Samsung AZ09F1TEA User Manual

Window-type Room Air Conditioner ( Cool and Heat )
Acondicionador de aire doméstico sistema de tipo ventana ( Refrigeración y Calefacción )
Climatiseur de type Fenêtre ( Refroidissement et Chauffage )
O ar Condicionado de Window-Type ( Refrigeração e Aquecimento )
Condizionatore d’aria per ambienti da finestra ( Raffreddamento e Riscaldamento )
E S F P I DB68-02007A(3)
ENGLISH
ESPAÑOL
FRANÇAIS
AZ09AASEA
AZ09AAJEA
AZ12AAJEA
AZ18AAMEA
AZ18AAMEB
AZ22AAMEA
AZT18AAMEA
AZT24AAMEA
PORTUGUÊS
AZ09FASEA
AZ09FAJEA
AZ12FAJEA
AZ18FAMEA
AZ18FAMEB
AZ22FAMEA
AZT18FAMEA
AZT24FAMEA
ITALIANO
OWNER’S INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’UTILISATION
MANUAL DE INSTRUÇÕES
ISTRUZIONI PER L'USO
Safety Precautions
The following safety precautions must be taken when installing
and using your air conditioner.
1 The air conditioner must be plugged into its own specific power source, which must be
installed in compliance with national wiring, earthing and safety regulations.
Depending on national regulations and your specific installation, you may need to install:
◆ A circuit breaker
For further information on electrical requirements, contact a professional electrician.
This device must be installed according to the national electrical rules.
2 Make sure that the unit is correctly ventilated at all times;
do NOT place clothing or other materials over it.
3 NEVER spill liquids of any kind into the unit.
Should this happen, unplug the unit and contact your installation specialist.
4 Do NOT insert anything between the air outlet blades, as it may damage the inner fan
and you may be hurt. Keep children away from the unit.
5 ALWAYS ensure that the power cable is in good condition.
If the power cord is damaged in any way, it must be replaced by an authorized service technician.
Do not use an extension cord with this or other appliance.
6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact:
◆ An authorized service center
◆ The dealer from whom you purchased the air conditioner.
7 Do NOT place any blocking objects in front of the unit.
8 If the remote control will not be used for a long time, remove the batteries.
9 Before throwing out the device, it is necessary to pull back the battery cells
and get rid of them safely.
CAUTION
The manufacturer does not assume responsibility for accidents or injury
caused by an incorrectly installed air conditioner. If you are unsure about
installation, contact an installation specialist.
E-2
ENGLISH
Contents
◆ PREPARING YOUR AIR CONDITIONER
■
■
■
■
■
Safety Precautions .........................................................................................
Air Conditioning Unit - Main Parts, Buttons and Display ...............................
Remote Control Buttons .................................................................................
Getting Started ...............................................................................................
Inserting the Remote Control Batteries ..........................................................
2
4
5
6
7
◆ OPERATING YOUR AIR CONDITIONER
■
■
■
■
■
Cooling Your Room ........................................................................................ 8
Heating Your Room ........................................................................................ 9
Airing Your Room ........................................................................................... 10
Adjusting the Air Flow Direction Horizontally .................................................. 11
Adjusting the Air Flow Direction Vertically ...................................................... 11
◆ PROGRAMMING YOUR AIR CONDITIONER
■
■
■
Setting the On Timer ...................................................................................... 12
Setting the Off Timer ...................................................................................... 13
Setting the Sleep Timer .................................................................................. 14
◆ RECOMMENDATIONS FOR USE
■
■
■
■
■
Operating Recommendation ...........................................................................
Temperature and Humidity Ranges ................................................................
Cleaning Your Air Conditioner ........................................................................
Solving Common Problems ............................................................................
Technical Specifications .................................................................................
◆ METHOD
OF INSTALLATION
15
16
17
19
19
.................................................................................... 20
CAUTION
" The high inrush current of the starting compressor motor can have adverse effects to
the operation of other equipment under unfavorable mains conditions. This equipment
does not comply with the relevant technical standards for the limitation of voltage
fluctuations and flicker."
Before connecting this equipment to the power supply system, please report to your
supply authority and obtain the consent.
Do not connect other electric appliances to the same supply lines.
AZ18✴✴
The maximum permissible system impedance at the power junction box is 0.27 ohms.
Usually, the maximum permissible mains impedance will not be exceeded when the
branch to the power outlet is fed from a junction box with a rated current of 32A.
E-3
Air Conditioning Unit - Main Parts, Buttons and Display
❄ The design and shape are subject to
change according to the model.
