Mitsubishi Electric PLA-ZRP35 Service manual

SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS
SPLIT-TYPE, AIR CONDITIONERS
November 2012
No. OCH535
SERVICE MANUAL
Indoor unit
[Model names]
PLA-ZRP35BA
PLA-ZRP50BA
PLA-ZRP60BA
PLA-ZRP71BA
PLA-ZRP125BA
PLA-ZRP140BA
[Service Ref.]
PLA-ZRP35BA.UK
PLA-ZRP50BA.UK
PLA-ZRP60BA.UK
PLA-ZRP71BA.UK
PLA-ZRP125BA.UK
PLA-ZRP140BA.UK
NOTE:
• This manual describes
only service data of the
indoor units.
• RoHS compliant products have <G> mark on
the spec name plate.
CONTENTS
Model name
indication
INDOOR UNIT
ON/OFF
1. REFERENCE MANUAL................................... 2
2. SAFETY PRECAUTION................................... 3
3. PART NAMES AND FUNCTIONS................... 4
4. SPECIFICATIONS...........................................12
5. NOISE CRITERION CURVES.........................14
6. OUTLINES AND DIMENSIONS......................16
7. WIRING DIAGRAM.........................................17
8. REFRIGERANT SYSTEM DIAGRAM............ 18
9. TROUBLESHOOTING....................................19
10. SPECIAL FUNCTION .....................................35
11. DISASSEMBLY PROCEDURE.......................45
TEMP
TEMP.
WIRELESS REMOTE
CONTROLLER
ON/OFF
WIRED REMOTE
CONTROLLER
PARTS CATALOG (OCB535)
1
REFERENCE MANUAL
OUTDOOR UNIT’S SERVICE MANUAL
Service Ref.
Service Manual No.
PUHZ-ZRP35/50VKA
PUHZ-ZRP60/71VHA
PUHZ-ZRP125/140VKA
PUHZ-ZRP125/140YKA
OCH527/OCB527
OCH535
2
2
SAFETY PRECAUTION
2-1. ALWAYS OBSERVE FOR SAFETY
Before obtaining access to terminal, all supply circuits must be disconnected.
2-2. CAUTIONS RELATED TO NEW REFRIGERANT
Cautions for units utilising refrigerant R410A
Use new refrigerant pipes.
In case of using the existing pipes for R22, be careful with
the followings.
· For ZRP125 and 140, be sure to perform replacement
operation before test run.
· Change flare nut to the one provided with this product.
Use a newly flared pipe.
· Avoid using thin pipes.
Make sure that the inside and outside of refrigerant piping is clean and it has no contaminants
such as sulfur, oxides, dirt, shaving particles, etc,
which are hazard to refrigerant cycle.
In addition, use pipes with specified thickness.
Contamination inside refrigerant piping can cause deterioration of refrigerant oil etc.
Use a vacuum pump with a reverse flow check
valve.
Vacuum pump oil may flow back into refrigerant cycle and
that can cause deterioration of refrigerant oil etc.
Use the following tools specifically designed for
use with R410A refrigerant.
The following tools are necessary to use R410A refrigerant.
Gauge manifold
Charge hose
Gas leak detector
Torque wrench
Tools for R410A
Flare tool
Size adjustment gauge
Vacuum pump adaptor
Electronic refrigerant
charging scale
Handle tools with care.
Store the piping indoors, and keep both ends of
the piping sealed until just before brazing.
(Leave elbow joints, etc. in their packaging.)
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of compressor.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of compressor.
Do not use a charging cylinder.
The refrigerant oil applied to flare and flange
connections must be ester oil, ether oil or
alkylbenzene oil in a small amount.
If large amount of mineral oil enters, that can cause deterioration of refrigerant oil etc.
Charge refrigerant from liquid phase of gas
cylinder.
If the refrigerant is charged from gas phase, composition
change may occur in refrigerant and the efficiency will be
lowered.
Do not use refrigerant other than R410A.
If a charging cylinder is used, the composition of refrigerant will change and the efficiency will be lowered.
Use the specified refrigerant only.
Never use any refrigerant other than that specified.
Doing so may cause a burst, an explosion, or fire when the
unit is being used, serviced, or disposed of.
Correct refrigerant is specified in the manuals and on the
spec labels provided with our products.
We will not be held responsible for mechanical failure,
system malfunction, unit breakdown or accidents caused
by failure to follow the instructions.
Ventilate the room if refrigerant leaks during
operation. If refrigerant comes into contact with
a flame, poisonous gases will be released.
If other refrigerant (R22 etc.) is used, chlorine in refrigerant can cause deterioration of refrigerant oil etc.
[1] Cautions for service
(1) Perform service after recovering the refrigerant left in unit completely.
(2) Do not release refrigerant in the air.
(3) After completing service, charge the cycle with specified amount of refrigerant.
(4) When performing service, install a filter drier simultaneously.
Be sure to use a filter drier for new refrigerant.
[2] Additional refrigerant charge
When charging directly from cylinder
· Check that cylinder for R410A available on the market is syphon type.
· Charging should be performed with the cylinder of syphon stood vertically. (Refrigerant is charged from liquid phase.)
OCH535
3
Unit
Gravimeter
[3] Service tools
Use the below service tools as exclusive tools for R410A refrigerant.
No.
1
Tool name
Specifications
Gauge manifold
· Only for R410A
· Use the existing fitting specifications. (UNF1/2)
· Use high-tension side pressure of 5.3MPa·G or over.
2
Charge hose
· Only for R410A
3
Electronic scale
4
Gas leak detector
· Use the detector for R134a, R407C or R410A.
5
Adaptor for reverse flow check
· Attach on vacuum pump.
6
Refrigerant charge base
7
Refrigerant cylinder
· Use pressure performance of 5.09MPa·G or over.
· Only for R410A
· Top of cylinder (Pink)
· Cylinder with syphon
8
3
Refrigerant recovery equipment
PART NAMES AND FUNCTIONS
3-1. INDOOR UNIT
Drain pipe
Filter
Air outlet
Liquid pipe
Gas pipe
i-see sensor
(option)
Vane
OCH535
Air intake
(Intake grille)
4
3-2. WIRELESS REMOTE CONTROLLER
CHECK TEST RUN display
CHECK and TEST RUN display indicate that
the unit is being checked or test-run.
MODEL SELECT display
Blinks when model is selected.
display
Lights up while the signal is transmitted to
the indoor unit when the button is pressed.
display
SET TEMP. display indicates the desired
temperature which is set.
CLOCK display
display
Displays the current time.
OPERATION MODE display
Operation mode display indicates which
operation mode is in effect.
TIMER display
CHECK TEST RUN
MODEL SELECT
°C
AMPM
AMPM
display
The vertical direction of air flow is indicated.
NOT AVAILABLE
ON/OFF
Used to change the fan speed.
MODE SELECT button
” display
”“
” display
button
MODE
FAN
AUTO STOP
VANE
AUTO START
each time the button is pressed.
FAN SPEED SELECT button
”“
Displays whether timer is on or off.
display
ON/OFF button
“
Displays the order of timer operation.
“
TEMP
FAN SPEED display indicates which fan
speed has been selected.
The unit is turned ON and OFF alternately
Displays when in timer operation or when
setting timer.
CHECK LOUVER
TEST RUN
SET
h
min
RESET
Used to switch the operation mode between
cooling, drying, heating, auto and fan mode.
SET TEMPERATURE button sets any desired
room temperature.
TIMER CONTROL buttons
AUTO STOP (OFF timer): when this switch
is set, the air conditioner will be
automatically stopped at the preset time.
AUTO START (ON timer): when this switch is
set, the air conditioner will be automatically
started at the preset time.
CLOCK
h and min buttons
Buttons used to set the “hour and minute” of
the current time and timer settings.
LOUVER button
CHECK-TEST RUN button
Changes left/right airflow direction.
(Not available for this model.)
Only press this button to perform an
inspection check or test operation.
Do not use it for normal operation.
CLOCK button
VANE CONTROL button
RESET button
Used to change the air flow direction.
OCH535
SET button
5
3-3. WIRED REMOTE CONTROLLER <PAR-30MAA / PAR-31MAA>
Wired remote controller function
* The functions which can be used are restricted according to the model.
Function
Body
: Supported
PAR-30MAA / PAR-31MAA
Slim
Product size H × W × D (mm)
LCD
: Unsupported
PAR-21MAA
City multi
120 × 120 × 19
120 × 130 × 19
Full Dot LCD
Partial Dot LCD
Backlight
Energy-saving
Energy-saving operation schedule
Automatic return to the preset temperature
Restriction
Setting the temperature range restriction
Function
Operation lock function
Weekly timer
On / Off timer
High Power
Manual vane angle
The functions of the function buttons change depending on
the screen. Refer to the button function guide that appears
at the bottom of the LCD for the functions they serve on a
given screen.
When the system is centrally controlled, the button function
guide that corresponds to the locked button will not appear.
<Main display>
<Main menu>
Fri
Room
Cool
Set temp.
Auto
Mode
Temp.
Fan
Function buttons
F1
F2
F3
Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
Cursor
Page
Function guide
F4
ON / OFF lamp
ON / OFF button
This lamp lights up in green while the unit is in operation.
It blinks while the remote controller is starting up or when
there is an error.
Press to turn ON/OFF the indoor unit.
SELECT button
Press to save the setting.
Function button F1
RETURN button
Main display : Press to change the operation mode.
Main menu : Press to move the cursor down.
Press to return to the previous screen.
Function button F2
MENU button
Main display : Press to decrease temperature.
Main menu : Press to move the cursor up.
Press to bring up the Main menu.
Backlit LCD
Function button F3
Operation settings will appear.
When the backlight is off, pressing any button turns the
backlight on and it will stay lit for a certain period of time
depending on the screen.
Main display : Press to increase temperature.
Main menu : Press to go to the previous page.
Function button F4
Main display : Press to change the fan speed.
Main menu : Press to go to the next page.
When the backlight is off, pressing any button turns
the backlight on and does not perform its function.
(except for the
(ON / OFF) button)
OCH535
Main
6
The main display can be displayed in two different modes: "Full" and "Basic".
The factory setting is "Full". To switch to the "Basic" mode, change the setting on the Main display setting.
<Full mode>
<Basic mode>
* All icons are displayed for explanation.
Fri
Fri
Cool
Room
Cool
Set temp.
Mode
Temp.
Set temp.
Auto
Auto
Mode
Fan
Temp.
Fan
Operation mode
Indoor unit operation mode appears here.
Appears when the buttons are locked.
Preset temperature
Preset temperature appears here.
Appears when the On/Off timer or Night setback function is
enabled.
Clock (See the Installation Manual.)
Current time appears here.
Fan speed
Appears when the Weekly timer is enabled.
Fan speed setting appears here.
Button function guide
Appears while the units are operated in the energy-save
mode.
Functions of the corresponding buttons appear here.
Appears when the ON/OFF operation is centrally controlled.
Appears when the operation mode is centrally controlled.
Appears when the built-in thermistor on the remote controller is activated to monitor the room temperature (a).
appears when the thermistor on the indoor unit is activated to monitor the room temperature.
Appears when the preset temperature is centrally controlled.
Indicates the vane setting.
Appears when the f lter reset function is centrally controlled.
Indicates the louver setting.
Indicates when f lter needs maintenance.
Room temperature
(See the Installation Manual.)
Indicates the ventilation setting.
Current room temperature appears here.
Appears when the preset temperature range is restricted.
Most settings (except ON / OFF, mode, fan speed, temperature) can be made from the Menu screen.
OCH535
7
Menu structure
Main menu
Press the MENU button.
Move the cursor to the desired item with the
F1
and
F2
buttons, and press the SELECT button.
Vane · Louver · Vent. (Lossnay)
High power
Timer
On / Off timer
Auto-Off timer
Filter information
Error information
Weekly timer
Energy saving
Auto return
Schedule
Night setback
Restriction
Temp. range
Operation lock
Maintenance
Auto descending panel
Manual vane angle
Initial setting
Main / Sub
Clock
Main display
Contrast
Display details
Auto mode
Administrator password
Language selection
Service
Service menu
Test run
Drain pump test run
Input maintenance info.
Function setting
Lossnay (City Multi only)
Check
Self check
Maintenance password
Remote controller check
Not all functions are available on all models of indoor units.
OCH535
8
Main menu list
Setting and display items
Setting details
Vane · Louver · Vent.
(Lossnay)
Use to set the vane angle.
• Select a desired vane setting from f ve different settings.
Use to turn ON / OFF the louver.
• Select a desired setting from "ON" and "OFF."
Use to set the amount of ventilation.
• Select a desired setting from "Off," "Low," and "High."
High power
Use to reach the comfortable room temperature quickly.
• Units can be operated in the High-power mode for up to 30 minutes.
Timer
On/Off timer
Use to set the operation On/Off times.
• Time can be set in 5-minute increments.
* Clock setting is required.
Auto-Off
timer
Use to set the Auto-Off time.
• Time can be set to a value from 30 to 240 in 10-minute increments.
Filter information
Use to check the f lter status.
• The f lter sign can be reset.
Error information
Use to check error information when an error occurs.
• Error code, error source, refrigerant address, unit model, manufacturing number, contact
information (dealer's phone number) can be displayed.
* The unit model, manufacturing number, and contact information need to be registered in
advance to be displayed.
Weekly timer
Use to set the weekly operation On / Off times.
• Up to eight operation patterns can be set for each day.
* Clock setting is required.
* Not valid when the On/Off timer is enabled.
Energy
saving
Auto return
Use to get the units to operate at the preset temperature after performing energy-save
operation for a specif ed time period.
• Time can be set to a value from 30 and 120 in 10-minute increments.
* This function will not be valid when the preset temperature ranges are restricted.
Schedule
Set the start/stop times to operate the units in the energy-save mode for each day of the
week, and set the energy-saving rate.
• Up to four energy-save operation patterns can be set for each day.
• Time can be set in 5-minute increments.
• Energy-saving rate can be set to a value from 0% or 50 to 90% in 10% increments.
* Clock setting is required.
