Microwave
Technical Bulletin
Sharp Electronics Corporation
Services and Support Group
1300 Naperville Drive
Romeoville, IL 60446
Number: MW-174
Date: July 2003
Model(s): R-1850/51, R1855A, R1870/71/72
SUBJECT: Service manual correction.
Please see the chart below for service manual correction.
R-1850, R1851
Ref #
4-21
PART NUMBER
INCORRECT
CORRECT
NFANPB004MRK0 NFANPB004MRE0B
DESCRIPTION
Fan Blade
PRICE
CODE
AC
R-1870, R1871, R1872
Ref #
4-21
PART NUMBER
INCORRECT
NFANPB005MRK0
CORRECT
NFANPB005MRE0
DESCRIPTION
Fan Blade
PRICE
CODE
AC
R-1855A
Ref #
4-20
SVC-142
PART NUMBER
INCORRECT
NFANPB005MRK0
CORRECT
NFANPB005MRE0
Bulletin # MW-174
DESCRIPTION
Fan Blade
PRICE
CODE
AC
Page 1 of 1
Microwave
Technical Bulletin
Sharp Electronics Corporation
Services and Support Group
1300 Naperville Drive
Romeoville, IL 60446
Number: MW-186
Date: December 2003
Model(s): R1200 / R1201 / R1210 / R1211 / R1214 / R1405 / R1406 / R1500 / R1501 / R1502 /
R1505 / R1506 / R1510 / R1511 / R1512 / R1514 / R1600 / R1601 / R1602 / R1610 / R1611 /
R1612 / R1750 / R1751 / R1752 / R1754 / R1850 / R1851 / R1852 / R1850A / R1851A / R1852A /
R1855A / R1870 / R1871 / R1872 / R1874 / R1875
SUBJECT: Part substitution
The old part number is no longer available. Please use the new part number listed
below.
Description
Old Part
Number
New Part
Number
Inter
change
ability
Oven Lamp
RLMPTA068WRE0
RLMPTA086WRZZ
C
<Interchange>
A: Interchangeable
B: Current type can be use in place of new type. New type
cannot be used on place of current type.
SVC-148
C: Current type cannot be used in place of new type.
New type can be used in place of current type.
D: Not interchangeable
Bulletin # MW-186
Page 1 of 1
R-1855A
SERVICE MANUAL
S99M138R1855E
OVER THE RANGE
MICROWAVE OVEN
MODEL
R-1855A
In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.
This model for the US and Canada markets, Please refer to the appropriate pages for service information.
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICE TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY .................. INSIDE FRONT COVER
BEFORE SERVICING .......................................................................................................................................... 1
MICROWAVE MEASUREMENT PROCEDURE .................................................................................................. 2
FOREWORD ........................................................................................................................................................ 4
PRODUCT SPECIFICATIONS ............................................................................................................................. 5
GENERAL INFORMATION ................................................................................................................................. 5
OPERATION ........................................................................................................................................................ 7
TROUBLESHOOTING GUIDE ............................................................................................................................ 17
TEST PROCEDURE ........................................................................................................................................... 20
TOUCH CONTROL PANEL ................................................................................................................................31
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE ................................................................ 37
PICTORIAL DIAGRAM .......................................................................................................................................46
CONTROL PANEL CIRCUIT ..............................................................................................................................47
PRINTED WIRING BOARD ................................................................................................................................48
PARTS LIST ........................................................................................................................................................49
PACKING AND ACCESSORIES ......................................................................................................................... 55
This document has been published to be used for after sales service only. The contents are subject to
change without notice.
SHARP ELECTRONICS CORPORATION
Service Headquarters: Sharp Plaza, Mahwah, New Jersey, 07430-2135
OR:
SHARP CORPORATION
SHARP ELECTRONICS OF CANADA LTD.
Head Office: 335 Britannia Road East, Mississauga, Ontario L4Z 1W9
(905) 890-2100
R-1855A
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or
other microwave source, and make repairs as necessary: (1) interlock operation (2) proper door
closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening
of hinges and latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave
generating compartments, check the magnetron, wave guide or transmission line, and cavity for
proper alignment, integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures
described in this manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
(RD2110U)
BEFORE SERVICING(USA)
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS
CORPORATION immediately @1-800-237-4277.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration's Center
for Devices and Radiological Health immediately.
Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit found
with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit
until the oven has been brought into compliance.
(RD2110U)
BEFORE SERVICING(CANADA)
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS OF
CANADA LTD. immediately.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact SHARP ELECTRONICS OF CANADA LTD. and NHW, CANADA immediately.
Service personnel should inform SHARP ELECTRONICS OF CANADA LTD. of any certified unit found
with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit
until the oven has been brought into compliance.
(RD8100U)
R-1855A
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly fatal,
electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
Before Servicing
1. Disconnect the power supply cord
remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
, and then
WARNING: RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
After repairing
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for
60 seconds and then short-circuit the connection of the
high-voltage capacitor (that is the connecting lead of the
high-voltage rectifier) against the chassis with the use of
an insulated screwdriver.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out Before Servicing procedure and reexamine the connections to the component being tested.
Whenever troubleshooting is performed the power supply
must be disconnected. It may in, some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that these leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and microwave leakage test should be carried out.
When the testing is completed,
1. Disconnect the power supply cord, and then remove
1
R-1855A
MICROWAVE MEASUREMENT PROCEDURE (USA)
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches Primary interlock relay and door sensing switch shall prevent microwave radiation emission
in excess of the requirement as above mentioned, secondary interlock switch shall prevent microwave radiation
emission in excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard
for microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5OC (68OF) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2in.)
and made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is
completed, replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement)
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on
the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the
metal has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2,
and that the secondary interlock switch does turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
R-1855A
MICROWAVE MEASUREMENT PROCEDURE (CANADA)
After adjustment of the door switches are completed individually or collectively, switch test and microwave leakage test must
be performed with survey instrument and test result must be confirmed to meet the requirement of the performance standard
for microwave ovens as undermentioned.
A. Requirements:
Every microwave oven shall function in such a manner that when the oven is fully assembled and operating with it's service
controls and user controls adjusted to yield the maximum output, the leakage radiation, at all points at least 5 cm. from the
external surface of the oven, does not exceed:
1) 1.0mW/cm2 with the test load of 275 ± 15 ml of water at an initial temperature 20 ±5oC.
2) 5.0mW/cm2 when the outer enclosure is removed with a test load of 275 ± 15 ml of water at an initial temperature 20±5oC.
3) 5.0mW/cm2 without a test load.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by CSA and NHW performance standard
for microwave ovens must be used for testing recommended instruments are , NARDA 8100 and NARDA 8200.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml of tap water initially at 20±5oC in the center of the oven cavity.
The water container shall be a low form of 600 ml beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and made
of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode, Close the door and select a cook cycle of several minutes. If the water
begins to boil before the survey is completed, replace it with 275 ml of cool water.
C. Leakage test with enclosure installed :
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 2.5 cm/sec. along the gap, watching for the maximum indication on the meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2, and
that the secondary interlock switch does turn the oven OFF before any door movement.
C. Leakage test without enclosure:
1) Remove the enclosure (cabinet).
2) Grasp the probe of the survey instrument and hold it perpendicular to all mechanical and electric parts of the oven that is
accessible to the user of the oven including, but not limited to, the waveguide, cavity seams, magnetron gap between the
door and the body of the oven.
3) Move the probe slowly, not faster than 2.5 cm/sec. along the gap, watching for the maximum indication on the meter.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is under 5mW/cm2.
CAUTION: Special attention should be given to avoid electrical shock because HIGH VOLTAGE is generated during this test
No Load test
1) Operate the oven without a load and measure the leakage by the same method as the above test procedure " Leakage
test with enclosure installed"
2) Make sure that the highest leakage should not exceed 5mW/cm2.
NOTE: After servicing, record data on service invoice and microwave leakage report.
3
R-1855A
SERVICE MANUAL
OVER THE RANGE
PRODUCT DESCRIPTION
MICROWAVE OVEN
R-1855A
GENERAL INFORMATION
FOREWORD
This Manual has been prepared to provide Sharp Electronics Corp.
Service Personnel with Operation and Service Information for the
SHARP OVER THE RANGE MICROWAVE OVEN, R-1855A.
It is recommended that service personnel carefully study the entire
text of this manual so that they will be qualified to render satisfactory
customer service.
Check the interlock switches and the door seal carefully. Special
attention should be given to avoid electrical shock and microwave
radiation hazard.
OPERATION
TROUBLESHOOTING GUIDE AND
TEST PROCEDURE
TOUCH CONTROL PANEL
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is no other visible damage with the oven.
COMPONENT REPLACEMENT AND
ADJUSTMENT PROCEDURE
Servicing and repair work must be carried out only by trained service
personnel.
WIRING DIAGRAMS
DANGER
Certain initial parts are intentionally not grounded and
present a risk of electrical shock only during servicing.
Service personnel - Do not contact the following parts while
the appliance is energized;
High Voltage Capacitor, Power Transformer, Magnetron,
High Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more
than 250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “∆” on parts list may cause undue microwave
exposure, by themselves, or when they are damaged, loosened
or removed.
USA MODEL
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH,
NEW JERSEY 07430-2135
CANADIAN MODEL
OSAKA, JAPAN
4
PARTS LIST
R-1855A
SPECIFICATION
ITEM
DESCRIPTION
Power Requirements
120 Volts / 13.2 Amperes (Microwave), 13.2 Amperes (Convection)
60 Hertz
Single phase, 3 wire grounded
Power Output
850 watts (IEC-705 TEST PROCEDURE)
Operating frequency of 2450MHz
Convection Power Output
1400 watts
Case Dimensions
Width 29-15/16"
Height 16-11/32"
Depth 15- 9/32"
Cooking Cavity Dimensions
Width 17-1/8"
Height 8-1/16"
Depth 13-13/16"
1.1 Cubic Feet
Hood lamp
2 bulbs, 30W x 2, Incandescent light bulbs
Hood fan
Horizontal discharge 230 C.F.M. , Vertical discharge 240 C.F.M. ,
Control Complement
Touch Control System
Clock ( 1:00 - 12:59 )
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI ................................................ Full power throughout the cooking time
P-90 ................................................................... approx. 90% of Full Power
P-80 ................................................................... approx. 80% of Full Power
P-70 ................................................................... approx. 70% of Full Power
P-60 ................................................................... approx. 60% of Full Power
P-50 ................................................................... approx. 50% of Full Power
P-40 .................................................................... approx. 40% of Full Power
P-30 .................................................................... approx. 30% of Full Power
P-20 ................................................................... approx. 20% of Full Power
P-10 ..................................................................... approx. 10% of Full Powe
P-0 .................................................... No power throughout the cooking time
CUSTOM HELP pad, SENSOR COOK pad, COMPU BROIL pad, COMPU ROAST pad
COMPU BAKE pad, SENSOR REHEAT pad, MINUTE PLUS pad, POPCORN pad
COMPU DEFROST pad, CONVECTION pad, REHEAT pad, LOW MIX/BAKE pad
HIGH MIX/ROAST pad, BROIL pad, SLOW COOK pad, KITCHEN TIMER pad
Number and temperature selection pads, CLOCK pad, KEEP WARM pad
TURNTABLE ON / OFF pad, POWER LEVEL pad, STOP/CLEAR pad,
START / TOUCH ON pad
Oven Cavity Light
Yes 30W x 1 Incandescent light bulb
Safety Standard
UL Listed
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
Canadian Standards Association.
Department of National Health and Welfare CANADA, Industry CANADA.
Approx. 71 lbs.
Weight
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed
and grounded in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the
electric current.
WARNING:
Improper use of the grounding plug can result in a risk of electric shock.
5
R-1855A
Electrical Requirements
The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE
GROUNDING PIN FROM THE PLUG.
The power supply cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp. or more branch circuit, using
a grounded receptacle. The receptacle should be located inside the cabinet directly above the Microwave Oven/Hood
system mounting location.
Grounded
Receptacle Box
3-Pronged Plug
Grounding Pin
3-Pronged Receptacle
OVEN DIAGRAM
12
1
11
10
3
4
5
13
9
8
6
2
7
6
17
14
15
16
MIX CONV
DEFROST
SENSOR
TURNTABLE ON OFF
1.
2.
3.
4.
5.
Oven door with see-through window.
Door hinges.
Stirrer cover.
Turntable motor shaft.
Oven lamp.
It will light when oven is operating or door is open.
6. Door latches.
The oven will not operate unless the door is securely closed.
7. One touch door open button.
Push to open door.
8. FAN-HI/LO button.
Push for High/Low/Off.
9. Light button.
Push for On/Off
10. Auto-Touch control panel.
11. Time display: Digital display, 99 minutes 99 seconds.
12. Ventilation openings.
13. Light Cover.
14. Grease filters.
15. Removable turntable.
The turntable will rotate clockwise or counterclockwise.
Only remove for cleaning.
16. Removable turntable support.
17. Plug
COOK LBS
OZ
KG HELP
CUSTOM
HELP
INTERACTIVE COOKING SYSTEM
SENSOR
REHEAT
MINUTE
PLUS
COMPU
POPCORN DEFROST
CONVEC
REHEAT
LOW MIX HIGH MIX
BAKE
ROAST
BROIL
1
100˚F
6
350˚F
CONTROL PANEL
6
SLOW
COOK
2
150˚F
7
375˚F
1
2
3
4
5
6
7
8
Baked potatoes
Frozen vegetables
Fresh veg-soft
Fresh veg-hard
Frozen entrees
Hot dogs
Bacon
Fish, seafood
SENSOR
COOK
1
2
3
4
Hamburgers
Chicken pieces
Steaks
Fish steaks
COMPU
BROIL
1
2
3
4
Chicken
Turkey
Turkey breast
Pork
COMPU
ROAST
1
2
3
4
Cake
Brownies
Muffins
French fries
COMPU
BAKE
3
275˚F
8
400˚F
4
300˚F
9
425˚F
KITCHEN
TIMER
CLOCK
KEEP
WARM
TURNTABLE
ON / OFF
POWER
LEVEL
STOP
CLEAR
5
325˚F
0
450˚F
START
TOUCH ON
R-1855A
OPERATION
DESCRIPTION OF OPERATING SEQUENCE
(1) When the door opens from a closed position, the
primary interlock relay, door sensing switch,
secondary interlock switch and third door switch
open their contacts, and then the monitor switch
contacts close.
(2) When the door is closed from the open position, the
monitor switch contacts first open, and then the
contacts of the secondary interlock switch and third
door switch close.
If the secondary interlock switch, third door switch and door
sensing switch fail with their contacts closed when the door
is opened, the closing of the monitor switch contacts will
form a short circuit through the monitor fuse, third door
switch, secondary interlock switch and primary interlock
relay, causing the monitor fuse to blow.
The following is a description of component functions during
oven operation.
OFF CONDITION
Closing the door activates the door sensing switch and
secondary interlock switch. (In this condition, the monitor
switch contacts are opened.)
When oven is plugged in, 120 volts A.C. is supplied to the
control unit. (Figure O-1).
1. The display will show
,
,
,
,
,
,
,
and
.
To set any program or set the clock, you must first touch
the STOP/CLEAR pad. The display will clear, and " : "
will appear.
POWER LEVEL P-0 TO P-90 COOKING
COOKING CONDITION
When Variable Cooking Power is programmed, the 120
volts A.C. is supplied to the power transformer intermittently through the contacts of relay (RY2) which is operated
by the control unit within an interval second time base.
Microwave power operation is as follows:
Program desired cooking time touching the NUMBER pads.
When the START pad is touched, the following operations
occur:
1. The contacts of relays are closed and components
connected to the relays are turned on as follows.
(For details, refer to Figure O-2)
RELAY
RY1
RY2
RY4
RY5
VARI-MODE
ON TIME
Power 10(P-HI)
32 sec.
(100% power)
Power 9(P-90)
30 sec.
(approx. 90% power)
Power 8(P-80)
26 sec.
(approx. 80% power)
Power 7(P-70)
24 sec.
(approx. 70% power)
Power 6(P-60)
22 sec.
(approx. 60% power)
Power 5(P-50)
18 sec.
(approx. 50% power)
Power 4(P-40)
16 sec.
(approx. 40% power)
Power 3(P-30)
12 sec.
(approx. 30% power)
Power 2(P-20)
8 sec.
(approx. 20% power)
Power 1(P-10)
6 sec.
(approx. 10% power)
Power 0(P-0)
0 sec.
(0% power)
CONNECTED COMPONENTS
Oven lamp
Power transformer/ Stirrer motor
Turntable motor
Fan motor
2. 120 volts A.C. is supplied to the primary winding of the
power transformer and is converted to about 3.3 volts
A.C. output on the filament winding, and approximately
2000 volts A.C. on the high voltage winding.
3. The filament winding voltage heats the magnetron filament
and the H.V. winding voltage is sent to a voltage doubler
circuit.
4. The microwave energy produced by the magnetron is
channelled through the waveguide into the cavity feedbox, and then into the cavity where the food is placed to
be cooked.
5. Upon completion of the cooking time, the power
transformer, oven lamp, etc. are turned off, and the
generation of microwave energy is stopped. The oven
will revert to the OFF condition.
6. When the door is opened during a cook cycle, monitor
switch, door sensing switch, secondary interlock switch
and third door switch and primary interlock relay are
activated with the following results. The circuits to the
stirrer motor, the cooling fan motor, the turntable motor,
and the high voltage components are de-energized, and
the digital read-out displays the time still remaining in the
cook cycle when the door was opened.
7. The monitor switch is electrically monitoring the operation
of the secondary interlock switch, third door switch and
door sensing switch is mechanically associated with the
door so that it will function in the following sequence.
OFF TIME
0 sec.
2 sec.
6 sec.
8 sec.
10 sec.
14 sec.
16 sec.
20 sec.
24 sec.
26 sec.
32 sec.
Note: The ON/OFF time ratio does not correspond with the
percentage of microwave power, because approx.
2 seconds are needed for heating of the magnetron
filament.
CONVECTION COOKING CONDITION
PREHEATING CONDITION
Program desired convection temperature by touching the
PREHEAT pad and the temperature pad.
7
R-1855A
touched, the following operations occur:
1. The numbers on the digital read-out start to count down
to zero.
2. The shut-off relays (RY1, RY4, RY5 and RY7) are
energized, turning on the oven lamp, turntable motor,
cooling fan motor and convection motor.
3. The shut-off relay (RY6) is energized.
The damper plate is closed from the open position.
4. The heater relay (RY3) is energized, applying the main
supply voltage to the heating element.
5. Now, the oven is in the convection cooking condition.
6. When the oven temperature reaches the selected
temperature, the following operations occur:
6-1. The power supply voltage is alternated to the
heating element and power transformer.
6-2. The heating element operates through the heater
relay (RY3) contacts and the power transformer
operates through the primary interlock relay (RY2)
contacts.
6-3. These are operated by the control unit to supply
alternately within a 32 second time base, convection
heat and microwave energy.
When the START pad is touched, the following operations
occur:
1. The coil of shut-off relays (RY1, RY4, RY5 and RY7) are
energized, the oven lamp, turntable motor, cooling fan
motor and convection motor are turned on.
2. The coil of relay (RY6) is energized by the control unit.
The damper is moved to the closed position, opening the
damper switch contacts. The opening of the damper
switch contacts sends a signal to the LSI on the control
unit de-energizing the relay (RY6) and opening the
circuit to the damper motor.
3. The coil of heater relay (RY3) is energized by the control
unit and the main supply voltage is applied to the heating
element.
4. When the oven temperature reaches the selected preheat
temperature, the following operations occur:
4-1 The heater relay is de-energized by the control unit
temperature circuit and thermistor, opening the
circuit to the heating element.
4-2. The oven will continue to function for 30 minutes,
turning the heater on and off, as needed to maintain
the selected preheat temperature. The oven will
shutdown completely after 30 minutes
The relationship between the convection and microwave
power operations are as follows.
