.
4. The mobile phone confirms that pairing has completed and the
SMH10 is ready to use. You will hear a voice prompt from the
SMH10 saying “Your headset is paired”.
5. If the pairing process is not completed within three minutes, the
SMH10 will return to stand-by mode.
6.2 Multipoint Pairing
Typical Bluetooth headsets can connect with only one HFP (Hands-
Free Profile) device, but multipoint pairing allows the headset to connect with two HFP devices at the same time. So, when you already have a mobile phone connected with the SMH10, you can also pair and connect a second mobile phone or other HFP devices such as
GPS or Sena SR10, Bluetooth adapter.
1. To pair the second mobile phone, press the Jog Dial for 5 seconds again until the red LED is rapidly flashing and you hear multiple beeps.
2. Within 2 seconds, tap the Phone Button again, then the LED turns to blue flashing and the beeps turn to high tone double beeps. You will hear a voice prompt saying “Multipoint pairing”.
3. Search for Bluetooth devices on your mobile phone. Select the
Sena SMH10 in the list of the devices detected on the mobile phone.
12
4. Enter 0000 for the PIN. Some mobile phones may not ask for the
PIN.
5. The mobile phone confirms that pairing has completed and the
SMH10 is ready to use. You will hear a voice prompt from the
SMH10 saying “Your headset is paired”.
6. If you want to pair a GPS by multipoint pairing, search for the
Bluetooth device on the GPS screen, and select the Sena SMH10 at step 3. Please refer to the section “6.4.1 Multipoint GPS Pairing” for more details.
7. If you want to pair the Sena SR10, Bluetooth adapter, please refer to the section “6.5 Pairing with the Sena SR10, Bluetooth Two-way
Radio Adapter”.
6.3 Bluetooth Stereo Device Pairing
1. If the Bluetooth stereo device is integrated with the mobile phone such as smartphones, you don’t need to pair the SMH10 with it separately. When the SMH10 is paired with the mobile phone, it is also paired as a stereo music device.
2. If you have a stand alone Bluetooth stereo device, follow the paring procedure separately. The procedure is the same as the procedure in “6.1 Mobile Phone Pairing”.
Note:
1. If Bluetooth connection between the headset and a mobile phone is disconnected, tap the Phone Button to recover the Bluetooth connection immediately.
2. If Bluetooth connection between the headset and a media player is disconnected, press the Jog Dial for 1 second to recover the Bluetooth connection and play.
6.4 Bluetooth GPS Navigation Pairing
You can listen to voice instruction from Bluetooth GPS navigation.
Some GPS systems use mobile phone profile (HFP, Hands-Free
Profile) and others use stereo music profile (A2DP, Advanced
Audio Distribution Profile). Most motorcycle specific GPS systems use mobile phone profile for turn-by-turn voice instruction. You can simultaneously use a mobile phone and a GPS which uses mobile phone profile by one of the following procedures.
6.4.1 Multipoint GPS Pairing
If you use GPS only for turn-by-turn voice instructions, not for Bluetooth stereo music streaming, multipoint pairing is recommended for the
GPS connection. Multipoint Bluetooth pairing allows the SMH10 to connect two HFP devices at the same time: mobile phone and
GPS navigation. Follow the steps below to pair the GPS using the multipoint pairing.
SMH10
1. Turn on the headset and press the Jog Dial for 5 seconds until the red LED is rapidly flashing and you hear multiple beeps.
2. Within 2 seconds, tap the Phone Button again, then the LED turns to blue flashing and the beeps turn to high tone double beeps.
You will hear a voice prompt saying “Multipoint pairing”.
3. Search for Bluetooth devices on the GPS navigation screen.
Select the Sena SMH10 in the list of the devices detected on the
GPS.
4. Enter 0000 for the PIN.
5. The GPS confirms that pairing has completed and the SMH10 is ready to use. You will hear a voice prompt from the SMH10 saying
“Your headset is paired”.
6. If the pairing process is not completed within three minutes, the
SMH10 will return to stand-by mode.
13
SMH10
The pairing diagram for multipoint GPS pairing is shown in the figure below.
Smart Phone
HFP
+
A2DP
Mobile Phone
Pairing
HFP
SMH10
Multipoint
Pairing
Multipoint GPS Pairing
GPS
6.4.2 GPS Pairing as Mobile Phone
If GPS is not only used for turn-by-turn voice instructions but also is your preferred Bluetooth stereo music source, you can pair the GPS to the SMH10 by following the simple procedures in “6.1 Mobile Phone
Pairing”. When you do this, the SMH10 thinks the GPS is a mobile phone. But the SMH10 can directly pair an additional mobile phone.
14
GPS
HFP
+
(A2DP)
Mobile Phone
Pairing
HFP
SMH10
Multipoint
Pairing
Mobile Phone
GPS Pairing as Mobile Phone
Note:
You have to use a motorcycle specific GPS which transmits turn-byturn voice instruction to the headset by Bluetooth. Most automotive GPS systems don’t have this feature.
6.5 Pairing with the Sena SR10, Bluetooth Two-way
Radio Adapter
The Sena SR10 is a Bluetooth two-way radio adapter for group communication, and uses HFP as do most motorcycle specific GPS navigation systems. If you pair the SMH10 with a SR10 by multipoint pairing, the SMH10 is able to have two HFP devices at the same time: mobile phone and Sena SR10.
1. Turn on the headset and press the Jog Dial for 5 seconds until the red LED is rapidly flashing and you hear multiple beeps.
2. Within 2 seconds, tap the Phone Button again, then the LED turns to blue flashing and the beeps turn to high tone double beeps.
You will hear a voice prompt saying “Multipoint pairing”.
3. Turn on the SR10 and follow the SR10’s “Bluetooth Headset
Pairing” procedure to complete the process. Please refer to the
SR10 user's guide for details.
4. When the pairing is completed, you will hear a voice prompt saying “Your headset is paired”.
5. If the pairing process is not completed within three minutes, the
SMH10 will return to stand-by mode.
SMH10
The incoming audio from the two-way radio via SR10 is heard in the background while having an intercom conversation or a mobile phone call. You can listen to music, answer a mobile call, have an intercom conversation and use a two-way radio via SR10 for group communication as shown in the figure below. A GPS navigation or a radar detector could be connected to the SR10 by wire. The GPS voice instruction or the radar detector alarm is also heard in the background via SR10 while having an intercom conversation or a phone call. Please refer to the SR10 user's guide for details.
