Samsung DV80F5E5HGW 8kg Front Load Dryer with Heat Pump technology User Manual

DV9 Series
DV8 Series
DV7 Series
Heat Pump Dryer
user manual
This manual is made with 100% recycled paper.
imagine the possibilities
Thank you for purchasing this Samsung product.
DV90F5E6HGW-03297J-06_EN_150706.indd 1
2015-07-06
1:07:50
contents
SAFETY INFORMATION
3
What you need to know about Safety
Instructions
Important safety symbols and precautions
INSTALLING YOUR DRYER
10
10
11
11
11
11
12
12
12
13
13
14
14
16
17
18
Unpacking your dryer and Installing guide
See Dryer Exterior
Check before installing
Before using the product
Important to installer
Location considerations
Alcove or closet installation
Electrical requirements
Grounding
Installation side by side
Final installation checklist
Draining water without using the water tank
Connecting the drain hose
Installation stacking
Door Reversal
Environment
OPERATING INSTRUCTIONS, TIPS
19
22
22
23
24
25
25
Overview of the control panel
Child lock
Delay End
Smart Check
Rack Dry (DV8 Series Only)
Load the dryer properly
Getting started
26
26
26
26
27
27
28
Clean the heat exchange
Control Panel
Stainless Steel Tumbler
Dryer Exterior
Dumping condensed water ( )
Cleaning the filter case ( )
Cleaning the Heat Exchanger Filter (
29
Special laundry tips
30
32
Check these points if your dryer…
Information codes
3
10
19
CARE AND CLEANING
26
SPECIAL LAUNDRY TIPS
29
30
33
TROUBLESHOOTING
APPENDIX
3
33
34
34
35
35
)
Fabric care chart
Protecting the environment
Specifications
Cycle chart
Consumption data
English - 2
DV90F5E6HGW-03297J-06_EN_150706.indd Sec9:2
2015-07-06
1:07:53
safety information
Congratulations on your new Samsung Dryer. This manual contains important
information on the installation, use, and care of your appliance. Please take the time
to read this manual to take full advantage of your dryer’s many benefits and features.
•
•
•
SAFETY INFORMATION
WARNING - Risk of Fire
Clothes dryer installation must be performed by a qualified technician.
Install the clothes dryer according to the manufacturer’s instructions and local codes.
To reduce the risk of severe injury or death, follow all installation instructions.
WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS
Warnings and Important Safety Instructions in this manual do not cover all possible conditions and
situations that may occur. It is your responsibility to use common sense, caution, and care when installing,
maintaining, or operating your dryer.
Always contact your manufacturer about problems or conditions you do not understand.
IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS
WARNING
Hazards or unsafe practices that may result in severe personal injury or
death and/or property damage.
CAUTION
Hazards or unsafe practices that may result in minor personal injury or
property damage.
CAUTION
To reduce the risk of fire, explosion, electric shock, or personal injury when
using your tumble dryer, follow these basic safety precautions:
To reduce the risk of fire or explosion, follow these basic precautions.
CAUTION
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions explicity.
Unplug the power plug from the wall socket.
Make sure the machine is grounded to prevent electric shock.
Call the service center for help.
Note
Read operator’s manual
These warning icons are here to prevent injury to you and others.
Please follow them explicitly.
After reading this section, keep it in a safe place for future reference.
Read all instructions before using the appliance.
English - 3
DV90F5E6HGW-03297J-06_EN_150706.indd Sec1:3
2015-07-06
1:07:53
safety information
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow
basic precautions, including the following:
Do not let children (or pets) play in or on your product. The product door does not
open easily from the inside and children may be seriously injured if trapped inside.
This appliance is not to be used by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
For use in Europe: This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
This appliance should be positioned so that the power plug, the water supply
taps, and the drain pipes are accessible.
For appliances with ventilation openings in the base, that a carpet must not
obstruct the openings.
The new hose-sets supplied with the appliance are to be used and that old hosesets should not be reused.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal
cut-out, this appliance must not be supplied through an external switching device,
such as a timer, or connected to a circuit that is regularly switched on and off by
the utility.
The tumble dryer is not to be used if industrial chemicals have been used for
cleaning.
The lint trap has to be cleaned frequently, if applicable.
Lint must not to be allowed to accumulate around the tumble dryer. (not applicable
for appliances intended to be vented to the exterior of the building)
Adequate ventilation has to be provided to avoid the back flow of gases into the
room from appliances burning other fuels, including open fires.
English - 4
DV90F5E6HGW-03297J-06_EN_150706.indd Sec1:4
2015-07-06
1:07:53
CAUTION
To minimize the risk of fire in a tumble dryer, the following should be observed:
Items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be
placed in a tumble dryer. Oil-affected items can ignite spontaneously, especially when exposed to heat sources
such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates
heat. If the heat cannot escape, the items can become hot enough to catch fire. Piling, stacking or storing oilaffected items can prevent heat from escaping and so create a fire hazard. If it is unavoidable that fabrics that
contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer
they should first be washed in hot water with extra detergent – this will reduce, but not eliminate, the hazard. The
‘cool down’ cycle of tumble dryers should be used to reduce the temperature of the items. They should not be
removed from the tumble dryer or piled or stacked while hot.
Items that have been previously cleaned in, washed in, soaked in or spotted with petrol/gasoline, dry-cleaning
solvents or other flammable or explosive substances should not be placed in a tumble dryer. Highly flammable
substances commonly used in domestic environments include acetone, denatured alcohol, petrol/gasoline,
kerosene, spot removers(some brands), turpentine, waxes and wax removers.
Items containing foam rubber(also known as latex foam) or similarly textured rubber. Like materials should not be
dried in a tumble dryer on a heat setting. Foam rubber materials can, when heated, produce fire by spontaneous
combustion.
Fabric softeners or similar products should not be used in a tumble dryer to eliminate the effects of static electricity
unless this practice is specifically recommended by the manufacturer of the fabric softener or product.
English - 5
DV90F5E6HGW-03297J-06_EN_150706.indd Sec1:5
2015-07-06
1:07:53
SAFETY INFORMATION
Do not dry unwashed items in the tumble dryer.
Items that have been soiled with substances such as cooking oil, acetone, alcohol,
petrol, kerosene, spot removers, turpentine, waxes and wax removers should be
washed in hot water with an extra amount of detergent before being dried in the
tumble dryer.
Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not be
dried in the tumble dryer.
Fabric softeners, or similar products, should be used as specified by the fabric
softener instructions.
The final part of a tumble dryer cycle occurs without heat (cool down cycle) to
ensure that the items are left at a temperature that ensures that the items will not
be damaged.
Remove all objects from pockets such as lighters and matches.
WARNING: Never stop a tumble dryer before the end of the drying cycle unless
all items are quickly removed and spread out so that the heat is dissipated.
Exhaust air must not be discharged into a flue which is used for exhausting fumes
from appliances burning gas or other fuels.
The appliance must not be installed behind a lockable door, a sliding door or a
door with a hinge on the opposite side to that of the tumble dryer, in such a way
that a full opening of the tumble dryer door is restricted.
For use in Europe: Children of less than 3 years should be kept away unless
continuously supervised.
safety information
Undergarments that contain metal reinforcements should not be placed in a tumble dryer. Damage to the tumble
dryer can result if metal reinforcements come loose during drying. When available a drying rack could be used for
such items.
Plastic articles such as shower caps or babies’ waterproof napkin covers should not be placed in a tumble dryer.
Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and rubber-coated tennis shoes
should not be placed in a tumble dryer.