Night setback
Restriction
Use to make Night setback settings.
• Select "Yes" to enable the setting, and "No" to disable the setting. The temperature range and
the start/stop times can be set.
* Clock setting is required.
Temp. range
Use to restrict the preset temperature range.
• Different temperature ranges can be set for different operation modes.
Operation
lock
Use to lock selected functions.
• The locked functions cannot be operated.
Maintenance Auto
descending
panel
Manual
vane angle
Initial setting Main/Sub
Clock
Auto descending panel (Optional parts) Up / Down you can do.
Use to set the vane angle for each vane to a f xed position.
When connecting two remote controllers, one of them needs to be designated as a sub
controller.
Use to set the current time.
Main display Use to switch between "Full" and "Basic" modes for the Main display.
• The default setting is "Full."
Contrast
OCH535
Use to adjust screen contrast.
9
Setting and display items
Initial setting Display
details
Auto mode
Setting details
Make the settings for the remote controller related items as necessary.
Clock: The factory settings are "Yes" and "24h" format.
Temperature: Set either Celsius (°C) or Fahrenheit (°F).
Room temp. : Set Show or Hide.
Auto mode: Set the Auto mode display or Only Auto display.
Whether or not to use the AUTO mode can be selected by using the button.
This setting is valid only when indoor units with the AUTO mode function are connected.
Administrator The administrator password is required to make the settings for the following items.
password
• Timer setting • Energy-save setting • Weekly timer setting
• Restriction setting • Outdoor unit silent mode setting • Night set back
Service
Language
selection
Test run
Use to select the desired language.
Select "Test run" from the Service menu to bring up the Test run menu.
• Test run • Drain pump test run
Input
Select "Input maintenance Info." from the Service menu to bring up the Maintenance
maintenance information screen.
The following settings can be made from the Maintenance Information screen.
• Model name input • Serial No. input • Dealer information input
Function
Make the settings for the indoor unit functions via the remote controller as necessary.
setting
This setting is required only when the operation of City Multi units is interlocked with
LOSSNAY
LOSSNAY units.
setting
(City Multi only)
Check
Error history: Display the error history and execute delete error history.
Refrigerant leak check: Refrigerant leaks can be judged.
Smooth maintenance: The indoor and outdoor maintenance data can be displayed.
Request cord: Details of the operation data including each thermistor temperature and error
history can be checked.
Self check
Error history of each unit can be checked via the remote controller.
Maintenance Take the following steps to change the maintenance password.
password
Remote
When the remote controller does not work properly, use the remote controller checking
controller
function to troublushoot the problem.
check
OCH535
10
3-4. WIRED REMOTE CONTROLLER <PAR-21MAA>
“Sensor” indication
Display Section
For purposes of this explanation,
all parts of the display are shown.
During actual operation, only
the relevant items will be lit.
Identifies the current operation
Displayed when the remote controller
sensor is used.
Day-of-Week
Shows the current day of the week.
Time/Timer Display
“Locked” indicator
Shows the current time, unless the simple or Auto Off
timer is set.
If the simple or Auto Off timer is set, the time to be
switched off is shown.
Indicates that remote controller buttons have been locked.
“Clean The Filter” indicator
Shows the operating mode, etc.
*Multilanguage display is available.
To be displayed on when it is time to
clean the filter.
TIME SUN MON TUE WED THU FRI SAT
TIMER
Hr
ON
AFTER
Indicates that operation from the
remote controller has been prohibited by a master controller.
Indicates that the timer is off.
Shows the target temperature.
FUNCTION
FILTER
WEEKLY
SIMPLE
AUTO OFF
ONLY1Hr.
The indicator comes on if the corresponding timer is set.
Fan Speed indicator
Shows the selected fan speed.
Up/Down Air Direction indicator
The indicator
shows the direction of the outcoming airflow.
“One Hour Only” indicator
Temperature Setting
Timer indicators
AFTER OFF
°F°C
°F°C
“Centrally Controlled” indicator
“Timer is Off” indicator
ERROR CODE
Displayed if the airflow is set to
low or downward during COOL
or DRY mode. (Operation varies
according to model.)
The indicator goes off in 1 hour,
when the airflow direction
also changes.
Room Temperature display
Shows the room temperature. The room
temperature display range is 8 – 39.
The display blinks if the temperature
is less than 8 or 39 or more.
Ventilation indicator
Appears when the unit is running in
Ventilation mode.
Louver display
Indicates the action of the swing louver.
Does not appear if the louver is not
running.
(Power On indicator)
Indicates that the power is on.
Operation Section
ON/OFF button
Temperature setting buttons
Down
Fan Speed button
Up
Timer Menu button
(Monitor/Set button)
Filter
button
(<Enter> button)
Mode button (Return button)
TEMP.
ON/OFF
Set Time buttons
Check button (Clear button)
Back
Ahead
Timer On/Off button
(Set Day button)
Test Run button
MENU
BACK
PAR-21MAA
MONITOR/SET
ON/OFF
FILTER
DAY
CLOCK
CHECK TEST
OPERATION
CLEAR
Airflow Up/Down button
Louver button
(
Operation button)
To return operation
number
Opening the
cover
Built-in temperature sensor
Ventilation button
( Operation button)
To go to next operation
number
Note:
L “PLEASE WAIT” message
This message is displayed for approximately 3 minutes when power is supplied to the indoor unit or when the unit is recovering from a power failure.
L “NOT AVAILABLE” message
This message is displayed if an invalid button is pressed (to operate a function that the indoor unit does not have).
If a single remote controller is used to operate multiple indoor units simultaneously that are different types, this message will not be displayed as
far as any of the indoor units is equipped with the function.
OCH535
11
INDOOR UNIT
Service Ref.
Mode
Power supply (phase, cycle, voltage)
Input
kW
Running current
A
External finish (Panel)
Heat exchanger
Fan
Fan (drive) % No.
Fan motor output
kW
Airflow (Low-Medium2-Medium1-High) */min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level (Low-Medium2-Medium1-High)
dB
Field drain pipe O.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
SPECIFICATIONS
Service Ref.
Mode
Power supply (phase, cycle, voltage)
Input
kW
Running current
A
External finish (Panel)
Heat exchanger
Fan
Fan (drive) % No.
Fan motor output
kW
Airflow (Low-Medium2-Medium1-High) */min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level (Low-Medium2-Medium1-High)
dB
Field drain pipe O.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
4
Service Ref.
Mode
Power supply (phase, cycle, voltage)
kW
Input
A
Running current
External finish (Panel)
Heat exchanger
kW
Fan
Fan (drive) % No.
*/min(CFM)
Fan motor output
Pa(mmAq)
Airflow (Low-Medium2-Medium1-High)
kW
External static pressure
Booster heater
Operation control & Thermostat
dB
Noise level (Low-Medium2-Medium1-High)
mm(in.)
Field drain pipe O.D.
W
mm(in.)
Dimensions
D
mm(in.)
H
mm(in.)
kg(lbs)
Weight
OCH535
Cooling
0.04
0.28
PLA-ZRP35BA.UK
Single phase, 50Hz, 230V
Heating
0.03
0.25
Munsell 6.4Y 8.9/0.4
Plate fin coil
Turbo fan (direct) % 1
0.050
11-13-15-16(390-460-530-565)
0(direct blow)
–
Remote controller & built-in
27-28-29-31
32 (1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 35 (1-3/8)
UNIT : 23 (51)
PANEL: 6 (13)
Cooling
0.04
0.30
PLA-ZRP50BA.UK
Single phase, 50Hz, 230V
Heating
0.03
0.27
Munsell 6.4Y 8.9/0.4
Plate fin coil
Turbo fan (direct) % 1
0.050
12-14-16-18(425-495-565-635)
0(direct blow)
–
Remote controller & built-in
28-29-31-32
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 35 (1-3/8)
UNIT : 23 (51)
PANEL: 6 (13)
Cooling
0.04
0.30
PLA-ZRP60BA.UK
Single phase, 50Hz, 230V
Heating
0.03
0.27
Munsell 6.4Y 8.9/0.4
Plate fin coil
Turbo fan (direct) % 1
0.050
12-14-16-18(425-495-565-635)
0(direct blow)
–
Remote controller & built-in
28-29-31-32
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 258 (10-3/16)
PANEL : 35 (1-3/8))
UNIT : 23 (51)
PANEL: 6 (13)
12
INDOOR UNIT
Service Ref.
Mode
Power supply (phase, cycle, voltage)
Input
kW
Running current
A
External finish (Panel)
Heat exchanger
Fan
Fan (drive) % No.
Fan motor output
kW
Airflow (Low-Medium2-Medium1-High) */min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level (Low-Medium2-Medium1-High)
dB
Field drain pipe O.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
Service Ref.
Mode
Power supply (phase, cycle, voltage)
Input
kW
Running current
A
External finish (Panel)
Heat exchanger
Fan
Fan (drive) % No.
Fan motor output
kW
Airflow (Low-Medium2-Medium1-High) */min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level (Low-Medium2-Medium1-High)
dB
Field drain pipe O.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
INDOOR UNIT
Service Ref.
Mode
Power supply (phase, cycle, voltage)
Input
kW
Running current
A
External finish (Panel)
Heat exchanger
Fan
Fan(drive) % No.
Fan motor output
kW
Airflow (Low-Medium2-Medium1-High) */min(CFM)
External static pressure
Pa(mmAq)
Booster heater
kW
Operation control & Thermostat
Noise level (Low-Medium2-Medium1-High)
dB
Field drain pipe O.D.
mm(in.)
Dimensions
mm(in.)
W
mm(in.)
D
mm(in.)
H
Weight
kg(lbs)
OCH535
Cooling
0.05
0.45
PLA-ZRP71BA.UK
Single phase, 50Hz, 230V
Heating
0.04
0.41
Munsell 6.4Y 8.9/0.4
Plate fin coil
Turbo fan (direct) % 1
0.120
17-19-21-23(600-671-740-810)
0(direct blow)
–
Remote controller & built-in
28-30-34-36
32(1-1/4)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16)
PANEL : 950 (37-3/8)
UNIT : 298 (11-3/4)
PANEL : 35 (1-3/8)
UNIT : 25 (55)
PANEL: 6 (13)
Cooling
0.09
0.80
PLA-ZRP125BA.UK
Single phase, 50Hz, 230V
Heating
0.08
0.71
Munsell 6.4Y 8.9/0.4
Plate fin coil
Turbo fan (direct) % 1
0.120
22-25-28-31(780-880-990-1,090)
0(direct blow)
–
Remote controller & built-in
34-36-39-41
32(1-1/4)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 298 (11-3/4) PANEL : 35 (1-3/8)
UNIT : 27 (60)
PANEL : 6 (13)
Cooling
0.12
1.07
PLA-ZRP140BA.UK
Single phase, 50Hz, 230V
Heating
0.11
0.95
Munsell 6.4Y 8.9/0.4
Plate fin coil
Turbo fan (direct) % 1
0.120
24-26-29-32(850-920-1,020-1,130)
0(direct blow)
–
Remote controller & built-in
36-39-42-44
32(1-1/4)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 840 (33-1/16) PANEL : 950 (37-3/8)
UNIT : 298 (11-3/4) PANEL : 35 (1-3/8)
UNIT : 27 (60)
PANEL : 6 (13)
13
5
NOISE CRITERION CURVES
PLA-ZRP35BA.UK
NOTCH SPL(dB)
High
31
Medium1
29
Medium2
28
Low
27
LINE
PLA-ZRP50BA.UK
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
80
70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
250
500
1000
2000
4000
10
8000
NC-70
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
BAND CENTER FREQUENCIES, Hz
PLA-ZRP60BA.UK
NOTCH SPL(dB)
High
32
Medium1
31
Medium2
29
Low
28
LINE
500
PLA-ZRP71BA.UK
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
OCTAVE .UKND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
250
1000
2000
4000
8000
NOTCH SPL(dB)
High
36
Medium1
34
Medium2
30
Low
28
LINE
90
80
10
NC-20
BAND CENTER FREQUENCIES, Hz
90
20
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
90
NOTCH SPL(dB)
High
32
Medium1
31
Medium2
29
Low
28
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
8000
BAND CENTER FREQUENCIES, Hz
OCH535
80
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
14
4000
8000
PLA-ZRP125BA.UK
NOTCH SPL(dB)
High
41
Medium1
39
Medium2
36
Low
34
PLA-ZRP140BA.UK
LINE
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
90
NOTCH SPL(dB)
High
44
Medium1
42
Medium2
39
Low
36
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
80
70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
8000
NC-70
BAND CENTER FREQUENCIES, Hz
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
UNIT
CEILING
1.5m
MICROPHONE
OCH535
500
1000
2000
BAND CENTER FREQUENCIES, Hz
15
4000
8000
6
OUTLINES AND DIMENSIONS
PLA-ZRP50BA.UK
PLA-ZRP125BA.UK
Ceiling hole
20~45
Unit: mm
20~45
860~910
810
Suspension bolt pitch
Detail connecting of branch duct(Both aspects)
100
100
Cut out hole
90
100
90
860~910
620
605
840
Indoor power supply
terminal block(Option part)
Ceiling hole
+
Suspension bolt pitch
Branch duct hole
155
Remote controller
terminal block
Indoor unit/Outdoor unit
connecting terminal block
Branch duct hole
350
:175
167
70°
160
(7.5)
160
20~45
Fresh air
intake hole
PLA-ZRP60BA.UK
PLA-ZRP140BA.UK
130
PLA-ZRP35BA.UK
PLA-ZRP71BA.UK
+
14-:2.8
Burring hole
Burring hole pitch
:150
Detail drawing of fresh air intake hole
(7.5)
24
160
D
Burring hole
1
60
284
(
Connected the attached
Drain pipe
connected to VP-25 flexible pipe or socket.
377
Control wire entry
597
B
Auto vane
(Air outlet)
switch<Cooling>and
Emergency Up/Down switch<Up>
Emergency operation
switch<Heating>and
Emergency Up/Down switch<Down>
Receiver
M
83
M
83
500
36
Vane motor
36
950
Indoor unit
Indoor unit
1000mm
or more
DEFROST/STAND BY lamp
Operation lamp
Air outlet hole
3000mm or more
Obstacle
2500mm or more
from floor
For high
attachment
Air intake grille
Note1. Please choose the grille from a standard grille, auto-grille.
