Samsung HW-C500 User Manual

HW-C500
HW-C560S
AV Receiver System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
HW-C500-C560S-EUR-0615.indd 1
2010-06-16
3:07:10
Safety information
SAFETY WARNINGS
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.
WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
• This apparatus shall always be connected to a AC outlet with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the
mains plug shall be readily operable.
CAUTION
• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
• The Mains plug is used as a disconnect device and shall stay readily operable at any time.
Wiring the Main Power Supply Plug (UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on
the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the
same colour as the fuse fitted in the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you
should obtain a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect
the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord.
Never attempt to insert bare wires directly into a mains socket. A plug and fuse must be used at all times.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER E OR BY THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
2
HW-C500-C560S-EUR-0615.indd 2
2010-06-16
3:07:24
ENG
PRECAUTIONS
7 cm
SETUP
10 cm
INPUT SELECT
TONE CONTROL
ENTER
SOUND EFFECT
ASC MIC
ASC
10 cm
AUDIO
ASSIGN
MULTI CH
INPUT
S. DIRECT
AV
SYNC
TUNING
MODE
SELECT
MEMORY
10 cm
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your
player horizontally, on a suitable base (furniture), with enough space around it for ventilation (7.5~10cm). Make sure
the
ventilation slots are not covered. Do not stack anything on top of the amplifier. In order to disconnect the player completely from the
power supply, remove the AC plug from the wall outlet, especially when left unused for a long period of time.
SETUP
INPUT SELECT
ENTER
TONE CONTROL
SETUP
SOUND EFFECT
INPUT SELECT
ASC MIC
ASC
AUDIO
ASSIGN
S. DIRECT
MULTI CH
INPUT
AV
SYNC
TUNING
MODE
SELECT
ENTER
TONE CONTROL
SOUND EFFECT
MEMORY
ASC MIC
During thunderstorms, disconnect the AC plug from the
wall outlet.
Voltage peaks due to lightning could damage the unit.
ASC
AUDIO
ASSIGN
S. DIRECT
MULTI CH
INPUT
AV
SYNC
TUNING
MODE
SELECT
MEMORY
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of
the unit.
SETUP
INPUT SELECT
ENTER
TONE CONTROL
SOUND EFFECT
ASC MIC
ASC
AUDIO
ASSIGN
S. DIRECT
MULTI CH
INPUT
AV
SYNC
TUNING
MODE
SELECT
MEMORY
Phones
Protect the player from moisture(i.e.vases), and excess
heat(e.g.fireplace) or equipment creating strong magnetic or
electric fields (i.e.speakers...). Disconnect the power cable
from the AC supply if the player malfunctions. Your player is
not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc have been
stored in cold temperatures.
If transporting the player during the winter, wait
approximately 2 hours until the unit has reached room
temperature before using.
The batteries used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
3
HW-C500-C560S-EUR-0615.indd 3
2010-06-16
3:07:25
Features
Digital AV Receiver
iPod
This product is a pure digital AV receiver that performs
digital signal processing to minimize signal distortion and
loss.
You can enjoy music files by connecting your iPod/iPhone
to the AV Receiver with the supplied iPod dock.
Dolby Pro Logic II
DPL II processes any high quality stereo signal source
into five separate full frequency channels.
SFE (Sound Field Effect) Using
32bit Audio Digital Signal
Processing
DTS 96/24
Provides more realistic surround sound with normal
stereo audio sources.
DTS 96/24 encodes standard 16 bit/44.1 kHz sound to
Anynet+ (HDMI-CEC) Function
24 bit/96kHz and applies it to a 5.1 CH sound track.
DTS (Digital Theater Systems)
DTS provides a discrete 5.1 CH digital audio signal for
both music and movie contents and uses less
compression than Dolby Digital for richer sound.
Anynet+ is a function that can be used to operate this
AV Receiver with a Samsung TV remote control, by
connecting the receiver to a SAMSUNG TV using an
HDMI Cable. (This function is available only in
connection with Samsung TV and DVD player
supporting Anynet+(HDMI-CEC).)
ACCESSORIES
INPUT SELECT
TV SOURCE
POWER
AMP/TV
DIMMER
BD/DVD
RDS DISPLAY
TA
1
2
3
PTY-
PTY SEARCH
PTY+
4
5
6
SLEEP
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
MUTE
TUNING
/CH
VOL
ASC
TUNER MEMORY
SUBWOOFER
SETUP/MENU
BD/DVD
MULTI CH
MO/ST
INFO
RETURN
EXIT
SAT
TV
AUX
CD
iPod
Remote Control/
Batteries (AAA size)
FM antenna
User’s manual
iPod Dock
ASC microphone
4
HW-C500-C560S-EUR-0615.indd 4
2010-06-16
3:07:30
ENG
Contents
SAFETY INFORMATION
2
Safety Warnings
Precautions
4
Accessories
7
8
10
11
11
12
Front Panel
Rear Panel
Display
Insert Remote Control Batteries
Operation Range of the Remote Control
Tour of the Remote Control
14
16
18
19
20
21
22
23
24
25
26
Speaker Positioning
Connecting the Speakers
Connecting External Devices/Your TV via
HDMI
HDMI Function
Connecting to Your TV
Connecting a DVD or BD(Blu-ray) Player
Connecting a Cable, Satellite or Set-top Box
Connecting a CD Player
Connecting 5.1 Channel Devices
Connecting an iPod
Connecting the FM Antenna
27
27
28
Before Using the AV Receiver
Audio Setup
Selecting Digital/Analogue Input
● CONTENTS
FEATURES
2
3
4
DESCRIPTION
7
CONNECTIONS
14
BASIC FUNCTIONS OF YOUR AV
RECEIVER
27
5
HW-C500-C560S-EUR-0615.indd 5
2010-06-16
3:07:30
Contents
SETUP
29
OPERATION
42
MISCELLANEOUS
51
TROUBLESHOOTING
29
33
34
35
36
37
37
38
39
39
39
40
41
41
41
Setup Menu Tree
Setting the Speaker Size
Setting the Speaker Listening Distance
Setting the Speaker Level
Setting the Test Tone
Setting Dolby Pro Logic II Mode
Setting Dolby Pro Logic II
Setting Tone Control
AV SYNC
MP3 Enhancer
Smart Volume
ASC (Auto Sound Calibration) Setup
DRC Setup
HDMI Setup
Variable Set
42
43
44
45
47
49
50
Using the Surround Modes
Using the Subwoofer Selection Button
Listening to the Radio
About RDS Broadcasting
Using an iPod
Convenient Functions
Software Upgrade
51
53
Operating Your TV With the Remote Control
Operating your DVD or BD player with the
remote control
54
Troubleshooting
56
Specifications
54
APPENDIX
56
6
HW-C500-C560S-EUR-0615.indd 6
2010-06-16
3:07:30
ENG
Description
FRONT PANEL
1
2
3 4
5
6
7
8
● DESCRIPTION
SETUP
INPUT SELECT
ENTER
TONE CONTROL
SOUND EFFECT
ASC MIC
9
ASC
AUDIO
ASSIGN
S. DIRECT
/STEREO
MULTI CH
INPUT
AV
SYNC
TUNING
MODE
10 11 12 13 14 15
SELECT
16
MEMORY
17
Used to select a source. (FM BD/DVD SAT TV CD AUX 5.1 MULTI CH IPOD AUDIO IPOD VIDEO).
1
INPUT SELECT
2
UP(,), DOWN(.), LEFT(<),
RIGHT(>), ENTER
Used to move the cursor up, down, left or right and select an item in the SETUP menu.
3
SETUP
Displays the SETUP menu.
4
TONE CONTROL
Used to set the bass, treble level and tone to on/off.
5
SOUND EFFECT
Toggles to select a surround sound mode.
6
DISPLAY
Displays the speaker/audio input status, listening mode, etc
7
VOLUME CONTROL
Adjusts the volume level.
8
POWER
Turns the receiver on/off.
9
ASC MIC JACK
Used to connect the ASC MIC for setting up ASC (Auto Sound Calibration).
10
ASC BUTTON
Used to select the ASC(Auto Sound Calibration) mode.
11
AUDIO ASSIGN BUTTON
Toggles to select an input mode for the selected source.
12
S.DIRECT/STEREO BUTTON
Used to select the S.DIRECT or STEREO mode.
13
MULTI CH INPUT BUTTON
Used to select a connected 5.1 multi channel player.
14
AV SYNC BUTTON
Used to select the Audio Delay Mode.
15
TUNING MODE BUTTON
Used to select the Manual or Preset mode for FM radio.
16
SELECT BUTTON
Used to change the radio frequency.
17
MEMORY BUTTON
Used to set a preset radio frequency.
Also used to select detailed options in the SOUND EFFECT mode and to change the tone level.
7
HW-C500-C560S-EUR-0615.indd 7
2010-06-16
3:07:30
Description
REAR PANEL
< HW-C500 >
1
2
3
4
5
6 7
iPod
8 9 10 11 12
13
14
15
< HW-C560S >
1
2
3
4
5
6 7
iPod
8 9 10 11 12
13
14
15
* All those pictures of the Rear panel are based on Model HW-C560S.
8
HW-C500-C560S-EUR-0615.indd 8
2010-06-16
3:07:31
ENG
FM ANTENNA JACK
Connect the FM Antenna here.
2
MULTI CH IN JACKS
Receives the analogue audio signal from an external player with a multi-channel port.
3
VIDEO IN JACKS
Receives the video signal from a video player (BD/DVD, SAT, TV).
4
HDMI IN JACKS
Receives digital video and audio signals simultaneously using an HDMI cable.
5
HDMI OUT JACK
Outputs digital video and audio signals simultaneously using an HDMI cable.
6
USB PORT
Can be only used for firmware upgrades.
7
VIDEO OUT JACK
Outputs the video signal to video devices (TV, Projector etc).
8
COMPONENT VIDEO IN JACKS
Receives the component video signal.
9
COMPONENT VIDEO OUT JACKS
Outputs the component video signal.
10
iPod JACK
Receives the audio/video signal from an iPod.
