Samsung M2070FW Xpress 20PPM Mono Multifunction Laser Printer User Manual

User’s Guide
BASIC
BASIC
This guide provides information concerning the installation, basic operation
and troubleshooting on windows.
ADVANCED
This guide provides information about the installation, advanced configuration, operation
and troubleshooting on various OS environments.
Some features may not be available depending on models or countries.
BASIC
1. Introduction
3. Maintenance
Key benefits
5
Ordering supplies and accessories
67
Features by models
7
Available supplies
68
Useful to know
12
Storing the toner cartridge
69
About this user’s guide
13
Redistributing toner
71
Safety information
14
Replacing the toner cartridge
73
Machine overview
19
Monitoring the supplies life
75
Control panel overview
23
Setting the toner low alert
76
Turning on the machine
27
Cleaning the machine
77
Installing the driver locally
28
Tips for moving & storing your machine
83
Reinstalling the driver
29
4. Troubleshooting
2. Menu Overview and Basic Setup
Tips for avoiding paper jams
85
Menu overview
31
Clearing original document jams
86
Machine’s basic settings
36
Clearing paper jams
91
Media and tray
38
Understanding the status LED
95
Basic printing
50
Understanding display messages
98
Basic copying
56
Basic scanning
61
Basic faxing
62
2
BASIC
5. Appendix
Specifications
104
Regulatory information
113
Copyright
126
3
1. Introduction
This chapter provides information you need to know before using the machine.
• Key benefits
5
• Features by models
7
• Useful to know
12
• About this user’s guide
13
• Safety information
14
• Machine overview
19
• Control panel overview
23
• Turning on the machine
27
• Installing the driver locally
28
• Reinstalling the driver
29
Key benefits
Environmentally friendly
Fast high resolution printing
• To save toner and paper, this machine supports Eco feature (see "Eco
printing" on page 54).
• You can print with a resolution of up to 1,200 x 1,200 dpi effective output.
• Fast, on-demand printing.
• To save paper, you can print multiple pages on one single sheet of paper
(see "Using advanced print features" on page 204).
- M207x series
• To save paper, you can print on both sides of the paper (double-sided
printing) (Manual) (see "Using advanced print features" on page 204).
- M2074 series
• To save electricity, this machine automatically conserves electricity by
substantially reducing power consumption when not in use.
• We recommend using recycled paper for saving energy.
▪ For single-side printing, 20 ppm (A4) or 21 ppm (Letter).
▪ For single-side printing, 18 ppm (A4) or 19 ppm (Letter).
Convenience
• Easy Capture Manager allows you to easily edit and print whatever you
captured using the Print Screen key on the keyboard (see "Easy Capture
Manager" on page 237).
• Samsung Easy Document Creator is an application to help users scan,
compile, and save documents in multiple formats, including .epub format.
These documents can be shared via social networking sites or fax (see"Using
Samsung Easy Document Creator" on page 243)
Key benefits
• AnyWeb Print helps you screen-capture, preview, scrap, and print the
screen of Windows Internet Explorer more easily, than when you use the
ordinary program (see "Samsung AnyWeb Print" on page 238).
• Smart Update allows you to check for the latest software and install the
latest version during the printer driver installation process. This is available
only for Windows.
• If you have Internet access, you can get help, support application, machine
drivers, manuals, and order information from the Samsung website,
www.samsung.com > find your product > Support or Downloads.
AirPrint
• AirPrint allows you to wirelessly print directly from iPhone, iPad and iPod
touch running iOS 4.2 or later.
Supports various wireless network setting method
Wide range of functionality and application support
• Using the WPS (Wi-Fi Protected Setup™) button
• Supports various paper sizes (see "Print media specifications" on page 106).
• Print watermark: You can customize your documents with words, such as
“Confidential” (see "Using advanced print features" on page 204).
• Print posters: The text and pictures of each page of your document are
magnified and printed across the multiple sheets of paper and can then be
taped together to form a poster (see "Using advanced print features" on
page 204).
• You can print in various operating systems (see "System requirements" on
page 109).
- You can easily connect to a wireless network using the WPS button on
the machine and the access point (a wireless router).
• Using the USB cable or a network cable
- You can connect and set various wireless network settings using a USB
cable or a network cable.
• Using the Wi-Fi Direct
- You can conveniently print from your mobile device using the Wi-Fi or
Wi-Fi Direct feature.
• Your machine is equipped with a USB interface and/or a network interface.
See "Introducing wireless set up methods" on page 149.
Features by models
Some features and optional goods may not be available depending on model or country.
Operating System
M207x series
M207xW series
M207xF series
M207xFW series
M207xFH series
M207xHW series
Windows
●
●
Mac
●
●
Linux
●
●
Operating System
(●: Included, Blank: Not available)
Software
Software
SPL printer driver
PCL printer driver
PS printer driver
M207x series
M207xW series
M207xF series
M207xFW series
M207xFH series
M207xHW series
●
●
Features by models
Software
XPS printer drivera
M207x series
M207xW series
M207xF series
M207xFW series
M207xFH series
M207xHW series
●
●
●
●
Direct Printing Utility
Samsung Easy Printer Manager Scan to PC settings
●
Fax to PC settings
●
●
Samsung Easy Document Creator
●
●
Samsung Printer Status
●
●
AnyWeb Print
●
●
SyncThru™ Web Service
●
●
(M207xW series only)
(M207xFW series only)
●
●
(M207xW series only)
(M207xFW series only)
●
●
Device Settings
SyncThru Admin Web Service
Easy Eco Driver
Fax
Samsung Network PC Fax
a. For XPS driver, it is only supported for Windows through the Samsung http://www.samsung.com
(●: Included, Blank: Not available)
●
Features by models
Variety feature
Features
Hi-Speed USB 2.0
M207x series
M207xW series
M207xF series
M207xFW series
M207xFH series
M207xHW series
●
●
●
Network Interface Ethernet 10/100 Base TX wired LAN
(M207xFW series /M207xHW series only)
●
●
(M207xW series only)
(M207xFW series /M207xHW series only)
●
●
(M207xW series only)
(M207xFW series /M207xHW series only)
Eco printing (Control panel)
●
●
Duplex (2-sided) printing (Manual)b
●
●
Network Interface 802.11b/g/n wireless LANa
NFC printing/scanning
USB memory interface
Memory module
Mass Storage Device (HDD)
Duplex Automatic Document Feeder (DADF)
Automatic Document Feeder (ADF)
●
Features by models
Features
Fax
M207x series
M207xW series
M207xF series
M207xFW series
M207xFH series
M207xHW series
Multi-send
●
Delay send
●
Priority send
●
Duplex send
●
Secure receive
Duplex print
●
Send/ Receive forward - fax
Send/ Receive forward - email
Send/ Receive forward - server
Scan
Scanning to email
Scanning to SMB server
Scanning to FTP server
Duplex scan
Scan to PC
●
●
Scan to WSD
●
●
(M207xW series only)
(M207xFW series only)
Features by models
Copy
Features
M207x series
M207xW series
M207xF series
M207xFW series
M207xFH series
M207xHW series
ID card copying
●
●
Reduced or enlarged copying
●
●
Collation
●
●
2-up/4-up
●
●
Adjust background
●
●
Poster
Clone
Book
Margin shift
Edge erase
Gray enhance
Duplex copy
a. Depending on your country, wireless LAN card may not be available. For some counties, only 802.11 b/g can be applied. Contact your local Samsung dealer or the retailer where you
bought your machine.
b. Windows only.
(●: Included, Blank: Not available)
Useful to know
The machine does not print.
A paper jam has occurred.
• Open the print queue list and remove the document from the
list (see "Canceling a print job" on page 51).
• Open and close the scan unit (see "Front view" on page 20).
• Remove the driver and install it again (see "Installing the driver
locally" on page 28).
• Select your machine as your default machine in your Windows
(see "Setting your machine as a default machine" on page 203).
• Check the instructions on removing jammed paper in this
manual and troubleshoot accordingly (see "Clearing paper
jams" on page 91).
Printouts are blurry.
Where can I purchase accessories or supplies?
• The toner level might be low or uneven. Shake the toner
cartridge (see "Redistributing toner" on page 71).
• Inquire at a Samsung distributor or your retailer.
• Try a different print resolution setting (see "Opening printing
preferences" on page 52).
• Visit www.samsung.com/supplies. Select your country/region
to view product service information.
• Replace the toner cartridge (see "Toner cartridge" on page 73).
The status LED flashes or remains constantly on.
Where can I download the machine’s driver?
• Turn the product off and on again.
• You can get help, support application, machine drivers,
manuals, and order information from the Samsung website,
www.samsung.com > find your product > Support or
Downloads.
• Check the meanings of LED indications in this manual and
troubleshoot accordingly (see "Understanding the status LED"
on page 95).
About this user’s guide
This user's guide provides information for your basic understanding of the
machine as well as detailed steps to explain machine usage.
•
Read the safety information before using the machine.
•
If you have a problem using the machine, refer to the troubleshooting
chapter.
•
Terms used in this user’s guide are explained in the glossary chapter.
•
All illustrations in this user’s guide may differ from your machine depending
on its options or model you purchased.
•
The screenshots in this administrator’s guide may differ from your machine
depending on the machine’s firmware/driver version.
•
The procedures in this user’s guide are mainly based on Windows 7.
2
General icons
Icon
Text
Description
Caution
Gives users information to protect the machine from
possible mechanical damage or malfunction.
Note
Provides additional information or detailed
specification of the machine function and feature.
1
Conventions
Some terms in this guide are used interchangeably, as below:
•
Document is synonymous with original.
•
Paper is synonymous with media, or print media.
•
Machine refers to printer or MFP.
1. Introduction
13
Safety information
These warnings and precautions are included to prevent injury to you and
others, and to prevent any potential damage to your machine. Be sure to read
and understand all of these instructions before using the machine. After reading
this section, keep it in a safe place for future reference.
4
Operating environment
Warning
3
Important safety symbols
Do not use if the power cord is damaged or if the electrical outlet is
not grounded.
Explanation of all icons and signs used in this chapter
Warning
Hazards or unsafe practices that may result in severe
personal injury or death.
Caution
Hazards or unsafe practices that may result in minor
personal injury or property damage.
Do not attempt.
This could result in electric shock or fire.
Do not place anything on top of the machine (water, small metal or
heavy objects, candles, lit cigarettes, etc.).
This could result in electric shock or fire.
• If the machine gets overheated, it releases smoke, makes
strange noises, or generates an odd odor, immediately turn off
the power switch and unplug the machine.
• The user should be able to access the power outlet in case of
emergencies that might require the user to pull the plug out.
This could result in electric shock or fire.
Do not bend, or place heavy objects on the power cord.
Stepping on or allowing the power cord to be crushed by a heavy
object could result in electric shock or fire.
Do not remove the plug by pulling on the cord; do not handle the
plug with wet hands.
This could result in electric shock or fire.
1. Introduction
14
Safety information
5
Caution
During an electrical storm or for a period of non-operation,
remove the power plug from the electrical outlet.
Operating method
Caution
This could result in electric shock or fire.
Be careful, the paper output area is hot.
Do not forcefully pull the paper out during printing.
Burns could occur.
It can cause damage to the machine.
If the machine has been dropped, or if the cabinet appears
damaged, unplug the machine from all interface connections and
request assistance from qualified service personnel.
Be careful not to put your hand between the machine and paper
tray.
Otherwise, this could result in electric shock or fire.
You may get injured.
If the machine does not operate properly after these instructions
have been followed, unplug the machine from all interface
connections and request assistance from qualified service
personnel.
Be care when replacing paper or removing jammed paper.
Otherwise, this could result in electric shock or fire.
If the plug does not easily enter the electrical outlet, do not
attempt to force it in.
Call an electrician to change the electrical outlet, or this could
result in electric shock.
Do not allow pets to chew on the AC power, telephone or PC
interface cords.
New paper has sharp edges and can cause painful cuts.
When printing large quantities, the bottom part of the paper
output area may get hot. Do not allow children to touch.
Burns can occur.
When removing jammed paper, do not use tweezers or sharp metal
objects.
It can damage the machine.
Do not allow too many papers to stack up in the paper output tray.
It can damage the machine.
This could result in electric shock or fire and/or injury to your pet.
1. Introduction
15
Safety information
Do not block or push objects into the ventilation opening.
Caution
This could result in elevated component temperatures which can
cause damage or fire.
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
This machine's power reception device is the power cord.
To switch off the power supply, remove the power cord from the
electrical outlet.
Before moving the machine, turn the power off and disconnect all
cords. The information below are only suggestions based on the
units weight.If you have a medical condition that prevents you
from lifting, do not lift the machine. Ask for help, and always use
the appropriate amount of people to lift the device safety.
Then lift the machine:
• If the machine weighs under 20 kg (44.09 lbs), lift with 1 person.
• If the machine weighs 20 kg (44.09 lbs) - 40kg (88.18 lbs), lift
with 2 people.
6
Installation / Moving
• If the machine weighs more than 40 kg (88.18 lbs), lift with 4 or
more people.
The machine could fall, causing injury or machine damage.
Warning
Do not place the machine in an area with dust, humidity, or water
leaks.
This could result in electric shock or fire.
Place the machine in the environment where it meets the
operating temperature and humidity specification.
Otherwise, quality problems can occur and cause damage to the
machine.
see "General specifications" on page 104.
Choose a flat surface with enough space for ventilation to place
the machine. Also consider the space required to open the cover
and trays.
The place should be well-ventilated and be far from direct light,
heat, and humidity.
When using the machine for a long period of time or printing a
large number of pages in a non-ventilated space, it could pollute
the air and be harmful to your health. Place the machine in a wellventilated space or open a window to circulate the air periodically.
Do not place the machine on an unstable surface.
The machine could fall, causing injury or machine damage.
1. Introduction
16
Safety information
7
Use only No.26 AWGa or larger, telephone line cord, if necessary.
Maintenance / Checking
Otherwise, it can cause damage to the machine.
Make sure you plug the power cord into a grounded electrical
outlet.
Caution
Otherwise, this could result in electric shock or fire.
Use the power cord supplied with your machine for safe
operation. If you are using a cord which is longer than 2 meters (6
feet) with a 110V machine, then the gauge should be 16 AWG or
larger.
Otherwise, it can cause damage to the machine, and could result
in electric shock or fire.
Do not put a cover over the machine or place it in an airtight
location, such as a closet.
If the machine is not well-ventilated, this could result in fire.
Do not overload wall outlets and extension cords.
This can diminish performance, and could result in electric shock
or fire.
The machine should be connected tothe power level which is
specified on the label.
If you are unsure and want to check the power level you are using,
contact the electrical utility company.
a. AWG: American Wire Gauge
Unplug this product from the wall outlet before cleaning the
inside of the machine. Do not clean the machine with benzene,
paint thinner or alcohol; do not spray water directly into the
machine.
This could result in electric shock or fire.
When you are working inside the machine replacing supplies or
cleaning the inside, do not operate the machine.
You could get injured.
Keep cleaning supplies away from children.
Children could get hurt.
Do not disassemble, repair or rebuild the machine by yourself.
It can damage the machine. Call a certified technician when the
machine needs repairing.
To clean and operate the machine, strictly follow the user's guide
provided with the machine.
Otherwise, you could damage the machine.
1. Introduction
17
Safety information
Keep the power cable and the contact surface of the plug clean
from dust or water.
When storing supplies such as toner cartridges, keep them away
from children.
Otherwise, this could result in electric shock or fire.
Toner dust can be dangerous if inhaled or ingested.
• Do not remove any covers or guards that are fastened with
screws.
Using recycled supplies, such as toner, can cause damage to the
machine.
• Fuser units should only be repaired by a certified service
technician. Repair by non-certified technicians could result in
fire or electric shock.
In case of damage due to the use of recycled supplies, a service
fee will be charged.
• The machine should only be repaired by a Samsung service
technician.
For supplies that contain toner dust (toner cartridge, waste toner
bottle, imaging unit, etc.) follow the instructions below.
• When disposing of the supplies, follow the instructions for
disposal. Refer to the reseller for disposal instructions.
8
Supply usage
Caution
Do not disassemble the toner cartridge.
Toner dust can be dangerous if inhaled or ingested.
Do not burn any of the supplies such as toner cartridge or fuser
unit.
This could cause an explosion or uncontrollable fire.
• Do not wash the supplies.
• For a waste toner bottle, do not reuse it after emptying the
bottle.
If you do not follow the instructions above, it may cause machine
malfunction and environmental pollution. The warranty does not
cover damages caused by a user's carelessness.
When toner gets on your clothing, do not use hot water to wash
it.
Hot water sets toner into fabric. Use cold water.
When changing the toner cartridge or removing jammed paper,
be careful not to let toner dust touch your body or clothes.
Toner dust can be dangerous if inhaled or ingested.
1. Introduction
18
Machine overview
9
Accessories
Power cord
Quick installation guide
Software CDa
Misc. accessoriesb
a. The software CD contains the printer drivers and software applications.
b. Miscellaneous accessories included with your machine may vary by country of purchase and specific model.
1. Introduction
19
Machine overview
10
Front view
• This illustration may differ from your machine depending on your model.
There are various types of machine.
• Some features and optional goods may not be available depending on
model or country (see "Features by models" on page 7).
2
Control panel
8
NFC (Near Field Communication) tag
3
Handle
9
Scanner glass
4
Tray
10
Scan unita b
5
Tray handle
11
Inner cover
6
Output support
12
Toner cartridge
a. Close the scanner lid before opening the scan unit.
b. Be careful not to pinch your fingers.
Type A
1
8
9
10
7
6
2
5
12
11
4
1
Scanner lid
3
7
Output tray
1. Introduction
20
Machine overview
Type B
1
2
1
Document feeder cover
9
2
Document feeder guide
cover
10
3
Document feeder output tray
11
4
Document feeder output
support
12
5
Control panel
13
Scanner glass
6
Handle
14
Scan unita b
7
Tray
15
Inner cover
8
Tray handle
16
Toner cartridge
11
Output support
Output tray
NFC (Near Field Communication) tag
3
4
10
9
5
8
7
6
Scanner lid
a. Close the scanner lid before opening the scan unit.
b. Be careful not to pinch your fingers.
12
13
14
15
16
1. Introduction
21
Machine overview
Type B
11
Rear view
• This illustration may differ from your machine depending on your model.
There are various types of machine.
1
2
• Some features and optional goods may not be available depending on
model or country (see "Features by models" on page 7).
3
4
Type A
5
1
2
1
USB port
2
Network porta
3
Extension telephone socket (EXT.)
4
Telephone line socket (LINE)
5
Power receptacle
a. M207xFW series only.
1
USB port
2
Power receptacle
1. Introduction
22
Control panel overview
• This control panel may differ from your machine depending on its model.
There are various types of control panels.
• Some features and optional goods may not be available depending on
model or country (see "Features by models" on page 7).
4
Menu
Opens Menu mode and scrolls through the available
menus (see "Menu overview" on page 31).
5
Left/Right
Arrows
Scrolls through the options available in the selected
menu and increases or decreases values.
6
Stop/
Clear
Stops an operation at any time.
12
Type A
7
Power/
Wakeup
1
2
3
4
5
6
7
8
14
13
12
11
10
9
8
Power
saver
Goes into sleep mode.
10
OK
Confirms the selection on the screen.
Allows you to copy both sides of an ID card like a
driver’s license on a single side of paper (see "ID card
copying" on page 59).
12
Scan to
Switches between scan and copy mode. The Scan to
LED turns on scan mode and turns off on copy mode
13
Display screen
Shows the current status and displays prompts during
operation.
ID Copy
2
3
Starts a job.
9
11
1
Start
Turns the power on or off, or wakes up the machine
from the power save mode. If you need to turn the
machine off, press this button for more than three
seconds.
Back
Sends you back to the upper menu level.
Status LED
Indicates the status of your machine (see
"Understanding the status LED" on page 95).
Eco
Turns into eco mode to reduce toner consumption and
paper usage when pc-printing and copying only (see
"Eco printing" on page 54).
1. Introduction
23
Control panel overview
13
14
WPS
a
Configures the wireless network connection easily
without a computer (see "Using the WPS button" on
page 151).
Type B
Press this button and the Status LED will start blinking.
If you want to print only the active screen, release the
button when the Status LED stops blinking. If you want
to print the whole screen, release the button while it’s
blinking.
• Print Screen can only be used in the
Windows and Mac operating systems.
Print
Screen
• You can only use this function with USBconnected machine.
1
• When printing the active window/whole
monitor screen using the print screen
button, the machine may use more toner
depending on what is being printed.
2
• You can only use this function if the
machine’s Samsung Easy Printer Manager
program is installed. If you are a Mac OS
user, you need to enable Screen Print
Settings from the Samsung Easy Printer
Manager to use the Print Screen feature.
3
4
5
1
2
3
21
20
19
4
5
18
6
17
7
16
8
9
15
10
11
12
14
13
Darkness
Adjusts the brightness level to make a copy for easier
reading, when the original contains faint markings and
dark images.
ID Copy
Allows you to copy both sides of an ID card like a
driver’s license on a single side of paper (see "ID card
copying" on page 59).
Display screen
Shows the current status and displays prompts during
an operation.
Copy
Fax
Switches to Copy mode.
Switches to Fax mode.
a. M207xW/ M207xFW series only.
6
Menu
Opens Menu mode and scrolls through the available
menus (see "Menu overview" on page 31).
1. Introduction
24
Control panel overview
7
8
9
Left/
Right
Arrows
Numeric keypad
Address
Book
10
Redial/
Pause
Scrolls through the options available in the selected
menu and increases or decreases values.
Dials a number or enters alphanumeric characters (see
"Keypad letters and numbers" on page 197).
Allows you to store frequently used fax numbers or
search for stored fax numbers (see "Storing email
address" on page 195 or "Setting up the fax address
book" on page 198).
Redials the recently sent fax number or received caller
ID in ready mode, or inserts a pause(-) into a fax number
in edit mode (see "Redialing the fax number" on page
225).
11 Stop/
Clear
Stops an operations at any time.
12
Turns the power on or off, or wakes up the machine
from the power save mode. If you need to turn the
machine off, press this button for more than three
seconds.
Power/
Wakeup
13
Start
14 Power
saver
15
On Hook
Dial
When you press this button, you can hear a dial tone.
Then enter a fax number. It is similar to making a call
using speaker phone (see "Receiving manually in Tel
mode" on page 231).
16 OK
Confirms the selection on the screen.
17
Sends you back to the upper menu level.
18
19
Back
Scan
Switches to Scan mode.
Status LED
Indicates the status of your machine (see
"Understanding the status LED" on page 95).
Eco
Turn into eco mode to reduce toner consumption and
paper usage when pc-printing and copying only (see
"Eco printing" on page 54).
20
Starts a job.
Goes into sleep mode.
1. Introduction
25
Control panel overview
21
WPS
a
Configures the wireless network connection easily
without a computer (see "Using the WPS button" on
page 151).
Press this button and the display will Print Screen? on
the display screen. If you want to print only the active
screen, select the Active. If you want to print the whole
screen, select Full.
• Print Screen can only be used in the
Windows and Mac operating systems.
Print
Screen
• You can only use this function with USBconnected machine.
• When printing the active window/whole
monitor screen using the print screen
button, the machine may use more toner
depending on what is being printed.
• You can only use this function if the
machine’s Samsung Easy Printer Manager
program is installed. If you are a Mac OS user,
you need to enable Screen Print Settings
from the Samsung Easy Printer Manager to
use the Print Screen feature.
a. M207xW/ M207xFW series only.
1. Introduction
26
Turning on the machine
1
Connect the machine to the electricity supply first.
Turn the switch on if the machine has a power switch.
Illustrations on this user’s guide may differ from your machine depending
on its options or models. Check your machine type (see "Front view" on
page 20).
2
Power is turned on automatically.
For M207x series, press
(Power/Wakeup) button on the control
panel.
If you want to turn the power off, press and hold
(Power/Wakeup)
button for about 3 seconds.
1. Introduction
27
Installing the driver locally
A locally connected machine is a machine directly attached to your computer
using the cable. If your machine is attached to a network, skip the following
steps below and go on to installing a network connected machine’s driver (see
"Installing driver over the network" on page 140).
4
Follow the instructions in the installation window.
• If you are a Mac or Linux operating systems user, refer to the "Installation
for Mac" on page 131 or "Installation for Linux" on page 133.
• The installation window in this User’s Guide may differ depending on the
machine and interface in use.
• Only use a USB cable no longer than 3 meters (118 inches).
14
Windows
1
Insert the supplied software CD into your CD-ROM drive.
If the installation window does not appear, click Start > All programs >
Accessories > Run.
X:\Setup.exe replacing “X” with the letter, which represents your CDROM drive and click OK.
2
Review and accept the installation agreements in the installation
window. Then, click Next.
3
Select USB connection on the Printer Connection Type screen. Then,
click Next.
1. Introduction
28
Reinstalling the driver
If the printer driver does not work properly, follow the steps below to reinstall
the driver.
15
Windows
1
From the Start menu, select Programs or All Programs > Samsung
Printers > Uninstall Samsung Printer Software.
2
3
Follow the instructions in the installation window.
Insert the software CD into your CD-ROM drive and install the driver
again (see "Installing the driver locally" on page 28).
1. Introduction
29
2. Menu Overview and
Basic Setup
This chapter provides information about the overall menu structure and the basic setup options.
• Menu overview
31
• Media and tray
38
• Basic printing
50
• Basic copying
56
• Basic scanning
61
• Basic faxing
62
Menu overview
The control panel provides access to various menus to set up the machine or use
the machine’s functions.
6
Press
(Stop/Clear) to return to the ready mode.
Items
Options
• This function is not supported for M207x series (see "Control panel
overview" on page 23).
Fax Feature
(M207xF series,
Dark+1- Dark+5
• Some menus may not appear on the display depending on options or
models. If so, it is not applicable to your machine.
M207xFW series)
Light+5- Light+1
• Some menu names may differ from your machine depending on its
options or the models.
Darkness
Resolution
Normal
Standard
Fine
• The menus are described in the Advanced Guide (see "Useful Setting
Menus" on page 178).
Super Fine
Photo Fax
Color Fax
1
Original Size
Accessing the menu
1
2
3
4
5
Multi Send
Select the Fax, Copy, or Scan button on the control panel depending on
the feature to be used.
Delay Send
Select
(Menu) until the menu you want appears on the bottom line
of the display and press OK.
Send Forward
Forward to Fax
Rcv.Forward
Forward to Fax
Priority Send
Forward to PC
Press the arrows until the needed menu item appears and press OK.
Forward & Print
If the setting item has sub menus, repeat step 3.
Press OK to save the selection.
Secure Receive
Off
On
Print
2. Menu Overview and Basic Setup
31
Menu overview
Items
Options
Fax Feature
(Continue)
Add Page
Fax Setup
Sending
(M207xF
series,M207xFW
series)
Items
Fax Setup
(Continue)
Cancel Job
Options
Receiving
Receive Mode
Ring To Answer
Stamp RCV Name
Redial Times
RCV Start Code
Redial Term
Auto Reduction
Prefix Dial
Discard Size
ECM Mode
Junk Fax Setup
Fax Confirm
DRPD Modea
Image TCR
Change Default
Dial Modea
Resolution
Darkness
Original Size
Manual TX/RX
Manual TX/RX
On
Off
Copy Feature
Original Size
Reduce/Enlarge
Darkness
Normal
Dark+1- Dark+5
Light+5- Light+1
2. Menu Overview and Basic Setup
32
Menu overview
Items
Copy Feature
Options
Original Type
(Continue)
Collation
Layout
Text
Items
System Setup
Options
Machine Setup
Machine ID
Text/Photo
Fax Number
Photo
Date & Time
On
Clock Mode
Off
Language
Default Mode
Normal
Power Save
2-Up
Auto Power Off
4-Up
Wakeup Event
ID Copy
System Timeout
Adjust Bkgd.
Off
Job Timeout
Auto
Altitude Adj.
Enhance Lev.1
Auto Continueb
Enhance Lev.2
Paper Substit.b
Erase Lev.1- Erase Lev.4
Copy Setup
Change Default
Toner Save
Original Size
Eco Settings
Copies
Reduce/Enlarge
Darkness
Original Type
Paper Setup
Paper Size
Paper Type
Margin
Collation
2. Menu Overview and Basic Setup
33
Menu overview
Items
System Setup
(Continue)
Options
Sound/Volume
Key Sound
Network c
Alarm Sound
(M207xF series,
M207xFW series)
Speaker
Ringer
Report
Items
Options
TCP/IP (IPv4)
BOOTP
Static
TCP/IP (IPv6)
Ethernet
Supplies Info.
Usage Counter
IPv6 Protocol
DHCPv6 Config
Configuration
Demo Page
DHCP
Ethernet Port
Ethernet Speed
Wi-Fi
Fax Received
Wi-Fi ON/OFF
WPS
Fax Sent
Wi-Fi Direct
Schedule Jobs
Wi-Fi Signal
Fax Confirm.
WLAN Default
Junk Fax
Address Book
Protocol Mgr.
HTTP
WINS
Maintenance
CLR Empty Msg.c
SNMPv1/v2t
Supplies Life
UPnP(SSDP)
Image Mgr.
mDNS
TonerLow Alert
SetIP
Serial Number
SLP
Network Conf.
2. Menu Overview and Basic Setup
34
Menu overview
Items
Network
(Continue)
Options
Clear Settings
a. This option may not be available depending on your country.
b. This option only appears if Paper Mismatch is enabled.
c. This option only appears when small amount of toner is left in the cartridge.
2. Menu Overview and Basic Setup
35
Machine’s basic settings
You can set the machine’s settings by using the Device Settings in
Samsung Easy Printer Manager program.
Enter the correct time and date using arrows or numeric keypad (see
"Keypad letters and numbers" on page 197).
• For Windows and Mac users, you set from Samsung Easy Printer
• Month = 01 to 12
• Day = 01 to 31
Manager >
(Switch to advanced mode) > Device Settings, see
"Device Settings" on page 246.
• Year = requires four digits
• Hour = 01 to 12
• Minute = 00 to 59
After installation is complete, you may want to set the machine's default
settings.
•
Clock Mode: You can set your machine to display the current time
using either a 12-hour or 24-hour format.
•
Power Save: When you are not using the machine for a while, use
this feature to save power.
To change the machine’s default settings, follow these steps:
It may be necessary to press OK to navigate to lower-level menus for some
models.
When you press the
1
Select
panel.
2
Select the option you want, then press OK.
received, the product will wake up from the power saving mode.
(Menu) > System Setup > Machine Setup on the control
•
•
Language: change the language that is displayed on the control
panel.
•
Date & Time: When you set the time and date, they are used in delay
fax. They are printed on reports. If, however, they are not correct, you
need to change it for the correct time being.
(Power/Wakeup) button, start printing, or a fax is
3
4
Altitude Adj.: Print quality is affected by atmospheric pressure,
which atmospheric pressure is determined by the height of the
machine above sea level. Before you set the altitude value,
determine the altitude where you are (see "Altitude adjustment" on
page 194).
Select the option you want, then press OK.
Press OK to save the selection.
2. Menu Overview and Basic Setup
36
Machine’s basic settings
5
Press
(Stop/Clear) button to return to ready mode.
Refer to below links to set other settings useful for using the machine.
• See "Entering various characters" on page 197.
• See "Keypad letters and numbers" on page 197.
• See "Setting the paper size and type" on page 45.
• See "Setting up the fax address book" on page 198.
2. Menu Overview and Basic Setup
37
Media and tray
This chapter provides information on how to load print media into your
machine.
• Using print media that does not meet these specifications may cause
problems or require repairs. Such repairs are not covered by Samsung’s
warranty or service agreements.
2
Tray overview
To change the size, you need to adjust the paper guides.
• Make sure not to use the inkjet photo paper with this machine. It could
cause damage to the machine.
• Using inflammable print media can cause a fire.
• Use designated print media (see "Print media specifications" on page
106).
1
The use of inflammable media or foreign materials left in the printer may
lead to overheating of the unit and, in rare cases may cause a fire.
2
1 Paper width guide
2 Tray
Illustrations on this user’s guide may differ from your machine depending
on its options or models. Check your machine type (see "Front view" on
page 20).
If you do not adjust the guide, it may cause paper registration, image skew,
or jamming of the paper.
2. Menu Overview and Basic Setup
38
Media and tray
3
Loading paper in the tray
2
Flex or fan the edge of the paper stack to separate the pages before
loading papers.
3
Place the paper with the side you want to print facing up.
Illustrations on this user’s guide may differ from your machine depending
on its options or models. Check your machine type (see "Front view" on
page 20).
1
Open the tray. Then, adjust the tray size to the media size you are loading
(see "Tray overview" on page 38).
1
2
2. Menu Overview and Basic Setup
39
Media and tray
• Do not push the paper width guide too far causing the media to warp.
• Do not use a paper with a leading-edge curl, it may cause a paper jam or
the paper can be wrinkled.
• If you do not adjust the paper width guide, it may cause paper jams.
4
Squeeze the paper width guide and slide it to the edge of the paper stack
without causing it to bend.
5
When you print a document, set the paper type and size for the tray (see
"Setting the paper size and type" on page 45).
2. Menu Overview and Basic Setup
40
Media and tray
4
5
Manual feeding in the tray
The tray can hold special sizes and types of print material, such as postcards,
note cards, and envelopes (see "Print media specifications" on page 106).
To feed manually in the tray, click the below:
See "Loading paper in the tray" on page 39.
Printing on special media
The table below shows the special media usable in tray.
To change the paper setting set in the machine, set the paper type from the
Printing preferences window > Paper tab > Paper Type (see "Opening
printing preferences" on page 52).
• When using special media, we recommend you feed one sheet at a time
(see "Print media specifications" on page 106).
Tips on using the manual feeding in tray
• If you select Paper > Source > Manual Feeder from your printer driver,
you need to press OK each time you print a page.
• Illustrations on this user’s guide may differ from your machine
depending on its options or models. Check your machine type (see
"Front view" on page 20).
• Load only one type, size and weight of print media at time in the in the
tray.
• To prevent paper jams, do not add paper while printing when there is still
paper in the tray.
• Print media should be loaded face up with the top edge going into the
tray first and be placed in the center of the tray.
To see for paper weights for each sheet, refer to "Print media specifications" on
page 106.
Types
• To ensure printing quality and to prevent paper jams, only load the
available paper (see "Print media specifications" on page 106).
• Flatten any curl on postcards, envelopes, and labels before loading them
into the in the tray.
• When printing on special media, you must follow the loading guidelines
(see "Printing on special media" on page 41).
Traya
Plain
●
Thick
●
Thin
●
Bond
●
Color
●
2. Menu Overview and Basic Setup
41
Media and tray
Types
Traya
Envelope
CardStock
●
Printing successfully on envelopes depends upon the quality of the envelopes.
Labels
●
To print an envelope, place it as shown in the following figure.
Envelope
●
Preprinted
●
Cotton
●
Recycled
●
Archive
●
a. The paper types available manual feeding in tray.
(●: Supported, Blank: Not supported)
•
When selecting envelopes, consider the following factors:
-
Weight: should not exceed 90 g/m2 otherwise; jams may occur.
-
Construction: should lie flat with less than 6 mm curl and should not
contain air.
-
Condition: should not be wrinkled, nicked, nor damaged.
-
Temperature: should resist the heat and pressure of the machine
during operation.
•
Use only well-constructed envelopes with sharp and well-creased folds.
•
Do not use stamped envelopes.
•
Do not use envelopes with clasps, snaps, windows, coated lining, selfadhesive seals, or other synthetic materials.
•
Do not use damaged or poorly made envelopes.
2. Menu Overview and Basic Setup
42
Media and tray
•
Be sure the seam at both ends of the envelope extends all the way to the
corner of the envelope.
Labels
To avoid damaging the machine, use only labels designed for use in laser
printers.
1 Acceptable
2 Unacceptable
•
Envelopes with a peel-off adhesive strip or with more than one flap that
folds over to seal must use adhesives compatible with the machine’s fusing
temperature for 0.1 second about 170°C (338 °F). The extra flaps and strips
might cause wrinkling, creasing, or jams, and may even damage the fuser.
•
For the best print quality, position margins no closer than 15 mm from the
edges of the envelope.
•
Avoid printing over the area where the envelope’s seams meet.
•
•
When selecting labels, consider the following factors:
-
Adhesives: Should be stable at your machine’s fusing temperature
about 170°C (338°F).
-
Arrangement: Only use labels with no exposed backing between them.
Labels can peel off sheets that have spaces between the labels, causing
serious jams.
-
Curl: Must lie flat with no more than 13 mm of curl in any direction.
-
Condition: Do not use labels with wrinkles, bubbles, or other
indications of separation.
Make sure that there is no exposed adhesive material between labels.
Exposed areas can cause labels to peel off during printing, which can cause
paper jams. Exposed adhesive can also cause damage to machine
components.
2. Menu Overview and Basic Setup
43
Media and tray
•
Do not run a sheet of labels through the machine more than once. The
adhesive backing is designed for only a single pass through the machine.
Preprinted paper
•
Do not use labels that are separating from the backing sheet or are wrinkled,
bubbled, or otherwise damaged.
When loading preprinted paper, the printed side should be facing up with an
uncurled edge at the front. If you experience problems with paper feeding, turn
the paper around. Note that print quality is not guaranteed.
Card stock/ Custom-sized paper
•
In the software application, set the margins to at least 6.4 mm (0.25 inches)
away from the edges of the material.
•
Must be printed with heat-resistant ink that will not melt, vaporize, or
release hazardous emissions when subjected to the machine’s fusing
temperature for 0.1 second (about 170°C (338°F)).
•
Preprinted paper ink must be non-flammable and should not adversely
affect machine rollers.
•
Before you load preprinted paper, verify that the ink on the paper is dry.
During the fusing process, wet ink can come off preprinted paper, reducing
print quality.
2. Menu Overview and Basic Setup
44
Media and tray
6
7
Setting the paper size and type
After loading paper in the paper tray, set the paper size and type using the
control panel buttons.
To change the paper setting set in the machine, set the paper type from the
Printing preferences window > Paper tab > Paper Type (see "Opening
printing preferences" on page 52).
It may be necessary to press OK to navigate to lower-level menus for some
models.
1
2
3
4
5
Select
Using the output support
The surface of the output tray may become hot if you print a large number
of pages at once. Make sure that you do not touch the surface, and do not
allow children near it.
