Samsung PS42B450B1M User manual

Add to my manuals
42 Pages

advertisement

Samsung PS42B450B1M User manual | Manualzz

Plasma TV user manual

BN68-02013A_Eng.indd 1

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at www.samsung.com/register

Model Serial No.

2009-09-18 �� 9:25:34

User Instructions

„

Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

„

Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.

„

Heat on the top of the PDP TV

The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.

„

The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.

„

Cell Defects

The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.

„

Avoid operating the TV at temperatures below 5°C(41°F)

„

A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

„

Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

„

-

-

Warranty

Warranty does not cover any damage caused by image retention.

Burn-in is not covered by the warranty.

„

Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Digital TV (DVB-T) Notice

1. Functionalities related to Digital TV(DVB) are only available in countries/areas where DVB-T (MPEG2 and MPEG4 AVC) digital terrestrial signals are broadcasted or where you have access to a compatible DVB-C(MPEG2 and MPEG4 AAC) cable-TV service. Please check with your local dealer the possibility to receive DVB-T or DVB-C signal.

2. DVB-T is the DVB European consortium standard for the broadcast transmission of digital terrestrial television and DVB-C is that for the broadcast transmission of digital TV over cable.

However, some differentiated features like EPG (Electric Program Guide), VOD (Video on Demand) and so on, are not included in this specification. So, they cannot be supported at this moment.

3. Although this TV set meets the latest DVB-T and DVB-C standards[August,2008], the compatibility with future DVB-T digital terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.

4. Some cable-TV providers may charge an additional fee for such a service and you may be required to agree to terms and conditions of their business.

5. Some Digital TV functions might be unavailable in some countries or regions and DVB-C might not work correctly with all providers.

6. For more information, please contact your local Samsung customer care centre.

© 2009 Samsung Electronics Co., Ltd. All rights reserved.

English - 2

BN68-02013A_Eng.indd 2 2009-09-18 �� 9:25:34

Contents

Connecting and Preparing Your TV

Checking Parts ..........................................................................4

Using the Stand-Base ...............................................................4

How to assemble the Stand-Base (depending on the model) ...4

Viewing the Control Panel .........................................................5

Viewing the Connection Panel ...................................................6

Remote Control .........................................................................7

Installing Batteries in the Remote Control .................................8

Switching On and Off .................................................................8

Placing Your Television in Standby Mode ..................................8

Viewing the Menus ....................................................................9

Using the TOOLS Button ...........................................................9

Plug & Play Feature ................................................................10

Channel Control

Storing Channels ................................................................... 11

Managing Channels ................................................................13

Picture Control

Changing the Picture Settings .................................................15

Using the 3D Function .............................................................18

Setting up the TV with your PC ...............................................19

PC Display ...............................................................................20

Sound Control

Changing the Sound Setting ...................................................21

Selecting the Sound Mode ......................................................22

Function Description

Configuring the Setup Menu ....................................................23

Setting the Time ......................................................................25

Source List / Edit Name ...........................................................26

Supported Program .................................................................27

About Anynet+

Connecting Anynet+ Devices

Setting Up Anynet+

..................................................28

.................................................................29

Scanning and Switching between Anynet+ Devices ................29

Recording ................................................................................30

Listening through a Receiver (Home theater)

Troubleshooting for Anynet

.........................31

+ ..................................................31

Recommendations for Use

Teletext Feature .......................................................................32

Wall Mount Kit Specifications (VESA) .....................................33

Preparing before installing Wall- Mount on the wall ................34

Securing the TV to the Wall .....................................................34

Securing the Installation Space ...............................................35

Troubleshooting .......................................................................36

Specifications ..........................................................................37

BN68-02013A_Eng.indd 3

Symbol Press

N

Note

O

One-Touch Button

T

TOOLS

English - 3

2009-09-18 �� 9:25:34

Connecting and Preparing Your TV

Checking Parts

Owner’s Instructions Remote Control/

AAA Batteries (2ea)

Power Cord Cloth-Clean Warranty Card/

Safety Guide Manual

(Not available in all locations)

Screw (4ea) Cover-Bottom Holder-Ring (4ea)

(Refer to page 34)

Ferrite Core for Power

Cord (1ea)

N

The ferrite core is used to shield the cable from interference.

When connecting a cable, open the ferrite core and clip it around the cable near the plug as shown in the figure.

Using the Stand-Base

N

N

Two or more people should carry the PDP. Never lay the PDP on the floor because of possible damage to the screen. Always keep the PDP upright.

The PDP can rotate 20 degrees in right and left directions.

-20° ~ 20°

How to assemble the Stand-Base

(depending on the model)

Using the 4 screws for securing the stand base and the monitor, firmly attach the monitor to the stand base.

(The exterior of the set may be different than the picture.)

In case of installing your TV on the wall, close the cover (1) on the stand-base connection part using two screws for hiding.

Warning

Firmly secure the stand to the TV before moving it, as the stand may fall and could cause serious injury.

N

Two or more people should carry the TV.

Never lay the TV on the floor because of possible damage to the screen.

Always store the TV upright.

English - 4

BN68-02013A_Eng.indd 4 2009-09-18 �� 9:25:37

Viewing the Control Panel

N

The product colour and shape may vary depending on the model.

Front Panel buttons

Touch each button to operate.

1 SOURCE

Toggles between all the available input sources

( TV, AV, Component 1, Component 2, PC, HDMI1,

HDMI2/DVI, HDMI3).

N

In the on-screen menu, use this button as you would use the ENTERE button on the remote control.

2

MENU

Press to see an on-screen menu of your TV’s features.

3 + VOL –

Press to increase or decrease the volume. In the on-screen menu, use the + VOL – buttons as you would use the

◄ and ► buttons on the remote control.

4 < CH >

Press to change channels. In the on-screen menu, use the

< CH > buttons as you would use the ▲ and ▼ buttons on the remote control.

5 POWER INDICATOR

Lights up when the power is on.

6

( POWER)

Press to turn the TV on and off.

7

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

8 SPEAKERS

BN68-02013A_Eng.indd 5

English - 5

2009-09-18 �� 9:25:38

Viewing the Connection Panel

TV Rear Panel

1

TV Side Panel

or

9

Cable Television

Network

2 or

3 4 5 1 6 7 8 0

N

The product colour and shape may vary depending on the model.

N

N

Whenever you connect an audio or video system to your set, ensure that all elements are switched off.

When connecting an external device, match the colour of the connection terminal to the cable.

1 SERVICE 1,2

Connector for service.

2 POWER IN

Connect the supplied power cord.

3 PC IN(PC) / (AUDIO)

Connect to the video and audio output jack on your PC.

4 COMPONENT IN 1, 2

Audio (AUDIO L/R) and video (Y/P

B

/P

R

) inputs for Component.

5 DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio Component.

6 3D SYNC OUT

Connect to 3D IR Emitter

7 AUDIO OUT(AUDIO R/L)

Connect RCA audio signals from the TV to an external source, such as Audio equipment.

8 HDMI IN 1, 2(DVI), 3

-

-

N

No additional Audio connection is needed for an HDMI to

HDMI connection.

When using an HDMI/DVI cable connection, you must use the HDMI IN 2 (DVI) jack.

What is HDMI?

High Definition Multimedia interface

-

allows the transmission of high definition digital video data and multiple channels of digital audio.

The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable (not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP

(High Bandwidth Digital Copy Protection) coding feature installed, and supports multi - channel digital audio.

DVI IN / AUDIO IN

DVI audio outputs for external devices.

9 ANT IN

75Ω Coaxial connector for Aerial/Cable Network.

0 AV IN (VIDEO / AUDIO R/L)

Video and audio inputs for external devices, such as a camcorder or VCR.

Supported modes for HDMI/DVI and Component

HDMI/DVI 50Hz

HDMI/DVI 60Hz

Component

480i 480p 576i 576p 720p 1080i 1080p

X

X

O

X

O

O

X

X

O

O

X

O

O

O

O

O

O

O

O

O

O

English - 6

BN68-02013A_Eng.indd 6 2009-09-18 �� 9:25:40

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

N

The performance of the remote control may be affected by bright light.

1 POWER button

(turns the TV on and off)

2

Selects the TV mode directly.

3 Number buttons for direct channel access

4

Use to Select on-screen menu items

5 Temporary sound switch-off

6 Volume increase

Volume decrease

7

Available source selection

8 Channel control button

9 Use to quickly select frequently used functions.

0 Control the cursor in the menu

!

Use to see information on the current broadcast

@ Use these buttons in the Channel list, etc.

$

Sound mode selection

% Use these buttons in the Channel list, and Anynet+.

^

Previous channel

& Next channel

Previous channel

*

Displays the main on-screen menu

( Press to switch to your favorite channels.

)

Returns to the previous menu a Exit the on-screen menu b Selects SRS TruSurround HD mode.

c Picture size selection d

Digital subtitle display e Electronic Program Guide (EPG) display

Teletext Functions

2 Exit from the teletext display

(depending on the model)

7

Teletext mode selection (LIST/FLOF)

8 Teletext store

9 Teletext size

!

Teletext reveal

@

Fastext topic selection

# Teletext display/mix both

teletext information and the normal broadcast

^ Teletext sub page

& P :Teletext next page

P :Teletext previous page

* Teletext index

) Teletext hold a

Teletext cancel

BN68-02013A_Eng.indd 7

English - 7

2009-09-18 �� 9:25:41

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the figure.

2. Install two AAA size batteries.

N

Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside the compartment.

3. Close the cover.

N

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.

N

If the remote control doesn’t work, check the following

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Switching On and Off

The mains lead is attached to the rear of your set.

1. Plug the mains lead into an appropriate socket.

N

The standby indicator lights up on your set.

2. Press the POWERP button on your set.

N

Yo u also can press the POWERP button or the TV button on the remote control to turn the TV on.

The programme that you were watching last is reselected automatically.

3. Press the numeric button (0~9) or channel up / down (< / >) button on the remote control or < CH > button on your set.

N

When you switch the set on for the very first time, you will be asked to choose language in which the menus are to be displayed.

4. To switch your set off, press the POWERP button again.

Placing Your Television in Standby Mode

Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1. Press the POWERP button on the remote control.