Note: The ON and OFF time ratio does not correspond
with the percentage of microwave power, because
approx. 2 seconds are needed for heating of the
magnetron filament.
CONVECTION COOKING CONDITION
When the preheat temperature is reached, a beep signal will
sound indicating that the holding temperature has been
reached in the oven cavity. Open the door and place the food
to be cooked in the oven.
Program convection temperature and desired cooking time
by touching the CONVECTION pad, Temperature pad and
NUMBER pad.
When the START pad is touched, the following operations
occur:
1. The numbers on the digital read-out start to count down
to zero.
2. The oven lamp, turntable motor, cooling fan motor and
convection motor are energized.
3. Heater relay (RY3) is energized (if the cavity temperature
is lower than the selected temperature) and the main
supply voltage is applied to the heating element to return
to the selected cooking temperature.
4. Upon completion of the cooking time, the audible signal
will sound, and oven lamp, turntable motor, cooling fan
motor and convection motor are de-energized. At the
end of the convection cycle, if the oven temperature is
above 275OF, the circuit to RY5 will be maintained (by
the thermistor circuit) to continue operation of the
cooling fan motor until the temperature drops below
245OF, at which time the relay will be de-energized,
turning off the fan motor. Relay RY7 will however, open
as soon as the convection cycle has ended, turning off
the convection motor.
5. At the end of the convection cook cycle, shut-off relay
(RY6) is energized turning on the damper motor. The
damper is returned to the open position, closing the
damper switch contacts which send a signal to the
control unit, de-energizing shut-off relay (RY6).
6 SEC.
26 SEC.
ON
MICROWAVE POWER
= APPROX. 10%
(MICRO.)
OFF
CONVECTION
TEMPERATURE
= 325˚F (165˚C)
(CONVEC.)
LOW MIX
BAKE
12 SEC.
20 SEC.
ON
(MICRO.)
OFF
MICROWAVE POWER
= APPROX. 30%
ON
(CONVEC.)
OFF
32 SEC.
CONVECTION
TEMPERATURE
325˚F (165˚C)
HIGH MIX
ROAST
Note:
During alternate Microwave/Convection operation,
the convection heater is energized only if the cavity
temperature drops below the set temperature.
SENSOR COOKING CONDITION
Using the SENSOR COOK, SENSOR REHEAT or POPCORN function, the foods are cooked or defrosted without
figuring time, power level or quantity. When the oven senses
enough steam from the food, it relays the information to its
microprocessor which will calculate the remaining cooking
time and power level needed for best results.
When the food is cooked, water vapor is developed. The
sensor “senses” the vapor and its resistance increases
gradually. When the resistance reaches the value set
according to the menu, supplementary cooking is started.
AUTOMATIC MIX COOKING CONDITION
Touch the LOW MIX/BAKE or HIGH MIX/ROAST pad. The
LOW MIX/BAKE pad is preprogrammed for 325OF with 10%
microwave power, while the HIGH MIX/ROAST pad is
preprogrammed for 325OF with 30% microwave power.
Program desired cooking time. When the START pad is
8
R-1855A
The time of supplementary cooking is determined by
experiment with each food category and inputted into the
LSI.
An example of how sensor works:
automatically compute the oven temperature, microwave
power and cooking time for broiling, roasting and baking. Set
the desired program by touching one of the COMPU BROIL,
COMPU ROAST or COMPU BAKE pad, and number pad.
Enter the weight by touching the Number pads. When the
START pad is touched, the following operations occur:
1. The COOK indicator will light and the CONV or MIX
indicator will light.
2. The cooking time will appear on the display and start
counting down to zero. The cooking time is adjusted
automatically according to the weight of the food.
3. The shut-off relays (RY1, RY4, RY5 and RY7) are
energized, turning on the oven lamp, turntable motor,
cooling fan motor and convection motor. The power
supply voltage is applied to the heating element.
4. Now, the oven is in the convection cooking mode or
Automatic Mix Cooking condition.
5. When the oven temperature has reached the
programmed convection temperature, the oven goes
into the programmed cooking mode.
6. At the end of the cooking cycle, the damper is returned
to the open position and the oven will go to the off
condition. The cooling fan will remain on until the oven
has cooled.
1. Potatoes at room temperature. Vapor is emitted very
MIC
slowly.
RO
WA
VE
2. Heat potatoes. Moisture and humidity is emitted rapidly.
You can smell the aroma as it cooks.
AH SENSOR
MIC
RO
WA
VE
COMPU DEFROST COOKING
The COMPU DEFROST key is a special function key to
defrost meats and poultry faster and better. COMPU
DEFROST automatically defrosts roast beef, etc.. When
the COMPU DEFROST is selected and the food weight is
entered by using the COMPU DEFROST pad, the oven will
cook according to the special cooking sequence.
3. Sensor detects moisture and humidity and calculates
cooking time and variable power.
Cooking Sequence.
1. Touch SENSOR COOK, SENSOR REHEAT or
POPCORN pad. When Sensor Cook is touched, to
choose menu the number pad should be touched.
NOTE: The oven should not be operated on SENSOR
COOK, SENSOR REHEAT or POPCORN
immediately after plugging in the unit. Wait five
minutes before cooking on SENSOR COOK,
SENSOR REHEAT or POPCORN.
2. The coil of shut-off relays (RY1, RY4 and RY5) are
energized, the oven lamp, turntable motor and cooling
fan motor are turned on, but the power transformer is not
turned on.
3. After about 32 seconds, the cook relay (RY2) is energized.
The power transformer is turned on, microwave energy
is produced and first stage is started.
The 32 seconds is the cooling time required to remove
any vapor from the oven cavity and sensor.
NOTE: During this first stage, do not open the door or touch
STOP/CLEAR pad.
4. When the sensor detects the vapor emitted from the
food, the display switches over to the remaining cooking
time and the timer counts down to zero.
At this time, the door may be opened to stir food, turn it
or season, etc.
5. When the timer reaches zero, an audible signal sounds.
The shut-off relay and cook relay are de-energized and
the power transformer, oven lamp, etc. are turned off.
6. Opening the door or touching the STOP/CLEAR pad, the
time of day will reappear on the display and the oven will
revert to an OFF condition.
FIRE SENSING FEATURE (MICROWAVE MODE)
This model incorporates a sensing feature which will stop
the oven's operation if there is a fire in the oven cavity during
microwave cooking.
This is accomplished by the LSI repeatedly measuring the
voltage across the temperature measurement circuit (thermistor) during it's 32-seconds time base comparing the
obtained voltage measurements. If the most recent voltage
measured is 100mV greater than the previous voltage
measured, the LSI judges it as a fire in the oven cavity and
switches off the relays to the power transformer and fan
motor. The LSI also stops counting down and closes the
damper plate so that no fresh air will enter the oven cavity.
Please refer to the following section for a more detailed
description.
Operation
The following operation will start 4 minutes after the start
pad is touched. Please refer to the timing diagrams below.
1. The thermistor operates within a 32-seconds time base
and it is energized for three (3) seconds and off for 29
seconds. Two (2) seconds after the thermistor is
energized, the voltage across the temperature
measurement circuit is sampled by the LSI and twenty
one (21) seconds after the thermistor is cut off the LSI
turns on the convection motor for six (6) seconds.
2. The above procedure is repeated. If the difference
between the first voltage measured (in step 1) and the
voltage measured when the procedure is repeated (step
2) is greater than 100mV the LSI makes the judgment
that there is a fire in the oven cavity and will switch off
COMPU BROIL, COMPU ROAST, COMPU BAKE
COMPU BROIL, COMPU ROAST and COMPU BAKE will
9
R-1855A
3. RE-CIRCULATION (INSIDE VENTING)
The air handing is same as VERTICAL VENTING except
that the final air discharge is directed horizontally
through the upper front of the oven into the kitchen. IN
this case, the accessory charcoal filter lit RK-220 must
be provided to filter the air before it leaves the oven.
the relays to the power transformer and fan motor. The
LSI also stops counting down and closes the damper
door so that no fresh air will enter the oven cavity.
3. Once the fire sensor feature has shut the unit down, the
programmed cooking cycle may be resumed by pressing
the "START" pad or the unit may be reset by pressing the
"CLEAR" pad.
: AIR FLOW
IMPORTANT:
During sensor cooking operation, the fire sensing
operation sequence will not begin until the AH sensor
has detected vapors and initiated a sensor cooking
cycle. This is because the operation of the convection
fan would interfere with the AH sensor's vapor detection.
0 23
24
30 32 (sec.)
HOOD FAN MOTOR
HOOD
INTAKE
DUCT R
64 (sec.)
6 sec.
CONVECTION
MOTOR
ON
OFF
3 sec.
THERMISTOR
ON
OFF
ON
Sensing
Voltage OFF
Sensing the voltage across the temperature measurement circuit.
VENTILATION METHODS HOT AIR EXHAUST
1. VERTICAL VENTING
For this venting method, hot air rising from the
conventional range below is drawn in by the hood fan
motor through the grease filters at the right and left sides
of the base cover, up through the right and left side intake
ducts, then discharged vertically at rear center top of the
oven, into the customer's vent system.
: AIR FLOW
TO DUCT
TO DUCT
HOOD FAN MOTOR
HOOD
INTAKE
DUCT R
GREASE
FILTER
2. HORIZONTAL VENTING
The air handing is same as VERTICAL VENTING except
that the final air discharge is directed horizontally out
from the top rear of the oven into the customer's vent
system.
: AIR FLOW
HOOD FAN MOTOR
HOOD
INTAKE
DUCT R
HOOD EXHAUST
LOUVER
TO DUCT
GREASE
FILTER
10
CHARCOAL
FILTER
R-1855A
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CLOCK APPEARS ON DISPLAY.
RY5
RY7
C1
BRN
RY2
HOOD
LAMP
HL
HL
E6 E3
BLK
WHT-WHT
WHT
WHT
BRN
STIRRER
MOTOR
POWER
TRANSFORMER
E4
F1 F2
F3
COM
RY1
WHT WHT
GRY
GRY
CONTROL UNIT
HIGH
VOLTAGE
CAPACITOR
0.9 F
HIGH
VOLTAGE
RECTIFIER
AH SENSOR
RED
YEL
GRY BLU
NOISE
FILTER
BLK
E2 E5
STM
RED
E1
DAMPER
SWITCH
RY1
RY3
BRN
BLK
N.O.
RY3
THERMISTOR
GRN
COM
RY3
PNK
COM
RY2
PPL
RED
BRN PPL
BRN WHT
N.O.
B7 RY1
RY4
BLK
ORG
BLK
ORG
GRY
WHT
BLK
WHT
B1
MONITOR
SWITCH
OVEN
OL LAMP
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
WHT
A3
B3
HEATING
ELEMENT
PRIMARY INTERLOCK
RELAY
PNK
RED
YEL
A1
B5
RY6
RY8
HOOD
MOTOR
PPL
BLU
C5
RY10
BLU
C7
PPL HOOD
CAPACITOR
BLK
ORG
ORG
NOISE
RESISTOR
WHT
CONVECTION
MOTOR
CM
FM
FAN
MOTOR
DM
TTM
TURN
DAMPER
TABLE
MOTOR
MOTOR
C9
ORG
ORG BLK
A5
RY9
GND
BLK
GRN
HOOD FAN
THERMAL
CUT OUTS
SECONDARY
INTERLOCK
SWITCH
MAGNETRON
WHT
BLK
BRN C3
PNK
BLK
RED
120VAC
60Hz
MAGNETRON
TEMPERATURE
FUSE
FUSE
20A
RED
ORG
RED
Note:
When servicing units between serial number 111112 and 112161, use the
schematics in Figure O-1 through O-4.
N.O.
RY2
Ref 2-6(TMAPCB058MRR0)
Figure O-1. Oven Schematic - Off Condition
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. COOKING TIME PROGRAMMED.
3. START PAD TOUCHED.
RY4
RY7
E2 E5
E6 E3
E4
RY3
RY2
F1 F2
F3
AH SENSOR
COM
RY1
WHT WHT
GRY
GRY
RED
YEL
GRY BLU
WHT-WHT
POWER
TRANSFORMER
RY1
C1
CONTROL UNIT
WHT
STM
STIRRER
MOTOR
WHT
BLK
BRN
DAMPER
SWITCH
RED
E1
BLK
GRN
N.O.
RY3
PNK
PPL
RED
COM
RY3
HOOD
LAMP
HL
HL
NOISE
FILTER
BLK
BLK
ORG
COM
RY2
BRN PPL
N.O.
B7 RY1
BRN WHT
GRY
WHT
BLK
WHT
PPL
B1
THERMISTOR
N.O.
RY2
Ref 2-6(TMAPCB058MRR0)
Figure O-2. Oven Schematic - Microwave Cooking Condition
11
WHT
A3
PNK
A1
RY5
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
MONITOR
SWITCH
OVEN
OL LAMP
PRIMARY INTERLOCK
RELAY
BRN
HOOD
MOTOR
RY6
B3
HEATING
ELEMENT
BRN
RED
RY8
B5
ORG
BLK
ORG
ORG
CONVECTION
MOTOR
CM
ORG
BLU
C5
RY10
BLU
C7
PPL HOOD
CAPACITOR
YEL
BLK
NOISE
RESISTOR
WHT
ORG BLK
A5
FM
FAN
MOTOR
DM
TTM
TURN
DAMPER
TABLE
MOTOR
MOTOR
C9
RY9
GND
BLK
GRN
HOOD FAN
THERMAL
CUT OUTS
SECONDARY
INTERLOCK
SWITCH
HIGH
VOLTAGE
CAPACITOR
0.9 F
HIGH
VOLTAGE
RECTIFIER
MAGNETRON
WHT
BLK
BRN C3
PNK
BLK
RED
120VAC
60Hz
MAGNETRON
TEMPERATURE
FUSE
FUSE
20A
RED
ORG
RED
R-1855A
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CONVECTION PAD TOUCHED.
3. DESIRED TEMP. TOUCHED.
4. START PAD TOUCHED.
RY5
RY4
RY7
E6 E3
BLK
WHT-WHT
WHT
WHT
BLK
BRN
BLK
E2 E5
STM
STIRRER
MOTOR
POWER
TRANSFORMER
RED
E1
E4
RY1
C1
BRN
RY2
HOOD
LAMP
HL
HL
F1 F2
F3
HIGH
VOLTAGE
CAPACITOR
0.9 F
HIGH
VOLTAGE
RECTIFIER
CONTROL UNIT
COM
RY1
WHT WHT
GRY
GRY
AH SENSOR
RED
YEL
GRY BLU
NOISE
FILTER
DAMPER
SWITCH
THERMISTOR
GRN
N.O.
RY3
PNK
COM
RY3
PPL
RED
BRN PPL
COM
RY2
RY3
BRN
BLK
ORG
N.O.
B7 RY1
BRN WHT
GRY
WHT
BLK
WHT
B1
MONITOR
SWITCH
OVEN
OL LAMP
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
WHT
A3
B3
HEATING
ELEMENT
PRIMARY INTERLOCK
RELAY
PNK
RED
YEL
A1
B5
RY6
RY8
HOOD
MOTOR
PPL
BLU
C5
RY10
BLU
C7
PPL HOOD
CAPACITOR
BLK
BLK
ORG
ORG
ORG
NOISE
RESISTOR
WHT
CONVECTION
MOTOR
CM
FM
FAN
MOTOR
DM
TTM
TURN
DAMPER
TABLE
MOTOR
MOTOR
C9
ORG
ORG BLK
A5
RY9
GND
BLK
GRN
HOOD FAN
THERMAL
CUT OUTS
SECONDARY
INTERLOCK
SWITCH
MAGNETRON
WHT
BLK
BRN C3
PNK
BLK
RED
120VAC
60Hz
MAGNETRON
TEMPERATURE
FUSE
FUSE
20A
RED
ORG
RED
N.O.
RY2
Ref 2-6(TMAPCB058MRR0)
Figure O-3. Oven Schematic - Convection Cooking Condition (CONVEC, PREHEAT, BROIL, SLOW COOK)
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. MIX COOKING PAD TOUCHED.
3. DESIRED TEMP. TOUCHED.
4. COOKING TIME PROGRAMMED.
5. START PAD TOUCHED.
RY7
E6 E3
E4
RY3
RY2
F1 F2
F3
COM
RY1
WHT WHT
GRY
RED
YEL
GRY BLU
GRY
AH SENSOR
N.O.
RY2
Ref 2-6(TMAPCB058MRR0)
Figure O-4. Oven Schematic - Automatic Mix cooking Condition
12
WHT-WHT
POWER
TRANSFORMER
RY1
C1
CONTROL UNIT
WHT
STM
STIRRER
MOTOR
WHT
BRN
BLK
DAMPER
SWITCH
RED
E2 E5
HOOD
LAMP
HL
HL
NOISE
FILTER
BLK
BLK
E1
BLK
GRN
N.O.
RY3
PNK
COM
RY3
PPL
RED
BRN PPL
COM
RY2
THERMISTOR
WHT
RY4
N.O.
B7 RY1
BRN WHT
B1
GRY
WHT
BLK
WHT
ORG
ORG
BLK
ORG
ORG
RY5
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
MONITOR
SWITCH
OVEN
OL LAMP
PRIMARY INTERLOCK
RELAY
A3
PNK
A1
RY6
B3
HEATING
ELEMENT
BRN
BRN
HOOD
MOTOR
YEL
RY8
B5
PPL
BLU
C5
RY10
BLU
C7
PPL HOOD
CAPACITOR
RED
BLK
NOISE
RESISTOR
WHT
CONVECTION
MOTOR
CM
ORG
GRN
ORG BLK
A5
FM
FAN
MOTOR
DM
TTM
TURN
DAMPER
TABLE
MOTOR
MOTOR
C9
RY9
GND
BLK
HOOD FAN
THERMAL
CUT OUTS
SECONDARY
INTERLOCK
SWITCH
HIGH
VOLTAGE
CAPACITOR
0.9 F
HIGH
VOLTAGE
RECTIFIER
MAGNETRON
WHT
BLK
BRN C3
PNK
BLK
RED
120VAC
60Hz
MAGNETRON
TEMPERATURE
FUSE
FUSE
20A
RED
ORG
RED
NOTE: RY2 and RY3 will alternately close during cook cycle
R-1855A
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CLOCK APPEARS ON DISPLAY.
RY4
RY7
BLK
BLK
E6 E3
WHT-WHT
WHT
WHT
BRN
BLK
E2 E5
STM
STIRRER
MOTOR
POWER
TRANSFORMER
RED
E1
DAMPER
SWITCH
E4
RY1
C1
RY3
RY2
BRN
BRN
BLK
N.O.
RY3
THERMISTOR
GRN
COM
RY3
PNK
COM
RY2
PPL
RED
N.O.
B7 RY1
BRN PPL
BRN WHT
B1
GRY
WHT
BLK
WHT
RY5
ORG
ORG
BLK
ORG
ORG
B3
MONITOR
SWITCH
OVEN
OL LAMP
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
F2
F3
HIGH
VOLTAGE
CAPACITOR
0.9 F
HIGH
VOLTAGE
RECTIFIER
AH SENSOR
CONTROL UNIT
COM
RY1
WHT
WHT
GRY
YEL
GRY BLU
NOISE
FILTER
RED
GRY
HOOD
LAMP
HL
HL
F1
WHT
PNK
RED
A3
PPL
BLU
RY6
RY8
A1
B5
HEATING
ELEMENT
PRIMARY INTERLOCK
RELAY
BLK
WHT
C5
RY10
BLU
C7
PPL HOOD
CAPACITOR
HOOD
MOTOR
BLK
CONVECTION
MOTOR
CM
ORG
RY9
NOISE
RESISTOR
GND
ORG
A5
FM
FAN
MOTOR
DM
TTM
TURN
DAMPER
TABLE
MOTOR
MOTOR
C9
YEL
BLK
HOOD FAN
THERMAL
CUT OUTS
GRN
BLK
BRN C3
PNK
SECONDARY
INTERLOCK
SWITCH
MAGNETRON
WHT
120VAC
60Hz
MAGNETRON
TEMPERATURE
FUSE
FUSE
20A
RED
BLK
RED
When servicing units with serial number 112162 and above, use the schematics
in Figure 1-1 through 1-4.
