Samsung C24A650X User manual

Add to my manuals
114 Pages

advertisement

Samsung C24A650X User manual | Manualzz
User Manual
SyncMaster
C24A650X
C27A650X
C24A650U
C27A650U
The color and the appearance may differ depending on
the product, and the specifications are subject to
change without prior notice to improve the performance.
BN46-00083B-01
Before Using the Product
Copyright
The contents of this manual are subject to change without notice to improve quality.
© 2011 Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is
prohibited.
The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics.
Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation.
VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
z
An administration fee may be charged if either
†
(a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual).
†
(b) you bring the unit to a repair centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
z
The amount of such administration charge will be advised to you before any work or home visit is
carried out.
Icons used in this manual
The following images are for reference only. Real-life situations may
differ from what is shown in the images.
Symbols for safety precautions
A serious or fatal injury may result if instructions are not followed.
Warning
Caution
Personal injury or damage to properties may result if instructions are
not followed.
Before Using the Product
2
Before Using the Product
Activities marked by this symbol are prohibited.
Instructions marked by this symbol must be followed.
Before Using the Product
3
Before Using the Product
Cleaning
Cleaning
Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
Take the following steps when cleaning.
1. Power off the monitor and computer.
2. Disconnect the power cord from the monitor.
Hold the power cable by the plug and do not touch the cable with wet
hands. Otherwise, an electric shock may result.
3. Wipe the monitor with a clean, soft and dry cloth.
z
Do not apply a cleaning agent that contains alcohol,
solvent, or surfactant to the monitor.
!
z
Do not spray water or detergent directly on the product.
4. Wet a soft and dry cloth in water and wring thoroughly to clean the
exterior of the monitor.
5. Connect the power cord to the product after cleaning the product.
6. Power on the monitor and computer.
!
Before Using the Product
4
Before Using the Product
Securing the Installation Space
z
Ensure some space around the product for ventilation. A rise in the internal temperature may cause
a fire and damage the product. Be sure to allow the amount of space as shown below or greater
when installing the product.
The exterior may differ depending on the product.
10 cm
10 cm
10 cm
10 cm
10 cm
Precautions for storage
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used
nearby.
Be sure to contact Samsung Customer Service Center (108page) if the inside of the monitor needs
cleaning. (service fee will be charged).
Safety Precautions
Electricity and Safety
The following images are for reference only. Real-life situations may differ from what is shown in the
images.
Before Using the Product
5
Before Using the Product
Warning
Do not use a damaged power cord or plug, or a loose power socket.
z
An electric shock or fire may result.
Do not plug many products into the same power socket.
z
Otherwise, the socket may overheat and cause a fire.
Do not touch the power plug with wet hands.
z
Otherwise, an electric shock may result.
Insert the power plug all the way in so it is not loose.
z
An unstable connection may cause a fire.
!
Connect the power plug to a grounded power socket (type 1 insulated devices
only).
!
z
An electric shock or injury may result.
Do not bend or pull the power cord with force. Do not weigh the power cord
down with a heavy object.
z
A damaged power cord may cause an electric shock or fire.
Do not place the power cord or product near heat sources.
z
An electric shock or fire may result.
Remove foreign substances such as dust around the plug pins and power socket
with a dry cloth.
!
z
Otherwise, a fire may result.
Before Using the Product
6
Before Using the Product
Caution
Do not unplug the power cord when the product is in use.
z
The product may become damaged by an electric shock.
Do not use the power cord for products other than authorized products supplied
by Samsung.
z
!
An electric shock or fire may result.
Keep the power socket where the power cord is connected unobstructed.
z
If any problem occurs in the product, unplug the power cable to completely
cut the power to the product.
!
Power to the product cannot be completely cut off with the power button.
Hold the plug when disconnecting the power cord from the power socket.
z
An electric shock or fire may result.
!
Installation
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP
OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
z
Otherwise, a fire may result.
Avoid installing the product in a narrow space with bad ventilation, such as a
bookshelf or wall closet.
z
Otherwise, a fire may result due to an increased internal temperature.
Keep the plastic packaging bag for the product in a place that cannot be reached
by children.
!
z
Children may suffocate.
Before Using the Product
7
Before Using the Product
Do not install the product on an unstable or vibrating surface (insecure shelf,
sloped surface, etc.).
z
The product may fall and break or cause a personal injury.
z
Using the product in an area with excess vibration may damage the product
or cause a fire.
Do not install the product in a vehicle or a place exposed to dust, moisture (water
drips, etc.), oil, or smoke.
z
!
An electric shock or fire may result.
Do not expose the product to direct sunlight, heat, or a hot object such as a
stove.
z
Otherwise, the product lifespan may be reduced, or a fire may result.
Do not install the product within the reach of young children.
z
The product may fall and injure children.
Caution
Take care not to drop the product when moving it.
z
Otherwise, product failure or personal injury may result.
!
Do not set down the product on its front.
z
The screen may become damaged.
When installing the product on a cabinet or shelf, make sure that the bottom
edge of the front of the product is not protruding.
z
The product may fall and break or cause a personal injury.
z
Install the product only on cabinets or shelves of the right size.
Before Using the Product
8
Before Using the Product
Put down the product carefully.
z
The product may fall and break or cause a personal injury.
!
SAMSUNG
!
Installing the product in an unusual place (a place exposed to a lot of fine
particles, chemical substances or extreme temperatures, or an airport or train
station where the product should operate continuously for an extended period of
time) may seriously affect its performance.
z
Be sure to consult Samsung Customer Service Center (108page) before
installation if you want to install the product at such a place.
Operation
Warning
High voltage runs through the product. Do not attempt to disassemble, repair, or
modify the product on your own.
z
An electric shock or fire may result.
z
Contact Samsung Customer Service Center (108page) for repair.
Before you move the product, be sure to turn off the power switch and remove all
the cables connected to the product, including the power cord and the antenna
cable.
!
z
Otherwise, the power cord may be damaged and a fire or electric shock may
result.
If the product generates a strange noise, a burning smell, or smoke, remove the
power cord immediately and contact Samsung Customer Service Center
(108page).
!
z
An electric shock or fire may result.
Do not let children hang from the product or climb on top of it.
z
The product may fall, and your child may become injured or seriously
harmed.
If the product falls or the exterior is damaged, power off the product, remove the
power cord, and contact Samsung Customer Service Center (108page).
z
Otherwise, an electric shock or fire may result.
Before Using the Product
9
Before Using the Product
Do not put a heavy object, toy, or sweets on top of the product.
z
The product or heavy objects may fall as children try to reach for the toy or
sweets resulting in a serious injury.
During a lightning or thunderstorm, remove the power cord and do not touch the
antenna cable.
z
!
An electric shock or fire may result.
Do not drop objects on the product or apply impact.
z
An electric shock or fire may result.
!
Do not move the product by pulling the power cord or any cable.
z
Otherwise, the power cable may be damaged and product failure, an electric
shock or fire may result.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate
the area immediately.
!
GAS
z
Sparks can cause an explosion or fire.
z
During a lightning or thunderstorm, do not touch the power cord or antenna
cable.
Do not lift or move the product by the power cord or any cable.
z
Otherwise, the power cable may be damaged and product failure, an electric
shock or fire may result.
Do not use or keep combustible spray or an inflammable substance near the
product.
!
z
An explosion or fire may result.
Ensure the vents are not blocked by tablecloths or curtains.
z
Otherwise, a fire may result from an increased internal temperature.
Before Using the Product
10
Before Using the Product
100
Do not insert a metallic object (a chopstick, coin, hair pin, etc.) or inflammable
object (paper, match, etc.) into the vent or ports of the product.
z
If water or any foreign substance enters the product, be sure to power off the
product, remove the power cord, and contact Samsung Customer Service
Center (108page).
z
Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic
objects on top of the product.
z
If water or any foreign substance enters the product, be sure to power off the
product, remove the power cord, and contact Samsung Customer Service
Center (108page).
z
Product failure, an electric shock or fire may result.
Caution
Leaving the screen fixed on a stationary image for an extended period of time
may cause afterimage burn-in or defective pixels.
z
!
If you are not going to use the product for an extended period of time,
activate power-saving mode or a moving-picture screen saver.
-_!
Disconnect the power cord from the power socket if you do not plan on using the
product for an extended period of time (vacation, etc).
z
Otherwise, a fire may result from accumulated dust, overheating, an electric
shock, or electric leakage.
Use the product at the recommended resolution and frequency.
z
Your eyesight may deteriorate.
!
Do not put DC power adapters together.
z
Otherwise, a fire may result.
Remove the plastic bag from the DC power adapter before you use it.
z
Otherwise, a fire may result.
Before Using the Product
11
Before Using the Product
Do not let water enter the DC power device or get the device wet.
z
An electric shock or fire may result.
z
Avoid using the product outdoors where it can be exposed to rain or snow.
z
Be careful not to get the DC power adapter wet when you wash the floor.
Do not put the DC power adapter near to any heating apparatus.
z
Otherwise, a fire may result.
Keep the DC power adapter in a well-ventilated area.
!
Looking at the screen too close for an extended period of time can deteriorate
your eyesight.
!
Do not hold the monitor upside-down or move it by holding the stand.
z
The product may fall and break or cause a personal injury.
Do not use humidifiers or stoves around the product.
z
An electric shock or fire may result.
Rest your eyes for more than 5 minutes for every 1 hour of product use.
z
Eye fatigue will be relieved.
!
Do not touch the screen when the product has been turned on for an extended
period of time as it will become hot.
Store the small accessories used with the product out of reach of children.
!
Before Using the Product
12
Before Using the Product
Exercise caution when adjusting the product angle or stand height.
!
z
Otherwise, children's fingers or hands may become stuck and injured.
z
Tilting the product excessively may cause it to fall and result in personal
injury.
Do not place heavy objects on the product.
z
Product failure or personal injure may result.
Correct posture to use the product
Use the product in the correct posture as follows:
z
Straighten your back.
z
Allow a distance of 45 to 50cm between your eye and the screen, and look slightly
downward at the screen.
Keep your eyes directly in front of the screen.
z
Adjust the angle so light does not reflect on the screen.
z
Keep your forearms perpendicular to your upper arms and level with the back of
your hands.
z
Keep your elbows at about a right angle.
z
Adjust the height of the product so you can keep your knees bent at 90 degrees or
more, your heels attached to the floor, and your arms lower than your heart.
Before Using the Product
13
Table Of Contents
BEFORE USING THE
PRODUCT
PREPARATIONS
USING "HUB MONITOR"
2
Copyright
2
2
Icons used in this manual
Symbols for safety precautions
4
Cleaning
4
5
5
Cleaning
Securing the Installation Space
Precautions for storage
5
Safety Precautions
5
7
9
Electricity and Safety
Installation
Operation
13
Correct posture to use the product
19
Checking the Contents
19
20
Removing the Packaging
Checking the Components
22
Parts
22
24
Frontal Buttons
Reverse Side
26
Installation
26
27
27
28
29
30
Attaching the Stand
Adjusting the Product Tilt and Height
Rotating the Monitor
Attaching and detaching the wirelessconnection dongle (Rx)
Installing a Wall-mount Kit or Desktop Stand
Anti-theft Lock
31
"MagicRotation Auto"
32
About "HUB Monitor"
33
Software Installation for Using "HUB
Monitor"
33
Installing "Samsung HUB Monitor Setup"
Table Of Contents
14
Table Of Contents
CONNECTING AND USING
A SOURCE DEVICE
SCREEN SETUP
35
Connecting the Product to a PC to Use
"HUB Monitor"
35
39
Connecting to a PC via Wireless USB
Connecting to a PC via the USB Cable
40
Utilizing "HUB Monitor"
40
42
Using the Product as a USB HUB
Connecting to a LAN
43
Configuring the HUB Monitor IP
43
44
Dynamic IP
Static IP
47
Notice before your use of Wireless USB
or USB Mode
48
Before Connecting
48
Pre-connection Checkpoints
49
Connecting and Using a PC
49
51
52
53
Connecting to a PC
Driver Installation
Setting Optimum Resolution
Changing the Resolution Using a PC
56
Connecting Headphones
57
Connecting the Power
58
MAGIC
58
60
SAMSUNG MAGIC Bright
SAMSUNG MAGIC Color
61
Brightness
61
Configuring Brightness
62
Contrast
62
Configuring Contrast
63
Sharpness
63
Configuring Sharpness
Table Of Contents
15
Table Of Contents
CONFIGURING TINT
RESIZING OR
RELOCATING THE
SCREEN
64
Coarse
64
Adjusting Coarse
65
Fine
65
Adjusting Fine
66
Response Time
66
Configuring Response Time
67
Red
67
Configuring Red
68
Green
68
Configuring Green
69
Blue
69
Configuring Blue
70
Color Tone
70
Configuring the Color Tone Settings
71
Gamma
71
Configuring Gamma
72
Image Size
72
Changing the Picture Size
73
H-Position & V-Position
73
Configuring H-Position & V-Position
74
Menu H-Position & Menu V-Position
74
Configuring Menu H-Position & Menu VPosition
Table Of Contents
16
Table Of Contents
SETUP AND RESET
75
HUB
75
76
77
78
79
80
80
Auto Wireless Detection
Wireless Connection
USB Connection
Analog
HDMI
USB Super Charging
Wireless ID
81
ECO
81
83
86
87
Eco Motion Sensor
Eco Light Sensor
Eco Saving
Eco Icon Display
89
Menu Transparency
89
Changing Menu Transparency
90
Language
90
Changing the Language
91
PC/AV Mode
91
Configuring PC/AV Mode
92
Auto Source
92
Configuring Auto Source
93
Display Time
93
Configuring Display Time
94
Key Repeat Time
94
Configuring Key Repeat Time
95
Customized Key
95
Configuring Customized Key
96
Off Timer On/Off
96
Configuring Off Timer On/Off
97
Off Timer Setting
97
Configuring Off Timer Setting
Table Of Contents
17
Table Of Contents
INFORMATION MENU AND
OTHERS
TROUBLESHOOTING
GUIDE
SPECIFICATIONS
APPENDIX
98
Reset
98
Initializing Settings (Reset)
99
INFORMATION
99
Displaying INFORMATION
99
Configuring Brightness in the Startup
Screen
100
Requirements Before Contacting
Samsung Customer Service Center
100
100
101
Testing the Product
Checking the Resolution and Frequency
Check the followings.