N

T he screen is turned off and a red standby indicator appears on your set.

2. To switch your set back on, simply press the POWERP, numeric buttons (0~9), TV button or channel up / down (< / >) button again.

N

Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug the set from the mains and aerial.

English - 8

BN68-02013A_Eng.indd 8 2009-09-18 �� 9:25:41

Viewing the Menus

1. With the power on, press the MENU button. The main menu appears on the screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input,

Application, Support.

2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTERE button to access the icon’s sub-menu.

3. Press the EXIT button to exit.

N

The on-screen menus disappear from the screen after about one minute.

Mode

Cell Light

Contrast

Brightness

Sharpness

Colour

Tint (G/R)

: Standard

: 4

: 95

: 45

: 50

: 50

: G50/R50

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on which external input mode you are viewing.

1. Press the TOOLS button. The Tools menu will appear.

2. Press the ▲ or ▼ button to select a menu, then press the ENTERE button.

3. Press the ▲ / ▼ / ◄ / ► / ENTERE buttons to display, change, or use the selected items. For a more detailed description of each function, refer to the corresponding page.

Tools

Anynet + (HDMI-CEC), see page 28

Picture Mode, see page 15

Sound Mode, see page 21

Sleep Timer, see page 25

Energy Saving, see page 24

Add to Favourite (or Delete from Favourite), see page 13

Auto Adjus tment, see page 19

Anynet+ (HDMI-CEC)

Picture Mode : Standard

Sound Mode

Sleep Timer

:

:

Custom

Off

Energy Saving

Add to Favourite

: Off

U Move E Enter e Exit

BN68-02013A_Eng.indd 9

English - 9

2009-09-18 �� 9:25:42

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

N

N

The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running.

The Screen Saver is activated if there is no operating signal for longer than 15 minutes.

1. Press the POWER button on the remote control. The message Select 'Home Use'

when installing this TV in your home. is displayed.

Plug & Play

2. Press the ◄ or ► button to select Store Demo or Home Use, then the ENTERE button.

N

N

N

Select 'Home Use' when installing this TV in your home.

We recommend setting the TV to Home Use mode for the best picture in your home environment.

Store Demo mode is only intended for use in retail environments.

If the unit is accidentally set to

Store Demo Home Use

◄► Move E Enter

Store Demo mode and you want to return to Home Use (Standard): Press the Volume button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

N

The factory default setting for the picture will be Standard. Standard mode is the recommended home viewing picture mode.

3. Select country. menu is displayed. Press the ENTEREbutton. Select the appropriate country by pressing the ▲ or ▼ button.

Press the ENTERE button to confirm your choice.

4. Press the ▲ or ▼ button to select the Antenna source to memorize. Press the ENTERE button to select Start.

Digital & Analogue : Digital and Analogue channels.

Digital : Digital channels.

Analogue : Analogue channels.

The channel search will start and end automatically.

N

N

N

Pr ess the ENTERE button at any time to interrupt the memorization process.

A fter all the available channels are stored, the message Set the Clock Mode. is displayed.

5. Press the ENTERE button. Press the ▲ or ▼ button to select Auto, then Press the ENTERE button.

N

N

If you select Manual, Set current date and time is displayed. (refer to page 25)

If you have received a digital signal, the time will be set automatically. If not, see page 25 to set the clock.

6. Press the ▲ or ▼ button to highlight the time zone for your local area (and to move the highlight to the appropriate time zone on the map of the Australia). Press the ENTERE button.

7. The brief instruction on How to get the best performance from your new HDTV is displayed. Press the ENTERE button.

N Th is menu is available HD Connection Guide in the Support menu.

8. The message Enjoy your TV. is displayed. When you have finished, press the ENTERE button.

If you want to return to this feature...

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTERE button.

2. Press the ENTERE button again to select Plug & Play.

3. Enter your 4 digit PIN number. The default PIN number of a new TV set is

‘0-0-0-0’.

N

If you want to change PIN number, refer to 23 page.

N

N

The Plug & Play feature is only available in the TV mode.

Any previous settings and adjustments will remain including the picture mode.

All Channel settings will be lost.

For home viewing, ensure the picture mode is set to Standard.

Plug & Play

Time

Game Mode

Child Lock

Change PIN

Parental Lock

Subtitle

: Off

: On

English - 10

BN68-02013A_Eng.indd 10 2009-09-18 �� 9:25:42

Channel Control

Storing Channels

Country

You can change the desired country.

N

N

The PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’.

N

N

N

N

N

Auto Store

Scans for all channels with active broadcast stations (and availability depends on your country) and stores them in the TV's memory.

You can memorize the Antenna source.

Digital & Analogue : Digital and Analogue channels.

Digital : Digital channels.

Analogue : Analogue channels.

If you want to stop Auto Store, press the ENTERE button.

The Stop Auto Store? message will be displayed.

Select Yes by pressing the ◄ or ► button, then press the ENTERE button.

If a channel is locked using the Child Lock function, the PIN input window appears.

The default PIN number of a new TV set is ‘0-0-0-0’.

Country

Auto Store

Manual Store

Full Guide

Mini Guide

Default Guide

Channel List

: Australia

: Full Guide

Manual Store

Scans for a channel manually and stores it in the TV’s memory.

N

N

If a channel is locked using the Child Lock function, the PIN input window appears.

The default PIN number of a new TV set is ‘0-0-0-0’.

„

N

N

Digital Channel

Manual store for digital channels.

Digital Channel is only availe in DTV mode.

Channel : Set the Channel number using the ▲, ▼ or number ( 0~9) buttons.

Frequency

Bandwidth

: Set the frequency using the number buttons.

: Set the bandwidth using the ▲, ▼ or number ( 0~9) buttons.

When it has finished, channels are updated in the channel list.

„

Analogue Channel (only analogue channel)

Manual store for analogue channel.

• Programme buttons.

(Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number (0~9)

Colour System → Auto / PAL / SECAM / NTSC4.43

Sound System

: Sets the colour system value using the ▲ or ▼ button.

BG / DK / I / L : Sets the sound system value using the ▲ or ▼ button.

Channel (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or

S (Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.

N

N

You can also select the channel number directly by pressing the number ( 0~9) buttons.

If there is abnormal sound or no sound, reselect the sound standard required.

N

Search (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the frequency range until the first channel or the channel that you selected is received on the screen.

Store (When you store the channel and associated programme number): Set to OK by pressing the ENTERE button.

Channel mode

- (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in this mode.

BN68-02013A_Eng.indd 11

English - 11

Continued...

2009-09-18 �� 9:25:42

„

„

Full Guide / Mini Guide

The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new information becomes available.

O

You can also display the guide menu simply by pressing the GUIDE button.

Full Guide : Displays the programme information as time ordered One hour segments. One hours of programme information is displayed which may be scrolled forwards or backwards in time.

Mini Guide : The information of each programme is displayed by each line on the current channel Mini Guide screen from the current programme onwards according to the programme starting time order.

„

Default Guide

Mini Guide / Full Guide : You can decide whether to display either the Mini Guide or the Full Guide when the GUIDE button on the remote control is pressed.

Full Guide

Mini Guide

Default Guide

Channel List

Channel Mode

Fine Tune

: Full Guide

: Added Ch.

Using the Full / Mini Guide

Full Guide

DTV Cable 900 f tn 2:10 Tue 1 Jun

Freshmen On Campus

2:00 - 2:30

No Detailed Information

Today

900 f tn

901 ITV Play

902 Kerrang!

903 Kiss

903 oneword

903 Smash Hits!

Watch

2:00 - 3:00

Freshmen O..

Mint Extra

Loaded

Street Hypn..

Fresh 40 with Dynamite MC

The Distillery

Smash Hits! Sunday

Information ◀◀ ▶▶ Page

No Information

No Information

Kisstory

No Information

„ Mini Guide „

3:00 - 4:00

+24 Hours „ Exit

Mini Guide

2:00

2:30

5:00

DTV Cable 900 f tn

Freshmen On Campus

Street Hypnosis

Booze Britain

Watch Information ◀◀ ▶▶ Page „ Full Guide „ Exit

▲ / ▼ / ◄ / ►,

( ENTER)

RED

GREEN

YELLOW

BLUE

INFO

Select a programme by pressing the ▲/▼/◄/► button.

If the next progrmme is selected, it is scheduled with the clock icon displayed. If the ENTERE button is pressed again, press the ▲/▼/◄/► button to select Cancel Schedules, the scheduling is canceled with the clock icon gone.

For details about scheduling programmes, refer to the section.

Toggle between the Mini Guide or Full Guide.

Full Guide: Scroll backwards quickly (-24 hours).

Mini Guide: Display previous page quickly.

Full Guide: Scroll forwards quickly (+24 hours).

Mini Guide: Display next page quickly.

Exit the guide.

INFO button for the detailed information. Channel Number, Running Time, Status Bar, Parental Level, Video Quality

Information (HD/SD), Sound Modes, Subtitle or Teletext, languages of Subtitle or Teletext and brief summary of the highlighted programme are included on the detailed information. “…” will be appeared if the summary is long.

Channel List

For the detailed procedures on using the Channel List, refer to the descriptions on pages 13~14.

„

„

Channel Mode

When the P (< / >) button is pressed, Channels will be switched within the selected channel list.

Added Ch.

: Channels will be switched within the memorized channel list.

Favourite Ch.

: Channels will be switched within the favourite channel list.

Fine Tune (only analogue channels)

If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually.

N

N

N

Fine tuned channels that have been saved are marked with an asterisk * on the right-hand side of the channel number in the channel banner.

If you do not store the fine-tuned channel in memory, adjustments are not saved.

To reset the fine-tuning, select Reset by pressing the ▼ button and then press the ENTERE button.

English - 12

BN68-02013A_Eng.indd 12 2009-09-18 �� 9:25:43

Managing Channels

Using this menu, you can Add / Delete or set Favourite channels and use the programme guide for digital broadcasts.

N

Select a channel in the All Channels, Added Channels, Favourites, or Programmed screen by pressing the ▲ / ▼ buttons, and pressing the ENTERE button. Then you can watch the selected channel.

N

N

Mini Guide

Default Guide

Channel List

Channel Mode

: Full Guide

: Added Ch.

