Samsung DW5000H Dish Washer with Flexible Loading User Manual

DW60H6050FW
DW60H6050FS
Dishwasher
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
DD81-01651H_EN_150130.indd 1
2015-01-30
3:11:28
Safety information
Please read this User Information carefully and keep it to refer to at a later date.
Pass it on to any subsequent owner of the appliance.
This manual contains sections of Safety Instructions, Part and Features,
Installation your dishwasher and Troubleshooting etc.
Carefully reading it before using the dishwasher will help you to use and maintain
the dishwasher properly.
The manufacturer, following a policy of constant development and up-dating of the product, may make
modifications without giving prior notice.
WARNING: When using your dishwasher, follow the below basic precautions including the following:
PROPER USE
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.
Do not operate your dishwasher unless all enclosure panels are properly in place. Open the door very
carefully if the dishwasher is operating. There is a risk of water squirting out.
Do not place any heavy objects of stand on the door when it is open. The appliance could tip forward.
When loading items to be washed:
- Locate sharp items so that they are not likely to damage the door seal;
- Load sharp knives with the handles up to reduce the risk of cut-type injuries;
Warning : knives and other utensils with sharp points must be loaded in the basket with their points
down or placed in a horizontal position.
Check that the detergent receptacle is empty after completion of the wash cycle.
Do not wash plastic items unless they are marked dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer’s recommendations.
Use only detergent and rinse additives designed for an automatic dishwasher. Never use soap, laundry
detergent, or hand washing detergent in your dishwasher.
Other means for disconnection from the supply must be incorporated in the fixed wiring with at least 3
mm contact separation in all poles.
Keep children away from detergent and rinse aid, keep children away from the open door of the
dishwasher, there could still be some detergent left inside.
Young children should be supervised to ensure that they do not play with the appliance.
The appliance is not intended for use by young children or infirm persons without supervision.
Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away from the dishwasher when the door is open.
The door should not be left in the open position since this could present a tripping hazard.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
During installation, the power supply must not be excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water mains using new hose sets and the old hose-sets should
not be reused.
READ AND FOLLOW THIS SAFETY INFORMATION
CAREFULLY SAVE THESE INSTRUCTIONS
2_ Safety information
DD81-01651H_EN_150130.indd 2
2015-01-30
3:11:50
DISPOSAL
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with the standard international abbreviations:
PE
PS
POM
ABS
for polyethylene, e.g. sheet wrapping material
for polystyrene, e.g. padding material
polyoxymethylene, e.g. plastic clips
Acrylonitrile Butadiene Styrene, e.g. Control Panel.
WARNING: Packaging material could be dangerous for children!
For disposing of package and the appliance please go to a recycling centre. Therefore cut off the
power supply cable and make the door closing device unusable.
Cardboard packaging is manufactured from recycled paper and should be disposed in the waste
paper collection for recycling.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local city office and
your household waste disposal service.
READ AND FOLLOW THIS SAFETY INFORMATION
CAREFULLY SAVE THESE INSTRUCTIONS
Safety information _3
DD81-01651H_EN_150130.indd 3
2015-01-30
3:11:50
Contents
PART AND FEATURES
5
INSTALLING YOUR DISHWASHER
8
USING THE DETERGENT
11
LOADING THE DISHWASHER RACKS
16
WASHING PROGRAMMES
21
CLEANING AND CARE
24
TROUBLESHOOTING
27
APPENDIX
31
5
6
7
Dishwasher features
Control panel
Displays
8
10
10
10
Water supply and drain
Connection of drain hoses
Position the appliance
Start of dishwasher
11
13
15
Fill the rinse aid dispenser
Function of detergent
How to use the Multi in 1 option
16
17
18
18
19
20
Loading the upper basket
Loading the lower basket
Folding back the cup shelves
Folding spikes of lower basket
Cutlery(silverware) basket
For washing in the dishwasher the following
cutlery/dishes
21
21
22
22
Turning on the appliance
Change the program...
At the end of the wash cycle
Wash cycle table
24
25
25
25
25
26
Cleaning the filters
Cleaning the spray arms
Cleaning the door
Caring for the dishwasher
Protect against freezing
How to keep your dishwasher in shape
27
30
Before calling for service
Error codes
31
31
Specifications
Product dimension
4_ Contents
DD81-01651H_EN_150130.indd 4
2015-01-30
3:11:50
Part and features
DISHWASHER FEATURES
Front & Rear view
01 PART AND FEATURES
1
6
2
4
7
3
8
5
4
7
8
1
3rd Rack
2
Upper Basket
3
Lower Basket
4
Duct Nozzle
5
Dispenser
6
Cup Shelf
7
Spray arms
8
Filter assembly
9
Inlet hose
10 Drain hose
10
9
Accessory parts - User manual, cutlery basket.
Part and features _5
DD81-01651H_EN_150130.indd 5
2015-01-30
3:11:50
Part and features
CONTROL PANEL
1
2
3
4
6
7
5
9
8
1
POWER BUTTON
Press this button to turn on your dishwasher: the screen lights up.
2
PROGRAM BUTTON
To select washing program press this button.
3
HALF LOAD
BUTTON
For small amount of loading items, use either the upper or lower basket
only to save energy.
Press the Half load button to select the upper or lower basket.
4
CHILD LOCK
BUTTON
This option allows you to lock the buttons on the control panel so children
cannot accidentally start the dishwasher by pressing the buttons on the
panel.
To lock and unlock the buttons on the control panel, hold down both the
Child lock buttons for three (3) seconds.
5
DISPLAY WINDOW
Running indicator, delay time, error codes and etc.