15
16
SMH10
Smart Phone
HFP
+
A2DP
Mobile Phone
Pairing
Two-way Radio
Wired
Connection
SMH10
HFP
Multipoint
Pairing
Sena SR10
Wired
Connection
Wired
Connection
GPS
Radar Detector
Parallel Connection of SR10 and Mobile Phone by
Bluetooth Multipoint Pairing
7. PAIRING WITH SELECTIVE PROFILE:
A2DP STEREO OR HANDSFREE
If you have a MP3 stereo music phone such as a smartphone, sometimes you may need to selectively use the SMH10 for
A2DP stereo music only or for mobile phone handsfree only. This instruction is for advanced users who want to pair the SMH10 to their smartphones only with one selective profile: A2DP stereo for music or
HFP for phone call.
If you have previously paired a mobile phone to the SMH10, you must clear the previous paring list on both devices; the mobile phone and SMH10. To clear the pairing list on SMH10, please do a factory reset or follow the pairing list clearing procedure described in this manual. To clear the pairing list on the mobile phone, please refer to the mobile phone manual. For most smartphones, delete the Sena
SMH10 from the list of Bluetooth devices in setting menu.
7.1 A2DP Stereo Music Only
1. Turn on the headset and press the Phone Button for 5 seconds until the LED flashes red and blue alternately and you hear multiple beeps.
2. Within 2 seconds, tap the Jog Dial again, then the LED turns to red flashing and the beeps turn to double mid-tone beeps. You will hear a voice prompt saying “Media selective pairing”.
3. Search for Bluetooth devices on your smartphone. Select the
Sena SMH10 in the list of devices detected on your phone.
4. Enter 0000 for the PIN. Some smartphones may not ask for PIN.
7.2 HFP for Phone Call Only
1. Turn on the headset and press the Phone Button for 5 seconds until the LED flashes red and blue alternately and you hear multiple beeps.
2. Within 2 seconds, tap the Phone Button again, then the LED turns to blue flashing and the beeps turn to multiple mid-tone beeps.
You will hear a voice prompt saying “Phone selective pairing”.
3. Search for Bluetooth devices on your smartphone. Select the
Sena SMH10 in the list of devices detected on your phone.
4. Enter 0000 for the PIN. Some smart phones may not ask for PIN.
SMH10
8. INTERCOM PAIRING
8.1 Pairing with Other SMH10 Headsets for Intercom
Conversation
The SMH10 can be paired with up to three other headsets for
Bluetooth intercom conversation.
1. Turn on the two SMH10 headsets (A and B) that you would like to pair with each other.
2. Press and hold the Jog Dial of the headset A and B for 5 seconds until red LEDs of the both units start to flash rapidly. You will hear a voice prompt saying “Intercom pairing”.
3. Simply tap the Jog Dial of any one of the two headsets A or B
(It doesn’t matter that you choose A or B.) and wait until the
LEDs of both headsets turn to blue and intercom connection is automatically established. The two SMH10 headsets A and B are paired with each other for intercom conversation. If the pairing process is not completed within one minute, the SMH10 will return to stand-by mode.
17
SMH10
B
C
A
D
Pairing A & B
4. You can make other pairings between the headset A and C, and between the headset A and D by following the same procedure as above.
A A
B
C
D B
C
D
5. The intercom pairing queue is ‘Last-Come, First-Served’. If a headset has multiple paired headsets for intercom conversations, the last paired headset is set as first intercom friend. The previous intercom friend becomes second intercom friend, and
third intercom friend.
Note:
For example, after the pairing procedures listed above, headset D is the first
intercom friend of headset A. Headset C is the second intercom friend of headset A, and headset B is the third intercom friend of headset A.
8.2 Pairing with Other Sena Headset Models for Intercom
Conversation
The SMH10 can be paired with all other Sena headset models such as the SMH5 and the SPH10 for intercom conversation. Please follow the same procedure as above to pair with these headset models.
Note:
The SMH5 cannot participate in three-way or four-way conference intercom with the SMH10 or the SPH10. The SMH5 has a limited capability of having two-way intercom with each other or with other Sena headsets such as the
SMH10 and the SPH10.
Pairing A & C Pairing A & D
18
9. SMH10 CONFIGURATION SETTING
You can set the configuration of the SMH10 by the voice menu instruction as below.
1. To enter into voice configuration menu, press and hold the Jog
Dial for 12 seconds until the LED shows solid blue and you hear high tone double beeps. You will also hear a voice prompt saying
“Configuration menu”.
2. Rotate the Jog Dial clockwise or counter-clockwise to navigate between the menus. You will hear voice prompts for each menu items as below.
3. You can enable the feature or execute the command by tapping the Phone Button, or disable the feature by tapping the Jog Dial.
4. If any button is not pressed within 10 seconds, the SMH10 will exit the configuration and goes back to stand-by mode.
5. If you want to exit the configuration immediately, rotate the Jog
Dial until you hear a voice prompt saying “Exit configuration”, and tap the Phone Button.
SMH10
The voice prompt for each menu item is as below:
(1) Speed dial
(2) VOX phone
(3) VOX intercom
(4) Voice prompt
(5) Delete all pairings
(6) Exit configuration
Speed dial
Exit configuration
VOX phone
Delete all pairings
VOX intercom
Voice prompt
9.1 Assigning Speed Dial
Voice Prompt
Factory Default
Execute
“Speed dial”
N/A
Tap the Phone Button
1. To assign a phone number as a speed dial, rotate the Jog Dial until you hear a voice prompt saying “Speed dial”.
19
SMH10
2. Tap the Phone Button, and you will hear a voice prompt saying
“Speed dial one” and “Phone connected”.
3. Rotate the Jog Dial to select one of three speed dial numbers and you hear a voice prompt saying “Speed dial (#)”.
4. Call a phone number you want to assign and you will hear a voice prompt saying “Save speed dial (#)”. The phone number is automatically assigned to the selected speed dial number. Then the phone call will hang up before being connected.