All Channels : Shows all currently available channels.

Added Channels : Shows all added channels.

Favourites : Shows all favourite channels.

Programmed : Shows all current reserved programmes.

Using the Colour buttons with the Channel List

-

-

-

-

Red (

T

Channel Type

Green (

Yellow (

Zoom

): Toggle between your TV, Radio, Data / Other and All.

): Enlarges or shrinks a channel number.

Select ): Selects multiple channel lists.

TOOLS (Tools): Displays the Delete (or Add), Add to Favourite (or Delete from

Favourite), Timer Viewing, Edit Channel Name, Edit Channel Number, Sort,

Lock (or Unlock), Select All, Deselect All, or Auto Store menu.

(The Options menus may differ depending on the situation.)

Channel Status Display Icons

A An Analogue channel.

A channel set as a Favourite.

\ A locked channel.

All

Fine Tune

20

21

ABC HDTV

ABC2

A

0 C --

A

1 C --

A

2 ♥ C --

A

3 C --

A

4 C --

A

5 C --

A

6 C --

A

7 C --

„ Channel Type „ Zoom „ Select c A channel selected by pressing the yellow button.

( A programme currently being broadcast.

) A reserved programme

Tools

Channel List Tools Menu (in All Channels / Added Channels / Favourites)

N

N

Press the TOOLS button to use the tools menu.

Option menu items may differ depending on the channel status.

„

N

N

N

N

Add / Delete

You can delete or add a channel to display the channels you want.

All deleted channels will be shown on All Channels menu.

A gray-coloured channel indicates the channel has been deleted.

The Add menu only appears for deleted channels.

You can also delete a channel to the same manner.

Added Channels or Favourite menu in the

„

Add to Favourite / Delete from Favourite

You can set channels you watch frequently as favourites.

All

20

21

ABC HDTV

ABC2

A

0 C --

A

1 C --

A

2 C --

A

3 C --

A

4 C --

A

5 C --

A

6 C --

A

7 C --

Delete

Add to Favourite

Timer Viewing

Edit Channel Name

Sort

Lock

„ Channel Type „ Zoom „ Select

Tools

„

T

Press the TOOLS button to display Tools menu.

You can also add the favourite channel by selecting ToolsAdd to Favourite (or Delete from Favourite).

N

N

The “♥” symbol will be displayed and the channel will be set as a favourite.

All favourite channels will be shown on Favourite menu.

Timer Viewing

If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel List; even when you are watching another channel. To reserve a programme set the current time first. (See page 25)

N

N

N

Only memorized channels can be reserved.

You can set the channel, month, day, year, hour and minute directly by pressing the number buttons on the remote control.

Reserving a programme will be shown on Programmed menu.

N Digital Programme Guide and Viewing Reservation

When a digital channel is selected, and you press the ► button, the Programme Guide for the channel appears.

You can reserve a programme according to the procedures described above.

BN68-02013A_Eng.indd 13

English - 13

Continued...

2009-09-18 �� 9:25:44

„

Edit Channel Name (only analogue channel)

Channels can labeled so that their call letters appear whenever the channel is selected.

N The names of digital broadcasting channels are automatically assigned and cannot be labeled.

„

Edit Channel Number (only digital channel)

You can also edit the channel number by pressing the number buttons on the remote control.

„

Sort (only analogue channel)

This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using the auto store.

„

Lock / Unlock

You can lock a channel so that the channel cannot be selected and viewed. This function is available only when the Child Lock is set to On. (see page 23)

N The PIN number input screen appears. Enter your 4 digit PIN number.

N

N

The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN, by selecting

The “ \” symbol will be displayed and the channel will be locked.

Change PIN from the menu.

„

Select All / Deselect All

N

N

N

Select All : You can select all the channels in the channel list.

Deselect Al l: You can deselect all the selected channels in the channel list.

You can perform the add / delete, add to Favourites / delete from Favourites, or lock / unlock function for multiple channels at the same time. Select the required channels and press the yellow button to set all the selected channels at the same time.

The c mark appears to the left of the selected channels.

You can only select Deselect All when there is a selected channel.

1 / 1 / 2009

„

Auto Store

N

For further details on setting up options, refer to page 11.

N

If a channel is locked using the Child Lock function, the PIN input window appears.

13:59 5 TV1 Quincy, M.E

18:59 2

20:59 2

21:59 2

TV3 The Equalizer

TV3 McMillan & Wife

TV3 M.Spillane’s mike Hammer

Channel List Tools Menu (in Programmed)

You can view, modify or delete a reservation.

N

Press the TOOLS button to use the tools menu.

„ Zoom „ Select Tools Information

„

Change Info

Select to change a viewing reservation.

„

Cancel Schedules

Select to cancel a viewing reservation.

„

Information

Select to view a viewing reservation. (You can also change the reservation information.)

„

Select All / Deselect All

You can select (or deselect) all channels in the channel list.

BN68-02013A_Eng.indd 14

English - 14

2009-09-18 �� 9:25:44

Picture Control

Changing the Picture Settings

Mode

You can select the type of picture which best corresponds to your viewing requirements.

Dynamic : Selects the picture for high-definition in a bright room.

Standard : Selects the picture for the optimum display in a normal environment.

Movie : Selects the picture for viewing movies in a dark room.

T

Press the TOOLS button to display Tools menu.

You can also set the picture mode by selecting Tools → Picture Mode.

Mode

Cell Light

Contrast

Brightness

Sharpness

Colour

: Standard

: 4

: 95

: 45

: 50

: 50

N

N

N

N

N

N

Cell Light / Contrast / Brightness / Sharpness / Colour / Tint (G/R)

Your television has several setting options that allow you to control the picture quality.

Tint (G/R) : G50/R50

Cell Light : Adjusts the pixel brightness.

Contrast : Adjusts the contrast level of the picture.

Brightness : Adjusts the brightness level of the picture.

Sharpness : Adjusts the edge definition of the picture.

Colour : Adjusts Colour saturation of the picture.

Tint (G/R) : Adjusts the Colour tint of the picture.

Select a picture mode to be adjusted first. The adjusted values are saved for each picture mode.

When you make changes to Cell Light, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted accordingly.

In Analogue TV, AV modes of the PAL system, you cannot use the Tint Function.

In PC mode, you can only make changes to Cell Light, Contrast and Brightness.

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and then this will reduce the overall running cost.

Advanced Setting

You can adjust the detailed settings for your screen including the color and contrast.

N

N

Advanced Setting is available in Standard or Movie mode.

In PC mode, you can only make changes to Gamma and White Balance from among the Advanced Setting items.

„

Black Tone → Off / Dark / Darker/ Darkest

You can select the black level on the screen to adjust the screen depth.

Colour

Tint (G/R)

Advanced Setting

: 50

: G50/R50

Picture Options

Picture Reset

„

Dynamic Contrast → Off / Low / Medium / High

You can adjust the screen contrast so that the optimal contrast is provided.

„

Gamma

You can adjust the primary colour Intensity.

„

Colour Space

Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite colour space to experience the most natural colour.

• Auto :

Native

Automatically sets the color range depending on the input video source.

Sets the color range wider than the that of the input video source.

„

White Balance

You can adjust the colour temperature for more natural picture colours.

• R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain

Reset

: Changing the adjustment value will refresh the adjusted screen.

: The previously adjusted white balance will be reset to the factory defaults.

„

Flesh Tone

You can adjust the flesh tone to be more or less red.

N

Changing the adjustment value will refresh the adjusted screen.

„

Edge Enhancement → Off / On

You can emphasize object boundaries in the picture.

Continued...

English - 15

BN68-02013A_Eng.indd 15 2009-09-18 �� 9:25:44

Picture Options

You can customize the additional picture settings to suit your preference.

N

In PC mode, you can only make changes to the Colour Tone, Size and Screen

Burn Protection from among the items in Picture Options.

Tint (G/R)

Advanced Setting

Picture Options

Picture Reset

: G50/R50

„

Colour Tone → Cool / Normal / Warm1 / Warm2

You can select the most comfortable colour tone to your eyes.

N

N

The adjusted values are stored according to the selected Picture mode.

Warm1 or Warm2 is only activated when the picture mode is Movie.

„

Size

You can select the picture size which best corresponds to your viewing requirements.

16:9

4:3

: Sets the picture to the 16:9 aspect ratio.

Wide Zoom

Zoom

: Magnify the size of the picture more than 4:3.

: Magnifies the 16:9 wide picture (in the vertical direction) to fit the screen size.

: Sets the picture to the 4:3 aspect ration.

Screen Fit : Use the function to see the full image without any cutoff when HDMI (720p/1080i/1080p) or Component

(1080i/1080p) signals are input.

N

The picture size options may vary depending on the input source.

N

N

N

The items available may differ depending on the selected mode.

In PC Mode, only 16:9 and 4:3 mode can be adjusted.

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

O

N

N

N

N

N

N

Temporary image retention may occur when viewing a static image on the set for more than two hours.

Wide Zoom : Press the ► button to select Position, then press the ENTERE button.

Press the ▲ or ▼ button to move the screen up / down. Then press the ENTERE button.

Zoom : Press the ► button to select Position, then press the ENTERE button. Press the ▲ or ▼ button to move the picture up and down. Then press the ENTERE button. Press the ► button to select Size, then press the ENTERE button.

Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the ENTERE button.

After selecting Screen Fit in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.

Reset : Press the ◄ or ► button to select

If you use the

Reset, then press the ENTERE

Screen Fit function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the overscan function.

You can select these options simply by pressing the control.

button. You can initialize the setting.

P.SIZE button on the remote

„

Digital NR → Off / Low / Medium / High / Auto

If the broadcast signal received by your TV is weak, you can activate the Digital Noise

Reduction feature to help reduce any static and ghosting that may appear on the screen.

N

When the signal is weak, select one of the other options until the best picture is displayed.

„

HDMI Black Level → Normal / Low

You can directly select the black level on the screen to adjust the screen depth.

N

This function is active only when the external input connects to HDMI (RGB signals).

BN68-02013A_Eng.indd 16

English - 16

Continued...

2009-09-18 �� 9:25:44

„

Film Mode

You can optimize the picture mode for watching movies.