2. As for drain pipe, please use VP-25(O.D. :32 PVC TUBE).
Drain pump is included.
Max. lifting height is 850mm from the ceiling.
3. As for suspension bolt, please use M10 or W3/8.
(Procured at local site)
4. Electrical box may be removed for the service purpose.
Make sure to slack the electrical wire little bit for control/power wires connection.
5. The height of the indoor unit is able to be adjusted with the grille attached.
6. For the installation of the optional high efficiency filter or optional multi-functional casement.
1) Requires E or more space between transom and ceiling for the installation.
2) Add 135 mm to the dimensions + marked on the figure.
3) The optional high efficiency filter must be used jointly with the optional multi-functional casement.
7. When installing the branch ducts, be sure to insulate adequately.
Otherwise condensation and dripping may occur.
(It becomes the cause of dew drops/Water dew.)
8. As for necessary installation/service space, please refer to the left figure.
Models
PLA-ZRP35/50BA
Floor
PLA-ZRP60BA
1
Refrigerant pipe
···:6.35
Flared connection
···1/4 inch
Refrigerant pipe
:6.35 / :9.52
Flared connection
1/4 inch/ 3/8 inch
(compatible)
PLA-ZRP71/125/140BA Refrigerant pipe
···:9.52
Flared connection
···3/8 inch
OCH535
Ceiling
L.L Filter
Air intake grille
1500mm
or more
Ceiling
In case of auto-grille : PLP-6BAJ
In case of wireless remote controller : PLP-6BALM Auto grille
Air intake grille up/down distance
Emergency operation
Air intake hole
Air outlet hole
M
Grille
+
In case of standard grille : PLP-6BA / PLP-6BAMD
Drain hole
Drain pump clean hole
and Drain emergency
drainage hole
M
Ceiling
Cut out hole
:100
Grille
597
500
190
Ceiling
)
35
Power supply wire,
Indoor unit/Outdoor unit
connecting wire entry
+
Keep approximately
10 to 15mm space
between unit ceiling
and ceiling slab.
+
17 +50
50~70
+
Air intake hole
950
+
+
+
Suspension bolt
lower edge
156
105
140
170
A
2
+
Burring hole pitch
:125
120°
120°
840
158
Suspension bolt
M10 or W3/8
3-:2.8
20~45
160
187.5
16
2
Refrigerant pipe
···:12.7
Flared connection
···1/2 inch
Refrigerant pipe
···:15.88
Flared connection
···5/8 inch
A
B
C
D
E
74
400
77
440
80
241
258
87
281
298
85
Max. 4.0m
C
90
150
Cut out hole
7
WIRING DIAGRAM
PLA-ZRP35BA.UK
PLA-ZRP71BA.UK
PLA-ZRP50BA.UK
PLA-ZRP125BA.UK
PLA-ZRP60BA.UK
PLA-ZRP140BA.UK
[LEGEND]
SYMBOL
I.B
CN2L
CN32
CN41
CN51
FUSE
LED1
LED2
LED3
SW1
SW2
SWE
X1
DCL
DP
FS
NAME
INDOOR CONTROLLER BOARD
CONNECTOR (LOSSNAY)
CONNECTOR (REMOTE SWITCH)
CONNECTOR (HA TERMINAL-A)
CONNECTOR (CENTRALLY CONTROL)
FUSE (T6.3AL250V)
POWER SUPPLY (I.B)
POWER SUPPLY (R.B)
TRANSMISSION (INDOOR-OUTDOOR)
SWITCH (MODEL SELECTION) + See table 1
SWITCH (CAPACITY CODE) + See table 2
CONNECTOR (EMERGENCY OPERATION)
RELAY (DRAIN PUMP)
REACTOR
DRAIN PUMP
DRAIN FLOAT SWITCH
SYMBOL
MF
MV
TB2
TB4
TB5,TB6
TH1
TH2
TH5
OPTION PART
W.B
BZ
LED1
LED2
RU
SW1
SW2
NAME
FAN MOTOR
VANE MOTOR
TERMINAL BLOCK (Indoor unit Power (option))
TERMINAL BLOCK (INDOOR/OUTDOOR CONNECTING LINE)
TERMINAL BLOCK (REMOTE CONTROLLER
TRANSMISSION LINE)
ROOM TEMP. THERMISTOR
(0°C / 15kΩ, 25°C / 5. 4kΩ DETECT)
PIPE TEMP. THERMISTOR/LIQUID
(0°C / 15kΩ, 25°C / 5. 4kΩ DETECT)
COND. / EVA. TEMP. THERMISTOR
(0°C / 15kΩ, 25°C / 5. 4kΩ DETECT)
PCB FOR WIRELESS REMOTE CONTROLLER
BUZZER
LED (OPERATION INDICATION : GREEN)
LED (PREPARATION FOR HEATING : ORANGE)
RECEIVING UNIT
EMERGENCY OPERATION (HEAT / DOWN)
EMERGENCY OPERATION (COOL / UP)
<Table 2> SW2 (CAPACITY CODE)
SW2
MODELS Manufacture/Service MODELS Manufacture/Service
PLA-ZRP35BA
PLA-ZRP50BA
PLA-ZRP60BA
1 2 3 4 5
ON PLA-ZRP71BA
OFF
1 2 3 4 5
ON PLA-ZRP125BA
OFF
1 2 3 4 5
ON PLA-ZRP140BA
OFF
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
<Table 1> SW1 (MODEL SELECTION)
SW1
Manufacture/Service
ON
OFF
1 2 3 4 5
Refer to tables 1 and 2
ON
OFF
ON
OFF
TB5
2
1
TRANSMISSION
WIRES
DC12V
2 1
TB6
The black square ( ) indicates a switch position.
ON
OFF
DCL
The black square ( )
indicates a switch position.
YLW
R.B
I.B
VANE CNV(WHT)
SW1
20 18 16 14 12 10 8 6 4 2
SW2
J41 J42
CN32
(WHT) 1
CN51(WHT)
Pair No.
19 17 15 13 11 9 7 5 3 1
5
3
1
3
WIRELESS
CN90
(WHT)
9
5
CNB
5
BZ
M
M
M
M
SW1
LED2
MV
MV
MV
MV
SW2
LED1
GRILLE
I-SEE
SENSOR
CN4Y
1 (WHT) 4
4
9
5
LED1
1
2 1
4
ON
AUTO GRILLE
CN3G 1
(BLK)
5
LED2
I-SEE
SENSOR
I-SEE
SENSOR MOTOR
CN6Y
(RED) 6
1
5
CN105
1
5
I-SEE SENSOR
CORNER PANEL
(OPTION PART)
RU
W.B
1 3 5
FUSE
DC325V
REMOCON
CN22
1
(BLK)
(BLU)
1 2
RECTIFICATION
(BLU)
OFF
FLOAT SW LIQUID/PIPE INTAKE
CN20
CN4F
CN44
(RED)
(WHT)
(WHT)
1
4 1
3
4
t°
M
MT
SWE
OUTDOOR
CN01
1 3
INDOOR/OUTDOOR
COMMUNICATION
CN3C
CN41(WHT)
CN2L
LED3
3
FS
t°
TH2 TH5
1 2
7
X1
FAN D.U.M
CNMF CNP
(WHT) (BLU)
t°
TH1
1 3
4
11
MS
3~
M
1~
MF
DP
AUTO
GRILLE
POWER
CNAC
(WHT)
3
YLW
ORN
TB4
YLW
S1
ORN
S2
S3
TO
OUTDOOR
UNIT
ORN
BRN
U.B
3
CN3G
1
5 3 1
CN3A
AUTOMATIC FILTER ELEVATION PANEL
(OPTION PART)
+Be sure to turn off the source power and then
disconnect fan motor connector.
(Failure to do so will cause trouble in fan motor)
+ 1(Fig. 1)
Notes: 1. SymboIs used in wiring diagram above are,
:Connector,
:
Terminal (block).
2. Indoor and outdoor connecting wires are made with poIarities, make
wiring matching terminal numbers (S1, S2, S3).
3. Since the outdoor side electric wiring may change be sure to check
the outdoor unit electric wiring for servicing.
4. This diagram shows the wiring of indoor and outdoor connecting
wires (specification of 230V), adopting superimposed system of
power and signal.
+ 1: When work to Supply power separately to indoor and outdoor
units was applied, refer to Fig 1.
+ 2: For power supply system of this unit, refer to the caution label
located near this diagram.
Please set the voltage using the
remote controller.
For the setting method,please refer to
the indoor unit Installation Manual.
OCH535
17
CN01
(BLK)
5
3
1
CN3C
(BLU)
3
1
I.B
YLW
ORN
RED
BLU
GRN/YLW
YLW
ORN
ORN
BRN
TB2
L
N
POWER SUPPLY
~(1PHASE)
230V 50Hz
TB4
S1
S2
S3
TO OUTDOOR UNIT
INDOOR/OUTDOOR
COMMUNICATION
[Self-diagnosis]
1.For details on how to operate self-diagnosis with the wireless
remote control,refer to the technical manuals etc.
2.For the wired remote control:When you quickly press twice the
CHECK switch on the remote control, the unit begins self-diagnosis,
and Check Codes generated in the past appear on the display.
For Check Codes and Symptoms refer to the table below.
8
REFRIGERANT SYSTEM DIAGRAM
PLA-ZRP35BA.UK
PLA-ZRP71BA.UK
PLA-ZRP50BA.UK
PLA-ZRP125BA.UK
PLA-ZRP60BA.UK
PLA-ZRP140BA.UK
Strainer (#50)
Heat exchanger
Refrigerant GAS pipe connection
(Flare)
Thermistor TH5
(Cond./ Eva.temperature)
Refrigerant flow in cooling
Refrigerant flow in heating
Refrigerant LIQUID pipe connection
(Flare)
Thermistor TH1
(Room temperature)
Thermistor TH2
Pipe temperature(Liquid)
Distributor
with strainer (#50)
OCH535
Strainer (#50)
18
9
TROUBLESHOOTING
9-1. TROUBLESHOOTING
<Error code display by self-diagnosis and actions to be taken for service (summary)>
Present and past error codes are logged and displayed on the wired remote controller or controller board of outdoor unit.
Actions to be taken for service and the trouble reoccurrence at field are summarized in the table below. Check the contents
below before investigating details.
Unit conditions at service
Error code
Actions to be taken for service (summary)
Displayed
Judge what is wrong and take a corrective action according
to “9-3. Self-diagnosis action table”.
The trouble is reoccurring.
Not displayed
Consider the temporary defects such as the work of
protection devices in the refrigerant circuit including
compressor, poor connection of wiring, noise and etc.
Re-check the symptom, and check the installation
environment, refrigerant amount, weather when the
trouble occurred, matters related to wiring and etc.
Reset error code logs and restart the unit after finishing
service.
There is no abnormality in electrical component,
controller board, remote controller and etc.
Logged
The trouble is not reoccurring.
Re-check the abnormal symptom.
Conduct trouble shooting and ascertain the cause of
the trouble according to “9-4. Troubleshooting of
problems”.
Continue to operate unit for the time being if the cause
is not ascertained.
There is no abnormality concerning of parts such as
electrical component, controller board, remote controller
and etc.
Not logged
OCH535
Conduct troubleshooting and ascertain the cause of the
trouble according to “9-4. Troubleshooting of problems”.
19
9-2. MALFUNCTION-DIAGNOSIS METHOD BY REMOTE CONTROLLER
<In case of trouble during operation>
When a malfunction occurs to air conditioner, both indoor unit and outdoor unit will stop and operation lamp blinks to inform
unusual stop.
<Malfunction-diagnosis method at maintenance service>
[Procedure]
Refrigerant
address
display
CHECK
CHECK
display
Temperature
button
TEMP
ON/OFF
1. Press the CHECK button twice.
• "CHECK" lights, and refrigerant
address "00" flashes.
• Check that the remote controller's
display has stopped before continuing.
2. Press the temperature
buttons.
• Select the refrigerant address of the
indoor unit for the self-diagnosis.
Note: Set refrigerant address using the
outdoor unit’s DIP switch (SW1).
(For more information, see the
outdoor unit installation manual.)
3. Point the remote controller at the
sensor on the indoor unit and
press the HOUR button.
• If an air conditioner error occurs,
the indoor unit's sensor emits an
intermittent buzzer sound, the
operation light flashes, and the error
code is output.
(It takes 3 seconds at most for error
code to appear.)
4. Point the remote controller at the
sensor on the indoor unit and
press the ON/OFF button.
• The check mode is cancelled.
ON/OFF
button
MODE
FAN
AUTO STOP
VANE
AUTO START
CHECK LOUVER
CHECK
button
min
TEST RUN
SET
h
HOUR
button
RESET
OCH535
CLOCK
20
• Refer to the following tables for details on the check codes.
[Output pattern A]
Beeper sounds
OPERATION
INDICATOR
lamp flash
pattern
Beep
Beep Beep Beep
Off
Beep
1st
2 nd
3 rd
nth
On
On
On
On
Beep Beep
1st
Off
On
2 nd · · · Repeated
On
0.5 sec. Approx. 2.5 sec. 0.5 sec. 0.5 sec.
Self-check Approx. 2.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.
starts
(Start signal
Number of flashes/beeps in pattern indicates the check Number of flashes/beeps in pattern indicates
received)
code in the following table (i.e., n=5 for “P5”)
the check code in the following table
[Output pattern B]
Beeper sounds
OPERATION
INDICATOR
lamp flash
pattern
Beep
Beep Beep Beep
1st
Off
Self-check Approx. 2.5 sec.
starts
(Start signal
received)
On
Approx. 3 sec.
2nd
3 rd
On
On
On
0.5 sec. 0.5 sec. 0.5 sec.
Beep
Beep
nth
1st
On
Off
0.5 sec. Approx. 2.5 sec.
