HT-DL100(-Cover(GB)
11/6/02
14:35
Page 2
DIGITAL HOME
THEATER SYSTEM
HT-DL100
Instruction Manual
Volume
Standby
VIDEO
Function
Open/close
Phones
COMPACT
COMPACT
DOLBY
D I G I T A L
VIDEO
DIGITAL AUDIO
DIGITAL VIDEO
HT-DL100(GB)
11/6/02
14:33
Page 1
Safety Warnings
CLASS 1 LASER PRODUCT
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE REAR COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This Compact Disc player is classified as a CLASS 1
LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED, AVOID
EXPOSURE TO BEAM.
This symbol indicates that dangerous voltage which can cause electric shock is present inside
this unit.
This symbol alerts you to important operating and maintenance instructions accompanying
the unit.
WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
1
HT-DL100(GB)
11/6/02
14:33
Page 2
Precautions
Volume
VIDEO
Standby
OPEN/CLOSE
Function
Phones
Volume
Standby
VIDEO
MIC Vol .
Function
Min
Max
OPEN/CLOSE
Phones
MIC
Setting up
Ensure that the mains supply in your house complies whit that indicated on the identification sticker located at the back of your play. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (7~10cm). Make sure the ventilation slots
are not covered. Do not stack other, or heavy devices on top over the player. Do not place the player on amplifiers or other equipmentwhich
may become hot. Before moving the player ensure the disc tray empty. This player is designed for continuous use. Switching off the DVD
player to the stand-by mode dose not disconnect the electricity supply In order to separate the player completely from the mains,it has to be
disconnected by unplugging the main plug, especially when left unused for a long period of time.
Volume
Standby
VIDEO
Function
OPEN/CLOSE
Phones
Caution
Battery
Do not expose the unit to direct sun radiation or other heat
sources.
The battery used in this product contains the chemicals that
are harmful to the environment.
This could lead to overheating and malfunction of the unit.
Do not dispose of batteries in the general household waster. It
is recommended that the replacement of the battery should be
done by technician.
Disc
Be careful handle your discs with care. Hold a disc whit finger on the border or
hole. Always place disc with the label facing upward (in case of a single side
disc ). Always use a soft cloth to clean disc if necessary, wipe from the centre to
the border. Always put disc back into their cases after playing and store in
vertical position. Always place the disc properly into the tray using the proper
guide area. Never use record cleaning sprays, benzine, static electricity liquids
or any other solvent, if the disc surface is dirty. Wipe gently with a soft
damp(water only) cloth, never wipe the disc in a circular motion, since circular
scratches are likely to occur and could case noise during playback.
2
HT-DL100(GB)
11/6/02
14:33
Page 3
DVD (Digital Versatile Disc) offers fantastic audio and video, thanks to Dolby
VIDEO
1
~ 6
Digital surround sound and MPEG-2 video compression technology. Now you can
enjoy these realistic effects in the home, as if you were in a movie theater or concert
hall.
DVD players and the discs are coded by region. These regional codes must match in
order for the disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is given on the rear panel of the player.
(Your DVD player with the same regional code will only play DVDs that are labled with identical region
codes.)
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
C
1992-1997 Dolby Laboratories Inc. All rights reserved.
Manufactured under license from Digital Theater System, Inc,
US Pat. 5,451,942 and other world-wide patents issued and
pending, “DTS” and “DTS Digital Surround” anre trademarks
of Digital Theater Systems, Inc. Copyright 1996 Digital
Theater Systems, Inc. All Rights Reserved.
3
HT-DL100(GB)
11/6/02
14:33
Page 4
Contents
Safety Warnings
1
Precautions
2
Description
5
Remote Control Unit
7
Connections
9
Before using the DVD Player
12
DVD Playback
13
Forward/Reverse Searching
15
Slow Playback/checking the Remaining Time
16
Repeat Playback
17
Using Disc Menu/Title
18
Program Playback
19
Selecting the Audio Language/ Subtitle Language
21
Various DVD Functions
22
¥To erlarge an image
¥Selecting the desired Screen Angle
¥To move directly to a title, chapter, or time
22
System Setup
23
Setting up the Language Features
25
Controlling a TV with the Remote
26
Speaker Setup
27
Listening to the Radio
31
Presetting stations
32
DSP/Sleep Functions
33
Using the Microphone
34
Troubleshooting
35
Cautions on Hadling and Stroing Discs
37
Disc Type and Protection
38
Specification
39
Reference
41
22
22
4
HT-DL100(GB)
11/6/02
14:33
Page 5
Description
Front Panel
Function button
Play/Pause (
Power (
) button
Stop ( ) button
Tuning Down & Skip (
Tuning up & Skip (
) button
) buttons
) buttons
Standby indicator
Volume control
Volume
Standby
VIDEO
Function
Open/Close
Phones
Open/Close button
Disc Tray
Headphone Jack
Display
PBC
indicator
TUNER indicator
TITLE indicator
STEREO indicator
SURROUND
indicator
PRO LOGIC indicator
PROGRAM
indicator
DTS Disc indicator
TUNED ST
PRO LOGIC
D I G ITAL
TITLE
PROGRAM
RADIO
FREQUENCY
indicator
DSP
indicator
PBC MHZ
DSP KHZ
LINEAR PCM
L
C
R
LFE
LS S RS
SPEAKER indicator
DOLBY DIGITAL
indicator
5
LINEAR PCM indicator
System Statis Display
HT-DL100(GB)
11/6/02
14:33
Page 6
Rear Panel
External Digital Component
Input Connectors
External Video Component Input Connector
External Audio Component Input Connector
Use these for connections to external
equipment capable of digital output.
AM Antenna
Connector
FM Antenna
Connector
S-Video Output Connector
5.1 Channel Speaker
Output Terminals
If the TV is equipped with an S-Video
input connector (S-VIDEO IN), connect it
to the player's S-Video output jack.
COMPONENT VIDEO
OUTPUT jacks
Connect a TV with the
component video input
jacks to these jacks.
Video Output Connector
Connect the TV's video input jacks
(VIDEO IN) to the VIDEO OUT
connector.
Accessories
Remote Control
Video/Audio Cable
AM Antenna
FM Antenna
User's Manual
6
HT-DL100(GB)
11/6/02
14:33
Page 7
Remote Control Unit
DVD POWER button
TV
TV Power button
Channel
DVD
DVD button
Band
TUNER button
DVD
TUNER
AUX button
Title
Menu
Channel
Audio
Subtitle
Volume
AUX
AUX
TV
V/VIDEO
TV/VIDEO button
Band
Title
Menu
Subtitle
Audio
MO/ST
Title button
Menu button
Subtitle button
Audio
TV Channel Selection button
TV Volume Control button
TUNER
Play/Pause button
MO/ST
Display
Return
Go To
Stop button
TV/VIDEO
Skip buttons
DVD/CD/TUNER
Tuning Up/Down button
MO/ST(mono/stereo) button
Tuning
Down
Up
Display
Return
Go To
Display button
Return button
Go To button
Direction/Enter button
Enter
+
Volume
DSP Mode
Effect
Mute
DSP button
Effect button
Number(0~9)
buttons
Slow button
Sound Edit
1
2
3
4
5
6
7
8
9
TV System/Zoom button
Speaker output volume control
Sleep button
Mute button
Sound Edit
SPK Mode
Pro Logic
Slow
Setup
Test Tone
D.R.C
Clear
Program
Step
Remain
Echo
SPK Mode
Pro Logic
0
Angle
Angle button
Repeat button
Volume Control buttons
Sleep
TV/System
Zoom
Repeat
Repeat
Test Tone
Sound Edit button
SPK Mode button
Pro Logic button
Test Tone button
A B
Clear button
Step button
Repeat A↔B button
Setup button
D.R.C button
Echo button (OPTION)
Program button
Remain button
7
HT-DL100(GB)
11/6/02
14:33
Page 8
Range of Operation of the Remote Control
Insert Remote Batteries
1
Remove the battery cover on
the back of the remote by
pressing down and sliding the
cover in the direction of the
arrow.