ORG
RED
Note:
N.O.
RY2
Ref 2-6(TMAPCB063MRR0)
Figure 1-1. Oven Schematic - Off Condition
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. COOKING TIME PROGRAMMED.
3. START PAD TOUCHED.
RY7
E2 E5
E6 E3
E4
RY3
RY2
F1 F2
F3
AH SENSOR
COM
RY1
WHT
WHT
GRY
GRY
RED
YEL
GRY BLU
WHT-WHT
POWER
TRANSFORMER
RY1
C1
CONTROL UNIT
WHT
STM
STIRRER
MOTOR
WHT
BRN
BLK
DAMPER
SWITCH
RED
E1
BLK
GRN
PNK
N.O.
RY3
HOOD
LAMP
HL
HL
NOISE
FILTER
BLK
BLK
ORG
COM
RY3
PPL
RED
BRN PPL
COM
RY2
THERMISTOR
N.O.
RY2
Ref 2-6(TMAPCB063MRR0)
Figure 1-2. Oven Schematic - Microwave Cooking Condition
13
WHT
RY4
N.O.
B7 RY1
BRN WHT
B1
GRY
WHT
BLK
RY5
WHT
PPL
ORG
BLK
ORG
ORG
RY6
B3
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
MONITOR
SWITCH
OVEN
OL LAMP
PRIMARY INTERLOCK
RELAY
A3
B5
HEATING
ELEMENT
BRN
BRN
A1
PNK
RED
RY8
HOOD
MOTOR
BLK
CONVECTION
MOTOR
CM
ORG
BLU
C5
RY10
BLU
C7
PPL HOOD
CAPACITOR
YEL
BLK
NOISE
RESISTOR
WHT
ORG
A5
FM
FAN
MOTOR
DM
TTM
TURN
DAMPER
TABLE
MOTOR
MOTOR
C9
RY9
GND
BLK
GRN
HOOD FAN
THERMAL
CUT OUTS
SECONDARY
INTERLOCK
SWITCH
HIGH
VOLTAGE
CAPACITOR
0.9 F
HIGH
VOLTAGE
RECTIFIER
MAGNETRON
WHT
BLK
BRN C3
PNK
BLK
RED
120VAC
60Hz
MAGNETRON
TEMPERATURE
FUSE
FUSE
20A
RED
ORG
RED
R-1855A
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. CONVECTION PAD TOUCHED.
3. DESIRED TEMP. TOUCHED.
4. START PAD TOUCHED.
RY5
RY4
E5
E6 E3
BLK
WHT-WHT
WHT
WHT
BRN
BLK
E2
STM
STIRRER
MOTOR
POWER
TRANSFORMER
RED
E1
DAMPER
SWITCH
THERMISTOR
BLK
GRN
PNK
N.O.
RY3
E4
RY1
C1
RY3
RY2
BRN
BRN
BLK
ORG
RY7
COM
RY3
PPL
RED
COM
RY2
BRN PPL
N.O.
B7 RY1
BRN WHT
WHT
GRY
WHT
BLK
RY6
B1
MONITOR
SWITCH
OVEN
OL LAMP
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
HOOD
LAMP
HL
HL
F1
F2
WHT
A3
B3
HEATING
ELEMENT
PRIMARY INTERLOCK
RELAY
PNK
RED
A1
ORG
BLK
ORG
ORG
BLU
B5
RY8
YEL
WHT
C5
RY10
BLU
C7
PPL HOOD
CAPACITOR
PPL
NOISE
RESISTOR
HOOD
MOTOR
BLK
CONVECTION
MOTOR
CM
ORG
RY9
GND
ORG
A5
FM
FAN
MOTOR
DM
TTM
TURN
DAMPER
TABLE
MOTOR
MOTOR
C9
BLK
BLK
GRN
HOOD FAN
THERMAL
CUT OUTS
SECONDARY
INTERLOCK
SWITCH
F3
HIGH
VOLTAGE
CAPACITOR
0.9 F
HIGH
VOLTAGE
RECTIFIER
CONTROL UNIT
COM
RY1
WHT
WHT
GRY
GRY
AH SENSOR
RED
YEL
GRY BLU
NOISE
FILTER
MAGNETRON
WHT
BLK
BRN C3
PNK
BLK
RED
120VAC
60Hz
MAGNETRON
TEMPERATURE
FUSE
FUSE
20A
RED
ORG
RED
N.O.
RY2
Ref 2-6(TMAPCB063MRR0)
Figure 1-3. Oven Schematic - Convection Cooking Condition (CONVEC, PREHEAT, BROIL, SLOW COOK)
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED.
2. MIX COOKING PAD TOUCHED.
3. DESIRED TEMP. TOUCHED.
4. COOKING TIME PROGRAMMED.
5. START PAD TOUCHED.
E6 E3
WHT-WHT
WHT
STM
STIRRER
MOTOR
WHT
BRN
BLK
E2 E5
DAMPER
SWITCH
E4
RY1
C1
RY3
RY2
F1
F2
F3
AH SENSOR
COM
RY1
WHT
WHT
GRY
GRY
RED
YEL
GRY BLU
CONTROL UNIT
POWER
TRANSFORMER
RED
E1
BLK
GRN
PNK
N.O.
RY3
HOOD
LAMP
HL
HL
NOISE
FILTER
BLK
BLK
ORG
RY7
COM
RY3
PPL
RED
COM
RY2
BRN PPL
N.O.
B7 RY1
THERMISTOR
N.O.
RY2
Ref 2-6(TMAPCB063MRR0)
Figure 1-4. Oven Schematic - Automatic Mix cooking Condition
14
WHT
RY4
BRN WHT
B1
GRY
WHT
BLK
RY5
WHT
PPL
ORG
BLK
ORG
ORG
RY6
B3
DOOR
SENSING
SWITCH
THIRD DOOR
SWITCH
MONITOR
SWITCH
OVEN
OL LAMP
PRIMARY INTERLOCK
RELAY
PNK
A3
B5
HEATING
ELEMENT
BRN
BRN
A1
YEL
RY8
HOOD
MOTOR
BLK
CONVECTION
MOTOR
CM
ORG
BLU
C5
RY10
BLU
C7
PPL HOOD
CAPACITOR
RED
BLK
NOISE
RESISTOR
WHT
ORG
A5
FM
FAN
MOTOR
DM
TTM
TURN
DAMPER
TABLE
MOTOR
MOTOR
C9
RY9
GND
BLK
GRN
HOOD FAN
THERMAL
CUT OUTS
SECONDARY
INTERLOCK
SWITCH
HIGH
VOLTAGE
CAPACITOR
0.9 F
HIGH
VOLTAGE
RECTIFIER
MAGNETRON
WHT
BLK
BRN C3
PNK
BLK
RED
120VAC
60Hz
MAGNETRON
TEMPERATURE
FUSE
FUSE
20A
RED
ORG
RED
NOTE: RY2 and RY3 will alternately close during cook cycle
R-1855A
DESCRIPTION AND FUNCTION OF COMPONENTS
operate inversely.)
3. If the door is opened, and the primary interlock relay,
secondary interlock switch and third door switch contacts
fail to open, the monitor fuse blows simultaneously with
closing of the monitor switch contacts.
CAUTION: BEFORE REPLACING A BLOWN MONITOR
FUSE, TEST THE PRIMARY INTERLOCK RELAY, THIRD DOOR SWITCH, DOOR SENSING SWITCH, MONITOR SWITCH AND SECONDARY INTERLOCK SWITCH FOR PROPER
OPERATION. (REFER TO CHAPTER "TEST
PROCEDURE").
NOTE: MONITOR FUSE, SECONDARY INTERLOCK
SWITCH AND MONITOR SWITCH ARE
REPLACED AS AN ASSEMBLY.
DOOR OPEN MECHANISM
The door is opened by pushing the open button on the control
panel, refer to the Figure D-1.
When the open button is pushed, the open button pushes up
the open lever, and then the open lever pushes up the latch
head. The latch heads are moved upward and released from
latch hook. Now the door will open.
LATCH HOOK
LATCH
HEADS
DOOR SENSING
SWITCH
TEMPERATURE FUSE (MG)
MONITOR FUSE
The temperature fuse located near the waveguide is
designed to prevent damage to the magnetron if an over
heated condition develops in the tube due to cooling fan
failure, obstructed air guide, dirty or blocked air intake, etc.
Under normal operation, the temperature fuse remains closed.
However, the temperature fuse will open at 302OF (150OC)
causing the oven to shut down.
MONITOR
SWITCH
THIRD
DOOR
SWITCH
DOOR
OPEN LEVER
SECONDARY
INTERLOCK
SWITCH
THERMAL CUT-OUT (HOOD )
This thermal cut-out located on the base plate right and the
hood intake duct (left), It is designed to automatically turn
on the hood fan motor whenever the hot air rising from the
conventional range below causes the temperature at the
thermal cut-out to rise to 140OF (60OC) or higher, thus
removing this hot air from around microwave oven. When
the temperature around the thermal cut-out drops to 113OF
(45OC) or lower, the thermal cut-out shuts off the food fan
motor.
Figure D-1. Door Open Mechanism
SECONDARY INTERLOCK SWITCH, THIRD DOOR
SWITCH & DOOR SENSING SWITCH
The secondary interlock switch and third door switch
mounted parrallel to each other horizontally in the upper
positions of the latch hook, the door sensing switch is
mounted horizontally in the upper position of the latch hook.
They are activated by the latch head on the door. When the
door is opened, the switches interrupt the power to all high
voltage components, except the oven lamp . A cook cycle
cannot take place until the door is firmly closed thereby
activating all interlock switches. The interlock system
consists of the door sensing switch and the primary
interlock relay located on the control circuit board.
TURNTABLE MOTOR
The turntable motor rotates the turntable located on the
bottom of the oven cavity, so that the foods on the turntable
cook evenly during cooking. Turntable will turn in either
direction. The turntable motor can be turned off by touching
TURNTABLE ON/OFF pad.
MONITOR SWITCH
COOLING FAN MOTOR
The monitor switch is activated (the contacts opened) by the
latch head on the door while the door is closed. The switch
is intended to render the oven inoperative, by means of
blowing the monitor fuse, when the contacts of the secondary interlock switch and third door switch fail to open when
the door is opened.
The cooling fan motor drives a blade which draws external
cool air. This cool air is directed through the air vanes
surrounding the magnetron and cools the magnetron. This
air is channelled through the oven cavity to remove steam
and vapors given off from the heating foods. It is then
exhausted through the exhausting air vents at the oven
cavity.
Functions:
1. When the door is opened, the monitor switch contact close
(to the ON condition) due to their being normally closed.
At this time the primary interlock relay, secondary interlock
switch and third switch are in the OFF condition (contacts
open) due to their being normally open contact switches.
2. As the door goes to a closed position, the monitor switch
contacts are first opened and then the door sensing switch,
secondary interlock switch and third door switch contacts
close. (On opening the door, each of these switches
HOOD FAN MOTOR
The hood fan motor is a two-speed, single-phase, double
pole induction type, requiring a hood fan capacitor. It is
located outside the upper rear part of the oven cavity, is to
remove, from around the oven, hot air rising from the
conventional electric or gas range over which it is installed.
This air is then expelled either vertically or horizontally
through the customer supplied duct system, or discharged
back into the kitchen.
15
R-1855A
Damper Operation
1. When power supply cord is plugged in:
1-1. When power supply cord is plugged in, a signal is
sensed in the control unit, and operates shut-off
relay (RY6).
1-2. Contacts of shut-off relay (RY6) close, the damper
motor is energized, opening the damper plate.
1-3. When the damper is moved to the open position by
the damper cam the damper switch is closed (ON
position).
1-4. The signal from damper switch is re-sensed in the
control unit and shut-off relay (RY6) is turned off.
1-5. The 120 volts A.C. to the damper motor is removed
and the motor turns off.
2. When oven is microwave cooking:
Damper is in the open position.
3. When oven is convection cooking:
3-1. Damper motor is energized by touching the
convection, temperature, number and START pads.
3-2. When damper is in the closed position (damper
switch is OFF), its signal is sensed by the control
unit, and shut-off relay (RY6) is de-energized.
3-3. The damper is held in the closed position during the
convection cooking operation.
3-4. At the end of the convection cooking, shut-off relay
(RY6) is energized, and the damper is returned to
the open position.
NOTE: If the damper plate is not in the proper position,
closed during convection or open during microwave,
the control unit will stop oven operation after 1
minute.
STIRRER MOTOR
The stirrer motor drives the stirrer fan to stir the microwave
radiation from the waveguide.
HOOD LAMP
The hood lamps are mounted at the hood lamp angle on the
base cover. When the hood lamp button is pushed, the hood
lamp relay (RY8) contacts close turning both hood lamps on.
HEATING ELEMENT
The heating element is located at the left side of the oven
cavity. It is intended to heat air driven by the convection fan.
The heated air is kept in the oven and force-circulated and
reheated by the heating element.
CONVECTION COOKING SYSTEM
This oven is designed with a hot air heating system where
food is not directly heated by the heating element, but is
heated by forced circulation of the hot air produced by the
heating element.
The air heated by the heating element is circulated through
the convection passage provided on the outer casing of the
oven cavity by means of the convection fan which is driven
by the convection motor. It then enters the inside of the oven
through the vent holes provided on the left side of the oven.
Next, the hot air heats the food on the turntable and leaves
the oven cavity through the vent in the center of the oven
cavity left side wall.
Without leaving the oven, this hot air is reheated by the
heating element, passes through the convection passage
and enters the inside of the oven cavity again, in a continuing
cycle.
In this way, the hot air circulates inside the oven cavity to
raise its temperature and, at the same time, comes into
contact with the food being cooked.
When the temperature inside the oven cavity reaches the
selected temperature, the heating element is de-energized.
When the temperature inside the oven cavity drops below
the selected temperature, the heating element is energized
again. In this way, the inside of the oven cavity is maintained
at approximately the selected temperature.
When the convection time reaches 0, the heating element
is de-energized and the convection fan stops operating and
the oven shuts off.
DAMPER PLATE
DAMPER CAM
DAMPER SWITCH
DAMPER MOTOR
Figure D-2. Damper Mechanism
DAMPER OPEN-CLOSE MECHANISM
Usually, the damper is in the open position except during
convection cooking. Damper position is set automatically
by damper motor, damper switch and motor cam. These
components are operated by a signal that judges if microwave cooking or convection cooking operation is selected
by the control unit.
Microwave Cooking:
Damper is in the open position, because a portion of cooling
air is channeled through the cavity to remove steam and
vapors given off from the heating foods.
It is then exhausted at the top of the oven cavity into a
condensation compartment.
Convection Cooking:
Damper is in the closed position, so that no hot air will be
allowed to leak out the oven cavity.
16
R-1855A
TROUBLESHOOTING GUIDE
Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is connected.
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many
of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter
which will be found in the "Test Procedure "section.
IMPORTANT: If the oven becomes inoperative because of a blown monitor fuse, check the secondary interlock switch,
door sensing switch, primary interlock relay(RY2), third door switch and monitor switch, before replacing
the monitor fuse. If the monitor fuse is replaced, the monitor switch and primary switch must also be replaced.
Use part FFS-BA018/KIT as an assembly.
IMPORTANT: Whenever troubleshooting is performed with the power supply cord disconnected. It may in, some cases,
be necessary to connect the power supply cord after the outer case has been removed, in this event,
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
When the testing is completed
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is installed.
7. Run the oven and check all functions.
17
R-1855A
TROUBLESHOOTING GUIDE
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many
of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which
will be found in the "Test Procedure" section.
Home fuse blows when power cord is plugged into wall receptacle.
Monitor fuse blows when power cord is plugged into wall receptacle.
Display does not illuminate when power cord is first plugged into wall receptacle.
OFF
CONDITION
Display does not operate properly when STOP/CLEAR key is touched. (The
time of day should appear on the display with beep sound during normal
condition.)
Oven lamp does not light with door is opened.
Hood fan motor operates when power cord is first plugged into wall receptacle.
Temperature of oven base seems more than 140½F (60½C) because of operation
of the range below. But hood fan motor does not turn on automatically.
(Normally, food fan motor should be operating at low speed.)
Hood lights do not turn on with pushed HOOD LAMP button.
IDLE
CONDITION
Hood fan motor does not rotate at all with pushed FAN button.
Speed of the hood fan motor does not change when the FAN button is touched
for this function.
Oven lamp does not light in cook cycle. (But it does light when door is opened.)
COOKING
CONDITION
(COMMON)
Fan motor does not operate. (Oven lamp and turntable motor operate.)
Turntable motor does not operate (Oven lamp lights and fan motor operate.)
Cooking cycle runs 1 minute then shuts down.
Oven does not go into cook cycle when START pad is touched
Oven seems to be operating but little or no heat is produced in oven load. (Food
incompletely cooked or not cooked at all at end of cook cycle.)
MICROWAVE
COOKING
CONDITION
Oven goes into a cook cycle but extremely uneven heating is produced in oven
load (food).
Variable cooking does not operate properly except Cooking Power 10 (P-HI)
mode.
Function of COMPU DEFROST does not operate properly.
Stirrer motor does not operate. (Other parts operate.)
CONV indicator lights, but oven does not go into cook cycle when START pad
is touched.
CONVECTION
COOKING
CONDITION
CONV indicator lights, but heating element does not heat.
Temperature in the oven cavity is lower or higher than preset.
Convection motor does not operate.
Convection cycle runs 4 minutes and 15 seconds then shuts down.
SENSOR
COOKING
CONDITION
The oven stops and "ERROR" is displayed or does not end during Sensor
Cooking condition. (Oven does not shuts off after a cup of water is boiling by
Sensor Cooking.)
Oven stops at 32 seconds after starting.
18
I
J K
L
MONITOR FUSE
TEMPERATURE FUSE (MG)
THERMISTOR
HOOD THERMAL CUT-OUT
G H
DAMPER SWITCH
PRIMARY INTERLOCK SYSTEM
SEC. INTERLOCK AND DOOR SEN. SWITCH
HIGH VOLTAGE CAPACITOR
PROBLEM
H.V. RECTIFIER
CONDITION
MAGNETRON
POSSIBLE CAUSE
AND
DEFECTIVE PARTS
POWER TRANSFORMER
A B C D E F
TEST PROCEDURE
MONITOR SWITCH
CK = Check / RE = Replace
19
NOISE FILTER
LOW VOLTAGE
NO POWER AT OUTLET
SHORTED IN POWER CORD
SHORTED OR OPENED WIRING
HOOD MOTOR CAPACITOR
HOOD LAMP OR SOCKET
CONVECTION MOTOR
TURNTABLE OFF CONDITION
STIRRER MOTOR
TURNTABLE MOTOR
FAN MOTOR
OVEN LAMP OR SOCKET
AH SENSOR
FOIL PATTERN ON PWB.
RELAY (RY10)
RELAY (RY9)
M N O P Q R S S S S S S S
RELAY (RY8)
RELAY (RY7)
RELAY (RY6)
RELAY (RY5)
RELAY (RY4)
RELAY (RY3)
RELAY (RY2)
RELAY (RY1)
KEY UNIT
CONTROL UNIT
CHECKING TEMPERATURE
CONVECTION HEATER
DAMPER MOTOR
HOOD FAN MOTOR
R-1855A
IMPORTANT: If the oven becomes inoperative because of a blown monitor fuse, check the monitor switch, primary
interlock relay, door sensing switch, third door switch and secondary interlock switch before replacing the
monitor fuse. If monitor fuse is replaced, the monitor switch must also be replaced. Use part FFS-BA018/
KIT as an assembly.