Do not dry unwashed items in the tumble dryer(or washing machine drying mode,etc).
WARNING
Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, Kerosene, spot
removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent
before being dried in the tumble dryer.
Items such as foam rubber(latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or
pillows fitted with foam rubber pads should not be dried in the tumble dryer.
Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.
The final part of a tumble dryer cycle occurs without heat(cool down cycle) to ensure that the items are left at a
temperature that ensures that the items will not be damaged.
Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer.
The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot
escape, the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent
heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care
products be placed in a tumble dryer they should first be washed in hot water with extra detergent - this will
reduce, but not eliminate, the hazard.
CAUTION
Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out
so that the heat is dissipated.
Remove all objects from pockets such as lighters and matches.
WARNING
SEVERE WARNING SIGNS FOR INSTALLATION
The installation of this appliance must be performed by a qualified technician or service
company.
- Failure to do so may result in electric shock, fire, an explosion, problems with the product, or
injury.
Plug the power cord into an AC 220~240 V / 50 Hz wall socket or higher and use the socket for
this appliance only. In addition, do not use an extension cord.
- Sharing a wall socket with other appliances using a power strip or extending the power cord
may result in electric shock or fire.
- Ensure that the power voltage, frequency and current are the same as those of the product
specifications. Failure to do so may result in electric shock or fire. Failure Plug the power plug
into the wall socket firmly.
Remove all foreign substances such as dust or water from the power plug terminals and contact
points using a dry cloth on a regular basis.
- Unplug the power plug and clean it with a dry cloth.
- Failure to do so may result in electric shock or fire.
Keep all packaging materials well out of the reach of children, as packaging materials can be
dangerous to children.
- If a child places a bag over its head, it may result in suffocation.
English - 6
DV90F5E6HGW-03297J-06_EN_150706.indd Sec1:6
2015-07-06
1:07:53
Do not use a damaged power plug, damaged power cord or loose wall socket.
- This may result in electric shock or fire.
If the plug (power supply cord) is damaged, it must be replaced by the manufacturer or its
service agent or a similar qualified technician in order to avoid a hazard.
This appliance should be positioned to be accessible to the power plug after installation.
Do not pull or excessively bend the power cord.
Do not twist or tie the power cord.
Do not hook the power cord over a metal object, place a heavy object on the power cord, insert
the power cord between objects, or push the power cord into the space behind the appliance.
- This may result in electric shock or fire.
Do not pull the power cord, when unplugging the power plug.
- Unplug the power plug by holding the plug.
- Failure to do so may result in electric shock or fire.
This appliance must be properly grounded. Never plug the power cord into a receptacle that
is not grounded adequately and in accordance with local and national codes. See installation
instructions for grounding this appliance.
Install this appliance in a location with solid, level floor.
- Failing to do so may result in abnormal vibrations, noise or problems with the product.
Since an ingredient in hair spray may degrade the hydrophile property of the heat exchanger
so that dew may appear on the outer surface of the appliance when the cooling operation is
running, do not install the appliance in a beauty salon.
WARNING
SEVERE WARNING SIGNS FOR USING
Do not let children or pets on or into the product. In addition, when disposing of this product,
disassemble the door lock (lever).
- This may result in children falling and injuring themselves.
- If children become locked in the product, there is a danger of suffocation.
Do not try to access the inside of the product when the drum is rotating.
Do not sit on the product or lean against the door.
- This may result in the product turning over and resulting in injury.
Dry the laundry only after it was spun by an appropriate washing machine.
Do not dry unwashed items in the tumble dryer.
Do not drink the condensed water.
Never stop a tumble dryer before the end of the drying cycle unless all items are quickly
removed and spread out so that the heat is dissipated.
Do not dry laundry contaminated by inflammable materials such as gasoline, kerosene, benzene,
thinner, alcohol, etc.
- This may result in electric shock, fire or explosion.
Do not let pets chew or play with the dryer.
- This may result in electric shock or injury.
When disposing of the product, separate the door and the power cord before disposing of the
product.
- Failing to do so may result in damage to the power code or an injury.
English - 7
DV90F5E6HGW-03297J-06_EN_150706.indd Sec1:7
2015-07-06
1:07:53
SAFETY INFORMATION
This appliance must be properly grounded.
Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.
- This may result in electric shock, fire, an explosion, or problems with the product
- Never plug the power cord into a socket that is not grounded correctly and make sure that it
is in accordance with local and national codes.
Do not install or keep the product exposed to the outdoor elements.
safety information
Do not touch the power plug with wet hands.
- This may result in electric shock.
When gas (city gas, propane gas, LP gas) leaks, do not touch this appliance or the power cord,
ventilate immediately.
- At this time, do not use the ventilating fan.
- A spark may cause an explosion or fire.
- Oil-affected items can ignite spontaneously, especially when exposed to heat sources such
as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil.
Oxidation creates heat. If the heat cannot escape, the items can become hot enough to
catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping and so
create a fire hazard.
- If it is unavoidable that fabrics that contain vegetable or cooking oil or have
beencontaminated by hair care products be placed in a tumble dryer they should first be
washed in hot water with extra detergent - this will reduce, but not eliminate, the hazard.
- Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol,
kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot
water with an extra amount of detergent before being dried in the tumble dryer.
- Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed
articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble
dryer.
- Fabric softeners, or similar products, should be used as specified by the fabric softener
instructions.
- The final part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure that the
items are left at a temperature that ensures that the items will not be damaged.
- Remove all objects from pockets such as lighters and matches.
Do not repair, replace, or attempt to service any part of the appliance unless specifically
recommended in the user-repair instructions. You must also have the skills necessary to service
this appliance.
Do not attempt to repair, disassemble, or modify the appliance yourself.
- Do not use any fuse(such as cooper, steel wire, etc.) other than the standard fuse.
- When repairing or reinstalling the appliance is required, contact your nearest service center.
- Failure to do so may result in electric shock, fire, problems with the product, or injury.
The product you have purchased is designed for domestic use only.
The use for business purposes qualifies as product misuse. In this case, the product will not be
covered by the standard warranty provided by Samsung and no responsibility can be attributed
to Samsung for malfunctions or damages resulting from such misuse.
If the product generates strange noise, smells of something burning, or generates smoke,
immediately cut-off the power and contact the service center.
- Otherwise, it may cause an electric shock or fire as a result.
CAUTION
CAUTION SIGNS FOR USING
Do not stand on top of the appliance or place objects (such as laundry, lighted candles, lighted
cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
- This may result in electric shock, fire, problems with the product, or injury.
Do not touch the glass door and inside of the drum during or just after drying as it is hot.
- This may result in burns.
Do not press the buttons using sharp objects such as pins, knifes, fingernails, etc.