5. To exit the menu, rotate the Jog Dial clockwise or counter clockwise until you hear a voice prompt saying “Cancel”, and tap the Phone
Button to confirm. You will then hear a voice prompt saying
“Cancel”. If any button is not pressed within 1 minute, the SMH10 will exit the configuration menu and go back to stand-by mode.
Note:
1. After assigning a phone number to one of three speed dials, you can continually assign another phone number to the rest of two speed dials.
2. You can assign phone numbers to speed dials in your PC. Please visit the Sena Bluetooth web site at www.SenaBluetooth.com for more information.
9.2 Enabling/Disabling Voice Activated Phone Answering
Voice Prompt
Factory Default
Enable
Disable
“VOX phone”
Enable
Tap the Phone Button
Tap the Jog Dial
If this feature is enabled, you can answer incoming calls by simply saying a word loudly enough. For example, when you hear a series of beeps for an incoming call, you can answer the phone by saying
“Hello” or any other word loudly. This is enabled from the factory but you can disable this. If this mode is disabled, you have to tap the Jog
Dial or the Phone Button to answer an incoming call.
9.3 Enabling/Disabling Voice Activated Intercom
Voice Prompt
Factory Default
Enable
Disable
“VOX intercom”
Disable
Tap the Phone Button
Tap the Jog Dial
If this feature is enabled, you can initiate an intercom conversation with the last connected intercom friend by speaking any word loudly enough. The most effortless way to trigger intercom VOX is to blow into
20
the microphone as if blowing dust off the microphone. If you start an intercom conversation by VOX, the intercom terminates automatically when you and your intercom friend remain silent for 20 seconds.
However, if you manually start an intercom conversation by tapping the
Jog Dial, you have to terminate the intercom conversation manually.
However, even when this feature is enabled, if you terminate intercom conversation manually with the Jog Dial, you are not able to start intercom by voice temporarily. In this case, you have to tap the Jog
Dial to restart the intercom. This is to prevent repeated unintentional intercom connections by strong wind noise. If you tap the Jog Dial to start an intercom conversation, it is not terminated by 20 seconds of silence. After turning SMH10 off and on, you can start intercom by voice again.
SMH10
9.4 Enabling/Disabling Voice Prompts
Voice Prompt
Factory Default
Enable
Disable
“Voice prompt”
Enable
Tap the Phone Button
Tap the Jog Dial
You can disable voice prompts by configuration setting, but the following voice prompts are always on.
- Voice prompts for configuration setting menu
- Voice prompts for battery level Indicator
- Voice prompts for factory reset
9.5 Delete all Bluetooth Pairing Information
Voice Prompt
Factory Default
Execute
“Delete all pairings”
N/A
Tap the Phone Button
To delete all Bluetooth pairing information of the SMH10, rotate the
Jog Dial until you hear a voice prompt saying “Delete all pairings”, and tap the Phone Button to confirm. Taping the Jog Dial is not available for this setting.
21
SMH10
9.6 Exit Voice Configuration Menu
Voice Prompt
Factory Default
Enable
“Exit configuration”
N/A
Tap the Phone Button
To exit voice configuration menu and get back to stand-by mode, rotate the Jog Dial until you hear a voice prompt saying
“Exit
configuration”, and tap the Phone Button to confirm. Tapping the
Jog Dial is not available for this setting.
Rotate Jog Dial
Speed Dial
VOX Phone
VOX Intercom
Voice Prompt
Delete All Pairings
Exit Configuration
Tap Phone Button
Execute
Enable
Enable
Enable
Execute
Execute
Voice Configuration Menu & Button Operations
Tap Jog Dial
N/A
Disable
Disable
Disable
N/A
N/A
10. FUNCTION PRIORITY
The SMH10 operates in the following order of priority:
(highest) Mobile phone,
Intercom,
Stereo music by audio cable,
Music sharing by Bluetooth stereo music,
(lowest) Bluetooth stereo music
A lower priority function is always interrupted by a higher priority function. For example, stereo music is interrupted by intercom call, and intercom conversation is interrupted by incoming mobile phone call.
22
11. STEREO MUSIC
You can listen to stereo music in two ways: with the enclosed stereo audio cable or by Bluetooth wireless stereo.
11.1 By Stereo Audio Cable
Plug your stereo MP3 player directly to the SMH10 by using the enclosed 3.5mm stereo audio jack cable. To adjust the volume, rotate the Jog Dial on the headset. You may adjust the volume on the MP3 player also.
SMH10
Remote Control Profile (AVRCP), so if your Bluetooth audio device also supports the AVRCP, you can use the SMH10 to remotely control music playback.
You not only can adjust the volume but also use the functions such as play, pause, next track and previous track.
1. To adjust the volume, rotate the Jog Dial.
MP3 Jack
2. To play or pause music, press and hold the Jog Dial for 1 second until you hear a double beep.
11.2 By Bluetooth Wireless Stereo
The Bluetooth audio device must be paired with the SMH10 by following the “Bluetooth Stereo Device Pairing” procedures described in the 6.3 chapter. The SMH10 supports the Audio/Video
23
SMH10
3. To track forward or track back, rotate while pressing the Jog Dial clockwise or counter clockwise.
Note:
Bluetooth music is available only when the MP3 jack port remains open.
Please make sure the audio cable is unplugged from the clamp unit to play music by Bluetooth.
12. MOBILE PHONE CALL MAKING AND ANSWERING
12.1 Mobile Phone Call Making and Answering
1. When you have an incoming call, simply tap the Phone Button or the Jog Dial to answer the call.
2. You can also answer the incoming call by loudly speaking any word of your choice if Voice Activated Phone Answering is enabled.
3. To end a call, tap the Phone Button or press the Jog Dial for 2 seconds until you hear a beep, or wait for the called person to end the call.
4. To reject a call, press the Jog Dial for 2 seconds until you hear a beep while the phone is ringing.
5. To transfer a call between the mobile phone and the headset during the phone conversation, press the Phone Button for 2 seconds until you hear a beep.
6. There are several ways to make a phone call:
• Enter numbers on your mobile phone keypad and make a call.
Then the call is automatically transferred to the headset.
• For some older mobile phones which do not automatically transfer calls to the headset, press the Phone Button after entering phone numbers on the mobile phone keypad.
24
• Tap the Phone Button in stand-by mode to activate the voice dialing of your mobile phone. For this, the voice dialing feature must be available on the mobile phone. Refer to your mobile phone manual for further instruction.