S S S U V RE RE RE RE CK CK RE CK RE RE CK CK W
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
A
COMPONENT TEST
MAGNETRON ASSEMBLY TEST
1.
2.
3.
4.
5.
6.
7.
8.
9.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check
across the magnetron filament leads should indicate less than 1 ohm.
To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads
and chassis ground. This test should indicate an infinite resistance. If there is little or no resistance
the magnetron is grounded and must be replaced.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
MICROWAVE OUTPUT POWER
The following test procedure should be carried out with the microwave oven in a fully assembled condition
(outer case fitted).
HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD
BE OBSERVED.
Power output of the magnetron can be measured by performing a water temperature rise test. This test
should only be used if above tests do not indicate a faulty magnetron and there is no defect in the following
components or wiring: silicon rectifier, high voltage capacitor and power transformer. This test will
require a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple type
temperature tester. For accurate results, the following procedure must be followed carefully:
1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water
with a thermometer or thermocouple temperature tester. Stir the thermometer or thermocouple
through the water until the temperature stabilizes. Record the temperature of the water.
2. Place the cup of water in the oven. Operate oven at POWER 10(HIGH) selecting more than 60
seconds cook time. Allow the water to heat for 60 seconds, measuring with a stop watch, second
hand of a watch or the digital read-out countdown.
3. Remove the cup from the oven and again measure the temperature, making sure to stir the
thermometer or thermocouple through the water until the maximum temperature is recorded.
4. Subtract the cold water temperature from the hot water temperature. The normal result should be
21 to 39OF(11.7 to 21.7O) rise in temperature. If the water temperatures are accurately measured
and tested for the required time period the test results will indicate if the magnetron tube has low
power output (low rise in water temperature) which would extend cooking time or high power output
(high rise in water temperature) which would reduce cooking time. Because cooking time can be
adjusted to compensate for power output, the magnetron tube assembly should be replaced only if
the water temperature rise test indicates a power output well beyond the normal limits. The test is
only accurate if the power supply line voltage is 120 volts and the oven cavity is clean.
B
POWER TRANSFORMER TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the primary input terminals and measure the resistance of the transformer with an
ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance
of the primary coil should be less than 1 ohm and the resistance of the high voltage coil should be
approximately 123 ohms; the resistance of the filament coil should be less than 1 ohm.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO
MEASURE THE FILAMENT AND HIGH VOLTAGE.)
20
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
C
COMPONENT TEST
HIGH VOLTAGE RECTIFIER TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance
across the terminals and observe, reverse the leads to the rectifier terminals and observe meter
reading. If a short is indicated in both directions, or if an infinite resistance is read in both directions,
the rectifier is probably defective and should be replaced.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.
D
HIGH VOLTAGE CAPACITOR TEST
1.
2.
3.
4.
5.
6.
7.
8.
E
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the capacitor is open, no high voltage will be available to the magnetron. Disconnect input leads
and check for short or open between the terminals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate
continuity for a short time and should indicate an open circuit once the capacitor is charged. If the
above is not the case, check the capacitor with an ohmmeter to see if it is shorted between either
of the terminals and case. If it is shorted, replace the capacitor.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
SECONDARY INTERLOCK SWITCH AND THIRD DOOR SWITCH TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the secondary interlock switch.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
PRIMARY INTERLOCK SYSTEM TEST
DOOR SENSING SWITCH
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the door sensing switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the cooling
fan, turntable and oven light will be activated by RY1.
21
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
F
G
COMPONENT TEST
PRIMARY INTERLOCK RELAY (RY2)
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect two (2) wire leads from the male tab terminals of the Secondary Interlock Relay. Check
the state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay
contacts are closed, replace the circuit board entirely or the relay itself.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
MONITOR SWITCH TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Before performing this test, make sure that the primary interlock switch and the secondary interlock
relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire
lead from the monitor switch (NC) terminal. Check the monitor switch operation by using the
ohmmeter as follows. When the door is open, the meter should indicate a closed circuit. When the
monitor switch actuator is pushed by a screw driver through the lower latch hole on the front plate
of the oven cavity with the door opened (in this condition the plunger of the monitor switch is pushed
in), the meter should indicate an open circuit. If improper operation is indicated, the switch may be
defective. After testing the monitor switch, reconnect the wire lead to the monitor switch (NC) terminal
and check the continuity of the monitor circuit.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all
functions.
WHITE
BLACK
BLACK
SCREW
DRIVER
MONITOR SWITCH
H
DAMPER SWITCH TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor
Disconnect the wire leads from the switch terminals and connect ohmmeter leads to the
common (COM.) and normally open (N.O.) terminals of the switch.
5. When switch actuator is pushed by the damper cam, the meter should be indicated a closed circuit.
6. When power cord is plugged into the wall receptacle, the damper motor operates and damper cam
will start to rotate. When the switch actuator is released, the meter should be indicated an open circuit.
If improper operation is indicated, replace the damper switch.
7. Reconnect all leads removed from components during testing.
8. Reinstall the outer case (cabinet).
9. Reconnect the power supply cord after the outer case is installed.
10.Run the oven and check all
functions.
22
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
I
COMPONENT TEST
BLOWN MONITOR FUSE
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the monitor fuse is blown when the door is opened, check the secondary interlock relay, secondary,
primary switch and monitor switch according to the "TEST PROCEDURE" for those switches before
replacing the blown monitor fuse.
CAUTION: BEFORE REPLACING A BLOWN MONITOR FUSE, TEST THE PRIMARY INTERLOCK
RELAY, SECONDARY INTERLOCK SWITCH, THIRD DOOR SWITCH, DOOR SENSING
SWITCH AND MONITOR SWITCH FOR PROPER OPERATION.
If the monitor fuse is blown by improper switch operation, the monitor fuse and monitor switch must
be replaced with "monitor fuse and monitor switch assembly" part number FFS-BA018/KiT, even if
the monitor switch operates normally. The monitor fuse and monitor switch assembly is comprised
of a 20 ampere fuse and switch.
5. Reconnect all leads removed from components during testing.
6. Re-install the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
J
TEMPERATURE FUSE TEST
MAGNETRON TEMPERATURE FUSE
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. A continuity check across the temperature fuse terminals should indicate a closed circuit. If the
temperature of the magnetron reaches approximately 302OF(150OC), the temperature fuse opens.
An open temperature fuse indicates overheating of the magnetron. Check for restricted air flow to
the magnetron, especially the cooling fan air guide.
5. Reconnect all leads removed from components during testing.
6. Re-install the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
CAUTION: IF THE TEMPERATURE FUSE INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE, REPLACE THE TEMPERATURE FUSE.
K
HOOD THERMAL CUT-OUT TEST
1.
2.
3.
4.
5.
6.
7.
8.
L
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
A continuity check across the thermal cut-out terminals should indicate an open circuit unless the
temperature of the thermal cut-out reaches approximately 140OF(60OC) or more. At that temperature,
the contacts will close. The thermal cut-out opens automatically at approximately 113OF(45OC).
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
THERMISTOR TEST
Disconnect connector-E from the control unit. Measure the resistance of the thermistor with an
ohmmeter. Connect the ohmmeter leads to Pin No’s E-3 and E-4.
Room Temperature
68FO(20OC) - 86OF(30OC)
Resistance
Approx. 360k ohm - 152k ohm
If the meter does not indicate above resistance, replace the thermistor
23
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
M
COMPONENT TEST
HOOD FAN MOTOR TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the motor does not turn, touch the HOOD FAN button once (set hood fan motor power "HIGH")
and check voltage between pins "1" and "2" (Blue and Black wires) of the 6 pin connector. If 120 Volts
appear and the hood capacitor is good, replace the hood fan assembly. If 120 Volts does not appear,
check the motor circuit. The resistance values of motor terminals are as follows:
YLW
BLU
HOOD
FAN
CAPACITOR
5
Resistance between;
1
4
32
45
20
2
BLU (1)
BLK (2)
BLU (1)
BLK (2)
WHT (3)
AND YLW (4) = 0 ohm (Shorted)
AND YLW (4) = 32 ohm
AND BLK (2) = 32 ohm
AND WHT (3) = 20 ohm
AND RED (5) = 45 ohm
BLK
RED
BLU BLK WHT
1
2
3
3
WHT
6-PIN CONNECTOR
OF HOOD FAN MOTOR
4
5
YLW RED
5.
6.
7.
8.
N
DAMPER MOTOR TEST
1.
2.
3.
4.
5.
6.
7.
8.
9.
O
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
When the power cord is plugged into the wall receptacle and 120 volts A.C. is supplied to the damper
motor, the motor operates until the damper is opened and the damper switch closes. Then the damper
motor stops operation.
If the damper motor does not operate, check for A.C. voltage with a voltmeter at the motor.
Disconnect the power cord from the wall receptacle.
Disconnect the wire leads of motor and connect the meter leads to the wire leads of main wire harness.
Re-connect the power cord into the wall receptacle.
If 120 volts A.C. is indicated at the wire leads, replace the motor and if 120 volts A.C. is not indicated,
check the wire harness and control unit.
Run the oven and check all functions.
HEATING ELEMENT TEST
1.
2.
3.
4.
a.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Make sure the heating element is fully cooled and test as follows;
Disconnect wire leads and measure the resistance with an ohmmeter. On the R x 1 scale, the
resistance between the heating element terminals should be approximately 10 ohm.
Disconnect wire leads and measure the insulation resistance with 500V - 100M ohm insulation
resistance meter. The insulation resistance between heating element terminal and cavity should be
more than 0.5M ohm.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
24
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
P
COMPONENT TEST
CHECKING TEMPERATURE IN THE CONVECTION MODE
1.
2.
3.
4.
5.
6.
7.
8.
Q
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
It is difficult to measure the exact temperature in the convection oven. An accurate thermocouple
type temperature tester must be used. A low priced bi-metal type thermometer is not reliable or
accurate. The temperature should be checked with outer case cabinet installed, approx. 5 minutes
after preheat temperature is reached (audible signal sounds four times). The temperature experienced
may be approx. 30OF more or less than indicated on the display, however, in most cases the food
cooking results will be satisfactory. Difference in power supply voltage will also affect the oven
temperature.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
TOUCH CONTROL PANEL ASSEMBLY TEST
The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore,
unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter
and ohmmeter.
In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key
Unit, and also the Control Unit is divided into two units, LSI Unit and Power Unit, and troubleshooting
by unit replacement is described according to the symptoms indicated.
Before testing,
1) Disconnect the power supply cord, and then remove outer case. Refer to procedure of "HOOD
EXHAUST LOUVER REMOVAL", "REMOVAL OF OVEN FROM WALL" and "OUTER CASE
REMOVAL".
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
6) After that procedure, re-connect the power supply cord.
1. Key Unit.
NOTE ;
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Check key unit ribbon connection before replacement.
5) Reconnect all leads removed from components during testing.
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.
The following symptoms indicate a defective key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
If the key unit is defective.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Replace the key unit.
5) Reconnect all leads removed from components during testing.
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.
25
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
Q
COMPONENT TEST
TOUCH CONTROL PANEL ASSEMBLY TEST
2. Control Unit.
The following symptoms indicate a defective control unit. Before replacing the control unit, perform
the Key unit test (Procedure R) to determine if control unit is faulty.
2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) The figure of all digits flicker.
2-3 Other possible problems caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
When testing is completed,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Reconnect all leads removed from components during testing.
5) Re-install the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions.
R
KEY UNIT TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon is
making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing
(stop switch) is good, disconnect the flat ribbon that connects the key unit to the control unit and
make sure the door sensing switch is closed (either close the door or short the stop switch connecter).
Use the key unit matrix indicated on the control panel schematic and place a jumper wire between
the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control unit
responds by clearing with a beep, the key unit is faulty and must be replaced. If the control unit does
not respond, it is faulty and must be replaced. If a specific pad does not respond, the above method
may be used ( after clearing the control unit) to determine if the control unit or key pad is at fault.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
G1
G2
G3
G4
G5
G6
G7
G8
CUSTOM
HELP
SENSOR
REHEAT
MINUTE
PLUS
POPCORN
COMPU
DEFROST
SENSOR
COOK
COMPU
BROIL
G9
CONVEC
PREHEAT
LOW MIX
BAKE
HIGH MIX
ROAST
COMPU
ROAST
COMPU
BAKE
G10
BROIL
SLOW
COOK
G11
KITCHEN
TIMER
CLOCK
G12
TURNTABLE
ON / OFF
POWER
LEVEL
26
1
2
3
4
5
100°F
150°F
275°F
300°F
325°F
6
7
8
9
0
350°F
375°F
400°F
425°F
450°F
KEEP
WARM
STOP
CLEAR
START
TOUCH ON
FAN
LIGHT
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
S
COMPONENT TEST
RELAY TEST
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape.
6. After that procedure, re-connect the power supply cord.
7. Remove the outer case and check voltage between Pin No. 5 of the 3-pin connector (A) and the
common terminal of the relay RY1 on the control unit with an A.C. voltmeter. The meter should indicate
120 volts, if not check oven circuit.
Relay Test
These relays are operated by D.C. voltage.
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.
DC. voltage indicated............Defective relay.
DC. voltage not indicated.......Check diode which is connected to the relay coil. If diode is good, control
unit is defective.
RELAY SYMBOL
OPERATIONAL VOLTAGE
CONNECTED COMPONENTS
RY1
Approx. 24.0V D.C.
Oven lamp
RY2(COOK)
Approx. 24.0V D.C.
Power transformer / Stirrer mootor
RY3
Approx. 24.0V D.C.
Heating element
RY4
Approx. 24.0V D.C.
Turntable motor
RY5
Approx. 24.0V D.C.
Fan motor
RY6
Approx. 24.0V D.C.
Damper motor
RY7
Approx. 24.0V D.C.
Convection motor
RY8
Approx. 24.0V D.C.
Hood lamp
RY9
Approx. 24.0V D.C.
Hood motor
RY10
Approx. 24.0V D.C.
Hood motor (HIGH / LOW selection)
8. Disconnect the power supply cord, and then remove outer case.
9. Open the door and block it open.
10.Discharge high voltage capacitor.
11.Reconnect all leads removed from components during testing.
12.Re-install the outer case (cabinet).
13.Reconnect the power supply cord after the outer case is installed.
14.Run the oven and check all functions.
T
COMPU DEFROST TEST
1. Place one cup of water in the center of the turntable tray in the oven cavity.
2. Close the door, touch the " COMPU DEFROST " pad four times.
3. Touch the number 5 pad.
4. Touch " START " pad.
5. The oven will operate as follows.
MENU
CHICKEN
PIECES
WEIGHT
(LBS)
0.5
1ST STAGE
LEVEL TIME
70% 28sec.
2ND STAGE
LEVEL
TIME
50%
5sec.
3RD STAGE
LEVEL
TIME
30%
1min.28sec.
6. If improper operation is indicated, the control unit is probably defective and should be checked.
27
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
U
COMPONENT TEST
PROCEDURES TO BE TAKEN WHEN THE FOIL PATTERN ON THE PRINTED WIRING BOARD
PWB IS OPEN
To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary on
the PWB, this foil pattern acts as a fuse.
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. If the foil pattern is open, follow the troubleshooting guide given below for repair.
Problem: POWER ON, indicator does not light up.
STEPS
1
CAUSE OR CORRECTION
Check supply voltage and oven main unit.
2
The rated voltage is applied to primary side
power transformer.
Power transformer or secondary circuit defective.
Check and repair.
3
Only pattern at "a" is broken.
*Insert jumper wire (J1) and solder.
4
Pattern at "a" and "b" are broken.
*Insert the coil RFILN0027WRE0 between "c" and "d".
NOTE:*
P
2
1
b
a
C100
d
T1
VRS1
(J1)
At the timeof making these repairs,
make a visual inspection of the
varistor Check for burned damage
and examine the transformer with
an ohm-meter for the presense of
a layer short-circuit(check Primary
coil resistance which is approxi
mately 195 ohm ± 15%). If any
abnormal condition is detected,
replace the defective parts.
RY1
V
OCCURRENCE
The rated voltage is not applied between Pin
No. 5 of the 3-Pin connector (A) and the
terminal of the relay RY1.
CN - B
c
CN - A
5
AC (N)
3
1
MOTOR
CAPACITOR
AH SENSOR TEST
Checking the initial sensor cooking condition
Warning: The oven should be fully assembled before following procedure.
(1) The oven should be plugged in at least five minutes before sensor cooking.
(2) Room temperature should not exceed 95O F(35OC).
(3) The unit should not be installed in any area where heat and steam are generated. The unit should
not be installed, for example, next to a conventional surface unit. Refer to the " INSTALLATION
Instructions ".
(4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To
permit adequate ventilation, be sure to install so as not to block these vents. There should be some
space for air circulation.
(5) Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any moisture
with a dry cloth or paper towel.
(6) The Sensor works with food at normal storage temperature.For example, chicken pieces would be
at refrigerator temperature and canned soup at room temperature.
(7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The
sensor will detect the vapor given of by the spray and turn off before food is properly cooked.
(8) If the sensor has not detected the vapor of the food, ERROR will appear and the oven will shut off.
28
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
Water load cooking test
Make sure the oven has been plugged in at least five minutes before checking sensor cook operation.
The cabinet should be installed and screws tightened.
(1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
(2) Place the container on the center of tray in the oven cavity.
(3) Close the door.
(4) Touch SENSOR COOK pad. And touch the number pad 1. And touch the start pad. The oven will
operate for the first 32 seconds, without generating microwave energy.
NOTE: ERROR will appear if the door is opend or STOP/CLEAR pad is touched during first stage of
sensor cooking.
(5) After approximately 32 seconds, microwave energy is produced, oven should turn off after water
is boiling (bubbling).
If the oven does not turn off, replace the AH sensor or check the control unit, refer to explanation below.
TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement
sensor.
(1) Disconnect oven from power supply and remove outer case.
(2) Open the door and block it open.
(3) Discharge the high voltage capacitor.
(4) Remove the AH sensor.
(5) Install the new AH sensor.
(6) Reconnect all leads removed from the components during replacing.
(7) Re-install the outer case.
(8) Reconnect the oven to the power supply and check the sensor cook operation proceed as follows:
9-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
9-2. Place the container on the center of tray in the oven cavity.
9-3. Close the door.
9-4. Touch SENSOR COOK pad. And touch the number pad 1. And touch the start pad.
9-5. The oven will turn off automatically after the water is boiling (bubbling).
If new sensor dose not operate properly, the problem is with the control unit.
CHECKING CONTROL UNIT
(1) Disconnect oven from power supply and remove outer case.
(2) Open the door and block it open.
(3) Discharge the high voltage capacitor.
(4) Disconnect the wire leads from the cook relay.
(5) Disconnect the sensor connector that is mounted to lower portion of control panel.
(6) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel.
(7) Reconnect the oven to the power supply and check the sensor cook operation proceed as follows:
7-1. Touch SENSOR COOK pad. And touch the number pad 1. And touch the start pad.
7-2. The control panel is in the sensor cooking operation.
7-3. After approximately 32 seconds, push plunger of select switch. This condition is same as
judgement by AH sensor.
7-4. After approximately 3 seconds, cooking operation turns off, an audible signal will sound,
and the display will then revert to the time of day.
If the above is not the case, the control unit is probably defective.
If the above is proper, the AH sensor is probably defective.
R1,R2 : 22 ohm ± 1% 1/2W
R3 : 10k ohm ± 5% 1/4W
R4 : 1M ohm ± 5% 1/4W
Plunger
Sensor Dummy Resistor Circuit
NC
NO
To connector (F)
on Control Unit.
1
F-1
F-2
COM
COM
2
3
NO
R1
F-3
R2
CONNECTOR
29
R3
R4
NC
R-1855A
TEST PROCEDURES
PROCEDURE
LETTER
W
COMPONENT TEST
NOISE FILTER TEST
1.
2.
3.
4.
5.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the leads to the primary of the power transformer.