103
Q&A
104
General
106
PowerSaver
107
Standard Signal Mode Table
108
Contact SAMSUNG WORLDWIDE
110
Correct Disposal of This Product (Waste
Electrical & Electronic Equipment)
111
Terminology
INDEX
Table Of Contents
18
1
1.1
Preparations
Checking the Contents
1.1.1 Removing the Packaging
1
Open the packaging box. Be careful not to damage the product when you open the packaging with
a sharp instrument.
2
Remove the Styrofoam from the product.
3
Check the components and remove the Styrofoam and plastic bag.
4
z
The appearance of actual components may differ from the image shown.
z
This image is for reference only.
Store the box in a dry area so that it can be used when moving the product in the future.
1 Preparations
19
1
Preparations
1.1.2 Checking the Components
z
Contact the dealer from whom you purchased the product if any item is missing.
z
The appearance of the components and items sold separately may differ from the image shown.
Components
Quick setup guide
Warranty card
(Not available in all locations)
User manual
Wireless Connection
Dongle(Tx)
Wireless Connection
Dongle(Rx)
Stand base
(Sold separately for C24A650U (Sold separately for C24A650U
and C27A650U models)
and C27A650U models)
Power cable
DC power adapter
USB 3.0 cable
D-SUB cable
HDMI cable (optionally)
USB gender changer
(Sold separately for C24A650U
and C27A650U models)
Components may differ in different locations.
1 Preparations
20
1
Preparations
USB gender changer (Sold separately for C24A650U and C27A650U models)
When the wireless-connection dongle cannot connect to your notebook PC, connect it using the USB
gender changer.
Items sold separately
The following items can be purchased at your nearest retailer.
LAN cable
HDMI-DVI cable
1 Preparations
21
1
1.2
Preparations
Parts
1.2.1 Frontal Buttons
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
Icons
Description
z
Open or close the onscreen display (OSD) menu, or return to the last
menu.
z
OSD control lock: Maintain the current settings, or lock the OSD
control to prevent unintended changes to settings.
To lock the OSD control, press the MENU button [ MENU ] for five
seconds.
MENU
To unlock the locked OSD control, press the MENU button [ MENU]
for more than five seconds.
If the OSD control is locked,
z
Brightness and Contrast can be adjusted, and INFORMATION
can be viewed.
z
The function that was configured as Customized Key before
locking the OSD control can be used by pressing the [ HUB ]
button.
1 Preparations
22
1
Preparations
Icons
Description
Configure Customized Key and press [ HUB ]. The following options will be
enabled.
HUB
HUB - ECO - MAGIC - Image Size
To configure Customized Key, go to SETUP&RESET
→
Customized Key and select the mode you want.
Move to the upper or lower menu or adjust the value for an option on the
OSD menu.
Adjust the screen brightness.
Volume (VOL) can be adjusted if a cable is connected to the [HDMI IN]
port.
Confirm a menu selection.
Pressing the [
] button when the OSD menu is not displayed will
change the input source (Wireless USB/USB/Analog/HDMI). If you power
on the product or change the input source by pressing the [
]
button, a message that shows the changed input source will appear at
the top left corner of the screen.
Press the [AUTO] button to automatically adjust the screen settings.
AUTO
z
Available only in Analog mode.
z
Changing the resolution in Display Properties will activate the
Auto Adjustment function.
Turn the screen on or off.
The power indicator will be lit when the product is operating normally.
(Power Indicator)
z
Refer to "10.2 PowerSaver" for details about the power-saving
function.
z
To reduce power consumption, it is best to remove the power
cable when you will not be using the product for an extended
period of time.
z
The power LED will turn red if a wireless communication
connection is established.
1 Preparations
23
1
Preparations
1.2.2 Reverse Side
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
DC 14V
HDMI IN
RGB IN
LAN
WIRELESS LAN ADAPTER
Port
Description
Connects to the DC power adapter.
Connects to a source device using an HDMI cable.
Connects to a PC using the D-SUB cable.
Connects to a network using the LAN cable.
Connects to an audio output device such as headphones.
Connects to a source device via a USB cable. Compatible with a
USB cable version 2.0 or lower.
Connects to a source device via a USB cable. Compatible with a
USB cable version 3.0 or lower.
1 Preparations
24
1
Preparations
Port
Description
Connects to a PC via a USB cable.
This port can only connect to a PC.
Connect to the wireless-connection dongle (Rx).
1 Preparations
25
1
1.3
Preparations
Installation
1.3.1 Attaching the Stand
Place a protective cloth or
cushion on a flat surface. Next,
place the product with the face
down on top of the cloth or
cushion.
Insert the stand base into the
stand in the direction of the
arrow.
Do not remove the fixing pin until
you are finished attaching the
stand.
Tightly fasten the screw to the
bottom of the base.
After installing the stand, place
the product upright.
You can remove the fixing pin
and adjust the stand now.
- Caution
Do not hold the product upside
down only by the stand.
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
1 Preparations
26
1
Preparations
1.3.2 Adjusting the Product Tilt and Height
The color and shape of parts may differ from what is shown. Specifications are subject to change
without notice to improve quality.
z
To adjust the height, remove the fixing pin.
z
The monitor tilt and height can be adjusted.
z
Hold the top center of the product and adjust the height carefully.
1.3.3 Rotating the Monitor
You can rotate your monitor as shown below.
z
Be sure to fully extend the stand before rotating the monitor.
z
If you rotate the monitor without fully extending the stand, the corner of the monitor may hit the
floor and get damaged.
z
Do not rotate the monitor counterclockwise. The monitor may get damaged.
1 Preparations
27
1
Preparations
1.3.4 Attaching and detaching the wireless-connection dongle (Rx)
Attaching the wireless-connection dongle (Rx)
Detaching the wireless-connection dongle (Rx)
1 Preparations
28
1
Preparations
1.3.5 Installing a Wall-mount Kit or Desktop Stand
Before Installation
Power the product off and remove the power cable from the power socket.
Place a protective cloth or
cushion on a flat surface. Next,
place the product with the face
down on top of the cloth or
cushion.
Unfasten the screw from the
back of the product.
Lift and detach the stand.
Installing a Wall-mount Kit or Desktop Stand
2
1
A
3
4
B
A Attach the wall-mount kit or desktop stand here
B Bracket (sold separately)
Align the grooves and tightly fasten the screws on the bracket on the product with the corresponding
parts on the wall-mount kit or desktop stand you want to attach.
1 Preparations
29
1
Preparations
Notes
z
Using a screw longer than the standard length can damage the internal components of the
product.
z
The length of screws required for a wall mount that does not comply with the VESA standards may
vary depending on the specifications.
z
Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit
or desktop stand using excessive force. The product may get damaged or fall and cause personal
injury. Samsung shall not be held liable for any damage or injury caused by using improper screws
or attaching the wall-mount kit or desktop stand using excessive force.
z
Samsung shall not be held liable for any product damage or personal injury caused by using a wallmount kit other than the one specified or from an attempt to install the wall-mount kit on your own.
z
To mount the product on a wall, ensure you purchase a wall-mount kit that can be installed 10cm
or farther away from the wall.
z
Be sure to use a wall-mount kit that complies with the standards.
1.3.6 Anti-theft Lock
An anti-theft lock allows you to use the product securely even in public places. The locking device shape
and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft
locking device for details. The lock device is sold separately.
To lock an anti-theft locking device:
1
Fix the cable of your anti-theft locking device to a heavy object
such as a desk.
2
3
Put one end of the cable through the loop on the other end.
Insert the locking device into the anti-theft lock slot at the back of
the product.
4
Lock the locking device.
z
An anti-theft locking device can be purchased separately.
z
Refer to the user guide provided with your anti-theft locking device for details.
z
Anti-theft locking devices can be purchased at electronics retailers or online.
1 Preparations
30
1
1.4
Preparations
"MagicRotation Auto"
The "MagicRotation Auto" function detects the rotation of monitors that are fitted with a rotation sensor
and rotates the Windows screen accordingly.
[Software Installation]
1
2
Insert the user manual CD provided with the product into the CD-ROM drive.
Follow the instructions given on the screen to proceed with installation.
After installation, the on-screen display (OSD) menu will be displayed in the language of the operating
system.
(This complies with the basic policies of Windows.)
[Caution]
1
2
Compatible only with Windows 7 (32 bits or 64 bits)
Compatible with a graphics card that complies with the DDC/CI and MS API standards
With a graphics card that does not comply with the aforementioned standards, the "MagicRotation
Auto" function may not be available.
3
4
To maximize the performance of the function, update the graphics card driver to the latest version.
Fourteen languages are available as installation languages.
(QJOLVK)UDQoDLV'HXWVFK0DJ\DU,WDOLDQR3ROVNL3RUWXJXrV
ƧNJLjLjǁƿǀ(VSDxRO6YHQVND7UNoHᣣᧄ⺆㩷∝䇁ଞ˲߭
5
If the orientation is set to a mode other than "Landscape" in the screen resolution menu on Windows
7, the "MagicRotation Auto" function may not work properly.
6
The OSD menu will be displayed if the monitor is rotated. When the monitor is rotated, the screen
reconfiguration process may be displayed or screen burn-in may appear, depending on the graphics
card. This is performed by the Windows operating system and has nothing to do with the product.
7
If you do not want the screen to rotate automatically when the monitor is rotated, press the Windows
and L keys at the same time to lock the Windows operating system. If the operating system cannot
be locked, it is due to the constraints of Windows API and has nothing to do with the product.
8
This function is not available when the input source is Wireless USB or USB.
1 Preparations
31
2
Using "HUB Monitor"
You can use the "HUB Monitor" function by connecting the product to a PC through the
Wireless USB function or a USB cable. "HUB Monitor" allows the product to function as a HUB
so that you can control a connected device from the product without having to connect to a
PC.
2.1
About "HUB Monitor"
"HUB Monitor" is a HUB system developed independently by Samsung and allows you to conveniently
control a notebook PC that has a small screen and a limited number of input/output ports available.
Notebook or netbook computers offer portability but may prove inconvenient when used at the office or
at home. Connecting a notebook PC to this product, which has the "HUB Monitor" function, allows you
to view the small notebook PC screen on a larger screen. With the HUB function, you can control multiple
devices at the same time from the notebook PC, even if the notebook PC has a limited number of input/
output ports.
In particular, the high-tech Wireless USB feature allows you to connect a notebook PC to the product
wirelessly and, from the product, enjoy various multimedia contents stored on the notebook PC.
You can also use triple monitors by configuring the display settings.
2 Using "HUB Monitor"
32
2
2.2
Using "HUB Monitor"
Software Installation for Using "HUB Monitor"
Install on your PC the software provided with the product.
To maximize the performance of your HUB Monitor, visit www.samsung.com and upgrade the driver
periodically.
2.2.1 Installing "Samsung HUB Monitor Setup"
This software is needed to use the HUB Monitor function. Software installation may be affected by the
graphics card, motherboard, or network conditions of the PC.
1
2
3
4
Insert the installation CD into the CD-ROM drive.
Click the "Installing the Software" button.