Number of flashes/beeps in pattern indicates the check
code in the following table (i.e., n=5 for “U2”)
On
Approx. 3 sec.
Beep
2 nd · · · Repeated
On
On
0.5 sec. 0.5 sec.
Number of flashes/beeps in pattern indicates
the check code in the following table
[Output pattern A] Errors detected by indoor unit
Wireless remote controller Wired remote controller
Beeper sounds/OPERATION
Symptom
Check code
INDICATOR lamp flashes
(Number of times)
1
P1
Intake sensor error
P2
Pipe (TH2) sensor error
2
P9
Pipe (TH5) sensor error
Indoor/outdoor unit communication error
3
E6,E7
4
P4
Drain sensor error/Float switch connector (CN4F) open
P5
Drain pump error
5
Forced compressor stop(due to water leakage abnormality)
PA
6
P6
Freezing/Overheating protection operation
7
EE
Communication error between indoor and outdoor units
8
P8
Pipe temperature error
9
E4, E5
Remote controller signal receiving error
–
–
10
–
–
11
12
Fb
Indoor unit control system error (memory error, etc.)
14
PL
Refrigerant circuit abnormal
Remote controller transmission error
E0, E3
–
–
E1, E2
Remote controller control board error
[Output pattern B] Errors detected by unit other than indoor unit (outdoor unit, etc.)
Wireless remote controller Wired remote controller
Beeper sounds/OPERATION
Symptom
Check code
INDICATOR lamp flashes
(Number of times)
Indoor/outdoor unit communication error
1
E9
(Transmitting error) (Outdoor unit)
Compressor overcurrent interruption
2
UP
Open/short of outdoor unit thermistors
3
U3,U4
Compressor overcurrent interruption (When compressor locked)
4
UF
Abnormal high discharging temperature/49C operated/
5
U2
insufficient refrigerant
Abnormal high pressure (63H operated)/Overheating
U1,Ud
6
protection operation
Abnormal temperature of heat sink
U5
7
Outdoor unit fan protection stop
8
U8
9
Compressor overcurrent interruption/Abnormal of power module
U6
Abnormality of super heat due to low discharge temperature
10
U7
Abnormality such as overvoltage or voltage shortage and
11
U9,UH
abnormal synchronous signal to main circuit/Current sensor error
–
–
12
–
–
13
Others
Other errors (Refer to the technical manual for the outdoor unit.)
14
*1 If the beeper does not sound again after the initial 2 beeps to confirm the self-check start signal was received and
the OPERATION INDICATOR lamp does not come on, there are no error records.
*2 If the beeper sounds 3 times continuously “beep, beep, beep (0.4 + 0.4 + 0.4 sec.)” after the initial 2 beeps to confirm
the self-check start signal was received, the specified refrigerant address is incorrect.
• On wireless remote controller
The continuous buzzer sounds from receiving section of indoor unit.
Blink of operation lamp
• On wired remote controller
Check code displayed in the LCD.
OCH535
21
Remark
Remark
For details, check
the LED display
of the outdoor
controller board.
As for outdoor
unit, refer to
outdoor unit's
service manual.
• On wireless remote controller
The continuous buzzer sounds from receiving section of indoor unit.
Blink of operation lamp
• On wired remote controller
Check code displayed in the LCD.
• If the unit cannot be operated properly after test run, refer to the following table to find the cause.
Symptom
Wired remote controller
LED 1, 2 (PCB in outdoor unit)
For about 2
After LED 1, 2 are lighted, LED 2 is
PLEASE WAIT
minutes after turned off, then only LED 1 is
lighted. (Correct operation)
power-on
Cause
•For about 2 minutes following power-on,operation of the remote controller is not possible
due to system start-up. (Correct operation)
•Connector for the outdoor unit’s protection
Only LED 1 is lighted. →
device is not connected.
PLEASE WAIT → Error code
LED 1, 2 blink. •Reverse or open phase wiring for the outdoor
Subsequent to
unit’s power terminal block (L1, L2, L3)
about 2 minutes
after power-on Only LED 1 is lighted. →
Display messages do not
•Incorrect wiring between indoor and outdoor
appear even when operation
LED 1 blinks twice, units (incorrect polarity of S1, S2, S3)
switch is turned ON (operation
LED 2 blinks once. •Remote controller wire short
lamp does not light up).
On the wireless remote controller with condition above, following phenomena take place.
• No signals from the remote controller can be received.
• Operation lamp is blinking.
• The buzzer makes a short ping sound.
Note:
Operation is not possible for about 30 seconds after cancellation of function selection. (Correct operation)
For description of each LED (LED1, 2, 3) provided on the indoor controller, refer to the following table.
LED1 (power for microprocessor)
LED2 (power for remote controller)
Indicates whether control power is supplied. Make sure that this LED is
always lit.
Indicates whether power is supplied to the remote controller.
This LED lights only in the case of the indoor unit which is connected to the
outdoor unit refrigerant addresses “0”.
LED3 (communication between indoor and
outdoor units)
Indicates state of communication between the indoor and outdoor units.
Make sure that this LED is always blinking.
OCH535
22
Note: Refer to the manual of outdoor unit for the details of display
such as F, U, and other E.
9-3. SELF-DIAGNOSIS ACTION TABLE
Error Code
P1
Abnormal point and detection method
Room temperature thermistor (TH1)
1 The unit is in 3-minute resume
prevention mode if short/open of
thermistor is detected. Abnormal if the
unit does not reset normally after 3
minutes. (The unit returns to normal
operation, if it has been reset normally.)
2 Constantly detected during cooling,
drying, and heating operation.
Short: -90: or more
Open: -40: or less
Cause
1 Defective thermistor
characteristics
2 Contact failure of connector
(CN20) on the indoor controller
board (Insert failure)
3 Breaking of wire or contact
failure of thermistor wiring
4 Defective indoor controller
board
Countermeasure
1–3 Check resistance value of thermistor.
0: 15.0k"
10:
9.6k"
20:
6.3k"
30:
4.3k"
40:
3.0k"
If you put force on (draw or bend) the lead wire
while measuring resistance value of thermistor,
breaking of wire or contact failure can be
detected.
2 Check contact failure of connector (CN20)
on the indoor controller board. Refer to 9-7.
Turn the power on again and check restart
after inserting connector again.
4 Check room temperature display on remote
controller.
Replace indoor controller board if there
is abnormal difference with actual room
temperature.
Turn the power off, and on again to operate
after check.
P2
Pipe temperature thermistor/Liquid
(TH2)
1 The unit is in 3-minute resume
prevention mode if short/open of
thermistor is detected. Abnormal if the
unit does not reset normally after 3
minutes. (The unit returns to normal
operation, if it has been reset normally.)
2 Constantly detected during cooling,
drying, and heating (except defrosting)
operation
Short: 90: or more
Open: -40: or less
1 Defective thermistor
characteristics
2 Contact failure of connector
(CN44) on the indoor controller
board (Insert failure)
3 Breaking of wire or contact
failure of thermistor wiring
4 Defective refrigerant circuit is
causing thermistor temperature
of 90: or more or -40: or
less.
5 Defective indoor controller
board
1–3 Check resistance value of thermistor.
For characteristics, refer to (P1) above.
2 Check contact failure of connector (CN44)
on the indoor controller board. Refer to 9-7.
Turn the power on and check restart after
inserting connector again.
4 Check pipe <liquid> temperature with remote
controller in test run mode. If pipe <liquid>
temperature is extremely low (in cooling
mode) or high (in heating mode), refrigerant
circuit may have defective.
5 Check pipe <liquid> temperature with
remote controller in test run mode. If there is
extremely difference with actual pipe <liquid>
temperature, replace indoor controller board.
Turn the power off, and on again to operate
after check.
P4
P5
Contact failure of drain float switch
1 Contact failure of connector
(CN4F)
(Insert failure)
• Extract when the connector of drain float
switch is disconnected.
(3 and 4 of connector CN4F is not
2 Defective indoor controller
short-circuited.)
board
• Constantly detected during operation
1 Check contact failure of float switch connector.
Turn the power on again and check after
inserting connector again.
2 Operate with connector (CN4F) shortcircuited.
Replace indoor controller board if abnormality
reappears.
Drain over flow protection operation
1 Suspensive abnormality, if drain float
switch is detected to be underwater for
1 minute and 30 seconds continuously
with drain pump on.
Compressor and indoor fan will be
turned off.
2 Drain pump is abnormal if the condition
above is detected during suspensive
abnormality.
3 Constantly detected during drain pump
operation
1 Check if drain pump works.
2 Check drain function.
1 Malfunction of drain pump
2 Defective drain
Clogged drain pump
Clogged drain pipe
3 Defective drain float switch
Jamming of the drain float
switch or malfunction of moving
parts causing the drain float
switch to be detected under
water (Switch On)
4 Defective indoor-controller
board
3 Remove drain float switch connector CN4F
and check if it is short (Switch On) with the
moving part of float switch UP, or OPEN with
the moving part of float switch down.
Replace float switch if it is short with the
moving part of float switch down.
4 Replace indoor controller board if it is shortcircuited between 3-4 of the drain float
switch connector CN4F and abnormality
reappears.
It is not abnormal if there is no problem about
the above-mentioned
Turn the power off, and on again to operate
after check.
OCH535
23
Error Code
P6
P8
Abnormal point and detection method
Freezing/overheating protection is operating
1 Freezing protection (Cooling mode)
The unit is in 6-minute resume prevention mode if pipe <liquid or condenser/
evaporator> temperature stays under
-15: for 3 minutes, 3 minutes after the
compressor started. Abnormal if it stays
under -15: for 3 minutes again within
16 minutes after 6-minute resume prevention mode.
2 Overheating protection (Heating mode)
The units is in 6 minute resume
prevention mode if pipe <liquid or
condenser/evaporator> temperature
is detected as over 70: after the
compressor started. Abnormal if the
temperature of over 70: is detected
again within 30 minutes after 6 minute
resume prevention mode.
Pipe temperature
<Cooling mode>
Detected as abnormal when the pipe temperature is not in the cooling range 3 minutes after compressor start and 6 minutes
after the liquid or condenser/evaporator
pipe is out of cooling range.
Note 1) It takes at least 9 minutes to
detect.
Note 2) Abnormality P8 is not detected in
drying mode.
Cooling range : -3 °C ] (TH-TH1)
TH: Lower temperature between: liquid
pipe temperature (TH2) and condenser/evaporator temperature (TH5)
TH1: Intake temperature
<Heating mode>
When 10 seconds have passed after the
compressor starts operation and the hot
adjustment mode has finished, the unit is
detected as abnormal when condenser/
evaporator pipe temperature is not in heating range within 20 minutes.
Cause
(Cooling or drying mode)
1 Clogged filter (reduced airflow)
2 Short cycle of air path
3 Low-load (low temperature)
operation out of the tolerance
range
4 Defective indoor fan motor
• Fan motor is defective.
• Indoor controller board is defective.
4 Refer to 9-6.
5 Defective outdoor fan control
6 Overcharge of refrigerant
7 Defective refrigerant circuit
(clogs)
5 Check outdoor fan motor.
67 Check operating condition of refrigerant
circuit.
(Heating mode)
1 Clogged filter (reduced airflow)
2 Short cycle of air path
3 Over-load (high temperature)
operation out of the tolerance
range
4 Defective indoor fan motor
• Fan motor is defective.
• Indoor controller board is defective.
5 Defective outdoor fan control
6 Overcharge of refrigerant
7 Defective refrigerant circuit
(clogs)
8 Bypass circuit of outdoor unit
is defective.
(Heating mode)
1 Check clogs of the filter.
2 Remove blockage.
1 Slight temperature difference
between indoor room
temperature and pipe <liquid
or condenser/evaporator>
temperature thermistor
• Shortage of refrigerant
• Disconnected holder of
pipe <liquid or condenser/
evaporator> thermistor
• Defective refrigerant circuit
2 Converse connection of
extension pipe (on plural units
connection)
3 Converse wiring of indoor/
outdoor unit connecting wire
(on plural units connection)
4 Defective detection of indoor
room temperature and pipe
<condenser/evaporator>
temperature thermistor
5 Stop valve is not opened
completely.
1~4 Check pipe <liquid or condenser/evaporator> temperature with room temperature
display on remote controller and outdoor
controller circuit board.
Pipe <liquid or condenser/evaporator>
temperature display is indicated by setting SW2 of outdoor controller circuit
board as follows.
Note 3) It takes at least 27 minutes to
detect abnormality.
Note 4) It excludes the period of defrosting.
(Detection restarts when defrosting
mode is over.)
Heating range : 3 °C [ (TH5-TH1)
OCH535
Countermeasure
(Cooling or drying mode)
1 Check clogs of the filter.
2 Remove blockage.
24
4 Refer to 9-6.
5 Check outdoor fan motor.
6~8 Check operating condition of refrigerant
circuit.
(
Conduct temperature check with outdoor
controller circuit board after connecting
‘A-Control Service Tool(PAC-SK52ST)’.
)
23 Check converse connection of extension
pipe or converse wiring of indoor/outdoor
unit connecting wire.
Error Code
P9
Abnormal point and detection method
Pipe temperature thermistor/
Condenser-Evaporator (TH5)
1 The unit is in 3-minute resume protection mode if short/open of thermistor is
detected. Abnormal if the unit does not
get back to normal within 3 minutes. (The
unit returns to normal operation, if it has
been reset normally.)
2 Constantly detected during cooling,
drying, and heating operation (except
defrosting)
Short: 90: or more
Open: -40: or less
Remote controller transmission
error(E0)/signal receiving error(E4)
1 Abnormal if main or sub remote controller cannot receive any transmission
normally from indoor unit of refrigerant
address “0” for 3 minutes.
(Error code : E0)
2 Abnormal if sub remote controller could
not receive any signal for 2 minutes.
(Error code: E0)
E0
or
E4
E3
or
E5
1 Abnormal if indoor controller board can
not receive any data normally from
remote controller board or from other
indoor controller board for 3 minutes.
(Error code: E4)
2 Indoor controller board cannot receive
any signal from remote controller for 2
minutes. (Error code: E4)
Countermeasure
Cause
1 Defective thermistor
1–3 Check resistance value of thermistor.
characteristics
For characteristics, refer to (P1) above.
