Samsung 5.2 3D Component Home Entertainment System E5500 User Manual

HW-E5500
AV Receiver System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Safety Information
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous
CAUTION : TO PREVENT ELECTRIC
voltage” inside the product that presents SHOCK, MATCH WIDE BLADE OF PLUG
a risk of electric shock or personal injury. TO WIDE SLOT, FULLY INSERT.
WARNING
~ To reduce the risk of fire or electric shock, do
not expose this appliance to rain or moisture.
CAUTION
~ Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
~ The Mains plug is used as a disconnect device and shall
stay readily operable at any time.
~ This apparatus shall always be connected to an AC outlet
with a protective grounding connection.
~ To disconnect the apparatus from the mains, the plug
must be pulled out from the mains socket, therefore the
mains plug shall be readily operable.
English
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1 PRODUCTO
This symbol indicates important
instructions accompanying the
product.
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein
may result in hazardous radiation exposure.
CAUTION
~ INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.
Precautions
~ Ensure that the AC power supply in your house complies with the identification sticker located on the back of
your product.
~ Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation
(7.5~10cm).
~ Do not place the product on amplifiers or other equipment which may become hot.
Make sure the ventilation slots are not covered.
~ Do not stack anything on top of the product.
~ In order to disconnect the product completely from the power supply, remove the AC plug from the wall outlet,
especially when left unused for a long period of time.
~ During thunderstorms, disconnect the AC plug from the wall outlet. Voltage peaks due to lightning could damage
the product.
~ Do not expose the product to direct sunlight or other heat sources. This could lead to overheating and
malfunction of the product.
~ Protect the product from moisture, and excess heat or equipment creating strong magnetic or electric fields (i.e.
speakers.).
~ Disconnect the power cable from the AC supply if the product malfunctions.
~ Your product is not intended for industrial use. Use of this product is for personal use only.
~ Condensation may occur if your product has been stored in cold temperatures. If transporting the product during
the winter, wait approximately 2 hours until the product has reached room temperature before using.
~ The batteries used with this product contain chemicals that are harmful to the environment.
Do not dispose of batteries in the general household trash.
English
Contents
Safety Information
Safety Warnings
Precautions
Getting Started
6
6
7
7
8
9
10
Key features of your new AV Receiver
Accessories
Description
Front Panel
Display
Rear Panel
Remote Control
CONNECTIONS
13
14
15
16
17
18
19
19
20
Speaker Positioning
Connecting the Speakers
Connecting External Devices/your TV via HDMI
HDMI Function
Connecting to your TV
Connecting a DVD or BD(Blu-ray) Player
Connecting the FM Antenna
Connecting AUX Components
Connecting the USB
Setup
21
21
22
23
23
23
24
24
24
24
25
25
26
26
26
26
27
27
27
27
27
27
Before Using the AV Receiver
Home Menu
Selecting Digital/HDMI/Analog
Setting the Setup menu
Display
TV Aspect
BD Wise (Samsung products only)
Resolution
HDMI Format
Video Out Signal
Audio
Speaker Setting
DRC (Dynamic Range Compression)
Audio Sync
HDMI Audio
User EQ
Audio Return Ch.
System
DivX(R) Registration
DivX(R) Deactivation
Language
Support
2
6
13
21
English
ENGLISH
2
3
Contents
Operation
28
28
28
28
29
29
29
30
30
30
31
31
31
32
32
32
32
33
34
Using the Sound Modes
3D SOUND
DSP (Digital Signal Processor)/EQ
Dolby Pro Logic II Mode
Other Settings
P.BASS
S/W LEVEL
Audio USB (MP3/WMA) Playback
JPEG File Playback
Rotate Function
Listening to the Radio
To Listen in Mono/Stereo
Presetting Radio Stations
Convenient Functions
Sleep Timer Function
Mute Function
Adjust the Display
Reset Function
Software Upgrade
Miscellaneous
35
36
Operating your TV with the Remote Control
Operating your DVD or BD Player with the Remote
Control
Other Information
37
38
38
39
Troubleshooting
Product Protection Function
Licence
Specifications
28
ENGLISH
35
37
•
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product
appearance.
English
Getting Started
Key features of your new AV Receiver
Product Features
3D SOUND
You can enjoy more natural and vivid surround sound with enriched tones.
Digital AV Receiver
This product is a pure digital AV receiver that performs digital signal processing to minimize signal
distortion and loss.
Dolby Digital
Effective audio encoding/decoding technology that provides a vivid surround sound in up to 5.1 channels.
Dolby Pro Logic ll
DPL II processes any high quality stereo signal source into five separate full frequency channels.
DTS (Digital Theater Systems)
DTS provides a discrete 5.1 CH digital audio signal for both music and movie contents and uses less
compression than Dolby Digital for richer sound.
Anynet+ (HDMI-CEC) Function
Anynet+ is a function that can be used to operate this AV Receiver with a Samsung TV remote control,
by connecting the receiver to a SAMSUNG TV using an HDMI Cable. (This function is available only in
connection with Samsung TV and DVD player supporting Anynet+(HDMI-CEC).)
Accessories
Check the box for the supplied accessories listed below.
INPUT SELECT
TV SOURCE
POWER
INPUT SELECT
TV SOURCE
POWER
AVR
TV
AVR
TV
1
1
4
4
7
7
BD
DVD
BD
2
2
5
5
8
8
0
DVD
3
3
6
6
9
9
DSP/EQ
DSP/EQ
0
MUTE
MUTE
VOL
TUNING
/ CH
REPEAT
VOL
DISC MENU
REPEAT
MENU
DISC MENU
MENU
TUNING
/ CH
TITLE MENU
TITLE MENU
TOOLS
INFO
TOOLS
INFO
RETURN
RETURN
EXIT
A
B
C
DIMMER
SLEEP
TUNER
MEMORY
A
3D SOUND
DIMMER
AH59-02382A
3D SOUND
B
C
EXIT
D
MO/ST
D
AUDIO
ASSIGN
P.BASS
SLEEP
S/WTUNER
LEVEL
MEMORY
MO/ST
P.BASS
S/W LEVEL
AUDIO
ASSIGN
AH59-02382A
Remote Control/ Batteries (AAA size)
FM antenna
HDMI Cable
User’s manual
English
Video Cable
01
Getting Started
Description
Front Panel
1
2
3
4
5
6
7 8 9 10
13
11
14
1
POWER BUTTON (
2
INPUT SELECT CONTROL
3
4
5
6
Used to select a source.
FM ; DVD ; AUX ; TV ; USB
AUDIO ASSIGN CONTROL
Toggles to select an input mode for the selected source.
STOP/PLAY BUTTON
Play, pause or stop playing the music in the USB connection.
3D SOUND BUTTON
Press to apply 3D Sound effect.
DISPLAY
Displays the speaker/audio input status, listening mode, etc.
7
8
9
10
11
12
13
DSP/EQ BUTTON
Select the desired DSP/EQ audio mode.
DIMMER BUTTON
Adjust the brightness of Display.
TUNING MODE BUTTON
Used to select the Manual or Preset mode for FM radio.
MEMORY BUTTON
Used to set a preset radio frequency.
TUNING CONTROL
Used to change the radio frequency.
MASTER VOLUME CONTROL
Adjusts the volume level.
14
AUX IN JACKS
USB PORT
)
12
Turns the receiver on/off.
