advertisement
HP Deskjet D5500 Printer series
Contents
2 Finish setting up the HP Printer
Wireless Connection using One Button Wireless Setup with a WPS enabled router.................5
1
2
1 How Do I?
Learn how to use your HP Printer
•
•
•
Wireless Connection using One Button Wireless Setup with a WPS enabled router
How Do I?
3
Chapter 1
4 How Do I?
2 Finish setting up the HP Printer
•
Wireless Connection using One Button Wireless Setup with a WPS enabled router
•
Traditional Wireless Connection
•
•
Install the software for a network connection
Wireless Connection using One Button Wireless Setup with a WPS enabled router
To connect the HP Printer to a wireless network using WiFi Protected Setup (WPS), you will need the following:
❑ A wireless 802.11 network that includes a WPS-enabled wireless router or access point.
❑ A desktop computer or laptop with either wireless networking support, or a network interface card (NIC). The computer must be connected to the wireless network that you intend to install the HP Printer on.
Wireless Connection using One Button Wireless Setup with a WPS enabled router
1.
Do one of the following:
Use Push Button (PBC) method
a. Set up wireless connection.
❑ Press and hold the Wireless button for two seconds.
❑ Press the corresponding button on the WPS-enabled router or other networking device.
❑ The Wireless icon and signal strength bar appear solid on successful configuration of the wireless network.
b. Install Software.
NOTE:
The product begins a timer for approximately two minutes in which the corresponding button on the networking device needs to be pressed.
Wireless Connection using One Button Wireless Setup with a WPS enabled router 5
Chapter 2
Use PIN method
a. Load paper.
❑ Insert stack of paper into input tray with short edge forward and print side down.
❑ Slide stack of paper forward until it stops.
❑ Slide paper-width guide to the right until it stops at edge of paper.
b. Initiate WiFi Protected Setup.
❑ Press and hold the Resume button for two seconds.
❑ Wireless test starts.
❑ Wireless test report and Network Configuration report are printed automatically.
c. Set up wireless connection.
❑ Press and hold the Wireless button for two seconds.
❑ Enter the PIN on a computer for the router.
❑ The Wireless icon and signal strength bar appear solid on successful configuration of the wireless network.
d. Install software
NOTE:
The product begins a timer for approximately two minutes in which the corresponding button on the networking device needs to be pressed.
2.
View the animation for this topic.
Related topics
Install the software for a network connection
Test wireless setup and print network configuration page
The wireless network test performs a series of diagnostic tests to determine whether network setup is successful. You can print the wireless network test at any time.
You can print a network configuration page to see network settings such as the IP address, communication mode, and network name (SSID).
To print the network configuration page
▲ Press and hold the Resume button to initiate the wireless test and print the Network
Configuration and Network Test pages.
6 Finish setting up the HP Printer
Traditional Wireless Connection
To connect the HP Printer to an integrated wireless WLAN 802.11 network, you will need the following:
❑ A wireless 802.11 network that includes a wireless router or access point.
If you connect the HP Printer on a wireless network that has Internet access, HP recommends that you use a wireless router (access point or base station) that uses
Dynamic Host Configuration Protocol (DHCP).
❑ A desktop computer or laptop with either wireless networking support, or a network interface card (NIC). The computer must be connected to the wireless network that you intend to install the HP Printer on.
❑ Network name (SSID).
❑ WEP key or WPA Passphrase (if needed).
To connect the product
1.
Insert the product Software CD in the computer CD-ROM drive.
2.
Follow the instructions on the screen.
When you are prompted, connect the product to the computer using the USB setup cable included in the box. The product will attempt to connect to the network. If the connection fails, follow the prompts to correct the problem, and then try again.
3.
When the setup is finished, you will be prompted to disconnect the USB cable and test the wireless network connection. Once the product connects successfully to the network, install the software on each computer that will use the product over the network.
Related topics
Install the software for a network connection
USB Connection
The HP Printer supports a rear USB 2.0 High Speed port for connection to a computer.
If you use a USB cable to connect the HP Printer to a computer on a network, you can set up printer sharing on your computer. This enables other computers on the network to print to the HP Printer, using your computer as the host.
The host computer (your computer, connected directly to the HP Printer by a USB cable) has full software functionality. Other computers, which are referred to as the clients, have access only to the print features. HP recommends up to 5 computers for the best performance. You must perform other functions from the host computer or from the control panel on the HP Printer.
To connect the product with the USB cable
▲ Refer to the Start Here guide that came with your product for information on connecting to a computer with a USB cable.
NOTE:
Do not connect the USB cable to the product until you are prompted to do so.
USB Connection 7
Chapter 2
To enable printer sharing on a Windows computer
▲ Refer to the user guide that came with your computer or see the Windows onscreen
Help.
Install the software for a network connection
Use this section to install the HP Photosmart software on a computer connected to a network. Before you install the software, make sure you have connected the HP Printer to a network. If the HP Printer has not been connected to a network, follow the onscreen instructions during the software installation to connect the product to the network.
NOTE:
If your computer is configured to connect to a series of network drives, make sure that your computer is currently connected to these drives before installing the software. Otherwise, the HP Photosmart software installer might try to use one of the reserved drive letters and you will not be able to access that network drive on your computer.
NOTE:
Installation time can range from 20 to 45 minutes depending on your operating system, the amount of available space, and the processor speed of your computer.
To install the Windows HP Photosmart Software on a networked computer
1.
Quit all applications running on your computer.
2.
Insert the Windows CD that came with the product into the CD-ROM drive on your computer and follow the onscreen instructions.
NOTE:
If the HP Printer is not connected to a network, connect the product to the computer using the USB setup cable included in the box. Do not connect the
USB setup cable to the computer until prompted. The product will then attempt to connect to the network.
3.
If a dialog box about firewalls appears, follow the instructions. If you see firewall popup messages, you must always accept or allow the pop-up messages.
4.
On the Connection Type screen, select an appropriate option, and then click Next.
The Searching screen appears as the Setup program searches for the product on the network.
5.
On the Printer Found screen, verify that the printer description is correct.
If more than one printer is found on the network, the Printers Found screen appears.
Select the product you want to connect.
6.
Follow the prompts to install the software.
When you have finished installing the software, the product is ready for use.
7.
To test your network connection, go to your computer and print a self-test report to the product.
8 Finish setting up the HP Printer
3 Get to know the HP Printer
•
•
Printer parts
1 Control panel
2 Output tray
3 Input tray
4 Input tray extender
5 Front access door
6 Print cartridges
7 Cartridges access area
8 USB port
9 Rear access door
10 Power connection: Use only with the power adapter supplied by HP
Printer parts 9
Chapter 3
Control panel features
Wireless
6
1 On: Turns the product on or off. When the product is off, a minimal amount of power is still used. To completely remove power, turn off the product, then unplug the power cord.
2 Wireless: Turns the wireless radio on or off.
3 Wireless signal and ink level LCD: Shows wireless signal strength and current ink level.
4 Resume: Instructs the HP Printer to continue after a problem is solved. If pressed and held for two seconds the HP Printer prints the Network Configuration and Network Test pages.
5 Cancel: Cancels the current active printing, or alignment job, or WPS process in the system.
6 Error light: Flashes if the HP Printer has an error.
10 Get to know the HP Printer
4 Print
Choose a print job to continue.
Related topics
•
•
Recommended papers for printing
Print documents
Most print settings are automatically handled by the software application. You need to change the settings manually only when you change print quality, print on specific types of paper or transparency film, or use special features.
To print from a software application
1.
Make sure you have paper loaded in the input tray.
2.
On the File menu in your software application, click Print.
3.
Make sure the product is the selected printer.
4.
If you need to change settings, click the button that opens the Properties dialog box.
Depending on your software application, this button might be called Properties,
Options, Printer Setup, Printer, or Preferences.
NOTE:
When printing a photo, you must select options for the specific photo paper and photo enhancement.
Print documents 11
Chapter 4
5.
Select the appropriate options for your print job by using the features available in the
Advanced, Printing Shortcuts, Features, and Color tabs.
TIP:
You can easily select the appropriate options for your print job by choosing one of the predefined print tasks on the Printing Shortcuts tab. Click a type of print task in the Printing Shortcuts list. The default settings for that type of print task are set and summarized on the Printing Shortcuts tab. If necessary, you can adjust the settings here and save your custom settings as a new printing shortcut. To save a custom printing shortcut, select the shortcut and click Save
As. To delete a shortcut, select the shortcut and click Delete.
6.
Click OK to close the Properties dialog box.
7.
Click Print or OK to begin printing.
Related topics
•
Recommended papers for printing
•
•
•
Create custom printing shortcuts
•
Set the default print settings
•
Print photos
To print a photo on photo paper
1.
Remove all paper from the input tray, and then load the photo paper print side down.
12
2.
On the File menu in your software application, click Print.
3.
Make sure the product is the selected printer.
4.
Click the button that opens the Properties dialog box.
Depending on your software application, this button might be called Properties,
Options, Printer Setup, Printer, or Preferences.
5.
Click the Features tab.
6.
In the Basic Options area, select the appropriate photo paper type from the Paper
Type drop-down list.
7.
In the Resizing Options area, click the appropriate paper size from the Size list.
If the paper size and paper type are not compatible, the product software displays an alert and allows you to select a different type or size.
8.
In the Basic Options area, select a high print quality, such as Best, from the Print
Quality drop-down list.
NOTE:
For maximum dpi resolution, go to the Advanced tab, and then select
Enabled from the Maximum dpi drop-down list. For more information, see
.
9.
Click OK to return to the Properties dialog box.
10.
(Optional) If you want to print the photo in black and white, click the Color tab and select the Print in grayscale check box. From the drop-down list, select one of the following options:
• High Quality: uses all the available colors to print your photo in grayscale. This creates smooth and natural shades of gray.
• Black Ink Only: uses black ink to print your photo in grayscale. The gray shading is created by varying patterns of black dots, which might result in a grainy image.
11.
Click OK, and then click Print or OK in the Print dialog box.