The printed pages stack on the output support, and the output support will help
the printed pages to align. The printer sends output to the output tray by
default.
(Menu) button on the control panel.
Press System Setup > Paper Setup > Paper Size or Paper Type.
Select the tray and the option you want.
Press OK to save the selection.
Press
(Stop/Clear) to return to ready mode.
If you want to use special-sized paper such as billing paper, select the Paper
tab > Size > Edit... and set Custom Paper Size Settings in the Printing
Preferences (see "Opening printing preferences" on page 52).
2. Menu Overview and Basic Setup
45
Media and tray
8
Illustrations on this user’s guide may differ from your machine depending
on its options or models. Check your machine type (see "Front view" on
page 20).
Preparing originals
•
Do not load paper smaller than 142 x 148 mm (5.6 x 5.8 inches) or larger than
216 x 356 mm (8.5 x 14 inches).
•
Do not attempt to load the following s of paper, in order to prevent paper
jam, low print quality and machine damage.
-
Carbon-paper or carbon-backed paper
-
Coated paper
-
Onion skin or thin paper
-
Wrinkled or creased paper
-
Curled or rolled paper
-
Torn paper
•
Remove all staples and paper clips before loading.
•
Make sure any glue, ink, or correction fluid on the paper is completely dry
before loading.
•
Do not load originals that include different sizes or weights of paper.
•
Do not load booklets, pamphlets, transparencies, or documents with other
unusual characteristics.
2. Menu Overview and Basic Setup
46
Media and tray
9
Loading originals
1
Lift and open the scanner lid.
You can use the scanner glass or the document feeder to load an original for
copying, scanning, and sending a fax.
Illustrations on this user’s guide may differ from your machine depending
on its options or models. Check your machine type (see "Front view" on
page 20).
On the scanner glass
Using the scanner glass, you can copy or scan originals. You can get the best
scan quality, especially for colored or gray-scaled images. Make sure that no
originals are in the document feeder. If an original is detected in the document
feeder, the machine gives it priority over the original on the scanner glass.
2. Menu Overview and Basic Setup
47
Media and tray
2
Place the original face down on the scanner glass. Align it with the
registration guide at the top left corner of the glass.
• Be careful not to break the scanner glass. You may get hurt.
• Do not put hands while closing the scanner lid. The scanner lid may fall
on your hands and get hurt.
• Do not look the light from inside of the scanner while copying or
scanning. It is harmful to eyes.
In the document feeder
Using the document feeder, you can load up to 40 sheets of paper (80 g/m2, 20
lbs bond) for one job.
1
3
Flex or fan the edge of the paper stack to separate the pages before
loading originals.
Close the scanner lid.
• Leaving the scanner lid open while copying may affect copy quality and
toner consumption.
• Dust on the scanner glass may cause black spots on the printout. Always
keep it clean (see "Cleaning the machine" on page 77).
• If you are copying a page from a book or magazine, lift the scanner lid
until its hinges are caught by the stopper and then close the lid. If the
book or magazine is thicker than 30 mm, start copying with the scanner
lid open.
2. Menu Overview and Basic Setup
48
Media and tray
2
Load the original face up into the document feeder input tray. Make sure
that the bottom of the original stack matches the paper size marked on
the document input tray.
3
Adjust the document feeder width guides to the paper size.
Dust on the document feeder glass may cause black lines on the printout.
Always keep the glass clean (see "Cleaning the machine" on page 77).
2. Menu Overview and Basic Setup
49
Basic printing
For special printing features, refer to the Advanced Guide (see "Using
advanced print features" on page 204).
3
Select your machine from the Select Printer list.
4
The basic print settings including the number of copies and print range
are selected within the Print window.
10
Printing
If you are a Mac or Linux operating systems user, refer to the Advanced
Guide (see "Mac printing" on page 212 or "Linux printing" on page 214).
The following Printing Preferences window is for Notepad in Windows 7.
1
2
Open the document you want to print.
Select Print from the File menu.
To take advantage of the advanced printing features, click Properties or
Preferences from the Print window (see "Opening printing preferences" on
page 52).
5
To start the print job, click OK or Print in the Print window.
2. Menu Overview and Basic Setup
50
Basic printing
11
Canceling a print job
If the print job is waiting in the print queue or print spooler, cancel the job as
follows:
•
You can access this window by simply double-clicking the machine icon
(
•
) in the Windows task bar.
You can also cancel the current job by pressing
(Stop/Clear) on the
control panel.
2. Menu Overview and Basic Setup
51
Basic printing
12
Opening printing preferences
4
Click Properties or Preferences.
• The Printing Preferences window that appears in this user’s guide may
differ depending on the machine in use.
• When you select an option in Printing Preferences, you may see a
warning mark
or . An
mark means you can select that certain
option but it is not recommended, and an
mark means you cannot
select that option due to the machine’s setting or environment.
1
2
3
Open the document you want to print.
Select Print from the file menu. The Print window appears.
Select your machine from the Select Printer.
You can check the machine’s current status pressing the Printer Status
button (see "Using Samsung Printer Status" on page 247).
2. Menu Overview and Basic Setup
52
Basic printing
Using a favorite setting
Select more options and click
(Update), settings will be added to the
Presets you made. To use a saved setting, select it from the Presets dropdown list. The machine is now set to print according to the settings you
have selected.To delete saved settings, select it from the Presets drop-
The Presets option, which is visible on each preferences tab except for the
Samsung tab, allows you to save the current preferences for future use.
To save a Presets item, follow these steps:
1
2
down list and click
(Delete).
You can also restore the printer driver’s default settings by selecting
Default Preset from the Presets drop-down list.
Change the settings as needed on each tab.
Enter a name for the item in the Presets input box.
13
Using help
Click the option you want to know on the Printing Preferences window and
press F1 on your keyboard.
3
Click
saved.
(Add). When you save Presets, all current driver settings are
2. Menu Overview and Basic Setup
53
Basic printing
14
Eco printing
The Eco function cuts toner consumption and paper usage. The Eco function
allows you to save print resources and lead you to eco-friendly printing.
1
Select
(Menu) > System Setup > Machine Setup > Eco Settings on
the control panel.
2
Select the option you want and press OK.
•
If you press the Eco button from the control panel, eco mode is enabled. The
default setting of Eco mode is Multiple Pages per Side (2) and Toner Save.
Default Mode: Select this to turn on or off the eco mode. (Toner
save/2-up)
-
Off: Set the eco mode off.
-
On: Set the eco mode on.
Setting Eco mode on the control panel
If you set the eco mode on with a password from the SyncThru™ Web
Service (Settings tab > Machine Settings > System > Eco > Settings) or
Samsung Easy Printer Manager (Device Settings > Eco), the On force
message appears. You have to enter the password to change the eco mode
status.
If your has machine for +/- buttons on the control panel or the machine is
not supported network (see "Control panel overview" on page 23):
You can set the machine’s settings by using the Device Settings in
Samsung Easy Printer Manager program.
•
• For Windows and Mac users, see "Device Settings" on page 246.
• Accessing menus may differ from model to model (see "Accessing the
menu" on page 31).
• It may be necessary to press OK to navigate to lower-level menus for
some models.
3
Select Temp.: Follow the settings from Syncthru™ Web Service or
Samsung Easy Printer Manager. Before you select this item, you must
set the eco function in SyncThru™ Web Service (Settings tab >
Machine Settings > System > Eco > Settings) or Samsung Easy
Printer Manager (Device Settings > Eco).
-
Default Eco: The machine is set to Default Eco mode.
-
Custom Eco: Change any necessary values.
Press OK to save the selection.
2. Menu Overview and Basic Setup
54
Basic printing
Setting eco mode on the driver
Open the Eco tab to set Eco mode. When you see the eco image (
means the eco mode is currently enabled.
•
), that
The actual amount displayed is only an estimate as the actual amount may
differ depending on the operating system used, computing performance,
application software, connection method, media type [thickness], media
size, job complexity, etc.
Eco options
•
Printer Default: Follows the settings from the machine's control panel.
•
None: Disables Eco mode.
•
Eco Printing: Enables eco mode. Activate the various Eco items you want to
use.
•
Password: If the administrator fixed to enable the Eco mode, you have to
enter the password to change the status.
Result simulator
Result Simulator shows the results of reduced emission of carbon dioxide, used
electricity, and the amount of saved paper in accordance with the settings you
selected.
•
The results are calculated on the basis that the total number of printed
paper is one hundred without a blank page when the Eco mode is disabled.
•
Refers to the calculation coefficient about CO2, energy, and paper from IEA,
the index of Ministry of Internal Affairs and Communication of Japan and
www.remanufacturing.org.uk. Each model has a different index.
•
The power consumption in printing mode refers to the average printing
power consumption of this machine.
2. Menu Overview and Basic Setup
55
Basic copying
15
• For special printing features, refer to the Advanced Guide (see "Copy
menu" on page 180).
• Accessing menus may differ from model to model (see "Accessing the
menu" on page 31 or "Control panel overview" on page 23).
Basic copy
1
• Depending on models or options, some menus may not be supported
(see "Features by models" on page 7).
Select
Or select
(copy) >
(Menu) > Copy Feature on the control panel.
(Menu) > Copy Feature on the control panel.
2
Place a single document (see "Loading originals" on page 47).
3
If you want to customize the copy settings including Reduce/Enlarge,
Darkness, Original, and more by using the control panel buttons (see
"Changing the settings for each copy" on page 57).
4
Enter the number of copies using the arrow or number keypad, if
necessary.
5
Press
(Start).
2. Menu Overview and Basic Setup
56
Basic copying
Darkness
If you need to cancel the copying job during the operation, press
Clear) and the copying will stop.
(Stop/
If you have an original containing faint marking and dark images, you can adjust
the brightness to make a copy that is easier to read.
1
16
Changing the settings for each copy
Your machine provides default settings for copying so that you can quickly and
easily make a copy. However, if you want to change the options for each copy,
use the copy function buttons on the control panel.
• If you press
(Stop/Clear) while setting the copy options, all of the
options you have set for the current copy job will be canceled and
returned to their default status. Or, they will automatically return to their
default status after the machine completes the copy in progress.
• Accessing menus may differ from model to model (see "Accessing the
menu" on page 31).
• It may be necessary to press OK to navigate to lower-level menus for
some models.
Select
(copy) >
control panel.
(Menu) > Copy Feature > Darkness on the
Or select Darkness button on the control panel.
2
Select the option you want and press OK.
For example, the Light+5 being the lightest, and the Dark+5 being the
darkest.
3
Press
(Stop/Clear) to return to ready mode.
Original
The original setting is used to improve the copy quality by selecting the
document for the current copy job.
1
Select
(copy) >
control panel.
Or select
panel.
2
(Menu) > Copy Feature > Original Type on the
(Menu) > Copy Feature > Original Type on the control
Select the option you want and press OK.
2. Menu Overview and Basic Setup
57
Basic copying
•
Text: Use for originals containing mostly text.
•
Text/Photo: Use for originals with mixed text and photographs.
To select from the predefined copy sizes
1
If texts in the printout is blurry, select Text to get the clear texts.
•
3
Or select
panel.
Photo: Use when the originals are photographs.
Press
(Stop/Clear) to return to ready mode.
Reduced or enlarged copy
You can reduce or enlarge the size of a copied image from 25% to 400% when
you copy original documents from the scanner glass.
2
3
(Menu) > Copy Feature > Reduce/Enlarge on
(Menu) > Copy Feature > Reduce/Enlarge on the control
Select the option you want and press OK.
Press
(Stop/Clear) to return to ready mode.
To scale the copy by directly entering the scale rate
1
Select
(copy) >
(Menu) > Copy Feature > Reduce/Enlarge >
Custom on the control panel.
Or select
panel.
• This feature may not be available depending on model or optionalgoods
(see "Variety feature" on page 9).
• If the machine set to Eco mode, reduce and enlarge features are
notavailable.
Select
(copy) >
the control panel.
2
3
4
(Menu) > Copy Feature > Reduce/Enlarge on the control
Enter the copy size you want using the numeric keypad.
Press OK to save the selection.
Press
(Stop/Clear) to return to ready mode.
When you make a reduced copy, black lines may appear at the bottom of
your copy.
2. Menu Overview and Basic Setup
58
Basic copying
17
ID card copying
Your machine can print 2-sided originals on one sheet.
1
Press ID Copy on the control panel.
2
Place the front side of an original facing down on the scanner glass
where arrows indicate as shown. Then, close the scanner lid.
3
4
Place Front Side and Press [Start] appears on the display.
The machine prints one side of the original on the upper half of the paper and
the other side on the lower half without reducing the size of the original. This
feature is helpful for copying a small-sized item such as business card.
• The original must be placed on the scanner glass to use this feature.
• If the machine set to Eco mode, this feature is not available.
• For better image quality, Select
(copy) >
(Menu) > Copy
Feature > Original Type > Photo on the control panel or
Copy Feature > Original Type > Photo.
(Menu) >
Press Start.
Your machine begins scanning the front side and shows Place Back Side
and Press [Start].
2. Menu Overview and Basic Setup
59
Basic copying
5
Turn the original over and place it on the scanner glass where arrows
indicate as shown. Then, close the scanner lid.
6
Press Start.
• If you do not press the
copied.
(Start) button, only the front side will be
• If the original is larger than the printable area, some portions may not be
printed.
2. Menu Overview and Basic Setup
60
Basic scanning
For special scanning features, refer to the Advanced Guide (see "Scan
features" on page 216).
If you see Not Available message, check the port connection, or select
Enable Scan from Device Panel in Samsung Easy Printer Manager >
Switch to advanced mode > Scan to PC Settings.
18
Basic Scanning
3
Select the scan destination you want and press OK.
Default setting is My Documents.
This is the normal and usual procedure for scanning originals.
This is a basic scanning method for USB-connected machine.
• You can create and save the frequently used settings as a profile list. Also
you can add and delete the profile and save each profile to a different
path.
• It may be necessary to press OK to navigate to lower-level menus for
some models.
• To change the Samsung Easy Printer Manager >
advanced mode > Scan to PC Settings.
• If you want to scan using the network, refer to the Advanced Guide (see
"Scanning from network connected machine" on page 217).
1
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
2
Select
(scan) > Scan to PC on the control panel.
OR
4
5
Switch to
Select the option you want and press OK.
Scanning begins.
Scanned image is saved in computer’s C:\Users\users name\My
Documents. The saved folder may differ, depending on your operating
system or the application you are using.
Press Scan to on the control panerl.
2. Menu Overview and Basic Setup
61
Basic faxing
19
• This function is not supported for M207x series (see "Control panel
overview" on page 23).
• For special faxing features, refer to the Advanced Guide (see "Fax
features" on page 225).
Preparing to fax
Before you send or receive a fax, you need to connect the supplied line cord to
your telephone wall jack (see "Rear view" on page 22). Refer to the Quick
Installation Guide how to make a connection. The method of making a
telephone connection is different from one country to another.
• You cannot use this machine as a fax via the internet phone. For more
information ask your internet service provider.
20
• We recommend using traditional analog phone services (PSTN: Public
Switched Telephone Network) when connecting telephone lines to use
a fax machine. If you use other Internet services (DSL, ISDN, VolP), you can
improve the connection quality by using the Micro-filter. The Micro-filter
eliminates unnecessary noise signals and improves connection quality or
Internet quality. Since the DSL Micro-filter is not provided with the
machine, contact your Internet service provider for use on DSL Microfilter.
1 Line port
2 Micro filter
3 DSL modem / Telephone line
(see "Rear view" on page 22).
Sending a fax
When you place the originals, you can use either the document feeder or
the scanner glass. If the originals are placed on both the document feeder
and the scanner glass, the machine will read the originals on the document
feeder first, which has higher priority in scanning.
1
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
2
3
Select
(fax) on the control panel.
Adjust the resolution and the darkness to suit your fax needs (see
"Adjusting the document settings" on page 64).
2. Menu Overview and Basic Setup
62
Basic faxing
4
5
Enter the destination fax number (see "Keypad letters and numbers" on
page 197).
Press
(Start) on the control panel. The machine starts to scan and
send the fax to the destinations.
• If you want to send a fax directly from your computer, use Samsung
Network PC Fax (see "Sending a fax in the computer" on page 226).
• When you want to cancel a fax job, press
machine starts transmission.
4
5
6
(On Hook Dial) on the control
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
Select
Press
(Start) on the control panel when you hear a high-pitched fax
signal from the remote fax machine.
You can use the multiple send feature, which allows you to send a fax to multiple
locations. Originals are automatically stored in memory and sent to a remote
station. After transmission, the originals are automatically erased from memory.
You cannot send faxes with this feature if you chosen super fine as an option
or if the fax is in color.
panel.
2
3
Enter a fax number using the number keypad on the control panel.
Sending a fax to multiple destinations
Sending a fax manually
1
(On Hook Dial) on the control panel.
(Stop/Clear) before the
• If you used the scanner glass, the machine shows the message asking to
place another page.
Perform the following to send a fax using
Press
(fax) on the control panel.
Adjust the resolution and the darkness to suit your fax needs (see
"Adjusting the document settings" on page 64).
1
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
2
3
Select
4
Select
(fax) on the control panel.
Adjust the resolution and the darkness to suit your fax needs (see
"Adjusting the document settings" on page 64).
(Menu) > Fax Feature > Multi Send on the control panel.
2. Menu Overview and Basic Setup
63
Basic faxing
5
Enter the number of the first receiving fax machine and press OK.
21
Receiving a fax
You can press speed dial numbers or select a group dial number using
the
6
(Address book) button.
Enter the second fax number and press OK.
Your machine is preset Fax mode at the factory. When you receive a fax, the
machine answers the call on a specified number of rings and automatically
receives the fax.
The display asks you to enter another fax number to send the document.
22
7
To enter more fax numbers, press OK when Yes appears and repeat
steps 5 and 6.
• You can add up to 10 destinations.
• Once you have entered a group dial number, you cannot enter another
group dial number.
8
When you have finished entering fax numbers, select No at the Another
No.? prompt and press OK.
The machine begins sending the fax to the numbers you entered in the
order in which you entered them.
Multi send report is printed after sending faxes.
Adjusting the document settings
Before starting a fax, change the following settings according to your original’s
status to get the best quality.
It may be necessary to press OK to navigate to lower-level menus for some
models.
Resolution
The default document settings produce good results when using typical textbased originals. However, if you send originals that are of poor quality, or
contain photographs, you can adjust the resolution to produce a higher quality
fax.
2. Menu Overview and Basic Setup
64
Basic faxing
1
Select
panel.
(fax) >
(Menu) > Fax Feature > Resolution on the control
2
Select the option you want and press OK.
•
Standard: Originals with normal sized characters.
•
Fine: Originals containing small characters or thin lines or originals
printed using a dot-matrix printer.
•
Super Fine: Originals containing extremely fine detail. Super Fine
mode is enabled only if the machine with which you are
communicating also supports the Super Fine resolution.
• For memory transmission, Super Fine mode is not available. The
resolution setting is automatically changed to Fine.
• When your machine is set to Super Fine resolution and the fax machine
with which you are communicating does not support Super Fine
resolution, the machine transmits using the highest resolution mode
supported by the other fax machine.
•
Photo Fax: Originals containing shades of gray or photographs.
•
Color Fax: Original with colors.
3
Press
(Stop/Clear) to return to ready mode.
Darkness
You can select the degree of darkness of the original document.
The darkness setting is applied to the current fax job. To change the default
setting (see "Fax menu" on page 182).
1
Select
panel.
2
3
Select a darkness level you want.
Press
(fax) >
(Menu) > Fax Feature > Darkness on the control
(Stop/Clear) to return to ready mode.
• Memory transmission is not available in this mode.
• You can only send a color fax if the machine you are communicating with
supports color fax reception and you send the fax manually.
2. Menu Overview and Basic Setup
65
3. Maintenance
This chapter provides information about purchasing supplies, accessories and maintenance parts available for your
machine.
• Ordering supplies and accessories
67
• Available supplies
68
• Storing the toner cartridge
69
• Redistributing toner
71
• Toner cartridge
73
• Monitoring the supplies life
75
• Setting the toner low alert
76
• Cleaning the machine
77
• Tips for moving & storing your machine
83
Ordering supplies and accessories
Available accessories may differ from country to country. Contact your sales representatives to obtain the list of available supplies, and maintenance parts.
To order Samsung-authorized supplies, accessories, and maintenance parts, contact your local Samsung dealer or the retailer where you purchased your machine.
You can also visit www.samsung.com/supplies, and then select your country/region to obtain the contact information for service.
3. Maintenance
67
Available supplies
When supplies reach the end of their life spans, you can order the followings of supplies for your machine:
Type
Toner cartridge
Average yielda
Approx. 1,000 pages
Part name
MLT-D111S
a. Declared yield value in accordance with ISO/IEC 19752. The number of pages may be affected by operating environment, printing interval, graphics, media type and media size.
Depending on the options, percentage of image area and job mode used, the toner cartridge’s lifespan may differ.
When purchasing new toner cartridges or other supplies, these must be purchased in the same country as the machine you are using. Otherwise, new toner
cartridges or other supplies will be incompatible with your machine due to different configurations of toner cartridges and other supplies according to the specific
country conditions.
Samsung does not recommend using non-genuine Samsung toner cartridge such as refilled or remanufactured toner. Samsung cannot guarantee non-genuine
Samsung toner cartridge's quality. Service or repair required as a result of using non-genuine Samsung toner cartridges will not be covered under the machine’s
warranty.
3. Maintenance
68
Storing the toner cartridge
Toner cartridges contain components that are sensitive to light, temperature
and humidity. Samsung suggests users follow these recommendations to
ensure optimal performance, highest quality, and longest life from your new
Samsung toner cartridge.
Store this cartridge in the same environment in which the printer will be used.
This should be in controlled temperature and humidity conditions. The toner
cartridge should remain in its original and unopened package until installation
– if original packaging is not available, cover the top opening of the cartridge
with paper and store in a dark cabinet.
1
Handling instructions
•
Do not touch the surface of the photoconductive drum in the cartridge.
•
Do not expose the cartridge to unnecessary vibrations or shock.
•
Never manually rotate the drum, especially in the reverse direction; this can
cause internal damage and toner spillage.
2
Opening the cartridge package prior to use dramatically shortens its useful shelf
and operating life. Do not store on the floor. If the toner cartridge is removed
from the printer, follow the instructions below to store the toner cartridge
properly.
•
Store the cartridge inside the protective bag from the original package.
•
Store lying flat (not standing on end) with the same side facing up as if it
were installed in the machine.
•
Do not store consumables in any of the following conditions:
-
Temperature greater than 40°C (104°F).
-
Humidity range less than 20% or greater than 80%.
-
An environment with extreme changes in humidity or temperature.
-
Direct sunlight or room light.
-
Dusty places.
-
A car for a long period of time.
-
An environment where corrosive gases are present.
-
An environment with salty air.
Toner cartridge usage
Samsung Electronics does not recommend or approve the use of non-Samsung
brand toner cartridges in your printer including generic, store brand, refilled, or
remanufactured toner cartridges.
Samsung’s printer warranty does not cover damage to the machine caused
by the use of a refilled, remanufactured, or non-Samsung brand toner
cartridges.
3. Maintenance
69
Storing the toner cartridge
3
Estimated cartridge life
Estimated cartridge life (the life of the toner cartridge yield) depends on the
amount of toner that print jobs require. The actual print yield may vary
depending on the print density of the pages you print on, operating
environment, percentage of image area, printing interval, media type and/or
media size. For example, if you print a lot of graphics, the consumption of the
toner is higher and you may need to change the cartridge more often.
3. Maintenance
70
Redistributing toner
When the toner cartridge is near the end of its life:
•
White streaks or light printing occurs and/or density variation side to side.
•
The Status LED blinks red.
If this happens, you can temporarily improve print quality by redistributing the remaining toner in the cartridge. In some cases, white streaks or light printing will still
occur even after you have redistributed the toner.
Illustrations in this user’s guide may differ from your machine depending on the model and options installed. Check your machine type (see "Front view" on page 20).
• To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. Cover it with a piece of paper, if necessary.
• Do not touch the green area of the toner cartridge. Use the handle on the cartridge to avoid touching this area.
• Do not use sharp objects such as a knife or scissors to open the toner cartridge package. They might scratch the drum of the cartridge.
• If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. Hot water sets toner into fabric.
• When opening a scan unit, hold the document feeder and scan unit together.
3. Maintenance
71
Redistributing toner
2
1
3. Maintenance
72
Replacing the toner cartridge
4
Toner cartridge
Click this link to open an animation about replacing a toner cartridge.
• Shake the toner cartridge thoroughly, it will increase the initial print quality.
• Illustrations in this user’s guide may differ from your machine depending on the model and options installed. Check your machine type (see "Front view" on page
20).
• To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. Cover it with a piece of paper, if necessary.
• Do not touch the green area of the toner cartridge. Use the handle on the cartridge to avoid touching this area.
• Do not use sharp objects such as a knife or scissors to open the toner cartridge package. They might scratch the drum of the cartridge.
• If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. Hot water sets toner into fabric.
• When opening a scan unit, hold the document feeder and scan unit together.
When a toner cartridge has reached the end of life, the machine will stop printing.
3. Maintenance
73
Replacing the toner cartridge
3. Maintenance
74
Monitoring the supplies life
If you experience frequent paper jams or printing problems, check the number of pages the machine has printed or scanned. Replace the corresponding parts, if
necessary.
1
2
3
Select
(Menu) > System Setup > Report > Supplies Info. on the control panel.
Select the option you want and press OK.
•
Total: Displays the total number of pages printed.
•
ADF Scan: Displays the number of pages printed by using the document feeder.
•
Platen Scan: Displays the number of pages scanned by using scanner glass.
•
Supplies Info.: Prints the supply information page.
Press
(Stop/Clear) to return to ready mode.
3. Maintenance
75
Setting the toner low alert
If the amount of toner in the cartridge is low, a message or LED informing the user to change the toner cartridge appears. You can set the option for whether or not
this message or LED appears.
• Accessing menus may differ from model to model (see "Accessing the menu" on page 31).
• It may be necessary to press OK to navigate to lower-level menus for some models.
• You can set the machine’s settings by using the Device Settings in Samsung Easy Printer Manager program.
- For Windows and Mac users, you set from Samsung Easy Printer Manager >
1
2
3
Select
(Switch to advanced mode) > Device Settings.
(Menu) > System Setup > Maintenance > TonerLowAlert on the control panel.
Select the option you want.
Press OK to save the selection.
3. Maintenance
76
Cleaning the machine
If printing quality problems occur or if you use your machine in a dusty environment, you need to clean your machine regularly to keep it in the best printing
condition and use your machine longer.
• Cleaning the cabinet of the machine with cleaning materials containing large amounts of alcohol, solvents, or other strong substances can discolor or distort the
cabinet.
• If your machine or the surrounding area is contaminated with toner, we recommend you use a cloth or tissue dampened with water to clean it. If you use a vacuum
cleaner, toner blows in the air and might be harmful to you.
5
Cleaning the outside
Clean the machine cabinet with a soft, lint-free cloth. Dampen the cloth slightly with water, but be careful not to let any water drip onto or into the machine.
3. Maintenance
77
Cleaning the machine
6
Cleaning the inside
During the printing process, paper, toner, and dust particles can accumulate inside the machine. This buildup can cause print quality problems, such as toner specks
or smearing. Cleaning the inside of the machine clears and reduces these problems.
• To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. Cover it with a piece of paper, if necessary.
• Do not touch the green area of the toner cartridge. Use the handle on the cartridge to avoid touching this area.
• Use a dry lint free cloth when cleaning the inside of the machine, be careful not to damage the transfer roller or any other inside parts. Do not use solvents such
as benzene or thinner. Printing quality problems can occur and cause damage to the machine.
• Use a dry lint-free cloth to clean the machine.
• Turn the machine off and unplug the power cord. Wait for the machine to cool down. If your machine has a power switch, turn the power switch off before
cleaning the machine.
• Illustrations in this user’s guide may differ from your machine depending on the model and options installed. Check your machine type (see "Front view" on page
20).
• When opening a scan unit, hold the document feeder and scan unit together.
3. Maintenance
78
Cleaning the machine
2
1
3. Maintenance
79
Cleaning the machine
7
Cleaning the pickup roller
• Turn the machine off and unplug the power cord. Wait for the machine to cool down. If your machine has a power switch, turn the power switch off before
cleaning the machine.
• Illustrations on this user’s guide may differ from your machine depending on its options or models. Check your machine type (see "Front view" on page 20).
3. Maintenance
80
Cleaning the machine
8
Cleaning the scan unit
Keeping the scan unit clean helps ensure the best possible copies. We suggest that you clean the scan unit at the start of each day and during the day as needed.
• Turn the machine off and unplug the power cord. Wait for the machine to cool down. If your machine has a power switch, turn the power switch off before
cleaning the machine.
• Illustrations on this user’s guide may differ from your machine depending on its options or models. Check your machine type (see "Front view" on page 20).
1
2
Slightly dampen a soft, lint-free cloth or paper towel with water.
Lift and open the scanner lid.
3. Maintenance
81
Cleaning the machine
3
Wipe the surface of the scanner until it is clean and dry.
4
3
1
2
1
2
3
4
4
Scanner lid
Scanner glass
Document feeder glass
White Sheet
Close the scanner lid.
3. Maintenance
82
Tips for moving & storing your machine
•
When moving the machine, do not tilt or turn it upside down. Otherwise, the inside of the machine may be contaminated by toner, which can cause damage to
the machine or reduce print quality.
•
When moving the machine, make sure at least two people are holding the machine securely.
3. Maintenance
83
4. Troubleshooting
This chapter gives helpful information for what to do if you encounter an error.
• Tips for avoiding paper jams
85
• Clearing original document jams
86
• Clearing paper jams
91
• Understanding the status LED
95
• Understanding display messages
98
This chapter gives helpful information for what to do if you encounter an error. If your machine
has a display screen, check the message on the display screen first to solve the error.If you
cannot find a solution to your problem in this chapter, refer to the Troubleshooting chapter in
the Advanced Guide (see "Troubleshooting" on page 249).If you cannot find a solution in the
User's Guide or the problem persists, call for service.
Tips for avoiding paper jams
By selecting the correct media s, most paper jams can be avoided. To avoid paper jams, refer to the following guidelines:
•
Ensure that the adjustable guides are positioned correctly (see "Tray overview" on page 38).
•
Do not remove paper from the tray while your machine is printing.
•
Flex, fan, and straighten paper before loading.
•
Do not use creased, damp, or highly curled paper.
•
Do not mix papers in a tray.
•
Use only recommended print media (see "Print media specifications" on page 106).
4. Troubleshooting
85
Clearing original document jams
When an original document jams in the document feeder, a warning message appears on the display.
To avoid tearing the document, remove the jammed document slowly and carefully.
To prevent document jams, use the scanner glass for thick, thin or mixed paper- originals.
4. Troubleshooting
86
Clearing original document jams
1
Original paper jam in front of scanner
• Illustrations in this user’s guide may differ from your machine depending on the model and options installed. Check your machine type (see "Front view" on page
20).
• This troubleshooting may not be available depending on model or optional goods (see "Variety feature" on page 9).
4. Troubleshooting
87
Clearing original document jams
2
Original paper jam inside of scanner
• Illustrations in this user’s guide may differ from your machine depending on the model and options installed. Check your machine type (see "Front view" on page
20).
• This troubleshooting may not be available depending on model or optional goods (see "Variety feature" on page 9).
4. Troubleshooting
88
Clearing original document jams
4. Troubleshooting
89
Clearing original document jams
3
Original paper jam in exit area of scanner
• Illustrations in this user’s guide may differ from your machine depending on the model and options installed. Check your machine type (see "Front view" on page
20).
• This troubleshooting may not be available depending on model or optional goods (see "Front view" on page 20).
1
2
Remove any remaining pages from the document feeder.
Gently remove the jammed paper from the document feeder.
4. Troubleshooting
90
Clearing paper jams
To avoid tearing the paper, pull the jammed paper out slowly and gently.
4
In tray
Click this link to open an animation about clearing a jam.
Illustrations in this user’s guide may differ from your machine depending on the model and options installed. Check your machine type (see "Front view" on page 20).
4. Troubleshooting
91
Clearing paper jams
5
Inside the machine
Click this link to open an animation about clearing a jam.
• The fuser area is hot. Take care when removing paper from the machine.
• Illustrations in this user’s guide may differ from your machine depending on the model and options installed. Check your machine type (see "Front view" on page
20).
4. Troubleshooting
92
Clearing paper jams
2
1
4. Troubleshooting
93
Clearing paper jams
If you do not see the paper in this area, stop and go to next step:
4. Troubleshooting
94
Understanding the status LED
The color of the LED indicates the machine's current status.
• Some LEDs may not be available depending on model or country (see "Control panel overview" on page 23).
• To resolve the error, look at the error message and its instructions from the troubleshooting part (see "Understanding display messages" on page 98).
• If the problem persists, call a service representative.
4. Troubleshooting
95
Understanding the status LED
LED
Status
Off
Description
The machine is off-line.
Blinking
When the backlight blinks, the machine is receiving or printing data.
On
• The machine is on-line and can be used.
Green
• A minor error has occurred and the machine is waiting for the error to be cleared. Check the display message. When the problem
is cleared, the machine resumes.
Blinking
• Small amount of toner is left in the cartridge. The estimated cartridge lifea of toner is close. Prepare a new cartridge for
replacement. You may temporarily increase the printing quality by redistributing the toner (see "Redistributing toner" on page
71).b
Red
• A toner cartridge has almost reached its estimated cartridge lifea. It is recommended to replace the toner cartridge (see "Toner
cartridge" on page 73).
Status
• The cover is opened. Close the cover.
On
• There is no paper in the tray when receiving or printing data. Load paper in the tray.
• The machine has stopped due to a major error. Check the display message (see "Understanding display messages" on page 98).
• A paper jam has occurred (see "Clearing paper jams" on page 91).
Blinking
The machine is connecting to a wireless network.
On
The machine is connected to a wireless network (see "Wireless network setup" on page 148).
Blinking
Small amount of toner is left in the cartridge. The estimated cartridge lifea of toner is close. Prepare a new cartridge for
replacement.You may temporarily increase the printing quality by redistributing the toner (see "Redistributing toner" on page 71)
On
A toner cartridge has almost reached its estimated cartridge lifea. It is recommended to replace the toner cartridge (see "Toner
cartridge" on page 73).
Blue
Orange
4. Troubleshooting
96
Understanding the status LED
LED
Status
On
(
Blue
Power/
Wakeup )
Off
On
Eco
Description
The machine is in power save mode.
The machine is in ready mode or machine’s power is off.
Eco mode is on.
The default setting of Eco mode is 2-up and toner save.
Green
Off
Eco mode is off.
a. Estimated cartridge life means the expected or estimated toner cartridge life, which indicates the average capacity of print-outs and is designed pursuant to ISO/IEC 19752. The number of pages
may be affected by operating environment, percentage of image area, printing interval, graphics, media and media size. Some amount of toner may remain in the cartridge even when red LED is
on and the printer stops printing.
b. Some LEDs may not be available depending on model or country (see "Control panel overview" on page 23).
4. Troubleshooting
97
Understanding display messages
Messages appear on the control panel display to indicate the machine’s status or errors. Refer to the tables below to understand the messages’ and their meaning,
and correct the problem, if necessary.
• If a message is not in the table, reboot the power and try the printing job again. If the problem persists, call a service representative.
• When you call for service, provide the service representative with the contents of display message.
• Some messages may not appear depending on the model and options installed.
• [error number] indicates the error number.
6
Paper Jam-related messages
Message
Document jam.
Meaning
Suggested solutions
Clear the jam (see "Clearing original document jams" on page 86).
Remove jam
The loaded original document has jammed in the document
feeder.
Jam or empty
• Paper has jammed in the paper feed area.
• Clear the jam (see "In tray" on page 91).
Door open&close
• There is no paper in tray.
• Load paper in tray (see "Loading paper in the tray" on page 39).
Paper Jam
Paper has jammed in the inside machine.
Clear the jam (see "Inside the machine" on page 92).
inside machine
4. Troubleshooting
98
Understanding display messages
7
Toner-related messages
Message
Install Toner
Meaning
Suggested solutions
A toner cartridge is not installed.
Install a toner cartridge.
The toner cartridge you have installed is not for your machine.
Install a Samsung-genuine toner cartridge, designed for your
machine.
Small amount of toner is left in the indicated cartridge. The
estimated cartridge life of toner is close.
Prepare a new cartridge for a replacement. You may temporarily
increase the printing quality by redistributing the toner (see
"Redistributing toner" on page 71).
Cartridge
Not Compatible
Toner cartridge
Prepare new cartridge
4. Troubleshooting
99
Understanding display messages
Message
Replace new cartridge
Meaning
Suggested solutions
The indicated toner cartridge has almost reached its estimated
cartridge life.
• You can choose Stop or Continue as shown on the control panel.
If you select Stop, the printer stops printing and you cannot print
any more without changing the cartridge. If you select Continue,
the printer keeps printing but the printing quality cannot be
guaranteed.
Estimated cartridge life means the expected or
estimated toner cartridge life, which indicates the
average capacity of print-outs and is designed pursuant
to ISO/IEC 19752 (see "Available supplies" on page 68).
The number of pages may be affected by operating
environment, percentage of image area, printing
interval, media, percentage of image area, and media
size. Some amount of toner may remain in the cartridge
even when replace new cartridge appears and the
machine stops printing.
The indicated toner cartridge has reached its estimated
cartridge life. The machine might stop printing.
• Replace the toner cartridge for the best print quality when this
message appears. Using a cartridge beyond this stage can result in
printing quality issues (see "Toner cartridge" on page 73).
Samsung does not recommend using a non-genuine
Samsung toner cartridge such as refilled or remanufactured.
Samsung cannot guarantee a non-genuine Samsung toner
cartridge's quality. Service or repair required as a result of
using non-genuine Samsung toner cartridges will not be
covered under the machine warranty.
Replace the toner cartridge (see "Toner cartridge" on page 73).
4. Troubleshooting
100
Understanding display messages
8
Tray-related messages
Message
Meaning
Suggested solutions
Jam or empty
• Paper has jammed in the paper feed area.
• Clear the jam (see "In tray" on page 91).
Door open&close
• There is no paper in tray.
• Load paper in tray (see "Loading paper in the tray" on page 39).