Note:
1. If you are using multipoint mobile phone connection and you have an incoming call from the second phone during the call of the first phone, then you may still receive the call from second phone. In this case, the call from the first phone is on waiting mode. If you end a call, then it will automatically guide you to the first phone call.
2. If you are using multipoint connection of mobile phone and GPS, you may not be able to listen to the GPS voice instruction during the phone call.
12.2 Speed Dialing
You can quickly make a phone call by using the voice speed dial menu.
1. To enter into the voice speed dial menu, double tap the Phone
Button and you will hear a mid-tone single beep and a voice prompt saying “Speed dial”.
2. Rotate the Jog Dial clockwise or counter-clockwise to navigate between the menus. You will hear voice prompts for each menu items.
SMH10
3. Tap the Phone Button or the Jog Dial to select a voice menu among the followings:
(1) Last number redial
(2) Speed dial 1
(3) Speed dial 2
(4) Speed dial 3
(5) Cancel
4. After selecting the last number redial menu, you will hear a voice prompt saying “Last number redial”. Then, to redial the last phone call number, tap the Phone Button or the Jog Dial.
5. To call one of the speed dials, rotate the Jog Dial clockwise or counter-clockwise to navigate between the menus until you hear a voice prompt saying “Speed dial (#)”. Then, tap the Phone Button or the Jog Dial.
6. If you want to exit the speed dial immediately, rotate the Jog
Dial until you hear a voice prompt saying “Cancel”, and tap the
Phone Button or the Jog Dial. If any button is not pressed within 15 seconds, the SMH10 will exit the voice speed dial menu and goes back to stand-by mode.
Note:
Make sure that you should connect the mobile phone and the headset in order to use the speed dial function.
25
26
SMH10
Answer
End
Reject
Tap Phone Button or Tap Jog Dial or Say
“Hello”
Tap Phone Button or Press Jog Dial for 2”
Press Jog Dial for 2”
Transfer
Call
Press Phone Button for 2”
Use phone keypad
Speed Dial Double tap Phone Button
Voice Command Tap Phone Button
Mobile Phone Call Button Operations
13. TWO-WAY INTERCOM
13.1 Start and End Two-way Intercom
1. You can start an intercom conversation with one of any intercom friends by tapping the Jog Dial: single tapping to intercom with the first intercom friend, double tapping with the second intercom friend, and triple tapping with the third intercom friend.
1 st Intercom
Friend
2 nd Intercom
Friend
3 rd Intercom
Friend
Start Two-way Intercom Conversation
2. To terminate an intercom conversation, single tap the Jog Dial. Any intercom connection with any intercom friend will be terminated by a single tapping. A double or triple tapping will do nothing in this case.
Terminate
End Two-way Intercom Conversation
Start intercom
End intercom
1st intercom friend
Single tap
2nd intercom friend
Double tap
Single tap
3rd intercom friend
Triple tap
13.2 Intercom and Mobile Phone Call
1. When you have an incoming mobile phone call during an intercom conversation, you will hear a ring tone. You can choose whether to 1) answer the mobile phone call and stop the intercom conversation, or 2) reject the phone call and stay on the intercom conversation.
SMH10 a. To answer the phone call and stop the intercom conversation, tap the Jog Dial or the Phone Button. When you hang up the phone call, the intercom will automatically be recovered.
b. To reject the phone call and stay on the intercom conversation, press the Jog Dial for 2 seconds until you hear a beep.
Unlike other motorcycle Bluetooth headsets, this prevents a user from being dropped out of an intercom conversation by an incoming mobile call.
2. When you have an incoming intercom call during a mobile phone call, you will hear 4 high tone beeps, alerting you that there is an incoming intercom call. You will also hear a voice prompt saying
“Intercom requested”. In this case, the intercom call does not override the mobile phone call because intercom has lower priority than mobile call. You have to hang up the mobile phone call to make or receive an intercom call.
13.3 Intercom and GPS
If you pair a Bluetooth GPS to the SMH10 as described in 6.4 of this user's guide, you can hear the turn-by-turn voice instruction of the GPS while having an intercom conversation. The GPS voice instruction interrupts intercom conversation, but it is automatically reestablished after the GPS voice instruction ends.
27
SMH10
GPS
Voice
Instruction
Multipoint
Pairing
HFP Intercom
Smart Phone
Mobile Phone
Pairing
SMH10
Intercom
Pairing
Intercom Friend
Intercom and GPS voice instruction
13.4 Intercom and Two-way Radio
As described in 6.5 of this user's guide, you can use a two-way radio and SMH10 Bluetooth intercom simultaneously by using the Sena
SR10, a Bluetooth Two-way Radio Adapter, along with the SMH10.
Incoming audio from the two-way radio is not interrupting an intercom conversation but is heard in background. This is useful when you have an intercom conversation with a passenger on the back seat and use a two-way radio for group communication with other motorcycle riders.
28
Smart Phone
HFP
+
A2DP
Mobile Phone
Pairing
Two-way Radio
Wired
Connection
SMH10
Audio from
Two-way Radio
Sena SR10
Wired
Connection
Multipoint
Pairing
Wired
Connection
Intercom
Intercom
Pairing
GPS
Radar Detector
Intercom Friend
Intercom and Two-way Radio
14. THREE-WAY CONFERENCE INTERCOM
14.1 Start Three-way Intercom
You (A) can have a three-way conference intercom with two other
SMH10 friends (B & C) by establishing two intercom connections at the same time. While a three-way conference intercom is in progress, mobile phone connection of all three participants would be temporarily disconnected, but as soon as the conference intercom terminates or one of the participants leaves the intercom, all mobile phones would be automatically reconnected. During the conference intercom, if you have an incoming mobile phone call, terminate the conference intercom to automatically reconnect the mobile phone and receive the call.
SMH10
1. You (A) need to be paired with two other friends (B & C) for threeway conference intercom.
Pairing
(A)
Pairing
First Friend
(B)
Second Friend
(C)
2. Start an intercom conversation with one of the two friends in your intercom group. For example, you (A) may start an intercom conversation with the intercom friend (B). Or intercom friend (B) may start an intercom call with you (A).