6
START BUTTON
In Power on condition, close the dishwasher door and select the cycle and
desired options. Press the START button to begin the cycle. When you
want to pause the dishwasher while running, press the START button and
make sure to open the door slowly and carefully.
You can reset the machine by pressing the START button for 3 seconds
during washing. After reset, the dishwasher goes to the initial state.
7
DELAY START
BUTTON
Press this button to set the delayed hours for washing. You can delay the
start of washing up to 24 hours. One press on this button delays the start
of washing by one hour.
8
HYGIENE BUTTON
Push the Hygiene button for the best possible hygiene in your dishwasher.
At the final rinse it heat up to 67 °C and hold this temperature for a several
minutes.
This function is available with all program except Pre Wash, Delicate and
Quick Wash.
9
MULTI IN 1 BUTTON
To select Multi in 1 option which needs rinse aid but a Multi in 1 tablet. This
option can be selected on Intensive, Auto or Normal program only.
•
•
When the door is open only the POWER button will operate.
You can select options (Multi in 1, Delay start and/or Half load) before starting a cycle.
IMPORTANT: To get the best performance from your dishwasher, read all the operating instructions
before using it for the first time.
6_ Part and features
DD81-01651H_EN_150130.indd 6
2015-01-30
3:11:52
DISPLAYS
1
1
01 PART AND FEATURES
2
3
PROGRAM ICONS
When press the Program button, each program is selected.
INTENSIVE
Heavily soiled items include pots and pans
AUTO WASH
Lightly to heavily soiled daily using items, automatic detection of the
amount of soils.
NORMAL
Normally soiled daily using items, with reduced energy and water
consumptions.
EXPRESS
Common soiled daily using items, with short cycle time.
DELICATE
Lightly soiled delicate items.
QUICK WASH
Lightly soiled with very short cycle time.
PRE WASH
Cold rinse for remove only dirt on dishes stored for a long time or
soaking dishes which are dried up before other programme running.
2
3*8 SEGMENT
Display the remaining time, error code, or delay time.
3
REFILL INDICATORS
If Rinse indicator is lit, it means rinse is needed to refill.
RINSE REFILL
INDICATOR
If the “Rinse Refill” indicator is lit, it means the dishwasher is low on
dishwasher rinse aid and requires a refill.
To refill the rinse reservior, refer to the “When to refill the rinse aid
dispenser” section on page 11.
Part and features _7
DD81-01651H_EN_150130.indd 7
2015-01-30
3:11:52
Installing your dishwasher
WARNING : Electrical shock hazard
Disconnect electrical power before installing dishwasher.
Failure to do so could result in death or electrical shock.
ATTENTION: The installation of the pipes and electrical equipments should be done by professionals.
About electricity connecting
CAUTION, for personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD GROUNDING
PRONG FROM THE POWER CORD.
Electrical requirements
•
•
An AC 220-240 V / 50 Hz fuse or a circuit breaker.
An individual branch circuit serving your dishwasher.
Grounding instructions
Insure proper ground exists before use
This appliance must be grounded. In the event of a malfunction or breakdown, grounding
will reduce the risk of electric shock by providing a path of least resistance of electric
current. This appliance is equipped with a cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropriate outlet that is installed
and grounded in accordance with all local codes and ordinances.
WARNING: Improper connection of the equipment grounding conductor can result in the
risk of an electric shock. Check with a qualified electrician or service representative if you
are in doubt whether the appliance is properly grounded. Do not modify the plug provided
with the appliance.
WATER SUPPLY AND DRAIN
Cold water connection
Connect the cold water supply hose to a threaded 3/4 (inch)
connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended
period of time, let the water run to make sure that the water is
clear. This precaution is needed to avoid the risk of the water inlet
to be blocked and damage the appliance.
Provided water supply hose has the aqua-safe system. Ensure
that water supply hose’s aqua-safe pipe is connected to the
faucet.
8_ Installing your dishwasher
DD81-01651H_EN_150130.indd 8
2015-01-30
3:11:53
Hot water connection
Positioning the appliance
Position the appliance in the desired location. The back should rest against the wall behind
it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with
water supply and drain hoses that can be positioned to the right or the left to facilitate
proper installation.
How to drain excess water from hoses
If the sink is 1000 mm higher from the floor, the excess water in hoses cannot be drained
directly into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Water outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water inlet hose is not kinked or squashed.
Extension hose
If you need a drain hose extension, Use a similar size and quality drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be
reduced.
Syphon connection
The waste connection must be at a height of between 40 cm (minimum) and 100 cm (maximum)
from the bottom of the dishwasher. The water drain hose should be fixed by a hose clip.
Aqua-safe
The Aqua-safe System is a safety valve system, preventing water leaks. If the water inlet hose
starts to leak anytime, the safety valve cuts off the running water. If the water inlet hose or the
safety valve is damaged, remove and replace it.
Do not enlarge or shorten the inlet hose.
Installing your dishwasher _9
DD81-01651H_EN_150130.indd 9
2015-01-30
3:11:53
02 INSTALLING
The water supply to the appliance can also be connected to the house hot water line (centralized
system, heating system), as long as it does not exceed a temperature of 60 °C. In this case, the
wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as those for
the connection to the cold water line.
Installing your dishwasher
CONNECTION OF DRAIN HOSES
Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let it run into the sink, making
sure to avoid bending or crimping it. The top of the hose must be at a height between 40 and 100 cm. The
free end of the hose must not be immersed in water to avoid the back flow of it.
Max 1000 mm
Drain pipe
Min. 400 mm
Counter
NOTE
The top of the hose must
be at a height between 40
and 100cm.