N

• Off : Turn the film mode function off.

Auto : Automatically adjusts the picture for the best quality when watching a film.

N

Film Mode is supported in TV, AV, COMPONENT(480i/1080i) and HDMI(480i/1080i).

Film Mode is not supported in DTV channel with resolution 576p/720p.

„

Screen Burn Protection

Configures the Screen Burn Protection Options to prevent and reduce pixel burn.

When an image remains in one position too long, it may cause a permanent burn on the screen.

• Pixel Shift : To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down (Vertical) and side to side (Horizontal). The Time setting allows you to program the time between movement of the picture in minutes.

N

N

N

N

Set Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTEREbutton.

Select the required option by pressing the ▲ or ▼ button, then press the ENTERE button.

Available options: Horizontal, Vertical, Time.

Optimum condition for pixel shift

Horizontal

Vertical

Time (minute)

Item

0~4

0~4

1~4 min

TV/AV/Component/HDMI/PC

2

2

3 min

N

N

The Pixel Shift value may differ depending on the monitor size (inches) and mode.

This function is not available in the Screen Fit mode.

-

-

Scrolling : This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern

Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time.

Side Gray : When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white balance on both extreme left and right sides.

Dark

Light

: When you set the screen ratio to 4:3, it darkens the left and right sides.

: When you set the screen ratio to 4:3, it brightens the left and right sides.

BN68-02013A_Eng.indd 17

English - 17

2009-09-18 �� 9:25:45

Using the 3D Function

You can enjoy 3D movies and games on your TV. The 3D effects function enables you to view 3D images using special 3D glasses.

Connections

3D Glasses

(Not supplied)

3D IR Emitter

(Not supplied)

TV Rear Panel

2

PC

3.5mm Stereo Audio Cable (Not supplied)

1

HDMI/DVI Cable (Not supplied)

N

The appearance of the 3D glasses (including Emitter) may differ depending on the model of your glasses.

N

N

N

N

N

N

N

1. Connect a HDMI/DVI cable between the HDMI IN 2(DVI) jack on the TV and the PC output jack on your computer.

2. Connect a 3.5mm Stereo Audio Cable between the DVI AUDIO IN jack on the TV and the Audio Out jack of the sound card on your computer.

3. Connect the Emitter to the 3D SYNC OUT port on the rear panel of the TV.

4. Turn the TV on and set the source of the TV to HDMI2/DVI.

N

N

N

N

For more information on the 3D glasses (including the Emitter), refer to the user manual of your 3D glasses.

Adjust the PC resolution : - PS42B450: 1024 x 768@60Hz

- PS50B450: 1024 x 768@60Hz, 1360 x 768@60Hz

Optimum PC resolution for PS50B450 is 1360x768. When 1024x768 signal is connected in 3D mode, the picture will be shown in

4:3 format with left and right side grey bars appeared.

The 3D IR Emitter communicates with the 3D glasses.

Therefore, the 3D IR Emitter should be located near the 3D glasses.

It is activated when the HDMI or DVI input signal is RGB, and DVI Sound is supported.

When the power is turned on or off, the mode changes to the default ( Off) and the Format is saved.

To use the 3D Effect function, a graphics card supporting 3D or 3D software is required.

The 3D glasses and the Emitter must be manufacturer by the same company.

If you play a game or watch TV while wearing the 3D glasses for long periods of time, you may experience eyestrain or a headache.

3D glasses (including the Emitter) not manufactured by Samsung may not be supported.

If you fi nd the screen fl ickering while the 3D function is used, change the environmental lighting darker or turn off the fl uorescent lamp to watch the screen for its best condition.

BN68-02013A_Eng.indd 18

English - 18

Continued...

2009-09-18 �� 9:25:46

Changing the Mode

Provides the function to turn on the 3D Effect. You can choose between Mode1 and

Mode2. To achieve the 3D effect, the 3D glasses shutter back and forth from the left to right and vice versa (left/right sync).

Off

2D

: Turns the 3D effect function off.

Mode1

Mode2

: Mode 1 operates with right sync first.

: Mode 2 operates with left sync first.

: Provides picture converted 3D to 2D. You can choose this to watch 2D picture temporally when you feel dizzy, but you should choose Off to end 3D Effect completely.

N

N

You should choose Off to end 3D effect completely.

If the 3D effect is not working properly, it means the Mode and 3D glasses may not be syncing properly. To put them in sync, switch to the other mode.

Size

Screen Mode

Digital NR

HDMI Black Level

Film Mode

Picture Options

: Auto Wide

: 16:9

: Auto

Screen Burn Protection

: Normal

: Off

3D Effect

Move Enter

Mode

Format

3D Effect

: Off

: Checker Board

Return

Return

Move Enter

Changing the Format

Select the optimal input format to match your graphic cards or 3D software.

Checker Board : If the output format of your graphic card or 3D software is Checker Board, select this input format.

Horizontal : If the output format of your graphic card or 3D software is Horizontal interleaved, select this input format.

Vertical : If the output format of your graphic card or 3D software is Vertical interleaved, select this input format.

Picture Reset → Reset Picture Mode / Cancel

Resets all picture settings to the default values.

N

Select a picture mode to be reset. The reset is performed for each picture mode.

Advanced Setting

Picture Options

Picture Reset

Setting up the TV with your PC

N

Preset: Press the SOURCE button to select PC mode.

Auto Adjustment

Auto Adjustment allows the PC screen of set to self-adjust to the incoming PC video signal. The values of fine, coarse and position are adjusted automatically.

N

This function does not work in DVI-HDMI mode.

T

Press the TOOLS button to display Tools menu.

You can also set the adjustment by selecting Tools → Auto Adjustment.

Brightness

Sharpness

Auto Adjustment

: 50

: 50

Screen

Advanced Setting

Picture Options

Picture Reset

„

„

„

„

Screen

Coarse

Adjusts the frequency when vertical noise appears on the screen.

Fine

Adjusts the screen to be clearer.

PC Position

Adjust the PC’s screen positioning if it does not fit the TV screen. Press the ▲ or ▼ button to adjusting the Vertical-Position. Press the ◄ or ► button to adjust the Horizontal-Position.

Image Reset

You can replace all image settings with the factory default values.

English - 19

BN68-02013A_Eng.indd 19 2009-09-18 �� 9:25:46

PC Display

Setting Up Your PC Software (Based on Windows XP)

The Windows display-settings for a typical computer are shown below. The actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. However, even if your actual screens look different, the same basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)

1. First, click on ‘Control Panel’ on the Windows start menu.

2. When the control panel window appears, click on ‘Appearance and Themes’ and a display dialog-box will appear.

3. When the control panel window appears, click on ‘Display’ and a display dialog-box will appear.

4. Navigate to the ‘Settings’ tab on the display dialog-box.

The correct size setting (resolution)

Optimum: PS42B450: 1024x768 pixels , PS50B450: 1360x768 pixels

If a vertical-frequency option exists on your display settings dialog box, the correct value is ‘60’ or ‘60 Hz’. Otherwise, just click ‘OK’ and exit the dialog box.

Display Modes

Both screen position and size will vary depending on the type of PC monitor and its resolution.

The resolutions in the table are recommended.

„

D-Sub and HDMI/DVI Input

Mode

IBM

MAC

VESA DMT

VESA CVT

VESA GTF

Resolution

640 x 350

720 x 400

640 x 480

832 x 624

640 x 480

800 x 600

1024 x 768

1360 x 768

720 x 576

1280 x 720

1280 x 720

Horizontal

Frequency (kHz)

31.469

31.469

35.000

49.726

31.469

37.861

37.500

37.879

48.077

46.875

48.363

56.476

60.023

47.712

35.910

56.456

44.772

52.500

Vertical

Frequency (Hz)

70.086

70.087

66.667

74.551

59.940

72.809

75.000

60.317

72.188

75.000

60.004

70.069

75.029

60.015

59.950

74.777

59.855

70.000

Pixel Clock

Frequency (MHz)

25.175

28.322

30.240

57.284

25.175

31.500

31.500

40.000

50.000

49.500

65.000

75.000

78.750

85.500

32.750

95.750

74.500

89.040

N

N

N

When using an HDMI / DVI cable connection, you must use the HDMI IN 2 (DVI) jack.

The interlace mode is not supported.

The set might operate abnormally if a non-standard video format is selected.

- / -

+ / +

+ / +

- / +

- / +

- / +

- / +

Sync Polarity

(H/V)

+ / -

- / +

- / -

- / -

- / -

- / -

- / -

+ / +

+ / +

+ / +

- / -

PS42B450

PS50B450

English - 20

BN68-02013A_Eng.indd 20 2009-09-18 �� 9:25:46

Sound Control

Changing the Sound Setting

Mode → Standard / Music / Movie / Clear Voice / Custom

You can select the type of special sound effect to be used when watching a given broadcast.

Mode : Custom

T

Press the TOOLS button to display Tools menu.

You can also configure the sound mode by selecting ToolsSound Mode.

Equalizer

SRS TruSurround HD : Off

Audio Language

Audio Format

Audio Description

Auto Volume

: ----

: ----

Equalizer

The sound settings can be adjusted to suit your personal preferences.

: Off

Mode : You can select a sound mode to suit your personal preferences.

Balance : Controls the balance between the right and left speakers.

100Hz / 300Hz / 1 KHz / 3KHz / 10KHz (Bandwidth Adjustment): To adjust the level of different bandwidth frequencies

Reset : Resets the equalizer settings to the default values.

SRS TruSurround HD → Off / On

SRS TruSurround HD is the combined technology of TruSurround and FOCUS, TruBass.

SRS TruSurround HD is down mixing technology that makes the Surround Sound effect of virtual 5.1 channel via two speakers.

This function provide not only rich deep bass at a low-pitched sound but also improve the resolution at a high-pitched sound.

TruSurround HD, SRS and the symbol are trademarks of SRS Labs, Inc.

TruSurround HD technology is incorporated under license from SRS Labs, Inc.

Audio Language (only digital channel)

You can change the default value for audio languages. Displays the language information for the incoming stream.

N

You can only select the language among the actual languages being broadcast.

