DELUXE ELECTRIC

POWER BRUSH

MODEL: 30635615

!

FOR HOUSEHOLD USE ONLY

!

AB0008

HOMEOWNERS OPERATING INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Venmar Ventilation ULC, Drummondville, Québec 1-844-670-2334

Register your product online at: www.venmar.ca

30042511A

The instructions given in this booklet serve as a guide to routine maintenance. To obtain the most satisfying years of service, read through these instructions and keep them handy for future reference.

IMPORTANT SAFETY INSTRUCTIONS

When using an electric appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THE POWER BRUSH.

WARNING

!

To reduce the risk of fire, electric shock or injury:

1. Always turn power off and unplug before cleaning or servicing the power brush.

2. Do not pick up the following items: Sharp objects, flammable liquids, hot ashes, burning matches, cigarettes, etc.

3. Never use, connect or disconnect the power brush with wet hands.

4. Do not use with damaged power plug or plug pins. If the power brush is not working properly, contact your local supplier or service agent. The problem may be covered under the warranty.

5. Do not put objects into the brush opening.

6. Do not use with brush opening or air channel blocked. Keep free of dust, hair, etc.

7. Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

8. Never leave electric power brush unattended while it is plugged in.

9. This is not a toy. Do not let children play with power brush. Children should be supervised when near the power brush.

10. Use only manufacturer’s recommended attachments.

11. Do not use outdoors or on wet surfaces.

12. Do not use to pick up water.

13. Use extra care when cleaning stairs.

14. Always check underside of product for any obstructions prior to use.

15. Do not use without dust bag (with 500VF model) or permanent filter (with 600 VF and 650VF models) in place in power unit.

16. Motor shaft can become hot during normal use. To prevent burns, avoid touching the motor shaft when servicing the drive belt.

17. Keep your work area well lighted.

18. When servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.

19. Store your cleaner indoor in a clean, dry area.

- 2 -

1. HOW TO ASSEMBLE POWER BRUSH/WAND/HANDLE

 Read important safety instructions before installing power brush.

 Ensure hose is disconnected from power supply before installing power brush.

 Push wand into power brush neck so that the lock button snaps in place.

 Connect hose handle into wand quick connector and ensure that the prongs are aligned with the receptacle holes. Push until lock button snaps in place.

H

OSE

H

ANDLE

L

OCK

B

UTTON

R

ECEPTACLE

W

AND TO

P

OWER

B

RUSH

C

ONNECTION

P

RONGS

L

OCK

B

UTTON

Q

UICK

C

ONNECTOR

P

OWER

B

RUSH

N

ECK

H

EIGHT

A

DJUSTMENT

P

EDAL

W

AND

R

ELEASE

P

EDAL

P

OWER

B

RUSH

N

ECK

R

ELEASE

P

EDAL

W

AND

W

AND

G

RIP

AO0078

H

OSE

H

ANDLE TO

W

AND

C

ONNECTION

H

OSE

H

ANDLE

L

OCK

B

UTTON

R

ECEPTACLE

P

RONGS

L

OCK

B

UTTON

P

OWER

B

RUSH

H

OSE

H

ANDLE

R

ELEASE

B

UTTON

W

AND

AO0021

AO0019

W

AND

& H

OSE

C

OMPATIBILITY

See Section 5 on page 7 for wand and hose compatibility table.

?

AD0028

- 3 -

2. HOW TO USE POWER BRUSH/WAND

CAUTION

Always pick up hard or sharp objects by hand before using your power brush. Items such as pins, hairpins, tacks, crayons, etc., may damage the brush roll or may break the belt.

2.1 WAND RELEASE

The power brush is not recommended for use on bare floors. Wand release pedal (A) on power brush allows you to quickly disconnect wand and switch to combination floor/rug tool for use on bare floors.

2.2 POWER BRUSH NECK RELEASE

CAUTION

Always unlock brush neck before use.

C

B

A

Push down power brush neck release pedal (B) to unlock brush neck. Return the neck to the upright position for storage.