Connect the USB storage device to play a multimedia file of video, photo, and
music.
Auxiliary AV input terminals used to connect a camcorder, portable DVD player or
gaming device.
English
Getting Started
Display
1
2
4
3
5
1
2
SPEAKER INDICATORS
Displays sound producing speakers.
SPEAKER LEVEL INDICATOR
Displays the speaker level.
3
AUDIO INPUT INDICATORS
Displays the audio input signal type of the currently connected external audio
source.
4
MESSAGE DISPLAY
Informs you of the status of the receiver.
5
RADIO FREQUENCY
INDICATORS
Displays the current radio frequency range.
English
01
Getting Started
Rear Panel
1
2
3
4 5
1
2
3
4
5
6
7
8
9
SPEAKERS OUT TERMINALS
Speaker connection terminals.
ONLY FOR SERVICE JACK
Used for the service repair.
10
6
7
8
9
10
OPTICAL IN JACKS (DIGITAL AUDIO IN) Receives the digital optical audio signal. (BD/DVD, TV)
COAXIAL IN JACK (DIGITAL AUDIO IN)
Receives the digital coaxial audio signal. (AUX)
VIDEO OUT JACK
Outputs the video signal to a monitors (TV, Projector etc).
AUDIO IN JACKS
Receives the audio signal from a video player (BD/DVD, TV).
VIDEO IN JACKS
Receives the video signal from a video player (BD/DVD, TV).
FM ANTENNA JACK
Connect the FM antenna.
HDMI OUT JACKS
Outputs digital video and audio signals simultaneously using an HDMI cable.
HDMI IN JACKS
Receives digital video and audio signals simultaneously using an HDMI
cable.
English
Getting Started
Remote Control
Tour of the Remote Control
1
INPUT SELECT
TV SOURCE
POWER
21
2
3
4
AVR
TV
BD
DVD
BD
DVD
1
2
3
4
5
6
4
5
6
7
8
9
7
8
0
23
24
7
25
8
VOL
10
DISC MENU
9
DSP/EQ
0
MUTE
9
MUTE
TUNING
/ CH
REPEAT
MENU
TITLE MENU
26
27
VOL
TUNING
/ CH
REPEAT
MENU
DISC MENU
TITLE MENU
28
11
TOOLS
INFO
29
TOOLS
INFO
RETURN
EXIT
30
13
14
15
16
17
18
19
TV
3
6
12
AVR
2
5
English
22
1
DSP/EQ
10
20
INPUT SELECT
TV SOURCE
POWER
RETURN
EXIT
A
B
C
D
DIMMER
SLEEP
TUNER
MEMORY
MO/ST
3D SOUND
P.BASS
S/W LEVEL
AUDIO
ASSIGN
AH59-02382A
31
32
33
34
35
A
B
C
D
DIMMER
SLEEP
TUNER
MEMORY
MO/ST
3D SOUND
P.BASS
S/W LEVEL
AUDIO
ASSIGN
AH59-02382A
01
POWER button
Turns the receiver on/off.
2
TV button
To change to TV mode, press the TV button.
3
AVR button
To change to AVR(AV Receiver) mode, press the AVR button.
4
NUMBER buttonS
Used to select a TV channel.
5
DOLBY PRO LOGIC II button
Select the desired Dolby Pro Logic II audio mode.
6
SKIP buttonS
Press to skip backwards or forwards on a connected DVD/BD player.
7
STOP/PLAY button
Press to stop/start playback on a connected DVD/BD player.
8
MUTE button
Mutes the sound of a connected device.
9
VOLUME CONTROL buttonS
Adjusts the volume of the selected device.
10
MENU button
Press to move to the home menu.
11
DISC MENU button
Press to view the disc menu.
12
TOOLS button
Press to use the Tools menu.
13
UP/DOWN/LEFT/RIGHT buttonS
Used to navigate the menus.
14
RETURN button
Used to return to the previous menu from the SETUP menu.
15
FUNCTION BUTTONS
Allow access to common functions of the product.
16
SLEEP button
Used to set the Sleep Timer.
17
DIMMER button
Adjusts the brightness of the display.
18
3D SOUND BUTTON
Press to apply 3D Sound effect.
19
P.BASS button
Select the desired Power Bass Enhancement setting.
20
INPUT SELECT,
TV SOURCE button
Toggles to find and select an input source.
Press to select a connected TV's video source.
21
BD button
To change to BD mode, press the BD button.
22
DVD button
To change to DVD mode, press the DVD button.
23
DSP/EQ button
DSP/EQ modes have been designed to simulate different acoustic
environments.
24
SEARCH button
Press to search backwards or forwards.
25
PAUSE button
Pauses playback on a connected device.
26
TUNING/CHANNEL buttonS
Used to change the radio broadcasting frequency or TV channel.
English
Getting Started
1
11
Getting Started
27
REPEAT button
Allows you to repeat a title, chapter, track or disc.
28
TITLE MENU button
Use to enter the title menu.
29
INFO button
Display information on the connected device currently being used.
30
ENTER button
Used to select an item in the SETUP menu.
31
EXIT button
Exits the SETUP menu.
32
TUNER MEMORY BUTTON
Used to set a preset radio frequency.
33
MO/ST BUTTON
Select MONO or STEREO for radio broadcasts.
34
AUDIO ASSIGN BUTTON
Toggles to select an input mode for the selected source.
35
S/W LEVEL button
Used to adjust the level of the subwoofer.
Installing batteries in the Remote Control
Follow these precautions to avoid leaking or cracking cells:
` Place batteries in the remote control so they
`
`
`
`
match the polarity : (+) to (+) and (–) to (–).
Assuming typical AVR usage, the batteries last for
about one year.
Use the correct type of batteries. Batteries that
look similar may differ in voltage.
Always replace both batteries at the same time.
Do not expose the batteries to heat or a flame.
* Battery size: AAA
Operation Range of the Remote Control
The remote control can be used up to approximately 23 feet/
7 meters in a straight line. It can also be operated at a
horizontal angle of up to 30° from the remote control sensor.
INPUT SELECT
TV SOURCE
POWER
AVR
TV
BD
1
2
4
5
7
8
DVD
3
6
9
DSP/EQ
0
MUTE
VOL
TUNING
/ CH
REPEAT
DISC MENU
MENU
TITLE MENU
TOOLS
INFO
RETURN
B
C
D
SLEEP
TUNER
MEMORY
MO/ST
3D SOUND
P.BASS
S/W LEVEL
AUDIO
ASSIGN
AH59-02382A
12
English
EXIT
A
DIMMER
02
Connections
Speaker Positioning
* Speakers are provided with model HW-E5500 only.
6.6~9.8 feet (2~3m)
AV RECEIVER
SL
SR
Position of AV Receiver
Place the AV Receiver on a dedicated stand or rack.
Subwoofer g
The position of the subwoofer is not so critical. Place it anywhere you like.
Front Speakers
Place these speakers in front of your listening position, facing inwards (about 45°) toward you.
Place the speakers so that
tweeters will be at the same height as your ears.SBL
SBL their SBR
SBR
Align the front face of the front speakers with the front face of the center speaker or place them slightly in
front of the center speaker.
Center Speaker
It is best to install it at the same height as the front speakers.
You can also install it directly over or under the TV.
Surround Speakers
SBL
SBR
SBL
SBR
SBL
SBR
Place these speakers behind your listening position.