2 Contact failure of connector
(CN44) on the indoor controller 2 Check contact failure of connector (CN44)
on the indoor controller board.
board (Insert failure)
Refer to 9-7.
3 Breaking of wire or contact
Turn the power on and check restart after
failure of thermistor wiring
inserting connector again.
4 Temperature of thermistor is
4 Operate in test run mode and check pipe
90: or more or -40: or less
<condenser/evaporator> temperature with
caused by defective refrigerant
outdoor controller circuit board. If pipe <concircuit.
denser/evaporator> temperature is extremely
low (in cooling mode) or high (in heating
5 Defective indoor controller
mode), refrigerant circuit may have defect.
board
5 Operate in test run mode and check pipe
<condenser/evaporator> temperature
with outdoor control circuit board. If there
is extreme difference with actual pipe
<condenser / evaporator> temperature,
replace indoor controller board.
There is no abnormality if none of above
comes within the unit.
Turn the power off and on again to operate.
1 Contact failure at transmission
wire of remote controller
2 All remote controllers are set
as “sub” remote controller.
In this case, E0 is displayed
on remote controller, and E4
is displayed at LED (LED1,
LED2) on the outdoor controller
circuit board.
3 Miswiring of remote controller
4 Defective transmitting receiving
circuit of remote controller
5 Defective transmitting receiving
circuit of indoor controller board
of refrigerant addresses “0”.
6 Noise has entered into the
transmission wire of remote
controller.
Remote controller transmission
error(E3)/signal receiving error(E5)
1 Abnormal if remote controller could not
find blank of transmission path for 6 seconds and could not transmit.
(Error code: E3)
2 Remote controller receives transmitted
data at the same time and compares the
received and transmitted data. Abnormal
if these data are judged to be different
30 continuous times. (Error code: E3)
1 2 remote controllers are set as
“main.”
(In case of 2 remote controllers)
2 Remote controller is connected
with 2 indoor units or more.
3 Repetition of refrigerant
address
4 Defective transmitting receiving
circuit of remote controller
1 Abnormal if indoor controller board could 5 Defective transmitting receiving
not find blank of transmission path.
circuit of indoor controller board
(Error code: E5)
6 Noise has entered into trans2 Indoor controller board receives transmission wire of remote controlmitted data at the same time and comler.
pares the received and transmitted data.
Abnormal if these data are judged to
be different 30 continuous times. (Error
code: E5)
OCH535
25
(
In case of checking pipe temperature
with outdoor controller circuit board,
be sure to connect A-control service
tool (PAC-SK52ST).
)
1 Check disconnection or looseness of indoor
unit or transmission wire of remote controller.
2 Set one of the remote controllers “main”
if there is no problem with the action above.
3 Check wiring of remote controller.
• Total wiring length: max. 500m
(Do not use cable x 3 or more.)
• The number of connecting indoor units:
max. 16 units
• The number of connecting remote controller: max. 2 units
When it is not the above-mentioned problem of
1~3
4 Diagnose remote controllers.
a) When “RC OK” is displayed,
Remote controllers have no problem.
Turn the power off, and on again to check.
If abnormality generates again, replace
indoor controller board.
b) When “RC NG” is displayed,
Replace remote controller.
c) When “RC E3” or “ERC 00-66” is displayed, noise may be causing abnormality.
* If the unit is not normal after replacing
indoor controller board in group control,
indoor controller board of address “0” may
be abnormal.
1 Set a remote controller to main, and the
other to sub.
2 Remote controller is connected with only one
indoor unit.
3 The address changes to a separate setting.
4~6 Diagnose remote controller.
a) When “RC OK” is displayed, remote controllers have no problem.
Turn the power off,and on again to check.
When becoming abnormal again, replace
indoor controller board.
b) When “RC NG” is displayed, replace
remote controller.
c) When “RC E3” or “ERC 00-66” is displayed, noise may be causing abnormality.
Error Code
E6
E7
Fb
E1
or
E2
PA
Abnormal point and detection method
Indoor/outdoor unit communication
error (Signal receiving error)
1 Abnormal if indoor controller board
cannot receive any signal normally for 6
minutes after turning the power on.
2 Abnormal if indoor controller board
cannot receive any signal normally for 3
minutes.
3 Consider the unit abnormal under the
following condition: When 2 or more
indoor units are connected to an outdoor
unit, indoor controller board cannot
receive a signal for 3 minutes from
outdoor controller circuit board, a signal
which allows outdoor controller circuit
board to transmit signals.
Countermeasure
Cause
1 Contact failure, short circuit or, * Check LED display on the outdoor control
circuit board. (Connect A-control service
miswiring (converse wiring) of
tool, PAC-SK52ST.)
indoor/outdoor unit connecting
Refer to outdoor unit service manual.
wire
1 Check disconnection or looseness of indoor/
2 Defective transmitting receiving
outdoor unit connecting wire of indoor unit or
circuit of indoor controller board
outdoor unit.
3 Defective transmitting receiving
Check all the units in case of twin triple
circuit of indoor controller board
indoor unit system.
4 Noise has entered into indoor/ 2-4 Turn the power off, and on again to
check. If abnormality generates again,
outdoor unit connecting wire.
replace indoor controller board or outdoor
controller circuit board.
* Other indoor controller board may have defect
in case of twin triple indoor unit system.
Indoor/outdoor unit communication
1 Defective transmitting receiving 1-3 Turn the power off, and on again to check.
error (Transmitting error)
circuit of indoor controller board
If abnormality generates again, replace
Abnormal if “1” receiving is detected 30
indoor controller board.
2 Noise has entered into power
times continuously though indoor controller
supply.
board has transmitted “0”.
3 Noise has entered into outdoor
control wire.
Indoor controller board
Abnormal if data cannot be read normally
from the nonvolatile memory of the indoor
controller board.
1 Defective indoor controller
board
Remote controller control board
1 Defective remote controller
1 Abnormal if data cannot be read normally from the nonvolatile memory of the
remote controller control board.
(Error code: E1)
1 Replace indoor controller board.
1 Replace remote controller.
2 Abnormal if the clock function of remote
controller cannot be operated normally.
(Error code: E2)
Forced compressor stop
(due to water leakage abnormality)
1 The unit has a water leakage abnormality when the following conditions, a)
and b), are satisfied while the abovementioned detection is performed.
a) The intake temperature subtracted
with liquid pipe temperature detects
to be less than -10: for a total of
30 minutes. (When the drain sensor
is detected to be NOT soaked in the
water, the detection record of a) and b)
will be cleared.)
b) Drain float switch detects to be in the
water for more than 15 minutes.
*Once the water leakage abnormality is
detected, abnormality state will not be
released until the main power is reset.
1 Drain pump trouble
1 Check the drain pump.
2 Drain defective
· Drain pump clogging
· Drain pipe clogging
2 Check whether water can be drained.
3 Open circuit of float switch
3 Check the resistance of the float switch.
4 Contact failure of float switch
connector
4 Check the connector contact failure.
5 Dew condensation on float
switch
· Drain water descends along
lead wire.
· Drain water waving due to
filter clogging.
5 Check the float switch leadwire mounted.
Check the filter clogging.
6 Extension piping connection
difference at twin, triple, quadruple system.
6 Check the piping connection.
7 Check the indoor/outdoor connecting wires.
7 Miswiring of indoor/ outdoor
connecting at twin, triple, quadruple system.
8 Room temperature thermistor/ 8 Check the room temperature display of
remote controller.
liquid pipe temperature thermisCheck the indoor liquid pipe temperature dis
tor detection is defective.
play of outdoor controller board.
OCH535
26
Abnormal point and detection method
Error Code
PL
Abnormal refrigerant circuit
During Cooling, Dry, or Auto Cooling
operation, when the following are
regarded as failures when detected for
one second.
a)The compressor continues to run for 30
or more seconds.
b)The liquid pipe temperature or the
condense/evaporator temperature is
75°C or more.
* These detected errors will not be
cancelled until the power source is
reset.
OCH535
Cause
1 Abnormal operation of 4-way
valve
2 Disconnection of or leakage in
refrigerant pipes
3 Air into refrigerant piping
4 Abnormal operation (no rotation)
of indoor fan
· Defective fan motor.
· Defective indoor control board.
5 Defective refrigerant circuit
(clogging)
27
Countermeasure
1 When this error occurs, be sure to replace
the 4-way valve.
2 Check refrigerant pipes for disconnection or
leakage.
3 After the recovery of refrigerant, vacuum dry
the whole refrigerant circuit.
4 Refer to section 9-6-2.
5 Check refrigerant circuit for operation.
* To avoid entry of moisture or air into
refrigerant circuit which could cause
abnormal high pressure, purge air in
refrigerant circuit or replace refrigerant.
9-4. TROUBLESHOOTING OF PROBLEMS
Phenomena
(1) LED2 on indoor controller board
is off.
Note: Refer to the manual of outdoor unit for the detail of remote
controller.
Cause
• When LED1 on indoor controller board is also off.
1 Power supply of rated voltage is not supplied to outdoor unit.
2 Defective outdoor controller circuit board
3 Power supply of 220~240V is not supplied to indoor
unit.
4 Defective indoor controller board
(For the separate indoor/outdoor unit power supply system)
1 Power supply of 220~240V AC is not supplied to
indoor unit.
2 The connectors of the optional replacement kit are
not used.
3 Defective indoor controller board
Countermeasure
1 Check the voltage of outdoor power
supply terminal block (L, N) or (L3, N).
• When AC 220~240V is not detected,
check the power wiring to outdoor unit
and the breaker.
• When AC 220~240V is detected, check
2 (below).
2 Check the voltage between outdoor
terminal block S1 and S2.
• When AC 220~240V is not detected,
—check the fuse on outdoor controller
circuit board.
—check the wiring connection.
• When AC 220~240V is detected, check
3 (below).
3 Check the voltage between indoor
terminal block S1 and S2.
• When AC 220~240V is not detected,
check indoor/outdoor unit connecting
wire for miswiring.
• When AC 220~240V is detected, check
4 (below).
4 Check the fuse on indoor controller
board.
Check the wiring connection.
If no problem are found, indoor controller
board is defective.
1 Check the voltage of indoor power supply
terminal block (L,N).
• When AC220~240V is not detected,
check the power supply wiring.
• When AC220~240V is detected, check
2 (below).
2 Check that there is no problem in the
method of connecting the connectors.
• When there are problems in the method
of connecting the connectors, connect
the connector correctly referring to
installation manual of an optional kit.
• When there is no problem in the method
of connecting the connectors, check 3
(below).
3 Check the fuse on indoor controller
board.
Check the wiring connection.
If no problem are found, indoor controller
board is defective.
• When LED1 on indoor controller board is lit.
1 Check again the setting of refrigerant
1 Mis-setting of refrigerant address for outdoor unit
address for outdoor unit.
(There is no unit corresponding to refrigerant address
Set the refrigerant address to “0”.
“0”.)
(For grouping control system under which
2 or more outdoor units are connected,
set one of the units to “0”.)
Set refrigerant address using SW1 (3-6)
on outdoor controller circuit board.
OCH535
28
Note: Refer to the manual of outdoor unit for the detail of remote
controller.
Phenomena
(2) LED2 on indoor controller board
is blinking.
Cause
Countermeasure
• When LED1 on indoor controller board is also blinking. Check indoor/outdoor unit connecting wire
Connection failure of indoor/outdoor unit connecting for connection failure.
wire
• When LED1 is lit.
1 Check the connection of remote controller
wires in case of twin triple indoor unit
1 Miswiring of remote controller wires
Under twin triple indoor unit system, 2 or more indoor
system. When 2 or more indoor units are
units are wired together.
wired in one refrigerant system, connect
remote controller wires to one of those
units.
2 Refrigerant address for outdoor unit is wrong or not 2 Check the setting of refrigerant address
in case of grouping control system.
set.
If there are some units whose refrigerant
Under grouping control system, there are some units
addresses are 0 in one group, set one of
whose refrigerant address is 0.
the units to 0 using SW1 (3-6) on outdoor
controller circuit board.
3 Short-cut of remote controller wires
34 Remove remote controller wires and
check LED2 on indoor controller board.
4 Defective remote controller
• When LED2 is blinking, check the shortcut of remote controller wires.
• When LED2 is lit, connect remote
controller wires again and:
if LED2 is blinking, remote controller
is defective; if LED2 is lit, connection
failure of remote controller terminal
block etc. has returned to normal.
(3) Upward/downward vane perform- 1 The vane is not downward during defrosting and heat 1 Normal operation (The vane is set to
ance failure
preparation and when the thermostat is OFF in HEAT
horizontal regardless of remote control.)
mode. (Working of COOL protection function)
2 Vane motor does not rotate.
2 Check 2 (left).
• Defective vane motor
• Check the vane motor. (Refer to “How
• Breaking of wire or connection failure of connector
to check the parts”.)
• Check for breaking of wire or connection failure of connector.
3 Upward/downward vane does not work.
3 Normal operation (Each connector on
• The vane is set to fixed position.
vane motor side is disconnected or
setting the fixed vanes by wired remote
controller.)
(4) Receiver for wireless remote
controller
OCH535
1 Replace batteries of wireless remote
controller.
2~4
2 Contact failure of connector (CNB) on wireless
Check contact failure of each connector.
remote controller board
If no problems are found of connector,
(Insert failure)
replace indoor controller board.
3 Contact failure of connector (CN90) on indoor conWhen the same trouble occurs even
troller board (Insert failure)
if indoor controller board is replaced,
4 Contact failure of connector between wireless remote
replace wireless remote controller
controller board and indoor controller board
board.
1 Weak batteries of wireless remote controller.
29
9-5. EMERGENCY OPERATION
9-5-1. When wireless remote controller fails or its battery is exhausted
When the remote controller cannot be used
When the batteries of the remote controller run out or the remote controller malfunctions, the emergency operation can be done using the emergency buttons on the grille.