Audio Format → MPEG / Dolby Digital (only digital channel)

When sound is emitted from both the main speaker and the audio receiver, a sound echo may occur due to the decoding speed difference between the main speaker and the audio receiver. In this case, use the TV Speaker function.

N

You can only select the language among the actual languages being broadcast.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Audio Description (only digital channel)

This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the

Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can turn the

Audio Description On or Off and control the volume.

„

Audio Description → Off / On

Turn the audio description function on or off.

„

Volume

You can adjust the audio description volume.

N Volume is active when Audio Description is set to On.

Auto Volume → Off / On

Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

Continued...

English - 21

BN68-02013A_Eng.indd 21 2009-09-18 �� 9:25:47

Speaker Select → External Speaker / TV Speaker

If you want to hear the sound through separate speakers, cancel the internal amplifier.

N

N

The

If you select

+, M MUTE buttons do not operate when the Speaker Select is set to External Speaker.

External Speaker in the Speaker Select menu, the sound settings will be limited.

TV Speaker

External Speaker

Video No Signal

TV's Internal Speakers

TV / AV / Component / PC / HDMI

Speaker Output

Mute

Mute

Audio Out (Optical, L / R Out) to Sound System

TV / AV / Component / PC / HDMI

Sound Output

Sound Output

Mute

Sound Reset → Reset All / Reset Sound Mode / Cancel

You can restore the Sound settings to the factory defaults.

Auto Volume

Speaker Select

Sound Reset

: Off

: TV Speaker

Selecting the Sound Mode

When you set to Dual l ll, the current sound mode is displayed on the screen.

Type of broadcast

Regular broadcast

(Standard audio)

Regular + NICAM Mono

NICAM

Stereo

NICAM-Stereo

NICAM

NICAM

Stereo

On-screen indication

Mono (Normal use)

NICAM Dual-I/II

NICAM

Dual-1

NICAM

Dual-2

Regular broadcast

(Standard audio)

Bilingual or DUAL-I/II

Stereo

Mono (Normal use)

A2

Stereo

Dual I

Stereo

N

N

N

O

If the stereo signal is weak and an automatic switching occurs, then switch to the mono.

This function is only activated in stereo sound signal. It is deactivated in mono sound signal.

This function is only available in Analog TV mode.

You can select these options simply by pressing the DUAL button on the remote control.

Mono

(Normal)

Mono

(Normal)

Mono

(Normal)

Dual II

Mono

(Forced mono)

English - 22

BN68-02013A_Eng.indd 22 2009-09-18 �� 9:25:47

Function Description

Configuring the Setup Menu

„

Game Mode

When connecting to a game console such as PlayStation TM or Xbox more realistic gaming experience by selecting the game menu.

TM , you can enjoy a

Plug & Play

Time

Game Mode

N

N

N

N

N

N

When the Game Mode is On

• Picture Mode mode.

Sound Mode

is automatically changed to Standard and users cannot change the

is automatically changed to Custom and users cannot change the mode. Adjust the sound using the equalizer.

The Reset in the Sound menu is activated. Reset function initializes the Equalizer settings to the factory default setting.

Child Lock

Change PIN

Parental Lock

Subtitle

Teletext Language

Preference

Game Mode is not available in regular TV mode or Game Mode set to Off.

If the picture is poor when external device is connected to TV, check if Game Mode is On.

This function supports only game function.

If you display the TV menu in Game mode, the screen shakes slightly.

The mark ( ) appears on the screen which means that Game Mode is on with the selected source.

Game mode is not available in PC mode.

: Off

: On

: - - - -

N

N

N

N

Child Lock → Off / On

This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by muting out video and audio.

Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN by selecting Change PIN from the menu.

You can lock some channels in Channel List. (refer to page 14)

Child Lock is available only in TV mode. .

N

N

N

Change PIN

You can change your personal ID number that is required to set up the TV.

Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’.

If you forget the PIN code, press the remote control buttons in the following sequence, which resets the PIN to

POWER (Off), MMUTE, 8, 2, 4, POWER (On).

‘0-0-0-0’:

N

N

N

N

Parental Lock

This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by a 4-digit PIN

(Personal Identification Number) code that is defined by the user.

Before the setup screen appears, the PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is

When the parental ratings are set, the “

‘0-0-0-0’. You can change the PIN by selecting Change PIN from the menu.

\ ” symbol is displayed.

Allow All : Press to unlock all TV ratings.

Block All: Press to lock all TV ratings.

N

Subtitle

You can activate and deactivate the subtitles. Use this menu to set the Subtitle Mode. Normal under the menu is the basic subtitle and Hard of hearing is the subtitle for a hearing-impaired person.

N

O

Subtitle → Off / On : Switches subtitles off or on.

Mode → Normal / Hard of hearing : Sets the subtitle mode.

Subtitle Language : Set the subtitle language.

If the programme you are watching does not support the Hard of hearing function, Normal automatically activates even though

Hard of hearing mode is selected.

English is the default in cases where the selected language is unavailable in the broadcast.

You can select these options simply by pressing the control.

SUBT. button on the remote

Continued...

English - 23

BN68-02013A_Eng.indd 23 2009-09-18 �� 9:25:47

Teletext Language

You can set the Teletext language by selecting the language type.

N

English is the default in cases where the selected language is unavailable in the broadcast.

„

Preference

Primary Audio Language / Secondary Audio Language / Primary Subtitle Language / Secondary Subtitle Language /

Primary Teletext Language / Secondary Teletext Language

Using this feature, users can select one of the languages. The language selected here is the default when the user selects a channel.

If you change the language setting, the Subtitle Language, Audio Language, and the Teletext Language of the Language menu are automatically changed to the selected language.

The Subtitle Language, Audio Language, and the Teletext Language of the Language menu show a list of languages supported by the current channel and the selection is highlighted. If you change this language setting, the new selection is only valid for the current channel. The changed setting does not change the setting of the Primary Subtitle Language, Primary Audio Language, or the Primary Teletext Language of the Preference menu.

Digital Text → Disable / Enable (Not available in all locations)

If the programme is broadcast with digital text, this feature is enabled.

N MHEG (Multimedia and Hypermedia Information Coding Experts Group)

An International standard for data encoding systems used in multimedia and hypermedia. This is at a higher level than the MPEG system which includes data-linking hypermedia such as still images, character service, animation, graphic and video files as well as multimedia data. MHEG is user runtime interaction technology and is being applied to various fields including VOD (Video-On-

Demand), ITV (Interactive TV), EC (Electronic Commerce), tele-education, tele-conferencing, digital libraries and network games.

Melody → Off / Low / Medium / High

The TV power on / off melody sound can be adjusted.

N

The Melody does not play

-

-

-

When no sound is output from the TV because the MMUTE button has been pressed.

When no sound is output from the TV because the

When the TV is turned off by Sleep Timer function.

– (Volume) button has been pressed.

Teletext Language : ----

Preference

Digital Text : Enable

Melody

Energy Saving

: Medium

: Off

Energy Saving

This feature adjusts the brightness of the TV in order to reduce power consumption. When watching TV at night, set the

Energy Saving mode option to High to reduce eye fatigue as well as power consumption.

• Off : Turns off the energy saving function.

Low : Sets the TV to low energy saving mode.

Medium

High

: Sets the TV to medium energy saving mode.

: Sets the TV to high energy saving mode.

T Press the TOOLS button to display Tools menu.

You can also set the Energy Saving option by selecting Tools → Energy Saving.

BN68-02013A_Eng.indd 24

English - 24

2009-09-18 �� 9:25:48

Setting the Time

Clock

Setting the clock is necessary in order to use the various timer features of the TV.

N

N

The current time will appear every time you press the INFO button.

If you disconnect the power cord, you have to set the clock again.

„

Clock Mode

You can set up the current time manually or automatically.

• Auto : Set the current time automatically using the time from the digital broadcast.

Manual : Set the current time to a manually specified time.

„

Clock Set

You can set the current time manually.

N

N

Set up this item when you have set Clock Mode to Manual.

You can set the day, month, year, hour or minute directly by pressing the number buttons on the remote control.

„ Time Zone

You can select your time zone.

N

The Antenna or cable must be connected in order to set the time automatically.

Sleep Timer → Off / 30 min / 60 min / 90 min / 120 min / 150 min /

180 min

The sleep timer automatically shuts off the TV after a preset time.

N

N

The TV automatically switches to standby mode when the timer reaches 0.

To cancel the Sleep Timer function, select Off.

T

Press the TOOLS button to display Tools menu.

You can also set the sleep timer by selecting Tools → Sleep Timer.

Clock Mode

Clock Set

Time Zone

Plug & Play

Time

Game Mode

Child Lock

Change PIN

Parental Lock

: Off

: On

Subtitle

Teletext Language : - - - -

Clock

: Auto

: New South Wales/ACT

U Move E Enter R Return

„

„

„

„

„

„

N

N

Timer 1 / Timer 2 / Timer 3

Three different on / off timer settings can be made.

On Time : Set the hour, minute, and Activate / Inactivate.

(To activate timer with the setting you’ve chosen, set to Activate.)

Off Time : Set the hour, minute, and Activate / Inactivate.

(To activate timer with the setting you’ve chosen, set to Activate.)

Volume : Set the required volume level.

Antenna: Select ATV or DTV.

Channel: Select the desired channel.

Repeat : Select Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun, or Manual.

N

N

When Manual is selected, press the ► button to select the desired day of the week. Press the ENTERE button over the desired day and the c mark will appear.

You must set the clock first.

You can set the hour, minute, and channel by pressing the number buttons on the remote control.

Auto Power Off

When you set the timer On, the television will eventually turn off, if no controls are operated for 3 hours after the TV was turned on by the timer. This function is only available in timer On mode and prevents overheating, which may occur if a TV is on for too long time.

English - 25

BN68-02013A_Eng.indd 25 2009-09-18 �� 9:25:48

Source List / Edit Name

„

Source List

Use to select TV or other external input sources such as DVD players or Cable Box /

Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of your choice.

TV , AV, Component1, Component2, PC, HDMI1, HDMI2/DVI, HDMI3.

N

N

N

O

You can choose only those external devices that are connected to the TV. In the

Source List, connected inputs will be highlighted and sorted to the top. Inputs that are not connected will be sorted to the bottom.