If there isn't enough room, place these speakers so they face each other.
Unlike the front and center speakers, the surround speakers are used to handle mainly sound effects and
sound will not come from them all the time.
✎ NOTE
` If you place a speaker near your TV set, screen color may be distorted because of the magnetic field
generated by the speaker. If this occurs, place the speaker away from your TV set.
English
1
Connections
This section involves various methods of connecting the AV receiver to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connections
Connecting the Speakers
Connecting Speaker Wire
1. Loosen the knob by turning counterclockwise.
2. Insert the bare part of the wire into the hole in the side of each
terminal.
3. Tighten the knob by turning clockwise to secure the wire.
Connecting the Speakers
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into the red
terminal (+), and then release the tab.
3. Connect the speaker wire plugs to the back of the product by matching
the Colors of the speaker plugs to the speaker jacks.
Black
Red
CENTER SURROUND (L) SUBWOOFER SUBWOOFER
Model HW-E5500
AV Receiver
FRONT SPEAKER
CENTER SPEAKER
SURROUND SPEAKER
SUBWOOFER
HW-E5500
PS-FE5500
PS-CE5500
PS-SE5500
PS-WE5500
FRONT (R) FRONT (L) SURROUND (R)
✎ NOTE
` Speakers are provided with model HW-E5500 only.
` Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or
objects into the duct (hole).
` Never touch speaker terminals while the power is on. Doing so could result in electric shock.
` Make sure the polarities (+ and -) are correct.
1
English
02
HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray
player, set-top box and more.
HDMI removes any loss of signal from analog conversion, enabling you to enjoy video and audio sound
quality as it was originally created in the digital source.
By connecting through the HDMI (High-Definition Multimedia Interface) interface, you can play back digital
video and audio.
DVD or
AUX (Set-top box,
Blu-ray Player Game Console)
• Connect it if you want to use
Anynet+. (If connected TV support
ARC, it is not necessary to connect
the OPTICAL OUT.)
OPTICAL
OUT
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both the connected external device and TV must
support High-bandwidth Digital Content Protection System (HDCP). This product supports HDCP.
Compatibility with a TV Supporting HDmI
A TV with an HDMI jack.
Video/Audio
A TV with a DVI-D jack (TV supporting HDCP)
Video
A TV with a DVI-D jack (TV not supporting HDCP)
-
✎ NOTE
` Audio from SACD discs will not be heard with this connection. To play a DVD disc whose copyright is protected
by CPPM, use a player supporting CPPM.
` The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the
performance of the connected device.
` Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.
English
1
Connections
Connecting External Devices/your TV via HDmI
Connections
HDMI Function
Using Anynet+ (HDMI-CEC)
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's
remote control. Anynet + can be used by connecting this AV Receiver to a SAMSUNG TV using an
HDMI Cable. This is only available with SAMSUNG TVs and SAMSUNG AV Products that support
Anynet+.
1. Connect the AV receiver to a Samsung TV with an HDMI cable. (See page 15)
2. Set the Anynet+ function on your TV.
(See the TV instructions manual for more information.)
• You can operate the volume on the AV receiver by using Volume buttons on the TV remote
control.
✎ NOTE
` If you use an HDMI cable to connect a Samsung TV to your AV Receiver, you can operate the AV
receiver using the TV’s remote control. This function is available only in connection with Samsung
TV and DVD player supporting Anynet + (HDMI-CEC).
` Please check your TV for the ANYNET+ logo. If your TV has an ANYNET+ logo, then it supports
the Anynet+ function.
` When you are making Anynet+ connection, do not connect more than two AV receivers (Anynet+
installed). Otherwise, it can cause a malfunction.
16
English
02
Connections
Connecting to your TV
or
VIDEO
IN
OPTICAL
OUT
AUDIO
OUT
Video Connection
Connect the Video cable (supplied) from the VIDEO OUT jack on the back of your AV Receiver to the Video
Input jack on your TV.
Audio Connection
Connect the Digital Input (OPTICAL (TV)) on your AV Receiver to the Digital Output of the TV.
OR
Connect AUDIO IN (TV) on your AV Receiver to the Audio Out of the TV.
English
1
Connections
Connecting a DVD or BD(Blu-ray) Player
VIDEO
IN
or
OPTICAL
OUT
COAXIAL
OUT
or
AUDIO
OUT
VIDEO
OUT
DVD or BD Player
or
Video Connection
Connect a Video cable (supplied) from the VIDEO IN (BD/DVD) jack on the back of your AV Receiver to the Video
Output jack on your DVD/BD player.
Audio Connection
Connect the Digital Input (OPTICAL (BD/DVD)) on your AV Receiver to the Digital Output of the DVD/BD player.
OR
Connect the Digital Input (COAXIAL (AUX)) on your AV Receiver to the Digital Output of the BD/DVD player.
OR
Connect AUDIO IN (BD/DVD) on your AV Receiver to the Audio Out of the DVD/BD player.
✎ NOTE
` Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
` If the cable/set-top box has only one audio output jack, connect it to either the right or left audio input jack of
the main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
1
English
02
1. Connect the FM antenna supplied to the FM ANTENNA terminal as a temporary measure.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall
or other rigid surface.
FM antenna (supplied)
✎ NOTE
` Do not place the antenna cable close to the power cord. Keep it as far away as possible.
` If you experience poor FM reception, use an external antenna.
Connecting AUX Components
You can connect external devices you use for a short time (camcorder, game console, mobile equipment,
etc.) to the front of this unit for convenience.
Camcorder
VIDEO
OUT
AUDIO
OUT
English
1
Connections
Connecting the Fm Antenna
Connections
Connecting the USB
You can use the USB connection to play multimedia files (MP3, JPEG, DivX, etc) downloaded from the USB
storage device.
1. In Stop mode, connect the USB storage device to the USB port on the front panel of the product.
2. Use the front USB PLAY ►, or STOP @ on the front panel to play, pause or stop playing the music.
USB
Notes on USB connection
Supported devices: USB storage media, MP3 player, digital camera
1) If a folder or file name is longer than 10 characters, it may not properly display or operate.
2) A subtitle file bigger than 300KB may not be properly displayed.
3) A certain USB/digital camera device, USB card reader is not supported.
4) FAT16 and FAT32 file systems are supported.
5) Photo (JPEG), music (MP3, WMA) and video file should have their names in English or Korean.
Otherwise, the file may not played.
6) Connect directly to the product's USB port. Connecting through another cable may raise problems with
USB compatibility.
7) Inserting more than one memory device to a multi-card reader may not operate properly.
8) PTP protocol for digital camera is not supported.
9) Do not disconnect USB device during a "Reading" process.
10) Bigger the image resolution, the longer the delay to displaying.
11) DRM applied MP3/WMA or video files downloaded from a commercial site are not played back.
12) External HDD device is not supported.
13) The maximum current supported by the USB port for an external device is 500 mA (at 5V DC).
14) Supported file formats
Format
Still
Picture
File name
JPG
File
extension
JPG
.JPEG
Bitrate
20
Music
Movie
WMA
WMV
DivX
.MP3
.WMA
.WMV
.AVI
–
80~320
kbps
56~128
kbps
4Mbps
4Mbps
Version
–
–
V8
V1,V2,
V3,V7
Pixel
640x480
–
–
English
MP3
DivX3.11~
DivX5.1,
XviD
720x480
03
Setup
Setup
For your convenience, you can set this AV receiver's features for the best use.