Using an ohm-meter, check between the terminals as described in the following table:
NOISE FILTER UNIT
MONITOR
FUSE
NOISE SUPPRESSION COIL
LINE CROSS CAPACITOR
0.22uF/ AC 250V
LINE BYPASS CAPACITOR
LINE BYPASS CAPACITOR
0.0033uF/ AC
0.0033uF/ AC
125V
125V
GRY
MEASURING POINT
RED
INDICATION OF OHM-METER
Between N and H
Open Circuit
Between terminal N and GRY
Short Circuit
Between terminal H and RED
Short Circuit
If incorrect readings are obtained, replace the noise filter.
6.
7.
8.
9.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
30
R-1855A
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
The touch control section consists of the following units
as shown in the touch control panel circuit.
3) Synchronizing Signal Circuit
The power source synchronizing signal is available in
order to compose a basic standard time in the clock
circuit. It incorporates a very small error because it works
on commercial frequency.
(1) Key Unit
(2) Control Unit
The principal functions of these units and the signals communicated among them are explained below.
4) ACL Circuit
A circuit to generate a signals which resetting the LSI to
the initial state when power is applied.
Key Unit
The key unit is composed of a matrix, signals generated in
the LSI are sent to the key unit through P00 - P06.
When a key pad is touched, a signal is completed through
the key unit and passed back to the LSI through AN1 and
R24 - R27 to perform the function that was requested.
5) Buzzer Circuit
The buzzer is responds to signals from the LSI to emit
audible sounds (key touch sound and completion sound).
6) Temperature Measurement Circuit : Oven
The temperature in the oven cavity is sensed by the
thermistor. The variation of resistance according to sensed
temperature is detected by the temperature measurement circuit and the result applied to LSI. The LSI uses
this information to control the relay and display units.
Control Unit
Control unit consists of LSI, power source circuit, synchronizing signal circuit, ACL circuit, buzzer circuit, temperature
measurement circuit, absolute humidity sensor circuit, relay
circuit and indicator circuit.
7) Absolute Humidity Sensor Circuit
This circuit detects the humidity of a food which is being
cooked, to control its automatic cooking.
1) LSI
This LSI controls the temperature measurement signal,
AH sensor signal, key strobe signal, relay driving signal
for oven function and indicator signal.
8) Door Sensing Switch
A switch to inform the LSI if the door is open or closed.
2) Power Source Circuit
This circuit generates voltages necessary for the control
unit from the AC line voltage.
Symbol
Voltage
Application
VC
VP
-5.1V
-31V
VF1
2.9Vac
LSI(IC1)
Fluorescent display tube : Grid
and anode voltage
Filament of fluorescent
dis play tube
(VF1 to VF2 voltage)
VF2
9) Relay Circuit
To drive the magnetron, heating element, fan motor,
convection motor, damper motor, turntable motor, hood
motor, and light the oven lamp and hood lamp.
10) Indicator Circuit
Indicator element is a Fluorescent Display.
Basically, a Fluorescent Display is triode having a cathode, a grid and an anode. Usually, the cathode of a
Fluorescent Display is directly heated and the filament
serves as cathode.
The Fluorescent Display has 8-digits, 16-segments are
used for displaying figures.
31
R-1855A
DESCRIPTION OF LSI
LSI(IZA719DR)
The I/O signals of the LSI(IZA719DR) are detailed in the following table.
Pin No.
Signal
I/O
Description
1
VCC
IN
Connected to GND.
Anode (segment) of Fluorescent Display illumination voltage: -31V.
2
VEE
IN
Vp voltage of power source circuit input.
3
AVSS
IN
Power source voltage:-5V.
VC voltage of power source circuit input.
4
VREF
IN
Reference voltage input terminal.
A reference voltage applied to the A/D converter in the LSI. Connected to GND.(0V)
5
AN7
IN
Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is
an analog input terminal from the AH sensor circuit, and connected to the A/D converter
built into the LSI.
AH sensor input.
6
AN6
IN
This input is an analog input terminal from the AH sensor circuit, and connected to the
A/D converter built into the LSI.
7-9
AN5-AN3
IN
Heating constant compensation terminal.
10
AN2
IN
Input signal which communicates the door open/close information to LSI.
Door closed; "L" level signal(0V).
Door opened; "H" level signal(-5V).
Signal coming from touch key.
11
AN1
IN
When any one of G8 line keys on key matrix is touched, a corresponding signal will from
P00 - P06 will be input into AN1. When no key is touched, the signal is held at "L" level.
12
AN0
IN
Temperature measurement input: OVEN THERMISTOR.
By inputting DC voltage corresponding to the temperature detected by the thermistor,
this input is converted into temoerature by the A/D converter built into the LSI.
13
P55
OUT
Segment data signals.
The relation between signals and indicators are as follows:
Signal
Segment
P13 ................... P16
P12 ................... P15
P11 ................... P14
P10 ................... P13
P07 ................... P12
P06 ................... P11
P05 ................... P10
P04 ..................... P9
14
P54
OUT
Signal
Segment
P03 ..................... P8
P02 ..................... P7
P01 ..................... P6
P00 ..................... P5
P37 ..................... P4
P36 ..................... P3
P35 ..................... P2
P55 ..................... P1
ß(60Hz)
GND
VP
(ß : INTO signal)
Refer to the touch control panel circuit about the relation between signals and
indicators. Normally, one pulse is output in every synchronized signal (ß) period, and
input to the anode of the fluorescent display.
Oven lamp driving signal. (Square Waveform : 60Hz)
To turn on and off the shut-off relay(RY1). The square
waveform voltage is delivered to the relay(RY1) driving circuit.
Turntable motor driving signal.
H : GND
OFF
To turn on and off relay(RY4). "L" level: During
Turntable ON. "H" level: During Turntable OFF or
L
ON
during the oven is off condition.
Cooling fan motor driving signal.
H. GND
OFF
During
To turn on and off shut-off relay(RY5). "L" level during
cooking
both microwave and convection cooking; "H" level ON
L
otherwise.
Damper motor driving signal.
H : GND
OFF
To turn on and off shut-off relay(RY6).
16.7 msec.
H
L
During cooking
15
P53
OUT
16
P52
OUT
17
P51
OUT
ON
32
L
R-1855A
Pin No.
Signal
I/O
18
P50
OUT
19
P47
OUT
20
P46
OUT
21
P45
OUT
22
P44
OUT
23
P43
OUT
24
P42
IN
25
INT1
IN
Description
Convection motor driving signal.
H. GND
During
OFF
cooking
To turn on and off shut-off relay(RY7). "L" level during
(Convection)
ON
L
CONVECTION; "H" level otherwise.
Hood lamp driving signal.
H : GND
OFF
To turn on and off relay(RY8). "L" level: During Hood
L
ON
lamp ON. "H" level: During Hood lamp OFF.
Hood motor driving signal.
H : GND
OFF
To turn on and off relay(RY9). "L" level: During Hood
L
ON
motor ON. "H" level: During Hood motor OFF.
Hood motor high / low driving signal.
H : GND
OFF
To turn on and off relay(RY10). "L" level: During Hood
L
ON
motor high. "H" level: During Hood motor low.
Timing signal output terminal for temperature measurement(OVEN).
"L" level (GND): Thermistor OPEN timing.
"H" level (-5V): Temperature measuring timing. (Convection cooking)
0.1 sec
Signal to sound buzzer.
A
A: key touch sound.
2 sec
B: Completion sound.
B
C: When the temperature of the oven cavity reaches
1 sec
1 sec
H: GND
the preset temperature in the preheating mode, or
C
L
when the preheating hold time (30 minutes) is elapsed.
Input signal which communicates the damper open/close information to LSI.
Damper opened; "L" level signal(0V:GND).
Damper closed; "H" level signal(-5V).
Signal to synchronize LSI with commercial power source freqency.
This is the basic timing for all real time processing of LSI.
H : GND
L (-5V)
16.7 msec
26
27
P40
RST
IN
IN
28
P71
OUT
Connected to VC.
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily
set to "L" level the moment power is applied, at this time the LSI is reset. Thereafter set
at "H" level.
Magnetron high-voltage circuit driving signal.
VARI-MODE
ON TIME
OFF TIME
To turn on and off the cook
P-HI (100% power)
32 sec.
0 sec.
relay(RY2). In P-HI operation, the
P-90 (approx. 90% power)
30 sec.
2 sec.
signals holds "L" level during miP-80 (approx. 80% power)
26 sec.
6 sec.
crowave cooking and "H" level
P-70 (approx. 70% power)
24 sec.
8 sec.
while not cooking. In other cooking
P-60 (approx. 60% power)
22 sec.
10 sec.
modes (P-90,P-80,P-70,P-60,PP-50 (approx. 50% power)
18 sec.
14 sec.
50,P-40,P-30,P-20,P-10,P-0) the
P-40 (approx. 40% power)
16 sec.
16 sec.
signal turns to "H" level and "L"
P-30 (approx. 30% power)
12 sec.
20 sec.
level in repetition according to the
P-20 (approx. 20% power)
8 sec.
24 sec.
power level.
P-10 (approx. 10% power)
P-0 (0% power)
29
P70
OUT
30
XIN
IN
6 sec.
0 sec.
26 sec.
32 sec.
Heating element driving signal.
To turn on and off shut-off relay(RY3). "L" level during convection cooking; "H" level
otherwise. During convection cooking, the signal becomes
H. GND
During
OFF
cooking
"H" level when the temperature of the oven cavity exceeds
(Convection)
ON
L
the predetermined temperature.
Internal clock oscillation frequency setting input.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit with
respect to XOUT terminal.
33
R-1855A
Pin No.
31
Signal
XOUT
I/O
OUT
32
VSS
IN
33
P27
IN
34
P26
IN
35
P25
IN
36
P24
IN
P23-P20
OUT
37-40
Description
Internal clock oscillation frequency control output.
Output to control oscillation input of XIN.
Power source voltage:-5V.
VC voltage of power source circuit input.
Signal coming from touch key.
When any one of G12 line keys on key matrix is touched, a corresponding signal will
be input into P27. When no key is touched, the signal is held at "L" level.
Signal similar to AN1.
When any one of G11 line keys on key matrix is touched, a corresponding signal will
be input into P26.
Signal similar to P27.
When any one of G10 line keys on key matrix is touched, a corresponding signal will
be input into P25.
Signal similar to P27.
When any one of G9 line keys on key matrix is touched, a corresponding signal will be
input into P24.
Digit selection signal.
H
The relationship between digit signal and digit are as ß(60Hz)
L
follows;
GND
Digit signal
Digit
P14 ........................... 1st.
P15 .......................... 2nd.
P16 .......................... 3rd.
P17 ........................... 4th.
Digit signal
Digit
P20 .......................... 5th.
P21 .......................... 6th.
P22 .......................... 7th.
P23 .......................... 8th.
P14
VP
P15
P16
P17
(ß : INTO signal)
Refer to the touch control panel circuit about the rela- P21
tion between signals and digits. Normally, one pulse is P22
output in every synchronized signal (ß) period, and
P23
input to the grid of the fluorescent display.
Digit selection signal.
Signal similar to P23.
Segment data signal.
Signal similar to P55.
Segment data signal.
Signal similar to P55.
Segment data signal.
Signal similar to P55.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input
terminal while one of G7 line keys on key matrix is touched.
Segment data signal.
Signal similar to P55.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input
terminal while one of G6 line keys on key matrix is touched.
Segment data signal.
Signal similar to P55.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input
terminal while one of G5 line keys on key matrix is touched.
Segment data signal.
Signal similar to P55.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input
terminal while one of G4 line keys on key matrix is touched.
Segment data signal.
Signal similar to P55.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input
terminal while one of G3 line keys on key matrix is touched.
Segment data signal.
Signal similar to P55.
P20
41-44
45-48
49
50
51
52
53
54
55
P17-P14
P13-P10
P07
P06
P05
P04
P03
P02
P01
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
34
to AN1 and P27 - P24
to AN1 and P27 - P24
to AN1 and P27 - P24
to AN1 and P27 - P24
to AN1 and P27 - P24
R-1855A
Pin No.
Signal
56
57-59
60-64
I/O
P00
OUT
P37-P35
P34-P30
OUT
OUT
Description
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN1 and P27 - P24
terminal while one of G2 line keys on key matrix is touched.
Segment data signal.
Signal similar to P55.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN1 and P27 - P24
terminal while one of G1 line keys on key matrix is touched.
Segment data signal.
Signal similar to P55.
Used for initial balancing of the bridge circuit (absolute humidity sensor).
ABSOLUTE HUMIDITY SENSOR CIRCUIT
(1) Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed in
the closed glass tube filled with dry air while another in
the open glass tube. Each sensor is provided with the
protective cover made of metal with holes to be protected
from the external airflow.
With this voltage given, the switches SW1 to SW5 in the
LSI are turned on in such a way as to change the
resistance values in parallel with R50-1. Changing the
resistance values results in that there is the same
potential at both F-3 terminal of the absolute humidity
sensor and AN7 terminal of the LSI. The voltage of AN6
terminal will indicate about -2.5V. This initial balancing
is set up about 16 seconds after the unit is put in the
Sensor Cooking mode. As the sensor cooking proceeds,
the food is heated to generate moisture by which the
resistance balance of the bridge circuit is deviated to
increase the voltage available at AN6 terminal of the LSI.
Then the LSI observes that voltage at AN6 terminal and
compares it with its initial value, and when the comparison
rate reaches the preset value (fixed for each menu to be
cooked), the LSI causes the unit to stop sensor cooking;
thereafter, the unit goes in the next operation
automatically.
After 16 seconds of operation in the sensor cook mode,
the LSI detects the initial voltage at AN6. If the absolute
humidity sensor is open or shorted, the circuit can not
be balanced for initial voltage comparisons. This will
result in the word "error" on the display and the cooking
operation is stopped.
Sensing part
(Open glass tube)
(2) Operational Principle of Absolute Humidity Sensor
The figure below shows the basic structure of an
absolute humidity sensor. A bridge circuit is formed by
two thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
Each thermistor is supplied with a current to keep it
heated at about 150OC (302OF), the resultant heat is
dissipated in the air and if the two thermistors are placed
in different humidity conditions they show different
degrees of heat conductivity leading to a potential
difference between them causing an output voltage from
the bridge circuit, the intensity of which is increased as
the absolute humidity of the air increases. Since the
output is very minute, it is amplified by the operational
amplifier.
S
R3
R2
S : Thermistor
open vessel
C : Thermistor
closed vessel
Absolute humidity vs,
output voltage characterist
C. Thermistor in
closed vesssl
S. Thermistor in
open vessel
11
F-1
C
F-3
3.57k
0.1
uF
(3) Detector Circuit of Absolute Humidity Sensor Circuit
This detector circuit is used to detect the output voltage
of the absolute humidity circuit to allow the LSI to control
sensor cooking of the unit. When the unit is set in the
sensor cooking mode, a 16 seconds clearing cycle
occurs. Then the detector circuit starts to function and
the LSI observes the initial voltage available at its AN6
terminal.
S
3.32k 1.8k
10
R51
F-2
VA : -15V
35
64
5
63
300k
6
62
150k
7
61
75k
8
60
3
5
37.4k
47k
Absolute humidity (g/m 2 )
4
+
10k
360k
9
VA : -15V
P31
P32
P33
P34
1
VC : -5V
SW2
SW3
SW4
SW5
AN7
LSI
(IC1)
2
47k
12
SW1
P30
0.01uF
-
620k
0.01uF
Operational
R1 amplifier
Output
voltage
+
IC2(IZA495DR)
Output voltage
C
1) Absolute humidity sensor circuit
0.015uF
Sensing part
(Closed glass tube)
6
AN6
R-1855A
SERVICING
B. On some models, the power supply cord between the
touch control panel and the oven proper is long enough
that they may be separated from each other. For those
models, therefore, it is possible to check and repair the
controls of the touch control panel while keeping it apart
from the oven proper; in this case you must short both
ends of the door sensing switch (on PWB) of the touch
control panel with a jumper, which brings about an
operational state that is equivalent to the oven door being
closed. As for the sensor-related controls of the touch
control panel, checking them is possible if dummy
resistor(s) with resistance equal to that of the controls
are used.
(2) Servicing the touch control panel with power supply
from an external power source:
Disconnect the touch control panel completely from the
oven proper,and short both ends of the door sensing
switch (on PWB) of the touch control panel,which brings
about an operational state that is equivalent to the oven
door being closed. Connect an external power source to
the power input terminal of the touch control panel, then
it is possible to check and repair the controls of the touch
control panel it is also possible to check the sensorrelated controls of the touch control panel by using the
dummy resistor(s).
1. Precautions for Handling Electronic Components
This unit uses CMOS LSI in the integral part of the
circuits. When handling these parts, the following precautions should be strictly followed. CMOS LSI have
extremely high impedance at its input and output terminals. For this reason, it is easily influenced by the
surrounding high voltage power source, static electricity
charge in clothes, etc, and sometimes it is not fully
protected by the built-in protection circuit.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them in
aluminium foil. Also wrap all PW boards containing them
in aluminium foil.
2) When soldering, ground the technician as shown in the
figure and use grounded soldering iron and work table.
approx. 1M ohm
2. Shapes of Electronic Components
E
C
B
Transistor
2SB1238
E
CB
Transistor
DTA123ES
KRA101M
KRC101M
KRC243M
4. Servicing Tools
Tools required to service the touch control panel assembly.
1) Soldering iron: 30W
(It is recommended to use a soldering iron with a
grounding terminal.)
2) Oscilloscope: Single beam, frequency range: DC 10MHz type or more advanced model.
3) Others: Hand tools
3. Servicing of Touch Control Panel
We describe the procedures to permit servicing of the
touch control panel of the microwave oven and the
precautions you must take when doing so. To perform the
servicing, power to the touch control panel is available
either from the power line of the oven itself or from an
external power source.
(1) Servicing the touch control panel with power supply
of the oven:
CAUTION:
THE HIGH VOLTAGE TRANSFORMER OF THE MICROWAVE OVEN IS STILL LIVE DURING SERVICING
PRESENTS A HAZARD.
Therefore, when checking the performance of the touch
control panel, put the outer cabinet on the oven to avoid
touching the high voltage transformer, or unplug the
primary terminal (connector) of the high voltage transformer to turn it off; the end of such connector must be
insulated with an insulating tape. After servicing, be sure
to replace the leads to their original locations.
A. On some models, the power supply cord between the
touch control panel and the oven itself is so short that the
two can't be separated.
For those models, check and repair all the controls
(sensor-related ones included) of the touch control panel
while keeping it connected to the oven.
5. Other Precautions
1) Before turning on the power source of the control unit,
remove the aluminium foil applied for preventing static
electricity.
2) Connect the connector of the key unit to the control unit
being sure that the lead wires are not twisted.
3) After aluminium foil is removed, be careful that abnormal
voltage due to static electricity etc. is not applied to the
input or output terminals.
4) Attach connectors, electrolytic capacitors, etc. to PWB,
making sure that all connections are tight.
5) Be sure to use specified components where high precision is required.
36
R-1855A
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
WARNING AGAINST HIGH VOLTAGE:
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may
result in severe, possibly fatal, electric shock.
(Example)
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Avoid possible exposure to microwave energy. Please follow the instructions below before operating
the oven.
1. Disconnect the power supply cord.
2. Visually check the door and cavity face plate for
6. There are defective parts in the microwave generating
damage (dents, cracks, signs of arcing etc.).
and transmission assembly.
7. There is visible damage to the oven.
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven:
Do not operate the oven if any of the following conditions
1. Without the RF gasket (Magnetron).
exist;
2. If the wave guide or oven cavity are not intact.
1. Door does not close firmly.
3. If the door is not closed.
2. Door hinge, support or latch hook is damaged.
4. If the outer case (cabinet) is not fitted.
3. The door gasket or seal is damaged.
4. The door is bent or warped.
5. There are defective parts in the door interlock system.
WARNING:
WARNING FOR WIRING
To prevent an electric shock, take the following precautions.