The free end of the hose
must not be immersed in
water.
40 mm
POSITION THE APPLIANCE
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that
can be positioned either to the right or the left sides to facilitate proper installation.
Levelling the Appliance
Once the appliance is positioned for levelling, the height of the
dishwasher may be altered via adjustment of the screwing level of the
feet. In any case, the appliance should not be inclined more than 2°.
START OF DISHWASHER
The followings should be checked before starting the dishwasher.
1. the dishwasher is level and fixed.
2. the inlet valve is opened.
3. there leakage at the connections of the conducts.
4. the wires are tightly connected.
5. the power is switched on.
6. the inlet and drain hoses are not knotted.
7. All packing materials and printings should be taken out from the dishwasher.
ATTENTION: After installation please put this manual in a safe place. The contents of this manual can
be useful to users.
10_ Installing your dishwasher
DD81-01651H_EN_150130.indd 10
2015-01-30
3:11:53
Using the detergent
FILL THE RINSE AID DISPENSER
Function of rinse aid
03 DETERGENT
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and
streak free drying.
ATTENTION: Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser
with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would
damage the appliance.
When to refill the rinse aid dispenser
If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by
the Colour of the optical level indicator “D” located next to the cap. When the rinse-aid container
is full, the whole indicator will be dark. As the rinse-aid diminishes, the size of the dark dot
decreases. You should never let the rinse aid get below 1/4 full.
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated
below.
Full
3/4 full
1/2 full
1/4 full : Should refill to eliminate spotting
Empty
D (Rinse-Aid indicator)
Using the detergent _11
DD81-01651H_EN_150130.indd 11
2015-01-30
3:11:53
Using the detergent
Rinse Aid dispenser
1. To open the dispenser, turn the cap to the “open” (left) arrow
and lift it out.
2. Pour the rinse aid into the dispenser, being careful not to
overfill.
3. Replace the cap by inserting it aligned with “open” arrow
and turning it to the closed (right) arrow.
The rinse aid is released during the final rinse to prevent water from forming droplets on your
dishes that can leave spots and streaks. It also improves drying by allowing water to water to run
off the dishes.
Your dishwashers is designed to use liquid rinse aids. The rinse aid dispenser is located inside
the door next to the detergent dispenser. To fill the dispenser, open the cap and pour the rinse
aid into the dispenser until the level indicator turns completely black. The volume of the rinse aid
container is about 130 ml.
Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any
spills with a damp cloth. Don’t forget to replace the cap before you close dishwasher door.
ATTENTION: Clean up any rinse aid spilt during filling with an absorbent cloth to avoid
excess foaming during the next wash.
Adjusting rinse aid dispenser
The rinse aid dispenser has four settings. Always start with the
dispenser set on “3”. If spots and poor drying are problems,
increase the amount of rinse aid dispensed by removing the
dispenser lid and rotating the dial to “4”. We suggest you to set
on “3” (Factory value is “3”).
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or
knife blades.
12_ Using the detergent
DD81-01651H_EN_150130.indd 12
2015-01-30
3:11:53
FUNCTION OF DETERGENT
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the
dishwasher. Most of commercial quality detergents are suitable for this purpose.
WARNING: Dishwasher detergent is corrosive! Take care to keep it out of reach of children.
Concentrated detergent
Based on their chemical composition, dishwasher detergent can be split in two basic types:
• conventional, alkaline detergents with caustic components
• low alkaline concentrated detergents with natural enzymes
The use of “normal” washing programmes in conjunction with concentrated detergents reduces
pollution and is good for your dishes; these wash programmes are specially matched to the
dirt-dissolving properties of the enzymes of the concentrated detergent. For this reason “normal”
wash programmes in which concentrated detergents are used can achieve the same results that
can otherwise only be achieved using “intensive” programmes.
Detergent tablets
Detergent tablets of different brands dissolve at different speeds. For this reason some detergent
tablets cannot dissolve and develop their full cleaning power during short programmes.
Therefore please use long programmes when using detergent tablets, to unsure the complete
removal of detergent residuals.
Detergent dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the Wash Cycle Table. Your dishwasher uses less detergent and rinse aid then
conventional dishwashers. Generally, only one tablespoon of detergent is needed for a normal
wash load. Also, more heavily soiled items need more detergent. Always add the detergent just
before starting the dishwasher, otherwise it could get damp and will not dissolve properly.
Fill the detergent in dispenser
1. If the lid is closed: press release button. The lid springs
open.
Push latch to open
2. Always add the detergent just before starting each
wash cycle. Only use branded detergent aid for
dishwasher.
Using the detergent _13
DD81-01651H_EN_150130.indd 13
2015-01-30
3:11:53
03 DETERGENT
Proper Use of Detergent
Use only detergent specifically made for use in dishwashers. Keep your detergent fresh and dry. Don’t
put powder detergent into the dispenser until you’re ready to wash dishes.
Using the detergent
Amount of detergent to use
1. Fill the detergent dispenser with detergent.
The marking indicates the dosing levels, as illustrated on
right:
A. This section is for main wash detergent, approximately
27.5 g
B. This section is for the pre wash detergent,
approximately 5 g
If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent chamber. This
detergent will take effect during the pre-wash phase.
You can find information about the amount of detergent
for the single programmes on the “Wash cycle table”.
(See page 22)
Please be aware, that according to the soiling level and
the specific hardness of water differences are possible.
A
B
2. Close the lid and press until it locks in place.
Please observe the manufacturers dosing and storage recommendations as stated on the
detergent packaging.
Detergents
There are 3 sorts of detergents.
