Samsung P50HP User manual

Add to my manuals
102 Pages

advertisement

Samsung P50HP User manual | Manualzz

SyncMaster P50HP ,P50FP ,P63FP

PDP Monitor

User Manual

Safety Instructions

Notational

Note

These safety instructions must be followed to ensure your safety and prevent property damage.

Make sure to read the instructions carefully and use the product in the correct manner.

Warning / Caution

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Notational Conventions

Prohibited

Do not disassemble

Do not touch

Important to read and understand at all times

Disconnect the plug from the outlet

Ground to prevent an electric shock

Power

When not used for extended period of time, set your computer to DPM.

If using screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases

(or countries).

Shortcut to Anti-Afterimage Instructions

Do not use a damaged power cord or plug or a damaged or loose power outlet.

• Otherwise, this may result in electric shock or fire.

Do not touch the power plug with wet hands when removing or plugging the plug into the outlet.

• Otherwise, this may result in electric shock.

Make sure to connect the power cord to a grounded power outlet.

• Otherwise, it may result in electric shock or personal injury.

Safety Instructions

Ensure that the power plug is plugged into the power outlet firmly and correctly.

• Otherwise, this may result in fire.

Do not forcefully bend or pull the power plug and do not place any heavy material on it.

• Otherwise, this may result in fire.

Do not connect multiple appliances to the same power outlet.

• Otherwise, this may cause fire due to overheating.

Do not disconnect the power cord while using the product.

• Otherwise, this may result in damage to the product due to electric shock.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

• This may cause electric shock or fire.

Use only the power cord provided by our company. Do not use the provided power cord of another product.

• Otherwise, this may result in fire or electric shock.

Installation

Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

Ensure that at least two persons lift and move the product.

• Otherwise, it may be dropped and cause personal injury, and/ or damage the product.

When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out.

• Otherwise, it may fall or cause personal injury.

• Use a cabinet or rack of a size appropriate to the product.

DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIG-

ARETTES AND ANY HEATING APPLIANCES NEAR THE

PRODUCT.

• Otherwise, this may result in fire.

Clean

Safety Instructions

Keep heating appliances as far away from the power cord or the product as possible.

• Otherwise, this may result in electric shock or fire.

Do not install it in a badly ventilated location such as a bookcase or closet.

• Otherwise, this may result in fire due to an increase in the internal temperature.

When putting the product down, make sure to put it down softly.

• Otherwise, this may result in damage to the screen display.

Do not place the front of the product on the floor.

• Otherwise, this may result in damage to the screen display.

Ensure that an authorized installation company installs the wall mount.

• Otherwise, it may fall and cause personal injury.

• Make sure to install the specified wall mount.

Install your product in a well ventilated location. Ensure that there is a clearance of more than 10 cm from the wall.

• Otherwise, it may result in fire due to an increase in the internal temperature.

Ensure that the packaging vinyl is kept away from children.

• Otherwise, it may result in serious harm (suffocation) if children play with it.

If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it.

• This may cause damage to the product or the person carrying it.

When cleaning the monitor case or the surface of the PDP screen, wipe with a slightly moistened, soft fabric.

Do not spray cleaner directly onto the surface of the product.

• Otherwise, this may result in the discoloration and distortion of the structure and the screen surface may peel off.

Clean the product using a soft cloth with a monitor cleaner only.

If you must use a cleaner other than the monitor cleaner, dilute it with water at a ratio of 1:10.

Others

Safety Instructions

When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth.

• Otherwise, it may result in fire.

When cleaning the product, make sure to disconnect the power cord.

• Otherwise, it may result in electric shock or fire.

When cleaning the product, disconnect the power cord and clean it softly with a dry cloth.

• (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the product.

Since the product housing is easily scratched, make sure to use the specified cloth only.

• Use the specified cloth adding only a little water. As the product may be scratched if there is any foreign material on the cloth, make sure to shake it thoroughly before using it.

When cleaning the product, do not spray water directly onto the main body of the product.

• Ensure that water does not enter the product and that it is not wet.

• Otherwise, this may result in electric shock, fire or a malfunction.

The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves.

• Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center.

If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center.

• Otherwise, this may result in electric shock or fire.

Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car.

• Otherwise, this may result in electric shock or fire.

When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center.

• Otherwise, this may result in electric shock or fire.

Safety Instructions

If thunder or lightening is occurring, do not touch the power cord or antenna cable.

• Otherwise, this may result in electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

• Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.

Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.

• Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.

Make sure that the ventilating opening is not blocked by a table or curtain.

• Otherwise, it may result in fire due to an increase in the internal temperature.

Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.

• If water or a foreign material enters the product, disconnect the power cord and contact a Service Center.

• This may result in a product malfunction, electric shock, or fire.

Do not use or keep combustible spray or flammable material near the product.

• Otherwise, this may result in an explosion or fire.

Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc).

• If water or foreign material enters the product, disconnect the power cord and contact a Service Center.

• Otherwise, this may result in electric shock or fire.

When using a fixed screen for a long time, an afterimage or stain may occur.

• If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver.

Set a resolution and frequency appropriate to the product.

• Otherwise, your eyesight may be damaged.

When using headphones or earphones, do not turn the volume too high.

• Having the sound too loud may damage your hearing.

Safety Instructions

If you continually move closer to the product screen, your eyesight may be failing.

Take a rest for at least five (5) minutes after using the monitor for one (1) hour.

This reduces the weariness of your eyes.

Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.

• Otherwise, it may fall and cause personal injury and/or damage the product.

• If you use the product in a location exposed to vibrations, it may damage the product and result in fire.

When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product.

• Otherwise, it may result in electric shock or fire.

Ensure that children do not hang onto the product or climb up onto the product.

• The product may fall and cause personal injury or death.

If you do not use the product for a long period of time, disconnect the power cord from the power outlet.

• Otherwise, this may result in overheating or fire due to dust, and may result in fire due to electric shock or leakage.

Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product.

• Your children may hang onto the product causing it to fall and this may result in personal injury or death.

Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach.

• If children have had the battery in their mouths, consult your doctor immediately.

When replacing the battery, insert it with right polarity (+, -).

• Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.

Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.

• Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.

Safety Instructions

The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.

• The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.

Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater.

• This may reduce the lifetime of the product, and may result in fire.

Do not drop any objects onto the product or cause any impact to the product.

• Otherwise, this may result in electric shock or fire.

Do not use a humidifier or kitchen table near the product.

• Otherwise, this may result in electric shock or fire.

When there is a gas leak, do not touch the product or the power plug but ventilate immediately.

• If a spark occurs, it may cause an explosion or fire.

If the product has been turned on for a long time, the display panel becomes hot. Do not touch it.

• Keep the small accessories in a location out of the reach of children.

Be careful when adjusting the angle of the product or the height of the stand.

• This may result in personal injury as your hand or fingers may become caught.

• Also, if you tilt the product too far, it may fall and cause personal injury.

Do not install the product in a location low enough for children to reach.

• Otherwise, it may fall and result in personal injury.

• Since the front part of the product is heavy, install the product on a level and stable surface.

Do not put any heavy objects on the product.

• This may result in personal injury and/or damage to the product.

Introduction

Package Contents

Note

Please make sure the following items are included with your PDP Display.

If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

Checking the Contents of the Package

Remove the lock from the package box, as shown in the figure above.

Lift up the package box by holding the grooves on both sides of the package box.

Check the contents of the package.

Remove the Styrofoam and vinyl cover.

Note

• After unpacking the package, make sure to check the contents of the package.

• Make sure to keep the package box for transporting the product in the future.

Unpacking

Introduction

PDP Display

Manuals

Quick Setup Guide Warranty Card

(Not available in all locations)

Cables

Others

Power Cord

User's Guide

Remote Control Batteries (AAA X 2)

(Not available in all locations)

Ferrite Core for Power

Cord

Sold separately

D-Sub Cable DVI Cable Wall Mount KIT

Semi Stand KIT BNC Cable BNC to RCA Adaptor Jack

(Applicable to the P50HP,

P50FP model only)

To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation instructions.

Ferrite Core (Power Cord)

Your PDP Display

Front

Introduction

• The ferrite cores are used to shield the cables from interference.

• When connecting a cable, open the ferrite core and clip it around the cable near the plug.

SOURCE button [SOURCE]

Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the PDP Display at the time.

[PC] → [DVI] → [AV] → [HDMI] → [Component] → [BNC]

Enter button [ ]

Activates a highlighted menu item.

MENU button [MENU]

Opens the on-screen menu and exits from the menu. Also use to exit the

OSD menu or return to the previous menu.

- VOL+

Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume.

SEL

Moves from one menu item to another vertically or adjusts selected menu values.

/ When OSD is not on the screen, push the button to adjust channel.

Introduction

Power button [ ]

Use this button for turning the PDP Display on and off.

Power indicator

Shows PowerSaver mode by blinking green

Note

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your PDP Display

OFF when it is not needed or when leaving it unattended for long periods.

Remote Control Sensor

Aim the remote control towards this spot on the PDP Display.

Rear

Note

For detailed information concerning cable connections, refer to Connecting Cables under

Setup. The PDP Display 's configuration at the back may vary slightly depending on the PDP

Display model.

POWER IN

The power cord plugs into the PDP Display and the wall plug.

Introduction

RS232C OUT/IN (RS232C Serial PORT)

MDC(Multiple Display Control) Program Port

RGB IN (PC Video Connection Terminal)

Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC)

DVI IN (PC Video Connection Terminal)

Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC)

DVI / PC / HDMI IN [DVI/PC/HDMI AU-

DIO IN] (PC/DVI/HDMI Audio Connection

Terminal (Input))

- R]

AV / COMPONENT AUDIO IN [L- AUDIO

Connect the port of the DVD, VCR (DVD /

DTV Set-Top Box) to the [ L- AUDIO - R ] port of the PDP Display.

AV IN [VIDEO]

Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.