Inner air flow blades
(right/left orientation)
Air outlet
Air inlet (inside)
Outer air flow blades
(up/down orientation)
Air filter
Air inlet (Outside)
(The air filter is
located inside)
Ventilation lever
Power plug
(The type of the power
plug may differ according
to the type of local power
supply.)
Fan speed indicators
(LOW, MED, HIGH)
Air flow blade swing indicator
Temperature/Timer
settings
Temperature adjustment
buttons
Timer setting button
Sleep timer setting button
Operating mode indicators
(COOL, FAN, HEAT)
Timer indicator
Deice indicator
Remote Control sensor
Air flow blade swing button
Operating mode selection
button(COOL, FAN, HEAT)
Fan speed adjustment
button
ON/OFF button
E-4
ENGLISH
Remote Control - Buttons
Timer setting button
Sleep timer setting button
Operating mode
selection buttons
Air flow blade swing button
Temperature adjustment
buttons
Fan speed adjustment
buttons
ON/OFF button
E-5
Getting Started
You have just purchased a window-type room air conditioner and it has been installed by your
installation specialist.
Your Owner’s Instructions contain valuable information on using your air conditioner.
Please take the time to read them as they will help you take full advantage of the unit’s functions.
This Owner’s Instructions is just for using your air conditioner correctly.
Thus, the illustrations shown in this manual may not exactly match your air conditioners.
The booklet is organized as follows.
◆ The following figures are shown on pages 4 and 5:
-
Air conditioning unit (main parts, buttons and display)
-
Remote control (buttons)
They will help you find the buttons and understand the symbols displayed.
◆ In the main part of the document, you will find a series of step-by-step procedures for each
function available.
The illustrations in the step-by-step procedures use four different symbols:
PRESS
PUSH
☛
➢
IMPORTANT
NOTE
Moreover, applicable, wherever the illustrations show the positions of the buttons on both the
remote control and the unit itself.
E-6
For the...
The illustrations have a...
Remote control
Gray background.
Example:
Unit itself
White background.
Example:
ENGLISH
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when:
◆ You purchase the air conditioner
◆ The remote control does not work correctly
☛
Use two AAA, LR03 1.5 V batteries. Do not use old
batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months,
even if they have not actually been used.
1
Push the battery cover on the rear of the remote control with your thumb in
the direction of the arrow and remove it.
2
Insert the two batteries, taking care to respect the polarities:
◆ + on the battery with + on the remote control
◆ – on the battery with – on the remote control
3
Close the cover by sliding it back until it clicks into place.
Result:
You can control all the functions on your air conditioning unit
directly from your seat, using the remote control.
E-7
Cooling Your Room
Remote Control
Control Panel
You must select the Cool mode if you wish to lower the temperature in your
room. You can also set the fan speed.
1
If necessary, press the
(On/Off) button.
◆ The operating mode indicator (COOL, FAN or HEAT) on
Result:
the unit comes on.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The unit beeps twice.
air conditioner is fitted with a protection mechanism to prevent
☛ The
the unit from being damaged when it is started immediately after
being:
◆ Plugged in
◆ Stopped
It will start up automatically after about three minutes.
2
If the COOL indicator is not lit up on the unit:
◆ Press the
button on the remote control
or
◆ Press the MODE button on the unit one or more times until the COOL
indicator lights up
◆ The unit beeps each time you press MODE.
Result:
◆ The air conditioner starts up in Cool mode.
➢
3
You can change modes at any time.
To adjust the temperature, press the
or
button on the remote
control one or more times until the required temperature is displayed.
To adjust the temperature, press the
or
button on the unit one
or more times until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
◆ Each time you press the temperature buttons:
Result:
– The temperature is adjusted by 1°C and
displayed on the control panel
– The unit beeps
◆ The air conditioner starts cooling if the room temperature is
higher than the selected temperature.
4
To set the fan speed to...
Then...
High
◆ Press the
button on the remote control.
or
◆ Press the
on the unit until the
indicator lights up
Med
◆ Press the
button on the remote control.
or
◆ Press the
on the unit until the
indicator lights up
Low
◆ Press the
button on the remote control.
or
◆ Press the
on the unit until the
indicator lights up
Result:
5
E-8
Each time you press a button, the unit beeps.
To control the direction of the air flow, refer to page 11.
You must select the Heat mode if you wish to heat your room to a specific
temperature. You can also set the fan speed.