NOTE:
Do not leave unused photo paper in the input tray. The paper might start to curl, which could reduce the quality of your printout. Photo paper should be flat before printing.
To print a borderless image
1.
Remove all paper from the input tray.
2.
Place the photo paper print side down on the right side of the input tray.
3.
On the File menu in your software application, click Print.
Print photos 13
Chapter 4
4.
Make sure the product is the selected printer.
5.
Click the button that opens the Properties dialog box.
Depending on your software application, this button might be called Properties,
Options, Printer Setup, Printer, or Preferences.
6.
Click the Features tab.
7.
In the Size list, click the size of photo paper loaded in the input tray.
If a borderless image can be printed on the specified size, the Borderless printing check box is enabled.
8.
In the Paper Type drop-down list, click More, and then select the appropriate paper type.
NOTE:
You cannot print a borderless image if the paper type is set to Plain
paper or to a type of paper other than a photo paper.
9.
Select the Borderless printing check box if it is not already checked.
If the borderless paper size and paper type are not compatible, the product software displays an alert and allows you to select a different type or size.
10.
Click OK, and then click Print or OK in the Print dialog box.
NOTE:
Do not leave unused photo paper in the input tray. The paper might start to curl, which could reduce the quality of your printout. Photo paper should be flat before printing.
Related topics
•
•
•
•
Create custom printing shortcuts
•
Set the default print settings
•
Print envelopes
You can load one or more envelopes into the input tray of the HP Printer. Do not use shiny or embossed envelopes or envelopes that have clasps or windows.
NOTE:
For specific details on how to format text for printing on envelopes, consult the help files in your word processing software. For best results, consider using a label for the return address on envelopes.
To print envelopes
1.
Slide the paper-width guide all the way to the left.
2.
Place the envelopes in the right side of the input tray. The side to be printed on should face down. The flap should be on the left side.
3.
Push the envelopes into the printer until they stop.
14 Print
4.
Slide the paper-width guide firmly against the edge of the envelopes.
5.
Open the Printer Properties dialog box.
6.
Click the Features tab, and then select the following print settings:
• Paper Type: Plain paper
• Size: An appropriate envelope size
7.
Select any other print settings that you want, and then click OK.
Related topics
•
•
•
Create custom printing shortcuts
•
Set the default print settings
•
Print on specialty media
Print transparencies
1.
Slide the paper-width guide all the way to the left.
2.
Place the transparencies in the right side of the input tray. The side to be printed should face down and the adhesive strip should face up and toward the printer.
3.
Carefully push the transparencies into the printer until they stop, so that the adhesive strips do not catch on one another.
4.
Slide the paper-width guide firmly against the edge of the transparencies.
5.
Open the Printer Properties dialog box.
Print on specialty media 15
Chapter 4
6.
Click the Printing Shortcuts tab.
7.
In the Printing Shortcuts list, click Presentation Printing, and then specify the following print settings:
• Paper Type: Click More, and then select an appropriate transparency film.
• Paper Size: An appropriate paper size
8.
Select any other print settings that you want, and then click OK.
Print postcards
1.
Slide the paper-width guide all the way to the left.
2.
Place the cards in the right side of the input tray. The side to be printed on should face down and the short edge should point toward the printer.
3.
Push the cards into the printer until they stop.
4.
Slide the paper-width guide firmly against the edge of the cards.
5.
Open the Printer Properties dialog box.
6.
Click the Features tab, and then specify the following print settings:
• Paper Type: Click More, click Specialty Papers, and then select an appropriate card type.
• Print Quality: Normal or Best
• Size: An appropriate card size
7.
Select any other print settings that you want, and then click OK.
Print labels
1.
Slide the paper-width guide all the way to the left.
2.
Fan the edges of the label sheets to separate them, and then align the edges.
3.
Place the label sheets in the right side of the input tray. The label side should face down.
4.
Push the sheets into the printer until they stop.
16 Print
5.
Slide the paper-width guide firmly against the edge of the sheets.
6.
Open the Printer Properties dialog box.
7.
Click the Printing Shortcuts tab.
8.
In the Printing Shortcuts list, click General Everyday Printing, and then specify the following print settings:
• Paper Type: Plain Paper
• Paper Size: An appropriate paper size
9.
Click OK.
Print brochures
1.
Slide the paper-width guide all the way to the left.
2.
Place the paper in the right side of the input tray. The side to be printed on should face down.
3.
Push the paper into the printer until it stops.
4.
Slide the paper-width guide firmly against the edge of the paper.
5.
Open the Printer Properties dialog box.
6.
Click the Features tab.
7.
Specify the following print settings:
• Print Quality: Best
• Paper Type: Click More, and then select an appropriate HP inkjet paper.
• Orientation: Portrait or Landscape
• Size: An appropriate paper size
• Two-sided printing: Manual
8.
Click OK to print.
Print on specialty media 17
Chapter 4
Print greeting cards
1.
Slide the paper-width guide all the way to the left.
2.
Fan the edges of the greeting cards to separate them, and then align the edges.
3.
Place the greeting cards in the right side of the input tray. The side to be printed on should face down.
4.
Push the cards into the printer until they stop.
5.
Slide the paper-width guide firmly against the edge of the cards.
6.
Open the Printer Properties dialog box.
7.
Click the Features tab, and then specify the following print settings:
• Print Quality: Normal
• Paper Type: Click More, and then select an appropriate card type.
• Size: An appropriate card size
8.
Select any other print settings that you want, and then click OK.
Print booklets
1.
Slide the paper-width guide all the way to the left.
2.
Place plain paper in the right side of the input tray. The side to be printed on should face down.
3.
Push the paper into the printer until it stops.
4.
Slide the paper-width guide firmly against the edge of the paper.
18 Print
5.
Open the Printer Properties dialog box.
6.
Click the Printing Shortcuts tab.
7.
In the Printing Shortcuts list, click Booklet Printing.
8.
In the Print On Both Sides drop-down list, select one of the following binding options:
•
Left Edge Booklet
•
Right Edge Booklet
9.
Select any other print settings that you want, and then click OK.
10.
When prompted, reload the printed pages in the input tray as shown below.
11.
Click Continue to finish printing the booklet.
Print posters
1.
Slide the paper-width guide all the way to the left.
2.
Place plain paper in the right side of the input tray. The side to be printed on should face down.
3.
Push the paper into the printer until it stops.
4.
Slide the paper-width guide firmly against the edge of the paper.
5.
Open the Printer Properties dialog box.
6.
Click the Features tab, and then specify the following print settings:
• Paper Type: Plain Paper
• Orientation: Portrait or Landscape
• Size: An appropriate paper size
7.
Click the Advanced tab, and then click Printer Features.
8.
In the Poster Printing drop-down list, select the number of sheets for the poster.
9.
Click the Select Tiles button.
Print on specialty media 19
Chapter 4
10.
Check that the number of tiles that are selected matches the number of sheets for the poster, and then click OK.
11.
Select any other print settings that you want, and then click OK.
Print iron-on transfers
1.
Slide the paper-width guide all the way to the left.
2.
Place the iron-on transfer paper in the right side of the input tray. The side to be printed on should face down.
3.
Push the paper into the printer until it stops.
4.
Slide the paper-width guide firmly against the edge of the paper.
5.
Open the Printer Properties dialog box.
20 Print
6.
Click the Features tab, and then specify the following print settings:
• Print Quality: Normal or Best
• Paper Type: Click More, click Specialty Papers, and then click Other specialty
paper.
• Size: An appropriate paper size
7.
Click the Advanced tab.
8.
Click Printer Features, and then set Mirror Image to On.
NOTE:
Some iron-on transfer software programs do not require you to print a mirror image.
9.
Select any other print settings that you want, and then click OK.
Related topics
•
Recommended papers for printing
•
•
•
Create custom printing shortcuts
•
Set the default print settings
•
Print a Web page
You can print a Web page from your Web browser on the HP Printer.
If you use Internet Explorer (6.0 or higher) or Firefox (2.0 or higher) for Web browsing, you can use HP Smart Web Printing to ensure simple, predictable web printing with control over what you want and how you want it printed. You can access HP Smart Web
Printing from the toolbar in Internet Explorer. For more information about HP Smart Web
Printing, see the help file provided with it.
To print a Web page
1.
Make sure you have paper loaded in the input tray.
2.
On the File menu in your Web browser, click Print.
TIP:
For best results, select HP Smart Web Printing on the File menu. A check mark appears when it is selected.
The Print dialog box appears.
3.
Make sure the product is the selected printer.
4.
If your Web browser supports it, select the items on the Web page that you want to include in the printout.
For example, in Internet Explorer, click the Options tab to select options such as As
laid out on screen, Only the selected frame, and Print all linked documents.
5.
Click Print or OK to print the Web page.
TIP:
To print Web pages correctly, you might need to set your print orientation to
Landscape.
Print a Web page 21
Chapter 4
Related topics
•
Recommended papers for printing
•
•
•
Create custom printing shortcuts
•
Set the default print settings
•
Print using the maximum dpi
Use maximum dpi mode to print high-quality, sharp images.
To get the most benefit from maximum dpi mode, use it to print high-quality images such as digital photographs. When you select the maximum dpi setting, the printer software displays the optimized dots per inch (dpi) that the HP Printer printer will print. Printing in maximum dpi is supported on the following paper-types only:
• HP Premium Plus Photo Paper
• HP Premium Photo Paper
• HP Advanced Photo Paper
• Photo Hagaki
Printing in maximum dpi takes longer than printing with other settings and requires a large amount of disk space.
To print in Maximum dpi mode
1.
Make sure you have paper loaded in the input tray.
2.
On the File menu in your software application, click Print.
3.
Make sure the product is the selected printer.
4.
Click the button that opens the Properties dialog box.
Depending on your software application, this button might be called Properties,
Options, Printer Setup, Printer, or Preferences.
5.
Click the Advanced tab.
6.
In the Features area, select the Maximum dpi check box.
7.
Click the Features tab.
8.
In the Paper Type drop-down list, click More, and then select the appropriate paper type.
