advertisement
PDP-TELEVISION
(P
LASMA
D
ISPLAY
P
ANEL
)
Owner’s Instructions
Before operating the unit, please read this manual thoroughly, and retain it for future reference.
ON-SCREEN MENUS
Picture In Picture (PIP)
Energy Saving
TELETEXT
(Option)
SRS TruSurroundXT
Digital Natural Image engine
This device is a Class B digital apparatus.
Register your product at www.samsung.com/global/register
User Instructions
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
◆ Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.
◆ Heat on the top of the PDP TV
The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.
◆ The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.
◆ Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
◆ Avoid operating the TV at temperatures below 5°C(41°F)
◆ A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen.
Playing a DVD or a game console may cause similar effect to the screen.
Damages caused by the above effect are not covered by the Warranty.
◆ Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial after images. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
◆ Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
Checking Parts
Sold Separately
Owner’s
Instructions
Remote Control/
AAA Batteries S-VIDEO Cable HDMI Cable Antenna Cable Component Cables
(RCA)
Power Cord
Ferrite Core for Antenna
Cable and Power Cord
➢
Ferrite Core (Power Cord, Antenna Cable)
The ferrite core is used to shield the cable from interference. When connecting a cable,open the ferrite core and clip it around the cable.
PC Cable PC Audio Cable HDMI/DVI Cable
English - 2
Contents
◆ G
ENERAL
I
NFORMATION
■
■
■
■
■
■
User Instructions ...................................................................................................
Checking Parts......................................................................................................
Control Panel ........................................................................................................
Connection Panel..................................................................................................
Viewing the Remote Control (depending on the model) .......................................
Installing Batteries in the Remote Control ............................................................
◆ O
PERATION
■
■
■
■
■
■
Switching Your Television On and Off ...................................................................
Viewing the Menus................................................................................................
Freezing the Current Picture.................................................................................
Plug & Play Feature ..............................................................................................
Viewing an External Signal Source.......................................................................
Editing Device Names...........................................................................................
◆ C
HANNEL
C
ONTROL
■
■
■
■
■
■
Storing Channels Automatically ............................................................................
Storing Channels Manually ...................................................................................
Adding / Locking Channels ...................................................................................
Sorting the Stored Channels.................................................................................
Assigning Names to Channels..............................................................................
Fine Tuning Channel Reception............................................................................
◆ P
ICTURE
C
ONTROL
■
■
■
■
■
■
■
Changing the Picture Standard.............................................................................
Customizing the Picture Settings ..........................................................................
Selecting the Picture Size .....................................................................................
Digital NR ..............................................................................................................
SMD ......................................................................................................................
DNIe Demo ...........................................................................................................
Viewing the Picture in Picture (PIP) ......................................................................
◆ S
OUND
C
ONTROL
■
Sound Features.....................................................................................................
◆ F
UNCTION
D
ESCRIPTION
■
■
■
■
■
■
■
■
Time Features .......................................................................................................
Language ..............................................................................................................
Blue Screen...........................................................................................................
Melody...................................................................................................................
Energy Saving.......................................................................................................
Using Game Mode ................................................................................................
Screen Burn Protection .........................................................................................
Setting the Blue Eye .............................................................................................
◆ PC D
ISPLAY
■
■
■
Setting up Your PC Software (Based on Windows XP) ........................................
Input Mode (PC)....................................................................................................
Setting the PC .......................................................................................................
13
14
15
16
16
17
9
10
8
9
12
12
18
18
19
20
20
20
21
22
24
24
25
26
23
24
24
24
26
27
28
5
7
8
2
2
5
English - 3
Contents
◆ U
SING
T
HE
DTV F
EATURE
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Previewing the DTV Menu System .......................................................................
Updating the Channel Manager Automatically......................................................
Updating the Channel Manager Manually.............................................................
Editing Your Favourite Channels...........................................................................
Select Channel Manager.......................................................................................
Viewing Channel Lists...........................................................................................
Displaying Programme Information.......................................................................
Viewing the EPG (Electronic Programme Guide) Information ..............................
Using the Scheduled List ......................................................................................
Setting the Default Guide......................................................................................
Viewing All Channels and Favourite Channels .....................................................
Adjusting the Translucency Level .........................................................................
Setting up the Parental Lock.................................................................................
Setting the Subtitle ................................................................................................
Selecting the Preferred Language (Subtitle or Audio) ..........................................
Selecting the Audio Format...................................................................................
Selecting the Time Zone .......................................................................................
Viewing Product Information .................................................................................
Checking the Signal Information ...........................................................................
Upgrading the Software (Option) ..........................................................................
Resetting ...............................................................................................................
◆ U
SING THE
T
ELETEXT
F
EATURE
■
Teletext Feature (depending on the model) ..........................................................
◆ A
PPENDIX
■
■
How to Install the Wall Mount Bracket ..................................................................
Troubleshooting.....................................................................................................
42
43
44
45
37
39
40
41
29
30
31
32
35
35
36
46
47
48
48
49
50
51
53
55
Symbols
Press
☛
Important
➢
Note
English - 4
Control Panel
➢
The product colour and shape may vary depending on the model.
Front (or Side) Panel
Speaker
Œ SOURCE
Displays a menu of all of the available input sources
(TV, AV1, AV2, S-Video, Component1, Component2,
PC, HDMI, DTV).
´ MENU
Press to see the on-screen menu of your TV’s features.
ˇ VOL +, -
Press to increase or decrease the volume.
In the on-screen menu, use the VOL +, - buttons as you use the œ and √ buttons on the remote control.
¨ CH ,
Press to change channels. In the on-screen menu, use the CH , buttons as you use the … and † buttons on the remote control.
ˆ (ENTER)
Press to confirm a selection.
Ø (Power) button
Press to turn the TV on and off.
Power Indicator
- Power Off: Blue
- Power On: Off
Remote Control Sensor
Aim the remote control towards this spot on the TV.
Connection Panel
➢
The product colour and shape may vary depending on the model.
Side Panel
Œ
or
´
Œ S-Video or Video / Audio L/R
- Video (S-Video or Video) and audio inputs for external devices, such as a camcorder or VCR.
´ headphones jack
- You can connect a set of headphones to your television if you wish to watch a television programme without disturbing the other people in the room.
➢
Prolonged use of headphones at a high volume may damage your hearing.
continued...
English - 5
Connection Panel
➢
The product colour and shape may vary depending on the model.
Rear Panel
TruSurround XT, SRS and symbolare trademarks of SRS Labs, Inc.
or
Cable Television
Network or
☛ Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
☛ When connecting an external device, match the colour of the connection terminal to the cable.
ANT IN VHF/UHF (75Ω)
- 75Ω Coaxial connector for Aerial/Cable Network.
Connecting external Audio Devices
- Connect RCA audio signals from the TV to an external source, such as Audio equipment.
PC IN / AUDIO
- Connect to the video and audio output jack on your PC.
- When connecting this product via HDMI or DVI to a
Set Top Box, DVD Player or Games Console etc, make sure that it has been set to a compatible video output mode as shown in the table below. Failure to observe this may result in picture distortion, image breakup or no picture.
- Do not attempt to connect the HDMI/DVI connector to a
PC or Laptop Graphics Card.
(This will result in a blank screen being displayed)
DVI AUDIO IN L/R
- DVI audio outputs for external devices.
Connecting External A/V Devices
- Connect RCA cable to an appropriate external A/V device such as VCR, DVD or Camcorder.
- Connect RCA audio cables to “R - AUDIO - L” on the rear of your set and the other ends to corresponding audio out connectors on the A/V device.
COMPONENT IN 1, COMPONENT IN 2
- Video (Y/PB/PR) and audio (AUDIO L/R) inputs for
Component.
HDMI/DVI IN
- Connect to the HDMI jack of a device with HDMI output.
These inputs can also be used as a DVI connection with separate analog audio inputs. An optional
HDMI/DVI cable will be necessary to make this connection. When using the optional HDMI/DVI adapter, the DVI analog audio inputs on your TV allow you to receive left and right audio from your DVI device.
(Not compatible with PC)
POWER IN
- Connect the supplied power cord.
SERVICE
- Connector for service only.
DIGTAL AUDIO OUT (OPTICAL)
Connect optical digital audio cable to "DIGITAL AUDIO OUT" on the rear of your set and the other end to "DIGITAL IN" of the equipment with a digital input to enjoy digital sound.
➢ Supported modes for HDMI/DVI and Component
HDMI/DVI 50Hz
HDMI/DVI 60Hz
Component
480i
X
X
O
480p
X
O
X
576i
X
X
O
576p
O
X
O
720p
O
O
O
1080i
O
O
O
English - 6
Viewing the Remote Control
(depending on the model)
Select the TV mode directly
POWER button
(turns the TV on and off)
Number buttons for direct channel access
One/Two-digit channel selection
Channel control button
(Refer to page 15)
Interchange the TV and DTV mode
VCR/DVD functions
- REWIND (REW)
- STOP
- PLAY/PAUSE
- FAST FORWARD (FF)
Volume increase
Volume decrease
Temporary sound switch-off
Displays the main on-screen menu
Control the cursor in the menu
Use to see information on the current broadcast
Electronic program guide (EPG) display
Picture effect selection
(Refer to page 18)
Picture-In-Picture On/Off
Picture freeze
Sound mode selection
Make the remote control work for STB, VCR, CABLE or DVD
Available source selection
Previous channel
DTV menu display
Automatic Power-off
Next channel
Previous channel
Exit the on-screen menu
Sound effect selection
(Refer to page 21)
Picture size selection
Digital subtitle display
TruSurround XT mode button
Remote control setup
If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds.
Re-insert the batteries and try using the remote control again.
Teletext Functions (Refer to page 51)
Exit from the teletext display
(depending on the model)
Teletext index
Teletext reveal
Teletext size selection
Teletext hold
Teletext mode selection
(LIST/FLOF)
Teletext sub page
P : Teletext next page
P : Teletext previous page
Teletext cancel
Teletext display/mix both teletext information and the normal broadcast
Teletext store
Fastext topic selection
➢
The performance of the remote control may be affected by bright light.