AUDIO OUT

Headphone output terminal.

DVI OUT

Connect a monitor to another monitor through a DVI cable.

Can connect up to 10 PDP display units.

HDMI IN

Connect the HDMI terminal at the back of your PDP Display to the HDMI terminal of your digital output device using a HDMI cable.

Introduction

BNC OUT [R/PR, G/Y, B/PB, H, V]

(BNC Terminal (Output))

BNC (Analog PC) Connection: connecting the R, G, B, H, V ports.

BNC/COMPONENT IN[R/PR, G/Y, B/

PB, H, V]

(BNC/Component Connection Terminal (Input))

Kensington Lock

The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington

Lock for proper use. The locking device has to be purchased separately.

Note

The location of the Kensington Lock may be different depending on its model.

Using the Anti-Theft Kensington Lock

1. Insert the locking device into the Kensington slot on the Monitor and turn it in the locking direction .

2. Connect the Kensington Lock cable.

3. Fix the Kensington Lock to a desk or a heavy stationary object.

Note

See Connecting Cables for further information regarding cable connections.

Remote Control

Note

The performance of the remote control may be affected by a TV or other electronic device operating near the PDP Display , causing a malfunction due to interference with the frequency.

1. POWER

2. Off

3. Number Buttons

4. DEL button

Introduction

POWER

OFF

Number Buttons

DEL

+ VOL -

MUTE

TV/DTV

button

MENU

INFO

Color Buttons

TTX/MIX

STILL

AUTO

S.MODE

MDC

LOCK

SOURCE

ENTER/PRE-CH

CH/P

D.MENU

GUIDE

RETURN

Up-Down Left-Right buttons

EXIT

SRS

MagicInfo

P.MODE

DUAL/MTS

PIP

SWAP

Turns the product On.

Turns the product Off.

Press to change the channel.

The "-" button operates only for DTV. It is used to select

MMS (multi-channel) for a DTV.

5. + VOL -

6. MUTE

7. TV/DTV

8. MENU

9.

10. INFO

11. Color Buttons

12.

13. STILL

14. AUTO

15. S.MODE

16. MDC

17. LOCK

TTX/MIX

18. SOURCE

19. ENTER/PRE-CH

20. CH/P

21. D.MENU

22. GUIDE

Introduction

Adjusts the audio volume.

Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode.

Selects the TV and DTV mode directly.

Opens the on-screen menu and exits from the menu or closes the adjustment menu.

Activates a highlighted menu item.

Current picture information is displayed on the upper left corner of the screen.

Press to add or delete channels and to store channels to the favorite channel list in the “Channel List” menu.

TV channels provide written information services via teletext.

- Teletext Buttons

For more information > TTX / MIX

Press the button once to freeze the screen. Press it again to unfreeze.

Adjusts the screen display automatically in PC mode. By changing the resolution in the control panel, auto function is performed.

When pressing this button, the current mode is displayed at the bottom centre of the screen. The PDP Display has a built-in high fidelity stereo amplifier. Then press the button again to circle through available preconfigured modes.

( Standard → Music → Movie → Speech → Custom )

MDC Quick Launch Button.

Activates or deactivates all function keys on both the remote control and the PDP Display except for the Power and LOCK buttons.

Press the button to change the input signal SOURCE.

Changing the SOURCE is only allowed for external devices that are connected to the monitor at the time.

This button is used to return to the immediately previous channel.

In TV mode, selects TV channels.

DTV menu display

Electronic Program Guide (EPG) display.

Introduction

23. RETURN

24. Up-Down Left-Right buttons

25. EXIT

26. SRS

27. MagicInfo

28. P.MODE

Returns to the previous menu.

Moves from one menu item to another horizontally, vertically or adjusts selected menu values.

Exits from the menu screen.

Selects SRS TruSurround XT mode.

MagicInfo Quick Launch Button.

When you press this button, current picture mode is displayed on the lower center of the screen.

AV / HDMI / TV : P.MODE

The PDP Display has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes. ( Dynamic →

Standard → Movie → Custom )

29. DUAL/MTS

30.

31.

PIP

SWAP

PC / DVI / MagicInfo: M/B (MagicBright)

MagicBright is a feature providing the optimum viewing environment depending on the contents of the image you are watching. Then push button again to circle through available preconfigured modes. (Entertain → Internet → Text → Custom )

DUAL-

STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM

MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV.

MTS-

You can select MTS (Multichannel Television Stereo) mode.

FM Stereo

Audio Type MTS/S_Mode

Mono Mono

Stereo Mono ↔ Stereo

SAP Mono ↔ SAP

Default

Manual

Change

Mono

Every time you press the button, a PIP screen appears.

- This fuction does not work for this PDP Display.

Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window.

- This fuction does not work for this PDP Display.

Mechanical Layout (P50HP, P50FP)

Mechanical Layout

Introduction

PDP Display Head

Introduction

Installation VESA Bracket

• When installing VESA, make sure to comply with the international VESA standards.

• Purchasing VESA Bracket and Installation Information : Please contact your nearest

SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.

• At least 2 persons are needed in order to move the PDP Display.

• SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion.

Dimensions

Notice

For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.

Introduction

Wall Bracket Installation

• Contact a technician for installing the wall bracket.

• SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer.

• This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.

Components

Only use the components and accessories shipped with the product.

Wall Bracket(1) Hinge(Left 1, Right

1)

Plastic

Hanger

(4)

Screw

(A)(11)

Screw

(B)(4)

Wall Bracket Assembly

Note

There are two hinges(left and right). Use the correct one.

1. Insert and tighten the Captive Screw in the direction of the arrow.

When done, mount the wall bracket on the wall.

Anchor

(11)

There are two hinges(left and right). Use the correct one.

A -

B -

C -

D -

Captive Screw

Wall Bracket

Hinge (Left)

Hinge (Right)

Introduction

2. Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.

If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.

A Length between the two locking holes

3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.

To mount the product on the wall bracket

The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same)

1. Remove the 4 screws on the back of the product.

Introduction

2. Insert the screw B into the plastic hanger.

Notice

• Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers.

• Be careful when installing the product on the bracket as fingers can be caught in the holes.

• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.

3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.

4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket.

Introduction

A -

B -

C -

PDP Display

Wall Bracket

Wall

Wall Bracket Angle Adjustment

Adjust the bracket angle to -2° before installing it on the wall.

1. Fix the product to the wall bracket.

2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.

Note

You can adjust the bracket angle between -2° and 15°.

Make sure to use the top center, and not the left or the right side of the product to adjust the angle.

Mechanical Layout (P63FP)

Mechanical Layout

Introduction

PDP Display Head

Wall Bracket Installation

• Contact a technician for installing the wall bracket.

• SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer.

• This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.

Components

Only use the components and accessories shipped with the product.

Wall Bracket(1) Hinge(Left 1, Right

1)

Plastic

Hanger

(4)

Screw

(A)(11)

Screw

(B)(4)

Anchor

(11)

Introduction

Wall Bracket Assembly

Note

There are two hinges(left and right). Use the correct one.

1. Insert and tighten the Captive Screw in the direction of the arrow.

When done, mount the wall bracket on the wall.

There are two hinges(left and right). Use the correct one.

A -

B -

C -

D -

Captive Screw

Wall Bracket

Hinge (Left)

Hinge (Right)

2. Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.

If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.

A Length between the two locking holes

Introduction

3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.

To mount the product on the wall bracket

The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same)

1. Remove the 4 screws on the back of the product.

2. Insert the screw B into the plastic hanger.

Notice

• Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers.

• Be careful when installing the product on the bracket as fingers can be caught in the holes.

• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.

Introduction

3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.

4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket.

A -

B -

C -

PDP Display

Wall Bracket

Wall

Wall Bracket Angle Adjustment

Adjust the bracket angle to -2° before installing it on the wall.

1. Fix the product to the wall bracket.

2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.

Note

You can adjust the bracket angle between -2° and 15°.

Introduction

Make sure to use the top center, and not the left or the right side of the product to adjust the angle.

Connections

Connecting a Computer

Using a Power cord with Earth

• In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.

When un-wiring the earth lead, make sure to disconnect the AC power in advance.

Note

AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the PDP Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your PDP Display.

Connect the power cord for your PDP Display to the power port on the back of the PDP Display. Turn on the power switch.

There are 2 ways to connect the D-sub to your PDP Display. Choose one of the following:

Using the D-sub (Analog) connector on the video card.

• Connect the D-sub to the 15-pin, RGB port on the back of your PDP

Display and the 15 pin D-sub Port on the computer.

Using the DVI (Digital) connector on the video card.

• Connect the DVI Cable to the DVI(HDCP) port on the back of your PDP

Display and the DVI port on the computer.

Using the BNC (Analog) connector on the video card.

Connections

• Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V ports on the back of your PDP Display and the 15 pin D-sub Port on the computer.

Connect the audio cable for your PDP Display to the audio port on the back of your computer.

Note

• Turn on both your computer and the PDP Display.

• The DVI cable is optional.

• Contact a local SAMSUNG Electronics Service Center to buy optional items.

Connecting to Other devices

Using a Power cord with Earth

• In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.

When un-wiring the earth lead, make sure to disconnect the AC power in advance.

Note

AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the PDP Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your PDP Display.

Connecting AV Devices

1. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the PDP Display.

2. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted.

3. Select AV using the SOURCE .

Note

The PDP Display has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the PDP Display is turned on.

Connecting to a Camcorder

Connections

1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the PDP Display.

2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV

IN [VIDEO] on the PDP Display.

3. Select AV for the Camcorder connection using the Source button on the front of the PDP

Display or on the remote control.

4. Then, start the Camcorders with a tape inserted.

Note

The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables.

Connecting a DVD Player

1. Connect a set of audio cables between the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the PDP Display and the AUDIO OUT jacks on the DVD player.