1
ENGLISH
Heating Your Room
Remote Control
Control Panel
If necessary, press the
(On/Off) button.
◆ The operating mode indicator (COOL, FAN or HEAT) on
Result:
the unit comes on.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The unit beeps twice.
air conditioner is fitted with a protection mechanism to prevent
☛ The
the unit from being damaged when it is started immediately after
being:
◆ Plugged in
◆ Stopped
It will start up automatically after about three minutes.
2
If the HEAT indicator is not lit up on the unit:
◆ Press the
button on the remote control
or
◆ Press the MODE button on the unit one or more times until the HEAT
indicator lights up
◆ The unit beeps each time you press MODE.
Result:
◆ The air conditioner starts up in Heat mode.
➢
3
You can change modes at any time.
To adjust the temperature, press the
or
button on the remote
control one or more times until the required temperature is displayed.
To adjust the temperature, press the
or
button on the unit one
or more times until the required temperature is displayed.
Possible temperatures are between 16°C and 30°C inclusive.
◆ Each time you press the temperature buttons:
Result:
– The temperature is adjusted by 1°C and
displayed on the control panel
– The unit beeps
◆ The air conditioner starts heating if the room temperature is
lower than the selected temperature.
4
To set the fan speed to...
Then...
High
◆ Press the
button on the remote control.
or
◆ Press the
on the unit until the
indicator lights up
Med
◆ Press the
button on the remote control.
or
◆ Press the
on the unit until the
indicator lights up
Low
◆ Press the
button on the remote control.
or
◆ Press the
on the unit until the
indicator lights up
Result:
5
Each time you press a button, the unit beeps.
To control the direction of the air flow, refer to page 11.
E-9
Airing Your Room
If the atmosphere in your room is stale, you can air it using the Fan
feature and if necessary, evacuate the stale air outside.
1
If you wish to evacuate stale air outside, push the ventilation lever on the front
of the unit to the right and the open position (
).
Result:
The air inside the room circulates and stale air is evacuated outside.
Otherwise, push the ventilation lever to the left and the closed position (
The air simply circulates inside the room.
Result:
Remote Control
Control Panel
2
If necessary, press the
(On/Off) button.
◆ The operating mode indicator (COOL, FAN or HEAT) on the
Result:
unit comes on.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The unit beeps twice.
3
If the FAN indicator is not lit up on the unit:
◆ Press the
button on the remote control
or
◆ Press the MODE button on the unit one or more times until the FAN
indicator lights up
Result:
➢
4
◆
◆
5
◆ The unit beeps each time you press MODE.
◆ The air conditioner starts up in Fan mode.
You can change modes at any time.
When the air conditioner is in Fan mode, the
temperature is not displayed; in this case, you do not
need to set the temperature.
To set the fan speed to...
Then...
High
◆ Press the
button on the remote control.
or
◆ Press the
on the unit until the
indicator lights up
Med
◆ Press the
button on the remote control.
or
◆ Press the
on the unit until the
indicator lights up
Low
◆ Press the
button on the remote control.
or
◆ Press the
on the unit until the
indicator lights up
Result:
E-10
).
Each time you press a button, the unit beeps.
To control the direction of the air flow, refer to page 11.
ENGLISH
Adjusting the Air Flow Direction Horizontally
Depending on the position of the unit in your room, you can adjust the
orientation of the inner air flow blades on the right-hand side of the
unit, thus increasing the efficiency of the air conditioner.
1
Press the
Result:
➢
2
(or
Control Panel
on the unit) button on the remote control.
The inner blades swing automatically left and right.
The blades may stop swinging momentarily when the Deice function is
activated (see page 15 for further details on this function.) They will start
swinging again automatically as soon as the Deice function stops.
To stop the blades moving left and right, press the
button on the remote control.
➢
Remote Control
(or
on the unit)
To stop the blades in a specific position and orient the air flow in the
corresponding direction, simply press the
(or
on the unit)
button on the remote control when the blades are in the desired position.
Adjusting the Air Flow Direction Vertically
Again depending on the position of the unit in your room, you can
adjust the orientation of the outer air flow blades on the right-hand
side of the unit.
RECOMMENDATION
When...
Adjust the blades to face...
Cooling
Upwards.
Heating
Downwards.
Adjust the air flow blades to the desired position, by pushing them upwards or
downwards.
➢
If you orient the air flow blades downwards and the unit operates in Cool mode
for a long period of time, dew may:
◆ Form on the surface of the blades
◆ Drip from the blades
E-11
Setting the On timer
Remote Control
Control Panel
The On Timer enables you to switch on the air conditioner automatically after
a given period time. You can set the period of time from 1 hour to 24 hours.