Before Using the AV Receiver
Turning On/Off
Connect the power plug to the outlet.
This unit will set to Standby mode.
Press the POWER button on the main unit.
• This unit will be turned on.
• You can also turn the unit on/off by pressing the POWER button on the remote control.
Remote Control Functions
You can operate your AMP (this AV receiver)/ TV and BD(Samsung only)/DVD player with this remote
control. See pages 35 ~ 36 for more details.
To Select a Function
Press the INPUT SELECT button on the remote control.
• Each time you press this button, FM ➡ DVD ➡ AUX ➡ TV ➡ USB will be selected in turn.
Home Menu
Press the MENU button to return to USB FUNCTION from any other functions. Then, you will see the
Home Menu screen.
✎ NOTE
` For using the OSD menus, refer to Setting the setup
menu.
Settings
` The OSD (On Screen Display) may change in this
product after you upgrade the software version.
Function
USB
Remove USB
English
21
VOL
DISC MENU
Setup
Selecting Digital/HDmI/Analog
You can listen to sound of analog, HDMI, optical input using this unit.
1. Press the INPUT SELECT button on the remote control to select a
desired function (DVD, AUX, TV). See page 10.
2. Press the AUDIO ASSIGN button on the remote control to select the
audio input source of the external device you have connected.
• Each time you press this button, the input mode changes as
follows:
TUNING
/ CH
REPEAT
MENU
TITLE MENU
TOOLS
INFO
RETURN
EXIT
A
B
C
D
DIMMER
SLEEP
TUNER
MEMORY
MO/ST
3D SOUND
P.BASS
S/W LEVEL
AUDIO
ASSIGN
AH59-02382A
~ For BD/DVD function






~ For AUX function
~ For TV function
~ For USB function
✎ NOTE
` You can also change the input mode by turning the AUDIO ASSIGN button on the front of your
AV Receiver.
` You can enjoy Dolby Digital or DTS if you connect the digital audio output jack of an external
audio component to the optical or coaxial digital audio input jack on the main unit.
` For the TV function, the TV ARC menu will be displayed only if an ARC-compliant TV is
connected.
English
4
5
7
8
6
9
DSP/EQ
0
03
Setup
Setting the Setup menu
MUTE
The access step may
differ depending
on the selected menu. The GUI (Graphical User Interface) in this
TUNING
VOL
/ CH
REPEAT
manual may differ, depending
on
the firmware version.
1
DISC MENU
MENU
TITLE MENU
TOOLS
INFO
3
RETURN
2
EXIT
A
B
C
D
DIMMER
SLEEP
TUNER
MEMORY
MO/ST
1. Press the POWER
button.
P.BASS S/W LEVEL
3D SOUND
1
mENU BUTTON : Display the home menu.
2
RETURN BUTTON : Return to the previous
setup menu.
3
ENTER / DIRECTION BUTTON
Move the cursor and select an item.
Select the currently selected item.
Confirm the setting.
4
EXIT BUTTON : Exit the setup menu.
4
AUDIO
ASSIGN
Settings
2. Press the mENU button on the remote control.
AH59-02382A
3. Press the _+ buttons to select Settings, then press the
ENTER button.
4. Press the $% buttons to select the desired menu, then
press the ENTER button.
5. Press the $% buttons to select the desired sub-menu,
then press the ENTER button.
Function
Remove USB
USB
6. Press the $% buttons to select the desired item, then press the ENTER button.
7. Press the EXIT button to exit the setup menu.
Display
TV Aspect (USB Playback only)
Depending on the type of television you have, you may want to adjust the screen setting.
~ 4:3 Pan-Scan
~ 4:3 Letter Box
~ 16:9 Wide
Select when you connect the product
to a 4:3 TV screen. 16:9 content will
have the extreme left and right portions
cut off.
Select when you connect the product
to a 4:3 TV screen. The product will
display all content in its original aspect
ratio. Content formatted in 16:9 will be
displayed with black bars on the top
and bottom.
Select when you connect the product
to a 16:9 TV screen. All content will fill
the full screen. Content formatted in
4:3 will be stretched.
English
Setup
✎ NOTE
` When using HDMI, the screen is automatically converted to the 16:9 Wide mode and TV Aspect
is deactivated.
` If a file is in the 4:3 ratio, you cannot view it in the wide screen.
` Since file are recorded in various image formats, they will look different depending on the
software, the type of TV, and the TV aspect ratio setting.
BD Wise (Samsung products only)
BD Wise is Samsung's latest inter-connectivity feature. When you connect Samsung products with
BD-Wise to each other via HDMI, the optimum resolution will be set automatically.
~ On : The original resolution of the DVD disc will be output to the TV direct.
~ Off : The output resolution will be fixed according to the Resolution previously set, regardless of the
resolution of the disc.
✎ NOTE
` For HDMI connection, the BD Wise setting of the source device will prevail over the setting of the
main unit.
` This will optimize the picture quality according to the content (In the DVD disc, etc) that you want
to play and the product or your BD Wise-compliant Samsung TV.
` If you want to change the resolution in BD Wise mode, you must set BD mode to Off in advance.
` BD Wise will be disabled if the product is connected to a device that does not support BD Wise.
Resolution
Sets the output resolution of the HDMI video signal.
The number in 576p(480p), 720p, 1080i and 1080p indicates the number of lines of video.
The i and p indicate interlace and progressive scan, respectively.
~
~
~
~
~
576p(480p) : Outputs 576(480) lines of progressive video.
720p : Outputs 720 lines of progressive video.
1080i : Outputs 1080 lines of interlaced video.
1080p : Outputs 1080 lines of progressive video.
BD Wise : Automatically sets the optimal resolution when connected via HDMI to a TV with the BD
Wise feature. (The BD Wise menu item appears only if BD Wise is set to On.)
✎ NOTE
` If Composite is connected, the resolution supports only 576i(480i).
` 1080P may not appear depending on TV.
HDMI Format
You can optimize the Color setting from the HDMI output. Select a connected device Type.
~ Monitor : Select if connected to a Monitor via HDMI.
~ TV : Select if connected to a TV via HDMI.
Video Out Signal
Different countries apply different TV standard. You can select from NTSC or PAL.
~ NTSC : You can select the NTSC video format
~ PAL : You can select the PAL video format
24
English
03
Setup
Audio
Speaker Setting
Speaker Size
You can set the Speaker Size of the Center and Surround Speakers, as well as Test Tone in this mode.
~ For the Front, the mode is set to Small.
~ For the Subwoofer, the mode is set to Present.
~ For the Center and Surround, you can switch the mode to
Small or None.
- Small : Select this when using the speakers.
- None : Select this when no speaker is connected.
Settings
Speaker Setting
Speaker Size
▶
Sound Edit
Delay Time
Test Tone
: Off
✎ NOTE
" Select
` The speaker mode may vary depending on the
' Return
" Select
mMove
' Return
Dolby Pro Logic and Stereo settings.
Sound Edit
You can adjust the balance and level for each speaker.
Press the $% buttons to select and adjust the desired
speaker.
Press the _+ buttons to adjust the settings.
Adjusting Front/Surround Bal.
` You can select between 0 and -6.
` The volume decreases as you move closer to –6.