9
Network-related messages
Message
Network Problem:
Meaning
Suggested solutions
IP Conflict
The network IP address you have set is being used by
someone else.
Check the IP address and reset it if necessary (see "Printing a network
configuration report" on page 137).
#S6-3210
Wireless module is not installed.
Turn off then on.
10
Misc. messages
Message
Door Open
Meaning
The cover is not securely latched.
Suggested solutions
Close the cover until it locks into place.
Close it
4. Troubleshooting
101
Understanding display messages
Message
Meaning
Suggested solutions
Door of scanner is open.
The document feeder cover is not securely latched.
Close the cover until it locks into place.
Error [error number]
The machine unit cannot be controlled.
Reboot the power and try the printing job again. If the problem
persists, please call for service.
The scanner is locked.
Reboot the power. If the problem persists, please call for service.
Turn off then on
Error [error number]
Call for service
Scanner Locked
4. Troubleshooting
102
5. Appendix
This chapter provides product specifications and information concerning applicable regulations.
• Specifications
104
• Regulatory information
113
• Copyright
126
Specifications
1
General specifications
The specification values listed below are subject to change without notice. See www.samsung.com for possible changes in information.
Items
Dimensiona
Width x Length x Height
Description
M207x series
406 x 359.6x 253 mm (15.98 x 14.16 x 9.96 inches)
M207xW series
M207xF series / M207xFW series
406 x 359.6x 308.7mm (15.98 x 14.16 x 12.15 inches)
M207xFH series / M207xHW series
Weighta
Machine with consumables
M207x series
7.4 Kg (16.31 lbs)
M207xW series
M207xF series / M207xFW series
8.47 Kg (18.67lbs)
M207xFH series / M207xHW series
Noise Levelb
Ready mode
Less than 26 dB (A)
Print mode
Less than 50 dB (A)
Copy mode
Scanner glass
Less than 50 dB (A)
Document feeder
Less than 53 dB (A)
Scanner glass
Less than 52 dB (A)
Document feeder
Less than 54 dB (A)
Scan mode
5. Appendix
104
Specifications
Items
Temperature
Humidity
Power ratingc
Power consumption
Description
Operation
10 to 32°C (50 to 89.6°F)
Storage (packed)
-20 to 40°C (-4 to 104°F)
Operation
20 to 80% RH
Storage (packed)
10 to 90% RH
110 volt models
AC 110 - 127 V
220 volt models
AC 220 - 240 V
Average operating mode
Less than 310 W
Ready mode
Less than 30 W
Power save moded
• M207x series: Less than 1.5 W
• M207xW series: Less than 2.1 W ( Wi-Fi Direct off :Less than 1.8 W )
• M207xF series / M207xFH series: Less than 1.9 W
• M207xFW series / M207xHW series: Less than 2.5 W ( Wi-Fi Direct off :Less than 2.3 W )
Wirelessf
a.
b.
c.
d.
e.
f.
Power off modee
Less than 0.45 W
Module
T77H262/SPW-B4319S
Dimensions and weight are measured without a handset and other accessories.
Sound Pressure Level, ISO 7779. Configuration tested: basic machine installation, A4 paper, simplex printing.
See the rating label on the machine for the correct voltage (V), frequency (hertz) and of current (A) for your machine.
The power consumption of power save mode may be affected by machine's status, setting conditions, operating environment.
Power consumption can be completely avoided only when the power cable is not connected.
Wireless models only (see "Features by models" on page 7).
5. Appendix
105
Specifications
2
Print media specifications
Print media weight/Capacitya
Type
Size
Dimensions
Tray
Plain
Manual feeding in trayb
Letter
216 x 279 mm (8.5 x 11 inches)
71 to 85 g/m2 (19 to 23 lbs bond)
71 to 85 g/m2 (19 to 23 lbs bond)
Legal
216 x 356 mm (8.5 x 14 inches)
• 1 sheet
Folio
216 x 330 mm (8.5 x 13 inches)
• 150 sheets of 80 g/m2 (21 lbs
bond)
A4
210 x 297 mm (8.27 x 11.69 inches)
Oficio
216 x 343 mm (8.5 x 13.5 inches)
B5(JIS)
182 x 257 mm (7.17 x 10.12 inches)
B5(ISO)
176 x 250 mm (6.93 x 9.84 inches)
Executive
184 x 267 mm (7.25 x 10.5 inches)
A5
148 x 210 mm (5.83 x 8.27 inches)
Monarch Envelope
98 x 191 mm (3.87 x 7.5 inches)
75 to 90 g/m2 (20 to 24 lbs bond) 75 to 90 g/m2 (20 to 24 lbs bond)
No. 10 Envelope
105 x 241 mm (4.12 x 9.5 inches)
• 10 sheets
DL Envelope
110 x 220 mm (4.33 x 8.66 inches)
C5 Envelope
162 x 229 mm (6.38 x 9.02 inches)
• 1 sheet
Envelope
5. Appendix
106
Specifications
Print media weight/Capacitya
Type
Size
Dimensions
Manual feeding in trayb
Tray
Refer to the Plain section
Thick
Refer to the Plain
section
Colored
Refer to the Plain
section
Refer to the Plain
section
Recycled
Refer to the Plain
section
• 1 sheet
75 to 90 g/m2 (20 to 24 lbs bond) 75 to 90 g/m2 (20 to 24 lbs bond)
• 150 sheets of 80 g/m2 (21 lbs
bond)
Refer to the Plain section
• 1 sheet
75 to 90 g/m2 (20 to 24 lbs bond) 75 to 90 g/m2 (20 to 24 lbs bond)
• 150 sheets of 80 g/m2 (21 lbs
bond)
Refer to the Plain section
• 1 sheet
75 to 90 g/m2 (20 to 24 lbs bond) 75 to 90 g/m2 (20 to 24 lbs bond)
• 150 sheets of 80 g/m2 (21 lbs
bond)
Refer to the Plain section
Preprinted
60 to 70 g/m2 (16 to 19 lbs bond) 60 to 70 g/m2 (16 to 19 lbs bond)
• 160 sheets of 60 g/m2 (16 lbs
bond)
Refer to the Plain section
Refer to the Plain
section
• 1 sheet
• 50 sheets of 120 g/m (32 lbs
bond)
Refer to the Plain
section
Cotton
86 to 120 g/m2 (23 to 32 lbs bond)
2
Refer to the Plain section
Thin
86 to 120 g/m2 (23 to 32 lbs
bond)
• 1 sheet
60 to 90 g/m2 (16 to 24 lbs bond) 60 to 90 g/m2 (16 to 24 lbs bond)
• 150 sheets of 80 g/m2 (21 lbs
bond)
• 1 sheet
5. Appendix
107
Specifications
Print media weight/Capacitya
Type
Size
Dimensions
Tray
Labelsc
CardStock
Letter, Legal, Oficio,
Folio, A4, B5(JIS),
B5(ISO), Executive,
A5
Refer to the Plain section
Letter, Legal, Oficio,
Folio, A4, B5(JIS),
B5(ISO), Executive,
A5,
Refer to the Plain section
120 to 150 g/m2 (32 to 40 lbs
bond)
Manual feeding in trayb
120 to 150 g/m2 (32 to 40 lbs bond)
• 1 sheet
• 10 sheets
121 to 163 g/m2 (32 to 43 lbs
bond)
121 to 163 g/m2 (32 to 43 lbs bond)
• 1 sheet
• 10 sheets
Postcard 4x6
Bond
Refer to the Plain
section
Refer to the Plain section
• 10 sheets
• 1 sheet
Archive
Refer to the Plain
section
Refer to the Plain section
• 100 sheets
• 1 sheet
Minimum size (custom)
76 x 127 mm (3 x 5 inches)
60 to 163 g/m2 (16 to 43 lbs bond)
Maximum size (custom)
216 x 356 mm (8.5 x 14 inches)
a. Maximum capacity may differ depending on media weight, thickness, and environmental conditions.
b. 1 sheet for manual feeding.
c. The smoothness of the labels used in this machine is 100 to 250 (sheffield). This means the numeric level of smoothness.
5. Appendix
108
Specifications
3
System requirements
Microsoft® Windows®
Requirement (recommended)
Operating system
CPU
RAM
free HDD space
Windows® XP
Intel® Pentium® III 933 MHz (Pentium IV 1 GHz)
128 MB (256 MB)
1.5 GB
Windows Server® 2003
Intel® Pentium® III 933 MHz (Pentium IV 1 GHz)
128 MB (512 MB)
1.25 GB to 2 GB
Windows Server® 2008
Intel® Pentium® IV 1 GHz (Pentium IV 2 GHz)
512 MB (2 GB)
10 GB
Windows Vista®
Intel® Pentium® IV 3 GHz
512 MB (1 GB)
15 GB
Windows® 7
Intel® Pentium® IV 1 GHz 32-bit or 64-bit processor or higher
1 GB (2 GB)
16 GB
• Support for DirectX® 9 graphics with 128 MB memory (to enable the Aero theme).
• DVD-R/W Drive
Windows Server® 2008 R2
Intel® Pentium® IV 1.4 GHz (x64) or 1.4 GHz (x64) processors (2 GHz or faster)
512 MB (2 GB)
10 GB
Windows® 8
Intel® Pentium® IV 1 GHz 32-bit or 64-bit processor or higher
2 GB
20 GB
Windows® 8.1
• Support for DirectX® 9 graphics with 128 MB memory (to enable the Aero theme).
512 MB (2 GB)
32 GB
• DVD-R/W Drive
Windows Server® 2012
Intel® Pentium® IV 1.4 GHz (x64) or 1.4 GHz (x64) processors (2 GHz or faster)
Windows Server® 2012 R2
5. Appendix
109
Specifications
• Internet Explorer 6.0 or higher is the minimum requirement for all Windows operating systems.
• Users who have administrator rights can install the software.
• Windows Terminal Services is compatible with your machine.
• For Windows 2000, Services Pack 4 or higher is required.
Mac
Requirements (Recommended)
Operating system
CPU
Mac OS X 10.5
• Intel® processors
RAM
Free HDD space
512 MB (1 GB)
1 GB
• 867 MHz or faster Power PC G4/G5
Mac OS X 10.6
• Intel® processors
1 GB (2 GB)
1 GB
Mac OS X 10.7 ~ 10.9
• Intel® processors
2 GB
4 GB
5. Appendix
110
Specifications
Linux
Items
Operating system
Requirements
Redhat® Enterprise Linux 5, 6
Fedora 11, 12, 13, 14, 15, 16, 17, 18
SuSE Linux 10.1 (32 bit)
OpenSuSE® 11.0, 11.1, 11.2, 11.3, 11.4, 12.1, 12.2, 12.3
Ubuntu 10.04, 10.10, 11.04, 11.10, 12.04, 12.10
SuSE Linux Enterprise Desktop 10, 11
Debian 5.0, 6.0
Mint 13, 14
CPU
Pentium IV 2.4GHz (Intel Core™2)
RAM
512 MB (1 GB)
Free HDD space
1 GB (2 GB)
5. Appendix
111
Specifications
4
Network environment
Network and wireless models only (see "Features by models" on page 7).
You need to set up the network protocols on the machine to use it as your network machine. The following table shows the network environments supported by the
machine.
Items
Network interface
Specifications
• Ethernet 10/100 Base-TX Wired Lan
• 802.11b/g/n Wireless LAN
Network operating system
• Server 2003 /Server 2008/XP/Vista/7/Server 2008 R2
• Various Linux OS
• Mac OS X 10.5 ~10.9
Network protocols
• TCP/IPv4
• DHCP, BOOTP
• DNS, WINS, Bonjour, SLP, UPnP
• Standard TCP/IP Printing (RAW), LPR, IPP, WSD
• SNMPv 1/2/3, HTTP, IPSec
• TCP/IPv6 (DHCP, DNS, RAW, LPR, SNMPv 1/2/3, HTTP, IPSec)
Wireless security
• Authentication: Open System, Shared Key, WPA Personal, WPA2 Personal (PSK)
• Encryption: WEP64, WEP128, TKIP, AES
5. Appendix
112
Regulatory information
This machine is designed for a normal work environment and certified with
several regulatory statements.
When using this product, these basic safety precautions should always be
followed to reduce risk of fire, electric shock, and injury to persons:
5
Laser safety statement
The printer is certified in the U.S. to conform to the requirements of DHHS 21
CFR, chapter 1 Subchapter J for Class I(1) laser products, and elsewhere is
certified as a Class I laser product conforming to the requirements of IEC 608251 :2007.
Class I laser products are not considered to be hazardous. The laser system and
printer are designed so there is never any human access to laser radiation above
a Class I level during normal operation, user maintenance or prescribed service
condition.
Warning
Never operate or service the printer with the protective cover removed from
laser/scanner assembly. The reflected beam, although invisible, can damage
your eyes.
5. Appendix
113
Regulatory information
6
8
Ozone safety
Power saver
This product’s ozone emission rate is under 0.1 ppm. Because
ozone is heavier than air, keep the product in a place with good
ventilation.
This printer contains advanced energy conservation technology that
reduces power consumption when it is not in active use.
When the printer does not receive data for an extended period of
time, power consumption is automatically lowered.
7
ENERGY STAR and the ENERGY STAR mark are registered U.S. marks.
Mercury Safety
For more information on the ENERGY STAR program see http://
www.energystar.gov
For ENERGY STAR certified models, the ENRGY STAR label will be on
your machine. Check if your machine is ENERGY STAR certified.
Contains Mercury, Dispose According to Local, State or Federal
Laws.(U.S.A. only)
9
Recycling
Recycle or dispose of the packaging material for this product in an
environmentally responsible manner.
5. Appendix
114
Regulatory information
10
11
Correct disposal of this product (Waste electrical &
electronic equipment)
China only
(Applicable in countries with separate collection
systems)
Website : http://www.samsung.com/cn/support/location/
supportServiceLocation.do?page=SERVICE.LOCATION
襦 愤縑趀爮闭
襦愤縑趀爮闭
賉帞
賉帞
;SUHVV0:
;SUHVV0+:
蜷筨愤竖爮襔*%
縑趀绌裎
術賉縑聱ポM9śJマ
This marking on the product, accessories or literature indicates that the
product and its electronic accessories (e.g. charger, headset, USB cable)
should not be disposed of with other household waste at the end of
their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these
items from other s of waste and recycle them responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details of
where and how they can take these items for environmentally safe
recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for
disposal.
5. Appendix
115
Regulatory information
(The United States of America only)
14
Radio frequency emissions
Dispose unwanted electronics through an approved recycler. To find the nearest
recycling location, go to our website:www.samsung.com/recyclingdirect Or call,
(877) 278 - 0799
12
State of California Proposition 65 Warning (US Only)
13
Taiwan only
FCC information to the user
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
This device may not cause harmful interference, and
•
This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
5. Appendix
116
Regulatory information
•
Consult the dealer or experienced radio TV technician for help.
15
United States of America
Change or modifications not expressly approved by the manufacturer
responsible for compliance could void the user's authority to operate the
equipment.
Federal Communications Commission (FCC)
Intentional emitter per FCC Part 15
Canadian radio interference regulations
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the interference-causing
equipment standard entitled “Digital Apparatus”, ICES-003 of the Industry and
Science Canada.
Cet appareil numérique respecte les limites de bruits radioélectriques
applicables aux appareils numériques de Classe B prescrites dans la norme sur le
matériel brouilleur: “Appareils Numériques”, ICES-003 édictée par l’Industrie et
Sciences Canada.
Low power, Radio LAN devices (radio frequency (RF) wireless communication
devices), operating in the 2.4 GHz/5 GHz Band, may be present (embedded) in
your printer system. This section is only applicable if these devices are present.
Refer to the system label to verify the presence of wireless devices.
Wireless devices that may be in your system are only qualified for use in the
United States of America if an FCC ID number is on the system label.
The FCC has set a general guideline of 20 cm (8 inches) separation between the
device and the body, for use of a wireless device near the body (this does not
include extremities). This device should be used more than 20 cm (8 inches)
from the body when wireless devices are on. The power output of the wireless
device (or devices), which may be embedded in your printer, is well below the
RF exposure limits as set by the FCC.
This transmitter must not be collocated or operation in conjunction with any
other antenna or transmitter.
Operation of this device is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation of the device.
5. Appendix
117
Regulatory information
18
Wireless devices are not user serviceable. Do not modify them in any way.
Modification to a wireless device will void the authorization to use it.
Contact manufacturer for service.
Turkey only
FCC Statement for Wireless LAN use:
19
While installing and operating this transmitter and antenna combination
the radio frequency exposure limit of 1m W/cm2 may be exceeded at
distances close to the antenna installed. Therefore, the user must maintain
a minimum distance of 20cm from the antenna at all times. This device
cannot be colocated with another transmitter and transmitting antenna.
Thai only
20
Canada only
16
Russia/Kazakhstan/Belarus only
This product meets the applicable Industry Canada technical specifications. / Le
present materiel est conforme aux specifications techniques applicables
d’Industrie Canada.
17
Germany only
5. Appendix
118
Regulatory information
The Ringer Equivalence Number (REN) is an indication of the maximum number
of devices allowed to be connected to a telephone interface. The termination of
an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices not exceed five. / L’indice
d’equivalence de la sonnerie (IES) sert a indiquer le nombre maximal de
terminaux qui peuvent etre raccordes a une interface telephonique. La
terminaison d’une interface peut consister en une combinaison quelconque de
dispositifs, a la seule condition que la somme d’indices d’equivalence de la
sonnerie de tous les dispositifs n’excede pas cinq.
The Telephone Company may make changes in its communications facilities,
equipment operations or procedures where such action is reasonably required
in the operation of its business and is not inconsistent with the rules and
regulations in FCC Part 68. If such changes can be reasonably expected to render
any customer terminal equipment incompatible with telephone company
communications facilities, or require modification or alteration of such terminal
equipment, or otherwise materially affect its use or performance, the customer
shall be given adequate notice in writing, to allow the customer an opportunity
to maintain uninterrupted service
21
22
Fax Branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any
person to use a computer or other electronic device to send any message via a
telephone facsimile machine unless such message clearly contains in a margin
at the top or bottom of each transmitted page or on the first page of the
transmission the following information:
1 the date and time of transmission
2 identification of either business, business entity or individual sending the
message; and
3 telephone number of either the sending machine, business, business entity
or individual.
Ringer Equivalence Number
The Ringer Equivalence Number and FCC Registration Number for this machine
may be found on the label located on the bottom or rear of the machine. In some
instances you may need to provide these numbers to the telephone company.
The Ringer Equivalence Number (REN) is a measure of the electrical load placed
on the telephone line, and is useful for determining whether you have
“overloaded” the line. Installing several s of equipment on the same telephone
line may result in problems making and receiving telephone calls, especially
ringing when your line is called. The sum of all Ringer Equivalence Numbers of
the equipment on your telephone line should be less than five in order to assure
proper service from the telephone company. In some cases, a sum of five may
not be usable on your line. If any of your telephone equipment is not operating
properly, you should immediately remove it from your telephone line, as it may
cause harm to the telephone network.
5. Appendix
119
Regulatory information
The equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the rear of this equipment is a label that contains,
among other information, a product identifier in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone company.
FCC Regulations state that changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to
operate this equipment. In the event that terminal equipment causes harm
to the telephone network, the telephone company should notify the
customer that service may be stopped. However, where prior notice is
impractical, the company may temporarily cease service, providing that
they:
a promptly notify the customer.
b give the customer an opportunity to correct the equipment problem.
c inform the customer of the right to bring a complaint to the Federal
Communication Commission pursuant to procedures set out in FCC
Rules and Regulations Subpart E of Part 68.
You should also know that:
•
Your machine is not designed to be connected to a digital PBX system.
•
If you intend to use a computer modem or fax modem on the same phone
line as your machine, you may experience transmission and reception
problems with all the equipment. It is recommended that no other
equipment, except for a regular telephone, share the line with your
machine.
•
If your area experiences a high incidence of lightning or power surges, we
recommend that you install surge protectors for both the power and the
telephone lines. Surge protectors can be purchased from your dealer or
telephone and electronic specialty stores.
•
When programming emergency numbers and/or making test calls to
emergency numbers, use a non-emergency number to advise the
emergency service dispatcher of your intentions. The dispatcher will give
you further instructions on how to actually test the emergency number.
•
This machine may not be used on coin service or party lines.
•
This machine provides magnetic coupling to hearing aids.
You may safely connect this equipment to the telephone network by means of
a standard modular jack, USOC RJ-11C.
23
Replacing the Fitted Plug (for UK Only)
Important
The mains lead for this machine is fitted with a standard (BS 1363) 13 amp plug
and has a 13 amp fuse. When you change or examine the fuse, you must re-fit
the correct 13 amp fuse. You then need to replace the fuse cover. If you have lost
the fuse cover, do not use the plug until you have another fuse cover.
Contact the people from you purchased the machine.
5. Appendix
120
Regulatory information
The 13 amp plug is the most widely used in the UK and should be suitable.
However, some buildings (mainly old ones) do not have normal 13 amp plug
sockets. You need to buy a suitable plug adaptor. Do not remove the moulded
plug.
If you cut off the moulded plug, get rid of it straight away.You cannot rewire
the plug and you may receive an electric shock if you plug it into a socket.
Important warning:
You must earth this machine.
The wires in the mains lead have the following color code:
• Green and Yellow: Earth
• Blue: Neutral
• Brown: Live
If the wires in the mains lead do not match the colors marked in your plug, do
the following:
You must connect the green and yellow wire to the pin marked by the letter “E”
or by the safety ‘Earth symbol’ or colored green and yellow or green.
You must connect the blue wire to the pin which is marked with the letter “N” or
colored black.
You must have a 13 amp fuse in the plug, adaptor, or at the distribution board.
24
Declaration of conformity (European countries)
Approvals and Certifications
Hereby, Samsung Electronics, declares that this [M207x series] is in
compliance with the essential requirements and other relevant
provisions of Low Voltage Directive (2006/95/EC), EMC Directive
(2004/108/EC).
Hereby, Samsung Electronics, declares that this [M207xW series/
M207xF series/M207xFW series] is in compliance with the essential
requirements and other relevant provisions of R&TTE Directive 1999/
5/EC.
The declaration of conformity may be consulted at
www.samsung.com, go to Support > Download center and enter
your printer (MFP) name to browse the EuDoC.
January 1, 1995: Council Directive 2006/95/EC Approximation of the laws of
the member states related to low voltage equipment.
January 1, 1996: Council Directive 2004/108/EC, approximation of the laws of
the Member States related to electromagnetic compatibility.
You must connect the brown wire to the pin which is marked with the letter “L”
or colored red.
5. Appendix
121
Regulatory information
March 9, 1999: Council Directive 1999/5/EC on radio equipment and
telecommunications terminal equipment and the mutual recognition of their
conformity. A full declaration, defining the relevant Directives and referenced
standards can be obtained from your Samsung Electronics Co., Ltd.
representative.
EC Certification
European radio approval information (for products
fitted with EU-approved radio devices)
Low power, Radio LAN type devices (radio frequency (RF) wireless
communication devices), operating in the 2.4 GHz/5 GHz band, may be present
(embedded) in your printer system which is intended for home or office use. This
section is only applicable if these devices are present. Refer to the system label
to verify the presence of wireless devices.
Certification to 1999/5/EC Radio Equipment & Telecommunications Terminal
Equipment Directive (FAX)
This Samsung product has been self-certified by Samsung for pan-European
single terminal connection to the analogue public switched telephone network
(PSTN) in accordance with Directive 1999/5/EC. The product has been designed
to work with the national PSTNs and compatible PBXs of the European
countries:
In the event of problems, you should contact the Euro QA Lab of Samsung
Electronics Co., Ltd. in the first instance.
The product has been tested against TBR21. To assist in the use and application
of terminal equipment which complies with this standard, the European
Telecommunication Standards Institute (ETSI) has issued an advisory document
(EG 201 121) which contains notes and additional requirements to ensure
network compatibility of TBR21 terminals. The product has been designed
against, and is fully compliant with, all of the relevant advisory notes contained
in this document.
Wireless devices that may be in your system are only qualified for
use in the European Union or associated areas if a CE mark with a
Notified Body Registration Number and the Alert Symbol is on the
system label.
The power output of the wireless device or devices that may be embedded in
you printer is well below the RF exposure limits as set by the European
Commission through the R&TTE directive.
European states qualified under wireless approvals:
EU countries
European states with restrictions on use:
EU
In France, the frequency range is restricted to 2454-2483.5 MHz for devices
above 10 mW transmitting power such as wireless
EEA/EFTA countries
5. Appendix
122
Regulatory information
No limitations at this time
25
Israel only
The power output of the wireless device or devices that may be embedded in
your printer is well below the RF exposure limits as known at this time. Because
the wireless devices (which may be embedded into your printer) emit less
energy than is allowed in radio frequency safety standards and
recommendations, manufacturer believes these devices are safe for use.
Regardless of the power levels, care should be taken to minimize human contact
during normal operation.
As a general guideline, a separation of 20 cm (8 inches) between the wireless
device and the body, for use of a wireless device near the body (this does not
include extremities) is typical. This device should be used more than 20 cm (8
inches) from the body when wireless devices are on and transmitting.
26
Regulatory compliance statements
Wireless guidance
Low power, Radio LAN devices (radio frequency (RF) wireless communication
devices), operating in the 2.4 GHz/5 GHz Band, may be present (embedded) in
your printer system. The following section is a general overview of
considerations while operating a wireless device.
Additional limitations, cautions, and concerns for specific countries are listed in
the specific country sections (or country group sections). The wireless devices in
your system are only qualified for use in the countries identified by the Radio
Approval Marks on the system rating label. If the country you will be using the
wireless device in, is not listed, contact your local Radio Approval agency for
requirements. Wireless devices are closely regulated and use may not be
allowed.
This transmitter must not be collocated or operation in conjunction with any
other antenna or transmitter.
Some circumstances require restrictions on wireless devices. Examples of
common restrictions are listed below:
Radio frequency wireless communication can interfere with
equipment on commercial aircraft. Current aviation regulations
require wireless devices to be turned off while traveling in an airplane.
IEEE 802.11 (also known as wireless Ethernet) and Bluetooth
communication devices are examples of devices that provide wireless
communication.
5. Appendix
123
Regulatory information
In environments where the risk of interference to other devices or
services is harmful or perceived as harmful, the option to use a wireless
device may be restricted or eliminated. Airports, Hospitals, and
Oxygen or flammable gas laden atmospheres are limited examples
where use of wireless devices may be restricted or eliminated. When in
environments where you are uncertain of the sanction to use wireless
devices, ask the applicable authority for authorization prior to use or
turning on the wireless device.
Every country has different restrictions on the use of wireless devices.
Since your system is equipped with a wireless device, when traveling
between countries with your system, check with the local Radio
Approval authorities prior to any move or trip for any restrictions on
the use of a wireless device in the destination country.
If your system came equipped with an internal embedded wireless
device, do not operate the wireless device unless all covers and shields
are in place and the system is fully assembled.
Wireless devices are not user serviceable. Do not modify them in any
way. Modification to a wireless device will void the authorization to
use it. Contact manufacturer for service.
Only use drivers approved for the country in which the device will be
used. See the manufacturer System Restoration Kit, or contact
manufacturer Technical Support for additional information.
5. Appendix
124
Regulatory information
27
China only
5. Appendix
125
Copyright
© 2013 Samsung Electronics Co., Ltd. All rights reserved.
This user’s guide is provided for information purposes only. All information included herein is subject to change without notice.
Samsung Electronics is not responsible for any direct or indirect damages, arising from or related to use of this user’s guide.
•
Samsung and the Samsung logo are trademarks of Samsung Electronics Co., Ltd.
•
Microsoft, Windows, Windows Vista, Windows 7, and Windows Server 2008 R2 are either registered trademarks or trademarks of Microsoft Corporation.
•
Microsoft, Internet Explorer, Excel, Word, PowerPoint, and Outlook are either registered trademarks or trademarks of Microsoft Corporation in the United States
and other countries.
•
Google, Picasa, Google Docs, Android and Gmail are either registered trademarks or trademarks of Google Inc.
•
Google Cloud Print is a trademark of Google Inc.
•
iPad, iPhone, iPod touch, Mac and Mac OS are trademarks of Apple Inc., registered in the U.S and other countries.
AirPrint and the AirPrint logo are trademarks of Apple Inc.
•
LaserWriter is a trademark of Apple Computer, Inc.
•
All other brand or product names are trademarks of their respective companies or organizations.
Refer to the 'LICENSE.txt' file in the provided CD-ROM for the open source license information.
REV. 4.00
5. Appendix
126
User’s Guide
ADVANCED
ADVANCED
This guide provides information about installation, advanced configuration,
operation and troubleshooting on various OS environments.
Some features may not be available depending on models or countries.
BASIC
This guide provides information concerning installation, basic operation and troubleshooting
on windows.
ADVANCED
1. Software Installation
3. Useful Setting Menus
Installation for Mac
131
Before you begin reading a chapter
179
Reinstallation for Mac
132
Copy menu
180
Installation for Linux
133
Fax menu
182
Reinstallation for Linux
134
System setup
185
Network setup
191
2. Using a Network-Connected
Machine
4. Special Features
Useful network programs
136
Altitude adjustment
194
Wired network setup
137
Storing email address
195
Installing driver over the network
140
Entering various characters
197
IPv6 configuration
145
Setting up the fax address book
198
Wireless network setup
148
Registering authorized users
202
Samsung Mobile Print
173
Printing features
203
Using the NFC feature
174
Scan features
216
Fax features
225
Using shared folder features
234
Using memory/hard drive features
235
128
ADVANCED
5. Useful Management Tools
Easy Capture Manager
237
Samsung AnyWeb Print
238
Easy Eco Driver
239
Using SyncThru™ Web Service
240
Using Samsung Easy Document Creator
243
Using Samsung Easy Printer Manager
244
Using Samsung Printer Status
247
6. Troubleshooting
Paper feeding problems
250
Power and cable connecting problems
251
Printing problems
252
Printing quality problems
256
Copying problems
264
Scanning problems
265
Faxing problems
267
Operating system problems
269
129
1. Software Installation
This chapter provides instructions for installing essential and helpful software for use in an environment where the
machine is connected via a cable. A locally connected machine is a machine directly attached to your computer using
the cable. If your machine is attached to a network, skip the following steps below and go on to installing a network
connected machine’s driver (see "Installing driver over the network" on page 140).
• Installation for Mac
131
• Reinstallation for Mac
132
• Installation for Linux
133
• Reinstallation for Linux
134
• If you are a Windows OS user, refer to the Basic Guide for installing the machine’s driver (see
"Installing the driver locally" on page 28).
• Only use a USB cable no longer then 3 meter (118 inches).
Installation for Mac
1
Make sure that the machine is connected to your computer and
powered on.
10
Select USB Connected Printer on the Printer Connection Type and
click Continue.
2
Insert the supplied software CD into your CD-ROM drive.
11
Click Add Printer button to select your printer and add it to your printer
list.
If your machine supports fax, click Add Fax button to select your fax and
add it to your fax list
12
3
Double-click the CD-ROM icon that appears on your Mac desktop.
•
4
5
6
7
8
After the installation is finished, click Close.
For Mac OS X 10.8, double-click the CD-ROM that appears on Finder.
Double-click the MAC_Installer folder > Installer OS X icon.
Click Continue.
Read the license agreement and click Continue.
Click Agree to agree to the license agreement.
Click Install. All components necessary for machine operations will be
installed.
If you click Customize, you can choose individual components to install.
9
Enter the password and click OK.
1. Software Installation
131
Reinstallation for Mac
If the printer driver does not work properly, uninstall the driver and reinstall it.
1
Open the Applications folder > Samsung > Printer Software
Uninstaller.
2
3
4
5
To uninstall printer software, click Continue.
Check the program you want to delete and click Uninstall.
Enter the password and click OK.
After the uninstallation is finished, click Close.
If a machine has already been added, delete it from the Print Setup Utility
or Print & Fax.
1. Software Installation
132
Installation for Linux
You need to download Linux software packages from the Samsung website to
install the printer software (http://www.samsung.com > find your product >
Support or Downloads).
1
Installing the Unified Linux Driver
8
9
10
11
When installation finished, launch Printing utility (Go to System >
Administration > Printing or execute “system-config-printer“
command in Terminal program).
Click Add button.
Select your printer.
Click Forward button and add it to your system.
You must log in as a super user (root) to install the machine software. If you
are not a super user, ask your system administrator.
1
Make sure that the machine is connected to your system and powered
on.
2
3
Copy Unified Linux Driver package to your system.
4
5
6
Extract the package.
7
Proceed with installation.
Open Terminal program and go to the folder that you copied the
package to.
Move to uld folder.
Execute ” ./install.sh“ command (If you are not logged in as root,
execute the command with “sudo” as “sudo ./install.sh”).
1. Software Installation
133
Reinstallation for Linux
If the printer driver does not work properly, uninstall the driver and reinstall it.
1
2
3
Open Terminal program.
4
Proceed with uninstallation.
Move to uld folder extracted from Unified Linux Driver package.
Execute ” ./install.sh“ command (If you are not logged in as root,
execute the command with “sudo” as “sudo ./install.sh”).
1. Software Installation
134
2. Using a NetworkConnected Machine
This chapter gives you step-by-step instructions for setting up a network connected machine and software.
• Useful network programs
136
• Wired network setup
137
• Installing driver over the network
140
• IPv6 configuration
145
• Wireless network setup
148
• Samsung Mobile Print
173
• Using the NFC feature
174
Supported optional devices and features may differ according to your model (see "Features by
models" on page 7).
Useful network programs
There are several programs available to setup the network settings easily in a
network environment. For the network administrator especially, managing
several machines on the network is possible.
• Before using the programs below, set the IP address first.
• Some features and optional goods may not be available depending on
model or country (see "Features by models" on page 7).
2
SyncThru™ Web Admin Service
Web-based machine management solution for network administrators.
SyncThru™ Web Admin Service provides you with an efficient way of managing
network devices and lets you remotely monitor and troubleshoot network
machines from any site with corporate Internet access.
•
Download this program from http://solution.samsungprinter.com.
1
3
SyncThru™ Web Service
The web server embedded on your network machine allows you to do the
following tasks (see "Using SyncThru™ Web Service" on page 240).
•
Check the supplies information and status.
•
Customize machine settings.
•
Configure the network parameters necessary for the machine to connect to
various network environments.
SetIP wired network setup
This utility program allows you to select a network interface and manually
configure the IP addresses for use with the TCP/IP protocol.
•
See "IPv4 configuration using SetIP (Windows)" on page 137.
•
See "IPv4 configuration using SetIP (Mac)" on page 138.
• The machine that does not support the network port, it will not be able
to use this feature (see "Rear view" on page 22).
• TCP/IPv6 is not supported by this program.
2. Using a Network-Connected Machine
136
Wired network setup
4
5
Printing a network configuration report
Setting IP address
You can print Network Configuration Report from the machine’s control panel
that will show the current machine’s network settings. This will help you to set
up a network.
• The machine that does not support the network interface, it will not be
able to use this feature (see "Rear view" on page 22).
• TCP/IPv6 is not supported by this program.
•
The machine has the display screen: Press the
(Menu) button on the
control panel and select Network > Network Conf. (Network
Configuration).
•
The machine has the touch screen: Press Setup from the Main screen >
Network > Next > Network Configuration.
•
The machine does not have the display screen: Press the
(Cancel or
First, you have to set up an IP address for network printing and managements.
In most cases a new IP address will be automatically assigned by a DHCP
(Dynamic Host Configuration Protocol) server located on the network.
IPv4 configuration using SetIP (Windows)
Stop/Clear) button for more than 4~5 seconds on the control panel.
Using this Network Configuration Report, you can find your machine’s MAC
address and IP address.
Before using the SetIP program, disable the computer firewall from Control
Panel > Security Center > Windows Firewall.
For example:
•
MAC Address: 00:15:99:41:A2:78
•
IP Address: 169.254.192.192
The following instructions may differ for your model.
1
Download the software from the Samsung website then unpack and
install it: (http://www.samsung.com > find your product > Support or
Downloads).
2
3
Follow the instructions in the installation window.
Connect your machine to the network with a network cable.
2. Using a Network-Connected Machine
137
Wired network setup
4
5
Turn on the machine.
IPv4 configuration using SetIP (Mac)
From the Windows Start menu, select All Programs > Samsung
Printers > SetIP > SetIP.
Before using the SetIP program, disable the computer firewall from System
Preferences > Security > Firewall.
6
Click the
icon (third from left) in the SetIP window to open the TCP/IP
configuration window.
7
Enter the machine’s new information into the configuration window. In
a corporate intranet, you may need to have this information assigned by
a network manager before proceeding.
The following instructions may vary from your model.
1
2
Connect your machine to the network with a network cable.
3
Double-click the CD-ROM icon that appears on your Mac desktop.
Insert the supplied software CD into your CD-ROM drive.
Find the machine’s MAC address from the Network Configuration Report
(see "Printing a network configuration report" on page 137) and enter it
without the colons. For example, 00:15:99:29:51:A8 becomes
0015992951A8.
8
Click Apply, and then click OK. The machine will automatically print the
Network Configuration Report. Confirm that all the settings are
correct.
•
4
5
6
7
For Mac OS X 10.8, Double-click the CD-ROM that appears on Finder.
Double-click the MAC_Installer folder > Installer OS X icon.
Click Continue.
Read the license agreement and click Continue.
Click Agree to agree to the license agreement.
2. Using a Network-Connected Machine
138
Wired network setup
8
Click Install. All components necessary for machine operations will be
installed.
If you click Customize, you can choose individual components to install.
9
10
Enter the password and click OK.
11
Select Network Connected Printer(Wired or Wireless) on the Printer
Connection Type and click Set IP Address button.
12
Click the
icon (third from left) in the SetIP window to open the TCP/IP
configuration window.
13
Enter the machine’s new information into the configuration window. In
a corporate intranet, you may need to have this information assigned by
a network manager before proceeding.
When the message that warns that all applications will close on your
computer appears, click Continue.
Find the machine’s MAC address from the Network Configuration Report
(see "Printing a network configuration report" on page 137) and enter it
without the colons. For example, 00:15:99:29:51:A8 becomes
0015992951A8.
14
Click Apply, and then click OK. The machine will automatically print the
Network Configuration Report. Confirm that all the settings are
correct.
2. Using a Network-Connected Machine
139
Installing driver over the network
• Some features and optional goods may not be available depending on
model or country (see "Features by models" on page 7).