9.
In the Print Quality drop-down list, click Maximum dpi.
NOTE:
To view the maximum dpi that the product will print, click Resolution.
10.
Select any other print settings that you want, and then click OK.
Related topics
22 Print
View the print resolution
The printer software displays the print resolution in dots per inch (dpi). The dpi varies according to the paper type and print quality that you select in the printer software.
To view the print resolution
1.
Make sure you have paper loaded in the input tray.
2.
On the File menu in your software application, click Print.
3.
Make sure the product is the selected printer.
4.
Click the button that opens the Properties dialog box.
Depending on your software application, this button might be called Properties,
Options, Printer Setup, Printer, or Preferences.
5.
Click the Features tab.
6.
In the Print Quality drop-down list, select the appropriate print quality setting for your project.
7.
In the Paper Type drop-down list, select the type of paper that you have loaded.
8.
Click the Resolution button to view the print resolution dpi.
Create custom printing shortcuts
Use printing shortcuts to print with print settings that you use often. The printer software has several specially designed printing shortcuts that are available in the Printing
Shortcuts list.
NOTE:
When you select a printing shortcut the appropriate printing options are automatically displayed. You can leave them as is, change them, or create your own shortcuts for commonly used tasks.
Use the Printing Shortcuts tab for the following print tasks:
• General Everyday Printing: Print documents quickly.
• Photo Printing–Borderless: Print to the top, bottom, and side edges of 10 x 15 cm
(4 x 6 inch) and 13 x 18 cm (5 x 7 inch) HP Photo Papers.
• Paper-saving Printing: Print two-sided documents with mutliple pages on same sheet to reduce paper usage.
• Photo Printing–With White Borders: Print a photo with a white border around the edges.
• Fast/Economical Printing: Produce draft-quality printouts quickly.
• Presentation Printing: Print high-quality documents, including letters and transparencies.
To create a printing shortcut
1.
On the File menu in your software application, click Print.
2.
Make sure the product is the selected printer.
3.
Click the button that opens the Properties dialog box.
Depending on your software application, this button might be called Properties,
Options, Printer Setup, Printer, or Preferences.
Create custom printing shortcuts 23
Chapter 4
4.
Click the Printing Shortcuts tab.
5.
In the Printing Shortcuts list, click a printing shortcut.
The print settings for the selected printing shortcut are displayed.
6.
Change the print settings to those you want in the new printing shortcut.
7.
Click Save as and type a name for the new printing shortcut, and then click Save.
The printing shortcut is added to the list.
To delete a printing shortcut
1.
On the File menu in your software application, click Print.
2.
Make sure the product is the selected printer.
3.
Click the button that opens the Properties dialog box.
Depending on your software application, this button might be called Properties,
Options, Printer Setup, Printer, or Preferences.
4.
Click the Printing Shortcuts tab.
5.
In the Printing Shortcuts list, click the printing shortcut that you want to delete.
6.
Click Delete.
The printing shortcut is removed from the list.
NOTE:
Only the shortcuts that you have created can be deleted. The original HP shortcuts cannot be deleted.
Set the default print settings
If there are settings that you frequently use for printing, you might want to make them the default print settings so they are already set when you open the Print dialog box from within your software application.
To change the default print settings
1.
In the HP Solution Center, click Settings, point to Print Settings, and then click
Printer Settings.
2.
Make changes to the print settings, and click OK.
24 Print
5 Paper basics
You can load many different types and sizes of paper in the HP Printer, including letter or A4 paper, photo paper, transparencies, and envelopes.
This section contains the following topics:
Recommended papers for printing
If you want the best print quality, HP recommends using HP papers that are specifically designed for the type of project you are printing.
Depending on your country/region, some of these papers might not be available.
HP Advanced Photo Paper
This thick photo paper features an instant-dry finish for easy handling without smudging.
It resists water, smears, fingerprints, and humidity. Your prints have a look and feel comparable to a store-processed photo. It is available in several sizes, including A4, 8.5
x 11 inch, 10 x 15 cm (4 x 6 inch) (with or without tabs), 13 x 18 cm (5 x 7 inch), and two finishes - glossy or soft gloss (satin matte). It is acid-free for longer lasting documents.
HP Everyday Photo Paper
Print colorful, everyday snapshots at a low cost, using paper designed for casual photo printing. This affordable, photo paper dries quickly for easy handling. Get sharp, crisp images when you use this paper with any inkjet printer. It is available in semi-gloss finish in several sizes, including A4, 8.5 x 11 inch, and 10 x 15 cm (4 x 6 inch) (with or without tabs). For longer-lasting photos, it is acid-free.
HP Brochure Paper or HP Superior Inkjet Paper
These papers are glossy-coated or matte-coated on both sides for two-sided use. They are the perfect choice for near-photographic reproductions and business graphics for report covers, special presentations, brochures, mailers, and calendars.
HP Premium Presentation Paper or HP Professional Paper
These papers are heavy two-sided matte papers perfect for presentation, proposals, reports, and newsletters. They are heavyweight for an impressive look and feel.
HP Bright White Inkjet Paper
HP Bright White Inkjet Paper delivers high-contrast colors and sharp text. It is opaque enough for two-sided color usage with no show-through, which makes it ideal for newsletters, reports, and flyers. It features ColorLok Technology for less smearing, bolder blacks, and vivid colors.
HP Printing Paper
HP Printing Paper is a high-quality multifunction paper. It produces documents that look and feel more substantial than documents printed on standard multipurpose or copy
Recommended papers for printing 25
Chapter 5 paper. It features ColorLok Technology for less smearing, bolder blacks, and vivid colors.
It is acid-free for longer lasting documents.
HP Office Paper
HP Office Paper is a high-quality multifunction paper. It is suitable for copies, drafts, memos, and other everyday documents. It features ColorLok Technology for less smearing, bolder blacks, and vivid colors. It is acid-free for longer lasting documents.
HP Iron-On Transfers
HP Iron-on Transfers (for color fabrics or for light or white fabrics) are the ideal solution for creating custom T-shirts from your digital photos.
HP Premium Inkjet Transparency Film
HP Premium Inkjet Transparency Film make your color presentations vivid and even more impressive. This film is easy to use and handle and dries quickly without smudging.
HP Photo Value Pack
HP Photo Value Packs conveniently package original HP cartridges and HP Advanced
Photo Paper to save you time and take the guesswork out of printing affordable professional photos with your HP Printer. Original HP inks and HP Advanced Photo
Paper have been designed to work together so your photos are long lasting and vivid, print after print. Great for printing out an entire vacation’s worth of photos or multiple prints to share.
ColorLok
HP recommends plain papers with the ColorLok logo for printing and copying of everyday documents. All papers with the ColorLok logo are independently tested to meet high standards of reliability and print quality, and produce documents with crisp, vivid color, bolder blacks, and dry faster than ordinary plain papers. Look for papers with the ColorLok logo in a variety of weights and sizes from major paper manufacturers.
NOTE:
At this time, some portions of the HP Web site are available in English only.
To order HP papers and other supplies, go to www.hp.com/buy/supplies . If prompted, choose your country/region, follow the prompts to select your product, and then click one of the shopping links on the page.
26 Paper basics
Load media
1.
Select a paper size to continue.
Load small-size paper
a. Prepare input tray.
❑ Slide paper-width guide to the left.
❑ Remove all paper from the input tray.
b. Load paper.
❑ Insert stack of photo paper into input tray with short edge forward and print side down.
❑ Slide stack of paper forward until it stops.
NOTE:
If the photo paper you are using has perforated tabs, load photo paper so that tabs are closest to you.
❑ Slide paper-width guide to the right until it stops at edge of paper.
Load media 27
Chapter 5
Load full-size paper
a. Prepare input tray.
❑ Slide paper-width guide to the left.
❑ Remove all paper from the input tray.
b. Load paper.
❑ Insert stack of paper into input tray with short edge forward and print side down.
❑ Slide stack of paper forward until it stops.
❑ Slide paper-width guide to the right until it stops at edge of paper.
Load envelopes
a. Prepare input tray.
❑ Slide paper-width guide to the left.
❑ Remove all paper from the input tray.
b. Load envelopes.
❑ Insert one or more envelopes into far-right side of the input tray, with envelope flaps on left and facing up.
❑ Slide stack of envelopes forward until it stops.
❑ Slide paper-width guide to the right against stack of envelopes until it stops.
2.
View the animation for this topic.
28 Paper basics
6 Work with cartridges
•
Check the estimated ink levels
•
•
•
Automatically clean print cartridges
•
Manually clean print cartridges
•
•
Cartridge warranty information
Check the estimated ink levels
You can easily check the ink supply level to determine how soon you might need to replace a cartridge. The ink supply level shows an estimate of the amount of ink remaining in the cartridges.
NOTE:
If you have installed a refilled or remanufactured cartridge, or a cartridge that has been used in another printer, the ink level indicator might be inaccurate or unavailable.
NOTE:
Ink level warnings and indicators provide estimates for planning purposes only. When you receive a low-ink warning message, consider having a replacement cartridge available to avoid possible printing delays. You do not have to replace the cartridges until the print quality is unacceptable.
NOTE:
Ink from the cartridges is used in the printing process in a number of different ways, including in the initialization process, which prepares the product and cartridges for printing, and in printhead servicing, which keeps print nozzles clear and ink flowing smoothly. In addition, some residual ink is left in the cartridge after it is used. For more information, see www.hp.com/go/inkusage .
To check the ink levels from the control panel
▲ Look for two icons at the bottom of the display that represent the levels of ink remaining in the installed print cartridges.
The color of the icon represents the type of print cartridge installed in the HP Printer.
Depending on which two print cartridges you have installed, the following icons will display:
• A green icon represents the tri-color print cartridge.
• A black icon represents the black print cartridge.
Check the estimated ink levels 29
Chapter 6
To check the ink levels from the HP Photosmart Software
1.
In the HP Solution Center, click Settings, point to Print Settings, and then click
Printer Toolbox.