Click the "Samsung HUB Monitor Setup" installation program.
Check the model name indicated on the label at the bottom right on the back of the product. Next,
install the corresponding program for the model, referring to the following instructions.
For model CA650X, click the [
z
] icon to install the corresponding program.
This applies if you want to connect the product to the PC wirelessly using a wireless-connection
dongle. (The product can also be connected to the PC through a wired connection using a USB
3.0 cable.)
†
Select the country where you will use the product when installing the driver initially. Using
the product in a country other than the selected country would be contrary to the law.
†
If a software installation window does not appear in the main screen, install "Samsung
HUB Monitor Setup" using the execution file ("CA650X_Wireless_HUB_Monitor.exe") on
the CD-ROM.
For model CA650U, click the [
z
] icon to install the corresponding program.
This applies if you want to connect the product to the PC through a wired connection using a
USB 3.0 cable.
5
†
To connect the product to the PC using a wireless-connection dongle (sold separately),
install the program for CA650X [
]. The CA650U model does not come with a
wireless-connection dongle. The dongle can be purchased at your nearest retailer.
†
If a software installation window does not appear in the main screen, install "Samsung
HUB Monitor Setup" using the execution file ("CA650U_USB_HUB_Monitor.exe") on the
CD-ROM.
Follow the instructions given on the screen to proceed with installation.
2 Using "HUB Monitor"
33
2
Using "HUB Monitor"
6
After installing "Samsung HUB Monitor Setup", customize the audio output port settings as required.
Control Panel
→ Sound → Speakers → Configure Speakers
1
2
3
4
"Samsung HUB Monitor Setup" software consists of "Samsung Wireless HUB Monitor" and
"Samsung Wireless Monitor". To delete the software, go to Start
→
Settings
→
Control Panel
and double-click Add or Remove Programs on the PC. Select "Samsung Wireless HUB Monitor"
and "Samsung Wireless Monitor" from the list and click Change/Remove. (Applicable only when
the [
] program is installed using the execution file ("CA650X_Wireless_HUB_Monitor.exe").)
2 Using "HUB Monitor"
34
2
2.3
Using "HUB Monitor"
Connecting the Product to a PC to Use "HUB Monitor"
Connect the product to a PC via Wireless USB and the USB cable.
Connecting the product and PC via Wireless USB and the USB cable will allow you to hear audio when
you plug headphones or speakers into [
] on the product. (Not available when the D-SUB or HDMI-DVI
cable is connected.)
If a PC is connected, the product will automatically switch to the mode of the detected input source. If
several source devices are connected to the product, the input source will automatically change
according to this priority, from left to right: Wireless USB mode > USB mode > Analog mode > HDMI
mode.
When the product connects to a PC for the first time, the optimum resolution (1920 x 1080) will be
selected automatically and the display will be set to extended mode. For subsequent connections of the
product to the PC, customized resolution settings will be applied.
When multiple display output ports on the PC are connected to the HUB Monitor, different signals may
output depending on the system specifications of the PC.
2.3.1 Connecting to a PC via Wireless USB
z
The CA650U model does not come with a wireless-connection dongle. The dongle can be
purchased at your nearest retailer.
z
The power LED will turn red if a wireless communication connection is established.
CSM
WIRELESS USB
WIRELESS LAN ADAPTER
To use the Wireless USB function, connect the wireless-connection dongle (Rx) provided with the
product to the [WIRELESS LAN ADAPTER] port on the product. Next, connect the wireless-connection
dongle (Tx) to the USB port on the PC. The wireless-connection dongle allows a wireless connection
2 Using "HUB Monitor"
35
2
Using "HUB Monitor"
between the product and a PC. The dongle connected to a PC should point at the product to maximize
signal reception.
Wireless communication can be affected by the surrounding environmental conditions. Do not place an
object, or obstacle, between the monitor and PC. The object can affect the sensitivity of the signal
transmission/reception.
z
Ensure the receiver (dongle) on the HUB Monitor is at the same level and facing the transmitter
(dongle) on the PC.
The table is a potential obstacle and can degrade wireless performance if the receiver (dongle) on
the HUB Monitor is not placed at the same level as the transmitter (dongle) on the PC. This issue
may occur even if the dongles face each other.
z
The sensitivity of the signal reception/transmission can affect the performance of video or game
playback (choppy or slowed-down video).
z
To maximize the transmission/reception, attach the transmitter (dongle) to the USB port (on either
side of the notebook PC) that is closest to the receiver (dongle) on the HUB Monitor.
z
To maximize the wireless communication performance, ensure your PC is within a range of 70cm
from the receiver (dongle) on the HUB Monitor. Ensure the PC and monitor are placed on the same
table or at the same height. Otherwise, the signal transmission/reception can be degraded.
z
Using the HUB Monitor on a steel table will degrade wireless performance.
z
Do not place any object that can obstruct the signal transmission in front of the product. Such
objects may decrease signal reception.
z
This product cannot connect to multiple PCs wirelessly at the same time and vice versa.
Connecting to a PC via Wireless USB
1
2
Install "Samsung HUB Monitor Setup" on the PC, and attach the dongle to the USB port on the PC.
Press [
] to change the input source for the product to Wireless.
2 Using "HUB Monitor"
36
2
Using "HUB Monitor"
3
Double-click the "Wireless Display Manager" icon created on the desktop. The following screen will
appear.
Five levels of signal intensity are available.
All the five signal intensity indicator bars, including the green bar, will be lit when the strongest signal
is received. The weakest signal intensity will turn on the red bar only.
The following "Found New Hardware Wizard" screen may appear when the product attempts to
connect to a PC via Wireless USB. Proceed with installation following the instructions displayed.
4
Double-click the HUB Monitor to open the following screen.
If a connection is established between the product and PC, [
] will appear over the signal intensity
bars as shown below and the product will display the PC screen. If [
] does not appear, the
connection is not established between the product and PC.
2 Using "HUB Monitor"
37
2
Using "HUB Monitor"
5
Right-click on Connected Monitor to display the context menu as shown below.
z
Disconnect: Disconnect Wireless between the product and PC.
z
Set as default: Give first priority to the product to connect to the PC once a Wireless signal is
detected. A star will appear beside the monitor icon if the product is set as the default monitor.
z
Rename: Customize the name of the connected monitor.
The program will automatically activate to allow you to use the Wireless USB connection even
when the "Wireless Display" window is closed.
Automatic/manual Wireless USB connection
Set Auto Wireless Detection to On under HUB in the on-screen display menu. A Wireless USB
connection will automatically be established if the product is within 70cm from the PC. The first priority
will be given to a Wireless USB connection even when the product is in power-saving mode or is
connected to another input source (Analog/HDMI/USB). The Connecting to PC… message will be
displayed while connection is attempted.
To establish a Wireless USB connection when Auto Wireless Detection is set to Off, press [
] to
switch to Wireless USB mode. The Connecting to PC… message will be displayed while connection is
attempted. Deactivating the Wireless USB mode will automatically restore the previous mode.
2 Using "HUB Monitor"
38
2
Using "HUB Monitor"
2.3.2 Connecting to a PC via the USB Cable
Connect the USB cable to [
] on the back of the product and USB [
] on the PC.
A USB 2.0 cable can be used to connect the product to a PC. However, the PC should support USB
3.0 for the USB 3.0 function to work fully.
Connecting to a PC using the USB cable
1
2
3
Connect a desktop PC to the product using the USB cable.
Press [
] to change the input source for the product to USB mode.
The product will display the PC screen if the connection is established.
Automatic/manual USB cable connection
The input source will automatically change to USB mode if a USB cable connects to the product and a
PC. The USB mode will be given top priority even when the product is in power-saving mode or is
connected to another source (Analog/HDMI). If the input source does not switch to USB mode
automatically, press [
] to switch to USB mode.
z
Top priority will be given to Wireless USB mode if the product is connected to Wireless USB and a
USB cable at the same time.
z
Disconnecting the USB cable will automatically restore the previous mode.
2 Using "HUB Monitor"
39
2
2.4
Using "HUB Monitor"
Utilizing "HUB Monitor"
HUB Monitor is only available when the product is connected to a PC via Wireless USB or a USB cable.
2.4.1 Using the Product as a USB HUB
Using the product as a hub, connect and use various source devices with the product at the same time.
A PC cannot connect to multiple source devices at the same time as it has a limited number of input/
output ports available. The HUB feature on the product will improve your work efficiency by allowing you
to connect multiple source devices to the USB ports on the product at the same time without connecting
them to a PC.
z
The product is compatible with a USB 2.0 cable. However, your PC should support USB 3.0 for
the HUB function to work fully.
z
If you experience a communication problem with a PC that provides the USB 3.0 function,
download and install the latest driver version from the PC manufacturer.
Using the Product as a USB HUB
WIRELESS LAN ADAPTER
If multiple source devices are connected to the PC, the many cables around the PC may look messy.
Connecting the devices directly to the product will resolve such inconvenience.
z
To detect and start a source device faster, connect the device to the blue USB 3.0 port on the
back of the product.
z
An external mass-storage HDD requires external power supply. Be sure to connect it to a power
source.
2 Using "HUB Monitor"
40
2
Using "HUB Monitor"
WIRELESS LAN ADAPTER
Connect a mobile IT device such as an MP3 player or smart phone to the product when connected to a
PC. This allows you to use the device from the PC or charge the battery on the device.
z
To charge the battery of a device, be sure to connect the device to the blue USB 3.0 port on the
back of the product.
z
Battery charging is available in power-saving mode, but not available when the product is powered
off.
z
Note that the battery will not be charged if the power cable is disconnected from the power socket.
WIRELESS LAN ADAPTER
Connect multiple source devices to the product and use the device you want by changing the input
source.
2 Using "HUB Monitor"
41
2
Using "HUB Monitor"
2.4.2 Connecting to a LAN
"HUB Monitor" allows you to use the Internet from a PC when you connect a LAN cable to the product (if
the product is connected to the PC), without having to connect the LAN cable directly to the PC.
This is achieved by an internal chip that transmits data received via the LAN cable to the PC as a
converted USB signal.
Connecting to a LAN via Wireless USB
LAN
WIRELESS LAN ADAPTER
Connecting to a LAN via USB cable
LAN
This product cannot connect to multiple source PCs at the same time and vice versa.
2 Using "HUB Monitor"
42
2
2.5
Using "HUB Monitor"
Configuring the HUB Monitor IP
1
After installing the integrated driver for HUB Monitor, go to Control Panel
→ Network and Internet
→ Network and Sharing Center → Change adapter settings.
2
You can see that the following two devices are displayed.
a.
The user PC’s network device
b.
The HUB Monitor’s network device (USB to Ethernet adapter)
The two devices above refer to your PC’s LAN network device and your HUB Monitor’s network
device.
To use the Internet using the HUB Monitor’s LAN network, configure the network settings as follows
according to the type of IP you will be using.
2.5.1 Dynamic IP
The dynamic IP address mode automatically configures the network settings on the PC using data sent
by a server, which allots an IP address. This is possible, owing to the “DHCP (Dynamic Host
Configuration Protocol)” service. The service consists of three steps: an IP address allotment request is
sent to the DHCP server when the PC boots up, the DHCP server that received the request transmits
network information such as the IP address to the PC, and the transmitted network information is
automatically registered to the network settings on the PC. The DHCP service is convenient and useful
especially in an environment where multiple PCs are used. Theoretically, the IP address changes each
time the PC boots up (or an IP allotment request is sent); in many cases, however, the existing IP address
is re-allotted. An Internet router performs two roles: creating a private IP address (NAT service) and
automatically allotting the IP address to each PC (DHCP service) at the same time.
When using your HUB Monitor's or notebook PC’s LAN network, ensure you insert a LAN cable into
only one device. Otherwise, a system crash may occur.
Dynamic IP User
1
2
To use a dynamic IP address, connect a LAN to your HUB Monitor.
Next, go to the network settings menu and activate the HUB Monitor's network device (select
“Use”).
2 Using "HUB Monitor"
43
2
Using "HUB Monitor"
Go to Control Panel
→
Network and Internet
→
Network and Sharing Center
→
Change
adapter settings. Next, right-click on the HUB Monitor's network device (marked “LAN9512/
LAN9514 USB 2.0 to Ethernet 10/100 Adapter #7”) and select Use.
3
Using the network properties menu, check that the IP address mode for the HUB Monitor's network
device is set to Auto.
Go to Control Panel
→
Network and Internet
→
Network and Sharing Center
→
Change
adapter settings. Next, right-click on the HUB Monitor's network device (marked “LAN9512/
LAN9514 USB 2.0 to Ethernet 10/100 Adapter #7”).
Select Properties
→
Internet Protocol Version 4 (TCP/IPv4)
→
Properties.