1. With phosphate and with chlorine.
2. With phosphate and without chlorine.
3. Without phosphate and without chloride.
Normally new pulverised detergent is without phosphate. If detergents without phosphate were
used in case of hard water often white spots appear at dishes and glasses. In this case please
add more detergent to reach better results. Detergents without chlorine do only bleach a little.
Strong and coloured spots will not removed completely. In this case please choose a programme
with higher temperature.
14_ Using the detergent
DD81-01651H_EN_150130.indd 14
2015-01-30
3:11:53
HOW TO USE THE MULTI IN 1 OPTION
Your dishwasher has a Multi in 1 option which does not need rinse aid but a 3 In1 tablet. This option can
select on Intensive, Normal program only.
03 DETERGENT
The Multi in 1 setting is only for use with Multi in 1 tablets. If using Multi in 1 tablet without this option,
the appliance will not get it’s best performance.
1. Put the Multi in 1 tablet into the container then start the Multi in 1
option.
2. Close the lid and press until it locks in place.
When using Multi in 1 compact combination detergents ensure
that the lid can be closed correctly.
ATTENTION: Keep all detergents in a safe place out of
children’s reach. Always add the detergent in the dispenser just
before starting the dishwasher.
Using the detergent _15
DD81-01651H_EN_150130.indd 15
2015-01-30
3:11:54
Loading the dishwasher racks
For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of racks and silverware baskets may vary from your
model.
Attention before or after loading the dishwasher racks
Scrape off any large amounts of leftover food. It is not necessary to rinse the dishes under running
water. Place objects in the dishwasher in the following order:
1. Items such as cups, glasses, pots/pans, etc. are stood upside down.
2. Curved items, or those with recesses, should be at a slant so that water can run off.
3. They are stacked securely and can not tip over.
4. They do not prevent the spray arms from rotating while washing takes place.
Very small items should not be washed in the dishwasher as they could easily fall out of the racks.
Removing the dishes
To prevent water dripping from the upper basket into the lower basket, we recommend that you empty
the lower basket first and then the upper basket.
LOADING THE UPPER BASKET
The upper basket is designed to hold more delicate and lighter dishware such as glasses, coffee and tea
cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty).
Position the dishes and cookware so that they will not get moved by the spray of water. Always place
glasses, cups & bowls upside down.
c
a
c
a
a
a
a
c
a
a
b
a
c
a
c
c
c
c
a
c
a a
c
c
a a
c
c
c
IN
14 place setting
Cups
a
c
d
Saucers
Glasses
Dinner plates
e
f
Soup plates
Dessert dishes
b
16_ Loading the dishwasher racks
DD81-01651H_EN_150130.indd 16
2015-01-30
3:11:54
Adjusting the Upper Basket
The height of the upper basket can be adjusted in order to create more space for large utensils
both for the upper/lower basket.
04 LOADING THE RACKS
1. To lower the upper rack, press the “A”
levers located at the left and right sides
of the upper basket and push the upper
basket downwards slightly at the same
time.
2. To raise the upper rack, just pull the
upper basket upwards without operating
any levers.
Caution: We recommend adjusting
the height of the upper basket before
loading dishes into the basket. If you
adjust the the basket after loading the
dishes, you may damage the dishes.
To lower position
To upper position
LOADING THE LOWER BASKET
We recommend that you place large items which are most difficult to clean in to the lower rack: pots, pans,
lids, serving dishes and bowls, as shown in the figure to the right. It is preferable to place serving dishes and
lids on the side of the racks in order to avoid blocking the rotation of the top spray arm. Pots, serving bowls,
etc. must always be placed top down. Deep pots should be slanted to allow water to flow out.
The bottom rack feature fold down tine rows so that larger or more pots and pans can be loaded.
e
d
IN
f
f
f
b
14 place setting
IN
b
d
e
f
Saucers
Dinner plates
Soup plates
Dessert dishes
Long items, serving cutlery, salad servers and big knives should be placed on the shelf so that they do
not obstruct the rotation of the spray arms.
Loading the dishwasher racks _17
DD81-01651H_EN_150130.indd 17
2015-01-30
3:11:55
Loading the dishwasher racks
FOLDING BACK THE CUP SHELVES
For better stacking of pots and pans, the shelves can be folded down as shown in the picture below.
FOLDING SPIKES OF LOWER BASKET
For better stacking of pots and pans, the spikes can be folded down as shown in the picture right.
18_ Loading the dishwasher racks
DD81-01651H_EN_150130.indd 18
2015-01-30
3:11:55
CUTLERY(SILVERWARE) BASKET
Silverware should be placed in the cutlery basket with handles at the bottom: The spoon should be loaded
individually into the appropriate slots, especially long utensils should be placed in the horizontal position at
the front of the upper basket.
04 LOADING THE RACKS
4
5
3
IN
1
2
2
1
3
5
4
1
Forks
4
Teaspoons
2
Soup spoons
5
Knives
3
Dessert spoons
WARNING
•
•
Do not let any item extend through the bottom.
Always load sharp utensils with the sharp point down!
Loading the dishwasher racks _19
DD81-01651H_EN_150130.indd 19
2015-01-30
3:11:55
Loading the dishwasher racks
FOR WASHING IN THE DISHWASHER THE FOLLOWING CUTLERY/
DISHES
Are not suitable
Are of limited suitability
Cutlery with wooden, horn china or mother-of-pearl
handles.
Plastic items that are not heat resistant Older
cutlery with glued parts that is not temperature
resistant Bonded cutlery items or dishes Pewter
or cooper items Lead crystal glass Steel items
subject to rusting Wooden platters Items made from
synthetic fibres.