2. Connect a Component cable between the BNC / COMPONENT IN - P

R the PDP Display and the P

R

, Y, P

B

jacks on the DVD player.

, Y, P

B

port on

Connections

Note

• Select Component for the connection to a DVD player using the SOURCE button on the front of the PDP Display or on the remote control.

• Then, start the DVD Player with a DVD disc inserted.

Note

• A component cable is optional.

For an explanation of Component video, consult your DVD manual.

Connecting a DTV Set Top Box

Note

• The connections for a typical Set Top Box are shown below.

1. Connect a Component cable between the BNC / COMPONENT IN - P

R the PDP Display and the P

R

, Y, P

B

jacks on the Set Top Box.

, Y, P

B

port on

2. Connect a set of audio cables between the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the PDP Display and the AUDIO OUT jacks on the Set Top Box.

Note

• Select Component for the connection to a DTV Set Top Box using the SOURCE button on the front of the PDP Display or on the remote control.

Note

• For an explanation of Component video, see your Set Top Box owner's manual.

Connecting Using a HDMI Cable

Connections

Note

• Input devices such as digital DVD are connected to the HDMI IN terminal of the PDP

Display using the HDMI cable.

• You cannot connect a PC to the HDMI IN terminal.

Connecting Using a DVI Cable

Note

• Connect the DVI output terminal of a digital output device to the DVI IN terminal of the

PDP Display using a DVI cable.

• Set the name of DVI input to AV device in Source -> Edit Name Menu.

Connecting to an Audio System

Connections

Note

• Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and

AUDIO OUT [L-AUDIO-R] on PDP Display.

Introduction

A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display.

Main Screen

Click Start > Program > Samsung > MDC System to start the program.

Select a set to see the volume of the selected set within the slider.

Main Icons

Remocon

Safety Lock

Port Selection

Select Button

Info Grid

Display Selection

Control Tools

1. Use the main icons to switch into each screen.

2. Allows you to enable or disable the remote control signal receiving function of the display unit.

3. Set the Safety Lock function.

When setting the Lock function, you can only operate power and lock buttons on the remote control and set.

4. The setting for the PC Serial Port can change. The original value is COM1.

5. Click Select all or Clear to select or clear all displays.

6. Use Grid to view brief information on selected display.

7. Select a display from Display Selection.

8. Use Control Tools to control displays.

<Note> The remote control Enable/Disable function operates whether or not the power is On/Off, and this applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is shut down, the remote control signal receiving function of all displays is initialized to Enable when the

MDC is closed.

Port Selection

1. The Multiple Display Control is originally set to COM1.

2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu.

3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable.

4. The selected port is stored in the program and used for the next program as well.

Power Control

1. Click Power Control of the main icons and the Power Control screen appears.

Info Grid shows some basic information necessary to Power Control.

2. Use the Select All button or Check Box to choose a display to control.

Power Control allows controlling some of the functions of the selected display.

1) Power On/Off

- Turns the power of the selected display On/Off.

2) Volume

- Controls the volume level of the selected display.

It receives the volume value of the selected display from the sets and displays it in the slider.

(When you cancel the selection or choose Select All, the value returns to the default value 10)

3) (Mute On/Off)

- Turns on/off the Mute function of the selected display.

When selecting one set at a time, turn on the Mute function for the selected set.

The Mute function is disabled automatically when you adjust the volume level.

(The values return to the default settings when you undo the selections or choose "Select All".)

The Power Control feature is available for all displays.

The Volume Control and Mute features are available only for the displays whose power status is ON.

Input Source

1. Click Input Source of the main icons and the Input Source control screen appears.

Click Select All or use Check Box to select a display to control.

• TV Mode

• PC Mode

1)

2)

3)

4)

5)

6)

Info Grid shows some basic information necessary to Input Source Control.

PC

- Changes the Input Source of the selected display to PC.

BNC

- Changes the Input Source of the selected display to BNC.

DVI

- Changes the Input Source of the selected display to DVI.

TV

- Changes the Input Source of the selected display to TV.

DTV

- Changes the Input Source of the selected display to DTV.

AV

- Changes the Input Source of the selected display to AV.

7)

8)

S-Video

- Changes the Input Source of the selected display to S-Video.

Component

- Changes the Input Source of the selected display to Component.

9) MagicInfo

- The Input source of MagicInfo works only on MagicInfo model.

10) HDMI

- Changes the Input Source of the selected display to HDMI.

11) Channel

- Channel arrow appears when the Input Source is TV.

TV Source can be selected only in products with TV and controlling channels is allowed only when

Input Source is TV.

The Input Source Control feature is available only for the displays whose power status is ON.

Image Size

PC, BNC, DVI

1. Click Image Size of the main icons and the Image Size control screen appears.

1)

Info Grid shows some basic information necessary to Image Size Control.

( Power Status)

- Shows the power status of the current display.

2) Image Size

- Shows the current Image Size of the display in use.

3) Input

- Shows the current Input Source of the display in use.

4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI.

5) PC Source - When you click Image Size, the PC Source tab first appear.

- The Image Size Control button controls Image Size available for PC, BNC, DVI.

6) Video Source

- Click the Video Source tab to control Image Size for respective Input Source.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Image Size Control is available only for the displays for which power status is ON.

Image Size

TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV

1. Click Image Size of the main icons and the Image Size control screen appears.

Info Grid shows some basic information necessary to Image Size Control.

1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV.

Click Select All or use Check Box to select a display to control.

2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source.

3) Switch Image Size of the selected display randomly.

Note: Auto Wide, Zoom1 and Zoom2 are not available for selection when the input signal type for

Component and DVI (HDCP) is 720p or 1080i.

(The Auto Wide mode is available only for TV, AV, and S-Video.)

4) The screen modes can only be adjusted when a TV (PAL only) is connected and the Image Size item is set to Auto

Wide.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

The Image Size Control feature is available only for the displays whose power status is ON.

Time

1. Click Time of the main icons and the Time Control screen appears.

Info Grid shows some basic information necessary to Time Control.

1) Current Time

- Set the current time for the selected display (PC Time).

- To change the current time, first change the PC Time.

2) On Time Setup

- Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display.

3) Off Time Setup

- Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display.

4) Shows the On Time settings.

5) Shows the Off Time settings.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Time Control is available only for the displays for which the power status is ON.

At On Time Setup, TV Source functions only for TV Model.

At On Time Setup, MagicInfo Source functions only for MagicInfo Model.

PIP

PIP Size

1. Click PIP of the main icons and the PIP control screen appears.

Click Select All or use Check Box to select a display to control.

Info Grid shows some basic information necessary to PIP Size Control.

1) PIP Size

- Shows the current PIP Size of the display in use.

2) OFF

- Turns off the PIP of the selected display.

3) Large

- Turns on the PIP of the selected display and changes the size to Large.

4) Small

- Turns on the PIP of the selected display and changes the size to Small.

5) Double 1

- Turns on the PIP of the selected display and changes the size to Double 1.

6) Double 2

- Turns on the PIP of the selected display and changes the size to Double 2.

7) Double 3 (Picture By Picture)

- Turns on the PBP of the selected display and changes the size to Double 3.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

PIP Size can be controlled with turning on the LCD Display power.

PIP

PIP Source

1. Click PIP of the main icons and the PIP control screen appears.

Info Grid shows some basic information necessary to PIP Source Control.

1) PIP Source

- PIP Source can be controlled with turning on the LCD Display power.

2) PC

- Changes the source of the PIP of the selected display to PC.

3) BNC

- Changes the source of the PIP of the selected display to BNC.

4) DVI

- Changes the source of the PIP of the selected display to DVI.

5) AV

- Changes the source of the PIP of the selected display to AV.

6) S-Video

- Changes the source of the PIP of the selected display to S-Video.

7) Component

- Changes the source of the PIP of the selected display to Component.

8) HDMI

- Changes the source of the PIP of the selected display to HDMI.

Note: Some of the PIP Sources may not be available for selection, depending on the input source type of the Main Screen.

The Input source of MagicInfo works only on MagicInfo model.

The PIP Control feature is available only for the displays whose power status is ON and the PIP function is set to ON.

Settings

Picture

1. Click Settings of the main icons and the Settings Control screen appears.

Info Grid shows some basic information necessary to Settings Control.

When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM."

1) Picture

- Available only for TV, AV, S-Video, Component, HDMI, DTV.

2) Contrast

- Adjusts Contrast of the selected display.

3) Brightness

- Adjusts Brightness of the selected display.

4) Sharpness

- Adjusts Sharpness of the selected display.

5) Color

- Adjusts Color of the selected display.

6) Tint

- Adjusts Tint of the selected display.

- Available only for NT.

7) Color Tone

- Adjusts the Color Tone for the selected display.

8) Color Temp

- Adjusts the Color Temp for the selected display.

9) Brightness Sensor

- Adjusts the Brightness Sensor for the selected display.

10) Dynamic Contrast

- Adjusts the Dynamic Contrast for the selected display.

The Input source of MagicInfo works only on MagicInfo model.

Color Temp is only enabled if the Color Tone is set to Off.

The Input source of TV works only on TV model.

This feature is available only for the displays whose power status is ON and if no selection is made, the factory default is displayed.

Settings

Picture PC

1. Click Settings of the main icons and the Settings Control screen appears.

Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM."

1) Picture PC

- Available only for PC, BNC, DVI.

2) Contrast

- Adjusts Contrast of the selected display.

3) Brightness

- Adjusts Brightness for the selected display.

4) Red

- Adjusts red Color of the selected display.

- Available only for NT.

5) Green

- Adjusts green Color of the selected display.

- Available only for NT.

6) Blue

- Adjusts blue Color of the selected display.

- Available only for NT.

7) Color Tone

- Adjusts the Color Tone for the selected display.

8) Color Temp

- Adjusts the Color Temp for the selected display.

9) Brightness Sensor

- Adjusts the Brightness Sensor for the selected display.