(A)
First Friend
(B)
Second Friend
(C)
29
SMH10
3. The second intercom friend (C) may join the intercom by making an intercom call to you (A).
First Friend
(B)
Second Friend
(C)
4. Now you (A) and two SMH10 intercom friends (B & C) are having a three-way conference intercom.
First Friend
(B)
(A)
(A)
Second Friend
(C)
14.2 End Three-way Intercom
When you are a member of an active three-way conference intercom, you can completely terminate the conference intercom or just disconnect an intercom connection with one of your active intercom friends.
1. Press the Jog Dial for 1 second until you hear a beep to terminate three-way conference intercom completely. It terminates both intercom connections with (B) and (C).
2. Tap or double tap the Jog Dial to disconnect intercom connection with one of the two intercom friends accordingly. For example, by single tapping the Jog Dial, you can just terminate the intercom connection with the first intercom friend (B). However, you still have the intercom connection with your second intercom friend (C).
Jog Dial Operation
Press for 1”
Single tap
Double tap
End Three-way Intercom
Result
Disconnect (B) & (C)
Disconnect (B)
Disconnect (C)
30
15. FOUR WAY CONFERENCE INTERCOM
15.1 Start Four-way Intercom
You can have four-way conference intercom with three other SMH10 users by adding one more intercom participant to the three-way intercom. While you are having three-way intercom as above in section 14.1, a new participant (D), who is an intercom friend of your intercom friend (C), may join the conference intercom by making an intercom call to your intercom friend (C). Please note that in this case, the new participant (D) is an intercom friend of (C), not of you
(A).
First Friend
(B)
You
(A)
Second Friend
(C)
New Participant
(D)
= Intercom Friend of (C)
SMH10
15.2 End Four-way Intercom
As same in the case of three-way intercom, you can completely get out of the four-way conference intercom or just disconnect a single intercom connection.
1. Press the Jog Dial for 1 second until you hear a beep to terminate four-way conference intercom. It terminates the intercom connections between you (A), and your intercom friends (B), (C) and (D).
2. Tap or double tap the Jog Dial to disconnect the intercom connection with one of the two intercom friends accordingly.
However, when you disconnect the second friend (C) by double tapping the Jog Dial, you will be disconnected with the third participant (D) as well. This is because the third participant (D) is connected with you via the second friend (C).
Jog Dial Operation
Press for 1”
Single tap
Double tap
Result
Disconnect (B), (C) & (D)
Disconnect (B)
Disconnect (C) & (D)
End Four-way Intercom
31
SMH10
16. MUSIC SHARING
You can start sharing music with an intercom friend using Bluetooth stereo music during a two-way intercom conversation. When you terminate music sharing, you can go back to the intercom conversation.
To start or terminate sharing music, press and hold the Jog Dial for 1 second during an intercom conversation until you hear a double beep and you and your intercom friend will listen to or terminate sharing music. To track forward or track back, rotate while pressing down the
Jog Dial clockwise or counter clockwise.
Note:
1. Both you and your intercom friend can remotely control music playback during music sharing such as track forward and track back.
2. When you have an incoming call, make a phone call, or hear the turnby-turn voice instruction of GPS during music sharing, the function will be paused.
3. In order to share music, make sure that you update both headsets with the firmware that has the music sharing feature, and enable the EDR setting in the Sena Device Manager.
17. THREE-WAY CONFERENCE PHONE CALL
WITH INTERCOM PARTICIPANT
You can have a three-way conference phone call by adding an intercom friend to the mobile phone conversation. While having a mobile phone call, make an intercom call to one of the intercom friends by tapping the Jog Dial to form a three-way conference call with the person on the mobile phone line. To disconnect the intercom first and go back to your private mobile phone call, terminate the intercom by tapping the Jog Dial. To end the mobile phone call first and maintain the intercom conversation, press the Jog Dial for 2 seconds, or tap the phone button, or wait for the person on the mobile phone line to end the call.
Start
End intercom first
End phone call first
Tap Jog Dial while having a mobile phone call
Tap Jog Dial
Press Jog Dial for 2”
or
Tap Phone Button
or
Wait for the called person to end the call
Start & End Three-way Conference Phone Call
32
18. INTERCOM FAILURE
When you try to start an intercom conversation with an intercom friend who is already having a conference intercom with other riders or a mobile phone call, you will hear a low tone double beep signifying an intercom busy signal. In this case, you have to try again later.
19. INTERCOM RECONNECTION
If your intercom friend goes out of range while having an intercom conversation, you may hear static noise and eventually the intercom will be disconnected. In this case, the SMH10 automatically tries to reconnect the intercom every 8 seconds and you will hear high tone double beeps until the intercom is reestablished. If you don’t want to make a reconnection, tap the Jog Dial to stop the attempt.
SMH10
20. RESET TO FACTORY DEFAULT SETTINGS
1. To restore the SMH10 to factory default settings, press and hold the Phone Button for 12 seconds until the LED shows solid red and you hear double beeps. You will hear a voice prompt saying
“Factory reset”.
2. Within 5 seconds, press the Jog Dial to confirm reset. The headset will be restored to factory setting and switched off automatically.
You will hear a voice prompt saying “Headset reset, good-bye”.
3. If you don’t press the Jog Dial within 5 seconds, the reset attempt is canceled and the headset returns to stand-by mode. You will hear a voice prompt saying “Canceled”.
33
SMH10
21. FAULT RESET
When the SMH10 is not working properly or is in faulty status for any reason, you may reset by pushing the pin-hole reset button at the back of the headset main unit. Insert a paper clip into the reset pinhole and press the reset button for a second with light pressure. The
SMH10 will be switched off, and you have to turn the system back on and try again. However, this will not restore the headset to factory default settings.
22. FIRMWARE UPGRADE
The SMH10 supports firmware upgrade function. Please visit Sena
Bluetooth web site at www.SenaBluetooth.com to check the latest software downloads.