Some types of glasses can become dull after a
large number of washes.
Silver and aluminium parts have a tendency to
discolour during washing.
Glazed patterns may fade if machine washed
frequently.
Do not try and wash items soiled with cigarette ash, candle wax, lacquer or paint. If you buy new
dishes please make sure that they are suitable for dishwashers.
Please do not overload your dishwasher. There is only space for 12 standard dishes. Do not use dish
that are not suitable for dishwashers. This is important for good results and for reasonable energy
consumption.
When loading the dishes and cutlery
Dishes and cutlery must not impede the rotation of the spray arms.
Load hollow items such as cups, glasses, pans etc. with the opening downwards so that water
cannot collect in the container or a deep base.
Dishes and items of cutlery must not lie inside one another, or cover each other
•
•
•
To avoid damage to glasses, they must not touch.
Load large items which are most difficult to clean into the lower rack.
The upper rack is designed to hold more delicate and lighter dishware such as glasses,
coffee and tea cups.
ATTENTION
Long bladed knives stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in
the upper basket.
Damage to glassware and other dishes.
Possible causes
Suggested remedy
•
•
•
Type of glass or manufacturing process.
Chemical composition of detergent.
Water temperature and duration of
dishwasher programme.
•
•
•
Use glassware or porcelain dishes that
have been marked dishwasher-proof by
the manufacturer
Use a mild detergent that is described as
kind of dishes If necessary, seek further
information from detergent manufacturers.
Select a programme with as low a
temperature.
To prevent damage, take glass and cutlery
out of the dishwasher as soon as possible
after the programme has ended.
20_ Loading the dishwasher racks
DD81-01651H_EN_150130.indd 20
2015-01-30
3:11:56
Washing programmes
TURNING ON THE APPLIANCE
Program
05 WASHING PROGRAMMES
Starting a cycle wash
1. Draw out the lower and upper basket, load the dishes and push them back..
It is recommended to load the lower basket first, then the upper one (see the section entitled “Loading
the dishwasher racks”).
2. Pour in the detergent (see the section entitled “Using the detergent”).
3. Insert the plug into the socket. The power supply is 220-240 VAC / 50 HZ, the specification of the
socket is 15A 250 VAC. Make sure that the water supply is turned on to proper pressure.
4. Close the door, press the POWER button, to switch on the machine.
5. Press the Program button, the wash program will be changed as follows direction:
Normal  Express  Quick Wash  Delicate  Pre Wash  Intensive  Auto
If a wash program is selected, the response light will light. Then press the START button, the
dishwasher begins to start.
When you press the START button to pause during washing, the running indicator will stop blinking
and the dishwasher will beep every minute unless you press the START button to start.
CHANGE THE PROGRAM...
Premise:
1. A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have already been released, and the appliance may have already drained the wash water.
If this is the case, the detergent dispenser must be refilled (see the section entitled “Fill the detergent in
dispenser”).
2. Press the STARTbutton, the machine will be in standby state, press the Program button more than
3 seconds then you can change the program to the desired cycle setting.
If you open the door during a wash cycle, the machine will pause. The program light will stop blinking
and the buzzer will beep every minute unless you close the door. After you close the door, the machine
will keep on working after 3 seconds automatically.
If your model has broken memory function, the machine will go on to finish the selected program after
the power cut.
Add a dish
A forgotten dish can be added at any time before the detergent dispenser opens.
1. Press the START button and make sure to open the door slowly and carefully as there is a
possibility of injury from the hot steam inside the dishwasher.
2. After the spray arms stop working, you can open the door completely.
3. Add forgotten dishes.
4. Close the door. The dishwasher will work after 3 seconds.
WARNING: It is dangerous to open the door when washing, because the hot water may
scald you. If the door is opened while the dishwasher is running, a safety mechanism is
activated and stops the cycle.
Washing programmes _21
DD81-01651H_EN_150130.indd 21
2015-01-30
3:11:56
Washing programmes
AT THE END OF THE WASH CYCLE
When the working cycle has finished, the buzzer of dishwasher will beep shortly, then stop. In the digital
display appears “End”, only in this case the programme has ended.
1. Switch off the dishwasher by pressing the POWER button.
2. Turn off the water tap!
Open the door carefully. Hot steam may escape when the door is opened!
•
•
•
Hot dishes are sensitive to knocks. The dishes should be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher’s door, leave it and wait a few minutes before removing the dishes. In this
way they will be cooler and the drying will be improved.
Unloading the dishwasher.
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper
basket onto the dishes in the lower one.