10) Dynamic Contrast

- Adjusts the Dynamic Contrast for the selected display.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Color Temp is only enabled if the Color Tone is set to Off.

This feature is available only for the displays whose power status is ON and if no selection is made, the factory default is displayed.

Settings

Audio

1. Click Settings of the main icons and the Settings Control screen appears.

Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM."

1) Audio

- Controls audio settings for all input sources.

2) Bass

- Adjusts Bass of the selected display.

3) Treble

- Adjusts Treble of the selected display.

4) Balance

- Adjusts Balance of the selected display.

5) SRS TS XT

- SRS TS XT Sound ON/OFF of the selected display.

6) Sound Select

- Select either Main or Sub when PIP is On.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

This feature is available only for the displays whose power status is ON and if no selection is made, the factory default is displayed.

Settings

Image Lock

1. Click Settings of the main icons and the Settings Control screen appears.

Info Grid shows some basic information necessary to Settings Control.

1) Image Lock

- Available only for PC, BNC.

2) Coarse

- Adjusts Coarse of the selected display.

3) Fine

- Adjusts Fine of the selected display.

4) Position

- Adjusts Position of the selected display.

5) Auto Adjustment

- Self-Adjust to the incoming PC signal.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Settings Control is available only for the displays for which the power status is ON.

Maintenance

Lamp Control

1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.

An "Info Grid" showing several basic data items appears.

1) Maintenance

- Allows the Maintenance Control function for all input sources.

2) Auto Lamp Control

- Automatically adjusts the backlight of the selected display at a specified time.

The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control.

3) Manual Lamp Control

- Allows you to adjust the backlight of the selected display regardless of the time.

The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.

The Maintenance Control feature is available only for the displays whose power status is ON.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Maintenance

Scroll

1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.

1) Scroll

- This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time.

2) Pixel Shift

- This allows the screen to be moved finely at the specified time interval.

3) Safety Screen

- The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time. The Interval item is used to set the repetition cycle in hour units and the Time item is used to set the time when the Safety Screen function must be performed.

The Type item can be set to Scroll, Pixel, Bar, Eraser, All White, or Pattern.

4) Safety Screen2

- This function is used to prevent afterimages from occurring. There are five (5) types that you can select and control with this function.

For the Scroll type, the Time item can be set to 1, 2, 3, 4 or 5. For the Bar and Eraser types, it can be set

to 10, 20, 30, 40 or 50. For the All White and Pattern type, it can be set to 1, 5, 10, 20 or 30.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

The Maintenance Control feature is available only for the displays whose power status is ON.

Maintenance

Video Wall

1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.

1) Video Wall

- A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen.

2) Video Wall (Screen divider)

- The screen can be divided into.

You can select a number of screens with a different layout when dividing. z z

Select a mode from Screen divider.

Select a display from Display Selection. z z

The place will be set up by pressing a number in the selected mode.

The MDC program supplied by Samsung supports up to 5x5 LCD Displayes.

3) On / Off

- Turns on/off the Video Wall function of the selected display.

4) Format

- The format can be selected to see a divided screen. z

Full z

Natural

You may not operate this function in MagicInfo.

The Input source of TV works only on TV model.

The Maintenance Control function is available only for the displays where the power status is ON.

Troubleshooting

1. The display you wish to control does not appear on the Power Control Info Grid

- Check the connection of RS232C. (Check if it is properly connected to the Com1 port)

- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict.

- Check if the Display Set ID is a number between 0 and 25. (Adjust using the Display menu)

Note : A Display Set ID must be a value between 0 and 25 .

2. The display you wish to control does not appear on the other Control Info Grids

- Check to see if the display power is ON. (You can check this in Power Control Info Grid)

- Check if you can change the input source of the display.

3. The dialogue box appears repeatedly.

- Check to see if the display you wish to control is selected.

4. Both On Timer and Off Timer have been set but different time is showing.

- Apply current time to synchronize the display clocks.

5. The remote may not function properly when you turn off the remote Function, disconnect the RS-232C cable, or exit the program in an Irregular manner. Rerun the program and turn the remote function again to Restore normal functions.

<Note> This program may malfunction due to problems in communication circuits or interference from electronic appliances nearby.

Settings Value Display In Multiple Display Mode

When there are more than one displays connected, the settings values are displayed as follows.

1. No selection: Displays the Factory Default Value.

2. Selected one display: Fetches and displays the settings value for the selected display.

3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of

ID 1, fetches and displays the value of ID3.

4. Selected all sets using Select All: Returns to the Factory Default Value.

Adjusting the PDP Display

Input

Available Modes

PC / DVI / BNC

AV

HDMI

• Component

Source List

MENU → ENTER → [Input] → ENTER → [Source List] → , → ENTER

Use to select PC, DVI or other external input sources connected to the PDP Display. Use to select the screen of your choice.

1. PC

2. DVI

3. AV

4. HDMI

5. Component

6. BNC

Note

• The direct button on the remote control is the 'SOURCE' button.

Edit Name

MENU → ENTER → [Input] → → ENTER → [Edit Name] → , → ENTER

Adjusting the PDP Display

Name the input device connected to the input jacks to make your input source selection easier.

VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game /

Camcorder / DVD Combo / DHR / PC

Note

• When connecting a PC to the HDMI or DVI terminal, set Edit Name to PC.

• In other cases, set Edit Name to AV.

• However, since 640x480, 720P (1280x720), and 1080p (1920x1080) are common signals for AV and PC, make sure to set the Edit Name in accordance with the input signal.

• The Picture menu changes depending on the input signal and Edit Name.

Picture [PC / DVI/ BNC]

Available Modes

PC / DVI / BNC

AV

• Component

MagicBright

MENU → → ENTER → [Picture] → ENTER → [MagicBright] → , → ENTER

MagicBright is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Entertain, Internet, Text and Custom. Each mode has its own pre-configured brightness value. You can easily select one of the four settings by simply pressing the MagicBright control button.

1. Entertain

High brightness

Adjusting the PDP Display

For watching motion pictures such as a DVD or VCR.

2. Internet

Medium brightness

For working with a mixture of images such as texts and graphics.

3. Text

Normal brightness

For documents or works involving heavy text.

4. Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.

If this is the case, adjust the brightness and contrast by using the OSD menu.

Custom

Contrast

By using the on-screen menus, the contrast and brightness can be changed to your personal preference.

MENU → → ENTER → [Picture] → → ENTER → [Custom]

Note

By adjusting the picture using the Custom function, MagicBright will change to Custom mode.

MENU → → ENTER → [Picture] → → ENTER → [Custom] → ENTER→ [Contrast] →

, → ENTER

Adjusts the Contrast.

Brightness

MENU → → ENTER → [Picture] → → ENTER → [Custom] → → ENTER→ [Brightness] → , → ENTER

Adjusts the Brightness.

Sharpness

MENU → → ENTER → [Picture] → → ENTER → [Custom] → → → ENTER →

[

Sharpness] → , → ENTER

Adjusts the Sharpness.

Adjusting the PDP Display

Color Tone

MENU → → ENTER → [Picture] → → →ENTER → [Color Tone] → , → ENTER

The color tones can be changed.

1. Off

2. Cool

3. Normal

4. Warm

5. Custom

Note

If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp function is disabled.

If you set the Color Tone to Off, the Color Control function is disabled

Color Control

Adjusts individual Red, Green, Blue color balance.

MENU → → ENTER → [Picture] → → → → ENTER → [Color Control]

Note

If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode.

Red

MENU → → ENTER → [Picture] → → → → ENTER → [Color Control] → ENTER →

[

Red] → , → ENTER

Green

MENU → → ENTER → [Picture] → → → → ENTER → [Color Control] → → ENTER

→ [ Green] → , → ENTER

Adjusting the PDP Display

Blue

MENU → → ENTER → [Picture] → → → → ENTER → [Color Control] → → →

ENTER → [Blue] → , → ENTER

Color Temp.

MENU → → ENTER → [Picture] → → → → ENTER → [Color Temp.] → , → ENTER

Image Lock

Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again.

(Available in PC mode only)

MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock]

Coarse

Color Temp. is a measure of the 'warmth' of the image colors.

Note

This function is only enabled if the Color Tone is set to Off.

MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock] → ENTER

→ [ Coarse] → , → ENTER

Fine

Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu.

MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock] → →

ENTER → [Fine] → , → ENTER

Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).

H-Position

MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock] → →

→ ENTER → [H-Position] → , → ENTER

Adjusts the screen location horizontally.

Adjusting the PDP Display

V-Position

MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock] → → →

→ ENTER → [V-Position] → , → ENTER

Adjusts the screen location vertically.

Auto Adjustment

MENU → → ENTER → [Picture] → → → → → → ENTER → [Auto Adjustment ]

The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, the auto function is performed.

(Available in PC mode only)

Note

The direct button on the remote control is the 'AUTO' button.

Signal Balance

This is used to make up for the weak RGB signal transmitted by a long signal cable.

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance]

(Available in PC mode only)

Signal Balance

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → ENTER → [Signal Balance] → , → ENTER

Selects either On or Off with the signal control.

Signal Control

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance]

→ → ENTER → [Signal Control]

1. R-Gain

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal

Balance] → → ENTER → [Signal Control] → ENTER → [R-Gain] → , → ENTER

Adjusting the PDP Display

2. G-Gain

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal

Balance] → → ENTER → [Signal Control] → → ENTER → [G-Gain] → , → ENTER

3. B-Gain

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal

Balance] → → ENTER → [Signal Control] → → → ENTER → [B-Gain] → , →

ENTER

4. R-Offset

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal

Balance] → → ENTER → [Signal Control] → → → → ENTER → [R-Offset] → ,

→ ENTER

5. G-Offset

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal

Balance] → → ENTER → [Signal Control] → → → → → ENTER → [G-Offset] → , → ENTER

6. B-Offset

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal

Balance] → → ENTER → [Signal Control] → → → → → → ENTER → [B-

Offset] → , → ENTER

Size

MENU → → ENTER → [Picture] → → → → → → → → ENTER → [Size] → ,

→ ENTER

Adjusting the PDP Display

The Size can be switched.