2.5.2 Static IP
To configure the IP address (private or official) on your PC, someone (mostly a server system) must
distribute and allot an IP address to the PC. An official IP address is allotted by your Internet service
provider, and a private IP address is allotted by your Internet router. You can select whether to configure
the IP address on the PC automatically or manually. The static IP address mode is used to manually enter
an IP address. The static IP address mode is suitable if the IP address for the PC should not be changed
(such as for a file sharing server) and generally is not used, except under such special circumstances.
When using your HUB Monitor's or notebook PC’s LAN network, ensure you insert a LAN cable into
only one device. Otherwise, a system crash may occur.
2 Using "HUB Monitor"
44
2
Using "HUB Monitor"
Static IP User
1
2
Set the LAN network for the notebook PC to Do not use.
Go to Control Panel
→ Network and Internet → Network and Sharing Center → Change
adapter settings. Next, right-click on the notebook PC’s network device and select Do not use.
3
Right-click on the HUB Monitor's network device (marked “LAN9512/LAN9514 USB 2.0 to Ethernet
10/100 Adapter #7”), and select Use.
Be sure to perform this process before configuring the IP.
4
Configure the static IP. Assign the static IP that is allotted to the HUB Monitor's network device.
Go to Control Panel
→
Network and Internet
→
Network and Sharing Center
→
Change
adapter settings. Next, right-click on the HUB Monitor's network device (marked “LAN9512/
LAN9514 USB 2.0 to Ethernet 10/100 Adapter #7”), select Properties
Version 4 (TCP/IPv4)
→
→
Internet Protocol
Properties, and configure the static IP and DNS settings.
2 Using "HUB Monitor"
45
2
Using "HUB Monitor"
5
After configuring the IP, click OK. The following message will appear.
A static IP must be allotted to only one network device. The following message will appear if the
same static IP is allotted to the network devices of both the notebook PC and HUB Monitor.
(Ensure the network device that is not in use is set to Do not use.)
Select No in the message window.
To use the notebook PC’s LAN network, set the HUB Monitor's network to Do not use and the
notebook PC’s network device to Use. Next, configure the IP settings.
6
Click Close.
2 Using "HUB Monitor"
46
2
2.6
Using "HUB Monitor"
Notice before your use of Wireless USB or USB Mode
1
Most games require a high resolution and fast response time. When you play a game, it is
recommended that you use Analog or HDMI mode instead of Wireless USB or USB mode. Note that
playing a game or movie is not supported in Wireless USB or USB mode on a Windows XP or VISTA
operating system.
2
Recognizing the Wireless USB or USB mode may take awhile if the mode is used for the first time or
the standby mode is deactivated on the PC.
3
To use the USB HUB function when the monitor is in USB mode (when the monitor is connected to
the USB 2.0 port on the PC) or in Wireless USB mode, it is best to connect a USB cable to the black
USB 2.0 port on the monitor.
4
If the PC enters Standby mode when the monitor is in Wireless USB mode, the wireless connection
will be disconnected and the USB HUB function will be disabled.
2 Using "HUB Monitor"
47
3
3.1
Connecting and Using a Source Device
Before Connecting
3.1.1 Pre-connection Checkpoints
z
Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
z
Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
z
Check the types of ports at the back of the product you want to connect.
3 Connecting and Using a Source Device
48
3
3.2
Connecting and Using a Source Device
Connecting and Using a PC
3.2.1 Connecting to a PC
z
Select a connection method suitable for your PC.
Connecting parts may differ in different products.
Connection using the D-SUB cable (analogue type)
RGB IN
1
Connect the D-SUB cable to the [RGB IN] port on the back of the product and the RGB port on the
PC.
2
Connect the DC power adapter to the product and a power socket, and turn on the power switch
on the PC.
(For details, refer to "3.4 Connecting the Power". )
3
Press [
] to change the input source to Analog.
Audio is not available if the PC and product are connected via the D-SUB port.
Connection Using an HDMI-DVI Cable
HDMI IN
1
Connect the HDMI-DVI cable to the [HDMI IN] port on the back of the product and the DVI port on
the PC.
2
Connect the DC power adapter to the product and a power socket, and turn on the power switch
on the PC.
(For details, refer to "3.4 Connecting the Power". )
3
Press [
] to change the input source to HDMI.
3 Connecting and Using a Source Device
49
3
Connecting and Using a Source Device
Audio is not available if the PC and product are connected via the HDMI-DVI port.
Connection Using an HDMI Cable (Digital Type)
HDMI IN
1
Connect the HDMI cable to the [HDMI IN] port on the back of the product and the HDMI port on the
PC.
2
Connect the DC power adapter to the product and a power socket, and turn on the power switch
on the PC.
(For details, refer to "3.4 Connecting the Power". )
3
Press [
] to change the input source to HDMI.
If audio is supported, the Volume (VOL) can be adjusted using the [
] buttons on the front of the
product.
3 Connecting and Using a Source Device
50
3
Connecting and Using a Source Device
3.2.2 Driver Installation
z
You can set the optimum resolution and frequency for this product by installing the corresponding
drivers for this product.
z
An installation driver is contained on the CD supplied with the product.
z
If the file provided is faulty, visit the Samsung homepage (http://www.samsung.com) and
download the file.
1
2
3
4
Insert the user manual CD provided with the product into the CD-ROM drive.
5
Go to Display Properties and check that the resolution and refresh rate are appropriate.
Click "Windows Driver".
Follow the instructions given on the screen to proceed with installation.
Select your product model from the list of models.
Refer to your Windows OS manual for further details.
3 Connecting and Using a Source Device
51
3
Connecting and Using a Source Device
3.2.3 Setting Optimum Resolution
An information message about setting optimum resolution will appear if you power on the product for the
first time after purchase.
Select a language and change the resolution to the optimum value.
The optimal resolution for this monitor is as follows:
1920 x 1080 60Hz
Follow the above settings to set the resolution.
English
AUTO
1
2
Press [
] to move to the language you want and press the [
].
To hide the information message, press [ MENU ].
z
If the optimum resolution is not selected, the message will appear up to three times for a specified
time even when the product is turned off and on again.
z
The optimum resolution (1920 x 1080) can also be selected in Control Panel on your PC.
3 Connecting and Using a Source Device
52
3
Connecting and Using a Source Device
3.2.4 Changing the Resolution Using a PC
z
Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture
quality.
z
The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected.
Changing the Resolution on Windows XP
Go to Control Panel
Display
Settings and change the resolution.
3 Connecting and Using a Source Device
53
3
Connecting and Using a Source Device
Changing the Resolution on Windows Vista
Go to Control Panel
Personalization
Display Settings and change the resolution.
3 Connecting and Using a Source Device
54
3
Connecting and Using a Source Device
Changing the Resolution on Windows 7
Go to Control Panel
Display
Screen Resolution and change the resolution.
3 Connecting and Using a Source Device
55
3
3.3
Connecting and Using a Source Device
Connecting Headphones
z
Connect an audio output device such as headphones or speakers to [
] on the product.
Headphones will function properly if the product is connected to a PC via USB, Wireless USB or HDMI.
3 Connecting and Using a Source Device
56
3
3.4
Connecting and Using a Source Device
Connecting the Power
Put the DC power adapter in the groove, with the switch
facing upward.
- Push the adapter until you hear a “click.”
Connect the power cable to the DC power adapter. Next,
connect the DC power adapter to the product.
Plug in the power cable to the power socket.
- Removing the DC power adapter
To remove the DC power adapter, lift it outwards from the
bottom as shown in the image.
When using the adapter without fixing it to the back of the monitor, the adapter jack can easily get
disconnected or the cable may break. Be sure to securely fix the adapter in the groove.
3 Connecting and Using a Source Device
57
4
4.1
Screen Setup
Configure the screen settings such as brightness and color tone.
MAGIC
This feature provides the viewing angle, brightness, and tint to suit your preferences.
4.1.1
SAMSUNG MAGIC Bright
This menu provides an optimum picture quality suitable for the environment where the product will be
used.
z
z
SAMSUNG
Sub-options under MAGIC
Bright may vary depending on the settings of "PC/AV Mode." (See
"Chapter 7. SETUP&RESET.")
This menu is not available when Eco Light Sensor or Eco Saving is set to On.
SAMSUNG
Configuring MAGIC
Bright
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to PICTURE and press [
Press [
] to move to MAGIC and press [
Press [
SAMSUNG
] to move to MAGIC
Bright and press [
] on the product.
] on the product.
] on the product. The following screen will
appear.
[In PC mode]
MAGIC
SAMSUNG
MAGIC Bright
SAMSUNG
MAGIC Color
Return
: Custom
Standard
: Game
Cinema
Dynamic Contrast
Adjust
AUTO
Enter
z
Custom: Customize the contrast and brightness as required.
z
Standard: Obtain a picture quality suitable for editing documents or using Internet.
z
Game: Obtain a picture quality suitable for playing games that involve many graphic effects and
dynamic movements.
z
Cinema: Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD
content.
4 Screen Setup
58
4
Screen Setup
z
Dynamic Contrast: Obtain balanced brightness through automatic contrast adjustment.
[In AV mode]
MAGIC
SAMSUNG
MAGIC Bright
SAMSUNG
MAGIC Color
: Dynamic
Standard
: Movie
Custom
Return
5
6
Adjust
AUTO
Enter
z
Dynamic: This mode is suitable when the ambient light is bright.
z
Standard: This mode is generally suitable for any environment.
z
Movie: This mode reduces eye fatigue.
z
Custom: Customize the contrast and brightness as required.
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
4 Screen Setup
59
4
Screen Setup
4.1.2
SAMSUNG MAGIC Color
SAMSUNG
MAGICColor
is a new picture-quality improvement technology developed independently by Samsung,
which delivers vivid natural colors without picture quality degradation.
SAMSUNG
This menu is not available when MAGIC
Bright is in Cinema or Dynamic Contrast mode.
SAMSUNG
Configuring MAGIC
Color
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to PICTURE and press [
Press [
] to move to MAGIC and press [
Press [
SAMSUNG
] on the product.
] on the product.
] to move to MAGICColor and press [
] on the product. The following screen will
appear.
MAGIC
SAMSUNG
MAGIC Bright
: Custom
SAMSUNG
: Off
Demo
Full
Intelligent
MAGIC Color
Return
5
6
Adjust
AUTO
Enter
SAMSUNG
z
Off: Disable MAGICColor.
z
SAMSUNG
Demo: Compare normal screen mode with MAGIC
Color mode.
z
Full: Obtain a vivid picture quality for all areas including the flesh colors in the picture.
z
Intelligent: Improve the chroma for all areas except the flesh colors in the picture.
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
4 Screen Setup
60
4
4.2
Screen Setup
Brightness
Adjust the general brightness of the picture. (Range: 0~100)
A higher value will make the picture appear brighter.
z
SAMSUNG
This menu is not available when MAGIC
Bright is set to Dynamic Contrast mode.
z
This menu is not available when Eco Light Sensor or Eco Saving is set to On.
4.2.1 Configuring Brightness
1
2
3
Press [ MENU ] on the product.
Press [
] to move to PICTURE and press [
Press [
] to move to Brightness and press [
] on the product.
] on the product. The following screen will
appear.
PICTURE
MAGIC
Brightness
50
Contrast
75
Sharpness
60
Coarse
2200
Fine
0
Response Time
Faster
AUTO
4
Adjust the Brightness using the [
] button.
4 Screen Setup
61
4
4.3
Screen Setup
Contrast
Adjust the contrast between the objects and background. (Range: 0~100)
A higher value will increase the contrast to make the object appear clearer.
z
SAMSUNG
This menu is not available when MAGIC
Bright is in Cinema or Dynamic Contrast mode.
z
SAMSUNG
This menu is not available when MAGIC
Color is in Full or Intelligent mode.
4.3.1 Configuring Contrast
1
2
3
Press [ MENU ] on the product.
Press [
] to move to PICTURE and press [
Press [
] to move to Contrast and press [
] on the product.
] on the product. The following screen will appear.
PICTURE
MAGIC
Brightness
50
Contrast
75
Sharpness
60
Coarse
2200
Fine
0
Response Time
Faster
Return
4
Adjust the Contrast using the [
Adjust
AUTO
Enter
] button.
4 Screen Setup
62
4
4.4
Screen Setup
Sharpness
Make the outline of objects more clear or blurry. (Range: 0~100)
A higher value will make the outline of objects clearer.
z
SAMSUNG
This menu is not available when MAGIC
Bright is in Cinema or Dynamic Contrast mode.
z
SAMSUNG
This menu is not available when MAGIC
Color is in Full or Intelligent mode.
4.4.1 Configuring Sharpness
1
2
3
Press [ MENU ] on the product.
Press [
] to move to PICTURE and press [
Press [
] to move to Sharpness and press [
] on the product.