The remote control can be used up to
approximately 23 feet/7 meters in a straight line.
It can also be operated at a horizontal angle of
up to 30° from the remote control sensor.
Volume
Standby
VIDEO
Funetion
DVD HOME THEATER SYSTEM HT-D100
Phones
2
3
Insert two 1.5V AAA batteries,
paying attention to the correct
polarities (+ and –).
30
30
7~10m
Replace the battery cover.
Connect Video to TV
IN
COMPONENT OUT
PR
PB
VIDEO
Composite Video (Good Quality)
Connect the supplied video cable from the VIDEO
OUT jack on the back panel of the system to the
VIDEO IN jack on your television.
ANTENN A
ANTENNA
S-VIDEO
Y
AM
AUX IN
VIDEO OUT
L
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
R
Component
Video
Composite
Video
S-Video
FM
75
S-Video (Better Quality)
If you television is equipped with an S-Video
input, connect an S-Video cable (not supplied)
from the S-VIDEO OUT jack on the back panel of
the system to the S-VIDEO IN jack on your
television.
Conponent Video (Best Quality)
If your television is equipped with Component
Video inputs, connect a component video cable
(not supplied) fron the Pr, Pb and Y jacks on the
back panel of the system to the corresponding
jacks on your television.
8
HT-DL100(GB)
11/6/02
14:33
Page 9
Place and Connect Speakers
Speaker Place ment
Arrange the 6 speakers as shown in your listening area.
● Front Speakers : Set the front speakers so that they are aligned at ear level and at a horizontal angle of 45 degrees to the primary
listening area.
● Rear Speakers : Set the surround speakers further back, parallel to the walls, at 2 to 3 feet above the ear level of the primary
listening area. If the space behind the listening area is limited (i.e., close to the wall), place the rear speakers facing each other on
either side.
● Center Speaker : The center speaker should be positioned with its top surface flush with the front speakers. However, you may
place the speaker either on top of or next to your TV set.
● Subwoofer : Place the subwoofer at any convenient location within the vicinity of the listening area.
Speaker Connections
1. Make sure the power is turned off before connecting the speakers to prevent possible damage to the speakers.
2. Connect each red and black speaker wire to the system’s back panel as shown, being careful to connect each speaker to its
correctly labeled output.
3. To insert each color-coded wire, press down on the red and black thumb levers and then release them to lock the wires in place.
9
HT-DL100(GB)
11/6/02
14:33
Page 10
Connect Antenna
AM Loop Antenna
1. Complete assembly of the supplied AM loop antenna by
rotating the base and snapping it into place.
2. Connect the two wires from the AM loop antenna to the AM
ANTENNA connector on the back panel. Press down on the
thumb lever to insert each wire, and then release to lock the
wires in place.
VIDEO
ANTENN A
ANTENNA
S-VIDEO
AM
VIDEO OUT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
FM
75
FM Antenna
Connect the supplied FM antenna to the “FM 75Ω COAXIAL”
connector on the back panel. If noise or interference occurs, use
an external antenna with a 75Ω coaxial cable (not supplied).
Connect the supplied
AM and FM antennas
Connecting your System to the Power Supply
The main lead must be plugged into an appropriate socket.
Before plugging your system into a main socket, you must check
the voltage setting (OPTIONAL). If the voltage of the socket does
not correspond to the setting on the rear of the unit, you may
seriously damage your system.
SPEAKERS
1. Check the position of the voltage selector on the rear of the
system (OPTIONAL).
2. Plug the main lead (marked AC Cord on the rear of the
system) into an appropriate socket.
3. Press the On/Standby button to switch your DVD Player
system on.
IMPEDANCE
10
HT-DL100(GB)
11/6/02
14:33
Page 11
Connections
AUX Connections
Use these connections if necessary.
External Digital
Components
TV
For connection to external
equipment with digital
output.
Example: CD recorders, MD
(Mini Disc) D/A converters or
other components equipped with
digital output jacks
VIDEO IN
Picture can be shown
only when the TV’s video
output connector (VIDEO
OUT) is connected to the
AUX IN connector.
Optical Cable
DIGITAL IN
VIDEO IN
COMPONENT OUT
PR
PB
VIDEO
ANTENN A
S-VIDEO
Y
OPC.
AM
R-FRONT-L
AUX IN
VIDEO OUT
Video Cable
L
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
FM
75
R
6
Audio Cable (Red/White)
SPEAKERS
If the external analog
component has only one
output jack, you may
connect either L or R.
External Analog
Components
¥ Always connect the video and
R
L
VIDEO OUT
Connect to external equipment with
analog output.
Example: Video, TV, LDP, etc.
Making Digital/Analog Input Selection
11
Remote Control
Press the AUX button and select either DIGITAL IN or ANALOG IN.
Main Unit
Press the Function button and select either DIGITAL IN or ANALOG IN.
audio connection cables to the
equivalent colored jack.
¥Even if DIGITAL IN is selected, if
the video input jack of an external
analog component is connected to
the player’s VIDEO IN connector,
the player will still output a video
signal from the analog component.
HT-DL100(GB)
11/6/02
14:33
Page 12
Before Using the DVD Player
Your DVD player is capable of playing DVD, VCD, and CD discs.
User instructions may vary depending on the type of disc. Read the instructions
carefully before use.
1
2
Turn on the power
Prepe- to your DVD player
rations and TV.
before
use
Select a video mode by
pressing the TV/VIDEO
button.
Press the DVD button
to select the DVD input
function.
TV/VIDEO
DVD
TV
¥
3
The word INVALID appears on screen!
If this message appears on the TV screen while buttons are being
operate, the operation is not possible with that particalar disc.
¥
If your TV model is not SAMSUNG, refer to “Remote Control Unit
Setup” on page 26.
TV System
TV System Selection
Zoom
Press the TV System button while in stop mode.
¥ Each time the TV System button is pressed, “NTSC, PAL,
SECAM(Option)” are selected in this order.
Different countries use different types of TV broadcast systems, video,
audio and channel systems.
Example : The player cannot playback PAL-encoded DVD with NTSC-TV.