11
OPTICAL IN JACKS (DIGITAL AUDIO IN)
Receives the digital optical audio signal.
12
COAXIAL IN JACK (DIGITAL AUDIO IN)
Receives the digital coaxial audio signal.
13
AUDIO IN JACKS
Receives the audio signal from a video player (BD/DVD, SAT, TV, CD).
14
SUBWOOFER AUDIO OUT JACK
Connect the subwoofer.
15
SPEAKER OUT TERMINALS
Speaker connection terminals.
● DESCRIPTION
1
9
HW-C500-C560S-EUR-0615.indd 9
2010-06-16
3:07:33
Description
DISPLAY
1
2
3
4
5
7
6
1
SPEAKER INDICATORS
Displays the connected speakers.
2
LISTENING MODE INDICATORS
Displays the current listening mode.
3
TUNING INDICATORS
Displays the status of the current radio broadcast.
4
AUDIO INPUT INDICATORS
Displays the audio input signal type of the currently connected external audio source.
5
SPEAKER LEVEL INDICATOR
Displays the speaker level.
6
RADIO FREQUENCY INDICATORS Displays the current radio frequency range.
7
MESSAGE DISPLAY
Informs you of the status of the receiver.
10
HW-C500-C560S-EUR-0615.indd 10
2010-06-16
3:07:33
ENG
INSERT REMOTE CONTROL BATTERIES
* Batteries (AAA size)
● DESCRIPTION
M
Follow these precautions to avoid leaking or cracking cells:





Place batteries in the remote control so they match the polarity : (+) to (+) and (–) to (–).
Assuming typical TV usage, the batteries last for about one year.
Use the correct type of batteries. Batteries that look similar may differ in voltage.
Always replace both batteries at the same time.
Do not expose the batteries to heat or a flame.
OPERATION RANGE OF THE REMOTE CONTROL
The remote control can be used up to approximately 7 meters in a straight line. It can also be operated at a
horizontal angle of up to 30° from the remote control sensor.
SETUP
INPUT SELECT
ENTER
TONE CONTROL
SOUND EFFECT
ASC MIC
ASC
AUDIO
ASSIGN
S. DIRECT
/STEREO
MULTI CH
INPUT
AV
SYNC
TUNING
MODE
SELECT
MEMORY
INPUT SELECT
TV SOURCE
POWER
AMP/TV
DIMMER
BD/DVD
RDS DISPLAY
TA
1
2
3
PTY-
PTY SEARCH
PTY+
4
5
6
SLEEP
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
MUTE
TUNING
/CH
VOL
ASC
TUNER MEMORY
SUBWOOFER
SETUP/MENU
INFO
RETURN
BD/DVD
MULTI CH
MO/ST
EXIT
SAT
TV
AUX
CD
iPod
11
HW-C500-C560S-EUR-0615.indd 11
2010-06-16
3:07:34
Description
TOUR OF THE REMOTE CONTROL
INPUT SELECT
TV SOURCE
POWER
1
2
AMP/TV
DIMMER
BD/DVD
RDS DISPLAY
3
TA
1
2
3
PTY-
PTY SEARCH
PTY+
5
6
4
SLEEP
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
4
22
6
23
7
9
10
11
MUTE
TUNING
/CH
VOL
ASC
TUNER MEMORY
SUBWOOFER
MO/ST
SETUP/MENU
INFO
RETURN
EXIT
12
13
14
20
21
5
8
15
16
17
18
19
BD/DVD
MULTI CH
SAT
TV
AUX
24
25
26
27
28
29
CD
iPod
12
HW-C500-C560S-EUR-0615.indd 12
2010-06-16
3:07:34
ENG
POWER BUTTON
Turns the receiver on/off.
2
AMP/TV BUTTON
Used to select the AMP/TV mode.
- If you select the AMP mode, the button will flash orange.
- If you select the TV mode, the button will flash green.
3
NUMBER BUTTONS
Used to select a TV channel.
4
PROLOGIC BUTTON
Select the desired Dolby Pro Logic II audio mode.
5
SKIP BUTTONS
Press to skip backwards or forwards on a connected DVD/BD player or iPod.
6
STOP/PLAY BUTTON
Press to stop/start playback on a connected DVD/BD player or iPod.
7
MUTE BUTTON
Mutes the sound of a connected device.
8
VOLUME CONTROL BUTTONS
Adjusts the volume of the selected device.
9
SUBWOOFER BUTTON
Used to select the Subwoofer.
10
TUNER MEMORY BUTTON
Used to set a preset radio frequency.
11
SETUP/MENU BUTTON
Displays the SETUP menu.
12
UP/DOWN/LEFT/RIGHT
BUTTONS
Used to navigate the menus.
13
RETURN BUTTON
Used to return to the previous menu from the SETUP menu.
14
FUNCTION SELECTOR
BUTTONS
Used to select an input source.
15
INPUT SELECT,
TV SOURCE BUTTON
Toggles to find and select an input source.
Press to select a connected TV's video source.
16
DIMMER BUTTON
Adjusts the brightness of the display.
17
BD/DVD BUTTON
Used to select the BD/DVD mode.
- If you select the BD mode, the button will flash orange.
- If you select the DVD mode, the button will flash green.
18
RDS SELECTION BUTTONS
Used to select the RDS functions.
19
SLEEP BUTTON
Used to set the Sleep Timer.
20
AUDIO ASSIGN BUTTON
Toggles to select an input mode for the selected source.
21
DSP BUTTON
Used to select the SFE mode.
22
SEARCH BUTTONS
Press to search backwards or forwards.
23
PAUSE BUTTON
Pauses playback on a connected device.
24
TUNING/CHANNEL BUTTONS
Used to change the radio broadcasting frequency or TV channel.
25
ASC BUTTON
Used to set the Auto Sound Calibration function.
26
MO/ST BUTTON
Select MONO or STEREO for radio broadcasts.
27
INFO BUTTON
Display information on the connected device currently being used.
28
ENTER BUTTON
Used to select an item in the SETUP menu.
29
EXIT BUTTON
Exits the SETUP menu.
● DESCRIPTION
1
13
HW-C500-C560S-EUR-0615.indd 13
2010-06-16
3:07:35
Connections
This section involves various methods of connecting the AV receiver to other
external components.
Before moving or installing the product, be sure to turn off the power and
disconnect the power cord.
SPEAKER POSITIONING
* The HW-C500 model does not supply speakers (sold separately).
2~3m
AV
RECEIVER
SETUP
INPUT SELECT
ENTER
TONE CONTROL
SOUND EFFECT
ASC MIC
ASC
AUDIO
ASSIGN
S. DIRECT
/STEREO
MULTI CH
INPUT
AV
SYNC
TUNING
MODE
SELECT
MEMORY
SL
SR
Position of AV Receiver
Place the AV Receiver on a dedicated stand or rack.
Subwoofer
The position of the subwoofer is not so critical. Place it anywhere you like.
Front Speakers
Place these speakers in front of your listening position, facing inwards (about 45°) toward you.
Place the speakers so that their tweeters will be at the same height as your ears.
Align the front face of the front speakers with the front face of the centre speaker or place them slightly
in front of the centre speaker.
14
HW-C500-C560S-EUR-0615.indd 14
2010-06-16
3:07:35
ENG
Centre speaker
It is best to install it at the same height as the front speakers.
You can also install it directly over or under the TV.
● CONNECTIONS
Surround Speakers
Place these speakers behind your listening position.
If there isn't enough room, place these speakers so they face each other.
Place them about 60 to 90cm above your ears, facing slightly downward.
Unlike the front and centre speakers, the surround speakers are used to handle mainly sound effects
and sound will not come from them all the time.
M
When you attach the speakers to the wall, make sure to fasten them tightly so they do not fall off.
Speaker Configuration
For the best surround-sound experience, you should connect five speakers and a powered subwoofer.
The following table shows which channels you should use based on the number of speakers you have.
2 speakers
M
3 speakers
4 speakers
5 speakers
If you place a speaker near your TV set, screen colour may be distorted because of the magnetic field
generated by the speaker. If this occurs, place the speaker away from your TV set.
15
HW-C500-C560S-EUR-0615.indd 15
2010-06-16
3:07:36
Connections
CONNECTING THE SPEAKERS (HW-C500)
FRONT (R) SURROUND (R)
(not supplied) (not supplied)
SUBWOOFER
(not supplied)
ACTIVE SUBWOOFER
(not supplied)
SURROUND (L) FRONT (L)
(not supplied) (not supplied)
SW
CENTRE
(not supplied)
iPod
Model HW-C500
AV Receiver
M
HW-C500
 The HW-C500 model does not supply speakers (sold separately). Contact a Samsung Electronics retailer for
purchasing.
Connecting Speaker Wire
1. Loosen the knob by turning counterclockwise.
2. Insert the bare part of the wire into the hole in the side of each
terminal.
3. Tighten the knob by turning clockwise to secure the wire.
M
Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or objects into
the duct (hole).
 Never touch speaker terminals while the power is on. Doing so could result in electric shock.
 Make sure the polarities (+ and -) are correct.
Connecting the Speakers
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into the
red (+) terminal, and then release the tab.
3. Connect the connecting plugs to the back of the AV Receiver.
• Make sure the colors of the speaker terminals on the back of the
AV receiver match the colors of the connecting plugs.
Black
Red
16
HW-C500-C560S-EUR-0615.indd 16
2010-06-16
3:07:37
ENG
CONNECTING THE SPEAKERS (HW-C560S)
FRONT (R) SURROUND (R) SUBWOOFER
PS-FC560S PS-RC560S
PS-WC560S
● CONNECTIONS
ACTIVE SUBWOOFER
(not supplied)
SURROUND (L) FRONT (L)
PS-RC560S PS-FC560S
SW
CENTRE
PS-CC560S
iPod
M
Model HW-C560S
AV Receiver
HW-C560S
FRONT SPEAKER
PS-FC560S
CENTRE SPEAKER
PS-CC560S
SURROUND SPEAKER
PS-RC560S
SUBWOOFER
PS-WC560S
 The Active Subwoofer is sold separately. Contact a Samsung Electronics retailer for purchasing.