Settings
Sound Edit
Front Bal.
dB L
R
dB
Surround Bal.
dB L
R
dB
Center Level
dB
Surround Level
dB
SW Level
dB
<Change " Select
mMove
' Return
" Select
' Return
Adjusting Center/Surround/Subwoofer Level
` The volume level can be adjusted in steps from +6dB to –6dB.
` The sound gets louder as you move closer to +6dB and quieter as you get closer to -6dB.
Delay Time
If the speakers cannot be placed at equal distances from
the listening position, you can adjust the delay time of the
audio signals for Surround speakers.
You can also set the Test Tone in this mode.
Settings
Setting up the Speaker Delay Time
When 5.1CH Surround Sound is played, you can enjoy the
best sound if the distance between you and each speaker is
the same.
Since the sounds arrive at the listening position at different
times depending on the placement of speakers, you can adjust
this difference by adding a delay effect to the Center and Surround Speakers.
Delay Time
Front
Center : 00ms
Surround : 00ms
Subwoofer
Test Tone
: Off
<Change " Select
mMove
' Return
" Select
' Return
English
25
Setup
✎ NOTE
` You can not set Center and Surround in this mode when their Speaker Size is set to NONE.
Test Tone
Use the Test Tone feature to check the speaker
connections.
Settings
Speaker Setting
Speaker Size
~ Press the _+ buttons to select On.
~ The test tone will be sent to Front Left ➞ Center ➞
Front Right ➞ Surround Right ➞ Surround Left ➞
Subwoofer in order.
To stop the test tone, press the ENTER button.
Sound Edit
Delay Time
Test Tone
mmove
: On
▶
" Select
' Return
" Select
' Return
DRC (Dynamic Range Compression)
This feature balances the range between the loudest and quietest sounds. You can use this function to
enjoy Dolby Digital sound when watching movies at low volume at night.
~ You can select either Full, 6/8, 4/8, 2/8, off.
Audio Sync
Video and audio sync may not match with digital TV. If this occurs, adjust the audio delay time to
match the video
~ You can set the audio delay time between 0 ms and 300 ms. Set it to the optimal status.
HDmI Audio
The audio signals transmitted over the HDMI Cable can be toggled On/Off.
~ Off : Video is transmitted over the HDMI connection cable only, and audio is output through the
product speakers only.
~ On : Both video and audio signals are transmitted over the HDMI connection cable, and audio is
output through your TV speakers only.
✎ NOTE
`
`
`
`
`
The default setting of this function is HDMI Audio Off.
HDMI Audio is automatically down-mixed to 2ch for TV speakers.
When HDMI Audio is set to On, PL II/DSP EQ/P.BASS/3D SOUND doesn't work.
With HDMI AUDIO set to 'On', the volume can be adjusted only using the TV remote control.
If you select a different function, HDMI AUDIO will be deactivated accordingly.
User EQ
You can configure the equalizer settings manually to your
preference.
Settings
User EQ
dB
6
·
·
·
·
·
·
·
·
·
·
·
·
-6
250Hz
600Hz
1kHz
3kHz
6kHz
10kHz 15kHz
a Reset > Adjust < Move ' Return
mmove
English
" Select
' Return
03
Setup
Audio Return Ch.
You can enjoy TV sound from the Home Cinema speakers by using just one HDMI cable.
~ Off : Turn the Audio Return Channel function off.
~ Auto : Listen to TV sound through the Home Cinema speakers if your TV is compatible with the Audio
Return Channel function.
✎ NOTE
` When Anynet+ (HDMI-CEC) is Off, the Audio Return Channel function is not available.
` Using an ARC (Audio Return Channel)-uncertified HDMI cable may cause a problem in compatibility.
` ARC function is only available if an ARC-compliant TV is connected.
System
DivX(R) Registration
View DivX(R) VOD Registration Code to purchase and play DivX(R) VOD content.
✎ NOTE
` This option is not activated if you select OK.To activate this option, please activate the DivX(R)
Deactivation.
` Even after you reset the system, the settings of DivX Registration will not be reset.
DivX(R) Deactivation
Select this to get a new registration code.
Language
You can select the language you prefer for on-screen menu, disc menu, etc.
OSD Language
DivX Subtitle
Select the language for the on-screen displays.
Select the language for disc subtitles.
Support
Product Information
Provide the product information such as Model Code, MPEG Version, etc.
English
27
Operation
Using the Sound Modes
3D SOUND
Press the 3D SOUND button.
~ Each time you press this button, 3D SOUND ON  3D SOUND OFF will be selected in turn.
~ You can also select the 3D SOUND mode by pressing the 3D SOUND button on the remote
control.
✎ NOTE
` The 3D sound effect will not be available for FM.
DSP (Digital Signal Processor)/EQ
Press the DSP/EQ button.
~ Each time you press this button, OFF  POPS  JAZZ  ROCK  USER  STUDIO 
CLUB  HALL  MOVIE  CHURCH  GAME  CONCERT  STADIUM  OFF will be
selected in turn.
~ You can also select the DSP/EQ mode by pressing the DSP/EQ button on the remote control.
✎ NOTE
` The menu may vary depending on the region.
` The DSP/EQ function is only available in Stereo mode.
` The DSP/EQ function is not available while playing AC3 signal in 2.1 channel mode.
Dolby Pro Logic II Mode
Press the
PL II button.
~ Each time you press this button, MUSIC  MOVIE  PROLOGIC  MATRIX  STEREO will
be selected in turn.
✎ NOTE
` You cannot use Dolby Pro Logic ll mode for Analog multi channel signals.
` Pro Logic works with the audio signals with sampling frequencies of 32KHz, 44KHz or 48KHz.
` Before selecting Dolby Pro Logic II mode, connect your external device to the AUDIO INPUT jacks
(L and R) on the product. If you connect to only one of the inputs (L or R), you cannot listen to surround
sound.
` The Pro Logic II function is only available in Stereo mode.
` The Pro Logic II function is not available while playing AC3 signal in 2.1 channel mode.
28
English
04
Operation
Other Settings
P.BASS
Press the P.BASS button on the remote control.
~ Each time you press this button, P.BASS ON  P.BASS OFF will be selected in turn.
✎ NOTE
` The P.BASS function provides a bass boost to reinforce the low frequencies.
` The P.BASS function is only available with 2 channel LPCM sources such as MP3, DivX, CD and
WMA.
` The P.BASS function does not work with Dolby Pro Logic ll modes.
` If you press P.BASS in the DSP/EQ mode, the DSP/EQ mode is automatically shut off and the
P. BASS function will be turned on.
S/W LEVEL
You can also press the S/W LEVEL button on the remote control and use the _ or + buttons to
adjust the level of subwoofer.
~ You can set the between -6 and +6. Set it to the optimal status.
English
29
Operation
Audio USB (MP3/WMA) Playback
1. Connect the USB storage device to the USB port on the
front panel of the product.
~ For the MP3/WMA file, press the _+ buttons to select
Music, then press the ENTER button.
- Press the $%_+ buttons to select a desired file
and press the ENTER button.
- Press the () buttons to move to the previous/
next pages.
2. Press the STOP (@) button to stop playback.
Track01
1/17
0:15 / 3:59
Function USB
Repeat Play Mode
✎ NOTE
` Some MP3/WMA file may not play, depending on the recording mode.
` Table of contents of a USB varies depending on the MP3/WMA track format recorded on the disc.
` WMA-DRM files cannot be played.