CD-R/RW playback compatibility
¥Your DVD player can also play CD-R and CD-RW discs recorded in digital
audio format. When recording your own CD-R or CD-RW discs, make sure that
the recording session is properly terminated, or they will not be playable.
(Depending on disc properties and recording quality, some CD-R/RW may not
be playable.)
¥CD-RW has a lower reflection rate than CD-R media and consequently it will
take a longer to read CD-R discs.
¥CD-RW discs recorded at high speed tend to be difficult for the DVD player to
read. If the recording speed for the CD-RW disc is not predetermined, write it
at low speed.
12
HT-DL100(GB)
11/6/02
14:33
Page 13
DVD Playback
Press the Open/Close button
to open the disc tray.
OPEN/CLOSE
¥ The button is located only on the Front
Panel of the player (not on the remote).
Insert a DVD disc.
VIDEO
Playback starts
automatically.
¥ Press the Open/Close button again to
close the disc tray.
Press the Open/Close button
again to close the disc tray.
OPEN/CLOSE
Stopping Playback
Pausing Playback
Press the Play/Pause (
playback.
) button during
¥ To resume, press the Play/Pause (
)
button again.
Depending on the disc, the initial disc
information screen may look disc to disc.
13
Press the Stop (
) button during playback.
¥During playback, when the Stop ( )button is pressed,
the position is stored in the memory, and
PRESTOP is shown on the display.
When the Play/Pause (
) button or Return button is
pressed subsequently , playback resumes from the
position at which it was stopped.
¥If the Stop ( ) button is pressed a second time, the
resume play' memory function is canceled, and
STOP is shown on the display. When the Play/Pause
(
)button is pressed, playback starts from the
beginning.
HT-DL100(GB)
11/6/02
14:33
Page 14
Display
Using the On-Screen Display
Press the Display button on the remote.
Display
T1/2
VIDEO
DVD indicator
C 1/8
00:00:00
TITLE indicator
CHAPTER indicator TITLE ELAPSED
indicator
Display
VIDEO
KOR
KOR 1/3
SUBTITLE LANGUAGE
indicator
AUDIO LANGUAGE
indicator
OFF
1/1
ANGLE indicator
REPEAT indicator
DISC TYPE indicator
Display
The On-Screen Display disappears.
Mute
What is a Title?
Turning the sound off temporarily?
A movie contained in a
DVD disc.
Press the Mute button during playback.
What is a Chapter?
Each Title on a DVD
disc is divided into
several smaller sections
called "chapters".
¥This operation may be useful when you need
to greet the guests or answer the telephone.
If the player is left for more than 5 minutes
in pause mode, it will stop.
14
HT-DL100(GB)
11/6/02
14:33
Page 15
Forward/Reverse Searching
During playback, you can search quickly through a chapter or track for a specific scene
or tune.
button is pressed
Each time the
▲
▲
Each time the
button.
▲
▲
and
▲
▲
Press the
▲
▲
High-Speed Playback
button is pressed
X2
X2
X4
X4
X8
X8
PLAY
PLAY
and
▲
▲
Press the
▲
▲
Skipping through a Chapter
button.
¥ Each time the button is pressed during playback, it moves to the next
or previous chapter and plays it.
¥ However, you cannot skip forward or backward through consecutive
the chapters.
SEARCH
SEARCH
Step
Playing Frame by Frame
Press the Step button.
¥ The picture moves forward one frame each time the button is pressed.
15
No sound is heard during
high-speed playback, slow
playback, and step motion.
HT-DL100(GB)
11/6/02
14:33
Page 16
Slow Playback/Checking the
Remaining Time
Playing Slowly
Slow
Press the Slow button.
Each time the Slow button is pressed
SLOW 1/2
SLOW 1/4
The slow playback speed changes
and the selections (1/2X, 1/4X, 1/8X,
1/16X and normal play) are repeated.
PLAY
When playing a VCD or CD,
the reverse slow playback will
not work.
Remain
Checking the Remaining Time
Press the Remain button.
¥ For checking check the total time and the
remaining time of a title or chapter being played.
Each time the Remain button is pressed
TITLE TIME
TRACK TIME
REMAIN TIME : TITLE
REMAIN TIME : TRACK
CHAPTER TIME
DISC TIME
REMAIN TIME : CHAPTER
REMAIN TIME : DISC
16
HT-DL100(GB)
11/6/02
14:33
Page 17
Repeat Playback
Repeat playback allows you to repeat a chapter, title, or track.
Repeat
Playing Repeatedly
Press the Repeat button.
Each time the Repeat button is pressed
REPEAT : CHAPTER
REPEAT : ONE
REPEAT : TITLE
REPEAT : DISC
REPEAT OFF
REPEAT OFF
Repeat playback operation is not possible with
version 2.0 VCD discs if PBC is turned on.
To operate this feature, press the MENU
button, and then select "PBC OFF".
A↔B Repeat Playback
1
2
Press the Repeat A↔B button at the
beginning (A) of the segment you want to
review.
Press the Repeat A↔B button again at
the end (B) of the segment you want to
review.
Repeat
A B
REPEAT : A-
REPEAT : A - B
¥ The segment will begin repeating.
To return to normal playback
Press the Repeat A<–>B button again.
17
REPEAT OFF
HT-DL100(GB)
11/6/02
14:33
Page 18
Using Disc Menu/Title
Menu
To Select the Disc Menu
You can use the menus for the audio language,
subtitle language, profile, etc. DVD menu contents
differ from disc to disc.
¥ The Menu Screen appears.
3
Press the Enter button.
▲
Press the Menu button during
playback.
2
Use the Up/Down (▲ / ▼ ) or
Left/Right( / ) button to
access the different features.
▲
1
¥ The selected item will play.
Title
Using the Title Menu
For DVDs containing multiple titles, you can
view the title of each movie.
Depending on the disc, this function may either
not work at all, or may work differently.
18
HT-DL100(GB)
11/6/02
14:33
Page 19
Program Playback
Use this function with video and music CDs to play the tracks in a particular order.
Program
To Program Tracks in a particualr order
2
Press the Program button.
Press the Enter button then
use the Number buttons to
select the desired title.
PROGRAM MENU SELECT : ENTER
TITLE CHAPT
1
2
3
4
5
PREVIOUS
PLAY :
TITLE CHAPT
6
7
8
9
10
NEXT
FINISH : PROGRAM
▲
also just the
/ / ▲ / ▼ ) button.
PROGRAM MENU SELECT : ENTER
TITLE CHAPT
1
1
2
3
4
5
PREVIOUS
PLAY :
4
Press the Enter button.
¥ The selected track number is
programming and the cursor
moves to the next number.
PROGRAM MENU SELECT : ENTER
TITLE CHAPT
1
1
2
2
3
4
5
PREVIOUS
PLAY :
TITLE CHAPT
6
7
8
9
10
NEXT
FINISH : PROGRAM
To Cancel the Programming
19
TITLE CHAPT
6
7
8
9
10
NEXT
FINISH : PROGRAM
5
At this time, you can continue
programming if you want to.
Press the Enter button, then
use the Number buttons to
select the desired chapter.