You can set the period of time from 1 hour to 24 hours.
You can select the On timer only when the air conditioner is off.
1
Check that the air conditioner has been switched off; if necessary,
press the
(On/Off) button.
2
Set the required mode by pressing the appropriate button:
◆
,
or
on the remote control
◆ Mode button on the unit (press it one or more times until the
appropriate operating mode indicator lights up)
3
Set the operating time by pressing:
◆ Timer on the remote control.
or
◆ Timer on the unit one or more times.
Possible time is between 1 hour and 24 hour inclusive.
Result:
➢
◆ The remaining time is displayed and decreased by 1 hour
automatically to indicate the remaining time.
◆ The air conditioner switches on automatically when the
operating time reaches zero.
You can change the setting mode, fan speed, and air flow direction
after setting the On timer.
To Cancel the On Timer
To cancel the On timer, press:
◆ Timer on the remote control or unit one or more times until "
" is
displayed.
or
◆
on the remote control or unit (The air conditioner operates in the mode
selected when the unit was last used.)
E-12
ENGLISH
Setting the Off Timer
The Off Timer enables you to switch off the air conditioner
automatically after a given period of time.
You can set the period of time from 1 hour to 24 hours.
You can select the Off timer only when the air conditioner is on.
1
Check that the air conditioner has been switched on; if necessary,
press the
(On/Off) button.
2
Set the operating time by pressing:
◆ Timer on the remote control
or
◆ Timer on the unit one or more times.
Remote Control
Control Panel
Possible times are between 1 hour and 24 hour inclusive.
Result:
➢
◆ The remaining time is displayed and decreased by 1 hour
automatically to indicate the remaining time.
◆ The air conditioner switches off automatically when the
operating time reaches zero.
You can change the setting mode, fan speed, and air flow direction
after setting the Off timer.
To Cancel the Off Timer
To cancel the Off timer, press:
◆ Timer on the remote control or unit one or more times until "
" is
displayed.
or
◆
on the remote control or unit (The air conditioner operates in the mode
selected when the unit was last used.)
E-13
Setting the Sleep timer
The Sleep Timer can be used when you are cooling or heating your
room to switch the air conditioner off automatically after a period of
8 hours.
Remote Control
Control Panel
➢
If you wish to switch the unit off at a specific time, refer to page 13.
1
Make sure that you have selected either COOL or HEAT mode.
2
Press the
or
Press the
Result:
Cooling
button on the remote control
button on the unit until the SLEEP indicator lights up.
◆ Each time you press a button, the unit beeps.
◆ The “SLEEP” passes through the control panel for about
15 seconds and the "
" will be displayed.
◆ The remaining time is displayed and decreased by 1 hour
automatically to indicate the remaining time.
◆ The air conditioner will be controlled as illustrations below.
When the temperature has
been increased by 1°C (after
1 hour), it is maintained for 7
hours.
Set
TEMP.
1hr
Start
time
Heating
The temperature is decreased
by 1°C after 1 hour.
When it has been decreased
by 2°C (after 2 hour), the
temperature is maintained for
6 hours.
To Cancel the Sleep Timer
To cancel the timer, press:
◆
on the remote control.
or
◆
on the unit.
Result:
E-14
◆ The unit beeps.
◆ The SLEEP indicator is no longer displayed.
◆ The air conditioner operates in the mode selected last.
8hr
Stop
time
ENGLISH
Operating Recommendations
Here are a few recommendations that you should follow when using your air conditioner.
Topic
Recommendation
Heating performances
The heat pump inside the air conditioner absorbs heat from outside air
and brings it indoors. If the temperature of the outside air drops, the air
conditioner will heat less. If you find that the room is not warm enough,
use an additional heating appliance.
Warm air circulation
The air conditioner circulates warm air to heat your room; as a result,
some time will be required after starting the air conditioner to warm the
entire room. If necessary, set the air conditioner going a short time
before you wish to use the room.
Frost
When outside temperatures are low and humidity is high, frost may
form in the unit’s condensor when heating with your air conditioner. If
this happens:
◆ The unit stops heating
◆ The air flow blades stop swinging
◆ The Deice mode is triggered automatically for about five minutes
◆ The DEICE indicator on the unit lights up red
No intervention is required from you; after about five minutes, the air
conditioner starts operating again normally.
High indoor and outdoor
temperatures
If both the indoor and outdoor temperatures are high and you select
the Heat mode, the fan and compressor in the unit may stop at times.