Connecting the Speakers
1
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into
the red (+) terminal, and then release the tab.
3. Press down the terminal tab on the back of the AV Receiver.
2
Red
Black
4. Insert the one wire into the terminal + and the other one into the
terminal -.
• Make sure the colours of the speaker terminals on the back of the
AV receiver match the colours of the connecting plugs.
Speaker
3
M
Keep the subwoofer speaker out of reach of children to prevent them
from inserting their hands or objects into the duct (hole).
 Never touch speaker terminals while the power is on. Doing so could
result in electric shock.
 Make sure the polarities (+ and -) are correct.
4
AV Receiver
HW-C500-C560S-EUR-0615.indd 17
17
2010-06-16
3:07:39
Connections
CONNECTING EXTERNAL DEVICES/YOUR TV VIA HDMI
HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray player, set-top
box and more.
HDMI removes any loss of signal from analogue conversion, enabling you to enjoy video and audio sound quality as it
was originally created in the digital source.
By connecting through the HDMI(High-Definition Multimedia Interface) interface, you can play back digital video and audio.
DVD or
Blu-ray Player
SAT
(Cable/Satellite/Set-top box)
Game console
or
HDTV Tuner
Camcorder
(HDTV Terrestrial Receiver)
ONLY USE FOR
FIRMWARE UPDATE
iPod
• Connect it if you want
to use Anynet+.
OPTICAL
OUT
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both the connected external device and TV must
support High-bandwidth Digital Content Protection System (HDCP). This product supports HDCP.
Compatibility with a TV Supporting HDMI
A TV with an HDMI jack.
Video/Audio
A TV with a DVI-D jack (TV supporting HDCP)
Video
A TV with a DVI-D jack (TV not supporting HDCP)
-
M
Audio from SACD discs will not be heard with this connection. To play a DVD disc whose copyright is protected
by CPPM, use a player supporting CPPM.
 The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the
performance of the connected device.
 Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.
18
HW-C500-C560S-EUR-0615.indd 18
2010-06-16
3:07:43
ENG
HDMI FUNCTION
Using Anynet+(HDMI-CEC)
● CONNECTIONS
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's
remote control. Anynet + can be used by connecting this AV Receiver to a SAMSUNG TV using an
HDMI Cable. This is only available with SAMSUNG TVs and SAMSUNG AV Products that support
Anynet+.
1. Connect the AV receiver to a Samsung TV with an HDMI cable. (See page 18)
2. Set the Anynet+ function on your TV.
(See the TV instructions manual for more information.)
• You can operate the volume on the AV receiver by using the Volume buttons on the TV remote
control.
To turn on Anynet+
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select HDMI SETUP, and then press the ENTER or ► button.
4. Press the ▲▼ buttons to select HDMI ANYNET+, and then press the ENTER or ► button.
5. Press the ▲▼ buttons to set ANYNET+ to ON.
- To exit setup mode• Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
M
If you use an HDMI cable to connect a Samsung TV to your AV Receiver, you can operate the AV receiver using
the TV’s remote control. This function is available only in connection with Samsung TV and DVD player
supporting Anynet +(HDMI-CEC).
 Please check your TV for the n logo. If your TV has an n logo, then it supports the Anynet+
function.
 When you are making Anynet+ connection, do not connect more than two AV receivers (Anynet+ installed).
Otherwise, it can cause a malfunction.
19
HW-C500-C560S-EUR-0615.indd 19
2010-06-16
3:07:45
Connections
CONNECTING TO YOUR TV
iPod
or
COMPONENT VIDEO
IN
IN
or
OPTICAL
OUT
AUDIO
OUT
Video Connection
If your television is equipped with Component Video inputs, connect a Component video cable(not
supplied) from the Component Video Output (PR, PB and Y) jacks on the back of your AV Receiver to the
Component Video Input jacks on your TV.
OR
Connect the Video cable from the VIDEO OUT (MONITOR) jack on the back of your AV Receiver to the
Video Input jack on your TV.
Audio Connection
Connect the Digital Input (OPTICAL 3) on your AV Receiver to the Digital Output of the TV.
OR
Connect AUDIO IN (TV) on your AV Receiver to the Audio Out of the TV.
20
HW-C500-C560S-EUR-0615.indd 20
2010-06-16
3:07:45
ENG
CONNECTING A DVD OR BD(Blu-ray) PLAYER
VIDEO
IN
● CONNECTIONS
COMPONENT
IN
or
iPod
or
DVD or BD Player
COMPONENT OPTICAL
OUT
OUT
AUDIO
OUT
VIDEO
OUT
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (BD/DVD) (PR, PB and Y)
jacks on the back of your AV Receiver to the Component Video Output jacks on your DVD/BD player.
OR
Connect a Video cable from the VIDEO IN (BD/DVD) jack on the back of your AV Receiver to the Video
Output jack on your DVD/BD player.
Audio Connection
Connect the Digital Input (OPTICAL 1) on your AV Receiver to the Digital Output of the DVD/BD player.
OR
Connect AUDIO IN (BD/DVD) on your AV Receiver to the Audio Out of the DVD/BD player.
21
HW-C500-C560S-EUR-0615.indd 21
2010-06-16
3:07:47
Connections
CONNECTING A CABLE, SATELLITE OR SET-TOP BOX
COMPONENT
IN
VIDEO
IN
or
iPod
or
COMPONENT OPTICAL
OUT
OUT
AUDIO
OUT
VIDEO
OUT
SAT(Cable/Satellite/Set-top box)
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (SAT) (PR, PB and Y) jacks
on the back of your AV Receiver to the Component Video Output jacks on your SAT.
OR
Connect a Video cable from the VIDEO IN (SAT) jack on the back of your AV Receiver to the Video
Output jack on your SAT.
Audio Connection
Connect the Digital Input (OPTICAL 2) on your AV Receiver to the Digital Output of the SAT.
OR
Connect AUDIO IN (SAT) on your AV Receiver to the Audio Out of the SAT.
M
Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
 If the cable/set-top box has only one audio output jack, connect it to either the right or left audio input jack of
the main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
22
HW-C500-C560S-EUR-0615.indd 22
2010-06-16
3:07:49
ENG
CONNECTING A CD PLAYER
● CONNECTIONS
CD player
AUDIO
OUT
COAXIAL
OUT
or
iPod
Audio Connection
Connect the Digital Input (COAXIAL) on your AV Receiver to the Digital Output of the CD Player.
OR
Connect AUDIO IN (CD) on your AV Receiver to the Audio Out of the CD player.
M
If the CD player has only one audio output jack, connect it to either the right or left audio input jack of the main
unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
23
HW-C500-C560S-EUR-0615.indd 23
2010-06-16
3:07:52
Connections
CONNECTING 5.1 CHANNEL DEVICES
You can connect the AV receiver to a DVD player, SUPER AUDIO CD player or other device with 5.1 channel output.
C
SW
iP
iPod
SW
FRONT
SURROUND
C
CENTER
SUB
WOOFER
5.1 CH
5.1 Channel device
24
HW-C500-C560S-EUR-0615.indd 24
2010-06-16
3:07:54
ENG
CONNECTING AN iPod
You can listen to audio from an iPod through the main unit. For iPod operation with your receiver, see this page and
47 ~ 48.
● CONNECTIONS
iPod
iPod
1. Connect the iPod dock connector to the iPod jack on your reciever.
2. Place the iPod in the Dock.
• If you want to play a movie stored in your iPod player, you should set the player's TV Out option to
On before inserting it into the dock. See page 48.
3. Press the iPod button on the remote control.
• You can also use the INPUT SELECT button on the main unit.
The mode switches as follows :
FM BD/DVD SAT TV CD AUX 5.1 MULTI CH IPOD AUDIO IPOD VIDEO
Disconnecting an iPod
Follow the steps below to prevent damage to an iPod and data when disconnecting from your
AV receiver.
1. Press the INPUT SELECT button on the main unit to switch to a mode other than IPOD AUDIO or
IPOD VIDEO.
OR
1. Turn off the AV Receiver.
2. Disconnect the iPod player from the iPod dock, or remove the iPod dock connector from the AV
receiver.
M





You must have the VIDEO (Monitor) output connected to your TV to view iPod video. See page
21.
Adjust the volume to a moderate level before you connect your iPod and AV Receiver.
When the unit is powered on and you connect an iPod, the unit will charge your iPod's battery.
Make sure to connect the dock connector so that the label “SAMSUNG” faces upward.
“Made for iPod” means that an electronic accessory has been designed to connect specifically to an iPod and
has been certified by the developer to meet Apple performance standards.
“Works with iPhone” means that an electronic accessory has been designed to connect specifically to an
iPhone and has been certified by the developer to meet Apple performance standards.
25
HW-C500-C560S-EUR-0615.indd 25
2010-06-16
3:07:56
Connections
CONNECTING AN iPod (Continued)
iPod models that are compatible with HW-C500/HW-C560S
M
"Made for iPod" means that the dock has been designed to connect specifically for the iPod and has been certified by the
developer to meet Apple performance standards.
 Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
iPhone is a trademark of Apple Inc.
CONNECTING THE FM ANTENNA
1. Connect the FM antenna supplied to the FM ANTENNA terminal as a temporary measure.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or
other rigid surface.
FM antenna (supplied)
iPod
M
 Do not place the antenna cable close to the power cord. Keep it as far away as possible.
 If you experience poor FM reception, use an external antenna.
26
HW-C500-C560S-EUR-0615.indd 26
2010-06-16
3:07:58
ENG
Basic functions of your AV Receiver
BEFORE USING THE AV RECEIVER
Turning On/Off
Connect the power plug to the outlet.
Remote control functions
You can operate your AMP (this AV receiver)/ TV and BD(Samsung only)/ DVD player with this remote control.
See pages 51 ~ 53 for more details.
To select a function
Method 1
Press the INPUT SELECT button.
• Each time you press this button, FM BD/DVD SAT TV CD AUX 5.1 MULTI CH IPOD AUDIO IPOD VIDEO will be selected in turn.
● BASIC FUNCTIONS OF YOUR AV RECEIVER
Press the POWER button on the main unit for 2 seconds.