➢
This is a special remote control for the visually impaired, and has Braille points on the Power, Channel and
Volume buttons.
English - 7
Installing Batteries in the Remote Control
1 Lift the cover at the back of the remote control upward as shown in the figure.
2 Install two AAA size batteries.
➢
Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.
3 Close the cover as shown in the figure.
➢
Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.
➢
If the remote control doesn’t work! Check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Switching Your Television On and Off
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
2 Press the (Power) button (On/Off) on the front of the television or press the POWER ( ) button on the remote control to switch the television on. The programme that you were watching last is re-selected automatically.
If you have not yet stored any channels, no clear picture appears. Refer to “Storing Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.
➢
If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 10.
3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press the
POWER ( ) button on the remote control.
4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER ( ) button or number buttons on the remote control.
English - 8
Viewing the Menus
1 Press the MENU ( ) button.
The main menu is displayed on the screen.
Its left side has five icons: Input, Picture, Sound, Channel, and Setup.
2 Press the … or † button to select one of the icons.
Press the ENTER ( ) button to access the icon’s sub-menu.
3 Press the … or † button to move to items in the menu.
Press the ENTER ( ) button to enter items in the menu.
4 Press the …/†/œ/√ button to change the selected items.
Press the MENU ( ) button to return to the previous menu.
5 Press the EXIT button to exit from the menu.
TV
Source List
Edit Name
Input
: TV
Move Enter Exit
Freezing the Current Picture
You can freeze the picture when watching a television programme simply by pressing the “STILL” button. To return to normal viewing, press it again.
➢
This function will automatically cancel five minutes later.
English - 9
Plug & Play Feature
When the television is initially powered on, several basic customer settings proceed automatically and subsequently.
The following settings are available.
Plug & Play
Start Plug & Play.
OK
Enter Exit
Plug & Play
Check antenna input.
OK
Enter Skip
Plug & Play
Auto Store
P 1 C -40 MHz
0 %
Start
Enter Skip
1 If the television is in standby mode, press the POWER ( ) button on the remote control. The message to start Plug & Play is displayed.
2 Make sure that the antenna is connected to the TV.
Press the ENTER ( ) button. The menu to select channels is displayed
3 To start channel store, press the ENTER ( ) button.
The search will end automatically. The TV will begin memorizing all of the available channels.
Press the ENTER ( ) button to set the clock.
4 Press the œ or √ button to select the hour or minute.
Set these by pressing the … or † button.
➢
You can enter the hours or minutes by using the numeric buttons on the remote control.
Plug & Play
Auto Store
P 1 C -40 MHz
0 %
Stop
Enter Skip
Plug & Play
Clock Set -- : --
Enter Skip
Plug & Play
Clock Set 12 : 00
Move Adjust Enter Skip
English - 10
5 Plug and Play for TV complete, and Plug and Play for DTV will start automatically.
The search will end automatically. Channels are sorted and stored in the order which reflects their position in the frequency range (with lowest first and highest last). When this has finished, the menu to set the Time Zone will be displayed.
➢
To stop DTV channel the search before it has finished or return to normal viewing, press the D.MENU or the ENTER ( ) button.
6 Select the time zone where you locate by pressing the … or † button.
Press the ENTER ( ) button.
The following options are available.
New South Wales/ACT - Victoria - Queensland - South
Australia - Western Australia - Tasmania - Northern
Territory
7 Press the ENTER ( ) button to confirm your setting.
The message “Enjoy your watching” is displayed.
Plug & Play
Scanning for digital services...
7
Services found:0 Channel:9A
39%
Stop
Skip
The channel list is being updated.
To abort the scan press D.MENU.
Plug & Play
New South Wales/ACT
Victoria
Queensland
South Australia
Western Australia
Tasmania
Northern Territory
Move Select Skip
Selects the time zone where you locate
Plug & Play
New South Wales/ACT
Victoria
Queensland
South Australia
Western Australia
Tasmania
Northern Territory
Move Select Skip
Selects the time zone where you locate
Plug & Play
Enjoy your watching
OK
Exit
If you want to reset this feature …
1 Press the MENU ( ) button to display the menu. (On TV mode)
2 Press the … or † button to select Setup, then press the ENTER ( button.
3 Press the ENTER ( ) button again to select Plug & Play.
The message to start Plug & Play is displayed.
)
TV
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
Move
Setup
: English
: Off
: Off
: Off
Enter Return
English - 11
Viewing an External Signal Source
You can switch between viewing signal from connected equipment, such as a VCR, DVD, Set-Top Box, and the TV source (broadcast or cable).
TV
Source List
Edit Name
Input
: TV
TV
Move Enter Return
TV
AV1
AV2
S-Video
Component1
Component2
PC
HDMI
DTV
Move
Source List
:
:
:
:
:
:
: ----
----
----
----
----
----
----
Enter Return
1 Press the MENU (
2 Press the ENTER (
) button to display the menu.
) button to select Source List.
3 Press the ENTER ( ) button again.
4 Press the … or † button to select the signal source, then press the
ENTER ( ) button.
Available signal source: TV, AV1, AV2, S-Video, Component1,
Component2, PC, HDMI, DTV
➢
You can select these options simply by pressing the SOURCE button on the remote control. (Only for External Signal Source)
Editing Device Names
You can give a name to the external source.
TV
Source List
Edit Name
Input
: TV
TV
Move Enter Return
AV1
AV2
S-Video
Component1
Component2
PC
HDMI
Edit Name
:
:
:
:
:
:
: ----
----
----
----
VCR
----
----
DVD
----
Move Enter Return
1 Press the MENU (
2 Press the ENTER (
) button to display the menu.
) button.
3 Press the … or † button to select Edit Name, then press theENTER ( button.
4 Press the … or † button to select the external source to be edited, then press the ENTER ( ) button.
5 Select the required device by pressing … or †, then press the ENTER ( button.
Available device names: VCR, DVD, D-VHS, Cable STB, HD STB,
Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder,
DVD Combo, DHR (DVD HDD Recorder), or PC.
6 Press the EXIT button to exit.
)
)
English - 12
Storing Channels Automatically
You can scan for the frequency ranges available to you (availability depends on your Country).
Automatically allocated programme numbers may not correspond to actual or desired programme numbers.
However you can sort numbers manually and clear any channels you do not wish to watch.
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Channel, then press the ENTER ( button.
3 Press the … or † button to select Auto Store, then press the ENTER ( button.
)
)
4 Press the ENTER ( ) button again to start the search.
The search will end automatically.
➢
To stop the search before it has finished, press the MENU ( ) or the
ENTER ( ) button.
➢
The Australia is the default in the Country cases depending on the model.
TV
Country
Auto Store
Sort
Name
Fine Tune
Channel
: Australia
Manual Store
Channel Manager
Move Enter Return
Auto Store
P 1 C -40 MHz
0 %
Start
Enter Return
English - 13
Storing Channels Manually
You can store television channels, including those received via cable networks.
When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found.
◆ The programme number of each stored channel which you wish to identify.
TV
Country
Auto Store
Sort
Name
Fine Tune
Channel
: Australia
Manual Store
Channel Manager
Move Enter Return
TV Manual Store
Programme
Colour System
Sound System
Channel
Search
Store
: P
: AUTO
: BG
1
: C 2
: 48 MHz
: ?
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Channel, then press the ENTER ( button.
)
3 Press the … or † button to select Manual Store, then press the ENTER ( button.
4 Select the required option by pressing the … or † button, then press the
ENTER ( ) button.
5 When you are satisfied with your setting, press the ENTER (
6 Press the EXIT button to exit.
) button.
)
Move Enter Return
◆ Programme (Programme number to be assigned to a channel)
- Press the … or † button until you find the correct number.
◆ Colour System: AUTO/PAL/SECAM/NTSC4.43
- Press the … or † button to select the required colour standard.
◆ Sound System: BG/DK/I
- Press the … or † button to select the required sound standard.
◆ Channel (When you know the number of the channel to be stored)
- Press the … or † button to select C (Air channel) or S (Cable channel).
- Press the √ button, then press the … or † button to select the required number.
➢
You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, re-select the sound standard required.
◆ Search (When you do not know the channel numbers)
- Press the … or † button to start the search.
- The tuner scans the frequency range until the first channel or the channel that you selected is received on the screen.
◆ Store (When you store the channel and associated programme number)
- Set to OK by pressing the ENTER ( ) button.
☛
Channel mode
◆ P (Programme mode): When completing tuning, the broadcasting stations in your area have been assigned to position numbers from P00 to P99. You can select a channel by entering the position number in this mode.
◆ C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in this mode.
◆ S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.
English - 14
Adding / Locking Channels
Using the Channel Manager, you can conveniently lock or add channels.
1 Press the MENU (
2
) button to display the menu.
Press the … or † button to select Channel, then press the ENTER (
3 Press the … or † button to select Channel Manager, then press the
ENTER ( ) button.
) button.
◆ Adding channels
Using the Channel Manager, you can add channels.
4 Select the Channel Manager by pressing the ENTER ( ) button.
5 Move to the ( ) field by pressing the …/†/œ/√ buttons, select a channel to be added, and press the ENTER ( ) button to add the channel.
➢
If you press the ENTER ( ) button again, the ( ) symbol next to the channel disappears and the channel is not added.
◆ Locking channels
This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video and audio.
6 Press the … or † button to select Child Lock, then press the ENTER ( button.
7 Select On by pressing the … or † buttons, then press the ENTER ( button.
)
8 Press the … or † buttons to select the Channel Manager, then press the
ENTER ( ) button.
)
9 Move to the ( ) field by pressing the …/†/œ/√ buttons, select a channel to be locked, and press the ENTER ( ) button.
➢
If you press the ENTER ( ) button again, the ( ) symbol next to the channel disappears and the channel lock is canceled.
➢
A blue screen is displayed when Child Lock is activated.
10 Press the EXIT button to exit.
TV Channel
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
TV
Move Enter
Channel Manager
Channel Manager
Child Lock : Off
Return
Move Enter
TV Channel Manager
Channel Manager
Child Lock : On
Return
Move Enter
Channel Manager
P 1 C 16 BBC 1
1 / 10
Prog.