1. Before wiring,
1) Disconnect the power supply cord.
2) Open the door block it open.
3) Discharge the high voltage capacitor and wait for 60
seconds.
2. Don’t let the wire leads touch to the following parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, High voltage transformer
and Oven cavity.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector until its pin is locked
and make sure that the wire leads do not come off even
if the wire leads are pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANEL PARTS, DOOR PARTS’, when carrying out any of
the following removal procedures:
THE FOLLOWING ADJUSTMENTS OR COMPONENT REPLACEMENT CAN BE PERFORMED
WITHOUT REMOVING THE OVEN FROM THE WALL
1. Hood lamps, sockets and grease filter.
2. Oven lamp, base cover and hood lamp glass assembly.
3. Turntable motor.
4. Hood exhaust louver.
5. Control panel assembly or components
6. Stirrer cover and stirrer fan.
HOOD EXHAUST LOUVER REMOVAL
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the one (1) screw holding the hood exhaust
louver to the oven cavity with the outer case cabinet.
4. Pull the hood exhaust louver from the oven cavity by
pushing the right and left tabs of the hood exhaust louver
to remove.
5. Now, the hood exhaust louver is free.
Push
Hood exhaust
louver
Tab (left )
Push
Tab (right)
37
R-1855A
REMOVAL OF OVEN FROM WALL (Two persons recommended to remove the oven)
1. Disconnect the power supply cord, and uncoil the power
supply cord.
2. Remove the turntable tray and support from the oven
cavity.
3. Remove the two (2) screws holding the oven (outer case
cabinet) to the top cabinet.
4. Remove the two (2) grease filters from the base cover.
5. While supporting the front of the oven, unfasten the two (2)
unit mounting screws holding the oven to the unit mounting
plate.
6. Lower the front of the oven and pull the power cord out of
the wall cabinet.
7. Lift the oven up off the hooks at the bottom of the mounting
plate.
8. The oven is now free and can be placed on the work
surface selected for servicing the oven.
9. Installation is the reverse of this procedure.
OUTER CASE REMOVAL
Remove the oven from the wall and proceed as follows;
1. Disconnect the power supply cord.
2. Open the door block it open.
3. Remove one (1) screw holding the hood exhaust louver to
the oven, and pull it forward to remove by pushing the right
and left tabs of the hood exhaust louver. (Refer to
procedure of "HOOD EXHAUST LOUVER REMOVAL".)
4. Remove four (4) screws holding the rear stay to the hood
fan motor or the oven, and remove it.
5. Remove the four (4) screws from the rear of the outer case
cabinet.
6. Slide the outer case cabinet back about 1 inch (3 cm) to
free it from retaining clips on the cavity face plate.
7. Disconnect the three (3) pin connector of the power supply
cord from the wiring harness and remove the power supply
cord together with the outer case.
8. Discharge high voltage capacitor.
CAUTION: 1. DISCONNECT OVEN FROM POWER
SUPPLY BEFORE REMOVING OUTER
CASE.
2. DISCHARGE THE HIGH VOLTAGE
CAPACITOR BEFORE TOUCHING ANY
OVEN COMPONENTS OR WIRING.
UNIT MOUNTING SCREW AND HOOD INTAKE DUCT R REMOVAL
6. Remove the three (3) screws holding the hood intake duct
R to the base plate right, fan duct and the oven cavity.
7. Slide the hood intake duct R out of the right side of the
oven.
8. Now the hood intake duct R is free
9. Discharge the high voltage capacitor.
1. Disconnect the power supply cord and remove the oven
from the wall and remove the outer case of the oven.
2. Open the door block it open.
3. Bend the tab of the oven cavity back plate.
4. Lift the unit mounting screw off the tab.
5. Slide down it from the base plate right. Now , the unit
mounting screw is free.
POWER TRANSFORMER REMOVAL
plate right.
Re-install
1. Rest the transformer on the base plate right with its
primary terminals toward the control panel.
2. Secure the transformer with two (2) screws to base plate
right.
3. Re-connect wire leads (primary and high voltage) to the
transformer and filament leads of transformer to magnetron
and high voltage capacitor. Refer to "PICTORIAL
DIAGRAM".
4. Re-install the hood intake duct R, and the outer case and
5. check that oven is operating properly.
CAUTION: MAKE SURE THE WIRE LEADS NEVER TOUCH
THE FAN BLADE.
1. Disconnect the power supply cord and remove the oven
from wall, remove outer case, remove the unit mounting
screw and hood intake duct R. (Refer to procedure of
"Removal of Oven from Wall", "Outer Case Removal" and
"Unit Mounting Screw and Hood Intake Duct R Removal".)
2. Open the door block it open.
3. Discharge high voltage capacitor.
4. Disconnect filament leads of transformer from the
magnetron and capacitor.
5. Disconnect high voltage leads of capacitor from the
transformer.
6. Disconnect wire leads from transformer.
7. Remove two (2) screws holding the transformer to base
HOOD FAN MOTOR, HOOD EXHAUST DUCT AND OVEN LAMP SOCKET AND AH SENSOR REMOVAL
1. Disconect the power supply and remove the oven from
wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open
3. Disconnect the 6-pin connector of the hood fan motor from
the main wire harness located at the right edge of the hood
exhaust duct.
4. Disconnect the connector CN-F from the control unit.
5. Remove three (3) screws holding the hood exhaust duct
to the oven cavity.
6. Remove two (2) screws holding the hood exhaust duct to
the exhaust duct.
7. Release the 6-pin connector and the 3-pin connector of the
main harness A from the hood exhaust duct.
8. Release the one (1) snap band of the main harness A from
the left edge of the hood exhaust duct.
9. Release the snap band of the wire cord of the hood fan
motor from the hood exhaust duct.
38
R-1855A
10.Now, the hood fan motor is free.
11.Remove the hood exhaust duct from the oven cavity by
lifting it up
12.Screw the oven lamp off from the lamp socket.
13.Remove the lamp socket from the lamp angle of the top
duct by releasing the two (2) tabs of the oven lamp socket.
14.Pull the wire leads from the oven lamp socket by pushing
the terminal hole of the oven lamp socket with the small
flat type screw driver.
15.Now, the oven lamp socket is free.
16.Release the one (1) snap band of the AH sensor
assembly from the oven cavity.
17.Release the one (1) tab of the top duct from the AH
sensor assembly.
18.Remove two (2) screws holding the AH sensor assembly
to the exhaust duct.
19.Now, the AH sensor assembly and the exhaust duct are
free.
Oven lamp
socket
Terminal
Wire lead
Terminal hole
Flate type small
screw driver
MAGNETRON REMOVAL
1. Disconnect the power supply cord, remove the oven from
wall, remove outer case, remove the unit mounting screw
and hood intake duct R. (Refer to procedure of "Removal
of Oven from Wall", "Outer case Removal" and "Unit
Mounting Screw and Hood Intake Duct R Removal".)
2. Open the door block it open.
3. Discharge high voltage capacitor.
4. Remove the hood fan motor and the hood exhaust duct
from the oven cavity, referring to the procedure of
"HOOD FAN MOTOR, HOOD EXHAUST DUCT, OVEN
LAMP SOCKET AND AH SENSOR REMOVAL".
5. Disconnect the high voltage wire leads of the high voltage
rectifier assembly from the magnetron.
6. Disconnect the filament lead of the transformer from the
magnetron.
7. Carefully remove the four (4) mounting screws holding the
magnetron to waveguide. When removing the screws hold
the magnetron to prevent it from falling.
8. Remove the magnetron from the unit with care so the
magnetron tube should not hit by any metal object around
the tube.
CAUTION: WHEN REPLACING THE MAGNETRON, BE
SURE THE R.F. GASKET IS IN PLACE AND
MOUNTING SCREWS ARE TIGHTENED SECURELY.
HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL
1. Disconnect the power supply cord, remove the oven
from wall, remove outer case, remove the unit mounting
screw and hood intake duct R. (Refer to procedure of
"Removal of Oven from Wall", "Outer case Removal"
and "Unit Mounting Screw and Hood Intake Duct R
Removal".)
2.
Open the door block it open.
3. Discharge high voltage capacitor.
4. Disconnect the high voltage wire leads with high voltage
rectifier from the magnetron.
5. Disconnect filament lead of the transformer from high
voltage capacitor.
6. Disconnect high voltage wire lead of capacitor from the
transformer.
7. Remove one (1) screw holding capacitor holder to the
back plate.
8. Remove one (1) screw holding high voltage rectifier from
the capacitor holder.
9. Disconnect the high voltage rectifier assembly from the
high voltage capacitor.
10.Now, the high voltage rectifier assembly is free.
11.Remove capacitor from the holder.
12.Now, the high voltage capacitor is free.
CAUTION: WHEN REPLACING THE HIGH VOLTAGE RECTIFIER ASSEMBLY, THE GROUND SIDE TERMINAL MUST BE SECURED FIRMLY WITH A
HOOD FAN THERMAL CUT-OUT REMOVAL
1. Disconnect the power cord, remove the oven from wall
and remove outer case. (Refer to procedure of "Removal
of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the hood fan thermal cutout.
5. Remove the hood fan thermal cut-out from the base plate
right.
6. Now, the hood fan thermal cut-out is free.
TEMPERATURE FUSE (MAGNETRON) REMOVAL
1. Disconnect the power supply cord, remove the oven from
wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge the high voltage capacitor.
4. Remove the hood fan motor and the hood exhaust duct
from the oven cavity, referring to the procedure of "
5. Disconnect the wire leads from the temperature fuse
(Magnetron).
6. Remove the one (1) screw holding the temperature fuse
(Magnetron) to the oven cavity.
7. Now, the temperature fuse (Magnetron) is free.
39
R-1855A
GROUNDING SCREW.
9. Remove one (1) screw holding the fan duct assembly to
oven cavity.
10.Release the fan duct assembly from the oven cavity.
11.Remove the fan blade from the fan motor shaft according
the following procedure.
1) Hold the edge of the rotor of the fan motor by using a pair
of groove joint pliers.
CAUTION:
* Make sure that any pieces do not enter the gap
between the rotor and the startor of the fan motor
because the rotor is easily shaven by pliers and metal
pieces may be produced.
* Do not touch the pliers to the coil of the fan motor
because the coil may be cut or injured.
* Do not disfigure the bracket by touching with the
pliers.
2) Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
3) Now, the fan blade will be free.
CAUTION:
* Do not reuse the removed fan blade because the hole
(for shaft) may be larger than normal.
. Remove the two (2) screws holding the fan motor to the fan
Rear View
COOLING FAN MOTOR REMOVAL
1. Disconnect the power supply cord, remove the oven
from wall and remove outer case, remove the unit
mounting screw and hood intake duct R. (Refer to
procedure of "Removal of Oven from Wall", "Outer case
Removal" and "Unit Mounting Screw and Hood Intake
Duct R Removal".)
2. Open door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood fan motor and the hood exhaust duct
from the oven cavity, referring to the procedure of " HOOD
FAN MOTOR, HOOD EXHAUST DUCT, OVEN LAMP
SOCKET AND AH SENSOR REMOVAL".
5. Discharge high voltage capacitor.
6. Release the two (2) snaps of the magnetron duct from the
oven cavity. And remove the two (2) tabs of the magnetron
duct from the fan duct.
7. Release snap bands of the main harness A installed to the
fan duct and nearest the fan duct.
8. Disconnect the wire leads from the fan motor.
duct.
12.Now, the fan motor is free.
INSTALLATION
1. Install the fan motor to the fan duct with the two (2) screws.
2. Install the fan blade to the fan motor shaft according the
following procedure.
1) Hold the center of the bracket which supports the shaft of
the fan motor on the flat table.
2) Apply the screw lock tight into the hole (for shaft) of the
fan blade.
3) Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
CAUTION:
* Do not hit the fan blade strongly when installed
because the bracket may be disfigured.
* Make sure that the fan blade rotates smooth after
installation.
* Make sure that the axis of the shaft is not slanted.
3. Install the fan duct assembly to the oven cavity with the
one (1) screw.
4. Install the magnetron duct to the fan duct and oven cavity.
5. Connect the wire leads to the fan motor, referring to the
pictorial diagram.
6. Reinstall the released snap bands of the main harness A
to the fan duct and nearest the fan duct.
7. Refer to procedure of "HOOD FAN MOTOR, HOOD
EXHAUST DUCT, OVEN LAMP SOCKET AND AH
SENSOR REMOVAL" and "Unit Mounting Screw and
Hood Intake Duct R Removal" and "Outer case Removal".
And reverse their procedure.
Coil
Groove joint pliers
Stator
Gap
Bracket
Shaft
Axis
Stator
These are the areas
that should be held
with a pliers
Rotor
Side View
Shaft
Table
Rotor
Center of
bracket
40
R-1855A
TURNTABLE MOTOR AND COUPLING REMOVAL
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the three (3) screws holding the base cover to the
oven cavity
4. Remove the base cover from the oven cavity by pulling
down and moving to the left slightly.
5. Disconnect the wire leads from the turntable motor.
6. Remove two (2) screws holding turntable motor to the
oven cavity.
7. Now the turntable motor is free.
8. Pull the coupling out of the turntable motor packing which
is installed on the oven cavity floor.
9. Now the coupling is free.
STIRRER MOTOR REMOVAL
5. Disconnect the wire leads from the stirrer motor.
6. Remove the two (2) screws holding the stirrer motor to the
waveguide of the oven cavity.
7. Remove the stirrer motor from the waveguide.
8. Now, the stirrer motor is free.
9. When install the stirrer motor, the shaft of stirrer motor
must be inserted to the stirrer fan shaft. Refer to the
procedure of "STIRRER COVER AND STIRRER FAN
INSTALLATION".
1. Disconnect the power supply cord.and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood fan motor and the hood exhaust duct
from the oven cavity, referring to the procedure of " HOOD
FAN MOTOR, HOOD EXHAUST DUCT, OVEN LAMP
SOCKET AND AH SENSOR REMOVAL".
STIRRER COVER AND STIRRER FAN INSTALLATION
1. Insert the shaft of stirrer fan to the shaft of stirrer motor.
2. Hold the stirrer fan not to come out from the shaft of stirrer
motor.
3. Insert the cutout of stirrer cover to the tabs on the ceiling.
4. Put the stirrer fan on the stirrer cover to match the stirrer
fan shaft to the center of the stirrer support.
5. Hold the stirrer cover to the oven cavity with the two (2)
screws.
Shaft
Stirrer fan
Stirrer
support
Screws
Stirrer
cover
NOISE FILTER REMOVAL
4. Disconnect the wire leads from the terminals of the noise
filter .
5. Remove one (1) screw mounted into the noise filter
bracket.
1. Disconnect the power supply cord and then remove outer
case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
OVEN LAMP REMOVAL
4. Lift the oven lamp cover up.
5. Now, the oven lamp and the socket are found.
6. Screw the oven lamp off from the lamp socket.
7. Now, the oven lamp is free.
NOTE: HOT (ORANGE) WIRE MUST BE CONNECTED
TO THE TERMINAL WITH BLUE MARKING ON
LAMP SOCKET.
1. Disconnect the power supply cord.
2. Remove one (1) screw holding the hood exhaust louver to
oven cavity front flange.
3. Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER
REMOVAL")
CONTROL PANEL ASSEMBLY, CONTROL UNIT AND KEY UNIT REMOVAL
plate by lifting it up.
8. Disconnect the wire leads from the relays RY1, RY2 and
RY3.
9. Disconnect the connectors CN-A, CN-B CN-C, CN-E and
CN-F from the control unit.
10. Remove the control panel assembly from the oven.
11.Now, the control panel assembly is free.
12.Remove four (4) screws holding the control unit to the
control panel.
13.Release the two (2) tabs holding the control unit to the
control panel.
14.Now, the control unit is free.
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove one (1) screw holding the hood exhaust louver to
oven cavity front flange.
4. Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER
REMOVAL")
5. Open the oven door.
6. Remove one (1) screw holding the control panel to the
oven cavity front face plate.
7. Release the control panel from the oven cavity front face
41
R-1855A
15.Remove the one (1) screw holding the key fixing plate to
the control panel.
16.Release the four (4) tabs holding the key fixing plate to the
control panel.
17.Remove the key fixing plate from the control panel.
18.Tear the key unit from the key fixing plate.
19.Now, the key unit is free
4. Insert the bottom edge of the display board under the tab
of control panel as shown in step 4.
5. PLace the top edge of the display board on the clip (F).
And press the display board downward as shown in step
4. (Holes in middle of display board should be positioned
into locator pins.)
6. After installing display board, press the CPU downward
90O until CPU is locked into place by the clips.
7. Hold the CPU with the four (4) screws.
8. After installing CPU, make sure jumper wires are not
bent, touching or broken.
NOTES FOR KEY UNIT REPLACEMENT
1. Do not reuse the torn key unit because the performance
of the adhesive becomes weak.
2. Before attaching a new key unit, wipe off remaining
adhesive on the key fixing plate surfaces completely with
a soft cloth soaked in alcohol.
3. When attaching the key unit to the key fixing plate, adjust
the upper edge and right edge of the key unit to the correct
position of key fixing plate.
4. Stick the key unit firmly to the key fixing plate by rubbing
with soft cloth not to scratch.
Top edge of the display board
Display
Board
NOTES FOR NEW CONTROL UNIT REPLACEMENT
c
1. Before installation of the new CPU into the control panel,
grasp the middle section between thump and finger, bend
the display board forward a until "b" breaks as shown in
step 1.
2. To remove the middle section push both sides of the
middle section towards "d" until "c" breaks as shown in
step 2.
NOTE: Discard the middle section.
3. After removing the middle section, bend the display
board 90O, positioning the jumper wires into the notches
of the display board as shown in step 3.
a
b
Middle
section
LSI
Control Unit
CN-G
b
Middle
Section
Jumper
wires
c
Jumper
wires
d
Notches
STEP 1
STEP 2
Control
panel
Clip (F)
Clip (E)
STEP 3
Locator pin
STEP 4
POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL
Terminal
1. Disconnect the power supply cord.and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Pull down on the positive lock® connector.
5. Push the lever of positive lock®
Positive lock®
connector
1
Push
Lever
CAUTION: WHEN CONNECTING THE POSITIVE LOCK®
CONNECTORS TO THE TERMINALS, INSTALL
THE POSITIVE LOCK® SO THAT THE LEVER
FACES YOU.
2
Pull down
Positive lock®connector
42
Break
point
R-1855A
CONVECTION DUCT ASSEMBLY REMOVAL
1. Disconnect power supply cord, remove the oven from
wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Lift the left mounting screw off the tab and slide it down
from the base plate left.
5. Remove the one (1) screw holding the exhaust duct to the
top duct.
6. Remove the exhaust duct from the oven cavity.
7. Remove the heat protect top sheet from the top duct.
8. Remove the two (2) screws holding the hood intake duct
L to the heater cover L and the oven cavity front flange.
9. Disconnect the wire leads from the convection motor
and heater element.
10.Disconnect the connector of the main wire harness A
from the connector of the thermistor.
NOTE: After installed the heating element completely,
bent top of the heating element holder to inside
using by long nose pliers as shown following
illustration.
Long nose plier
Heating
element
Heating element
holder
CONVECTION FAN AND MOTOR REMOVAL
THERMISTOR REMOVAL
18.Remove one (1) nut (turn to clockwise), spring washer and
washer holding the convection fan to the convection
motor shaft.
19.Now, the convection fan is now free.
20.Remove two (2) washers and pipe holding the convection
motor fan to convection motor shaft.
21.Remove two (2) screws holding the convection motor
mounting plate to convection duct.
22.Remove the convection motor assembly, convection
motor fan and one (1) washer from the convection duct.
23.Remove the convection motor fan and one (1) washer
holding the fan to convection motor shaft.
24.Remove the E-ring from the convection motor shaft.
25.Remove two (2) screws holding the convection motor to
convection motor mounting plate.
26.Now, the convection motor is free.