• This unit will be turned on or set to Standby mode.
• You can also turn the unit on/off by pressing the POWER button on the remote control.
Method 2
Press the TUNING/CH, BD/DVD, SAT, TV, CD, MULTI CH, AUX or IPOD button.
• You can directly select the desired function.
AUDIO SETUP
Selecting a source device and connection jack
Select the external devices you have connected to the receiver.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches
between SETUP ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select AUDIO SETUP, and then press
the ENTER or ► button.
Æ
4. Press the ▲▼ buttons to select a desired jack.
• The source device switches as follows; BD/DVD, SAT, TV,
CD
- To exit setup mode • Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
M
You can also use SETUP, ,,.,<,>, ENTER on the front of your AV Receiver.
27
HW-C500-C560S-EUR-0615.indd 27
2010-06-16
3:08:00
Basic functions of your AV Receiver
SELECTING DIGITAL/ANALOGUE INPUT
You can listen to sound in 2 channel analogue , Dolby Digital or DTS using this unit.
1. Press the INPUT SELECT button to select a desired function (BD/DVD, SAT,TV,
CD). See page 27.
2. Press the AUDIO ASSIGN button on the remote control to select the external
device you have connected.
• Each time you press this button, the input mode changes as follows:
INPUT SELECT
TV SOURCE
POWER
AMP/TV
DIMMER
BD/DVD
1
2
3
PTY-
PTY SEARCH
PTY+
4
5
6
RDS DISPLAY
TA
• For BD/DVD function
Ä
Ä
Ä
Ä
Ä
Ä
• For SAT function
• For TV function
• For CD function
Ä
M
 You can also change the input mode by pressing the AUDIO ASSIGN button on the front of your AV Receiver.
 You can enjoy Dolby Digital or DTS if you connect the digital audio output jack of an external audio component to the optical
or coaxial digital audio input jack on the main unit.
28
HW-C500-C560S-EUR-0615.indd 28
2010-06-16
3:08:00
ENG
Setup
For your convenience, you can set this AV receiver's features for the best use.
SETUP MENU TREE
Here’s a quick look at how the setup menus are organized on your AV Receiver.
● SETUP
AUDIO SETUP
BD/DVD
OPT 1,2,3
COAX
OPT 1,2,3
COAX
OPT 1,2,3
COAX
OPT 1,2,3
COAX
SAT
TV
CD
SPK SIZE
SPK DISTANCE
SPK LEVEL
TEST TONE
DPLII SETUP
TONE CONTROL
A/V SYNC
MP3 ENHANCER
SMART VOLUME
ASC SETUP
DRC SETUP
HDMI SETUP
VARIABLE SET
29
HW-C500-C560S-EUR-0615.indd 29
2010-06-16
3:08:03
Setup
SETUP MENU TREE (Continued)
AUDIO SETUP
SPK SIZE
FRONT
LARGE
SMALL
LARGE
SMALL
NONE
LARGE
SMALL
NONE
YES
NO
CENTER
SURR
SUBW
CROVR
60Hz, 80Hz, 100Hz, 120Hz, 150Hz, 180Hz, 200Hz
SPK DISTANCE
F.L
F.R
CEN
S.L
0.30 ~ 9.00m (0.3m step) , default : 3m
S.R
S.W
SPK LEVEL
F.L
F.R
CEN
S.L
-10 ~ +10dB (1dB step) , default : 00dB
S.R
S.W
TEST TONE
DPLII SETUP
TONE CONTROL
A/V SYNC
MP3 ENHANCER
SMART VOLUME
ASC SETUP
DRC SETUP
HDMI SETUP
VARIABLE SET
AUTO
MANUAL
30
HW-C500-C560S-EUR-0615.indd 30
2010-06-16
3:08:03
ENG
SETUP MENU TREE (Continued)
● SETUP
AUDIO SETUP
SPK SIZE
SPK DISTANCE
SPK LEVEL
TEST TONE
DPLII SETUP
PANORAMA
OFF
ON
DIMENSION
-7 ~ 0 ~ +7
C- WIDTH
0~7
TONE CONTROL
TONE
OFF
ON
BASS
-6dB ~ +6dB (1dB Step)
TREBLE
-6dB ~ +6dB (1dB Step)
A/V SYNC
MP3 ENHANCER
SMART VOLUME
ASC SETUP
DRC SETUP
HDMI SETUP
VARIABLE SET
31
HW-C500-C560S-EUR-0615.indd 31
2010-06-16
3:08:03
Setup
SETUP MENU TREE (Continued)
AUDIO SETUP
SPK SIZE
SPK DISTANCE
SPK LEVEL
TEST TONE
DPLII SETUP
TONE CONTROL
A/V SYNC
SYNC OFF ~ SYNC 240MS (10MS Step)
MP3 ENHANCER
OFF
ON
SMART VOLUME
OFF
ON
ASC SETUP
START
EQ ON / EQ OFF
DRC SETUP
MAX
STD
HDMI SETUP
SYNC
MIN
ON
OFF
AVR
TV
ON
OFF
AUDIO
ANYNET+
VARIABLE SET
OFF
ON
32
HW-C500-C560S-EUR-0615.indd 32
2010-06-16
3:08:03
ENG
SETTING THE SPEAKER SIZE
Signal outputs and frequency response from the speaker will be adjusted according to your speaker configuration and whether
certain speakers are used or not.
● SETUP
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
Æ
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select SPK SIZE, and then press the ENTER
or ► button.
4. Press the ▲▼ buttons to select the speaker you want, and then press
the ENTER or ► button.
• Each time you press the ▲▼ buttons, FRONTÆCENTER Æ SURR Æ
SUBW Æ CROVR will be selected in turn.
Æ
5. Press the ▲▼ buttons to set the mode (LARGE, SMALL etc.) for the
selected speaker.
6. Repeat steps 3-5 to set the mode for each speaker.
- To exit setup mode • Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
Setting the Speaker
SPEAKER
Possible Settings
Default Setting
FRONT (Front)
LARGE, SMALL
SMALL
CENTER (Centre)
LARGE, SMALL, NONE
SMALL
SURR (Surround)
LARGE, SMALL, NONE
SMALL
SUBW (Subwoofer)
YES, NO
YES
CROVR (Crossover Frequency)
60, 80, 100,120, 150, 180, 200(Hz) 100Hz
•
•
•
•
•
•
LARGE : Select when using large speakers. You can listen to full range sound.
SMALL : Select this when using small speakers
NONE : Select when no speaker is used
YES (subwoofer) : Select when using the subwoofer speaker.
NO (subwoofer) : Select when not using the subwoofer speaker.
CROVR : Select the crossover frequency for the best bass response in your room.
M
 You can also use SETUP, ,,., <, >, ENTER on the front of your AV Receiver.
 When the Front speaker is only set to LARGE, you can select LARGE of other speakers.
33
HW-C500-C560S-EUR-0615.indd 33
2010-06-16
3:08:03
Setup
SETTING THE SPEAKER LISTENING DISTANCE
If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of the audio
signals from the centre and surround speakers.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
3. Press the ▲▼ buttons to select SPK DISTANCE, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to select the speaker you want, and then press
the ENTER or ► button.
• Each time you press the ▲▼ buttons, F.L Æ F.RÆ CEN Æ S.L Æ S.R
Æ S.W will be selected in turn.
Æ
5. Press the ▲▼ buttons to set the Speaker Distance.
• For the FRONT LEFT, FRONT RIGHT, CENTER, SURR. LEFT,
SURR. RIGHT and SUBWOOFER Speakers, you can set the distance
from the speaker to listening position between 0.3~9.0m in intervals of
0.3m.
Æ
- To exit setup mode • Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
- Setting Speaker Distance Set the distance from the speaker to listening position in intervals of 0.3m.
• F.L (front left) : 0.3 ~ 9.0 m
• F.R (front right) : 0.3 ~ 9.0 m
• S.L (surround left) : 0.3 ~ 9.0 m
M
• CEN (centre) : 0.3 ~ 9.0 m
• S.R (surround right) : 0.3 ~ 9.0 m
• SW (subwoofer) : 0.3 ~ 9.0 m
 If the listening position is beyond the range of the speaker distance setup, set the speaker distance to the
maximum.
 The distance range of the overall speaker system is determined based on the F.L(front left) speaker
distance from the listening position.
34
HW-C500-C560S-EUR-0615.indd 34
2010-06-16
3:08:04
ENG
SETTING THE SPEAKER LEVEL
You can set the balance and level of speakers.
2. Press the ENTER button to select SETUP ENTER.
● SETUP
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
Æ
3. Press the ▲▼ buttons to select SPK LEVEL, and then press the ENTER
or ► button.
4. Press the ▲▼ buttons to select the speaker you want, and then press the
ENTER or ► button.
• Each time you press this button, F.L Æ F.RÆ CEN Æ S.L Æ S.R Æ
S.W will be selected in turn.
Æ
5. Press the ▲▼ buttons to set the Speaker Level mode.
• You can adjust it from -10 to +10dB in 1 step increments.
• The sound gets quieter at -10dB and louder at +10dB.
Æ
Æ
- To exit setup mode • Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
- Setting Speaker Level • F.L (front left) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
35
HW-C500-C560S-EUR-0615.indd 35
2010-06-16
3:08:04
Setup
SETTING THE TEST TONE
Use the test tone to check the speaker connection status or level.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select TEST TONE, and then press the ENTER
or ► button.
4. Press the ▲▼ buttons to select the option you want, and then press the
ENTER or ► button.
• AUTO : Test signal will be automatically output as follows; F.L Æ CEN
Æ S.W ÆF.R Æ S.R Æ S.L.
- During test tone output, press the ▲▼ buttons to adjust the speaker
output level from -10 to +10 dB by 1 step.
• MANUAL : Enables you to adjust the output level of the speaker
manually.
1) Press the ENTER button to select the speaker you want.
Each time you press the ENTER button, F.L Æ CEN Æ S.W ÆF.R Æ
S.R Æ S.L will be selected in turn.
Æ
Æ
Æ
Æ
2) Press the ▲▼ buttons to set the Test Tone mode you want.