¥ You can use also just the
Left/Right (
/
▲
Left/Right (
▲
¥ You can use
3
▲
1
/ ▲ / ▼ ) button.
PROGRAM MENU SELECT : ENTER
TITLE CHAPT
1
2
1
2
3
4
5
PREVIOUS
PLAY :
TITLE CHAPT
6
7
8
9
10
NEXT
FINISH : PROGRAM
To Playback the
Tracks in the
Programmed Order
¥ When programming more than
10 tracks, select EXT and
then press the Enter button.
The program selection screen
where you can program up to
10 additional tracks appears.
Press the Play/Pause
(
) button.
PROGRAM MENU SELECT : ENTER
TITLE CHAPT
1
2
1
1
2
2
1
7
3
2
3
4
2
4
5
PREVIOUS
PLAY :
6
7
8
9
10
TITLE CHAPT
4
1
6
2
3
4
5
5
1
2
NEXT
FINISH : PROGRAM
Press either the Program button or Stop (
) button.
HT-DL100(GB)
11/6/02
14:33
Page 20
To Change the Program
1
2
3
Press the Clear button and
then press the Number
buttons.
¥ The cursor moves to the next
¥ You can use also just the
number when the Enter button
is pressed again.
4
Left/Right (
/
▲
Press the Enter button to
select the title or chapter to be
changed.
▲
Press the Up/Down ( ▲ / ▼ )
button to select the track
number to be changed.
) button.
5
Press the Enter button.
Repeat steps 1-4 above to
change the program.
¥ The cursor moves to the
number below.
To delete the entire Program
¥ Press the Stop (
) button twice during playback.
¥ Press the Stop (
) button once when in the Stop mode.
¥ Press the Open/Close (
) button on the main unit.
The disc tray will open and then close. The program will then
be deleted.
When you have entered a
wrong number
Clear
You can program or change
particular tracks for VCD or CD
discs in the same manner.
Press the Clear button.
¥ When you want to delete a selection during
programming, select the track (or chapter, or title) to be
deleted and then press the Clear button.
20
HT-DL100(GB)
11/6/02
14:33
Page 21
Selecting the Audio Language/Subtitle Language
Audio
Selecting the Audio Language
MO/ST
Press the Audio button.
¥ Depending on the number of languages recorded on a DVD disc, a
different audio language (KOREAN, ENGLISH, JAPANESE, etc.) is
selected each time the button is pressed.
KOR
VIDEO
KOR 1/3
OFF
1/1
ENG 2/3
JAP 3/3
¥ Depending on the disc, DTS or DIGITAL PRO LOGIC can be
selected.
Subtitle
Selecting the Subtitle Language
Press the Subtitle button.
¥ Depending on the number of languages recorded on a DVD disc, a
different subtitle language (KOREAN, ENGLISH, JAPANESE, etc.)
is selected each time the button is pressed.
¥ To make the subtitles disappear, select "OFF".
VIDEO
KOR 1/3
KOR 1/1
OFF
1/1
ENG 2/3
JAP 3/3
OFF
¥ The word INVALID appears on the TV screen!
¥ If this message appears on the TV screen while buttons are being
operated, that operation is not possible with that particular disc.
¥ Depending on the disc, the audio or subtitle language function
may not work.
21
HT-DL100(GB)
11/6/02
14:33
Page 22
Various DVD Functions
TV System
To enlarge an image
Zoom
Press the Zoom button.
¥ Only 2X zoom
¥ Images can be enlarged 2x and 4x.
¥ During DVD playback, press the
operation is
possible during
VCD playback.
ZOOM button to zoom in
2X/4X/normal, in that order.
Angle
Selecting the desired Screen Angle
Press the Angle button.
¥ This function only works with discs on which multiple angles have been recorded.
¥ During playback, press the Angle button to select the desired angle in 1/3, 2/3, 3/3,
normal, in that order.
OFF
1/3
2/3
3/3
Go To
To move directly to a title, chapter, or time
Press the Go To button.
Press Number(0~9) button or the
Left/Right ( / ) button.
▲
2
¥ Each time the button is pressed, it repeats as shown below.
VIDEO
TITLE
T1/2
C 1/8
00:00:00
VIDEO
T1/2
CHAPTER
C 1/8
00:00:00
VIDEO
TIME
T1/2
C 1/8
:
00:00:00
:
▲
1
¥ Each The desired scene is
located and then played.
¥ Depending on the disc, the Title
function may not work.
22
HT-DL100(GB)
11/6/02
14:33
Page 23
System Setup
You can use the DVD player's Setup function to select the TV screen ratio,
rating limit, or digital output mode.
Setup
To Set up the System
1
2
LANGUAGES
▲
Press the Left/Right ( / )
button to select the system.
SYSTEM
LANGUAGES
OSD LANGUAGE
ENGLISH
TV SCREEN
AUDIO
CHINESE
CHINESE
CHINESE
RATING LEVEL
DIGITAL OUTPUT
SUBTITLE
MENU LANGUAGE
: Move
Press the Up/Down ( ▲ / ▼ )
button to select the desired
item.
▲
From the stop mode, press
the Setup button.
3
Setup : Exit
SYSTEM
: Move
LANGUAGES
TV SCREEN
4:3 LB
OFF
BITSTREAM
RATING LEVEL
DIGITAL OUTPUT
Setup : Exit
: Move
4
▲
) button.
▲
RATING LEVEL
DIGITAL OUTPUT
: Move
SYSTEM
4:3 LB
OFF
BITSTREAM
SYSTEM
TV SCREEN
4:3 LB
OFF
: Move
Setup
¥ Press the Setup button again.
LANGUAGES
RATING LEVEL
DIGITAL OUTPUT
Setup : Exit
To End the System Setup
23
Setup : Exit
Press the Up/Down ( ▲ / ▼ ) button to select the
desired sub-item and then press the Enter
button.
¥ Move to the detailed items.
¥ Then press the Left ( ) button to return to the previous step.
TV SCREEN
4:3 LB
OFF
BITSTREAM
5
Press the Enter button or Right (
LANGUAGES
SYSTEM
BITSTREAM
LPCM
Setup : Exit
HT-DL100(GB)
11/6/02
14:33
Page 24
TV SCREEN(TV SCREEN RATIO)
Select when you want to watch a 16:9 screen ratio DVD movie on a TV with a 4:3 ratio screen.
4:3LB
LANGUAGES
TV SCREEN
RATING LEVEL
DIGITAL OUTPUT
: Move
SYSTEM
4:3 LB
OFF
BITSTREAM
4:3PS
16:9
Setup : Exit
You can see the full 16:9 picture, but black bars will appear at the
top and bottom of the screen.
You can only view the central portion of the 16:9 screen.
You can view in wide screen but the top and bottom of the picture
will be cut off.
¥ However if the movie is recorded in 4:3 ratio, you cannot view the full 16:9 picture with the
above functions.
RATING LEVEL
The Rating Level function works in conjunction with DVDs which have been assigned
a rating, to help control the type of DVD that your family watches.