JPEG File Playback
Images captured with a digital camera or camcorder, or JPEG files on a PC can be stored on a USB
and then played back with this product.
1. Connect the USB storage device to the USB port on
the front panel of the product.
ROOT
JPEG 1
2. Press the _+ buttons to select Photos, and then
press the ENTER button.
JPEG 2
JPEG 3
3. Press the $% buttons to select the folder you want to
play, and then press the ENTER button.
4. Press the ▲▼ buttons to select the photo you want to
play, and then press the ENTER button.
~ The selected file will play and slide show will start.
~ To stop slide show, press the PAUSE (#) button.
~ You can view the previous/next file by pressing the
◀,▶ buttons during the slideshow mode.
642 X 352
Function USB
2011/01/01
Pages
Return
Rotate Function
Press the GREEN(B) or YELLOW(C) button during the PAUSE mode.
~ GREEN (B) Button: Rotate 90° counterclockwise.
~ YELLOW(C) Button: Rotate 90° clockwise.
✎ NOTE
` The maximum resolutions supported by this product are 5120 x 3480 (or 19.0 MPixel) for standard
JPEG files and 2048 x 1536 (or 3.0 MPixel) for progressive image files.
30
English
04
Operation
Listening to the Radio
You can listen to the radio by using either automatic or manual tuning.
1. Press the INPUT SELECT button on the remote control to select FM.
2. If you want to switch the tuning mode between Preset and Manual, use the TUNING MODE
button in the front panel, or the STOP button on the remote control.
~ Each time you press this button, PRESET  MANUAL
3. Select a frequency (radio broadcast).
~ Preset tuning :
Use the TUNING dial on the front panel or press the TUNING/CH ( .,, ) buttons on the
remote control to select a preferred frequency.
~ Manual tuning 1 (Automatic tuning) :
Press and hold the TUNING/CH ( .,, ) buttons on the remote control to automatically tune in
a frequency.
~ Manual tuning 2 :
Press the TUNING/CH ( .,, ) buttons on the remote control to increase or decrease the
frequency step by step.
To Listen in Mono/Stereo
Press the MO/ST button on the remote control.
~ Each time you press this button, STEREO or MONO will be selected in turn.
~ If you select MONO in an area with weak reception, it will help to reduce noise.
~ This function works only with the remote control.
Presetting Radio Stations
You can preset up to 15 FM stations.
E.g.: Setting station FM 89.10 in preset 2.
1. P
ress the INPUT SELECT button on the remote control to select
FM.
2. Press the TUNING/CH ( .,, ) buttons on the remote control to
select 89.10.
~ Refer to step 3 above to tune in automatically and manually.
3. Press the MEMORY button on the main unit.
~ You can also use the TUNER MEMORY button on the
remote control.
~ Tuner number will blink on the display.
4. Press the TUNING/CH ( .,, ) buttons on the remote control to
select preset 2.
~ You can select from presets 1 to 15.
5. Press the MEMORY button on the main unit.
~ Tuner number will disappear and station 89.10 will be saved
in preset 2.
6. To preset other stations, repeat steps 2 to 5.



English
31
MUTE
VOL
Operation
DISC MENU
Convenient Functions
TUNING
/ CH
REPEAT
MENU
TITLE MENU
TOOLS
INFO
RETURN
EXIT
Sleep Timer Function
You can set the time that this unit will shut itself off.
Press the SLEEP button.
~ SLEEP : OFF  SLP 10  SLP 20  SLP 30  SLP 60  SLP 90
 SLP 120  SLP 150 will be selected in turn.
To check sleep timer
A
DIMMER
POWER
3D SOUND
POWER
AH59-02382A
Press the SLEEP button.
~ The remaining time before this unit will shut itself off is shown on the
display.
~ Pressing the button again changes the sleep time from what you set
previously.
To cancle sleep timer
~ Press the SLEEP button until SLEEP OFF appears on the display.
AVR
B
C
SLEEP
TUNER
MEMORY
P.BASS
S/W LEVEL
TV
BD
4
1
7
4
TV
Press the MUTE button again or press the Volume button.
~ mUTE will disappear and sound will output.
Adjust the Display
DVD
6
3
9
6
DSP/EQ
9
0
MUTE
This function is useful when answering a doorbell or telephone call.
To output sound again
3
DSP/EQ
mute Function
Press the MUTE button.
~ mUTE appears on the display.
DVD
BD
5
2
8
5
0
8
7
AUDIO
ASSIGN
INPUT SELECT
TV SOURCE
2
1
AVR
D
INPUT SELECT
MO/ST
TV SOURCE
VOL
TUNING
/ CH
MUTE
REPEAT
REPEAT
TITLE MENU
TUNING
/ CH
MENU
INFO
TITLE MENU
DISC MENU
MENU
VOL
TOOLS
DISC MENU
TOOLS
INFO
RETURN
EXIT
You can adjust the brightness of the display.
Press the DIMMER button.
~ Each time you press this button, the brightness changes as follows :
Dark(Light on)  Bright(Light off)  Dark(Light off)  Bright(Light on).
A
B
C
SLEEP
TUNER
MEMORY
P.BASS
S/W LEVEL
AUDIO
ASSIGN
DIMMER
SLEEP
TUNER
MEMORY
MO/ST
3D SOUND
P.BASS
S/W LEVEL
AUDIO
ASSIGN
RETURN
DIMMER
3D SOUND
A
AH59-02382A
✎ NOTE
` SLEEP, Mute can only be operated with the remote control.
English
AH59-02382A
B
C
D
EXIT
MO/ST
D
04
Operation
Reset Function
When the Power is on,
In "No USB" mode, press and hold the STOP button to
reset the system.
~ INIT appears on the display.
~ The unit will turn off after 5 seconds.
No USB
Settings
✎ NOTE
` Using the RESET function will erase all stored settings.
` Do not use this unless necessary.
Function
USB
English
Operation
Software Upgrade
Samsung may offer upgrades for AV Receiver's firmware in the future.
Please visit Samsung.com or contact the Samsung call center at to receive information about
downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB
drive to the USB port located on your AV Receiver.
1. Insert a USB drive containing the firmware upgrade into
the USB port on the front of the main unit.
2. Select a folder that contains the upgradeable firmware
files. (This applies to all of Video, Photos and Music.)
3. The upgrade process will be performed automatically.
4. The main unit will turn off automatically after completing
the firmware upgrade.
5. Remove the USB drive from the front USB port.
6. Turn the power on, switch to USB mode and wait until
“No USB” appears on the front display.
7. Press the “STOP” button for 5 seconds on the remote
control or the front panel while in “No USB” is displayed.
8. The set automatically powers off, and initialization is finished.
✎ NOTE
` Please be careful not to disconnect the power or remove the USB drive while upgrades are being
applied. When software is upgraded, settings you have made will return to their default (factory)
settings. We recommend you write down your settings so that you can easily reset them after the
upgrade.
` If you failed software upgrade, it is strongly recommended whole USB data format to FAT16 and retry
software upgrade.
` The NTFS USB File System can not be supported.
` Depending on the manufacturer, the USB may not be supported.
English
05
Miscellaneous
1.
2.
3.
4.
Press the POWER button to turn on the TV.
Press the TV button to set the remote to TV mode.
Point the remote control toward the TV.
While holding down the POWER button, enter the code corresponding to your brand of TV.
~ If there is more than one code listed for your TV in the table, enter one at a time to determine
which code works.