1. 16:9

2. 4:3

Picture [ AV / HDMI / DVI / COMPONENT]

Available Modes

PC / DVI / BNC

AV

HDMI / DVI

Component

Mode

MENU → → ENTER → [Picture] → ENTER → [Mode] → , → ENTER

The PDP Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and

"Custom") that are preset at the factory.

Dynamic, Standard, Movie, or Custom can be activated.

1. Dynamic

2. Standard

3. Movie

4. Custom

Note

The direct button on the remote control is the 'P.MODE' button.

Custom

Contrast

By using the on-screen menus, the contrast and brightness can be changed to your personal preference.

MENU → → ENTER → [Picture] → → ENTER → [Custom]

MENU → → ENTER → [Picture] → → ENTER → [Custom] → ENTER→ [Contrast] →

, → ENTER

Adjusting the PDP Display

Adjusts the Contrast.

Brightness

MENU → → ENTER → [Picture] → → ENTER → [Custom] → → ENTER→ [Brightness] → , → ENTER

Adjusts the Brightness.

Sharpness

MENU → → ENTER → [Picture] → → ENTER → [Custom] → → → ENTER→

[

Sharpness] → , → ENTER

Color

Adjusts the picture Sharpness.

MENU → → ENTER → [Picture] → → ENTER → [Custom] → → → → ENTER→

[

Color] → , → ENTER

Tint

Adjusts the picture Color.

MENU → → ENTER → [Picture] → → ENTER → [Custom] → → → → → ENTER

→ [ Tint] → , → ENTER

Adds a natural tone to the display.

Color Tone

MENU → → ENTER → [Picture] → → → ENTER → [Color Tone] → , → ENTER

The color tones can be changed. The individual Color components are also user adjustable.

Adjusting the PDP Display

1. Off

2. Cool2

3. Cool1

4. Normal

5. Warm1

6. Warm2

Note

If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp function is disabled.

Color Temp.

MENU → → ENTER → [Picture] → → → → ENTER → [Color Temp.] → , → ENTER

Color temp. is a measure of the 'warmth' of the image colors.

Note

This function is only enabled if the Color Tone is set to Off.

Size

MENU → → ENTER → [Picture] → → → → → ENTER → [Size] → , → ENTER

The Size can be switched.

1. 16:9 - Sets the picture to 16:9 wide mode.

2. Zoom 1 - Magnifies the size of the picture on the screen.

3. Zoom 2 - Magnifies the size of the picture more than “Zoom 1”.

4. 4:3 - Sets the picture to 4:3 normal mode.

5. Just Scan - Displays the input scenes as they are without any cutoff when HDMI 720p,

1080i, 1080p signals are input.

Note

Certain external devices may feed the display an out of spec signal that may cause cutoff even when using the Just Scan feature.

Adjusting the PDP Display

ZOOM1, ZOOM2 will be unavailabel in HDMI mode.

Note

The Position and Reset functions are available when Zoom1 or Zoom2 is run.

Digital NR (Digital Noise Reduction)

MENU → → ENTER → [Picture] → → → → → → ENTER → [Digital NR] → ,

→ ENTER

Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images.

1. Off

2. On

Film Mode

MENU → → ENTER → [Picture] → → → → → → → ENTER → [Film Mode ] →

, → ENTER

Sound

The Film Mode feature offers you a theater-quality viewing experience.

(In HDMI mode, this function can be available when the input signal is interlaced scan; it cannot be available with progressive scan signal.)

1. Off

2. On

Available Modes

PC / DVI / BNC

AV

HDMI

Adjusting the PDP Display

Mode

• Component

MENU → → → ENTER → [Sound] → ENTER → [Mode] → , → ENTER

Custom

The PDP Display has a built-in high fidelity stereo amplifier.

1. Standard

Selects Standard for the standard factory settings.

2. Music

Selects Music when watching music videos or concerts.

3. Movie

Selects Movie when viewing movies.

4. Speech

Selects Speech when watching a show that is mostly dialogue (i.e., news).

5. Custom

Selects Custom if you want to adjust the settings according to your personal preferences.

The sound settings can be adjusted to suit your personal preferences.

MENU → → → ENTER → [Sound] → → ENTER → [Custom ]

Note

• You can hear the sound even when sound value is set to 0.

• If you adjust sound using Custom function, Mode will turn to Custom mode.

Bass

MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ENTER→ [Bass] → ,

→ ENTER

Emphasizes low frequency audio.

Adjusting the PDP Display

Treble

MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ →ENTER→ [Treble] →

, → ENTER

Emphasizes high frequency audio.

Balance

MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ → →ENTER→ [Balance] → , → ENTER

Allows you to Adjusts the sound balance between the left and right speakers.

Auto Volume

MENU → → → ENTER → [Sound] → → → ENTER → [Auto Volume] → , → ENTER

Reduces the difference in volume control between broadcasters.

1. Off

2. On

SRS TS XT

MENU → → → ENTER → [Sound] → → → → ENTER → [SRS TS XT] → , → ENTER

SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.

1. Off

Adjusting the PDP Display

2. On

Note

The direct button on the remote control is the 'SRS' button.

Setup

Available Modes

PC / DVI / BNC

AV

HDMI

• Component

Language

MENU → → → → ENTER → [Setup] → ENTER → [Language ] → , → ENTER

You can choose one of 13 languages.

Note

The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.

Time

Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer.

MENU → → → → ENTER → [Setup] → → ENTER → [Time ]

Clock Set

MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → ENTER→ [Clock

Set] → , → , → ENTER

Adjusting the PDP Display

Current Time Setting.

Sleep Timer

MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → ENTER→ [Sleep

Timer] → , → ENTER

Turns the PDP Display off automatically at certain times.

1. Off

2. 30

3. 60

4. 90

5. 120

6. 150

7. 180

On Timer

MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → → ENTER→

[

On Timer] → , / , → ENTER

Turns the PDP Display on automatically at a preset time. Controls the mode and the volume level at the time the PDP Display turns on automatically.

Off Timer

MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → → → ENTER

→ [ Off Timer] → , / , → ENTER

Adjusting the PDP Display

Turns the PDP Display off automatically at a preset time.

Menu Transparency

MENU → → → → ENTER → [Setup] → → → ENTER → [Menu Transparency] → ,

→ ENTER

Change the transparency of the background of the OSD.

1. High

2. Medium

3. Low

4. Opaque

Safety Lock PIN

MENU → → → → ENTER → [Setup] → → → → ENTER → [Safety Lock PIN ] →

[0

∼9] → [0∼9] → [0∼9] → [0∼9]

The password can be changed.

• Change Lock Pin :Changes the product pin number.

• Lock On/Off : When it is set to Lock On, the remote control buttons are inactive and the pin number input window will be displayed on the screen. Input the pin number to change the setting to Lock Off. To return to Lock On, change the setting in the Lock On/ Off mode.

Adjusting the PDP Display

Note

The preset password for the PDP Display is "0000"

Initializing the Safety Lock pin number: INFO + EXIT + MUTE

Energy Saving

MENU → → → → ENTER → [Setup] → → → → → ENTER → [Energy Saving] →

, → ENTER

This feature adjusts the power consumption of the unit in order to save energy.

1. Off

2. On

HDMI Black Level

MENU → → → → ENTER → [Setup] → → → → → → ENTER → [HDMI Black

Level ] → , → ENTER

When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected. In this case, adjust the screen quality of your TV by configuring the HDMI black level.

1. Normal

2. Low

Video Wall

A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen.

When the Video Wall is on, you can adjust the Video Wall screen setting.

MENU → → → → ENTER → [Setup] → → → → → → → ENTER → [Video

Wall ]

Adjusting the PDP Display

Note

When Video Wall is running, the Auto Adjustment, Image Lock, and Size functions are not available. Video Wall does not operate in MagicInfo mode.

Video Wall

MENU → → → → ENTER → [Setup] → → → → → → → ENTER → [Video

Wall ]→ ENTER → [Video Wall ] → , → ENTER

Turns Off/On the Video Wall function of the selected display Off/On.

1. Off

2. On

Format

MENU → → → → ENTER → [Setup] → → → → → → → ENTER → [Video

Wall ]→ → ENTER → [Format] → , → ENTER

The Format can be selected to see a divided screen.

1. Full

Provides a full screen without any margins.

2. Natural

Displays a natural image with the original aspect ratio intact.

Horizontal

MENU → → → → ENTER → [Setup] → → → → → → → ENTER → [Video

Wall ]→ → → ENTER → [Horizontal] → , → ENTER

Adjusting the PDP Display

Sets how many parts the screen should be divided horizontally.

Five adjustment levels: 1, 2, 3, 4, and 5.

Vertical

MENU → → → → ENTER → [Setup] → → → → → → → ENTER → [Video

Wall ]→ → → → ENTER → [Vertical] → , → ENTER

Sets how many parts the screen should be divided vertically.

Five adjustment levels: 1, 2, 3, 4, and 5.

Screen Divider

MENU → → → → ENTER → [Setup] → → → → → → → ENTER → [Video

Wall ]→ → → → → ENTER → [Screen Divider]

The screen can be divided into several images. A number of screens can be selected with a different layout when dividing.

• Select a mode in Screen Divider.

• Select a display in Display Selection.

• The selection will be set up by pressing a number in the selected mode.

Safety Screen

The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time.

Adjusting the PDP Display

• The Safety Screen function scrolls the screen for the specified period of time.

• This function is not available when the power is turned off.