PC always stays activated.

Using the Colour buttons on the remote with the Source list

(Refresh): Refreshes the connecting external devices.

Red

T

Press the SOURCE button on the remote control to view an external signal source.

TV mode can be selected by pressing the TV button, number buttons (0~9), and the

P < / > button on the remote control.

Source List

Edit Name

„

Edit Name

VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game / Camcorder / PC / DVI PC / DVI / TV / IPTV /

Blu-ray / HD DVD / DMA

You can name the device connected to the input jacks to make your input source selection easier.

N

N

When a PC with a resolution of PS42B450: 640x480@60Hz, PS50B450: 640x480@60Hz, 1280x720@60Hz is connected to the

HDMI IN 2 (DVI) port, you should set the HDMI2/DVI mode to PC in the Edit Name of the Input mode.

When connecting an HDMI/DVI cable to the HDMI IN 2 (DVI) port, you should set the HDMI2/DVI mode to DVI or DVI PC in the

Edit Name of the Input mode. In this case, a separate sound connection is required.

BN68-02013A_Eng.indd 26

English - 26

2009-09-18 �� 9:25:48

Supported Program

„

Self Diagnosis

Picture Test

If you think you have a picture problem, perform the picture test. Check the color pattern on the screen to see if the problem still exists.

N

Does the problem still exist with this test photo?

appears on the screen.If the test pattern does not appear or there is noise in the test pattern, select Yes. If the test pattern is properly displayed, select No.

Yes

No

: There may be a problem with the TV. Contact Samsung’s Call Center for assistance.

: There may be a problem with your external equipment. Please check your connections. If the problem still persists, refer to the external device’s user manual.

„

Sound Test

If you think you have a sound problem, please perform the sound test.You can check the sound by playing a built-in melody sound through the TV.

N

• : There may be a problem with your external equipment. Please check your connections. If the problem still persists, refer to

N

Does the problem still exist with this sound test?

appears on the screen.If during the sound test you can hear sound only from one speaker or not at all, select Yes. If you can hear sound from the speakers, select No.

Yes

No

: There may be a problem with the TV. Contact Samsung’s Call Center for assistance.

the external device’s user manual.

If you hear no sound from the TV’s speakers, before performing the sound test, make sure Speaker Select is set to TV speaker

N

N in the Sound menu.

The melody will be heard during the test even if Speaker Select is set to External Speaker or the sound is muted by pressing the MMUTE button.

If headphones are connected, the test melody will play through the headphones.

„

„

Signal Strength (Digital channels only)

You can adjust your antenna to improve the reception of available digital channels.

N

If the signal strength meter indicates that the signal is weak, physically adjust your antenna to increase the signal strength.

Continue to adjust the antenna until you fi nd the best position with the strongest signal.

Software Upgrade

To keep your product up-to-date with new Digital Television features then software upgrades are periodically broadcast as part of the normal Television signal. It will automatically detect these signals and display the software upgrade banner. You are given the option to install the upgrade.

By USB

Insert a USB drive containing the fi rmware upgrade into TV. Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the fi rmware upgrade. Please check the fi rmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings. We recommend you write down your settings so that you can easily reset them after the upgrade.

TV Rear Panel

USB Drive

„ By Channel

Upgrades the software using the broadcasting signal.

„ Standby Mode Upgrade

To continue software upgrade with master power on, select on by pressing the ▲ or ▼ button. 45 minutes after entering standby mode, a manual upgrade is automatically conducted. Since the power of the unit is turned on internally, the screen may be on slightly for the product. This phenomenon may continue for more than 1 hour until the software upgrade is completed.

„

Alternative Software

Replace the current software with the alternative.

HD Connection Guide

The brief instruction on How to get the best performance from your HD TV is displayed. We offer the connection method for HD devices.

Contact Samsung

You can know the Samsung Call center, website and information for product.

N

You can move the previous or next page by pressing the ▲ or ▼ button.

English - 27

BN68-02013A_Eng.indd 27 2009-09-18 �� 9:25:48

About Anynet+

Connecting Anynet+ Devices

Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung TV’s remote.

The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your Samsung device has this feature, check if there is an Anynet+ logo on it.

To connect to a TV

TV

Anynet+

Device 1

Anynet+

Device 2

Anynet+

Device 3

HDMI 1.3 Cable

HDMI 1.3 Cable

HDMI 1.3 Cable

1. Connect the [HDMI 1], [HDMI 2(DVI) or [HDMI 3] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI cable.

To connect to Home Theater

TV

Home Theatre Anynet+ Device 1

Optical Cable

HDMI 1.3 Cable

Anynet+ Device 2

HDMI 1.3 Cable

Anynet+ Device 3

HDMI 1.3 Cable

HDMI 1.3 Cable

N

N

N

N

1. Connect the [HDMI 1], [HDMI 2(DVI)], or [HDMI 3] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI cable.

2. Connect the HDMI IN jack of the home theater and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI cable.

N

N

Connect the Optical cable between the Digital Audio Out (Optical) jack on your TV and the Digital Audio Input on the Home Theater.

When following the connection above, the Optical jack only outputs 2 channel audio. You will only hear sound from the Home

Theater’s Front Left and Right speakers and the subwoofer. If you want to hear 5.1 channel audio, connect the Digital Audio Out

(Optical) jack on the DVD player or Cable/Satellite Box (ie Anynet Device 1 or 2) directly to the Amplifi er or Home Theater, not the

TV.

Connect only one Home Theater.

You can connect an Anynet + device using the HDMI 1.3 cable. Some HDMI cables may not support Anynet+ functions.

Anynet + works when the AV device supporting Anynet+ is in the Standby or On status.

Anynet + supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.

English - 28

BN68-02013A_Eng.indd 28 2009-09-18 �� 9:25:50

Setting Up Anynet+

The following settings help set the Anynet+ functions.

T

Press the TOOLS button to display Tools menu.

You can also display Anynet+ menu by selecting ToolsAnynet+(HDMI-CEC).

Setup

„

Anynet+(HDMI-CEC) → Off / On

To use the Anynet+ Function, Anynet+ (HDMI-CEC) must be set to On.

N

When the Anynet+ (HDMI-CEC) function is disabled, all the Anynet+ related operations are deactivated.

„

Auto Turn Off → Yes / No

Setting an Anynet+ Device to turn Off Automatically when the TV is Turned Off

N

The active source on the TV remote must be set to TV to use the Anynet + function.

N

If you set Auto Turn Off to Yes, connected external devices are also turned off when the TV is turned off. If an external device is still recording, it may or may not turn off.

Device List

Setup

Anynet+ (HDMI-CEC)

U Move E Enter R Return

Setup

Auto Turn Off

U Move E Enter R Return

Scanning and Switching between Anynet+ Devices

N

N

N

N

1. Press the TOOLS button. Press the ENTERE button to select

Anynet+ (HDMI-CEC).

2. Press the ▲ or ▼ button to select Device List, then press the ENTERE button.

N

N

Anynet+ devices connected to the TV are listed. If you cannot find a device you want, press the red button to scan for devices.

Only when you set Anynet+ (HDMI-CEC) to On in the Setup menu, the Device

List menu appears.

3. Press the ▲ or ▼ button to select to a particular device and press the ENTERE button. It is switched to the selected device.

N

View TV

Device List

Record

DVDR MENU

DVDR INFO

Receiver

Setup

:

:

DVDR

On

U Move E Enter R Return

Switching to the selected devices may take up to 2 minutes. You cannot cancel the operation during the switching operation.

The time required to scan for devices is determined by the number of connected devices.

When the device scan is complete, the number of devices found are not displayed.

Although the TV automatically searches the device list when the TV is turned on via the power button, devices connected to the TV when the TV is on or under some conditions are not automatically displayed in the device list. Press the red button to search for the connected device.

If you have selected external input mode by pressing the SOURCE button, you cannot use the Anynet+ function. Make sure to switch to an Anynet+ device by using the Device List.

Continued...

English - 29

BN68-02013A_Eng.indd 29 2009-09-18 �� 9:25:51

Anynet + Menu

The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV.

Anynet+ Menu

View TV

Device List

(device_name) MENU

Description

Anynet+ mode changes to TV broadcast mode.

Shows the Anynet+ device list.

Shows the connected device menus. E.g. If a DVD recorder is connected, the disc menu of the

DVD recorder will appear.

(device_name) INFO

Record: (*recorder)

Shows the play menu of the connected device. E.g. If a DVD recorder is connected, the play menu of the DVD recorder will appear.

Starts recording immediately using the recorder. (This is only available for devices that support the recording function.)

(*recorder) Reserve Recording Enables reserving a recording for the recorder. (This is only available for devices that support the recording reservation function.)

Stop Recording: (*recorder)

Receiver

Stops recording.

Sound is played through the receiver.

N

If more than one recording device is connected, they are displayed as (*recorder) and if only one recording device is connected, it will be represented as (*device_name).

TV Remote Control Buttons Available in Anynet+ Mode

Device Type

Anynet+ Device

Device with built-in Tuner

Operating Status

After switching to the device, when the menu of the corresponding device is displayed on the screen.

After switching to the device, while playing a file

After switching to the device, when you are watching a TV programme

Available Buttons

Numeric buttons

▲/▼/◄/►/ ENTERE buttons

Colour buttons / EXIT button

(Backward search) / (Forward search) (Stop) / (Play) /

(Pause)

P / button

Audio Device When Receiver is activated

=

/ button

M MUTE button

N

N

N

N

N

N

The Anynet+ function only works when the active source on the TV remote control is set to TV.

The button works only while in the recordable state.

You cannot control Anynet+ devices using the buttons on the TV. You can control Anynet+ devices only using the TV remote control.

The TV remote control may not work under certain conditions. In this case, reselect the Anynet+ device.

The Anynet+ functions do not operate with other manufacturers’ products.

The , operations may differ depending on the device.

Recording

You can make a recording of a TV programme using a Samsung recorder.

1. Press the TOOLS button. Press the ENTERE button to select

N

N

N

Anynet+ (HDMI-CEC).

2. Press the ▲ or ▼ button to select Record: (device_name), then press the

ENTERE button. Recording begins.