NOTE:
You can also open the Printer Toolbox from the Print Properties dialog box. In the Print Properties dialog box, click the Features tab, and then click the
Printer Services button.
The Printer Toolbox appears.
2.
Click the Estimated Ink Level tab.
The estimated ink levels for the print cartridges appear.
Related topics
Order ink supplies
For a list of cartridge numbers, use the software that came with the HP Printer to find out the reorder number.
Find the cartridge number
1.
In the HP Solution Center, click Settings, point to Print Settings, and then click
Printer Toolbox.
NOTE:
You can also open the Printer Toolbox from the Print Properties dialog box. In the Print Properties dialog box, click the Features tab, and then click the
Printer Services button.
The Printer Toolbox appears.
2.
Click the Estimated Ink Level tab.
The estimated ink levels for the print cartridges appear. Use the menu at the bottom to select Cartridge details.
To order genuine HP supplies for the HP Printer, go to www.hp.com/buy/supplies . If prompted, choose your country/region, follow the prompts to select your product, and then click one of the shopping links on the page.
NOTE:
Ordering cartridges online is not supported in all countries/regions. If it is not available in your country/region, you may still view supplies information and print a list for reference when shopping at a local HP reseller.
30 Work with cartridges
To order ink cartridges from your desktop
▲ To learn which HP supplies work with your printer, order supplies online, or create a printable shopping list, open HP Solution Center and select the online shopping feature.
Cartridge information and links to online shopping also appear on ink alert messages.
In addition, you can find cartridge information and order online by visiting www.hp.com/buy/supplies .
NOTE:
Ordering cartridges online is not supported in all countries/regions. If it is not available in your country/region, you may still view supplies information and print a list for reference when shopping at a local HP reseller.
Related topics
Ink-backup mode
Use the ink-backup mode to operate the HP Printer with only one print cartridge. The inkbackup mode is initiated when a print cartridge is removed from the print cartridge carriage. During ink-backup mode, the product can only print jobs from the computer.
NOTE:
When the HP Printer operates in ink-backup mode, a message is displayed on screen. If the message is displayed and two print cartridges are installed in the product, verify that the protective piece of plastic tape has been removed from each print cartridge. When plastic tape covers the print cartridge contacts, the product cannot detect that the print cartridge is installed.
Ink-backup mode output
Printing in ink-backup mode slows the printer and affects the quality of printouts.
Installed print cartridge
Black print cartridge
Tri-color print cartridge
Result
Colors print as grayscale.
Colors print but black is grayed and is not a true black.
Exit ink-backup mode
Install two print cartridges in the HP Printer to exit ink-backup mode.
Related topics
Ink-backup mode 31
Chapter 6
Choose the right cartridges
HP recommends that you use original HP cartridges. Original HP cartridges are designed and tested with HP printers to help you easily produce great results, time after time.
Related topics
Automatically clean print cartridges
If your printed pages are faded or if they contain ink streaks, the print cartridges might be low on ink or might need to be cleaned. For more information, see
Check the estimated ink levels
.
If the print cartridges are not low on ink, clean the print cartridges automatically.
CAUTION:
Clean print cartridges only when necessary. Unnecessary cleaning wastes ink and shortens the life of the cartridge.
To clean the print cartridges
1.
In the HP Solution Center, click Settings. In the Print Settings area, click Printer
Toolbox.
2.
Click Clean the Print Cartridges.
3.
Click Clean, and then follow the onscreen instructions.
Manually clean print cartridges
You should manually clean the print cartridges only if you have received an error message related to the cartridges, such as 'Print cartridge missing or damaged'. The message should also indicate which cartridge is causing the problem. That is the only cartridge that you need to clean.
Make sure you have the following materials available:
• Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart or leave fibers.
TIP:
Coffee filters are lint-free and work well for cleaning print cartridges.
• Distilled, filtered, or bottled water (tap water might contain contaminants that can damage the print cartridges).
CAUTION:
Do not use platen cleaners or alcohol to clean the print cartridge contacts. These can damage the print cartridge or the product.
To clean the print cartridge contacts
1.
Turn on the product and open the print cartridge door.
The print carriage moves to the center of the product.
2.
Wait until the print carriage is idle and silent, and then unplug the power cord from the back of the product.
32 Work with cartridges
3.
Lightly press down on the print cartridge to release it, and then pull it towards you out of the slot.
NOTE:
Do not remove both print cartridges at the same time. Remove and clean each print cartridge one at a time. Do not leave a print cartridge outside the
HP Printer for more than 30 minutes.
4.
Inspect the print cartridge contacts for ink and debris buildup.
5.
Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze any excess water from it.
6.
Hold the print cartridge by its sides.
7.
Clean only the copper-colored contacts. Allow the print cartridges to dry for approximately ten minutes.
1 Copper-colored contacts
2 Ink nozzles (do not clean)
8.
Hold the print cartridge with the HP logo on top, and insert the print cartridge back into the slot. Make sure you push the print cartridge in firmly until it snaps into place.
Manually clean print cartridges 33
Chapter 6
9.
Repeat if necessary for the other print cartridge.
10.
Gently close the print cartridge door and plug the power cord into the back of the product.
Replace the cartridges
To replace the cartridges
1.
Check that power is on.
2.
Remove cartridge.
a. Open cartridge door.
Wait for print carriage to move to center of the product.
b. Press down to release cartridge, then remove it from slot.
34 Work with cartridges
3.
Insert new cartridge.
a. Remove cartridge from packaging.
b. Remove plastic tape using pink pull tab.
c. Line up colored shaped icons, then slide cartridge into slot until it clicks into place.
Replace the cartridges 35
Chapter 6
d. Close cartridge door.
4.
Align cartridges.
5.
View the animation for this topic.
Related topics
•
•
Cartridge warranty information
The HP cartridge warranty is applicable when the product is used in its designated HP printing device. This warranty does not cover HP ink products that have been refilled, remanufactured, refurbished, misused, or tampered with.
During the warranty period the product is covered as long as the HP ink is not depleted and the end of warranty date has not been reached. The end of warranty date, in YYYY/
MM/DD format, may be found on the product as indicated:
For a copy of the HP Limited Warranty Statement, see the printed documentation that came with the product.
36 Work with cartridges
7 Solve a problem
This section contains the following topics:
•
•
•
•
HP support
•
•
•
Support process
If you have a problem, follow these steps:
1.
Check the documentation that came with the product.
2.
Visit the HP online support Web site at www.hp.com/support . HP online support is available to all HP customers. It is the fastest source for up-to-date product information and expert assistance and includes the following features:
• Fast access to qualified online support specialists
• Software and driver updates for the product
• Valuable product and troubleshooting information for common problems
• Proactive product updates, support alerts, and HP newsgrams that are available when you register the product
3.
Call HP support. Support options and availability vary by product, country/region, and language.
HP support by phone
Phone support options and availability vary by product, country/region, and language.
This section contains the following topics:
•
•
•
•
After the phone support period
Phone support period
One year of phone support is available in North America, Asia Pacific, and Latin America
(including Mexico). To determine the duration of phone support in Europe, the Middle
East, and Africa, go to www.hp.com/support . Standard phone company charges apply.
HP support 37
Chapter 7
Placing a call
Call HP support while you are in front of the computer and the product. Be prepared to provide the following information:
• Product name (HP Deskjet D5500 Printer series)
• Serial number (located on the back or bottom of the product)
• Messages that appear when the situation occurs
• Answers to these questions:
◦ Has this situation happened before?
◦ Can you re-create it?
◦ Did you add any new hardware or software to your computer at about the time that this situation began?
◦ Did anything else occur prior to this situation (such as a thunderstorm, product was moved, etc.)?
Support phone numbers
For the most current HP list of telephone support numbers and call costs information, see www.hp.com/support .
After the phone support period
After the phone support period, help is available from HP at an additional cost. Help may also be available at the HP online support Web site: www.hp.com/support . Contact your
HP dealer or call the support phone number for your country/region to learn more about support options.
Additional warranty options
Extended service plans are available for the HP Printer at additional costs. Go to www.hp.com/support , select your country/region and language, then explore the services and warranty area for information about the extended service plans.
Setup troubleshooting
This section contains setup troubleshooting information for the product.
Many issues are caused when the product is connected to the computer using a USB cable before the HP Photosmart software is installed on the computer. If you connected the product to your computer before the software installation screen prompts you to do so, you must follow these steps:
Troubleshooting common setup issues
1.
Disconnect the USB cable from the computer.
2.
Uninstall the software (if you have already installed it).
For more information, see
Uninstall and reinstall the software .
3.
Restart your computer.
38 Solve a problem
4.
Turn off the product, wait one minute, then restart it.
5.
Reinstall the HP Photosmart software.
CAUTION:
Do not connect the USB cable to the computer until prompted by the software installation screen.
This section contains the following topics:
•
•
After setting up the product, it does not print
•
The registration screen does not appear
•
Uninstall and reinstall the software
The product will not turn on
Try the following solutions to resolve the issue. Solutions are listed in order, with the most likely solution first. If the first solution does not solve the problem, continue trying the remaining solutions until the issue is resolved.
•
Solution 1: Make sure the power cord is connected
•
Solution 2: Press the On button more slowly
Solution 1: Make sure the power cord is connected
Solution:
• Make sure the power cord is firmly connected to both the product and the power adapter. Plug the power cord into a power outlet, surge protector, or power strip.
1 Power connection
2 Power cord and adapter
• If you are using a power strip, make sure the power strip is on. Or, try plugging the product directly into a power outlet.
• Test the power outlet to make sure it is working. Plug in an appliance that you know works, and see if the appliance has power. If not, then there might be a problem with the power outlet.
• If you plugged the product into a switched outlet, make sure the outlet is switched on. If it is switched to on but still does not work, then there might be a problem with the power outlet.
Setup troubleshooting 39
Chapter 7
Cause: The product was not properly connected to a power supply.
If this did not solve the issue, try the next solution.
Solution 2: Press the On button more slowly
Solution: The product might not respond if you press the On button too quickly.
Press the On button once. It might take a few minutes for the product to turn on. If you press the On button again during this time, you might turn the product off.