• The machine that does not support the network interface, it will not be
able to use this feature (see "Rear view" on page 22).
Silent installation Mode
Silent installation mode is an installation method that does not require any user
intervention. Once you start the installation, the machine driver and software
are automatically installed on you computer. You can start the silent installation
by typing /s or /S in the command window.
6
Windows
Command-line Parameters
Following table shows commands that can be used in the command window.
1
Make sure that the machine is connected to the network and powered
on. Also, your machine’s IP address should have been set (see "Setting IP
address" on page 137).
2
3
Insert the supplied software CD into your CD-ROM drive.
4
Select Network connection on the Printer Connection Type screen.
Then, click Next.
5
Follow the instructions in the installation window.
Review and accept the installation agreements in the installation
window. Then, click Next.
Following command-line are effective and operated when command is
used with /s or /S. But /h, /H or /? are exceptional commands that can be
operated solely.
Command- line
/s or/S
Definition
Starts silent installation.
Description
Installs machine drivers
without prompting any UIs
or user intervention.
2. Using a Network-Connected Machine
140
Installing driver over the network
Command- line
/p”<port name>”
or/P”<port name>”
Definition
Specifies printer port.
Network Port will
be created by use
of Standard TCP/IP
Port monitor. For
local port, this port
must exist on
system before
being specified by
command.
Description
Printer port name can be
specified as IP address,
hostname, USB local port
name, IEEE1284 port name
or network path.
For example:
• /p”xxx.xxx.xxx.xxx” in
where, “xxx.xxx.xxx.xxx”
means IP address for
network printer. /
p”USB001”, /P”LPT1:”, /
p”hostname”, /
p"\\computer_name\shar
ed_printer" or
"\\xxx.xxx.xxx.xxx\shared
_printer" in where,
"\\computer_name\share
d_printer" or
"\\xxx.xxx.xxx.xxx\shared
_printer" means the
network path to the
printer by entering two
slashes, the computer
name or local IP address
of the PC sharing the
printer, and then the
share name of the printer.
Command- line
Definition
/a”<dest_path>” or/ Specifies destination path
A”<dest_path>”
for installation.
The destination
path should be a
fully qualified path.
Description
Since machine drivers
should be installed on the OS
specific location, this
command applies to only
application software.
/i”<script
Specifies customized install Customized script file can be
filename>” or/
script file for custom
assigned for customized
I”<script filename>” operation.
silent installation. This script
file can be created or
modified through provided
The script filename installer customizing utility
should be a fully
or by text editor.
qualified filename.
This customized
script file is prior than
default installer
setting in setup
package but not
prior than
command-line
parameters.
• When installing the driver
silently in Korean, type inSetup.exe /s /L"0x0012”
or Setup.exe /s.
2. Using a Network-Connected Machine
141
Installing driver over the network
Command- line
Definition
Description
/n”<Printer name>”
or/N”<Printer
name>”
Specifies printer name.
Printer instance shall be
created as specified printer
name.
With this parameter, you can
add printer instances as your
wishes.
/nd or/ND
Commands not to set the
installed driver as a default
machine driver.
It indicates installed machine
driver will not be the default
machine driver on your
system if there are one or
more printer drivers
installed. If there is no
installed machine driver on
your system, then this option
won’t be applied because
Windows OS will set installed
printer driver as a default
machine driver.
/x or/X
Uses existing machine
driver files to create printer
instance if it is already
installed.
This command provides a
way to install a printer
instance that uses installed
printer driver files without
installing an additional
driver.
Command- line
Definition
Description
/up”<printer
name>” or/
UP”<printer
name>”
Removes only specified
printer instance and not
the driver files.
This command provides a
way to remove only specified
printer instance from your
system without effecting
other printer drivers. It will
not remove printer driver
files from your system.
/d or/D
Uninstalls all device drivers
and applications from your
system.
This command will remove
all installed device drivers
and application software
from your system.
/v”<share name>”
or/V”<share
name>”
Shares installed machine
and add other available
platform drivers for Point &
Print.
It will install all supported
Windows OS platform’s
machine drivers to system
and share it with specified
<share name> for point and
print.
/o or /O
Opens Printers and Faxes
folder after installation.
This command will open
Printers and Faxes folder
after the silent installation.
/h, /H or /?
Shows Command-line Usage.
2. Using a Network-Connected Machine
142
Installing driver over the network
7
Mac
1
2
3
Make sure that the machine is connected to your network and powered
on.
Enter the password and click OK.
11
Click Add Printer button to select your printer and add it to your printer
list.
12
13
14
Click IP and select HP Jetdirect - Socket in Protocol.
15
If Auto Select does not work properly, choose Select Printer Software
and your machine name in Print Using.
16
17
Click Add.
Insert the supplied software CD into your CD-ROM drive.
Select Network Connected Printer(Wired or Wireless) on the Printer
Connection Type and click Continue.
Enter the machine’s IP address in the Address input field.
Enter the queue name in the Queue input field. If you cannot determine
the queue name for your machine server, try using the default queue
first.
Double-click the CD-ROM icon that appears on your Mac desktop.
•
4
5
6
7
8
9
10
For Mac OS X 10.8, double-click the CD-ROM that appears on Finder.
Double-click the MAC_Installer folder > Installer OS X icon.
Click Continue.
After the installation is finished, click Close.
Read the license agreement and click Continue.
Click Agree to agree to the license agreement.
Click Install. All components necessary for machine operations will be
installed.
If you click Customize, you can choose individual components to install.
2. Using a Network-Connected Machine
143
Installing driver over the network
8
Linux
You need to download Linux software packages from the Samsung website to
install the printer software (http://www.samsung.com > find your product >
Support or Downloads).
Install the Linux driver and add network printer
1
Make sure that the machine is connected to your network and powered
on. Also, your machine’s IP address should have been set.
2
3
Copy Unified Linux Driver package to your system.
4
5
6
Extract the package.
7
Open Terminal program and go to the folder that you copied the
package to.
Move to uld folder.
Execute ” ./install.sh“ command (If you are not logged in as root,
execute the command with “sudo” as “sudo ./install.sh”).
Proceed with installation.
8
9
10
11
When installation finished, launch Printing utility (Go to System >
Administration > Printing or execute “system-config-printer“
command in Terminal program).
Click Add button.
Select AppSocket/HP JetDirect and enter your machine’s IP address.
Click Forward button and add it to your system.
Add a network printer
1
2
3
4
5
6
7
8
Double-click the Unified Driver Configurator.
Click Add Printer.
The Add printer wizard window opens. Click Next.
Select Network printer and click the Search button.
The printer’s IP address and model name appears on list field.
Select your machine and click Next.
Enter the printer description and click Next.
After the machine is added, click Finish.
2. Using a Network-Connected Machine
144
IPv6 configuration
IPv6 is supported properly only in Windows Vista or higher.
7
If the machine does not work in the network environment, activate IPv6.
Refer to the next section followed by.
• Some features and optional goods may not be available depending on
model or country (see "Features by models" on page 7 or "Menu
overview" on page 31).
In the IPv6 network environment, follow the next procedure to use the IPv6
address.
9
From the control panel
1
2
3
Connect your machine to the network with a network cable.
4
5
6
Select Start > Control Panel > Printers and Faxes.
Turn on the machine.
The Add Printer Wizard window appears. Follow the instructions in the
window.
Activating IPv6
1
2
3
4
5
Press the
(Menu) button on the control panel.
Press Network > TCP/IP (IPv6) > IPv6 Protocol.
Select On and press OK.
Turn the machine off and turn it on again.
Reinstall your printer driver.
Print a Network Configuration Report that will check IPv6 addresses
(see "Printing a network configuration report" on page 137).
Click Add a printer in the left pane of the Printers and Faxes windows.
Click Add a local printer in the Add Printer windows.
2. Using a Network-Connected Machine
145
IPv6 configuration
Setting IPv6 addresses
10
From the SyncThru™ Web Service
The machine supports the following IPv6 addresses for network printing and
managements.
•
Link-local Address: Self-configured local IPv6 address (Address starts with
FE80).
•
Stateless Address: Automatically configured IPv6 address by a network
router.
•
Stateful Address: IPv6 address configured by a DHCPv6 server.
•
Manual Address: Manually configured IPv6 address by a user.
DHCPv6 address configuration (Stateful)
For models that do not have the display screen on the control panel, you
need to access SyncThru™ Web Service first using the IPv4 address and
follow the below procedure to use IPv6.
1
Access a web browser, such as Internet Explorer, from Windows. Enter
the machine IP address (http://xxx.xxx.xxx.xxx) in the address field and
press the Enter key or click Go.
2
If it’s your first time logging into SyncThru™ Web Service you need to
log-in as an administrator. Type in the below default ID and password.
If you have a DHCPv6 server on your network, you can set one of the following
options for default dynamic host configuration.
1
2
3
Press the
•
ID: admin
•
Password: sec00000
(Menu) button on the control panel.
Press Network > TCP/IP (IPv6) > DHCPv6 Config.
3
When the SyncThru™ Web Service window opens, move the mouse
cursor over the Settings of the top menu bar and then click Network
Settings.
4
5
6
Click TCP/IPv6 on the left pane of the website.
Press OK to select the required value you want.
•
Always Use: Always use DHCPv6 regardless of router request.
•
Never Use: Never use DHCPv6 regardless of router request.
•
Router: Use DHCPv6 only when requested by a router.
Check the IPv6 Protocol check box to activate IPv6.
Check the Manual Address check box. Then, the Address/Prefix text
box is activated.
2. Using a Network-Connected Machine
146
IPv6 configuration
7
Enter the rest of the address (e.g.,:3FFE:10:88:194::AAAA. “A” is the
hexadecimal 0 through 9, A through F).
8
9
Choose the DHCPv6 configuration.
Click the Apply button.
Using SyncThru™ Web Service
1
Start a web browser, such as Internet Explorer, that supports IPv6
addressing as a URL.
2
Select one of the IPv6 addresses (Link-local Address, Stateless
Address, Stateful Address, Manual Address) from Network
Configuration Report (see "Printing a network configuration report" on
page 137).
3
Enter the IPv6 addresses (e.g.,: http://[FE80::215:99FF:FE66:7701]).
Address must be enclosed in '[ ]' brackets.
2. Using a Network-Connected Machine
147
Wireless network setup
• Make sure your machine supports wireless networking. Wireless
networking may not be available depending on the model (see "Features
by models" on page 7).
• If the IPv6 network seems to not be working, set all the network settings
to the factory defaults and try again using Clear Setting.
Wireless network name and Network Password
Wireless networks require higher security, so when an access point is first set up,
a network name (SSID), the type of security used, and a Network Password are
created for the network. Ask your network administrator about this information
before proceeding with the machine installation.
11
Getting started
Understanding your network type
Typically, you can only have one connection between your computer and the
machine at a time.
Infrastructure mode
This is an environment generally used for homes and SOHOs
(Small Office/ Home Office). This mode uses an access point to
communicate with the wireless machine.
2. Using a Network-Connected Machine
148
Wireless network setup
12
Introducing wireless set up methods
You can set wireless settings either from the machine or the computer. Choose the setting method from the below table.
Some wireless network installation types may not be available depending on the model or country.
Set up method
Connecting method
From the computer
Description & Reference
A
Windows user, see "Access point via USB cable" on page 155.
B
Windows user, see "Access point without a USB cable (recommended)" on page 158.
C
• Mac user, see "Access point via USB cable" on page 160.
• Mac user, see "Access point without a USB cable (recommended)" on page 163
OR
With Access Point
From the machine’s control
panel
D
See "Using a network cable" on page 165.
E
• See "Machines with a display screen" on page 152.
• See "Machines without a display screen" on page 153.
See "Using the menu button" on page 155.
F
2. Using a Network-Connected Machine
149
Wireless network setup
Set up method
Without Access Point
Connecting method
Description & Reference
Wi-Fi Direct setup
See "Setting up Wi-Fi Direct" on page 168.
G
• If problems occur during wireless set up or driver installation, refer to the troubleshooting chapter (see "Troubleshooting" on page 170).
• It is strongly recommended that you set the password on Access Points. If you do not set the password on Access Points, they might be exposed to illegal access
from unknown machines including PCs, smart phones and printers. Refer to the Access Point user' guide for password settings.
2. Using a Network-Connected Machine
150
Wireless network setup
Choosing your type
13
Using the WPS button
There are two methods available to connect your machine to a wireless network
If your machine and an access point (or wireless router) support Wi-Fi Protected
Setup™ (WPS), you can easily configure the wireless network settings by
pressing the
(WPS) button on the control panel without a computer.
• If you want to use the wireless network using the infrastructure mode,
make sure that the network cable is disconnected from the machine.
Using the WPS (PBC) button or entering the PIN from the computer to
connect to the access point (or wireless router) varies depending on the
access point (or wireless router) you are using. Refer to the user's guide
of the access point (or wireless router) you are using.
• When using the WPS button to set the wireless network, security settings
may change. To prevent this, lock the WPS option for the current wireless
security settings. The option name may differ depending on the access
point (or wireless router) you are using.
using the
(WPS) button on the control panel.
The Push Button Configuration (PBC) method allows you to connect your
machine to a wireless network by pressing both the
(WPS) button on the
control panel of your machine and the WPS (PBC) button on a Wi-Fi Protected
Setup™ WPS-enabled access point (or wireless router) respectively.
The Personal Identification Number (PIN) method helps you connect your
machine to a wireless network by entering the supplied PIN information on a WiFi Protected Setup™ WPS-enabled access point (or wireless router).
Factory default in your machine is PBC mode, which is recommended for a
typical wireless network environment.
You can change the WPS mode in control panel (
Wi-Fi > Wi-Fi Settings).
(Menu) > Network >
Items to prepare
•
Check if the access point (or wireless router) supports Wi-Fi Protected
Setup™ (WPS).
•
Check if your machine supports Wi-Fi Protected Setup™ (WPS).
•
Networked computer (PIN mode only)
2. Using a Network-Connected Machine
151
Wireless network setup
Machines with a display screen
Connecting in PBC mode
1
Press and hold the
2 seconds.
(WPS) button on the control panel for more than
Connecting in PIN mode
1
Press and hold the
2 seconds.
2
The eight-digit PIN appears on the display.
You need to enter the eight-digit PIN within two minutes on the
computer that is connected to the access point (or wireless router).
The machine starts waiting for up to two minutes until you press the WPS
(PBC) button on the access point (or wireless router).
2
The messages are displayed on the display screen in the order below:
Press the WPS (PBC) button on the access point (or wireless router).
a Connecting: The machine is connecting to the wireless network.
The messages are displayed on the display screen in the order below:
b Connected: When the machine is successfully connected to the
wireless network, the WPS LED light stays on.
a Connecting: The machine is connecting to the access point (or
wireless router).
b Connected: When the machine is successfully connected to the
wireless network, the WPS LED light stays on.
c AP SSID: After completing the wireless network connection process,
the AP’s SSID information appears on the display.
3
(WPS) button on the control panel for more than
c SSID Type: After completing the wireless network connection
process, the AP’s SSID information is displayed on the LCD display.
3
Insert the supplied CD into the CD-ROM drive and proceed to install the
software following the directions on the screen. When the "Connect
Printer" screen appears, select Network (Ethernet/Wireless) connection.
Insert the supplied CD into the CD-ROM drive and proceed to install the
software following the directions on the screen. When the "Connect
Printer" screen appears, select the Network (Ethernet/Wireless)
connection.
2. Using a Network-Connected Machine
152
Wireless network setup
Machines without a display screen
Connecting in PBC mode
1
1
2
Press and hold the
(WPS) button on the control panel for more than
4 seconds until the status LED stays on.
The machine starts connecting to the access point (or wireless router).
Press the WPS (PBC) button on the access point (or wireless router).
a The light blinks fast on the WPS LED. The machine is connecting to
the access point (or wireless router).
The network configuration report, including PIN, must be printed (see
"Printing a network configuration report" on page 137).
In ready mode, press and hold the
(Cancel or Stop/Clear) button on
the control panel for about 5 seconds. You can find your machine’s PIN.
Press and hold the
(WPS) button on the control panel for about 2 - 4
seconds until the status LED blinks quickly.
The machine starts connecting to the wireless network. The LED blinks
slowly for up to two minutes until you press the PBC button on the
access point (or wireless router).
2
Connecting in PIN mode
3
You need to enter the eight-digit PIN within two minutes on the
computer that is connected to the access point (or wireless router).
The LED blinks slowly for up to two minutes until you enter the eightdigit PIN.
b When the machine is successfully connected to the wireless
network, the WPS LED light stays on.
The WPS LED blinks in the order below:
3
Insert the supplied CD into the CD-ROM drive and proceed to install the
software following the directions on the screen. When the "Connect
Printer" screen appears, select the Network (Ethernet/Wireless)
connection.
a The light blinks fast on the WPS LED. The machine is connecting to
the access point (or wireless router).
b When the machine is successfully connected to the wireless
network, the WPS LED light stays on.
4
Insert the supplied CD into the CD-ROM drive and proceed to install the
software following the directions on the screen. When the "Connect
Printer" screen appears, select the Network (Ethernet/Wireless)
connection.
2. Using a Network-Connected Machine
153
Wireless network setup
Re-connecting to a network
Disconnecting from a network
When the wireless function is off, the machine automatically tries to re-connect
to the access point (or wireless router) with the previously used wireless
connection settings and address.
To disconnect the wireless network connection, press the
the control panel for more than two seconds.
In the following cases, the machine automatically re-connects to the
wireless network:
• The machine is turned off and on again.
• The access point (or wireless router) is turned off and on again.
(WPS) button on
•
When the Wi-Fi network is in idle mode: The machine is immediately
disconnected from the wireless network and the WPS LED turns off.
•
When the Wi-Fi network is being used: While the machine waits until the
current job is finished, the light blinks fast on the WPS LED. Then, the
wireless network connection is automatically disconnected and the WPS
LED turns off.
Canceling the connection process
To cancel the wireless network connection when the machine is connecting to
the wireless network, press and release the
(Cancel or Stop/Clear) on the
control panel. You need to wait 2 minutes to re-connect to the wireless
network.
2. Using a Network-Connected Machine
154
Wireless network setup
3
14
Using the menu button
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
Before starting, you will need to know the network name (SSID) of your wireless
network and the Network Password if it is encrypted. This information was set
when the access point (or wireless router) was installed. If you do not know
about your wireless environment, please ask the person who set up your
network.
Press the OK to select the setup method you want.
•
Wizard (recommended): In this mode, the setup is automatic. The
machine will display a list of available networks from which to
choose. After a network is chosen then printer will prompt for the
corresponding security key.
•
Custom: In this mode, users can give or edit manually their own SSID
, or choose the security option in detail.
15
Setup using Windows
Shortcut to the Samsung Easy Wireless Setup program without the CD: If
you have installed the printer driver once, you can access the Samsung
Easy Wireless Setup program without the CD (see "Accessing
management tools" on page 290).
After completing the wireless network connection, you need to install a
machine driver to print from an application (see "Installing driver over the
network" on page 140).
Access point via USB cable
1
2
Press the
(Menu) button on the control panel.
Press Network > Wireless > WiFi Settings.
Items to prepare
•
Access point
•
Network-connected computer
•
Software CD that was provided with your machine
2. Using a Network-Connected Machine
155
Wireless network setup
•
A machine installed with a wireless network interface
•
USB cable
5
Select Wireless network connection on the Printer Connection Type
screen. Then, click Next.
6
On the Are you setting up your printer for the first time? screen, select
Yes, I will set up my printer's wireless network. Then, click Next.
Creating the infrastructure network
1
2
3
Check wheter the USB cable is connected to the machine.
Turn on your computer, access point, and machine.
Insert the supplied software CD into your CD-ROM drive.
If the installation window does not appear, click Start > All programs >
Accessories > Run.
X:\Setup.exe replacing “X” with the letter, which represents your CDROM drive and click OK.
4
Review and accept the installation agreements in the installation
window. Then, click Next.
If your printer is already connected on the network, select No, my
printer is already connected to my network.
7
After searching, the window shows the wireless network devices. Select
the name (SSID) of the access point you want to use and click Next.
2. Using a Network-Connected Machine
156
Wireless network setup
If you cannot find the network name you want to choose, or if you want to
set the wireless configuration manually, click Advanced Setting.
• Enter the wireless Network Name: Enter the SSID of the access point
(SSID is case-sensitive).
8
If your printer supports Wi-Fi Direct and this function is disabled, its
corresponding screen will appears.
If you want to enable Wi-Fi Direct, check the checkbox, and click Next. If
not, click just Next.
• Operation Mode: Select Infrastructure.
• Authentication: Select an authentication type.
Open System: Authentication is not used, and encryption may or may
not be used, depending on the need for data security.
Shared Key: Authentication is used. A device that has a proper WEP key
can access the network.
WPA Personal or WPA2 Personal: Select this option to authenticate the
print server based on a WPA Pre-Shared Key. This uses a shared secret key
(generally called Pre Shared Key pass phrase), which is manually
configured on the access point and each of its clients.
• Encryption: Select the encryption (None, WEP64, WEP128, TKIP, AES,
TKIP AES).
• Network Password: Enter the encryption network password value.
• Confirm Network Password: Confirm the encryption network
password value.
• WEP Key Index: If you are using WEP Encryption, select the appropriate
WEP Key Index.
• Wi-Fi Direct option appears on the screen only if your printer supports
this feature.
• Can start to build Wi-Fi Direct by using Samsung Easy Printer Manager
(see "Setting up Wi-Fi Direct" on page 168).
The wireless network security window appears when the access point has
security settings.
• Wi-Fi Direct Name: The default Wi-Fi Direct Name is the model name
and the maximum length is 23 characters.
• Password setting is the numeric string, and the size is 8 ~ 64 characters.
Enter the Network Password of the access point (or router).
2. Using a Network-Connected Machine
157
Wireless network setup
9
10
When the wireless network set up is completed, disconnect the USB
cable between the computer and machine. Click Next.
Follow the instructions in the installation window.
Creating the infrastructure network
1
2
Turn on your computer, access point, and machine.
Insert the supplied software CD into your CD-ROM drive.
Access point without a USB cable (recommended)
Items to prepare
•
WiFi-enabled PC running Windows 7 or higher and an access point (router)
•
Software CD that was provided with your machine
•
A machine installed with a wireless network interface
If the installation window does not appear, click Start > All programs >
Accessories > Run.
X:\Setup.exe replacing “X” with the letter, which represents your CDROM drive and click OK.
While setting the wireless network, the machine uses PC's wireless LAN. You
might not be able to connect to the Internet.
3
Review and accept the installation agreements in the installation
window. Then, click Next.
2. Using a Network-Connected Machine
158
Wireless network setup
4
Select Wireless network connection on the Printer Connection Type
screen. Then, click Next.
5
On the Are you setting up your printer for the first time? screen, select
Yes, I will set up my printer's wireless network. Then, click Next.
6
Select Using a direct wireless connection on the Select the Wireless
Setup Method screen. Then, click Next.
If your printer is already connected on the network, select No, my
printer is already connected to my network.
2. Using a Network-Connected Machine
159
Wireless network setup
16
Setup using Mac
Even if your computer is running Windows 7 or higher, you cannot use this
feature if your PC does not support wireless network. Set the wireless
network using a USB cable (see "Access point via USB cable" on page 155).
Access point via USB cable
If below screen appears, press the
panel within 2 minutes.
7
8
(WPS) button from the control
Items to prepare
•
Access point
•
Network-connected printer
•
Software CD that was provided with your machine
•
A machine installed with a wireless network interface
•
USB cable
1
Make sure that the machine is connected to your computer andpowered
on.
2
Insert the supplied software CD into your CD-ROM drive.
When the wireless network set up is completed, click Next.
Follow the instructions in the installation window.
2. Using a Network-Connected Machine
160
Wireless network setup
3
Double-click the CD-ROM icon that appears on your Mac desktop.
•
4
5
6
7
8
For Mac OS X 10.8, double-click the CD-ROM that appears on Finder.
10
Select Configuration of Wireless network on the Printer Connection
Type and click Continue.
Double-click the MAC_Installer folder > Installer OS X icon.
Click Continue.
Read the license agreement and click Continue.
Click Agree to agree to the license agreement.
Click Install. All components necessary for machine operations will be
installed.
If you click Customize, you can choose individual components to install.
9
Enter the password and click OK.
2. Using a Network-Connected Machine
161
Wireless network setup
11
If Wireless Settings screen appears, select Using a USB cable and click
Next.
12
After searching, the window shows the wireless network devices. Select
the name (SSID) of the access point you want to use and click Next.
If the screen does not appear, go to step 15.
When you set the wireless configuration manually, click Advanced Setting.
• Enter the wireless Network Name: Enter the SSID of the access point
(SSID is case-sensitive).
• Operation Mode: Select Infrastructure.
• Authentication: Select an authentication type.
Open System: Authentication is not used, and encryption may or may
not be used, depending on the need for data security.
Shared Key: Authentication is used. A device that has a proper WEP key
can access the network.
WPA Personal or WPA2 Personal: Select this option to authenticate the
print server based on the WPA Pre-Shared Key. This uses a shared secret
key (generally called Pre Shared Key pass phrase) that is manually
configured on the access point and each of its clients.
• Encryption: Select the encryption. (None, WEP64, WEP128, TKIP, AES,
TKIP, AES)
• Network Password: Enter the encryption network password value.
• Confirm Network Password: Confirm the encryption network
password value.
• WEP Key Index: If you are using WEP Encryption, select the appropriate
WEP Key Index.
The wireless network security window appears when the access point has
security enabled.
Enter the Network Password of the access point (or router).
2. Using a Network-Connected Machine
162
Wireless network setup
13
The window showing the wireless network setting appears. Check the
settings and click Next.
• Wi-Fi Direct option appears on the screen only if your printer supports
this feature.
1
Make sure that the machine is connected to your computer andpowered
on.
2
Insert the supplied software CD into your CD-ROM drive.
3
Double-click the CD-ROM icon that appears on your Mac desktop.
• Can start to build Wi-Fi Direct by using Samsung Easy Printer Manager
(see "Setting up Wi-Fi Direct" on page 168).
• Wi-Fi Direct Name: The default Wi-Fi Direct Name is the model name
and the maximum length is 22 characters.
• Password setting is the numeric string, and the size is 8 ~ 64 characters.
14
15
When the wireless network settings are completed, disconnect the USB
cable between the computer and machine. Click Next.
Access point without a USB cable (recommended)
Items to prepare
•
•
The Wireless Network Setting Complete window appears. Click Next.
WiFi-enabled Mac running Mac OS 10.7 or higher and an access point
(router)
•
Software CD that was provided with your machine
•
A machine installed with a wireless network interface
4
5
6
7
8
For Mac OS X 10.8, double-click the CD-ROM that appears on Finder.
Double-click the MAC_Installer folder > Installer OS X icon.
Click Continue.
Read the license agreement and click Continue.
Click Agree to agree to the license agreement.
Click Install. All components necessary for machine operations will be
installed.
If you click Customize, you can choose individual components to install.
9
Enter the password and click OK.
2. Using a Network-Connected Machine
163
Wireless network setup
10
Select Configuration of Wireless network on the Printer Connection
Type and click Continue.
11
If Wireless Settings screen appears, select Using a direct wireless
connection and click Next.
If the screen does not appear, go to step 13.
2. Using a Network-Connected Machine
164
Wireless network setup
17
If below screen appears, press the
Using a network cable
(WPS) button from the control panel
within 2 minutes.
Machines that do not support the network port will not be able to use this
feature (see "Rear view" on page 22).
Your machine is a network compatible machine. To enable your machine to
work with your network, you will need to perform some configuration
procedures.
• After completing the wireless network connection, you need to install a
machine driver to print from an application (see "Installing driver over
the network" on page 140).
• See your network administrator, or the person that set up your wireless
network, for information about your network configuration.
Items to prepare
12
13
When the wireless network set up is completed, click Next.
•
Access point
•
Network-connected computer
•
Software CD that was provided with your machine
•
A machine installed with a wireless network interface
•
Network cable
After the installation is finished, click Close.
2. Using a Network-Connected Machine
165
Wireless network setup
Printing a network configuration report
Using SyncThru™ Web Service
You can identify the network settings of your machine by printing a network
configuration report.
Before starting wireless parameter configuration, check the cable connection
status.
See "Printing a network configuration report" on page 137.
IP setting using SetIP Program (Windows)
1
Check whether or not the network cable is connected to the machine. If
not, connect the machine with a standard network cable.
2
Start a web browser such as Internet Explorer, Safari, or Firefox and enter
your machine’s new IP address in the browser window.
This program is used to manually set the network IP address of your machine
using its MAC address to communicate with the machine. The MAC address is
the hardware serial number of the network interface and can be found in the
Network Configuration Report.
See "Setting IP address" on page 137.
Configuring the machine’s wireless network
Before starting you will need to know the network name (SSID) of your wireless
network and the Network Password if it is encrypted. This information was set
when the access point (or wireless router) was installed. If you do not know
about your wireless environment, please ask the person who set up your
network.
For example,
3
4
Click Login on the upper right of the SyncThru™ Web Service website.
Type in the ID and Password then click Login.
•
ID: admin
•
Password: sec00000
5
When the SyncThru™ Web Service window opens, click Network
Settings.
6
Click Wireless > Wizard.
To configure wireless parameters, you can use SyncThru™ Web Service.
Wizard will help you setup the wireless network configuration. However, if
you want to set the wireless network directly, select Custom.
2. Using a Network-Connected Machine
166
Wireless network setup
7
Select the one Network Name(SSID) in the list.
•
SSID: SSID (Service Set Identifier) is a name that identifies a wireless
network, access points, and wireless devices attempting to connect
to a specific wireless network must use the same SSID. The SSID is
case sensitive.
•
Operation Mode: Operation Mode refers to the type of wireless
connections (see "Wireless network name and Network Password"
on page 148).
-
10
Insert the supplied CD into the CD-ROM drive and proceed to install the
software following the directions on the screen. When the "Connect
Printer" screen appears, select the Network (Ethernet/Wireless)
connection.
Infrastructure: Allows wireless devices to communicate with
each other through an access point.
If your network’s Operation Mode is Infrastructure, select the SSID of the
access point. Note that “portthru” is the default SSID of your machine.
8
Click Next.
If the wireless security setting window appears, enter the registered
password (Network Password) and click Next.
9
The confirmation window appears, please check your wireless setup. If
the setup is right, click Apply.
Disconnect the network cable (standard or network). Your machine should
then start communicating wirelessly with the network.
2. Using a Network-Connected Machine
167
Wireless network setup
18
19
Turning the Wi-Fi network on/off
If your machine has a display, you can also turn on/off the Wi-Fi from the
machine’s control panel using the Network menu.
1
Check whether the network cable is connected to the machine. If not,
connect the machine with a standard network cable.
2
Start a web browser such as Internet Explorer, Safari, or Firefox and enter
your machine’s new IP address in the browser window.
Setting the Wi-Fi Direct for mobile printing
With Wi-Fi Direct, you can connect your printer to a Wi-Fi Direct network while
concurrently connecting to an access point, You can also use a wired network
and a Wi-Fi Direct network simultaneously so multiple users can access and print
documents both from Wi-Fi Direct and from a wired network.
• You cannot connect to the Internet through the mobile device in use WiFi Direct.
• The supported protocol list may differ from your model, Wi-Fi Direct
networks do NOT support IPv6, network filtering, IPSec, WINS, and SLP
services.
For example,
3
4
Click Login on the upper right of the SyncThru™ Web Service website.
Type in the ID and Password, then click Login.
•
ID: admin
•
Password: sec00000
5
When the SyncThru™ Web Service window opens, click Network
Settings.
6
Click Wireless > Custom.
• Up to four mobile devices can connect to Wi-Fi Direct at one time.
Setting up Wi-Fi Direct
You can enable Wi-Fi Direct feature by one of the following methods.
From the USB cable-connected computer(recommended)
•
After the driver installation is complete, Samsung Easy Printer Manager can
be set and changes in the Wi-Fi Direct can be made.
You can also turn the Wi-Fi network on/off.
2. Using a Network-Connected Machine
168
Wireless network setup
From the machine (Machines with a display screen)
Samsung Easy Printer Manager is Available for Windowsand Mac OS users
only.
-
From the Start menu, select Programs or All Programs > Samsung
Printers > Samsung Easy Printer Manager > Device Settings >
Network.
▪
Wi-Fi Direct On/Off: Select On to enable.
▪
Device Name: Enter the printer’s name for searching for your
printer on a wireless network. By default, the device name is the
model name.
▪
IP Address: Enter the IP address of the printer. This IP address is
used only for the local network and not for the infrastructure wired
or wireless network. We recommend using the default local IP
address (the default local IP address of the printer for Wi-Fi Direct is
192.168.3.1 )
▪
▪
Group Owner: Activate this option to assign the printer the Wi-Fi
Direct group’s owner. The Group Owner acts similar to a wireless
access point. We recommend activating this option.
•
Select Network > Wireless > Wi-Fi Direct from the control panel.
•
Enable Wi-Fi Direct.
From the network-connected computer
If your printer is using a network cable or a wireless access point, you can enable
and configure Wi-Fi Direct from SyncThru™ Web Service.
•
Access SyncThru™ Web Service, select Settings > Network Settings >
Wireless > Wi-Fi Direct.
•
Enable or disable Wi-Fi Direct and set other options.
• For Linux OS users,
- Print an IP network configuration report to check the output (see
"Printing a network configuration report" on page 137).
- Access SyncThru Web Service, select Settings > Network Settings
> Wireless > Wi-Fi Direct.
- Enable or disable Wi-Fi Direct.
Network Password: If your printer is a Group Owner, a Network
Password is required for other mobile devices to connect to your
printer. You can configure a Network Password yourself, or can
remember the given Network Password that is randomly generated
by default.
2. Using a Network-Connected Machine
169
Wireless network setup
Setting up the mobile device
20
Troubleshooting
•
After setting up Wi-Fi Direct from the printer, refer to the user manual of the
mobile device you are using to set its Wi-Fi Direct.
•
After setting up Wi-Fi Direct, you need to download the mobile printing
application (For example: Samsung Mobile printer) to print from your
smartphone.
Problems during setup or driver installation
Printers Not Found
•
• When you have found the printer you want to connect to from your
mobile device, select the printer and the printer's LED will blink. Press the
WPS button on the printer and it will be connected to your mobile
device.
Your machine may not be turned on. Turn on your computer and the
machine.
•
USB cable is not connected between your computer and machine. Connect
the machine to your computer using the USB cable.
• If your mobile device does not support WPS, you need to enter the
"Network Password" of a printer instead of pushing the WPS button.
•
The machine does not support wireless networking. Check the machine's
user's guide included on the software CD supplied with your machine and
prepare a wireless network machine.
Connecting Failure - SSID Not Found
•
The machine is unable to find the network name (SSID) you have selected or
entered. Check the network name (SSID) on your access point and try
connecting again.
•
Your access point is not turned on. Turn on your access point.
2. Using a Network-Connected Machine
170
Wireless network setup
Connecting Failure - Invalid Security
▪
•
Then the machine’s network information should be as below:
Security is not configured correctly. Check the configured security on your
access point and machine.
Connecting Failure - General Connection Error
•
Your computer is not receiving a signal from your machine. Check the USB
cable and your machine’s power.
Connecting Failure - Connected Wired Network
•
Subnet Mask: 255.255.0.0
▪
IP address: 169.254.133.43
▪
Subnet Mask: 255.255.0.0 (Use the computer’s subnet mask.)
▪
Gateway: 169.254.133.1
Other problems
If problems occur while using the machine on a network, check the following:
Your machine is connected with a wired network cable. Remove the wired
network cable from your machine.
For information on the access point (or wireless router), refer to its own
user's guide.
PC Connection Error
•
The configured network address is unable to connect between your
computer and machine.
•
Your computer, access point (or wireless router), or machine may not be
turned on.
-
•
Check the wireless reception around the machine. If the router is far from
the machine or there is an obstacle, you might have difficulty receiving the
signal.
•
Cycle the power for the access point (or wireless router), machine, and
computer. Sometimes cycling the power can recover network
communication.
For a DHCP network environment
The receives the IP address automatically (DHCP) when computer is
configured to DHCP.
-
For a Static network environment
The machine uses the static address when the computer is configured
to static address.
For example,
If the computer’s network information is as shown below:
▪
IP address: 169.254.133.42
2. Using a Network-Connected Machine
171
Wireless network setup
•
Check whether firewall software (V3 or Norton) is blocking the
communication.
•
If the computer and the machine are connected on the same network and it
cannot be found when searching, firewall software might be blocking the
communication. Refer to the user's guide for the software to turn it off and
try searching for the machine again.
•
Check whether the machine's IP address is allocated correctly. You can
check the IP address by printing the network configuration report.
•
Check whether the access point (or wireless router) has a configured
security (password). If it has a password, refer to the access point (or wireless
router) administrator.
•
Check the machine's IP address. Reinstall the machine driver and change the
settings to connect to the machine on the network. Due to the
characteristics of DHCP, the allocated IP address could change if the
machine is not used for a long time or if the access point has been reset.
Register the product's MAC address when you confogure the DHCP server
on the access point (or wireless router). Then you can always use the IP
address that is set with the MAC address. You can identify the Mac address
of your machine by printing a network configuration report (see "Printing a
network configuration report" on page 137).
•
Check the wireless environment. You might not be able to connect to the
network in the infrastructure environment where you need to type in a
user's information before connecting to the access point (or wireless router).
•
This machine only supports IEEE 802.11 b/g/n and Wi-Fi. Other wireless
communication types (e.g., Bluetooth) are not supported.
•
The machine is within the range of the wireless network.
The machine is located away from obstacles that could block the wireless
signal.
Remove any large metal objects between the access point (or wireless
router) and the machine.
Make sure the machine and wireless access point (or wireless router) are not
separated by poles, walls, or support columns containing metal or concrete.
•
The machine is located away from other electronic devices that may
interfere with the wireless signal.
Many devices can interfere with the wireless signal, including a microwave
oven and some Bluetooth devices.
•
Whenever the configuration of your access point (or wireless router)
changes, you must do the product's wireless network setup again.
•
If Wi-Fi Direct is ON, this machine only supports IEEE 802.11 b/g.
•
If the access point is set to work with the 802.11n standard only, it may
notconnect to your machine.