LANGUAGES
TV SCREEN
RATING LEVEL
DIGITAL OUTPUT
: Move
SYSTEM
4:3 LB
OFF
BITSTREAM
Setup : Exit
LANGUAGES
SYSTEM
TV SCREEN
4:3 LB
RATING LEVEL
DIGITAL OUTPUT
BITSTREAM
: Move
2. Use the number(0~9) buttons to input
a 4-digit password.
¥ The player’s password is set to "7890" by
default.
When the rating level
password has been forgotten
While the player is in the stop
mode, hold the Stop ( ) button
down on the main unit for more than
5 seconds.
¥ "INITIAL" appears on the display and
all default settings will return to
Factory Preset.
Setup : Exit
LANGUAGES
SYSTEM
TV SCREEN
4:3 LB
RATING LEVEL
DIGITAL OUTPUT
: Move
1. Select RATING LEVEL, then press the
Enter button.
Setup : Exit
3.Use the Up/Down (▲ / ▼ ) button to select either RATING LEVEL or
NEW PASSWORD, and then press the Enter button.
¥ There are up to 8 rating levels on a disc.
¥ If LEVEL 6 is selected, a disc which contains rating LEVEL 7 and above cannot
be played.
¥ If you select NEW PASSWORD, the screen changes and enables you to enter
the new password.
DIGITAL OUTPUT
BITSTREAM
LANGUAGES
TV SCREEN
RATING LEVEL
DIGITAL OUTPUT
: Move
Select this if Dolby Digital 5.1 CH connections have been made.
SYSTEM
4:3 LB
OFF
BITSTREAM
LPCM
Select this otherwise.
Setup : Exit
24
HT-DL100(GB)
11/6/02
14:33
Page 25
Setting up the Language Features
Using the DVD player's Setup function, you can customize the Menu
Language, Subtitle Language, and Disc Menu Language.
Setup
To set up the language feature
1
2
Press the Setup button from the stop mode.
Press the Up/Down ( ▲ / ▼ ) button to select
the desired item.
LANGUAGES
SYSTEM
OSD LANGUAGE
ENGLISH
AUDIO
CHINESE
CHINESE
CHINESE
SUBTITLE
MENU LANGUAGE
: Move
LANGUAGES
SYSTEM
OSD LANGUAGE
ENGLISH
AUDIO
CHINESE
CHINESE
CHI NESE
SUBTITLE
MENU LANGUAGE
Setup : Exit
: Move
Setup : Exit
OSD LANGUAGE
(PLAYER MENU LANGUAGE)
AUDIO
(AUDIO LANGUAGE)
SUBTITLE
MENU LANGUAGE
(SUBTITLE LANGUAGE)
3
(DISC MENU LANGUAGE)
4
▲
Press the Enter button or Right (
) button.
Press the Up/Down ( ▲ / ▼ ) button to select
the desired language and then press the Enter
button.
▲
¥ Move to the language features.
¥ Then press the Left ( ) button to return the previous step.
LANGUAGES
LANGUAGES
SYSTEM
ENGLISH
OSD LANGUAGE
ENGLISH
ENGLISH
AUDIO
CHINESE
CHINESE
ENGLISH
AUDIO
CHINESE
CHINESE
CHINESE
FRENCH
SUBTITLE
MENU LANGUAGE
: Move
SUBTITLE
MENU LANGUAGE
Setup : Exit
: Move
Setup
To End the Language Features Setup
¥ Press the Setup button again.
25
SYSTEM
OSD LANGUAGE
GERMAN
Setup
: Exit
JAPANESE
HT-DL100(GB)
11/6/02
14:33
Page 26
Controlling a TV with the Remote
1
Enter the code that corresponds to your brand while
holding down the TV(
) button on the remote control.
DVD
TUNER
Title
Menu
Audio
Subtitle
AUX
TV
Band
TV
3
Channel
Volume
MO/ST
Number(0~9)button
Display
Go To
Return
TV/VIDEO
DVD/CD/TUNER
Tuning
Down
Code
Brand
Code
Up
Brand
Enter
01
SAMSUNG 1
16
SHARP 3
02
SHARP 2
17
ZENITH
03
SONY
18
LG 3
04
MAGNAVOX
19
DAEWOO 8
+
Volume
Effect
Mute
1
2
3
4
5
6
7
8
9
DSP Mode
Sleep
AH59-00132A
Sound Edit
SPK Mode
05
SANYO 1
20
SANYO 2
06
LG 2
21
EMERSON
Pro Logic
Slow
Setup
Test Tone
D.R.C
Clear
0
Angle
TV System
Zoom
07
2
RCA
22
SHARP 3
Repeat
Repeat
Program
Step
Remain
Echo
A B
08
LG 1
23
SAMSUNG 4
09
TOSHIBA
24
MATSUSHITA
10
HITACHI
25
NOBLEX
11
JVC
26
TELEFUNKEN
12
PANASONIC 1
27
NEWSAN
13
MITSUBISHI 2
28
LOEWE
14
SAMSUNG 2
29
RCA2
15
SAMSUNG 3
¥ Depending on the type of
TV you have, some
operations cannot be
performed with the
remote.
¥ If your TV does not switch
from VIDEO mode to TV
mode, press the TV
POWER(
) button
twice.
Operate by pressing the TV function.
¥ Enter other codes for the same brand if the
first code does not work.
D.R.C
Dynamic range compression (DRC) function
This function allows for fullness of sound with Dolby Digital effect even
when playing at low volumes during nighttime listening.
Press the D.R.C button.
¥ The selection switches back and forth between
“D.R.C. On” and “D.R.C. Off” each time the
button is pressed.
¥ This function only works when in the Dolby Digital
mode.
TUNED
PRO LOGIC
D I G ITAL
TITLE
ST
PROGRAM
SURROUND
PBC MHZ
DSP KHZ
LINEAR PCM
L
C
R
LFE
LS S RS
26
HT-DL100(GB)
11/6/02
14:33
Page 27
Speaker Setup
Sound Edit
To set up Speaker Balance
2
Use the Left/Right (
adjustment.
¥ Each time the button is pressed the selection switches as shown below.
Example: 5.1CH Sound Setup
PRO LOGIC
D I G ITAL
OFF, range of -6~0
LINEAR PCM
L
LS
C
R
LFE
S RS
Front Speakers: L level, R level
PRO LOGIC
D I G ITAL
OFF, range of -6~-0
LINEAR PCM
L
LS
C
R
LFE
S RS
Rear Speakers: L level, R level
PRO LOGIC
D I G ITAL
OFF, range of -6~-00~+6
LINEAR PCM
L
LS
C
R
LFE
S RS
Center Speaker
PRO LOGIC
D I G ITAL
LINEAR PCM
L
LS
OFF, range of -6~-00~+6
C
R
LFE
S RS
Rear Speakers
PRO LOGIC
D I G ITAL
LINEAR PCM
L
LS
C
R
LFE
S RS
OFF, range of -10~-00+10
Subwoofer Speaker
The display changes depending on the current audio output
mode (DSP, PROLOGIC, 3-STEREO, STEREO, etc.).
27
/
▲
Press the Sound Edit button.
▲
1
) button to make
HT-DL100(GB)
11/6/02
14:33
Page 28
Test Tone
Speaker Setting Methods
Press the TEST TONE button.