CAUTION:
If the product still does not turn on, it might have a mechanical failure.
Unplug the product from the power outlet.
Contact HP support for service.
Go to: www.hp.com/support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
Cause: You pressed the On button too quickly.
After setting up the product, it does not print
Try the following solutions to resolve the issue. Solutions are listed in order, with the most likely solution first. If the first solution does not solve the problem, continue trying the remaining solutions until the issue is resolved.
•
Step 1: Press the On button to turn on the product
•
Step 2: Set your product as the default printer
•
Step 3: Check the connection between the product and computer
Step 1: Press the On button to turn on the product
Solution: Look at the On button located on the product. If it is not lit, the product is turned off. Make sure the power cord is firmly connected to the product and plugged into a power outlet. Press the On button to turn on the product.
Cause: The product might not have been turned on.
If this did not solve the issue, try the next solution.
Step 2: Set your product as the default printer
Solution: Use the system tools on your computer to change your product to be the default printer.
Cause: You sent the print job to the default printer, but this product was not the default printer.
If this did not solve the issue, try the next solution.
40 Solve a problem
Step 3: Check the connection between the product and computer
Solution: Check the connection between the product and computer.
Cause: The product and computer were not communicating with each other.
The registration screen does not appear
Solution: You can access the registration (Sign up now) screen from the Windows taskbar by clicking Start, pointing to Programs or All Programs, HP, Deskjet D5500
series, and then clicking Product Registration.
Cause: The registration screen did not launch automatically.
Uninstall and reinstall the software
If your installation is incomplete, or if you connected the USB cable to the computer before prompted by the software installation screen, you might need to uninstall and then reinstall the software. Do not simply delete the HP Printer application files from your computer. Make sure to remove them properly using the uninstall utility provided when you installed the software that came with the HP Printer.
To uninstall and reinstall the software
1.
On the Windows taskbar, click Start, Settings, Control Panel (or just Control
Panel).
2.
Double-click Add/Remove Programs (or click Uninstall a program).
3.
Select HP Photosmart All-In-One Driver Software, and then click Change/
Remove.
Follow the onscreen instructions.
4.
Disconnect the product from your computer.
5.
Restart your computer.
NOTE:
It is important that you disconnect the product before restarting your computer. Do not connect the product to your computer until after you have reinstalled the software.
6.
Insert the product CD-ROM into your computer’s CD-ROM drive and then start the
Setup program.
NOTE:
If the Setup program does not appear, locate the setup.exe file on the
CD-ROM drive and double-click it.
NOTE:
If you no longer have the installation CD, you can download the software from www.hp.com/support .
7.
Follow the onscreen instructions and the instructions provided in the printed documentation that came with the product.
Setup troubleshooting 41
Chapter 7
When the software installation is complete, the HP Digital Imaging Monitor icon appears in the Windows system tray.
Print troubleshooting
Try the following solutions to resolve the issue. Solutions are listed in order, with the most likely solution first. If the first solution does not solve the problem, continue trying the remaining solutions until the issue is resolved.
•
•
•
•
•
•
Check cartridges
Try the following solutions.
•
Step 1: Make sure you are using genuine HP ink cartridges
•
Step 1: Make sure you are using genuine HP ink cartridges
Solution: Check to see if your ink cartridges are genuine HP ink cartridges.
HP recommends that you use genuine HP ink cartridges. Genuine HP ink cartridges are designed and tested with HP printers to help you easily produce great results, time after time.
NOTE:
HP cannot guarantee the quality or reliability of non-HP supplies. Product service or repairs required as a result of using a non-HP supply will not be covered under warranty.
If you believe you purchased genuine HP ink cartridges, go to: www.hp.com/go/anticounterfeit
Cause: Non-HP ink cartridges were being used.
42 Solve a problem
If this did not solve the issue, try the next solution.
Step 2: Check the ink levels
Solution: Check the estimated ink levels in the cartridges.
NOTE:
Ink level warnings and indicators provide estimates for planning purposes only. When you receive a low-ink warning message, consider having a replacement cartridge available to avoid possible printing delays. You do not need to replace the cartridges until print quality becomes unacceptable.
For more information, see:
Check the estimated ink levels
Cause: The ink cartridges might have insufficient ink.
If this did not solve the issue, try the next solution.
Check paper
Try the following solutions.
•
Step 1: Make sure only one type of paper is loaded
•
Step 2: Load the stack of paper correctly
Step 1: Make sure only one type of paper is loaded
Solution: Load only one type of paper at a time.
Cause: More than one type of paper was loaded in the input tray.
If this did not solve the issue, try the next solution.
Step 2: Load the stack of paper correctly
Solution: Remove the stack of paper from the input tray, reload the paper, and then slide the paper width guide inward until it stops at the edge of the paper.
For more information, see:
Cause: The paper-width guide was not positioned correctly.
Check product
Try the following solutions.
•
Solution 1: Align the print cartridges
•
Solution 2: Automatically clean the print cartridges.
Print troubleshooting 43
Chapter 7
Solution 1: Align the print cartridges
Solution: Aligning the print cartridges can help ensure high-quality output.
To align the print cartridges from the HP Photosmart Software
1.
Load letter or A4 unused plain white paper into the paper tray.
2.
In the HP Solution Center, click Settings.
3.
In the Print Settings area, click Printer Toolbox.
NOTE:
You can also open the Printer Toolbox from the Print Properties dialog box. In the Print Properties dialog box, click the Features tab, and then click Printer Services.
The Printer Toolbox appears.
4.
Click the Device Services tab.
5.
Click Align the Print Cartridges.
6.
Click Align, and then follow the onscreen instructions.
The HP Printer prints a test page, aligns the print cartridges, and calibrates the printer. Recycle or discard the test page.
Cause: The printer needed to be aligned.
If this did not solve the issue, try the next solution.
Solution 2: Automatically clean the print cartridges.
Solution: Clean the print cartridges.
For more information, see
Automatically clean print cartridges
Cause: The print cartridge nozzles needed to be cleaned.
If this did not solve the issue, try the next solution.
Check printer settings
Try the following solutions.
•
Step 1: Check the print settings
•
Step 2: Verify the paper size setting
•
Step 3: Check the printer margins
44 Solve a problem
Step 1: Check the print settings
Solution: Check the print settings.
• Check the print settings to see if the color settings are incorrect.
For example, check to see if the document is set to print in grayscale. Or, check to see if advanced color settings such as saturation, brightness, or color tone, are set to modify the appearance of colors.
• Check the print quality setting and make sure it matches the type of paper loaded in the product.
You might need to choose a lower print quality setting, if colors are running into each other. Or, choose a higher setting if you are printing a high-quality photo, and then make sure photo paper such as HP Advanced Photo Paper, is loaded in the input tray.
NOTE:
On some computer screens, colors might appear differently than they do when printed on paper. In this case, there is nothing wrong with the product, print settings, or ink cartridges. No further troubleshooting is required.
Cause: The print settings were set incorrectly.
If this did not solve the issue, try the next solution.
Step 2: Verify the paper size setting
Solution: Verify that you have selected the proper paper size setting for your project. Make sure that you have loaded the correct paper size in the input tray.
Cause: The paper size setting might not have been set correctly for the project you were printing.
If this did not solve the issue, try the next solution.
Step 3: Check the printer margins
Solution: Check the printer margins.
Make sure the margin settings for the document do not exceed the printable area of the product.
To check your margin settings
1.
Preview your print job before sending it to the product.
In most software applications, click the File menu, and then click Print Preview.
2.
Check the margins.
The product uses the margins you have set in your software application, as long as they are greater than the minimum margins the product supports. For more information about setting margins in your software application, see the documentation that came with the software.
3.
Cancel the print job if the margins are not satisfactory, and then adjust the margins in your software application.
Cause: The margins were not set correctly in your software application.
Print troubleshooting 45
Chapter 7
If this did not solve the issue, try the next solution.
Reset the product
Solution: Turn off the product, and then unplug the power cord. Plug the power cord back in, and then press the On button to turn on the product.
Cause: The product experienced an error.
If this did not solve the issue, try the next solution.
Contact HP support
Solution: Contact HP support for service.
Go to: www.hp.com/support .
If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
Cause: The ink cartridges were not intended for use in this product.
Errors
This section contains the following categories of messages about your product:
•
•
•
Wireless indicator lights
The wireless indicator icons on the product flash in special sequences to inform you about various error conditions. Refer to the following table for information on solving your error condition based on which icons are on or flashing on the product.
NOTE:
Wireless signal icon represents the wireless signal strength. Fewer signal bars indicate lower signal strength.
Table 7-1 Wireless indicator lights
Wireless button light
Wireless antenna icon
Wireless signal strength icon
Wireless error icon
Error light Description Solution
On On None Off Off The wireless
Wait for product to connect to
46 Solve a problem
Wireless indicator lights (continued)
On
On
On
On
Blinking
Blinking
Blinking
On
On
On
Blinking
On
Off
Off
None
Cycling through signal bars
Signal bars displayed
None
Cycling through signal bars
None
None
Off
Off
Off
Blinking
Off
Off
Off
Off
Off
Off
Fast blinking
Fast blinking
Fast blinking
Fast blinking
Wireless
Protected
Setup
(WPS) in progress.
Wireless
Protected
Setup
(WPS) progress error.
Session overlap detected during radio is turned on.
The product cannot connect to a wireless network.
The product is searching for available wireless networks.
The product is connected to a wireless network.
Wireless connection error.
The product can now print wirelessly.
Press the
Wireless
button to turn it off and clear the error.
Wait for product to connect to an access point.
Press the
Wireless
button to turn it off and clear the error.
Press the
Wireless
button to turn it off an access point.
1.
Check if the wireles s router or access point is turned on.
2.
Move the produc t closer to the wireles s router or access point.
Wait for product to connect to an access point.
Errors 47
Chapter 7
Wireless indicator lights (continued)
On On Signal bars displayed
Off Off
Wireless
Protected
Setup
(WPS).