0 C --
1 BBC 1
2 C 3
3 S 1
4 S 3
5 S 6
6 S 7
7 S 9
8 S 11
9 S 12
Add Lock
Move
Page
Enter
Return
Return
➢
You can select these options simply by pressing the CH MGR button on the remote control.
English - 15
Sorting the Stored Channels
This operation allows you to change the programme numbers of stored channels.
This operation may be necessary after using auto store.
TV
Country
Auto Store
Sort
Name
Fine Tune
Channel
: Australia
Manual Store
Channel Manager
TV
Move Enter
Prog. Ch.
0
3
4
1
2
C --
C 2
C 83
C 80
C 7
Sort
Name
Return
Move Enter Return
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Channel, then press the ENTER (
3 Press the … or † button to select Sort, then press the ENTER (
) button.
) button.
4 Select the channel that you wish to move by pressing the … or † button, then press the ENTER ( ) button.
5 Select the number of the programme to which the channel is to be moved by pressing the … or † button.
Press the ENTER ( ) button. The channel is moved to its new position and all other channels are shifted accordingly.
6 Repeat steps 4 to 5 until you have moved all the channels to the required programme numbers.
7 Press the EXIT button to exit.
Assigning Names to Channels
Channel names will be assigned automatically when channel information is broadcast.
These names can be changed, allowing you to assign new names.
TV
Country
Channel
: Australia
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
TV
Move Enter Return
Prog. Ch.
0
3
4
1
2
C --
C 2
C 83
C 80
C 7
Name
Name
-----
-----
-----
-----
Move Adjust Return
Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names.
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Channel, then press the ENTER ( ) button.
3 Press the … or † button to select Name, then press the ENTER ( button.
)
4 Press the … or † button to select the channel to be assigned to a new name, then press the ENTER ( ) button.
5 Press the … or † button to select a letter (A~Z), a number (0~9), or a symbol.
Move on to the previous or next letter by pressing the œ or √ button, then press the ENTER ( ) button.
6 Repeat steps 4 to 5 for each channel to be assigned to a new name.
7 Press the EXIT button to exit.
English - 16
Fine Tuning Channel Reception
If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Channel, then press the ENTER ( button.
3 Press the … or † button to select Fine Tune, then press the ENTER ( button.
)
)
4 To obtain a sharp and clear picture and good sound quality, press the œ or √ button until you reach the optimal setting. Press the ENTER ( ) button.
➢
To reset the fine tuning to 0, select Reset by pressing the … or † button. Press the ENTER ( ) button.
5 Press the EXIT button to exit.
➢
Fine Tune Store will change the colour of the Channel OSD (On Screen
Display) from White to Red and add the “*” mark.
TV
Country
Auto Store
Sort
Name
Fine Tune
Channel
: Australia
Manual Store
Channel Manager
Move Enter Return
Fine Tune
P 1 *
+3
Adjust
Reset
Save Return
P 1 *
Mono
English - 17
Changing the Picture Standard
You can select the type of picture which best corresponds to your viewing requirements.
TV 1 Press the MENU ( ) button to display the menu.
Mode
Size
Digital NR
SMD
DNIe Demo
PIP
Picture
: Dynamic
: 16:9
: On
: On
: Off
2
3
Press the … or † button to select Picture, then press the ENTER ( button.
Press the ENTER ( ) button twice.
Move Enter Return
)
4 Select the required mode by pressing the … or † button, then press the
ENTER ( ) button.
TV
Mode
Contrast
Brightness
Sharpness
Colour
Tint G 50
Colour Tone
Reset
Mode
: Dynamic
Standard
Movie
Custom
100
50
75
55
R 50
: Cool 1
Move Enter Return
Available modes: Dynamic, Standard, Movie, Custom
➢
The settings values may vary depending on the input source.
(ex. RF, Video, Component, PC, or HDMI)
5 Press the EXIT button to exit.
➢
You can select these options simply by pressing the P.MODE button on the remote control.
➢ ◆ Choose Dynamic for viewing the TV during the day or when there is bright light in the room.
◆ Choose Standard for the standard factory settings.
◆ Choose Movie when viewing the movie.
◆ Choose Custom if you want to adjust the settings according to personal preference.
Customizing the Picture Settings
Your television has several setting options that allow you to control the picture quality.
TV
TV
Mode
Size
Digital NR
SMD
DNIe Demo
PIP
Picture
: Dynamic
: 16:9
: On
: On
: Off
Move Enter Return
Mode
Contrast
Brightness
Sharpness
Colour
Tint G 50
Colour Tone
Reset
Mode
: Dynamic
Cool 2
Cool 1
Normal
100
50
75
55
R 50
Warm 2
Move Enter Return
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Picture, then press the ENTER ( button.
3 Press the ENTER ( ) button twice.
)
4 Select the required mode by pressing the … or † button, then press the
ENTER ( ) button.
Available modes: Dynamic, Standard, Movie, Custom
5 Select the required option by pressing the … or † button, then press the
ENTER ( ) button.
6 When you are satisfied with your setting, press the ENTER ( ) button.
7 Press the EXIT button to exit.
◆ Contrast – Brightness – Sharpness – Colour – Tint (NTSC only)
◆ Contrast – Brightness – Colour : PC Mode
Press the œ or √ button until you reach the optimal setting.
◆ Colour Tone: Cool 2/Cool 1/Normal/Warm 1/Warm 2
◆ Reset: You can return to the factory defaults picture settings.
➢
The reset function is set for each picture mode and colour tone.
English - 18
Selecting the Picture Size
You can select the picture size which best corresponds to your viewing requirements.
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Picture, then press the ENTER ( button.
3 Press the … or † button to select Size, then press the ENTER (
)
) button.
4 Select the required option by pressing the … or † button, then press the
ENTER ( ) button.
Available options: 16:9, Wide 4:3, Zoom, 4:3
◆ 16:9: Sets the picture to 16:9 wide mode.
◆ Wide 4:3: Magnify the size of the picture more than 4:3.
Move the screen up/down using the … or † button after selecting the by pressing the √ or ENTER (
◆ Zoom: Magnify the size of the picture vertically on screen.
◆ 4:3: Sets the picture to 4:3 normal mode.
) button.
5 Press the EXIT button to exit.
➢
You can change the picture size simply by pressing the P.SIZE button on the remote control.
➢
If you change the picture size when PIP is On, PIP will automatically be turned Off.
➢
Depending on the input source, the picture size options may vary.
The items available may differ depending on the selected mode.
TV
Mode
Size
Digital NR
SMD
DNIe Demo
PIP
Picture
: Dynamic
: 16:9
: On
: On
: Off
TV
16:9
Wide 4:3
Zoom
4:3
Move Enter
Size
Move Enter
Return
Return
Positioning and Sizing the screen using Zoom
◆ Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down direction using the … or † button as well as the screen size.
◆ Move the screen up/down using the … or † button after selecting the
◆ Resize the screen vertically using the … or † button after selecting the by pressing the œ or √ button.
by pressing the œ or √ button.
English - 19
Digital NR / SMD / DNIe Demo
TV
Mode
Size
Digital NR
SMD
DNIe Demo
PIP
Picture
: Dynamic
: 16:9
: On
: On
: Off
Move Enter Return
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Picture, then press the ENTER ( button.
)
3 Select the required option by pressing the… or † button, then press the
ENTER ( ) button.
Available options: Digital NR, SMD, DNIe Demo
4 When you are satisfied with your setting, press the ENTER ( ) button.
5 Press the EXIT button to exit.
◆ Digital NR: On/Off
If the signal received by the television is weak, you can activate this feature to reduce any static and ghosting that may appear on the screen.
◆ SMD(Smooth Motion Driver): On/Off
If you set SMD to On, you can view more natural skin and clear text even in fast moving scenes.
(SMD is applicable only to PAL and SECAM system.)
➢
SMD is not available in PC mode.
◆ DNIe Demo: On/Off
This TV includes the DNIe function so as to provide a high visual quality.
If you set DNIe Demo to On, you can view an applied DNIe and a normal picture on the screen, for demonstration purposes. Using this function, you can view the difference in the visual quality.
➢
DNIe TM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement, contrast enhancement and white enhancement.
New image compensation Algorithm gives brighter, clearer, more detailed image to you. DNIe TM eyes.
technology will fit every signal into your
➢
DNIe Demo is not available in PC mode.
English - 20
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture. In this way you can watch TV program or monitor the video input from any connected devices.
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Picture, then press the ENTER ( button.
3 Press the … or † button to select PIP, then press the ENTER (
)
) button.
4 Select the required option by pressing the … or † button, then press the
ENTER ( ) button.
Available options: PIP(On/Off), Source, Position, Programme
5 When you are satisfied with your setting, press the ENTER ( ) button.
6 Press the EXIT button to exit.
TV
TV
Mode
Size
Digital NR
SMD
DNIe Demo
PIP
Picture
: Dynamic
: 16:9
: On
: On
: Off
Move
PIP
Source
Position
Programme
Enter
PIP
: On
: AV1
:
: P 1
Return
◆ PIP: On/Off
You can activate or deactivate the PIP function.
➢
You can select these options simply by pressing the PIP button on the remote control.
◆ Source: TV/AV1/AV2/S-Video
You can select a source of the sub-picture.
◆ Position: / / /
You can select a position of the sub-picture.
◆ Programme
You can select a channel of the sub-picture only when the Source is set to TV.
Move Enter Return
Easy functions of the remote control.
Buttons
PIP
Feature
Used to activate or deactivate the PIP function directly.
Table of PIP Settings
Main
TV
AV1
AV2
S-Video
Component1
Sub
Component2
HDMI
PC
DTV
TV
X
X
X
X
X
X
O
O
X
AV1
X
X
X
X
X
X
O
O
X
X - This PIP combination is not available.
O - This PIP combination is available.