This is normal; simply wait until the air conditioner switches on again.
E-15
Temperature and Humidity Ranges
The following table indicates the temperature and humidity ranges within which the air
conditioner can be used.
E-16
Mode
Indoor Temperature
Outdoor Temperature
Indoor Humidity
Cooling
Heating
21°C to 32°C approx.
28°C or less
21°C to 43°C approx.
0°C to 21°C approx.
80% or less
-
If the air conditioner is used at...
Then...
Higher temperatures
The automatic protection feature may be triggered and the air
conditioner stopped.
Lower temperatures
A water leakage or some other malfunction may happen if the
heat exchanger freezes.
Higher humidity levels
Water may condense on and drip from the surface of the unit if
it is used for long periods.
ENGLISH
Cleaning Your Air Conditioner (✴✴✴✴FA✴✴✴ models)
Be sure to clean the air filter periodically to maintain the air conditioner
in the best condition for a long period of time.
IMPORTANT When cleaning the air conditioner, turn it off and pull out
the power plug.
1
Hold the air filter handle, slightly pull it to the left side and open the front grille.
➢
The removal of the front grille makes it easier to clean the air
conditioner. Open the grille as much as possible.
CAUTION
Removal and Reassembly of the Front Grille
For user's safety, a safety clip has been installed in the front grille.
1 Grasp the lower part of the
front grille and the air filter
handle, then open the grille.
Safety clip
2 Remove the safety clip and
the front grille.
3 When reassembling the front
grille, you should install the
safety clip again.
2
Pull the air filter to the right side.
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, insert the air filter back into its original position.
5
Wipe the surface of the unit with a neutral detergent and then wipe it again
with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)
➢
If you...
Then...
Will not be using the
air conditioner for a
long period of time
◆ Set the fan going for a few hours to
dry the inside of the air conditioner
thoroughly.
◆ Switch the air conditioner off and
unplug it from the wall socket.
◆ Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan going for a few hours to dry
the inside of the air conditioner
thoroughly.
The air conditioner has two or three
grille grooves depending on the model.
E-17
Cleaning Your Air Conditioner (✴✴✴✴AA✴✴✴ models)
Be sure to clean the air filter periodically to maintain the air conditioner
in the best condition for a long period of time.
☛
1
When cleaning the air conditioner, turn it off and pull out the
power plug.
Open the front grille by pulling on the tabs of the unit.
➢
The removal of the front grille makes it easier to clean the air
conditioner. After opening the front grille, lift it up as much as possible,
then pull down to release it.
2
Grasp the handle on the air filter and lift it slightly and then out to the front.
3
Remove all dust on the air filter with a vacuum cleaner or brush.
4
When you have finished, insert the air filter back into its original position.
5
Wipe the surface of the unit with a neutral detergent
and then wipe it again with dry cloth.
(Be sure not to use benzene, solvent or other chemical products.)
Front grille
Front grille
Grille groove
Body guide
E-18
➢
If you...
Then...
Will not be using the
air conditioner for a
long period of time
◆ Set the fan to “FAN” and let it for a few
hours to dry the inside of the air
conditioner thoroughly.
◆ Switch the air conditioner off and
unplug it from the wall socket.
◆ Clean the filter and outer surfaces.
Have not used the air
conditioner for a long
period of time
Set the fan to “FAN” and let it run for
a few hours to dry the inside of the air
conditioner thoroughly.
ENGLISH
Solving Common Problems
Before contacting the after-sales service, perform the following simple checks. They may save
you the time and expense of an unnecessary call.
Problem
Explanation/Solution
The air conditioner does not
operate at all triggered.
◆
◆
◆
Check that the circuit breaker used for the air conditioner has not been
triggered.
Check that the power cable is plugged into a wall socket and the
socket is switched on, if necessary.
Check that the operating mode indicator(COOL, FAN or HEAT) on
the unit is lit up; if necessary press (On/Off) on the remote control
or unit.
The air conditioner does not
operate with the remote control
◆
◆
◆
Check that there are no obstacles between you and the unit.
Replace the remote control batteries if necessary.
Check that you are close enough to the unit (seven metres/yards
or less).
No beep is heard when you press
(On/Off) on the remote control
◆
Check that you are pointing the remote control at the remote
control sensor on the unit.
Replace the remote control batteries if necessary.
◆
The air conditioner does not cool or
heat.
◆
◆
◆
◆
Check that the correct operating mode has been selected
COOL or HEAT.