2. Using a Network-Connected Machine
172
Samsung Mobile Print
21
23
What is Samsung Mobile Print?
Samsung Mobile Print is a free application that enables users to print photos,
documents, and web pages directly from your smartphone or tablet. Samsung
Mobile Print is not only compatible with your Android and iOS smart phones
but also with your iPod Touch and tablet PC. It connects your mobile device to a
network connected Samsung printer or to a wireless printer through a Wi-Fi
access point. Installing a new driver or configuring network settings isn’t
necessary – just simply install the Samsung Mobile Print application, and it will
automatically detect compatible Samsung printers. Besides printing photos,
web pages, and PDFs, scanning is also supported. If you have Samsung
multifunction printer, scan any document into a JPG, PDF, or PNG format for
quick and easy viewing on your mobile device.
Supported Mobile OS
•
Android OS 2.1 or higher
•
iOS 4.0 or higher
24
Supported devices
•
iOS 4.0 or higher: iPod Touch, iPhone, iPad
•
Android 2.3 or higher: Galaxy series and Android mobile devices
22
Downloading Samsung Mobile Print
To download Samsung Mobile Print, go to the application store (Samsung
Apps, Play Store, App Store) on your mobile device, and just search for
“Samsung Mobile Print.” You can also visit iTunes for Apple devices on your
computer.
2. Using a Network-Connected Machine
173
Using the NFC feature
The NFC(Near Field Communication) printer allows you to directly print/scan
from your cell phone just by holding your cell phone over the NFC tag on your
printer. It does not require installing print driver or connecting to an access
point. You just need NFC supported cell phone. In order to use this feature,
Samsung Mobile Print app needs to be installed on your cell phone.
• Depending on the material of the cell phone cover, NFC recognition may
not work properly.
• Depending on the cell phone you are using, the tranmission speed may
differ.
26
Printing
1
Check that NFC and Wi-Fi Direct features are enabled on your cell phone
and Wi-Fi Direct feature is enabled on your printer (see "Setting up Wi-Fi
Direct" on page 168).
2
Tag the NFC antenna on your cell phone (usually located on the back of
the cell phone) over the NFC tag(
) on your printer.
Wait few seconds for Samsung Mobile Print app to start.
25
Requirements
•
NFC and Wi-Fi Direct enabled, Mobile Print app installed cell phone with
Android OS 4.0 or higher.
Only Android OS 4.1 or higher will automatically enable the Wi-Fi Direct
feature on your cell phone when you enable the NFC feature. We
recommend you to upgrade your cell phone to Android OS 4.1 or higher to
use the NFC feature.
•
Wi-Fi Direct feature enabled printer. Wi-Fi Direct feature is enabled by
default.
2. Using a Network-Connected Machine
174
Using the NFC feature
• For some cell phones, NFC antenna might not be located at the back of
the cell phone. Check the location of the NFC antenna on your cell phone
before tagging.
• For some cell phones, NFC antenna might not be located at the back of
the cell phone. Check the location of the NFC antenna on your cell phone
before tagging.
• If error message about changed PIN number appears, enter a changed
PIN number and press OK. Follow the instruction on the app screen to
update the PIN number.
• If error message about changed PIN number appears, enter a changed
PIN number and press OK. Follow the instruction on the app screen to
update the PIN number.
• If you do not have Samsung Mobile Print app installed on your cell
phone, it automatically connects to Samsung Mobile Print app
download page. Download the app and try again.
3
The printer starts printing.
Select the content you want to print.
If neccessary, change the print option by pressing the
4
5
.
Tag the NFC antenna on your cell phone(usually located on the back of
the cell phone) over the NFC tag(
) on your printer.
Wait few seconds for the cell phone to connect to the printer.
2. Using a Network-Connected Machine
175
Using the NFC feature
27
• For some cell phones, NFC antenna might not be located at the back of
the cell phone. Check the location of the NFC antenna on your cell phone
before tagging.
Scanning
1
Check that NFC and Wi-Fi Direct enabled features are on your cell phone
and Wi-Fi Direct feature is enabled on your printer (see "Setting up Wi-Fi
Direct" on page 168).
• If error message about changed PIN number appears, enter a changed
PIN number and press OK. Follow the instruction on the app screen to
update the PIN number.
2
Tag the NFC antenna on your cell phone(usually located on the back of
the cell phone) over the NFC tag(
) on your printer.
• If you do not have Samsung Mobile Print app installed on your cell
phone, it automatically connects to Samsung Mobile Print app
download page. Download the app and try again.
Wait few seconds for Samsung Mobile Print app to start.
3
4
Select scan mode.
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
If neccessary, change the scan option by pressing the
.
2. Using a Network-Connected Machine
176
Using the NFC feature
5
Tag the NFC antenna on your cell phone(usually located on the back of
the cell phone) over the NFC tag(
) on your printer.
Wait few seconds for the cell phone to connect to the printer.
• For some cell phones, NFC antenna might not be located at the back of
the cell phone. Check the location of the NFC antenna on your cell phone
before tagging.
• If error message about changed PIN number appears, enter a changed
PIN number and press OK. Follow the instruction on the app screen to
update the PIN number.
6
The printer starts scanning the content.
The scanned data is saved on your cell phone.
If you want to continue scanning, follow the instruction on the app screen.
2. Using a Network-Connected Machine
177
3. Useful Setting Menus
This chapter explains how to browse the current status of your machine, and the method of setting for advanced
machine setup.
• Before you begin reading a chapter
179
• Copy menu
180
• Fax menu
182
• System setup
185
Before you begin reading a chapter
This chapter explains all the features available for this series' models to help users easily understand the features.You can check the features available for each model
in the Basic Guide (see "Menu overview" on page 31).The following are tips for using this chapter
•
The control panel provides access to various menus to set up the machine or use the machine’s functions. These menus can be accessed by pressing
•
Some menus may not appear on the display depending on options or models. If so, it is not applicable to your machine.
•
For models that do not have the
•
Some menu names may differ from your machine depending on its options or the models.
(Menu).
(Menu) on the control panel, this feature is not applicable (see "Control panel overview" on page 23).
3. Useful Setting Menus
179
Copy menu
1
Item
Copy feature
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
Darkness
Adjusts the brightness level to make a copy that is
easier to read, when the original contains faint
markings and dark images (see "Darkness" on page 57)
Original Type
Improves the copy quality by selecting the document
type for the current copy job (see "Original" on page 57)
Set the machine to sort the copy job. For example, if you
make 2 copies of a 3 page original, one complete 3 page
document will print followed by a second complete
document.
To change the menu options:
•
Press
(copy) >
•
Or press Setup > Machine Setup > Default Setting > Copy Default.
•
Or press Copy > select the menu item you want.
(Menu) > Copy Feature on the control panel.
Item
Original Size
Description
Description
• On: Prints output in sets to match the sequence of
originals.
Collation
Sets the image size.
• Off: Prints output sorted into stacks of individual
pages.
Reduces or enlarges the size of a copied image (see
"Reduced or enlarged copy" on page 58).
Reduce/Enlarge
If the machine is set Eco mode, reduce and
enlarge features are not available.
Layout
Adjust the layout format such as 2/4-up and ID copy.
3. Useful Setting Menus
180
Copy menu
2
Item
Description
Copy Setup
Reduces the size of the original images and prints 2 or 4
pages onto one sheet of paper.
2
3
4
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
2-up or 4-up
1
2
1
To change the menu options:
This copy feature is available only when you
load originals into the document feeder.
Prints an image without its background. This copy
feature removes the background color and can be
helpful when copying an original containing color in
the background, such as a newspaper or a catalog.
Adjust Bkgd
Press
(copy) >
Item
Change Default
(Menu) > Copy Setup on the control panel.
Description
Resets the value or setting to the printer’s out-of-box
state.
• Off: Does not use this feature.
• Auto: Optimizes the background.
• Enhance Lev.1~2: The higher the number is, the
more vivid the background is.
• Erase Lev.1~4: The higher the number is, the lighter
the background is.
3. Useful Setting Menus
181
Fax menu
3
Item
Fax Feature
Description
Sends a fax to multiple destinations (see "Sending a fax
to multiple destinations" on page 63).
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
Multi Send
You cannot send a color fax using this feature.
Sets your machine to send a fax at a later time when you
will not be present (see "Delaying a fax transmission" on
page 226).
To change the menu options:
•
Press
(fax) >
(Menu)> Fax Feature on the control panel.
•
Or press Setup > Machine Setup > Default Setting > Fax Default.
•
Or press Fax > select the menu item you want.
Item
You cannot send a color fax using this feature.
Description
Darkness
Adjusts the brightness level to scan an original that is
easier to read, when the original contains faint
markings and dark images (see "Darkness" on page 65).
Resolution
The default document settings procedure good results
when using typical text-based originals. However, if you
send originals that are of poor quality, or contain
photographs, you can adjust the resolution to produce
a higher quality fax (see "Resolution" on page 64).
Original Size
Delay Send
Sets the image size.
Priority Send
Send Forward/
Rcv.Forward
Scans the original into memory and immediately
transmits it when the current operation is finished.
Priority transmission will interrupt a sending to multiple
destinations between stations (example, when the
transmission to station A ends, before transmission to
station B begins) or between redial attempts (see
"Sending a priority fax" on page 228).
Forwards the received or sent fax to other destination
by a fax or PC. If you are out of office but have to receive
the fax, this feature may be useful.
• See "Forwarding a sent fax to another destination"
on page 228.
• See "Forwarding a received fax" on page 229.
3. Useful Setting Menus
182
Fax menu
Item
Description
Secure Receive
Add Page
Cancel Job
Stores the received fax in memory without printing out.
To print received documents, you need to enter the
password. You can prevent your received faxes from
being accessed by unauthorized people (see "Receiving
in secure receiving mode" on page 233).
Item
Description
Redial Times
Sets the number of redial attempts. If you enter 0, the
machine will not redial.
Redial Term
Sets the time interval before automatic redialling.
Adds additional documents to a reserved delay fax job
(see "Adding documents to a reserved fax" on page
227).
Prefix Dial
Sets a prefix of up to five digits. This number dials
before any automatic dial number is started. It is useful
for accessing a PABX exchange.
Cancels the delayed fax job which is saved in memory
(see "Canceling a reserved fax job" on page 227).
ECM Mode
Sends faxes using error correction mode (ECM) to
makes sure the faxes are sent smoothly without any
error. It may take more time.
Fax Confirm.
Sets the machine to print a report whether a fax
transmission was successfully completed or not. If you
select On-Error, the machine prints a report only when
a transmission is not successful.
Image TCR
Prints a transmission report with a minimized image of
the first page of the fax sent.
Dial Mode
Sets the dialing mode to either tone or pulse. This
setting may not be available depending on your
country.
4
Sending setup
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
To change the menu options:
•
Press
(fax) >
(Menu) > Fax Setup > Sending on the control panel.
•
Or press Setup > Machine Setup > Default Setting > Fax Default.
3. Useful Setting Menus
183
Fax menu
5
Item
Receiving setup
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
Auto Reduction
Automatically reduces an incoming fax page to fit the
size of the paper loaded in the machine.
Discard Size
Discards a specific length from the end of the received
fax.
Junk Fax Setup
Blocks any unwanted faxes that you stored in the
memory as junk fax numbers. This setting may not be
available depending on your country.
DRPD Mode
Enables a user to use a single telephone line to answer
several different telephone numbers. You can set the
machine to recognize different ring patterns for each
number. This setting may not be available depending
on your country (see "Receiving faxes using DRPD
mode" on page 232).
To change the menu options:
•
Press
(fax) >
•
Or press Setup > Machine Setup > Default Setting > Fax Default.
Item
(Menu) > Fax Setup > Receiving on the control panel.
Description
Receive Mode
Selects the default fax receiving mode.
Ring To Answer
Specifies the number of times the machine rings before
answering an incoming call.
Stamp RCV Name
Automatically prints the page number, and the date
and time of reception at the bottom of each page of a
received fax.
Rcv Start Code
Initiates fax reception from an extension phone
plugged into the EXT socket on the back of the
machine. If you pick up the extension phone and hear
fax tones, enter the code. It is preset to *9* at the
factory.
Description
3. Useful Setting Menus
184
System setup
6
Item
Machine setup
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
Select Form
Form overlay is images stored on the printer’s mass
storage device (HDD) as a special file format that can be
printed in layers on any document.
HDD Spooling
When On, stores documents on the mass storage device
(HDD) for network printing.
Language
Sets the language of the text that appears on the control
panel display.
Default Mode
Sets the machine’s default mode among fax mode, copy
mode, or scan mode.
Default Paper Size
You can set the default paper size to use.
To change the menu options:
•
Press
•
Or press Setup > Machine Setup > Initial Setup.
Item
(Menu) > System Setup > Machine Setup on the control panel.
Sets how long the machine waits before going to power
save mode.
Description
Machine ID
Sets the machine ID which will be printed at the top of
each fax page that you send.
Fax Number
Sets the fax number which will be printed at the top of
each fax page that you send.
Date & Time
Sets the date and time.
Power Save
Selects the format for displaying time between 12 hr. and
24 hr.
• Off: Prints in normal mode.
Form Menu
• Single Form: Prints all page using the first form.
• Double Form: Prints the front page using the first
form and the back page using the second form.
When the machine does not receive data for an extended
period of time, power consumption is automatically
lowered.
Sets how long the machine’s scanner part waits before
going to power save mode.
Scan PWR Save
Clock Mode
Description
System Timeout
When the scanner does not receive data for an extended
period of time, power consumption is automatically
lowered.
Sets the time that the machine remembers previously
used copy settings. After the timeout, the machine
restores the default copy settings.
3. Useful Setting Menus
185
System setup
Item
Job Timeout
Description
Sets the length of time the printer waits before printing
the last page of a print job that does not end with a
command to print the page.
You can set the condition to wake up from power-save
mode. Set the item on.
Wakeup Event
• Button Press: When you press any button except
power button, the machine wake up from the power
save mode.
• Scanner: When you insert paper in the document
feeder, the machine wake up from the power save
mode.
Item
Auto CR
Allows you to append the required carriage return to
each line feed, which is useful for DOS users.
Firmware Version
Shows the product’s firmware version.
AutoComplete
Provides suggestions while you type an email address or
fax number. This enables you to find and select the data
without typing it in completely.
• Tray Chaining
• Auto Tray Switch
• Printer: When you open or close the paper tray, the
machine wake up from the power save mode.
• Off: If a paper mismatch occurs, the machine waits
until you insert the correct paper.
• On: If a paper mismatch occurs, an error message will
display. The machine waits for about 30 second, then
automatically clear the message and continue
printing.
• Altitude Adj.
• Altitude
Adjustment
Optimize print quality according to the machine’s
altitude.
Determine whether or not the machine continues
printing when it detects the paper does not match. For
example, if both tray 1 and tray 2 are filled with the same
size paper, the machine automatically prints from tray 2
after the tray 1 runs out of paper.
This option does not appear if you selected Auto
for Paper Source from printer driver.
Determine whether or not the machine continues
printing when it detects the paper does not match the
paper settings.
Auto Continue
Description
Paper Substit.
Paper Substitution
Paper Mismatch
Automatically substitutes the printer driver’s paper size
to prevent the paper mismatch between Letter and A4.
For example, if you have A4 paper in the tray but you set
the paper size to Letter in the printer driver, the machine
prints on A4 paper and vice versa.
Determine whether to disregard the paper mismatch
error or not. Select Off, then the machine does not stop
printing even if the paper mismatches.
3. Useful Setting Menus
186
System setup
Item
PrintBlankPage
Multi-Bin
Description
Item
Import Setting
Imports data stored on a USB memory stick to the
machine.
Export Setting
Exports data stored on a USB memory stick to the
machine.
Toner Save
Activating this mode extends the life of your toner
cartridge and reduces your cost per page beyond what
one would experience in the normal mode, but it reduces
print quality.
Quiet Mode
• Clean Fuser: Cleans the fuser by printing a sheet.
You can reduce the printing noise by turning this menu
on. However, the printing speed and quality may be
declined.
• CLR Empty Msg.: This option appears only when
toner cartridge is empty.
Allows you to save print resources and enables ecofriendly printing.
The printer detects the printing data from computer
whether a page is empty or not. You can set to print or
skip the blank page.
• Mode: Selects the multi-bin mode you want to use.
• Default Bin: Selects the bin to use as a default.
Default Source
Sets the tray to use as a default.
Address Book
Views or prints the phone book or email address list.
• Clean Drum: Cleans the OPC drum of the cartridge by
printing a sheet.
• Supplies Info.: Allows you to check how many pages
are printed and how much toner is left in the cartridge.
Maintenance
Description
• TonerLow Alert: If toner in the cartridge has run out,
a message informing the user to change the toner
cartridge appears. You can set the option for this
message to appear or not.
• Paper Stacking: If you use a machine in a humid area,
or you are using the damp print media caused by a
high humidity, the print-outs on the output tray may
be curled and may not be stacked properly. In this
case, you can set the machine to use this function to
let print-outs stacked firmly. But, using this function
will make the print speed slow.
• Default Mode: Select whether to turn the Eco mode
on or off.
Eco Settings
On force (On-Forced): Sets the Eco mode on with
password. If a user wants to turn the Eco mode
on/off, the user needs to enter the password.
• Select Template (Select Temp.): Selects the eco
template set from the SyncThru™ Web Service.
Clear Setting
Restores the machine’s factory default settings.
3. Useful Setting Menus
187
System setup
7
8
Paper setup
Sound / Volume
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
To change the menu options:
To change the menu options:
•
Press
•
Press
•
Or press Setup > Machine Setup > Paper Setup.
•
Or press Setup > Machine Setup > Initial Setup > Sound/Volume.
(Menu) > System Setup > Paper Setup on the control panel.
Item
Description
Paper Size
Sets the paper size as A4, Letter, or other paper sizes,
according to your requirements.
Paper Type
Chooses the type of the paper for each tray.
Paper Source
Selects from which tray the paper is used.
Margin
Sets the margins for the document.
Tray Confirm
Activates the tray confirmation message. If you open and
close a tray, a window asking you whether to set the
paper size and type for the tray just opened appears.
(Menu) > System Setup > Sound/Volume on the control panel.
Item
Description
Key Sound
Turns the key sound on or off. With this option set to on,
a tone sounds each time a key is pressed.
Alarm Sound
Turns the alarm sound on or off. With this option set to
on, an alarm tone sounds when an error occurs or fax
communication ends.
3. Useful Setting Menus
188
System setup
9
Item
Description
Report
Turns on or off the sounds from the telephone line
through the speaker, such as a dial tone or a fax tone.
With this option set to Comm. which means the speaker
is on until the remote machine answers.
Speaker
You can adjust the volume level using On Hook
Dial. You can adjust the speaker volume only
when the telephone line is connected.
To change the menu options:
a Press
•
Press
•
Or press Setup > Machine Setup > Reports.
(fax) on the control panel.
b Press On Hook Dial. A dial tone sounds from
the speaker.
c Press the arrows until you hear the volume you
want.
d Press On Hook Dial to save the change and
return to ready mode.
Ringer
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
Adjusts the ringer volume. For the ringer volume, you can
select off, low, middle, and high level.
(Menu) > System Setup > Report on the control panel.
Item
Description
Menu Map
Prints the menu map which shows the layout and
current settings of this machine.
Configuration
Prints a report on the machine's overall
configuration.
Supplies Info.
Prints supplies’ information page.
Address Book
Prints all of the email addresses currently stored
in the machine’s memory.
Demo Page
Prints the demo page to check whether your
machine is printing properly or not.
3. Useful Setting Menus
189
System setup
10
Item
Description
Fax Confirm.
Prints a transmission report including the fax
number, the number of pages, the elapsed time
of the job, the communication mode, and the
communication results for fax job. You can set up
your machine to automatically print a
transmission confirmation report after each fax
job.
Fax Sent
Prints information on the faxes you have recently
sent.
Fax Received
Prints information on the faxes you have recently
received.
Schedule Jobs
Prints the document list currently stored for
delayed faxes along with the starting time and
type of each operation.
JunkFax
Network Conf.
Maintenance
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
To change the menu options:
•
Press
(Menu) > System Setup > Maintenance on the control panel.
•
Or press Setup > Machine Setup > Initial Setup.
Item
Description
CLR Empty Msg.
When toner cartridge is empty, this option appears. You
can clear the empty message.
Supplies Life
Shows the supply life indicators (see "Monitoring the
supplies life" on page 75.)
TonerLow Alert
Customizes the level to alert toner low or toner empty
(see "Setting the toner low alert" on page 76).
Serial Number
Shows the machine’s serial number. When you call for
service or register as a user on the Samsung website, you
can find this.
Prints the fax numbers specified as junk fax
numbers.
Prints information on your machine’s network
connection and configuration.
3. Useful Setting Menus
190
Network setup
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine (see "Menu overview" on
page 31).
•
Press
•
Or press Setup > Machine Setup > Network Setup.
Option
You can activate or deactivate the following protocols.
• Net. Activate: : You can set whether to use Ethernet
on or off.
• Http Activate: You can sets whether to use
SyncThru™ Web Service or not.
(Menu)> Network on the control panel,
Option
TCP/IP (IPv4)
• WINS: You can configure the WINS server.
WINS(Windows Internet Name Service) is used in the
Windows operating system.
Description
Selects the appropriate protocol and configure
parameters to use the network environment.
There are lots of parameters to be set. If you are
not sure, leave as is, or consult the network
administrator.
TCP/IP (IPv6)
Selects this option to use the network environment
through IPv6 (see "IPv6 configuration" on page 145).
Ethernet
Configure the network transmission speed.
802.1x
You can selects the user authentication for network
communication. For detailed information consult the
network administrator.
Wi-Fi
Selects this option to use the wireless network.
Description
Protocol Mgr.
• SNMP V1/V2: You have to enable this option to use
SNMP V1/V2 protocol. Administrator’s can use SNMP
to monitor and manage machines on the network.
• UPnP(SSDP): You have to enable this option to use
UPnP(SSDP) protocol.
Turn the power off and on after you change
above options.
3. Useful Setting Menus
191
Network setup
Option
Description
• MDNS: You have to enable this option to use MDNS
(Multicast Domain Name System) protocol.
• SetIP: You have to enable this option to use SetIP
protocol.
Protocol Mgr.
(continued.)
• SLP: You can configure SLP (Service Location
Protocol) settings. This protocol allows host
applications to find services in a local area network
without prior configuration.
Turn the power off and on after you change this
option.
Network Conf.
This list shows information on your machine’s network
connection and configuration.
Clear Setting
Reverts the network settings to the default values.
(Reboot required.)
3. Useful Setting Menus
192
4. Special Features
This chapter explains special copying, scanning, faxing, and printing features.
• Altitude adjustment
194
• Storing email address
195
• Entering various characters
197
• Setting up the fax address book
198
• Registering authorized users
202
• Printing features
203
• Scan features
216
• Fax features
225
• Using shared folder features
234
• Using memory/hard drive features
235
• The procedures in this chapter are mainly based on Windows 7.
• It may be necessary to press OK to navigate to lower-level menus for some models.
Altitude adjustment
Print quality is affected by atmospheric pressure, which is determined by the
height of the machine above sea level. The following information will guide you
on how to set your machine for the best print quality.
You can set the altitude value from Device Settings in Samsung Easy Printer
Manager program.
•
For Windows and Mac users, see "Device Settings" on page 246.
Before you set the altitude value, determine the altitude where you are.
5,000 m
(16,404 ft)
1
4,000 m
(13,123 ft)
2
3,000 m
(9,842 ft)
• If your machine is connected to the network, you can set the altitude via
SyncThru™ Web Service (see "Using SyncThru™ Web Service" on page
240).
• You can also set the altitude in System Setup option on the machine’s
display (see "Machine’s basic settings" on page 36).
3
2,000 m
(6,561 ft)
4
1,000 m
(3,280 ft)
5
0
1
2
3
4
5
High 4
High 3
High 2
High 1
Normal
4. Special Features
194
Storing email address
This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
You can set up address book with the email addresses you use frequently via
SyncThru™ Web Service and then easily and quickly enter email addresses by
entering the location numbers assigned to them in address book.
1
If you need to set SMB or FTP sever information, check SMB or FTP and set
the information.
6
7
8
Click Apply.
If you make a group, click Address Book > E-mail Group > Add Group.
Select the Speed No. and enter Group Name.
Storing on your machine
You can easily add individual address if you check Yes for Add individual(s)
after this group is created.
To scan and send an image as an email attachment, you need to set up email
address using SyncThru™ Web Service.
1
Access the SyncThru™ Web Service (see "Using SyncThru™ Web Service"
on page 240).
2
3
Click Login on the upper right of the SyncThru™ Web Service website.
9
Click Apply.
Type in the ID and Password then click Login.
•ID: admin
•Password: sec00000
4
5
Click Address Book > Individual > Add.
Select the Speed No. and enter e-mail address and fax number.
4. Special Features
195
Storing email address
2
Searching for an email address
Searching sequentially through memory
1
Select
(scan) >
(Address Book) > Search&Send > Select an
address group > All on the control panel.
Or select Setup > Machine Setup > Next > Address Book > Email >
View List > Individual or Group.
2
Search through the entire memory in index (numerical) order, and select
the name and address you want.
Searching with a particular first letter
1
2
Select
(scan) on the control panel.
3
4
Enter the first few letters of the name you want.
Press
(Address Book) > Search&Send > Select an address group >
ID on the control panel.
Press the arrows until the name and number you want appears.
4. Special Features
196
Entering various characters
As you perform various tasks, you may need to enter names and numbers. For
example, when you set up your machine, you enter your name or your
company’s name, and the fax number. When you store fax numbers or email
addresses in memory, you may also enter the corresponding names.
3
Entering alphanumeric characters
Press the button until the correct letter appears on the display. For example, to
enter the letter O, press 6, labeled with MNO. Each time you press 6, the display
shows a different letter, M, N, O, m, n, o and finally 6. To find the letter that you
want to enter, see "Keypad letters and numbers" on page 197.
• You can enter a space by pressing 1 twice.
• To delete the last digit or character, press the left/right or up/down arrow
button.
Key
Assigned numbers, letters, or characters
1
@/.’1
2
ABCabc2
3
DEFdef3
4
GHIghi4
5
JKLjkl5
6
MNOmno6
7
PQRSpqrs7
8
TUVtuv8
9
WXYZwxyz9
0
&+-,0
*
*%^_~!#$()[]
(These symbols are available when you type for network authentication.)
#
4
Keypad letters and numbers
#=|?":{}<>;
(These symbols are available when you type for network authentication.)
• Special character sets may differ from your machine depending on its
options or the models.
• Some of the follow key values may not appear depending on the job you
are doing.
4. Special Features
197
Setting up the fax address book
You can set up speed number with the fax numbers you use frequently via
SyncThru™ Web Service and then easily and quickly enter fax numbers by
entering the location numbers assigned to them in address book.
6
Using speed dial numbers
When you are prompted to enter a destination number while sending a fax,
enter the speed dial number at which you stored the number you want.
5
Registering a speed dial number
1
Select
(fax) >
the control panel.
(Address Book) > New&Edit > Speed Dial on
Or select Setup > Machine Setup > Next > Address Book > Phone
Book > View List > Individual >
• For a one-digit (0-9) speed dial number, press and hold the
corresponding digit button on the number keypad for more than 2
seconds.
• For a two- or three-digit speed dial number, press the first digit button(s)
and then hold down the last digit button for more than 2 seconds.
(options) > Add.
• You can print the address book list by selecting
2
Enter a speed dial number and press OK.
(fax) >
(Address Book) > Print.
If an entry is already stored in the number you choose, the display shows the
message to allow you to change it. To start over with another speed dial
number, press
3
4
5
(Back).
Enter the name you want and press OK.
Enter the fax number you want and press OK.
Press the
(Cancel or Stop/Clear) button to return to ready mode.
4. Special Features
198
Setting up the fax address book
7
8
Editing speed dial numbers
1
Select
(fax) >
the control panel.
(Address Book) > New&Edit > Speed Dial on
Registering a group dial number
1
Or select Setup > Machine Setup > Next > Address Book > Phone
Book > View List > Individual.
2
3
4
5
Enter the speed dial number you want to edit and press OK.
Select
(fax) >
the control panel.
(Address Book) > New&Edit > Group Dial on
Or select Setup > Machine Setup > Next >Address Book > Phone
Book > View List > Group>
2
(options) > Add.
Enter a group dial number and press OK.
Change the name and press OK.
If an entry is already stored in the number you choose, the display shows the
message to allow you to change it. To start over with another speed dial
number, press
(Back).
Change the fax number and press OK.
Press
(Cancel or Stop/Clear) to return to ready mode.
3
Search by entering the first few letters of the speed dial’s name to put in
the group.
4
5
6
7
Select the name and number you want and press OK.
8
Press
Select Yes when Add? appears.
Repeat step 3 to include other speed dial numbers into the group.
When you have finished, select No when Another No.? appears and
press OK.
(Cancel or Stop/Clear) to return to ready mode.
4. Special Features
199
Setting up the fax address book
9
10
Editing group dial numbers
1
Select
(fax) >
the control panel.
(Address Book) > New&Edit > Group Dial on
Or select Setup > Machine Setup > Next > Address Book > Phone
Book > View List > Group.
2
3
Enter the group dial number you want to edit and press OK.
Enter a new speed dial number to add and press OK, then Add? appears.
Enter a speed dial number stored in the group and press OK, Delete?
appears.
4
5
6
7
Searching address book for an entry
There are two ways to search for a number in memory. You can either scan from
A to Z sequentially, or you can search by entering the first letters of the name
associated with the number.
1
Select ct
(fax) >
(Address Book) > Search&Dial > Speed Dial
or Group Dial on the control panel.
2
3
Enter All or ID and press OK.
Press OK to add or delete the number.
Press the name and number or the keypad button labeled with the letter
you want to search.
For example, if you want to find the name “MOBILE,” press the 6 button,
which is labeled with “MNO.”
Repeat step 3 to add or delete more numbers.
Select No at the Another No.? and press OK.
Press
4
Press
(Cancel or Stop/Clear) to return to ready mode.
(Cancel or Stop/Clear) to return to ready mode.
4. Special Features
200
Setting up the fax address book
11
Printing address book
You can check your
1
2
Select ct
(Address Book) settings by printing a list.
(fax) >
(Address Book) > Print on the control panel.
Press OK.
The machine begins printing.
4. Special Features
201
Registering authorized users
This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
If you have connected your machine to a network and set up the network
parameters correctly, you can scan and send images over the network. To send
a scanned image through email or via network server safely, you must register
account information of authorized users to your local machine using SyncThru™
Web Service.
1
Access the SyncThru™ Web Service (see "Using SyncThru™ Web Service"
on page 240).
2
3
Click Login on the upper right of the SyncThru™ Web Service website.
8
Enter User Name, Login ID, Password, Confirm Password, E-mail
Address, and Fax Number.
You can easily add individual address if you check Yes for Add individual(s)
after this group is created.
9
Click Apply.
Type in the ID and Password then click Login.
•
ID: admin
•
Password: sec00000
4
5
Click Security > User Access Control > Authentication.
6
7
Click OK in the confirmation pop-up window.
Select Local Authentication in the Authentication Method, and click
Apply.
Click User Profile > Add.
4. Special Features
202
Printing features
• For basic printing features, refer to the Basic Guide (see "Basic printing"
on page 50).
If you want to change the settings for each print job, change it in Printing
Preferences.
• This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
13
Setting your machine as a default machine
12
Changing the default print settings
1
2
3
4
Click the Windows Start menu.
Select Control Panel > Devices and Printers.
Right-click on your machine.
1
2
3
4
Click the Windows Start menu.
Select Control Panel > Devices and Printers.
Select your machine.
Right-click your machine and select Set as Default Printer.
Select Printing preferences.
If Printing preferences has a ▶, you can select other printer drivers
connected to the selected printer.
If Printing preferences has a ▶, you can select other printer drivers
connected to the selected printer.
5
6
Change the settings on each tab.
Click OK.
4. Special Features
203
Printing features
14
Using advanced print features
1
Check the Print to file box in the Print window.
2
3
Click Print.
XPS printer driver: used to print XPS file format.
• See "Features by models" on page 7.
• The XPS printer driver can be installed only on Windows Vista OS or
higher.
• Install optional memory when an XPS job does not print because the
printer is out of memory.
• For models that provide XPS driver on the software CD:
- You can install the XPS printer driver when you insert the software CD
into your CD-ROM drive. When the installation window appears,
select Advanced Installation > Custom Installation. You can select
the XPS printer driver in the Select Software and Utilities to Install
window.
• For models that provide XPS driver from the Samsung website,
www.samsung.com > find your product> Support or downloads.
Type in the destination path and the file name, and then click OK.
For example, c:\Temp\file name.
Printing to a file (PRN)
You will sometimes need to save the print data as a file.
If you type in only the file name, the file is automatically saved in My
Documents, Documents and Settings, or Users. The saved folder may
differ, depending on your operating system or the application you are
using.
4. Special Features
204
Printing features
Understanding special printer features
You can use advanced printing features when using your machine.
To take advantage of the printer features provided by your printer driver, click Properties or Preferences in the application’s Print window to change the print
settings. The machine name, that appears in the printer properties window may differ depending on the machine in use.
• Some menus may not appear on the display depending on options or models. If so, it is not applicable to your machine.
• Select the Help menu or click the
on page 53).
Item
Multiple Pages per
Side
button from the window or press F1 on your keyboard and click on any option you want to know about (see "Using help"
Description
Selects the number of pages to print on a single sheet of paper. To print more than one page per sheet, the pages will be reduced in size and
arranged in the order you specify. You can print up to 16 pages on one sheet.
4. Special Features
205
Printing features
Item
Poster Printing
Description
Prints a single-page document onto 4 (Poster 2x2), 9 (Poster 3x3), or 16 (Poster 4x4) sheets of paper, for the purpose of pasting the sheets
together to form one poster-size document.
Select the Poster Overlap value. Specify Poster Overlap in millimeters or inches by selecting the radio button on the upper right of Basic tab
to make it easier to paste the sheets together.
Prints your document on both sides of a sheet of paper and arranges the pages so that the paper can be folded in half after printing to produce
a booklet.
Booklet Printinga
• If you want to make a booklet, you need to print on Letter, Legal, A4, US Folio, or Oficio sized print media.
8
9
• The Booklet Printing option is not available for all paper sizes. Select the available paper Size option under the Paper tab to see what
paper sizes are available.
• If you select an unavailable paper size, this option can be automatically canceled. Select only available paper (paper without
mark).
• Double-sided
Printing
• Double-sided
Printing (Manual)a
or
Print on both sides of a sheet of paper (duplex). Before printing, decide how you want your document oriented.
• You can use this feature with Letter, Legal, A4, US Folio or Oficio sized paper
• If your machine does not have a duplex unit, you should complete the printing job manually. The machine prints every other page of
the document first. After that, a message appears on your computer.
• Skip Blank Pages feature does not work when you select the duplex option.
4. Special Features
206
Printing features
Item
Description
• Double-sided
Printing
• Printer Default: If you select this option, this feature is determined by the settings you have selected on the control panel of the machine.
This option is available only when you use the PCL/XPS printer driver.
• Double-sided
• None: Disables this feature.
a
Printing (Manual)
• Long Edge: This option is the conventional layout used in bookbinding.
• Short Edge: This option is the conventional layout used in calendars.
• Reverse Double-Sided Printing: Check this option to reverse the print order when duplex printing. This option is not available when you
use Double-sided Printing (Manual).
Paper Options
Changes the size of a document to appear larger or smaller on the printed page by entering in a percentage by which to enlarge or decrease the
document.
Watermark
The watermark option allows you to print text over an existing document. For example, you use it when you want to have large gray letters
reading “DRAFT” or “CONFIDENTIAL” printed diagonally across the first page or all pages of a document.
4. Special Features
207
Printing features
Item
Watermark
(Creating a
watermark)
Watermark
(Editing a watermark)
Watermark
(Deleting a
watermark)
Description
a To change the print settings from your software application, access Printing Preferences.
b Click the Advanced tab, select Edit from the Watermark drop-down list. The Edit Watermarks window appears.
c Enter a text message in the Watermark Message box.
You can enter up to 256 characters. The message displays in the preview window.
a
b
c
d
e
To change the print settings from your software application, access Printing Preferences.
Click the Advanced tab, select Edit from the Watermark drop-down list. The Edit Watermarks window appears.
Select the watermark you want to edit from the Current Watermarks list and change the watermark message and options.
Click Update to save the changes.
Click OK or Print until you exit the Print window.
a
b
c
d
To change the print settings from your software application, access Printing Preferences.
Click the Advanced tab, select Edit from the Watermark drop-down list. The Edit Watermarks window appears.
Select the watermark you want to delete from the Current Watermarks list and click Delete.
Click OK or Print until you exit the Print window.
This option is available only when you use the PCL/SPL printer driver (see "Software" on page 7).
Overlaya
An overlay is text and/or images stored in the computer hard disk drive (HDD) as a special file format that can be printed on any document.
Overlays are often used to take the place of letterhead paper. Rather than using preprinted letterhead, you can create an overlay containing
exactly the same information that is currently on your letterhead. To print a letter with your company’s letterhead, you do not need to load
preprinted letterhead paper in the machine: just print the letterhead overlay on your document.
To use a page overlay, you must create a new page overlay containing your logo or image.
• The overlay document size must be the same as the document you print with the overlay. Do not create an overlay with a watermark.
• The resolution of the overlay document must be the same as that of the document you will print with the overlay.
4. Special Features
208
Printing features
Item
Overlaya
(Creating a new page
overlay)
Description
a
b
c
d
To save the document as an overlay, access Printing Preferences.
Click the Advanced tab, and select Edit from the Text drop-down list. Edit Overlay window appears.
In the Edit Overlay window, click Create.
In the Save As window, type a name up to eight characters in the File name box. Select the destination path, if necessary (The default is
C:\Formover).
e Click Save. The name appears on the Overlay List.
f Click OK or Print until you exit the Print window.
The file is not printed. Instead, it is stored on your computer hard disk drive.
a Click the Advanced tab.
b Select the desired overlay from the Text drop-down list.
c If the overlay file you want does not appear in the Text drop-down list, select Edit... from the list and click Load. Select the overlay file you
want to use.
If you have stored the overlay file you want to use in an external source, you can also load the file when you access the Open window.