~ If the code matches the TV's code, the TV will be turned off.
5. If TV is turned on or off when you press the POWER button of the remote control, the setting is
completed.
~ You can use the TV POWER, VOLUME, CHANNEL, MENU and Numeric buttons (0~9).
✎ NOTE
` The remote control may not work on some brands of TVs. Also, some operations may not be
possible depending on your brand of TV.
` The remote control will work with Samsung TVs by default.
TV Brand Code List
Brand
Code
Brand
Code
Brand
Code
Admiral (m.Wards)
56, 57, 58
Inkel
45
Realistic
03, 19
A mark
01, 15
JC Penny
56, 59, 67, 86
Sampo
40
Anam
01, 02, 03, 04, 05, 06, 07, 08, 09, 10,
11, 12, 13, 14
JVC
70
Samsung
00, 15, 16, 17, 40, 43, 46,
47, 48, 49, 59, 60, 98
AOC
01, 18, 40, 48
Bell & Howell
(m.Wards)
KTV
59, 61, 87, 88
KEC
03, 15, 40
57, 58, 81
KmC
15
Brocsonic
59, 60
LG (Goldstar)
Candle
18
01, 15, 16, 17, 37, 38, 39, 40, 41,
42, 43, 44
Luxman
18
LXI (Sears)
19, 54, 56, 59, 60, 62, 63, 65, 71
magnavox
15, 17, 18, 48, 54, 59, 60, 62, 72, 89
marantz
40, 54
matsui
54
mGA
18, 40
18, 40, 59, 60, 75
Cetronic
03
Citizen
03, 18, 25
Cinema
97
Classic
03
Concerto
18
Contec
46
Sanyo
19, 61, 65
Scott
03, 40, 60, 61
Sears
15, 18, 19
Sharp
15, 57, 64
Signature 2000
(m.Wards)
57, 58
Sony
50, 51, 52, 53, 55
Soundesign
03, 40
Spectricon
01
SSS
18
Sylvania
18, 40, 48, 54, 59, 60, 62
Coronado
15
mitsubishi/
mGA
Symphonic
61, 95, 96
Craig
03, 05, 61, 82, 83, 84
mTC
18
Tatung
06
Croslex
62
NEC
18, 19, 20, 40, 59, 60
Techwood
18
Crown
03
Nikei
03
Teknika
03, 15, 18, 25
Curtis mates
59, 61, 63
Onking
03
TmK
18, 40
CXC
03
Onwa
03
Toshiba
19, 57, 63, 71
Daewoo
02, 03, 04, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24,
25, 26, 27, 28, 29, 30, 32, 34, 35, 36, 48, 59, 90
Panasonic
06, 07, 08, 09, 54, 66, 67, 73, 74
Vidtech
18
Daytron
40
Penney
18
Videch
59, 60, 69
Dynasty
03
Emerson
03, 15, 40, 46, 59, 61, 64, 82, 83, 84, 85
Fisher
19, 65
Funai
03
Futuretech
03
General Electric (GE)
06, 40, 56, 59, 66, 67, 68
Hall mark
40
Hitachi
15, 18, 50, 59, 69
Philco
03, 15, 17, 18, 48, 54, 59, 62, 69, 90
Wards
15, 17, 18, 40, 48, 54, 60, 64
Philips
15, 17, 18, 40, 48, 54, 62, 72
yamaha
18
Pioneer
63, 66, 80, 91
york
40
Portland
15, 18, 59
yupiteru
03
Proton
40
Zenith
58, 79
Quasar
06, 66, 67
Zonda
01
Radio Shack
17, 48, 56, 60, 61, 75
Dongyang
03, 54
RCA/Proscan
18, 59, 67, 76, 77, 78, 92, 93, 94
English
miscellaneous
Operating your TV with the Remote Control
Miscellaneous
Operating your DVD or BD Player with the Remote Control
1. Press the POWER button to turn on the DVD (BD) player.
2. Press the DVD/BD button on the remote control to set the remote to DVD (BD) mode.
3. Point the remote control toward the DVD (BD).
4. While holding down POWER button, enter the code corresponding to your brand of DVD (BD).
~ If there is more than one code listed for your DVD (BD) in the table, enter one at a time to
determine which code works.
~ If the code matches the DVD (BD)'s code, the DVD (BD) will be turned off.
5. If DVD (BD) is turned on or off when you press the POWER button of the remote controller, the
setting is completed.
~ You can use DVD (BD) POWER, PLAY, PAUSE, STOP, SKIP, MENU and Numeric buttons
(0~9).
✎ NOTE
` The remote control may not work on some brands of DVD.
Also, some operations may not be possible depending on your brand of DVD.
` The remote control will work with Samsung DVD (BD) by default.
DVD Brand Code List
Brand
DENON
DOONOON
DMTECH
FISHER
GE
HARMAN/KARDON
JVC
KENWOOD
LG
MAGNAVOX
MITSUBISHI
Code Number
003, 032
019
017
002
006
012
010, 013
008
001
004
005, 016
Brand
Code Number
ONKYO
OPTIMUS
PANASONIC
PROSCAN
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SONY
THETA DIGITAL
004, 014
011
021
006
004, 023
007, 011, 022, 025
006
000, 027
002
015, 020
011
Brand
TOSHIBA
YAMAHA
ZENITH
TAEGWANG
PS2
X-BOX
APEX
Marantz
BD Player Brand Code List
Brand
SAMSUNG
Code Number
000, 001, 002, 003, 004
✎ NOTE
` The remote control will control Samsung BD players only.
36
English
Code Number
004, 018
009, 033
004, 024
026
028
029
030
031
06
Other Information
Other Information
Troubleshooting
Before requesting service, please check the following.
Symptom
Check
Remedy
The unit will not turn on.
• Is the power cord plugged into the
outlet?
• C
onnect the power plug to the
outlet.
A function does not
work when the button is
pressed.
• Is there static electricity in the air?
• Disconnect the power plug and
connect it again.
Sound is not produced.
• A
re the speakers and external
components connected properly?
• Is the Mute function on?
• Is the volume set to minimum?
• Connect them correctly.
• Press the MUTE button to
cancel the function.
• Adjust the volume.
Picture does not appear
on a TV when the
function is selected.
• Is the external component
connected properly?
• Connect it correctly.
Remote controller does
not work.
• Are the batteries drained?
• Is the distance between remote
control and main unit too great?
• Replace with new batteries.
• Operate at close distance.
The sound from the left/
right channels is
reversed.
• A
re the left/right speaker or left/right
input/output cables connected
properly?
• C
heck the left/right channel and
connect it/them correctly.
Can't receive radio
broadcasts.
• Is FM antenna connected
properly?
• Connect the antenna correctly.
• If the input strength of antenna
signal is weak, install the FM
antenna in a place with good
reception.
There is no sound from
surround speakers.
• A
re the surround speakers
connected properly?
• Is SR (surround) incorrectly set to
NONE in the Speaker Size?
• Is surround mode set to stereo?
Can't select Dolby Pro
Logic ll mode.
• Is the input signal selected
properly?
• R
efer to page 14 to connect
them properly.
• Refer to page 25 to select
SMALL or NONE.
• Only 2 channel signal can
select Dolby Pro Logic II mode.
(ex:PCM, 2 channel analog
input signal.)
English
37
Other Information
Product Protection Function
Heat protection
~ The protection function will come on if the main unit or power transformer overheats.