AV2
X
X
X
X
X
X
O
O
X
S-Video
X
X
X
X
X
X
O
X
X
PC
X
X
X
X
X
X
X
X
X
DTV
X
X
X
X
X
X
X
X
X
English - 21
Sound Features
TV
Mode
Equalizer
SRS TSXT
Auto Volume
Internal Mute
Reset
Sound
: Custom
: Off
: Off
: Off
Move Enter
< If Game Mode is On >
TV Sound
Mode
Equalizer
SRS TSXT
Auto Volume
Internal Mute
Reset
: Custom
: Off
: Off
: Off
Return
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Sound, then press the ENTER ( button.
)
3 Select the required option by pressing the … or † button, then press the
ENTER ( ) button.
Available options: Mode, Equalizer, SRS TSXT, Auto Volume,
Internal Mute, Reset (If Game Mode is On)
4 When you are satisfied with your setting, press the ENTER ( ) button.
5 Press the EXIT button to exit.
Move Enter Return
◆ Mode: Standard/Music/Movie/Speech/Custom
You can select the type of special sound effect to be used when watching a given broadcast.
➢
You can select these options simply by pressing the S.MODE button on the remote control.
TV Equalizer
◆ Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
The television has several settings which allow you to control the sound quality.
➢
If you make any changes to these settings, the sound mode is automatically switched to Custom.
R
+
0
L
Balance
-
100 Hz 300 Hz 1k Hz 3k Hz
-
10k Hz
+
0
Move Adjust Return
◆ SRS TSXT: On/Off
TruSurround XT is a patented SRS technology that solves the of playing 5.1
multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.
➢
You can select these options simply by pressing the SRS( ) button on the remote control.
➢
TruSurround XT, SRS and Symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS
Labs, Inc.
◆ Auto Volume: On/Off
Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.
◆ Internal Mute: On/Off
If you want to hear the sound through separate speakers, cancel the internal amplifier.
➢
The VOL +, VOL - and Mute buttons do not operate when the Internal
Mute is set to On.
◆ Reset
If Game Mode is On, the Reset Sound function is activated. Selecting the Reset function after setting the equalizer resets the equalizer setting to the factory defaults.
English - 22
Time Features
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Setup, then press the ENTER ( ) button.
3 Press the … or † button to select Time, then press the ENTER ( ) button.
4 Select the required option by pressing the … or † button, then press the
ENTER ( ) button.
Available options: Clock Set, Sleep Timer, On Timer, Off Timer
5 When you are satisfied with your setting, press the ENTER ( ) button.
6 Press the EXIT button to exit.
◆ Clock Set
You can set the television clock so that the current time is displayed when pressing the INFO button on the remote control. You must also set the time if you wish to use the automatic on or off timers.
- Press the œ or √ button to select Hour or Minute.
Set these by pressing the … or † button.
➢
You can set the hour and minute directly by pressing the numeric buttons on the remote control.
➢
In the event of a power interruption or the set being turned off at the supply, the settings for the Clock will be lost.
TV
TV
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
Move
Setup
: English
: Off
: Off
: Off
Enter Return
Time
Clock Set 12 : 00
Sleep Timer
On Timer
Off Timer
: Off
12 : 00
12 : 00
Off
Off
Move Enter Return
◆ Sleep Timer
You can select a time period of between 30 and 180 minutes after which the television automatically switches to standby mode.
- Select the preset time interval (Off, 30, 60, 90, 120, 150, or 180) for staying on by pressing the … or † button.
➢
You can select these options simply by pressing the SLEEP button on the remote control. If the sleep timer is not yet set, Off is displayed.
If it is already set, the remaining time before which the television switches to standby mode is displayed.
◆ On Timer / Off Timer
You can set the On/Off timers so that the television will switch on or off automatically at the time you select.
☛
You must set the clock first.
- On Timer: Select Hour, Minute, Programme, or Volume by pressing the œ or √ button.
Set these by pressing the … or † button.
To activate On Timer with the setting satisfied, set Activation to Yes by … or † button.
➢
You can set the hour and minute directly by pressing the numeric buttons on the remote control.
- Off Timer: Select Hour or Minute by pressing the œ or √ button.
To activate Off Timer with the setting satisfied, set Activation to Yes by … or † button.
➢
You can set the hour and minute directly by pressing the numeric buttons on the remote control.
☛
Auto Power Off
When you set the timer “On”, the television will eventually turn off, if no controls are operated for 3 hours after the TV was turned on by timer. This function is only available in timer “On” mode and prevents overheating or leakages, which may occur if a TV is on for too long (when you are on vacation, for example).
English - 23
Language / Blue Screen / Melody / Energy Saving
TV
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
Move
Setup
: English
: Off
: Off
: Off
1 Press the MENU (
2
3
) button to display the menu.
Press the … or † button to select Setup, then press the ENTER (
ENTER ( ) button.
Enter Return
Available options: Blue Screen, Melody, Energy Saving
4 When you are satisfied with your setting, press the ENTER (
5 Press the EXIT button to exit.
◆ Language
It is variable depending on the model, English is the default in cases depending on the model.
) button.
Select the required option by pressing the … or † button, then press the
) button.
◆ Blue Screen: On/Off
If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the Blue Screen to Off.
◆ Melody: On/Off
You can hear melody sound when the television is powered on or off.
◆ Energy Saving: Off/Low/Medium/High
This feature adjusts the screen brightness depending on the surrounding lighting conditions.
Off: Switches off the Energy Saving mode.
Low: Operates in standard mode regardless of the surrounding illumination.
Medium: Enters Medium power saving mode regardless of the surrounding illumination.
High: Enters maximum power saving mode regardless of the surrounding illumination.
Using Game Mode
When connecting to a game console such as PlayStation TM experience by selecting game menu.
or Xbox TM , you can enjoy a more realistic gaming
TV
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
Move
Setup
: English
: Off
: Off
: Off
Enter Return
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Setup, then press the ENTER ( button.
)
3 Press the … or † button to select Game Mode, then press the ENTER
( ) button.
4 Select Off or On by pressing the … or † button, then press the ENTER
( ) button.
5 Press the EXIT button to exit.
➢
To disconnect the game console and connect another external device, cancel game mode in the picture menu.
➢
If you display the TV menu in Game mode, the screen shakes slightly.
➢
Game Mode is not available in TV mode.
➢
If Game Mode is On :
◆ Picture Mode is automatically changed to Custom and users cannot change the mode.
◆ Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.
◆ The Reset Sound function is activated. Selecting the Reset function after setting the equalizer resets the equalizer setting to the factory defaults.
English - 24
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical Line) and side to side (Horizontal Dot). The Time setting allows you to program the time between movement of the picture in minutes.
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Setup, then press the ENTER ( ) button.
3 Press the … or † button to select Screen Burn Protection, then press the
ENTER ( ) button.
4 Select the required option by pressing the … or † button, then press the
ENTER ( ) button.
Available options: Pixel Shift, All White, Signal Pattern
5 When you are satisfied with your setting, press the ENTER ( ) button.
6 Press the EXIT button to exit.
TV Setup
More
Energy Saving : Off
Screen Burn Protection
Blue Eye : On
TV
Move Enter Return
Screen Burn Protection
Pixel Shift
All White
Signal Pattern
TV
Move Enter
Pixel Shift
Pixel Shift
Horizontal Dot
Vertical Line
Time
: On
: 4
: 4
: 4
Return
Move Enter
◆ Pixel Shift: Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after image on the screen.
- Set Pixel Shift to On by pressing the … or † button, then press the ENTER (
- Select the required option by pressing the … or † button, then press the ENTER (
) button.
) button.
Available options: Horizontal Dot, Vertical Line, Time
➢
Optimum condition for pixel shift;
Horizontal Dot
Vertical Line
4
4
Time (minute) 4
Return
◆ All White: This function helps remove after images on the screen by changing the colour of pixels to white.
Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time.
◆ Signal Pattern: This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time.
➢
To remove after images on the screen, use either “All White” or “Signal Pattern” function.
Although both of the two functions remove after images on the screen, “Signal Pattern” is more effective.
➢
The after image removal function has to be executed for a long time (approximately 1 hour) to effectively remove after images on the screen.
If after image is not improved after the execution of the function, repeat the function again.
➢
Press any button on the remote control to cancel this feature.
English - 25
Setting the Blue Eye
You can set the power of Blue LED to be on. If the power is off when Blue Eye is off, the Blue LED goes off after 5 seconds. This will save power and reduce eye fatigue.
TV Setup
More
Energy Saving : Off
Screen Burn Protection
Blue Eye : On
Move Enter Return
1 Press the MENU ( ) button to display the menu.
2 Press the … or † button to select Setup, then press the ENTER (
3 Press the … or † button to select Blue eye, then press the ENTER ( button.
) button.
)
4 Select Off or On by pressing the … or † button, then press the ENTER
( ) button.
◆ Off: LED(Blue) will not come on.
◆ On: LED(Blue) will come on after you turn the TV off.
5 Press the EXIT button to exit.
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1 Right click the mouse on the Windows Desktop, then click on Properties.
The Display Properties will be displayed.
2 Click on Settings tab, then set the Display Mode with reference to the
Display Modes Table. You do not need to change the Colours settings.
3 Click on Advanced. A new settings dialog box will be displayed.
4 Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes Table.
Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen refresh rate.
5 Click on OK to close the window, then Click on OK button to the Display
Properties window. Automatic re-booting may commence at this moment.
English - 26
Input Mode (PC)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Video Signal
IBM PC / AT
Compatible
Resolution
(Dot X Line)
640 x 350
720 x 400
640 x 480
800 x 600
848 x 480
1024 x 768
1280 x 720
1360 x 768
Vertical frequency
(Hz)
70.086
70.087
59.940
70.000
72.809
75.000
56.250
60.317
70.000
72.188
75.000
60.000
74.769
60.004
70.069
72.000
75.029
59.855
60.015
Horizontal frequency
(kHz)
31.469
31.469
31.469
35.000
37.861
37.500
35.156
37.879
43.750
48.077
46.875
31.020
37.684
48.363
56.476
57.672
60.023
44.772
47.712
Vertical polarity
P
N
P
P
N
N
N/P
N
N
N/P
P
N/P
P
P
P
P
N
N
N/P
N/P
P
N/P
P
N
P
N
N/P
N
N
N
N
N
P
P
N/P
P
P
P
Horizontal polarity
PS-42Q7HD PS-50Q7HD
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
(N: Negative / P: Positive)
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
◆ The interlace mode is not supported.