View TV

Device List

Record

DVDR MENU

: DVDR

N

N

When there is more than one recording device

When multiple recording devices are connected, the recording devices are listed.

Press the ▲ or ▼ button to select a recording device and press the ENTERE button. Recording begins.

When the recording device is not displayed

Select Device List and press the red button to search devices.

DVDR INFO

Receiver

Setup

: On

U Move E Enter R Return

You can record the source streams by selecting Record: (device_name).

Pressing the button will record whatever you are currently watching. If you are watching video from another device, the video from the device is recorded.

Before recording, check whether the antenna jack is properly connected to the recording device. To properly connect an antenna to a recording device, refer to the recording device’s users manual.

English - 30

BN68-02013A_Eng.indd 30 2009-09-18 �� 9:25:51

Listening through a Receiver (Home theater)

You can listen to sound through a receiver instead of the TV speaker.

1. Press the TOOLS button. Press the ENTERE button to select Anynet+ (HDMI-CEC).

2. Press the ▲ or ▼ button to select Receiver. Press the ◄ or ► button to select On or Off.

N

N

N

N

N

View TV

Device List

If your receiver supports audio only, it may not appear in the device list.

The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of the TV.

When the receiver (home theater) is set to On, you can hear sound output from the

Record

DVDR MENU

DVDR INFO

Receiver

Setup

:

DVDR

On ►

TV’s Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digital component

U Move E Enter R Return such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver.

When listening through the receiver, there are restrictions for using the audio-related menus.

If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power failure), the

Speaker Select may be set to External Speaker when you turn the TV on again. (see page 22)

Troubleshooting for Anynet+

Symptom

Anynet+ does not work.

I want to start Anynet+.

I want to exit Anynet+.

The message Connecting to

Anynet+ device... appears on the screen.

The Anynet+ device does not play.

The connected device is not displayed.

The TV programme cannot be recorded.

The TV sound is not output through the receiver.

Solution

• Check if the device is an Anynet+ device. The Anynet+ system supports Anynet + devices only.

Connect only one receiver (home theater).

Check if the Anynet

Check the Anynet

+ device power cord is properly connected.

+ device’s Video/Audio/HDMI 1.3 cable connections.

Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

Check whether the TV remote control is in TV mode.

Check whether it is Anynet + exclusive remote control.

Anynet+ doesn’t work in certain situations. (Searching channels, Operating WISELINK Pro,

Plug & Play, etc.)

When connecting or removing the HDMI 1.3 cable, please make sure to search devices again or turn your TV off and on again.

Check if the Anynet + Function of Anynet+ device is set on.

Check if the Anynet+ device is properly connected to the TV and check if the Anynet+

(HDMI-CEC) is set to On in the Anynet+ Setup menu.

Press the

Select View TV in the Anynet

Press the

TV button on the TV remote control to switch to TV. Then press the TOOLS button to show the Anynet+ menu and select a menu you want.

+ menu.

SOURCE button on the TV remote control and select a device other than Anynet+ devices.

(Note that the channel button operates only when a tuner-embedded Anynet connected.)

+ device is not

You cannot use the remote control when you are configuring Anynet + or switching to a view mode.

Use the remote control when the Anynet + setting or switching to view mode is complete.

You cannot use the play function when Plug & Play is in progress.

• Check whether or not the device supports Anynet + functions.

Check whether or not the HDMI 1.3 cable is properly connected.

Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

Search Anynet + devices again.

You can connect an Anynet + device using the HDMI 1.3 cable only. Some HDMI cables may not support Anynet+ functions.

If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a power failure, please repeat the device scan.

Check whether the antenna jack on the recording device is properly connected.

• Connect the optical cable between TV and the receiver.

English - 31

BN68-02013A_Eng.indd 31 2009-09-18 �� 9:25:51

Recommendations for Use

Teletext Feature

Most television stations provide written information services via Teletext. The index page of the teletext service gives you information on how to use the service. In addition, you can select various options to suit your requirements by using the remote control buttons.

N

For teletext information to be displayed correctly, channel reception must be stable. Otherwise, information may be missing or some pages may not be displayed.

1 : (exit)

Exit from the teletext display.

2 6 (index)

Used to display the index (contents) page at any time while you are viewing teletext.

3 8 (store)

Used to store the teletext pages.

4 4 (size)

Press to display the double-size letters in the upper half of the screen. For lower half of the screen, press it again. To display normal screen, press it once again.

1

5 5 (reveal)

Used to display the hidden text (answers to quiz games, for example). To display normal screen, press it again.

6 / (teletext on/mix)

Press to activate teletext mode after selecting the channel providing the teletext service.

Press it twice to overlap the teletext with the current broadcasting screen.

2

3

7

8

9

0

7 1 (sub-page)

Used to display the available sub-page.

8 2 (page up)

Used to display the next teletext page.

9 3 (page down)

Used to display the previous teletext page.

0 0 (mode)

Press to select the teletext mode (LIST/FLOF). If you press it in the LIST mode, it switches into the List save mode. In the List save mode, you can save teletext page into list using the 8(store) button.

!

9 (hold)

Used to hold the display on a given page if the selected page is linked with several secondary pages which follow on automatically. To resume, press it again.

4

5

6

!

@

#

@ 7 (cancel)

Used to display the broadcast when searching for a page.

# Colour buttons (red/green/yellow/blue)

If the FASTEXT system is used by a broadcasting company, the different topics covered on a teletext page are colour-coded and can be selected by pressing the coloured buttons. Press one of them corresponding to the required. The page is displayed with other coloured information that can be selected in the same way. To display the previous or next page, press the corresponding coloured button.

N

You can change teletext pages by pressing the numeric buttons on the remote control.

Continued...

English - 32

BN68-02013A_Eng.indd 32 2009-09-18 �� 9:25:52

The teletext pages are organized according to six categories:

Part Contents

A Selected page number.

B Broadcasting channel identity.

C Current page number or search indications.

D Date and time.

E Text.

F Status information.

FASTEXT information.

N

-

-

-

Teletext information is often divided between several pages displayed in sequence, which can be accessed by:

Entering the page number

Selecting a title in a list

Selecting a coloured heading (FASTEXT system)

O

Press the TV button to exit from the teletext display.

Wall Mount Kit Specifications (VESA)

Install your wall mount on a solid wall perpendicular to the floor.

When attaching to other building materials, please contact your nearest dealer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.

Product Family

LCD-TV inch

19" ~22"

23"~29"

30"~40"

46"~55"

57"~70"

VESA Spec. (A * B) Standard Screw Quantity

100 * 100

M4

200 * 100

200 * 200 M6

4

400 * 400

800 * 400

1400 * 800

M8

80" ~

42"~ 50" 400 * 400

58"~ 63" 600 * 400

PDP-TV

800 * 400

1400 * 800

M8 4

70" ~

80" ~

N

N

N

N

N

N

N

N

We provided the standard dimensions for wall mount kits as shown in the table above.

When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.

Do not use screws longer than the standard dimension, as they may cause damage to the inside of the TV set.

For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifications.

Do not use screws that do not comply with the VESA standard screw specifications.

Do not use fasten the screws too strongly, this may damage the product or cause the product to fall, leading to personal injury.

Samsung is not liable for these kinds of accidents.

Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.

Our 57” and 63” models do not comply with VESA Specifications. Therefore, you should use our dedicated wall mount kit for this model.

Do not exceed 15 degrees tilt when mounting this TV.

Do not install your Wall Mount Kit while your TV is turned on.

It may result in personal injury due to electric shock.

English - 33

BN68-02013A_Eng.indd 33 2009-09-18 �� 9:25:52

Preparing before installing Wall- Mount on the wall

Case A. Installing SAMSUNG Wall-Mount Case B. Installing other company’s Wall-Mount

경고

경고

1. Install Wall Mount with the torque range of 15kgf·cm or less. Make sure that parts can be damaged if the torque is out of the specified range.

2. Accessory Kit contains Holder–Ring [①] for installing other company’s Wall-Mount on Samsung TV. (Case B)

주의

Securing the TV to the Wall

Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang

주의 safety precautions provided on the included Safety Flyer. For added stability, install the anti-fall device for safety purposes, as follows.

Wall

Wall

To avoid the TV from falling

1. Put the screws into the clamps and firmly fasten them onto the wall. Confirm that the screws have been firmly installed onto the wall.

N

N

You may need additional material such as an anchor depending on the type of wall.

Since the necessary clamps, screws, and string are not supplied, please purchase these additionally.

2. Remove the screws from the center back of the TV, put the screws into the clamps, and then fasten the screws onto the TV again.

N

Screws may not be supplied with the product.

3. Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong string and then tie the string tightly.

N

N

N

Install the TV near to the wall so that it does not fall backwards .

It is safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on the TV.

Untie the string before moving the TV.

4. Verify all connections are properly secured. Periodically check connections for any sign of fatigue for failure. If you have any doubt about the security of your connections,contact a professional installer.

English - 34

BN68-02013A_Eng.indd 34 2009-09-18 �� 9:25:53

10 cm

Securing the Installation Space

Keep the required distances between the product and other objects (e.g. walls) to ensure proper ventilation.

Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature of the product.

Install the product so the required distances shown in the figure are kept.

N

N

When using a stand or wall-mount, use parts provided by Samsung Electronics only.

If you use parts provided by another manufacturer, it may result in a problem with the product or an injury due to the product

falling.

If you use parts provided by another manufacturer, it may result in a problem with the product or fire due to an increase in the internal temperature of the product due to poor ventilation.

The appearance may differ depending on the product.

„

When installing the product with a stand

„

When installing the product with a wall-mount

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

10 cm

BN68-02013A_Eng.indd 35

English - 35

2009-09-18 �� 9:25:53

Troubleshooting

If the TV seems to have a problem, first try this list of possible problems and solutions.

Problem Possible Solution

Picture Quality

First of all, please perform the Picture Test to confirm that your TV is properly displaying test image.

* Go to MENUSupportSelf DiagnosisPicture Test

If the test image is properly displayed, the poor picture may caused by the source or signal.

TV image does not look as good as it did in the store.

Picture is distorted: macroblock,small block, dots,pixelization.

Wrong or missing color with

Component connection.