Overlaya
After you select the file, click Open. The file appears in the Overlay List box and is available for printing. Select the overlay from the Overlay
(Using a page overlay)
List box.
d If necessary, check Confirm Page Overlay When Printing box. If this box is checked, a message window appears each time you submit a
document for printing, asking you to confirm printing an overlay on your document.
If this box is not checked and an overlay has been selected, the overlay automatically prints with your document.
e Click OK or Print until you exit the Print window.
Overlaya
(Deleting a page
overlay)
a
b
c
d
e
f
In the Printing Preferences window, click the Advanced tab.
Select Edit in the Text drop down list.
Select the overlay you want to delete from the Overlay List box.
Click Delete.
When a confirming message window appears, click Yes.
Click OK or Print until you exit the Print window. You can delete page overlays that you no longer use.
4. Special Features
209
Printing features
Item
Description
• This feature is available only if you have installed the optional memory or mass storage device (HDD) (see "Variety feature" on page 9).
• Some menus may not appear on the display depending on options or models. If so, it is not applicable to your machine.
• Print Mode: The default Print Mode is Normal, which is for printing without saving the printing file in the memory.
- Normal: This mode prints without storing your document in the optional memory.
- Proof: This mode is useful when you print more than one copy. You can print one copy first to check, then print the rest of the copies later.
Print Mode
- Confidential: This mode is used for printing confidential documents. You need to enter a password to print.
- Store: Select this setting to save a document in the mass storage device (HDD) without printing.
- Store and Print: This mode is used when printing and storing document at the same time.
- Spool: This option can be useful when handling large amounts of data. If you select this setting, the printer spools the document into the
mass storage device (HDD) and then prints it from the mass storage device (HDD) queue, decreasing the computer’s work load.
- Print Schedule: Select this setting to print the document at a specified time.
• User ID: This option is used when you need to find a saved file using the control panel.
• Job Name: This option is used when you need to find a saved file using the control panel.
Encrypts printing data first, and transmits it to the machine. This feature protects the printing information even though the data is snatched on
a network.
Job Encryption
Job Encryption feature is enabled only when the mass storage device (HDD) is installed. The mass storage device (HDD) is used to
decrypt the printing data (see "Variety feature" on page 9).
a. This option is not available when you use XPS driver.
4. Special Features
210
Printing features
Printing
15
Using Direct Printing Utility
There are several ways you can print using the Direct Printing Utility.
• Direct Printing Utility may not be available depending on model or
optional goods (see "Software" on page 7).
1
• Available for Windows OS users only.
The Direct Printing Utility window appears.
2
Select your machine from the Select Printer drop-down list and click
Browse.
3
Select the file you wish to print and click Open.
What is Direct Printing Utility?
Direct Printing Utility is a program that sends the PDF files directly to your
machine to print without having to opening the file.
To install this program, select Advanced Installation > Custom Installation
and put a check mark in this program when you install the printer driver.
From the Start menu select Programs or All Programs > Samsung
Printers > Direct Printing Utility > Direct Printing Utility.
The file is added in the Select Files section.
4
5
Customize the machine settings for your needs.
Click Print. The selected PDF file is sent to the machine.
• Mass storage device (HDD) should be installed on your machine, to print
files using this program. (see "Variety feature" on page 9).
• You cannot print PDF files that are restricted. Deactivate the printing
restriction feature and retry printing.
• You cannot print PDF files that are restricted by a password. Deactivate
the password feature, and retry printing.
• Whether or not a PDF file can be printed using the Direct Printing Utility
program depends on how the PDF file was created.?
• The Direct Printing Utility program supports PDF version 1.7 and below.
For higher versions, you must open the file to print it.
4. Special Features
211
Printing features
Using the right-click menu
16
Mac printing
1
Right-click on the PDF file to print and select Direct Printing.
The Direct Printing Utility window appears with the PDF file is added.
2
3
4
Some features may not be available depending on models or options. It
means that the features are not supported.
Select the machine to use.
Customize the machine settings.
Click Print. The selected PDF file is sent to the machine.
Printing a document
When you print with a Mac, you need to check the printer driver settings in each
application you use. Follow the steps below to print from a Mac:
1
2
Open the document to print.
3
Choose your paper size, orientation, scaling, other options, and make
sure that your machine is selected. Click OK.
4
5
6
Open the File menu and click Print.
Open the File menu and click Page Setup (Document Setup in some
applications).
Choose the number of copies and indicate which pages to print.
Click Print.
4. Special Features
212
Printing features
Changing printer settings
Printing on both sides of the paper
You can use advanced printing features when using your machine.
Open an application and select Print from the File menu. The machine name,
which appears in the printer properties window, may differ depending on the
machine in use. Except for the name, the composition of the printer properties
window is similar to the following.
Some features may not be available depending on models or options. It
means that the features are not supported (see "Variety feature" on page 9).
Before printing in the duplex mode, decide on which edge you will be binding
your finished document. The binding options are, as follows:
Printing multiple pages on one sheet
•
Long-Edge Binding: This option is the conventional layout used in book
binding.
You can print more than one page on a single sheet of paper. This feature
provides a cost-effective way to print draft copies.
•
Short-Edge Binding: This option is the type often used with calendars.
1
2
Open an application, and select Print from the File menu.
3
4
Select the other options to use.
Select Layout from the drop-down list under Orientation. In the Pages
per Sheet drop-down list, select the number of pages you want to print
on one sheet of paper.
Click Print.
The machine prints the selected number of pages to print on one sheet
of paper.
1
2
3
4
5
From your Mac application, select Print from the File menu.
Select Layout from the drop-down list under Orientation.
Select a binding orientation from the Two-Sided option.
Select the other options to use.
Click Print and the machine prints on both sides of the paper.
If you print more than 2 copies, the first copy and the second copy might
print on the same sheet of paper. Avoid printing on both sides of paper
when you are printing more than 1 copy.
4. Special Features
213
Printing features
Using help
Printing from applications
Click the question mark on the bottom-left corner of the window and click on
the topic you want to know about. A pop-up window appears with information
about that option's feature, which is provided from the driver.
There are a lot of Linux applications that allow you to print using Common UNIX
Printing System (CUPS). You can print on your machine from any such
application.
17
Linux printing
Some features may not be available depending on models or options. It
means that the features are not supported.
1
2
Open an application, and select Print from the File menu
3
Choose your paper size, orientation, and make sure that your machine is
selected. Click Apply.
4
5
6
7
8
Open the File menu and click Print.
Open the File menu and click Page Setup (Print Setup in some
applications).
Select your machine to print.
Choose the number of the copies and indicate which pages to print.
Change other printing options in each tab, if necessary.
Click Print.
Automatic/manual duplex printing may not be available depending on
models. You can alternatively use the lpr printing system or other
applications for odd-even printing.
4. Special Features
214
Printing features
Printing files
You can print many different types of files on your machine using the standard
CUPS, directly from the command line interface. The CUPS lpr utility allows you
to do that. You can print these files by using below command format.
“lp -d <printer name> -o <option> <file name>”
Please refer to lp or lpr man page on your system for more details.
Configuring Printer Properties
You can change the default printing options or connection type with Printing
utility supplied by O/S.
1
Launch Printing utility (Go to System > Administration > Printing
menu or execute “System-config-printer“ command in Terminal
program).
2
3
4
Select your printer and double-click it.
Change default printing options or connection type.
Click Apply button.
4. Special Features
215
Scan features
•
TWAIN: TWAIN is the one of a preset imaging applications. Scanning an
image launches the selected application, enabling you to control the
scanning process. This feature can be used via the local connection or the
network connection (see "Scanning from image editing program" on page
220).
•
Samsung Easy Document Creator: You can use this program to scan
images or documents (see"Scanning with Samsung Easy Document
Creator" on page 221).
•
WIA: WIA stands for Windows Images Acquisition. To use this feature, your
computer must be connected directly with the machine via an USB cable
(see "Scanning using the WIA driver" on page 221).
•
USB Memory: You can scan a document and save the scanned image onto
an USB memory device.
•
FTP/SMB: You can scan an image and upload it to an FTP/SMB server (see
"Scanning to FTP/SMB server" on page 219).
• For basic scanning features, refer to the Basic Guide (see "Basic scanning"
on page 61).
• This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
• The maximum resolution that can be achieved depends upon various
factors, including computer speed, available disk space, memory, the
size of the image being scanned, and bit depth settings. Thus, depending
on your system and what you are scanning, you may not be able to scan
at certain resolutions, especially using enhanced dpi.
18
Basic scanning method
This feature may not be available depending on model or optional goods
(see "Variety feature" on page 9).
You can scan the originals with your machine via an USB cable or the network.
The following methodoloqies can be used for scanning your documents:
•
Scan to PC: Scan the originals from the control panel. Then, the scanned
data will be stored in the connected computers My Documents folder (see
"Basic Scanning" on page 61).
4. Special Features
216
Scan features
19
20
Setting the scan settings in the computer
Scanning from network connected machine
This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
1
Open Samsung Easy Printer Manager (see "Using Samsung Easy
Printer Manager" on page 244).
2
3
4
Select the appropriate machine from the Printer List.
Select Scan to PC Settings menu.
Make sure the printer driver is installed on your computer using the software CD,
since the printer driver includes the scan program (see "Installing the driver
locally" on page 28).
1
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
2
Select
Select the option you want.
•
•
•
5
The machine that does not support the network interface, it will not be able
to use this feature (see "Rear view" on page 22).
Scan Activation: Determines whether or not scanning is enabled on
the device.
(Scan) > Scan to PC > Network PC on the control panel.
Or select Scan > Network PC.
Basic tab: Contains settings related to general scan and device
settings.
If you see Not Available message, check the port connection.
Image tab: Contains settings related to image altering.
Press Save > OK.
3
Select your registered computer ID, and enter the Password if
necessary.
4. Special Features
217
Scan features
21
• ID is the same ID as the registered scan ID for Samsung Easy Printer
Manager >
Switch to advanced mode > Scan to PC Settings.
• Password is the 4 digit number registered password for Samsung Easy
Printer Manager >
Settings.
4
5
Scanning to WSD
Switch to advanced mode > Scan to PC
Scans the originals and saves the scanned data on a connected computer if the
computer supports the WSD (Web Service for Device) feature. To use the WSD
feature, you need to install the WSD printer driver on your computer. For
Windows 7, you can install the WSD driver by Control Panel > Devices and
Printers > Add a printer. Click Add a network printer from the wizard.
Select the option you want and press OK.
• The machine that does not support the network interface, it will not be
able to use this feature (see "Features by models" on page 7).
Scanning begins.
• The WSD feature works only with Windows Vista® or later version that are
the WSD-compliant computer.
Scanned image is saved in computer’s C:\Users\users name\My
Documents. The saved folder may differ, depending on your operating
system or the application you are using.
• The following installation steps are based on Windows 7 computer.
Installing a WSD Printer Driver
1
2
3
SelectStart > Control Panel > Devices and Printers > Add a printer.
Click Add a network, wireless or Bluetooth printer from the wizard.
In the printers list, select the one you want to use, and then click Next.
4. Special Features
218
Scan features
5
6
• The IP address for WSD printer is http://IP address/ws/ (example: http://
111.111.111.111/ws/).
• If no WSD printer is displayed in the list, click The printer that I want
isn't listed > Add a printer using a TCP/IP address or hostname and
select Web Services Device from Device type. Then enter the printer's
IP address.
4
Select the option you want and press OK.
Scanning begins.
22
Scanning to FTP/SMB server
Follow the instructions in the installation window.
This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
Scanning using the WSD feature
1
Make sure that the machine is connected to your computer and
powered on.
2
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
3
Select
(Scan) > Scan to WSD on the control panel.
If you see Not Available message, check the port connection. Or check the
printer driver for WSD is correctly installed.
4
Select your computer name from WSD PC List.
Setting up an FTP/SMB server
1
Access the SyncThru™ Web Service (see "Using SyncThru™ Web Service"
on page 240).
2
3
4
5
6
Select Address Book > Individual > Add.
Check the box next to Add FTP or Add SMB.
Enter the IP address in dotted decimal notation or as a host name.
Enter the server port number, from 1 to 65535.
Check the box next to Anonymous, then the server permits the access
of unauthorized people.
4. Special Features
219
Scan features
7
8
9
Enter the login name and password.
Enter the domain name if your server is joined to the certain domain,
otherwise just enter your computer name which is registered to the SMB
server.
• The folder properties need to be setup as a share.
• Your user name should have the rights to read and write the folder.
23
Scanning from image editing program
You can scan and import documents at the image editing software such as
Adobe Photoshop, if the software is TWAIN-compliant. Follow the steps below
to scan with TWAIN-compliant software:
1
Make sure that the machine is connected to your computer and
powered on.
2
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
3
4
5
6
Open an application, such as Adobe Photoshop.
Press Apply.
Scanning and sending to FTP/SMB server
1
2
3
The machine begins scanning and then sends the scanned image to the
specified server.
Enter the path for saving the scanned image.
• The folder to save the scanned image must be on the root.
10
5
Make sure that your machine is connected to a network.
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
Select
(scan) > Scan to SMB or Scan to FTP on the control panel.
Click File > Import, and select the scanner device.
Set the scan options.
Scan and save your scanned image.
Or select Scan > SMB or FTP.
4
Select a server and scan format you want.
4. Special Features
220
Scan features
24
Scanning using the WIA driver
Your machine supports the Windows Image Acquisition (WIA) driver for
scanning images. WIA is one of the standard components provided by Microsoft
Windows 7 and works with digital cameras and scanners. Unlike the TWAIN
driver, the WIA driver allows you to scan and easily adjust images without using
additional software:
The WIA driver works only on Windows OS (not supported Windows 2000)
with a USB port.
1
Make sure that the machine is connected to your computer and
powered on.
2
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
3
Click Start > Control Panel > Hardware and Sound > Devices and
Printers.
4
5
Right-click on device driver icon in Printers and Faxes > Start Scan.
6
Choose your scanning preferences and click Preview to see your
preferences affect the picture.
7
Scan and save your scanned image.
25
Scanning with Samsung Easy Document Creator
Samsung Easy Document Creator is an application to help users scan, compile,
and save documents in multiple formats, including .epub format.
We recommend using scan features with the Samsung Easy Document Creator
program provided in the supplied sofware CD.
• Availabe for Windows OS users only.
• Windows XP or higher and Internet Explorer 6.0 or higher is the minimum
requirement for Samsung Easy Document Creator.
• Samsung Easy Document Creator is installed automatically when you
install the machine software (see "Using Samsung Easy Document
Creator" on page 243).
New Scan application appears.
4. Special Features
221
Scan features
1
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
26
2
From the Start menu select Programs or All Programs.
Scanning from USB connected machine
•
3
Mac scanning
For Windows 8, from Charms, select Search > Apps.
Click Samsung Printers, and start Samsung Easy Document Creator.
Click Scan (
) from the home screen.
4
5
6
Select the type of scanning or a favorites then click Start.
7
8
Select to Save to Location, Send to E-mail, or Send to SNS.
Make adjustments to the image (Scan Settings and More Options).
1
Make sure that the machine is connected to your computer and
powered on.
2
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
3
Start Applications and click Image Capture.
Click Scan to scan a final image or Prescan to get another preview
image.
Click on Save (Saving a Scan), Send ( E-mailing a Scan), or Share
(Uploading).
If there is room on the document glass, more than one item can be scanned
at the same time. Use the
If No Image Capture device connected message appears, disconnect the
USB cable and reconnect it. If the problem continues, refer to the Image
Capture’s help.
4
5
Select the option you want.
Scan and save your scanned image.
tool to make multiple selection areas.
If scanning does not operate in Image Capture, update Mac OS to the latest
version.
4. Special Features
222
Scan features
Scanning from network connected machine
• If scanning does not operate in Image Capture, update Mac OS to the
latest version.
• For more information, refer to the Image Capture’s help.
Network or wireless model only (see "Features by models" on page 7).
• You can also scan using TWAIN-compliant software, such as Adobe
Photoshop.
1
2
3
4
Make sure that your machine is connected to a network.
Place a single document face down on the document glass, or load the
documents face up into the document feeder (see "Loading originals" on
page 47).
Start Applications and click Image Capture.
According to OS, follow steps below.
•
•
5
6
For 10.5
-
Click Devices > Browse Devices on Menu bar.
-
Make sure that Connected checkbox is checked beside your
machine in Bonjour Devices.
For 10.6 -10.8, select your device below SHARED.
Set the scan options on this program.
Scan and save your scanned image.
• You can scan using Samsung Scan Assistant software. Open the
Applications folder > Samsung folder > Samsung Scan Assistant.
27
Linux scanning
Scanning
1
Make sure that the machine is connected to your computer and
powered on.
2
Launch a scan application such as xsane or simple-scan (If it is not
installed, please install it to use scan features).
3
4
Select your device from the list and set the scan options to apply.
Click Scan button.
4. Special Features
223
Scan features
Editing an image with Image Manager
The Image Manager application provides you with menu commands and tools
to edit your scanned image.
4. Special Features
224
Fax features
29
• For basic faxing features, refer to the Basic Guide (see "Basic faxing" on
page 62).
Redialing the fax number
• This function is not supported for M207x series (see "Control panel
overview" on page 23).
1
2
Press
(Redial/Pause) button on the control panel.
Select the fax number you want.
Ten recently sent fax numbers with ten received Caller IDs are shown.
28
Automatic redialing
3
When the number you have dialed is busy or there is no answer when you send
a fax, the machine automatically redials the number. The redial time depends on
the country's factory default setting.
When the display shows Retry Redial?, press
When an original is loaded in the document feeder, the machine
automatically begins to send.
If an original is placed on the scanner glass, select Yes to add another
page. Load another original and press OK. When you have finished,
select No when Another Page? appears.
(Start) button to redial the
30
number without waiting. To cancel the automatic redialing, press
(Cancel or
Stop/Clear).
To change the time interval between redials and the number of redial attempts.
1
Press
panel.
(fax) >
(Menu)> Fax Setup > Sending on the control
Confirming a transmission
When the last page of your original has been sent successfully, the machine
beeps and returns to ready mode.
When something goes wrong while sending your fax, an error message appears
on the display. If you receive an error message, press
2
3
Select Redial Times or Redial Term you want.
(Cancel or Stop/Clear)
to clear the message and try to send the fax again.
Select the option you want.
4. Special Features
225
Fax features
5
You can set your machine to print a confirmation report automatically each
time sending a fax is completed. Press
(fax) >
> Sending > Fax Confirm on the control panel.
(Menu) > Fax Setup
Enter the recipients’ numbers and select the option
Select the Help menu or click the
button from the window and click on
any option you want to know about.
6
31
Sending a fax in the computer
Click Send.
32
Delaying a fax transmission
• This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
You can set your machine to send a fax at a later time when you will not be
present. You cannot send a color fax using this feature.
You can send a fax from your computer without going to the machine.
To send a fax from your computer, the Samsung Network PC Fax program
must be installed. This program will be installed when you installed the printer
driver.
1
2
Open the document to be sent.
Select Print from the File menu.
1
Place a single document face down on the document glass, or load the
documents face up into the document feeder.
2
3
4
Press
The Print window will be displayed. It may look slightly different
depending on your application.
3
4
Select Samsung Network PC Fax from the Print window
Click Print or OK.
(fax) on the control panel.
Adjust the resolution and the darkness to suit your fax needs.
Press
(Menu) > Fax Feature > Delay Send on the control panel.
Or select Fax > Delayed Send > To.
5
6
Enter the number of the receiving fax machine and press OK.
The display asks you to enter another fax number to send the document.
4. Special Features
226
Fax features
7
To enter more fax numbers, press OK when Yes highlights and repeat
steps 5.
1
Place a single document face down on the document glass, or load the
documents face up into the document feeder.
• Once you entered a group dial number, you cannot enter another group
dial numbers anymore.
2
Press
panel.
Enter the job name and the time.
3
Select the fax job and press OK.
• You can add up to 10 destinations.
8
If you set a time earlier than the current time, the fax will be sent at that time
on the following day.
9
Adding documents to a reserved fax
The original is scanned into memory before transmission.
The machine returns to ready mode. The display reminds you that you
are in ready mode and that a delayed fax is set.
You can check the list of delayed fax jobs.
Press
(Menu) > System Setup > Report > Schedule Jobs on the
control panel.
(fax) >
(Menu) > Fax Feature > Add Page on the control
When you have finished, select No when Another Page? appears. The
machine scans the original into memory.
4
Press
(Cancel or Stop/Clear) to return to ready mode.
Canceling a reserved fax job
1
Press
panel.
(fax) >
(Menu) > Fax Feature > Cancel Job on the control
2
3
Select the fax job you want and press OK.
Press OK when Yes highlights.
The selected fax is deleted from memory.
4
Press
(Stop/Clear) to return to ready mode.
4. Special Features
227
Fax features
33
34
Sending a priority fax
This function is used when a high priority fax need to be sent ahead of reserved
operations. The original is scanned into memory and immediately transmitted
when the current operation is finished.
1
Place a single document face down on the document glass, or load the
documents face up into the document feeder.
2
Press
(Fax) >
control panel.
(Menu) > Fax Feature > Priority Send on the
Forwarding a sent fax to another destination
You can set the machine to forward the sent fax to other destination by a fax. If
you are out of office but have to receive the fax, this feature may be useful.
• Though you sent or received a color fax, the data is forwarded in
grayscale.
1
Place a single document (see "Loading originals" on page 47).
2
Press
(fax) >
(Menu) > Fax Feature > Send Forward > Forward
to Fax > On on the control panel.
Or select Fax > Priority Send > To.
3
4
5
Enter the destination fax number and press OK.
Enter the job name and press OK.
If an original is placed on the scanner glass, select Yes to add another
pages. Load another original and press OK.
When you have finished, select No when Another Page? appears.
The machine starts to scan and send a fax to destinations.
4. Special Features
228
Fax features
35
Forward options may not be available depending on model or optional
goods (see "Variety feature" on page 9).
3
Enter the destination fax number, email address, or server address and
press OK.
4
Press
Forwarding a received fax
You can set the machine to forward the received fax to other destination by a fax
or a PC. If you are out of office but have to receive the fax, this feature may be
useful.
(Stop/Clear) to return to ready mode.
Though you sent or received a color fax, the data is forwarded in grayscale.
Subsequent sent faxes will be forwarded to the specified fax machine.
1
Press
(fax) >
(Menu) > Fax Feature > Rcv.Forward > Forward
to Fax, or Forward to PC > On on the control panel.
Forward options may not be available depending on model or optional
goods (see "Variety feature" on page 9).
2
To set the machine to print out a fax when fax forwarding has been
completed, select Forward & Print.
3
Enter the destination fax number, email address, or server address and
press OK.
4
5
Enter the starting tim and ending time, then press OK.
Press
(Stop/Clear) to return to ready mode.
Subsequent sent faxes will be forwarded to the specified fax machine.
4. Special Features
229
Fax features
36
•
Notify me when complete: Set to show the popup window to notify
receiving a fax.
•
Open with default application: After receiving the fax, open it with
default application.
•
None: After receiving a fax, the machine does not notify the user or
opens the application.
Receiving a fax in the computer
• This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
• To use this feature, set the option on the control panel:
Press
(fax) >
(Menu) > Fax Feature > RCV.Forward > Forward
to PC > On the control panel.
Or select Setup > Machine Setup > Next > Fax Setup > Forward > PC
> On.
1
2
3
4
Open the Samsung Easy Printer Manager.
5
37
Changing the receive modes
1
Select the appropriate machine from the Printer List.
•
Image Type: Convert the received faxes to PDF or TIFF.
•
Save Location: Select location to save the converted faxes.
•
Prefix: Select prefix.
•
Print received fax: After receiving the fax, set prints information for
the received fax.
Press
(fax) >
(Menu) > Fax Setup > Receiving > Receive Mode
on the control panel.
Or select Setup > Machine Setup > Next > Default Setting > Fax
Default > Common > Receive Mode.
Select Fax to PC Settings menu.
Use Enable Fax Receiving from Device to change the fax settings.
Press Save > OK.
2
Select the option you want.
•
Fax: Answers an incoming fax call and immediately goes into the fax
reception mode.
•
Tel: Receives a fax by pressing
(On Hook Dial) and then
(Start) button.
4. Special Features
230
Fax features
•
Ans/Fax: Is for when an answering machine attached to your
machine. Your machine answers an incoming call, and the caller can
leave a message on the answering machine. If the fax machine
senses a fax tone on the line, the machine automatically switches to
Fax mode to receive the fax.
38
Receiving manually in Tel mode
You can receive a fax call by pressing
pressing
To use the Ans/Fax mode, attach an answering machine to the EXT socket
on the back of your machine.
(On Hook Dial) button and then
(Start) when you hear a fax tone.
39
Receiving in Answering Machine/Fax mode
•
DRPD: You can receive a call using the Distinctive Ring Pattern
Detection (DRPD) feature. Distinctive Ring is a telephone company
service which enables an user to use a single telephone line to
answer several different telephone numbers. For further details, see
"Receiving faxes using DRPD mode" on page 232.
This setting may not be available depending on your country.
3
4
Press OK.
Press
(Cancel or Stop/Clear) to return to ready mode.
To use this mode, you must attach an answering machine to the EXT socket on
the back of your machine. If the caller leaves a message, the answering machine
stores the message. If your machine detects a fax tone on the line, it
automatically starts to receive the fax.
• If you have set your machine to this mode and your answering machine
is switched off, or no answering machine is connected to EXT socket,
your machine automatically goes into Fax mode after a predefined
number of rings.
• If the answering machine has a user-selectable ring counter, set the
machine to answer incoming calls within 1 ring.
• If the machine is in Tel mode, disconnect or switch off the answering
machine with the fax machine. Otherwise, the outgoing message from
the answering machine will interrupt your phone conversation.
4. Special Features
231
Fax features
40
Receiving faxes with an extension telephone
When you are using an extension telephone connected to the EXT socket, you
can receive a fax from someone you are talking to on the extension telephone,
without going to the fax machine.
This setting may not be available depending on your country.
1
Or select Setup > Machine Setup > Next > Default Setting > Fax
Default > Common > Receive Mode > DRPD.
When you receive a call on the extension phone and hear fax tones, press the
keys *9* on the extension phone. The machine receives the fax.
*9* is the remote receive code preset at the factory. The first and the last
asterisks are fixed, but you can change the middle number to whatever you
want.
Select
(fax) >
(Menu) > Fax Setup > Receiving > DRPD Mode
> Waiting Ring on the control panel.
2
3
Call your fax number from another telephone.
When your machine begins to ring, do not answer the call. The machine
requires several rings to learn the pattern.
When the machine completes learning, the display shows Completed
DRPD Setup. If the DRPD setup fails, Error DRPD Ring appears.
While you are talking over the telephone connected to the EXT socket, copy
and scan features are not available.
4
Press OK when DRPD appears and start over from step 2.
41
Receiving faxes using DRPD mode
Distinctive Ring is a telephone company service which enables an user to use a
single telephone line to answer several different telephone numbers. This
feature is often used by answering services who answer telephones for many
different clients and need to know which number someone is calling in on to
properly answer the phone.
• DRPD must be set up again if you re-assign your fax number, or connect
the machine to another telephone line.
• After DRPD has been set up, call your fax number again to verify that the
machine answers with a fax tone. Then have a call placed to a different
number assigned to that same line to be sure the call is forwarded to the
extension telephone or answering machine plugged into the EXT socket.
4. Special Features
232
Fax features
3
42
Receiving in secure receiving mode
The machine prints all of the faxes stored in memory.
43
Receiving faxes in memory
This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
You may need to prevent your received faxes from being accessed by
unauthorized people. Turn on secure receiving mode, then all incoming faxes
go into memory. You can print the incoming faxes with entering the password.
Since your machine is a multi-tasking device, it can receive faxes while you are
making copies or printing. If you receive a fax while you are copying or printing,
your machine stores incoming faxes in its memory. Then, as soon as you finish
copying or printing, the machine automatically prints the fax.
If fax is received and being printed, other copy and print jobs cannot be
processed at the same time.
To use the secure receiving mode, activate the menu from
(fax) >
(Menu) > Fax Feature > Secure Receive on the control panel.
Or select Setup > Machine Setup > Next > Fax Setup > Secure Receive.
44
Printing sent fax report automatically
Printing received faxes
1
Select
(fax) >
(Menu) > Fax Feature > Secure Receive > Print
on the control panel.
Or select Setup > Machine Setup > Next > Fax Setup > Secure Receive
> Print.
2
You can set the machine to print a report with detailed information about the
previous 50 communication operations, including time and dates.
1
Press
(fax) >
control panel.
2
Press
(Menu) > Fax Setup > Auto Report > On on the
(Cancel or Stop/Clear) to return to ready mode.
Enter a four-digit password and press OK.
4. Special Features
233
Using shared folder features
This feature allows you to use the machine’s memory as a shared folder. The
advantage of this feature is that you can conveniently use the shared folder
through your computer’s window.
• This feature may not be available depending on model or optional goods
(see "Features by models" on page 7).
• You can use this feature in the models that have a mass storage device
(see "Variety feature" on page 9).
46
Using the shared folder
You can use the shared folder in the same way exactly like the normal computer.
Create, edit and delete the folder or file as a normal Windows folder. You also
store the scanned data in the shared folder. You can directly print files stored on
a the shared folder. You can print TIFF, BMP, JPEG and PRN files.
• The administrator can set the ID and password to restrict the user’ s
access and also set the maximum number of simultaneous users.
45
Creating a shared folder
1
2
3
Open the Windows Explore window from the computer.
Enter the printer’s \\[ip address] (example: \\169.254.133.42) in the
address field, and press the Enter key or click Go.
Create a new folder under nfsroot directory.
4. Special Features
234
Using memory/hard drive features
From the control panel
You can use this feature in the models that have a mass storage device
(HDD) or memory (see "Variety feature" on page 9).
If your machine has optional memory or an optional hard drive, you can use
these features from the
(Menu) button> System Setup > Job
Management.
47
Setting up the optional memory
From the printer driver
After installing the optional memory, you can use advanced printing features,
such as proofing a job and specifying of printing a private job in the Print
window. Select Properties or Preference, and configure the printing mode.
•
Active Job: All of the print jobs waiting to be printed are listed in the active
job queue in the order you sent them to the printer. You can delete a job
from the queue before printing, or promote a job to print sooner.
•
File Policy: You can choose the file policy for generating file name before
you proceed with the job through optional memory. If the optional memory
already has the same name when you entered a new file name, you can
rename or overwrite it.
•
Stored Job: You can print or delete a stored job.
• Some menus may not appear on the display depending on options or
models. If so, it is not applicable to your machine.
• After installing the hard drive, you can also print the predefined
document templates from the
Form Menu.
(Menu) button > System Setup >
4. Special Features
235
5. Useful Management
Tools
This chapter introduces management tools provided to help you make full use of your machine.
• Easy Capture Manager
237
• Samsung AnyWeb Print
238
• Easy Eco Driver
239
• Using SyncThru™ Web Service
240
• Using Samsung Easy Document Creator
243
• Using Samsung Easy Printer Manager
244
• Using Samsung Printer Status
247
Easy Capture Manager
• This feature may not be available depending on model or optional goods (see "Software" on page 7).
• Available for Windows OS users only (see "Software" on page 7).
Capture your screen and launch Easy Capture Manager by simply pressing the Print Screen key. Now you can easily print your captured screen as captured or edited.
5. Useful Management Tools
237
Samsung AnyWeb Print
• This feature may not be available depending on model or optional goods (see "Software" on page 7).
• Available for Windows and Mac OS users only (see "Software" on page 7).
This tool helps you screen-capture, preview, scrap, and print Windows Internet Explorer pages more easily, than when you use an ordinary program. Click Start > All
programs > Samsung Printers > Samsung AnyWeb Print > Download the latest version to link to the website where the tool is available for download.
5. Useful Management Tools
238
Easy Eco Driver
• Available for Windows OS users only.
• This feature may not be available depending on model or optional goods (see "Features by models" on page 7).
With the Easy Eco Driver, you can apply Eco features to save paper and toner before printing. To use this application, Start Easy Eco Driver before printing job
checkbox in the printer properties should be checked.
Easy Eco Driver also allows you simple editing such as removing images and texts, changing fonts, and more. You can save frequently used settings as a preset.
How to use:
1 Open a document to print.
2 Print the document.
A preview window appears.
3 Select the options you want to apply to the document.
You can see the preview of the applied features.
4 Click Print.
5. Useful Management Tools
239
Using SyncThru™ Web Service
1
2
• Internet Explorer 6.0 or higher is the minimum requirement for
SyncThru™ Web Service.
• SyncThru™ Web Service explanation in this user’s guide may differ from
your machine depending on its options or models.
• Network model only (see "Software" on page 7).
Click Login on the upper right of the SyncThru™ Web Service website.
Type in the ID and Password then click Login.
•
ID: admin
•
Password: sec00000
2
SyncThru™ Web Service overview
1
Accessing SyncThru™ Web Service
1
Access a web browser, such as Internet Explorer, from Windows.
Enter the machine IP address of your printer (http://xxx.xxx.xxx.xxx) in
the address field and press the Enter key or click Go.
2
Some tabs may not appear depending on your model.
Your machine’s embedded website opens.
Logging into SyncThru™ Web Service
Before configuring options in SyncThru™ Web Service, you need to log-in as an
administrator. You can still use SyncThru™ Web Service without logging in but
you won’t have access to Settings tab and Security tab.
Information tab
This tab gives you general information about your machine. You can check
things, such as remaining amount of toner. You can also print reports.
•
Active Alerts: Shows the alerts that have occurred in the machine and their
severity.
•
Supplies: Shows how many pages are printed and amount of toner left in
the cartridge.
•
Usage Counters: Shows the usage count.
5. Useful Management Tools
240
Using SyncThru™ Web Service
•
Current Settings: Shows the machine’s and network’s information.
•
Print information: Prints reports such as system related reports, e-mail
address, and font reports.
Settings tab
This tab allows you to set configurations provided by your machine and
network. You need to log-in as an administrator to view this tab.
•
Machine Settings tab: Sets options provided by your machine.
•
Network Settings tab: Shows options for the network environment. Sets
options such as TCP/IP and network protocols.
Maintenance tab
This tab allows you to maintain your machine by upgrading firmware and
setting contact information for sending emails. You can also connect to
Samsung website or download drivers by selecting the Link menu.
•
Firmware Upgrade: Upgrade your machine’s firmware.
•
Contact Information: Shows the contact information.
•
Link: Shows links to useful sites where you can download or check
information.
3
E-mail notification setup
Security tab
This tab allows you to set system and network security information. You need to
log-in as an administrator to view this tab.
•
System Security: Sets the system administrator’s information and also
enables or disables machine features.
•
Network Security: Sets settings for HTTPs, IPSec, IPv4/IPv6 filtering, 802.1x,
and Authentication servers.
•
User Access Control: Classifies users into several groups according to each
user’s role. Each user’s authorization, authentication and accounting will be
controlled by the group’s role definition.
You can receive emails about your machine’s status by setting this option. By
setting information such as IP address, host name, e-mail address and SMTP
server information, the machine status (toner cartridge shortage or machine
error) will be sent to a certain person's e-mail automatically. This option may be
used more frequently by a machine administrator.
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine.
5. Useful Management Tools
241
Using SyncThru™ Web Service
1
Start a web browser, such as Internet Explorer, from Windows.
Enter the machine IP address (http://xxx.xxx.xxx.xxx) in the address field
and press the Enter key or click Go.
4
Setting the system administrator’s information
This setting is necessary for using the e-mail notification option.
2
3
Your machine’s embedded website opens.
From the Settings tab, select Machine Settings > E-mail Notification.
If you have not configured outgoing server environment, go to Settings >
Network Settings > Outgoing Mail Server(SMTP) to configure network
environment before setting e-mail notification.
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine.
1
Start a web browser, such as Internet Explorer, from Windows.
Enter the machine IP address (http://xxx.xxx.xxx.xxx) in the address field
and press the Enter key or click Go.
4
5
Select Enable check box to use the E-mail Notification.
Click Add button to add e-mail notification user.
Set the recipient name and e-mail address(es) with notification items
you want to receive an alert for.
6
2
3
4
Your machine’s embedded website opens.
5
Click Apply.
Click Apply.
From the Security tab, select System Security > System Administrator
Enter the name of the administrator, phone number, location, and email
address.
If the firewall is activated, the e-mail may not be sent successfully. In that
case, contact the a network administrator.
5. Useful Management Tools
242
Using Samsung Easy Document Creator
Samsung Easy Document Creator is an application to help users scan, compile,
and save documents in multiple formats, including .epub format. These
documents can be shared via social networking sites or fax. Whether you’re a
student needing to organize research from the library or a stay-at-home mom
sharing scanned pictures from last year’s birthday party, Samsung Easy
Document Creator will provide you with the necessary tools.
The Samsung Easy Document Creator provides features below:
•
Image Scanning: Use for scanning single or mulitple pictures.
•
Document Scanning: Use for scanning documents with text or text and
images.
•
Text Converting: Use for scanning documents that need to be saved in an
editable text format.
•
Book Scanning: Use for scanning books with the flatbed scanner.
•
SNS Upload: Provides an easy and quick way to upload scanned image or
existing images to a variety of social networking sites (SNS).
•
E-Book Conversion: Provides the ability to scan multiple documents in as
one e-book or convert existing files into an e-book format.
•
Plug-in: Scan, fax, and convert to E-Book directly from the Microsoft Office
program.
Click the Help ( ) button from the window and click on any option you
want to know about.
5. Useful Management Tools
243
Using Samsung Easy Printer Manager
• This feature may not be available depending on model or optional goods
(see "Software" on page 7).
The Samsung Easy Printer Manager interface is comprised of various basic
sections as described in the table that follows:
• Available for Windows and Mac OS users only (see "Software" on page 7).
The screenshot may differ depending on operating system you are using.
• For Windows, Internet Explorer 6.0 or higher is the minimum
requirement for Samsung Easy Printer Manager.
Samsung Easy Printer Manager is an application that combines Samsung
machine settings into one location. Samsung Easy Printer Manager combines
device settings as well as printing environments, settings/actions and
launching. All of these features provide a gateway to conveniently use your
Samsung machine. Samsung Easy Printer Manager provides two different user
interfaces for the user to choose from: the basic user interface and the advanced
user interface. Switching between the two interfaces is easy: just click a button.