11.Remove one (1) screw holding the thermistor to the
convection duct.
12.Now, the thermistor is now free.
CONVECTION HEATER REMOVAL
13.Remove six (6) oven side screws holding the convection
duct to the oven cavity.
14.Remove two (2) screws holding the convection duct to the
oven cavity top side.
15.Remove two (2) screws holding the two heater mounting
holders to the convection duct.
16.Remove two (2) screws holding the convection heater to
the convection duct.
17.Now, the convection heater is now free.
DAMPER MOTOR AND DAMPER SWITCH REMOVAL
2. Open the door and block it open.
3. Discharge the high voltage capacitor.
4. Disconnect wire leads from damper motor and damper
switch.
5. Remove one (1) screw holding damper motor to damper
motor angle and bend the tab holding damper switch to
damper motor angle.
6. Damper motor and switch are free.
1. Disconnect the power supply, remove the oven from
wall, remove outer case, remove the unit mounting
screw and hood intake duct R. (Refer to procedure of
"Removal of Oven from Wall", "Outer case Removal"
and "Unit Mounting Screw and Hood Intake Duct R
Removal".)
DOOR SENSING SWITCH, SECONDARY INTERLOCK SWITCH, THIRD DOOR SWITCH AND MONITOR
SWITCH REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood fan motor and the hood exhaust duct
from the oven cavity, referring to the procedure of " HOOD
FAN MOTOR, HOOD EXHAUST DUCT, OVEN LAMP
SOCKET AND AH SENSOR REMOVAL".
5. Remove the control panel assembly, referring to the
procedure of "CONTROL PANEL ASSEMBLY ,
CONTROL UNIT AND KEY UNIT REMOVAL".
6. Bend the tab of the oven cavity face plate which prevent
the open lever from coming out.
7. Remove the open lever from to the oven cavity.
8. Remove the two (2) screws holding the latch hook to the
oven cavity front flange.
9. Remove the latch hook from the oven cavity front flange.
10.Disconnect the wire reads of each switch.
11.Remove each switch from the latch hook with pushing the
one (1) stopper tub holding each switch.
12.Now, each switch is free.
Re-install
1. Re-install open lever and each switch in its place. The
43
R-1855A
3. Secure the latch hook (with two (2) mounting screws) to
oven cavity front flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit. Refer to
chapter "Test Procedure" and "Adjustment procedure".
And install the hood intake duct R, hood exhaust duct
and outer case.
diagram.
DOOR SENSING SWITCH, SECONDARY INTERLOCK, THIRD DOOR SWITCH AND MONITOR SWITCH ADJUSTMENT
If the door sensing switch, secondary interlock switch, third
door switch and monitor switch do not operate properly due
to a misadjustment, the following adjustment should be
made.
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
5. With door closed, adjust latch hook by moving it back and
forth, and up and down. In and out play of the door allowed
by the upper and lower position of the latch hook should
be less than 0.5mm. The vertical position of the latch hook
should be adjusted so that the door sensing switch,
secondary interlock switch and third door switch are
activated with the door closed. The horizontal position
of the latch hook should be adjusted so that the monitor
switch is activated with the door closed.
6. Secure the screws with washers firmly.
7. Check the all switches operation. If the any switch has not
activated with the door closed, loosen screw and adjust
the latch hook position.
and third door switch interrupt the circuit before the door
can be opened.
3. Monitor switch contacts close when door is opened.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
LATCH HOOK
LATCH
HEADS
DOOR SENSING
SWITCH
MONITOR FUSE
MONITOR
SWITCH
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm when
in the latched position. First check upper position of latch
hook, pushing and pulling upper portion of door toward
the oven face. Then check lower portion of the latch
hook, pushing and pulling lower portion of the door
toward the oven face. Both results (play in the door)
should be less than 0.5mm.
2. The door sensing switch, secondary interlock switch
THIRD
DOOR
SWITCH
DOOR
OPEN LEVER
SECONDARY
INTERLOCK
SWITCH
Figure C-1. Latch Switch Adjustments
DOOR REPLACEMENT
DOOR ASSEMBLY REMOVAL
1. Unplug the oven from power outlet and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Remove one (1) screw holding the hood exhaust louver
to the oven cavity with outer case cabinet, as shown in
Figure C-2.
3. Remove the hood exhaust louver from the oven cavity
by pushing right and left tabs of the hood exhaust louver,
as shown in Figure C-2.
4. Remove the sash left from the oven cavity from face
plate by lifting it up.
5. Push the door open button and open the door slightly.
6. Insert an putty knife (thickness of about 0.5mm) into the
gap A between the door stopper and the choke cover as
shown in Figure C-3 to free engaging parts.
7. Lift up the door stopper.
8. Now, the door stopper is free from the door assembly.
9. Lift up the door assembly to release the upper and lower
door hinge pins from the upper and lower oven hinges.
10.Now, the door assembly is free.
Note:
When the individual parts are replaced, refer to
"Door Disassembly".
DOOR ASSEMBLY RE-INSTALL
1. On re-installing door, insert the lower oven hinge to lower
door hinge pin.
2. Insert the upper oven hinge to the upper door hinge pin.
3. Shut the door (close the contacts of interlock switches).
4. Make sure upper and lower oven hinges are inserted into
the upper an lower door hinge pins.
5. Make sure the door is parallel with oven face lines (left and
upper side lines) and door latch heads pass through latch
holes correctly.
44
R-1855A
microwave energy from oven cavity during cook
cycle. This function does not require that door be
air-tight, moisture (condensation)-tight or lighttight. Therefore, occasional appearance of
moisture, light or sensing of gentle warm air
movement around oven door is not abnormal
and do not of themselves, indicate a leakage of
microwave energy from oven cavity.
6. Re-install the door stopper to the door assembly.
7. Re-install the sash left to the oven cavity front face plate.
8. Re-install the hood exhaust louver to the oven cavity front
face plate.
Note: After any service to the door;
(A) Make sure that door sensing switch and secondary
interlock switch are operating properly. (Refer to
chapter "Test Procedures".)
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
Tab
Hood Exhaust Louver
Upper Door
Hinge Pin Upper
Oven
Hinge
After any servicing, make sure of the following :
1. Door latch heads smoothly catch latch hook through latch
holes and that latch head goes through center of latch
hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity face
plate.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Tab
RE-INSTALL
Lower
Oven
Hinge
Door
Assembly
Door
Stopper
Lower Door
Hinge Pin
Latch
Heads
Note: The door on a microwave oven is designed to act
as an electronic seal preventing the leakage of
RE-INSTALL
Figure C-2. Door Replacement and adjustment
DOOR DISASSEMBLY
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood exhaust louver from the oven cavity by
pushing the right and left tabs of the hood exhaust louver.
(Refer to the procedure of "HOOD EXHAUST LOUVER
REMOVAL".)
5. Remove door assembly, refer to "Door Replacement".
Replacement of door components are as follows:
6. Place door assembly on a soft cloth with latches facing
up.
Note: As the engaging part of choke cover and door panel
are provided at 17 places, do not force any particular part.
LATCH SPRING, LATCH HEAD AND DOOR PANEL
13.Lease the latch spring from the tab of the latch head and
tab of the door panel.
14.Release the latch head from the door panel.
15.Now, the latch spring, latch head and door panel are free.
Door stopper
A
7
Choke Cover
8
6
9
5
4
Bent
CHOKE COVER
7. Insert an putty knife (thickness of about 0.5mm) into the
gap between the choke cover and door panel and between
the choke cover and the door frame as shown Figure C3 to free engaging parts.
8. Try the principles of the lever and lift up the choke cover
by inserting a putty knife in order shown in Figure C-3.
9. Now choke cover is free from door panel and door frame.
1
3
10
2
11
17
13
Choke Cover
15
14
DOOR FRAME
10.Remove six (6) screws holding the door panel to the door
frame assembly.
11.Release the door frame assembly from the door panel.
12.Now, door frame assembly is free.
Putty Knife
12
16
Door Frame
Figure C-3. Door Disassembly
DOOR GLASS FRONT
11.Remove the glass stopper from the door frame.
12.Release the door glass front from the long tab of the door
frame.
13.Now, the door glass front is free.
45
1
PNK
WHT
BRN
2 GRN
N.O.
GRN
YLW 5 RED
BLK
3 BLK
RED 4 YLW
BLU 3 WHT
PPL 2 BLK
GRY 1 BLU
WHT
2 WHT
1 GRN
STIRRER MOTOR
PNK
GRN
COM.
Power Supply
cord 120V 60Hz
TEMPERATURE FUSE (MG.)
R
E
D
BLK
DOOR SENSING SWITCH
WHT
GRN
RY2:Primary Interlock Relay
GRN
Y
L
W
O
R
G
B
R
N
2
2
to oven cavity
front flange
R-1855A
HOOD FAN MOTOR
6
BLK
1
BLK
A
5
4
3
B
BLK
C
1
CN-E
6
D
E
F
G
H
AH. SENSOR
3 WHT
CN-F 2 RED
1 BLK
THERMAL
CUT-OUT
CONVECTION
MOTOR
ORG
GRN
BLK
PPL
RY3 N.O.
WHT
THERMISTOR
BLU
WHT
COM.
RY4
46
DAMPER
SWITCH
RY7
BRN
CN-A
DAMPER
MOTOR
BRN
8
7
PPL
MAGNETRON
ORG
HIGH VOLTAGE
CAPACITOR
4
4
9
HIGH VOLTAGE COMPONENTS
N.O.
WHT
CN-B
2 BLK
1 BLK
3
3
BLK
BRN
RY5
BLK
RED
GRY
N.O.
RY8
RY6
OVEN LAMP & SOCKET
WHT
CN-F
T1
RY10
ORG
WHT
BRN
COM.
RY1
RY9
RED
ORG
MONITOR
FUSE AND
FUSE HOLDER
PPL
COM.
RY2 N.O.
CN-C
Blue
Marking
RED
COM.
CN-E
YLW
RED
CN-G
CN-F
HEATING
ELEMENT
GRY
IC1
BLU
6
CN-C
5
4
3
F
BLU
BLK
GRY
BLK
WHT
2
1
7
BLK
PNK
N.C.
POWER TRANSFORMER
PPL
2
RED
RED
RED
PPL
5
5
CN-B
WHT
ORG
COM.
MONITOR
SWITCH
BLU
H.V.
RECTIFIER
FAN
MOTOR
BLU
GRY
6
5
4
3
FA
GRY 2 GRY-GRY
PNK 1 BRN-BRN
1 WHT
N.O.
5 ORG
4
NOISE FILTER
BOARD
CN-A
3 YLW
2
1 RED
THIRD
DOOR
SWITCH
BLK
COM.
SECONDARY
INTERLOCK
SWITCH
YLW
ORG
R
E
D
B
L
K
B P
R N
N K
P
N
K
TURNTABLE
MOTOR
B
R
N
BLK
COM.
GRY
GRY
BRN
BRN
NOISE
RESISTOR
Blue Marking
6
6
RED
HOOD LAMPS
& SOCKETS
WHT
N.O.
HOOD FAN
THERMAL
CUT-OUT
Figure S-1. Pictorial Diagram
A
B
C
D
E
F
G
H
C7
R7 4.7k
C6 10µ/35v
C8
R8 4.7k
C9
0.1µ/50v
D28
5
RY3
Q28 KRA101M
NO
D29
CONVECTION
HERTER
COM
R30 15k
D32
COM
R31 4.7k
R62 36kF
C60
Q60
KRC101M
CF1 4MHz
(A)
(B)
Q29 KRA101M
5
6
7
8
9
10
11
12
13
15
16
17
18
19
20
22
23
24
25
26
27
28
29
1G
2G
3G
4G
5G
6G
7G
8G
R93 100k
R91 100k
R92 100k
G2
G3
G4
G5
G6
R82 3.3k
D76
R81
D75 3.3k
D74 3.3k
3.3k
D73
R80
R79
R78 3.3k
D72
D71
R77 3.3k
D70
G1
G7
CUSTOM SENSOR
REHEAT
HELP
COMPU SENSOR
MINUTE
POPCORN DEFROST
PLUS
COOK
COMPU
BROIL
G9
CONVEC PREHEAT
LOW MIX HIGH MIX
BAKE
ROAST
COMPU
BAKE
C74 330pF
(C)
G10
BROIL
SLOW
COOK
G11
KITCHEN
TIMER
CLOCK
G12
TURNTABLE POWER
LEVEL
ON / OFF
C72 330pF
C71 330pF
C70 330pF
D30
KG HELP
G8
C73 330pF
D31
MICRO
C50
R70 3.3k
R63 220F R64 3.6kF
R51 4.7k
C30
OZ
COMPU
ROAST
1
2
3
4
5
100˚F
150˚F
275˚F
300˚F
325˚F
6
7
8
9
0
350˚F
375˚F
400˚F
425˚F
450˚F
KEEP
WARM
STOP
CLEAR
START
TOUCH ON
FAN
LIGHT
5
R50 15k
RY2
NO
R75 100k
COM
R76 3.3k
D27
Q30
KRA101M
Q27
KRC243M
(A)
R74 3.3k
+
RY1
–
+
R73 3.3k
–
R72 3.3k
C7
(C) (B)
R71 3.3k
(J7)
(J5)
(J3)
(J6)
(J4)
(J2)
Q26 KRA101M
D26
HOOD MOTOR
C21 0.1µ/50v
RY10
IC1 IZA719DR
D25
Q25 KRA101M
P30
P31
P32
P33
P34
P35
P36
P37
P00
P01
P02
P03
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
P20
P21
P22
P23
P24
P25
P26
P27
COOK LBS
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
12
R100 330 1w
IC2 IZA495DR
1, 2
F
F 31, 32 MIX CONV
4 DEFROST
P1
SENSOR
TURNTABLE ON OFF
(VP)
4
4
VCC
VEE
AVSS
VREF
AN7
AN6
AN5
AN4
AN3
AN2
AN1
AN0
P55
P54
P53
P52
P51
P50
P47
P46
P45
P44
P43
P42
INT1
P40
RST
P71
P70
XIN
XOUT
VSS
RY9
C9
NO
1
RY8
HOOD THERMO
C5
FLUORESCENT DISPLAY TUBE
Q40
KRA101M
RY7
C3
COM
R90 100k
RY6
COM
HIGH
R40 3.3k
Q24 KRA101M
SP40
Q23 KRA101M
C10 0.1µ/50v
Q90 KRA101M
RY5
C20 10µ/35v
47
D20
C1
D21
HOOD LAMP
D22
B7
D23
CONVECTION
MOTOR
Q22 KRA101M
: IF NOT SPECIFIEED, 0.01µF/16v
Q3
KRA101M
RY4
Q21 KRA101M
: IF NOT SPECIFIEED, 1SS270A
(VP)
R3 680 1w
Q20 KRA101M
–
ZD4
HZ4A2
ZD3 HZ5C2
C5 0.1µ/50v
C4 10µ/35v
ZD2
HZ16-1
C3 0.1µ/50v
–
+
R4 510 1/2w
Q1 2SB1238
D24
B5
OVEN LAMP
R1 4.3k
1/2w
C100
+
Q4
DTA123ES
3
3
DAMPER
MOTOR
LOW
–
R2 1.5k
(J1)
D3
+
ZD1
HZ6A3
VRS1
10G471K
a
D2
: IF NOT SPECIFIEED, 1/4w ± 5%
D4
C1 0.1µ/50v
D1
C2 1000µ/35v
3
2
2
B3
1
NOTE
D1-D4 : 11ES1
A3
FAN MOTOR
A
6
A1
B1
B
5
4
c
C
b
TURNTABLE
MOTOR
D
CONTROL UNIT
2
d 1
AC120V
60Hz
MOTOR RUN
CAPACITOR
E
F
G
H
1
T1
A5
KEY UNIT
E1
E2
E3
E4
E5
E6
F1
F2
F3
AH SENSOR
DAMPER
SWITCH
OVEN
THERMISTOR
6
6
DOOR
SWITCH
A
B
C
D
E
F
G
H
R-1855A
Figure S-2. Touch Control Panel Circuit
R-1855A
2
1
4
3
5
6
A
A
R
0
TAPE
B
B
27
28
2
1
32
1
20
21
22
23
24
25
26
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
69
29
30
31
32
33
34
C
1
70
R100
B
C30
32
44
C10
C11
C12
Q40
42
40
41
1
R70
R71
R72
E 38
Q90
43
R93
C5
E
B
39
D
C6
R64
B Q60
ZD4 48
49
51
RY3
E
MICRO
C20
B
B
E
D28
Q30
E
Q27
1
57
52
53
54
55
56
B
B
B
3
12
RY2
58
E
B
AC
(H)
Q3
B
C9
OVEN
LAMP
63
D32
F
Q1
E
C4
66
E
5
H/M
HIGH
B
C1
C3
R1
ZD1
D3
D4
D1
D2
64 E
R3
Q23
D26
7
H/M
LOW
67
Q22
RY1
61
62
C2
B
R2
65
B
E
Q20
ZD2
D25
RY9
D27
Q24
E
Q25
E
Q26
59
9
HOOD
THERMO
CN - C
60
E
CN - F
(JA)
CONV. H
D30
Q29
1
(G)
E
CN - E
R62
D29
6
E
C74
C73
C72
C71
Q28
CN - G
R74
B
R8
B
C2
D31
R63
R50
R51
ZD3
Q4
B
SP40
1
R75
(J6)
(J4)
(J2)
E
CF1
46
E
R40
C50
47
C7
R7
(J8)
45
C60
(C65)
R31
R30
C8
50
R73
(J3)
(J5)
(J7)
(J9)
QKITPB023MRE0
(D65) (R65)
C70
F
33
IC1
R82
D
E
,BFB
R4
R90
R76
R77
R78
R79
R80
R81
C
DIP
64
R91
R92
D70
D71
D72
D73
D74
D75
D76
35
36
37
12
IC2
4
E
RY10
68
1
HOOD
LAMP
D22
D21
RY8
3
5
6
Q21
S1
D23
D24
3
COM
B
S2
P
D20
G
G
2
1
RY4
C100
RY5
RY6
RY7
T1
VRS1
(G)
5
3
(J1)
CN - B
7
CONV DAMP
M
M
1
CN - A
5
FAN.M T T M
AC (N)
3
1
MOTOR
CAPACITOR
H
H
Figure S-3. Printed Wiring Board
1
2
4
3
48
5
6
R-1855A
PARTS LIST
Note: The parts marked “∆” may cause undue microwave exposure.
The parts marked “*” are used in voltage more than 250V. "§" MARK: PARTS DELIVERY SECTION.
REF. NO.
PART NO.