◆ The television might operate abnormally if a non-standard video format is selected.
◆ 480i/p, 576i/p, 720p, or 1080i is not available in PC mode.
◆ The PC text quality is optimum in XGA mode (1024 x 768@60Hz). (PS42Q7HD)
◆ The PC text quality is optimum in WXGA mode (1360 x 768@60Hz). (PS50Q7HD)
English - 27
Setting the PC
➢
Preset to the PC mode by pressing the SOURCE ( ) button.
TV Setup 1 Press the MENU ( ) button to display the menu.
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
More
Move
: English
: Off
: Off
: Off
Enter Return
2 Press the … or † button to select Setup, then press the ENTER (
3 Press the … or † button to select PC, then press the ENTER (
) button.
) button.
4 Select the required option by pressing the … or † button, then press the
ENTER ( ) button.
TV
Available options: Image Lock, Position, Auto Adjustment, Image Reset
Image Lock
Position
Auto Adjustment
Image Reset
PC
5 When you are satisfied with your setting, press the ENTER ( ) button.
6 Press the EXIT button to exit.
Move Enter Return
TV
TV
Coarse
Fine
Move
Image Lock
Enter
Position
50
60
Return
◆ Image Lock: Coarse/Fine
The purpose of picture quality adjustment is to remove or reduce picture noise.
If the noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible (coarse) and Fine-tune again.
After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen.
1 Press the … or † button to select Coarse or Fine, then press the
ENTER ( ) button.
2 Press the œ or √ button to adjust the screen quality, vertical stripes may appear or the picture may be blurry. Press the ENTER ( ) button.
◆ Position:
Adjust the PC’s screen positioning if it does not fit the TV screen.
1 Adjust the position by pressing the …/†/œ/√ button.
2 Press the ENTER ( ) button.
Move Enter Return
Auto Adjustment in progress
Please wait
Image Reset has completed.
Return
◆ Auto Adjustment:
Auto adjustment allows the PC screen of set to self-adjust to the incoming
PC video signal.
The values of fine, coarse and position are adjusted automatically.
◆ Image Reset:
You can replace all image settings with the factory default values.
English - 28
Previewing the DTV Menu System
To help you navigate around the on-screen menu system and adjust the various settings available, refer to the following illustration.
➢
Available in the Digital TV mode.
Press the “D.MENU” button.
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide Now/Next
Full Guide
Preference
Translucency level
Parental Lock
Feature
Subtitle On
Off
Subtitle Language
Audio Language: : English
Audio Format
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel Manager
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
High
Medium
Low
Opaque
Parental Rating No Block
Block G
Block PG
Change PIN
Block M
Block MA
Block AV
Block R
Block All
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
: Full Guide
Move Enter Exit
Press ENTER to display the Electronic
Programme Guide Options.
Preference
Translucency level: Medium
Parental Lock
Move Enter Exit
Press ENTER to change your preferences.
Feature
Subtitle
Subtltle Language
Audio Language
Audio Format
: On
: English
: MPEG
Move Enter Exit
Press ENTER to view the feature options.
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel Manager
Move Enter Exit
Press ENTER to change the channel settings.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
Move Enter
Press ENTER to view the system options.
Exit
English - 29
Updating the Channel Manager Automatically
You can update the channel list when the broadcaster adds new Services or if you move the TV to a new location.
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel Manager
Move Enter Exit
Press ENTER to change the channel settings.
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel Manager
Move Enter Return
Press ENTER to update your list of channels.
1 Press the D.MENU button to display the DTV menu.
2 Press the … or† button to select Channel.
Press the ENTER ( ) button.
The options available in the Channel group are displayed.
3 Press the ENTER ( ) button.
The Auto Store is selected. The channel search will start and end automatically.
4 When it has finished, the number of scanned services will be displayed.
➢
The existing favourite channel list will be deleted when the channel list is updated.
➢
To stop the scan before it has finished, press the ENTER ( ) button with STOP selected.
5 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
➢
If the signal status is poor, the “No Service found! Check the aerial
connection” message is displayed.
Auto Store
Scanning for digital services...
0%
Services found:6 Channel:33
Stop
Return
The channel list is being updated.
To abort the scan press D.MENU.
Auto Store
Scanning for digital services...
100%
Services found:6 Channel:33
Update channel list...
Return
The channel list is being updated.
To abort the scan press D.MENU.
English - 30
Updating the Channel Manager Manually
You can update the channel list when the broadcaster adds new Services or if you move the TV to a new location.
1 Press the D.MENU button to display the DTV menu.
2 Press the … or† button to select Channel.
Press the ENTER ( ) button.
The options available in the Channel group are displayed.
3 Press the … or† button to select Manual Store.
4 To... Then...
Move to Channel, Frequency, or Bandwidth œ or √ button
Set the Channel, Frequency, or Bandwidth … or † button
➢ ◆ Channel : Channel "6" to "12" and "27" to "69" in sequence are dis played.
◆ Frequency : The frequency available in the Channel group is displayed.
◆ Bandwidth : UHF 7MHz.
5 Press the red button to start the scan for digital services.
When it has finished,channels are updated in the channel list.
6 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
➢
You can input by pressing the number buttons on the remote control.
➢
You can not change only Frequency and when changing a channel, the
Frequency will be automatically changed.
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel Manager
Move Enter Exit
Press ENTER to change the channel settings.
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel Manager
Move Enter Return
Press ENTER to manually update your list of channels.
Manual store
Channel Frequency
6
177500 KHz
Bandwidth
7 MHz
Search
Adjust Move Return
Press UP/DOWN to adjust the channel number or LEFT/RIGHT to move between fields.
Manual store
Channel Frequency
6 177500
KHz
Bandwidth
7 MHz
0 .. 9
Search
Enter freq.
Move Return
Press the digits to enter the frequency or LEFT/RIGHT to move between fields
Manual store
Channel Frequency
6 177500 KHz
Bandwidth
7
MHz
Search
Adjust Move Return
Press up/DOWN to adjust the bandwidth or LEFT/RIGHT to move between fields
English - 31
Editing Your Favourite Channels
You can edit your favourite channels using the four colour buttons.
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel Manager
Move Enter Return
Press ENTER to edit your favourite channels.
Edit Favourite Channels
(no Channels)
Add Channels
Return
The list of favourite channels is empty.
Press RED to add channel.
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select Channel.
Press the ENTER ( ) button.
The options available in the Channel group are displayed.
3 Press the … or † button to select Edit Favourite Channels.
4 Press the ENTER ( ) button.
The Edit Favourite Channels menu is displayed.
5 Press the Red button to add channels to the favourite channel list.
6 Press the … or † button to select the required channel.
7 Press the ENTER ( ) button.
A “*” icon is shown next to the selected channel and the channel will be added to the favourite channel list.
To undo, press the ENTER ( ) again.
➢ ◆ Select All- Select all channels currently displayed.
◆ Select None- Deselect all selected channels.
◆ Preview- Displays (a) currently selected channel(s).
The Favorite Channels settings have been completed.
8 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
Edit Favourite Channels
800 RaiDue
801 RaiTre
802 RaiUno
Select All
Move
Select None
Select
Preview
Return
Press ENTER to add the channel to the favourites List.
English - 32
Editing Your Favourite Channels (continued)
◆ Add
1 Press the D.MENU button.
The DTV menu is displayed.
2 Press the … or † button to select Channel.
Press the ENTER ( ) button.
The options available in the Channel group are displayed.
3 Press the … or † button to select Edit Favourite Channels.
4 Press the ENTER ( ) button.
5 Press the red button in the Edit Favourite Channels menu.
The Edit Favourite Channels menu is displayed.
6 Press the … or † button to select the required channel.
7 Press the ENTER ( ) button.
A “*” icon is shown next to the selected channel and the channel will be added to the favourite channel list.
To undo, press the ENTER ( ) again.
➢
◆ To add all channels to the favourite channel list, press the red button.
◆ To remove all channels, press the green button.
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel Manager
Move Enter Return
Press ENTER to manually update your list of channels.
Edit Favourite Channels
(no Channels)
Add Channels
Return
The list of favourite channels is empty.
Press RED to add channels.
Edit Favourite Channels
800 RaiDue
801 RaiTre
802 RaiUno
Select All
Move
Select None
Select
Preview
Return
Press ENTER to add the channel to the favourites List.
Edit Favourite Channels
800 RaiDue
801 RaiTre
802 RaiUno
Add
Move
Move Preview Delete
Return
The list of favourite channels is shown above. Highlight a channel and choose an option.
Edit Favourite Channels
800 RaiDue
801 RaiTre
802 RaiUno
Select All
Move
Select None
Select
Preview
Return
Press ENTER to remove this channel from the favourites list.
English - 33
Editing Your Favourite Channels (continued)
Edit Favourite Channels
800 RaiDue
801 RaiTre
802 RaiUno
Add
Move
Drop Preview Delete
Return
Move the channel using the up and down keys. press GREEN again to drop channel.
◆ Move
1 In the Edit Favourite Channels menu, select the required channel using the
… or † button.
2 Press the green button.
A “ ”icon is displayed on the left side of the channel name.
3 Press the … or † button to select the channel that you want to move, and press the green or ENTER ( ) button.
The channel is moved to its new position.
Edit Favourite Channels
800 RaiDue
801 RaiTre
802 RaiUno
◆ Preview
1 In the Edit Favourite Channels menu, select the channel to be previewed by pressing the … or †button.
2 Press the yellow button.
The selected channel is displayed on the screen.
Add
Move
Drop Preview Delete
Return
The list of favourite channels is shown above. Highlight a channel and choose an option.
◆ Delete
1 In the Edit Favourite Channels menu, select the channel to be previewed by pressing the … or †button.
2 Press the blue button.
The selected channel and number will be deleted.
➢
To add a deleted channel back into the favourite channel list, see 'Add' on page 33.
English - 34
Selecting Channel Manager
You can exclude the channels you have chosen from the channels you scanned.