- This may result in electric shock or injury.
Do not dry laundry containing forming rubber (latex) or similar rubber textures.
- If forming rubber is heated, it may start a fire.
English - 8
DV90F5E6HGW-03297J-06_EN_150706.indd Sec1:8
2015-07-06
1:07:53
Recommend against using drying sheets to reduce static electricity as this could lead to damage
to your laundry and also potential damage to the appliance.
- This may result in damage to the laundry.
Do not use the dryer near dangerous powders such as coal dust, wheat flour, etc.
- This may result in electric shock, fire or an explosion.
Do not place inflammable materials near the product.
- This may result in toxic gases from the product, damage to parts, electric shock, fire or an
explosion.
- The appliance should not be placed behind lockable doors etc.
Do not touch the rear side of the appliance during or immediately after drying is complete.
- The appliance remains hot and may cause burns.
Contains fluorinated greenhouse gases covered by the Kyoto Protocol.
Hermetically sealed system.
Do not vent gases into the atmosphere.
Refrigerant (Type): R-134a (GWP = 1430)
Refrigerant (Charging): 0.4 kg, 572 kgCO2e
WARNING
SEVERE WARNING SIGNS FOR CLEANING
Do not clean the appliance by spraying water directly onto it.
Do not use benzene, thinner or alcohol to clean the appliance.
- This may result in discolouration, deformation, damage, electric shock or fire.
Before cleaning or performing maintenance, unplug the appliance from the wall socket.
- Failure to do so may result in electric shock or fire.
Clean the filter case before and after using the dryer.
Clean the inside of the product on a regular basis by asking an authorized service engineer.
Clean the Heat Exchanger with a soft brush or vacuum cleaner once a month, Do not touch the
heat exchanger with your hand. Otherwise, it may cause an injury.
The interior of the dryer should be cleaned periodically by qualified service personnel.
English - 9
DV90F5E6HGW-03297J-06_EN_150706.indd Sec1:9
2015-07-06
1:07:53
SAFETY INFORMATION
Do not dry laundry contaminated by vegetable oil or cooking oil as a large amount of the oil will
not be removed when washing the laundry. In addition, use the Cool Down cycle so that the
laundry is not heated.
- The oxidization heat of the oil may start a fire.
Make sure that the pockets of all clothing to be dryed are empty.
- Hard, sharp objects, such as coins, safety pins, nails, screws, or stones can cause extensive
damage to the appliance.
Do not dry clothing with large buckles, buttons, or other heavy metal (zippers, hooks and
eyelets, button-up covers).
If necessary, use the laundry net for small and lightweight laundry such as fabric tie belt , apron
strings, and underwire bras which can dissolve or break during a cycle.
installing your dryer
UNPACKING YOUR DRYER AND INSTALLING GUIDE
Hire a professional to install this dryer properly. If there is a service call performed as a result of poor setup,
adjustment, and connection, it is considered the responsibility of the installer. It is recommended that a
professional is called to install this appliance, especially for more difficult installations involving draining to the
mains water supply or product stacking. If problems of installation result in a service visit to fix a fault, this is
typically considered to be the responsibility of the installer.
Make sure you have everything necessary for proper installation (AC 220~240V/50Hz).
A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements (See page 11).
SEE DRYER EXTERIOR
Cover Top
Control panel
Water tank
Door
Filter case
Levelling feet
Parts
Hose guide
Cable tie
Hose
connector
Long drain hose (2m)
Manual
book
Rack Dry
(8 Series)
English - 10
DV90F5E6HGW-03297J-06_EN_150706.indd Sec3:10
2015-07-06
1:07:53
CHECK BEFORE INSTALLING
•
•
•
INSTALLING YOUR DRYER
•
•
•
•
•
Do not plug the power cord into the wall outlet before completing the dryer installation.
Check the appearance of the product for any damaged parts before starting the product installation.
If there are any parts that appear to be damaged, please contact your nearest Samsung Customer
Service Center.
When moving the product, do not move the product by yourself.
Take care of the edges of the dryer as they can be sharp.
Do not install the dryer in a location exposed to frost. Cold water may damage the product.
Use the product indoors only.
Do not place the dryer on one side when lifting it, and do not move the dryer in such a way that the
internal parts shake. This may result in damage to the internal parts of the product.
BEFORE USING THE PRODUCT
•
•
•
•
•
•
Check if there are any accessories remaining inside the drum.
Plug in the power cord just before operating the product.
Do not block the air inlet hole of the cooling grill at the front of the dryer.
Do not place inflammable objects near the dryer and keep the surroundings clean.
Keep the dryer level with the ground.
Do not remove the adjustable levelling feet of the dryer. They are necessary to keep the product level
with the ground.
IMPORTANT TO INSTALLER
Please read the following instructions carefully before installing the dryer. These instructions should be kept
for future reference.
WARNING
REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES TO AVOID THE DANGER OF A CHILD
SUFFOCATING.
LOCATION CONSIDERATIONS
Because a condensing type has been adopted, which condenses and processes air inside the dryer,
external ventilation is not required.
Therefore, The dryer can be installed and used in any location where the temperature is between 5 and 35
degrees centigrade, unlike a conventional dryer that requires an external exhaust system.
English - 11
DV90F5E6HGW-03297J-06_EN_150706.indd Sec3:11
2015-07-06
1:07:53
installing your dryer
ALCOVE OR CLOSET INSTALLATION
To operate safely and properly, your new Dryer requires minimum clearances of:
Sides – 25 mm
Rear – 51 mm
Top – 25 mm
Front – 470 mm
If both the washing machine and a dryer are installed together, the front of the alcove or closet must have at
least 465 mm unobstructed air opening.
ELECTRICAL REQUIREMENTS
Electrical Requirements is AC 220~240 V / 50 Hz.
•
WARNING
•
Improper connection of the equipment grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is
properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet,
have a proper outlet installed by a qualified electrician.
To prevent unnecessary risk of fire, electrical shock, or personal injury, all wiring and grounding
must be done in accordance with local codes, or in the absence of local codes, It is your
responsibility to provide adequate electrical services for your dryer.
GROUNDING
Your dryer must be grounded. If your dryer malfunctions or breaks down, grounding will reduce the risk of
electric shock by providing a path of least resistance for the electric current.
Your dryer comes with a power cord having a three-prong grounding plug for use in a properly installed and
grounded outlet.
Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.
Improperly connecting the equipment-grounding conductor can result electrical shock.
Check with a qualified electrician or serviceman if you are unsure if the dryer is properly grounded. Do
not modify the plug provided with the dryer. If it does not fit the outlet, have a proper outlet installed by a
qualified electrician.
WARNING
If the product is not grounded, there is a danger of fire or electric shock.
English - 12
DV90F5E6HGW-03297J-06_EN_150706.indd Sec3:12
2015-07-06
1:07:53
INSTALLATION SIDE BY SIDE
For proper installation, we recommend that you hire a professional. To install:
1. Move your dryer to an appropriate location for installation. Consider
installing the dryer and washer side-by-side. Lay two of the carton
cushion-tops on the floor. Tip your dryer on its side so it will lay across
both cushion-tops.
2. Set your dryer back in an upright position.
3. To ensure that the dryer provides optimal drying performance, it must
be level. To minimize vibration, noise, and unwanted movement,the
floor must be a perfectly level, solid surface.
Level
INSTALLING YOUR DRYER
To set the dryer to the same height as the washer, fully retract the
levelling feet by turning them counterclockwise, then loosen the legs
by turning them clockwise
Levelling feet
Retract fully
Then loosen
Adjust the levelling feet only as much as necessary to level the dryer.Extending the levelling feet more
than necessary can cause the dryer to vibrate.
4. Review Electrical Requirements section (See page 11).
BEFORE OPERATING OR TESTING.
5. With a level, check your dryer and make necessary adjustments to the levelling legs.
6. Plug in your dryer, and check operation by using the checklist below.
FINAL INSTALLATION CHECKLIST