You can adjust the speaker output level from -10 to +10dB by 1 step.
The sound gets quieter at -10dB and louder at +10dB.
- Test Tone Output • F.L (front left) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
• S L (surround left) : -10 ~ +10dB
- To stop test tone • Press the SETUP/MENU button once.
SETUP OFF appears on the display and test tone stops.
36
HW-C500-C560S-EUR-0615.indd 36
2010-06-16
3:08:04
ENG
SETTING DOLBY PRO LOGIC II MODE
This mode provides 5.1 channel sound from 2 channel sources.
Press the PROLOGIC button on the remote control.
• MOVIE : Adds realism to the movie soundtrack.
● SETUP
• MUSIC : Provides 5.1 channel surround sound for digital, analogue or existing stereo sources.
• GAME : Enhances the excitement of the game’s sound.
• MATRIX : You will hear 5.1 channel surround sound.
• PL (Pro Logic) : You will experience a surround effect with 5.1 channel surround sound.
SETTING DOLBY PRO LOGIC II
This function works only in Dolby Pro Logic ll MUSIC mode.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
3. Press the ▲▼ buttons to select DPLII SETUP, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to select the option you want, and then press the
ENTER or ► button.
• PANORAMA : You can set it ON or OFF.
(This mode extends the front stereo image to include the surround
speakers for an exciting "wraparound" effect with side wall imaging.)
• DIMENSION : You can set from -7 to +7.
(Incrementally adjusts the sound field (DSP)from the front or surround.)
• C- WIDTH : You can set from 0 to 7.
(This sets the width of the centre sound image. The higher the setting,
the less sound comes from the center speaker.)
M
Æ
Æ
Æ
 PANORAMA, DIMENSION and CENTER WIDTH settings are enabled only if the mode is set to MUSIC.
 You cannot use Dolby Pro Logic II mode for multi channel signals such as Dolby Digital and DTS.
 Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz or 48KHz.
37
HW-C500-C560S-EUR-0615.indd 37
2010-06-16
3:08:05
Setup
SETTING TONE CONTROL
This will enable you to adjust the bass and treble level.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
3. Press the ▲▼ buttons to select TONE CONTROL, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to select the option you want, and then press
the ENTER or ► button.
• Each time you press this button, TONE Æ BASS Æ TREBLE will be
selected in turn.
Æ
5. Press the ▲▼ buttons to set the Tone Control mode you want.
• If it is set to the TONE OFF, Tone Control function will be disabled.
• You can adjust it from -6 to +6dB by 1 step.
• The sound gets quieter at -6dB and louder at +6dB.
- To exit setup mode • Press the SETUP/MENU button.
SETUP OFF appears on the display and Setup Mode is exited.
M
 The Tone Control function can be applied to all channels except for the subwoofer.
38
HW-C500-C560S-EUR-0615.indd 38
2010-06-16
3:08:05
ENG
AV SYNC
Video may look slower than the audio if it is connected to a digital TV. If this occurs, adjust the audio delay time to
match the video.
2. Press the ENTER button to select SETUP ENTER.
● SETUP
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
Æ
3. Press the ▲▼ buttons to select A/V SYNC, and then press the ENTER
or ► button.
4. Press the ▲▼ buttons to set the A/V Sync mode you want.
• You can adjust it from OFF to 240MS in 10MS steps.
Æ
MP3 ENHANCER
This also helps enhance your sound experience (ex. mp3 music). Use this if you want to hear better sound from a
low quality mp3 source.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
3. Press the ▲▼ buttons to select MP3 ENHANCER, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to select ON or OFF.
Æ
SMART VOLUME
This will regulate and stabilize the volume level against a drastic volume change when changing channels or during a
scene transition.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
3. Press the ▲▼ buttons to select SMART VOLUME, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to select ON or OFF.
Æ
39
HW-C500-C560S-EUR-0615.indd 39
2010-06-16
3:08:05
Setup
ASC (AUTO SOUND CALIBRATION) SETUP
By setting the ASC function just once when you relocate or install the unit, you can have the unit automatically
recognize the distance between speakers, levels between channels, and frequency characteristics to create a 5.1channel sound field optimized for your environment.
- Before Setting 1. Plug the ASC microphone into the ASC MIC jack.
2. Place the ASC microphone at the listening position.
3. Press the ASC button on the front panel, and then press the ENTER button.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
3. Press the ▲▼ buttons to select ASC SETUP, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to select ASC START, and then press the
ENTER button.
• To create the optimal 5.1 channel sound field, the selections are in the
following sequence:
Æ
L ➞ C ➞ R ➞ SR ➞ SL ➞ SW
• EQ ON : The ASC(Auto Sound Calibration) EQ mode is set to on.
EQ OFF: The ASC(Auto Sound Calibration) EQ mode is set to off.
5. If you see a ASC READY message on the screen, press the ENTER button to apply the measurement value.
And then unplug the ASC microphone.
ASC
Microphone
To cancel the ASC (Auto Sound Calibration) setup.
This will be automatically reverted if you press the RETURN button.
* If ASC error occurs, see "ASC Error List" on page 55.
M
Setting the ASC function takes about 3 minutes.
 Because the volume level of the tone is fixed during the ASC setup, you cannot adjust the volume using the volume control.
 If the ASC microphone is disconnected during the ASC setup, the setup will be cancelled.
 You can also press the ASC button on the remote control to use this function.
40
HW-C500-C560S-EUR-0615.indd 40
2010-06-16
3:08:06
ENG
DRC SETUP
● SETUP
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.DRC
compresses the audio to make the loudest sounds quieter and the quietest sounds louder.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP
ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
Æ
3. Press the ▲▼ buttons to select DRC SETUP, and then press the
ENTER or ► button.
4. Press the ▲▼ buttons to set the DRC Setup mode you want.
• STD : Sets DRC effect to standard. • MAX : Sets DRC effect to maximum.
• MIN : Sets DRC effect to minimum.
HDMI SETUP
Use this if you want to receive audio from HDMI connected external devices.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select HDMI SETUP, and then press the ENTER or ► button.
4. Press the ▲▼ buttons to select the option you want, and then press the ENTER or ► button.
5. Press the ▲▼ buttons to set the HDMI Setup mode you want.
• HDMI AUDIO : AVR(Audio Video Receiver), TV
This preference determines whether audio received at the HDMI IN is output by the HDMI OUT.
If you want to listen to audio from an HDMI connected external device through your HDMI connected TV's
speakers, set it to TV. Otherwise, leave it on AVR to listen to audio from the A/V receiver.
- AVR : HDMI audio is not output
- TV : HDMI audio is output
• HDMI ANYNET+ : ON, OFF
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's remote control.
- ON : Anynet+ is enabled.
- OFF : Anynet+ is disabled.
• HDMI SYNC : ON, OFF
The AV receiver can be set to automatically correct any delay between the video and the audio, based on the
data from the connected TV.
- ON : HDMI Sync is enabled.
- OFF : HDMI Sync is disabled
M
 HDMI Audio is enabled only if both the HDMI INPUT and HDMI OUT are connected properly and working normally.
 This function works only if your HDMI-compatible TV supports HDMI Sync.
VARIABLE SET (Low Power Consumption SETUP)
This function enhances electric power efficiency using the variable power with output power.
1. Press the SETUP/MENU button.
• Each time the button is pressed, the mode switches between SETUP ENTER and SETUP OFF.
2. Press the ENTER button to select SETUP ENTER.
3. Press the ▲▼ buttons to select VARIABLE SET, and then press the ENTER or ► button.
4. Press the ▲▼ buttons to select ON or OFF.
• ON :This is Samsung's electric power efficiency function, you can save about 30 % for power consumption.
• OFF: Normal power efficiency function.
M
 This function is not available after the Tone Control, Speaker Level, SFE mode or ASC is changed from the factory setting.
41
HW-C500-C560S-EUR-0615.indd 41
2010-06-16
3:08:07
Operation
USING THE SURROUND MODES
Using the SOUND EFFECT button on the front of the main unit
Selecting the SFE mode
1. Press the SOUND EFFECT button to select SFE.
• Each time you press this button, SFE Æ DPLII will be selected in turn.
2. Press the UP/DOWN ( ,,. ) button.
• Each time you press the UP/DOWN ( ,,. ) button,
STEREO Æ HALL 1 Æ HALL 2 Æ J.CLUB Æ CHURCH Æ ROCK Æ CLASSIC Æ LIVE Æ
GAME Æ MOVIE Æ CONCERT Æ STADIUM will be selected in turn.
• You can also select the SFE mode by pressing the DSP button on the remote control.
Selecting the DPLII mode
1. Press the SOUND EFFECT button to select DPLII.
• Each time you press this button, SFE Æ DPLII will be selected in turn.
2. Press the UP/DOWN ( ,,. ) button.
• Each time you press the UP/DOWN ( ,,. ) button, MUSIC Æ GAME Æ MATRIX Æ PL Æ
MOVIE will be selected in turn.
• You can also select the DPLll mode by pressing the PROLOGIC button on the remote control.
M
You cannot use Dolby Pro Logic ll mode for multi channel signals such as Dolby Digital and DTS.
 Pro Logic works only for BITSTREAM audio signals with sampling frequencies of 32KHz, 44KHz or
48KHz.
Using the S.DIRECT/STEREO button on the front of the main unit
Press the S.DIRECT/STEREO button.
• Each time the button is pressed, the mode switches between the S. DIRECT mode and the STEREO
mode.
• S.DIRECT : Outputs 2 CH PCM audio signal without any signal processing, providing higher audio
quality. This is useful for obtaining the best sound from a connected CD player.
• STEREO : Outputs sound of the selected source in 2 CH stereo.