5
Understanding Samsung Easy Printer Manager
To open the program:
For Windows,
Select Start > Programs or All Programs > Samsung Printers > Samsung
Easy Printer Manager > Samsung Easy Printer Manager.
For Mac,
Open the Applications folder > Samsung folder > Samsung Easy Printer
Manager.
Printer list
1
The Printer List displays printers installed on your
computer and network printers added by network
discovery (Windows only).
5. Useful Management Tools
244
Using Samsung Easy Printer Manager
Printer
information
2
This area gives you general information about your
machine. You can check information, such as the machine’s
model name, IP address (or Port name), and machine
status.
Application
information
Includes links for changing to the advanced settings,
preference, help, and about.
The
button is used to change the user
interface to the advanced settings user interface
(see "Advanced settings user interface overview"
on page 246).
Displays Quick links to machine specific functions. This
section also includes links to applications in the advanced
settings.
4
If you connect your machine to a network, the
SyncThru™ Web Service icon is enabled.
You can view the online User’s Guide.
Troubleshooting button: This button opens the
Troubleshooting Guide when an error occurs.
You can directly open the necessary section in the
user’s guide.
3
Quick links
Contents area
Displays information about the selected machine,
remaining toner level, and paper. The information will vary
based on the machine selected. Some machines do not
have this feature.
Order supplies
Click on the Order button from the supply ordering
window. You can order replacement toner cartridge(s)
from online.
5
6
Select the Help menu or click the
button from the window and click on
any option you want to know about.
5. Useful Management Tools
245
Using Samsung Easy Printer Manager
Fax to PC Settings
6
Advanced settings user interface overview
The advanced user interface is intended to be used by the person responsible
for managing the network and machines.
This menu includes settings related to the basic fax functionality of the selected
device.
•
Disable: If Disable is On, incoming faxes will not be received on this device.
•
Enable Fax Receiving from Device: Enables faxing on the device and allow
more options to be set.
Some menus may not appear in the display depending on options or
models. If so, it is not applicable to your machine.
Alert Settings (Windows only)
Device Settings
You can configure various machine settings such as machine setup, paper,
layout, emulation, network, and print information.
This menu includes settings related to error alerting.
•
Printer Alert: Provides settings related to when alerts will be received.
•
Email Alert: Provides options relating to receiving alerts via email.
•
Alert History: Provides a history of device and toner related alerts.
Scan to PC Settings
This menu includes settings to create or delete scan to PC profiles.
•
Scan Activation: Determines whether or not scanning is enabled on the
device.
•
Basic tab: Contains settings related general scan and device settings.
•
Image tab: Contains settings related to image altering.
Job Accounting
Provides querying of quota information of the specified job accounting user.
This quota information can be created and applied to devices by job accounting
software such as SyncThru™ or CounThru™ admin software.
5. Useful Management Tools
246
Using Samsung Printer Status
The Samsung Printer Status is a program that monitors and informs you of the
machine status.
Icon
• The Samsung Printer Status window and its contents shown in this user’s
guide may differ depending on the machine or operating system in use.
Mean
Normal
The machine is in ready mode and experiencing no
errors or warnings.
Warning
The machine is in a state where an error might occur in
the future. For example, it might be in toner low status,
which may lead to toner empty status.
Error
The machine has at least one error.
• Check the operating system(s) that are compatible with your machine
(see "Specifications" on page 104).
• Available for Windows OS users only (see "Software" on page 7).
Description
7
Samsung Printer Status overview
If an error occurs while operating, you can check the error from the Samsung
Printer Status. Samsung Printer Status is installed automatically when you install
the machine software.
You can also launch Samsung Printer Status manually. Go to the Printing
Preferences, click the Basic tab > Printer Status button.
These icons appear on the Windows task bar:
Toner Level
You can view the level of toner remaining in each
toner cartridge. The machine and the number of
toner cartridge(s) shown in the above window may
differ depending on the machine in use. Some
machines do not have this feature.
Option
You can set printing job alert related settings.
1
2
5. Useful Management Tools
247
Using Samsung Printer Status
3
Order Supplies
You can order replacement toner cartridge(s) from
online.
User’s Guide
You can view the online User’s Guide.
This button opens the Troubleshooting
Guide when an error occurs. You can directly
open the troubleshooting section in the
user’s guide.
4
5
Close
Close the window.
5. Useful Management Tools
248
6. Troubleshooting
This chapter gives helpful information for what to do if you encounter an error.
• Paper feeding problems
250
• Power and cable connecting problems
251
• Printing problems
252
• Printing quality problems
256
• Copying problems
264
• Scanning problems
265
• Faxing problems
267
• Operating system problems
269
Paper feeding problems
Condition
Suggested solutions
Paper jams during printing.
Clear the paper jam.
Paper sticks together.
• Check the maximum paper capacity of the tray.
• Make sure that you are using the correct type of paper.
• Remove paper from the tray and flex or fan the paper.
• Humid conditions may cause some paper to stick together.
Multiple sheets of paper do not feed.
Different types of paper may be stacked in the tray. Load paper of only one type, size, and weight.
Paper does not feed into the machine.
• Remove any obstructions from inside the machine.
• Paper has not been loaded correctly. Remove paper from the tray and reload it correctly.
• There is too much paper in the tray. Remove excess paper from the tray.
• The paper is too thick. Use only paper that meets the specifications required by the machine.
The paper keeps jamming.
• There is too much paper in the tray. Remove excess paper from the tray. If you are printing on special materials, use the
manual feeding in tray.
• An incorrect type of paper is being used. Use only paper that meets the specifications required by the machine.
• There may be debris inside the machine. Open the front cover and remove any debris.
Envelopes skew or fail to feed correctly.
Ensure that the paper guides are against both sides of the envelopes.
6. Troubleshooting
250
Power and cable connecting problems
1
Power
Click this link to open an animation about solving power problems.
Condition
The machine is not receiving power,
or the connection cable between the
computer and the machine is not
connected properly.
Suggested solutions
• Connect the machine to the electricity supply first. If the machine has a
(Power/Wakeup) button on the control,
press it.
• Disconnect the machine’s cable and reconnect it.
6. Troubleshooting
251
Printing problems
Condition
The machine does not
print.
Possible cause
The machine is not receiving power.
Suggested solutions
Connect the machine to the electricity supply first. If the machine has a
(Power/
Wakeup) button on the control, press it.
The machine is not selected as the default
machine.
Select your machine as your default machine in Windows.
Check the machine for the following:
• The cover is not closed. Close the cover.
• Paper is jammed. Clear the paper jam (see "Clearing paper jams" on page 91).
• No paper is loaded. Load paper (see "Loading paper in the tray" on page 39).
• The toner cartridge is not installed. Install the toner cartridge (see "Toner cartridge" on page 73).
• Make sure the protect cover and sheets are removed from the toner cartridge (see "Toner cartridge" on page 73).
If a system error occurs, contact your service representative.
The connection cable between the computer and
the machine is not connected properly.
Disconnect the machine cable and reconnect it (see "Rear view" on page 22).
The connection cable between the computer and
the machine is defective.
If possible, attach the cable to another computer that is working properly and print a job.
You can also try using a different machine cable.
The port setting is incorrect.
Check the Windows printer settings to make sure that the print job is sent to the correct
port. If the computer has more than one port, make sure that the machine is attached to
the correct one.
6. Troubleshooting
252
Printing problems
Condition
The machine does not
print.
Possible cause
Suggested solutions
The machine may be configured incorrectly.
Check the Printing Preferences to ensure that all of the print settings are correct.
The printer driver may be incorrectly installed.
Uninstall and reinstall the machine’s driver.
The machine is malfunctioning.
Check the display message on the control panel to see if the machine is indicating a
system error. Contact a service representative.
The document size is so big that the hard disk
space of the computer is insufficient to access the
print job.
Get more hard disk space and print the document again.
The output tray is full.
Once the paper is removed from the output tray, the machine resumes printing.
The machine selects print
materials from the wrong
paper source.
The paper option that was selected in the
Printing Preferences may be incorrect.
For many software applications, the paper source selection is found under the Paper tab
within the Printing Preferences (see "Opening printing preferences" on page 52).
Select the correct paper source. See the printer driver help screen (see "Using help" on
page 53).
A print job is extremely
slow.
The job may be very complex.
Reduce the complexity of the page or try adjusting the print quality settings.
Half the page is blank.
The page orientation setting may be incorrect.
Change the page orientation in your application (see "Opening printing preferences" on
page 52). See the printer driver help screen (see "Using help" on page 53).
The paper size and the paper size settings do not
match.
Ensure that the paper size in the printer driver settings matches the paper in the tray.Or,
ensure that the paper size in the printer driver settings matches the paper selection in
the software application settings you use (see "Opening printing preferences" on page
52).
6. Troubleshooting
253
Printing problems
Condition
The machine prints, but
the text is wrong,
garbled, or incomplete.
Pages print, but they are
blank.
Possible cause
Suggested solutions
The machine cable is loose or defective.
Disconnect the machine cable and reconnect. Try a print job that you have already
printed successfully. If possible, attach the cable and the machine to another computer
that you know works and try a print job. Finally, try a new machine cable.
The wrong printer driver was selected.
Check the application’s printer selection menu to ensure that your machine is selected.
The software application is malfunctioning.
Try printing a job from another application.
The operating system is malfunctioning.
Exit Windows and reboot the computer. Turn the machine off and back on again.
The toner cartridge is defective or out of toner.
Redistribute the toner, if necessary. If necessary, replace the toner cartridge.
• See "Redistributing toner" on page 71.
• See "Toner cartridge" on page 73.
The file may have blank pages.
Check the file to ensure that it does not contain blank pages.
Some parts, such as the controller or the board,
may be defective.
Contact a service representative.
The machine does not
print PDF files correctly.
Some parts of graphics,
text, or illustrations are
missing.
Incompatibility between the PDF file and the
Acrobat products.
Printing the PDF file as an image may enable the file to print. Turn on Print As Image
from the Acrobat printing options.
The print quality of
photos is not good.
Images are not clear.
The resolution of the photo is very low.
It will take longer to print when you print a PDF file as an image.
Reduce the photo size. If you increase the photo size in the software application, the
resolution will be reduced.
6. Troubleshooting
254
Printing problems
Condition
Possible cause
Suggested solutions
Before printing, the
machine emits vapor near
the output tray.
Using damp paper can cause vapor during
printing.
This is not a problem. Just keep printing.
The machine does not
print special-sized paper,
such as billing paper.
Paper size and paper size setting do not match.
Set the correct paper size in the Custom in Paper tab in Printing Preferences (see
"Opening printing preferences" on page 52).
The printed billing paper
is curled.
The paper type setting does not match.
Change the printer option and try again. Go to Printing Preferences, click Paper tab,
and set type to Thick (see "Opening printing preferences" on page 52).
6. Troubleshooting
255
Printing quality problems
If the inside of the machine is dirty or paper has been loaded improperly, there might be a reduction in print quality. See the table below to clear the problem.
Condition
Light or faded print
Suggested solutions
• If a vertical white streak or faded area appears on the page, the toner supply is low. Install a new toner cartridge (see "Toner
cartridge" on page 73).
• The paper may not meet paper specifications; for example, the paper may be too moist or rough.
• If the entire page is light, the print resolution setting is too low or the toner save mode is on. Adjust the print resolution and turn
the toner save mode off. See the help screen of the printer driver.
• A combination of faded or smeared defects may indicate that the toner cartridge needs cleaning. Clean the inside of your machine
(see "Cleaning the machine" on page 77).
• The surface of the LSU part inside the machine may be dirty. Clean the inside of your machine (see "Cleaning the machine" on page
77). If these steps do not correct the problem, contact a service representative.
The top half of the paper is
printed lighter than the rest of
the paper
The toner might not adhere properly to this type of paper.
• Change the printer option and try again. Go to Printing Preferences, click the Paper tab, and set the paper type to Recycled (see
"Opening printing preferences" on page 52).
6. Troubleshooting
256
Printing quality problems
Condition
Toner specks
Suggested solutions
• The paper may not meet specifications; for example, the paper may be too moist or rough.
• The transfer roller may be dirty. Clean the inside of your machine (see "Cleaning the machine" on page 77).
A aB bC c
A aB bC c
A aB bC c
A aB bC c
A aB bC c
Dropouts
• The paper path may need cleaning. Contact a service representative (see "Cleaning the machine" on page 77).
If faded areas, generally rounded, occur randomly on the page:
• A single sheet of paper may be defective. Try reprinting the job.
A aBb C
A aBb C
A aBb C
A aBb C
A aBb C
• The moisture content of the paper is uneven or the paper has moist spots on its surface. Try a different brand of paper.
• The paper lot is bad. The manufacturing processes can cause some areas to reject toner. Try a different kind or brand of paper.
• Change the printer option and try again. Go to Printing Preferences, click the Paper tab, and set type to Thick (see "Opening
printing preferences" on page 52).
If these steps do not correct the problem, contact a service representative.
White Spots
If white spots appear on the page:
• The paper is too rough and a lot of dirt from paper falls to the inner components within the machine, so the transfer roller may be
dirty. Clean the inside of your machine (see "Cleaning the machine" on page 77).
• The paper path may need cleaning. Clean the inside of your machine (see "Cleaning the machine" on page 77).
If these steps do not correct the problem, contact a service representative.
6. Troubleshooting
257
Printing quality problems
Condition
Vertical lines
Suggested solutions
If black vertical streaks appear on the page:
• The surface (drum part) of the toner cartridge inside the machine has probably been scratched. Remove the toner cartridge and
install a new one (see "Toner cartridge" on page 73).
If white vertical streaks appear on the page:
• The surface of the LSU part inside the machine may be dirty. Clean the inside of your machine (see "Cleaning the machine" on page
77). If these steps do not correct the problem, contact a service representative.
Black or color background
If the amount of background shading becomes unacceptable:
• Change to a lighter weight paper.
• Check the environmental conditions: very dry conditions or a high level of humidity (higher than 80% RH) can increase the amount
of background shading.
• Remove the old toner cartridge and install a new one (see "Toner cartridge" on page 73).
• Thoroughly redistribute the toner (see "Redistributing toner" on page 71).
Toner smear
• Clean the inside of the machine (see "Cleaning the machine" on page 77).
• Check the paper type and quality.
• Remove the toner cartridge and install a new one (see "Toner cartridge" on page 73).
6. Troubleshooting
258
Printing quality problems
Condition
Vertical repetitive defects
Suggested solutions
If marks repeatedly appear on the printed side of the page at even intervals:
• The toner cartridge may be damaged. If you still have the same problem, remove the toner cartridge and, install a new one (see
"Toner cartridge" on page 73).
• Parts of the machine may have toner on them. If the defects occur on the back of the page, the problem will likely correct itself after
a few more pages.
• The fusing assembly may be damaged. Contact a service representative.
Background scatter
A
Background scatter results from bits of toner randomly distributed on the printed page.
• The paper may be too damp. Try printing with a different batch of paper. Do not open packages of paper until necessary so that
the paper does not absorb too much moisture.
• If background scatter occurs on an envelope, change the printing layout to avoid printing over areas that have overlapping seams
on the reverse side. Printing on seams can cause problems.
Or select Thick from the Printing Preferences window (see "Opening printing preferences" on page 52).
• If background scatter covers the entire surface area of a printed page, adjust the print resolution through your software application
or in Printing Preferences (see "Opening printing preferences" on page 52). Ensure the correct paper type is selected. For example:
If Thicker Paper is selected, but Plain Paper actually used, an overcharging can occur causing this copy quality problem.
• If you are using a new toner cartridge, redistribute the toner first (see "Redistributing toner" on page 71).
Toner particles are around bold
characters or pictures
The toner might not adhere properly to this type of paper.
• Change the printer option and try again. Go to Printing Preferences, click the Paper tab, and set the paper type to Recycled (see
"Opening printing preferences" on page 52).
• Ensure the correct paper type is selected. For example: If Thicker Paper is selected, but Plain Paper actually used, an overcharging
can occur causing this copy quality problem.
6. Troubleshooting
259
Printing quality problems
Condition
Suggested solutions
Misformed characters
• If characters are improperly formed and producing hollow images, the paper stock may be too slick. Try different paper.
Page skew
• Ensure that the paper is loaded properly.
A aBb
A aBb C
A aBb C
A aBb C
A aBb C c
Cc
Curl or wave
• Check the paper type and quality.
• Ensure that the guides are not too tight or too loose against the paper stack.
• Ensure that the paper is loaded properly.
• Check the paper type and quality. Both high temperature and humidity can cause paper curl.
• Turn the stack of paper over in the tray. Also try rotating the paper 180° in the tray.
6. Troubleshooting
260
Printing quality problems
Condition
Wrinkles or creases
Suggested solutions
• Ensure that the paper is loaded properly.
• Check the paper type and quality.
• Turn the stack of paper over in the tray. Also try rotating the paper 180° in the tray.
Back of printouts are dirty
• Check for leaking toner. Clean the inside of the machine (see "Cleaning the machine" on page 77).
Solid color or black pages
• The toner cartridge may not be installed properly. Remove the cartridge and reinsert it.
• The toner cartridge may be defective. Remove the toner cartridge and install a new one (see "Toner cartridge" on page 73).
A
• The machine may require repairing. Contact a service representative.
6. Troubleshooting
261
Printing quality problems
Condition
Loose toner
Suggested solutions
• Clean the inside of the machine (see "Cleaning the machine" on page 77).
• Check the paper type and quality.
• Remove the toner cartridge and then, install a new one (see "Toner cartridge" on page 73).
If the problem persists, the machine may require repair. Contact a service representative.
Character voids
Character voids are white areas within parts of characters that should be solid black:
• You may be printing on the wrong surface of the paper. Remove the paper and turn it around.
A
Horizontal stripes
• The paper may not meet paper specifications.
If horizontally aligned black streaks or smears appear:
• The toner cartridge may be installed improperly. Remove the cartridge and reinsert it.
• The toner cartridge may be defective. Remove the toner cartridge and install a new one (see "Toner cartridge" on page 73).
If the problem persists, the machine may require repairing. Contact a service representative.
6. Troubleshooting
262
Printing quality problems
Condition
Curl
Suggested solutions
If the printed paper is curled or paper does not feed into the machine:
• Turn the stack of paper over in the tray. Also try rotating the paper 180° in the tray.
• Change the printer’s paper option and try again. Go to Printing Preferences, click the Paper tab, and set type to Thin (see
"Opening printing preferences" on page 52).
• An unknown image
repetitively appears on a few
sheets
Your machine is probably being used at an altitude of 1,000 m (3,281 ft) or above.The high altitude may affect the print quality, such
as loose toner or light imaging. Change the altitude setting for your machine (see "Altitude adjustment" on page 194).
• Loose toner
• Light print or contamination
occurs
6. Troubleshooting
263
Copying problems
Condition
Suggested solutions
Copies are too light or too dark. Adjust the darkness in copy feature to lighten or darken the backgrounds of copies (see "Changing the settings for each copy" on page
57).
Smears, lines, marks, or spots
appear on copies.
• If the defects are on the original, adjust darkness in copy feature to lighten the background of your copies.
Copy image is skewed.
• Ensure that the original is aligned with the registration guide.
• If there are no defects on the original, clean the scan unit (see "Cleaning the scan unit" on page 81).
• The transfer roller may be dirty. Clean the inside of your machine (see "Cleaning the machine" on page 77).
Blank copies print out.
Ensure that the original is face down on the scanner glass or face up in the document feeder.
If these steps do not correct the problem, contact a service representative.
Image rubs off the copy easily.
• Replace the paper in the tray with paper from a new package.
• In high humidity areas, do not leave paper in the machine for extended periods of time.
Frequent copy paper jams
occur.
• Fan the paper, then turn it over in the tray. Replace the paper in the tray with a fresh supply. Check/adjust the paper guides, if
necessary.
• Ensure that the paper is the proper type and weight (see "Print media specifications" on page 106).
• Check for copy paper or pieces of copy paper remaining in the machine after a paper jam has been cleared.
Toner cartridge produces fewer
copies than expected before
running out of toner.
• Your originals may contain pictures, solids, or heavy lines. For example, your originals may be forms, newsletters, books, or other
documents that use more toner.
• The scanner lid may be left open while copies are being made.
• Turn the machine off and back on.
6. Troubleshooting
264
Scanning problems
Condition
The scanner does not work.
Suggested solutions
• Make sure that you place the original to be scanned face down on the scanner glass, or face up in the document feeder (see
"Loading originals" on page 47).
• There may not be enough available memory to hold the document you want to scan. Try the Prescan function to see if that works.
Try lowering the scan resolution rate.
• Check that the machine printer cable is connected properly.
• Make sure that the machine printer cable is not defective. Switch the printer cable with a known good cable. If necessary, replace
the printer cable.
• Check that the scanner is configured correctly. Check scan setting in the SmarThru Office or the application you want to use to make
certain that the scanner job is being sent to the correct port (for example, USB001).
The unit scans very slowly.
• Check if the machine is printing received data. If so, scan the document after the received data has been printed.
• Graphics are scanned more slowly than text.
• Communication speed slows in scan mode because of the large amount of memory required to analyze and reproduce the scanned
image. Set your computer to the ECP printer mode through BIOS setting. It will help to increase the speed. For details about how
to set BIOS, refer to your computer user’s guide.
6. Troubleshooting
265
Scanning problems
Condition
Suggested solutions
Message appears on your
computer screen:
• There may be a copying or printing job in progress. Try your job again when that job is finished.
• Device can’t be set to the H/W
mode you want.
• The machine printer cable may be improperly connected or the power may be off.
• Port is being used by another
program.
• Ensure that the machine is properly connected and the power is on, then restart your computer.
• Port is disabled.
• The selected port is currently being used. Restart your computer and try again.
• The scanner driver is not installed or the operating environment is not set up properly.
• The USB cable may be improperly connected or the power may be off.
• Scanner is busy receiving or
printing data. When the
current job is completed, try
again.
• Invalid handle.
• Scanning has failed.
6. Troubleshooting
266
Faxing problems
Condition
Suggested solutions
The machine is not working,
there is no display, or the
buttons are not working.
• Unplug the power cord and plug it in again.
No dial tone.
• Check that the phone line is properly connected (see "Rear view" on page 22).
• Ensure that there is power being supplied to the electrical outlet.
• Ensure that the power is turned on.
• Check that the phone socket on the wall is working by plugging in another phone.
The numbers stored in memory
do not dial correctly.
Make sure that the numbers are stored in memory correctly. To check that, print an address book list.
The original does not feed into
the machine.
• Make sure that the paper is not wrinkled and you are inserting it in correctly. Check that the original is the right size, not too thick
or thin.
• Make sure that the document feeder is firmly closed.
• The document feeder rubber pad may need to be replaced. Contact a service representative.
Faxes are not received
automatically.
• The receiving mode should be set to fax (see "Changing the receive modes" on page 230).
• Make sure that there is paper in the tray (see "Print media specifications" on page 106).
• Check to see if the display shows any error message. If it does, clear the problem.
The machine does not send.
• Make sure that the original is loaded in the document feeder or on the scanner glass.
• Check the fax machine you are sending to, to see if it can receive your fax.
The incoming fax has blank
spaces or is of poor-quality.
• The fax machine sending you the fax may be faulty.
• A noisy phone line can cause line errors.
• Check your machine by making a copy.
• A toner cartridge has almost reached its estimated cartridge life. Replace the toner cartridge (see "Toner cartridge" on page 73).
6. Troubleshooting
267
Faxing problems
Condition
Suggested solutions
Some of the words on an
incoming fax are stretched.
The fax machine sending the fax had a temporary document jam.
There are lines on the originals
you sent.
Check your scan unit for marks and clean it (see "Cleaning the scan unit" on page 81).
The machine dials a number,
but the connection with the
other fax machine fails.
The other fax machine may be turned off, out of paper, or cannot answer incoming calls. Speak with the other machine operator and
ask them to solve the problem on their side.
Faxes do not store in memory.
There may not be enough memory space to store the fax. If the display indicating the memory status shows, delete any faxes you no
longer need from the memory, and then try to store the fax again. Call for service.
Blank areas appear at the
bottom of each page or on
other pages, with a small strip
of text at the top.
You may have chosen the wrong paper settings in the user option setting. Check the paper size and type again.
6. Troubleshooting
268
Operating system problems
2
Common Windows problems
Condition
Suggested solutions
“File in Use” message appears
during installation.
Exit all software applications. Remove all software from the startup group, then restart Windows. Reinstall the printer driver.
“General Protection Fault”,
“Exception OE”, “Spool 32”, or
“Illegal Operation” messages
appear.
Close all other applications, reboot Windows and try printing again.
“Fail To Print”, “A printer
timeout error occurred”
message appear.
These messages may appear during printing. Just keep waiting until the machine finishes printing. If the message appears in ready
mode or after printing has completed, check the connection and/or whether an error has occurred.
Refer to the Microsoft Windows User’s Guide that came with your computer for further information on Windows error messages.
6. Troubleshooting
269
Operating system problems
3
Common Mac problems
Condition
The machine does not print PDF files
correctly. Some parts of graphics, text, or
illustrations are missing.
Suggested solutions
Printing the PDF file as an image may enable the file to print. Turn on Print As Image from the Acrobat printing options.
It will take longer to print when you print a PDF file as an image.
Some letters are not displayed normally
during cover page printing.
Mac OS cannot create the font while printing the cover page. The English alphabet and numbers are displayed normally on
the cover page.
When printing a document in Mac with
Acrobat Reader 6.0 or higher, colors
print incorrectly.
Make sure that the resolution setting in your machine driver matches the one in Acrobat Reader.
Refer to the Mac User’s Guide that came with your computer for further information on Mac error messages.
6. Troubleshooting
270
Operating system problems
4
Common Linux problems
Condition
Suggested solutions
There is no xsane nor simplescan application on my Linux
machine.
• For some Linux distributions, there might be no default scan application. To use scan features, install one of scan applications using
download center supplied by O/S (ex. Ubuntu Software Center for Ubuntu, Install/Remove Software for openSUSE, Software
for Fedora).
Scanner can not be found via
network.
For some Linux distributions, strong firewall is enabled and it may block our installer from opening necessary port for searching
network devices. In such case, open snmp port - 22161 manually or disable the firewall temporarily while using the device.
Printing with more than two
copies does not work.
The problem occurs on Ubuntu 12.04 due to problem in standard CUPS filter 'pdftops' (actual output point it out exactly) and it has
been fixed already. Updating 'cups-filters' package from version 1.0.17 to version 1.0.18 fixes the problem ('pdftops' is a part of 'cupsfilters' package).
Printing PDF files does not
work.
The problem occurs on openSUSE 12.3 and it has some problem in standard CUPS filter 'pdftops' that may affect certain PDF
documents (it seems this issue relates somehow to fonts used in PDF). Due to this problem, incorrect Postscript is generated and
device fails to print it. We are waiting for the patch.
Unchecking collate option in
Print dialog does not work.
For some distributions, GNOME Print Dialog has an issue handling collate option. As workaround, set the default value of collate option
to 'False' using system's Printing utility(execute "system-config-printer" in Terminal program).
Printing always works with
duplex.
This duplex issue was in Ubuntu 9.10 cups package and was already fixed in security updates for this package, starting from cups
version 1.4.1-5ubuntu2.2.
Refer to the Linux User’s Guide that came with your computer for further information on Linux error messages.
6. Troubleshooting
271
Operating system problems
5
Common PostScript problems
The following situations are PS language specific and may occur when several printer languages are used.
Problem
The PostScript file cannot be
printed
Possible cause
The PostScript driver may not be installed
correctly.
Solution
• Install the PostScript driver (see "Software Installation" on page 130).
• Print a configuration page and verify that the PS version is available for
printing.
• If the problem persists, contact a service representative.
Limit Check Error report prints
The print job was too complex.
You might need to reduce the complexity of the page or install more memory.
A PostScript error page prints
The print job may not be PostScript.
Make sure that the print job is a PostScript job. Check to see whether the software
application expected a setup or PostScript header file to be sent to the machine.
The optional tray is not
selected in the driver
The printer driver has not been configured to
recognize the optional tray.
Open the PostScript driver properties, select the Device Options tab, and set the
tray option.
When printing a document in
Mac with Acrobat Reader 6.0 or
higher, colors print incorrectly
The resolution setting in the printer driver may
not be matched with the one in Acrobat Reader.
Make sure that the resolution setting in your printer driver matches the one in
Acrobat Reader.
6. Troubleshooting
272
Quick Guide for Windows 8
User
This chapter will outline features specific to the Windows 8 OS. This chapter applies to users running Windows 8.
• Understanding the screen
274
• System requirements
275
• Installing the driver locally
276
• Installing the driver over the network
278
• Installing the driver over the wireless network
280
• Uninstalling the driver
282
• Using Samsung Printer Experience
283
• Accessing management tools
290
• Installing accessories
291
• Troubleshooting
292
• The screen may appear somewhat different depending on the model or interface in use.
• Since this guide has been prepared based on Windows 8, some of the instructions may differ
depending on the version. It may also be modified without prior notice.
Understanding the screen
Windows 8 provides both the new Start screen mode and the Desktop screen mode of the existing OS.
Start Screen
Desktop Screen
Quick Guide for Windows 8 User
274
System requirements
Requirement (recommended)
Operating
system
Windows® 8
CPU
Intel® Pentium® IV 1 GHz 32-bit
or 64-bit processor or higher
RAM
1 GB (2 GB)
Free HDD
Space
16 GB
• Support for DirectX® 9 graphics with 128 MB memory (to
enable the Aero theme).
• DVD-R/W Drive
Quick Guide for Windows 8 User
275
Installing the driver locally
A locally connected machine is a machine directly attached to your computer
using the cable.
• If you want to install Samsung’s printer management tools, you need to
install them using the supplied software CD (see "From the Desktop
Screen" on page 276).
• Only use a USB cable no longer than 3 meters (118 inches).
• You can download Samsung Printer Experience app from the Windows
Store. You need have a Microsoft account to use the Windows Store.
1 From Charms, select Search.
2 Click Store.
3 Search and click Samsung Printer Experience.
4 Click Install.
• The V4 driver is automatically downloaded from the Windows Update if
your computer is connected to the Internet. If not, you can manually
download the V4 driver from Samsung website, www.samsung.com >
find your product > Support or downloads.
• If you install the driver using the supplied software CD, V4 driver is not
installed. If you want to use the V4 driver in the Desktop screen, you can
download from the Samsung website, www.samsung.com >find your
product > Support or downloads.
2
From the Desktop Screen
1
From the Start Screen
1
Make sure that your computer is connected to the Internet and powered
on.
2
3
Make sure that the machine is powered on.
If you install the driver using the supplied software CD, you cannot use the
installed driver from the Start screen.
Connect the computer and the machine with a USB cable.
The driver is automatically installed from the Windows Update.
Quick Guide for Windows 8 User
276
Installing the driver locally
1
Insert the supplied software CD into your CD-ROM drive.
If the installation window does not appear, from Charms, select Search
> Apps and search for Run. Type in X:\Setup.exe, replacing “X” with the
letter that represents your CD-ROM drive and click OK.
If “Tap to choose what happens with this disc.” pop-up window appears,
click the window and select Run Setup.exe.
2
Review and accept the installation agreements in the installation
window. Then, click Next.
3
Select USB connection on the Printer Connection Type screen. Then,
click Next.
4
Follow the instructions in the installation window.
Quick Guide for Windows 8 User
277
Installing the driver over the network
• Some features and optional goods may not be available depending on
model or country (see "Features by models" on page 7).
• You can print a Network Configuration Report from the machine’s
control panel that will show the current machine’s host name (see
"Printing a network configuration report" on page 166).
• Machine that do not support networking will not be able to use this
feature (see "Rear view" on page 22).
• If you want to install Samsung’s printer management tools, you need to
install them using the supplied software CD (see "From the Desktop
Screen" on page 276).
• Samsung Printer Experience app can only be used in the Start screen
when V4 driver is installed. The V4 driver is automatically downloaded
from the Windows Update if your computer is connected to the Internet.
If not, you can manually download the V4 driver from Samsung website,
www.samsung.com >find your product > Support or downloads.
• You can download Samsung Printer Experience app from the Windows
Store. You need have a Microsoft account to use the Windows Store.
1 From Charms, select Search.
2 Click Store.
3 Search and click Samsung Printer Experience.
4 Click Install.
• If you install the driver using the supplied software CD, V4 driver is not
installed. If you want to use the V4 driver in the Desktop screen, you can
download from the Samsung website, www.samsung.com >find your
product > Support or downloads.
5
The driver is automatically installed from the Windows Update.
3
From the Start Screen
4
From the Desktop Screen
1
2
3
Make sure that the machine is connected to the network and powered
on. Also, your machine’s IP address should have been set (see "Setting IP
address" on page 137).
If you install the driver using the supplied software CD, you cannot use the
installed driver from the Start screen.
From Charms, select Settings > Change PC settings > Devices.
Click Add a device.
Discovered machines will be shown on the screen.
4
Click the model name or host name you wish to use.
Quick Guide for Windows 8 User
278
Installing the driver over the network
1
Make sure that the machine is connected to the network and powered
on. Also, your machine’s IP address should have been set (see "Setting IP
address" on page 137).
2
Insert the supplied software CD into your CD-ROM drive.
If the installation window does not appear, from Charms, select Search
> Apps and search for Run. Type in X:\Setup.exe, replacing “X” with the
letter that represents your CD-ROM drive and click OK.
If “Tap to choose what happens with this disc.” pop-up window appears,
click the window and select Run Setup.exe.
3
Review and accept the installation agreements in the installation
window. Then, click Next.
4
5
Select Network connection on the Printer Connection Type screen.
Follow the instructions in the installation window.
Quick Guide for Windows 8 User
279
Installing the driver over the wireless network
• Samsung Printer Experience app can only be used in the Start screen
when V4 driver is installed. The V4 driver is automatically downloaded
from the Windows Update if your computer is connected to the Internet.
If not, you can manually download the V4 driver from Samsung website,
www.samsung.com >find your product > Support or downloads.
You can print a Network Configuration Report from the machine’s control
panel that will show the current machine’s host name (see "Printing a
network configuration report" on page 166).
• If you install the driver using the supplied software CD, V4 driver is not
installed. If you want to use the V4 driver in the Desktop screen, you can
download from the Samsung website, www.samsung.com >find your
product > Support or downloads.
5
The driver is automatically installed from the Windows Update.
• If you want to install Samsung’s printer management tools, you need to
install them using the supplied software CD (see "From the Desktop
Screen" on page 276).
• You must set up for wireless network using the supplied software CD in
Desktop screen mode.
• You can download Samsung Printer Experience app from the Windows
Store. You need have a Microsoft account to use the Windows Store.
1 From Charms, select Search.
2 Click Store.
3 Search and click Samsung Printer Experience.
4 Click Install.
• If you are using a computer without a CD-ROM, you can set up the
wireless network from the machine’s control panel (see "Wireless
network setup" on page 148).
5
From the Start Screen
6
1
After completing the wireless network connection, you need to install a
machine driver to print from an application.
2
3
From Charms, select Settings > Change PC settings > Devices.
Click Add a device.
From the Desktop Screen
If you install the driver using the supplied software CD, you cannot use the
installed driver from the Start screen.
Discovered machines will be shown on the screen.
4
Click the model name or host name you wish to use.
Quick Guide for Windows 8 User
280
Installing the driver over the wireless network
1
2
Turn on your computer, access point, and machine.
Insert the supplied software CD into your CD-ROM drive.
If the installation window does not appear, from Charms, select Search
> Apps and search for Run. Type in X:\Setup.exe, replacing “X” with the
letter that represents your CD-ROM drive and click OK.
If “Tap to choose what happens with this disc.” pop-up window appears,
click the window and select Run Setup.exe.
3
Review and accept the installation agreements in the installation
window. Then, click Next.
4
Follow the instructions in the installation window.
For wireless set up or driver installation, refer to the wireless network setup
chapter (see "Wireless network setup" on page 148).
Quick Guide for Windows 8 User
281
Uninstalling the driver
7
From the Start Screen
1
Make sure that the machine is connected to your computer and
powered on.
2
Click on the Uninstall Samsung Printer Software tile in the Start
screen.
3
Follow the instructions in the window.
5
Follow the instructions in the window.
• If you cannot find a Samsung Printer Software tile, unintstall from the
desktop screen mode (see "From the Desktop Screen" on page 282).
• If you want to uninstall Samsung’s printer management tools, from the
Start screen, right-click the app > Uninstall > right-click the program
you want to delete > Uninstall and follow the instruction in the window.
8
From the Desktop Screen
1
2
3
4
From Charms, select Search > Apps.
Search and click Control Panel.
Click Programs and Features.
Right-click the driver you want to uninstall and select Uninstall.
Quick Guide for Windows 8 User
282
Using Samsung Printer Experience
Samsung Printer Experience is a Samsung application that combines
Samsung machine settings and machine management into one location. You
can set device settings, order supplies, open troubleshooting guides, visit
Samsung’s web site, and check connected machine information. This
application will be automatically downloaded from the Windows Store if the
machine is connected to a computer with an Internet connection.
The screenshot may differ depending on the model you are using.
9
Understanding the Samsung Printer Experience
To open the application,
From the Start screen, select the Samsung Printer Experience (
) tile.
The Samsung Printer Experience interface comprises various useful features as
described in the following table:
1
Printer
Information
This area gives you general information about your
machine. You can check information, such as the
machine’s status, location, IP address, and remaining
toner level.
Quick Guide for Windows 8 User
283
Using Samsung Printer Experience
10
2
User Guide
You can view the online User’s Guide. You need to be
connected to the Internet to use this feature.
This button opens the Troubleshooting Guide
when an error occurs. You can directly open the
troubleshooting section in the user’s guide.
Adding/Deleting Printers
If you do not have any printer added to the Samsung Printer Experience, or if
you want to add/delete a printer, follow the instructions below.
You can only add/delete network connected printers.
Order Supplies
3
4
Visit Samsung
Printer Settings
5
6
Device List &
Latest Scanned
Image
Click on this button to order replacement toner
cartridges online. You need to be connected to the
Internet to use this feature.
Links to Samsung printer website. You need to be
connected to the Internet to use this feature.
You can configure various machine settings such as
machine setup, paper, layout, emulation, networking,
and print information through SyncThru™ Web Service.
Your machine needs to be connected to a network. This
button will be disabled if your machine is connected via
USB cable.
The scan list displays devices that supports Samsung
Printer Experience. Under the device, you can see the
latest scanned images. Your machine needs to be
connected to a network to scan from here. This section is
for the users with multi-functional printers.