AO0020

2.3 POWER BRUSH HEIGHT ADJUSTMENT

The icons (D) refer to the carpet pile height. Select height by depressing height adjustment pedal (C) to desired position:

(Extra-Low), (Low), (Medium) or (High).

H

EIGHT ADJUSTMENT LED INDICATORS

The LEDs show the carpet pile covered by the selected height, e.g.: when (High) is selected, all LEDs will be lit, since this height covers all pile heights. So if (Extra-Low) is selected, only the lowest LED will be lit.

FLOOR HEIGHT

AD0022

E

D

2.4 WAND LENGTH ADJUSTMENT

Extend (E) or shorten (F) the wand to comfortable work position by holding the wand grip (G) in one hand and sliding the upper section (the one with the prongs) with the other hand.

F

G

AD0024 AD0023

2.5 EDGE CLEANER

Brush extends full width for effective edge cleaning along both sides of nozzle. To operate, simply run cleaner along edge board. Rubber bumper protects furniture and baseboards.

- 4 -

2. HOW TO USE POWER BRUSH/WAND (

CONT

’

D

)

2.6 ELECTRONIC CIRCUIT BREAKER

The power brush is equipped with an electronic circuit breaker that protects the motor and the belt if a too large object is picked up accidentally.

If the power brush stops while vacuuming, turn the power unit off using handle. Release the power brush from the wand and turn it over to see if there is an obstruction. When brush roll jam has been cleared, press the reset button (H) and connect the power brush back to the wand. Finally, turn the power unit/power brush back on. If it fails to restart or continues to trip without any apparent reason, the power brush must be serviced by an authorized service center.

AD0030

H

3. CLEANING AND STORAGE

Disconnect electrical supply before servicing or cleaning the unit.

Failure to do so can result in electrical shock or personal injury from cleaner suddenly starting.

3.1 CLEANING BRUSH ROLL

In order to keep high cleaning efficiency and to prevent damage to your vacuum cleaner, the brush roll must be cleaned every time the belt is changed.

The brush roll must also be cleaned according to the following schedule:

V

ACCUM CLEANER USE

Heavy (used daily)

Moderate (2-3 times per week)

Light (once a week)

C

LEAN BRUSH

Every week

Every month

ROLL

Every 2 months

Check and remove hair, string and lint build-up frequently in the brush roll and end cap areas. Remove any dirt or debris in the belt path and in the brush roll areas.

3.2 CLEANING HOUSING

To keep the power brush housing clean, it can be wiped with a damp cloth and a mild soap solution, then thoroughly dried. Never use any type of chemical as they can damage the housing.

3.3 STORAGE

 Ensure that hose and power cord are disconnected from wall inlet before unplugging power brush.

 Disconnect hose handle from wand.

 Always keep hose neatly coiled when not in use.

 When not in use, the power brush should be stored in a clean, dry place.

- 5 -

4. MAINTAINING THE POWER BRUSH

Disconnect electrical supply before servicing or cleaning the unit.

Failure to do so can result in electrical shock or personal injury from cleaner suddenly starting.

4.1 HOW TO CHANGE BELT

 Turn power brush over and using a Phillips no. 2

F

IG

. 1 R

ETAINING

S

CREWS retaining screws (F

IG

. 1) and set aside.

 Remove brush roll cover (F

IG

. 2).

 To free brush roll from base, start by sliding the belt side end and pull brush roll sideways (1).

Once disengaged from housing, lift brush roll (2) out of its compartment (F IG . 3).

 Disengage brush roll from worn belt and extract the belt from motor shaft by a twisting motion in the enlarge area (I) specifically made for that purpose (F

IG

. 4).

 Install new belt by reversing steps  to .

AB0010

F

IG

. 2

NOTE: To ease belt replacement, start by inserting one end around the motor shaft in the enlarged area (I). Insert brush roll through belt until belt is seated in its place. Push

AB0011 down brush roll back in place.

F

IG

. 3

4.2 HOW TO CHANGE BRUSH ROLL

Replace brush roll when brush roll brissles are worn to the base support bars level.

 Turn power brush over and using a Phillips no. 2 screwdriver, remove the 3 brush roll cover retaining screws (F IG . 1) and set aside.