¥ Depending on the number of languages recorded on a DVD disc, a
different audio language (KOREAN, ENGLISH, JAPANESE, etc.) is
selected each time the button is pressed.
L
Test Tone
C
LFE
LS
To End the Language Features Setup
R
RS
¥ Press the Test Tone button again.
While in DSP or PRO LOGIC mode, TEST TONE may
operate differently for VCDs or CDs
Pro Logic
Selecting Dolby Pro Logic
Press the Pro Logic button.
Converts encoded Dolby Pro Logic 2 channel sound (example: external input
received by Stereo VCR is Dolby Digital 2 channel) to 4 channel sound. This
feature is unavailable in DVD mode.
1
2
Press the PRO LOGIC button.
Press the AUX button or a TUNER BAND
button.
¥ Select from FM, AM, DIGITAL IN and
ANALOG IN.
¥ You can also press the Stop ( )
button on the front panel of the main unit.
¥ Each time tje Pro Logic button is pressed
PRO LOGIC
L
C
LFE
S
R
Use only when Rear Speakers are connected.
Center channel signals are output through
Front Speakers (L, R).
PRO LOGIC
L
C
LFE
R
Use only when Rear Speakers are not connected.
Rear channel signals are output through Front
Speakers (L, R).
L
R
LFE
Use only when Front Speakers (L, R) are
connected.
28
HT-DL100(GB)
11/6/02
14:33
Page 29
Speaker Setup
SPK Mode
Setting up Speaker Mode
and Delay Time
Press the SPK Mode button.
¥ Each time the button is pressed, a different mode selection is
displayed on the front panel display as shown below.
DIGITAL
L
C
LFT
F SP SMALL
Front speaker: Small
C SP SMALL
Center speaker: Small
C
LFT
R
C
LFT
R
F SP LARGE
RS
DIGITAL
DIGITAL
L
L
LS
▲
R
RS
R SP SMALL
You can select either R-SP SMALL or
R-SP NONE by using the Left/Right
Rear speaker: Not found ( / ) buttons.
L
LS
RS
R
C SP NONE
RS
▲
Rear speaker: Small
C
LFT
▲
C
LFT
You can select tither C-SP SMALL or
C-SP NONE by using the Left/Right
Center speaker: Not found ( / ) buttons.
DIGITAL
DIGITAL
L
LS
LS
M
o
d
e
R
RS
▲
S
p
e
a
k
e
r
LS
DIGITAL
L
C
LFT
LS
R
SW SP USE
RS
Subwoofer: Found
DIGITAL
L
C
LFT
LS
Delay
Time
R
C DEL
MS
Setting up Delay Time from 00~05ms
RS
Center Speaker Delay Time
DIGITAL
L
LS
C
LFT
R
R DEL
MS
Setting up Delay Time from 00~15ms
RS
Rear Speaker Delay Time
The display changes depending on the current audio output mode
(DSP, PROLOGIC, 3-STEREO, STEREO, etc.).
29
HT-DL100(GB)
11/6/02
14:33
Page 30
To set the delay time
(A)=Df-Dc
ßWhen 5.1 Channel Surround Sound is played,
you can enjoy the best sound if the distance
between you and each speaker is the same. You
can set Delay Time in the Center/Rear Speaker
to customize the sound to the acoustics of your
room.
ßSetting Center Speaker
If the distance of Dc is equal to or longer than the
distance of Df in the figure, set the mode as 0ms.
Otherwise, change the setting according to the
table on the table.
ßSetting Rear Speakers
If the distance of Df is equal to the distance of Ds
in the figure, set the mode as 0ms.
Otherwise, change the setting according to the
table.
Distance of (A)
Value(ms)
50
100
400
200
1.3
2.6
3.9
5.3
Ideal Center Speaker Position
Dc
Df
(B)=Df-Ds
Distance of (B)
Value(ms)
200
5.3
400
10.6
600
15.9
Dc: Distance from center speaker to
listening position
Df: Distance from front speakers to
listening position
Ds: Distance from rear speakers to
listening position
Ds
Ideal Rear Speaker Position
Arrange all speakers within a circle
as shown in the figure.
Speaker Setting Methods
Front Speakers
Set the front speakers so that their tweeters (high-range) are
aligned at about ear level and at a horizontal angle of 45° to the
prime listening position.
Volume
Standby
DIGITAL
COMPACT
SURROUND
DIGITAL VIDEO
DOLBY
VIDEO
DIGITAL
MIC Vol .
Function
Min
Max
OPEN/CLOSE
Phones
MIC
Center Speaker
Ideally the center speaker should be positioned with its top
surface flush with the front speakers. However, you may place
the speaker either on top or near the bottom of your TV set.
Rear Speakers
Set the rear speakers further back parallel to the walls, at
60 to 90 centimeters (2 to 3 feet) above prime listening
position ear level.
If the space behind the listening position is insufficient
(i.e., too close to the wall), place the rear speakers facing
each other on either side.
Subwoofer Speaker
Place the subwoofer at any convenient location within
the vicinity of the listening position.
30
HT-DL100(GB)
11/6/02
14:33
Page 31
Listening to the Radio
You can listen to the chosen band (FM or AM broadcast stations) by using either the
automatic tuning or manual tuning operation.
2
1
Remote
Control
Unit
Press the Tuner(Band)
button.
¥ The selection toggles back
and forth between "FM" and
"AM" each time the
Tuner(Band) button is
pressed.
Select a broadcast station.
Auto Station 1
When the
button is pressed, a preset
broadcast station is selected.
Auto Station 2
Hold in the
button. Automatic searching
begins, and then stops when a station is tuned in.
Manual Station Press the
button to tune to the chosen
station. The frequency changes incrementally in either
direction each time the corresponding button is pressed.
2
1
Main
Unit
Press the Function button to
select the desired band (AM
or FM).
Select a broadcast station.
Auto Station 1
Press the
button to select the PRESET mode.
Then press the
button to select a station
stored in the preset
Auto Station 2
Press the Stop (
) button to select the MANUAL
mode. Then hold in the
button to make
the unit begin automaticall searching for broadcast
stations.
Manual Station
Press the Stop ( ) button to select the MANUAL mode.
Press the
button to tune to the desired station.
The frequency changes incrementally in either direction each
time the corresponding button is pressed.
Audio
To Listen in Mono/Stereo
MO/ST
Press the MO/ST button. (only FM)
¥ The selection toggles back and forth between “STEREO” and “MONO”
each time the MO/ST button is pressed.
¥ In a poor reception areas, select Mono mode for a clear, interference-free
broadcast.
31
HT-DL100(GB)
11/6/02
14:33
Page 32
Presetting stations
A total of 30 broadcast stations (FM and AM combined) can be preset.
Example: Presetting FM 89.1 in the memory
2
▲
▲
Press the Tuner(Band) button
and select the FM band.
3
▲
▲
1
Use the
and
button to tune into 89.1
Select the MANUAL by
pressing the Stop ( ) button
on the main unit.
¥ The selection toggles back and forth between "FM" and "AM"
each time the Tuner(Band) button is pressed.