] on the product. The following screen will
appear.
PICTURE
MAGIC
Brightness
50
Contrast
75
Sharpness
60
Coarse
2200
Fine
0
Response Time
Faster
Return
4
Adjust the Sharpness using the [
Adjust
AUTO
Enter
] button.
4 Screen Setup
63
4
4.5
Screen Setup
Coarse
Adjust the screen frequency.
Only available in Analog mode.
4.5.1 Adjusting Coarse
1
2
3
Press [ MENU ] on the product.
Press [
] to move to PICTURE and press [
Press [
] to move to Coarse and press [
] on the product.
] on the product. The following screen will appear.
PICTURE
MAGIC
Brightness
50
Contrast
75
Sharpness
60
Coarse
2200
Fine
0
Response Time
Faster
Return
4
Adjust the Coarse using the [
Adjust
AUTO
Enter
] button.
4 Screen Setup
64
4
4.6
Screen Setup
Fine
Fine-adjust the screen to obtain a vivid picture.
Only available in Analog mode.
4.6.1 Adjusting Fine
1
2
3
Press [ MENU ] on the product.
Press [
] to move to PICTURE and press [
Press [
] to move to Fine and press [
] on the product.
] on the product. The following screen will appear.
PICTURE
MAGIC
Brightness
50
Contrast
75
Sharpness
60
Coarse
2200
Fine
0
Response Time
Faster
Return
4
Adjust the Fine using the [
Adjust
AUTO
Enter
] button.
4 Screen Setup
65
4
4.7
Screen Setup
Response Time
Accelerate the panel response rate to make video appear more vivid and natural.
z
It is best to set Response Time to Normal or Faster when you are not viewing a movie.
z
The functions available on the monitor may vary depending on the model. Refer to the actual
product.
4.7.1 Configuring Response Time
1
2
3
Press [ MENU ] on the product.
Press [
] to move to PICTURE and press [
] on the product.
Press [
] to move to Response Time and press [
] on the product. The following screen will
appear.
PICTURE
MAGIC
Brightness
50
Contrast
75
Sharpness
60
Coarse
2200
Fine
Normal
Faster
Fastest
Response Time
Return
4
5
Press [
Adjust
] to move to the option you want and press the [
AUTO
Enter
].
The selected option will be applied.
4 Screen Setup
66
5
Configuring Tint
SAMSUNG
Adjust the tint of the screen. This menu is not available when MAGIC
Bright is set to Cinema or
Dynamic Contrast mode.
Red
Adjust the value of the color red in the picture. (Range: 0~100)
A higher value will increase the intensity of the color.
SAMSUNG
This menu is not available when MAGIC
Color is in Full or Intelligent mode.
5.1.1 Configuring Red
1
2
3
Press [ MENU ] on the product.
Press [
] to move to COLOR and press [
Press [
] to move to Red and press [
] on the product.
] on the product. The following screen will appear.
COLOR
Red
50
Green
50
Blue
Color Tone
Normal
Gamma
5.1
Mode1
50
AUTO
4
Adjust the Red using the [
] button.
5 Configuring Tint
67
5
Green
Adjust the value of the color green in the picture. (Range: 0~100)
A higher value will increase the intensity of the color.
SAMSUNG
This menu is not available when MAGIC
Color is in Full or Intelligent mode.
5.2.1 Configuring Green
1
2
3
Press [ MENU ] on the product.
Press [
] to move to COLOR and press [
Press [
] to move to Green and press [
] on the product.
] on the product. The following screen will appear.
COLOR
Red
50
Green
50
Blue
Color Tone
Normal
Gamma
5.2
Configuring Tint
Mode1
50
AUTO
4
Adjust the Green using the [
] button.
5 Configuring Tint
68
5
Blue
Adjust the value of the color blue in the picture. (Range: 0~100)
A higher value will increase the intensity of the color.
SAMSUNG
This menu is not available when MAGIC
Color is in Full or Intelligent mode.
5.3.1 Configuring Blue
1
2
3
Press [ MENU ] on the product.
Press [
] to move to COLOR and press [
Press [
] to move to Blue and press [
] on the product.
] on the product. The following screen will appear.
COLOR
Red
50
Green
50
Blue
Color Tone
Normal
Gamma
5.3
Configuring Tint
0RGH
50
AUTO
4
Adjust the Blue using the [
] button.
5 Configuring Tint
69
5
Color Tone
Adjust the general color tone of the picture.
SAMSUNG
This menu is not available when MAGIC
Color is in Full or Intelligent mode.
5.4.1 Configuring the Color Tone Settings
1
2
3
Press [ MENU ] on the product.
Press [
] to move to COLOR and press [
Press [
] to move to Color Tone and press [
] on the product.
] on the product. The following screen will
appear.
COLOR
Red
Green
50
Blue
50
Color Tone
Gamma
5.4
Configuring Tint
50
Cool 2
Cool 1
Normal
Warm 1
Warm 2
Custom
AUTO
4
5
z
Cool2: Set the color temperature to be cooler than Cool1.
z
Cool1: Set the color temperature to be cooler than Normal mode.
z
Normal: Display the standard color tone.
z
Warm1: Set the color temperature to be warmer than Normal mode.
z
Warm2: Set the color temperature to be warmer than Warm1.
z
Custom: Customize the color tone.
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
5 Configuring Tint
70
5
Gamma
Adjust the mid-range brightness (Gamma) of the picture.
5.5.1 Configuring Gamma
1
2
3
Press [ MENU ] on the product.
Press [
] to move to COLOR and press [
] on the product.
Press [
] to move to Gamma and press [
] on the product. The following screen will appear.
COLOR
Red
50
Green
50
Blue
Color Tone
Normal
Gamma
5.5
Configuring Tint
Mode1
Mode2
Mode3
50
AUTO
4
5
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
5 Configuring Tint
71
6
6.1
Resizing or Relocating the Screen
Image Size
Change the picture size.
6.1.1 Changing the Picture Size
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SIZE&POSITION and press [
Press [
] to move to Image Size and press [
] on the product.
] on the product. The following screen will
appear.
SIZE&POSITION
H-Position
Auto
Wide
V-Position
Menu H-Position
Menu V-Position
Image Size
Return
50
50
10
AUTO
Adjust
Enter
z
Auto: Display the picture according to the aspect ratio of the input source.
z
Wide: Display the picture in full screen regardless of the aspect ratio of the input source.
SIZE&POSITION
Image Size
H-Position
4:3
16 : 9
Screen Fit
V-Position
Menu H-Position
50
Menu V-Position
10
Return
AUTO
Adjust
Enter
z
4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
z
16:9: Display the picture with an aspect ratio of 16:9. Suitable for DVD content or widescreen
broadcasts.
z
Screen Fit: Display the picture with the original aspect ratio without cutting off.
Requirements to activate Image Size
4
5
z
When connecting to digital output device via DVI/HDMI cable
z
When signal resolution is 480p, 576p , 720p, 1080i, 1080p
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
6 Resizing or Relocating the Screen
72
6
6.2
Resizing or Relocating the Screen
H-Position & V-Position
H-Position: Move the screen to the left or right.
V-Position: Move the screen up or down.
z
This menu is only available when Image Size is set to Screen Fit.
z
Only available in Analog mode.
6.2.1 Configuring H-Position & V-Position
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SIZE&POSITION and press [
] on the product.
Press [
] to move to H-Position or V-Position, and press [
]. The following screen will
appear.
SIZE&POSITION
Image Size
Wide
Image Size
Wide
H-Position
50
H-Position
50
V-Position
50
V-Position
50
Menu H-Position
50
Menu H-Position
50
Menu V-Position
10
Menu V-Position
10
Return
4
SIZE&POSITION
Press [
Adjust
AUTO
Enter
Return
Adjust
AUTO
Enter
] to configure H-Position or V-Position.
6 Resizing or Relocating the Screen
73
6
6.3
Resizing or Relocating the Screen
Menu H-Position & Menu V-Position
Menu H-Position: Move the menu position to the left or right.
Menu V-Position: Move the menu position up or down.
6.3.1 Configuring Menu H-Position & Menu V-Position
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SIZE&POSITION and press [
] on the product.
Press [
] to move to Menu H-Position or Menu V-Position, and press [
]. The following
screen will appear.
SIZE&POSITION
SIZE&POSITION
Image Size
Wide
Image Size
Wide
H-Position
50
H-Position
50
V-Position
50
V-Position
50
Menu H-Position
50
Menu H-Position
50
Menu V-Position
10
Menu V-Position
10
Return
4
Press [
Adjust
AUTO
Enter
Return
Adjust
AUTO
Enter
] to configure Menu H-Position or Menu V-Position.
6 Resizing or Relocating the Screen
74
7
7.1
Setup and Reset
HUB
Configure the settings to use the HUB function on the product.
Refer to "Chapter 2. HUB Monitor" for details about how to use the HUB function.
7.1.1
Auto Wireless Detection
If the product is connected to a PC via Wireless USB, it will automatically detect the Wireless USB signal
and change the input source to Wireless USB mode.
Configuring Auto Wireless Detection
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
] on the product.
Press [
] to move to HUB and press [
Press [
] to move to Auto Wireless Detection and press [
] on the product.
] on the product. The following
screen will appear.
HUB
Wireless Connection
: Off
On
:
USB Connection
: Disconnected
Analog
: Disconnected
HDMI
: Disconnected
USB Super Charging
: Off
Wireless ID
: -----------------
Auto Wireless Detection
AUTO
z
Off: Deactivate Auto Wireless Detection
z
On: Automatically detect a Wireless USB signal and change the input source to Wireless USB
mode.
5
6
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
7 Setup and Reset
75
7
Setup and Reset
7.1.2
Wireless Connection
You can view the status of the Wireless USB connection between the product and a PC.
Selecting the Wireless Connection option. The input source will change to Wireless USB mode.
z
The connection status will be shown even when the input source is not Wireless USB mode.
z
Selecting Wireless Connection when a Wireless USB connection is established will automatically
change the input source to Wireless USB mode.
Activating Wireless Connection
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to HUB and press [
] on the product.
] on the product. A message will appear indicating
that a Wireless USB connection is established or disconnected.
4
If a Wireless USB connection is established, press [
[
] to move to Wireless Connection and press
]. The input source will automatically switch to Wireless USB mode.
+8%
$XWR:LUHOHVV'HWHFWLRQ
2II
:LUHOHVV&RQQHFWLRQ
&RQQHFWHG
86%&RQQHFWLRQ
'LVFRQQHFWHG
$QDORJ
'LVFRQQHFWHG
+'0,
'LVFRQQHFWHG
86%6XSHU&KDUJLQJ
2II
:LUHOHVV,'
AUTO
7 Setup and Reset
76
7
Setup and Reset
7.1.3
USB Connection
You can view the USB cable connection status between the product and a PC.
z
The connection status will be shown even when the input source is not USB mode.
z
Selecting USB Connection when a USB cable is connected will automatically change the input
source to USB mode.
Configuring USB Connection
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to HUB and press [
] on the product.
] on the product. A message will appear indicating
that a USB cable is connected or disconnected.
4
If a USB cable is connected, press [
] to move to USB Connection and press [
]. The input
source will automatically switch to USB mode.
+8%
$XWR:LUHOHVV'HWHFWLRQ
2II
:LUHOHVV&RQQHFWLRQ
'LVFRQQHFWHG
86%&RQQHFWLRQ
&RQQHFWHG
$QDORJ
'LVFRQQHFWHG
+'0,
'LVFRQQHFWHG
86%6XSHU&KDUJLQJ
2II
:LUHOHVV,'
AUTO
7 Setup and Reset
77
7
Setup and Reset
7.1.4
Analog
You can view the Analog cable connection status between the product and a PC.
z
The connection status will be shown even when the input source is not Analog mode.
z
Selecting the Analog option when an analog cable is connected will automatically change the input
source to Analog mode.
Configuring Analog
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to HUB and press [
] on the product.
] on the product. A message will appear indicating
that an analog cable is connected or disconnected.
4
If an analog cable is connected, press [
] to move to Analog and press [
]. The input source
will automatically switch to Analog mode.
HUB
Auto Wireless Detection
Off
Wireless Connection
Disconnected
USB Connection
Disconnected
Analog
Connected
HDMI
Disconnected
USB Super Charging
Off
Wireless ID
-----------------
ࢇࢷ֩Ѝ
ࢇࢷ֩Ѝ
࣏ࢽ
ࢇѰ
AUTO
۴੔
7 Setup and Reset
78
7
Setup and Reset
7.1.5
HDMI
You can view the HDMI connection status between the product and an AV device.
z
The connection status will be shown even when the input source is not HDMI mode.
z
Selecting the HDMI option when an HDMI cable is connected will automatically change the input
source to HDMI mode.