34
23. SENA BLUETOOTH CONNECTION
CASE STUDIES
Case 1
Intercom
Pairing
Mobile Phone
Mobile Phone
Pairing
Multipoint
Pairing
Bluetooth GPS*
Bluetooth Pairing Procedure
1. Mobile Phone Pairing
2. Multipoint Pairing
3. Intercom Pairing
Bluetooth GPS*
zumo 220/350/550/660/665, TomTom Rider
Usage
• Mobile phone: phone call, listening to music
• GPS: GPS instruction
• Intercom
SMH10
35
Case 2
SMH10
GPS - Mobile
Phone Pairing
Bluetooth GPS*
Mobile Phone
Pairing
Mobile Phone
Intercom
Pairing
Bluetooth Pairing Procedure
1. GPS - Mobile Phone Pairing
2. Mobile Phone Pairing
3. Intercom Pairing
Bluetooth GPS*
zumo 550/660/665, TomTom Rider
Usage
• GPS
zumo 660/665: GPS instruction, phone call, listening to music
zumo 550, TomTom Rider: GPS instruction, phone call
• Intercom
36
Case 3
Bluetooth GPS*
Mobile Phone
Pairing
Intercom
Pairing
Multipoint
Pairing
Mobile Phone
Bluetooth Pairing Procedure
1. Mobile Phone Pairing
2. Multipoint Pairing
3. Intercom Pairing
Bluetooth GPS*
zumo 220/350/550/660/665, TomTom Rider
Usage
• Mobile Phone: phone call
• GPS
zumo 660/665: GPS instruction, listening to music
zumo 220/350/550, TomTom Rider: GPS instruction
• Intercom
Case 4
Intercom
Pairing
Bluetooth Pairing Procedure
1. Mobile Phone Pairing
2. Mobile Phone Pairing
3. Intercom Pairing
Bluetooth GPS*
Yupiteru, smartphone apps
Usage
• Mobile Phone: phone call
• GPS: GPS instruction
• Intercom
Mobile Phone
Mobile Phone
Pairing
Mobile Phone
Pairing
Bluetooth GPS*
SMH10
Case 5
Mobile Phone
Mobile Phone
Pairing
GPS
Intercom
Pairing
Mobile Phone
Pairing
Motorcycle Bluetooth
Audio System*
Music
Bluetooth Pairing Procedure
1. Mobile Phone Pairing
2. Mobile Phone Pairing
3. Intercom Pairing
Motorcycle Bluetooth Audio System*
BMW R1200RT, K1600GT, K1600GTL
Usage
• Mobile Phone: phone call
• Motorcycle Bluetooth Audio System: listening to music, GPS instruction
• Intercom
37
Case 6
SMH10
Intercom
Pairing
Mobile Phone
Mobile Phone
Pairing
Mobile Phone
Pairing
Motorcycle Bluetooth
Audio System*
Multipoint
Pairing
Music
Bluetooth Pairing Procedure
1. Mobile Phone Pairing
2. Mobile Phone Pairing
3. Multipoint Pairing
4. Intercom Pairing
Bluetooth GPS*
zumo 220/350/550/660/665, TomTom Rider
Motorcycle Bluetooth Audio System*
BMW R1200RT, K1600GT, K1600GTL
Usage
• Mobile Phone: phone call
• Motorcycle Bluetooth Audio System: listening to music
• GPS: GPS instruction
• Intercom
Bluetooth GPS*
38
Case 7
Mobile Phone
Mobile Phone
Pairing
Multipoint
Pairing
SR10
Intercom
Pairing
GPS
Two-way Radio
Radar Detector
SMH10
Bluetooth Pairing Procedure
1. Mobile Phone Pairing
2. Multipoint Pairing
3. Intercom Pairing
Usage
• Mobile Phone: phone call
• SR10: two-way radio, GPS guidance, Radar detecting signal
• Intercom
39
SMH10
Case 8
Mobile
Phone
GPS -
Mobile Phone
Pairing
Bluetooth GPS*
Mobile Phone
Pairing
Mobile Phone
Pairing
MP3 Player
Intercom
Pairing
Bluetooth Pairing Procedure
1. GPS - Mobile Phone Pairing
2. Mobile Phone Pairing
3. Mobile Phone Pairing
4. Intercom Pairing
Bluetooth GPS*
zumo 220/350/550/660/665, TomTom Rider
Usage
• GPS: phone call, GPS instruction
• MP3 Player: listening to music
• Intercom
40
Case 9
GPS
Two-way Radio
Radar Detector
SR10
Multipoint
Pairing
Mobile Phone
Mobile Phone
Pairing
Mobile Phone
Pairing
SM10
Intercom
Pairing
Mobile Phone
Pairing
SMH10
Bluetooth Pairing Procedure
1. Mobile Phone Pairing
2. Mobile Phone Pairing
3. Mobile Phone Pairing
4. Multipoint Pairing
5. Intercom Pairing
Usage
• Mobile Phone: phone call
• SR10: two-way radio, GPS instruction, Radar detecting signal
• SM10: listening to music/sharing
• Intercom
41
Case 10
SMH10
Mobile Phone
Mobile Phone
Pairing
42
Intercom
Pairing
Mobile Phone
Pairing
SM10
Multipoint
Pairing
Bluetooth GPS*
Mobile Phone
Pairing
Motorcycle
Audio System
OR
MP3 Player
Bluetooth Pairing Procedure
1. Mobile Phone Pairing
2. Mobile Phone Pairing
3. Mobile Phone Pairing
4. Multipoint Pairing
5. Intercom Pairing
Bluetooth GPS*
zumo 220/350/550/660/665, TomTom Rider
Usage
• Mobile Phone: phone call
• GPS: GPS instruction
• SM10: listening to music/sharing
• Intercom
SMH10
24. OPERATION QUICK REFERENCE
Button
Phone Button
+ Jog Dial
Phone Button
Description
Power-on
Power-off
Mobile phone pairing
MP3, GPS pairing
Call transfer
Factory reset
Make & answer phone call
Speed dial
Duration
1 sec
Tapping
LED
Solid blue
Solid red
Beep
Ascending beeps
Descending beeps
5 sec
5 sec
Blue & red alternatively flashing
Blue & red alternatively flashing
High tone multiple beeps
High tone multiple beeps
Tapping -
12 sec Solid red
Jog Dial within 5 sec to confirm reset
High tone single beep
High tone double beeps
Tapping
Double tapping -
-
-
Button
Jog Dial
Description
Intercom pairing
Multipoint pairing
Duration
5 sec
LED
Red flashing
Beep
Double tone beeps
Jog Dial of any one of the two headsets
5 sec Red flashing Multiple beeps
Phone Button within 2 sec
Start/end intercom conversation
End conference intercom
Reject incoming call
Volume adjustment
Track forward/ back
Play/pause
Bluetooth music
Tapping
1 sec
2 sec
Rotating
Rotating while pressing
1 sec -
-
-
-
-
Blue flashing
-
-
-
-
Mid-tone single beep
Mid-tone double beeps
43
SMH10
BATTERY INFORMATION
The product has an internal, non-removable, rechargeable battery.