Dryer is plugged into electrical outlet and is properly grounded.
Dryer is leveled and is sitting firmly on the floor.
Start your dryer to confirm that it runs, heats, and shuts off.
Finally, check if the HE error occurs when after running the Time Dry cycle for 20 minutes.
English - 13
DV90F5E6HGW-03297J-06_EN_150706.indd Sec3:13
2015-07-06
1:07:53
installing your dryer
DRAINING WATER WITHOUT USING THE WATER TANK
You can use the dryer without using the water tank by following the procedures below.
Install the drain hose so that water can be drained well.
- Otherwise, the water may overflow and it may cause damage to the properties.
CONNECTING THE DRAIN HOSE
The Dryer can pump the condensed water outside of the DRYER directly
with dain hose provide.
The procedures to connect the drain hose are as follows.
1. Disconnect the drain hose
A
.
A
2. Connect the drain hose
A
to the other hole.
A
3. Connect accessory hose(long drain hose)
B
to the hole
next to the hole that is connected to drain hose A .
• Because the dryer’s drain pump can only pump up
the drain water to a 90 cm height, when you connect
CAUTION
•
B
the drain hose B to the drain point, make sure that
the height of drain point does not exceed 90 cm.
A drainage error may occur if the drain point exceeds
90 cm. If a drainage error occurs, the control panel
displays an error code.
After connecting the drain hose, you can directly drain the condensed water via the
drain-outlet through the connected drain hose or through the washstand or the drainoutlet of the washstand.
English - 14
DV90F5E6HGW-03297J-06_EN_150706.indd Sec3:14
2015-07-06
1:07:54
Connecting the drain hose
CAUTION
The end of the drain hose can be positioned in three ways:
1. Over the edge of a wash basin: The drain hose must be placed lower than 90cm. If the end
of the drain hose needs to be placed above the ground, we recommend a height of 60cm ~
90cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the
guide to the wall with a hook or to the tap with a piece of string to prevent the drain hose
from moving.
90 cm
Drain hose
Hose guide
Cable Tie
2. Assemble the drain hose and the hose guide and fix them with the cable-tie.
3. You can drain the condensed water by connecting the accessory hose (long drain hose) to
the drain-outlet directly.
Connecting the direct-hose
You can immediately drain the condensed water that comes out while drying, by connecting the
drain hose to the tap.
1. Assemble the hose connector and the hose.
CAUTION
Since there is a danger of water leaking from the hose
connecter and accessory hose, make sure that they are
connected firmly.
Hose Connecter
2. Connect the end of the hose to the tap.
English - 15
DV90F5E6HGW-03297J-06_EN_150706.indd Sec3:15
2015-07-06
1:07:54
INSTALLING YOUR DRYER
Do not extend the drain hose.
- Since water may leak from the connected part, be sure to one long drain hose instead of
connecting short ones. If you cannot help connecting more than one hose, be sure to seal
the connected parts with silicone sealant. (Do not use the electric insulating tape for sealing.)
installing your dryer
INSTALLATION STACKING
In case of purchasing the additional stacking kit, contact our Samsung service center or local
distributers. [Part no. SK-DH / SK-DA / SKK-DF]
The stacking kit differs depending on the model.
Only use the product in 1 hour after installing the stacking kit by tilting the product so that the product
can run after the oil in the compressor becomes stable.
1. Carefully lay the dryer on its side. Use the packing material so
you don’t scratch the finish on the dryer.
2. Install rubber pads to dryer base.
• Locate the 4 rubber pads in the parts package. Insert the
rubber pads into the holes at the bottom of the levelling legs.
• Purchase the stacking-kit package additionally.
3. Set the dryer upright.
CAUTION
The stacking kit can only be installed for Samsung family products.
4. Install bracket to dryer.
• Remove washer top cap screw from the rear left. Align left
bracket holes with top cap screw hole on rear left of the unit
and replace screw.
Leave screw loose so dryer hole alignment will be easier.
• Repeat the above step with the right side.
Bracket-Stacking
5. Install dryer and bracket on washer
Screw
• Lift the dryer on top of the washer. Protect the washer
control panel with cardboard or other protection. Be sure to
WARNING
lift the dryer high enough to clear the washer control panel.
Personal Injury. More than two people are recommended
to lift the dryer into position because of its weight and size.
Failure to do so could result in injury.
• Align the holes in the bracket with the holes in the back of the dryer.Using a Phillips
screwdriver, attach the M4x12 tapping screws.
• Tighten the washer bracket screws ; then tighten all stacking kit screws.
6. Finalise the installation
• Refer to the washer Installation Instructions to complete
the washer installation.
WARNING
• Refer to the dryer Installation Instructions to complete the
dryer installation.
• Carefully slide or walk the stacked washer and dryer
into place. Use felt pads or other sliding device to assist
moving and to protect flooring.
Do not push on the dryer once installed to top of the
washer. Pushing on the dryer may result in pinched fingers.
Dryer
Washer
English - 16
DV90F5E6HGW-03297J-06_EN_150706.indd Sec3:16
2015-07-06
1:07:54
DOOR REVERSAL
Frame-Front
Assy-Door
1. Unplug the power cord.
2. Remove the two screws from the door-hinge.
3. Lift the door to separate it.
Hinge-Door
4. Remove the 16 screws.
Disassemble the air seal and remove the 6 screws (3 flat
head screws at the top and 3 round head screws at the
bottom).
(Only for Crystal Gloss door models)
Crystal Gloss Door
5. After removing the screw, rotate the Assy hinge door,
the handle door by 180° as shown in the figure.
• Work carefully so that the door-seal is not removed.
CAUTION
Door-Glass
Handle Door
Crystal Gloss Door
Assy hinge door
6. Fasten the 16 screws in the correct positions.
Fasten the 6 screws and replace the air seal.
(Only for Crystal Gloss door models)
7. Note that two of the screws have a different length from the others.
(Use the longer screws for the door-lever.)
8. Move the position of the screw at the back of the door-hinge.
English - 17
DV90F5E6HGW-03297J-06_EN_150706.indd Sec3:17
2015-07-06
1:07:54
INSTALLING YOUR DRYER
Depending on your requirements (installation location, space constraints), you can change the direction the
door opens.
This is done according to the customer’s needs. The qualified technician or customer can do this
WARNING themselves directly.
installing your dryer
9. Fasten the screw in the bottom hole.
10. Remove the two screws holding the front-frame at the left.
11. Remove the two screws holding the holder-lever at the left.
Holer-Lever
12. Now, move to the right side of the product and fasten the two screws
holding the front-frame and the two screws holding the lever-holder.
13. Align the door with the fixing holes.
14. Fasten the two screws holding the door-hinge.
Inside the drum
You can restore the direction the door opens by following the procedures above, if necessary.
ENVIRONMENT
Please dispose of the packaging materials for this product in an “environmentally friendly” manner.
For further detail, please contact your local area authority.
English - 18
DV90F5E6HGW-03297J-06_EN_150706.indd Sec3:18
2015-07-06
1:07:55
operating Instructions, tips
WARNING
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS before operating this appliance.
If the Anti Crease option is not selected, take out the laundry immediately after it is washed and dried.
Leaving the laundry inside the drum may produce wrinkles.
OPERATING INSTRUCTIONS, TIPS
OVERVIEW OF THE CONTROL PANEL
[DV9, DV8 Series]
2
1
3
4
5
6
7
8
9
10
11
10
11
[DV7 Series]
2
1
Digital Graphic
Display
1
3
4
5
9
Displays the remaining drying cycle time, all cycle information, and error
messages.
The display window shows the estimated time remaining in the cycle after you
have pressed the Start/Pause button. The estimated time remaining may
fluctuates as the cycle progresses.
The Drying light will illuminate and remain lit until the cycle is complete.
When your dryer is in the cool-down phase, the Cooling light will illuminate.
When your dryer is in the Anti Crease phase, the “Anti Crease light” will
illuminate.
When the cycle is complete, “End” will appear in the display panel until you
push the Start/Pause button or the Power button. If your dryer is paused