DEFROST/STAND BY lamp
Operation lamp
Emergency operation switch (heating)
Emergency operation switch (cooling)
Receiver
Starting operation
for more than 2
• To operate the cooling mode, press the
button
seconds.
for more than 2
• To operate the heating mode, press the
button
seconds.
* Lighting of the Operation lamp means the start of operation.
Details of EMERGENCY MODE are as shown below.
Operation mode
Set temperature
Fan speed
Air ow direction
Stopping operation
• To stop operation, press the
COOL
24°C
High
Horizontal
button
HEAT
24°C
High
Downward 5
or the
button
.
9-5-2. When wired remote controller or indoor unit microprocessor fails
1. When the wired remote control or the indoor unit microprocessor has failed, but all other components work properly,
if you set the switch (SWE) on the indoor controller board ON, the indoor unit will begin Emergency Operation.
When Emergency Operation is activated, the indoor unit operates as follows:
(1) Indoor fan is running at high speed. (2) Drain pump is operating.
* Note on the wireless remote control
When the remote control does not function, it is possible to activate.
Emergency Operation by using the indoor unit Emergency operation switch (SW1, SW2 of the wireless signal
receiver board).
However, if the indoor unit microprocessor has failed, it is nesessary to proceed with points 2 and 3 below as in the
case of the wired remote control.
2. When you activate Emergency operation of the cooling or heating, you have to set the switch (SWE) on the indoor
controller board and activate Emergency operation of the outdoor unit.
For details on how to activate Emergency operation of the outdoor unit, refer to the outdoor unit wiring diagram.
Note: Emergency operation will not work unless outdoor unit is PU series.
3. Before you activate Emergency operation, check the following points:
(1) Emergency operation cannot be activated when:
• the outdoor unit malfunctions. • the indoor fan malfunctions.
• the malfunction of drain pump is detected during self-diagnosing.
(2) Emergency operation becomes continuous only by switching the power source on/off.
ON/OFF on the remote control or temperature control etc. does not function.
(3) Avoid operating for a long time when the outdoor unit begins defrosting
while Emergency operation of the heating is activated, because it will start to blow cold air.
(4) Emergency cooling should be limited to 10 hours maximum (The indoor unit heat exchanger may freeze).
(5) After Emergency operation has been deactivated, set the switches etc. to their original positions.
(6) Movement of the vanes does not work in Emergency operation, therefore
you have to slowly set them manually to the appropriate position.
OCH535
30
9-6. HOW TO CHECK THE PARTS
PLA-ZRP35BA.UK
PLA-ZRP50BA.UK
PLA-ZRP71BA.UK
PLA-ZRP125BA.UK
PLA-ZRP60BA.UK
PLA-ZRP140BA.UK
Parts name
Room temperature
thermistor
(TH1)
Pipe temperature
thermistor/liquid(TH2)
Condenser/Evaporator
temperature thermistor
(TH5)
Vane motor (MV)
Check points
Disconnect the connector then measure the resistance with a tester.
(At the ambient temperature of 10~30)
Normal
Abnormal
4.3k~9.6k
Open or short
(Refer to the thermistor.)
Measure the resistance between the terminals with a tester.
(At the ambient temperature of 20~30)
White
Connector
MV
Orange
Red - Yellow
(-, -, -, -)
Red - Blue
(-
, -, -, -)
Normal
Abnormal
300
Open or short
Red - Orange (-, -, -, -)
Red
Yellow
Blue
Drain pump (DP)
YLW
1
3
YLW
Drain float switch (FS)
Moving part
1
2
3
Red - White
(-, -, -
, -)
Measure the resistance between the terminals with a tester.
(Winding temperature 20)
Normal
Abnormal
290 Open or short
Measure the resistance between the terminals with a tester.
State of moving part
Normal
Abnormal
UP
Short
Other than short
DOWN
Open
Other than open
Switch
Magnet
4
i-see sensor
(Option)
Moving
Part
Turn on the indoor unit with the black plastic tape on the outside of
i-see sensor controller board.
With electricity being turned on, measure the power voltage between connectors with tester.
i-see sensor rotates and pull out the connector of motor for i-see sensor.
Do not disassemble corner panel
with i-see sensor.
Black plastic tape
4 3 2 1
i-see sensor (At the ambient temperature of 10~40)
i-see sensor connector
4 3 2 1
Blue BlackPink Brown
(–)—(+)
Normal
DC 1.857V ~ 3.132V
Abnormal
Other than the normal
(+)—(–)
DC 0.939V ~ 1.506V
Other than the normal
NOTE : Be careful not to discharge static electricity into electronics.
Vane motor for
i-see sensor (Option)
Measure the resistance between the terminals with a tester.
(At the ambient temperature of 20~30)
Connector
White
MV
Red - Blue
Orange
Red - Orange
Red
Blue
OCH535
Yellow
Normal
Abnormal
250 Open or short
Red - Yellow
Red - White
31
9-6-1. Thermistor
< Thermistor for lower temperature >
<Thermistor Characteristic graph>
Room temperature thermistor (TH1)
Pipe temperature thermistor/liquid (TH2)
Condenser/evaporator temperature
thermistor (TH5)
40
Resistance (k)
Thermistor for
lower temperature
50
Thermistor R0=15k' ± 3%
Fixed number of B=3480 ± 2%
Rt=15exp { 3480(
0:
10:
20:
25:
30:
40:
1
273+t
1 )}
273
15k'
9.6k'
6.3k'
5.4k'
4.3k'
3.0k'
30
20
10
0
-20 -10 0 10 20 30 40 50
Temperature ()
9-6-2. DC Fan motor (FAN MOTOR/INDOOR CONTROLLER BOARD)
Check method of DC fan motor (fan motor / indoor controller circuit board)
Notes
· High voltage is applied to the connector (CNMF) for the fan motor. Pay attention to the service.
· Do not pull out the connector (CNMF) for the motor with the power supply on.
(It causes trouble of the indoor controller circuit board and fan motor.)
Self check
Symptom : The indoor fan cannot turn around.
Indoor controller board fuse check
Is the fuse normal?
Is the resistance
between the terminals of
drain pump normal?
No
Yes
Replace the fan motor.
Replace the indoor controller board.
No
Wiring contact check
Contact of fan motor connector (CNMF)
Is there contact failure?
Yes
Replace the drain pump.
Yes
Wiring recovery
No
Power supply check (Remove the connector (CNMF))
Measure the voltage in the indoor controller circuit board.
TEST POINT : VDC (between 1 (+) and 4 (-) of the fan connector): VDC DC 310~340 V
TEST POINT : VCC (between 5 (+) and 4 (-) of the fan connector): VCC DC 15 V
Is the voltage normal?
Yes
Replace the fan motor.
No
Check the operation of fan.
Replace indoor
controller board
Check the operation
NG
OK
Replace indoor controller board.
END
NG
Replace the fan motor.
OCH535
32
OK
END
9-7. TEST POINT DIAGRAM
Indoor controller board
PLA-ZRP35BA.UK
PLA-ZRP71BA.UK
PLA-ZRP50BA.UK
PLA-ZRP125BA.UK
LED3
Transmission (Indoor/outdoor)
CN90
Connect to the wireless
remote controller board
(CNB)
PLA-ZRP60BA.UK
PLA-ZRP140BA.UK
CN3G
Connect to the auto grille controller board (CN3G)
13V pulse output
CNV
Vane motor output (MV)
12V pulse output
CN4Y
i-see sensor
SW1
Model selection
CN6Y
i-see sensor motor output
12V DC pulse output
SW2
Capacity setting
CN2L
Connector (LOSSNAY)
CN105
Jumper wire J41,J42
Pair No. setting for wireless
remote controller
LED2
Power supply (R.B)
CN51
Centrally control
1-2 : Control signal
13V pulse input (1:+)
3-4 : Operation indicator
13VDC (3:+)
3-5 : Malfunction indicator
13VDC (3:+)
CN4F
Drain float switch (FS)
CN44
Pipe temperature
thermistor
1-2 : Liquid (TH2)
3-4 : Condenser/Evaporator (TH5)
CN41
Connector
(HA terminal-A)
CN32
Connector
(Remote switch)
CN20
Room temperature
thermistor (TH1)
SWE
Emergency operation
CN3C
Transmission
(Indoor/outdoor)
(0~24V DC)
LED1
Power supply (I.B)
CN22
Connect to the terminal
block (TB5)
(Remote controller connecting wire)
(10.4~14.6V DC)
CNMF
Fan motor
1-4: DC 310~340V
5-4: DC15V
VCC : Voltage between pins of
C955 15VDC
(Same as 5(+)–4(-) of CNMF)
CNP
Drain-pump output (DP)
(220-240V AC)
CN01
Connect to the Terminal Block (TB4)
(Indoor/outdoor connecting line)
Between 3 and 5
220-240V AC
CNAC
Connect to the auto grille
controller board (CN3A)
(220-240V AC)
OCH535
FUSE 6.3A /250V
33
9-8. FUNCTIONS OF DIP SWITCH AND JUMPER WIRE
Each function is controlled by the dip switch and the jumper wire on control P.C. board.
The black square (■) indicates a switch position
Jumper wire ( : Short
: Open)
Jumper wire
Functions
SW1
Model
settings
Setting by the dip switch and jumper wire
1 2 3 4 5
MODELS
PLA-ZRP35BA
PLA-ZRP50BA
SW2
Capacity
settings
PLA-ZRP60BA
PLA-ZRP71BA
PLA-ZRP125BA
PLA-ZRP140BA
J41
J42
Pair number
setting with
wireless
remote
controller
JP1
Unit type
setting
JP3
Indoor
controller
board type
setting
OCH535
ON
OFF
SETTING
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
<Initial setting>
Wireless remote controller: 0
Control PCB: (for both J41 and J42)
4 pair number settings are supported.
The pair number settings of the wireless remote
controller and indoor control PCB (J41/J42) are
given in the table on the left.
(' ' in the table indicates the jumper wire is disconnected.)
Wireless remote Control PCB setting
controller setting
J41
J42
0
1
2
3~9
Model
Without TH5
With TH5
Remarks
JP1
Indoor controller board type
For product
Service parts
There is no jumper (JP1) because these models
have the cond./eva. temperature thermistor (TH5).
JP3
34
10
SPECIAL FUNCTION
10-1. HOW TO PERFORM THE UP/DOWN OPERATION OF THE AIR INTAKE GRILLE
10-1-1. Setting up the lowering distance of air intake grille
You can set up 8 different stages of lowering distance for
the air intake grille according to the set up location if desired.
Unit
Decorative
panel
* As a factory default, the decorative panel will automatically
stop at 1.6 m from the ceiling level. The distance is a
rough indication, check by actually lowering it.
1) Take the cover off the electric box of the decorative panel. (2 screws)
2) Set up the dip switches of SW22 or SW2 on the control board of the
decorative panel as followed.
Cover for
Electric Box of
the decorative
panel
Control board of
the decorative
panel
SW 22 or SW2
Screws
Dip SW 22
Dip SW 2
The black square (■) indicates a switch position.
Lowering distance
SW22
(Rough indication
(Lowering distance)
of the ceiling height)
The black square (■) indicates a switch position.
Lowering distance
SW22
(Rough indication
(Lowering distance)
of the ceiling height)
Lowering distance
SW2
(Rough indication
(Lowering distance)
of the ceiling height)
Lowering distance
SW2
(Rough indication
(Lowering distance)
of the ceiling height)
Initial setting
Initial setting
1.2m
(~ 2.4m)
1.6m
(2.4m ~ 2.8m)
1.2m
(~ 2.4m)
1.6m
(2.4m ~ 2.8m)
2.0m
(2.8m ~ 3.2m)
2.4m
(3.2m ~ 3.6m)
2.0m
(2.8m ~ 3.2m)
2.4m
(3.2m ~ 3.6m)
2.8m
(3.6m ~ 4.0m)
3.2m
(4.0m ~ 4.4m)
2.8m
(3.6m ~ 4.0m)
3.2m
(4.0m ~ 4.4m)
3.6m
(4.4m ~ 4.8m)
4.0m
(4.8m ~ 5.2m)
3.6m
(4.4m ~ 4.8m)
4.0m
(4.8m ~ 5.2m)
* Airflow outreach distance is different depending on indoor units and
air volume (ceiling height), so airflow may not reach the indicated
ceiling height as shown in the above table.
3) Put the cover back on the electric box of the decorative panel.
OCH535
35
* Airflow outreach distance is different depending on indoor units and
air volume (ceiling height), so airflow may not reach the indicated
ceiling height as shown in the above table.
10-1-2. How to perform the up/down operation using wireless remote controller
Warning:
Ensure that the air-conditioner is not running.
• Otherwise, it may cause an injury or a failure.
1) Ensure that the air-conditioner is not running.
2) Press the "Down" button to lower the air intake grille.
* By default, the air intake grille will automatically stop at a lowering distance of 1.6 m from the ceiling level.
The distance can be changed to 1.2 m, 2.0 m, 2.4 m, 2.8 m, 3.2 m, 3.6 m and 4.0 m. These should be used
only as a guide. You should lower the air intake grille yourself to check the exact distance.
* When you want to stop the air intake grille while it is lowering, press the "Stop" or "Up" button on the remote
controller to stop at that position.
3) Remove the filter or air intake grille and clean them.
Wireless remote
controller for
4) Attach the filter and air intake grille.
Automatic Filter
5) Press the "Up" button on the remote controller to put the air intake grille in place.
Elevation Panel
* If the air intake grille is not placed in the correct position at a time, the operation is automatically retried.
* When you want to stop the air intake grille while it is rising, press the "Stop" or "Down" button on the remote controller
to stop at that position.
10-1-3. How to perform the up/down operation using wired remote controller (PAR-30MAA / PAR-31MAA)
1 Select "Maintenance" from the Main menu, and press the
button.
Select "Auto descending panel" with the F1 or F2 button, and press the
button.
Maintenance menu
Auto descending panel
Manual vane angle
Main menu:
Cursor
* When using the auto descending panel, always set the "Address" and "Unit
No." with "Service" – "Function setting".
F1
2 Move the cursor to "Ref. address", "Unit No." or "Operation" with the F1
button to select.