Configuring HDMI
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to HUB and press [
] on the product.
] on the product. A message will appear indicating
that an HDMI cable is connected or disconnected.
4
If an HDMI cable is connected, press [
] to move to HDMI and press [
]. The input source
will automatically switch to HDMI mode.
HUB
Auto Wireless Detection
: Off
Wireless Connection
: Disconnected
USB Connection
: Disconnected
Analog
: Disconnected
HDMI
: Connected
USB Super Charging
: Off
Wireless ID
: -----------------
ࢇࢷ֩Ѝ
ࢇࢷ֩Ѝ
࣏ࢽ
ࢇѰ
AUTO
۴੔
7 Setup and Reset
79
7
Setup and Reset
7.1.6
USB Super Charging
A source device's battery can be charged quickly via USB 3.0 port on the product.
z
Data transmission is not available if USB Super Charging is on.
z
To enable standard charging or data transmission, set USB Super Charging to off.
z
The input source does not need to be changed.
Configuring USB Super Charging
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to HUB and press [
Press [
] to move to USB Super Charging and press [
] on the product.
] on the product.
] on the product. The following
screen will appear.
HUB
Auto Wireless Detection
: 2II
Wireless Connection
: 'LVFRQQHFWHG
USB Connection
: 'LVFRQQHFWHG
Analog
: 'LVFRQQHFWHG
HDMI
: 'LVFRQQHFWHG
USB Super Charging
: 2II
1SRUW
:
2SRUWV
Wireless ID
ࢇࢷ ֩Ѝ
AUTO۴੔
z
Off: Deactivate USB Super Charging
z
1 Port: Enable a single USB 3.0 port (marked with a charging icon) for quick battery charging.
Only the USB 3.0 port marked [
z
5
6
ࢇѰ
] supports high-speed battery charging
2 Ports: Enable two USB 3.0 ports for quick battery charging.
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
7.1.7
Wireless ID
Wireless ID is a unique ID assigned to a monitor. The "Samsung HUB Monitor Setup" program reads the
ID and identifies each of nearby monitors. The ID is shown in the "Samsung HUB Monitor Setup"
program and in the lower part of the HUB menu.
7 Setup and Reset
80
7
7.2
Setup and Reset
ECO
The Eco Motion Sensor, Eco Light Sensor, and Eco Saving options are displayed on the same menu
page so that you can conveniently configure the power saving settings.
7.2.1
Eco Motion Sensor
The Eco Motion Sensor activates to save power when it does not detect any movement within a
specified area for a specified period of time.
Eco Motion Sensor is not available when the monitor is used in portrait mode.
Configuring Eco Motion Sensor
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
] on the product.
Press [
] to move to ECO and press [
Press [
] to move to Eco Motion Sensor and press [
] on the product.
]. The following screen will appear.
ECO
Eco Motion Sensor
೛%DFNOLJKW
(FR/LJKW6HQVRU
▶6HQVLWLYLW\
5Off
Min
5 Min
ଥࢿ
10 Min
20 Min
30 Min
1h
▶%ULJKWQHVV/HYHO
(FR6DYLQJ
Off
(FR,FRQ'LVSOD\
Off
Return
Move
AUTO
Enter
This option is disabled if the product is connected to a PC that is in power-saving mode.
z
Off: Deactivate the Eco Motion Sensor function.
z
5 Min: Automatically turn off the power if the sensor has not detected any movement of an
object or person for 5 minutes within the specified range of detection.
z
10 Min: Automatically turn off the power if the sensor has not detected any movement of an
object or person for 10 minutes within the specified range of detection.
z
20 Min: Automatically turn off the power if the sensor has not detected any movement of an
object or person for 20 minutes within the specified range of detection.
z
30 Min: Automatically turn off the power if the sensor has not detected any movement of an
object or person for 30 minutes within the specified range of detection.
z
1 h : Automatically turn off the power if the sensor has not detected any movement of an object
or person for 1 hour within the specified range of detection.
5
6
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
7 Setup and Reset
81
7
Setup and Reset
Configuring Backlight
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to ECO and press [
Press [
] to move to Backlight and press [
] on the product.
] on the product.
] on the product. The following screen will
appear.
ECO
Eco Motion Sensor
5 Min
▶Backlight
ଥࢿ
Off
Dimming
(FR/LJKW6HQVRU
▶6HQVLWLYLW\
▶%ULJKWQHVV/HYHO
(FR6DYLQJ
Off
(FR,FRQ'LVSOD\
Off
Return
Move
AUTO
Enter
Off: Turn off the screen and activate DPMS mode. If Off is selected, it takes several seconds for
z
the monitor to detect movement and turn on after it turned off.
Dimming: Reduce the brightness of the screen (still turned on).
z
5
6
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
z
The performance of Eco Motion Sensor is maximized to a specific user distance (1m) and angle (40
degrees).
z
The sensor may not detect you if you are motionless.
z
If you think that the mode entry message appears too frequently, increase the time setting of the
Eco Motion Sensor or turn the Eco Icon Display Off.
z
Avoid using radio equipment such as a walkie-talkie near the product as this may cause a product
malfuction.
7 Setup and Reset
82
7
Setup and Reset
7.2.2
Eco Light Sensor
The Eco Light Sensor feature optimizes the view condition and contributes to power saving by adjusting
the screen brightness depending on the ambient light intensity.
z
SAMSUNG
This menu is not available when MAGIC
Bright is in Dynamic Contrast mode.
z
This menu is not available when Eco Saving is set .
Configuring Eco Light Sensor
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
] on the product.
Press [
] to move to ECO and press [
Press [
] to move to Eco Light Sensor and press [
] on the product.
]. The following screen will appear.
(&2
Eco Motion Sensor
0LQ
೛%DFNOLJKW
2II
(FR/LJKW6HQVRU
೛6HQVLWLYLW\
2II
2Q
೛%ULJKWQHVV/HYHO
(FR6DYLQJ
2II
(FR,FRQ'LVSOD\
2II
5HWXUQ
5
6
0RYH
AUTO
(QWHU
z
Off: Deactivate the Eco Light Sensor function.
z
On: Automatically adjust the brightness according to the ambient light intensity.
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
7 Setup and Reset
83
7
Setup and Reset
Configuring Sensitivity
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to ECO and press [
Press [
] to move to Sensitivity and press [
] on the product.
] on the product.
] on the product. The following screen will
appear.
(&2
Eco Motion Sensor
0LQ
೛%DFNOLJKW
2II
(FR/LJKW6HQVRU
2Q
೛6HQVLWLYLW\
೛%ULJKWQHVV/HYHO
+LJK
0HGLXP
/RZ
(FR6DYLQJ
(FR,FRQ'LVSOD\
5HWXUQ
z
2II
0RYH
AUTO
(QWHU
High: High sensitivity that maximizes the varying level of screen brightness depending on the
ambient light intensity.
z
Medium: Intermediate sensitivity that sets a varying level of screen brightness between High and
Low depending on the ambient light intensity.
z
Low: Low sensitivity that minimizes the varying level of screen brightness depending on the
ambient light intensity.
5
6
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
7 Setup and Reset
84
7
Setup and Reset
Configuring Brightness Level
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to ECO and press [
Press [
] to move to Brightness Level and press [
] on the product.
] on the product.
] on the product. The following screen will
appear.
(&2
Eco Motion Sensor
0LQ
೛%DFNOLJKW
2II
(FR/LJKW6HQVRU 2Q
೛6HQVLWLYLW\
+LJK
೛%ULJKWQHVV/HYHO
(FR6DYLQJ
(FR,FRQ'LVSOD\
5HWXUQ
5
6
%ULJKWHU
&XUUHQW
'LPPHU
2II
0RYH
z
Brighter: Increase the current brightness of the screen.
z
Current: Maintain the current brightness of the screen.
z
Dimmer: Decrease the current brightness of the screen.
Press [
] to move to the option you want and press the [
AUTO
(QWHU
].
The selected option will be applied.
7 Setup and Reset
85
7
Setup and Reset
7.2.3
Eco Saving
The Eco Saving function reduces power consumption by controlling the electric current used by the
monitor panel.
z
SAMSUNG
This menu is not available when MAGIC
Bright is in Dynamic Contrast mode.
z
This menu is not available when Eco Light Sensor is set.
Configuring Eco Saving
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to ECO and press [
Press [
] to move to Eco Saving and press [
] on the product.
] on the product.
] on the product. The following screen will
appear.
ECO
Eco Motion Sensor
Off
▶Backlight
(FR/LJKW6HQVRU
Off
▶6HQVLWLYLW\
▶%ULJKWQHVV/HYHO
(FR6DYLQJ
(FR,FRQ'LVSOD\
ଥࢿ
Off
Return
5
6
Move
AUTO
Enter
z
75% : Change the monitor power consumption to 75% of the default level.
z
50% : Change the monitor power consumption to 50% of the default level.
z
Off: Deactivate the Eco Saving function.
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
7 Setup and Reset
86
7
Setup and Reset
7.2.4
Eco Icon Display
Configuring Eco Icon Display
1
2
3
4
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
] on the product.
Press [
] to move to ECO and press [
Press [
] to move to Eco Icon Display and press [
] on the product.
]. The following screen will appear.
(&2
Eco Motion Sensor
0LQ
▶Backlight
2II
(FR/LJKW6HQVRU
2II
▶6HQVLWLYLW\
▶%ULJKWQHVV/HYHO
(FR6DYLQJ
(FR,FRQ'LVSOD\
5HWXUQ
5
6
2II
2Q
0RYH
AUTO
(QWHU
z
Off: Disable the Eco Icon Display function.
z
On: Display the operation status of the Eco sensor as a pop-up guide.
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
Notes
Eco Motion Sensor Activated
w–žŒ™Gv
z
sec
If the monitor is left idle for the period of time to which the off timer is configured when Eco Motion
Sensor is enabled, Eco Motion Sensor will activate and switch the monitor to power-saving mode.
z
A 10-second countdown timer will start along with the above picture before the power-saving mode
activates showing the operation status of the Eco Motion Sensor.
Eco Light Sensor Activated
z
Eco Light Sensor Activated
If the screen brightness is adjusted according to the ambient light intensity when the Eco Light
Sensor is on, a pop-up as shown above will appear showing the adjusting screen brightness.
z
If the screen becomes brighter as the ambient light becomes brighter, the brightness slide bar level
will increase with a sun image displayed. If the screen becomes darker, the brightness slide bar level
7 Setup and Reset
87
7
Setup and Reset
will decrease with a moon image displayed. The brightness slide bar will be displayed for 3 seconds
after the sensor activates.
You've saved
* tree(s).
z
A pop-up as shown above will appear when an energy tree completes while Eco Icon Display is On.
If the above picture is displayed, it means the Eco Icon Display option is On. Change this setting to
Off if you do not want to display the pop-up.
z
The amount of energy saved by the Eco Motion Sensor, Eco Light Sensor, and Eco Saving functions
will accumulate and the progress can be viewed as a growing energy tree.
The energy tree grows as the energy savings of the monitor accumulate. Accordingly, the tree's
growth will also be affected by other functions that involve power consumption such as the
brightness control function.
z
The amount of energy savings accumulated by using the power-saving functions, such as Eco
Motion Sensor, Eco Light Sensor and Eco Saving, will be calculated and represented as an amount
of carbon dioxide.
z
A complete energy tree will be displayed when the amount of energy savings accumulates to as
much as the amount of carbon dioxide a tree absorbs in a year. This shows that your energy saving
is as effective as planting a tree so that you can easily understand the accumulation of energy
savings over time and its effect by viewing the progress of a tree growing.
z
The progress of a tree growing will be represented as 10 different images (stages). After one fullgrown tree is complete, the initial image will be restored and the number of trees will continue to
accumulate. The number for energy trees will be rounded to one decimal place.
7 Setup and Reset
88
7
7.3
Setup and Reset
Menu Transparency
Set the transparency for the menu windows:
7.3.1 Changing Menu Transparency
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to Menu Transparency and press [
] on the product.
] on the product. The following screen
will appear.
SETUP&RESET
▶
HUB
▶
ECO
Language
Off
Off
On
PC/AV Mode
PC
Auto Source
Manual
Display Time
20 sec
Menu Transparency
Return
4
5
Press [
Adjust
] to move to the option you want and press the [
AUTO
Enter
].
The selected option will be applied.
7 Setup and Reset
89
7
7.4
Setup and Reset
Language
Set the menu language.
z
A change to the language setting will only be applied to the onscreen menu display.
z
It will not be applied to other functions on your PC.
7.4.1 Changing the Language
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to Language and press [
] on the product.
] on the product. The following screen will
appear.