§
DESCRIPTION
Q'TY CODE
ELECTRIC PARTS
*
*
*
*∆
1- 1
1- 2
1- 3
1- 4
1- 5
1- 6
1- 7
1- 8
1- 9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-20
1-21
1-22
1-23
1-24
FH-DZB010MRY0
RC-QZB011MRE0
QFS-TA013WRE0
RHET-A174WRE0
RMOTDA211WRE0
RMOTDA214WRE0
RTHM-0044MRE0
RTRN-B063MRE0
RV-MZA255WRE0
QFSHDB003MRE0
QSW-MA110WRE0
FFS-BA018/KIT
FACCDB011MRE0
QSOCLB006MRE0
FH-HZA053WRE0
QSOCLB006MRE0
FMOTEA362WRK0
RMOTEA343WRE0
RMOTEA344WRE0
RLMPTA077WRE0
FDTCTA171WRK0
RMOTDA217WRE0
RR-WZA031WRE0
FPWBFB014MRK0
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
High voltage rectifier assembly
High voltage capacitor
Temperature fuse 150OC
Convection heater
Turntable motor
Stirrer motor
Thermal cut-out N.O. 60OC
Power transformer
Magnetron
Fuse holder
Sec.interlock,third door,sensing and damper switches
Monitor and sec. interlock switch with fuse assembly
Power supply cord
Hood lamp socket
Thermistor
Oven lamp socket
Hood fan motor
Convection motor
Fan motor
Hood lamp and oven lamp
AH sensor
Damper motor
Noise resistor
Noise filter
2- 1
2- 2
2- 3
2- 4
2- 5
2- 6
2- 6
2- 7
2-7-1
2-7-2
2- 8
2- 9
2-10
PFIL-B002MRE0
PDIF-B011MRF0
GDAI-B052MRP0
GDAI-B039MRP0
GCABUB065MRP0
TMAPCB058MRR0
TMAPCB063MRR0
FANGKB009MRY0
LANGQB016MRP0
PGLSPB004MRE0
PCOVPB051MRE0
HDECQB016MRF0
LSTY-B010MRP0
M
M
M
M
M
M
M
M
M
M
M
M
M
Grease filter
Hood exhaust louver
Base plate right
Base plate left
Outer case cabinet
Schematic diagram (Refer to page 11)
Schematic diagram (Refer to page 13)
Hood lamp glass assembly
Hood lamp glass angle
Hood lamp glass
Base cover
Sash left
Rear stay
1
1
1
1
1
1
2
1
1
1
4
1
1
2
1
1
1
1
1
3
1
1
1
1
AM
AR
AG
AZ
AQ
AQ
AG
AZ
BE
AD
AE
AF
AP
AE
AP
AE
BM
AX
AW
AG
AW
AP
AK
AU
2
1
1
1
1
1
1
1
1
1
1
1
1
AF
AV
AL
AH
BC
AB
AB
AN
AG
AH
AX
AL
AG
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
5
1
BQ
AC
AC
AC
AC
AD
AE
AV
AB
AB
AF
AB
AB
AB
AB
AH
AB
AB
AM
AH
AH
AH
AA
AM
CABINET PARTS
CONTROL PANEL PARTS
3- 1
3- 1A
3- 1B
3- 1C
3- 1D
3- 1E
3- 1F
3- 1G
3- 1H
C1
C2
C3
C4
C5
C6
C7-8
C9-10
C20
C21
C30
C50
C60
C70-74
C100
DPWBFB061MRU0
QCNCMA227DRE0
QCNCMA230DRE0
QCNCMA234DRE0
QCNCMA267DRE0
QCNCMA237DRE0
QCNCWA030DRE0
RV-KXB003MRE0
PTPEHB010MRE0
RC-KZA087DRE0
VCEAB31VW108M
RC-KZA087DRE0
VCEAB31VW106M
RC-KZA087DRE0
VCEAB31VW106M
VCKYD11CY103N
RC-KZA087DRE0
VCEAB31VW106M
VCEAB31HW104M
VCKYD11CY103N
VCKYD11CY103N
VCKYD11CY103N
VCKYD11HB331K
RC-QZB014MRE0
M
J
J
J
J
J
J
M
M
J
J
J
J
J
J
J
J
J
J
J
J
J
J
M
Control unit
3-pin connector CN-A
4-pin connector CN-B
5-pin connector CN-C
6-pin connector CN-E
3-pin connector CN-F
12-pin connector CN-G
Fluorescent display tube
Tape 2mm
Capacitor
0.1 uF
50V
Capacitor
1000 uF
35V
Capacitor
0.1 uF
50V
Capacitor
10 uF
35V
Capacitor
0.1 uF
50V
Capacitor
10 uF
35V
Capacitor
0.01 uF
16V
Capacitor
0.1 uF
50V
Capacitor
10 uF
35V
Capacitor
0.1 uF
50V
Capacitor
0.01 uF
16V
Capacitor
0.01 uF
16V
Capacitor
0.01 uF
16V
Capacitor
330 pF
50V
Capacitor
7 uF
230V
49
R-1855A
REF. NO.
CF1
D1-4
D20-32
D70-76
IC1
IC2
Q1
Q3
Q4
Q20-26
Q27
Q28-30
Q40
Q60
Q90
R1
R2
R3
R4
R7-8
R30
R31
R40
R50
R51
R62
R63
R64
R70-74
R75
R76-82
R90-93
R100
RY1-3
RY4-9
RY10
SP40
T1
VRS1
ZD1
ZD2
ZD3
ZD4
3- 2
3- 2-1
3- 2-2
3- 2-3
3- 2-4
3- 2-5
3- 2-6
3- 3
PART NO.
RCRS-A010DRE0
VHD11ES1///-1
VHD1SS270A/-1
VHD1SS270A/-1
RH-IZA719DRE0
RH-IZA495DRE0
VS2SB1238//-3
VSKRA101M//-3
VSDTA123ES/-3
VSKRA101M//-3
VSKRC243M//-3
VSKRA101M//-3
VSKRA101M//-3
VSKRC101M//-3
VSKRA101M//-3
VRD-B12HF432J
VRD-B12EF152J
VRS-B13AA681J
VRD-B12HF511J
VRD-B12EF472J
VRD-B12EF153J
VRD-B12EF472J
VRD-B12EF332J
VRD-B12EF153J
VRD-B12EF472J
VRN-B12EK363F
VRN-B12EK221F
VRN-B12EK362F
VRD-B12EF332J
VRD-B12EF104J
VRD-B12EF332J
VRD-B12EF104J
VRS-B13AA331J
RRLY-B002MRE0
RRLY-A075DRE0
RRLY-B001MRE0
RALM-A014DRE0
RTRNPB004MRE0
RH-VZA032DRE0
VHEHZ6A3///-1
VHEHZ161///-1
VHEHZ5C2///-1
VHEHZ4A2///-1
FPNLCB153MRK0
FUNTKB108MRE0
GMADIB023MRF0
MSPRTA050WRE0
JBTN-B053MRF0
JBTN-B055MRF0
LANGQB036MRP0
XEPSD30P10XS0
§
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
M
J
M
J
M
J
J
J
J
J
M
M
M
M
M
M
M
M
DESCRIPTION
Ceramic resonator (CST4.00MGW)
Diode (11ES1)
Diode (1SS270A)
Diode (1SS270A)
LSI
IC
Transistor (2SB1238)
Transistor (KRA101M)
Transistor (DTA123ES)
Transistor (KRA101M)
Transistor (KRC243M)
Transistor (KRA101M)
Transistor (KRA101M)
Transistor (KRC101M)
Transistor (KRA101M)
Resistor
4.3k ohm
1/2W
Resistor
1.5k ohm
1/4W
Resistor
680 ohm
1W
Resistor
510 ohm
1/2W
Resistor
4.7k ohm
1/4W
Resistor
15k ohm
1/4W
Resistor
4.7k ohm
1/4W
Resistor
3.3k ohm
1/4W
Resistor
15k ohm
1/4W
Resistor
4.7k ohm
1/4W
Resistor
36k ohm
1/4W
Resistor
220 ohm
1/4W
Resistor
3.6k ohm
1/4W
Resistor
3.3k ohm
1/4W
Resistor
100k ohm
1/4W
Resistor
3.3k ohm
1/4W
Resistor
100k ohm
1/4W
Resistor
330 ohm
1W
Relay (DU24D1-1P(M))
Relay (OJE-SS-124LM)
Relay (VE-24HSF-K)
Buzzer (PKM22EPT)
Transformer
Varistor (10G471K)
Zener diode (HZ6A-3)
Zener diode (HZ16-1)
Zener diode (HZ5C-2)
Zener diode (HZ4A-2)
Control panel sub. assembly
Key unit
Display window
Open button spring
Open button
Select button
Key fixing
Screw; 3mm x 10mm
FFTA-B002MRK0
FROLPB020MRK0
NTNT-B006MRE0
LANGKB010MRP0
FCOVPB002MRY0
FFAN-B008MRK0
------------DHET-B001MRK0
NCPL-B006MRF0
NFANMB003MRP0
LANGQB031MRP0
PPACGB013MRE0
LBNDK0054WRE0
NFANMB004MRP0
PHOK-B013MRF0
FANGTB003MRY0
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
Exhaust damper assembly
Turntable support assembly
Turntable tray
Capacitor holder
Stirrer cover assembly
Stirrer fan assembly
Oven cavity (Not a replaceble part)
Convection heater unit
Coupling
Convection motor fan
Convection motor angle
Turntable motor packing
Heater mounting holder
Convection fan
Latch hook
Unit mounting plate
Q'TY CODE
1
AD
4
AB
13
AA
7
AA
1
AW
1
AL
1
AA
1
AB
1
AA
7
AB
1
AB
3
AB
1
AB
1
AB
1
AB
1
AH
1
AA
1
AA
1
AB
2
AA
1
AA
1
AA
1
AA
1
AA
1
AA
1
AA
1
AB
1
AA
5
AA
1
AA
7
AA
4
AA
1
AA
3
AH
6
AG
1
AM
1
AG
1
AN
1
AE
1
AC
1
AA
1
AA
1
AA
1
BB
1
AX
1
AD
1
AA
1
AD
1
AC
1
AL
5
AA
OVEN PARTS
∆
∆
4- 1
4- 2
4- 3
4- 4
4- 5
4- 6
4- 7
4- 8
4- 9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
50
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
AM
AS
AZ
BB
AM
AK
-BL
AE
AE
AF
AC
AD
AE
AG
AV
R-1855A
REF. NO.
4-17
4-18
4-19
4-20
4-21
4-22
4-23
4-24
4-25
4-26
4-27
4-28
4-29
4-30
4-31
4-32
4-33
4-34
4-35
4-36
4-37
4-38
4-39
4-40
4-41
4-42
4-43
4-44
4-45
4-46
4-47
4-48
4-49
4-50
4-51
4-52
4-53
4-54
4-55
PART NO.
PFPF-B002MRE0
PPIPFB002MRE0
PREFHB006MRP0
PDUC-B083MRP0
NFANPB005MRK0
GBDYRB002MRP0
FDUC-B044MRK0
LBSHC0037WRE0
FDUC-B022MRK0
MLEVPB016MRF0
PCUSGB030MRP0
MCAMPB001MRF0
PCUSGB032MRP0
PFPF-B001MRE0
PFTA-B003MRP0
PREFHB004MRP0
LANGQB033MRP0
PREFHB005MRP0
LSTPPB024MRF0
PCOVPB047MRP0
PCOVPB050MRP0
PCUSGB027MRP0
PDUC-B056MRF0
PDUC-B057MRP0
PDUC-B058MRF0
PDUC-B060MRP0
PFILWA035WRE0
PFPF-B003MRE0
PCUSUB018MRP0
PCUSUB019MRP0
PCUSUB020MRP0
PCUSUB024MRP0
PCUSUB033MRP0
PCUSGB035MRP0
PCUSUB047MRP0
PCUSUB046MRP0
PFPF-B005MRE0
PFPF-B004MRE0
LANGQB025MRP0
§
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
DESCRIPTION
Heat protect L
Coller
Heater cover L
Hood intake duct L
Fan blade
Back plate
Fan duct
Cord bushing
Exhaust duct
Open lever
Cushion
Damper cam
Damper cushion
Heat protect R
Damper plate
Thermal cover R
Hood lamp angle
Thermal cover bottom
Door stopper
Oven lamp cover
Heat protect top sheet
Cushion
Hood exhaust duct
Top duct
Magnetron duct
Hood intake duct R
Oven light screen
Heat protect top
Exhaust cushion A
Exhaust cushion B
Cushion
Cushion
Cushion
Cushion
Cushion
Cushion
Heat protect
Heat protect
Noise filter angle
Q'TY CODE
1
AK
1
AD
1
AM
1
AG
1
AC
1
AX
1
AM
1
AB
1
AK
1
AD
1
AC
1
AC
1
AC
1
AD
1
AD
1
AK
1
AM
1
AK
1
AD
1
AD
1
AK
1
AA
1
AY
1
AN
1
AD
1
AH
1
AF
1
AE
1
AA
1
AA
1
AA
1
AA
1
AD
1
AG
1
AD
1
AE
1
AR
1
AK
1
AE
DOOR PARTS
∆
∆
∆
∆
5
555555555-
1
2
3
4
5
6
7
8
9
CDORFB238MRK0
DDORFB074MRY0
GWAKPB058MRF0
PGLSPB008MRR0
GCOVHB031MRF0
LSTPPB025MRF0
LSTPPB028MRF0
MSPRTA046WRE0
PCUSUB022MRP0
XCTSD40P08000
M
M
M
M
M
M
M
M
M
M
Door assembly, complete
Door panel assembly
Door frame
Door glass front
Choke cover
Latch head
Glass stopper
Latch spring
Cushion
Screw : 4mm x 8mm
1
1
1
1
1
1
1
1
1
6
BL
BN
AS
AV
AM
AE
AD
AB
AC
AA
1
1
4
1
2
1
6
2
1
1
1
1
1
1
1
AN
AC
AC
AC
AC
AA
AA
AA
AD
AF
AD
AD
AD
AP
AY
MISCELLANEOUS
*
6- 1
6-1-1
6-1-2
6-1-3
6-1-4
6-1-5
6-1-6
6-1-7
6- 2
6- 3
6- 4
6- 5
6- 6
6- 7
6- 8
CFZK-B131MRK0
LBSHC0040MRE0
LX-BZ0195WRE0
LX-MZ0001WRE0
XBRSD50P60000
XOTSD40P12000
XTSSD50P35000
XWHSD50-16300
TINSEB141MRR0
TINSEB209MRR0
TINSKB018MRR0
TINSKB019MRR0
QW-QZB011MRE0
TCADCB012MRR0
FW-VZB171MRE0
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
Installation material assembly
Grommet
Toggle screw
Cord holder
Screw : 5mm x 60mm
Screw : 4mm x 12mm
Screw : 5mm x 35mm
Washer
Installation instruction
Operation manual
Top template
Wall template
High voltage wire A
Cook book
Main harness
A
51
R-1855A
REF. NO.
6- 9
6-10
6-11
6-12
6-13
6-13
6-14
6-15
PART NO.
FAMI-B005MRM0
FAMI-B006MRM0
FW-VZB077MRE0
TCAUAA041WRR0
TCAUAB005MRR0
TCAUAB034MRR0
TCAUAB037MRR0
TCAUAB008MRR0
§
M
M
M
M
M
M
M
M
DESCRIPTION
High rack
Low rack
Main harness
C
Caution label
DHHS caution label
NHW caution label
Monitor caution label
User caution label (CANADIAN)
XCPSD40P08000
XOTSF40P10000
XCBSD30P08000
XBTSD40P08RV0
XCBSD30P08000
XBTWW40P06000
XOTSD40P12000
XOTSF40P10000
XBTSD40P08000
LX-BZB011MRE0
LX-CZA038WRE0
XCBWW30P06000
LX-CZ0052WRE0
XCTWW40P08RV0
XRESD40-06000
XOTSD40P12000
XCTWW40P08000
XNEUW40-32000
XWSUW40-10000
LX-BZ0081YBE0
XWHSD50-20120
XWHUW40-08100
XWHUW50-08120
XOTSD40P08000
XOTWW40P10000
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
Screw : 4mm x 8mm
Screw : 4mm x 10mm
Screw : 3mm x 8mm
Screw : 3mm x 6mm
Screw : 3mm x 8mm
Screw : 4mm x 6mm
Screw : 4mm x 12mm
Screw : 4mm x 10mm
Screw : 4mm x 8mm
Unit mounting screw
Special screw
Screw : 3mm x 6mm
Special screw
Screw : 4mm x 8mm
E-ring
Screw : 4mm x 12mm
Screw : 4mm x 8mm
Nut: 4mm x 3.2mm
Spring Washer
Screw : 4mm x 8mm
Washer : 5mm x 2mm
Washer : 4mm x 0.8mm
Washer : 5mm x 0.8mm
Screw : 4mm x 8mm
Screw : 4mm x 10mm
Q'TY CODE
1
AQ
1
AN
1
AH
1
AA
1
AB
1
AA
1
AA
1
AA
SCREWS,NUTS AND WASHERS
7- 1
7- 2
7- 3
7- 4
7- 5
7- 6
7- 7
7- 8
7- 9
7-10
7-11
7-12
7-13
7-14
7-15
7-16
7-17
7-18
7-19
7-20
7-21
7-22
7-23
7-24
7-25
HOW TO ORDER REPLACEMENT PARTS
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION
Order Parts from the authrized SHARP parts Distributor for your area.
Defective parts required return should be returned as indicated in the Service Policy.
52
2
3
2
2
2
2
24
1
2
2
4
5
2
2
1
2
1
1
1
9
1
2
1
9
10
AA
AB
AA
AA
AA
AA
AA
AA
AA
AH
AA
AA
AA
AA
AA
AC
AA
AB
AA
AA
AA
AA
AA
AA
AA
R-1855A
2
1
4
3
6
5
OVEN AND CABINET
PARTS
A
A
4-52
4-52
4-50
1-17
7-25
4-1
4-50
7-24
4-51
4-16
B
B
7-7
7-24
2-10
4-39
4-46
7-11
4-36
4-25
7-7
C
7-24
7-24
4-37
1-21
7-3
4-45
C
4-24
7-11
4-40
7-17
2-5
1-13
4-38
7-5
2-6
7-7
1-7
4-44
4-8
7-11
7-7
4-22
7-20
D
D
7-5
4-20
7-21
7-14 7-15
7-23
1-16
2-9
7-14
4-10
4-11
1-6
1-3
4-7
7-1
1-4
7-20
7-4
4-4
4-19
E
7-7
7-7
1-20
4-18
1-18
4-54
6-13
1-15
4-13
4-17
7-6
7-24
4-14
7-12
6-12
1-5
7-22
2-2
4-23
4-53
4-34
7-18
4-13
1-24
7-13
4-9
7-22
F
1-9
7-1
7-25
7-12
7-19
1-2
1-1
4-43
7-12
7-20
4-33
1-20
4-26
1-20
4-15
1-19
4-48
1-11
4-29
1-11
4-31
1-7
4-28
1-14
7-25
G
1-23
4-3
4-49
1-22
4-47
7-7
7-7
2-8
7-7
F
4-50
1-14
2-4
7-5
4-55
7-9
1-12
7-16
1-8
7-5
4-21
1-11
4-41
1-10
4-27
4-6
4-5
E
7-16
4-12
G
4-30
6-14
2-1
2-3
7-7
4-32
7-20
4-42
7-10
2-7
7-7
2-1
4-2
7-10
2-7-2
H
H
2-7-1
7-8
1
2
7-2
4
3
53
5
6
R-1855A
2
1
4
3
6
5
CONTROL PANEL PARTS
A
A
3-2
3-3
3-1
3-2-2
3-2-6
B
DOOR PARTS
6-15
B
3-2-1
4-35
7-7
3-3
6-15
5-9
3-2-5
C
5-4
3-2-4
5-6
C
5-1
3-2-3
5-9
D
D
5-5
5
5-7
5-8
E
E
5-3
5-2
MISCELLANEOUS
6-1
6-8
F
6-1-1
F
6-6
6-1-4
6-1-5
6-1-2
G
6-1-3
6-1-6
6-1-7
G
6-10
6-9
6-11
H
H
1
2
4
3
54
5
6
R-1855A
PACKING AND ACCESSORIES
6-1
INSTALL MATERIAL ASSEMBLY
6-7
COOK BOOK
6-3 OPERATION MANUAL
6-5 WALL TEMPLATE
TOP PAD
DOOR PROTECTOR
WRAP COVER
6-2 INSTALLATION INSTRUCTION
6-4 TOP TEMPLATE
2-1 GREASE FILTER (x 2)
6-10 LOW RACK
6-9 HIGH RACK
BOTTOM PAD
MILLER MAT
4-3 TURNTABLE TRAY
TAPE
4-2 TURNTABLE
SUPPORT
ASSEMBLY
PACKING CASE
Non-replaceable items
TRAY HOLDER
4-1 DAMPER ASSEMBLY
DAMPER HOLDER
55
R-1855A
NOTES:
56
R-1855A
NOTES:
57
R-1855A
COPYRIGHT © 1999 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in retrieval systems, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
'99 SHARP CORP. (9M3.20E) Printed in U.S.A
58