during a cycle, the indicators will light up until you press the Start/Pause
button.
English - 19
DV90F5E6HGW-03297J-06_EN_150706.indd Sec5:19
2015-07-06
1:07:55
operating Instructions, tips
2
3
Cycle Selector
cycle is selected
When you turn on your dryer, the [Cotton] Cupboard Dry
as default.
Turn the Cycle Selector to select the cycle you want.
Cotton - For averagely or lightly soiled cottons, bed linen, table linen,
underwear, towels, shirts, etc.
• Extra Dry - Use for heavy-duty fabrics or items that should be very dry.
• Cupboard Dry
- Use this cycle to dry loads such as cotton, underwear,
and linen (NOT appropriate for jeans).
• Iron Dry - Finishes the dry cycle in a moist state appropriate for Ironing.
Synthetics - For averagely or lightly soiled blouses, shirts, etc., made of
polyester (diolen, trevira), polyamide (perlon, nylon) or other similar blends.
• Extra Dry - Use for heavy-duty fabrics or items that should be very dry.
• Cupboard Dry - Use this cycle to dry loads such as shirts, blouses, bed
linen and table linen. (NOT appropriate for jeans).
• Iron Dry - Finishes the dry cycle in a moist state appropriate for Ironing.
Quick Dry - 60 min is automatically set as the drying time.
Warm Air - For small items, pre-dried laundry and normal fabrics in
30 minutes. (DV9, DV8 Series)
Cool Air - For all fabrics to need freshing tumbles without heating.
Time Dry - Time Dry allows you to select the desired cycle time.
Turn the cycle selector dial to Time Dry, then press Time Button to set the
drying time. Press the Time button repeatedly to scroll through the time
settings. The drying time increase in every 30 minutes up to 150 minutes.
After drying the laundry with the normal airy dry cycle, and you feel that the
laundry has not dried completely, you can extend the drying time using the
Time Dry cycle.
After drying the laundry using a drying cycle, and you feel that the laundry has
not dried completely, you can extend the drying time using the Time Dry cycle.
Sports Wear - Use for light sportswear such as sweatsuit.
Outdoor - For water-proof items such as mountain clothing, skiwear and
sports wear. Fabrics include functional technology finishes and fibres such as
spandex, stretch, and micro-fibre. We recommend that you use this drying
cycle after you wash your laundry using the Outdoor Care cycle with your
washing machine. (DV9, DV8 Series)
Ultra Delicate - The Delicates cycle is designed For lingeries.
Wool - For machine washable and tumble dryable wool only.
For better drying results, turn the laundry inside out before drying it.
Overloading the dryer may not yield the same results. For the Max Load
of each drying course, refer to the Cycle Chart in the appendix
Drying Level
button
To select the dry level in the Cotton, Synthetics cycles, press the
Drying Level button. An indicator light will illuminate next to the dryness level
you selected.
Press the button repeatedly to scroll through the settings. Larger or bulkier
loads may require the icon “ or ” Dry setting for complete dryness.
the icon “ ” is designed to partially dry items. Use for items that lay flat or
hang to dry.
English - 20
DV90F5E6HGW-03297J-06_EN_150706.indd Sec5:20
2015-07-06
1:07:55
5
Anti Crease
button
Anti Crease provides approximately 120 minutes of intermittent tumbling
in unheated air at the end of the cycle to reduce wrinkling. Press the
Anti Crease button to activate this feature.
The indicator light above the pad will illuminate when Anti Crease is selected.
Dried laundry is prevented from becoming wrinkled by periodic drum rotations
after the completion of the drying course. (Even after “End” is displayed, the
drum rotates intermittently.)
6
Mixed Load Bell
button
This is an alarm that notifies the user when the average drying level is damp
dry (80 % dried) when the laundry contains various types of materials and
fabric.
If the corresponding condition is satisfied, the Mixed load bell LED blinks
Lamp button
Lights the dryer drum while the dryer is running. (DV9, DV8 Series)
It can be set while your dryer is not only running but also when it is
stopped. If you do not turn the Drum Light off within 5 minutes of turning
it on, it is automatically turned off.
8
Sound On/Off
button
The Sound On/Off function can be selected during all courses. When this
function is selected, sound is turned off for all courses. Even if the power is
turned on and off repeatedly, the setting is retained.
For DV7 Series model, press the Time and Anti Crease buttons at the
same time for 3 seconds.
9
Delay End
button
Press this button repeatedly to cycle through the available Delay End options.
(from 3 hours to 19 hours in one hour increments).
The hour displayed indicates the time when the dry cycle will be finished.
See page 21 for detail.
10
Start/Pause
button
Press to start a dry cycle. If the dryer is running, press it once and it will pause
the dryer. Press it again to restart the dry cycle.
11
Power button
Press once to turn your dryer on, press again to turn it off. If your dryer is left
on for more than 10 minutes without any buttons being touched, the power
automatically turns off.
4
7
OPERATING INSTRUCTIONS, TIPS
Time button
When using Time Dry, Warm Air, Cool Air cycles, time can be adjusted by
pressing the Time button.
30 min  60 min  90 min  120 min  150 min (120 min and 150 min time
options are not available for Warm Air and Cool Air cycles.)
Except the Time Dry, Quick Dry, Warm Air, Cool Air cycle, the time indicator
of manual is off because exact drying times are determined by fluctuating
humidity levels.
If you insert laundry into your dryer while it is extremely tangled immediately after your washer has
finished a wash or spin cycle, it may degrade the drying efficiency or cause the door to open.
We recommend that you disentangle your laundry appropriately before inserting it.
Each indicator on the graphic display means:
Drying in Progress
Drying Level 3 (Strong)
Cooling in Progress
Drying Level 2 (Normal)
Stop
Drying Level 1 (Gentle)
Anti Crease in Progress
Anti Crease
Filter Check
Heat Exchanger Filter Clean Alarm
Delay End
Sound On/Off
Dumping Condensed Water
Mixed Load Bell
Child Lock On/Off
Smart Check
English - 21
DV90F5E6HGW-03297J-06_EN_150706.indd Sec5:21
2015-07-06
1:07:55
operating Instructions, tips
CHILD LOCK
A function to prevent children from playing with your dryer.
Activating/Deactivating
If you want to activating/deactivating the Child Lock, press
both the Drying Level and Time buttons simultaneously for
3 seconds.
The “Child Lock ” will be lit when this feature is activated.
• When the power is turned on, the Child Lock function is
available.
• Once you set the Child Lock function, no button, except
for the Power button, will respond until you release the
Child Lock function.
• If the dryer is powered on again, the Child Lock function
stays on.
• When other buttons, except for the Power button, do
not respond, check the Child Lock indicator to see if the
function is on.
[DV9, DV8 Series]
[DV7 Series]
3 sec.
DELAY END
You can set the dryer to finish your drying cycle automatically at a later time, choosing a delay of between
3 to 19 hours (in 1 hour increments). The hour displayed indicates the time at which the dry will be finished.
1. Manually or automatically set your drying machine according to the type of laundry you are drying.
2. Press the Delay End button repeatedly until the required delay time is set. If the delay time is set, the
“Delay End” function becomes ON state.
3. Press the Start/Pause button. The “Delay End ” indicator will blink and the clock will begin counting
down until it reaches the set time.
4. To cancel a Delay End function, press the Power button and then turn the dryer on again.
English - 22
DV90F5E6HGW-03297J-06_EN_150706.indd Sec5:22
2015-07-06
1:07:56
SMART CHECK
This function enables you to check the status of the dryer using a smartphone.
Downloading the Samsung Smart Washer app
Download the Samsung Smart Washer app to your mobile phone from the Android market or
Apple App store and install it. You can easily find it by searching for “Samsung Smart Washer”.
Using the Smart Check function
1. Hold down the Anti Crease and Mixed Load Bell
buttons at the same time for 3 seconds when an error
occurs to run the Smart Check function. Alternatively, the
Smart Check function can be run if no button is pressed
after the dryer is turned on.
2. The LED segments on the display panel rotate for 2 or