SETUP&RESET
HUB
'HXWVFK
ECO
Menu Transparency
(VSDxRO
)UDQoDLV
ଞ˲߭
,WDOLDQR
Language
3ROVNL
PC/AV Mode
ƧNJLjLjǁƿǀ
Auto Source
7UNoH
Display Time
ᣣᧄ⺆
ଞ˲߭
∝䇁
Return
4
5
Press [
(QJOLVK
0DJ\DU
3RUWXJXrV
6YHQVND
Move
AUTO
Enter
] to move to the language you want and press the [
].
The selected option will be applied.
7 Setup and Reset
90
7
7.5
Setup and Reset
PC/AV Mode
Set PC/AV Mode to AV. The picture size will be enlarged. This option is useful when you view a movie.
PC/AV Mode is only available in HDMI mode.
7.5.1 Configuring PC/AV Mode
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to PC/AV Mode and press [
] on the product.
] on the product. The following screen will
appear.
SETUP&RESET
HUB
▶
▶
ECO
Menu Transparency
On
Language
English
PC/AV Mode
Auto Source
PC
AV
Manual
Display Time
20 sec
Return
4
5
Press [
Move
] to move to the option you want and press the [
AUTO
Enter
].
The selected option will be applied.
7 Setup and Reset
91
7
7.6
Setup and Reset
Auto Source
Activate Auto Source.
7.6.1 Configuring Auto Source
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to Auto Source and press [
] on the product.
] on the product. The following screen will
appear.
SETUP&RESET
೛
HUB
೛
ECO
Menu Transparency
On
Language
English
PC/AV Mode
PC
Auto Source
Auto
Manual
Display Time
Return
4
5
Move
z
Auto: The input source is automatically recognized.
z
Manual: Manually select an input source.
Press [
] to move to the option you want and press the [
AUTO
Enter
].
The selected option will be applied.
7 Setup and Reset
92
7
7.7
Setup and Reset
Display Time
Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified
period of time.
Display Time can be used to specify the time after which you want the OSD menu to disappear.
7.7.1 Configuring Display Time
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to Display Time and press [
] on the product.
] on the product. The following screen will
appear.
SETUP&RESET
೛
HUB
ECO
Menu Transparency
On
Language
English
PC/AV Mode
Manual
5 sec
10 sec
20 sec
200 sec
Auto Source
Display Time
Return
4
5
Press [
Move
] to move to the option you want and press the [
೛
AUTO
Enter
].
The selected option will be applied.
7 Setup and Reset
93
7
7.8
Setup and Reset
Key Repeat Time
Control the response rate of a button when the button is pressed.
7.8.1 Configuring Key Repeat Time
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to Key Repeat Time and press [
] on the product.
] on the product. The following screen
will appear.
SETUP&RESET
Key Repeat Time
Customized Key
Off Timer On/Off
Acceleration
1 sec
2
HUB
sec
No Repeat
Off Timer Setting
Reset
Return
z
Adjust
AUTO
Enter
Acceleration, 1 sec, or 2 sec can be selected. If No Repeat is selected, a command responds
only once when a button is pressed.
4
5
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
7 Setup and Reset
94
7
7.9
Setup and Reset
Customized Key
You can customize Customized Key as follows.
7.9.1 Configuring Customized Key
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
] on the product.
Press [
] to move to Customized Key and press [
] on the product. The following screen will
appear.
SETUP&RESET
Key Repeat Time
Acceleration
Customized Key
On
HUB
ECO
MAGIC
Image Size
Off Timer On/Off
Off Timer Setting
Reset
Return
z
4
5
Adjust
AUTO
Enter
HUB - ECO - MAGIC - Image Size
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
7 Setup and Reset
95
7
Setup and Reset
7.10 Off Timer On/Off
Enable or disable the off timer that automatically powers off the product.
7.10.1 Configuring Off Timer On/Off
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
] on the product.
Press [
] to move to Off Timer On/Off and press [
] on the product. The following screen will
appear.
SETUP&RESET
Key Repeat Time
Acceleration
Customized Key
HUB
Off Timer On/Off
Off
On
Off Timer Setting
Reset
Return
4
5
Adjust
AUTO
Enter
z
Off: Deactivate the off timer so that the product does not power off automatically.
z
On: Activate the off timer so that the product powers off automatically.
Press [
] to move to the option you want and press the [
].
The selected option will be applied.
7 Setup and Reset
96
7
Setup and Reset
7.11 Off Timer Setting
The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the
specified number of hours.
This menu is only available when Off Timer On/Off is set to On.
7.11.1 Configuring Off Timer Setting
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
] on the product.
Press [
] to move to Off Timer Setting and press [
] on the product. The following screen will
appear.
SETUP&RESET
Key Repeat Time
Acceleration
Customized Key
HUB
Off Timer On/Off
On
Off Timer Setting
10 h
Reset
Return
4
Press [
Adjust
AUTO
Enter
] to configure Off Timer Setting.
7 Setup and Reset
97
7
Setup and Reset
7.12 Reset
Return all the settings for the product to the default factory settings.
7.12.1 Initializing Settings (Reset)
1
2
3
Press [ MENU ] on the product.
Press [
] to move to SETUP&RESET and press [
Press [
] to move to Reset and press [
] on the product.
] on the product. The following screen will appear.
SETUP&RESET
Key Repeat Time
Acceleration
Customized Key
HUB
Off Timer On/Off
On
Off Timer Setting
Reset
Return
4
5
Press [
No
Yes
Adjust
] to move to the option you want and press the [
AUTO
Enter
].
The selected option will be applied.
7 Setup and Reset
98
8
8.1
INFORMATION Menu and Others
INFORMATION
View the current input source, frequency and resolution.
8.1.1 Displaying INFORMATION
1
2
Press [ MENU ] on the product.
Press [
] to move to INFORMATION. The current input source, frequency and resolution will
appear.
PICTURE
COLOR
Analog
SIZE&POSITION
67.6kHz 60Hz PP
1920 x 1080
SETUP&RESET
INFORMATION
EXIT
Exit
8.2
AUTO
Adjust
Enter
Configuring Brightness in the Startup Screen
Adjust Brightness using the [
] button in the startup screen where there is no on screen display menu
available.
1
Press [
] in the startup screen. The following screen will appear.
%ULJKWQHVV
100
EXIT
2
Adjust the Brightness using the [
] button.
Volume (VOL) can be adjusted if a cable is connected to the [HDMI IN] port.
8 INFORMATION Menu and Others
99
9
9.1
Troubleshooting Guide
Requirements Before Contacting Samsung Customer
Service Center
9.1.1 Testing the Product
Before calling Samsung Customer Service Center, test your product as follows. If the problem persists,
contact Samsung Customer Service Center.
Check if your product is operating normally by using the product test function.
If the screen is turned off and the power indicator blinks even though the product is properly connected
to a PC, perform a self-diagnosis test.
1
2
3
4
Power off both the PC and product.
Disconnect the cable from the product.
Power on the product.
If the Check Signal Cable message appears, the product is working normally.
If the screen remains blank, check the PC system, video controller and cable.
9.1.2 Checking the Resolution and Frequency
For a mode that exceeds the supported resolution (refer to "10.3 Standard Signal Mode Table"), the
message Not Optimum Mode. will appear for a short time.
9 Troubleshooting Guide
100
9
Troubleshooting Guide
9.1.3 Check the followings.
Installation issue (PC mode)
The screen keeps switching on and off.
Check the cable connection between the product
and PC, and ensure the connection is secure.
(Refer to "3.2 Connecting and Using a PC")
Blank spaces are found on all four sides of the
screen when an HDMI or HDMI-DVI cable is
connected to the monitor and PC.
The blank spaces found on the screen have
nothing to do with the monitor.
Blank spaces on the screen are caused by the PC
or graphics card. To resolve the problem, adjust
the screen size in the HDMI or DVI settings for the
graphics card. If the graphics card settings menu
does not have an option to adjust the screen size,
update the graphics card driver to the latest
version.
(Please contact the graphics card or computer
manufacturer for further details about how to
adjust the screen settings.)
Screen issue
The power LED is off. The screen will not switch
on.
Check that the power cable is connected
correctly (Refer to "3.2 Connecting and Using a
PC")
The message Check Signal Cable appears.
Check that the cable is properly connected to the
product. (Refer to "3.2 Connecting and Using a
PC")
Check that the device connected to the product is
powered on.
"Not Optimum Mode" is displayed.
This message appears if the signal from the
graphics card exceeds the maximum resolution or
frequency for the product.
Change the maximum resolution and frequency to
suit the product performance, referring to
Standard Signal Mode Table (107page).
The images on the screen look distorted.
Check the cable connection to the product (Refer
to "3.2 Connecting and Using a PC")
The screen is not clear. The screen is blurry.
Adjust Coarse(64page) and Fine(65page).
Remove any accessories (video extension cable,
etc) and try again.
Set the resolution and frequency to the
recommended level. (Refer to "10.1 General")
9 Troubleshooting Guide
101
9
Troubleshooting Guide
Screen issue
The screen appears unstable and shaky.
There are shadows or ghost images left on the
screen.
Check that the resolution and frequency for the
PC are within the range of resolution and
frequency compatible with the product, and if
required, change the settings, referring to
Standard Signal Mode Table (107page) in this
manual and the INFORMATION menu on the
product.
The screen is too bright. The screen is too dark.
Adjust Brightness(61page) and Contrast(62page).
Screen color is inconsistent.
Change the COLOR settings.
(Refer to " Configuring Tint")
The colors on the screen have a shadow and are
distorted.
Change the COLOR settings.
White does not really look white.
Change the COLOR settings.
(Refer to " Configuring Tint")
(Refer to " Configuring Tint")
There is no image on the screen and the power
LED blinks every 0.5 to 1 second.
The product is in power-saving mode.
Press any key on the keyboard or move the
mouse to return to the previous screen.
Sound issue
There is no sound.
Check the connection of the audio cable or adjust
the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the
maximum level, adjust the volume on your PC
sound card or software program.
Source device issue
A beeping sound is heard when my PC is booting. If a beeping sound is heard when your PC is
booting, have your PC serviced.
9 Troubleshooting Guide
102
9
9.2
Troubleshooting Guide
Q&A
Question
How can I change the
frequency?
Answer
Set the frequency on your graphics card.
z
Windows XP: Select Control Panel
Display
Settings
Appearance and Themes
Advanced
Monitor, and adjust Refresh rate
under Monitor settings.
z
Windows ME/2000: Select Control Panel
Advanced
z
Settings
Monitor, and adjust Refresh rate under Monitor settings.
Windows Vista: Select Control Panel
Personalization
Settings
z
Display
Personalization
Appearance and
Display Settings
Advanced
Monitor, and adjust Refresh rate under Monitor settings.
Windows 7: Select Control Panel
Display
Appearance and Personalization
Screen Resolution
Advanced settings
Monitor,
and adjust Refresh rate under Monitor settings.
How can I change the
resolution?
z
Windows XP: Go to Control Panel
Display
z
Appearance and Themes
Settings and adjust the resolution.
Windows ME/2000: Go to Control Panel
Display
Settings and
adjust the resolution.
z
Windows Vista: Go to Control Panel
Personalize
z
How do I set powersaving mode?
z
Display Settings and adjust the resolution.
Windows 7: Go to Control Panel
Display
Appearance and Personalization
Appearance and Personalization
Adjust Resolution and adjust the resolution.
Windows XP: Set power-saving mode in Control Panel
and Themes
Display
Appearance
Screen Saver Settings or BIOS SETUP on
the PC.
z
Windows ME/2000: Set power-saving mode in Control Panel
Display
Screen Saver Settings or BIOS SETUP on the PC.
z
Windows Vista: Set power-saving mode in Control Panel
Appearance and Personalization
Personalize
Screen Saver
Settings or BIOS SETUP on the PC.
z
Windows 7: Set power-saving mode in Control Panel
and Personalization
Personalize
Appearance
Screen Saver Settings or BIOS
SETUP on the PC.
Refer to the user manual for your PC or graphics card for further instructions on adjustment..
9 Troubleshooting Guide
103
10
Specifications
10.1 General
Model Name
Panel
Synchroni
zation
C27A650X / C27A650U
Size
24 inches (61 cm)
27 inches (68 cm)
Display area
531.36 mm (H) x 298.89 mm (V)
597.6 mm (H) x 336.15 mm (V)
20.9 inches (H) x 11.8 inches (V)
23.5 inches (H) x 13.2 inches (V)
Horizontal
Frequency
30~81 kHz
Vertical
Frequency
56~75 Hz
Display Color
Resolution
C24A650X / C24A650U
16.7M (True 8-bit)
Optimum
resolution
1920 x 1080 @ 60Hz
Maximum
resolution
1920 x 1080 @ 60Hz
Maximum Pixel Clock
165MHz (Analog,HDMI,USB)
Power Supply
This product uses 100 to 240V. Refer to the label at the back of the
product as the standard voltage can vary in different countries.