Poor color or brightness.

Dotted line on the edge of screen.

If you have an analog Cable/Set top box, upgrade to an Box.

Use HDMI or Component cables to deliver HD picture quality.

Cable/Satellite subscriber : Try HD (High Definition) stations from channel line up.

Antenna connection: Try HD stations after performing Auto program

N

Many HD channels are upscaled from SD (Standard Definition) contents.

Adjust Cable/Set top video output resolution to 1080i or 720p.

Compression of video contents may cause picture distortion especially on fast moving pictures such as sports and action movies.

Low signal level can cause picture distortion. This is not a TV issue. Have the antenna accessed.

• Make sure the Component cables are connected to the correct jacks.

Incorrect or loose connections may cause color problems or the screen will be blank.

Adjust Picture options in the TV menu (Picture Mode, Colour, Brightness,

Sharpness).

Adjust Energy Saving option in Setup menu.

Try picture reset to view the default picture setting.

(Go to MENUPicturePicture Reset)

If picture size is set to Just scan, change to 16:9.

Change cable/satellite box resolution.

Picture is black and white with AV

(Composite) input only.

Picture freezes or is distorted when changing channels or picture is delayed.

• Confirm Composite (yellow) cable is in yellow jack in source as well as TV.

If connected with cable /set top box, please try to reset cable box. (reconnect AC cord and wait until cable box reboots. It may take up to 20 minutes)

Set output resolution of cable box to 1080i or 720p

Sound Quality

First of all, please perform the Sound Test to confirm that your TV audio is properly operating.

* Go to MENUSupportSelf DiagnosisSound Test

If the audio is OK, the sound problem may caused by the source or signal.

No sound or sound is too low at maximum volume.

Picture is good but no sound.

Noise from speaker.

Please check the volume of device (Cable/Sat Box, DVD, Blu-ray etc) connected to your TV.

Then, adjust the TV volume accordingly.

Set the Speaker Select option to TV speaker in the sound menu.

Make sure audio cables from an external device are connected to correct audio input jacks on the TV.

Check connected device's audio output option.

Ex) You may need to change your cable box' audio option to HDMI when you have

HDMI connected to your TV.

If you are using a DVI to HDMI cable, a separate audio cable is required.

Remove plug from headphone jack (if available on your TV).

Reboot the connected device by reconnecting the device’s power cable.

Check cable connections. Make sure a video cable is not connected to an audio input.

For Antenna/Cable connection, check signal strength. Low signal level may cause sound distortion.

BN68-02013A_Eng.indd 36

English - 36

Continued...

2009-09-18 �� 9:25:53

Problem

No Picture, No Video

TV won't turn on.

Possible Solution

TV turns off automatically.

No picture/Video.

Make sure the AC power cord is plugged in securely to the wall outlet and the TV.

Make sure the wall outlet is working.

Try pressing the Power button on the TV to make sure the remote is working properly.

If the TV turns on, it may be caused by Remote Control.

To fix the Remote problem, refer to "Remote control does not work" below.

• Check if the Sleep Timer is set to On in the Setup menu.

If connected the TV to your PC, check your PC power settings.

Make sure the AC power cord is plugged in securely to the wall outlet and the TV.

If there is no signal for about 10 ~ 15 minutes with Antenna/Cable connection, the TV will turn off.

Check cable connections. (remove and reconnect all cables of TV and external devices)

Set your external device's (Cable/Sat Box, DVD, Blu-ray etc) video output to match the connections to the TV input. For example, external device's output : HDMI , TV's input : HDMI.

Make sure your connected device is powered on.

Make sure to select the TV's correct source by pressing the remote control.

SOURCE button on the

Reboot the connected device by reconnecting the device’s power cable.

RF (Cable/Antenna) Connection

Cannot receive all channels.

Picture is distorted : macroblock,small block,dots,pixelization.

• Make sure coaxial cable is connected securely.

Please try Plug & Play to add available channels to the channel list.

Go to MENUSetup Plug & Play and wait for all available channels are stored.

Verify Antenna is positioned correctly.

Compression of video contents may cause picture distortion especially on fast moving pictures such as sports and action movies.

Low signal level can cause picture distortion. This is not a TV issue. Have the antenna accessed

PC Connection

“Not Supported Mode” message.

PC is always shown on source list even if not connected.

Video is OK but there is no audio with

HDMI connection.

• Set your PC's output resolution so it matches the resolutions supported by the TV.

This is normal; PC is always shown on the source list even though a PC is not connected.

• Check the audio output setting on your PC.

BN68-02013A_Eng.indd 37

English - 37

Continued...

2009-09-18 �� 9:25:53

Problem Possible Solution

Others

Picture is not shown in full screen.

Remote control does not work.

Plasma TV is making humming noise.

Image Retention (Burn In) Issue.

Can not control TV power or volume with Cable/Sat box remote control.

“Not Supported Mode” message.

Plastic smell from TV.

TV Signal Strength is unavailable in the

Self Diagnostic Test menu.

TV is tilted to right or left side.

Can not assemble stand base.

Channel menu is grey out (unavailable).

Your settings are lost after 30 minutes or every time TV is turned off.

Intermittent loss of audio or video.

Black bars on each side will be shown on HD channels when displaying upscaled SD

(4:3) contents.

Black bars on Top & Bottom will be shown on movies that have aspect ratios different from your TV.

Adjust picture size option on your external device or TV to full screen.

Replace the remote control batteries with correct polarity (+ -).

Clean the transmission window located on the top of the remote.

Try pointing the remote directly at the TV from 5~6 feet away.

Plasma TVs typically make a soft humming sound. This is normal. It’s caused by the electrical charges that are used to create the images on the screen.

If the humming sound is loud, you may have set the brightness on the TV too high.

Try setting the brightness lower.

You can also have loud humming if the back of your Plasma TV is too close to a wall or other hard surface. Also try rerouting your connection cables.

Improper installation of wall mount can create excessive noise.

To minimize the possibility of screen burn, this unit is equipped with screen burn reduction technology. Pixel Shift technology enables you to set picture movement up/ down (Vertical Line) and side to side (Horizontal Dot).

• Program the Cable/Set top box remote control to operate the TV.

Refer to Cable/Set top box user manual for SAMSUNG TV code.

• Check the supported resolution of the TV and adjust the external device's output resolution accordingly. Refer to resolution settings in this manual.

• This smell is normal and will dissipate over time.

• This function is only available with digital channels with an Antenna (RF/Coax) connection.

• Remove the stand base from TV and reassemble.

• Make sure TV is placed on flat surface.

If can not remove screws from TV, please use magnetized screw driver.

• Channel menu is only available when TV source is selected.

If TV is in the Store Demo mode, it will reset audio and picture settings every

30 minutes.

Please change from Store Demo mode to Home Use mode in the Plug & Play procedure.

Press the SOURCE button to select TV mode, go to MENUSetupPlug & Play

ENTER

Check cable connections and reconnect.

Can be caused by using overly rigid or thick cables.

Make sure the cables are flexible enough for long term use.

If wall mounting, we recommend using cables with 90 degree connectors.

You may see small particles if you look closely at the edge of the bezel surrounding the TV screen.

• This is part of the product’s design and is not a defect.

N Some of above pictures and functions are available at specific models only.

English - 38

BN68-02013A_Eng.indd 38 2009-09-18 �� 9:25:53

Specifications

The descriptions and characteristics in this booklet are given for information purposes only and are subject to modification without notice.

Model Name

Screen Size (Diagonal)

PC Resolution (Optimum)

Sound (Output)

Dimension (WxHxD)

Body

With stand

Weight

Body

With stand

Environmental Considerations

Operating Temperature

Operating Humidity

Storage Temperature

Storage Humidity

PS42B450

42 inch

1024 x 768 @ 60 Hz

10 W x 2

1056 x 660 x 74 mm

1056 x 721 x 316 mm

24 kg

28 kg

50 °F to 104 °F (10 °C to 40 °C)

10% to 80%, non-condensing

-4 °F to 113 °F (-20 °C to 45 °C)

5% to 95%, non-condensing

PS50B450

50 inch

1360 x 768 @ 60 Hz

10 W x 2

1221 x 749 x 74 mm

1221 x 810 x 316 mm

31 kg

35 kg

N

N

N

This device is a Class B digital apparatus.

Design and specifications are subject to change without prior notice.

For the power supply and Power Consumption, refer to the label attached to the product.

BN68-02013A_Eng.indd 39

English - 39

2009-09-18 �� 9:25:54

This page is intentionally left blank.

BN68-02013A_Eng.indd 40 2009-09-18 �� 9:25:54

This page is intentionally left blank.

BN68-02013A_Eng.indd 41 2009-09-18 �� 9:25:54

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.

Country

AUSTRALIA

CHINA

HONG KONG

INDIA

INDONESIA

JAPAN

MALAYSIA

New zealand

PHILIPPINES

SINGAPORE

SOUTH AFRICA

TAIWAN

THAILAND

Turkey

U.A.E

VIETNAM

3698-4698

Customer Care Centre

1300 362 603

400-810-5858

010-6475 1880

3030 8282

1800 110011

1800 3000 8282

0800-112-8888

0120-327-527

1800-88-9999

0800 SAMSUNG (0800 726 786)

1-800-10-SAMSUNG(726-7864)

1-800-3-SAMSUNG(726-7864)

1-800-8-SAMSUNG(726-7864)

02-5805777

1800-SAMSUNG(726-7864)

0860-SAMSUNG(726-7864 )

0800-329-999

1800-29-3232

02-689-3232

444 77 11

800-SAMSUNG (726-7864)

8000-4726

1 800 588 889

Web Site www.samsung.com/au www.samsung.com/cn www.samsung.com/hk www.samsung.com/hk_en/ www.samsung.com/in www.samsung.com/id www.samsung.com/jp www.samsung.com/my www.samsung.com/nz www.samsung.com/ph www.samsung.com/sg www.samsung.com/za www.samsung.com/tw www.samsung.com/th www.samsung.com/tr www.samsung.com/ae www.samsung.com/vn

BN68-02013A_Eng.indd 42

BN68-02013A-01

2009-09-18 �� 9:25:54

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Download PDF

advertisement