WASH CYCLE TABLE
DW60H6050
Program
Description of cycle
Detergent
(Prewash/Main wash) (g)
Running
time (min)
Energy
(kWh)
Water (ℓ)
5/27.5
175
1.65
18
5/27.5
195
1.75
18
5/27.5
165
0.74
12.5
5/27.5
180
1.05
12.5
Pre Wash (50 °C)
Wash (60 °C)
Intensive
Rinse
Rinse
Rinse (65°C)
Drying
Pre Wash (50 °C)
Wash (60 °C)
Intensive + Hygiene
Rinse
Rinse
Rinse (70 °C)
Drying
Pre Wash
Wash (45°C)
Normal
Rinse
Rinse (50 °C)
Drying
Pre Wash
Wash (45°C)
Normal + Hygiene
Rinse
Rinse (70 °C)
Drying
22_ Washing programmes
DD81-01651H_EN_150130.indd 22
2015-01-30
3:11:56
Program
Description of cycle
Detergent
(Prewash/Main wash) (g)
Running
time (min)
Energy
(kWh)
Water (ℓ)
5/27.5
115
0.9
14
5/27.5
60
1
10.5
5/27.5
80
1.25
10.5
20
35
0.6
11.5
20
50
1.15
11.5
5/27.5
120 ~ 180
0.9 ~ 1.3
8.5 ~ 12.5
5/27.5
120 ~ 180
0.9 ~ 1.3
8.5 ~ 12.5
Pre Wash
Wash (40 °C)
Rinse
05 WASHING PROGRAMMES
Delicate
Rinse (60 °C)
Drying
Pre Wash
Express
Wash (60 °C)
Rinse (60 °C)
Drying
Pre Wash
Express + Hygiene
Wash (60 °C)
Rinse (70 °C)
Drying
Wash (40 °C)
Quick Wash
Rinse
Rinse (45°C)
Wash (40 °C)
Quick Wash + Hygiene
Rinse
Rinse (70 °C)
Pre Wash (45 °C)
Auto (45 ~ 55 °C)
Auto
Rinse
Rinse (60 °C)
Drying
Pre Wash (45 °C)
Wash (45 ~ 55 °C)
Auto + Hygiene
Rinse
Rinse (70 °C)
Drying
* AS/NZS 2007.1: This program is the test cycle. The information for comparability test in accordance
with AS/NZS 2007.1, as follows:;
•
•
•
Capacity: 14 place setting
Position of Upper Basket: to lower position
Rinse aid setting: 4
The wash time varies depending on the pressure and temperature of the supplied water.
Open the door slightly 50mm to assist in drying of the dishes after every wash.
Washing programmes _23
DD81-01651H_EN_150130.indd 23
2015-01-30
3:11:56
Cleaning and care
CLEANING THE FILTERS
Filtering system
For your convenience, we have placed the drain pump and filtering system within easy reach
inside the tub. There are three components of the filtering system: the main filter, the coarse filter,
and the fine filter.
1. Main filter: Food and soil particles trapped by this filter are
pulverized by a special jet on the lower spray arm and washed down
the drain.
2. Coarse filter: Larger items, such as pieces of bone or glass, that
could clog the drain are trapped in the coarse filter. To remove an
item caught in this filter, gently squeeze the tabs on top of this filter
and lift it out.
3. Fine filter: This filter holds soil and food residue in the sump area
and prevents it from being redeposited on the dishes during a cycle.
2
1
3
ATTENTION: Do not put the fine filter upside down.
Filter assembly
For best performance and results, the filter assembly must be cleaned. The filter efficiently
removes food particles from the wash water, allowing it to be recirculated during the cycle.
For this reason, it is a good idea to remove the larger food particles trapped in the filter after
each wash cycle by rinsing the semicircular filter and cup under running water. To remove the
filter assembly, turn it in anti-clockwise direction and lift the filter assembly up. The entire filter
assembly should be cleaned regularly.
To clean the coarse filter and the fine filter, use a cleaning brush. Then, reinsert the entire
assembly in the dishwasher, positioning in its seat, pressing downward, turning it clockwise
direction.
Open
The dishwasher must never be used without the filters. Improper replacement of the filter may
reduce the performance level of the appliance and damage dishes and utensils.
WARNING: Never run the dishwasher without the filters in place. When cleaning the filters,
do not damage them. Otherwise the filters may not perform as intended and poor wash
results or damage to the internal parts may be encountered.
24_ Cleaning and care
DD81-01651H_EN_150130.indd 24
2015-01-30
3:11:56
CLEANING THE SPRAY ARMS
06 CLEANING AND CARE
It is necessary to clean the spray arms regularly as hard water chemicals may
clog the spray arm jets and bearings. To remove the middle spray arm, hold the
nut, rotate the arm clockwise to remove it. To remove the lower spray arm, pull
out the spray arm upward. Wash the arms in soapy and warm water and use a
soft brush to clean the jets. Replace them after rinsing them thoroughly.
Open
CLEANING THE DOOR
To clean the edge around the door, you should use only a soft warm, damp rag.
To prevent penetration of water into the door lock and electrical components,
do not use a spray cleaner of any kind.
Also, never use abrasive cleaners or scouring pads on the outer surfaces
because they will scratch the finish. Some papers towels can also scratch or
leave marks on the surface.
WARNING: Never use a spray cleaner to clvean the door panel for it could damage the door lock and
electrical components. It is not advised to use the abrasive agent or some paper towel because of the
risk of scratching or leaving spots on the stainless steel surface.
CARING FOR THE DISHWASHER
To clean the control panel use a lightly damp cloth then dry thoroughly. To clean the exterior use a good
appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
PROTECT AGAINST FREEZING
If your dishwasher is left in an unheated place during the winter:
1. Cut off electrical power to the dishwasher.
2. Turn off the water supply and disconnect the water inlet pipe from the water valve.
3. Drain water from the inlet pipe and water valve. (Use a pan to catch the water)
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter in the tub the bottom and use a sponge to use up water in sump.
Cleaning and care _25
DD81-01651H_EN_150130.indd 25
2015-01-30
3:11:56
Cleaning and care
HOW TO KEEP YOUR DISHWASHER IN SHAPE
•
•
•
•
•
•
After Every Wash
After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that
moisture and odours not trapped inside.
Remove the Plug
Before cleaning or performing maintenance, always remove the plug from the socket.
No Solvents or Abrasive cleaning
To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning
products. use only a cloth and warm soapy water. To remove spots or stains from the surface of
the interior, use a cloth dampened with water and a little white vinegar, or a cleaning product made
specifically for dishwashers.