Signal connectors
D-Sub, HDMI, USB UP port
Dimensions (W x H x D) /
Weight (with the stand)
568.0 X 418.0 X 224.5 mm /
5.4 kg
642.5 X 466.0 X 224.5 mm /
6.3 kg
22.4 X 16.5 X 8.8 inches /
11.9 Ib
25.2 X 17.6 X 8.8 inches /
13.9 Ib
Environme
ntal
considerat
ions
Operating
Temperature : 50˚F ~ 104˚F(10˚C ~ 40˚C)
Humidity : 10 % ~ 80 %, non-condensing
Storage
Temperature : -4˚F ~ 140˚F(-20˚C ~ 60˚C)
Humidity : 5 % ~ 95 %, non-condensing
Plug-and-Play
This monitor can be installed and used with any Plug-and-Play
compatible systems. Two-way data exchange between the monitor
and PC system optimizes the monitor settings. Monitor installation
takes place automatically. However, you can customize the
installation settings if desired.
Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately
1 pixel per million (1ppm) may appear brighter or darker on the panel.
This does not affect product performance.
The above specifications are subject to change without notice to improve quality.
10 Specifications
104
10
Specifications
Class B device (broadcast communications device for home use)
This Class B device designed for home use is registered for EMC requirements and can be used in all
regions.
Recommendation - EU Only
z
Hereby, Samsung Electronics, declares that this Monitor is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
z
The official Declaration of Conformity may be found at http://www.samsung.com, go to Support >
Search Product Support and enter the model name.
z
This equipment may only be used indoors.
z
This equipment may be operated in all EU countries.
z
This product must not be installed in a fixed location, or in a road or railway vehicle.
10 Specifications
105
10
Specifications
10.2 PowerSaver
The power-saving function of this product reduces power consumption by switching off the screen and
changing the color of the power LED if the product is not used for a specified period of time. The power
is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or
move the mouse. Power-savign mode only functions when the product is connected to a PC with a
power-saving function.
PowerSaver
Normal Operation
Power saving
mode
Power off
(Power button)
Power Indicator
On
Blinking
off
Power consumption
(C24A650X / C24A650U)
58 W (Without USB : 43 W)
1.0 W
1.0 W
Power consumption
(C27A650X / C27A650U)
66 W (Without USB : 51 W)
1.0 W
1.0 W
z
The displayed power consumption level can vary in different operating conditions or when settings
are changed.
z
To reduce the power consumption to 0 watts, turn off the power switch on the back of the product
or disconnect the power cable. Be sure to disconnect the power cable when you will not be using
the product for an extended period of time. To reduce the power consumption to 0 watts when the
power switch is not available, disconnect the power cable.
10 Specifications
106
10
Specifications
10.3 Standard Signal Mode Table
z
This product can be set to only one resolution for each screen size to obtain the optimum picture
quality due to the nature of the panel. Therefore, a resolution other than the specified resolution
may degrade the picture quality. To avoid this, it is recommended that you select the optimum
resolution specified for the screen size of your product.
z
Check the frequency when you exchange a CDT monitor (connected to a PC) for an LCD monitor.
If the LCD monitor does not support 85Hz, change the vertical frequency to 60Hz using the CDT
monitor before you exchange it with the LCD monitor.
If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will
automatically be adjusted. If the signal transmitted from the PC does not belong to the standard signal
modes, the screen may be blank with the power LED on. In such a case, change the settings according
to the following table by referring to the graphics card user manual.
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 960
60.000
60.000
108.000
+/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1600 x 1200
75.000
60.000
162.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
+/+
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
z
Horizontal Frequency
The time required to scan a single line from the left to the right side of the screen is called a
horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency.
Horizontal frequency is measured in kHz.
z
Vertical Frequency
Repeating the same picture dozens of times per second allows you to view natural pictures. The
repeat frequency is called "vertical frequency" or "refresh rate" and is indicated in Hz.
10 Specifications
107
Appendix
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
EUROPE
ALBANIA
42 27 5755
-
AUSTRIA
0810 - SAMSUNG
(7267864, € 0.07/min)
http://www.samsung.com
BELGIUM
02-201-24-18
http://www.samsung.com/be
(Dutch)
http://www.samsung.com/be_fr
(French)
BOSNIA
05 133 1999
-
BULGARIA
07001 33 11
http://www.samsung.com
CROATIA
062 SAMSUNG (062 726 7864)
http://www.samsung.com
CZECH
800 - SAMSUNG (800-726786)
http://www.samsung.com
Samsung Zrt., česká organizační složka, Oasis Florenc,
Sokolovská394/17, 180 00, Praha 8
DENMARK
70 70 19 70
http://www.samsung.com
FINLAND
030 - 6227 515
http://www.samsung.com
FRANCE
01 48 63 00 00
http://www.samsung.com
GERMANY
01805 - SAMSUNG
(726-7864,€ 0,14/Min)
http://www.samsung.com
GREECE
2106293100
http://www.samsung.com
HUNGARY
06-80-SAMSUNG (726-7864)
http://www.samsung.com
ITALIA
800-SAMSUNG (726-7864)
http://www.samsung.com
KOSOVO
+381 0113216899
-
LUXEMBURG
261 03 710
http://www.samsung.com
MACEDONIA
023 207 777
-
MONTENEGRO
020 405 888
-
NETHERLANDS
0900 - SAMSUNG
(0900-7267864) (€ 0,10/Min)
http://www.samsung.com
NORWAY
815-56 480
http://www.samsung.com
POLAND
0 801 1SAMSUNG (172678)
022 - 607 - 93 - 33
http://www.samsung.com
Appendix
108
Appendix
EUROPE
PORTUGAL
RUMANIA
80820 - SAMSUNG (726-7864)
08010 SAMSUNG (08010 7267864)
021.206.01.10
http://www.samsung.com
http://www.samsung.com
SERBIA
0700 Samsung (0700 726 7864)
http://www.samsung.com
SLOVAKIA
0800 - SAMSUNG
http://www.samsung.com/sk
(0800-726 786)
SPAIN
902 - 1 - SAMSUNG
(902 172 678)
http://www.samsung.com
SWEDEN
0771 726 7864 (SAMSUNG)
http://www.samsung.com
SWITZERLAND
0848-SAMSUNG
(7267864, CHF 0.08/min)
http://www.samsung.com/ch
U.K
0330 SAMSUNG (7267864)
http://www.samsung.com
EIRE
0818 717100
http://www.samsung.com
LITHUANIA
8-800-77777
http://www.samsung.com
LATVIA
8000-7267
http://www.samsung.com
ESTONIA
800-7267
http://www.samsung.com
http://www.samsung.com/ch_fr
(French)
CIS
RUSSIA
8-800-555-55-55
http://www.samsung.com
GEORGIA
8-800-555-555
-
ARMENIA
0-800-05-555
-
AZERBAIJAN
088-55-55-555
-
KAZAKHSTAN
8-10-800-500-55-500
(GSM: 7799)
http://www.samsung.com
UZBEKISTAN
8-10-800-500-55-500
http://www.samsung.com
KYRGYZSTAN
00-800-500-55-500
http://www.samsung.com
TADJIKISTAN
8-10-800-500-55-500
http://www.samsung.com
UKRAINE
0-800-502-000
http://www.samsung.com/ua
http://www.samsung.com/
ua_ru
BELARUS
810-800-500-55-500
-
MOLDOVA
00-800-500-55-500
-
Appendix
109
Appendix
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with separate
collection systems)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories (e.g. charger, headset, USB cable) should not be disposed of
with other household waste at the end of their working life. To prevent possible harm to
the environment or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to promote the
sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take these items
for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with
other commercial wastes for disposal.
Appendix
110
Appendix
Terminology
OSD(On Screen Display)
On screen display (OSD) allows you to configure on-screen settings to optimize the picture quality as
required. It allows you to change the screen brightness, tint, size and many other settings using
menus displayed on the screen.
HUB
HUB refers to a device that is a common connection point for multiple devices connected over a
network. It is used to connect multiple PCs, video devices, office devices and/or LANs over a single
network.
Dongle
Dongle refers to a device that connects to an input/output port on a PC. It contains a security key or
ID so that only the user that connects the dongle can access a specified application. The dongle on
this product contains data required to use Wireless USB and must be connected to your PC.
Coarse
Coarse refers to the frequency of radio wave vibrations per second. A higher frequency transmits a
larger amount of data and is reflected easier. A lower frequency traverses obstacles more easily and
can travel farther, but it transmits a smaller amount of data. The Coarse menu allows you to manually
adjust the frequency to obtain the optimum picture quality. Adjust Coarse referring to Standard Signal
Mode Table (107page) according to the performance of your product and enjoy improved picture
quality.
Gamma
The Gamma menu adjusts the grey scale that represents middle tones on the screen. Adjusting the
brightness brightens the whole screen, but adjusting Gamma only brightens the medium brightness.
Grey scale
Scale refers to levels of color intensity that show variations of color change from darker areas to
brighter areas on the screen. Changes to the screen brightness are expressed with black and white
variation, and grey scale refers to the medium area between black and white. Changing the grey scale
through Gamma adjustment will change the medium brightness on the screen.
Scanning rate
Scanning rate, or refresh rate, refers to the frequency of screen refreshes. Screen data is transmitted
as it refreshes to display an image, although the refreshing is invisible to the naked eye. The number of
screen refreshes is called scanning rate and is measured in Hz. A scanning rate of 60Hz means that
Appendix
111
Appendix
the screen refreshes 60 times per second. The screen scanning rate depends on the performance of
the graphics cards in your PC and monitor.
Horizontal Frequency
Characters or images displayed on the monitor screen consist of numerous dots (pixels). Pixels are
transmitted in horizontal lines, which are then arranged vertically to create an image. The horizontal
frequency is measured in kHz and represents how many times horizontal lines per second are
transmitted and displayed on the monitor screen. A horizontal frequency of 85 means that the
horizontal lines that make up an image are transmitted 85 000 times per second, and the horizontal
frequency is indicated in 85kHz.
Vertical Frequency
One image is made of numerous horizontal lines. The vertical frequency is measured in Hz and
represents how many images can be created per second by those horizontal lines. A vertical
frequency of 60 means that an image is transmitted 60 times per second. The vertical frequency is
also called "refresh rate" and affects screen flicker.
Resolution
Resolution is the number of horizontal pixels and vertical pixels that form a screen. It represents the
level of display detail.
A higher resolution displays a greater amount of information on the screen and is suitable for
performing multiple tasks at the same time.
E.g. A resolution of 1920 x 1080 consists of 1,920 horizontal pixels (horizontal frequency) and 1,080
vertical lines (vertical resolution).
Plug & Play
The Plug & Play feature allows the automatic exchange of information between a monitor and PC to
produce an optimum display environment.
The monitor uses VESA DDC (international standard) to execute Plug & Play.
Appendix
112
Index
A
F
About "HUB Monitor" 32
Fine 65
Appendix 108
Auto Source 92
G
Gamma 71
B
General 104
Before Connecting 48
Green 68
Blue 69
Brightness 61
H
HUB 75
C
Checking the Contents 19
Cleaning 4
Coarse 64
Color Tone 70
I
Image Size 72
INFORMATION 99
Installing the Product 26
Configuring Brightness in the Startup Screen
99
Configuring the HUB Monitor IP 43
K
Connecting and Using a PC 49
Key Repeat Time 94
Connecting Headphones 56
Connecting the Product to a PC to Use "HUB
Monitor" 35
L
Contact SAMSUNG WORLDWIDE 108
Languagey 90
Contrast 62
Copyright 2
M
Correct Disposal of This Product (Waste
Electrical & Electronic Equipment) 110
MAGIC 58
Correct posture to use the product 13
D
Display Time 93
MagicRotation Auto 31
Menu Transparency 89
N
Notice before your use of Wireless USB or
USB Mode 47
E
ECO 81
O
Off Timer On/Off 96
Off Timer Setting 97
Index
113
Index
P
Parts 22
PC/AV Mode 91
PowerSaver 106
Q
Q & A 103
R
Red 67
Requirements Before Contacting Samsung
Customer Service Center 100
Reset 98
Response Time 66
S
Safety Precautions 5
Sharpness 63
Software Installation for Using "HUB Monitor"
33
Standard Signal Mode Table 107
T
Terminology 111
U
Utilizing "HUB Monitor" 40
Index
114

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • 61 cm (24")
  • Full HD 1920 x 1080 pixels 16:9
  • 8 ms 250 cd/m² 3000:1
  • 58 W

Related manuals

Download PDF

advertisement