MHZ
L
MHZ
R
L
L
R
5
Press the Program button.
6
▲
▲
▲
▲
4
R
Use the
and
button to select FM2.
Press the Program button.
¥ The preset stations operation is
completed.
PROGRAM
L
MHZ
R
PROGRAM
L
R
MHZ
MHZ
L
R
¥ When using this feature for the
first time, be sure to store the
station in the preset memory at
FM1 as the unit does not come
preprogrammed with default
presets.
To change the Preset Stations
¥ Store the changes while repeating
To store other Channels
Repeat steps 3 to 5 above.
steps 1 to 4 above.
32
HT-DL100(GB)
11/6/02
14:33
Page 33
DSP/Sleep Function
DSP Mode
To Select a DSP
Press the DSP Mode button.
What is a DSP?
¥ The DSP mode toggles in the following
order each time the DSP button is pressed:
HALL ➔ THEATER ➔ PAVILION ➔
DANCE CLUB ➔ LIVE HOUSE ➔ OFF.
DSP synthetically recreates the sound
field to achieve a more realistic,
powerful sound.
DSP mode cannot be selected when a
microphone is connected.
Effect
To increase Effect level
Press the Effect button.
What is a Effect?
¥ The effect level can be set in steps from 1
to 4 (EFFECT1 ➔ EFFECT2 ➔ EFFECT3
➔ DEFAULT).
Each time the button is pressed the
selection moves to the next effect.
¥ The higher the number, the stronger the
DSP surround effect will be.
This sets the strength of the DSP
mode.
Sleep
To set up Sleep
Press the Sleep button.
What is the
Sleep function?
¥ Each time the button is pressed the
selection toggles as follows: 10 ➔ 20 ➔
30 ➔ 60 ➔90 ➔120 ➔150 ➔ OFF.
To Review Sleep Setting
You can set the delay time so that
the unit powers off automatically
after a preset period of time.
¥ The remaining time for the selected Sleep time is
displayed.
¥ Pressing the button once again changes the Sleep
time from the last setting.
33
HT-DL100(GB)
11/6/02
14:33
Page 34
Using the Microphone (OPTION)
You can have fun singing along by using a microphone (not supplied) input
while VCD, CD, or radio music is playing in background.
1
MICROPHONE
VOLUME control
Volume
MIC Vol .
Min
Max
MIC
Turning the control
knob clockwise
increases the
microphone volume
level. Counterclockwise rotation
decreases volume
level.
Connect the microphone to the
MICROPHONE jack on the main
unit.
¥ “ECHO 1” is shown on the display.
MICROPHONE jack
2
Press the Echo button on the
remote control unit.
¥ The display switches each time the
button is pressed as follows.
¥ If you connect a microphone during DTS
playback, no sound will be heard.
¥ If you connect a microphone while
playing a DVD not encoded with DTS,
2 channel sound will be produced.
¥ Microphone will only work during CD,
VCD or DVD playback.
Listening on headphones
Use headphones for private listening pleasure (not supplied).
Standby
VIDEO
Connect the headphones to the HEADPHONES jack of the front panel.
Function
OPEN/CLOSE
Phones
HEADPHONE jack
¥ No sound is produced from the speakers.
¥ To prevent hearing damage, do not raise the volume
level excessively when using headphones.
34
HT-DL100(GB)
11/6/02
14:33
Page 35
Troubleshooting
Problem
The disc tray does not
open.
Check
¥ Is the disc installed with the label side facing up?
¥ Is the power cord plugged securely into the power outlet?
¥ Turn off the power to the unit by pressing the Power (
) button
and turn it back on.
Disc does not play.
Playback does not start
immediately when the
Play/Pause button is pressed.
¥ Check the region number of the DVD.
¥ DVD discs purchased abroad may not be playable.
¥ This player cannot play CD-ROMs, DVD-ROMs, etc.
¥ Check the rating level of the DVD.
¥ Check whether the disc has any scratch marks or is deformed?
¥ Is the power cord plugged securely into the power outlet?
¥ No sound is heard during high-speed playback, slow playback,
No sound is produced.
and step motion playback modes.
¥ Are the speakers properly connected? Is the speaker Setup
correctly customized?
¥ Is the disc installed with the label side facing up?
¥ Is the disc severely damaged?
The disc may be dirty. Wipe off fingerprints or dirt.
Picture does not appear; sound
is not produced; the disc tray
opens 2-5 seconds later.
¥ Was the player moved suddenly from a cold pace to a warm one?
Sound quality is
irregular.
¥ Are the speaker cables loose?
¥ Is there any dirt or debris at the end of the speaker connector?
Dolby Digital 5.1 Channel
Surround Sound is not
being reproduced.
¥ Does the disc being played show the “Dolby Digital 5.1CH” mark ?
35
When condensation forms inside the player, remove the disc
and let the player stand for 1 or 2 hours with the power on. (You
can use the player after the condensation disappears.)
5.1-channel sound is reproduced only if the disc is recorded with
5.1 channel sound.
¥ Is the DVD player connected to the proper speakers?
HT-DL100(GB)
11/6/02
14:33
Page 36
Problem
Check
¥ Is the TV power turned on?
¥ Are the video cables properly connected?
¥ Is it the player in PAUSE mode?
¥ Is your TV’s video format (NSTC/PAL) set correctly?
¥ The disc revolves but no
picture appears.
¥ Picture shows interference Press the NTSC/PAL button once again to change the current selection.
¥ Is there any dirt on the disc, or is the disc damaged?
and quality is poor.
¥ It may not be possible to play some DVD discs due to poor manufacture.
¥ When a dark scene changes to a bright scene during playback, the
screen may flicker vertically. Some disturbance is normal.
Remote control unit does
not operate.
Audio or subtitle language
does not operate.
The Menu button is
pressed but the Menu
screen does not appear.
The screen ratio cannot
be changed.
The desired radio station
cannot be tuned in.
¥ Is the remote control being used within the appropriate distance
and angle of operation for the unit?
¥ Are there any obstacles between the remote control unit and the
remote control sensor?
¥ Are the batteries dead? Is it time to replace the batteries with new ones?
¥ The audio or subtitle language features does not operate with
DVDs that do not include multiple audio or subtitle languages.
¥ Is the remote control being used within the appropriate distance
and angle of operation for the unit?
¥ Are the batteries dead?
¥ Does tje disc have a Menu?
¥ You can play 16:9 wide DVDs in 16:9 WIDE mode or 4:3 LETTER
BOX mode or 4:3 PAN-SCAN mode; but 4:3 encoded DVDs only
show in 4:3 ratio. Refer to the DVD disc jacket and then select the
appropriate function.
¥ Is the antenna installed properly?
¥ When the antenna's input signal is weak, install an external FM
antenna in an area with good reception quality.
¥ The password for the
rating level has been
forgotten.
¥ The DVD player is
malfunctioning.
¥ While the player is in the stop mode, hold the Stop (
) button
down on the main unit for over 5 seconds."INITIAL" appears on the
display and all settings will return to the Factory Preset condition.
The RESET function erases all settings; do not use this
function unless necessary.