When you scan through the stored channels, those you have chosen to skip are not displayed.
All channels that you do not specifically chose to skip are displayed during scanning.
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select Channel.
The options available in the Channel group are displayed.
3 Press the ENTER ( ) button.
4 Press the … or † button to select Channel Manager.
Press the ENTER ( ) button.
The channel manager is displayed.
5 Press the D.MENU or EXIT button to return to normal viewing.
Channel
Auto Store
Manual Store
Edit Favourite Channels
Channel Manager
Move Enter Return
Press ENTER to start the current channel manager
Channel Manager
BBC ONE
1 BBC ONE
2 BBC TWO
7 BBC THREE
30 CBBC Channel
40 BBC NEWS 24
51 BBCi
800 DTG-TV 1
800 DTG-TV 2
802 DTG-TV3
803 P05 Streams
804 P07 Engine
805 P10 Receiver
806 P12 Names
Previous page
Move
Next Page
Watch
All Channels
Favourites Exit
Return
Viewing Channel Lists
You can display a list of all channels or your favourite channels.
1 Press the CH.MGR button.
The channel manager is displayed.
2 To toggle between your favourite channels and all channels, use the yellow button.
➢
Your favourite channels are only displayed if they were previously set in the
Edit Favourite Channels menu. (refer to page 32~34)
3 Move to the channel of your choice by pressing the … , †, œ or √ button.
4 To tune to the selected channel, press the ENTER ( cursor is on the selected channel.
) button while the
➢
The channel number, name and an icon are displayed in the top left corner while changing the channel.
The channel number and name are displayed if the channel is one of the all channels, and a “
★
” icon if the channel is one of the favourite channels.
5 To exit from the channel list, press the CH.MGR button.
Channel Manager
All Channels BBC ONE
1 BBC ONE
2 BBC TWO
7 BBC THREE
30 CBBC Channel
40 BBC NEWS 24
51 BBCi
800 DTG-TV 1
800 DTG-TV 2
802 DTG-TV3
803 P05 Streams
804 P07 Engine
805 P10 Receiver
806 P12 Names
Previous page
Move
Next Page
Watch
Favourites
Exit
Exit
English - 35
Displaying Programme Information
While viewing a channel, additional information about the current programme may be displayed.
1 While viewing a programme, press the INFO button.
The programme information is displayed.
2 To exit from banner information, press the INFO button.
70 7 HD Digital
14:30 Sat 1 Sep
All Channels A
NO Information
INFO Exit
English - 36
Viewing the EPG (Electronic Programme Guide) Information
You can display EPG information at any time while watching digital programmes.
➢
The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out of date as a result of the information broadcast on a given channel.
The display will dynamically update as soon as new information becomes available.
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
: Full Guide
Move Enter Return
Press ENTER to start the Now & Next
Guide.
◆ Now & Next Guide
For the six channels indicated in the left-hand column, displays the Current programme and the Next programme information.
[Now & Next Guide]
◆ Full Guide
Displays the programme information as time ordered hour segments.
Two hours of programme information is displayed which may be scrolled forwards or backwards in time.
1 Press the D.MENU button.
The options available in the Guide group are displayed.
2 Press the ENTER ( ) button.
3 Select the your required guide (Now & Next Guide or Full Guide)by pressing the … or † button.
4 Press the ENTER ( ) button.
The selected guide menu is displayed.
➢
You can also display the guide menu simply by pressing the GUIDE button.
Press the red button to toggle between the Now & Next Guide and the Full
Guide.
[Full Guide]
English - 37
Viewing the EPG (Electronic Programme Guide) Information(continued)
5 To... Then...
Display the
Now & Next Guide and the Full Guide
◆ Press the red button.
◆ Press the red button again to toggle between the Now &
Next Guide and the Full
Guide.
Display the Favourites list and the All Channels manager
◆ Press the green button.
◆ Press the green button again to toggle between the Favourites and the All Channels manager.
Scrolls backwards quickly (2 hours).
◆ Press the yellow button.
Scrolls forward quickly (2 hours).
◆ Press the blue button.
Exit the guide
Watch a programme in the EPG list
View programme information
◆ Press the Exit button.
◆ Select a programme by pressing the … , †, œ or √ button.
◆ Press the ENTER ( )button.
◆ Select a prgramme of your choice by pressing the … , †, œ or √ button.
◆ Press the INFO button when programme of your choice is highlighted.
6 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
➢
◆ The programme title is on the upper part of the screen center.
Please click on INFO button for the detailed information.
Channel Number, Running Time, Status Bar, Parental Level, Video
Quality Information(HD/SD), Sound Modes, Subtitle or Teletext,
Languages of Subtitle or Teletext, and brief summary of the highlighted programme are included on the detailed information. "..." will be appeared if the summary is long.
◆ Six channels are displayed. To scroll between channels,move to a channel using the … or † button.
To display page by page, use the P or P button.
English - 38
Using the Scheduled List
If you make a scheduled viewing list of programs you may like to see, the channel will be automatically switched to the scheduled program at the scheduled time even if you are watching another program.
1 Press the D.MENU button.
The options available in the Guide group are displayed.
2 Press the ENTER ( ) button.
3 Select the Scheduled List by pressing the … or † button.
4 Press the ENTER ( ) button.
The selected guide menu is displayed.
5 Press the red button.
The channel will be switched to the scheduled program.
6 Press the ENTER (
√ or number button .
) button to move to an item and adjust with … , †, œ
◆ Channel: Set the channel.
◆ Time: Set the time.
◆ Date: Set Year, Month and Day.
◆ Frequency: Set the frequency.
7 After setting the schedule, Press the red button.
The schedule will be displayed.
8 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
➢
The Scheduled list may be displayed in the EPG menu.
➢
Save: Save the adjusted schedule.
Cancel: Cancel the adjusted schedule.
Add Programme: Add a new schedule.
Edit: Re-adjust the selected schedule.
Delete: Delete the selected schedule.
➢
You can also set hour and minute by pressing the number buttons on the remote control.
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
: Full Guide
Move Enter Return
Press ENTER to view a list of scheduled events.
Scheduled List
(no Programmes)
Add Programme
Return
There are no scheduled programmes.
Press RED to add a new programme.
Scheduled List
Channel 802 RaiUno
Time
Date
Frequency
Tue 22 Apr 2008
Once
Save
Adjust Move
Cancel
Return
Press UP/DOWN to adjust the channel.
Scheduled List
Tuesday 22 Apr 15:30~16:00 once
801/ Raiire
Add Programme
Move Return
Edit Delete
Press RED to add a new programme or
BLUE to delete selected programme.
English - 39
Setting the Default Guide
You can preset the default guide style.
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
: Full Guide
1 Press the D.MENU button.
The options available in the Guide group are displayed.
2 Press the ENTER ( ) button.
Move Enter Return
Press ENTER to choose the default
Guide style.
3 Select to the Default Guide by pressing the … or † button.
4 Press the ENTER ( ) button.
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide :
Now/Next
Full Guide
5 Select Now & Next or Full Guide using the … or † button, and press the
ENTER ( ) button.
The selected option is stored and the preset/default channel list in the EPG menu will be displayed.
Move Enter Return
Press ENTER to choose the default
Guide style.
6 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
➢
You can select these options by simply pressing the GUIDE button on the remote control.
English - 40
Viewing AII Channels and Favourite Channels
In the EPG menu, you can display all channels or favourite channels.
1 Press the D.MENU button.
The options available in the Guide group are displayed.
2 Press the ENTER ( ) button.
3 Select the your required guide (Now & Next Guide or Full Guide) by pressing the … or † button.
4 Press the ENTER ( ) button.
The selected guide menu is displayed.
5 Press the green button.
All the channel lists and the favorite channel lists will be toggled.
To toggle between the all and favourite channels list, press the green button again.
6 Select a programme of your choice by pressing the … , †, œ or √ button.
7 Press the INFO button to display information about the highlighted programme.
Available programme information is displayed.
8 When the favourite channel list has not been set up:
◆ The favourites list is empty. Would you like to choose your favourites now?” message is displayed.
◆ Select “Yes”.
The Favourite Channels menu is displayed.
If you select “No”, all channels will remain unchanged.
◆ To edit the favourite channels, refer to page 32~34 for more details.
9 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
➢ ◆ All Channels is the list of channels that have been scanned by the channel list update. All channels are displayed in the all channel mode.
◆ Favourites (favourite channels) is the list of channels that has been set in the Favourite Channels menu (refer to page 32~34).
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
: Full Guide
Move Enter Return
Press ENTER to start the Now & Next
Guide.
English - 41
Adjusting the Translucency Level
You can set the translucency level of menu.
Preference
Translucency level: Medium
Parental Lock
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select Preference.
The options available in the Preference group are displayed.
3 Press the ENTER ( ) button.
Move Enter Exit
Press ENTER to change your preferences.
4 Select to the Translucency Level by pressing the ENTER (
The options of the selected menu available are displayed.
Preference
Translucency level: Medium
Parental Lock
) button.
5 Select the required option by pressing the … or † button, and press the
ENTER ( ) button to change the setting.
6 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
Move Enter Return
Press ENTER to choose graphics translucency .
Preference
Translucency level:
Parental Lock
High
Medium
Low
Opaque
Move Enter Return
Press ENTER to choose graphics translucency .
English - 42
Setting up the Parental Lock
This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by a
4-digit PIN (Personal Identification Number) code that is defined by the user. The on-screen menu will instruct you to assign a PIN code (you can change it later, if necessary).
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select Preference.
The options available in the Preference group are displayed.
3 Press the ENTER ( ) button.
4 Press the … or † button to select Parental Lock.
Press the ENTER ( ) button.
The Enter PIN is displayed.
5 Enter your current 4-digit PIN code by using the numeric buttons (0~9).
The options available in the Parental Lock group are displayed with the
Parental Rating selected.
➢
◆ The default PIN code for a new TV set is 0000 .
◆ If you enter an invalid PIN code,the Invalid PIN code.
Please try again. message is displayed.
6 Press the ENTER ( ) button.
7 Press the … or † button to select the age rating you want to lock out.
Press the ENTER ( ) button.