Adding a printer
1
From the Charms, select Settings.
Or, right-click the Samsung Printer Experience page and select
Settings.
2
3
Select Add Printer
Select the printer you want to add.
You can see the added printer.
If you see
mark, you can also click
mark to add printers.
Quick Guide for Windows 8 User
284
Using Samsung Printer Experience
Deleting a printer
1
4
5
From the Charms, select Settings.
Select the printer settings, such as the number of copies and orientation.
Click the Print button to start the print job.
Or, right-click the Samsung Printer Experience page and select
Settings.
2
3
4
Select Remove Printer
Select the printer you want to delete.
Click Yes.
You can see that the deleted printer is removed from the screen.
11
Printing from Windows 8
This section explains common printing tasks from the Start screen.
Basic printing
1
2
3
Open the document to print.
Cancelling a print job
If the printing job is waiting in the print queue or print spooler, cancel the job as
follows:
•
(
From the Charms, select Devices.
Select your printer from the list
You can access this window by simply double-clicking the machine icon
•
) in the Windows task bar.
You can also cancel the current job by pressing
(Cancel or Stop/Clear)
button on the control panel.
Quick Guide for Windows 8 User
285
Using Samsung Printer Experience
Opening more settings
Basic tab
The screen may appear somewhat different depending on the model or
options.
You can set up more printing parameters.
1
2
3
4
Open the document you want to print.
From the Charms, select Devices.
Select your printer from the list
Click More settings.
Basic
This option allows you to choose the basic printing settings such as copies,
orientation, and document type.
Eco settings
This option allows you to choose multiple pages per side to save media.
Quick Guide for Windows 8 User
286
Using Samsung Printer Experience
Advanced tab
Security tab
Some features may not be available depending on the model or options. If
this tab is not shown or disabled, it means that this features are not
supported.
Paper settings
This option allows you to set the basic paper handling specifications.
Layout settings
This option allows you to set the various ways to layout your documents.
Job Accounting
This option allows you to print with the given permission.
Confidential Printing
Quick Guide for Windows 8 User
287
Using Samsung Printer Experience
This option is used for printing confidential documents. You need to enter a
password to print using it.
Scanning with your machine lets you turn pictures and text into digital files that
can be stored on your computer.
Using the sharing feature
Scanning from Samsung Printer Experience
Samsung Printer Experience allows you to print from other applications
installed on the computer using the sharing feature.
The most frequently used printing menus are displayed for quick scanning.
This feature is only available for printing jpeg, bmp, tiff, gif, and png file
formats.
1
2
3
4
Select the content you want to print from other application.
From the Charms, select Share > Samsung Printer Experience .
Select the printer settings, such as the number of copies and orientation.
Click the Print button to start the print job.
1
Place a single document face down on the document glass, or load the
documents face up into the document feeder.
2
3
4
Click the Samsung Printer Experience tile on the Start screen.
5
6
Click Prescan (
7
Click Scan (
Click Scan (
).
Set up the scanning parameters such as image type, document size, and
resolution.
) to check the image.
Adjust the prescanned image with scanning operation functions such as
rotate and mirror.
12
Scanning from Windows 8
) and save the image.
This section is for the users with multi-functional printers.
Quick Guide for Windows 8 User
288
Using Samsung Printer Experience
• When you place the originals in the ADF (or DADF), Prescan (
available.
) is not
• You can skip step 5, if the Prescan option is selected.
Quick Guide for Windows 8 User
289
Accessing management tools
Samsung provides a variety of management tools for Samsung printers. For
more information on each tool, refer to "Useful Management Tools" on page
236.
1
2
3
4
From the Charms, select Search > Apps.
Find Samsung Printers.
Under Samsung Printers, you can see installed management tools.
Click the management tool you want to use.
After installing the driver, for some management tools, you can access them
directly from the Start screen by clicking on the corresponding tile.
Quick Guide for Windows 8 User
290
Installing accessories
When you install optional devices, such as optional tray, memory, etc, this
machine automatically detects and sets the optional devices. If you cannot use
the optional devices you installed in this driver, you can set the optional devices
in Device Settings to use.
1
2
3
From the Charms, select Search > Settings.
Search for Devices and Printers.
Right-click on your printer icon and select Printer properties.
If Printer properties item has a▶mark, you can select other printer drivers
connected with the selected printer.
4
Select Device Settings.
The Printer properties window may differ depending on the driver or
operating system you are using.
5
6
Select the appropriate option.
Click OK until you exit the Printer properties window.
Quick Guide for Windows 8 User
291
Troubleshooting
Problem
Suggested Solutions
Samsung Printer
Experience is not shown
when you click more
settings.
Samsung Printer Experience is not installed.
Download the app. from the Windows Store and
install it.
Machine information is
not displayed when you
click the device in the
Devices and Printers.
Check the Printer properties. Click the Ports tab.
The error related toast
message pops up.
(Control Panel > Devices and Printers > Right-click
on your printer icon and select Printer properties)
If the port is set to File or LPT, uncheck them and
select TCP/IP, USB, or WSD.
Quick Guide for Windows 8 User
292
Contact SAMSUNG worldwide
If you have any comments or questions regarding Samsung products, contact
the Samsung customer care center.
Country/Region
Customer Care Center
WebSite
0800 100 100
www.samsung.com/
n_africa
ANGOLA
91-726-7864
www.samsung.com
ARGENTINA
0800-333-3733
www.samsung.com.ar
ALGERIA
ARMENIA
0-800-05-555
www.samsung.com
AUSTRALIA
1300 362 603
www.samsung.com/au
AUSTRIA
0810-SAMSUNG (7267864, €
0.07/min)
www.samsung.com
AZERBAIJAN
088-55-55-555
www.samsung.com
8000-4726
www.samsung.com/ae
(English)
Country/Region
Customer Care Center
BOSNIA
051 133 1999
www.samsung.com
BOTSWANA
8007260000
www.samsung.com
0800-124-421 (Demais cidades e
regiões)
www.samsung.com.br
BRAZIL
4004-0000 (Capitais e grandes
centros)
BULGARIA
07001 33 11 , share cost tariff
www.samsung.com/bg
BURUNDI
200
www.samsung.com
7095- 0077
www.samsung.com/
africa_fr/
1-800-SAMSUNG (726-7864)
www.samsung.com/ca
(English)
CAMEROON
CANADA
BAHRAIN
BELARUS
www.samsung.com/
ae_ar (Arabic)
810-800-500-55-500
www.samsung.com
02-201-24-18
www.samsung.com/be
(Dutch)
BELGIUM
BOLIVIA
www.samsung.com/
be_fr (French)
800-10-7260
WebSite
CHILE
CHINA
COLOMBIA
www.samsung.com/
ca_fr (French)
800-SAMSUNG (726-7864)
www.samsung.com/cl
[HHP] 02-24828200
400-810-5858
www.samsung.com
01-8000112112
www.samsung.com/co
Bogotá: 6001272
www.samsung.com
Contact SAMSUNG worldwide
293
Contact SAMSUNG worldwide
Country/Region
Customer Care Center
0-800-507-7267
COSTA RICA
CROATIA
Cote D’ Ivoire
WebSite
www.samsung.com/
latin (Spanish)
www.samsung.com/
latin_en (English)
Customer Care Center
800-6225
WebSite
www.samsung.com/
latin (Spanish)
EL SALVADOR
www.samsung.com/
latin_en (English)
062 SAMSUNG (062 726 786)
www.samsung.com/hr
ESTONIA
800-7267
www.samsung.com/ee
8000 0077
www.samsung.com/
africa_fr/
FINLAND
030-6227 515
www.samsung.com
FRANCE
01 48 63 00 00
www.samsung.com/fr
0180 6 SAMSUNG bzw.
www.samsung.com
CYPRUS
8009 4000 only from landline
www.samsung.com/gr
CZECH
800-SAMSUNG (800-726786)
www.samsung.com
DENMARK
70 70 19 70
www.samsung.com
1-800-751-2676
www.samsung.com/
latin (Spanish)
DOMINICA
DRC
Country/Region
www.samsung.com/
latin_en (English)
499999
0180 6 7267864*
GERMANY
0180 6 67267864* (*0,20 €/Anruf
aus dem dt. Festnetz, aus dem
Mobilfunk max. 0,60 €/Anruf)
GEORGIA
www.samsung.com
GHANA
1-800-10-7267
ECUADOR
www.samsung.com/
latin (Spanish)
www.samsung.com/
latin_en (English)
EGYPT
08000-726786
www.samsung.com
EIRE
0818 717100
www.samsung.com
[HHP] 0180 6 M SAMSUNG bzw.
GREECE
8-800-555-555
www.samsung.com
0800-10077
www.samsung.com/
africa_en/
0302-200077
80111-SAMSUNG (80111 726
7864) only from land line(+30)
210 6897691 from mobile and
land line
www.samsung.com/gr
Contact SAMSUNG worldwide
294
Contact SAMSUNG worldwide
Country/Region
Customer Care Center
1-800-299-0013
GUATEMALA
800-27919267
HONDURAS
HONG KONG
INDIA
INDONESIA
IRAN
ITALIA
JAMAICA
Country/Region
www.samsung.com/
latin (Spanish)
JAPAN
www.samsung.com/
latin_en (English)
JORDAN
www.samsung.com/
latin (Spanish)
www.samsung.com/hk
(Chinese)
www.samsung.com/
hk_en (English)
06-80-SAMSUNG (726-7864)
www.samsung.com/hu
1800 3000 8282
www.samsung.com/in
1800 266 8282
0800-112-8888 (Toll Free)
www.samsung.com/id
Customer Care Center
0120-327-527
www.samsung.com
800-22273
www.samsung.com/
Levant (English)
065777444
8-10-800-500-55-500 (GSM:7799) www.samsung.com
KENYA
0800 545 545
www.samsung.com
183-2255 (183-CALL)
www.samsung.com/ae
(English)
KUWAIT
www.samsung.com/
ae_ar (Arabic)
KYRGYZSTAN
00-800-500-55-500
www.samsung.com
LATVIA
8000-7267
www.samsung.com/lv
LITHUANIA
8-800-77777
www.samsung.com/lt
LUXEMBURG
261 03 710
www.samsung.com
1800-88-9999
www.samsung.com/
my
MEXICO
01-800-SAMSUNG (726-7864)
www.samsung.com
MOLDOVA
0-800-614-40
www.samsung.com
MONGOLIA
+7-800-555-55-55
www.samsung.com
MONTENEGRO
020 405 888
www.samsung.com
MOROCCO
080 100 2255
www.samsung.com
MALAYSIA
021-5699-7777
021-8255
www.samsung.com
800-SAMSUNG (726-7864)
www.samsung.com
[HHP] 800.Msamsung
(800.67267864)
1-800-234-7267
www.samsung.com
WebSite
KAZAKHSTAN
www.samsung.com/
latin_en (English)
(852) 3698-4698
HUNGARY
WebSite
Contact SAMSUNG worldwide
295
Contact SAMSUNG worldwide
Country/Region
Customer Care Center
WebSite
MOZAMBIQUE
847267864 / 827267864
www.samsung.com
NAMIBIA
08 197 267 864
www.samsung.com
0800-726-7864
www.samsung.com/
africa_en/
0900-SAMSUNG (0900-7267864)
(€ 0,10/min)
www.samsung.com
0800 SAMSUNG (0800 726 786)
www.samsung.com/nz
00-1800-5077267
www.samsung.com/
latin (Spanish)
NIGERIA
NETHERLANDS
NEW ZEALAND
Country/Region
PARAGUAY
PERU
Customer Care Center
009 800 542 0001
www.samsung.com.py
0-800-777-08
www.samsung.com/pe
Desde celulares por favor llamar
al número 336 8686
1-800-10-7267864 [PLDT]
PHILIPPINES
WebSite
www.samsung.com/ph
1-800-8-7267864 [Globe landline
and Mobile]
02-4222111 [Other landline]
NICARAGUA
NORWAY
www.samsung.com/
latin_en (English)
www.samsung.com
800-SAMSUNG (726-7864)
www.samsung.com/ae
(English)
* (całkowity koszt połączenia jak
za 1 impuls według taryfy
operatora)
www.samsung.com/
ae_ar (Arabic)
** (koszt połączenia według
taryfy operatora)
0800-Samsung (72678)
800-7267
PANAMA
www.samsung.com/
pk/
POLAND
PORTUGAL
808 20-SAMSUNG (808 20 7267)
www.samsung.com
PUERTO RICO
1-800-682-3180
www.samsung.com
800-2255 (800-CALL)
www.samsung.com/ae
(English)
www.samsung.com/
latin (Spanish)
www.samsung.com/
latin_en (English)
www.samsung.com/pl
[HHP] 0 801-672-678* lub +48 22
607-93-33**
815-56 480
OMAN
PAKISTAN
0 801-1SAMSUNG(172-678) * lub
+48 22 607-93-33 **
QATAR
www.samsung.com/
ae_ar (Arabic)
Contact SAMSUNG worldwide
296
Contact SAMSUNG worldwide
Country/Region
Customer Care Center
WebSite
Country/Region
Customer Care Center
WebSite
RWANDA
9999
www.samsung.com
TADJIKISTAN
8-10-800-500-55-500
www.samsung.com
ROMANIA
08008 SAMSUNG (08008 726
7864)TOLL FREE No.
www.samsung.com/ro
TAIWAN
0800-329-999
www.samsung.com/tw
TANZANIA
0685 88 99 00
www.samsung.com
800-00-0077
www.samsung.com
1800-29-3232
www.samsung.com/th
9200-21230
www.samsung.com/sa
(Arabic)
8-800-555-55-55
www.samsung.com/
africa_fr/
SERBIA
011 321 6899
www.samsung.com/rs
SINGAPORE
1800-SAMSUNG (726-7864)
www.samsung.com/sg
SLOVAKIA
0800 - SAMSUNG(0800-726 786)
www.samsung.com
SOUTH AFRICA
0860 SAMSUNG (726-7864)
www.samsung.com
SPAIN
902-1-SAMSUNG(902 172 678)
SUDAN
RUSSIA
SAUDI ARABIA
THAILAND
02-689-3232
TRINIDAD &
TOBAGO
1-800-SAMSUNG (726-7864)
www.samsung.com
TURKEY
444 77 11
www.samsung.com
U.A.E
800-SAMSUNG (726-7864)
www.samsung.com
U.K
0330 SAMSUNG (726-7864)
www.samsung.com
U.S.A
1-800-SAMSUNG (726-7864)
www.samsung.com/us
www.samsung.com
U.S.A (Mobile
Phones)
[HHP] 1-888-987-HELP(4357)
www.samsung.com
1969
www.samsung.com
UGANDA
0800 300 300
www.samsung.com
SWEDEN
0771 726 7864 (SAMSUNG)
www.samsung.com
0-800-502-000
www.samsung.com/ch
SWITZERLAND
0848-SAMSUNG (7267864, CHF
0.08/min)
www.samsung.com/ua
(Ukrainian)
18252273
www.samsung.com/
Levant (English)
SENEGAL
SYRIA
UKRAINE
www.samsung.com/
ua_ru (Russian)
www.samsung.com/
ch_fr/
URUGUAY
000 405 437 33
www.samsung.com
UZBEKISTAN
8-10-800-500-55-500
www.samsung.com
Contact SAMSUNG worldwide
297
Contact SAMSUNG worldwide
Country/Region
Customer Care Center
WebSite
VENEZUELA
0-800-100-5303
www.samsung.com/ve
VIETNAM
1 800 588 889
www.samsung.com
ZAMBIA
0211 350370
www.samsung.com
Contact SAMSUNG worldwide
298
Glossary
ADF
The following glossary helps you get familiar with the product by
understanding the terminologies commonly used with printing as well as
mentioned in this user’s guide.
802.11
802.11 is a set of standards for wireless local area network (WLAN)
communication, developed by the IEEE LAN/MAN Standards Committee (IEEE
802).
802.11b/g/n
802.11b/g/n can share same hardware and use the 2.4 GHz band. 802.11b
supports bandwidth up to 11 Mbps, 802.11n supports bandwidth up to 150
Mbps. 802.11b/g/n devices may occasionally suffer interference from
microwave ovens, cordless telephones, and Bluetooth devices.
An Automatic Document Feeder (ADF) is a scanning unit that will automatically
feed an original sheet of paper so that the machine can scan some amount of the
paper at once.
AppleTalk
AppleTalk is a proprietary suite of protocols developed by Apple, Inc for
computer networking. It was included in the original Mac (1984) and is now
deprecated by Apple in favor of TCP/IP networking.
BIT Depth
A computer graphics term describing the number of bits used to represent the
color of a single pixel in a bitmapped image. Higher color depth gives a broader
range of distinct colors. As the number of bits increases, the number of possible
colors becomes impractically large for a color map. 1-bit color is commonly
called as monochrome or black and white.
Access point
Access Point or Wireless Access Point (AP or WAP) is a device that connects
wireless communication devices together on wireless local area networks
(WLAN), and acts as a central transmitter and receiver of WLAN radio signals.
BMP
A bitmapped graphics format used internally by the Microsoft Windows
graphics subsystem (GDI), and used commonly as a simple graphics file format
on that platform.
Glossary
299
Glossary
BOOTP
Coverage
Bootstrap Protocol. A network protocol used by a network client to obtain its IP
address automatically. This is usually done in the bootstrap process of
computers or operating systems running on them. The BOOTP servers assign
the IP address from a pool of addresses to each client. BOOTP enables 'diskless
workstation' computers to obtain an IP address prior to loading any advanced
operating system.
It is the printing term used for a toner usage measurement on printing. For
example, 5% coverage means that an A4 sided paper has about 5% image or text
on it. So, if the paper or original has complicated images or lots of text on it, the
coverage will be higher and at the same time, a toner usage will be as much as
the coverage.
CSV
CCD
Charge Coupled Device (CCD) is a hardware which enables the scan job. CCD
Locking mechanism is also used to hold the CCD module to prevent any damage
when you move the machine.
Comma Separated Values (CSV). A type of file format, CSV is used to exchange
data between disparate applications. The file format, as it is used in Microsoft
Excel, has become a de facto standard throughout the industry, even among
non-Microsoft platforms.
Collation
DADF
Collation is a process of printing a multiple-copy job in sets. When collation is
selected, the device prints an entire set before printing additional copies.
A Duplex Automatic Document Feeder (DADF) is a scanning unit that will
automatically feed and turn over an original sheet of paper so that the machine
can scan on both sides of the paper.
Control Panel
Default
A control panel is a flat, typically vertical, area where control or monitoring
instruments are displayed. They are typically found in front of the machine.
The value or setting that is in effect when taking a printer out of its box state,
reset, or initialized.
Glossary
300
Glossary
DHCP
DPI
A Dynamic Host Configuration Protocol (DHCP) is a client-server networking
protocol. A DHCP server provides configuration parameters specific to the DHCP
client host requesting, generally, information required by the client host to
participate on an IP network. DHCP also provides a mechanism for allocation of
IP addresses to client hosts.
Dots Per Inch (DPI) is a measurement of resolution that is used for scanning and
printing. Generally, higher DPI results in a higher resolution, more visible detail
in the image, and a larger file size.
DIMM
Distinctive Ring Pattern Detection. Distinctive Ring is a telephone company
service which enables a user to use a single telephone line to answer several
different telephone numbers.
Dual Inline Memory Module (DIMM), a small circuit board that holds memory.
DIMM stores all the data within the machine like printing data, received fax data.
DRPD
Duplex
DLNA
The Digital Living Network Alliance (DLNA) is a standard that allows devices on
a home network to share information with each other across the network.
A mechanism that will automatically turn over a sheet of paper so that the
machine can print (or scan) on both sides of the paper. A printer equipped with
a Duplex Unit can print on both sides of paper during one print cycle.
DNS
Duty Cycle
The Domain Name Server (DNS) is a system that stores information associated
with domain names in a distributed database on networks, such as the Internet.
Duty cycle is the page quantity which does not affect printer performance for a
month. Generally the printer has the lifespan limitation such as pages per year.
The lifespan means the average capacity of print-outs, usually within the
warranty period. For example, if the duty cycle is 48,000 pages per month
assuming 20 working days, a printer limits 2,400 pages a day.
Dot Matrix Printer
A dot matrix printer refers to a type of computer printer with a print head that
runs back and forth on the page and prints by impact, striking an ink-soaked
cloth ribbon against the paper, much like a typewriter.
Glossary
301
Glossary
ECM
EtherTalk
Error Correction Mode (ECM) is an optional transmission mode built into Class 1
fax machines or fax modems. It automatically detects and corrects errors in the
fax transmission process that are sometimes caused by telephone line noise.
A suite of protocols developed by Apple Computer for computer networking. It
was included in the original Mac (1984) and is now deprecated by Apple in favor
of TCP/IP networking.
Emulation
FDI
Emulation is a technique of one machine obtaining the same results as another.
Foreign Device Interface (FDI) is a card installed inside the machine to allow a
third party device such as a coin operated device or a card reader. Those devices
allow the pay-for-print service on your machine.
An emulator duplicates the functions of one system with a different system, so
that the second system behaves like the first system. Emulation focuses on exact
reproduction of external behavior, which is in contrast to simulation, which
concerns an abstract model of the system being simulated, often considering its
internal state.
Ethernet
Ethernet is a frame-based computer networking technology for local area
networks (LANs). It defines wiring and signaling for the physical layer, and frame
formats and protocols for the media access control (MAC)/data link layer of the
OSI model. Ethernet is mostly standardized as IEEE 802.3. It has become the most
widespread LAN technology in use during the 1990s to the present.
FTP
A File Transfer Protocol (FTP) is a commonly used protocol for exchanging files
over any network that supports the TCP/IP protocol (such as the Internet or an
intranet).
Fuser Unit
The part of a laser printer that fuses the toner onto the print media. It consists of
a heat roller and a pressure roller. After toner is transferred onto the paper, the
fuser unit applies heat and pressure to ensure that the toner stays on the paper
permanently, which is why paper is warm when it comes out of a laser printer.
Glossary
302
Glossary
Gateway
IEEE
A connection between computer networks, or between a computer network
and a telephone line. It is very popular, as it is a computer or a network that
allows access to another computer or network.
The Institute of Electrical and Electronics Engineers (IEEE) is an international
non-profit, professional organization for the advancement of technology
related to electricity.
Grayscale
IEEE 1284
A shades of gray that represent light and dark portions of an image when color
images are converted to grayscale; colors are represented by various shades of
gray.
The 1284 parallel port standard was developed by the Institute of Electrical and
Electronics Engineers (IEEE). The term "1284-B" refers to a specific connector
type on the end of the parallel cable that attaches to the peripheral (for example,
a printer).
Halftone
Intranet
An image type that simulates grayscale by varying the number of dots. Highly
colored areas consist of a large number of dots, while lighter areas consist of a
smaller number of dots.
Mass storage device (HDD)
Mass storage device (HDD), commonly referred to as a hard drive or hard disk, is
a non-volatile storage device which stores digitally-encoded data on rapidly
rotating platters with magnetic surfaces.
A private network that uses Internet Protocols, network connectivity, and
possibly the public telecommunication system to securely share part of an
organization's information or operations with its employees. Sometimes the
term refers only to the most visible service, the internal website.
IP address
An Internet Protocol (IP) address is a unique number that devices use in order to
identify and communicate with each other on a network utilizing the Internet
Protocol standard.
Glossary
303
Glossary
IPM
ITU-T
The Images Per Minute (IPM) is a way of measuring the speed of a printer. An IPM
rate indicates the number of single-sided sheets a printer can complete within
one minute.
The International Telecommunication Union is an international organization
established to standardize and regulate international radio and
telecommunications. Its main tasks include standardization, allocation of the
radio spectrum, and organizing interconnection arrangements between
different countries to allow international phone calls. A -T out of ITU-T indicates
telecommunication.
IPP
The Internet Printing Protocol (IPP) defines a standard protocol for printing as
well as managing print jobs, media size, resolution, and so forth. IPP can be used
locally or over the Internet to hundreds of printers, and also supports access
control, authentication, and encryption, making it a much more capable and
secure printing solution than older ones.
ITU-T No. 1 chart
Standardized test chart published by ITU-T for document facsimile
transmissions.
IPX/SPX
JBIG
IPX/SPX stands for Internet Packet Exchange/Sequenced Packet Exchange. It is a
networking protocol used by the Novell NetWare operating systems. IPX and
SPX both provide connection services similar to TCP/IP, with the IPX protocol
having similarities to IP, and SPX having similarities to TCP. IPX/SPX was
primarily designed for local area networks (LANs), and is a very efficient protocol
for this purpose (typically its performance exceeds that of TCP/IP on a LAN).
Joint Bi-level Image Experts Group (JBIG) is an image compression standard with
no loss of accuracy or quality, which was designed for compression of binary
images, particularly for faxes, but can also be used on other images.
ISO
JPEG
Joint Photographic Experts Group (JPEG) is a most commonly used standard
method of lossy compression for photographic images. It is the format used for
storing and transmitting photographs on the World Wide Web.
The International Organization for Standardization (ISO) is an international
standard-setting body composed of representatives from national standards
bodies. It produces world-wide industrial and commercial standards.
Glossary
304
Glossary
LDAP
MH
The Lightweight Directory Access Protocol (LDAP) is a networking protocol for
querying and modifying directory services running over TCP/IP.
Modified Huffman (MH) is a compression method for decreasing the amount of
data that needs to be transmitted between the fax machines to transfer the
image recommended by ITU-T T.4. MH is a codebook-based run-length
encoding scheme optimized to efficiently compress white space. As most faxes
consist mostly of white space, this minimizes the transmission time of most
faxes.
LED
A Light-Emitting Diode (LED) is a semiconductor device that indicates the status
of a machine.
MMR
MAC address
Media Access Control (MAC) address is a unique identifier associated with a
network adapter. MAC address is a unique 48-bit identifier usually written as 12
hexadecimal characters grouped in pairs (e. g., 00-00-0c-34-11-4e). This address
is usually hard-coded into a Network Interface Card (NIC) by its manufacturer,
and used as an aid for routers trying to locate machines on large networks.
Modified Modified READ (MMR) is a compression method recommended by ITUT T.6.
Modem
A device that modulates a carrier signal to encode digital information, and also
demodulates such a carrier signal to decode transmitted information.
MFP
MR
Multi Function Peripheral (MFP) is an office machine that includes the following
functionality in one physical body, so as to have a printer, a copier, a fax, a
scanner and etc.
Modified Read (MR) is a compression method recommended by ITU-T T.4. MR
encodes the first scanned line using MH. The next line is compared to the first,
the differences determined, and then the differences are encoded and
transmitted.
Glossary
305
Glossary
NetWare
OSI
A network operating system developed by Novell, Inc. It initially used
cooperative multitasking to run various services on a PC, and the network
protocols were based on the archetypal Xerox XNS stack. Today NetWare
supports TCP/IP as well as IPX/SPX.
Open Systems Interconnection (OSI) is a model developed by the International
Organization for Standardization (ISO) for communications. OSI offers a
standard, modular approach to network design that divides the required set of
complex functions into manageable, self-contained, functional layers. The layers
are, from top to bottom, Application, Presentation, Session, Transport, Network,
Data Link and Physical.
OPC
Organic Photo Conductor (OPC) is a mechanism that makes a virtual image for
print using a laser beam emitted from a laser printer, and it is usually green or
rust colored and has a cylinder shape.
An imaging unit containing a drum slowly wears the drum surface by its usage
in the printer, and it should be replaced appropriately since it gets worn from
contact with the cartridge development brush, cleaning mechanism, and paper.
Originals
The first example of something, such as a document, photograph or text, etc,
which is copied, reproduced or translated to produce others, but which is not
itself copied or derived from something else.
PABX
A private automatic branch exchange (PABX) is an automatic telephone
switching system within a private enterprise.
PCL
Printer Command Language (PCL) is a Page Description Language (PDL)
developed by HP as a printer protocol and has become an industry standard.
Originally developed for early inkjet printers, PCL has been released in varying
levels for thermal, dot matrix printer, and laser printers.
PDF
Portable Document Format (PDF) is a proprietary file format developed by
Adobe Systems for representing two dimensional documents in a device
independent and resolution independent format.
Glossary
306
Glossary
PostScript
Protocol
PostScript (PS) is a page description language and programming language used
primarily in the electronic and desktop publishing areas. - that is run in an
interpreter to generate an image.
A convention or standard that controls or enables the connection,
communication, and data transfer between two computing endpoints.
PS
Printer Driver
See PostScript.
A program used to send commands and transfer data from the computer to the
printer.
Print Media
The media like paper, envelopes, labels, and transparencies which can be used
in a printer, a scanner, a fax or, a copier.
PSTN
The Public-Switched Telephone Network (PSTN) is the network of the world's
public circuit-switched telephone networks which, on industrial premises, is
usually routed through the switchboard.
RADIUS
PPM
Pages Per Minute (PPM) is a method of measurement for determining how fast
a printer works, meaning the number of pages a printer can produce in one
minute.
Remote Authentication Dial In User Service (RADIUS) is a protocol for remote
user authentication and accounting. RADIUS enables centralized management
of authentication data such as usernames and passwords using an AAA
(authentication, authorization, and accounting) concept to manage network
access.
PRN file
Resolution
An interface for a device driver, this allows software to interact with the device
driver using standard input/output system calls, which simplifies many tasks.
The sharpness of an image, measured in Dots Per Inch (DPI). The higher the dpi,
the greater the resolution.
Glossary
307
Glossary
SMB
TCP/IP
Server Message Block (SMB) is a network protocol mainly applied to share files,
printers, serial ports, and miscellaneous communications between nodes on a
network. It also provides an authenticated Inter-process communication
mechanism.
The Transmission Control Protocol (TCP) and the Internet Protocol (IP); the set of
communications protocols that implement the protocol stack on which the
Internet and most commercial networks run.
TCR
SMTP
Simple Mail Transfer Protocol (SMTP) is the standard for e-mail transmissions
across the Internet. SMTP is a relatively simple, text-based protocol, where one
or more recipients of a message are specified, and then the message text is
transferred. It is a client-server protocol, where the client transmits an email
message to the server.
SSID
Service Set Identifier (SSID) is a name of a wireless local area network (WLAN). All
wireless devices in a WLAN use the same SSID in order to communicate with
each other. The SSIDs are case-sensitive and have a maximum length of 32
characters.
Transmission Confirmation Report (TCR) provides details of each transmission
such as job status, transmission result and number of pages sent. This report can
be set to print after each job or only after failed transmissions.
TIFF
Tagged Image File Format (TIFF) is a variable-resolution bitmapped image
format. TIFF describes image data that typically come from scanners. TIFF
images make use of tags, keywords defining the characteristics of the image that
is included in the file. This flexible and platform-independent format can be
used for pictures that have been made by various image processing
applications.
Toner Cartridge
Subnet Mask
The subnet mask is used in conjunction with the network address to determine
which part of the address is the network address and which part is the host
address.
A kind of bottle or container used in a machine like a printer which contains
toner. Toner is a powder used in laser printers and photocopiers, which forms
the text and images on the printed paper. Toner can be fused by by a
combination of heat/pressure from the fuser, causing it to bind to the fibers in
the paper.
Glossary
308
Glossary
TWAIN
Watermark
An industry standard for scanners and software. By using a TWAIN-compliant
scanner with a TWAIN-compliant program, a scan can be initiated from within
the program. It is an image capture API for Microsoft Windows and Apple Mac
operating systems.
A watermark is a recognizable image or pattern in paper that appears lighter
when viewed by transmitted light. Watermarks were first introduced in Bologna,
Italy in 1282; they have been used by papermakers to identify their product, and
also on postage stamps, currency, and other government documents to
discourage counterfeiting.
UNC Path
WEP
Uniform Naming Convention (UNC) is a standard way to access network shares
in Window NT and other Microsoft products. The format of a UNC path is:
\\<servername>\<sharename>\<Additional directory>
URL
Uniform Resource Locator (URL) is the global address of documents and
resources on the Internet. The first part of the address indicates what protocol to
use, the second part specifies the IP address or the domain name where the
resource is located.
Wired Equivalent Privacy (WEP) is a security protocol specified in IEEE 802.11 to
provide the same level of security as that of a wired LAN. WEP provides security
by encrypting data over radio so that it is protected as it is transmitted from one
end point to another.
WIA
Windows Imaging Architecture (WIA) is an imaging architecture that is originally
introduced in Windows Me and Windows XP. A scan can be initiated from within
these operating systems by using a WIA-compliant scanner.
USB
WPA
Universal Serial Bus (USB) is a standard that was developed by the USB
Implementers Forum, Inc., to connect computers and peripherals. Unlike the
parallel port, USB is designed to concurrently connect a single computer USB
port to multiple peripherals.
Wi-Fi Protected Access (WPA) is a class of systems to secure wireless (Wi-Fi)
computer networks, which was created to improve upon the security features of
WEP.
Glossary
309
Glossary
WPA-PSK
WPA-PSK (WPA Pre-Shared Key) is special mode of WPA for small business or
home users. A shared key, or password, is configured in the wireless access point
(WAP) and any wireless laptop or desktop devices. WPA-PSK generates a unique
key for each session between a wireless client and the associated WAP for more
advanced security.
WPS
The Wi-Fi Protected Setup (WPS) is a standard for establishing a wireless home
network. If your wireless access point supports WPS, you can configure the
wireless network connection easily without a computer.
XPS
XML Paper Specification (XPS) is a specification for a Page Description Language
(PDL) and a new document format, which has benefits for portable document
and electronic document, developed by Microsoft. It is an XML-based
specification, based on a new print path and a vector-based deviceindependent document format.
Glossary
310
Index
A
inside
78
entering character
outside
77
error message
pickup roller
80
scan unit
81
F
cleaning a machine
77
favorites settings, for printing
control panel
23
fax
13
accessing
management tools
290
address book
editing
group editing
199
200, 199
registering
198
convention
using
198
copy
address book setup
AnyWeb Print
general setup
198
238
copying
authorized users
registering
202
B
buttons
eco
23, 25
id copy
23, 24
numeric keypad
25
print screen
24
scan to
wps
23
24, 26
basic copying
56
reducing or enlarging copies
58
cleaning
98
53
adding documents to a reserved fax
225
227,
canceling a reserved fax job
227, 230
delaying a fax transmission
226
forwarding a received fax to another
destination
229, 228
general setup
182
D
Printing sent fax report automatically 233
default settings
receiving a fax in the computer 230, 233,
231,
232, 231, 233, 231, 232, 225
tray setting
direct printing utility
45
211
sending a fax in the computer
fax feature
226, 228
225
fax sending
E
multi sending
easy document creator
243
e-book conversion
243
eco printing
C
180
197
email address
searching
54
195
196, 195
63
faxing
adjusting darkness
65, 64
preparing to fax
62
receiving in Fax mode
64
features
5
Index 311
Index
machine features
178
common Linux problems
print media feature
106
driver installation for network connected
144,
133, 134
front view
20
printer properties
G
general icons
13
general settings
185
glossary
299
I
59
installation
accessories
291
223
linux scanning
223
jam
clearing original document
tips for avoiding paper jams
86, 91
85
234, 235
menu overview
31
multi-purpose tray
tips on using
41
using special media
41
39
N
special media
41
network
47
M
Mac
270
driver installation
Linux
Mac
Windows
144
143
140
general setup
191
driver installation for network connected
143,
131, 132
installing environment
printing
SetIP program
scanning
222, 110
L
mac scanning
222
LCD display
machine information
manual feeding
145
137, 138, 166
wired network setup
137, 148
n-up printing
Mac
213
180, 181, 182, 189
O
machine setup
machine status
112, 136
IPv6 configuration
212
138
Linux
41
memory/hard drive feature
paper in the tray1
using SetIP
browsing the machine status 180, 181, 182,
189
loading
loading
common Mac problems
J
215, 214
scanning
loading originals
id copy
271
180, 181, 182, 189
optional memory
setting up the optional memory
235
Index 312
Index
output support
45
general information
247
printing
overlay printing
create
209
changing the default print settings
203
delete
209
Linux
214
print
209
Mac
212
multiple pages on one sheet of paper
Mac
213
P
placing a machine
adjusting the altitude
194
postScript driver
troubleshooting
preparing originals type
46
setting as a default machine
using direct printing utility
173
print media
214
Mac
212
envelope
42
printing feature
labels
43
problem
preprinted paper
setting the paper size
44
45, 41
printer preferences
Linux
printer status
215
211
Linux
44
106
203, 205
printing a document
card stock
output support
50
213
204
272
print
mobile OS
printing a document
Windows
Mac
operating system problems
203
269
problems
copying problems
264
faxing problems
267
paper feeding problems 250, 251, 252, 256
scanning problems
265
R
rear view
regulatiory information
22
113
reports
machine information 180, 182, 183, 184,
185,
186, 189, 190
resolution
faxing
64
S
safety
information
14
symbols
14
Samsung Easy Document Creator
221
samsung printer experience
283
Samsung Printer Status
247
scan feature
216
Scanning
Scanning with Samsung Easy Document
Creator
221
scanning
basic information
216
Linux scanning
223
Mac scanning
222
Index 313
Index
Scanning from image editing program 220,
217,
218, 219, 221
service contact numbers
SetIP program
293
redistributing toner
storing
71, 73
69
system requirements
tray
137, 166
driver installation for network connected
140,
28, 29, 278, 276, 280
adjusting the width and length
38
using SetIP
109
137, 166
Windows 8
Special features
193
changing the tray size
38
specifications
104
manual feeding
41
driver uninstallation
282
print media
106
setting the paper size and type
45
network
driver installation
278
USB cable
driver installation
276
wireless
driver installation
280
status
Storing
23, 25
195
supplies
troubleshooting
U
available supplies
68
understanding the status LED
estimated toner cartridge life
70
Unix
monitoring the supplies life
75
ordering
68
replacing toner cartridge
73
system requirements
general information
240
SyncThru™ Web Service
240
95
111
driver installation 28, 29, 131, 133, 132, 134
53, 214
W
T
create
208
toner cartridge
delete
208
208
70
edit
handling instructions
69
Windows
non-Samsung and refilled
69, 73
common Windows problems
USB cable
WPS
disconnectiong
PBC
148
155, 158
152
153
wireless network
watermark
estimated life
wireless
Infrastructure mode
USB cable
using help
SyncThru Web Service
292
network cable
165
269
Index 314