Select the refrigerant address and the unit number for the units to whose falls
panel, with the F2 or F3 button, and press the
button.
• Ref. address: Refrigerant address
• Unit No.: 1, 2, 3, 4, All
• Operation: Down / Up
F2
F3
F4
Auto descending panel
Ref. address
Unit No.
All
Operation
Down / Up
Keep clear, panel descending.
Press Check for Unit No.
Input display:
Cur.
Address
Check
F1
F2
F3
F4
Press the F4 button to confirm the unit.
<Confirmation of target unit>
If the unit being set is unknown, make the setting and then press the F4 button to conf rm.
The air conditioner which is blowing downward is the target air conditioner.
Navigating through the screens
• To go back to the Main menu ..................
button
• To return to the previous screen ...............
button
OCH535
Auto descending panel
Ref. address
Unit No.
All
Operation
Down / Up
Panel will stop in 30 sec.
Keep clear, panel descending.
Cur.
Address
Check
F1
36
F2
F3
F4
10-1-4. How to perform the up/down operation using wired remote controller (PAR-21MAA)
■General Operation
* Raise or lower all the air intake grilles managed by the remote controller at the same time.
Install the remote controller in a place where you can observe all the air-conditioners. Otherwise, the lowering grille may make
contact with something and cause damage to it.
1) Ensure that the air-conditioner is not running.
* The up/down operation mode is only available when the
airconditioner is "OFF".
Warning:
Ensure that the air-conditioner is not running.
• Otherwise, it may cause an injury or a failure.
2) Press both the "FILTER" and "Ventilation" buttons simultaneously for 2 seconds or more to enter the up/down
operation mode.
"Up/down operation
mode" display
3) Press the TEMP. ( ) button. After a while, the air intake grille will begin lowering.
"Stand by for lowering"
display
[ Note: ]
Alternately
• You cannot stop the operation while the air intake grille is lowering.
* If you press the ( ) button while the air intake grille is moving down, the air intake grille
may stop lowering, but it will not stop immediately.
• By default, the air intake grille will automatically stop at the lowering distance of 1.6 m
from the ceiling level.
* The distance can be changed to 1.2 m, 2.0 m, 2.4 m, 2.8 m, 3.2 m, 3.6 m, and 4.0 m.
These should be used only as a guide. You should lower the air intake grille yourself to check
the exact distance.
the air intake grille
"Lowering" display
(blinking)
"Stopped" display
(when finished lowering)
4) Remove the filter and/or air intake grille to clean them.
5) Press the TEMP. ( ) button. After a while, the air intake grille will begin to rise and then be put back into place.
"Stand by for raising" display
Alternately
[ Note: ]
"Raising" display (blinking)
• You cannot stop the operation while the air intake grille is rising.
* If you press the ( ) button while the intake grille is moving up, the air
intake grille may stop rising, but it will not stop immediately.
"Stopped" display (when the air intake
grille has been put back into place)
6) Exit the up/down mode either by pressing the "ON/OFF" button or by pressing both the "FILTER" and "Ventilation"
buttons simultaneously for 2 seconds or more.
* After exiting the up/down mode, wait for
about 30 seconds to perform the next
Operation status
operation. The remote controller will not
display
accept any operation for that period.
Button to exit the up/down
operation mode
Down/Up
buttons
TEMP.
MENU
BACK
PAR-21MAA
OCH535
37
MONITOR/SET
ON/OFF
ON/OFF
FILTER
DAY
CLOCK
CHECK TEST
OPERATION
CLEAR
Buttons to enter the up/down
operation mode (Press them
simultaneously for 2 seconds.)
■ Up/down operation with the individual specified air-conditioner (when used in combination with Mr. SLIM model)
* Raise or lower the air intake grille of the specific air-conditioner that you select from all that are managed by that remote controller.
1) Ensure that the air-conditioner is not running.
Ensure that the air-conditioner is not running.
Warning:
* The up/down operation mode is only available when the
• Otherwise, it may cause an injury or a failure.
air-conditioner is "OFF".
2) Press both the "FILTER" and "Ventilation" buttons simultaneously for 2 seconds or more to enter the up/down
operation mode.
Up/down operation mode
3) Press the "Ventilation" button. After a while, it will switch to the "individually-specified up/down operation
mode".
Up/down operation mode
Individually-specified up/down operation mode
Refrigerant address No.
Unit No.
If the number of the target airconditioner is unknown, go to 4).
In the upper right figure, the air-conditioner
for which the refrigerant address is "00"
and the unit No. is "1" is currently
selected.
If the number of the target airconditioner is known, go to 5).
4) If you press the "FILTER" button when the "Unit No." or "Refrigerant address No." is blinking, after a while,
the up/down airflow direction of the displayed air-conditioner will be switched downward; and the airflow
direction of the other vents will all be blocked.
■ In Step 5) described below, identify the target
[Remarks:]
■ If "Err" is displayed when you press the "FILTER" button to check the target
air-conditioner by changing the "Unit No." and
air-conditioner, the air-conditioner with that "Unit No." or "Refrigerant
"Refrigerant address No." and by pressing the "FILTER"
address" may not exist. Check and set that air-conditioner again.
button to check the up/down airflow direction.
5) Select the "Unit No." and "Refrigerant address No.".
■ "Unit No." and "Refrigerant address No." can be changed by using the "TEMP." buttons ( ) ( ) when the panel
displays (a) or (b).
■ Every time you press the "Mode selection" button, the target of operation will change as illustrated below.
(a) "Unit No." selection
display
(c) "Standby for up/down operation" display
[Remarks:]
■ Each pressing action changes the unit No. from "1 - 4" to "0".
(Unit No. "0" means that all of 1 - 4 are targeted.)
■ Each press changes the "Refrigerant address" from "0 to 15".
(b) "Refrigerant address No." selection display
6) Continue to press the "Mode selection" button until "Waiting for up/down operation" is displayed.
"Waiting for up/down operation" display
The following steps are the same as steps 3) - 6) described in the "General Operation" section. Refer to that
section.
Operation status display
Down/Up buttons (for selecting
unit No. and refrigerant
address)
Mode selection
Button to exit the up/down
operation mode
TEMP.
MENU
BACK
PAR-21MAA
OCH535
MONITOR/SET
ON/OFF
ON/OFF
FILTER
DAY
CLOCK
CHECK TEST
OPERATION
38
CLEAR
Buttons to enter the up/down
operation mode (Hold them
down simultaneously for 2
seconds.)
10-2. OPERATION (AUTO DESCENDING PANEL: PLP-6BAJ)
(1) Normal operation
UP/DOWN
Wire 1b
Air intake grille is raised/lowered by
UP/DOWN
UP/DOWN
commands of UP and DOWN.
Machine 2
Machine 1
Air intake grille does not move under the
state of no-load detection or obstacle detection.
Air intake grille stops automatically at the set lowering
distance from the ceiling level.
Detection
STOP
Wire 2b
switch
Wire 2a
It stops in the cases below :
• When it reaches at the set lowering distance from
the ceiling level.
It automatically stops after a predetermined period
Wire 1a
of lowering.
Fig.1
• When it is stored in the panel.
The air intake grille is judged to be stored in the panel
when the storage detection switch is pressed for 3 seconds continuously.
• When receiving commands of STOP, DOWN while moving up or UP while moving down.
The STOP button is only available on the automatic filter elevation panel remote controller.
When the wired remote controller is used, there will be a slight delay in stopping due to transmission speed.
• When both wire 1b and 2b are not loaded.
Only the wire b in each UP/DOWN Machine has a tension detection switch.
(2) Special operation
Storage operation
Case : Obstruction of the raising grille before storage or malfunction of storage detection switch
Storage operation will be performed when the intake grille has been raised the set distance but the
storage detection switch is not engaged.
In this case, the operation below will be repeated up to 4 times.
10 cm down 30 cm up
···· 10 cm down 30 cm up
No-load detection
Case : UP/DOWN commands with no grille suspended.
When both wire 1b and wire 2b are not loaded, the wires will not move.
Obstacle detection
Case : Making contact with something while lowering.
Should the loads on the wire 1b and wire 2b be removed due to the grille making contact with something while lowering,
the lowering operation will stop. The grille will then be raised 10 cm and stop again.
[Emergency operation]
• When the wireless remote controller cannot be used (in the case of battery discharge, misplacing of the wireless
remote controller, malfunctioning and so on), the emergency switch on the receiver can be used as an alternative.
* When doing this, particular caution must be taken not to fall.
To lower the air intake grille : Press the
button once.
(For emergency heating operation, press and hold this button.)
To raise the air intake grille : Press the
button once.
(For emergency cooling operation, press and hold this button.)
• To stop the air intake grille from moving, use the opposite buttons to those used to initiate movement.
(To stop it from lowering, press the UP button; To stop it from rising, press the Down button.)
• If up/down machine is out of order, fix air intake grille temporarily and the indoor unit can be operated.
* For details, refer to installation manual for the attachment of grille.
OCH535
39
10-3. ELECTRICAL CIRCUIT (Controller board and wiring diagram (Panel))
10-3-1. Dip SW 22 type
SW22
LS1
BLK
BLK
UK1
LS21
2
1
WHT
WHT
Panel
B O Y
R R L
N N W
CN3G
1 2
W.B
BZ
SW1
MU1
FUSE
CN2F
(BLK)
RU
CN2E
(RED)
2 WHT
1 WHT
CN2C
CN2B
(WHT)
(WHT)
1 2
MU1
ON
SW2
1 2
1 2
LS21
SW22
1 2 3 4 5 6 7 8 9 10
CNB
(WHT)
3 2 1
(BLK)
CN2G
(BLK)
UK1
Indoor unit
3
B R
L E
K D
9
I.B
CN90
(WHT)
CNAC
(WHT)
CN22
(BLU)
CN3G
(BLK)
GRN/YLW
R R B
E E L
1 2
1
2
3
4
5
6
7
8
9
CN3A D D K
B R
L E
K D
(RED)
5 3 1
TB5
Symbol
U.B
Name
Auto grille controller board
Fuse (3.15A)
SW22
Switch (Lowering distance set up)
Up/down machine
Motor (Up/down)
Limit switch (tension detection)
UK1
MU1
LS21
I.B
SYMBOL
FUSE
SW1
SW2
SW3
BZ
RU
SW1
SW2
LS1
R.B
TB6
1
2
R.B
Name
Wireless remote controller board
Buzzer
Receiver
Emergency switch (heating/down)
Emergency switch (cooling/up)
Limit switch (storage detection)
Wired remote controller
Indoor controller board
10-3-2. Dip SW 2 type
U.B
Symbol
W.B
FUSE
1
2
U.B
SW2
NAME
CONTROLLER BOARD
FUSE (T3.15AL250V)
SWITCH (MODEL SELECTION)
SWITCH (LOWERING DISTANCE)
SWITCH (SYSTEM SELECTION)
LED1
LED RED
(MICROCOMPUTER POWER)
LED2
LED RED
(GRILLE CONDITION)
OCH535
I.B
W.B
SYMBOL
BZ
RU
SW1
SW2
NAME
SYMBOL
INDOOR UNIT CONTROLLER BOARD UK1
M
WIRELESS SIGNAL RECEIVER BOARD
LS21
BUZZER
LS1
RECEIVING UNIT
R.B.
EMERGENCY HEATING
GRILLE / DOWN
LONG PRESS FOR OVER 2 SEC) (SHORT PRESS)
EMERGENCY COOLING
GRILLE / UP
LONG PRESS FOR OVER 2 SEC) (SHORT PRESS)
40
NAME
UP/DOWN MACHINE
MOTOR (FOR GRILLE UP/DOWN)
LIMIT SWITCH (TENSION DETECTION)
LIMIT SWITCH (STORAGE DETECTION)
WIRED REMOTE CONTROLLER
10-3-3. Check point of trouble
<LED (SW22 type) /LED2 (SW2 type) display>
Turn OFF
: No power supply
Blink
: Storage detection switch ON (short)
One blink
: Storage detection switch OFF (open)
Two blinks
: Tension detection switch OFF (open)
<controller board>
Check item
Up/down controller
P.C. board supply
voltage
Up/down machine
supply voltage
Check point
Normal
Remarks
CN3A
(between 3-5)
AC 198~264 V
CN2B, CN2C
DC 10~12 V
Check when instructing up/down with LED
blinking once.
Check point
Normal
Check contents
CN2E
open or short
Check if it is short when pressing push switch.
<Up/down machine>
Check item
Storage detection
switch
Tension detection
switch
Motor
CN2F, CN2G
open or short
Check if it is short when wire b is tensioned.
CN2B, CN2C
Check if it is not open or short.
Entwining wires
Pull wire
5~20 Retention:
about 2 kgf
Check if wire is drawn out by pulling with 3 kgf.
10-4. TROUBLESHOOTING
• Check the following points.
Problem
Possible Reason
Corrective Action
Air-conditioner is running.
Stop running the air-conditioner and try again.
Power failure
After recovering from power failure, try again.
Batteries are not inserted into the wireless remote controller.
Or battery power is running low.
Insert or replace the battery.
There is something on the air intake grille.
Or something is stuck in the air intake grille.
Remove the objects or obstacles from the
air intake grille.
Or, remove the stuck object.
There is something on the air intake grille.
Remove the objects or obstacles from the
air intake grille.
Filter is not properly installed.
Lower the air intake grille again and check
whether the filter is installed in the correct
position.
Air intake grille is not hung with all 4 hooks.
Lower the air intake grille again and hook
on the air intake grille.
Air intake grille stops lowering.
(Air intake grille would not
lower any further.)
The air intake grille has finished lowering to the auto-stop
position.
This is normal.
Noises are made during
up/down operation.
(While air intake grille is
moving up/down.)
This is the noise made when the wire is wound and
unwound.
Noises are made while putting
the air intake grille into place.
This is the operational noise for putting the air intake
grille into place.
Air intake grille repeats rising
and lowering several times
while being put into place.
This is the operation for putting the air intake grille into
place.
Air intake grille leans toward
one side during the up/down
operation.