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen]

Pixel Shift

Pixel Shift

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → ENTER → [Pixel Shift] → ENTER → [Pixel Shift] → , → ENTER

To prevent after-images on the screen you can use this function, so that every minute pixels on the PDP are moved in horizontal or vertical direction.

1. Off

2. On

Note

The Pixel Shift is not available when Video Wall is On.

Horizontal Dot

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → ENTER → [Pixel Shift] → → ENTER → [Horizontal Dot] → , → ENTER

Sets how many pixels the screen moves horizontally.

Five adjustment levels: 0, 1, 2, 3, and 4.

Vertical Line

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → ENTER → [Pixel Shift] → → → ENTER → [Vertical Line] → , → ENTER

Adjusting the PDP Display

Sets how many pixels the screen moves vertically.

Five adjustment levels: 0, 1, 2, 3, and 4.

Time

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → ENTER → [Pixel Shift] → → → → ENTER → [Time] → , → ENTER

Timer

Timer

Set the time interval for performing the horizontal or vertical movement, respectively.

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → → ENTER → [Timer] → ENTER → [Timer] → , → ENTER

You can set the timer for Screen Burn Protection.

If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish.

1. Off

2. On

Mode

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → → ENTER → [Timer] → → ENTER → [Mode] → , → ENTER

Adjusting the PDP Display

Period

You can change the Safety Screen Type.

1. Scroll

2. Bar

3. Eraser

4. All White

5. Pattern

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → → ENTER → [Timer] → → → ENTER → [Period] → , → ENTER

Time

Use this function to set the execution period for each mode set in the timer.

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → → ENTER → [Timer] → → → → ENTER → [Time] → , → ENTER

Within the set period of time specify a time for execution.

• Mode-Scroll : 1~5 sec

• Mode-Bar, Eraser : 10~50 sec

• Mode-All White, Pattern : 1, 5, 10, 20 30 min

Adjusting the PDP Display

Scroll

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → → → ENTER → [Scroll]

Bar

This function prevents after-images on the screen by moving all the pixels on the PDP according to a pattern.

Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time.

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → → → →ENTER → [Bar]

Eraser

This function prevents after-images on the screen by moving long black and white vertical lines.

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → → → → →ENTER → [Eraser]

All White

This function prevents after-images on the screen by moving a rectangular pattern.

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → → → → → →ENTER → [All White]

Adjusting the PDP Display

Pattern

This function prevents after-images on the screen by changing the color of pixels to white.

Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time.

MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety

Screen] → → → → → → →ENTER → [Pattern]

This function prevents after-images on the screen by moving a diagonal pattern stored in the panel repeatedly.

Resolution Select

MENU → → → → ENTER → [Setup] → → → → → → → → →ENTER →

[

Resolution Select ] → , → ENTER

When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution.

Note

Available in PC mode only

1. Off

2. 1024 X 768

Adjusting the PDP Display

3. 1280 X 768

4. 1360 x 768

5. 1366 X 768

Note

Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz,

1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x768 @ 60Hz.

Power On Adjustment

MENU → → → → ENTER → [Setup] → → → → → → → → → → ENTER

→ [ Power On Adjustment ] → , → ENTER

Adjusts the Power On time for the screen.

Caution: Set the Power On time to be longer to avoid overvoltage.

Side Gray

MENU → → → → ENTER → [Setup] → → → → → → → → → → →

ENTER → [Side Gray] → , → ENTER

Select the brightness of the grey for the screen background.

1. Off

2. Light

3. Dark

Reset

Reverts the product settings to factory defaults. The Reset function is only available when

PC / DVI is being used.

Adjusting the PDP Display

MENU → → → → ENTER → [Setup] → → → → → → → → → → →

→ ENTER → [Reset ]

Image Reset

MENU → → → → ENTER → [Setup] → → → → → → → → → → →

→ ENTER → [Reset ]→ ENTER → [Image Reset ] → , → ENTER

Note

Available in PC mode only

Note

The Reset function is not available when Video Wall is On.

Color Reset

MENU → → → → ENTER → [Setup] → → → → → → → → → → →

→ ENTER → [Reset ]→ → ENTER → [Color Reset ] → , → ENTER

OSD Rotation

MENU → → → → ENTER →

→ → → → ENTER → [OSD Rotation ]

→ → → → → → → → → →

→ , → ENTER

OSD Rotate

1. Landscape

2. Portrait

Multi Control

Available Modes

PC / DVI / BNC

AV

HDMI

Component

Adjusting the PDP Display

Multi Control

Assigns an individual ID to the SET.

MENU → → → → → ENTER → [Multi Control ] → ENTER → , → [0~9]

• ID Setup

Assigns distinctive IDs to the SET.

• ID Input

Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated.

Troubleshooting

Self-Test Feature Check

Note

Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself.

Self-Test Feature Check

1. Turn off both your computer and the PDP Display.

2. Unplug the video cable from the back of the computer.

3. Turn on the PDP Display.

The figure shown below ("Check Signal Cable") appears on a black background when the PDP Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen.

4. Turn off your PDP Display and reconnect the video cable; then turn on both your computer and the PDP Display

If your PDP Display screen remains blank after using the previous procedure, check your video controller and computer system; your PDP Display is functioning properly.

Warning Messages

You can even view the screen at a resolution of 1360(1920) x 768(1080). However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. And if the resolution is more than 85Hz, you will see the black screen because the PDP Display does not support over 85Hz.

Note

Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the PDP Display.

Maintenance and Cleaning

1) Maintaining the PDP Display Case.

Clean with a soft cloth after disconnecting the power cord.

Troubleshooting

• Do not use benzene, thinner or other flammable substances, or a wet cloth.

• We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen.

2) Maintaining the Flat Panel Display Screen.

Clean with a soft cloth (cotton flannel) smoothly.

• Never use acetone, benzene or thinner.

(They may cause flaws or deformation of the screen surface.)

• The user will be required to pay costs and related expenses for repairing damages caused.

Symptoms and Recommended Actions

Note

A PDP Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the PDP Display to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer.

1. Check if the power cord and the video cables are properly connected to the computer.

2. Check if the computer beeps more than 3 times when booting.

(If it does, request an a service for the main board of the computer.)

3. If you installed a new video card or if you assembled the PC, check if you installed the

Adaptor(video).

4. Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz.

(Do not exceed 60Hz when using the maximum resolution.)

5. If you have problems in installing the Adaptor (video) driver, boot the computer in Safe

Mode, remove the Display Adaptor in the "Control Panel −> System −> Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver.

Check List

Note

• The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.

Problems related to the Installation (PC Mode)

Note

Problems related to the PDP Display installation and their solutions are listed.

Q: The PDP Display screen flickers.

Troubleshooting

A: Check if the signal cable between the computer and the PDP Display is securely connected.

(Refer to Connecting a Computer)

Problems related to the Screen

Note

Problems related to the PDP Display screen and their solutions are listed.

Q: The screen is blank and the power indicator is off.

A: Ensure that the power cord is firmly connected and the PDP Display is on.

(Refer to the Connecting a Computer)

Q: "Check Signal Cable" message.

A: Ensure that the signal cable is firmly connected to the PC or video sources.

(Refer to the Connecting a Computer)

A: Ensure that the PC or video sources are turned on.

Q: "Not Optimum Mode" message.

A: Check the maximum resolution and the frequency of the video Adaptor.

A: Compare these values with the data in the Preset Timing Modes Chart.

Q: The picture rolls vertically.

A: Check if the signal cable is securely connected. Re-connect it, if necessary.

(Refer to Connecting a Computer)

Q: The image is not clear; picture is blurred.

A: Run Frequency Coarse and Fine tuning.

A: Turn on again after removing all accessories (video extension cable, etc.)

A: Set the resolution and frequency to the recommended ranges.

Q: The picture image is unstable and shakes.

A: Check if the resolution and frequency set for the computer video card falls in the range supported by the PDP Display. If not, reset them referring to the current Information under the PDP Display menu and Preset Timing Modes.

Q: Ghost images are shown in the picture.

A: Check if the resolution and frequency set for the computer video card falls in the range supported by the PDP Display. If not, reset them referring to the current Information under the PDP Display menu and Preset Timing Modes.

Q: The image is too light or too dark.

A: Adjusts the brightness and contrast.

(Refer to the Brightness, Contrast)

Troubleshooting

Q: The screen color is inconsistent.

A: Adjust color using Custom under OSD Color Adjustment menu.

Q: The color image is distorted by dark shadows.

A: Adjust color using Custom under OSD Color Adjustment menu.

Q: The color white is poor.

A: Adjust color using Custom under OSD Color Adjustment menu.

Q: The Power Indicator blinks.

A: The PDP Display is currently saving the changes made in the settings to the OSD memory.

Q: The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. The

PDP Display is using its power management system. Press any key on the keyboard.

A: The PDP Display is using its power management system. Press a key on the keyboard.

Q: The screen is blank and it is blinking.

A: If you see the "TEST GOOD" message on the screen when you pressing the MENU button, check the cable connection between the PDP Display and the computer to ensure that the connector is properly connected.

Problems related to Audio

Note

Problems related to audio signals and their solutions are listed below.

Q: No sound.

A: Ensure that the audio cable is firmly connected to both the audio-in port on your PDP

Display and the audio-out port on your sound card.

(Refer to the Connecting a Computer)

A: Check the volume level.

Q: The sound level is too low.

A: Check the volume level.

A: If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program.

Q: The sound is too high or too low.

A: Adjusts the Treble and Bass to the appropriate levels.

Problems related to the Remote Control

Note

Problems related to the remote control and their solutions are listed.

Q: The remote control buttons do not respond.

A: Check the polarities (+/-) of the batteries.

Troubleshooting

A: Check if the batteries are empty.

A: Check if the power is on.

A: Check if the power cord is securely connected.

A: Check if a special fluorescent or neon lamp is on in the vicinity.

Q & A

Q: How can I change the frequency?

A: The frequency can be changed by reconfiguring the video card.