Do not attempt to remove the battery from the device as you may damage the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Recharge the battery only with Sena approved chargers designated for this device.
Use of an unapproved charger may present a risk of fire, explosion, leakage, or other hazard.
Always try to keep the battery between 15℃ and 25℃ (59℉ and
77℉). Extreme temperatures reduce the capacity and lifetime of the battery. A device with a hot or cold battery may not work temporarily.
Battery performance is particularly limited in temperatures well below freezing.
Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Never use any charger that is damaged.
Operating times are estimates only and depend on the devices used together, features used, battery age and condition, temperatures to which battery is exposed, and many other factors.
MAINTENANCE AND CARE
The SMH10 should be treated with care and the following suggestions will help you protect your warranty coverage.
1. Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.
2. Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and wrap or melt certain plastics.
3. Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.
4. Do not attempt to open the product.
5. Do not drop or knock the device. Rough handling can break internal circuit boards and fine mechanics.
6. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
7. Do not paint the device. Paint can clog the moving parts and prevent proper operation.
These suggestions apply equally to the headset main unit, speakermicrophone clamp unit, or power charger.
44
DISPOSAL
The crossed-out wheel bin symbol on the product, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European
Union and other locations where separate collection systems are available. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please do not dispose of these products as unsorted municipal waste, but hand it in at an official collection point for recycling.
SMH10
CERTIFICATION AND SAFETY APPROVALS
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
45
SMH10
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.
CE Declaration of Conformity
This product is CE marked according to the provisions of the R&TTE
Directive (99/5/EC). Hereby, Sena declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For further information please consult www.SenaBluetooth.com.
Please note that this product uses radio frequency bands not harmonized within EU. Within the EU this product is intended to be used in Austria, Belgium, Denmark, Finland, France, Germany,
Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal,
Spain, Sweden, United Kingdom and within EFTA in Iceland, Norway and Switzerland.
Industry Canada Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Bluetooth License
The Bluetooth
®
word mark and logos are owned by the Bluetooth
SIG, Inc. and any use of such marks by Sena is under license. Other trademarks and trade names are those of their respective owners
The SMH10 is compliant with and adopts the Bluetooth
®
Specification
3.0 and has successfully passed all interoperability tests that are specified in the Bluetooth
®
®
-enabled products is not guaranteed.
specification. However, interoperability between the device and other Bluetooth
46
WAIVER AND GENERAL RELEASE
By using the product you waive all substantial legal rights including the right to sue. Please read the following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue.
Using a communication device while riding a motorcycle, scooter, moped, ATV, quad-bike or any other vehicle or equipment, whether on land, water or air (jointly referred to as “Vehicle”) requires your complete and undivided attention. Sena Technologies, Inc., including its Officers, Directors, Affiliates, Parent Company, Representatives,
Agents, Contractors, Sponsors, Employees, Suppliers and Resellers
(jointly referred to as the “Company” or “Sena”) strongly advise you to take all necessary precautions and remain alert to the traffic, weather and road conditions if you choose to use the product headset, including all derivative models irrespective of its commercial name or branding (the “Device”), and stop your Vehicle on the roadside prior to initiating or receiving calls. Any publications, advertisements, announcements or similar notes that refer to using the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in traffic.
SMH10
By way of purchasing this Device and not returning it for a full refund
(see below), you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorney’s fees) and holding Sena harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction. Sena will not be responsible for any physical damages, irrespective of reasons, conditions or circumstances, including malfunctioning of the Device, and all risks associated with operating it rest solely and entirely with the user of this Device, irrespective of whether the Device is used by the original purchaser or any third party.
Sena hereby notifies you that using this Device may also be in contravention to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility.
1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and forever release, discharge, indemnify and hold harmless Sena from any and all litigation, claims, debts, demands, actions and liability which may arise, directly or indirectly, from using the Device for any distress, pain, suffering, discomfort, loss, injury, death, damages to or in respect to any
47
SMH10 person or property however caused, WHETHER ARISING FROM
THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said use, to the fullest extent permitted by law.
2. You fully understand and assume the risks in using the Device, including risk of negligent acts or omissions by others.
3. You confirm that you are physically capable to use the Device and that you have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner. You confirm that you are at least eighteen (18) years of age and that you have been advised of the risks associated with the use of the Device. You further confirm that you will not consume any alcohol that may affect your alertness or any mind-altering substance, and will not carry, use or consume these substances before or during the use of the Device.
4. You fully acknowledge our warnings and understand that: (a) risks and dangers exist in using the Device while in traffic, including but not limited to injury or illness, strains, fractures, partial and/ or total paralysis, death or other ailments that could cause serious disability; (b) these risks and dangers may be caused by the negligence of the manufacturers or its agents or any third party involved in designing or manufacturing the Device; (c) these risks and dangers may arise from foreseeable or unforeseeable causes.
You hereby assume all risks and dangers and all responsibility for
48 any losses and/or damages, whether caused in whole or in part by the negligence or other conduct of others, including the Company.
5. You confirm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund (see refund option below).
Two-Year Limited Warranty
Sena Technologies, Inc. (“Sena”) warrants that this product (“Product”) shall conform to and perform in accordance with published technical specifications and the accompanying written materials, and shall be free of defects in materials and workmanship, for a period of two (2) year from the date of purchase by the first consumer purchaser of the
Product. The limited warranty extends only to the original consumer purchaser of the Product and is not assignable or transferable to any subsequent purchaser/end-user.
This warranty is limited to the repair and/or replacement, at Sena’s discretion, of defective or non-conforming Product, and Sena shall not be responsible for the failure of the Product to perform specified functions, or any other non- conformance caused by or attributable to: (a) any misapplication or misuse of the Product; (b) failure of
Customer to adhere to any of Sena’s specifications or instructions; (c) neglect of, abuse of, or accident to, the Product; or (d) any associated
or complementary equipment or software not furnished by Sena.