Wireless
Protected
Setup
(WPS) successful.
and clear the error.
The product can now print wirelessly.
Flashing lights
The lights on the product flash in special sequences to inform you about various error conditions. Refer to the following table for information on solving your error condition based on which lights are on or flashing on the product.
Table 7-2 Flashing lights
On light Ink level indicator
Off Off
Resume light Error light
Blinking
Fast blinking for 3 seconds
Current ink levels
On
On
On
Current ink levels
Current ink levels
Current ink levels
Both fast blinking
Description Solution
Off
Off
Off
Fast blinking
Off
Off
Off
Off
Off
Off
The product is turned off.
The product is processing a job.
The product is processing a job or it is in an error state, other than a print cartridge error.
The product is out of paper.
The product has a paper jam.
Press the
On button to turn the product on.
Wait for the product to finish.
Wait for the product to complete the job before initiating a new job.
Fast blinking The front
Fast blinking access door or the print cartridge access door is open.
The print cartridges are missing or not
Load paper and press
Resume.
Clear the paper jam, and then press
Resume.
Close the front access door or the print cartridge access door.
Install or remove and reinsert print cartridges.
48 Solve a problem
Flashing lights (continued)
On Fourth tricolor print cartridge indicator light fast blinking
Off
On Tri-color print cartridge error indicator light fast blinking
Black print cartridge light on
Off
Off seated correctly.
The print cartridge might be defective.
The tape was not removed from one or both print cartridges.
The print cartridge is not intended for use in this product.
The tri-color print cartridge is getting low on ink.
Fast blinking The tri-color print cartridge is missing or not seated correctly or inserted in the wrong slot.
The tri-color print cartridge may be defective.
The tri-color print cartridge has been removed.
Replace the tri-color print cartridge when print quality is no longer acceptable.
Replace the tri-color print cartridge, or print in inkbackup mode with the black print cartridge.
For more information, see
.
Remove the print cartridge, remove tape, and reinsert the print cartridge.
The print cartridge might not be supported for use in the product. For more information about compatible print cartridges, see
Install or remove and reinsert the tri-color print cartridge.
Remove the tri-color print cartridge, remove tape, and reinsert the print cartridge.
Errors 49
Chapter 7
Flashing lights (continued)
On Fourth black print cartridge indicator light fast blinking
Off
On
On
Black print cartridge error indicator light fast blinking
Tri–color print cartridge light on
Both fast blinking
Off
Off
Off
The tape was not removed from the tricolor print cartridge.
The black print cartridge is getting low on ink.
Fast blinking The black print cartridge is missing or not seated correctly or inserted in the wrong slot.
The black print cartridge may be defective.
The black print cartridge has been removed.
The tape was not removed from the black print cartridge.
Fast blinking The tri-color or black print cartridge may be incompatible.
The tri-color or black print cartridge may be defective.
Replace the black print cartridge when print quality is no longer acceptable.
Replace the black print cartridge, or print in inkbackup mode with the tri-color print cartridge.
For more information, see
.
Install or remove and reinsert the black print cartridge.
Remove the black print cartridge, remove tape, and reinsert the print cartridge.
Replace with compatible tri-color or
50 Solve a problem
Flashing lights (continued)
On Both fast blinking
Off Fast blinking The print carriage is stalled.
black print cartridges.
1.
Remove black print
.
cartridge
2.
Close door.
3.
If the tricolor print cartridge light is still blinking, replace the tricolor print cartridge
. If the tricolor print cartridge light is not blinking, replace the black print
.
cartridge
NOTE:
You can also clean the print cartridges manually before replacing them. For more information,
see Manually clean print cartridges .
Open the front access door, and clear the carriage jam.
Press any button except the
On button.
Pressing the
On button
Errors 51
Chapter 7
Flashing lights (continued)
Fast blinking Both fast blinking
Fast blinking Fast blinking The product has a fatal error.
will turn off the product.
1.
Turn off the product.
2.
Unplug the power cord.
3.
Wait a minute, then plug the power cord back in.
4.
Turn on the product.
If the problem persists, contact HP
Support.
Printing in ink-backup mode
Solution: If you receive the ink-backup mode message and two print cartridges are installed in the product, verify that the protective piece of plastic tape has been removed from each print cartridge. When plastic tape covers the print cartridge contacts, the product cannot detect that the print cartridge is installed.
1 Copper-colored contacts
2 Plastic tape with pink pull tab (must be removed before installing)
3 Ink nozzles under tape
Cause: When the product detected that only one print cartridge is installed, inkbackup mode is initiated. This printing mode lets you print with a single print cartridge, but it slows the product and affects the quality of printouts.
52 Solve a problem
8 Stop the current job
To stop a print job from the HP Printer
▲ Press Cancel on the control panel. If the print job does not stop, press Cancel again.
It can take a few moments for printing to be cancelled.
Stop the current job 53
Chapter 8
54 Stop the current job
9 Technical information
The technical specifications and international regulatory information for the HP Printer are provided in this section.
For additional specifications, see the printed documentation that came with the HP Printer.
This section contains the following topics:
•
•
•
Environmental product stewardship program
•
•
Regulatory wireless statements
Notice
Hewlett-Packard Company notices
The information contained in this document is subject to change without notice.
All rights reserved. Reproduction, adaptation, or translation of this material is prohibited without prior written permission of Hewlett-Packard, except as allowed under copyright laws. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
© 2009 Hewlett-Packard Development Company, L.P.
Windows, Windows 2000, and Windows XP are U.S. registered trademarks of Microsoft Corporation.
Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
Specifications
Technical specifications for the HP Printer are provided in this section. For complete product specifications, see the Product Data Sheet at www.hp.com/support .
System requirements
Software and system requirements are located in the Readme file.
For information about future operating system releases and support, visit the HP online support Web site at www.hp.com/support .
Environmental specifications
• Recommended operating temperature range: 15 ºC to 32 ºC (59 ºF to 90 ºF)
• Allowable operating temperature range: 5 ºC to 40 ºC (41 ºF to 104 ºF)
• Humidity: 15% to 80% RH non-condensing; 28 ºC maximum dewpoint
• Non-operating (Storage) temperature range: –40 ºC to 60 ºC (–40 ºF to 140 ºF)
• In the presence of high electromagnetic fields, it is possible the output from the HP Printer may be slightly distorted
• HP recommends using a USB cable less than or equal to 3 m (10 feet) in length to minimize injected noise due to potential high electromagnetic fields
Input tray capacity
Plain paper sheets: Up to 80
Paper size
For a complete list of supported media sizes, see the printer software.
Specifications 55
Chapter 9
Paper weights
Letter Paper: 75 to 90 g/m² (20 to 24 lb)
Legal Paper: 75 to 90 g/m² (20 to 24 lb)
Envelopes: 75 to 90 g/m² (20 to 24 lb)
Cards: Up to 200 g/m² (110-lb index maximum)
Photo Paper: Up to 280 g/m² (75-lb index maximum)
Print resolution
Cartridge yield
Visit www.hp.com/go/learnaboutsupplies for more information on estimated cartridge yields.
Acoustic information
If you have Internet access, you can get acoustic information from the HP Web site. Go to: www.hp.com/support .
Environmental product stewardship program
Hewlett-Packard is committed to providing quality products in an environmentally sound manner.
Design for recycling has been incorporated into this product. The number of materials has been kept to a minimum while ensuring proper functionality and reliability. Dissimilar materials have been designed to separate easily. Fasteners and other connections are easy to locate, access, and remove using common tools. High priority parts have been designed to access quickly for efficient disassembly and repair.
For more information, visit HP’s Commitment to the Environment Web site at: www.hp.com/hpinfo/globalcitizenship/environment/index.html
This section contains the following topics:
•
•
•
•
•
•
HP inkjet supplies recycling program
•
•
Disposal of waste equipment by users in private households in the European Union
•
•
Toxic and hazardous substance table
Eco-Tips
HP is committed to helping customers reduce their environmental footprint. HP has provided the
Eco-Tips below to help you focus on ways to assess and reduce the impact of your printing choices.
In addition to specific features in this product, please visit the HP Eco Solutions web site for more information on HP’s environmental initiatives.
56 Technical information
www.hp.com/hpinfo/globalcitizenship/environment/
Your product's Eco features
• Smart Web printing: The HP Smart Web Printing interface includes a Clip Book and Edit
Clips window where you can store, organize, or print clips you have gathered from the Web.
For more information, see
• Energy Savings information: To determine the ENERGY STAR® qualification status for this product, see
• Recycled Materials: For more information regarding recycling of HP products, please visit: www.hp.com/hpinfo/globalcitizenship/environment/recycle/
Paper use
This product is suited for the use of recycled paper according to DIN 19309 and EN 12281:2002.
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance the ability to identify plastics for recycling purposes at the end of product life.
Material safety data sheets
Material safety data sheets (MSDS) can be obtained from the HP Web site at: www.hp.com/go/msds
Recycling program
HP offers an increasing number of product return and recycling programs in many countries/regions, and partners with some of the largest electronic recycling centers throughout the world. HP conserves resources by reselling some of its most popular products. For more information regarding recycling of HP products, please visit: www.hp.com/hpinfo/globalcitizenship/environment/recycle/
HP inkjet supplies recycling program
HP is committed to protecting the environment. The HP Inkjet Supplies Recycling Program is available in many countries/regions, and lets you recycle used print cartridges and ink cartridges free of charge. For more information, go to the following Web site: www.hp.com/hpinfo/globalcitizenship/environment/recycle/
Power consumption
Power usage drops significantly while in Sleep mode, which saves natural resources and saves money without affecting the high performance of this product. To determine the ENERGY STAR® qualification status for this product see the Product Data Sheet or Specifications Sheet. Qualified products are also listed at www.hp.com/go/energystar .
Environmental product stewardship program 57
Chapter 9
Disposal of waste equipment by users in private households in the European Union
Disposal of Waste Equipment by Users in Private Households in the European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Évacuation des équipements usagés par les utilisateurs dans les foyers privés au sein de l'Union européenne
La présence de ce symbole sur le produit ou sur son emballage indique que vous ne pouvez pas vous débarrasser de ce produit de la même façon que vos déchets courants.