The room temperature may be too low or too high.
Dust may be blocking the air filter; refer to page 17 or 18 for
cleaning instructions.
Check that there is no obstacle blocking the air flow into or out of
the unit.
When heating, the required room
temperature is never reached and
the air conditioner frequently stops
◆
◆
◆
Check that the required temperature has been set correctly.
Increase the fan speed.
If the air flow is directed downwards, direct it upwards.
The air flow direction does not
change when you press AIR SWING
◆
Check that the air conditioner has been switched on; if necessary,
press (On/Off) on the remote control or unit.
The timer is not correctly triggered
◆
Check that the timer has been programmed correctly;
see page 12~14.
Odours are permeated in the room
during air conditioning
◆
Air the room.
Technical Specifications
Design and specifications are subject to change without notice.
Model
✴✴✴✴✴✴✴EA/EB
Power Supply
220-240V~, 50Hz
E-19
Method of Installation
Before installation, be sure to check the installation area or the air
conditioner, and drain hose.
Checkpoints prior to installation
1 Check the cabinet and front grille of the unit for any harmful defects
such as scratches.
2 Be sure to check the power supply.
- Refer to the specifications on the label attached to the unit.
Installation Conditions
1 As the unit is heavy, the wall or window of the installation area should
have sufficient strength and durability for operation of the air conditioner,
and for prevention of any vibration or noise.
If it is weak, reinforcement work should be performed separately.
2 It is advisable to install the air conditioner in the north or west side to
prevent the effect of direct sunlight.
When installing it in the south or east side due to unavoidable
circumstances, it is advisable to install the sunshade to prevent the
direct sunlight.
In this case, take care not to cause any hindrance to the flow of outside air.
3 When installing the air conditioner, be sure to obtain sufficient space on
the rear side of the unit for smooth flow of air.
When operating the air conditioner in closed areas such as inner building
with cooling operation, and result in trouble with the unit.
See the illustration below.
Awning
85mm
min.
300mm
“A”
500mm
500mm
500mm
Fence, wall
or other
obstacle
Approx.3˚
Model
“A”
✴✴✴✴✴✴S✴✴
180mm
✴✴✴✴✴✴J✴✴
220mm
✴✴✴✴✴✴M✴✴
240mm
750mm
➢
150mm min.
◆ If the wall is greater than 150mm thick,
cut the wall back on a 45˚ angle if possible.
45˚
100mm or more
E-20
45˚
ENGLISH
Installation of the Drain Tube
Rear
Fix the drain tube as shown in the figure.
Rubber cap
Gasket
Drain Tube
Screws(2EA)
Installation of the Drain Pan
The procedure for installing the drain pan should be determined by the
condition of the installing area.
◆ In the case of an area where the drain pan can not be directly
installed on the rear side of the unit after installing the air conditioner.
Example: High storage
1
Open the front grille ; refer to page 17 or 18.
2
Remove the screw located at the lower section of the front grille.
It is secured in the
section depending on the model.
3
Remove the front panel.
3-1 Press both sides of the cabinet in the direction of the arrow
as shown in the figure.
3-2 Pull the lower part of the front panel slightly forward.
(below three inches)
Front panel
Screw
3-3 Lift the front panel upward.
☛
Applying excessive force to remove the front panel
may cause damage to the tab ; be sure not to use
excessive force.
4
Remove two screws on the lower, right and left sides of the unit.
5
Remove the chassis from the cabinet.
6
Remove the rubber cap inserted into the basepan.
Drain Pan
Rear
7
Fix the drain pan as shown in the figure, and then connect the drain hose.
(You can use any commercially-available drain hose.)
8
Install the cabinet at the specified area after installing the drain pan,
and then re-assemble it in the original condition.
➢
Secure the front panel to the case by replacing the screw removed in
step 2. If a screw not removed in step 2, secure the panel with a
supplied screw.
Rubber cap
Drain Hose
Screw
Bottom-Side View with
Drain Pan and Hose in Place
◆ In the case of an area where the drain pan can be directly installed
on the rear side of the unit after installing the air conditioner.
1
Follow steps 6 and 7 only
E-21
THIS AIR CONDITIONER IS MANUFACTURED BY:
ESTE ACONDICIONADOR DE AIRE HA SIDO FABRICADO POR:
CE CLIMATISEUR EST FABRIQUÉ PAR:
ESTE APARELHO DE AR CONDICIONADO É FABRICADO POR:
QUESTO CONDIZIONATORE D’ARIA È PRODOTTO DA:
Printed in Korea