Limited warranty service may be obtained by delivering the Product to Sena or to the international distributor it was purchased through and providing proof of purchase or receipt date. Customer agrees to insure the Product or assume the risk of loss or damage in transit, to prepay shipping charges to Sena, and to use the original shipping container or equivalent.
Limitation of Liability
EXCEPT AS EXPRESSLY PROVIDED HEREIN, SENA MAKES NO
WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED, WITH
RESPECT TO ANY EQUIPMENT, PARTS OR SERVICES PROVIDED
PURSUANT TO THIS AGREEMENT, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. NEITHER SENA NOR
ITS DEALER SHALL BE LIABLE FOR ANY OTHER DAMAGES,
INCLUDING BUT NOT LIMITED TO DIRECT, INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER IN AN
ACTION IN CONTRACT OR TORT (INCLUDING NEGLIGENCE
AND STRICT LIABILITY), SUCH AS, BUT NOT LIMITED TO, LOSS
OF ANTICIPATED PROFITS OR BENEFITS RESULTING FROM,
OR ARISING OUT OF, OR IN CONNECTION WITH THE USE OF
FURNISHING OF EQUIPMENT, PARTS OR SERVICES HEREUNDER
SMH10
OR THE PERFORMANCE, USE OR INABILITY TO USE THE SAME,
EVEN IF SENA OR ITS DEALER HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL SENA OR
ITS DEALERS TOTAL LIABILITY EXCEED THE PRICE PAID FOR THE
PRODUCT.
Return for Full Refund
IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE
CONDITIONS, YOU MAY RETURN THIS DEVICE TO SENA FOR A
FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 14
BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE
AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING
SO, PLEASE REFER TO THIS SECTION. BY NOT RETURNING THE
DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED, YOU ARE
EXPLICITLY IN AGREEMENT WITH THE ABOVE AND RENOUNCE
ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST SENA
AS DEFINED ABOVE.
49
SMH10
WARNING
Sena informs that using this device in public traffic may not be authorized by the law. Please check your local law and use this device only out of public traffic such as private properties or closed circuits. If the simultaneous use of both ear speakers while riding a motorcycle is prohibited by your local law, please use only a single ear speaker while riding. Sena denies any liability should you choose not to respect this warning.
Using the headset with loud volume may be harmful to your eardrums and cause hearing loss. Please maintain proper volume level to protect your ears.
50
3.2.0
www.SenaBluetooth.com
User's Guide for Firmware v4.3
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 1. INTRODUCTION
- 5 2. PACKAGE CONTENTS
- 6 3. INSTALLING THE SMH10 ON YOUR HELMET
- 9 4. POWERING ON/OFF AND CHARGING
- 9 4.1 Powering On
- 9 4.2 Powering Off
- 9 4.3 Charging
- 9 4.4 Low Battery Warning
- 9 4.5 Checking the Battery Level
- 10 5. VOLUME ADJUSTMENT
- 10 6. PAIRING THE SMH10 WITH BLUETOOTH DEVICES
- 10 6.1 Mobile Phone Pairing
- 11 6.2 Multipoint Pairing
- 11 6.3 Bluetooth Stereo Device Pairing
- 12 6.4 Bluetooth GPS Navigation Pairing
- 14 6.5 Pairing with the Sena SR10, Bluetooth Two-way Radio Adapter
- 15 7. PAIRING WITH SELECTIVE PROFILE: A2DP STEREO OR HANDSFREE
- 15 7.1 A2DP Stereo Music Only
- 16 7.2 HFP for Phone Call Only
- 16 8. INTERCOM PAIRING
- 16 8.1 Pairing with Other SMH10 Headsets for Intercom Conversation
- 17 8.2 Pairing with Other Sena Headset Models for Intercom Conversation
- 18 9. SMH10 CONFIGURATION SETTING
- 18 9.1 Assigning Speed Dial
- 19 9.2 Enabling/Disabling Voice Activated Phone Answering
- 19 9.3 Enabling/Disabling Voice Activated Intercom
- 20 9.4 Enabling/Disabling Voice Prompts
- 20 9.5 Delete all Bluetooth Pairing Information
- 21 9.6 Exit Voice Configuration Menu
- 21 10. FUNCTION PRIORITY
- 22 11. STEREO MUSIC
- 22 11.1 By Stereo Audio Cable
- 22 11.2 By Bluetooth Wireless Stereo
- 23 12. MOBILE PHONE CALL MAKING AND ANSWERING
- 23 12.1 Mobile Phone Call Making and Answering
- 24 12.2 Speed Dialing
- 25 13. TWO-WAY INTERCOM
- 25 13.1 Start and End Two-way Intercom
- 26 13.2 Intercom and Mobile Phone Call
- 26 13.3 Intercom and GPS
- 27 13.4 Intercom and Two-way Radio
- 28 14. THREE-WAY CONFERENCE INTERCOM
- 28 14.1 Start Three-way Intercom
- 29 14.2 End Three-way Intercom
- 30 15. FOUR WAY CONFERENCE INTERCOM
- 30 15.1 Start Four-way Intercom
- 30 15.2 End Four-way Intercom
- 31 16. MUSIC SHARING
- 31 17. THREE-WAY CONFERENCE PHONE CALL WITH INTERCOM PARTICIPANT
- 32 18. INTERCOM FAILURE
- 32 19. INTERCOM RECONNECTION
- 32 20. RESET TO FACTORY DEFAULT SETTINGS
- 33 21. FAULT RESET
- 33 22. FIRMWARE UPGRADE
- 34 23. SENA BLUETOOTH CONNECTION CASE STUDIES
- 42 24. OPERATION QUICK REFERENCE
- 43 BATTERY INFORMATION
- 43 MAINTENANCE AND CARE
- 44 DISPOSAL
- 44 CERTIFICATION AND SAFETY APPROVALS
- 45 • FCC RF Exposure Statement
- 45 • FCC Caution
- 45 • CE Declaration of Conformity
- 45 • Industry Canada Statement
- 45 • Bluetooth License
- 46 WAIVER AND GENERAL RELEASE
- 47 • Two-Year Limited Warranty
- 48 • Limitation of Liability
- 48 • Return for Full Refund
- 49 WARNING