Au contraire, vous êtes responsable de l'évacuation de vos équipements usagés et, à cet effet, vous êtes tenu de les remettre à un point de collecte agréé pour le recyclage des
équipements électriques et électroniques usagés. Le tri, l'évacuation et le recyclage séparés de vos équipements usagés permettent de préserver les ressources naturelles et de s'assurer que ces équipements sont recyclés dans le respect de la santé humaine et de l'environnement. Pour plus d'informations sur les lieux de collecte des équipements usagés, veuillez contacter votre mairie, votre service de traitement des déchets ménagers ou le magasin où vous avez acheté le produit.
Entsorgung von Elektrogeräten durch Benutzer in privaten Haushalten in der EU
Dieses Symbol auf dem Produkt oder dessen Verpackung gibt an, dass das Produkt nicht zusammen mit dem Restmüll entsorgt werden darf. Es obliegt daher Ihrer Verantwortung, das
Gerät an einer entsprechenden Stelle für die Entsorgung oder Wiederverwertung von Elektrogeräten aller Art abzugeben (z.B. ein Wertstoffhof). Die separate Sammlung und das
Recyceln Ihrer alten Elektrogeräte zum Zeitpunkt ihrer Entsorgung trägt zum Schutz der Umwelt bei und gewährleistet, dass sie auf eine Art und Weise recycelt werden, die keine
Gefährdung für die Gesundheit des Menschen und der Umwelt darstellt. Weitere Informationen darüber, wo Sie alte Elektrogeräte zum Recyceln abgeben können, erhalten Sie bei den örtlichen Behörden, Wertstoffhöfen oder dort, wo Sie das Gerät erworben haben.
Smaltimento di apparecchiature da rottamare da parte di privati nell'Unione Europea
Questo simbolo che appare sul prodotto o sulla confezione indica che il prodotto non deve essere smaltito assieme agli altri rifiuti domestici. Gli utenti devono provvedere allo smaltimento delle apparecchiature da rottamare portandole al luogo di raccolta indicato per il riciclaggio delle apparecchiature elettriche ed elettroniche. La raccolta e il riciclaggio separati delle apparecchiature da rottamare in fase di smaltimento favoriscono la conservazione delle risorse naturali e garantiscono che tali apparecchiature vengano rottamate nel rispetto dell'ambiente e della tutela della salute. Per ulteriori informazioni sui punti di raccolta delle apparecchiature da rottamare, contattare il proprio comune di residenza, il servizio di smaltimento dei rifiuti locale o il negozio presso il quale è stato acquistato il prodotto.
Eliminación de residuos de aparatos eléctricos y electrónicos por parte de usuarios domésticos en la Unión Europea
Este símbolo en el producto o en el embalaje indica que no se puede desechar el producto junto con los residuos domésticos. Por el contrario, si debe eliminar este tipo de residuo, es responsabilidad del usuario entregarlo en un punto de recogida designado de reciclado de aparatos electrónicos y eléctricos. El reciclaje y la recogida por separado de estos residuos en el momento de la eliminación ayudará a preservar recursos naturales y a garantizar que el reciclaje proteja la salud y el medio ambiente. Si desea información adicional sobre los lugares donde puede dejar estos residuos para su reciclado, póngase en contacto con las autoridades locales de su ciudad, con el servicio de gestión de residuos domésticos o con la tienda donde adquirió el producto.
Likvidace vysloužilého zařízení uživateli v domácnosti v zemích EU
Tato značka na produktu nebo na jeho obalu označuje, že tento produkt nesmí být likvidován prostým vyhozením do běžného domovního odpadu. Odpovídáte za to, že vysloužilé zařízení bude předáno k likvidaci do stanovených sběrných míst určených k recyklaci vysloužilých elektrických a elektronických zařízení. Likvidace vysloužilého zařízení samostatným sběrem a recyklací napomáhá zachování přírodních zdrojů a zajišťuje, že recyklace proběhne způsobem chránícím lidské zdraví a životní prostředí. Další informace o tom, kam můžete vysloužilé zařízení předat k recyklaci, můžete získat od úřadů místní samosprávy, od společnosti provádějící svoz a likvidaci domovního odpadu nebo v obchodě, kde jste produkt zakoupili.
Bortskaffelse af affaldsudstyr for brugere i private husholdninger i EU
Dette symbol på produktet eller på dets emballage indikerer, at produktet ikke må bortskaffes sammen med andet husholdningsaffald. I stedet er det dit ansvar at bortskaffe affaldsudstyr ved at aflevere det på dertil beregnede indsamlingssteder med henblik på genbrug af elektrisk og elektronisk affaldsudstyr. Den separate indsamling og genbrug af dit affaldsudstyr på tidspunktet for bortskaffelse er med til at bevare naturlige ressourcer og sikre, at genbrug finder sted på en måde, der beskytter menneskers helbred samt miljøet. Hvis du vil vide mere om, hvor du kan aflevere dit affaldsudstyr til genbrug, kan du kontakte kommunen, det lokale renovationsvæsen eller den forretning, hvor du købte produktet.
Afvoer van afgedankte apparatuur door gebruikers in particuliere huishoudens in de Europese Unie
Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden afgevoerd met het huishoudelijk afval. Het is uw verantwoordelijkheid uw afgedankte apparatuur af te leveren op een aangewezen inzamelpunt voor de verwerking van afgedankte elektrische en elektronische apparatuur. De gescheiden inzameling en verwerking van uw afgedankte apparatuur draagt bij tot het sparen van natuurlijke bronnen en tot het hergebruik van materiaal op een wijze die de volksgezondheid en het milieu beschermt. Voor meer informatie over waar u uw afgedankte apparatuur kunt inleveren voor recycling kunt u contact opnemen met het gemeentehuis in uw woonplaats, de reinigingsdienst of de winkel waar u het product hebt aangeschaft.
Eramajapidamistes kasutuselt kõrvaldatavate seadmete käitlemine Euroopa Liidus
Kui tootel või toote pakendil on see sümbol, ei tohi seda toodet visata olmejäätmete hulka. Teie kohus on viia tarbetuks muutunud seade selleks ettenähtud elektri- ja elektroonikaseadmete utiliseerimiskohta. Utiliseeritavate seadmete eraldi kogumine ja käitlemine aitab säästa loodusvarasid ning tagada, et käitlemine toimub inimeste tervisele ja keskkonnale ohutult.
Lisateavet selle kohta, kuhu saate utiliseeritava seadme käitlemiseks viia, saate küsida kohalikust omavalitsusest, olmejäätmete utiliseerimispunktist või kauplusest, kust te seadme ostsite.
Hävitettävien laitteiden käsittely kotitalouksissa Euroopan unionin alueella
Tämä tuotteessa tai sen pakkauksessa oleva merkintä osoittaa, että tuotetta ei saa hävittää talousjätteiden mukana. Käyttäjän velvollisuus on huolehtia siitä, että hävitettävä laite toimitetaan sähkö- ja elektroniikkalaiteromun keräyspisteeseen. Hävitettävien laitteiden erillinen keräys ja kierrätys säästää luonnonvaroja. Näin toimimalla varmistetaan myös, että kierrätys tapahtuu tavalla, joka suojelee ihmisten terveyttä ja ympäristöä. Saat tarvittaessa lisätietoja jätteiden kierrätyspaikoista paikallisilta viranomaisilta, jäteyhtiöiltä tai tuotteen jälleenmyyjältä.
Απόρριψη άχρηστων συσκευών στην Ευρωπαϊκή Ένωση
Το παρόν σύμβολο στον εξοπλισμό ή στη συσκευασία του υποδεικνύει ότι το προϊόν αυτό δεν πρέπει να πεταχτεί μαζί με άλλα οικιακά απορρίμματα. Αντίθετα, ευθύνη σας είναι να
απορρίψετε τις άχρηστες συσκευές σε μια καθορισμένη μονάδα συλλογής απορριμμάτων για την ανακύκλωση άχρηστου ηλεκτρικού και ηλεκτρονικού εξοπλισμού. Η χωριστή συλλογή και
ανακύκλωση των άχρηστων συσκευών θα συμβάλει στη διατήρηση των φυσικών πόρων και στη διασφάλιση ότι θα ανακυκλωθούν με τέτοιον τρόπο, ώστε να προστατεύεται η υγεία των
ανθρώπων και το περιβάλλον. Για περισσότερες πληροφορίες σχετικά με το πού μπορείτε να απορρίψετε τις άχρηστες συσκευές για ανακύκλωση, επικοινωνήστε με τις κατά τόπους αρμόδιες
αρχές ή με το κατάστημα από το οποίο αγοράσατε το προϊόν.
A hulladékanyagok kezelése a magánháztartásokban az Európai Unióban
Ez a szimbólum, amely a terméken vagy annak csomagolásán van feltüntetve, azt jelzi, hogy a termék nem kezelhető együtt az egyéb háztartási hulladékkal. Az Ön feladata, hogy a készülék hulladékanyagait eljuttassa olyan kijelölt gyűjtőhelyre, amely az elektromos hulladékanyagok és az elektronikus berendezések újrahasznosításával foglalkozik.
A hulladékanyagok elkülönített gyűjtése és újrahasznosítása hozzájárul a természeti erőforrások megőrzéséhez, egyúttal azt is biztosítja, hogy a hulladék újrahasznosítása az egészségre és a környezetre nem ártalmas módon történik. Ha tájékoztatást szeretne kapni azokról a helyekről, ahol leadhatja újrahasznosításra a hulladékanyagokat, forduljon a helyi önkormányzathoz, a háztartási hulladék begyűjtésével foglalkozó vállalathoz vagy a termék forgalmazójához.