The speeds of winding/unwinding wires are slightly
different for each wire.
Air intake grille does not
function with operation of the
wireless remote controller.
Air intake grille cannot be
fixed in place.
OCH535
41
This is normal.
10-5. ROTATION FUNCTION (AND BACK-UP FUNCTION, 2ND STAGE CUT-IN FUNCTION)
10-5-1. Operation
(1) Rotation function (and Back-up function)
• Outline of functions
· Main and sub unit operate alternately according to the interval of rotation setting.
* Main and sub unit should be set by refrigerant address. (Outdoor Dip switch setting)
Refrigerant address "00"
Main unit
Refrigerant address "01"
Sub unit
· When error occurs to one unit, another unit will start operation. (Back-up function)
• System constraint
· This function is available only by the grouping control system (INDOOR UNIT : OUTDOOR UNIT=1:1) of 2 refrigerant
groups. (Refer to Fig. 1)
· Main indoor unit should be connected for wired remote controller and the transmission line (TB5) for main and sub unit
should also be connected. (Refer to Fig. 1)
(This function cannot be set by wireless remote controller.)
· Set refrigerant address of each unit. (Dip switch on the outdoor unit ··· Refrigerant address 00/01)
Fig. 1
Operation pattern
[Back-up function only]··· Request code number "312"
Error occurs on main unit.
Main
Sub
Start operation
Main
unit
IC-1
Sub
unit
IC-2
Refrigerant address
"00"
Run
Abnormal condition
Stop
Run
3(2)
2
Start operation
Sub
unit
IC-2
3(2)
Main
Sub
Main
Error occurs on main unit.
Sub Main
Sub
Run
Stop
Run
Stop
Run
Stop
1~28 days
Abnormal condition
Sub
unit
IC-2
IC-1
[Rotation function] & [Back-up function]··· Request code number "313~318"
Main
unit
IC-1
OC-2
OC-1
Main
unit
Refrigerant address
"01"
2
RC
OC : Outdoor unit
IC : Indoor unit
RC : Wired remote controller
Run
1~28 days
(Ex:When the request code number is "313", each unit operates alternately in daily cycle.)
Note:
· When the unit is restarted to operate after turning off the power or OFF operation, the unit which was operating will start
operation.
· To operate the main unit, refer to the 10-5-2. and set the request code No. which is not the same as the current one, and set
again the former request code No.
(2) 2nd stage cut-in function
Outline of functions
· When the 1st unit can NOT supply with sufficient capacity for exceptionally high-demand conditions and the actual room
temperature reaches set point *, the 2nd unit starts operation in conjunction with the 1st unit.
· Once the actual room temperature goes down to 4 degrees C below set point *, the 2nd unit stops operation automatically.
(* set point = set temperature by R/C (remote controller) + 4, 6, 8°C (selectable) )
· Number of operating units is determined according to the room temperature and set point.
· When room temperature becomes higher than set point, standby unit starts. (2 units operation)
· When room temperature falls below set point -4°C, standby unit stops. (1 unit operation)
OCH535
42
• System constraint
· This function is available only in cooling mode.
Ex.) Set temp. by R/C = 20:
Set point = 26:
When request code number is “323”.
26:
2nd unit Cut-in
4 degree C
22:
2nd unit Cut-out
[2nd stage cut-in function]··· Request code number "322~324"
Start operation
Main
unit
IC-1
Room temp. Set point
Sub unit start operation
Run
Sub
unit
IC-2
Stop
Run
20:
10-5-2. How to set rotation function (Back-up function, 2nd stage cut-in function)
You can set these functions by wired remote controller. (Maintenance monitor)
NOTICE
Both main and sub unit should be set in same setting.
Every time replacing indoor controller board for servicing, the function should be set again.
(1) Request Code List
Rotation setting
Setting No.
(Request code)
No.1
(310)
No.2
(311)
No.3
(312)
No.4
(313)
No.5
(314)
No.6
(315)
No.7
(316)
No.8
(317)
No.9
(318)
Initial
setting
Setting contents
Monitoring the request code of current setting.
Rotation and Back-up OFF (Normal group control operation)
Back-up function only
Rotation ON (Alternating interval = 1day) and back-up function
Rotation ON (Alternating interval = 3days) and back-up function
Rotation ON (Alternating interval = 5days) and back-up function
Rotation ON (Alternating interval = 7days) and back-up function
Rotation ON (Alternating interval = 14days) and back-up function
Rotation ON (Alternating interval = 28days) and back-up function
2nd unit cut-in setting
Setting No.
(Request code)
No.1
(320)
No.2
(321)
No.3
(322)
No.4
(323)
No.5
(324)
OCH535
Room temp. < Set point -4
Sub unit stop
Initial
setting
Setting contents
Monitoring the request code of current setting.
Cut-in function OFF
Cut-in function ON(Set point = Set temp.+ 4°C (7.2°F)
Cut-in function ON(Set point = Set temp.+ 6°C (10.8°F)
Cut-in function ON(Set point = Set temp.+ 8°C (14.4°F)
43
Stop
(3) Rotation and back up operation
PAR-30MAA/PAR-31MAA
Main
Main menu
Maintenance
Initial setting
Service
Main display:
Cursor
F1
F2
3/3
1 Press the
button.
2 Select "Service" with the [Cursor] buttons ( F1 and F2 ) or the [Page] buttons ( F3
and F4 ), and press the
button.
Page
F3
F4
Service menu
Enter maintenance password
9999
Select:
Cursor
Service menu
1/2
Test run
Input maintenance info.
Function setting
Check
Self check
Main menu:
Cursor
Check menu
1/1
Error history
Refrigerant volume check
Refrigerant leak check
Smooth maintenance
Request code
Service menu:
Cursor
Request code
Ref.address
0
Request code 004
Request:
Cursor
3 Enter the current maintenance password (4 numerical digits).
• Move cursor to the digit you wat to change with the F1 or F2 button.
• Set each number (0 through 9) with the F3 or F4 button.
(Note: The initial maintenance password is "9999".)
4 Then, press the
5 Select "Check" with the F1 or F2 button, and press the
• Rotation & Back up operation: Please match request code with 311 - 318 either.
• 2nd stage cut-in operation: Please match request code with 321 - 324 either.
Press
the
button. Data will be collected and displayed.
0
1 Press the F3 or F4 button to set the Refrigerant address "1".
Please set above 9 - 0.
button.
2 To return to the Main menu, press the
1 To stop air conditioner, press the ON/OFF button.
2 Press the TEST button for three seconds so that "Maintenance
A
D
B
B Refrigerant address
C Data display area
D Request code display area
OCH535
button.
7 Set the Refrigerant address and Request code.
• Select the item to be changed with the F1 or F2 button.
• Select the required setting with the F3 or F4 button.
8 Press the F3 or F4 button to set the Refrigerant address "0".
9 Press the F3 or F4 button to set the desired request code No.
C
button.
6 Select "Request code" with the F1 or F2 button, and press the
PAR-21MAA
button.
mode" appears on the screen (at A ).
"00" (Refrigerant address) appears on the screen in a few minutes (at B ).
3 Press the CHECK button for three seconds to switch to [Maintenance
monitor].
"−−−" appears on the screen (at D ) when [Maintenance monitor] is
activated.
and
) to set the desired
4 Press the [CLOCK] buttons (
request code No.
Rotation & Back up operation: Please match request code with 311 318 either.
2nd stage cut-in operation: Please match request code with 321 - 324 either.
5 Press the FILTER button to perform data request.
(The requested data will be displayed at C in the same way as in
maintenance mode.)
and
) to set the Refrigerant
6 Press the [TEMP] buttons (
address 01.
"01" (Refrigerant address) appears on the screen in a few minutes (at B ).
Please set above 3 - 5.
7 To return to normal mode, press the ON/OFF button.
44
11
DISASSEMBLY PROCEDURE
PLA-ZRP35BA.UK
PLA-ZRP71BA.UK
PLA-ZRP50BA.UK
PLA-ZRP125BA.UK
PLA-ZRP60BA.UK
PLA-ZRP140BA.UK
Be careful when removing heavy parts.
OPERATING PROCEDURE
PHOTOS & ILLUSTRATIONS
1. Removing the air intake grille
(1) Slide the knob of air intake grille toward the arrow 1 to
open the air intake grille.
(2) Remove drop prevention hook from the panel.
(3) Slide the shaft in the hinge to the direction of the arrow 2
and remove the air intake grille.
2. Removing the room temperature thermistor (TH1)
(1) Remove the air intake grille and the filter. (See Figure 1)
(2) Remove the 2 screws from the electrical box.
(3) Disconnect the connector CN20 (Red) from the indoor controller board.
(4) Remove the room temperature thermistor and holder.
Figure 1
Filter
Photo 1
Reactor cover
Fixing
screw
(reactor)
3. Removing the reactor (DCL)
(1) Remove the air intake grille and the filter. (See Figure 1)
(2) Remove the 2 screws from the reactor cover.
(3) Disconnect the relay connector of reactor.
(4) Remove 2 reactor fixing screws and remove the reactor.
4. Removing the indoor controller board (I.B)
(1) Remove the air intake grille and the filter. (See Figure 1)
(2) Remove the 2 screws from the electrical box cover.
(3) Disconnect the connectors :
CNMF (White/7P) for fan motor
CN44 (White/4P) for thermistor (TH2/TH5)
CNP (Blue/3P) for drain pump
CN4F (White/4P) for float switch
CN01 (Black/5P) for earth and reactor
CNV (White/20P) for vane motor
(4) Remove the 6 supports from indoor controller board.
(5) Remove the indoor controller board.
5. Removing the electrical box
(1) Remove the air intake grille and the filter. (See Figure 1)
(2) Remove the 2 screws from the electrical box cover.
(3) Disconnect the connectors. (Refer to 4.)
(4) Remove 2 electrical box fixing screws and remove 2 hooks.
(5) Pull the electrical box.
<Electrical parts in the electrical box>
Indoor controller board
Terminal block (TB4)(TB5)
OCH535
45
Electrical box cover
Fixing screw
(Electrical box)
Photo 2
Bell mouth
Electrical box
Fixing screw
Electrical box
Room temp.
thermistor (TH1)
Turbo fan
Indoor controller
board (I.B)
Electrical box
Fixing screw
OPERATING PROCEDURE
PHOTOS & ILLUSTRATIONS
Coil plate
Photo 3
6. Removing the fan and fan motor (MF)
(1) Remove the electrical box. (See Photo 2)
(2) Remove the bell mouth (3 screws). (See Photo 2)
(3) Remove the turbo fan nut.
(4) Pull out the turbo fan.
(5) Remove the wire cover (3 screws).
(6) Remove 2 wiring clamps.
(7) Disconnect the connector of the fan motor (CNMF).
(8) Remove the 3 nuts and washers and rubber mounts of the
fan motor.
Fan motor
Clamp
Wire cover
fixing screw
Nut
Washer
Rubber mount
Figure 2
7. Removing the panel
(1) Remove the air intake grille and the filter. (See Figure 1)
(2) Disconnect the connector CNV (White/20P).
Corner panel (See Figure 2)
(3) Remove the corner screw.
(4) Slide the corner panel to the direction of the arrow 1, and
remove the corner panel.
Panel (See Photo 4, 5)
(5) Remove the 2 screws from the panel which fix to the oval
holes.
(6) Rotate the panel a little to come to the bell shaped hole
where the screw is large and remove the panel.
Screw
Detail Screw Corner panel
Corner panel
Photo 4
Ball shaped hole
Panel
Photo 5
Oval hole
Photo 6
8. Removing the drain pan
(1) Remove the air intake grille and the filter. (See Figure 1)
(2) Remove the 2 screws from the electrical box cover.
(3) Disconnect the connectors. (Refer to 4.)
(4) Remove the panel. (See Photo 4, 5)
(5) Remove the electrical wiring service panel (3 screws).
(6) Remove the electrical box. (See Photo 2)
(7) Remove the bell mouth. (See Photo 2)
(8) Remove the 4 screws and pull out the drain pan.
w Pull out the left and right of the pan gradually.
Be careful not to crack or damage the pan.
Drain pan
fixing screw
Drain pan
fixing screw
Electrical wiring
service panel
Drain pan
fixing screw
Electrical wiring service panel fixing screw
9. Removing the pipe temperature thermistor (TH2)
and condenser evaporator temperature thermistor (TH5)
(1) Remove the drain pan. (See Photo 6)
(2) Remove the turbo fan. (See Photo 3)
(3) Remove the 2 wiring clamps. (See Photo 3)
(4) Remove the coil plate (2 screws).
(5) Remove the thermistors which are inserted into the holders
installed to the thin copper pipe.
(6) Disconnect the 4-pin white connector (CN44).
Photo 7
Drain pan
Liquid pipe temp. thermistor (TH2)
Cond./ eva. thermistor (TH5)
OCH535
46
OPERATING PROCEDURE
PHOTOS & ILLUSTRATIONS
10. Removing the drain pump (DP) and float switch (FS)
(1) Remove the drain pan. (See Photo 6)
(2) Cut the hose band and remove the hose.
(3) Remove the drain pump assembly (3 screws and 2 hooks).
(4) Remove the drain pump (3 screws).
(5) Remove the float switch (2 screws).
Photo 8
Float switch
Hose band
Drain pump
Drain pump
assembly fixing screw
Photo 9
Drain pump fixing screw
11. Removing the heat exchanger
(1) Remove the drain pan. (See Photo 6)
(2) Remove the 3 screws of the piping cover, and pull out
piping cover.
(3) Remove the 2 screws of coil plate.
(4) Remove the 2 screws of the coil.
(5) Remove the screw of the coil support.
(6) Pull out the heat exchanger.
Photo 10
Piping cover
Coil plate
Heat exchanger
fixing screw
OCH535
47
Float switch fixing screw
Heat exchanger
Coil support fixing screw
Coil support
TM
HEAD OFFICE : TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
CCopyright 2012 MITSUBISHI ELECTRIC CORPORATION
Distributed in Nov. 2012 No.OCH535
Made in Japan
New publication, effective Nov. 2012
Specifications are subject to change without notice.