42
HW-C500-C560S-EUR-0615.indd 42
2010-06-16
3:08:08
ENG
USING THE SURROUND MODES (Continued)
Surround Mode and Input Signal Chart
o = active, – = inactive
DOLBY
(MUSIC, GAME,
MATRIX, PL, MOVIE)
SFE
STEREO
Input Signal
Decoding
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
L.PCM (Audio)
Analogue
Dolby D (2ch)
Dolby D (2ch Surr)
L.PCM (Audio)
Analogue
Dolby D (2ch)
Dolby D (2ch Surr)
L.PCM (Audio)
L.PCM 96KHz
Analogue
Dolby Digital 5.1
Pro Logic II
Pro Logic II
Pro Logic II
Pro Logic II
DD+SFE
DD+SFE
SFE
SFE
Stereo
Stereo
Stereo
Stereo
Stereo
Output Channel
SL
L/R
C
SUBW
SR
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
–
–
O
O
–
–
O
O
–
–
O
O
–
–
O
O
–
–
O
Display Information
Display Signal
Format
DIGITAL
DIGITAL
DIGITAL
L.PCM
Analogue
DIGITAL
DIGITAL
L.PCM
Analogue
DIGITAL
DIGITAL
L.PCM
L.PCM
Analogue
● OPERATION
Surround Mode
Channel Status
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, R, SW
L, R, SW
L, R, SW
L, R, SW
L, R, SW
• L/R : Front Speaker (Left/Right)
C : Centre Speaker
SL/SR : Surround Speaker (Left/Right)
SW : Subwoofer
M
 Channel status displays are dependent on the speaker configuration.
 SFE mode works with 2-ch signals.
USING THE SUBWOOFER SELECTION BUTTON
You can set the subwoofer to on/off.
Press the SUBWOOFER button.
43
HW-C500-C560S-EUR-0615.indd 43
2010-06-16
3:08:08
Operation
LISTENING TO THE RADIO
You can listen to the radio by using either automatic or manual tuning.
1. Press the INPUT SELECT button to select FM.
2. Select a frequency (radio broadcast).
• Preset tuning :
Press the #,$ buttons on the remote control to select the preset frequency.
• Manual tuning 1 (Automatic tuning) :
Press and hold the TUNING/CH ( .,, ) buttons on the remote control to automatically tune in a frequency.
• Manual tuning 2 :
Press the TUNING/CH ( .,, ) buttons on the remote control to increase or decrease the frequency step by
step.
M
 You can also use the SELECT ( .,, ) buttons on the main uint to change the radio frequency.
To Listen in mono/stereo
Press the MO/ST button on the remote control.
• Each time you press this button, STEREO or MONO will be selected in turn.
• If you select MONO in an area with weak reception, it will help to reduce noise.
• This function works only with the remote control.
Presetting radio stations
You can preset up to 30 FM stations.
E.g.: Setting station FM 89.10 in preset 2.
1. Press the INPUT SELECT button to select FM.
2. Press the TUNING/CH ( .,, ) buttons on the remote
control to select 89.10.
• Refer to step 2 above to tune in automatically and manually.
3. Press the MEMORY button on the main unit.
• You can also use the TUNER MEMORY button on the
remote control.
• Tuner number will blink on the display.
4. Press the TUNING/CH ( .,, ) buttons on the remote
control to select preset 2.
• You can select from presets 1 to 30.
5. Press the MEMORY button on the main unit.
• Tuner number will disappear and station 89.10 will be
saved in preset 2.
Æ
Æ
Æ
6. To preset other stations, repeat steps 2 to 5.
To Listen to Preset Station
• Press the TUNING MODE button to select PRESET and press the SELECT ( .,, ) buttons.
44
HW-C500-C560S-EUR-0615.indd 44
2010-06-16
3:08:08
ENG
ABOUT RDS BROADCASTING
Using the RDS (Radio Data System) to receive FM stations
When tuned to an FM station which provides the RDS service, the RDS
indicator lights up on the display.
Description on RDS function
AMP/TV
DIMMER
BD/DVD
1
2
3
PTY-
PTY SEARCH
PTY+
4
5
6
RDS DISPLAY
● OPERATION
RDS allows FM stations to send an additional signal along with their regular program
signals. For example, the stations send their station names, as well as information
about what type of program they broadcast, such as sports or music, etc.
TA
SLEEP
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
• PTY (Program Type) : Displays the type of programme currently being broadcast
• PS NAME (Program Service Name) : Indicates the name of broadcasting station and is composed of 8
characters.
• RT (Radio Text) : Decodes the text broadcast by a station (if any) and is composed of maximum 64
characters.
• CT (Clock Time) : Decodes the real time clock from the FM frequency.Some stations may not transmit PTY, RT
or CT information therefore this may not be displayed in all cases.
• TA (Traffic Announcement) : When "TA ON" displays, it shows that the traffic announcement is in
progress.
M
RDS may not operate correctly if the station tuned is not transmitting RDS signal properly or if the signal
strength is weak.
To show the RDS signals
You can see the RDS signals the station sends on the display.
Press the RDS DISPLAY button while listening to an FM station.
 Each time you press the button, the display change to show you
the following information :
PS NAME RADIO TEXT CLOCK/TIME FREQUENCY
AMP/TV
DIMMER
BD/DVD
1
2
3
PTY-
PTY SEARCH
PTY+
4
5
6
RDS DISPLAY
TA
SLEEP
• PS (Program Service) : While searching, <PS NAME> appears and then the station names will be displayed. <NO PS NAME> appears if no signal is sent.
• RT(RadioText) : while searching, <RADIO TEXT> appears and then text messages the station sends will
be displayed. <NO RT> appears if no signal is sent.
• FREQUENCY : station frequency (non-RDS service)
About characters shown in the display
When the display shows PS,or RT signals,the following characters are used.
• The display window cannot differentiate upper case and lower case letters and always uses upper case letters.
• The display window cannot show accented letters, <A,> for instance, may stands for accented <A’s> like
<À, Â, Ä, Á, Å and Ã.>
45
HW-C500-C560S-EUR-0615.indd 45
2010-06-16
3:08:08
Operation
PTY (Program Type) indication and PTY-SEARCH function
One of the advantages of the RDS service is that you can locate a particular kind of program from the preset channels by
specifying the PTY codes.
To search for a program using the PTY codes
Before you start, remember...
• The PTY Search is only applicable to preset stations.
• To stop searching any time during the process, press PTY SEARCH while searching.
• There is a time limit in doing the following steps. If the setting is cancelled before you finish, start from step 1 again.
• When pressing the buttons on the primary remote control, make sure that you have selected the FM
station using the primary remote control.
1. Press the PTY SEARCH button while listening to an FM
station.
2. Press the PTY- or PTY+ button until the PTY code you want
appears on the display.
RDS DISPLAY
TA
1
2
3
PTY-
PTY SEARCH
PTY+
4
5
6
SLEEP
• The display gives you the PTY codes described to the right.
3. Press the PTY SEARCH button again, while the PTY code
selected in the previous step is still on the display.
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
• The centre unit searches 29 preset FM stations, stops when it finds
the one you have selected, and tunes in that station.
Display
Program Type
Display
Program Type
NEWS
News including an announced opinion
and report
LIGHT M
Light classical music- Classical music
and instrumental and chorus music
AFFAIRS
Several matters including a current incident,
documentary, discussion and analysis.
CLASSICS
Heavy classical music-Orchestra music,
symphony, chamber music and opera
INFO
Information including weights and measures,
returns and forecast, matters interesting the
customer, medical information, etc.
SPORT
EDUCATE
DRAMA
Sports
Education
Drama-Radio serial, etc.
CULTURE
Culture-National or local culture including the religious problem, social science, language, cinema, etc.
SCIENCE
Natural science and technology
OTHER M
Other music - Jazz, R&B country music
WEATHER
Weather
FINANCE
Finance
CHILDREN
SOCIAL
Children’s programmes
Social affairs
RELIGION
Religion
PHONE IN
Phone in
TRAVEL
Travel
LEISURE
Leisure
Others-Speech, amusing program
(quiz, game), interview, comedy and
satirical play, etc.
COUNTRY
Country Music
POP M
Pop music
NATION M
National Music
ROCK M
Rock music
OLDIES
M.O.R.M
Current contemporary music considered
to be “easy listening.”
VARIED
JAZZ
FOLK M
DOCUMENT
Jazz Music
Oldies Music
Folk Music
Documentary
46
HW-C500-C560S-EUR-0615.indd 46
2010-06-16
3:08:09
ENG
USING AN iPod
You can enjoy playback of your iPod using the supplied remote control.
Listening to Music (iPod audio function)
● OPERATION
You can play music files stored in the iPod player by connecting it to the AV
receiver.
1. Connect the iPod dock connector to the iPod jack on the AV
Receiver.
2. Place the iPod in the dock.
• Your iPod is automatically turned on.
3. Press the INPUT SELECT button on the remote control to select
IPOD AUDIO mode.
4. Press the PLAY button on the remote control to play.
• The AV receiver starts playing from the first track of the iPod player.
5. You can use the remote control to control simple playback functions such as the PLAY, PAUSE,
STOP, SKIP (#,$) buttons.
M
See page 26 for compatible iPods.
Compatibility depends on the software version of your iPod.
 You can also select iPod by pressing the iPod button on the remote control.
47
HW-C500-C560S-EUR-0615.indd 47
2010-06-16
3:08:09
Operation
USING AN iPod (Continued)
Watching a Movie (iPod Video function)
You can play video files stored in the iPod player on a TV by connecting it to the AV receiver.
1. Connect the iPod dock connector to the iPod jack on the AV
receiver.
2. In the iPod screen, move to Videos > Settings and set the TV Out
option to On.
3. Place the iPod in the dock.
4. Press the INPUT SELECT button on the remote control to select
IPOD VIDEO mode.
5. Set the AV IN option of the TV connected to the AV receiver to
COMPOSITE.
<iPod Screen>
Follow the iPod onscreen guide through the following steps.
6. Press the S,T buttons on the remote control to select Videos and
press the ENTER button.
7. Press the S,T buttons on the remote control to select Movies and
press the ENTER button.
8. Press the S,T buttons to select the file to play and press the ENTER
button.
• The iPod's video files will be played on the TV screen.
9. You can use the remote control to control simple playback functions
such as the PLAY, PAUSE, STOP, and SKIP (#,$) buttons.
• If you press the PREV button within 3 seconds after the playback,
the player will stop playing and return to the list screen.
If you press the PREV button 3 seconds or later after the playback,
the player will move to the start screen of the current file.