8 If you want to change the PIN code,select Change PIN by pressing the … or
† button. Press the ENTER ( ) button.
The Enter New PIN is displayed.
9 Enter your new PIN code by using the numeric buttons (0~9).
The Confirm New PIN is displayed.
Preference
Translucency level: Medium
Parental Lock
Move Enter Return
Press ENTER to change the Parental Lock settings.
Parental Lock
Enter PIN
0 .. 9 Enter PIN Return
Use the NUMBER buttons to enter your
PIN code.
Parental Lock
Parental Rating : No Block
Change PIN
Move Enter Return
Modify the parental ratings you want to lock out
Parental Lock
Parental Rating :
Change PIN
No Block
Block G
Block PG
Block M
Block MA
Block AV
Block R
Move Enter Return
Modify the parental ratings you want to lock out.
Parental Lock
Parental Rating : No Block
Change PIN
Move Enter Return
Press ENTER to change the PIN code.
Change PIN
Enter New PIN
0 .. 9 Enter PIN Return
Enter a new PIN code.
English - 43
Setting up the Parental Lock (continued)
Change PIN
Confirm New PIN
10 Re-enter your new PIN code to confirm by using the numeric buttons (0~9).
The Your PIN code has been changed successfully message is displayed.
0 .. 9 Enter PIN Return
Enter the new PIN code again to confirm.
Change PIN
Confirm New PIN
11 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
➢
If you forget the PIN code, press the remote control buttons in the following sequence, which resets the PIN to 0-0-0-0 : POWER (Off), MUTE, 8, 2,
4, POWER (On)
You PIN code has been changed successfully.
OK
0 .. 9 Enter PIN Return
Enter the new PIN code again to confirm.
Setting the Subtitle
You can activate or deactivate the subtitle.
Feature
Subtitle
Subtltle Language
Audio Language
Audio Format
: Off
: English
: MPEG
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select Feature.
The options available in the Feature group are displayed.
3 Press the ENTER ( ) button.
Move Enter Exit
Press ENTER to view the feature options.
4 Press the ENTER ( ) button.
5 Select On by pressing the … or † button.
Press the ENTER ( ) button.
Feature
Subtitle
Subtltle Language
Audio Language
Audio Format
: Off
: English
: MPEG
6 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
Move Enter Return
Press ENTER to turn Subtitles on or off.
Feature
Subtitle
Subtltle Language
Audio Language
Audio Format
: Off
Off
On
: English
: MPEG
Move Enter Return
Press ENTER to turn Subtitles on or off.
English - 44
Selecting the Preferred Language (Subtitle or Audio)
You can change the default value for subtitle and audio languages.
Displays the language information for the incoming stream.
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select Feature.
The options available in the Feature group are displayed.
3 Press the ENTER ( ) button.
4 Select your required menu (Subtitle Language or Audio Language) by pressing the … or † button, and press the ENTER ( ) button.
The options of the selected menu available are displayed.
5 Select the required option (English) by pressing the … or † button, and press the ENTER ( ) button to change the setting.
➢
English is the default in cases where the selected language is unavailable in the broadcast.
6 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
➢
While viewing a programme, the subtitle can be selected.
While viewing a programme, audio languages can be selected.
Feature
Subtitle
Subtltle Language
Audio Language
Audio Format
: On
: English
: MPEG
Move Enter Exit
Press ENTER to view the feature options.
Feature
Subtitle
Subtltle Language
Audio Language
Audio Format
: On
: English
: MPEG
Move Enter Return
Press ENTER to choose your preferred
Subtitle Language.
Feature
Subtitle
Subtltle Language
Audio Language
Audio Format
: On
: English
: MPEG
Move Enter Return
Press ENTER to choose your preferred
Audio Language.
English - 45
Selecting the Audio Format
You can preset the default guide style.
Feature
Subtitle
Subtltle Language
Audio Language
Audio Format
: On
: English
: MPEG
1
2
Press the D.MENU button to display the DTV menu.
Press the … or † button to select Feature.
The options available in the Feature group are displayed.
3 Press the ENTER ( ) button.
Move Enter Exit
Press ENTER to view the feature options.
4 Press the … or † button to select Audio Format.
Press the ENTER ( ) button.
Feature
Subtitle
Subtltle Language
Audio Language
Audio Format
: On
: English
: MPEG
5 Select the required option by pressing the … or † button, and press the
ENTER ( ) button to change the setting.
6 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
Move Enter Return
Press ENTER to select preferable audio format between MPEG and Dolby Digital.
English - 46
Selecting the Time Zone
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select System.
The options available in the System group are displayed.
Press the ENTER ( ) button.
3 Press the… or † button to select Time Zone.
Press the ENTER ( ) button.
4 Select the time zone where you locate by pressing the … or † button.
Press the ENTER ( ) button.
The following options are available.
New South Wales/ACT - Victoria - Queensland - South
Australia - Western Australia - Tasmania - Northern
Territory
5 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
Guide
Now & Next Guide
Full Guide
Scheduled List
Default Guide
: Full Guide
Move Enter Exit
Press ENTER to display the Electronic
Programme Guide Options.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
Move Enter Exit
Press ENTER to view the system options.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
Move Enter Return
Press ENTER to show the product information.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
Move Enter Return
Press ENTER to select your Time Zone
Time Zone
New South Wales/ACT
Victoria
Queensland
South Australia
Western Australia
Tasmania
Northern Territory
Adjust Select Return
Select the Time Zone where you locate
Time Zone
New South Wales/ACT
Victoria
Queensland
South Australia
Western Australia
Tasmania
Northern Territory
Adjust Select Return
Select theTime Zone where you locate
English - 47
Viewing Product Information
You can view your product information. For service or repair, please contact a Samsung approved dealer.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select System.
The options available in the System group are displayed.
Move Enter Exit
Press ENTER to view the system options.
3 Press the ENTER ( ) button.
The Product Information menu is selected.
4 Press the ENTER ( ) button.
The Product Information menu is selected.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
- Product Name
- Software Version
5 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
Move Enter Return
Press ENTER to show the product information.
Product Information
Product Name: JAGUAR2
Software version:T-JAGU2DAUO-****
Return
The product information details are shown above. Press D.MENU to return.
Checking the Signal Information
You can get information about the signal status.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
Move Enter Exit
Press ENTER to view the system options.
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select System.
Press the ENTER ( ) button.
The options available in the System group are displayed.
3 Press the… or † button to select Signal Information, and press the ENTER
( ) button.
The technical information for signal status is displayed.
4 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
➢
If the signal status is poor, the “No signal.” message is displayed.
Move Enter Return
Press ENTER to display the signal information on the current channel.
Signal Information
Service: 7 Digital
Service ID: 0530, running
Multiplex: 43C (TSID 0503, ONID 1013)
Network: Test Card 'M'..(ID 321ff)
Bit error level: 0
Signal Strength: 70
Return
The signal information on the current service is shown above. Press D.MENU to return.
English - 48
Upgrading the Software (Option)
To keep your product up-to-date with new Digital Television features then software upgrades are periodically broadcast as part of the normal
Television signal. It will automatically detect these signals and display the software upgrade banner.
After downloading is finished, when changing the channel or repowering the television, the message box will appear on the screen.
While downloading, it's better to keep the current channel to make sure entirely downloading. It will not take too much time. If you change the channel, the downloading will continue when you change back.
You are given the option to install the upgrade.
◆ Upgrade Now
If you select Upgrade Now, the iDTV immediately installs the new upgrade and then restarts.
◆ Upgrade Later
If you select Upgrade Later, the upgrade is postponed until the next restart or channel change some 90 minutes later, when the upgrade dialog appears again.
◆ Don’t Upgrade
If you select Don’t Upgrade, the iDTV does not perform the upgrade and the software upgrade banner is not displayed again.
The upgrade is still stored internally, to subsequently upgrade to the new version then the following sequence of steps are performed.
Alternatively, you can manually upgrade the software.
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select System.
Press the ENTER ( ) button.
The options available in the System group are displayed.
3 Press the … or † button to select Software Upgrade, and press the
ENTER ( ) button.
The software upgrade information is displayed.
4 To switch to an alternative version, press the red button.
Press the blue button to reset, activate the upgrade and restart.
5 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
Software Upgrade
Current Software: T-JAGU2DAUO_****
Default
Alternative Software:
Downloading...
Return Info
The software versions available are shown above. There are no upgrade options available.
Software Upgrade
An upgrade is available for your TV and is ready for installation.
Upgrade Now Upgrade Later Don’t Upgrade
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
Move Enter Exit
Press ENTER to view the system options.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
Move Enter Return
Press ENTER to view the software upgrade information.
Software Upgrade
Current Software: T-JAGU2DAUO_****
Default
Alternative Software: T-JAGU2DAUO_****
(New version)
Switch Default Software
Move Return Info
The software versions available are shown above. Press RED to switch the default.
Software Upgrade
Current Software: T-JAGU2DAUO_****
Default
Alternative Software: T-JAGU2DAUO_****
(New version)
Switch Default Software
Move Return Info
The software versions available are shown above. Press RED to switch the default.
Software Upgrade
Current Software: T-JAGU2DAUO_****
Default
Alternative Software: T-JAGU2DAUO_****
(New version) New Default
Move Return
Confirm
Info
Press BLUE to confirm the switch.
English - 49
Resetting
You can reset the values stored to the factory default values.
➢
The Reset operation deletes all channel information and user preferences returning all values to their default factory state.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
1 Press the D.MENU button to display the DTV menu.
2 Press the … or † button to select System.
Press the ENTER ( ) button.
The options available in the System group are displayed.
Move Enter Exit
Press ENTER to view the system options.
3 Press the … or † button to select Reset, and press the ENTER ( button.
The technical information for signal status is displayed.
The Enter PIN screen will appear.
System
Product Information
Signal Information
Time Zone
Software Upgrade
Reset
3
)
Enter your current 4-digit PIN code by using the numeric buttons (0~9).
The warning message is displayed.All values will be reset by pressing the coloured buttons (red,green, yellow,and blue) in turn.
Move Enter Return
Press ENTER to navigate to the reset confirmation screen.