3 seconds and the Smart Check code is displayed on the
dryer’s display panel.
[DV9, DV8 Series]
[DV7 Series]
3 sec.
3. Run the Samsung Smart Washer app on your smart phone and tap the Smart Check
button.
‘Smart Check’ may be changed to ‘Smart Care’ according to the language selection.
4. Focus your smart phone’s camera on the Smart Check code displayed on the dryer’s display
panel.
• If light from a light bulb, fluorescent bulb or lamp is reflected on the display panel of the dryer,
the smart phone may not be able to easily recognize the Smart Check code.
• If you hold the smart phone at a too wide angle relative to the front of the display panel, it
may not be able to recognize the error code. For best results, hold the smart phone so that
the front of the display panel and the smart phone are parallel or nearly parallel.
5. If it focuses correctly, the Smart Check code is automatically recognized, and the detailed
information of the status of your dryer, the error and the countermeasures are displayed on
your smart phone.
6. If the smart phone fails to recognize the Smart Check code more than twice, please enter the
Smart Check code displayed on your dryer’s display panel into the Samsung Smart Washer
app manually.
English - 23
DV90F5E6HGW-03297J-06_EN_150706.indd Sec5:23
2015-07-06
1:07:56
OPERATING INSTRUCTIONS, TIPS
The Smart Check function has been optimized for:
Galaxy & iPhone series (cannot be supported for some models)
operating Instructions, tips
RACK DRY (DV8 SERIES ONLY)
Installing the drying rack
1. Open the dryer door.
2. Position the drying rack in the tumbler, placing the front lip of the drying rack on the top of
the lint filter case.
3. Place the rear legs in the two recessed areas of the dryer’s back wall then push down the
middle of the drying rack to fix.
4. Place the items to be dried on the rack, leaving space between them so air can circulate.
5. Close the dryer door.
6. Press the Power button.
7. Select Time Dry by using the cycle selector dial, set the Time button.
• You can set the drying time up to 150 minutes. Select the time according to the moisture and
weight of the items. It may be necessary to reset the timer if a longer drying time is needed.
(When you dry laundry using the drying rack, using the Time Dry cycle is recommended.)
8. Press the Start/Pause button.
Rack dry
SUGGESTED ITEMS
REMARKS (MAX 1.5kg)
Washable sweaters
(block to shape and lay flat on
rack)
Stuffed toys
(cotton or polyester fiberfilled)
Stuffed toys
(foam or rubber-filled)
When drying the laundry using the Rack, fold and place
the clothes on the Rack to prevent the clothing from
becoming wrinkled.
Foam rubber pillows
Sneakers
WARNING
CAUTION
To dry sports shoes, place the shoes on the Rack so that
the soles of the shoes are facing downwards.
Drying foam rubber, plastic, or rubber on a heat setting may cause damage to the items
and lead to a fire hazard.
Since damage may result when drying shoes, use the Rack Dry course to dry shoes.
English - 24
DV90F5E6HGW-03297J-06_EN_150706.indd Sec5:24
2015-07-06
1:07:56
LOAD THE DRYER PROPERLY
•
•
•
•
•
•
OPERATING INSTRUCTIONS, TIPS
•
Place only one wash load in your dryer at a time.
Mixed loads of heavy and lightweight fabrics will dry differently, which may result in lightweight fabrics
being dry while heavy fabrics remain damp at the end of a drying cycle.
Add one or more similar items to your dryer when only one or two articles of clothing need drying.
This improves the tumbling action and drying efficiency.
Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some
fabrics.
Make sure to insert laundry that has been spun by an appropriate washing machine.
No unwashed textiles should be dried
Textiles which have been in contact with oil, alcohol, petrol etc. should not be dried.
GETTING STARTED
1.
2.
3.
4.
5.
6.
Load your dryer loosely – DO NOT overload.
Close the door.
Select the appropriate cycle and options for the load.
Press the Start/Pause button.
The dryer indicator light will illuminate.
The estimated cycle time will appear in the display.
The time may fluctuate to better indicate drying time remaining in the cycle.
•
•
•
When the cycle is complete and “End” will appear in the display.
Pressing Power cancels the cycle and stops your dryer.
The Drying, Cooling, and Anti Crease indicator lights will illuminate during those portions of the
cycle.
English - 25
DV90F5E6HGW-03297J-06_EN_150706.indd Sec5:25
2015-07-06
1:07:56
care and cleaning
WARNING
WARNING
Do not clean the dryer by directly spraying water onto the dryer. Do not clean the dryer with benzene,
thinner, alcohol, or acetone.
- Otherwise, it may cause discoloration, deformation, damage, electric shock or fire.
When cleaning the product, be sure to unplug the power cord.
During the drying cycle, the control panel or the door may accumulate moisture.
CLEAN THE HEAT EXCHANGE
Since the surface of the heat exchanger is sharp, clean it with a soft brush or vacuum cleaner.
(It is recommended to clean it at least once every month.)
CAUTION
Do not touch the heat exchanger with your hand. Otherwise, it may cause an injury.
CONTROL PANEL
Clean with a soft, damp clothes. Do not use abrasive substances.
Do not spray cleaners directly on the panel.
The control panel finish may be damaged by some laundry pre-treatment soil and stain remover products.
Apply such products away from your dryer and wipe up any spills or overspray immediately.
STAINLESS STEEL TUMBLER
To clean the stainless steel tumbler, use a damp cloth with a mild, non-abrasive cleaner suitable for stainless
steel surfaces.
Remove the cleaner residue and dry with a clean cloth.
DRYER EXTERIOR
The entire dryer has a high-gloss finish. Clean with a soft, damp cloth. Do not use abrasive substances.
Protect the surface from sharp objects as they may scratch or damage the finish.
Do not place any heavy or sharp objects or a detergent box on the dryer. Keep them on the purchased
pedestal or in a separate storage box.
English - 26
DV90F5E6HGW-03297J-06_EN_150706.indd Sec10:26
2015-07-06
1:07:57
DUMPING CONDENSED WATER (
)
1. Pull the water-tank forwards to separate it.
CAUTION
Water-Tank
2. Remove the condensed water inside the water-tank.
• Remove the condensed water in the tank after every
drying operation.
WARNING
Since there is a danger of water leaking if you do not
drain the water after using the product, make sure to
drain the water.
Drain hole
If you empty the water tank and press the Start button,
the Water Tank Full ( ) in the LED panel is turned off.
CLEANING THE FILTER CASE (
)
1. Open the door and remove the filter by pulling it upwards.
Filter case
2. Open and clean the filter case.
• Clean the filter case after the drying operation is
completed.
CAUTION
• Since the drying performance may be degraded and there is a danger of fire if you do not
clean the filter case after the specified period of use, clean the filter case at the specified
cleaning interval.
• Clean the filter case after every drying operation.
• If the surface of the filter is wet, use the filter after drying it completely.
English - 27
DV90F5E6HGW-03297J-06_EN_150706.indd Sec10:27
2015-07-06
1:07:57
CARE AND CLEANING
When removing the water tank from the product, hold the
water tank using both hands as it is heavy and take care
not to spill any water inside the tank. Otherwise, it may
cause an injury to your wrist.
care and cleaning
CLEANING THE HEAT EXCHANGER FILTER (
)
1. Use a key or coin to open the cover.
2. Unlock the fixer.
Fixer
3. Remove the Heat Exchanger Filter.
4. If the heat exchange filter is not cleaned regularly, a display
indicator will be turned on or blinked as a reminder.
If so, check the heat exchanger filter and clean it to make
sure that the filer is not blocked with lints.
• Remove the sponge from the filter assembly and clean
it by rubbing in running water. Dust off the mesh part
CAUTION
with soft brush. After cleaning with water, dry the Heat
Exchanger Filter thoroughly before reinserting it back.
• Clean the heat exchanger filter after every 2 cycle is
completed.
• When the indicator is turned on or blink, check the heat
exchanger and clean it to make sure that the filter is not
blocked with lints.
5. Clean it with a soft brush or vacuum cleaner.
(It is recommended to clean it at least once every month.)
CAUTION
Do not touch the heat exchanger with your hand.
Otherwise, it may cause an injury.
CAUTION
• When assembling the Heat Exchanger Filter after cleaning it, make sure to that the fixer