"
" will appear in the display .
This function will come on :
- If speaker terminal is shorted
- If speaker cable is shorted
If there is no problem when you turn the unit on again after turning it off, PROTECT mark will
disappear on the display and the unit will work properly.
Licence
~ HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other
countries.
~ ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary
of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit
www.divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX
VOD section in your device setup menu. Go to vod.divx.com for more information on how to
complete your registration.
DivX Certified® to play DivX® video, including premium content.
DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries.
and are used under license. Covered by one or more of the following U.S. patents : 7,295,673;
7,460,668; 7,515,710; 7,519,274
~ Dolby, Pro Logic, and the double-D symbol are registered trademarks of Dolby
Laboratories.
~ Manufactured under license under U.S. Patent #'s: 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and
the Symbol are registered trademarks & DTS Digital Surround and the DTS logos are
trademarks of DTS, Inc. Product includes software.©DTS, Inc. All Rights Reserved.
38
English
06
Other Information
Specifications
GENERALZ
FM TUNER
AMPLIFIER
FREQUENCY
RESPONSE
HDMI
VIDEO OUTPUT
Weight
5.4 Kg
Dimensions (W x H x D)
429.2 x 165.1 x 360 mm
Operating temperature range
+5°C~+35°C
Operating humidity range
10%~75%
Frequency response
87.5~108.0MHz
Usable sensitivity
12dBf
S/N ratio
MONO/STEREO 60dB/60dB
Distortion
MONO/STEREO 0.3/0.8%
Stereo separation
30dB
Tuner output level
1kHz, 75kHz Dev
Rated output
20Hz~20kHz/THD = 10%
Front speaker (left+right)
4 Ω 150W/CH
Center speaker
4 Ω 150W/CH
Surround speaker (left+right)
4 Ω 150W/CH
Double subwoofer
4 Ω 150W/CH
Input sensitivity/impedance
550mV/47kΩ
S/N ratio (analog input)
65dB
Separation (1kHz)
55dB
Analog input
20Hz~20kHz(±3dB)
Digital input/96kHz PCM
20Hz ~44kHz(±3dB)
Input
Compatible 1080p
Output
Compatible 1080p
TV format
NTSC/PAL
Input level/impedance
1Vp-p/75 Ω
Output level/impedance
1Vp-p/75 Ω
Video frequency response
5Hz to 10kHz(-3dB)
S/N Ratio
60dB
* S/N Ratio, Distortion, Separation and Usable sensitivity are based on measurement using AES (Audio
Engineering Society) guidelines.
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
English
39
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
Area
` North America
Contact Center 
Web Site
Canada
Mexico
U.S.A
1-800-SAMSUNG (726-7864)
01-800-SAMSUNG (726-7864)
1-800-SAMSUNG (726-7864)
www.samsung.com
www.samsung.com
www.samsung.com
Argentine
Brazil
Chile
Colombia
Costa Rica
Dominica
Ecuador
El Salvador
Guatemala
Honduras
Jamaica
Nicaragua
Panama
Peru
Puerto Rico
Trinidad &
Tobago
Venezuela
0800-333-3733
0800-124-421 / 4004-0000
800-SAMSUNG (726-7864)
01-8000112112
0-800-507-7267
1-800-751-2676
1-800-10-7267
800-6225
1-800-299-0013
800-7919267
1-800-234-7267
00-1800-5077267
800-7267
0-800-777-08
1-800-682-3180
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
1-800-SAMSUNG (726-7864)
www.samsung.com
0-800-100-5303
www.samsung.com
Albania
42 27 5755
0810 - SAMSUNG (7267864,
€ 0.07/min)
-
` Latin America
` Europe
Austria
Belgium
02-201-24-18
Bosnia
Bulgaria
Croatia
05 133 1999
07001 33 11
062 SAMSUNG (062 726 7864)
800-SAMSUNG (800-726786)
Samsung Zrt., česká organizační
složka, Oasis Florenc, Sokolovská394/17, 180 00, Praha 8
70 70 19 70
030 - 6227 515
01 48 63 00 00
01805 - SAMSUNG (726-7864
€ 0,14/Min)
06-80-SAMSUNG (726-7864)
800-SAMSUNG (726-7864)
+381 0113216899
261 03 710
023 207 777
020 405 888
0900-SAMSUNG
(0900-7267864) (€ 0,10/Min)
815-56 480
0 801 1SAMSUNG (172678)
/ 022-607-93-33
80820-SAMSUNG (726-7864)
1. 0 8010 SAMSUNG (72678) doar din reţeaua Romtelecom,
tarif local
2. 021.206.01.10 - din orice
reţea, tarif normal
Czech
Denmark
Finland
France
Germany
Hungary
Italia
Kosovo
Luxemburg
Macedonia
Montenegro
Netherlands
Norway
Poland
Portugal
Rumania
www.samsung.com
www.samsung.com/
be (Dutch)
www.samsung.com/
be_fr (French)
www.samsung.com
www.samsung.com
Area
Serbia
Slovakia
Spain
Sweden
Contact Center 
0700 Samsung (0700 726
7864)
0800-SAMSUNG (726-7864)
902-1-SAMSUNG (902 172 678)
0771 726 7864 (SAMSUNG)
Switzerland
0848-SAMSUNG (7267864,
CHF 0.08/min)
U.k
Eire
Lithuania
Latvia
Estonia
0330 SAMSUNG (7267864)
0818 717100
8-800-77777
8000-7267
800-7267
Russia
Georgia
Armenia
Azerbaijan
Uzbekistan
Kyrgyzstan
Tadjikistan
8-800-555-55-55
8-800-555-555
0-800-05-555
088-55-55-555
8-10-800-500-55-500
(GSM: 7799)
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
Ukraine
0-800-502-000
Belarus
Moldova
810-800-500-55-500
00-800-500-55-500
Australia
New Zealand
China
1300 362 603
0800 SAMSUNG (0800 726 786)
400-810-5858 / 010-6475 1880
Hong Kong
(852) 3698 4698
` CIS
Kazakhstan
` Asia Pacific
Web Site
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/ch
www.samsung.com/
ch_fr/(French)
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.ua
www.samsung.com/
ua_ru
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/hk
www.samsung.com/
hk_en/
www.samsung.com
Philippines
www.samsung.com
www.samsung.com
www.samsung.com
-
Singapore
Thailand
Taiwan
Vietnam
3030 8282 / 1800 110011 /
1800 3000 8282 / 1800 266 8282
0800-112-8888 /
021-5699-7777
0120-327-527
1800-88-9999
1-800-10-SAMSUNG(726-7864) /
1-800-3-SAMSUNG(726-7864) /
1-800-8-SAMSUNG(726-7864) /
02-5805777
1800-SAMSUNG (726-7864)
1800-29-3232 / 02-689-3232
0800-329-999
1 800 588 889
Bahrain
Egypt
Jordan
Morocco
Oman
Saudi Arabia
Turkey
U.A.E
8000-4726
08000-726786
800-22273
080 100 2255
800-SAMSUNG (726-7864)
9200-21230
444 77 11
800-SAMSUNG (726-7864)
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
Nigeria
South Africa
0800-SAMSUNG (726-7864)
0860-SAMSUNG (726-7864 )
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
India
Indonesia
Japan
Malaysia
` Middle East
` Africa
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
Code No. AH68-02342K