Lietotāju atbrīvošanās no nederīgām ierīcēm Eiropas Savienības privātajās mājsaimniecībās
Šis simbols uz ierīces vai tās iepakojuma norāda, ka šo ierīci nedrīkst izmest kopā ar pārējiem mājsaimniecības atkritumiem. Jūs esat atbildīgs par atbrīvošanos no nederīgās ierīces, to nododot norādītajā savākšanas vietā, lai tiktu veikta nederīgā elektriskā un elektroniskā aprīkojuma otrreizējā pārstrāde. Speciāla nederīgās ierīces savākšana un otrreizējā pārstrāde palīdz taupīt dabas resursus un nodrošina tādu otrreizējo pārstrādi, kas sargā cilvēku veselību un apkārtējo vidi. Lai iegūtu papildu informāciju par to, kur otrreizējai pārstrādei var nogādāt nederīgo ierīci, lūdzu, sazinieties ar vietējo pašvaldību, mājsaimniecības atkritumu savākšanas dienestu vai veikalu, kurā iegādājāties šo ierīci.
Europos Sąjungos vartotojų ir privačių namų ūkių atliekamos įrangos išmetimas
Šis simbolis ant produkto arba jo pakuotės nurodo, kad produktas negali būti išmestas kartu su kitomis namų ūkio atliekomis. Jūs privalote išmesti savo atliekamą įrangą atiduodami ją į atliekamos elektronikos ir elektros įrangos perdirbimo punktus. Jei atliekama įranga bus atskirai surenkama ir perdirbama, bus išsaugomi natūralūs ištekliai ir užtikrinama, kad įranga yra perdirbta žmogaus sveikatą ir gamtą tausojančiu būdu. Dėl informacijos apie tai, kur galite išmesti atliekamą perdirbti skirtą įrangą kreipkitės į atitinkamą vietos tarnybą, namų ūkio atliekų išvežimo tarnybą arba į parduotuvę, kurioje pirkote produktą.
Utylizacja zużytego sprzętu przez użytkowników domowych w Unii Europejskiej
Symbol ten umieszczony na produkcie lub opakowaniu oznacza, że tego produktu nie należy wyrzucać razem z innymi odpadami domowymi. Użytkownik jest odpowiedzialny za dostarczenie zużytego sprzętu do wyznaczonego punktu gromadzenia zużytych urządzeń elektrycznych i elektronicznych. Gromadzenie osobno i recykling tego typu odpadów przyczynia się do ochrony zasobów naturalnych i jest bezpieczny dla zdrowia i środowiska naturalnego. Dalsze informacje na temat sposobu utylizacji zużytych urządzeń można uzyskać u odpowiednich władz lokalnych, w przedsiębiorstwie zajmującym się usuwaniem odpadów lub w miejscu zakupu produktu.
Descarte de equipamentos por usuários em residências da União Européia
Este símbolo no produto ou na embalagem indica que o produto não pode ser descartado junto com o lixo doméstico. No entanto, é sua responsabilidade levar os equipamentos a serem descartados a um ponto de coleta designado para a reciclagem de equipamentos eletro-eletrônicos. A coleta separada e a reciclagem dos equipamentos no momento do descarte ajudam na conservação dos recursos naturais e garantem que os equipamentos serão reciclados de forma a proteger a saúde das pessoas e o meio ambiente. Para obter mais informações sobre onde descartar equipamentos para reciclagem, entre em contato com o escritório local de sua cidade, o serviço de limpeza pública de seu bairro ou a loja em que adquiriu o produto.
Postup používateľov v krajinách Európskej únie pri vyhadzovaní zariadenia v domácom používaní do odpadu
Tento symbol na produkte alebo na jeho obale znamená, že nesmie by vyhodený s iným komunálnym odpadom. Namiesto toho máte povinnos odovzda toto zariadenie na zbernom mieste, kde sa zabezpečuje recyklácia elektrických a elektronických zariadení. Separovaný zber a recyklácia zariadenia určeného na odpad pomôže chráni prírodné zdroje a zabezpečí taký spôsob recyklácie, ktorý bude chráni ľudské zdravie a životné prostredie. Ďalšie informácie o separovanom zbere a recyklácii získate na miestnom obecnom úrade, vo firme zabezpečujúcej zber vášho komunálneho odpadu alebo v predajni, kde ste produkt kúpili.
Ravnanje z odpadno opremo v gospodinjstvih znotraj Evropske unije
Ta znak na izdelku ali embalaži izdelka pomeni, da izdelka ne smete odlagati skupaj z drugimi gospodinjskimi odpadki. Odpadno opremo ste dolžni oddati na določenem zbirnem mestu za recikliranje odpadne električne in elektronske opreme. Z ločenim zbiranjem in recikliranjem odpadne opreme ob odlaganju boste pomagali ohraniti naravne vire in zagotovili, da bo odpadna oprema reciklirana tako, da se varuje zdravje ljudi in okolje. Več informacij o mestih, kjer lahko oddate odpadno opremo za recikliranje, lahko dobite na občini, v komunalnem podjetju ali trgovini, kjer ste izdelek kupili.
Kassering av förbrukningsmaterial, för hem- och privatanvändare i EU
Produkter eller produktförpackningar med den här symbolen får inte kasseras med vanligt hushållsavfall. I stället har du ansvar för att produkten lämnas till en behörig återvinningsstation för hantering av el- och elektronikprodukter. Genom att lämna kasserade produkter till återvinning hjälper du till att bevara våra gemensamma naturresurser. Dessutom skyddas både människor och miljön när produkter återvinns på rätt sätt. Kommunala myndigheter, sophanteringsföretag eller butiken där varan köptes kan ge mer information om var du lämnar kasserade produkter för återvinning.
Chemical Substances
HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH (Regulation EC No
1907/2006 of the European Parliament and the Council). A chemical information report for this product can be found at: www.hp.com/go/reach .
58 Technical information
Toxic and hazardous substance table
Regulatory notices
The HP Printer meets product requirements from regulatory agencies in your country/region.
This section contains the following topics:
•
Regulatory model identification number
•
•
•
VCCI (Class B) compliance statement for users in Japan
•
Notice to users in Japan about the power cord
•
HP Deskjet D5500 Printer series declaration of conformity
Regulatory model identification number
For regulatory identification purposes, your product is assigned a Regulatory Model Number. The
Regulatory Model Number for your product is SNPRB-0921-04. This regulatory number should not be confused with the marketing name (HP Deskjet D5500 Printer series, etc.) or product numbers
(CH358, etc.).
Regulatory notices 59
Chapter 9
FCC statement
FCC statement
The United States Federal Communications Commission (in 47 CFR 15.105) has specified that the following notice be brought to the attention of users of this product.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For further information, contact:
Manager of Corporate Product Regulations
Hewlett-Packard Company
3000 Hanover Street
Palo Alto, Ca 94304
(650) 857-1501
Modifications (part 15.21)
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Notice to users in Korea
VCCI (Class B) compliance statement for users in Japan
60 Technical information
Notice to users in Japan about the power cord
HP Deskjet D5500 Printer series declaration of conformity
CLARATI ON OF C MITY
a ccording to ISO 0-1
mpany product
Product
Product
Name and Model:
Number: 1)
Options: el:
HP Deskjet
All
RSVLD-070 7
ns:
Safety:
EMC:
:2001 ass B
Radio:
005 / EN 301 489-17 V1.2.
1:2002
006 bject to the foll owing two con is device ence that may cause
carries the
02/95/EC.
Directive
mark accord ingly. In additi on, it complies with the
ion:
1) This pr ned a Regulator ry Model Numb ain product ide ntifier in the reg numbers.
The
U.S.:
only:
3000 Hanover St 04, U.S.A. 650 www .hp.com/go/cert tificates
Regulatory notices 61
Chapter 9
Regulatory wireless statements
This section contains the following regulatory information pertaining to wireless products:
•
Exposure to radio frequency radiation
•
•
•
European Union regulatory notice
•
Exposure to radio frequency radiation
Exposure to radio frequency radiation
Caution The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. This product and any attached external antenna, if supported, shall be placed in such a manner to minimize the potential for human contact during normal operation. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
Notice to users in Brazil
Aviso aos usuários no Brasil
Este equipamento opera em caráter secundário, isto é, não tem direito à proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. (Res.ANATEL 282/2001).
Notice to users in Canada
Notice to users in Canada/Note à l'attention des utilisateurs canadiens
For Indoor Use. This digital apparatus does not exceed the Class B limits for radio noise emissions from the digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications. The internal wireless radio complies with RSS
210 and RSS GEN of Industry Canada.
Utiliser à l'intérieur. Le présent appareil numérique n'émet pas de bruit radioélectrique dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. Le composant RF interne est conforme a la norme RSS-210 and RSS GEN d'Industrie Canada.
62 Technical information
European Union regulatory notice
European Union Regulatory Notice
Products bearing the CE marking comply with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
CE compliance of this product is valid only if powered with the correct CE-marked AC adapter provided by HP.
If this product has telecommunications functionality, it also complies with the essential requirements of the following EU Directive:
• R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to harmonized European standards
(European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or product family. This compliance is indicated by the following conformity marking placed on the product.
The wireless telecommunications functionality of this product may be used in the following
EU and EFTA countries:
Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Products with 2.4-GHz wireless LAN devices
France
For 2.4 GHz Wireless LAN operation of this product certain restrictions apply: This product may be used indoor for the entire 2400-2483.5 MHz frequency band (channels
1-13). For outdoor use, only 2400-2454 MHz frequency band (channels 1-9) may be used.
For the latest requirements, see http://www.art-telecom.fr.
Italy
License required for use. Verify with your dealer or directly with the General Direction for
Frequency Planning and Management (Direzione Generale Pianificazione e Gestione
Frequenze).
Regulatory wireless statements 63
Chapter 9
Notice to users in Taiwan
64 Technical information
Index
A
C
connection problems
HP All-in-One will not turn
customer support
E
environment
Environmental product
environmental
I
N
network
P
paper
phone support period print
printer found screen,
printing
problems
R
recycle
regulatory notices regulatory model
S
security
software installation
T
technical information environmental
specifications 55 system requirements 55
troubleshoot
troubleshooting
U
W
65
66
advertisement
Related manuals
advertisement