4 Press the D.MENU button to return to the previous menu or press the EXIT button to return to normal viewing.
Enter PIN
Reset
0 .. 9 Enter PIN Return
Use the NUMBER buttons to enter your
PIN code.
System
WARNING: All channel settings and user preferences will be lost and returned to the factory defaults.
It is recommended that a reset is performed only when serious problems are experienced.
Return
Press RED, GREEN, YELLOW and BLUE in sequence to confirm the reset process.
English - 50
Teletext Feature
(depending on the model)
Most television stations provide written information services via teletext.
The index page of the teletext service gives you information on how to use the service. In addition, you can select various options to suit your requirements by using the remote control buttons.
☛
For teletext information to be displayed correctly, channel reception must be stable. Otherwise, information may be missing or some pages may not be displayed.
(teletext on/mix)
Press to activate teletext mode after selecting the channel providing the teletext service. Press it twice to overlap the teletext with the current broadcasting screen.
(sub-page)
Used to display the available sub-page.
(hold)
Used to hold the display on a given page if the selected page is linked with several secondary pages which follow on automatically.
To resume, press it again.
(size)
Press to display the double-size letters in the upper half of the screen. For lower half of the screen, press it again.
To display normal screen, press it once again.
(store)
Used to store the teletext pages.
(mode)
Press to select the teletext mode (LIST/FLOF). If you press it in the
LIST mode, it switches into the List save mode. In the List save mode, you can save teletext page into list using the button.
(store)
(page up)
Used to display the next teletext page.
(page down)
Used to display the previous teletext page.
(index)
Used to display the index (contents) page at any time while you are viewing teletext.
(reveal)
Used to display the hidden text (answers to quiz games, for example). To display normal screen, press it again.
(cancel)
Used to display the broadcast when searching for a page.
(exit)
Exit from the teletext display (depending on the model)
➢
You can change teletext pages by pressing the numeric buttons on the remote control.
continued...
English - 51
Teletext Feature
(depending on the model)
The teletext pages are organized according to six categories:
Part
A
B
C
D
E
F
Contents
Selected page number.
Broadcasting channel identity.
Current page number or search indications.
Date and time.
Text.
Status information.
FASTEXT information.
➢
Teletext information is often divided between several pages displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
➢
Press the TV/DTV button to exit from the teletext display.
English - 52
How to Install the Wall Mount Bracket
➢
This installation guide may be different from the PDP User’s manual.
Please refer to the proper installation guide for your product.
Installation Notes
◆ Contact a technician for installing the wall bracket.
◆ Samsung Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer.
◆ This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
◆ The package contents and parts supplied for the wall mount are subject to change without prior notice.
Mounting Kits
◆ Please use only the parts and components provided for wall mount installation.
Wall Mount Bracket ASSY-HINGE Screws
Plastic Hanger : 4 EA
1EA LEFT :1EA RIGHT :1EA SCREW : 4 EA
How to assemble the Wall Mount Bracket
1 The wall mount bracket is delivered separately.
Please tighten the captive screw in the direction of the arrow after assembling the bracket.
Install the Wall Mount Bracket after the screws are securely inserted into the wall.
ASSY-HINGE
(LEFT)
Captive Screws
Wall Mount Bracket
Separate ASSY-HINGE into Left and Right.
ASSY-HINGE
(RIGHT)
Instructions on Securing the SET to the Wall Mount Bracket
➢
The exterior of the SET may be different than the picture. (Assembly and installation of the plastic hanger is the same.)
1 Remove the screws from the back of the PDP.
2 Use the screw and assemble the plastic hanger.
(Please refer to the following picture.) continued...
☛
1 Please ask the installers to install the wall mount bracket.
2 Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the SET on the wall mount bracket.
3 Please avoid catching your fingers while installing and adjusting the angle.
4 Please tightly secure the wall mount bracket to the wall to avoid injury from a falling SET.
English - 53
How to Install the Wall Mount Bracket
3 Tighten the screws of the plastic hanger (shown in picture 2) to the back side of the PDP.
4 Remove the Safety Pins. Fasten the 4 plastic latches assembled at step (#) on the back side of the PDP using the guide holes of the wall mount, push (!) and hook (@) down to secure the PDP on the wall mount as illustrated. Secure the PDP by inserting the Safety Pins, not to fall from the wall mount.
PDP panel
Wall attachment panel bracket
Wall
How to Adjust Mounting Angle
➢
Please secure the mounting bracket on the wall surface after setting its angle at 0°
1 Secure the SET to the wall mount bracket.(Please refer to the follow ing instructions.)
2 Set the angle by pulling the upper end of the SET attached to bracket in the direction of the arrow. (Refer to the illustration on the right.)
3 The angle can be adjusted from 0° to 15° by ±2°.
Hold onto the middle of the PDP to adjust the angle (not the sides of the PDP).
Connecting External Devices to the PDP
➢
To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following instructions:
1 Be sure to remove the safety pins underneath the PDP.
➢
If the safety pins are not removed, the angle cannot be adjusted. Any attempt to do so may cause damage to the PDP.
2 Hold onto the bottom of the PDP and pull forward fully as directed by the arrow as illustrated) to adjust the angle.
(0°~20° by 2°) Insert the Safety Pins to the front guide holes on both sides as illustrated in figure @.
➢
Viewing the PDP after connecting the external devices
Remove the Safety Pins to adjust the angle to 0°, and then secure the Safety Pins again.
☛
For safety, be sure to secure the PDP using the safety pins. If the safety pins are not used, the PDP may fall, causing serious injury.
English - 54
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer.
No sound or picture
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the (Power) button (On/Off) on the front panel or press the POWER ( ) button on the remote control.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
◆ Check if Internal Mute is set to ON.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume MUTE button on the remote control has been pressed.
No picture or black and white picture
◆ Adjust the colour settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the television, then move it further away.
◆ Plug the television into a different mains socket.
Blurred or snowy picture, distorted sound
◆ Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check that the “+” and “–” ends of the batteries are inserted correctly.
◆ Check that the batteries are drained.
Screen is black and power indicator light blinks steadily
◆ On your computer check; Power, Signal Cable.
◆ The TV is using its power management system.
◆ Move the computer’s mouse or press any key on the keyboard.
◆ On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
◆ The TV is using its power management system.
◆ Press the Source button on the panel or remote control.
◆ Turn the TV off and on.
English - 55
This page is intentionally left blank.
This page is intentionally left blank.
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Country
AUSTRALIA
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
PHILIPPINES
SINGAPORE
SOUTH AFRICA
TAIWAN
THAILAND
U.A.E
VIETNAM
Customer Care Centre
1300 362 603
800-810-5858, 010- 6475 1880
2862 6001
3030 8282, 1600 1100 11
0800-112-8888
0120-327-527
1800-88-9999
1800-10-SAMSUNG (7267864)
1800-SAMSUNG (7267864)
0860 7267864 (SAMSUNG)
0800-329-999
1800-29-3232, 02-689-3232
800SAMSUNG (7267864)
1 800 588 889
Web Site www.samsung.com/au www.samsung.com.cn www.samsung.com/hk www.samsung.com/in www.samsung.com/id www.samsung.com/jp www.samsung.com/my www.samsung.com/ph www.samsung.com/sg www.samsung.com/za www.samsung.com/tw www.samsung.com/th www.samsung.com/mea www.samsung.com/vn
BN68-01080A-00
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 GENERAL INFORMATION
- 2 User Instructions
- 2 Checking Parts
- 3 Contents
- 5 Control Panel
- 5 Connection Panel
- 7 Viewing the Remote Control
- 8 Installing Batteries in the Remote Control
- 8 OPERATION
- 8 Switching Your Television On and Off
- 9 Viewing the Menus
- 9 Freezing the Current Picture
- 10 Plug & Play Feature
- 12 Viewing an External Signal Source
- 12 Editing Device Names
- 13 CHANNEL CONTROL
- 13 Storing Channels Automatically
- 14 Storing Channels Manually
- 15 Adding / Locking Channels
- 16 Sorting the Stored Channels
- 16 Assigning Names to Channels
- 17 Fine Tuning Channel Reception
- 18 PICTURE CONTROL
- 18 Changing the Picture Standard
- 18 Customizing the Picture Settings
- 19 Selecting the Picture Size
- 20 Digital NR / SMD / DNIe Demo
- 21 Viewing the Picture in Picture (PIP)
- 22 SOUND CONTROL
- 22 Sound Features
- 23 FUNCTION DESCRIPTION
- 23 Time Features
- 24 Language / Blue Screen / Melody / Energy Saving
- 24 Using Game Mode
- 25 Screen Burn Protection
- 26 Setting the Blue Eye
- 26 PC DISPLAY
- 26 Setting up Your PC Software (Based on Windows XP)
- 28 Setting the PC
- 27 Input Mode (PC)
- 29 USINGTHE DTV FEATURE
- 29 Previewing the DTV Menu System
- 30 Updating the Channel Manager Automatically
- 31 Updating the Channel Manager Manually
- 32 Editing Your Favourite Channels
- 35 Selecting Channel Manager
- 35 Viewing Channel Lists
- 36 Displaying Programme Information
- 37 Viewing the EPG (Electronic Programme Guide) Information
- 38 Viewing the EPG (Electronic Programme Guide) Information(continued)
- 39 Using the Scheduled List
- 40 Setting the Default Guide
- 41 Viewing AII Channels and Favourite Channels
- 42 Adjusting the Translucency Level
- 43 Setting up the Parental Lock
- 44 Setting up the Parental Lock (continued)
- 44 Setting the Subtitle
- 45 Selecting the Preferred Language (Subtitle or Audio
- 46 Selecting the Audio Format
- 47 Selecting the Time Zone
- 48 Viewing Product Information
- 48 Checking the Signal Information
- 49 Upgrading the Software (Option)
- 50 Resetting
- 51 USING THE TELETEXT FEATURE
- 51 Teletext Feature(depending on the model)
- 52 Teletext Feature(depending on the model)
- 53 APPENDIX
- 53 How to Install the Wall Mount Bracket
- 55 Troubleshooting