 Remove brush roll cover. (F

IG

. 2).

 To free brush roll from base, start by sliding the belt side end and pull brush roll sideways (1).

Once disengaged from housing, lift brush roll (2) out of its compartment (F

IG

. 3).

I

1

AB0012

F

IG

. 4

2

 Disengage brush roll from belt. Discard worn brush roll.

AB0013

 Insert new brush roll through belt until belt is seated in its place. Push down brush roll back in place.

 Finalise the installation by reversing steps  to .

B

ELT

B

RUSH

R

OLL

2

- 6 -

5. WAND AND HOSE COMPATIBILITY

W

AND

P

ART

N

O

. 08949

V

ACUUM

H

OSE

P

ART

N

OS

.

09007, 09008,

BN32DV & 306330DV

AD0037

AD0038

NOTE: If your dual voltage hose is not compatible with your new 30635615 power brush, please contact Venmar customer service at 1-844-670-2334 to receive a free electrical cord (part no. CRD400-01) that will enable you to connect your new power brush to your hose.

IMPORTANT: Do not return the brush to your retail store.

6. SERVICE PARTS

3

1

2

4

5

AA0002

K

EY

N

O

.

1

2

3

P

ART

N

09234

09233

09236

O

.

Belt

Brush Roll

D

ESCRIPTION

Brush Roll Cover with Screws

4

5

09235

18651

Wand Release Pedal

Wand

Order Service Parts by “Part No.”, not by “Key No.”

R

EPLACEMENT

P

ARTS AND

R

EPAIRS

In order to ensure your unit remains in good working condition, you must use Venmar Ventilation

ULC genuine replacement parts only. Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certification standards and maintain a high standard of safety. Any third party replacement part used may cause serious damage and drastically reduce the performance level of your unit, which will result in premature failing. Venmar Ventilation ULC also recommends to contact a Venmar Ventilation ULC certified service depot for all replacement parts and repairs.

- 7 -

7. SERVICE INFORMATION

To avoid unnecessary service calls, check the belt and brush roll often. Replace the belt if it is stretched or cracked. Clean the brush roll bristles when they are wrapped with thread and hairs. Build-up could cause the brush to rotate unevenly.

The model number and serial number are indicated on the rating label located underneath the power brush. Always refer to these numbers when inquiring about service.

NOTE: The motor is permanently lubricated and sealed. Do not oil the motor at any time.

8. WARRANTY

VENMAR VENTILATION ULC

ONE YEAR LIMITED WARRANTY

Venmar Ventilation ULC warrants to the original consumer purchaser of its products that such products will be free from defects in materials and workmanship for a period of one

(1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Venmar Ventilation ULC will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT APPLY TO CONSUMABLES SUCH AS BELT OR

BRUSH ROLL. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by Venmar Ventilation ULC or an authorized representative), faulty installation or installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty.

VENMAR VENTILATION’S OBLIGATION TO REPAIR OR REPLACE, AT VENMAR

VENTILATION’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE RE-

MEDY UNDER THIS WARRANTY. VENMAR VENTILATION ULC SHALL NOT BE LIABLE

FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN

CONNECTION WITH PRODUCT USE OR PERFORMANCE. This warranty supersedes all prior warranties.

Warranty service is to be completed by an authorized Service Center designated by Venmar

Ventilation ULC. Where applicable, in home service will be made available only in areas where a contracted service provider offers service. If in home service is not available, the product will be repaired or replaced, at Venmar Ventilation’s discretion, by the nearest authorized service provider. The unit removal and reinstallation works are under the customer responsibility, and Venmar Ventilation ULC cannot be charged for them.

To qualify for warranty service, you must (a) notify Venmar Ventilation ULC at the address or telephone number stated below (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.

IF YOU NEED ASSISTANCE OR SERVICE:

For the location of your nearest Venmar Ventilation ULC authorized Service Center:

Dial Toll Free: 1-844-670-2334

Please be prepared to provide:

Product model number • Date and proof of purchase • The nature of the difficulty

Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville, Québec J2C 7W9 www.venmar.ca

Released March 2015

Product specifications subject to change without notice.

- 8 -