Note

That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)

Q: How can I Adjusts the resolution?

A: Windows XP:

Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.

A: Windows ME/2000:

Set the resolution in the Control Panel → Display → Settings.

* Contact the video card manufacturer for details.

Q: How can I set the Power Saving function?

A: Windows XP:

Set the resolution in the Control Panel → Appearance and Themes → Display → Screen

Saver.

Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer

Manual).

A: Windows ME/2000:

Set the resolution at the Control Panel → Display → Screen Saver.

Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer

Manual).

Q: How can I clean the outer case/PDP Panel?

A: Disconnect the power cord and then clean the PDP Display with a soft cloth, using either a cleaning solution or plain water.

Do not leave any detergent or scratches on the case. Do not let any water enter the

PDP Display.

Q: How can I play the video?

A: The video supports the MPEG1 and WMV codecs only. Install the corresponding codec to play the video. Note that some of the codecs can be incompatible.

Troubleshooting

Note

Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.

Specifications

General

General

Model Name SyncMaster P50HP / SyncMaster P50FP / SyncMaster

P63FP

PDP Panel

Size

Display area

Pixel Pitch

SyncMaster

P50HP

SyncMaster

P50FP

SyncMaster

P63FP

SyncMaster

P50HP

SyncMaster

P50FP

SyncMaster

P63FP

SyncMaster

P50HP

SyncMaster

P50FP

SyncMaster

P63FP

50 " Diagonal (126 cm)

50 " Diagonal (126 cm)

63 " Diagonal (160 cm)

1105.65 mm (H) x 622.1 mm (V)

1105.65 mm (H) x 622.1 mm (V)

1393.92 mm (H) x 784.1 mm (V)

0.810 mm (H) x 0.810 mm (V)

0.576 mm (H) x 0.576 mm (V)

0.726 mm (H) x 0.726 mm (V)

Synchronization

Horizontal

Vertical

Display Color

16.7 M

30 ~ 81 kHz

56 ~ 75 Hz

Resolution

Optimum resolution

P50HP

Maximum resolution

P50FP

P63FP

P50HP

P50FP

P63FP

1360 x 768 @ 60 Hz (Depends on graphics card used)

1920 x 1080 @ 60 Hz

1920 x 1080 @ 60 Hz

1920 x 1080 @ 60 Hz

1920 x 1080 @ 60 Hz

1920 x 1080 @ 60 Hz

Input Signal, Terminated

RGB Analog, DVI Compliant Digital RGB

0.7 Vp-p ±5 %

Specifications

Input Signal, Terminated

Separate H/V sync, Composite, SOG(Option)

TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)

Maximum Pixel Clock

165MHz (Analog,Digital)

Power Supply

AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz

Signal connectors

D-sub, DVI-D, BNC, AV(Composite, CVBS), HDMI, RS232C In/Out

PC Audio In, Audio In(Stereo), Audio Out(Stereo)

Dimensions (W x H x D) / Weight

SyncMaster P50HP 1204.6 x 724.1 x 97.1 mm (47.4 x 28.5 x 3.8 inch) (Without

Stand) / 32.7 kg (72.1 lbs)

1204.6 x 773.2 x 362.4 mm (47.4 x 30.4 x 14.3 inch) (With

Stand)

SyncMaster P50FP 1204.6 x 724.1 x 97.1 mm (47.4 x 28.5 x 3.8 inch) (Without

Stand) / 33.7 kg (74.3 lbs)

1204.6 x 773.2 x 362.4 mm (47.4 x 30.4 x 14.3 inch) (With

Stand)

SyncMaster P63FP 1503.5 x 894.0 x 99.4 mm (59.2 x 35.2 x 3.9 inch) (Without

Stand) / 51.8 kg (114.2 lbs)

VESA Mounting Interface

SyncMaster P50HP 600 x 400 mm

SyncMaster P50FP 600 x 400 mm

SyncMaster P63FP 676 x 407 mm

Environmental considerations

Operating Temperature : 32°F ~ 104°F (0°C ~ 40°C)

Reliability - MTBF

Storage

Humidity : 10 % ~ 80 %, non-condensing

More than 50,000 hours at 90% confidence level.

Temperature : -4°F ~ 113°F (-20°C ~ 45°C)

Humidity : 5 % ~ 95 %, non-condensing

Audio Characteristics

Audio Input

Audio Output

PC Audio Input

Frequency

Response

RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB)

RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB)

3.5 øStereo Jack, 0.5 Vrms (-9 dB)

RF: 80 Hz ~ 15 kHz (at -3 dB)

A/V: 80 Hz ~ 20 kHz (at -3 dB)

Specifications

Plug and Play Capability

This PDP Display can be installed on any Plug & Play compatible system. The interaction of the PDP Display and the computer systems will provide the best operating conditions and PDP Display settings. In most cases, the PDP Display installation will proceed automatically, unless the user wishes to select alternate settings.

Dot Acceptable

PDP panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of

RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.

For example, the number of PDP sub pixels contained in this product are 3,133,440

(P50HP).

For example, the number of PDP sub pixels contained in this product are 6,220,800

(P50FP, P63FP).

Note

Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)

PowerSaver

This PDP Display has a built-in power management system called PowerSaver. This system saves energy by switching your PDP Display to low-power mode when it has not been used for a certain amount of time. The PDP Display automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your PDP Display OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.

PowerSaver

State

Power Indicator

P50HP

Power Consumption

P50FP

P63FP

Normal Operation

Power saving mode

On, Blinking

Power off

EPA/ENERGY

2000

Off On

350 W

420 W

560 W

Less than 2 watts

Less than 1 watts

Specifications

This monitor is EPA ENERGY STAR equipped with VESA DPM functionality.

® compliant and

ENERGY 2000 compliant when used with a computer

As an ENERGY STAR ® Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

®

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.

SyncMaster P50HP

Display Mode

IBM, 640 x 350

IBM, 640 x 480

IBM, 720 x 400

MAC, 640 x 480

MAC, 832 x 624

MAC, 1152 x 870

VESA, 640 x 480

VESA, 640 x 480

VESA, 800 x 600

VESA, 800 x 600

VESA, 800 x 600

VESA, 800 x 600

VESA, 1024 x 768

VESA, 1024 x 768

VESA, 1024 x 768

VESA, 1152 x 864

VESA, 1280 x 960

VESA, 1280 x 1024

VESA, 1280 x 1024

37.879

48.077

46.875

48.363

56.476

60.023

67.500

60.000

63.981

79.976

Horizontal

Frequency

(kHz)

31.469

31.469

31.469

35.000

49.726

68.681

37.861

37.500

35.156

Vertical Frequency (Hz)

Pixel Clock

(MHz)

70.086

59.940

70.087

66.667

74.551

75.062

72.809

75.000

56.250

60.317

72.188

75.000

60.004

70.069

75.029

75.000

60.000

60.020

75.025

25.175

25.175

28.322

30.240

57.284

100.000

31.500

31.500

36.000

40.000

50.000

49.500

65.000

75.000

78.750

108.000

108.000

108.000

135.000

Sync Polarity

(H/V)

+/+

+/+

+/+

-/-

-/-

-/-

-/-

+/+

+/-

-/-

-/+

-/-

-/-

-/-

+/+

+/+

+/+

+/+

+/+

SyncMaster P50FP / SyncMaster P63FP

Display Mode

IBM, 640 x 350

IBM, 640 x 480

IBM, 720 x 400

Horizontal

Frequency

(kHz)

31.469

31.469

31.469

Vertical Frequency (Hz)

70.086

59.940

70.087

Pixel Clock

(MHz)

25.175

25.175

28.322

Sync Polarity

(H/V)

+/-

-/-

-/+

Specifications

Display Mode

MAC, 640 x 480

MAC, 832 x 624

MAC, 1152 x 870

VESA, 640 x 480

VESA, 640 x 480

VESA, 800 x 600

VESA, 800 x 600

VESA, 800 x 600

VESA, 800 x 600

VESA, 848 x 480

VESA, 1024 x 768

VESA, 1024 x 768

VESA, 1024 x 768

VESA, 1152 x 864

VESA, 1280 x 768

VESA, 1280 x 960

VESA, 1280 x 1024

VESA, 1280 x 1024

VESA, 1360 x 768

VESA, 1600 x 1200

VESA, 1920 x 1080

Horizontal

Frequency

(kHz)

35.000

49.726

68.681

37.861

37.500

35.156

37.879

48.077

46.875

31.020

48.363

56.476

60.023

67.500

47.776

60.000

63.981

79.976

47.712

75.000

66.587

Vertical Frequency (Hz)

Pixel Clock

(MHz)

66.667

74.551

75.062

72.809

75.000

56.250

60.317

72.188

75.000

60.000

60.004

70.069

75.029

75.000

59.870

60.000

60.020

75.025

60.015

60.000

59.934

30.240

57.284

100.000

31.500

31.500

36.000

40.000

50.000

49.500

33.750

65.000

75.000

78.750

108.000

79.500

108.000

108.000

135.000

85.500

162.000

138.500

Sync Polarity

(H/V)

+/+

-/-

-/-

+/+

+/+

+/+

+/+

+/+

-/-

-/-

-/-

-/-

-/-

+/+

+/+

+/+

+/-

+/+

-/+

+/+

+/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the

Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.

Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical Frequency or Refresh Rate. Unit:

Hz

Information

For Better Display

Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for PDP.

• Resolution: 1360 x 768 (P50HP)

Resolution: 1920 x 1080 (P50FP , P63FP)

• Vertical frequency (refresh rate): 60 Hz

PDP panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without any problems.

• For example, the number of PDP sub pixels contained in this product are

3,133,440 (P50HP) / 6,220,800 (P50FP, P63FP).

When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the

PDP area but rub softly. If excessive force is applied, you may stain it.

If you are not satisfied with the picture quality, you can get better quality of picture by performing the "Auto Adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after the automatic adjustment, use the Fine/Coarse adjustment function.