When You Go on Holiday
When you go on holiday, it is recommened that you run a wash cycle with the dishwasher empty and
then remove the plug from the socket, turn off the water supply and leave the door of the appliance
slightly ajar. This will help the seals last longer and prevent odours from forming within the appliance.
Moving the Appliance
If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be
positioned on its back.
Seals
One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this from occurring.
26_ Cleaning and care
DD81-01651H_EN_150130.indd 26
2015-01-30
3:11:56
Troubleshooting
The manufacturer, following a policy of constant development and up-dating of
the product, may make modifications without giving prior notice.
BEFORE CALLING FOR SERVICE
POSSIBLE CAUSE
WHAT TO DO
•
Fuse blown or the circuit
breaker acted.
•
Replace fuse or reset circuit breaker.
Remove any other appliances sharing the
same circuit with the dishwasher.
•
Power supply is not turned
on.
•
Make sure the dishwasher is turned on
and the door is closed securely.
Make sure the power cord is properly
plugged into the wall socket.
•
Water pressure is low.
•
Check that the water supply is connected
properly and the water is turned on.
Drain pump doesn’t
stop
•
Overflow.
•
The system is designed to detect an
overflow. When it does, it shuts off the
circulation pump and turns on the drain
pump.
Noise
•
Some audible sounds are
normal.
•
Sound from soft food shredding action
and detergent cup opening.
•
Utensils are not secure in
the baskets or something
small has dropped into the
basket.
•
To ensure everything is secured in the
dishwasher.
•
Motor hums.
•
Dishwasher has not been used regularly.
If you do not use it often, remember to
set it to fill and pump out every week,
which will help keep the seal moist.
•
Improper detergent.
•
Use only the special dishwasher
detergent to avoid suds.
If this occurs, open the dishwasher and
let suds evaporate.
Add 1 gallon of cold water to the tub.
Close and latch the dishwasher, then
start the “soak” wash cycle to drain out
the water. Repeat if necessary.
Suds in the tub
•
•
•
Spilled rinse agent.
•
Always wipe up rinse agent spills
immediately.
Stained tub interior
•
Detergent with colorant
was used.
•
Make sure that the detergent is the one
without colorant.
Dishes are not dried
•
Rinse agent dispenser is
empty.
•
Make sure that the rinse agent dispense
is filled.
Dishes and flatware
not clean
•
Improper program.
•
Select a more intensive wash program.
•
Improper rack loading.
•
Make sure that the action of the detergent
dispenser and spray arms are not
blocked by large dishware.
Troubleshooting _27
DD81-01651H_EN_150130.indd 27
2015-01-30
3:11:56
07 TROUBLESHOOTING
PROBLEM
Dishwasher doesn’t
run
Troubleshooting
PROBLEM
POSSIBLE CAUSE
WHAT TO DO
Spots and filming on
glasses and flatware
1. Extremely hard water.
2. Low inlet temperature.
3. Overloading the
dishwasher.
4. Improper loading.
5. Old or damp powder
detergent.
6. Empty rinse agent
dispenser.
7. Incorrect dosage of
detergent.
To remove spots from glassware:
1. Take out all metal utensils out of the
dishwasher.
2. Do not add detergent.
3. Choose the longest cycle.
4. Start the dishwasher and allow it to run
for about 18 to 22 minutes, then it will be
in the main wash.
5. Open the door to pour 2 cups of white
vinegar into the bottom of the dishwasher.
6. Close the door and let the dishwasher
complete the cycle. If the vinegar does
not work: Repeat as above, except use
1/4 cup (60 ml) of citric acid crystals
instead of vinegar.
Cloudiness on
glassware
•
Combination of soft water
and too much detergent.
•
Use less detergent if you have soft water
and select a shortest cycle to wash the
glassware and to get them clean.
Tea or coffee stains.
•
Using a solution of 1/2 cup of bleach and
3 cups warm water to remove the stains
by hand.
Yellow or brown film on •
inside surfaces
WARNING: You have to wait for
20 minutes after a cycle to let the
heating elements cool down before
cleaning interior; Failing to follow this
instruct may result in the risk of burns.
White film on inside
surface
•
Hard water minerals.
•
To clean the interior, use a damp sponge
with dishwasher detergent and wear
rubber gloves. Never use any other
cleaner than dishwasher detergent for the
risk of foaming or suds.
Detergent cup lid won’t •
latch
Dial is not in the OFF
position.
•
Turn the Dial to OFF position and slide the
door latch to the left.
Detergent left in
dispenser cups
•
Dishes block detergent
cups.
•
Re-loading the dishes properly.
Steam
•
Normal phenomenon.
•
There is some steam coming through the
vent by the door latch during drying and
water draining.
Black or gray marks on
dishes
•
Aluminum utensils have
rubbed against dishes.
•
Use a mild abrasive cleaner to eliminate
those marks.
Water standing in the
bottom of the tub
•
This is normal.
•
A small amount of clean water around the
outlet on the tub bottom keeps the water
seal lubricated.
28_ Troubleshooting
DD81-01651H_EN_150130.indd 28
2015-01-30
3:11:57
PROBLEM
Dishwasher leaks
WHAT TO DO
Overfill dispenser or rinse
aid spills.
•
Be careful not to overfill the rinse aid
dispenser.
Spilled rinse aid could cause overusing
and lead to overflowing.
Wipe away any spills with a damp cloth.
•
Dishwasher isn’t level.
•
Make sure the dishwasher is level.
•
Door is open.
•
When door is opened, buttons are not
working except POWER button. Close
the door and press the button.
•
Child lock function is
selected.
•
When selected Child lock function,
buttons are not responded. To unlock
this function, hold down both the Multi in 1
and Delay start buttons for three (3)
seconds.