is set to the lock position.
English - 28
DV90F5E6HGW-03297J-06_EN_150706.indd Sec10:28
2015-07-06
1:07:57
special laundry tips
SPECIAL LAUNDRY TIPS
Please follow the care label or manufacturer’s instructions for drying special items. If care label instructions
are not available, use the following information as a guide.
Bedspreads & Comforters
•
Blankets
•
•
SPECIAL LAUNDRY TIPS
•
•
Follow the care label instructions or dry on the
Cotton (Cupboard Dry
) and High temperature.
Make sure the item is thoroughly dry before using or storing.
May require repositioning to ensure even drying.
Use Cotton (Cupboard Dry
) and dry only one blanket at a time
for best tumbling action.
Make sure the item is thoroughly dry before using or storing.
Cloth Nappies
•
Use the Cotton (Cupboard Dry
settings for soft,fluffy diapers.
Down–filled Items (jackets,
sleeping bags, comforters,
etc.)
•
Use the Cotton (Cupboard Dry
) and the Low or Low temperature
setting.
Adding a couple of dry towels shortens drying time and absorbs
moisture.
Foam Rubber (rug backs,
stuffed toys, shoulder pads,
etc.)
•
•
DO NOT dry on a heat setting. Use the Cool Air cycle (no heat).
WARNING – Drying a rubber item with heat may damage it or be a
fire hazard.
Pillows
•
•
Use the Cotton (Cupboard Dry
).
Add a couple of dry towels to help the tumbling action and to fluff the
item.
DO NOT dry kapok or foam pillows in dryer. Use the Cool Air cycle.
•
•
Plastics (shower curtains,
outdoor furniture covers,
etc.)
•
) and the High temperature
Use the Cool Air cycle or the Time Dry cycle and the Low or Low
temperature settings depending on the care label instructions.
THINGS TO AVOID :
• Fiberglass items (curtains, draperies, etc.).
• Woolens, unless recommended on the label.
• Vegetable or cooking oil-soaked items.
English - 29
DV90F5E6HGW-03297J-06_EN_150706.indd Sec8:29
2015-07-06
1:07:57
troubleshooting
CHECK THESE POINTS IF YOUR DRYER…
PROBLEM
SOLUTION
Doesn’t run.
•
•
•
•
•
•
Doesn’t heat.
•
•
•
•
Doesn’t dry.
•
•
•
•
•
•
•
•
Is noisy.
•
•
•
Dries unevenly.
•
•
Has an odour.
•
•
Shuts off before load is dry.
•
•
Make sure the door is latched shut.
Be sure the power cord is plugged into a live electrical outlet.
Check the home’s circuit breaker and fuses.
Press the Start/Pause button again if the door is opened during the
cycle.
Empty the water in the condensed water tank.
Clean the filter case.
Check the home’s circuit breaker and fuses.
Select a heat setting other than Cool Air.
Check the case filter and Heat Exchanger Filter and clean them if
necessary.
Dryer may have moved into the cool-down phase of the cycle.
Check all of the above, plus...
Do not overload. 1 wash load = 1 dryer load.
Sort heavy items from lightweight items.
Large, bulky items like blankets or comforters may require
repositioning to ensure even drying.
Check that the dryer is draining properly to extract adequate water
from the load.
Load may be too small to tumble properly. Add a few towels.
Clean the filter case.
Clean the Heat Exchanger Filter.
Check the load for objects such as coins, loose buttons, nails, etc.
Remove promptly.
Be sure the dryer is leveled properly as outlined in the installation
instruction.
It is normal for the dryer to hum due to the high velocity of air moving
through the dryer drum and fan.
Seams, pockets, and other similarly heavy areas may not be
completely dry when the rest of the load has reached the selected
dryness level. This is normal. Select the Extra Dry setting if desired.
If one heavy item is dried with a lightweight load, such as one towel
with sheets, it is possible that the heavy item will not be completely
dry when the rest of the load has reached the selected dryness level.
Sort heavy items from lightweight items for best drying results.
Household odors from painting, varnishing, strong cleaners, etc.
may enter the dryer with the surrounding room air. This is normal as
the dryer draws the air from the room, heats it, pulls it through the
tumbler, and exhausts it outside.
When these odors linger in the air, ventilate the room completely
before using the dryer.
Dryer load is too small. Add more items or a few towels and restart
the cycle.
Dryer load is too large. Remove some items and restart the dryer.
English - 30
DV90F5E6HGW-03297J-06_EN_150706.indd Sec6:30
2015-07-06
1:07:57
PROBLEM
SOLUTION
Lint on clothes.
•
•
•
Garments still wrinkled after •
Anti Crease.
•
Small loads of 1 to 4 items work best.
Load fewer garments.Load similar-type garments.
Odours remain in clothing
after Cool air.
Fabrics containing strong odors should be washed.
•
TROUBLESHOOTING
•
Make sure the case filter is cleaned before every load. With some
loads that produce high amounts of lint, it may be necessary to clean
the filter case during the cycle.
Some fabrics are lint producers (for example, a fuzzy white cotton
towel) and they should be dried separately from clothes that are lint
trappers (for example, a pair of black linen pants)
Divide larger loads into smaller loads for drying
Check pockets thoroughly before drying and drying clothes.
English - 31
DV90F5E6HGW-03297J-06_EN_150706.indd Sec6:31
2015-07-06
1:07:57
troubleshooting
INFORMATION CODES
Information codes may be displayed to help you better understand what is occurring with your Dryer.
ERROR DISPLAY
MEANING
SOLUTION
tE
Air temperature sensor error
Clean the filter case or heat exchanger filter.
If the problem continues call for service.
tE5
Compressor temperature sensor
error
Turn the power on after 2~3 minutes and
start again from the beginning.
dE
Running the dryer with door open
Close the door and then restart.
If the problem continues call for service.
HE
Compressor overheat
Call for service
2E
It occurs when low voltage is
detected.
Check if the power cord is plugged in. If
the problem continues, please contact the
service center.
5E
The water tank is full of water.
The drain pump is out of order.
Empty the water tank, turn the power on
again and start again from the beginning.
If the problem continues call for service.
For any codes not listed above, or if the suggested solution doesn’t fix the problem, call your Samsung
Service Centre or local Samsung dealer.
Do not let an unauthorized engineer disassemble or repair the product.
English - 32
DV90F5E6HGW-03297J-06_EN_150706.indd Sec6:32
2015-07-06
1:07:57
appendix
FABRIC CARE CHART
Wash Cycle
Special Instructions
Warning Symbols for
Laundering
Normal
Line Dry/ Hang to Dry
Do Not Wash
Permanent Press /
Wrinkle Resistant /
Wrinkle Control
Drip Dry
Do Not Wring
Gentle/Delicates
Dry Flat
Do Not Bleach
Hand Wash
Heat Setting
Do Not Tumble Dry
High
No Steam (added to
iron)
Hot
Medium
Do Not Iron
Warm
Low
Cold
Any Heat
Dry Clean
No Heat/Air
Do Not Dry Clean
Water Temperature**
Bleach
Any Bleach (when
needed)
Iron-Dry or Steam
Temperatures
Dryclean
Line Dry/ Hang to Dry
Only Non-Chlorine
(color-safe)
Bleach (when needed)
High
Drip Dry
Tumble Dry Cycle
Medium
Dry Flat
Normal
APPENDIX
The following symbols provide garment care direction. The Clothing care labels include symbols for drying,
bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency
among garment manufacturers of domestic and imported items. Follow care label directions to maximize
garment life and reduce laundering problems.
Low
Permanent Press/
Wrinkle Resistant/
Wrinkle Control
Gentle/ Delicates
** The dot symbols represent appropriate wash water temperatures for various items. The temperature
range for Hot is 41 – 52 °C, for Warm 29 – 41 °C and for Cold 16 – 29 °C. (Wash water temperature must
be a minimum of 16 °C for detergent activation and effective cleaning.)
English - 33
DV90F5E6HGW-03297J-06_EN_150706.indd Sec4:33
2015-07-06
1:07:57
appendix
PROTECTING THE ENVIRONMENT
This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please
observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected
to a power source. Remove the door so that animals and small children cannot get trapped inside the
appliance.
SPECIFICATIONS
C
D
A
B
TYPE
DIMENSIONS
FRONT LOADING DRYER
A. Height
85.0 cm
B. Width
60.0 cm
C. Depth with door open 90°
110.1 cm
D. Depth
60.0 cm
WEIGHT
50 kg
ELECTRICAL REQUIREMENTS
220-240 V / 50 Hz
ALLOWABLE TEMPERATURE
950 - 1100 W
5 ~ 35 °C
English - 34
DV90F5E6HGW-03297J-06_EN_150706.indd Sec4:34
2015-07-06
1:07:58
CYCLE CHART
( user option)
Max load (kg)
(Dry Laundry)
Cycle
Synthetics
Anti
Mixed Load Bell Interior Lamp Sound
Crease (Only DV9, DV8) (Only DV9, DV8) On/Off
Delay
End
DV8
Extra Dry
9
8
7