• Press the STOP button to stop playing and return to the list
screen.
• Press the RETURN button to return to the previous menu.
M
<iPod Screen>
You must have the VIDEO (Monitor) output connected to your TV to view iPod video.
 See page 26 for compatible iPods.
Compatibility depends on the software version of your iPod.
 When the current file is played to the end, the next file will not be played automatically.
To play the next file, select a file to play in the list screen of the iPod player.
 No other screen than the playback one will appear on the TV screen. Check other screens on
the iPod player.
48
HW-C500-C560S-EUR-0615.indd 48
2010-06-16
3:08:09
ENG
CONVENIENT FUNCTIONS
Sleep timer function
You can set the time that this unit will shut itself off.
PTY SEARCH
PTY+
5
6
● OPERATION
Press the SLEEP button.
• SLEEP : OFF Æ 15 Æ 30 Æ 45 Æ 60 Æ 90 Æ 120 M (MIN) will be
selected in turn.
PTY-
4
SLEEP
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
To check sleep timer
Press the SLEEP button.
• The remaining time before this unit will shut itself off is shown on the display.
• Pressing the button again changes the sleep time from what you set previously.
To cancel sleep timer
• Press the SLEEP button until SLEEP OFF appears on the display.
Mute function
This function is useful when answering a doorbell or telephone call.
Press the MUTE button.
• MUTE appears on the display.
MUTE
VOL
ASC
TUNING
/CH
To output sound again
Press the MUTE button again.
• MUTE will disappear and sound will output.
Adjust the display
You can adjust the brightness of the display.
Press the DIMMER button.
• Each time you press this button, the brightness changes as follows :
Dark Æ Bright.
INPUT SELECT
TV SOURCE
POWER
AMP/TV
DIMMER
BD/DVD
1
2
3
PTY-
PTY SEARCH
PTY+
RDS DISPLAY
M
TA
SLEEP, Mute and the Adjust Display functions can only be operated with the remote control.
49
HW-C500-C560S-EUR-0615.indd 49
2010-06-16
3:08:10
Operation
Reset function
When the Power is on,
1. Press the MUTE button.
• MUTE appears on the display.
SLEEP
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
2. Press the 9 button five times and then press the ENTER button.
• "INITIAL : NO" appears on the display.
3. Press the ▲▼ buttons to select YES.
• The unit will turn off after 5 seconds.
MUTE
VOL
ASC
TUNER MEMORY
SUBWOOFER
TUNING
/CH
MO/ST
POPUP
SETUP/MENU
INFO
RETURN
EXIT
When the Power is Off,
1. Press and hold the MEMORY button on the front of your AV Receiver
for longer than 5 seconds.
• The POWER LED will blink one time.
M
Using the RESET function will erase all stored settings.
 Do not use this unless necessary.
SOFTWARE UPGRADE
Samsung may offer upgrades for AV Receiver's firmware in the future.
Please visit Samsung.com or contact the Samsung call centre to receive
information about downloading upgrades and using a USB drive.
Upgrades will be possible by connecting a USB drive to the USB port
located on your AV Receiver.
M
 Insert a USB drive containing the firmware upgrade into the USB
port on the back of the main unit.
 Please be careful to not disconnect the power or remove the USB
drive while upgrades are being applied. The main unit will turn off
automatically after completing the firmware upgrade.
When software is upgraded, settings you have made will return to
their default (factory) settings. We recommend you write down your
settings so that you can easily reset them after the upgrade.
 If you failed software upgrade, it is strongly recommended whole USB data format to FAT16 and
retry software upgrade.
 The NTFS USB File System can not be supported.
 Depending on the manufacturer, the USB may not be supported.
50
HW-C500-C560S-EUR-0615.indd 50
2010-06-16
3:08:11
ENG
Miscellaneous
OPERATING YOUR TV WITH THE REMOTE CONTROL
1. Press the POWER button to turn on the TV.
2. Press the AMP/TV button to set the remote to TV mode.
● MISCELLANEOUS
3. Point the remote control toward the TV.
4. While holding down POWER button, enter the code corresponding to your brand of TV.
• If there is more than one code listed for your TV in the table, enter one at a time to determine
which code works.
• If the code matches the TV's code, the TV will be turned off.
5. If TV is turned on or off when you press the POWER button of the remote control, the setting is
completed.
• You can use the TV POWER, VOLUME, CHANNEL, MENU and Numeric buttons (0~9).
M
The remote control may not work on some brands of TVs. Also, some operations may not be
possible depending on your brand of TV.
 The remote control will work with Samsung TVs by default.
51
HW-C500-C560S-EUR-0615.indd 51
2010-06-16
3:08:12
Miscellaneous
OPERATING YOUR TV WITH THE REMOTE CONTROL (Continued)
TV Brand Code List
Brand
Admiral (M.Wards)
A Mark
Anam
AOC
Bell & Howell
(M.Wards)
Brocsonic
Candle
Cetronic
Citizen
CINEMA
Classic
Concerto
Contec
Coronado
Craig
Croslex
Crown
CURTIS MATHES
CXC
Daewoo
Daytron
Dynasty
Emerson
Fisher
Funai
Futuretech
General Electric (GE)
Hall Mark
Hitachi
Inkel
JC Penny
JVC
KTV
KEC
KMC
LG (Goldstar)
Code Number
056, 057, 058
001, 015
001, 002, 003, 004,005,
006, 007, 008, 009, 010,
011, 012, 013, 014
Brand
Luxman
LXI (Sears)
Magnavox
Code Number
Brand
Sylvania
Code Number
018
019, 054, 056, 059, 060,
062, 063, 065, 071
015, 017, 018, 048, 054,
059, 060, 062, 072, 089
Symphonic
Tatung
Techwood
018, 040, 048, 054, 059,
060, 062
061, 095, 096
006
018
001, 018, 040, 048
057, 058, 081
Marantz
Matsui
040, 054
054
Teknika
TMK
003, 015, 018, 025
018, 040
059, 060
018
003
003, 018, 025
097
003
018
046
015
003, 005, 061, 082, 083,
084
062
003
059, 061, 063
003
002, 003, 004, 015,016,
017, 018, 019, 020, 021,
022, 023, 024, 025, 026,
027, 028, 029, 030, 032,
034, 035, 036, 040, 048,
059, 090, 099, 100
040
003
003, 015, 040, 046, 059,
061, 064, 082, 083, 084, 085
MGA
Mitsubishi/MGA
018, 040
018, 040, 054, 059, 060,
075, 101
018
018, 019, 020, 040, 059,
060
003
003
003
006, 007, 008, 009, 054,
066, 067, 073, 074
018
003, 015, 017, 018, 048,
054, 059, 062, 069, 090
015, 017, 018, 040, 048
054, 062, 072, 112, 114,
117, 118
063, 066, 080, 091
015, 018, 059
040
006, 066, 067
Toshiba
019, 057, 063, 071, 101
107, 109, 110, 111, 113
018
059, 060, 069
015, 017, 018, 040, 048,
054, 060, 064
018
040
003
058, 079
001
003, 054
054
054, 109, 114
054
054, 114
054, 112, 114
019, 065, 103
003
003
006, 040, 056, 059, 066,
067, 068
040
015, 018, 050, 059, 069
045
056, 059, 067, 086
070
059, 061, 087, 088
003, 015, 040
015
001, 015, 016, 017, 037,
038, 039, 040, 041, 042,
043, 044, 054, 086
MTC
NEC
Nikei
Onking
Onwa
Panasonic
Penney
Philco
Philips
Pioneer
Portland
Proton
QUASAR
Radio Shack
RCA/Proscan
Realistic
Sampo
Samsung
Sanyo
Scott
Sears
Sharp
Signature 2000
(M.Wards)
Sony
Soundesign
Spectricon
SSS
017, 048, 056, 060, 061,
075
018, 059, 067, 076, 077,
078, 092, 093, 094
003, 019
040
000, 015, 016, 017, 040,
043, 046, 047, 048, 049,
054, 059, 060, 098
019, 061, 065, 101, 102,
103, 104
003, 040, 060, 061
015, 018, 019
015, 057, 064, 101, 105,
106, 115
057, 058
Vidtech
Videch
Wards
Yamaha
York
Yupiteru
Zenith
Zonda
Dongyang
LOWE
FINLUX
YOKO
LOEWE OPTA
PHONOLA
RADIOLA
SCHNEIDER
AKAI
GRUNDIG
054, 112
054
103
108, 109, 113, 119, 120,
121
BLAUPUNKT
SIEMENS
CGE
IMPERIAL
MIVAR
SABA
BANG&OLUFSEN
BRIONVEGA
108
108
113
113
113
114
114
114
FORMENTI
METZ
WEGA
RADIOMARELLI
SINGER
SINUDYNE
TELEFUNKEN
114
114
114
114
114
114
116
050, 051, 052, 053, 055,
101
003, 040
001
018
52
HW-C500-C560S-EUR-0615.indd 52
2010-06-16
3:08:13
ENG
OPERATING YOUR DVD OR BD PLAYER WITH THE REMOTE CONTROL
1. Press the POWER button to turn on the DVD (BD) player.
2. Press the BD/DVD button on the remote control to set the remote to DVD (BD) mode.
4. While holding down POWER button, enter the code corresponding to your brand of DVD (BD).
• If there is more than one code listed for your DVD (BD) in the table, enter one at a time to
determine which code works.
• If the code matches the DVD (BD)'s code, the DVD (BD) will be turned off.
5. If DVD is turned on or off when you press the POWER button of the remote controller, the setting is
completed.
• You can use DVD (BD) POWER, PLAY, PAUSE, STOP, SKIP, MENU and Numeric buttons (0~9).
M
● MISCELLANEOUS
3. Point the remote control toward the DVD (BD).
The remote control may not work on some brands of DVD.
Also, some operations may not be possible depending on your brand of DVD.
 The remote control will work with Samsung DVD (BD) by default.