Also, Child lock function is released when
power cord is reconnected.
The result of washing performance may be caused by a power supply issue. Try another program
before contacting for service.
Troubleshooting _29
DD81-01651H_EN_150130.indd 29
2015-01-30
3:11:57
07 TROUBLESHOOTING
Buttons are not
working on power on
state
POSSIBLE CAUSE
•
Troubleshooting
ERROR CODES
If an error occurs an error code may be displayed to inform you:
CODES
MEANING
Water supply error
Inlet water continually for 4 minutes in any case or no water in
normal water inlet step.
Over 2 L inletting except water inlet step.
• If water inletting below low level quantity at step when
heater work, heater is not work by safety device.
• If water inletting over low level quantity at any step, heater
is controlled by thermister.
Heater error
Heating continually for 60 minutes, yet still not arrive the
anticipated temperature.
The water level is low in the tub
Leakage error
If the leakage switch is on for 2 seconds.
When power S/W is off, LE error is not occurred when
happen the leakage on off-state, but if the door is closed, the
washer can drain away the water automatically when happen
the leakage on off-state.
Failure of
temperature sensor
Abnormal of the thermistor (short circuit/open circuit)
4E
HE
LE
tE
POSSIBLE CAUSES
WARNING: If overflow occurs, turn off the main water supply before calling a service. If there is water
in the base pan because of an over fill or small leak, the water should be removed before restarting the
dishwasher.
30_ Troubleshooting
DD81-01651H_EN_150130.indd 30
2015-01-30
3:11:57
Appendix
SPECIFICATIONS
DW60H6050FW / DW60H6050FS
Type
Freestanding Dishwasher
Power
220 - 240 V / 50 Hz AC only
Water pressure
0.04 ~ 1.0 MPa
Rated power usage
1760 - 2100 W
Hot water connection
Max 60 °C
Dry type
Condensed dry system
Wash type
Rotating nozzle spray
Dimensions
598 x 600 x 845 mm (Width × Depth × Height)
Weight
Unpacked 51 kg
08 APPENDIX
Model
PRODUCT DIMENSION
600
598
845
670
50
745
1175
Appendix _31
DD81-01651H_EN_150130.indd 31
2015-01-30
3:11:57
For standard test
The infofmation for comparability test in accordance with AS/NZS 2007.1 AS follows:
The diagrams below show the proper way to load the baskets based on the Australia Standard (AS/
NZS 2007.1)
•
•
•
•
•
•
•
•
Washing capacity: 14 place setting
Test standard: AS/NZS 2007.1
Position of upper basket: to lower position
Wash cycle: Normal
Additional options: None
Rinse aid setting: 3
Dosage of the standard detergent: pre/wash 5 g + main/wash 27.5 g
For the arrangement of the items, refer below figures
<Upper basket>
c
a
c
a
a
a
a
<Lower basket>
c
a
a
b
a
c
a
c
c
e
c
c
a
c
a a
c
c
a a
c
c
c
d
f
f
f
b
<Silverware basket>
4
5
3
1
2
2
1
1
Forks
2
Soup spoons
3
Dessert spoons
4
Teaspoons
5
Knives
3
5
4
32_ For standard test
DD81-01651H_EN_150130.indd 32
2015-01-30
3:11:57
Terminology for dishwasher
1. Circulation Motor
A motor that sucks the water remaining on the floor of the dishwater and
infects water using high pressure through the internal water passages to
the top Middle and lower nozzles.
2. Drain Pump
The pump that drains the polluted water from the dishwater generated
while the dishwater is running.
3. Heater
The healer is located on the water passages inside the dishwasher. It heats
the flowing water to increase wash efficiency.
4. Flow Meter
Measure the amount of supplied water by counting the pulses of the hall IC
located at the next of the inlet valve.
5. Distributor
Located at the output end of the sump inside the dishwasher. It turns the
flow of the water that goes to the bottom part of the dishwasher on or off.
(This model does not have this part)
6. Dispenser
The location where the detergent and rinse aids are stored so they can be
used by the dishwasher.
The dispenser automatically supplies detergent and rinse aids to the inside
of the dishwasher when they are needed.
7. Tub Assy
An internal case mode of stainless steel that makes up the basic
framework of the dishwasher.
8. Sump Assy
The place inside the dishwasher where water is collected. The injected
water gathers here after circulation.
The sump Assy is connected to the circulation motor and drain pump.
9. Tub Front Assy
An internal case made of stainless steel that makes up internal part of the
front door.
10. Base Assy
A plastic part that makes up the basic bottom framework.
11. Basket Assy
The upper and lower racks where dishes can be loaded.
12. Middle/Lower Nozzles
Washes dishes by rotating and injecting the supplied water through the
water passage at high pressure.
13. Case Brake
A passage that adjusts the air pressure by connecting the pressure of the
inside air which is expanded at high temperature during wash and rinse
cycles and the outside air pressure.
14. Door Lock Switch
Detects whether the door of the dishwasher is open or closed if the door is
open while the dishwasher is running the cycle is temporary stopped.
Terminology for dishwasher _33
DD81-01651H_EN_150130.indd 33
2015-01-30
3:11:57
Note
DD81-01651H_EN_150130.indd 34
2015-01-30
3:11:57
Note
DD81-01651H_EN_150130.indd 35
2015-01-30
3:11:57
QUESTIONS OR COMMENTS
COUNTRY
CALL
OR VISIT US ONLINE AT
AUSTRALIA
1300 362 603
www.samsung.com/au/support
DD81-01651H-00
DD81-01651H_EN_150130.indd 36
2015-01-30
3:11:57