Cupboard Dry
9
8
7






Iron Dry
9
8
7


-



Extra Dry
4.5
4
3.5






Cupboard Dry
4.5
4
3.5






Iron Dry
4.5
4
3.5


-




Wool
Ultra Delicate
Outdoor (Only DV9, DV8 Series)
2
2
2
-

-


1.5
1.5
1.5
-

-



2
2
-
-

-



Sports Wear
2
2
2
-

-



Quick Dry
1
1
1
-

-



Warm Air (Only DV9, DV8 Series)
-
-
-
-

-



Cool Air
-
-
-
-

-



Time Dry
-
-
-
-

-



APPENDIX
Cotton
DV7
Drying
Level
DV9
* 9 : DV9 Series (9 kg)
* 8 : DV8 Series (8 kg)
* 7 : DV7 Series (7 kg)
CONSUMPTION DATA
Model
Program
Cotton Cupborad**
DV9 Series
Cotton Iron**
Synthetics Cupboard
Cotton Cupborad**
DV8 Series
Energy (kWh)
Max. Duration
(Minutes)
9
2.2
190
4.5
1.12
120
9
1.7
155
4.5
0.85
78
8
1.98
170
4
1.04
110
Cotton Iron**
8
1.54
140
Synthetics Cupboard
4
0.78
72
7
1.75
150
3.5
0.95
100
7
1.43
130
3.5
0.67
68
Cotton Cupborad**
DV7 Series
Load (kg)*
Cotton Iron**
Synthetics Cupboard
1. * : Weight of dry laundry
** : EN 61121:2013 test program
2. All data without a “star” against it was calculated using EN 61121:2013
Consumption data can vary from the nominal values given above depending in the size of the
load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity supply
and any extra options selected.
English - 35
DV90F5E6HGW-03297J-06_EN_150706.indd Sec4:35
2015-07-06
1:07:58
QUESTIONS OR COMMENTS?
Country
CALL
OR VISIT US ONLINE AT
AUSTRALIA
1300 362 603
www.samsung.com/au/support
DC68-03297J-06
DV90F5E6HGW-03297J-06_EN_150706.indd Sec4:36
2015-07-06
1:07:58