DVD Brand Code List
Brand
DENON
DOONOON
DMTECH
FISHER
GE
HARMAN/KARDON
JVC
KENWOOD
LG
MAGNAVOX
MITSUBISHI
Code Number
003, 032
019
017
002
006
012
010, 013
008
001
004
005, 016
Brand
ONKYO
OPTIMUS
PANASONIC
PROSCAN
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SONY
THETA DIGITAL
Code Number
004, 014
011
021
006
004, 023
007, 011, 022, 025
006
000, 027
002
015, 020
011
Brand
TOSHIBA
YAMAHA
ZENITH
TAEGWANG
PS2
X-BOX
APEX
Marantz
Code Number
004, 018
009, 033
004, 024
026
028
029
030
031
BD player Brand Code List
Brand
SAMSUNG
M
Code Number
000, 001, 002, 003, 004
 The remote control will control Samsung BD players only.
53
HW-C500-C560S-EUR-0615.indd 53
2010-06-16
3:08:13
Troubleshooting
Before requesting service, please check the following.
Symptom
Check
Remedy
The unit will not turn on.
• Is the power cord plugged into the
outlet?
• Connect the power plug to the
outlet.
A function does not
work when the button is
pressed.
• Is there static electricity in the air?
• Disconnect the power plug and
connect it again.
Sound is not produced.
• Are the speakers and external
components connected properly?
• Is the Mute function on?
• Is the volume set to minimum?
• Is the Speaker Size set incorrectly to
NONE?
• Connect them correctly.
• Press the MUTE button to cancel
the function.
• Adjust the volume.
• Refer to pages 33 to select LARGE,
SMALL or YES.
Picture does not appear
on a TV when the
function is selected.
• Is the external component
connected properly?
• Connect it correctly.
Remote controller does
not work.
• Are the batteries drained?
• Is the distance between remote
control and main unit too great?
• Replace with new batteries.
• Operate at close distance.
The sound from the left/
right channels is
reversed.
• Are the left/right speaker or left/right
• Check the left/right channel and connect
it/them correctly.
Can't receive radio
broadcasts.
• Is FM antenna connected properly?
• Connect the antenna correctly.
• If the input strength of antenna signal
is weak, install the FM antenna in a
place with good reception.
There is no sound from
surround speakers.
• Are the surround speakers
connected properly?
• Is SURR (surround) incorrectly set to
NONE in the Speaker Size?
• Is surround mode set to stereo?
• Refer to pages 14 ~17 to connect them
properly.
• Is the input signal selected properly?
• Only 2 channel signal can select
Dolby Pro Logic II mode. (ex:Dolby
Digital, PCM, 2 channel analogue
input signal.)
Can't select Dolby Pro
Logic ll mode.
input/output cables connected
properly?
• Refer to page 33 to select LARGE or
SMALL.
• Refer to pages 42 ~ 43 to select proper
Surround Mode.
54
HW-C500-C560S-EUR-0615.indd 54
2010-06-16
3:08:13
ENG
Symptom
Remedy
• Is Digital input selected?
● TROUBLESHOOTING
There is no sound when
playing a DTS encoded
DVD.
Check
• Check whether the DVD player is
properly connected and refer to
page 28 to select the digital input.
Product protection function
Heat protection
• The protection function will come on if the main unit or power transformer overheats.
"
" will appear in the display .
This function will come on :
- If speaker terminal is shorted
- If speaker cable is shorted
If there is no problem when you turn the unit on again after turning it off, PROTECTION mark will disappear on the
display and the unit will work properly.
M
 If PROTECTION appears on the display, check whether the speaker terminal is shorted and then turn on
the unit.
ASC Error List
Error No.
VFD Message
Action
E01
HP CONCT
E02
NO MIC
Connect the microphone.
E03
NOISY
Take an appropriate action to reduce the surrounding noise.
E04
MIC LEVL
The speaker is too close to the microphone.
Check the distance between speaker and microphone.
E05
NO FRONT
Check if the front speaker is connected properly.
E07
LEVL OVR
Check the position of each of speaker and microphone.
E08
DIST OVR
The distance between speaker and microphone exceeds the acceptable value.
Check the location of microphone and each speaker.
E13
TIME OVR
Unplug the power cable and plug it back.
Then, perform ASC again.
E14
CODE ERR
Unplug the power cable and plug it back.
Then, perform ASC again.
Disconnect the headphones.
55
HW-C500-C560S-EUR-0615.indd 55
2010-06-16
3:12:25
Appendix
SPECIFICATIONS
GENERAL
FM TUNER
AMPLIFIER
FREQUENCY
RESPONSE
HDMI
VIDEO OUTPUT
Weight
Dimensions (W x H x D)
Operating temperature range
Operating humidity range
Frequency response
Usable sensitivity
S/N ratio
Distortion
Stereo separation
Tuner output level
Rated output
Front speaker(left+right)
Centre speaker
Surround speaker(left+right)
Subwoofer speaker
Input sensitivity/impedance
S/N ratio (analogue input)
Separation (1kHz)
Analogue input
Digital input/96kHz PCM
Input
Output
TV format
Input level/impedance
Output level/impedance
Video frequency response
S/N ratio
5.6 kg
436.9 x 142.2 x 363.2 mm
+5°C~+35°C
10%~75%
87.5~108.0MHz
12dBf
MONO/STEREO 55/55dB
MONO/STEREO 0.3/0.8%
30dB
1kHz, 75kHz Dev
20Hz~20kHz/THD = 0.9%
6 100W/CH
6 100W/CH
6 100W/CH
6 100W/CH
450mV/47k
80dB
60dB
20Hz~20kHz(±3dB)
20Hz ~44kHz(±3dB)
Compatible 1080p
Compatible 1080p
NTSC/PAL
1Vp-p/75 1Vp-p/75 5Hz to 10kHz(-3dB)
60dB
* S/N Ratio, Distortion, Separation and Usable sensitivity are based on measurement using AES (Audio Engineering
Society) guidelines.
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
- For the power supply and Power Consumption, refer to the label attached to the product.
56
HW-C500-C560S-EUR-0615.indd 56
2010-06-16
3:08:13
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Area
Contact Centre ` North America
Canada
1-800-SAMSUNG (726-7864)
Mexico
01-800-SAMSUNG (726-7864)
U.S.A
1-800-SAMSUNG (726-7864)
` Latin America
Argentine
0800-333-3733
0800-124-421
Brazil
4004-0000
Chile
800-SAMSUNG (726-7864)
Nicaragua
00-1800-5077267
Honduras
800-7919267
Costa Rica
0-800-507-7267
Ecuador
1-800-10-7267
El Salvador
800-6225
Guatemala
1-800-299-0013
Jamaica
1-800-234-7267
Panama
800-7267
Puerto Rico
1-800-682-3180
Rep. Dominica 1-800-751-2676
Trinidad &
1-800-SAMSUNG (726-7864)
Tobago
Venezuela
0-800-100-5303
Colombia
01-8000112112
` Europe
0810 - SAMSUNG
Austria
(7267864, € 0.07/min)
Belgium
Czech
Denmark
Finland
France
Germany
Hungary
Italia
Luxemburg
Netherlands
Norway
Poland
Portugal
Slovakia
Spain
Sweden
U.K
Eire
02-201-24-18
800 - SAMSUNG
(800-726786)
70 70 19 70
030 - 6227 515
01 48 63 00 00
01805 - SAMSUNG
(726-7864 € 0,14/Min)
06-80-SAMSUNG (726-7864)
800-SAMSUNG (726-7864)
261 03 710
0900-SAMSUNG
(0900-7267864) (€ 0,10/Min)
815-56 480
0 801 1SAMSUNG (172678)
022-607-93-33
80820-SAMSUNG (726-7864)
0800-SAMSUNG (726-7864)
902 - 1 - SAMSUNG
(902 172 678)
0771 726 7864 (SAMSUNG)
0845 SAMSUNG (7267864)
0818 717100
HW-C500-C560S-EUR-0615.indd 57
Web Site
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/
be (Dutch)
www.samsung.com/
be_fr (French)
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
Area
Switzerland
Contact Centre Web Site
www.samsung.com/ch
0848 - SAMSUNG (7267864, www.samsung.com/
CHF 0.08/min)
ch_fr/ (French)
8-800-77777
www.samsung.com
8000-7267
www.samsung.com
800-7267
www.samsung.com
Lithuania
Latvia
Estonia
` CIS
Russia
Georgia
Armenia
Azerbaijan
Kazakhstan
Uzbekistan
Kyrgyzstan
Tadjikistan
8-800-555-55-55
8-800-555-555
0-800-05-555
088-55-55-555
8-10-800-500-55-500
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
Ukraine
0-800-502-000
Belarus
Moldova
` Asia Pacific
Australia
New Zealand
810-800-500-55-500
00-800-500-55-500
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.ua
www.samsung.com/
ua_ru
1300 362 603
www.samsung.com
0800 SAMSUNG (0800 726 786) www.samsung.com
400-810-5858
China
www.samsung.com
010-6475 1880
www.samsung.com/
hk
Hong Kong
(852) 3698-4698
www.samsung.com/
hk_en/
3030 8282
1800 110011
India
www.samsung.com
1800 3000 8282
1800 266 8282
0800-112-8888
Indonesia
www.samsung.com
021-5699-7777
Japan
0120-327-527
www.samsung.com
Malaysia
1800-88-9999
www.samsung.com
1-800-10-SAMSUNG
(726-7864)
1-800-3-SAMSUNG
Philippines
(726-7864)
www.samsung.com
1-800-8-SAMSUNG
(726-7864)
02-5805777
Singapore
1800-SAMSUNG (726-7864) www.samsung.com
1800-29-3232
Thailand
www.samsung.com
02-689-3232
Taiwan
0800-329-999
www.samsung.com
Vietnam
1 800 588 889
www.samsung.com
` Middle East & Africa
Turkey
444 77 11
www.samsung.com
South Africa
0860-SAMSUNG (726-7864) www.samsung.com
U.A.E
800-SAMSUNG (726-7864)
www.samsung.com
Bahrain
8000-4726
Jordan
800-22273
2010-06-16
3:08:13
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg,
Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive
2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the
environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working
life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please
separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
HW-C500-C560S-EUR-0615.indd 58
2010-06-16
3:08:13