36
HT-DL100(GB)
11/6/02
14:33
Page 37
Cautions on Handling and Storing Discs
Small scratches on the disc may reduce sound and picture quality or cause breaks
in playback. Be especially careful not to scratch discs when handling them.
Handling and Storing Discs
When you get fingerprints or dirt on the
disc, clean it with a mild detergent diluted
in water and wipe with a soft cloth.
¥ When cleaning, wipe gently from the inside to the
outside of the disc.
Condensation may form if warm air comes into
contact with cold parts inside the player. When
condensation forms inside the player, the
player may not operate correctly. If this occurs,
remove the disc and let the player stand for 1
or 2 hours with the power on.
Disc Storage
Do not keep in direct
sunlight
Keep in a cool
ventilated area
¥ Do not allow the discs to become contaminated
with dirt.
¥ Do not load cracked discs or discs that are
scratched.
37
Keep in a clean
Protection jacket.
Store vertically.
HT-DL100(GB)
11/6/02
14:33
Page 38
Disc Type and Protection
Usable Discs
Disc Types
Marks
Recording
Types
Disc Size
12cm
DVD
VIDEO
Audio + Video
8cm
COMPACT
VIDEO-CD
DIGITAL VIDEO
DIGITAL AUDIO
Dolby Digital
disc
DTS Disc
12cm
74 min.
8cm
20 min.
12cm
74 min.
8cm
20 min.
Audio
DIGITAL
SOUND
DOLBY
D I G I T A L
Approx. 240 min. (Single-sided)
Approx. 480 min. (Double-sided)
Approx. 160 min. (Single-sided)
Approx. 160 min. (Double-sided)
Audio + Video
COMPACT
AUDIO-CD
Max. Playing Time
Digital Audio
disc
STEREO
Stereo disc
NTSC
PAL
NTSC broadcast PAL broadcast
system in USA, system in U.K,
Canada, Japan,
France,
South Korea, etc.. Germany, etc.
Do not use the following types of disc!
¥ LD, CDG, CD-I, CD-ROM and DVD-ROM cannot be played on this player.
¥ DVD discs purchased abroad may not play on this player.
If such discs are played, a "WRONG REGION CODE" message appears on the TV screen.
Copy Protection
¥ Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copyprotected DVD discs.
¥ This product incorporates copyright protection technology that is protected by methods claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
38
HT-DL100(GB)
11/6/02
14:33
Page 39
Specification
HT-DL100
G
E
N
E
R
A
L
T
U
F
N
M
E
R
T
U
A N
M E
R
Power Supply
120V, 60Hz
Power Consumption
120W
Weight
6.5Kg
Dimensions
W 370mm x D 300mm x H 80mm
Operating Temperature Range
+5°C~+35°C
Operating Humidity Range
10%~75%
Receiving Frequency
87.5~108MHz
Usable Sensitivity
10dB
S/N Ratio
60dB
Distortion
0.5%
Channel Separation
28dB
Receiving Frequency
Usable Sensitivity
54dB
S/N Ratio
40dB
Distortion
2%
VIDEO
V
I
D
E
O
O
U
T
P
U
T
A
M
P
L
I
F
I
E
R
39
522~1611KHz
1.0Vp-p(75Ω load)
Y:1.0Vp-p(75Ω load)
Component Video
Pr:0.70Vp-p(75Ω load)
Pb:0.70Vp-p(75Ω load)
Luminance Signal: 1.0Vp-p(75Ω load)
S-VIDEO
Color Signal: 0.286Vp-p(75Ω load)
Front speaker output
40W x 2(6Ω), Distortion 10%
Center speaker output
40W(6Ω), Distortion 10%
Rear speaker output
40W x 2(6Ω), Distortion 10%
Subwoofer speaker output
70W(3Ω), Distortion 10%
Frequency range
20Hz~25KHz
S/N Ratio
75dB
Channel separation
50dB
Input sensitivity
(AUX)500mV
HT-DL100(GB)
11/6/02
14:33
Page 40
Speaker system
S
P
E
A
K
E
R
5.1ch speaker system
Front/Center/Rear speaker
Subwoofer speaker
Impedance
6Ω x 5
3Ω
Frequency range
150Hz~18KHz
45Hz~250Hz
Output sound pressure level
87dB/W/M
86dB/W/M
Rated input
40W
70W
80W
140W
Maximum input
Dimensions
Weights
Front/Rear
103mm x 150mm x 120mm
Center
197mmx 103mmx 120mm
Front/Rear
0.73Kg
Center
0.80Kg
250mm x 403mm x 335mm
6.8Kg
40
HT-DL100(GB)
11/6/02
14:33
Page 41
Reference
Note on Terminology
ANGLE
CHAPTER
NUMBER
Recorded onto some DVD discs are scenes which have been simultaneously shot from a number
of different angles (the same scene is shot from the front, from the left , from the right , etc.). With
such discs, the Angle button can be used to change the angle of view for specific scenes.
These numbers are recorded on DVD discs. A Title is subdivided into many
sections, each of which is numbered, and specific parts of the video can be
searched quickly using these numbers.
DVD
A high-density optical disc on which high-quality pictures and sound have been recorded by means of digital
signals. Incorporating a new video compression technology (MPEG-2) and high-density recording technology,
a DVD disc comprises two 0.6 mm thick discs bonded together.
PCM
An acronym for Pulse Code Modulation - another name for digital audio.
PBC
(PLAYBACK
CONTROL)
REGION NUMBER
This is recorded on a video CD (version 2.0). Selected scenes or information can
be chosen from the menu displayed on the TV monitor.
Both the DVD player and DVD discs are encoded with a region number. If the
region number on the DVD disc does not correspond to the region number of
the DVD player, the player cannot play the disc.
SUBTITLES
Translated appearing at the bottom of the screen. A DVD disc can contain up to
32 subtitle languages.
TITLE NUMBER
These numbers are recorded on DVD discs. When a disc contains two or more
movies, these movies are numbered as Title 1, Title 2, etc.
TRACK NUMBER
VIDEO CD
These numbers are assigned to the tracks which are recorded on video and
audio CDs. They enable specific tracks to be located quickly.
Coutains recordings of pictures and sound whose quality is roughly comparable
to that of video tape.
This player also supports video CDs with playback control (version 2.0).
You can enjoy 5.1 (or 6) channels of high fidelity digital sound from various
digital input sources such as laser discs, DVD, CD etc.
DTS provides a realistic, clear surround sound that has not previously been
available from conventional surround sound.
DOLBY
D I G I T A L
PRO LOGIC
41
5.1 (or 6) Channel Digital Surround sound reproduced from DVDs and LDs
recorded as a digital signals (with
disc marking). With better sound quality,
dynamic range, and directionality than the traditional Dolby surround technology,
you can enjoy the dynamic realistic sound.
DOLBY
D I G I T A L
A 4 channel analog sound reproduced from a program source such as a videotape or
PRO LOGIC mark. You can enjoy a more realistic, robust sound
LP with the
unavailable from regular stereo sources.
DOLBY
HT-DL100(-Cover(GB)
11/6/02
14:35
Page 1
AH68-00988B