When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time.

PRODUCT INFORMATION (Image Retention Free)

What is Image Retention ?

Image retention may not occur when a PDP panel is operated under normal conditions.Normal conditions are defined as continuously changing video patterns.

When the PDP panel is operated for a long time with a fixed pattern .

Phosphor degradation may occur and the brightness is decreased. To prevent this, the video pattern should be changed from time to time.

When viewing a still screen for a long time, the brightness of any part which was bright in the previous fixed pattern becomes lower than that of its surroundings.

Information

Power Off, Screen Saver, or Power Save Mode

• Turn the power off for 4 hours after 20 hours in use

• Turn the power off for 2 hours after 12 hours in use

• Set the Monitor to power off with the PC Display Properties Power Scheme.

• Use a Screen saver if possible - Screen saver in one color or a moving image is recommended.

Change the Color Information periodically

Note

Use Two different colors

Rotate the Color Information with 2 different colors every 30 minutes.

• Avoid using a combination of characters and background color with large difference in luminance.

Avoid using Grey colors, which can cause Image retention easily.

Avoid: Colors with big difference in luminance (Black & White, Grey)

Change the characters color periodically

Information

• Use Bright colors with little difference in luminance.

- Cycle : Change the characters color and background color every 30 minutes

• Every 30 minutes, change the characters with movement.

• All area display Moving image together with Logo periodically.

- Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.

• The best way to protect your monitor from Image retention is to turn Power off, or set your PC, or System to operate a Screen Saver program when you are not using it. Also Warranty service will be limited based on instruction guide.

Apply the Screen Scroll function on Product

• Apply the Screen Scroll function

- Symptom: Horizontal Bar with Black Color move up and down.

- Select method

• Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Screen Scroll

• Time Interval : 1 ~ 10 hours ( Recommend : 1 )

• Time Period : 1 ~ 5 second ( Recommend : 5 )

Note

( Please check CD's User Guide at "OSD Function", some model's will not available )

Apply the Screen Pixel function on Product

• Apply the Screen Pixel function

- Symptom: Dot with Black Color move up and down.

Information

- Select method

• Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Pixel

• Time Interval : 1 ~ 10 hours ( Recommend : 1 )

• Time Period : 10 ~ 50 second ( Recommend : 50 )

• Apply the Screen Bar function

- Symptom: Horizontal / Vertical Bar with Black Color move up and down.

- Select method

• Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Bar

• Time Interval : 1 ~ 10 hours ( Recommend : 1 )

• Time Period : 10 ~ 50 second ( Recommend : 50 )

Note

( Please check CD's User Guide at "OSD Function", some model's will not available. )

Apply the Screen Erasing function on Product

• Apply the Screen Erasing function

- Symptom: 2 Vertical blocks move with erasing the display

- Select method

• Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser

Information

• Time Interval : 1 ~ 10 hours ( Recommend : 1 )

• Time Period : 10 ~ 50 second ( Recommend : 50 )

Note

( Please check CD's User Guide at "OSD Function", some model's will not available )

Appendix

Contact SAMSUNG WORLDWIDE

Note

If you have any questions or comments relating to Samsung products, please contact the

SAMSUNG customer care center.

U.S.A

CANADA

MEXICO

North America

1-800-SAMSUNG(726-7864) http://www.samsung.com/us

1-800-SAMSUNG(726-7864) http://www.samsung.com/ca

01-800-SAMSUNG

(726-7864) http://www.samsung.com/mx

ARGENTINA

BRAZIL

Latin America

0800-333-3733

0800-124-421 http://www.samsung.com/ar http://www.samsung.com/br

CHILE

COLOMBIA

COSTA RICA

ECUADOR

EL SALVADOR

GUATEMALA

HONDURAS

4004-0000

800-SAMSUNG(726-7864) http://www.samsung.com/cl

01-8000112112

0-800-507-7267 http://www.samsung.com/co http://www.samsung.com/latin

1-800-10-7267

800-6225

1-800-299-0013

800-7919267 http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin

JAMAICA

NICARAGUA

PANAMA

PUERTO RICO

1-800-234-7267

00-1800-5077267

800-7267

1-800-682-3180 http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin

REP. DOMINICA

TRINIDAD & TO-

BAGO

VENEZUELA

1-800-751-2676 http://www.samsung.com/latin

1-800-SAMSUNG(726-7864) http://www.samsung.com/latin

0-800-100-5303 http://www.samsung.com/latin

AUSTRIA

Europe

0810 - SAMSUNG (7267864,

€ 0.07/min) http://www.samsung.com/at

Appendix

BELGIUM 02 201 2418

CZECH REPUBLIC 800 -

(800-726786)

Europe http://www.samsung.com/be

(Dutch)

SAMSUNG http://www.samsung.com/ be_fr (French) http://www.samsung.com/cz

DENMARK

EIRE

FINLAND

FRANCE

GERMANY

8 - SAMSUNG (7267864)

0818 717 100

30 - 6227 515

01 4863 0000

01805 - SAMSUNG

(7267864, € 0.14/Min) http://www.samsung.com/dk http://www.samsung.com/ie http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de

HUNGARY

ITALIA

LUXEMBURG

06-80-SAMSUNG (726-7864) http://www.samsung.com/hu

800-SAMSUNG (726-7864) http://www.samsung.com/it

02 261 03 710

NETHERLANDS 0900-SAMSUNG

(0900-7267864) (€ 0,10/Min) http://www.samsung.com/lu http://www.samsung.com/nl

NORWAY

POLAND

3 - SAMSUNG (7267864)

0 801 1SAMSUNG (172678) http://www.samsung.com/no http://www.samsung.com/pl

PORTUGAL

022 - 607 - 93 - 33

808 20 - SAMSUNG

(7267864) http://www.samsung.com/pt

SLOVAKIA

SPAIN

0800-SAMSUNG (726-7864) http://www.samsung.com/sk

902 - 1 - SAMSUNG(902 172

678) http://www.samsung.com/es

SWEDEN

SWITZERLAND

075 - SAMSUNG (726 78 64) http://www.samsung.com/se

0848 - SAMSUNG (7267864,

CHF 0.08/min) http://www.samsung.com/ch

U.K

0845 SAMSUNG (7267864) http://www.samsung.com/uk

ESTONIA

LATVIA

LITHUANIA

KAZAKHSTAN

KYRGYZSTAN

RUSSIA

TADJIKISTAN

UKRAINE

UZBEKISTAN

CIS

800-7267

8000-7267

8-800-77777

8-10-800-500-55-500

00-800-500-55-500

8-800-555-55-55

8-10-800-500-55-500

8-800-502-0000

8-10-800-500-55-500 http://www.samsung.com/ee http://www.samsung.com/lv http://www.samsung.com/lt http://www.samsung.com/ kz_ru http://www.samsung.ru

http://www.samsung.ua

http://www.samsung.com/ kz_ru

Appendix

AUSTRALIA

CHINA

INDIA

1300 362 603

Asia Pacific

800-810-5858

400-810-5858 http://www.samsung.com/au http://www.samsung.com/cn

010-6475 1880

HONG KONG:3698 - 4698 http://www.samsung.com/hk

3030 8282 http://www.samsung.com/in

1-800-3000-8282

INDONESIA

JAPAN

MALAYSIA

1800 110011

0800-112-8888

0120-327-527

1800-88-9999

NEW ZEALAND 0800 SAMSUNG(0800 726

786)

PHILIPPINES 1-800-10-SAMSUNG

(726-7864) http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/nz http://www.samsung.com/ph

SINGAPORE

THAILAND

TAIWAN

VIETNAM

1-800-3-SAMSUNG

(726-7864)

02-5805777

1800-SAMSUNG(726-7864) http://www.samsung.com/sg

1800-29-3232, 02-689-3232 http://www.samsung.com/th

0800-329-999 http://www.samsung.com/tw

1 800 588 889 http://www.samsung.com/vn

Middle East & Africa

SOUTH AFRICA 0860-SAMSUNG(726-7864) http://www.samsung.com/za

TURKEY

U.A.E

444 77 11

800-SAMSUNG(726-7864) http://www.samsung.com/tr http://www.samsung.com/ae

8000-4726

Terms

Dot Pitch

Vertical Frequency

Horizontal Frequency

The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot

Pitch'. Unit: mm

The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical

Frequency or Refresh Rate. Unit: Hz

Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal

Appendix

Interlace and Non-Interlace

Methods

Plug & Play

Resolution

SRS TS XT

Multiple Display Control

(MDC)

Cycle. The inverse number of the Horizontal Cycle is called

Horizontal Frequency. Unit: kHz

Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.

This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function.

The number of horizontal and vertical dots used to compose the screen image is called the 'resolution'. This number shows the accuracy of the display. A high resolution is good for performing multiple tasks as more image information can be shown on the screen.

Example: If the resolution is 1360(1920) x 768(1080), this means the screen is composed of 1360(1920) horizontal dots (horizontal resolution) and 768(1080) vertical lines

(vertical resolution).

This feature outputs sonorous and vivid 3D sound as for 5.1

channel speaker sound but through a 2-channel speaker. It has a good effect when stereo signals are input.

A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for communicating between a PC and a display.

Correct Disposal

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase con-

Appendix

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) tract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product - Europe only

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.

Note

The rechargeable battery incorporated in this product is not user replaceable. For information on its replacement, please contact your service provider.

Authority

Information in this document is subject to change without notice.

© 2009 Samsung Electronics Co., Ltd. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR ® name and logo are registered trademarks of the U.S. Environmental Protection Agency

(EPA).As an ENERGY STAR ® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR owners.

® guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective

Appendix

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • 160 cm (63") Plasma
  • Full HD 1920 x 1080 pixels 16:9
  • 1000 cd/m² 8 ms

Related manuals

Download PDF

advertisement

Table of contents